Required properties:
- compatible : should be : "ti,tca6507".
+- #address-cells: must be 1
+- #size-cells: must be 0
+- reg: typically 0x45.
+
+Optional properties:
+- gpio-controller: allows lines to be used as output-only GPIOs.
+- #gpio-cells: if present, must be 0.
Each led is represented as a sub-node of the ti,tca6507 device.
- reg : number of LED line (could be from 0 to 6)
- linux,default-trigger : (optional)
see Documentation/devicetree/bindings/leds/common.txt
+- compatible: either "led" (the default) or "gpio".
Examples:
#size-cells = <0>;
reg = <0x45>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
led0: red-aux@0 {
label = "red:aux";
reg = <0x0>;
reg = <0x5>;
linux,default-trigger = "default-on";
};
+
+ wifi-reset@6 {
+ reg = <0x6>;
+ compatible = "gpio";
+ };
};
run_engine : Start program which is loaded via the firmware interface
firmware : Load program data
+In case of LP5523, one more command is required, 'enginex_leds'.
+It is used for selecting LED output(s) at each engine number.
+In more details, please refer to 'leds-lp5523.txt'.
+
For example, run blinking pattern in engine #1 of LP5521
echo 1 > /sys/bus/i2c/devices/xxxx/select_engine
echo 1 > /sys/class/firmware/lp5521/loading
echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
For example, run blinking pattern in engine #3 of LP55231
+Two LEDs are configured as pattern output channels.
echo 3 > /sys/bus/i2c/devices/xxxx/select_engine
echo 1 > /sys/class/firmware/lp55231/loading
echo "9d0740ff7e0040007e00a0010000" > /sys/class/firmware/lp55231/data
echo 0 > /sys/class/firmware/lp55231/loading
+echo "000001100" > /sys/bus/i2c/devices/xxxx/engine3_leds
echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
To start blinking patterns in engine #2 and #3 simultaneously,
echo 1 > /sys/class/leds/red/device/run_engine
Here is another example for LP5523.
+Full LED strings are selected by 'engine2_leds'.
echo 2 > /sys/bus/i2c/devices/xxxx/select_engine
echo 1 > /sys/class/firmware/lp5523/loading
echo "9d80400004ff05ff437f0000" > /sys/class/firmware/lp5523/data
echo 0 > /sys/class/firmware/lp5523/loading
+echo "111111111" > /sys/bus/i2c/devices/xxxx/engine2_leds
echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
As soon as 'loading' is set to 0, registered callback is called.
Inside the callback, the selected engine is loaded and memory is updated.
To run programmed pattern, 'run_engine' attribute should be enabled.
-The pattern sqeuence of LP8501 is same as LP5523.
+The pattern sqeuence of LP8501 is similar to LP5523.
However pattern data is specific.
Ex 1) Engine 1 is used
echo 1 > /sys/bus/i2c/devices/xxxx/select_engine
{
.id = MC13783_LED_R1,
.name = "coreboard-led-4:red",
- .max_current = 2,
},
{
.id = MC13783_LED_G1,
.name = "coreboard-led-4:green",
- .max_current = 2,
},
{
.id = MC13783_LED_B1,
.name = "coreboard-led-4:blue",
- .max_current = 2,
},
{
.id = MC13783_LED_R2,
.name = "coreboard-led-5:red",
- .max_current = 3,
},
{
.id = MC13783_LED_G2,
.name = "coreboard-led-5:green",
- .max_current = 3,
},
{
.id = MC13783_LED_B2,
.name = "coreboard-led-5:blue",
- .max_current = 3,
},
};
.led_control[0] = MC13783_LED_C0_ENABLE | MC13783_LED_C0_ABMODE(0),
.led_control[1] = MC13783_LED_C1_SLEWLIM,
.led_control[2] = MC13783_LED_C2_SLEWLIM,
- .led_control[3] = MC13783_LED_C3_PERIOD(0),
- .led_control[4] = MC13783_LED_C3_PERIOD(0),
+ .led_control[3] = MC13783_LED_C3_PERIOD(0) |
+ MC13783_LED_C3_CURRENT_R1(2) |
+ MC13783_LED_C3_CURRENT_G1(2) |
+ MC13783_LED_C3_CURRENT_B1(2),
+ .led_control[4] = MC13783_LED_C4_PERIOD(0) |
+ MC13783_LED_C4_CURRENT_R2(3) |
+ MC13783_LED_C4_CURRENT_G2(3) |
+ MC13783_LED_C4_CURRENT_B2(3),
};
static struct mc13xxx_buttons_platform_data moboard_buttons = {
void led_trigger_event(struct led_trigger *trig,
enum led_brightness brightness)
{
- struct list_head *entry;
+ struct led_classdev *led_cdev;
if (!trig)
return;
read_lock(&trig->leddev_list_lock);
- list_for_each(entry, &trig->led_cdevs) {
- struct led_classdev *led_cdev;
-
- led_cdev = list_entry(entry, struct led_classdev, trig_list);
+ list_for_each_entry(led_cdev, &trig->led_cdevs, trig_list)
led_set_brightness(led_cdev, brightness);
- }
read_unlock(&trig->leddev_list_lock);
}
EXPORT_SYMBOL_GPL(led_trigger_event);
int oneshot,
int invert)
{
- struct list_head *entry;
+ struct led_classdev *led_cdev;
if (!trig)
return;
read_lock(&trig->leddev_list_lock);
- list_for_each(entry, &trig->led_cdevs) {
- struct led_classdev *led_cdev;
-
- led_cdev = list_entry(entry, struct led_classdev, trig_list);
+ list_for_each_entry(led_cdev, &trig->led_cdevs, trig_list) {
if (oneshot)
led_blink_set_oneshot(led_cdev, delay_on, delay_off,
invert);
lp5521_wait_opmode_done();
}
-static void lp5521_stop_engine(struct lp55xx_chip *chip)
+static void lp5521_stop_all_engines(struct lp55xx_chip *chip)
{
lp55xx_write(chip, LP5521_REG_OP_MODE, 0);
lp5521_wait_opmode_done();
}
+static void lp5521_stop_engine(struct lp55xx_chip *chip)
+{
+ enum lp55xx_engine_index idx = chip->engine_idx;
+ u8 mask[] = {
+ [LP55XX_ENGINE_1] = LP5521_MODE_R_M,
+ [LP55XX_ENGINE_2] = LP5521_MODE_G_M,
+ [LP55XX_ENGINE_3] = LP5521_MODE_B_M,
+ };
+
+ lp55xx_update_bits(chip, LP5521_REG_OP_MODE, mask[idx], 0);
+
+ lp5521_wait_opmode_done();
+}
+
static void lp5521_run_engine(struct lp55xx_chip *chip, bool start)
{
int ret;
struct lp55xx_led *led = i2c_get_clientdata(client);
struct lp55xx_chip *chip = led->chip;
- lp5521_stop_engine(chip);
+ lp5521_stop_all_engines(chip);
lp55xx_unregister_sysfs(chip);
lp55xx_unregister_leds(led, chip);
lp55xx_deinit_device(chip);
lp55xx_write(chip, LP5523_REG_PROG_PAGE_SEL, page_sel[idx]);
}
-static void lp5523_stop_engine(struct lp55xx_chip *chip)
+static void lp5523_stop_all_engines(struct lp55xx_chip *chip)
{
lp55xx_write(chip, LP5523_REG_OP_MODE, 0);
lp5523_wait_opmode_done();
}
+static void lp5523_stop_engine(struct lp55xx_chip *chip)
+{
+ enum lp55xx_engine_index idx = chip->engine_idx;
+ u8 mask[] = {
+ [LP55XX_ENGINE_1] = LP5523_MODE_ENG1_M,
+ [LP55XX_ENGINE_2] = LP5523_MODE_ENG2_M,
+ [LP55XX_ENGINE_3] = LP5523_MODE_ENG3_M,
+ };
+
+ lp55xx_update_bits(chip, LP5523_REG_OP_MODE, mask[idx], 0);
+
+ lp5523_wait_opmode_done();
+}
+
static void lp5523_turn_off_channels(struct lp55xx_chip *chip)
{
int i;
}
out:
- lp5523_stop_engine(chip);
+ lp5523_stop_all_engines(chip);
return ret;
}
struct lp55xx_led *led = i2c_get_clientdata(client);
struct lp55xx_chip *chip = led->chip;
- lp5523_stop_engine(chip);
+ lp5523_stop_all_engines(chip);
lp55xx_unregister_sysfs(chip);
lp55xx_unregister_leds(led, chip);
lp55xx_deinit_device(chip);
{
struct lp55xx_chip *chip = context;
struct device *dev = &chip->cl->dev;
+ enum lp55xx_engine_index idx = chip->engine_idx;
if (!fw) {
dev_err(dev, "firmware request failed\n");
/* handling firmware data is chip dependent */
mutex_lock(&chip->lock);
+ chip->engines[idx - 1].mode = LP55XX_ENGINE_LOAD;
chip->fw = fw;
if (chip->cfg->firmware_cb)
chip->cfg->firmware_cb(chip);
BUG();
}
- mc13xxx_lock(led->master);
mc13xxx_reg_rmw(led->master, reg, mask << shift, value << shift);
- mc13xxx_unlock(led->master);
}
static void mc13xxx_led_set(struct led_classdev *led_cdev,
schedule_work(&led->work);
}
-static int __init mc13xxx_led_setup(struct mc13xxx_led *led, int max_current)
-{
- int shift, mask, reg, ret, bank;
-
- switch (led->id) {
- case MC13783_LED_MD:
- reg = MC13XXX_REG_LED_CONTROL(2);
- shift = 0;
- mask = 0x07;
- break;
- case MC13783_LED_AD:
- reg = MC13XXX_REG_LED_CONTROL(2);
- shift = 3;
- mask = 0x07;
- break;
- case MC13783_LED_KP:
- reg = MC13XXX_REG_LED_CONTROL(2);
- shift = 6;
- mask = 0x07;
- break;
- case MC13783_LED_R1:
- case MC13783_LED_G1:
- case MC13783_LED_B1:
- case MC13783_LED_R2:
- case MC13783_LED_G2:
- case MC13783_LED_B2:
- case MC13783_LED_R3:
- case MC13783_LED_G3:
- case MC13783_LED_B3:
- bank = (led->id - MC13783_LED_R1) / 3;
- reg = MC13XXX_REG_LED_CONTROL(3) + bank;
- shift = ((led->id - MC13783_LED_R1) - bank * 3) * 2;
- mask = 0x03;
- break;
- case MC13892_LED_MD:
- reg = MC13XXX_REG_LED_CONTROL(0);
- shift = 9;
- mask = 0x07;
- break;
- case MC13892_LED_AD:
- reg = MC13XXX_REG_LED_CONTROL(0);
- shift = 21;
- mask = 0x07;
- break;
- case MC13892_LED_KP:
- reg = MC13XXX_REG_LED_CONTROL(1);
- shift = 9;
- mask = 0x07;
- break;
- case MC13892_LED_R:
- case MC13892_LED_G:
- case MC13892_LED_B:
- bank = (led->id - MC13892_LED_R) / 2;
- reg = MC13XXX_REG_LED_CONTROL(2) + bank;
- shift = ((led->id - MC13892_LED_R) - bank * 2) * 12 + 9;
- mask = 0x07;
- break;
- default:
- BUG();
- }
-
- mc13xxx_lock(led->master);
- ret = mc13xxx_reg_rmw(led->master, reg, mask << shift,
- max_current << shift);
- mc13xxx_unlock(led->master);
-
- return ret;
-}
-
static int __init mc13xxx_led_probe(struct platform_device *pdev)
{
struct mc13xxx_leds_platform_data *pdata = dev_get_platdata(&pdev->dev);
leds->num_leds = num_leds;
platform_set_drvdata(pdev, leds);
- mc13xxx_lock(mcdev);
for (i = 0; i < devtype->num_regs; i++) {
reg = pdata->led_control[i];
WARN_ON(reg >= (1 << 24));
ret = mc13xxx_reg_write(mcdev, MC13XXX_REG_LED_CONTROL(i), reg);
if (ret)
- break;
- }
- mc13xxx_unlock(mcdev);
-
- if (ret) {
- dev_err(&pdev->dev, "Unable to init LED driver\n");
- return ret;
+ return ret;
}
for (i = 0; i < num_leds; i++) {
const char *name, *trig;
- char max_current;
ret = -EINVAL;
id = pdata->led[i].id;
name = pdata->led[i].name;
trig = pdata->led[i].default_trigger;
- max_current = pdata->led[i].max_current;
if ((id > devtype->led_max) || (id < devtype->led_min)) {
dev_err(&pdev->dev, "Invalid ID %i\n", id);
INIT_WORK(&leds->led[i].work, mc13xxx_led_work);
- ret = mc13xxx_led_setup(&leds->led[i], max_current);
- if (ret) {
- dev_err(&pdev->dev, "Unable to setup LED %i\n", id);
- break;
- }
ret = led_classdev_register(pdev->dev.parent,
&leds->led[i].cdev);
if (ret) {
cancel_work_sync(&leds->led[i].work);
}
- mc13xxx_lock(mcdev);
for (i = 0; i < leds->devtype->num_regs; i++)
mc13xxx_reg_write(mcdev, MC13XXX_REG_LED_CONTROL(i), 0);
- mc13xxx_unlock(mcdev);
return 0;
}
struct led_pwm_data *led_dat =
container_of(led_cdev, struct led_pwm_data, cdev);
unsigned int max = led_dat->cdev.max_brightness;
- unsigned int period = led_dat->period;
+ unsigned long long duty = led_dat->period;
- led_dat->duty = brightness * period / max;
+ duty *= brightness;
+ do_div(duty, max);
+ led_dat->duty = duty;
if (led_dat->can_sleep)
schedule_work(&led_dat->work);
static int led_pwm_create_of(struct platform_device *pdev,
struct led_pwm_priv *priv)
{
- struct device_node *node = pdev->dev.of_node;
struct device_node *child;
int ret;
- for_each_child_of_node(node, child) {
+ for_each_child_of_node(pdev->dev.of_node, child) {
struct led_pwm_data *led_dat = &priv->leds[priv->num_leds];
led_dat->cdev.name = of_get_property(child, "label",
#include <linux/gpio.h>
#include <linux/slab.h>
#include <linux/module.h>
+#include <linux/platform_data/leds-s3c24xx.h>
-#include <mach/hardware.h>
#include <mach/regs-gpio.h>
#include <plat/gpio-cfg.h>
-#include <linux/platform_data/leds-s3c24xx.h>
/* our context */
* The TCA6507 is a programmable LED controller that can drive 7
* separate lines either by holding them low, or by pulsing them
* with modulated width.
- * The modulation can be varied in a simple pattern to produce a blink or
- * double-blink.
+ * The modulation can be varied in a simple pattern to produce a
+ * blink or double-blink.
*
- * This driver can configure each line either as a 'GPIO' which is out-only
- * (no pull-up) or as an LED with variable brightness and hardware-assisted
- * blinking.
+ * This driver can configure each line either as a 'GPIO' which is
+ * out-only (pull-up resistor required) or as an LED with variable
+ * brightness and hardware-assisted blinking.
*
- * Apart from OFF and ON there are three programmable brightness levels which
- * can be programmed from 0 to 15 and indicate how many 500usec intervals in
- * each 8msec that the led is 'on'. The levels are named MASTER, BANK0 and
- * BANK1.
+ * Apart from OFF and ON there are three programmable brightness
+ * levels which can be programmed from 0 to 15 and indicate how many
+ * 500usec intervals in each 8msec that the led is 'on'. The levels
+ * are named MASTER, BANK0 and BANK1.
*
- * There are two different blink rates that can be programmed, each with
- * separate time for rise, on, fall, off and second-off. Thus if 3 or more
- * different non-trivial rates are required, software must be used for the extra
- * rates. The two different blink rates must align with the two levels BANK0 and
- * BANK1.
- * This driver does not support double-blink so 'second-off' always matches
- * 'off'.
+ * There are two different blink rates that can be programmed, each
+ * with separate time for rise, on, fall, off and second-off. Thus if
+ * 3 or more different non-trivial rates are required, software must
+ * be used for the extra rates. The two different blink rates must
+ * align with the two levels BANK0 and BANK1. This driver does not
+ * support double-blink so 'second-off' always matches 'off'.
*
- * Only 16 different times can be programmed in a roughly logarithmic scale from
- * 64ms to 16320ms. To be precise the possible times are:
+ * Only 16 different times can be programmed in a roughly logarithmic
+ * scale from 64ms to 16320ms. To be precise the possible times are:
* 0, 64, 128, 192, 256, 384, 512, 768,
* 1024, 1536, 2048, 3072, 4096, 5760, 8128, 16320
*
- * Times that cannot be closely matched with these must be
- * handled in software. This driver allows 12.5% error in matching.
+ * Times that cannot be closely matched with these must be handled in
+ * software. This driver allows 12.5% error in matching.
*
- * This driver does not allow rise/fall rates to be set explicitly. When trying
- * to match a given 'on' or 'off' period, an appropriate pair of 'change' and
- * 'hold' times are chosen to get a close match. If the target delay is even,
- * the 'change' number will be the smaller; if odd, the 'hold' number will be
- * the smaller.
-
- * Choosing pairs of delays with 12.5% errors allows us to match delays in the
- * ranges: 56-72, 112-144, 168-216, 224-27504, 28560-36720.
- * 26% of the achievable sums can be matched by multiple pairings. For example
- * 1536 == 1536+0, 1024+512, or 768+768. This driver will always choose the
- * pairing with the least maximum - 768+768 in this case. Other pairings are
- * not available.
+ * This driver does not allow rise/fall rates to be set explicitly.
+ * When trying to match a given 'on' or 'off' period, an appropriate
+ * pair of 'change' and 'hold' times are chosen to get a close match.
+ * If the target delay is even, the 'change' number will be the
+ * smaller; if odd, the 'hold' number will be the smaller.
+
+ * Choosing pairs of delays with 12.5% errors allows us to match
+ * delays in the ranges: 56-72, 112-144, 168-216, 224-27504,
+ * 28560-36720.
+ * 26% of the achievable sums can be matched by multiple pairings.
+ * For example 1536 == 1536+0, 1024+512, or 768+768.
+ * This driver will always choose the pairing with the least
+ * maximum - 768+768 in this case. Other pairings are not available.
*
- * Access to the 3 levels and 2 blinks are on a first-come, first-served basis.
- * Access can be shared by multiple leds if they have the same level and
- * either same blink rates, or some don't blink.
- * When a led changes, it relinquishes access and tries again, so it might
- * lose access to hardware blink.
- * If a blink engine cannot be allocated, software blink is used.
- * If the desired brightness cannot be allocated, the closest available non-zero
- * brightness is used. As 'full' is always available, the worst case would be
- * to have two different blink rates at '1', with Max at '2', then other leds
- * will have to choose between '2' and '16'. Hopefully this is not likely.
+ * Access to the 3 levels and 2 blinks are on a first-come,
+ * first-served basis. Access can be shared by multiple leds if they
+ * have the same level and either same blink rates, or some don't
+ * blink. When a led changes, it relinquishes access and tries again,
+ * so it might lose access to hardware blink.
*
- * Each bank (BANK0 and BANK1) has two usage counts - LEDs using the brightness
- * and LEDs using the blink. It can only be reprogrammed when the appropriate
- * counter is zero. The MASTER level has a single usage count.
+ * If a blink engine cannot be allocated, software blink is used. If
+ * the desired brightness cannot be allocated, the closest available
+ * non-zero brightness is used. As 'full' is always available, the
+ * worst case would be to have two different blink rates at '1', with
+ * Max at '2', then other leds will have to choose between '2' and
+ * '16'. Hopefully this is not likely.
*
- * Each Led has programmable 'on' and 'off' time as milliseconds. With each
- * there is a flag saying if it was explicitly requested or defaulted.
- * Similarly the banks know if each time was explicit or a default. Defaults
- * are permitted to be changed freely - they are not recognised when matching.
+ * Each bank (BANK0 and BANK1) has two usage counts - LEDs using the
+ * brightness and LEDs using the blink. It can only be reprogrammed
+ * when the appropriate counter is zero. The MASTER level has a
+ * single usage count.
*
+ * Each LED has programmable 'on' and 'off' time as milliseconds.
+ * With each there is a flag saying if it was explicitly requested or
+ * defaulted. Similarly the banks know if each time was explicit or a
+ * default. Defaults are permitted to be changed freely - they are
+ * not recognised when matching.
*
- * An led-tca6507 device must be provided with platform data. This data
- * lists for each output: the name, default trigger, and whether the signal
- * is being used as a GPiO rather than an led. 'struct led_plaform_data'
- * is used for this. If 'name' is NULL, the output isn't used. If 'flags'
- * is TCA6507_MAKE_CPIO, the output is a GPO.
- * The "struct led_platform_data" can be embedded in a
- * "struct tca6507_platform_data" which adds a 'gpio_base' for the GPiOs,
- * and a 'setup' callback which is called once the GPiOs are available.
*
+ * An led-tca6507 device must be provided with platform data or
+ * configured via devicetree.
+ *
+ * The platform-data lists for each output: the name, default trigger,
+ * and whether the signal is being used as a GPIO rather than an LED.
+ * 'struct led_plaform_data' is used for this. If 'name' is NULL, the
+ * output isn't used. If 'flags' is TCA6507_MAKE_GPIO, the output is
+ * a GPO. The "struct led_platform_data" can be embedded in a "struct
+ * tca6507_platform_data" which adds a 'gpio_base' for the GPIOs, and
+ * a 'setup' callback which is called once the GPIOs are available.
+ *
+ * When configured via devicetree there is one child for each output.
+ * The "reg" determines the output number and "compatible" determines
+ * whether it is an LED or a GPIO. "linux,default-trigger" can set a
+ * default trigger.
*/
#include <linux/module.h>
static int choose_times(int msec, int *c1p, int *c2p)
{
/*
- * Choose two timecodes which add to 'msec' as near as possible.
- * The first returned is the 'on' or 'off' time. The second is to be
- * used as a 'fade-on' or 'fade-off' time. If 'msec' is even,
- * the first will not be smaller than the second. If 'msec' is odd,
- * the first will not be larger than the second.
- * If we cannot get a sum within 1/8 of 'msec' fail with -EINVAL,
- * otherwise return the sum that was achieved, plus 1 if the first is
- * smaller.
- * If two possibilities are equally good (e.g. 512+0, 256+256), choose
- * the first pair so there is more change-time visible (i.e. it is
- * softer).
+ * Choose two timecodes which add to 'msec' as near as
+ * possible. The first returned is the 'on' or 'off' time.
+ * The second is to be used as a 'fade-on' or 'fade-off' time.
+ * If 'msec' is even, the first will not be smaller than the
+ * second. If 'msec' is odd, the first will not be larger
+ * than the second.
+ * If we cannot get a sum within 1/8 of 'msec' fail with
+ * -EINVAL, otherwise return the sum that was achieved, plus 1
+ * if the first is smaller.
+ * If two possibilities are equally good (e.g. 512+0,
+ * 256+256), choose the first pair so there is more
+ * change-time visible (i.e. it is softer).
*/
int c1, c2;
int tmax = msec * 9 / 8;
}
/*
- * Update the register file with the appropriate 3-bit state for
- * the given led.
+ * Update the register file with the appropriate 3-bit state for the
+ * given led.
*/
static void set_select(struct tca6507_chip *tca, int led, int val)
{
}
}
-/* Update the register file with the appropriate 4-bit code for
- * one bank or other. This can be used for timers, for levels, or
- * for initialisation.
+/* Update the register file with the appropriate 4-bit code for one
+ * bank or other. This can be used for timers, for levels, or for
+ * initialization.
*/
static void set_code(struct tca6507_chip *tca, int reg, int bank, int new)
{
tca->bank[bank].level = level;
}
-/* Record all relevant time code for a given bank */
+/* Record all relevant time codes for a given bank */
static void set_times(struct tca6507_chip *tca, int bank)
{
int c1, c2;
result = choose_times(tca->bank[bank].ontime, &c1, &c2);
dev_dbg(&tca->client->dev,
- "Chose on times %d(%d) %d(%d) for %dms\n", c1, time_codes[c1],
+ "Chose on times %d(%d) %d(%d) for %dms\n",
+ c1, time_codes[c1],
c2, time_codes[c2], tca->bank[bank].ontime);
set_code(tca, TCA6507_FADE_ON, bank, c2);
set_code(tca, TCA6507_FULL_ON, bank, c1);
result = choose_times(tca->bank[bank].offtime, &c1, &c2);
dev_dbg(&tca->client->dev,
- "Chose off times %d(%d) %d(%d) for %dms\n", c1, time_codes[c1],
+ "Chose off times %d(%d) %d(%d) for %dms\n",
+ c1, time_codes[c1],
c2, time_codes[c2], tca->bank[bank].offtime);
set_code(tca, TCA6507_FADE_OFF, bank, c2);
set_code(tca, TCA6507_FIRST_OFF, bank, c1);
static int led_prepare(struct tca6507_led *led)
{
- /* Assign this led to a bank, configuring that bank if necessary. */
+ /* Assign this led to a bank, configuring that bank if
+ * necessary. */
int level = TO_LEVEL(led->led_cdev.brightness);
struct tca6507_chip *tca = led->chip;
int c1, c2;
if (led->ontime == 0 || led->offtime == 0) {
/*
- * Just set the brightness, choosing first usable bank.
- * If none perfect, choose best.
- * Count backwards so we check MASTER bank first
- * to avoid wasting a timer.
+ * Just set the brightness, choosing first usable
+ * bank. If none perfect, choose best. Count
+ * backwards so we check MASTER bank first to avoid
+ * wasting a timer.
*/
int best = -1;/* full-on */
int diff = 15-level;
}
/*
- * We have on/off time so we need to try to allocate a timing bank.
- * First check if times are compatible with hardware and give up if
- * not.
+ * We have on/off time so we need to try to allocate a timing
+ * bank. First check if times are compatible with hardware
+ * and give up if not.
*/
if (choose_times(led->ontime, &c1, &c2) < 0)
return -EINVAL;
err = led_prepare(led);
if (err) {
/*
- * Can only fail on timer setup. In that case we need to
- * re-establish as steady level.
+ * Can only fail on timer setup. In that case we need
+ * to re-establish as steady level.
*/
led->ontime = 0;
led->offtime = 0;
spin_lock_irqsave(&tca->lock, flags);
/*
- * 'OFF' is floating high, and 'ON' is pulled down, so it has the
- * inverse sense of 'val'.
+ * 'OFF' is floating high, and 'ON' is pulled down, so it has
+ * the inverse sense of 'val'.
*/
set_select(tca, tca->gpio_map[offset],
val ? TCA6507_LS_LED_OFF : TCA6507_LS_LED_ON);
tca->gpio.direction_output = tca6507_gpio_direction_output;
tca->gpio.set = tca6507_gpio_set_value;
tca->gpio.dev = &client->dev;
+#ifdef CONFIG_OF_GPIO
+ tca->gpio.of_node = of_node_get(client->dev.of_node);
+#endif
err = gpiochip_add(&tca->gpio);
if (err) {
tca->gpio.ngpio = 0;
return ERR_PTR(-ENODEV);
tca_leds = devm_kzalloc(&client->dev,
- sizeof(struct led_info) * count, GFP_KERNEL);
+ sizeof(struct led_info) * NUM_LEDS, GFP_KERNEL);
if (!tca_leds)
return ERR_PTR(-ENOMEM);
of_get_property(child, "label", NULL) ? : child->name;
led.default_trigger =
of_get_property(child, "linux,default-trigger", NULL);
-
+ led.flags = 0;
+ if (of_property_match_string(child, "compatible", "gpio") >= 0)
+ led.flags |= TCA6507_MAKE_GPIO;
ret = of_property_read_u32(child, "reg", ®);
- if (ret != 0)
+ if (ret != 0 || reg < 0 || reg >= NUM_LEDS)
continue;
tca_leds[reg] = led;
return ERR_PTR(-ENOMEM);
pdata->leds.leds = tca_leds;
- pdata->leds.num_leds = count;
-
+ pdata->leds.num_leds = NUM_LEDS;
+#ifdef CONFIG_GPIOLIB
+ pdata->gpio_base = -1;
+#endif
return pdata;
}
int id;
const char *name;
const char *default_trigger;
-
-/* Three or two bits current selection depending on the led */
- char max_current;
};
#define MAX_LED_CONTROL_REGS 6
struct mc13xxx_led_platform_data *led;
int num_leds;
-/* LED Control 0 */
+/* MC13783 LED Control 0 */
#define MC13783_LED_C0_ENABLE (1 << 0)
#define MC13783_LED_C0_TRIODE_MD (1 << 7)
#define MC13783_LED_C0_TRIODE_AD (1 << 8)
#define MC13783_LED_C0_BOOST (1 << 10)
#define MC13783_LED_C0_ABMODE(x) (((x) & 0x7) << 11)
#define MC13783_LED_C0_ABREF(x) (((x) & 0x3) << 14)
-/* LED Control 1 */
+/* MC13783 LED Control 1 */
#define MC13783_LED_C1_TC1HALF (1 << 18)
#define MC13783_LED_C1_SLEWLIM (1 << 23)
-/* LED Control 2 */
+/* MC13783 LED Control 2 */
+#define MC13783_LED_C2_CURRENT_MD(x) (((x) & 0x7) << 0)
+#define MC13783_LED_C2_CURRENT_AD(x) (((x) & 0x7) << 3)
+#define MC13783_LED_C2_CURRENT_KP(x) (((x) & 0x7) << 6)
#define MC13783_LED_C2_PERIOD(x) (((x) & 0x3) << 21)
#define MC13783_LED_C2_SLEWLIM (1 << 23)
-/* LED Control 3 */
+/* MC13783 LED Control 3 */
+#define MC13783_LED_C3_CURRENT_R1(x) (((x) & 0x3) << 0)
+#define MC13783_LED_C3_CURRENT_G1(x) (((x) & 0x3) << 2)
+#define MC13783_LED_C3_CURRENT_B1(x) (((x) & 0x3) << 4)
#define MC13783_LED_C3_PERIOD(x) (((x) & 0x3) << 21)
#define MC13783_LED_C3_TRIODE_TC1 (1 << 23)
-/* LED Control 4 */
+/* MC13783 LED Control 4 */
+#define MC13783_LED_C4_CURRENT_R2(x) (((x) & 0x3) << 0)
+#define MC13783_LED_C4_CURRENT_G2(x) (((x) & 0x3) << 2)
+#define MC13783_LED_C4_CURRENT_B2(x) (((x) & 0x3) << 4)
#define MC13783_LED_C4_PERIOD(x) (((x) & 0x3) << 21)
#define MC13783_LED_C4_TRIODE_TC2 (1 << 23)
-/* LED Control 5 */
+/* MC13783 LED Control 5 */
+#define MC13783_LED_C5_CURRENT_R3(x) (((x) & 0x3) << 0)
+#define MC13783_LED_C5_CURRENT_G3(x) (((x) & 0x3) << 2)
+#define MC13783_LED_C5_CURRENT_B3(x) (((x) & 0x3) << 4)
#define MC13783_LED_C5_PERIOD(x) (((x) & 0x3) << 21)
#define MC13783_LED_C5_TRIODE_TC3 (1 << 23)
+/* MC13892 LED Control 0 */
+#define MC13892_LED_C0_CURRENT_MD(x) (((x) & 0x7) << 9)
+#define MC13892_LED_C0_CURRENT_AD(x) (((x) & 0x7) << 21)
+/* MC13892 LED Control 1 */
+#define MC13892_LED_C1_CURRENT_KP(x) (((x) & 0x7) << 9)
+/* MC13892 LED Control 2 */
+#define MC13892_LED_C2_CURRENT_R(x) (((x) & 0x7) << 9)
+#define MC13892_LED_C2_CURRENT_G(x) (((x) & 0x7) << 21)
+/* MC13892 LED Control 3 */
+#define MC13892_LED_C3_CURRENT_B(x) (((x) & 0x7) << 9)
u32 led_control[MAX_LED_CONTROL_REGS];
};
/*
- * arch/arm/mach-kirkwood/include/mach/leds-netxbig.h
- *
* Platform data structure for netxbig LED driver
*
* This file is licensed under the terms of the GNU General Public
* warranty of any kind, whether express or implied.
*/
-#ifndef __MACH_LEDS_NETXBIG_H
-#define __MACH_LEDS_NETXBIG_H
+#ifndef __LEDS_KIRKWOOD_NETXBIG_H
+#define __LEDS_KIRKWOOD_NETXBIG_H
struct netxbig_gpio_ext {
unsigned *addr;
int num_leds;
};
-#endif /* __MACH_LEDS_NETXBIG_H */
+#endif /* __LEDS_KIRKWOOD_NETXBIG_H */
/*
- * arch/arm/mach-kirkwood/include/mach/leds-ns2.h
- *
* Platform data structure for Network Space v2 LED driver
*
* This file is licensed under the terms of the GNU General Public
* warranty of any kind, whether express or implied.
*/
-#ifndef __MACH_LEDS_NS2_H
-#define __MACH_LEDS_NS2_H
+#ifndef __LEDS_KIRKWOOD_NS2_H
+#define __LEDS_KIRKWOOD_NS2_H
struct ns2_led {
const char *name;
struct ns2_led *leds;
};
-#endif /* __MACH_LEDS_NS2_H */
+#endif /* __LEDS_KIRKWOOD_NS2_H */
projects / ~andy / linux / commitdiff