Magnus Damm [Thu, 6 Aug 2009 14:28:12 +0000 (14:28 +0000)]
sh: LCDC SYS bus access wait fix
Update the SuperH Mobile LCDC driver to wait for SYS bus to
become idle after reading or writing. This is needed by the
kfr2r09 board, but also fixes potential problems on other
boards making use of the LCDC in a SYS configuration.
Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Wed, 29 Jul 2009 15:06:15 +0000 (15:06 +0000)]
sh: kfr2r09 romImage support V2
This patch is romImage support for the kfr2r09 board V2.
The partner-jet-setup.txt file is converted into assembly code
which becomes the first code to execute from the reset vector.
The file partner-jet-setup.txt can also be used to setup
the hardware using a JTAG debugger so booting from RAM can
be done without burning the code to flash.
Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Stuart Menefy [Wed, 29 Jul 2009 14:01:24 +0000 (23:01 +0900)]
sh: Rework irqflags tracing to fix up CONFIG_PROVE_LOCKING.
This cleans up the irqflags tracing code quite a bit and ties it
in to various missing callsites that caused an imbalance when
CONFIG_PROVE_LOCKING was enabled.
Magnus Damm [Thu, 23 Jul 2009 08:59:48 +0000 (08:59 +0000)]
sh: kfr2r09 board support - mach-type and defconfig
This patch adds a defconfig and a mach-types entry for
the kfr2r09 board.
At this point only a few devices like SCIF, KEYSC and
NOR Flash are supported together with sh7724 devices
such as IIC0, IIC1 and the multimedia blocks exported
via UIO.
Kexec is supported, but booting from flash is not (yet).
Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Wed, 22 Jul 2009 16:20:54 +0000 (16:20 +0000)]
sh: kfr2r09 board support - SCIF console
This patch adds basic kfr2r09 board support. Only
the SCIF1 console is supported with this patch, but
this patch and a proper sh7724 configuration is all
that is needed. Combine with an initramfs to have a
small RAM based kernel and distribution booted as
zImage from RAM via JTAG.
Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Wed, 22 Jul 2009 15:14:29 +0000 (15:14 +0000)]
sh: convert processor device setup functions to arch_initcall()
Convert the processor platform device setup
functions from __initcall() and sometimes
device_initcall() to arch_initcall().
This makes sure that the platform devices are
registered a bit earlier so the devices are
available when drivers register using initcall
levels earlier than device_initcall().
A good example is platform devices needed by
i2c-sh_mobile.c which registers a bit earlier
using subsys_initcall().
Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Wed, 22 Jul 2009 14:58:39 +0000 (14:58 +0000)]
i2c: change i2c-sh_mobile.c module_init() to subsys_initcall()
Convert the i2c-sh_mobile i2c bus driver to use
subsys_initcall() instead of module_init().
This change makes the driver register a bit earlier which
together with earlier platform data moves the time for probe().
The earlier probe() makes it possible to use i2c_get_adapter()
and i2c_transfer() from device_initcall().
The same strategy is used by other i2c bus drivers such as
i2c-pxa.c and i2c-s3c2410.c.
Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Wed, 22 Jul 2009 14:41:35 +0000 (14:41 +0000)]
usb: m66592-udc platform data on_chip support
Convert the m66592-udc driver to use the on_chip flag
from platform data to enable on chip behaviour instead
of relying on CONFIG_SUPERH_BUILT_IN_M66592 ugliness.
This makes the code cleaner and also allows us to support
both external and internal m66592 with the same kernel.
It also makes the Kconfig part more future proof since
we with this patch can add support for new processors
with on-chip m66592 without modifying the Kconfig.
The patch adds a m66592 header file for platform data
and ties in platform data to the existing m66592 devices.
Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Merge branch 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
genirq: Fix UP compile failure caused by irq_thread_check_affinity
Merge branch 'lockdep-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/peterz/linux-2.6-lockdep
* 'lockdep-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/peterz/linux-2.6-lockdep:
lockdep: Fix lockdep annotation for pipe_double_lock()
Bruno Premont [Wed, 22 Jul 2009 20:22:32 +0000 (22:22 +0200)]
genirq: Fix UP compile failure caused by irq_thread_check_affinity
Since genirq: Delegate irq affinity setting to the irq thread
(591d2fb02ea80472d846c0b8507007806bdd69cc) compilation with
CONFIG_SMP=n fails with following error:
/usr/src/linux-2.6/kernel/irq/manage.c:
In function 'irq_thread_check_affinity':
/usr/src/linux-2.6/kernel/irq/manage.c:475:
error: 'struct irq_desc' has no member named 'affinity'
make[4]: *** [kernel/irq/manage.o] Error 1
That commit adds a new function irq_thread_check_affinity() which
uses struct irq_desc.affinity which is only available for CONFIG_SMP=y.
Move that function under #ifdef CONFIG_SMP.
[ tglx@brownpaperbag: compile and boot tested on UP and SMP ]
Signed-off-by: Bruno Premont <bonbons@linux-vserver.org>
LKML-Reference: <20090722222232.2eb3e1c4@neptune.home> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Peter Zijlstra [Tue, 21 Jul 2009 08:09:23 +0000 (10:09 +0200)]
lockdep: Fix lockdep annotation for pipe_double_lock()
The presumed use of the pipe_double_lock() routine is to lock 2 locks in
a deadlock free way by ordering the locks by their address. However it
fails to keep the specified lock classes in order and explicitly
annotates a deadlock.
Rectify this.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Acked-by: Miklos Szeredi <mszeredi@suse.cz>
LKML-Reference: <1248163763.15751.11098.camel@twins>
Merge branch 'perf-counters-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/peterz/linux-2.6-perf
* 'perf-counters-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/peterz/linux-2.6-perf: (31 commits)
perf_counter tools: Give perf top inherit option
perf_counter tools: Fix vmlinux symbol generation breakage
perf_counter: Detect debugfs location
perf_counter: Add tracepoint support to perf list, perf stat
perf symbol: C++ demangling
perf: avoid structure size confusion by using a fixed size
perf_counter: Fix throttle/unthrottle event logging
perf_counter: Improve perf stat and perf record option parsing
perf_counter: PERF_SAMPLE_ID and inherited counters
perf_counter: Plug more stack leaks
perf: Fix stack data leak
perf_counter: Remove unused variables
perf_counter: Make call graph option consistent
perf_counter: Add perf record option to log addresses
perf_counter: Log vfork as a fork event
perf_counter: Synthesize VDSO mmap event
perf_counter: Make sure we dont leak kernel memory to userspace
perf_counter tools: Fix index boundary check
perf_counter: Fix the tracepoint channel to perfcounters
perf_counter, x86: Extend perf_counter Pentium M support
...
Merge branch 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: fix nr_uninterruptible accounting of frozen tasks really
sched: fix load average accounting vs. cpu hotplug
sched: Account for vruntime wrapping
Merge branch 'tj-block-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/misc
* 'tj-block-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/misc:
virtio_blk: mark virtio_blk with __refdata to kill spurious section mismatch
block: sysfs fix mismatched queue_var_{store,show} in 64bit kernel
ataflop: adjust NULL test
block: fix failfast merge testing in elv_rq_merge_ok()
z2ram: Small cleanup for z2ram.c
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (37 commits)
sky2: Avoid races in sky2_down
drivers/net/mlx4: Adjust constant
drivers/net: Move a dereference below a NULL test
drivers/net: Move a dereference below a NULL test
connector: maintainer/mail update.
USB host CDC Phonet network interface driver
macsonic, jazzsonic: fix oops on module unload
macsonic: move probe function to .devinit.text
can: switch carrier on if device was stopped while in bus-off state
can: restart device even if dev_alloc_skb() fails
can: sja1000: remove duplicated includes
New device ID for sc92031 [1088:2031]
3c589_cs: re-initialize the multicast in the tc589_reset
Fix error return for setsockopt(SO_TIMESTAMPING)
netxen: fix thermal check and shutdown
netxen: fix deadlock on dev close
netxen: fix context deletion sequence
net: Micrel KS8851 SPI network driver
tcp: Use correct peer adr when copying MD5 keys
tcp: Fix MD5 signature checking on IPv4 mapped sockets
...
Merge branch 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
NFSv4: Fix a problem whereby a buggy server can oops the kernel
NFSv4: Fix an NFSv4 mount regression
NFSv4: Fix an Oops in nfs4_free_lock_state
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: ctxfi: Swapped SURROUND-SIDE channels on emu20k2
ALSA: ca0106 - Fix the max capture buffer size
ALSA: hda - Fix pin-setup for Sony VAIO with STAC9872 codecs
ALSA: hda - Add quirk for Gateway T6834c laptop
ALSA: OSS sequencer should be initialized after snd_seq_system_client_init
ALSA: sound/isa: convert nested spin_lock_irqsave to spin_lock
ALSA: hda_codec: Check for invalid zero connections
Arjan van de Ven [Tue, 21 Jul 2009 07:55:05 +0000 (00:55 -0700)]
perf: fix stack data leak
the "reserved" field was not initialized to zero, resulting in 4 bytes
of stack data leaking to userspace....
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Galbraith [Mon, 20 Jul 2009 12:01:38 +0000 (14:01 +0200)]
perf_counter tools: Fix vmlinux symbol generation breakage
vmlinux meets the criteria for symbol adjustment, which breaks vmlinux generated symbols.
Fix this by exempting vmlinux. This is a bit fragile in that someone could change the
kernel dso's name, but currently that name is also hardwired.
Signed-off-by: Mike Galbraith <efault@gmx.de> Cc: Ingo Molnar <mingo@elte.hu> Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1248091298.18702.18.camel@marge.simson.net>
Jason Baron [Tue, 21 Jul 2009 18:16:29 +0000 (14:16 -0400)]
perf_counter: Detect debugfs location
If "/sys/kernel/debug" is not a debugfs mount point, search for the debugfs
filesystem in /proc/mounts, but also allows the user to specify
'--debugfs-dir=blah' or set the environment variable: 'PERF_DEBUGFS_DIR'
Signed-off-by: Jason Baron <jbaron@redhat.com>
[ also made it probe "/debug" by default ] Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <20090721181629.GA3094@redhat.com>
Jason Baron [Tue, 21 Jul 2009 16:20:22 +0000 (12:20 -0400)]
perf_counter: Add tracepoint support to perf list, perf stat
Add support to 'perf list' and 'perf stat' for kernel tracepoints. The
implementation creates a 'for_each_subsystem' and 'for_each_event' for
easy iteration over the tracepoints.
Arjan van de Ven [Tue, 21 Jul 2009 05:54:26 +0000 (22:54 -0700)]
perf: avoid structure size confusion by using a fixed size
for some reason, this structure gets compiled as 36 bytes in some files
(the ones that alloacte it) but 40 bytes in others (the ones that use it).
The cause is an off_t type that gets a different size in different
compilation units for some yet-to-be-explained reason.
But the effect is disasterous; the size/offset members of the struct
are at different offsets, and result in mostly complete garbage.
The parser in perf is so robust that this all gets hidden, and after
skipping an certain amount of samples, it recovers.... so this bug
is not normally noticed.
.... except when you want every sample to be exact.
Fix this by just using an explicitly sized type.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <4A655917.9080504@linux.intel.com>
Peter Zijlstra [Tue, 21 Jul 2009 11:19:40 +0000 (13:19 +0200)]
perf_counter: PERF_SAMPLE_ID and inherited counters
Anton noted that for inherited counters the counter-id as provided by
PERF_SAMPLE_ID isn't mappable to the id found through PERF_RECORD_ID
because each inherited counter gets its own id.
His suggestion was to always return the parent counter id, since that
is the primary counter id as exposed. However, these inherited
counters have a unique identifier so that events like
PERF_EVENT_PERIOD and PERF_EVENT_THROTTLE can be specific about which
counter gets modified, which is important when trying to normalize the
sample streams.
This patch removes PERF_EVENT_PERIOD in favour of PERF_SAMPLE_PERIOD,
which is more useful anyway, since changing periods became a lot more
common than initially thought -- rendering PERF_EVENT_PERIOD the less
useful solution (also, PERF_SAMPLE_PERIOD reports the more accurate
value, since it reports the value used to trigger the overflow,
whereas PERF_EVENT_PERIOD simply reports the requested period changed,
which might only take effect on the next cycle).
This still leaves us PERF_EVENT_THROTTLE to consider, but since that
_should_ be a rare occurrence, and linking it to a primary id is the
most useful bit to diagnose the problem, we introduce a
PERF_SAMPLE_STREAM_ID, for those few cases where the full
reconstruction is important.
[Does change the ABI a little, but I see no other way out]
Suggested-by: Anton Blanchard <anton@samba.org> Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1248095846.15751.8781.camel@twins>
There's some odd bug in gcc-4.2 where it miscompiles a simple loop whent
he loop counter is of type 'unsigned char' and it should count to 128.
The compiler will incorrectly decide that a trivial loop like this:
unsigned char i, ...
for (i = 0; i < 128; i++) {
..
is endless, and will compile it to a single instruction that just
branches to itself.
This was triggered by the addition of '-fno-strict-overflow', and we
could play games with compiler versions and go back to '-fwrapv'
instead, but the trivial way to avoid it is to just make the loop
induction variable be an 'int' instead.
Thanks to Krzysztof Oledzki for reporting and testing and to Troy Moure
for digging through assembler differences and finding it.
Reported-and-tested-by: Krzysztof Oledzki <olel@ans.pl> Found-by: Troy Moure <twmoure@szypr.net> Gcc-bug-acked-by: Ian Lance Taylor <iant@google.com> Cc: stable@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Peter Zijlstra [Wed, 22 Jul 2009 12:18:35 +0000 (14:18 +0200)]
softirq: introduce tasklet_hrtimer infrastructure
commit ca109491f (hrtimer: removing all ur callback modes) moved all
hrtimer callbacks into hard interrupt context when high resolution
timers are active. That breaks code which relied on the assumption
that the callback happens in softirq context.
Provide a generic infrastructure which combines tasklets and hrtimers
together to provide an in-softirq hrtimer experience.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: torvalds@linux-foundation.org Cc: kaber@trash.net Cc: David Miller <davem@davemloft.net>
LKML-Reference: <1248265724.27058.1366.camel@twins> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Mike McCormack [Wed, 22 Jul 2009 03:57:56 +0000 (20:57 -0700)]
sky2: Avoid races in sky2_down
Reset rx chain before trying to drain it.
Shut interrupts off last, incase there's something to report.
Signed-off-by: Mike McCormack <mikem@ring3k.org> Acked-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Maxime Bizon [Thu, 16 Jul 2009 06:32:52 +0000 (06:32 +0000)]
ide: fix memory leak when flush command is issued
I'm using ide on 2.6.30.1 with xfs filesystem. I noticed a kernel memory
leak after writing lots of data, the kmalloc-96 slab cache keeps
growing. It seems the struct ide_cmd kmalloced by idedisk_prepare_flush
is never kfreed.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr> Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
NFSv4: Fix a problem whereby a buggy server can oops the kernel
We just had a case in which a buggy server occasionally returns the wrong
attributes during an OPEN call. While the client does catch this sort of
condition in nfs4_open_done(), and causes the nfs4_atomic_open() to return
-EISDIR, the logic in nfs_atomic_lookup() is broken, since it causes a
fallback to an ordinary lookup instead of just returning the error.
When the buggy server then returns a regular file for the fallback lookup,
the VFS allows the open, and bad things start to happen, since the open
file doesn't have any associated NFSv4 state.
The fix is firstly to return the EISDIR/ENOTDIR errors immediately, and
secondly to ensure that we are always careful when dereferencing the
nfs_open_context state pointer.
Commit 008f55d0e019943323c20a03493a2ba5672a4cc8 (nfs41: recover lease in
_nfs4_lookup_root) forces the state manager to always run on mount. This is
a bug in the case of NFSv4.0, which doesn't require us to send a
setclientid until we want to grab file state.
In any case, this is completely the wrong place to be doing state
management. Moving that code into nfs4_init_session...
The oops http://www.kerneloops.org/raw.php?rawid=537858&msgid= appears to
be due to the nfs4_lock_state->ls_state field being uninitialised. This
happens if the call to nfs4_free_lock_state() is triggered at the end of
nfs4_get_lock_state().
The fix is to move the initialisation of ls_state into the allocator.
Julia Lawall [Sun, 19 Jul 2009 06:09:25 +0000 (06:09 +0000)]
drivers/net/mlx4: Adjust constant
The values in the advertising field are typically ADVERTISED_xxx, not
SUPPORTED_xxx. Both SUPPORTED_10000baseT_Full and
ADVERTISED_1000baseT_Full have the same value.
The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
Many Nokia handsets support a Phonet interface to the cellular modem
via a vendor-specific USB interface. CDC Phonet follows the
Communications Device Class model, with one control interface, and
and a pair of inactive and active data alternative interface. The later
has two bulk endpoint, one per direction.
This was tested against Nokia E61, Nokia N95, and the existing Phonet
gadget function for the Linux composite USB gadget framework.
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
A pointer to mac_sonic_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
Various other functions that are called by mac_sonic_probe need to move
to .devinit.text, too.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Tested-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
* fix/misc:
ALSA: ca0106 - Fix the max capture buffer size
ALSA: OSS sequencer should be initialized after snd_seq_system_client_init
ALSA: sound/isa: convert nested spin_lock_irqsave to spin_lock
* fix/hda:
ALSA: hda - Fix pin-setup for Sony VAIO with STAC9872 codecs
ALSA: hda - Add quirk for Gateway T6834c laptop
ALSA: hda_codec: Check for invalid zero connections
Thomas Gleixner [Tue, 21 Jul 2009 09:09:39 +0000 (11:09 +0200)]
genirq: Delegate irq affinity setting to the irq thread
irq_set_thread_affinity() calls set_cpus_allowed_ptr() which might
sleep, but irq_set_thread_affinity() is called with desc->lock held
and can be called from hard interrupt context as well. The code has
another bug as it does not hold a ref on the task struct as required
by set_cpus_allowed_ptr().
Just set the IRQTF_AFFINITY bit in action->thread_flags. The next time
the thread runs it migrates itself. Solves all of the above problems
nicely.
Add kerneldoc to irq_set_thread_affinity() while at it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <new-submission>
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
9p: Fix incorrect parameters to v9fs_file_readn.
9p: Possible regression in p9_client_stat
9p: default 9p transport module fix
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
cifs: free nativeFileSystem field before allocating a new one
[CIFS] Distinguish posix opens and mkdirs from legacy mkdirs in stats
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin: (21 commits)
Blackfin: define HARDIRQ_BITS again for now
arch/blackfin: Add kmalloc NULL tests
Blackfin: add CPLB entries for Core B on-chip L1 SRAM regions
Blackfin: work around anomaly 05000189
Blackfin: drop per-cpu loops_per_jiffy tracking
Blackfin: fix bugs in GPIO resume code
Blackfin: bf537-stamp: fix irq decl for AD7142
Blackfin: fix handling of IPEND in interrupt context save
Blackfin: drop duplicate runtime checking of anomaly 05000448
Blackfin: fix incomplete renaming of the bfin-twi-lcd driver
Blackfin: fix wrong CTS inversion
Blackfin: update handling of anomaly 364 (wrong rev id in BF527-0.1)
Blackfin: fix early_dma_memcpy() handling of busy channels
Blackfin: handle BF561 Core B memory regions better when SMP=n
Blackfin: fix miscompilation in lshrdi3
Blackfin: fix silent crash when no uClinux MTD filesystem exists
Blackfin: restore exception banner when dumping crash info
Blackfin: work around anomaly 05000281
Blackfin: update anomaly lists to match latest sheets/usage
Blackfin: drop dead flash_probe call
...
Nicolas Pitre [Sun, 19 Jul 2009 00:34:37 +0000 (20:34 -0400)]
mvsdio: fix handling of partial word at the end of PIO transfer
Standard data flow for MMC/SD/SDIO cards requires that the mvsdio
controller be set for big endian operation. This is causing problems
with buffers which length is not a multiple of 4 bytes as the last
partial word doesn't get shifted all the way and stored properly in
memory. Let's compensate for this.
Signed-off-by: Nicolas Pitre <nico@marvell.com> CC: stable@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Julia Lawall [Mon, 20 Jul 2009 15:05:07 +0000 (16:05 +0100)]
specialix.c: convert nested spin_lock_irqsave to spin_lock
If spin_lock_irqsave is called twice in a row with the same second
argument, the interrupt state at the point of the second call overwrites
the value saved by the first call. Indeed, the second call does not
need to save the interrupt state, so it is changed to a simple
spin_lock.
The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
Kay Sievers [Mon, 20 Jul 2009 15:04:55 +0000 (16:04 +0100)]
vc: create vcs(a) devices for consoles
The buffer for the consoles are unconditionally allocated at con_init()
time, which miss the creation of the vcs(a) devices.
Since 2.6.30 (commit 4995f8ef9d3aac72745e12419d7fbaa8d01b1d81, 'vcs:
hook sysfs devices into object lifetime instead of "binding"' to be
exact) these devices are no longer created at open() and removed on
close(), but controlled by the lifetime of the buffers.
can: switch carrier on if device was stopped while in bus-off state
This patch fixes a problem when a device is stopped while in the
bus-off state. Then the carrier remains off forever.
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@skynet.be> Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
If dev_alloc_skb() failed in can_restart(), the device was left behind
in the bus-off state. This patch restarts the device nevertheless.
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be> Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Remove duplicated #include('s) in
drivers/net/can/sja1000/sja1000.c
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com> Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
rain_maker@root-forum.org wrote:
> Hello cesar,
>
> In a recent thread in a german linux forum, a user reported his PIC
> NIC not being recognized by the kernel.
>
> Fortunately he provided enough information and I was able to help him
> and get the device working with the sc92031 driver.
>
> The device ID is [1088:2031] (Vendor is called "Microcomputer Systems
> (M) Son"), here is the respective thread in "ubuntuusers.de"
>
> http://forum.ubuntuusers.de/topic/lankarte-unter-xubuntu-wird-nicht-erkannt/
>
> (Although you might not speak german, the code provided will show
> you, that the device is actually working with your driver).
>
> It would be nice, if you include this new device ID to the
> sc92031-driver.
>
> Regards,
>
> Axel Köllhofer (aka Rain_Maker)
Cc: rain_maker@root-forum.org Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net> Signed-off-by: David S. Miller <davem@davemloft.net>
The tx ring accounting fix in commit cb2107be43d2fc5eadec58b92b
("netxen: fix tx ring accounting") introduced intermittent
deadlock when inteface is going down.
This was possibly combined effect of speculative tx pause,
calling netif_tx_lock instead of queue lock and unclean
synchronization with napi which could end up unmasking
interrupt.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
o Use D3 reset context deletion for NX2031, it cleans up
more resources in the firmware.
o Release rx buffers after hardware context has been reset.
o Delete tx context after rx context, some firmware control
commands are sent on tx context, so it should be the last
to go.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Frank Roth [Mon, 20 Jul 2009 15:00:14 +0000 (17:00 +0200)]
ALSA: ctxfi: Swapped SURROUND-SIDE channels on emu20k2
On Soundblaster X-FI Titanium with emu20k2 the SIDE and SURROUND
channels were swapped and wrong.
I double checked it with connector colors and creative soundblaster
windows drivers.
So I swapped them to the true order.
Now "speaker-test -c6" and "speaker-test -c8" are working fine.
Signed-off-by: Frank Roth <frashman@freenet.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
projects / ~andy / linux / log