Hans Verkuil [Thu, 12 Dec 2013 10:35:22 +0000 (07:35 -0300)]
[media] sn9c102: prepare for removal by moving it to staging
During the last media summit meeting it was decided to move this driver to
staging as the first step to removing it altogether.
Most webcams covered by this driver are now supported by gspca. Nobody has the
hardware to convert the remaining devices to gspca.
This driver needs a major overhaul to have it conform to the latest frameworks
and compliancy tests.
Without hardware, however, this is next to impossible. Given the fact that
this driver seems to be pretty much unused (it has been removed from Fedora
several versions ago and nobody complained about that), we decided to drop
this driver.
This patch moves it to staging. Some time in 2014 we will drop it completely.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Luca Risolia <luca.risolia@studio.unibo.it> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Antti Palosaari [Mon, 2 Dec 2013 16:11:21 +0000 (13:11 -0300)]
[media] m88ds3103: remove unneeded AGC from inittab
Optimal AGC is highly depended on used RF tuner and due to that
it is already included to chip configuration. However, inittab
has default AGC value, which was later replaced by one from config.
Add also comment to all chip configuration options about default
values and if those are needed to set or not.
Reported-by: David Howells <dhowells@redhat.com> Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Used synthesizer is very typical integer-N PLL, with configurable
reference frequency divider, output frequency divider and of
course N itself. Most common method to calculate values is first
select output divider, then calculate VCO frequency and finally
calculate PLL N from VCO frequency. Do it that way.
Also make some cleanups for filter logic and signal strength.
Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Antti Palosaari [Tue, 19 Nov 2013 23:32:42 +0000 (20:32 -0300)]
[media] m88ds3103: use I2C mux for tuner I2C adapter
Switch standard I2C adapter to muxed I2C adapter.
David reported that I2C adapter implementation caused deadlock.
I discussed with Jean and he suggested to implement it as a
multiplexed i2c adapter because tuner I2C bus could be seen like
own I2C segment.
Reported-by: David Howells <dhowells@redhat.com> Cc: Jean Delvare <khali@linux-fr.org> Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
On dib8000, the block error count is a monotonic 32 bits register.
With DVBv5 stats, we use a 64 bits counter, that it is reset
when a new channel is tuned.
Change the UCB counting start from 0 and to be returned with
64 bits, just like the API requests.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com> Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
Better to have Signal strength in dB.
This takes a very rough estimation for the signal strength,
that was calibrated using a Dektec DTA-2111 Gold RF generator
and a Pixelview dib8076 stick.
It estimates the signal strength using a linear equation where:
- the max is -22.5 dBm, with returns 55953
- the min is -35.0 dBm, with returns 50110
With -22dBm, the signal strengh is returned as 65535.
Unfortunately, the min strength generated with DTA-2111 is
-35dBm.
It should be noticed that approximating it by a linear equation
is not right. I should probably be splitting it into 0.5 dB
linear segments, in order to get a higher precision, just like
it is done on mb86a20s, but that would force me to add some
attenuators, in order to get dB levels below -35dBm, which is,
btw, strong enough to get signal lock.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com> Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
On ISDB-T, the valid values for interleaving are 0, 1, 2 and 4.
While the first 3 are properly reported, the last one is reported
as 3 instead. Fix it.
Tested with a Dektec DTA-2111 RF generator.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com> Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
[media] dib8000: improves the auto search mode check logic
The logic that detects if auto search mode should be used is too
complex.
Also, it doesn't cover all cases, as the dib8000_tune logic
requires either auto mode or a fully specified manual mode.
So, move it to a separate function and add some extra debug
data to help identifying when it falled back to auto mode,
because the manual settings are invalid.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com> Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
[media] dib8000: Don't let tuner hang due to a call to get_frontend()
Both dvbv5-scan and dvbv5-zap tools call FE_GET_PROPERTY inside the
loop that checks for stats. If the frontend doesn't support DVBv5, it
falls back to call the DVBv5 stats APIs(FE_READ_BER, FE_READ_SIGNAL,
FE_READ_SNR and FE_READ_UNCORRECTED_BLOCKS).
A call to FE_GET_PROPERTY makes dvb-frontend core to call get_frontend().
However, due to a race condition on dib8000 between dib8000_get_frontend
and dib8000_tune, if get_frontend occurs too early, it causes the
tune state machine to fail and not get any lock.
This patch adds a workaround code that makes get_frontend() to just
return if none of the frontends have a SYNC. This change fixed the issue
with dvbv5-scan/dvbv5-zap, but a fine-tuned logic might be needed in
the future, when we implement DVBv5 stats on this frontend.
The procedure to test the bug and the fix is the one below:
As the dvb-frontend kthread can be called anytime, it can race
with some get status ioctl. So, it seems better to avoid one to
race with the other while reading a 32 bits register.
I can't see any other reason for having a mutex there at I2C, except
to provide such kind of protection, as the I2C core already has a
mutex to protect I2C transfers.
Note: instead of this approach, it could eventually remove the dib8000
specific mutex for it, and either group the 4 ops into one xfer or
to manually control the I2C mutex. The main advantage of the current
approach is that the changes are smaller and more puntual.
Jacek Anaszewski [Wed, 18 Dec 2013 14:14:00 +0000 (11:14 -0300)]
[media] s5p-jpeg: Adjust g_volatile_ctrl callback to Exynos4x12 needs
Whereas S5PC210 device produces decoded JPEG subsampling values that
map on V4L2_JPEG_CHROMA_SUBSAMPLNG values, the Exynos4x12 device
doesn't. This patch adds helper function s5p_jpeg_to_user_subsampling,
which performs suitable translation.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Jacek Anaszewski [Thu, 21 Nov 2013 16:34:01 +0000 (13:34 -0300)]
[media] s5p-jpeg: Ensure setting correct value of the chroma subsampling control
Exynos4x12 has limitations regarding setting chroma subsampling
of an output JPEG image. It cannot be lower than the subsampling
of the raw source image. Also in case of V4L2_JPEG_CHROMA_SUBSAMPLING_GRAY
option the source image fourcc has to be V4L2_PIX_FMT_GREY.
This patch implements try_ctrl callback containing mechanism that
prevents setting invalid value of the V4L2_CID_JPEG_CHROMA_SUBSAMPLING
control.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Jacek Anaszewski [Thu, 21 Nov 2013 16:33:52 +0000 (13:33 -0300)]
[media] s5p-jpeg: Synchronize V4L2_CID_JPEG_CHROMA_SUBSAMPLING control value
When output queue fourcc is set to any flavour of YUV,
the V4L2_CID_JPEG_CHROMA_SUBSAMPLING control value as
well as its in-driver cached counterpart have to be
updated with the subsampling property of the format
so as to be able to provide correct information to the
user space and preclude setting an illegal subsampling
mode for Exynos4x12 encoder.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Jacek Anaszewski [Fri, 22 Nov 2013 09:13:34 +0000 (06:13 -0300)]
[media] s5p-jpeg: Ensure correct capture format for Exynos4x12
Adjust capture format to the Exynos4x12 device limitations,
according to the subsampling value parsed from the source
JPEG image header. If the capture format was set to YUV with
subsampling lower than the one of the source JPEG image
the decoding process would not succeed.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Jacek Anaszewski [Thu, 21 Nov 2013 16:33:09 +0000 (13:33 -0300)]
[media] s5p-jpeg: Retrieve "YCbCr subsampling" field from the jpeg header
Make s5p_jpeg_parse_hdr function capable of parsing
"YCbCr subsampling" field of a jpeg file header. Store the
parsed value in the context.
The information about source JPEG subsampling is required to
make validation of destination format possible, which must be
conducted for exynos4x12 device as the decoding process will
not succeed if the destination format is set to YUV with
subsampling lower than the one of the source JPEG image.
With this knowledge the driver can adjust the destination format
appropriately.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Laurent Pinchart [Wed, 11 Dec 2013 12:33:03 +0000 (09:33 -0300)]
[media] v4l: sh_vou: Fix warnings due to improper casts and printk formats
Use the %zu and %pad printk specifiers to print size_t and dma_addr_t
variables. This fixes warnings on platforms where dma_addr_t has a
different size than int.
Josh Wu [Tue, 10 Dec 2013 12:25:47 +0000 (09:25 -0300)]
[media] v4l: atmel-isi: Should clear bits before set the hardware register
In the ISI driver it reads the config register to get original value,
then set the correct FRATE_DIV and YCC_SWAP_MODE directly. This will
cause some bits overlap.
So we need to clear these bits first, then set correct value. This patch
fix it.
Laurent Pinchart [Sat, 23 Nov 2013 02:06:54 +0000 (23:06 -0300)]
[media] v4l: atmel-isi: Make the MCK clock optional
ISI_MCK is the sensor master clock. It should be handled by the sensor
driver directly, as the ISI has no use for that clock. Make the clock
optional here while platforms transition to the correct model.
Laurent Pinchart [Mon, 25 Nov 2013 15:21:33 +0000 (12:21 -0300)]
[media] v4l: atmel-isi: Defer clock (un)preparation to enable/disable time
The PCLK and MCK clocks are prepared and unprepared at probe and remove
time. Clock (un)preparation isn't needed before enabling/disabling the
clocks, and the enable/disable operation happen in non-atomic context.
We can thus defer (un)preparation to enable/disable time.
Josh Wu [Thu, 24 Oct 2013 07:27:11 +0000 (04:27 -0300)]
[media] v4l: atmel-isi: remove SOF wait in start_streaming()
when a userspace applications calls the VIDIOC_STREAMON ioctl. The
V4L2 core calls the soc_camera_streamon function, which is responsible
for starting the video stream. It does so by first starting the atmel-isi
host by a call to the vb2_streamon function, and then starting the sensor
by a call to the video.s_stream sensor subdev operation.
That means we wait for a SOF in start_streaming() before call sensor's
s_stream(). It is possible no VSYNC interrupt arrive as the sensor
hasn't been started yet.
To avoid such case, this patch remove the code to wait for the VSYNC
interrupt. And such code is not necessary.
si4713_set_rds_radio_text will overwrite the terminating zero at the
end of the rds radio text string in order to send out a carriage return
as per the RDS spec.
Use a separate char buffer for the CR instead of corrupting the control
string.
Dinesh Ram [Tue, 15 Oct 2013 15:24:44 +0000 (12:24 -0300)]
[media] si4713: move supply list to si4713_platform_data
The supply list is needed by the platform driver, but not by the usb driver.
So this information belongs to the platform data and should not be hardcoded
in the subdevice driver.
Dinesh Ram [Tue, 15 Oct 2013 15:24:41 +0000 (12:24 -0300)]
[media] si4713: HID blacklist Si4713 USB development board
The Si4713 development board contains a Si4713 FM transmitter chip
and is handled by the radio-usb-si4713 driver.
The board reports itself as (10c4:8244) Cygnal Integrated Products, Inc.
and misidentifies itself as a HID device in its USB interface descriptor.
This patch ignores this device as an HID device and hence loads the custom driver.
Dinesh Ram [Tue, 15 Oct 2013 15:24:40 +0000 (12:24 -0300)]
[media] si4713: Bug fix for si4713_tx_tune_power() method in the i2c driver
In the si4713_tx_tune_power() method, the args array element 'power'
can take values between SI4713_MIN_POWER and SI4713_MAX_POWER. power = 0
is also valid. All the values (0 > power < SI4713_MIN_POWER) are illegal
and hence are all mapped to SI4713_MIN_POWER.
Dinesh Ram [Tue, 15 Oct 2013 15:24:38 +0000 (12:24 -0300)]
[media] si4713: Modified i2c driver to handle cases where interrupts are not used
Checks have been introduced at several places in the code to test if an
interrupt is set or not. For devices which do not use the interrupt, to
get a valid response, within a specified timeout, the device is polled
instead.
Lisa Nguyen [Wed, 11 Dec 2013 06:09:22 +0000 (03:09 -0300)]
[media] staging: media: davinci_vpfe: Rewrite return statement in vpfe_video.c
Rewrite the return statement in vpfe_video.c. This will prevent
the checkpatch.pl script from generating a warning saying
to remove () from this particular return statement.
Laurent Pinchart [Fri, 17 May 2013 10:31:04 +0000 (07:31 -0300)]
[media] v4l: of: Drop endpoint node reference in v4l2_of_get_remote_port()
The v4l2_of_get_remote_port() function acquires a reference to an
endpoint node through a phandle and then returns the node's parent,
without dropping the reference to the endpoint node. Fix it.
Laurent Pinchart [Fri, 17 May 2013 10:31:04 +0000 (07:31 -0300)]
[media] v4l: of: Return an int in v4l2_of_parse_endpoint()
When CONFIG_OF is not defined the v4l2_of_parse_endpoint() function is
defined as a stub that returns -ENOSYS. Make the real function return an
integer as well to be able to differentiate between the two cases.
[media] omap3isp: Modify clocks registration to avoid circular references
The clock core code is going to be modified so clk_get() takes
reference on the clock provider module. Until the potential circular
reference issue is properly addressed, we pass NULL as the first
argument to clk_register(), in order to disallow sub-devices taking
a reference on the ISP module back trough clk_get(). This should
prevent locking the modules in memory.
Jacek Anaszewski [Mon, 25 Nov 2013 09:58:13 +0000 (06:58 -0300)]
[media] s5p-jpeg: Fix clock resource management
Standard suspend/resume path is called after runtime resume
of the given device, so suspend/resume callbacks must do all
clock management done also by runtime pm to allow for proper
power domain shutdown. Moreover, JPEG clock is enabled from
probe function but is is not necessary. This patch also moves
control of jpeg clock to runtime_pm callbacks.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com> Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Jacek Anaszewski [Mon, 25 Nov 2013 09:58:11 +0000 (06:58 -0300)]
[media] s5p-jpeg: Remove superfluous call to the jpeg_bound_align_image function
Aligning capture queue image dimensions while enqueuing output
queue doesn't make a sense as the S_FMT ioctl might have not
been called for the capture queue until that moment, whereas
it is required to know capture format as the type of alignment
heavily depends on it.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Jacek Anaszewski [Mon, 25 Nov 2013 09:58:10 +0000 (06:58 -0300)]
[media] s5p-jpeg: Fix erroneous condition while validating bytesperline value
The aim of the condition is ensuring that the bytesperline
value set by the user space application is proper for the
given format and adjusting it if isn't. As the depth value
of the format description entry is expressed in bits then
the bytesperline value needs to be divided, not multiplied,
by that value to get the number of bytes required to store
single line of image samples.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Jacek Anaszewski [Mon, 25 Nov 2013 09:58:08 +0000 (06:58 -0300)]
[media] s5p-jpeg: Reorder quantization tables
Reorder quantization tables so that their elements
are arranged in the manner reflecting compression
quality level that is in accordance with V4L2 documentation,
i.e. the larger value of the V4L2_CID_JPEG_COMPRESSION_QUALITY
control the better image quality, and thus lower compression
quality. The modification allows also to get rid of
reverse logic in the s_ctrl callback while assigning
user space value to the ctx->compr_quality variable.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
[media] s5p-jpeg: Add initial device tree support for S5PV210/Exynos4210 SoCs
This patch enables the JPEG codec on S5PV210 and Exynos4210 SoCs. There are
some differences in newer versions of the JPEG codec IP on SoCs like Exynos4x12
and Exynos5 series and support for them will be added in subsequent patches.
Merge the media fixes merged upstream for v3.13-rc4
* upstream-fixes: (30 commits)
[media] videobuf2-dma-sg: fix possible memory leak
[media] vb2: regression fix: always set length field.
[media] mt9p031: Include linux/of.h header
[media] rtl2830: add parent for I2C adapter
[media] media: marvell-ccic: use devm to release clk
[media] ths7303: Declare as static a private function
[media] em28xx-video: Swap release order to avoid lock nesting
[media] usbtv: Add support for PAL video source
[media] media_tree: Fix spelling errors
[media] videobuf2: Add support for file access mode flags for DMABUF exporting
[media] radio-shark2: Mark shark_resume_leds() inline to kill compiler warning
[media] radio-shark: Mark shark_resume_leds() inline to kill compiler warning
[media] af9035: unlock on error in af9035_i2c_master_xfer()
[media] af9033: fix broken I2C
[media] v4l: omap3isp: Don't check for missing get_fmt op on remote subdev
[media] af9035: fix broken I2C and USB I/O
[media] wm8775: fix broken audio routing
[media] marvell-ccic: drop resource free in driver remove
[media] tef6862/radio-tea5764: actually assign clamp result
[media] cx231xx: use after free on error path in probe
...
Laurent Pinchart [Tue, 15 Oct 2013 21:58:43 +0000 (18:58 -0300)]
[media] v4l: vsp1: Supply frames to the DU continuously
When operating in DU output mode (deep pipeline to the DU through the
LIF), the VSP1 needs to constantly supply frames to the display. To
ensure reuse the last queued buffer instead of returning it to the user.
The sensor can scale the image down using binning by 1, 2 or 4 in both
directions. Update size enumeration and ratio and binning factor
computation accordingly.
projects / ~andy / linux / log