Since there are only 32 (64) distinct color values for each color
in 16bpp Matrox hardware expects those in a 'dense' manner, ie in
the first 32 (64) entries of the respective color.
Signed-off-by: Egbert Eich <eich@suse.de> Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Mon, 29 Jul 2013 23:43:28 +0000 (09:43 +1000)]
Merge branch 'drm-fixes-3.11' of git://people.freedesktop.org/~agd5f/linux
Alex writes:
A few more radeon bug fixes, mostly for SI dpm. At this point dpm is
pretty solid across the majority of asics. I think we mostly just have
corner cases and fixing up some of the trickier features at this point.
* 'drm-fixes-3.11' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon/dpm: fix and enable reclocking on SI
drm/radeon/dpm: disable cac setup on SI
drm/radeon/si: disable cgcg and pg for now
drm/radeon/dpm: fix forcing performance state to low on cayman
drm/radeon/atom: fix fb when fetching engine params
drm/radeon: properly handle cg on asics without UVD
drm/radeon/dpm: fix powertune handling for pci id 0x6835
drm/radeon/dpm: fix si_calculate_memory_refresh_rate()
drm/radeon/dpm: fix display gap programming on SI
drm/radeon: fix audio dto programming on DCE4+
cpufreq: Fix cpufreq driver module refcount balance after suspend/resume
Since cpufreq_cpu_put() called by __cpufreq_remove_dev() drops the
driver module refcount, __cpufreq_remove_dev() causes that refcount
to become negative for the cpufreq driver after a suspend/resume
cycle.
This is not the only bad thing that happens there, however, because
kobject_put() should only be called for the policy kobject at this
point if the CPU is not the last one for that policy.
Namely, if the given CPU is the last one for that policy, the
policy kobject's refcount should be 1 at this point, as set by
cpufreq_add_dev_interface(), and only needs to be dropped once for
the kobject to go away. This actually happens under the cpu == 1
check, so it need not be done before by cpufreq_cpu_put().
On the other hand, if the given CPU is not the last one for that
policy, this means that cpufreq_add_policy_cpu() has been called
at least once for that policy and cpufreq_cpu_get() has been
called for it too. To balance that cpufreq_cpu_get(), we need to
call cpufreq_cpu_put() in that case.
Thus, to fix the described problem and keep the reference
counters balanced in both cases, move the cpufreq_cpu_get() call
in __cpufreq_remove_dev() to the code path executed only for
CPUs that share the policy with other CPUs.
Reported-and-tested-by: Toralf Förster <toralf.foerster@gmx.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com> Cc: 3.10+ <stable@vger.kernel.org>
Alex Deucher [Sun, 28 Jul 2013 22:26:38 +0000 (18:26 -0400)]
drm/radeon/dpm: disable cac setup on SI
Disable cac setup on SI for now since it causes
strange performance level restrictions on certain
cards. I suspect there may be issues with some of
the 64 bit fixed point double emulation that is used
to set up those parameters. I need to double check
the math before this can be re-enabled.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Mon, 29 Jul 2013 15:51:25 +0000 (11:51 -0400)]
drm/radeon/si: disable cgcg and pg for now
Coarse grain clockgating causes problems with reclocking on
some cards and powergating (verde only) causes problems with
ring initialization. The proper fix (restructuring the init
sequences) is too invasive for 3.11 so just disable them for
now.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
USB: serial: ftdi_sio: add more RT Systems ftdi devices
RT Systems makes many usb serial cables based on the ftdi_sio driver for
programming various amateur radios. This patch is a full listing of
their current product offerings and should allow these cables to all
be recognized.
Since we clear QUEUE_STARTED in rt2x00queue_stop_queue(), following
call to rt2x00queue_pause_queue() reduce to noop, i.e we do not
stop queue in mac80211.
To fix that introduce rt2x00queue_pause_queue_nocheck() function,
which will stop queue in mac80211 directly.
Note that rt2x00_start_queue() explicitly set QUEUE_PAUSED bit.
Note also that reordering operations i.e. first call to
rt2x00queue_pause_queue() and then clear QUEUE_STARTED bit, will race
with rt2x00queue_unpause_queue(), so calling ieee80211_stop_queue()
directly is the only available solution to fix the problem without
major rework.
Cc: stable@vger.kernel.org Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl> Signed-off-by: John W. Linville <linville@tuxdriver.com>
We simplified the rules to recognise each classification of recoverable
machine check combining the instruction and data fetch rules into a
single entry based on clarifications in the June 2013 SDM that all
recoverable events would be reported on the unaffected processor with
MCG_STATUS.EIPV=0 and MCG_STATUS.RIPV=1. Unfortunately the simplified
rule has a couple of bugs. Fix them here.
Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Signed-off-by: Tony Luck <tony.luck@intel.com>
usb: chipidea: cast PORTSC_PTS and DEVLC_PTS macros
Fix the following build warnings on x86:
drivers/usb/chipidea/core.c: In function 'hw_phymode_configure':
drivers/usb/chipidea/core.c:226:3: warning: large integer implicitly truncated to unsigned type [-Woverflow]
drivers/usb/chipidea/core.c:230:3: warning: large integer implicitly truncated to unsigned type [-Woverflow]
drivers/usb/chipidea/core.c:243:3: warning: large integer implicitly truncated to unsigned type [-Woverflow]
drivers/usb/chipidea/core.c:246:3: warning: large integer implicitly truncated to unsigned type [-Woverflow]
Reported-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes all MODULE_DEVICE_TABLE declarations.
Exynos drm drivers don't need to create MODULE_DEVICE_TABLE
yet because all devices of Exynos drm include in one SoC so
they cannot be plugged in as of now.
Signed-off-by: Inki Dae <inki.dae@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
drm/exynos: exynos_drm_ipp: fix return value check
In case of error, the function ipp_find_obj() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check
should be replaced with IS_ERR().
Mark Brown [Mon, 29 Jul 2013 07:50:28 +0000 (08:50 +0100)]
ASoC: bfin-ac97: Fix prototype error following AC'97 refactoring
As part of the multiplatform refactoring for AC'97 the AC'97 bus ops were
staticised meaning that the prototype (which was never needed) conflicts
with the declaration causing build failures.
Signed-off-by: Mark Brown <broonie@linaro.org> Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Merge tag 'fixes-for-v3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v3.11-rc3
Here are some fixes for v3.11-rc3. Mostly related to
the recent conversion to configfs done on the gadget
drivers, but we also have a fix for MUSB resources
on platforms which need 3 resources instead of 2, and
a fix for the sysfs_notify() call on udc-core.c which
was notifying an unexistent file.
ALSA: compress: fix the return value for SNDRV_COMPRESS_VERSION
the return value of SNDRV_COMPRESS_VERSION always return default -ENOTTY as the
return value was never updated for this call
assign return value from put_user()
Revert "cpuidle: Quickly notice prediction failure for repeat mode"
Revert commit 69a37bea (cpuidle: Quickly notice prediction failure for
repeat mode), because it has been identified as the source of a
significant performance regression in v3.8 and later as explained by
Jeremy Eder:
We believe we've identified a particular commit to the cpuidle code
that seems to be impacting performance of variety of workloads.
The simplest way to reproduce is using netperf TCP_RR test, so
we're using that, on a pair of Sandy Bridge based servers. We also
have data from a large database setup where performance is also
measurably/positively impacted, though that test data isn't easily
share-able.
Included below are test results from 3 test kernels:
kernel reverts
-----------------------------------------------------------
1) vanilla upstream (no reverts)
The below data are histograms representing the %c0 residency @
1-second sample rates (using turbostat), while under netperf test.
- If you look at the first 4 histograms, you can see %c0 residency
almost entirely in the 30,40% bin.
- The last pair, which reverts 69a37beabf1f0a6705c08e879bdd5d82ff6486c4,
shows %c0 in the 80,90,100% bins.
Below each kernel name are netperf TCP_RR trans/s numbers for the
particular kernel that can be disclosed publicly, comparing the 3
test kernels. We ran a 4th test with the vanilla kernel where
we've also set /dev/cpu_dma_latency=0 to show overall impact
boosting single-threaded TCP_RR performance over 11% above
baseline.
These results demonstrate gaining back the tendency of the CPU to
stay in more responsive, performant C-states (and thus yield
measurably better performance), by reverting commit 69a37beabf1f0a6705c08e879bdd5d82ff6486c4.
Requested-by: Jeremy Eder <jeder@redhat.com> Tested-by: Len Brown <len.brown@intel.com> Cc: 3.8+ <stable@vger.kernel.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Revert "cpuidle: Quickly notice prediction failure in general case"
Revert commit e11538d1 (cpuidle: Quickly notice prediction failure in
general case), since it depends on commit 69a37be (cpuidle: Quickly
notice prediction failure for repeat mode) that has been identified
as the source of a significant performance regression in v3.8 and
later.
Requested-by: Jeremy Eder <jeder@redhat.com> Tested-by: Len Brown <len.brown@intel.com> Cc: 3.8+ <stable@vger.kernel.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Johan Hedberg [Sat, 27 Jul 2013 19:11:14 +0000 (14:11 -0500)]
Bluetooth: Fix calling request callback more than once
In certain circumstances, such as an HCI driver using __hci_cmd_sync_ev
with HCI_EV_CMD_COMPLETE as the expected completion event there is the
chance that hci_event_packet will call hci_req_cmd_complete twice (once
for the explicitly looked after event and another time in the actual
handler of cmd_complete).
In the case of __hci_cmd_sync_ev this introduces a race where the first
call wakes up the blocking __hci_cmd_sync_ev and lets it complete.
However, by the time that a second __hci_cmd_sync_ev call is already in
progress the second hci_req_cmd_complete call (from the previous
operation) will wake up the blocking function prematurely and cause it
to fail, as witnessed by the following log:
Rong Wang [Sun, 28 Jul 2013 15:01:35 +0000 (23:01 +0800)]
usb: gadget: udc-core: fix the typo of udc state attribute
The name of udc state attribute file under sysfs is registered as
"state", while usb_gadget_set_state take it as "status" when it's
going to update. This patch fixes the typo.
Signed-off-by: Rong Wang <Rong.Wang@csr.com> Signed-off-by: Barry Song <Baohua.Song@csr.com> Cc: <stable@kernel.org> Signed-off-by: Felipe Balbi <balbi@ti.com>
The compatibility layer which the USBF_PHONET_INCLUDED was a part of
is no longer present - the USBF_PHONET_INCLUDED is not #defined by anyone
anymore, so the ifndef is always true. Removing it.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: gadget: multi: fix error return code in cdc_do_config()
Fix to return a negative error code from the error handling
case instead of 0, as returned elsewhere in this function.
Introduced by commit 59835a (usb: gadget: multi: use
function framework for ACM.)
Make rndis_do_config() consistent with cdc_do_config() in the way it
handles returning the PTR_ERR(f_acm_*).
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Johan Hedberg [Tue, 23 Jul 2013 23:32:46 +0000 (02:32 +0300)]
Bluetooth: Fix HCI init for BlueFRITZ! devices
None of the BlueFRITZ! devices with manufacurer ID 31 (AVM Berlin)
support HCI_Read_Local_Supported_Commands. It is safe to use the
manufacturer ID (instead of e.g. a USB ID specific quirk) because the
company never created any newer controllers.
Dan Carpenter [Tue, 2 Jul 2013 06:28:21 +0000 (09:28 +0300)]
fbdev/atyfb: fix recent breakage in correct_chipset()
The 6e36308a6f "fb: fix atyfb build warning" isn't right. It makes all
the indexes off by one. This patch reverts it and casts the
ARRAY_SIZE() to int to silence the build warning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Merge tag 'pinctrl-for-v3.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
- Driver fixes for AM33xx, SIRF and PFC pin controllers
- Fix a compile warning from the pinctrl single-register driver
- Fix a little nasty memory leak
* tag 'pinctrl-for-v3.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: fix a memleak when freeing maps
pinctrl: pinctrl-single: fix compile warning when no CONFIG_PM
pinctrl: sh-pfc: fix SDHI0 VccQ regulator on sh73a0 with DT
arm/dts: sirf: fix the pingroup name mismatch between drivers and dts
pinctrl: sirf: add usp0_uart_nostreamctrl pin group for usp-uart without flowctrl
pinctrl: sirf: fix the pin number and mux bit for usp0
pinctrl: am33xx dt binding: correct include path
Merge tag 'trace-fixes-3.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Oleg is working on fixing a very tight race between opening a event
file and deleting that event at the same time (both must be done as
root).
I also found a bug while testing Oleg's patches which has to do with a
race with kprobes using the function tracer.
There's also a deadlock fix that was introduced with the previous
fixes"
* tag 'trace-fixes-3.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Remove locking trace_types_lock from tracing_reset_all_online_cpus()
ftrace: Add check for NULL regs if ops has SAVE_REGS set
tracing: Kill trace_cpu struct/members
tracing: Change tracing_fops/snapshot_fops to rely on tracing_get_cpu()
tracing: Change tracing_entries_fops to rely on tracing_get_cpu()
tracing: Change tracing_stats_fops to rely on tracing_get_cpu()
tracing: Change tracing_buffers_fops to rely on tracing_get_cpu()
tracing: Change tracing_pipe_fops() to rely on tracing_get_cpu()
tracing: Introduce trace_create_cpu_file() and tracing_get_cpu()
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is five bug fixes, two of which fix long standing problems
causing crashes (sd and mvsas). The remaining three are hung (isci
race) or lost (qla2xxx, isci) devices"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] isci: fix breakage caused by >16byte CDB patch
[SCSI] mvsas: Fix kernel panic on tile due to unaligned data access
[SCSI] sd: fix crash when UA received on DIF enabled device
[SCSI] qla2xxx: Properly set the tagging for commands.
[SCSI] isci: Fix a race condition in the SSP task management path
Emil Tantilov [Fri, 26 Jul 2013 12:46:36 +0000 (05:46 -0700)]
igb: fix vlan filtering in promisc mode when not in VT mode
This patch fixes a VT mode check to make sure VLAN filters are disabled when
in promisc mode and VT is not enabled.
The problem with the previous check was that:
E1000_MRQC_ENABLE_VMDQ is defined as 0x00000003
but when not in VT mode:
mrqc |= E1000_MRQC_ENABLE_RSS_4Q (0x00000002)
So the above check will trigger regardless if VT mode is being used or not.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes an issue with the 82598EB device, where lldpad is causing Tx
Hangs on the card as soon as it attempts to configure DCB for the device. The
adapter will continually Tx hang and reset in a loop.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Cc: Stable <stable@vger.kernel.org> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Tested-by: Jack Morgan <jack.morgan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hovold [Sat, 27 Jul 2013 11:34:42 +0000 (13:34 +0200)]
USB: mos7840: fix pointer casts
Silence compiler warnings on 64-bit systems introduced by commit 05cf0dec ("USB: mos7840: fix race in led handling") which uses the
usb-serial data pointer to temporarily store the device type during
probe but failed to add the required casts.
[gregkh - change uintptr_t to unsigned long]
Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allocate a descriptor for each period of a cyclic transfer, not just the first.
Also since the callback needs to be called for each finished period make sure to
initialize the callback and callback_param fields of each descriptor in a cyclic
transfer.
genetlink: release cb_lock before requesting additional module
Requesting external module with cb_lock taken can result in
the deadlock like showed below:
[ 2458.111347] Showing all locks held in the system:
[ 2458.111347] 1 lock held by NetworkManager/582:
[ 2458.111347] #0: (cb_lock){++++++}, at: [<ffffffff8162bc79>] genl_rcv+0x19/0x40
[ 2458.111347] 1 lock held by modprobe/603:
[ 2458.111347] #0: (cb_lock){++++++}, at: [<ffffffff8162baa5>] genl_lock_all+0x15/0x30
Problem start to happen after adding net-pf-16-proto-16-family-nl80211
alias name to cfg80211 module by below commit (though that commit
itself is perfectly fine):
nl80211: Add generic netlink module alias for cfg80211/nl80211
Reported-and-tested-by: Jeff Layton <jlayton@redhat.com> Reported-by: Richard W.M. Jones <rjones@redhat.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Reviewed-by: Pravin B Shelar <pshelar@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Frank Li [Thu, 25 Jul 2013 06:05:53 +0000 (14:05 +0800)]
net: fec: workaround stop tx during errata ERR006358
If the ready bit in the transmit buffer descriptor (TxBD[R])
is previously detected as not set during a prior frame transmission,
then the ENET_TDAR[TDAR] bit is cleared at a later time, even if
additional TxBDs were added to the ring and the ENET_TDAR[TDAR]
bit is set. This results in frames not being transmitted until
there is a 0-to-1 transition on ENET_TDAR[TDAR].
Workarounds:
code can use the transmit frame interrupt flag (ENET_EIR[TXF])
as a method to detect whether the ENET has completed transmission
and the ENET_TDAR[TDAR] has been cleared. If ENET_TDAR[TDAR] is
detected as cleared when packets are queued and waiting for transmit,
then a write to the TDAR bit will restart TxBD processing.
This case main happen when loading is light. A ethernet package may
not send out utile next package put into tx queue.
How to test:
while [ true ]
do
ping <IP> -s 10000 -w 4
ping <IP> -s 6000 -w 2
ping <IP> -s 4000 -w 2
ping <IP> -s 10000 -w 2
done
You will see below result in overnight test.
6008 bytes from 10.192.242.116: seq=1 ttl=128 time=0.722 ms
4008 bytes from 10.192.242.116: seq=0 ttl=128 time=1001.008 ms
4008 bytes from 10.192.242.116: seq=1 ttl=128 time=1.010 ms
10008 bytes from 10.192.242.116: seq=0 ttl=128 time=0.896 ms
After apply this patch, >1000ms delay disappear.
Signed-off-by: Frank Li <Frank.Li@freescale.com> Acked-by: Fugang Duan <B38611@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
qlcnic: Fix diagnostic interrupt test for 83xx adapters.
o Initialize proper interrupt handler for 83xx.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
o When configuring guest VLAN after PVID configuration, VF was loading
with previously configured PVID. Clear the PVID which was previously
configured before configuring guest VLAN.
o Display guest VLAN when it is configured
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Operation type and command type is not set correct in back channel
response.
Signed-off-by: Pratik Pujar <pratik.pujar@qlogic.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Work function needs to be initialized before we participate in
inter device communication (IDC).
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Clemens Ladisch [Mon, 22 Jul 2013 19:32:09 +0000 (21:32 +0200)]
firewire: fix libdc1394/FlyCap2 iso event regression
Commit 18d627113b83 (firewire: prevent dropping of completed iso packet
header data) was intended to be an obvious bug fix, but libdc1394 and
FlyCap2 depend on the old behaviour by ignoring all returned information
and thus not noticing that not all packets have been received yet. The
result was that the video frame buffers would be saved before they
contained the correct data.
Reintroduce the old behaviour for old clients.
Tested-by: Stepan Salenikovich <stepan.salenikovich@gmail.com> Tested-by: Josep Bosch <jep250@gmail.com> Cc: <stable@vger.kernel.org> # 3.4+ Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Uwe Kleine-König [Fri, 28 Jun 2013 09:49:41 +0000 (11:49 +0200)]
serial/mxs-auart: increase time to wait for transmitter to become idle
Without this patch the driver waits ~1 ms for the UART to become idle. At
115200n8 this time is (theoretically) enough to transfer 11.5 characters
(= 115200 bits/s / (10 Bits/char) * 1ms). As the mxs-auart has a fifo size
of 16 characters the clock is gated too early. The problem is worse for
lower baud rates.
This only happens to really shut down the transmitter in the middle of a
transfer if /dev/ttyAPPx isn't opened in userspace (e.g. by a getty) but
was at least once (because the bootloader doesn't disable the transmitter).
So increase the timeout to 20 ms which should be enough for 9600n8, too.
Moreover skip gating the clock if the timeout is elapsed.
serial/mxs-auart: fix race condition in interrupt handler
The handler needs to ack the pending events before actually handling them.
Otherwise a new event might come in after it it considered non-pending or
handled and is acked then without being handled. So this event is only
noticed when the next interrupt happens.
Without this patch an i.MX28 based machine running an rt-patched kernel
regularly hangs during boot.
Neil Horman [Fri, 26 Jul 2013 16:47:14 +0000 (12:47 -0400)]
atl1c: Fix misuse of netdev_alloc_skb in refilling rx ring
atl1c uses netdev_alloc_skb to refill its rx dma ring, but that call makes no
guarantees about the suitability of the memory for use in DMA. As a result
we've gotten reports of atl1c drivers occasionally hanging and needing to be
reset:
https://bugzilla.kernel.org/show_bug.cgi?id=54021
Fix this by modifying the call to use the internal version __netdev_alloc_skb,
where you can set the gfp_mask explicitly to include GFP_DMA.
Tested by two reporters in the above bug, who have the hardware to validate it.
Both report immediate cessation of the problem with this patch
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> CC: Jay Cliburn <jcliburn@gmail.com> CC: "David S. Miller" <davem@davemloft.net> CC: stable@vger.kernel.org Tested-by: Luis Henriques <luis.henriques@canonical.com> Tested-by: Vincent Alquier <vincent.alquier@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"This is just a regular fixes pull apart from the qxl one, it has
radeon and intel bits in it,
The intel fixes are for a regression with the RC6 fix and a 3.10 hdmi
regression, whereas radeon is more DPM fixes, a few lockup fixes and
some rn50/r100 DAC fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/dpm: fix r600_enable_sclk_control()
drm/radeon/dpm: implement force performance levels for rv6xx
drm/radeon/dpm: fix displaygap programming on rv6xx
drm/radeon/dpm: fix a typo in the rv6xx mclk setup
drm/i915: initialize gt_lock early with other spin locks
drm/i915: fix hdmi portclock limits
drm/radeon: fix combios tables on older cards
drm/radeon: improve dac adjust heuristics for legacy pdac
drm/radeon: Another card with wrong primary dac adj
drm/radeon: fix endian issues with DP handling (v3)
drm/radeon/vm: only align the pt base to 32k
drm/radeon: wait for 3D idle before using CP DMA
Merge branch 'qxl-fixes' of git://people.freedesktop.org/~airlied/linux
Pull qxl drm fixes from Dave Airlie:
"Okay as I warned, the qxl driver was running a bit free and loose with
its ttm object reservations and the new lockdep enabled reservation
tracking shone a bright light into it, it also with the new
reservations mutexes hits a possible deadlock during boot.
The first patch is a real fix to render the console correctly as the
driver used to just drop irq renderering as too hard, this also fixes
a sleeping while atomic warning.
The other two patches are the big ugly ones that redo how the driver
allocates objects and reserves them and makes things all work
properly, I've tested this in a VM, and compared to the current code
which hits a lockdep warning and the sleep while atomic warning before
failing.
So sorry this is coming in late, I should have tested qxl before
merging the mutex code, but I'd rather just fix qxl with this than
revert the reservations code at this point"
* 'qxl-fixes' of git://people.freedesktop.org/~airlied/linux:
qxl: convert qxl driver to proper use for reservations
qxl: allow creation of pre-pinned objects and use for releases.
drm/qxl: add delayed fb operations
Merge tag 'pm+acpi-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"These are just two fixes, a revert of the would-be backlight fix that
didn't work and an intel_pstate fix for two problems related to
maximum P-state selection.
Specifics:
- Revert of the ACPI video commit that I hoped would help fix
backlight problems related to Windows 8 compatibility on some
systems. Unfortunately, it turned out to cause problems to happen
too.
- Fix for two problems in intel_pstate, a possible failure to respond
to a load change on a quiet system and a possible failure to select
the highest available P-state on some systems. From Dirk
Brandewie"
* tag 'pm+acpi-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "ACPI / video / i915: No ACPI backlight if firmware expects Windows 8"
cpufreq / intel_pstate: Change to scale off of max P-state
Reported-by: Wei Yang <weiyang@linux.vnet.ibm.com> Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com> Acked-by: Nithin Nayak Sujir <nsujir@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
While EEH error happens, we might not have network device instance
(struct net_device) yet. So we can't access the instance safely and
check its link state, which causes kernel crash. The patch fixes it.
Reported-by: Wei Yang <weiyang@linux.vnet.ibm.com> Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com> Acked-by: Nithin Nayak Sujir <nsujir@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Francesco Fusco [Wed, 24 Jul 2013 08:39:07 +0000 (10:39 +0200)]
sysctl: range checking in do_proc_dointvec_ms_jiffies_conv
When (integer) sysctl values are expressed in ms and have to be
represented internally as jiffies. The msecs_to_jiffies function
returns an unsigned long, which gets assigned to the integer.
This patch prevents the value to be assigned if bigger than
INT_MAX, done in a similar way as in cba9f3 ("Range checking in
do_proc_dointvec_(userhz_)jiffies_conv").
Signed-off-by: Francesco Fusco <ffusco@redhat.com> CC: Andrew Morton <akpm@linux-foundation.org> CC: linux-kernel@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
Francesco Fusco [Wed, 24 Jul 2013 08:39:06 +0000 (10:39 +0200)]
neigh: prevent overflowing params in /proc/sys/net/ipv4/neigh/
Without this patch, the fields app_solicit, gc_thresh1, gc_thresh2,
gc_thresh3, proxy_qlen, ucast_solicit, mcast_solicit could have
assumed negative values when setting large numbers.
Signed-off-by: Francesco Fusco <ffusco@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hovold [Fri, 26 Jul 2013 09:55:19 +0000 (11:55 +0200)]
USB: mos7840: fix race in led handling
Fix race in LED handling introduced by commit 0eafe4de ("USB: serial:
mos7840: add support for MCS7810 devices") which reused the port control
urb for manipulating the LED without making sure that the urb is not
already in use. This could lead to the control urb being manipulated
while in flight.
Fix by adding a dedicated LED urb and ctrlrequest along with a LED-busy
flag to handle concurrency.
Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Fri, 26 Jul 2013 09:55:18 +0000 (11:55 +0200)]
USB: mos7840: fix device-type detection
Fix race in device-type detection introduced by commit 0eafe4de ("USB:
serial: mos7840: add support for MCS7810 devices") which used a static
variable to hold the device type.
Move type detection to probe and use serial data to store the device
type.
Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: serial: add driver for Suunto ANT+ USB device
This adds a driver for the Suunto ANT+ USB device, exposing it as a usb
serial device. This lets the userspace "gant" program to talk to the
device to communicate over the ANT+ protocol to any devices it finds.
When the device is physically connected the driver sends a disassoc
command to the device and response triggers the driver to inform cfg80211
about it. However, with the device removed the disassoc command fails.
This patch adds a call to cfg80211_disconnected() when that command fails.
The warning was added by commit below and also cleans up, but better
doing it in the driver if only to get rid of the warning.
wireless: check for dangling wdev->current_bss pointer
Cc: Ben Greear <greearb@candelatech.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomasz Moń [Tue, 23 Jul 2013 05:42:49 +0000 (07:42 +0200)]
mwifiex: Add missing endian conversion.
Both type and pkt_len variables are in host endian and these should be in
Little Endian in the payload.
Signed-off-by: Tomasz Moń <desowin@gmail.com> Acked-by: Bing Zhao <bzhao@marvell.com> Cc: <stable@vger.kernel.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eric Dumazet [Wed, 24 Jul 2013 00:15:54 +0000 (17:15 -0700)]
usbnet: do not pretend to support SG/TSO
usbnet doesn't support yet SG, so drivers should not advertise SG or TSO
capabilities, as they allow TCP stack to build large TSO packets that
need to be linearized and might use order-5 pages.
This adds an extra copy overhead and possible allocation failures.
Current code ignore skb_linearize() return code so crashes are even
possible.
Best is to not pretend SG/TSO is supported, and add this again when/if
usbnet really supports SG for devices who could get a performance gain.
Based on a prior patch from Freddy Xin <freddy@asix.com.tw>
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge tag 'arm64-stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64
Pull arm64 fixes from Catalin Marinas:
- Stack size increased to 16K (similar to other 64-bit architectures)
- Additional cache flushing for secondary CPUs boot mode
* tag 'arm64-stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
arm64: Change kernel stack size to 16K
arm64: Fix definition of arm_pm_restart to match the declaration
arm64: virt: ensure visibility of __boot_cpu_mode
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"This is a largeish batch of fixes, mostly because I missed -rc2 due to
travel/vacation. So in number these are a bit more than ideal unless
you amortize them over two -rcs.
Quick breakdown:
- Defconfig updates
- Making multi_v7_defconfig useful on more hardware to encourage
single-image usage
- Davinci and nomadik updates due to new code merged this merge
window
- Fixes for UART on Samsung platforms, both PM and clock-related
- A handful of warning fixes from defconfig builds, including for
max8925 backlight and pxamci (both with appropriate acks)
- Exynos5440 fixes for LPAE configuration, PM
- ...plus a bunch of other smaller changes all over the place
I expect to switch to regressions-or-severe-bugs-only fixes from here
on out"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (37 commits)
mfd: max8925: fix dt code for backlight
ARM: omap5: Only select errata 798181 if SMP
ARM: EXYNOS: Update CONFIG_ARCH_NR_GPIO for Exynos
ARM: EXYNOS: Fix low level debug support
ARM: SAMSUNG: Save/restore only selected uart's registers
ARM: SAMSUNG: Add SAMSUNG_PM config option to select pm
ARM: S3C24XX: Add missing clkdev entries for s3c2440 UART
ARM: multi_v7_defconfig: Select USB chipidea driver
ARM: pxa: propagate errors from regulator_enable() to pxamci
ARM: zynq: fix compilation warning
ARM: keystone: fix compilation warning
ARM: highbank: Only touch common coherency control register fields
ARM: footbridge: fix overlapping PCI mappings
dmaengine: shdma: fix a build failure on platforms with no DMA support
ARM: STi: Set correct ARM ERRATAs.
ARM: dts: STi: Fix pinconf setup for STiH416 serial2
ARM: nomadik: configure for NO_HZ and HRTIMERS
ARM: nomadik: update defconfig base
ARM: nomadik: Update MMC defconfigs
ARM: davinci: defconfig: enable EDMA driver
...
Merge tag 'usb-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of USB fixes for 3.11-rc3.
Lots of little things, nothing major. A number of new device ids,
build fixes for DMA, and a bunch of other minor things. All of these
have been in the linux-next tree"
* tag 'usb-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (40 commits)
usb: Clear both buffers when clearing a control transfer TT buffer.
usb/gadget: free opts struct on error recovery
USB: mos7840: fix memory leak in open
usb: serial: option.c: remove ONDA MT825UP product ID fromdriver
usb: serial: option: add Olivetti Olicard 200
usb: serial: option: blacklist ONDA MT689DC QMI interface
xhci: fix null pointer dereference on ring_doorbell_for_active_rings
usb: host: xhci: Enable XHCI_SPURIOUS_SUCCESS for all controllers with xhci 1.0
usb: fix build warning in pci-quirks.h when CONFIG_PCI is not enabled
usb: xhci: Mark two functions __maybe_unused
xhci: Avoid NULL pointer deref when host dies.
usb: serial: option: Add ONYX 3G device support
USB: ti_usb_3410_5052: fix dynamic-id matching
usb: option: add TP-LINK MA260
USB: option: add D-Link DWM-152/C1 and DWM-156/C1
USB: EHCI: Fix resume signalling on remote wakeup
USB: cp210x: add MMB and PI ZigBee USB Device Support
usb: cp210x support SEL C662 Vendor/Device
USB: option: append Petatel NP10T device to GSM modems list
USB: misc: Add Manhattan Hi-Speed USB DVI Converter to sisusbvga
...
Merge tag 'tty-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are 3 fixes for TTY and serial issues that have been reported.
Nothing huge, but nice to get fixed"
* tag 'tty-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: tegra: correct help message in Kconfig from 'ttyHS' to 'ttyTHS'
tty/8250_early: Don't truncate last character of options
TTY: snyclinkmp: calculating wrong addresses
Merge tag 'staging-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging fixes from Greg KH:
"Here are some tiny drivers/staging/ fixes for 3.11-rc3
A number of bugfixes, all pretty tiny, but resolve issues that have
been reported (the kstrtos32 change fixes a data corruption problem
that Dan found). And a MAINTAINERS file update for the comedi
drivers"
* tag 'staging-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
MAINTAINERS: Update the list of maintainers for staging/comedi driver.
staging: tidspbridge: replace strict_strtol() with kstrtos32()
staging: android: logger: Correct write offset reset on error
staging: zram: protect zram_reset_device() call
staging: gdm72xx: potential use after free in send_qos_list()
staging: drm/imx: drop "select OF_VIDEOMODE"
staging: frontier: use after free in disconnect()
staging: comedi: fix a race between do_cmd_ioctl() and read/write
staging: comedi: COMEDI_CANCEL ioctl should wake up read/write
Merge tag 'char-misc-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc patches from Greg KH:
"Here are some char/misc patches for 3.11-rc3. It's pretty much just:
- mei fixes
- hyperv fixes
- new ja_JP translation update
all tiny stuff, but fixes for issues people have reported."
* tag 'char-misc-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
HOWTO ja_JP sync
mei: me: fix waiting for hw ready
mei: don't have to clean the state on power up
mei: me: fix reset state machine
mei: hbm: fix typo in error message
Tools: hv: KVP: Fix a bug in IPV6 subnet enumeration
Drivers: hv: balloon: Do not post pressure status if interrupted
Drivers: hv: balloon: Fix a bug in the hot-add code
Drivers: hv: vmbus: incorrect device name is printed when child device is unregistered
Merge tag 'sound-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Just a handful of regression and small fixes in ASoC, HD-audio and
USB-audio drivers.
- Sigmetal HD-audio codec regression fixes
- A copule of XRUN indication fixes for usb-audio devices
- ASoC: ep93xx build fix, sgtl5000 fix for probe order changes,
max98088 register access fix, etc"
* tag 'sound-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hiface: return correct XRUN indication
ASoC: tegra: correct playback_dma_data setup
ASoC: core: double free in snd_soc_add_platform()
ALSA: usb-audio: 6fire: return correct XRUN indication
ASoC: ep93xx: fix build of ep93xx-ac97.c
ALSA: hda - Remove NO_PRESENCE bit override for Dell 1420n Laptop
ALSA: hda - Fix EAPD GPIO control for Sigmatel codecs
ASoC: atmel-ssc: remove clk_disable_unprepare call from critical section
ASoC: sgtl5000: defer the probe if clock is not found
ASoC: max98088 - fix element type of the register cache.
Merge tag 'for-linus-v3.11-rc3' of git://oss.sgi.com/xfs/xfs
Pull xfs fix from Ben Myers:
"Fix for regression in commit cca9f93a52d2 ("xfs: don't do IO when
creating an new inode"), recovery causing filesystem corruption after
a crash"
* tag 'for-linus-v3.11-rc3' of git://oss.sgi.com/xfs/xfs:
xfs: di_flushiter considered harmful
Merge branch 'for-3.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"Assorted libata updates.
The most critical one is a fix for ahci oops during boot. Also, a new
smallish platform ahci driver is added and sata_inic162x is marked
clearly as experimental (it whines during boot too) as data corruption
seems rather common on the device and it's unlikely to get any love in
the foreseeable future. If the whining doesn't draw any attention, I
think we'd probably be better of making the driver depend on BROKEN in
a couple releases"
This is v2 of this pull request with fixed dependencies for ahci_imx.
* 'for-3.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci_imx: depend on CONFIG_MFD_SYSCON
ahci_imx: add ahci sata support on imx platforms
ARM: imx6q: update the sata bits definitions of gpr13
ahci: fix Null pointer dereference in achi_host_active()
libata: make it clear that sata_inic162x is experimental
libata: replace strict_strtol() with kstrtol()
ata: Fix DVD not dectected at some platform with Wellsburg PCH
Yinghai Lu [Thu, 25 Jul 2013 13:31:38 +0000 (06:31 -0700)]
PCI: Retry allocation of only the resource type that failed
Ben Herrenschmidt reported the following problem:
- The bus has space for all desired MMIO resources, including optional
space for SR-IOV devices
- We attempt to allocate I/O port space, but it fails because the bus
has no I/O space
- Because of the I/O allocation failure, we retry MMIO allocation,
requesting only the required space, without the optional SR-IOV space
This means we don't allocate the optional SR-IOV space, even though we
could.
This is related to 0c5be0cb0e ("PCI: Retry on IORESOURCE_IO type
allocations").
This patch changes how we handle allocation failures. We will now retry
allocation of only the resource type that failed. If MMIO allocation
fails, we'll retry only MMIO allocation. If I/O port allocation fails,
we'll retry only I/O port allocation.
Revert "ACPI / video / i915: No ACPI backlight if firmware expects Windows 8"
We attempted to address a regression introduced by commit a57f7f9
(ACPICA: Add Windows8/Server2012 string for _OSI method.) after which
ACPI video backlight support doesn't work on a number of systems,
because the relevant AML methods in the ACPI tables in their BIOSes
become useless after the BIOS has been told that the OS is compatible
with Windows 8. That problem is tracked by the bug entry at:
https://bugzilla.kernel.org/show_bug.cgi?id=51231
Commit 8c5bd7a (ACPI / video / i915: No ACPI backlight if firmware
expects Windows 8) introduced for this purpose essentially prevented
the ACPI backlight support from being used if the BIOS had been told
that the OS was compatible with Windows 8 and the i915 driver was
loaded, in which case the backlight would always be handled by i915.
Unfortunately, however, that turned out to cause problems with
backlight to appear on multiple systems with symptoms indicating that
i915 was unable to control the backlight on those systems as
expected.
For this reason, revert commit 8c5bd7a, but leave the function
acpi_video_backlight_quirks() introduced by it, because another
commit on top of it uses that function.
References: https://lkml.org/lkml/2013/7/21/119
References: https://lkml.org/lkml/2013/7/22/261
References: https://lkml.org/lkml/2013/7/23/429
References: https://lkml.org/lkml/2013/7/23/459
References: https://lkml.org/lkml/2013/7/23/81
References: https://lkml.org/lkml/2013/7/24/27 Reported-and-tested-by: James Hogan <james@albanarts.com> Reported-and-tested-by: Kamal Mostafa <kamal@canonical.com> Reported-and-tested-by: Jörg Otte <jrg.otte@gmail.com> Reported-and-tested-by: Steven Newbury <steve@snewbury.org.uk> Reported-by: Martin Steigerwald <Martin@lichtvoll.de> Reported-by: Kalle Valo <kvalo@adurom.com> Tested-by: Joerg Platte <jplatte@naasa.net> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ahci_imx makes use of regmap but the dependency wasn't specified in
Kconfig leading build failures if CONFIG_AHCI_IMX is enabled but
CONFIG_MFD_SYSCON is not. Add the Kconfig dependency.
Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
projects / ~andy / linux / log