I2C for OMAP platforms
Required properties :
-- compatible : Must be "ti,omap3-i2c" or "ti,omap4-i2c"
+- compatible : Must be "ti,omap2420-i2c", "ti,omap2430-i2c", "ti,omap3-i2c"
+ or "ti,omap4-i2c"
- ti,hwmods : Must be "i2c<n>", n being the instance number (1-based)
- #address-cells = <1>;
- #size-cells = <0>;
* they probably share the same GPIO IRQ
* REVISIT: Add timing support from slls644g.pdf
*/
- 8250@3,0 {
+ uart@3,0 {
compatible = "ns16550a";
reg = <3 0 0x100>;
bank-width = <2>;
*/
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/pinctrl/omap.h>
#include "skeleton.dtsi"
serial0 = &uart1;
serial1 = &uart2;
serial2 = &uart3;
+ i2c0 = &i2c1;
+ i2c1 = &i2c2;
};
cpus {
ranges;
ti,hwmods = "l3_main";
+ aes: aes@480a6000 {
+ compatible = "ti,omap2-aes";
+ ti,hwmods = "aes";
+ reg = <0x480a6000 0x50>;
+ dmas = <&sdma 9 &sdma 10>;
+ dma-names = "tx", "rx";
+ };
+
+ hdq1w: 1w@480b2000 {
+ compatible = "ti,omap2420-1w";
+ ti,hwmods = "hdq1w";
+ reg = <0x480b2000 0x1000>;
+ interrupts = <58>;
+ };
+
+ mailbox: mailbox@48094000 {
+ compatible = "ti,omap2-mailbox";
+ ti,hwmods = "mailbox";
+ reg = <0x48094000 0x200>;
+ interrupts = <26>;
+ };
+
intc: interrupt-controller@1 {
compatible = "ti,omap2-intc";
interrupt-controller;
sdma: dma-controller@48056000 {
compatible = "ti,omap2430-sdma", "ti,omap2420-sdma";
+ ti,hwmods = "dma";
reg = <0x48056000 0x1000>;
interrupts = <12>,
<13>,
#dma-requests = <64>;
};
+ i2c1: i2c@48070000 {
+ compatible = "ti,omap2-i2c";
+ ti,hwmods = "i2c1";
+ reg = <0x48070000 0x80>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <56>;
+ dmas = <&sdma 27 &sdma 28>;
+ dma-names = "tx", "rx";
+ };
+
+ i2c2: i2c@48072000 {
+ compatible = "ti,omap2-i2c";
+ ti,hwmods = "i2c2";
+ reg = <0x48072000 0x80>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <57>;
+ dmas = <&sdma 29 &sdma 30>;
+ dma-names = "tx", "rx";
+ };
+
+ mcspi1: mcspi@48098000 {
+ compatible = "ti,omap2-mcspi";
+ ti,hwmods = "mcspi1";
+ reg = <0x48098000 0x100>;
+ interrupts = <65>;
+ dmas = <&sdma 35 &sdma 36 &sdma 37 &sdma 38
+ &sdma 39 &sdma 40 &sdma 41 &sdma 42>;
+ dma-names = "tx0", "rx0", "tx1", "rx1",
+ "tx2", "rx2", "tx3", "rx3";
+ };
+
+ mcspi2: mcspi@4809a000 {
+ compatible = "ti,omap2-mcspi";
+ ti,hwmods = "mcspi2";
+ reg = <0x4809a000 0x100>;
+ interrupts = <66>;
+ dmas = <&sdma 43 &sdma 44 &sdma 45 &sdma 46>;
+ dma-names = "tx0", "rx0", "tx1", "rx1";
+ };
+
+ rng: rng@480a0000 {
+ compatible = "ti,omap2-rng";
+ ti,hwmods = "rng";
+ reg = <0x480a0000 0x50>;
+ interrupts = <36>;
+ };
+
+ sham: sham@480a4000 {
+ compatible = "ti,omap2-sham";
+ ti,hwmods = "sham";
+ reg = <0x480a4000 0x64>;
+ interrupts = <51>;
+ dmas = <&sdma 13>;
+ dma-names = "rx";
+ };
+
uart1: serial@4806a000 {
compatible = "ti,omap2-uart";
ti,hwmods = "uart1";
+ reg = <0x4806a000 0x2000>;
+ interrupts = <72>;
+ dmas = <&sdma 49 &sdma 50>;
+ dma-names = "tx", "rx";
clock-frequency = <48000000>;
};
uart2: serial@4806c000 {
compatible = "ti,omap2-uart";
ti,hwmods = "uart2";
+ reg = <0x4806c000 0x400>;
+ interrupts = <73>;
+ dmas = <&sdma 51 &sdma 52>;
+ dma-names = "tx", "rx";
clock-frequency = <48000000>;
};
uart3: serial@4806e000 {
compatible = "ti,omap2-uart";
ti,hwmods = "uart3";
+ reg = <0x4806e000 0x400>;
+ interrupts = <74>;
+ dmas = <&sdma 53 &sdma 54>;
+ dma-names = "tx", "rx";
clock-frequency = <48000000>;
};
dma-names = "tx", "rx";
};
+ msdi1: mmc@4809c000 {
+ compatible = "ti,omap2420-mmc";
+ ti,hwmods = "msdi1";
+ reg = <0x4809c000 0x80>;
+ interrupts = <83>;
+ dmas = <&sdma 61 &sdma 62>;
+ dma-names = "tx", "rx";
+ };
+
timer1: timer@48028000 {
compatible = "ti,omap2420-timer";
reg = <0x48028000 0x400>;
ti,hwmods = "timer1";
ti,timer-alwon;
};
+
+ wd_timer2: wdt@48022000 {
+ compatible = "ti,omap2-wdt";
+ ti,hwmods = "wd_timer2";
+ reg = <0x48022000 0x80>;
+ };
};
};
+
+&i2c1 {
+ compatible = "ti,omap2420-i2c";
+};
+
+&i2c2 {
+ compatible = "ti,omap2420-i2c";
+};
dma-names = "tx", "rx";
};
+ mmc1: mmc@4809c000 {
+ compatible = "ti,omap2-hsmmc";
+ reg = <0x4809c000 0x200>;
+ interrupts = <83>;
+ ti,hwmods = "mmc1";
+ ti,dual-volt;
+ dmas = <&sdma 61>, <&sdma 62>;
+ dma-names = "tx", "rx";
+ };
+
+ mmc2: mmc@480b4000 {
+ compatible = "ti,omap2-hsmmc";
+ reg = <0x480b4000 0x200>;
+ interrupts = <86>;
+ ti,hwmods = "mmc2";
+ dmas = <&sdma 47>, <&sdma 48>;
+ dma-names = "tx", "rx";
+ };
+
timer1: timer@49018000 {
compatible = "ti,omap2420-timer";
reg = <0x49018000 0x400>;
ti,hwmods = "timer1";
ti,timer-alwon;
};
+
+ mcspi3: mcspi@480b8000 {
+ compatible = "ti,omap2-mcspi";
+ ti,hwmods = "mcspi3";
+ reg = <0x480b8000 0x100>;
+ interrupts = <91>;
+ dmas = <&sdma 15 &sdma 16 &sdma 23 &sdma 24>;
+ dma-names = "tx0", "rx0", "tx1", "rx1";
+ };
+
+ usb_otg_hs: usb_otg_hs@480ac000 {
+ compatible = "ti,omap2-musb";
+ ti,hwmods = "usb_otg_hs";
+ reg = <0x480ac000 0x1000>;
+ interrupts = <93>;
+ };
+
+ wd_timer2: wdt@49016000 {
+ compatible = "ti,omap2-wdt";
+ ti,hwmods = "wd_timer2";
+ reg = <0x49016000 0x80>;
+ };
};
};
+
+&i2c1 {
+ compatible = "ti,omap2430-i2c";
+};
+
+&i2c2 {
+ compatible = "ti,omap2430-i2c";
+};
obj-$(CONFIG_ARCH_OMAP2) += $(omap-2-3-common) $(hwmod-common)
obj-$(CONFIG_ARCH_OMAP3) += $(omap-2-3-common) $(hwmod-common) $(secure-common)
-obj-$(CONFIG_ARCH_OMAP4) += prm44xx.o $(hwmod-common) $(secure-common)
+obj-$(CONFIG_ARCH_OMAP4) += $(hwmod-common) $(secure-common)
obj-$(CONFIG_SOC_AM33XX) += irq.o $(hwmod-common)
-obj-$(CONFIG_SOC_OMAP5) += prm44xx.o $(hwmod-common) $(secure-common)
+obj-$(CONFIG_SOC_OMAP5) += $(hwmod-common) $(secure-common)
obj-$(CONFIG_SOC_AM43XX) += $(hwmod-common) $(secure-common)
-obj-$(CONFIG_SOC_DRA7XX) += prm44xx.o $(hwmod-common) $(secure-common)
+obj-$(CONFIG_SOC_DRA7XX) += $(hwmod-common) $(secure-common)
ifneq ($(CONFIG_SND_OMAP_SOC_MCBSP),)
obj-y += mcbsp.o
extern void omap_sdrc_init(struct omap_sdrc_params *sdrc_cs0,
struct omap_sdrc_params *sdrc_cs1);
struct omap2_hsmmc_info;
-extern int omap4_twl6030_hsmmc_init(struct omap2_hsmmc_info *controllers);
extern void omap_reserve(void);
struct omap_hwmod;
#include "soc.h"
#include "iomap.h"
-#include "mux.h"
#include "control.h"
#include "display.h"
#include "prm.h"
{ "dss_hdmi", "omapdss_hdmi", -1 },
};
-static void __init omap4_tpd12s015_mux_pads(void)
-{
- omap_mux_init_signal("hdmi_cec",
- OMAP_PIN_INPUT_PULLUP);
- omap_mux_init_signal("hdmi_ddc_scl",
- OMAP_PIN_INPUT_PULLUP);
- omap_mux_init_signal("hdmi_ddc_sda",
- OMAP_PIN_INPUT_PULLUP);
-}
-
-static void __init omap4_hdmi_mux_pads(enum omap_hdmi_flags flags)
-{
- u32 reg;
- u16 control_i2c_1;
-
- /*
- * CONTROL_I2C_1: HDMI_DDC_SDA_PULLUPRESX (bit 28) and
- * HDMI_DDC_SCL_PULLUPRESX (bit 24) are set to disable
- * internal pull up resistor.
- */
- if (flags & OMAP_HDMI_SDA_SCL_EXTERNAL_PULLUP) {
- control_i2c_1 = OMAP4_CTRL_MODULE_PAD_CORE_CONTROL_I2C_1;
- reg = omap4_ctrl_pad_readl(control_i2c_1);
- reg |= (OMAP4_HDMI_DDC_SDA_PULLUPRESX_MASK |
- OMAP4_HDMI_DDC_SCL_PULLUPRESX_MASK);
- omap4_ctrl_pad_writel(reg, control_i2c_1);
- }
-}
-
-static int omap4_dsi_mux_pads(int dsi_id, unsigned lanes)
-{
- u32 enable_mask, enable_shift;
- u32 pipd_mask, pipd_shift;
- u32 reg;
-
- if (dsi_id == 0) {
- enable_mask = OMAP4_DSI1_LANEENABLE_MASK;
- enable_shift = OMAP4_DSI1_LANEENABLE_SHIFT;
- pipd_mask = OMAP4_DSI1_PIPD_MASK;
- pipd_shift = OMAP4_DSI1_PIPD_SHIFT;
- } else if (dsi_id == 1) {
- enable_mask = OMAP4_DSI2_LANEENABLE_MASK;
- enable_shift = OMAP4_DSI2_LANEENABLE_SHIFT;
- pipd_mask = OMAP4_DSI2_PIPD_MASK;
- pipd_shift = OMAP4_DSI2_PIPD_SHIFT;
- } else {
- return -ENODEV;
- }
-
- reg = omap4_ctrl_pad_readl(OMAP4_CTRL_MODULE_PAD_CORE_CONTROL_DSIPHY);
-
- reg &= ~enable_mask;
- reg &= ~pipd_mask;
-
- reg |= (lanes << enable_shift) & enable_mask;
- reg |= (lanes << pipd_shift) & pipd_mask;
-
- omap4_ctrl_pad_writel(reg, OMAP4_CTRL_MODULE_PAD_CORE_CONTROL_DSIPHY);
-
- return 0;
-}
-
-int __init omap_hdmi_init(enum omap_hdmi_flags flags)
-{
- if (cpu_is_omap44xx()) {
- omap4_hdmi_mux_pads(flags);
- omap4_tpd12s015_mux_pads();
- }
-
- return 0;
-}
-
static int omap_dsi_enable_pads(int dsi_id, unsigned lane_mask)
{
- if (cpu_is_omap44xx())
- return omap4_dsi_mux_pads(dsi_id, lane_mask);
-
return 0;
}
static void omap_dsi_disable_pads(int dsi_id, unsigned lane_mask)
{
- if (cpu_is_omap44xx())
- omap4_dsi_mux_pads(dsi_id, 0);
}
static int omap_dss_set_min_bus_tput(struct device *dev, unsigned long tput)
return ret;
}
+ /*
+ * For some GPMC devices we still need to rely on the bootloader
+ * timings because the devices can be connected via FPGA. So far
+ * the list is smc91x on the omap2 SDP boards, and 8250 on zooms.
+ * REVISIT: Add timing support from slls644g.pdf and from the
+ * lan91c96 manual.
+ */
+ if (of_device_is_compatible(child, "ns16550a") ||
+ of_device_is_compatible(child, "smsc,lan91c94") ||
+ of_device_is_compatible(child, "smsc,lan91c111")) {
+ dev_warn(&pdev->dev,
+ "%s using bootloader timings on CS%d\n",
+ child->name, cs);
+ goto no_timings;
+ }
+
/*
* FIXME: gpmc_cs_request() will map the CS to an arbitary
* location in the gpmc address space. When booting with
gpmc_read_timings_dt(child, &gpmc_t);
gpmc_cs_set_timings(cs, &gpmc_t);
+no_timings:
if (of_platform_device_create(child, NULL, &pdev->dev))
return 0;
return ret;
}
-/*
- * REVISIT: Add timing support from slls644g.pdf
- */
-static int gpmc_probe_8250(struct platform_device *pdev,
- struct device_node *child)
-{
- struct resource res;
- unsigned long base;
- int ret, cs;
-
- if (of_property_read_u32(child, "reg", &cs) < 0) {
- dev_err(&pdev->dev, "%s has no 'reg' property\n",
- child->full_name);
- return -ENODEV;
- }
-
- if (of_address_to_resource(child, 0, &res) < 0) {
- dev_err(&pdev->dev, "%s has malformed 'reg' property\n",
- child->full_name);
- return -ENODEV;
- }
-
- ret = gpmc_cs_request(cs, resource_size(&res), &base);
- if (ret < 0) {
- dev_err(&pdev->dev, "cannot request GPMC CS %d\n", cs);
- return ret;
- }
-
- if (of_platform_device_create(child, NULL, &pdev->dev))
- return 0;
-
- dev_err(&pdev->dev, "failed to create gpmc child %s\n", child->name);
-
- return -ENODEV;
-}
-
static int gpmc_probe_dt(struct platform_device *pdev)
{
int ret;
else if (of_node_cmp(child->name, "onenand") == 0)
ret = gpmc_probe_onenand_child(pdev, child);
else if (of_node_cmp(child->name, "ethernet") == 0 ||
- of_node_cmp(child->name, "nor") == 0)
+ of_node_cmp(child->name, "nor") == 0 ||
+ of_node_cmp(child->name, "uart") == 0)
ret = gpmc_probe_generic_child(pdev, child);
- else if (of_node_cmp(child->name, "8250") == 0)
- ret = gpmc_probe_8250(pdev, child);
if (WARN(ret < 0, "%s: probing gpmc child %s failed\n",
__func__, child->full_name))
{ }
#endif
+#ifdef CONFIG_SOC_HAS_REALTIME_COUNTER
void set_cntfreq(void);
+#else
+static inline void set_cntfreq(void)
+{
+}
+#endif
+
#endif /* __ASSEMBLER__ */
#endif /* OMAP_ARCH_OMAP_SECURE_H */
#include "iomap.h"
#include "common.h"
#include "mmc.h"
-#include "hsmmc.h"
#include "prminst44xx.h"
#include "prcm_mpu44xx.h"
#include "omap4-sar-layout.h"
omap_wakeupgen_init();
irqchip_init();
}
-
-#if defined(CONFIG_MMC_OMAP_HS) || defined(CONFIG_MMC_OMAP_HS_MODULE)
-static int omap4_twl6030_hsmmc_late_init(struct device *dev)
-{
- int irq = 0;
- struct platform_device *pdev = container_of(dev,
- struct platform_device, dev);
- struct omap_mmc_platform_data *pdata = dev->platform_data;
-
- /* Setting MMC1 Card detect Irq */
- if (pdev->id == 0) {
- irq = twl6030_mmc_card_detect_config();
- if (irq < 0) {
- dev_err(dev, "%s: Error card detect config(%d)\n",
- __func__, irq);
- return irq;
- }
- pdata->slots[0].card_detect_irq = irq;
- pdata->slots[0].card_detect = twl6030_mmc_card_detect;
- }
- return 0;
-}
-
-static __init void omap4_twl6030_hsmmc_set_late_init(struct device *dev)
-{
- struct omap_mmc_platform_data *pdata;
-
- /* dev can be null if CONFIG_MMC_OMAP_HS is not set */
- if (!dev) {
- pr_err("Failed %s\n", __func__);
- return;
- }
- pdata = dev->platform_data;
- pdata->init = omap4_twl6030_hsmmc_late_init;
-}
-
-int __init omap4_twl6030_hsmmc_init(struct omap2_hsmmc_info *controllers)
-{
- struct omap2_hsmmc_info *c;
-
- omap_hsmmc_init(controllers);
- for (c = controllers; c->mmc; c++) {
- /* pdev can be null if CONFIG_MMC_OMAP_HS is not set */
- if (!c->pdev)
- continue;
- omap4_twl6030_hsmmc_set_late_init(&c->pdev->dev);
- }
-
- return 0;
-}
-#else
-int __init omap4_twl6030_hsmmc_init(struct omap2_hsmmc_info *controllers)
-{
- return 0;
-}
-#endif
extern u32 omap4_prm_vcvp_rmw(u32 mask, u32 bits, u8 offset);
#if defined(CONFIG_ARCH_OMAP4) || defined(CONFIG_SOC_OMAP5) || \
- defined(CONFIG_SOC_DRA7XX)
+ defined(CONFIG_SOC_DRA7XX) || defined(CONFIG_SOC_AM43XX)
void omap44xx_prm_reconfigure_io_chain(void);
#else
static inline void omap44xx_prm_reconfigure_io_chain(void)
static int twl_direction_out(struct gpio_chip *chip, unsigned offset, int value)
{
struct gpio_twl4030_priv *priv = to_gpio_twl4030(chip);
+ int ret = -EINVAL;
mutex_lock(&priv->mutex);
if (offset < TWL4030_GPIO_MAX)
- twl4030_set_gpio_dataout(offset, value);
+ ret = twl4030_set_gpio_direction(offset, 0);
priv->direction |= BIT(offset);
mutex_unlock(&priv->mutex);
twl_set(chip, offset, value);
- return 0;
+ return ret;
}
static int twl_to_irq(struct gpio_chip *chip, unsigned offset)
static int gpio_twl4030_remove(struct platform_device *pdev);
-static struct twl4030_gpio_platform_data *of_gpio_twl4030(struct device *dev)
+static struct twl4030_gpio_platform_data *of_gpio_twl4030(struct device *dev,
+ struct twl4030_gpio_platform_data *pdata)
{
struct twl4030_gpio_platform_data *omap_twl_info;
if (!omap_twl_info)
return NULL;
+ if (pdata)
+ *omap_twl_info = *pdata;
+
omap_twl_info->use_leds = of_property_read_bool(dev->of_node,
"ti,use-leds");
mutex_init(&priv->mutex);
if (node)
- pdata = of_gpio_twl4030(&pdev->dev);
+ pdata = of_gpio_twl4030(&pdev->dev, pdata);
if (pdata == NULL) {
dev_err(&pdev->dev, "Platform data is missing\n");
};
#ifdef CONFIG_OF
+static struct omap_i2c_bus_platform_data omap2420_pdata = {
+ .rev = OMAP_I2C_IP_VERSION_1,
+ .flags = OMAP_I2C_FLAG_NO_FIFO |
+ OMAP_I2C_FLAG_SIMPLE_CLOCK |
+ OMAP_I2C_FLAG_16BIT_DATA_REG |
+ OMAP_I2C_FLAG_BUS_SHIFT_2,
+};
+
+static struct omap_i2c_bus_platform_data omap2430_pdata = {
+ .rev = OMAP_I2C_IP_VERSION_1,
+ .flags = OMAP_I2C_FLAG_BUS_SHIFT_2 |
+ OMAP_I2C_FLAG_FORCE_19200_INT_CLK,
+};
+
static struct omap_i2c_bus_platform_data omap3_pdata = {
.rev = OMAP_I2C_IP_VERSION_1,
.flags = OMAP_I2C_FLAG_BUS_SHIFT_2,
.compatible = "ti,omap3-i2c",
.data = &omap3_pdata,
},
+ {
+ .compatible = "ti,omap2430-i2c",
+ .data = &omap2430_pdata,
+ },
+ {
+ .compatible = "ti,omap2420-i2c",
+ .data = &omap2420_pdata,
+ },
{ },
};
MODULE_DEVICE_TABLE(of, omap_i2c_of_match);
projects / ~andy / linux / commitdiff