The bcdDevice field is defined as
|Device release number in binary-coded decimal
in the USB 2.0 specification. We use this field to distinguish the UDCs
from each other. In theory this could be used on the host side to apply
certain quirks if the "special" UDC in combination with this gadget is
used. This hasn't been done as far as I am aware. In practice it would
be better to fix the UDC driver before shipping since a later release
might not need this quirk anymore.
There are some driver in tree (on the host side) which use the bcdDevice
field to figure out special workarounds for a given firmware revision.
This seems to make sense. Therefore this patch converts all gadgets
(except a few) to use the kernel version instead a random 2 or 3 plus
the UDC number. The few that don't report kernel's version are:
- webcam
This one reports always a version 0x10 so allow it to do so in future.
- nokia
This one reports always 0x211. The comment says that this gadget works
only if the UDC supports altsettings so I added a check for this.
- serial
This one reports 0x2400 + UDC number. Since the gadget version is 2.4
this could make sense. Therefore bcdDevice is 0x2400 here.
I also remove various gadget_is_<name> macros which are unused. The
remaining few macros should be moved to feature / bug bitfield.
Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: gadget: libcomposite: move MODULE_VERSION to composite.c
MODULE_VERSION and AUTHOR looks better in composite.c than in
usbstrings.c so I move it there.
I put David Brownell as the module Author as I belive he wrote most of
it.
Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: gadget: libcomposite: move composite.c into libcomposite
This moves composite.c into libcomposite and updates all gadgets.
Finally!
Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: gadget: Provide a default implementation of default manufacturer string
Some gadgets provide custom entry here. Some may override it with an
etntry that is also created by composite if there was no value sumbitted
at all.
This patch removes all "custom manufacturer" strings which are the same
as these which are created by composite. Then it moves the creation of
the default manufacturer string to usb_composite_overwrite_options() in
case no command line argument has been used and the entry is still an
empty string.
By doing this we get rid of the global variable "composite_manufacturer"
in composite.
Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: gadget: remove string override from struct usb_composite_driver
The struct usb_composite_driver members iProduct, iSerial and
iManufacturer can be entered directly via the string array. There is no
need for them to appear here.
Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch pushes the iProduct module argument from composite
into each gadget.
Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch pushes the iManufacturer module argument from composite into
each gadget. Once the user uses the module paramter, the string is
overwritten with the final value.
Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch pushes the iSerialNumber module argument from composite into
each gadget. Once the user uses the module paramter, the string is
overwritten with the final value.
Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: gadget: make sure each gadget is using same index for Product, Serial,…
The index in usb_string array is defined by the gadget. The gadget can
choose which index entry it assigns for the serial number and which the
product name. The gadget has just to ensure that the descriptor contains
the proper string id which is assigned by composite.
If the composite layer knows the index of the "default" information
which will be overwritten by module parameters, it can be used later to
overwrite it.
Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: gadget: push VID/PID/USB BCD module option into gadgets
This patch moves the module options idVendor, idProduct and bcdDevice
from composite.c into each gadgets. This ensures compatibility with
current gadgets and removes the global variable which brings me step
closer towards composite.c in libcomposite
Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: gadget: move usb_gadget_controller_number() into a .c file and libcomposite
After I moved the function from the header file to the c file I see:
| $ size drivers/usb/gadget/gadget_chips.o
| text data bss dec hex filename
| 1048 0 0 1048 418 drivers/usb/gadget/gadget_chips.o
That is almost a KiB which is removed from each user.
As Felipe pointed out, the function / usage is very dumb actually. This is
used for the following reasons:
- epautoconf ep hint (could provide a per-gadget callback)
- miss-features. currently the missing altsetting on pxa's and something
ZLP related on musbhdrc (looks like an optimisation which could be
implemented in musb itself if it is correct)
- unique BCD accross all UDCs. Not sure how important this is.
Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: gadget: initialize the strings in tcm_usb_gadget properly
I have no idea what I've been thinking while I was doing this in the first
place. Now the strings are initialized properly and reported by lsusb.
Cc: stable@vger.kernel.org # v3.5 Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
This was broken in 2e87edf49 ("usb: gadget: make g_printer use
composite").
The USB-strings were not setup properly and were not used. No function
was added which results in an empty USB config.
While fixing this, the interface number is now auto generated and not
hard coded to 0.
Cc: stable@vger.kernel.org # v3.5 Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: gadget: use usb_string_ids_tab instead multiple usb_string_id()
Using usb_string_ids_tab() instead multiple calls of usb_string_id()
seems to be handy. It also allows to add string without many checks.
Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: gadget: make composite module options readonly only
This is a partly revert of 4fffd6e5 ("usb: gadget: composite: make
module parameters accessible at runtime").
It is not possible to change the VID or other property for a gadget
right now. This change has been made for Anrdoid gadget which has this
functionality in its copy of the file. This function is executed currently
only once and most caller in tree are __init.
Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: gadget: remove bufsiz from struct usb_composite_dev
there is no read user of bufsiz, its content is available via
USB_COMP_EP0_BUFSIZ. Remove it.
Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: gadget: move USB_BUFSIZ into global composite.h
This patch moves USB_BUFSIZ into global header file as
USB_COMP_EP0_BUFSIZ. There is currently only one user (f_sourcesink)
besides composite which need it. Ideally f_sourcesink would have its
own ep0 buffer. Lets keep it that way it was for now.
Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: gadget: libcomposite: add epautoconf.c to libcomposite
This patch adds epautoconf.c into libcomposite and updates all gadgets.
Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: gadget: move global vars from epautoconf into struct usb_gadget
epautoconf has two global variables which count the endpoint number of
last assigned endpoint.
This patch removes the global variable and keeps it as per (UDC) gadget.
While here, the ifdef is removed and now the in and outpoint are
enumerated unconditionally. The dwc3 for instance supports 32 endpoints
in total.
Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: gadget: libcomposite: move config.c into libcomposite
This patch moves config.c into libcomposite and updates all gadgets.
Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch aims to be simple. It removes #include usbstribgs.c line from each
gadget and creates libcomposite.ko which has only one member, that is
usbstribgs.c.
Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: gadget: pxa25x: make it compile with debug again
|drivers/usb/gadget/pxa25x_udc.h: In function 'dump_state':
|drivers/usb/gadget/pxa25x_udc.h:228:20: error: invalid type argument of '->' (have 'struct usb_ep')
Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: gadget: remove global variable composite in composite.c
This patch removes the global variable composite in composite.c.
The private data which was saved there is now passed via an additional
argument to the bind() function in struct usb_gadget_driver.
Only the "old-style" UDC drivers have to be touched here, new style are
doing it right because this change is made in udc-core.
Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
This Android gadget includes a bunch of .c files. Fixing normal gadgets
is not the real problem but this gadget is not always fixable since the
problem here are fundumential / design.
*I* wanted to get this removed but other people want to keep it even
though there were reports that Android itself is not using it. Some
poeple think that it is better to have this instead of nothing and other
argue that they need sdb and mass storage gadget. The sdb function is
not provided by ccg so I don't see the point of this. I don't see any
logical reasoning behind it and I decided that it is time for retreat.
This patch brings all dependencies of ccg into staging so I can do
whatever I want in drivers/usb/gadget without breaking ccg.
Cc: devel@driverdev.osuosl.org Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: gadget: move bind() callback back to struct usb_gadget_driver
This partly reverts 07a18bd7 ("usb gadget: don't save bind callback in
struct usb_composite_driver") and fixes new drivers. The section missmatch
problems was solved by whitelisting bind callback in modpost.
Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: gadget: move bind() callback back to struct usb_composite_driver
This partly reverts 07a18bd7 ("usb gadget: don't save bind callback in
struct usb_composite_driver") and fixes new drivers. The section missmatch
problems was solved by whitelisting structs in question via __ref.
Cc: devel@driverdev.osuosl.org Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: gadget: push all usb_composite_driver structs into __refdata
As it turns out, Sam's comment was better than I initially assumed. This
patch pushes as struct usb_composite_driver data structures into
__refdata section to avoid a section missmatch report from modpost
because the ->bind() can be marked __init. The only downside is that
modpost does not check between ->bind() and other member. However, it is
temporary.
Cc: Sam Ravnborg <sam@ravnborg.org> Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
avoids the following section missmatch
|WARNING: drivers/usb/gadget/g_audio.o(.init.text+0x2e7): Section
|mismatch in reference from the function afunc_bind() to the function
|.devexit.text:snd_uac2_remove()
|The function __init afunc_bind() references
|a function __devexit snd_uac2_remove().
|This is often seen when error handling in the init function
|uses functionality in the exit path.
|The fix is often to remove the __devexit annotation of
|snd_uac2_remove() so it may be used outside an exit section.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: gadget: move bind callback into driver struct usb_composite_driver
It was moved to be an argument in 07a18bd716ed5 ("usb gadget: don't
save bind callback in struct usb_composite_driver"). The reason was to
avoid the section missmatch. The warning was shown because ->bind is
marked as __init becuase it is a one time init. The warning can be also
suppresed by whitelisting the variable i.e. rename it to lets say _probe.
Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
staging: ccg: Add a note about compatibility issues.
The first item on the todo list is a new user interface. Put this
information into Kconfig's help entry to people are not too confusing
once an user API changes which does not happen in kernel otherwise.
Cc: devel@driverdev.osuosl.org Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
Kevin Cernekee [Sat, 25 Aug 2012 19:38:52 +0000 (12:38 -0700)]
usb: gadget: bcm63xx UDC driver
Driver for the "USB20D" / "USBD" block on BCM6328, BCM6368, BCM6816,
BCM6362, BCM3383, and others.
The hardware block was designed to support networking applications
(direct connection of a home router to a PC), and the endpoint
configuration is fixed.
[ balbi@ti.com : dropped USB_GADGET_DUALSPEED from Kconfig ]
Signed-off-by: Kevin Cernekee <cernekee@gmail.com> Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc> Signed-off-by: Felipe Balbi <balbi@ti.com>
devm_* functions are used to replace kzalloc, request_mem_region, ioremap
clk_get and request_irq functions in probe call. With the usage of devm_*
functions explicit freeing and unmapping is not required.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: gadget: get rid of USB_GADGET_{DUAL,SUPER}SPEED
This commit removes USB_GADGET_DUALSPEED and USB_GADGET_SUPERSPEED
Kconfig options. Since now kernel allows many UDC drivers to be
compiled, those options may turn to no longer be valid. For
instance, if someone decides to build UDC that supports super
speed and UDC that supports high speed only, the latter will be
"assumed" to support super speed since USB_GADGET_SUPERSPEED will
be selected by the former.
The test of whether CONFIG_USB_GADGET_*SPEED was defined was just
an optimisation which removed otherwise dead code (ie. if UDC is
not dual speed, there is no need to handle cases that can happen
if speed is high). This commit removes those checks.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Alan Stern [Mon, 20 Aug 2012 20:12:47 +0000 (16:12 -0400)]
usb: gadget: dummy-hcd: remember to update driver pointer
This patch (as1599) fixes dummy-hcd to make it update the appropriate
driver pointer when a new gadget driver is bound or unbound. Without
this change, the gadget driver's name doesn't appear in dev_printk
output.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Felipe Balbi <balbi@ti.com>
Roland Stigge [Mon, 20 Aug 2012 08:30:14 +0000 (10:30 +0200)]
usb: gadget: lpc32xx_udc: Support multiple controllers
The lpc32xx_udc driver supported only one controller by defining a global
static struct for it. This patch enables multiple instances of the controller
by dynamic allocation of the struct at probe(). A static struct is kept as a
template on initialization since it does some complex preset, reflecting fixed
hardware endpoint structure.
Signed-off-by: Roland Stigge <stigge@antcom.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch removes the utilization of struct usb_endpoint_descriptor, as done
by other drivers also. This was done on request by the USB gadget maintainers,
since this API is obsoleted.
Signed-off-by: Roland Stigge <stigge@antcom.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: renesas_usbhs: modify the irq handler for sharing irq
When IORESOURCE_IRQ_SHAREABLE is set, the irq handler may be called
even if the interupt of the USB module doesn't happen. So, it may
clear the interrupt flags by mistake. This patch fixes it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Kevin Cernekee [Thu, 9 Aug 2012 08:23:52 +0000 (11:23 +0300)]
usb: gadget: udc-core: Race between disconnect/unbind and setup
usb_gadget_remove_driver() runs through a four-step sequence to shut down
the gadget driver. For the case of a composite gadget + at91 UDC, this
would look like:
The UDC driver can receive SETUP packets from the host up until the
point when usb_gadget_disconnect() returns. On rare occasions, the
gadget driver may see this sequence:
Andy Shevchenko [Tue, 7 Aug 2012 16:07:58 +0000 (19:07 +0300)]
usb: gadget: use native print_hex_dump_bytes()
Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
The timeout values were 1000 and timeout issue occured many times on my
s3c6410 Soc based board (mostly when booting whith USB cable not
connected). This patch increase the values to 10000 to guarantee the
success of reset.
Having set timeout to 10000, I printed the remained timeout values
which could cause timeout issue before this change (tested several
times).
the first timeout value remained:
timeout = 8079
timeout = 8079
timeout = 8078
timeout = 8081
the second timeout value remained:
timeout = 7940
timeout = 7945
timeout = 7940
timeout = 7938
Seeing from above values, I think the value 10000 is big enough.
Signed-off-by: Du, Changbin <changbin.du@gmail.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Neil Zhang [Tue, 10 Jul 2012 02:07:07 +0000 (10:07 +0800)]
usb: gadget: mv_udc: fix boot up hang
Fix boot up hang when enable udc without otg enabled.
The root cause is that the clock will be shut down when probe routine is
finished because of clock gating. When a gadget driver is registered at
this time, it will call mv_udc_start which in turn will call
mv_udc_vbus_session. If there is no cable attached at the boot up time,
the vbus is low, so it will call stop_activity path without clock
enabled which will cause system hang then.
Actually, we need't go this path when clock is disabled, what we need to
do is just jump out.
Signed-off-by: Neil Zhang <zhangwm@marvell.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Neil Zhang [Tue, 10 Jul 2012 02:07:04 +0000 (10:07 +0800)]
usb: gadget: mv_udc: enable stream mode
According to ChipIdea's reference manual in section 8.5.2
"Non-streaming operational mode in device mode", we'd better enable stream
mode, especially that ISO endpoints are not supported when the SDIS bit
is set.
Signed-off-by: Neil Zhang <zhangwm@marvell.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Neil Zhang [Tue, 10 Jul 2012 02:07:03 +0000 (10:07 +0800)]
usb: gadget: mv_udc: avoid sleeping on spinlock
build_dtd() can be called when hold a spinlock, but GFP_KERNEL may cause
dma_pool_alloc() sleep, So we need use GFP_ATOMIC instead of GFP_KERNEL.
But using GFP_ATOMIC may cause failure when allocating memory, add error
handler to handle it.
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru> Signed-off-by: Neil Zhang <zhangwm@marvell.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Neil Zhang [Tue, 10 Jul 2012 02:07:01 +0000 (10:07 +0800)]
usb: gadget: mv_udc: reduce the delay interval
There are several places use udelay(LOOPS_USEC) to wait the status to be
changed, but the delay interval is a bit too long, so reduce it to
enhance the performance.
Signed-off-by: Neil Zhang <zhangwm@marvell.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Ian Kent [Mon, 6 Aug 2012 01:37:47 +0000 (09:37 +0800)]
autofs4 - fix get_next_positive_subdir()
Following a report of a crash during an automount expire I found that
the locking in fs/autofs4/expire.c:get_next_positive_subdir() was wrong.
Not only is the locking wrong but the function is more complex than it
needs to be.
The function is meant to calculate (and dget) the next entry in the list
of directories contained in the root of an autofs mount point (an autofs
indirect mount to be precise). The main problem was that the d_lock of
the owner of the list was not being taken when walking the list, which
lead to list corruption under load. The only other lock that needs to
be taken is against the next dentry candidate so it can be checked for
usability.
Signed-off-by: Ian Kent <raven@themaw.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 16 Aug 2012 18:47:42 +0000 (11:47 -0700)]
Merge tag 'vfio-for-v3.6-rc1' of git://github.com/awilliam/linux-vfio
Pull VFIO fix from Alex Williamson:
"Just a trivial patch to include vfio.h in the installed headers so we
can complete userspace integration into QEMU."
* tag 'vfio-for-v3.6-rc1' of git://github.com/awilliam/linux-vfio:
vfio: Include vfio.h in installed headers
Linus Torvalds [Thu, 16 Aug 2012 18:31:59 +0000 (11:31 -0700)]
Merge tag 'stable/for-linus-3.6-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen fix from Konrad Rzeszutek Wilk:
"Way back in v3.5 we added a mechanism to populate back pages that were
released (they overlapped with MMIO regions), but neglected to reserve
the proper amount of virtual space for extend_brk to work properly.
Coincidentally some other commit aligned the _brk space to larger area
so I didn't trigger this until it was run on a machine with more than
2GB of MMIO space."
* On machines with large MMIO/PCI E820 spaces we fail to boot b/c
we failed to pre-allocate large enough virtual space for extend_brk.
* tag 'stable/for-linus-3.6-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/p2m: Reserve 8MB of _brk space for P2M leafs when populating back.
Linus Torvalds [Thu, 16 Aug 2012 18:13:16 +0000 (11:13 -0700)]
Merge branch 'fixes' of git://git.infradead.org/users/vkoul/slave-dma
Pull two slave-dmaengine fixes from Vinod Koul:
"One fixes the correct use of clock API in imx driver and the other
enables clock for tegra driver, which is used for other tegra driver
conversion to dmanegine in -next."
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dma: tegra: enable/disable dma clock
dma: imx-dma: Fix kernel crash due to missing clock conversion
Linus Torvalds [Thu, 16 Aug 2012 18:08:32 +0000 (11:08 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull more drm fixes from Dave Airlie:
"Just some intel and nouveau ones this time, intel has more edp panel
fixes for macbooks and nouveau has a suspend/resume regression fix in
there."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915: Apply post-sync write for pipe control invalidates
drm/i915: reorder edp disabling to fix ivb MacBook Air
drm/nv86/fifo: suspend fix
drm/nouveau: disable copy engine on NVAF
nouveau: fixup scanout enable in nvc0_pm
drm/nouveau/aux: mask off higher bits of auxch index in i2c table entry
drm/nvd0/disp: mask off high 16 bit of negative cursor x-coordinate
drm/i915: ensure i2c adapter is all set before adding it
drm/i915: ignore eDP bpc settings from vbt
drm/i915: Fix blank panel at reopening lid
drm/nve0/fifo: add support for the flip completion swmthd
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Be less verbose during vmemmap population.
sparc64: do not clobber personality flags in sys_sparc64_personality()
Dave Airlie [Wed, 15 Aug 2012 10:31:22 +0000 (20:31 +1000)]
Merge branch 'drm-nouveau-fixes' of git://git.freedesktop.org/git/nouveau/linux-2.6 into drm-fixes
* 'drm-nouveau-fixes' of git://git.freedesktop.org/git/nouveau/linux-2.6:
drm/nv86/fifo: suspend fix
drm/nouveau: disable copy engine on NVAF
nouveau: fixup scanout enable in nvc0_pm
drm/nouveau/aux: mask off higher bits of auxch index in i2c table entry
drm/nvd0/disp: mask off high 16 bit of negative cursor x-coordinate
drm/nve0/fifo: add support for the flip completion swmthd
Dave Airlie [Wed, 15 Aug 2012 10:27:51 +0000 (20:27 +1000)]
Merge branch 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel into drm-fixes
Daniel Vetter writes:
"A few important fixers:
- fix various lvds backlight issues, regressed in 3.6 (Takashi Iwai)
- make the retina mbp work (ignore bogus edp bpc value in vbt)
- fix a gmbus regression introduced in (iirc) 3.4 (Jani Nikula)
- fix an edp panel power sequence regression, fixes the new macbook air
- apply the tlb invalidate w/a
Otherwise we still have another gmbus regression (patches are awaiting
tested-bys) and there's something odd going with some rare systems not
entering rc6 often enough (and hence blowing through too much power). It
seems to be a timing-related issue and can be mitigated by frobbing the
magic tuning parameters. We're still working on that one. Also, we still
have some fallout from the hw context support, but you can only hit that
with mesa master."
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Apply post-sync write for pipe control invalidates
drm/i915: reorder edp disabling to fix ivb MacBook Air
drm/i915: ensure i2c adapter is all set before adding it
drm/i915: ignore eDP bpc settings from vbt
drm/i915: Fix blank panel at reopening lid
David S. Miller [Wed, 15 Aug 2012 07:37:29 +0000 (00:37 -0700)]
sparc64: Be less verbose during vmemmap population.
On a 2-node machine with 256GB of ram we get 512 lines of
console output, which is just too much.
This mimicks Yinghai Lu's x86 commit c2b91e2eec9678dbda274e906cc32ea8f711da3b
(x86_64/mm: check and print vmemmap allocation continuous) except that
we aren't ever going to get contiguous block pointers in between calls
so just print when the virtual address or node changes.
This decreases the output by an order of 16.
Also demote this to KERN_DEBUG.
Signed-off-by: David S. Miller <davem@davemloft.net>
drm/i915: Only apply the SNB pipe control w/a to gen6
Note: Manually switch the pipe_control cmd to 4 dwords to avoid a
(silent) functional conflict with -next. This way will get a loud (but
conflict with next (since the scratch_addr has been deleted there).
Reported-and-tested-by: yex.tian@intel.com
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=53322 Acked-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: added note about merge conflict with -next.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm/i915: enable vdd when switching off the eDP panel
But that patch also tried to fix some neat edp sequence issue with the
force_vdd timings. Closer inspection reveals that we've raised
force_vdd only to do the aux channel communication dp_sink_dpms. If we
move the edp_panel_off below that, we don't need any force_vdd for the
disable sequence, which makes the Air happy.
Unfortunately the reporter of the original bug that the above commit
fixed is travelling, so we can't test whether this regresses things.
But my theory is that since we don't check for any power-off ->
force_vdd-on delays in edp_panel_vdd_on, this was the actual
root-cause of this failure. With that force_vdd dance completely
eliminated, I'm hopeful the original bug stays fixed, too.
For reference the old bug, which hopefully doesn't get broken by this:
https://bugzilla.kernel.org/show_bug.cgi?id=43163
In any case, regression fixers win over plain bugfixes, so this needs
to go in asap.
v2: The crucial pieces seems to be to clear the force_vdd flag
uncoditionally, too, in edp_panel_off. Looks like this is left behind
by the firmware somehow.
v3: The Apple firmware seems to switch off the panel on it's own, hence
we still need to keep force_vdd on, but properly clear it when switching
the panel off.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=45671 Tested-by: Roberto Romer <sildurin@gmail.com> Tested-by: Daniel Wagner <wagi@monom.org> Tested-by: Keith Packard <keithp@keithp.com> Cc: stable@vger.kernel.org Cc: Keith Packard <keithp@keithp.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Linus Torvalds [Tue, 14 Aug 2012 04:58:59 +0000 (07:58 +0300)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 patches from Martin Schwidefsky:
"Included are bug fixes and a patch to enable system call filtering
with BPF."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/compat: fix mmap compat system calls
s390/compat: fix compat wrappers for process_vm system calls
s390: do not clobber personality flags in sys_32_personality()
s390/seccomp: add support for system call filtering using BPF
s390/sclp_sdias: Add missing break and "fall through"
s390/mm: remove MAX_PHYSADDR_BITS define
Linus Torvalds [Tue, 14 Aug 2012 04:52:41 +0000 (07:52 +0300)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Radeon and intel fixes mostly, one fix to the mgag200 driver to not
hang on certain server variants."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (32 commits)
drm/radeon: fix typo in function header comment
drm/radeon/kms: implement timestamp userspace query (v2)
drm/radeon/kms: add MSAA texture support for r600-evergreen
drm/radeon/kms: reorder code in r600_check_texture_resource
drm/radeon: fence virtual address and free it once idle v4
drm/radeon: fix some missing parens in asic macros
drm/radeon: add some new SI pci ids
drm/radeon: fix ordering in pll picking on dce4+
drm/radeon: do not reenable crtc after moving vram start address
drm/radeon: fix bank tiling parameters on cayman
drm/radeon: fix bank tiling parameters on evergreen
drm/radeon: fix bank tiling parameters on SI
drm/radeon: properly handle crtc powergating
drm/radeon: properly handle SS overrides on TN (v2)
drm/radeon/dce4+: set a more reasonable cursor watermark
drm/radeon: fix handling for ddc type 5 on combios
drm/mgag200: fix G200ER pll picking algorithm
drm/edid: Fix potential memory leak in edid_load()
drm/udl: Use ERR_CAST inlined function instead of ERR_PTR(PTR_ERR(.. [1]
drm/radeon/kms: allow "invalid" DB formats as a means to disable DB
...
Arnd Bergmann [Mon, 13 Aug 2012 14:36:10 +0000 (14:36 +0000)]
GPIO: gpio-pxa: fix building without CONFIG_OF
Commit 7212157267 ("GPIO: gpio-pxa: fix devicetree functions") added an
"xlate" function pointer to the irq_domain_ops, but this function is nor
declared or defined anywhere when CONFIG_OF is disabled, causing the
build error:
drivers/gpio/gpio-pxa.c:532:11: error: 'irq_domain_xlate_twocell' undeclared here (not in a function)
Extending the DT-only code section to cover the irq_domain_ops and the
pxa_gpio_dt_ids solves this problem and makes it clearer which code is
actually used without DT.
Ben Skeggs [Fri, 27 Jul 2012 04:18:03 +0000 (14:18 +1000)]
drm/nouveau/aux: mask off higher bits of auxch index in i2c table entry
At least partially fixes DP output detection on W530. Not sure if more
issues remain, or if my adaptor is just behaving weirdly (it does that
sometimes).
Dave Airlie [Mon, 13 Aug 2012 23:25:01 +0000 (09:25 +1000)]
Merge branch 'drm-fixes-3.6' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
Alex Deucher writes:
This is the current set of radeon fixes for 3.6. Nothing too major.
Highlights:
- various display fixes
- some SI fixes
- new SI pci ids
- major VM fix
- CS checker support for MSAA
I've tested on a number of cards across generations and noticed no problems.
* 'drm-fixes-3.6' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix typo in function header comment
drm/radeon/kms: implement timestamp userspace query (v2)
drm/radeon/kms: add MSAA texture support for r600-evergreen
drm/radeon/kms: reorder code in r600_check_texture_resource
drm/radeon: fence virtual address and free it once idle v4
drm/radeon: fix some missing parens in asic macros
drm/radeon: add some new SI pci ids
drm/radeon: fix ordering in pll picking on dce4+
drm/radeon: do not reenable crtc after moving vram start address
drm/radeon: fix bank tiling parameters on cayman
drm/radeon: fix bank tiling parameters on evergreen
drm/radeon: fix bank tiling parameters on SI
drm/radeon: properly handle crtc powergating
drm/radeon: properly handle SS overrides on TN (v2)
drm/radeon/dce4+: set a more reasonable cursor watermark
drm/radeon: fix handling for ddc type 5 on combios
Jani Nikula [Mon, 13 Aug 2012 14:33:02 +0000 (17:33 +0300)]
drm/i915: ensure i2c adapter is all set before adding it
i2c_add_adapter() may do i2c transfers on the bus to detect supported
devices. Therefore the adapter needs to be all set before adding it. This
was not the case for the bit-banging fallback, resulting in an oops if the
device detection GMBUS transfers timed out. Fix the issue by calling
i2c_add_adapter() only after intel_gpio_setup().
LKML-Reference: <5021F00B.7000503@ionic.de> Tested-by: Mihai Moldovan <ionic@ionic.de> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jerome Glisse [Mon, 6 Aug 2012 16:32:21 +0000 (12:32 -0400)]
drm/radeon: fence virtual address and free it once idle v4
Virtual address need to be fenced to know when we can safely remove it.
This patch also properly clear the pagetable. Previously it was
serouisly broken.
Kernel 3.5/3.4 need a similar patch but adapted for difference in mutex locking.
v2: For to update pagetable when unbinding bo (don't bailout if
bo_va->valid is true).
v3: Add kernel 3.5/3.4 comment.
v4: Fix compilation warnings.
Signed-off-by: Jerome Glisse <jglisse@redhat.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
drm/radeon: do not reenable crtc after moving vram start address
It seems we can not update the crtc scanout address. After disabling
crtc, update to base address do not take effect after crtc being
reenable leading to at least frame being scanout from the old crtc
base address. Disabling crtc display request lead to same behavior.
So after changing the vram address if we don't keep crtc disabled
we will have the GPU trying to read some random system memory address
with some iommu this will broke the crtc engine and will lead to
broken display and iommu error message.
So to avoid this, disable crtc. For flicker less boot we will need
to avoid moving the vram start address.
projects / ~andy / linux / log