Andy Whitcroft [Mon, 25 Nov 2013 16:52:34 +0000 (16:52 +0000)]
xen-netback: include definition of csum_ipv6_magic
We are now using csum_ipv6_magic, include the appropriate header.
Avoids the following error:
drivers/net/xen-netback/netback.c:1313:4: error: implicit declaration of function 'csum_ipv6_magic' [-Werror=implicit-function-declaration]
tcph->check = ~csum_ipv6_magic(&ipv6h->saddr,
Signed-off-by: Andy Whitcroft <apw@canonical.com> Acked-by: Ian Campbell <ian.campbell@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Mon, 25 Nov 2013 09:19:04 +0000 (17:19 +0800)]
macvtap: fix tx_dropped counting error
After commit 8ffab51b3dfc54876f145f15b351c41f3f703195
(macvlan: lockless tx path), tx stat counter were converted to percpu stat
structure. So we need use to this also for tx_dropped in macvtap. Otherwise, the
management won't notice the dropping packet in macvtap tx path.
Cc: Michael S. Tsirkin <mst@redhat.com> Cc: Vlad Yasevich <vyasevic@redhat.com> Cc: Eric Dumazet <edumazet@google.com> Signed-off-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Vlad Yasevich <vyasevic@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xufeng Zhang [Mon, 25 Nov 2013 03:26:57 +0000 (11:26 +0800)]
sctp: Restore 'resent' bit to avoid retransmitted chunks for RTT measurements
Currently retransmitted DATA chunks could also be used for
RTT measurements since there are no flag to identify whether
the transmitted DATA chunk is a new one or a retransmitted one.
This problem is introduced by commit ae19c5486 ("sctp: remove
'resent' bit from the chunk") which inappropriately removed the
'resent' bit completely, instead of doing this, we should set
the resent bit only for the retransmitted DATA chunks.
Signed-off-by: Xufeng Zhang <xufeng.zhang@windriver.com> Acked-by: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Sun, 24 Nov 2013 20:09:26 +0000 (21:09 +0100)]
genetlink/pmcraid: use proper genetlink multicast API
The pmcraid driver is abusing the genetlink API and is using its
family ID as the multicast group ID, which is invalid and may
belong to somebody else (and likely will.)
Make it use the correct API, but since this may already be used
as-is by userspace, reserve a family ID for this code and also
reserve that group ID to not break userspace assumptions.
My previous patch broke event delivery in the driver as I missed
that it wasn't using the right API and forgot to update it later
in my series.
While changing this, I noticed that the genetlink code could use
the static group ID instead of a strcmp(), so also do that for
the VFS_DQUOT family.
Cc: Anil Ravindranath <anil_ravindranath@pmc-sierra.com> Cc: "James E.J. Bottomley" <JBottomley@parallels.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
genetlink: Fix uninitialized variable in genl_validate_assign_mc_groups()
net/netlink/genetlink.c: In function ‘genl_validate_assign_mc_groups’:
net/netlink/genetlink.c:217: warning: ‘err’ may be used uninitialized in this
function
Commit 2a94fe48f32ccf7321450a2cc07f2b724a444e5b ("genetlink: make multicast
groups const, prevent abuse") split genl_register_mc_group() in multiple
functions, but dropped the initialization of err.
Initialize err to zero to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Guenter Roeck [Sat, 23 Nov 2013 06:07:57 +0000 (22:07 -0800)]
tg3: Convert to use hwmon_device_register_with_groups
Use new hwmon API to simplify code, provide missing mandatory 'name'
sysfs attribute, and attach hwmon attributes to hwmon device instead
of pci device.
Signed-off-by: Guenter Roeck <linux@roeck-us.net> Reviewed-by: Jean Delvare <khali@linux-fr.org> Acked-by: Nithin Nayak Sujir <nsujir@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
dingtianhong [Fri, 22 Nov 2013 14:28:43 +0000 (22:28 +0800)]
bonding: disable arp and enable mii monitoring when bond change to no uses arp mode
Because the ARP monitoring is not support for 802.3ad, but I still
could change the mode to 802.3ad from ab mode while ARP monitoring
is running, it is incorrect.
So add a check for 802.3ad in bonding_store_mode to fix the problem,
and make a new macro BOND_NO_USES_ARP() to simplify the code.
v2: according to the Dan Williams's suggestion, bond mode is the most
important bond option, it should override any of the other sub-options.
So when the mode is changed, the conficting values should be cleared
or reset, otherwise the user has to duplicate more operations to modify
the logic. I disable the arp and enable mii monitoring when the bond mode
is changed to AB, TB and 8023AD if the arp interval is true.
v3: according to the Nik's suggestion, the default value of miimon should need
a name, there is several place to use it, and the bond_store_arp_interval()
could use micro BOND_NO_USES_ARP to make the code more simpify.
Suggested-by: Dan Williams <dcbw@redhat.com> Suggested-by: Nikolay Aleksandrov <nikolay@redhat.com> Signed-off-by: Ding Tianhong <dingtianhong@huawei.com> Reviewed-by: Nikolay Aleksandrov <nikolay@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel [Thu, 28 Nov 2013 17:31:05 +0000 (18:31 +0100)]
diag: warn about missing first netlink attribute
The first netlink attribute (value 0) must always be defined as none/unspec.
This is correctly done in inet_diag.h, but other diag interfaces are wrong.
Because we cannot change an existing API, I add a comment to point the mistake
and avoid to propagate it in a new diag API in the future.
CC: Thomas Graf <tgraf@suug.ch> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Acked-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 28 Nov 2013 17:57:46 +0000 (09:57 -0800)]
Merge tag 'gpio-v3.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Here us a bunch of patches for the v3.13 series. Most important stuff
is related to fixes and documentation for the new GPIO descriptor API.
If the diffstat is scary you'll notice most of it is to
Documentation/*:
- A big slew of documentation for the gpiod transition that happened
in the merge window, no semantic effect, but we should provide
proper documentation with the new API.
- Fix flags related to the new API.
- Fix to the find_chip_by_name() lookup function related to the new
API.
- Fix of_find_gpio() when not using device tree.
- Bug fix for the TB10x direction setting.
- Error path fixes from Dan Carpenter.
- Nasty IRQdomain bug relating to taking an unitialized spinlock.
- Minor fixes here and there"
* tag 'gpio-v3.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: bcm281xx: Fix return value of bcm_kona_gpio_get()
gpio: pl061: move irqdomain initialization
gpio: ucb1400: Add MODULE_ALIAS
gpiolib: fix of_find_gpio() when OF not defined
gpio: fix memory leak in error path
gpio: rcar: NULL dereference on error in probe()
gpio: msm: make msm_gpio.summary_irq signed for error handling
gpio: mvebu: make mvchip->irqbase signed for error handling
gpiolib: use dedicated flags for GPIO properties
gpiolib: fix find_chip_by_name()
Documentation: gpiolib: document new interface
gpio: tb10x: Set output value before setting direction to output
Linus Torvalds [Thu, 28 Nov 2013 17:51:39 +0000 (09:51 -0800)]
Merge tag 'md/3.13-fixes' of git://neil.brown.name/md
Pull md fixes from Neil Brown:
"Three bug fixes for md in 3.13-rc
All recent regressions, one in 3.12 so marked for -stable"
* tag 'md/3.13-fixes' of git://neil.brown.name/md:
md/raid5: fix newly-broken locking in get_active_stripe.
md: test mddev->flags more safely in md_check_recovery.
md/raid5: fix new memory-reference bug in alloc_thread_groups.
Linus Torvalds [Thu, 28 Nov 2013 17:50:25 +0000 (09:50 -0800)]
Merge branch 'for-next' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"SMB3 "validate negotiate" is needed to prevent certain types of
downgrade attacks.
Also changes SMB2/SMB3 copy offload from using the BTRFS copy ioctl
(BTRFS_IOC_CLONE) to a cifs specific ioctl (CIFS_IOC_COPYCHUNK_FILE)
to address Christoph's comment that there are semantic differences
between requesting copy offload in which copy-on-write is mandatory
(as in the BTRFS ioctl) and optional in the SMB2/SMB3 case. Also
fixes SMB2/SMB3 copychunk for large files"
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
[CIFS] Do not use btrfs refcopy ioctl for SMB2 copy offload
Check SMB3 dialects against downgrade attacks
Removed duplicated (and unneeded) goto
CIFS: Fix SMB2/SMB3 Copy offload support (refcopy) for large files
Helge Deller [Thu, 28 Nov 2013 08:16:33 +0000 (09:16 +0100)]
kernel/extable: fix address-checks for core_kernel and init areas
The init_kernel_text() and core_kernel_text() functions should not
include the labels _einittext and _etext when checking if an address is
inside the .text or .init sections.
Mark Rutland [Thu, 28 Nov 2013 14:21:40 +0000 (14:21 +0000)]
irqchip: Gic: fix boot for chained gics
As of c0114709ed: "irqchip: gic: Perform the gic_secondary_init() call
via CPU notifier", booting on a platform with chained gics (e.g.
Realview EB ARM11MPCore) will result in the gic_cpu_notifier being
registered twice, corrupting the cpu notifier list and rendering the
platform unbootable.
This patch ensures that we only register the notifier for the first
gic, allowing platforms with chained gics to boot. At the same time we
limit the pointlessly duplicated calls to set_smp_cross_call and
set_handle_irq to the first gic registered.
Takashi Iwai [Thu, 28 Nov 2013 14:21:21 +0000 (15:21 +0100)]
ALSA: hda - Initialize missing bass speaker pin for ASUS AIO ET2700
Add a fixup entry for the missing bass speaker pin 0x16 on ASUS ET2700
AiO desktop. The channel map will be added in the next patch, so that
this can be backported easily to stable kernels.
Chew, Chiau Ee [Thu, 28 Nov 2013 18:13:11 +0000 (02:13 +0800)]
spi/pxa2xx: Restore private register bits.
The Intel LPSS SPI private register bits have to be restored
when system resume from S3 suspend.
Signed-off-by: Chew, Chiau Ee <chiau.ee.chew@intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Mark Brown <broonie@linaro.org>
Takashi Iwai [Thu, 28 Nov 2013 10:05:28 +0000 (11:05 +0100)]
ALSA: hda - Check leaf nodes to find aamix amps
The current generic parser assumes blindly that the volume and mute
amps are found in the aamix node itself. But on some codecs,
typically Analog Devices ones, the aamix amps are separately
implemented in each leaf node of the aamix node, and the current
driver can't establish the correct amp controls. This is a regression
compared with the previous static quirks.
This patch extends the search for the amps to the leaf nodes for
allowing the aamix controls again on such codecs.
In this implementation, I didn't code to loop through the whole paths,
since usually one depth should suffice, and we can't search too
deeply, as it may result in the conflicting control assignments.
Florian Meier [Mon, 25 Nov 2013 08:01:50 +0000 (09:01 +0100)]
i2c: bcm2835: Linking platform nodes to adapter nodes
In order to find I2C devices in the device tree, the platform nodes
have to be known by the I2C core. This requires setting the
dev.of_node parameter of the adapter.
Signed-off-by: Florian Meier <florian.meier@koalo.de> Tested-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Linus Torvalds [Thu, 28 Nov 2013 05:06:01 +0000 (21:06 -0800)]
Merge tag 'tty-3.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some tty/serial driver fixes for reported issues in 3.13-rc2.
The n_gsm "fix" was reverted as it was found to not be correct.
Hopefully this will be resolved in a future pull request, but as
there's really only one user of this line setting, it's not a big
deal..."
* tag 'tty-3.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "n_gsm: race between ld close and gsmtty open"
n_tty: Protect minimum_to_wake reset for concurrent readers
tty: Reset hupped state on open
TTY: amiserial, add missing platform check
TTY: pmac_zilog, check existence of ports in pmz_console_init()
n_gsm: race between ld close and gsmtty open
tty/serial/8250: fix typo in help text
n_tty: Fix 4096-byte canonical reads
n_tty: Fix echo overrun tail computation
n_tty: Ensure reader restarts worker for next reader
Linus Torvalds [Thu, 28 Nov 2013 05:05:31 +0000 (21:05 -0800)]
Merge tag 'staging-3.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging fixes from Greg KH:
"Here are a number of staging, and IIO driver, fixes for 3.13-rc2 that
resolve issues that have been reported for 3.13-rc1. All of these
have been in linux-next for a bit this week"
* tag 'staging-3.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (25 commits)
Staging: tidspbridge: disable driver
staging: zsmalloc: Ensure handle is never 0 on success
staging/lustre/ptlrpc: fix ptlrpc_stop_pinger logic
staging: r8188eu: Fix AP mode
Staging: btmtk_usb: Add hdev parameter to hdev->send driver callback
Staging: go7007: fix up some remaining go->dev issues
staging: imx-drm: Fix modular build of DRM_IMX_IPUV3
staging: ft1000: fix use of potentially uninitialized variable
Revert "staging:media: Use dev_dbg() instead of pr_debug()"
Staging: zram: Fix memory leak by refcount mismatch
staging: vt6656: [BUG] Fix for TX USB resets from vendors driver.
staging: nvec: potential NULL dereference on error path
Staging: vt6655-6: potential NULL dereference in hostap_disable_hostapd()
staging: comedi: s626: fix value written by s626_set_dac()
Staging: comedi: pcl730: fix some bitwise vs logical AND bugs
staging: comedi: fix potentially uninitialised variable
iio:accel:kxsd9 fix missing mutex unlock
iio: adc: ti_am335x_adc: avoid double free of buffer.
staging:iio: Fix hmc5843 Kconfig dependencies
iio: Fix tcs3472 Kconfig dependencies
...
Linus Torvalds [Thu, 28 Nov 2013 05:04:37 +0000 (21:04 -0800)]
Merge tag 'driver-core-3.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are 3 patches for sysfs issues that have been reported. Well, 1
patch really, the first one is reverted as it's not really needed (the
correct fix is coming in through the different driver subsystems
instead)
But that 1 sysfs fix is needed, so this is still a good thing to pull
in now"
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'driver-core-3.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
Revert "sysfs: handle duplicate removal attempts in sysfs_remove_group()"
sysfs: use a separate locking class for open files depending on mmap
sysfs: handle duplicate removal attempts in sysfs_remove_group()
Linus Torvalds [Thu, 28 Nov 2013 04:41:54 +0000 (20:41 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
- fix compat ioctl leak in uhid, by David Herrmann
- fix scheduling in atomic context (causing actual lockups in real
world) in hid-sony driver, by Sven Eckelmann
- revert patch introducing VID/PID conflict, by Jiri Kosina
- support from various new device IDs by Benjamin Tissoires and
KaiChung Cheng
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: uhid: fix leak for 64/32 UHID_CREATE
HID: kye: fix unresponsive keyboard
HID: kye: Add report fixup for Genius Manticore Keyboard
HID: multicouh: add PID VID to support 1 new Wistron optical touch device
HID: appleir: force input to be set
Revert "HID: wiimote: add LEGO-wiimote VID"
HID: sony: Send FF commands in non-atomic context
Linus Torvalds [Thu, 28 Nov 2013 04:40:35 +0000 (20:40 -0800)]
Merge tag 'pm+acpi-3.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
- Fix for a recent regression in the Tegra cpufreq driver causing
excess error messages to be printed from Stephen Warren
- ACPI-based device hotplug fix to prevent conflicting notify handlers
from being installed for PCI host bridge objects. From Toshi Kani
- ACPICA update to upstream version 20131115. This contains bug fixes
mostly (loop termination fix for the get AML length function, fixes
related to namespace node removal and debug output). From Bob Moore,
Tomasz Nowicki and Lv Zheng
- Removal of incorrect inclusions of internal ACPICA header files by
non-ACPICA code from Lv Zheng
- Fixes for the ACPI sysfs interface exposing tables to user space from
Daisuke Hatayama and Jeremy Compostella
- Assorted ACPI and cpufreq cleanups from Sachin Kamat and Al Stone
- cpupower tool fix and man page from Thomas Renninger
* tag 'pm+acpi-3.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: Clean up incorrect inclusions of ACPICA headers
tools: cpupower: fix wrong err msg not supported vs not available
tools: cpupower: Add cpupower-idle-set(1) manpage
ACPI / sysfs: Fix incorrect ACPI tables walk in acpi_tables_sysfs_init()
ACPI / sysfs: Set file size for each exposed ACPI table
ACPICA: Update version to 20131115.
ACPICA: Add support to delete all objects attached to the root namespace node.
ACPICA: Delete all attached data objects during namespace node deletion.
ACPICA: Resources: Fix loop termination for the get AML length function.
ACPICA: Tests: Add CHECKSUM_ABORT protection for test utilities.
ACPICA: Debug output: Do not emit function nesting level for kernel build.
ACPI / sleep: clean up compiler warning about uninitialized field
cpufreq: exynos: Remove unwanted EXPORT_SYMBOL
cpufreq: tegra: don't error target() when suspended
ACPI / hotplug: Fix conflicted PCI bridge notify handlers
Ilia Mirkin [Wed, 27 Nov 2013 17:38:42 +0000 (12:38 -0500)]
drm/nouveau/hwmon: fix compilation without CONFIG_HWMON
Reported-by: Jim Davis <jim.epost@gmail.com> Tested-by: Jim Davis <jim.epost@gmail.com> Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu> Signed-off-by: Dave Airlie <airlied@redhat.com>
David Herrmann [Tue, 26 Nov 2013 11:50:50 +0000 (12:50 +0100)]
drm/sysfs: fix OOM verification
Copy/Paste typo.. we need to test for ->kdev instead of ->dev.
Reported-by: Juha Leppänen <juha_efku@dnainternet.net> Signed-off-by: David Herrmann <dh.herrmann@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Linus Torvalds [Thu, 28 Nov 2013 04:32:38 +0000 (20:32 -0800)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc fixes from Ben Herrenschmidt:
"The main thing that caused problem was that CONFIG_CPU_LITTLE_ENDIAN
got turned on with allyesconfig and such, which is not a very good
idea especially since it requires a newer toolchain than what most
people have.
So we turned it into a choice instead that defaults to big endian"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/windfarm: Fix XServe G5 fan control Makefile issue
arch/powerpc/kernel: Use %12.12s instead of %12s to avoid memory overflow
powerpc/signals: Improved mark VSX not saved with small contexts fix
powerpc/kdump: Adding symbols in vmcoreinfo to facilitate dump filtering
powerpc: allyesconfig should not select CONFIG_CPU_LITTLE_ENDIAN
powerpc: Fix error when cross building TAGS & cscope
powerpc/booke: Only check for hugetlb in flush if vma != NULL
powerpc/85xx: typo in dts: "interupt" (four devices)
powerpc/8xx: mfspr SPRN_TBRx in lieu of mftb/mftbu is not supported
powerpc/corenet64: compile with CONFIG_E{5,6}500_CPU well
NeilBrown [Wed, 27 Nov 2013 23:55:27 +0000 (10:55 +1100)]
md/raid5: fix newly-broken locking in get_active_stripe.
commit 566c09c53455d7c4f1 raid5: relieve lock contention in get_active_stripe()
modified the locking in get_active_stripe() reducing the range
protected by the (highly contended) device_lock.
Unfortunately it reduced the range too much opening up some races.
One race can occur if get_priority_stripe runs between the
test on sh->count and device_lock being taken.
This will mean that sh->lru is not empty while get_active_stripe
thinks ->count is zero resulting in a 'BUG' firing.
Another race happens if __release_stripe is called immediately
after sh->count is tested and found to be non-zero. If STRIPE_HANDLE
is not set, get_active_stripe should increment ->active_stripes
when it increments ->count from 0, but as it didn't think it was 0,
it doesn't.
Extending device_lock to cover the test on sh->count close these
races.
While we are here, fix the two BUG tests:
-If count is zero, then lru really must not be empty, or we've
lock the stripe_head somehow - no other tests are relevant.
-STRIPE_ON_RELEASE_LIST is completely independent of ->lru so
testing it is pointless.
Reported-and-tested-by: Brassow Jonathan <jbrassow@redhat.com> Reviewed-by: Shaohua Li <shli@kernel.org> Fixes: 566c09c53455d7c4f1 Signed-off-by: NeilBrown <neilb@suse.de>
NeilBrown [Wed, 27 Nov 2013 23:34:18 +0000 (10:34 +1100)]
md: test mddev->flags more safely in md_check_recovery.
commit 7a0a5355cbc71efa md: Don't test all of mddev->flags at once.
made most tests on mddev->flags safer, but missed one.
When
commit 260fa034ef7a4ff8b7306 md: avoid deadlock when dirty buffers during md_stop.
added MD_STILL_CLOSED, this caused md_check_recovery to misbehave.
It can think there is something to do but find nothing. This can
lead to the md thread spinning during array shutdown.
https://bugzilla.kernel.org/show_bug.cgi?id=65721
Reported-and-tested-by: Richard W.M. Jones <rjones@redhat.com> Fixes: 260fa034ef7a4ff8b7306 Cc: stable@vger.kernel.org (3.12) Signed-off-by: NeilBrown <neilb@suse.de>
NeilBrown [Mon, 25 Nov 2013 00:12:43 +0000 (11:12 +1100)]
md/raid5: fix new memory-reference bug in alloc_thread_groups.
In alloc_thread_groups, worker_groups is a pointer to an array,
not an array of pointers.
So
worker_groups[i]
is wrong. It should be
&(*worker_groups)[i]
Tejun Heo [Wed, 27 Nov 2013 23:16:21 +0000 (18:16 -0500)]
cgroup: fix cgroup_subsys_state leak for seq_files
If a cgroup file implements either read_map() or read_seq_string(),
such file is served using seq_file by overriding file->f_op to
cgroup_seqfile_operations, which also overrides the release method to
single_release() from cgroup_file_release().
Because cgroup_file_open() didn't use to acquire any resources, this
used to be fine, but since f7d58818ba42 ("cgroup: pin
cgroup_subsys_state when opening a cgroupfs file"), cgroup_file_open()
pins the css (cgroup_subsys_state) which is put by
cgroup_file_release(). The patch forgot to update the release path
for seq_files and each open/release cycle leaks a css reference.
Fix it by updating cgroup_file_release() to also handle seq_files and
using it for seq_file release path too.
After commit bcdde7e221a8 (sysfs: make __sysfs_remove_dir() recursive)
Mika Westerberg sees traces analogous to the one below in Thunderbolt
hot-remove testing:
The source of this problem is that SCSI hosts are removed from
ATA ports after calling ata_tport_delete() which removes the
port's sysfs directory, among other things. Now, after commit bcdde7e221a8, the sysfs directory is removed along with all of
its subdirectories that include the SCSI host's sysfs directory
and its subdirectories at this point. Consequently, when
device_del() is finally called for any child device of the SCSI
host and tries to remove its "power" group (which is already
gone then), it triggers the above warning.
To make the warnings go away, change the removal ordering in
ata_port_detach() so that the SCSI host is removed from the
port before ata_tport_delete() is called.
References: https://bugzilla.kernel.org/show_bug.cgi?id=65281 Reported-and-tested-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Tested-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Tejun Heo <tj@kernel.org>
Which reports that we take mems_allowed_seq with interrupts enabled. A
little digging found that this can only be from
cpuset_change_task_nodemask().
This is an actual deadlock because an interrupt doing an allocation will
hit get_mems_allowed()->...->__read_seqcount_begin(), which will spin
forever waiting for the write side to complete.
Cc: John Stultz <john.stultz@linaro.org> Cc: Mel Gorman <mgorman@suse.de> Reported-by: Juri Lelli <juri.lelli@gmail.com> Signed-off-by: Peter Zijlstra <peterz@infradead.org> Tested-by: Juri Lelli <juri.lelli@gmail.com> Acked-by: Li Zefan <lizefan@huawei.com> Acked-by: Mel Gorman <mgorman@suse.de> Signed-off-by: Tejun Heo <tj@kernel.org> Cc: stable@vger.kernel.org
Victor Kamensky [Wed, 27 Nov 2013 13:48:08 +0000 (15:48 +0200)]
i2c: omap: raw read and write endian fix
All OMAP IP blocks expect LE data, but CPU may operate in BE mode.
Need to use endian neutral functions to read/write h/w registers.
I.e instead of __raw_read[lw] and __raw_write[lw] functions code
need to use read[lw]_relaxed and write[lw]_relaxed functions.
If the first simply reads/writes register, the second will byteswap
it if host operates in BE mode.
Changes are trivial sed like replacement of __raw_xxx functions
with xxx_relaxed variant.
Signed-off-by: Victor Kamensky <victor.kamensky@linaro.org> Signed-off-by: Taras Kondratiuk <taras.kondratiuk@linaro.org> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The root cause of these "inverted" sysfs removals have now been found,
so there is no need for this patch. Keep this functionality around so
that this type of error doesn't show up in driver code again.
Cc: Mika Westerberg <mika.westerberg@linux.intel.com> Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Tue, 26 Nov 2013 07:33:45 +0000 (08:33 +0100)]
ALSA: hda - Create Headhpone Mic Jack Mode when really needed
When a headphone jack is configurable as input, the generic parser
tries to make it retaskable as Headphone Mic. The switching can be
done smoothly if Capture Source control exists (i.e. there is another
input source). Or when user explicitly enables the creation of jack
mode controls, "Headhpone Mic Jack Mode" will be created accordingly.
However, if the headphone mic is the only input source, we have to
create "Headphone Mic Jack Mode" control because there is no capture
source selection. Otherwise, the generic parser assumes that the
input is constantly enabled, thus the headphone is permanently set
as input. This situation happens on the old MacBook Airs where no
input is supported properly, for example.
This patch fixes the problem: now "Headphone Mic Jack Mode" is created
when such an input selection isn't possible.
Linus Walleij [Wed, 27 Nov 2013 07:47:02 +0000 (08:47 +0100)]
gpio: pl061: move irqdomain initialization
The PL061 driver had the irqdomain initialization in an unfortunate
place: when used with device tree (and thus passing the base IRQ
0) the driver would work, as this registers an irqdomain and waits
for mappings to be done dynamically as the devices request their
IRQs, whereas when booting using platform data the irqdomain core
would attempt to allocate IRQ descriptors dynamically (which works
fine) but also to associate the irq_domain_associate_many() on all
IRQs, which in turn will call the mapping function which at this
point will try to set the type of the IRQ and then tries to acquire
a non-initialized spinlock yielding a backtrace like this:
This moves the irqdomain initialization to a point where the spinlock
and GPIO chip are both fully propulated, so the callbacks can be used
without crashes.
I had some problem reproducing the crash, as the devm_kzalloc():ed
zeroed memory would seemingly mask the spinlock as something OK,
but by poisoning the lock like this:
u32 *dum;
dum = (u32 *) &chip->lock;
*dum = 0xaaaaaaaaU;
I could reproduce, fix and test the patch.
Reported-by: Russell King <linux@arm.linux.org.uk> Cc: Rob Herring <robherring2@gmail.com> Cc: Haojian Zhuang <haojian.zhuang@linaro.org> Cc: Baruch Siach <baruch@tkos.co.il> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Thomas Pugliese [Tue, 26 Nov 2013 19:58:15 +0000 (13:58 -0600)]
ALSA: usb: use multiple packets per urb for Wireless USB inbound audio
For Wireless USB audio devices, use multiple isoc packets per URB for
inbound endpoints with a datainterval < 5. This allows the WUSB host
controller to take advantage of bursting to service endpoints whose
logical polling interval is less than the 4ms minimum polling interval
limit in WUSB.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Thomas Gleixner [Thu, 21 Nov 2013 11:41:44 +0000 (12:41 +0100)]
sched: Expose preempt_schedule_irq()
Tony reported that aa0d53260596 ("ia64: Use preempt_schedule_irq")
broke PREEMPT=n builds on ia64.
Ok, wrapped my brain around it. I tripped over the magic asm foo which
has a single need_resched check and schedule point for both sys call
return and interrupt return.
So you need the schedule_preempt_irq() for kernel preemption from
interrupt return while on a normal syscall preemption a schedule would
be sufficient. But using schedule_preempt_irq() is not harmful here in
any way. It just sets the preempt_active bit also in cases where it
would not be required.
Even on preempt=n kernels adding the preempt_active bit is completely
harmless. So instead of having an extra function, moving the existing
one out of the ifdef PREEMPT looks like the sanest thing to do.
It would also allow getting rid of various other sti/schedule/cli asm
magic in other archs.
Reported-and-Tested-by: Tony Luck <tony.luck@gmail.com> Fixes: aa0d53260596 ("ia64: Use preempt_schedule_irq") Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[slightly edited Changelog] Signed-off-by: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/alpine.DEB.2.02.1311211230030.30673@ionos.tec.linutronix.de Signed-off-by: Ingo Molnar <mingo@kernel.org>
David Herrmann [Tue, 26 Nov 2013 12:58:18 +0000 (13:58 +0100)]
HID: uhid: fix leak for 64/32 UHID_CREATE
UHID allows short writes so user-space can omit unused fields. We
automatically set them to 0 in the kernel. However, the 64/32 bit
compat-handler didn't do that in the UHID_CREATE fallback. This will
reveal random kernel heap data (of random size, even) to user-space.
Fixes: befde0226a59 ('HID: uhid: make creating devices work on 64/32 systems') Reported-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David Herrmann <dh.herrmann@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Hui Wang [Wed, 27 Nov 2013 06:47:26 +0000 (14:47 +0800)]
ALSA: hda - Enable mute/mic-mute LEDs for more Thinkpads with Conexant codec
Most Thinkpad Edge series laptops use conexant codec, so far although
the codecs have different minor Vendor Id and minor Subsystem Id,
they all belong to the cxt5066 family, this change can make the
mute/mic-mute LEDs support more generic among cxt_5066 family.
This design refers to the similar solution for the realtek codec
ALC269 family in the patch_realtek.c.
Cc: Alex Hung <alex.hung@canonical.com> Signed-off-by: Hui Wang <hui.wang@canonical.com> Acked-by: David Henningsson <david.henningsson@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
This causes the ftrace internal accounting to get screwed up and
crashes ftrace, preventing the user from using the function tracer
after that.
2) if a TRACE_EVENT has a string field, and NULL is given for it.
The internal trace event code does a strlen() and strcpy() on the
source of field. If it is NULL it causes the system to oops.
This bug has been there since 2.6.31, but no TRACE_EVENT ever passed
in a NULL to the string field, until now"
* tag 'trace-fixes-v3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftrace: Fix function graph with loading of modules
tracing: Allow events to have NULL strings
Linus Torvalds [Wed, 27 Nov 2013 02:02:46 +0000 (18:02 -0800)]
Merge branch 'for-linus-bugs' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull ceph bug-fixes from Sage Weil:
"These include a couple fixes to the new fscache code that went in
during the last cycle (which will need to go stable@ shortly as well),
a couple client-side directory fragmentation fixes, a fix for a race
in the cap release queuing path, and a couple race fixes in the
request abort and resend code.
Obviously some of this could have gone into 3.12 final, but I
preferred to overtest rather than send things in for a late -rc, and
then my travel schedule intervened"
* 'for-linus-bugs' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
ceph: allocate non-zero page to fscache in readpage()
ceph: wake up 'safe' waiters when unregistering request
ceph: cleanup aborted requests when re-sending requests.
ceph: handle race between cap reconnect and cap release
ceph: set caps count after composing cap reconnect message
ceph: queue cap release in __ceph_remove_cap()
ceph: handle frag mismatch between readdir request and reply
ceph: remove outdated frag information
ceph: hung on ceph fscache invalidate in some cases
powerpc/windfarm: Fix XServe G5 fan control Makefile issue
We are missing building windfarm_max6690_sensor.o when building
CONFIG_WINDFARM_RM31. Usually all the windfarm drivers are built
and thus this isn't a problem but some more "tailored" setups
(Gentoo ?) building only that driver are not working because
the require sensor module is missing.
Reported-by: Stanislav Ponomarev <devhexorg@gmail.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* acpica:
ACPI: Clean up incorrect inclusions of ACPICA headers
ACPICA: Update version to 20131115.
ACPICA: Add support to delete all objects attached to the root namespace node.
ACPICA: Delete all attached data objects during namespace node deletion.
ACPICA: Resources: Fix loop termination for the get AML length function.
ACPICA: Tests: Add CHECKSUM_ABORT protection for test utilities.
ACPICA: Debug output: Do not emit function nesting level for kernel build.
Linus Torvalds [Tue, 26 Nov 2013 19:18:37 +0000 (11:18 -0800)]
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Mostly bugfixes and a few small code removals. Worth pointing out is:
- A handful of more fixes to get DT enablement working properly on
OMAP, finding new breakage of things that don't work quite right
yet without the traditional board files. I expect a bit more of
this to come in this release as people test on their hardware.
- Implementation of power_down_finish() on vexpress, to make kexec
work and to stop the MCPM core to produce a warning (the warning
was new to 3.13-rc1).
- A handful of minor fixes for various platforms"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: bcm2835: add missing #xxx-cells to I2C nodes
ARM: dts: Add max77686 RTC interrupt to cros5250-common
ARM: vexpress/TC2: Implement MCPM power_down_finish()
ARM: tegra: Provide dummy powergate implementation
ARM: omap: fix warning with LPAE build
ARM: OMAP2+: Remove legacy omap4_twl6030_hsmmc_init
ARM: OMAP2+: Remove legacy mux code for display.c
ARM: OMAP2+: Fix undefined reference to set_cntfreq
gpio: twl4030: Fix passing of pdata in the device tree case
gpio: twl4030: Fix regression for twl gpio output
ARM: OMAP2+: More randconfig fixes for reconfigure_io_chain
ARM: dts: imx6qdl: disable spdif "rxtx5" clock option
ARM: dts: Fix omap2 specific dtsi files by adding the missing entries
ARM: OMAP2+: Fix GPMC and simplify bootloader timings for 8250 and smc91x
i2c: omap: Fix missing device tree flags for omap2
Linus Torvalds [Tue, 26 Nov 2013 19:16:54 +0000 (11:16 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull IMA fixes from James Morris:
"These three patches fix regressions in the IMA code in your current
tree.
The first fixes a couple of bugs in template_desc_init_fields(), and
the other two ensure that changes in this kernel don't break
userspace"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
ima: make a copy of template_fmt in template_desc_init_fields()
ima: do not send field length to userspace for digest of ima template
ima: do not include field length in template digest calc for ima template
Linus Torvalds [Tue, 26 Nov 2013 19:15:12 +0000 (11:15 -0800)]
Merge tag 'ntb-3.13' of git://github.com/jonmason/ntb
Pull non-transparent bridge updates from Jon Mason:
"NTB driver bug fixes to address a missed call to pci_enable_msix,
NTB-RP Link Up issue, Xeon Doorbell errata workaround, ntb_transport
link down race, and correct dmaengine_get/put usage.
Also, clean-ups to remove duplicate defines and document a hardware
errata. Finally, some changes to improve performance"
* tag 'ntb-3.13' of git://github.com/jonmason/ntb:
NTB: Disable interrupts and poll under high load
NTB: Enable Snoop on Primary Side
NTB: Document HW errata
NTB: remove duplicate defines
NTB: correct dmaengine_get/put usage
NTB: Fix ntb_transport link down race
ntb: Fix missed call to pci_enable_msix()
NTB: Fix NTB-RP Link Up
NTB: Xeon Doorbell errata workaround
ftrace: Fix function graph with loading of modules
Commit 8c4f3c3fa9681 "ftrace: Check module functions being traced on reload"
fixed module loading and unloading with respect to function tracing, but
it missed the function graph tracer. If you perform the following
The above mentioned commit didn't go far enough. Well, it covered the
function tracer by adding checks in __register_ftrace_function(). The
problem is that the function graph tracer circumvents that (for a slight
efficiency gain when function graph trace is running with a function
tracer. The gain was not worth this).
The problem came with ftrace_startup() which should always be called after
__register_ftrace_function(), if you want this bug to be completely fixed.
Anyway, this solution moves __register_ftrace_function() inside of
ftrace_startup() and removes the need to call them both.
Reported-by: Dave Wysochanski <dwysocha@redhat.com> Fixes: ed926f9b35cd ("ftrace: Use counters to enable functions to trace") Cc: stable@vger.kernel.org # 3.0+ Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
New tracepoints have been added that have allowed for NULL pointers
being assigned to strings. To fix this, change the TRACE_EVENT() code
to check for NULL and if it is, it will assign "(null)" to it instead
(similar to what glibc printf does).
can: flexcan: use correct clock as base for bit rate calculation
The flexcan IP core uses the peripheral clock ("per") as basic clock for the
bit timing calculation. However the driver uses the the wrong clock ("ipg").
This leads to wrong bit rates if the rates on both clock are different.
This patch fixes the problem by using the correct clock for the bit rate
calculation.
Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Martin Vogt [Sun, 24 Nov 2013 14:57:23 +0000 (15:57 +0100)]
i2c: i2c-diolan-u2c: different usb endpoints for DLN-2-U2C
The previous diolan adapter uses other out/in endpoints than
the current DLN-2-U2C in compatibility mode.
They changed from 0x2/0x84 to 0x3/0x83.
This patch gets the endpoints from the usb interface, instead
of hardcode them in the driver.
This was tested on a current DLN-2-U2C board.
Signed-off-by: Martin Vogt <mvogt1@gmail.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Takashi Iwai [Tue, 26 Nov 2013 10:58:40 +0000 (11:58 +0100)]
ALSA: hda - Drop bus->avoid_link_reset flag
Use bus->power_keep_link_on instead. The controller shouldn't go to
D3 when the link isn't reset, so essentially avoiding the link reset
means avoiding the runtime PM.
Taras Kondratiuk [Wed, 20 Nov 2013 18:23:44 +0000 (20:23 +0200)]
i2c: davinci: raw read and write endian fix
I2C IP block expect LE data, but CPU may operate in BE mode.
Need to use endian neutral functions to read/write h/w registers.
I.e instead of __raw_read[lw] and __raw_write[lw] functions code
need to use read[lw]_relaxed and write[lw]_relaxed functions.
If the first simply reads/writes register, the second will byteswap
it if host operates in BE mode.
Changes are trivial sed like replacement of __raw_xxx functions
with xxx_relaxed variant.
Stephen Warren [Tue, 26 Nov 2013 03:35:42 +0000 (20:35 -0700)]
ARM: bcm2835: add missing #xxx-cells to I2C nodes
The I2C controller node needs #address-cells and #size-cells properties,
but these are currently missing. Add them. This allows child nodes to be
parsed correctly.
Cc: stable@vger.kernel.org Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Olof Johansson <olof@lixom.net>
Mattia Dongili [Mon, 25 Nov 2013 22:43:50 +0000 (07:43 +0900)]
sony-laptop: do not scribble keyboard backlight registers on resume
Follow-up to commit 294d31e8227c ("sony-laptop: don't change keyboard
backlight settings"): avoid messing up the state on resume. Leave it to
what was before suspending as it's anyway likely that we still don't
know what value we should write to the EC registers. This fix is also
required in 3.12
Lv Zheng [Fri, 22 Nov 2013 23:27:27 +0000 (07:27 +0800)]
ACPI: Clean up incorrect inclusions of ACPICA headers
Header file <acpi/acpi.h> contains environemnt settings and architecture
specific implementation that should be included before any other ACPICA
headers in order to keep a consistent build environment for ACPICA users.
The following internal ACPICA header files should be included from
<acpi/acpi.h> and should not be included by other kernel files:
<acpi/acpiosxf.h>
<acpi/acpixf.h>
Clean up incorrect inclusions of these files from non-ACPICA source
files.
[rjw: Subject and changelog] Signed-off-by: Lv Zheng <lv.zheng@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Doug Anderson [Wed, 23 Oct 2013 13:11:01 +0000 (06:11 -0700)]
ARM: dts: Add max77686 RTC interrupt to cros5250-common
Without the interrupt you'll get problems if you enable
CONFIG_RTC_DRV_MAX77686. Setup the interrupt properly in the device
tree.
Signed-off-by: Doug Anderson <dianders@chromium.org> Tested-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Olof Johansson <olof@lixom.net> Cc: stable@vger.kernel.org
This patch implements the power_down_finish() method for TC2, to
enable the kernel to confirm when CPUs are safely powered down.
The information required for determining when a CPU is parked
cannot be obtained from any single place, so a few sources of
information must be combined:
* mcpm_cpu_power_down() must be pending for the CPU, so that we
don't get confused by false STANDBYWFI positives arising from
CPUidle. This is detected by waiting for the tc2_pm use count
for the target CPU to reach 0.
* Either the SPC must report that the CPU has asserted
STANDBYWFI, or the TC2 tile's reset control logic must be
holding the CPU in reset.
Just checking for STANDBYWFI is not sufficient, because this
signal is not latched when the the cluster is clamped off and
powered down: the relevant status bits just drop to zero. This
means that STANDBYWFI status cannot be used for reliable
detection of the last CPU in a cluster reaching WFI.
This patch is required in order for kexec to work with MCPM on TC2.
MCPM code was changed in commit 0de0d6467525 ('ARM: 7848/1: mcpm:
Implement cpu_kill() to synchronise on powerdown'), and since then it
will hit a WARN_ON_ONCE() due to power_down_finish not being implemented
on the TC2 platform.
Signed-off-by: Dave Martin <Dave.Martin@arm.com> Acked-by: Pawel Moll <pawel.moll@arm.com> Reviewed-by: Nicolas Pitre <nico@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
Thomas Renninger [Sat, 16 Nov 2013 13:39:22 +0000 (14:39 +0100)]
tools: cpupower: fix wrong err msg not supported vs not available
idlestates in sysfs are counted from 0.
This fixes a wrong error message.
Current behavior on a machine with 4 sleep states is:
cpupower idle-set -e 4
Idlestate 4 enabled on CPU 0
-----Wrong---------------------
cpupower idle-set -e 5
Idlestate enabling not supported by kernel
-----Must and now will be -----
cpupower idle-set -e 5
Idlestate 6 not available on CPU 0
-------------------------------
cpupower idle-set -e 6
Idlestate 6 not available on CPU 0
Signed-off-by: Thomas Renninger <trenn@suse.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Thierry Reding [Mon, 25 Nov 2013 18:49:47 +0000 (11:49 -0700)]
ARM: tegra: Provide dummy powergate implementation
In order to support increased build test coverage for drivers, implement
dummies for the powergate implementation. This will allow the drivers to
be built without requiring support for Tegra to be selected.
This patch solves the following build errors, which can be triggered in
v3.13-rc1 by selecting DRM_TEGRA without ARCH_TEGRA:
drivers/built-in.o: In function `gr3d_remove':
drivers/gpu/drm/tegra/gr3d.c:321: undefined reference to `tegra_powergate_power_off'
drivers/gpu/drm/tegra/gr3d.c:325: undefined reference to `tegra_powergate_power_off'
drivers/built-in.o: In function `gr3d_probe':
drivers/gpu/drm/tegra/gr3d.c:266: undefined reference to `tegra_powergate_sequence_power_up'
drivers/gpu/drm/tegra/gr3d.c:273: undefined reference to `tegra_powergate_sequence_power_up'
Signed-off-by: Thierry Reding <treding@nvidia.com>
[swarren, updated commit description] Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 19 Nov 2013 19:50:37 +0000 (11:50 -0800)]
Merge tag 'omap-for-v3.13/more-fixes-for-merge-window-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
Few more fixes for issues found booting older omaps using device tree.
Also few randconfig build fixes and removal of some dead code for omap4
as it no longer has legacy platform data based booting support.
* tag 'omap-for-v3.13/more-fixes-for-merge-window-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Remove legacy omap4_twl6030_hsmmc_init
ARM: OMAP2+: Remove legacy mux code for display.c
ARM: OMAP2+: Fix undefined reference to set_cntfreq
gpio: twl4030: Fix passing of pdata in the device tree case
gpio: twl4030: Fix regression for twl gpio output
ARM: OMAP2+: More randconfig fixes for reconfigure_io_chain
ARM: dts: Fix omap2 specific dtsi files by adding the missing entries
ARM: OMAP2+: Fix GPMC and simplify bootloader timings for 8250 and smc91x
i2c: omap: Fix missing device tree flags for omap2
Olof Johansson [Wed, 13 Nov 2013 06:51:28 +0000 (22:51 -0800)]
ARM: omap: fix warning with LPAE build
Some omap3 code is throwing a warning:
arch/arm/mach-omap2/pm34xx.c: In function 'omap3_save_secure_ram_context':
arch/arm/mach-omap2/pm34xx.c:123:32: warning: cast to pointer from
integer of different size [-Wint-to-pointer-cast]
In reality this code will never actually execute with LPAE=y, since
Cortex-A8 doesn't support it. So downcasting the __pa() is safe in
this case.
Signed-off-by: Olof Johansson <olof@lixom.net> Acked-by: Tony Lindgren <tony@atomide.com>
Laxman Dewangan [Mon, 25 Nov 2013 14:09:47 +0000 (19:39 +0530)]
irq: Enable all irqs unconditionally in irq_resume
When the system enters suspend, it disables all interrupts in
suspend_device_irqs(), including the interrupts marked EARLY_RESUME.
On the resume side things are different. The EARLY_RESUME interrupts
are reenabled in sys_core_ops->resume and the non EARLY_RESUME
interrupts are reenabled in the normal system resume path.
When suspend_noirq() failed or suspend is aborted for any other
reason, we might omit the resume side call to sys_core_ops->resume()
and therefor the interrupts marked EARLY_RESUME are not reenabled and
stay disabled forever.
To solve this, enable all irqs unconditionally in irq_resume()
regardless whether interrupts marked EARLY_RESUMEhave been already
enabled or not.
This might try to reenable already enabled interrupts in the non
failure case, but the only affected platform is XEN and it has been
confirmed that it does not cause any side effects.
Olav Haugan [Fri, 22 Nov 2013 17:30:41 +0000 (09:30 -0800)]
staging: zsmalloc: Ensure handle is never 0 on success
zsmalloc encodes a handle using the pfn and an object
index. On hardware platforms with physical memory starting
at 0x0 the pfn can be 0. This causes the encoded handle to be
0 and is incorrectly interpreted as an allocation failure.
This issue affects all current and future SoCs with physical
memory starting at 0x0. All MSM8974 SoCs which includes
Google Nexus 5 devices are affected.
To prevent this false error we ensure that the encoded handle
will not be 0 when allocation succeeds.
Merge tag 'fixes-for-3.13a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First round of fixes for IIO in the 3.13 cycle.
The usual mixed bag of fixes.
* 3 cases where kconfig dependencies were missing. We need to keep a closer
eye on this in new drivers.
* hid_sensors was abusing the iio_dev->trigger pointer. We had a round
of clearing this out some time ago but this driver clearly slipped through.
* A misuse of the IIO_ST macro, in mcp3422, which we should really make a
concertive effort to finish removing.
* Avoid a double free introduced by recent buffer reference counting in the
one driver that (quite reasonably!) does things differently (am335x)
* A missing mutex_unlock in kxsd9 that means that driver has been non
functional for some time and no one noticed (including me who for once
actually has one of the supported devices).
* An incorrect assumption about the parameters of sign_extend32 in mcp3422.
So nothing controversial. The only substantial patch is the hid_sensors
one and that is actually just adding a new pointer to the devices private
state then moving the code over to it.
Linus Torvalds [Mon, 25 Nov 2013 20:50:08 +0000 (12:50 -0800)]
Merge tag 'regulator-v3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A bunch of fixes, a few driver specific ones and a framework fix for
voltage enumeration on fixed voltage regulators which had previously
worked but had been misplaced during some refactoring causing problems
for users that needed to know the voltage"
* tag 'regulator-v3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: arizona-micsupp: Correct wm5110 voltage selection
regulator: pfuze100: allow misprogrammed ID
regulator: fixed: fix regulator_list_voltage() for regression
regulator: gpio-regulator: Don't oops on missing regulator-type property
Holger Bechtold [Mon, 25 Nov 2013 14:48:19 +0000 (15:48 +0100)]
can: c_can: fix calculation of transmitted bytes on tx complete
The number of bytes transmitted was not updated correctly, if several CAN
messages (with different length) were transmitted in one 'bunch'. Thus
programs like 'ifconfig' showed wrong transmit byte counts. Reason was, that
the message object whose DLC is to be read was not necessarily the active one
at the time when
can: c_can: don't call pm_runtime_get_sync() from interrupt context
The c_can driver contians a callpath (c_can_poll -> c_can_state_change ->
c_can_get_berr_counter) which may call pm_runtime_get_sync() from the IRQ
handler, which is not allowed and results in "BUG: scheduling while atomic".
This problem is fixed by introducing __c_can_get_berr_counter, which will not
call pm_runtime_get_sync().
Reported-by: Andrew Glen <AGlen@bepmarine.com> Tested-by: Andrew Glen <AGlen@bepmarine.com> Signed-off-by: Andrew Glen <AGlen@bepmarine.com> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Oliver Hartkopp [Thu, 21 Nov 2013 17:03:07 +0000 (18:03 +0100)]
can: sja1000: fix {pre,post}_irq() handling and IRQ handler return value
This patch fixes the issue that the sja1000_interrupt() function may have
returned IRQ_NONE without processing the optional pre_irq() and post_irq()
function before. Further the irq processing counter 'n' is moved to the end of
the while statement to return correct IRQ_[NONE|HANDLED] values at error
conditions.
Reported-by: Wolfgang Grandegger <wg@grandegger.com> Acked-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>