Olof Johansson [Sun, 22 Dec 2013 19:42:50 +0000 (11:42 -0800)]
Merge tag 'at91-drivers' of git://github.com/at91linux/linux-at91 into next/drivers
From Nicolas Ferre:
AT91 crypto drivers DT support:
- add DT to sha/des/aes existing drivers
- add DMA DT
- all documentation added to crypto/atmel-crypto.txt file
* tag 'at91-drivers' of git://github.com/at91linux/linux-at91:
crypto: atmel-sha - add sha information to the log
crypto: atmel-sha - add support for Device Tree
crypto: atmel-tdes - add support for Device Tree
crypto: atmel-aes - add support for Device Tree
Kevin Hilman [Fri, 20 Dec 2013 19:23:08 +0000 (11:23 -0800)]
Merge tag 'renesas-usb-r8a66597-hcd-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/drivers
From Simon Horman:
Renesas USB r8a66597 HCD update for v3.14
Convert to clk_prepare/unprepare
* tag 'renesas-usb-r8a66597-hcd-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
usb: r8a66597-hcd: Convert to clk_prepare/unprepare
ARM: at91: dt: at91rm9200ek: add emac and nor flash support
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
[nicolas.ferre@atmel.com: remove one macb node too many] Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Nicolas Ferre [Fri, 15 Nov 2013 09:58:40 +0000 (10:58 +0100)]
ARM: at91/dt: binding: add precision to AIC documentation
In response to the "undocumented compatible strings" message, here is a
patch which is adding the precision of two "chips" that should be used for
the "atmel,<chip>-aic" compatibility string.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Boris BREZILLON [Wed, 28 Aug 2013 11:03:39 +0000 (13:03 +0200)]
ARM: at91/dt: add ethernet phy to at91rm9200ek board
Add ethernet phy node in at91rm9200ek.dts.
The reg register is not specified, as it may differ depending on the init
process of the board:
ADDR0/1 phy pins are connected to PA13/14 rm9200 pins. Which means the phy
will take its address from these pins during the reset process.
The macb driver will launch a full scan on the mdio bus to discover the phy
address.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
[nicolas.ferre@atmel.com: changed to IRQ_TYPE_EDGE_BOTH as asked by Boris] Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Olof Johansson [Wed, 4 Dec 2013 21:38:20 +0000 (13:38 -0800)]
Merge tag 's3c64xx-dmaengine' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc into next/drivers
From Tomasz Figa via Mark Brown:
ARM: s3c64xx: Convert to dmaengine
This series of commits from Tomasz converting s3c64xx to use dmaengine
rather than the old s3c-dma API missed the v3.13 merge window - Kukjin
said that he'd applied it (which should mean it's OK from a review point
of view) but it didn't make it into -next or a pull request.
Since a s3c64xx based system is one of my primary development platforms
it'd be really helpful if I could merge this into both ASoC and SPI,
I've got some patches for ASoC ready to go converting to use dmaengine
directly which help with multiplatform and there's some other dmaengine
work for SPI in progress too. I've therefore made this signed tag, it'd
be great if it could be merged into both arm-soc and those two trees.
* tag 's3c64xx-dmaengine' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc:
spi: s3c64xx: Always select S3C64XX_PL080 when ARCH_S3C64XX is enabled
clk: samsung: s3c64xx: Remove clock aliases of old DMA driver
ARM: s3c64xx: Remove legacy DMA driver
clk: samsung: s3c64xx: Add aliases for DMA clocks
ARM: s3c64xx: Add support for DMA using generic amba-pl08x driver
spi: s3c64xx: Do not require legacy DMA API in case of S3C64XX
Boris BREZILLON [Mon, 2 Dec 2013 14:12:14 +0000 (15:12 +0100)]
ARM: at91/dt: remove old clk material
This patch removes the old main clk node which is now useless as sama5d3
SoCs and boards are no longer compatible with the old at91 clk
implementations.
It also remove old clock definitions (clock definitions using at91 old clk
framework).
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Boris BREZILLON [Fri, 11 Oct 2013 12:43:35 +0000 (14:43 +0200)]
ARM: at91: move sama5d3 SoC to common clk
This patch removes the selection of AT91_USE_OLD_CLK when selecting sama5d3
SoC support. This will enable automatically enable COMMON_CLK_AT91 option
and add support for at91 common clk implementation.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Boris BREZILLON [Fri, 11 Oct 2013 12:43:31 +0000 (14:43 +0200)]
ARM: at91: prepare sama5 dt boards transition to common clk
This patch prepare the transition to common clk for sama5 dt boards by
replacing the timer init callback.
Clocks registration cannot be done in early init callback (as formerly done
by the old clk implementation) because it requires dynamic allocation
which is not ready yet during early init.
In the other hand, at91 clocks must be registered before
at91sam926x_pit_init is called because PIT (Periodic Interval Timer) driver
request the master clk (mck).
A new function (at91sama5_dt_timer_init) is created to fullfil these needs.
This function registers all at91 clks using the dt definition before
calling the PIT init function.
The device tree clock registration is enabled only if common clk is
selected. Else the old clk registration is been done during
at91_dt_initialize call.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Boris BREZILLON [Fri, 11 Oct 2013 11:49:10 +0000 (13:49 +0200)]
ARM: at91: add new compatible strings for pmc driver
This patch adds new compatible string for PMC node to prepare the
transition to common clk.
These compatible string come from pmc driver in clk subsystem and are
needed to provide new device tree compatibility with old at91 clks
(device tree using common clks will use the new compatible strings).
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com> Acked-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Boris BREZILLON [Fri, 11 Oct 2013 11:46:28 +0000 (13:46 +0200)]
ARM: at91: move pit timer to common clk framework
Use device tree to get the source clock of the PIT (Periodic Interval Timer).
If the clock is not found in device tree (or dt is not enabled) we'll try to
get it using clk_lookup definitions.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com> Acked-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch adds new at91 clks dt bindings documentation.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com> Acked-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Boris BREZILLON [Fri, 11 Oct 2013 11:27:06 +0000 (13:27 +0200)]
clk: at91: add PMC smd clock
This patch adds at91 smd (Soft Modem) clock implementation using common clk
framework.
Not used by any driver right now.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com> Acked-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Boris BREZILLON [Thu, 17 Oct 2013 16:55:41 +0000 (18:55 +0200)]
clk: at91: add PMC usb clock
This patch adds new at91 usb clock implementation using common clk framework.
This clock is used to clock usb ports (ohci, ehci and udc).
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com> Acked-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Boris BREZILLON [Fri, 11 Oct 2013 10:22:06 +0000 (12:22 +0200)]
clk: at91: add PMC utmi clock
This adds new at91 utmi clock implementation using common clk framework.
This clock is a pll with a fixed factor (x40).
It is used as a source for usb clock.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com> Acked-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Boris BREZILLON [Fri, 11 Oct 2013 09:57:04 +0000 (11:57 +0200)]
clk: at91: add PMC programmable clocks
This patch adds new at91 programmable clocks implementation using common clk
framework.
A programmable clock is a clock which can be exported on a given pin to clock
external devices.
Each programmable clock is given an id (from 0 to 8).
The number of available programmable clocks depends on the SoC you're using.
Programmable clock driver only implements the clock setting (clock rate and
parent setting). It must be chained to a system clock in order to
enable/disable the generated clock.
The PCKX pins used to output the clock signals must be assigned to the
appropriate peripheral (see atmel's datasheets).
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com> Acked-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Boris BREZILLON [Fri, 11 Oct 2013 09:44:36 +0000 (11:44 +0200)]
clk: at91: add PMC peripheral clocks
This patch adds new at91 peripheral clock implementation using common clk
framework.
Almost all peripherals provided by at91 SoCs need a clock to work properly.
This clock is enabled/disabled using PCER/PCDR resgisters.
Each peripheral is given an id (see atmel's datasheets) which is used to
define and reference peripheral clocks.
Some new SoCs (at91sam9x5 and sama5d3) provide a new register (PCR) where you
can configure the peripheral clock as a division of the master clock.
This will help reducing the peripherals power comsumption.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com> Acked-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Boris BREZILLON [Fri, 11 Oct 2013 09:41:41 +0000 (11:41 +0200)]
clk: at91: add PMC system clocks
This patch adds new at91 system clock implementation using common clk
framework.
Some peripherals need to enable a "system" clock in order to work properly.
Each system clock is given an id based on the bit position in SCER/SCDR
registers.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com> Acked-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Boris BREZILLON [Fri, 11 Oct 2013 08:51:23 +0000 (10:51 +0200)]
clk: at91: add PMC master clock
This patch adds new at91 master clock implementation using common clk
framework.
The master clock layout describe the MCKR register layout.
There are 2 master clock layouts:
- at91rm9200
- at91sam9x5
Master clocks are given characteristics:
- min/max clock output rate
These characteristics are checked during rate change to avoid
over/underclocking.
These characteristics are described in atmel's SoC datasheet in
"Electrical Characteristics" paragraph.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com> Acked-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Boris BREZILLON [Fri, 11 Oct 2013 08:48:26 +0000 (10:48 +0200)]
clk: at91: add PMC pll clocks
This patch adds new at91 pll clock implementation using common clk framework.
The pll clock layout describe the PLLX register layout.
There are four pll clock layouts:
- at91rm9200
- at91sam9g20
- at91sam9g45
- sama5d3
PLL clocks are given characteristics:
- min/max clock source rate
- ranges of valid clock output rates
- values to set in out and icpll fields for each supported output range
These characteristics are checked during rate change to avoid
over/underclocking.
These characteristics are described in atmel's SoC datasheet in
"Electrical Characteristics" paragraph.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com> Acked-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Boris BREZILLON [Fri, 11 Oct 2013 08:44:49 +0000 (10:44 +0200)]
clk: at91: add PMC main clock
This patch adds new at91 main oscillator clock implementation using common
clk framework.
If rate is not provided during clock registration it is calculated using
the slow clock (main clk parent in this case) rate and MCFR register.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com> Acked-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Boris BREZILLON [Fri, 11 Oct 2013 08:41:25 +0000 (10:41 +0200)]
clk: at91: add PMC macro file for dt definitions
This patch adds a new macro file for PMC macros.
This macro file includes the definitions of SR (status register) bit
offsets and will be use to reference PMC irqs.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com> Acked-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Boris BREZILLON [Mon, 2 Dec 2013 14:07:02 +0000 (15:07 +0100)]
clk: at91: add PMC base support
This patch adds at91 PMC (Power Management Controller) base support.
All at91 clocks managed by the PMC unit will use this framework.
This framework provides the following fonctionalities:
- define a new struct at91_pmc to hide PMC internals (lock, PMC memory
mapping, irq domain, ...)
- read/write helper functions (pmc_read/write) to access PMC registers
- lock/unlock helper functions (pmc_lock/unlock) to lock/unlock access to
pmc registers
- a new irq domain and its associated irq chip to request PMC specific
interrupts (useful for clk prepare callbacks)
The PMC unit is declared as a dt clk provider (CLK_OF_DECLARE), and every
clk using this framework will declare a table of of_at91_clk_init_cb_t
and add it to the pmc_clk_ids table.
When the pmc dt clock setup function is called (by of_clk_init function),
it triggers the registration of every supported child clk (those matching
the definitions in pmc_clk_ids).
This patch copies at91_pmc_base (memory mapping) and at91sam9_idle
(function) from arch/arm/mach-at91/clock.c (which is not compiled if
COMMON_CLK_AT91 is enabled).
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com> Acked-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Boris BREZILLON [Fri, 11 Oct 2013 07:37:46 +0000 (09:37 +0200)]
ARM: at91: add Kconfig options for common clk support
This patch adds the following Kconfig options to prepare the transition to
common clk framework:
- AT91_USE_OLD_CLK: this option is selected by every SoC which does not
support new at91 clks based on common clk framework (SoC which does not
define the clock tree in its device tree).
This options is also selected when the user choose non dt boards support
(new at91 clks can only be registered from a device tree definition).
- COMMON_CLK_AT91: this option cannot be selected directly. Instead it is
enabled if these 3 conditions are met:
* at least one of the selected SoCs have a PMC (Power Management
Controller) Unit
* device tree support is enabled
* the old at91 clk implementation is disabled (every selected SoC define
its clks in its device tree and non dt boards support is disabled)
- OLD_CLK_AT91: this option cannot be selected directly. Instead it is
enabled if these 2 conditions are met:
* at least one of the selected SoCs have a PMC (Power Management
Controller) Unit
* at least one of the selected SoCs does not define its clks in its
device tree or non dt-boards support is enabled
This patch selects AT91_USE_OLD_CLK in all currently supported SoCs. These
selects will be removed after clk definitions are properly added in each
soc's device tree.
It also selects AT91_USE_OLD_CLK in all non-dt boards support.
AT91_PMC_UNIT references are replaced by OLD_CLK_AT91, because PMC Unit is
enabled for both old and common clk implementations, and old clk
implementation should not be compiled if COMMON_CLK is enabled.
To avoid future link errors, a new stub is created for at91_dt_clock_init
function if OLD_CLK_AT91 is disabled.
A new check is added in dt init functions (setup.c) to prepare for SoCs
supporting new clk implementation. These SoCs won't setup the
register_clocks callback (clk registration is done using of_clk_init).
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com> Acked-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Boris BREZILLON [Fri, 11 Oct 2013 07:37:45 +0000 (09:37 +0200)]
ARM: at91: move at91_pmc.h to include/linux/clk/at91_pmc.h
This patch moves at91_pmc.h header from machine specific directory
(arch/arm/mach-at91/include/mach/at91_pmc.h) to clk include directory
(include/linux/clk/at91_pmc.h).
We need this to avoid reference to machine specific headers in clk
drivers.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com> Acked-by: Felipe Balbi <balbi@ti.com> Acked-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Linus Torvalds [Fri, 29 Nov 2013 17:57:13 +0000 (09:57 -0800)]
Merge tag 'arm64-stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64
Pull ARM64 fixes from Catalin Marinas:
- Remove preempt_count modifications in the arm64 IRQ handling code
since that's already dealt with in generic irq_enter/irq_exit
- PTE_PROT_NONE bit moved higher up to avoid overlapping with the
hardware bits (for PROT_NONE mappings which are pte_present)
- Big-endian fixes for ptrace support
- Asynchronous aborts unmasking while in the kernel
- pgprot_writecombine() change to create Normal NonCacheable memory
rather than Device GRE
* tag 'arm64-stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
arm64: Move PTE_PROT_NONE higher up
arm64: Use Normal NonCacheable memory for writecombine
arm64: debug: make aarch32 bkpt checking endian clean
arm64: ptrace: fix compat registes get/set to be endian clean
arm64: Unmask asynchronous aborts when in kernel mode
arm64: dts: Reserve the memory used for secondary CPU release address
arm64: let the core code deal with preempt_count
Linus Torvalds [Fri, 29 Nov 2013 17:56:15 +0000 (09:56 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Martin Schwidefsky:
"One performance improvement and a few bug fixes. Two of the fixes
deal with the clock related problems we have seen on recent kernels"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/mm: handle asce-type exceptions as normal page fault
s390,time: revert direct ktime path for s390 clockevent device
s390/time,vdso: convert to the new update_vsyscall interface
s390/uaccess: add missing page table walk range check
s390/mm: optimize copy_page
s390/dasd: validate request size before building CCW/TCW request
s390/signal: always restore saved runtime instrumentation psw bit
Linus Torvalds [Fri, 29 Nov 2013 17:55:13 +0000 (09:55 -0800)]
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Some easy but needed fixes for i2c drivers since rc1"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: bcm2835: Linking platform nodes to adapter nodes
i2c: omap: raw read and write endian fix
i2c: i2c-bcm-kona: Fix module build
i2c: i2c-diolan-u2c: different usb endpoints for DLN-2-U2C
i2c: bcm-kona: remove duplicated include
i2c: davinci: raw read and write endian fix
Linus Torvalds [Fri, 29 Nov 2013 17:49:08 +0000 (09:49 -0800)]
Merge branch 'for-3.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull workqueue fixes from Tejun Heo:
"This contains one important fix. The NUMA support added a while back
broke ordering guarantees on ordered workqueues. It was enforced by
having single frontend interface with @max_active == 1 but the NUMA
support puts multiple interfaces on unbound workqueues on NUMA
machines thus breaking the ordered guarantee. This is fixed by
disabling NUMA support on ordered workqueues.
The above and a couple other patches were sitting in for-3.12-fixes
but I forgot to push that out, so they ended up waiting a bit too
long. My aplogies.
Other fixes are minor"
* 'for-3.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: fix pool ID allocation leakage and remove BUILD_BUG_ON() in init_workqueues
workqueue: fix comment typo for __queue_work()
workqueue: fix ordered workqueues in NUMA setups
workqueue: swap set_cpus_allowed_ptr() and PF_NO_SETAFFINITY
Linus Torvalds [Fri, 29 Nov 2013 17:48:25 +0000 (09:48 -0800)]
Merge branch 'for-3.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"libata device removal path was removing parent device node before its
child, which is mostly harmless but triggers warning after recent
sysfs changes. Rafael's patch fixes the order.
Other than that, minor controller-specific fixes and device ID
additions"
* 'for-3.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ATA: Fix port removal ordering
ahci: add Marvell 9230 to the AHCI PCI device list
ata: fix acpi_bus_get_device() return value check
pata_arasan_cf: add missing clk_disable_unprepare() on error path
ahci: add support for IBM Akebono platform device
Linus Torvalds [Fri, 29 Nov 2013 17:47:06 +0000 (09:47 -0800)]
Merge branch 'for-3.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup fixes from Tejun Heo:
"Fixes for three issues.
- cgroup destruction path could swamp system_wq possibly leading to
deadlock. This actually seems to happen in the wild with memcg
because memcg destruction path adds nested dependency on system_wq.
Resolved by isolating cgroup destruction work items on its
dedicated workqueue.
- Possible locking context deadlock through seqcount reported by
lockdep
- Memory leak under certain conditions"
* 'for-3.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: fix cgroup_subsys_state leak for seq_files
cpuset: Fix memory allocator deadlock
cgroup: use a dedicated workqueue for cgroup destruction
Linus Torvalds [Fri, 29 Nov 2013 17:36:42 +0000 (09:36 -0800)]
Merge tag 'sound-3.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Quite a few HD-Audio fixes, a WUSB audio fix and a fix for FireWire
audio. The HD-audio part contains a couple of fixes for the generic
parser, and these are the only intrusive fixes. The rest are mostly
device-specific fixes"
* tag 'sound-3.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Add LFE chmap to ASUS ET2700
ALSA: hda - Initialize missing bass speaker pin for ASUS AIO ET2700
ALSA: hda - limit mic boost on Asus UX31[A,E]
ALSA: hda - Check leaf nodes to find aamix amps
ALSA: hda - Fix hp-mic mode without VREF bits
ALSA: hda - Create Headhpone Mic Jack Mode when really needed
ALSA: usb: use multiple packets per urb for Wireless USB inbound audio
ALSA: hda - Enable mute/mic-mute LEDs for more Thinkpads with Conexant codec
ALSA: hda - Drop bus->avoid_link_reset flag
ALSA: hda/realtek - Set pcbeep amp for ALC668
ALSA: hda/realtek - Add support of ALC231 codec
ALSA: firewire-lib: fix wrong value for FDF field as an empty packet
Linus Torvalds [Fri, 29 Nov 2013 17:27:19 +0000 (09:27 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs dentry reference count fix from Al Viro.
This fixes a possible inode_permission NULL pointer dereference (and
other problems) that were due to the root dentry count being decremented
too much. In commit 48a066e72d97 ("RCU'd vfsmounts") the placement of
clearing the LOOKUP_RCU bit changed, and we then returned failure of
incrementing the lockref on the parent dentry with LOOKUP_RCU cleared.
But that meant we needed to go through the same cleanup routines that
the later failures did wrt LOOKUP_ROOT and nd->root.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fix bogus path_put() of nd->root after some unlazy_walk() failures
Catalin Marinas [Wed, 27 Nov 2013 16:59:27 +0000 (16:59 +0000)]
arm64: Move PTE_PROT_NONE higher up
PTE_PROT_NONE means that a pte is present but does not have any
read/write attributes. However, setting the memory type like
pgprot_writecombine() is allowed and such bits overlap with
PTE_PROT_NONE. This causes mmap/munmap issues in drivers that change the
vma->vm_pg_prot on PROT_NONE mappings.
This patch reverts the PTE_FILE/PTE_PROT_NONE shift in commit 59911ca4325d (ARM64: mm: Move PTE_PROT_NONE bit) and moves PTE_PROT_NONE
together with the other software bits.
Signed-off-by: Steve Capper <steve.capper@linaro.org> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Tested-by: Steve Capper <steve.capper@linaro.org> Cc: <stable@vger.kernel.org> # 3.11+
Catalin Marinas [Fri, 29 Nov 2013 10:56:14 +0000 (10:56 +0000)]
arm64: Use Normal NonCacheable memory for writecombine
This provides better performance compared to Device GRE and also allows
unaligned accesses. Such memory is intended to be used with standard RAM
(e.g. framebuffers) and not I/O.
Al Viro [Fri, 29 Nov 2013 06:48:32 +0000 (01:48 -0500)]
fix bogus path_put() of nd->root after some unlazy_walk() failures
Failure to grab reference to parent dentry should go through the
same cleanup as nd->seq mismatch. As it is, we might end up with
caller thinking it needs to path_put() nd->root, with obvious
nasty results once we'd hit that bug enough times to drive the
refcount of root dentry all the way to zero...
Linus Torvalds [Thu, 28 Nov 2013 17:57:46 +0000 (09:57 -0800)]
Merge tag 'gpio-v3.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Here us a bunch of patches for the v3.13 series. Most important stuff
is related to fixes and documentation for the new GPIO descriptor API.
If the diffstat is scary you'll notice most of it is to
Documentation/*:
- A big slew of documentation for the gpiod transition that happened
in the merge window, no semantic effect, but we should provide
proper documentation with the new API.
- Fix flags related to the new API.
- Fix to the find_chip_by_name() lookup function related to the new
API.
- Fix of_find_gpio() when not using device tree.
- Bug fix for the TB10x direction setting.
- Error path fixes from Dan Carpenter.
- Nasty IRQdomain bug relating to taking an unitialized spinlock.
- Minor fixes here and there"
* tag 'gpio-v3.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: bcm281xx: Fix return value of bcm_kona_gpio_get()
gpio: pl061: move irqdomain initialization
gpio: ucb1400: Add MODULE_ALIAS
gpiolib: fix of_find_gpio() when OF not defined
gpio: fix memory leak in error path
gpio: rcar: NULL dereference on error in probe()
gpio: msm: make msm_gpio.summary_irq signed for error handling
gpio: mvebu: make mvchip->irqbase signed for error handling
gpiolib: use dedicated flags for GPIO properties
gpiolib: fix find_chip_by_name()
Documentation: gpiolib: document new interface
gpio: tb10x: Set output value before setting direction to output
Linus Torvalds [Thu, 28 Nov 2013 17:51:39 +0000 (09:51 -0800)]
Merge tag 'md/3.13-fixes' of git://neil.brown.name/md
Pull md fixes from Neil Brown:
"Three bug fixes for md in 3.13-rc
All recent regressions, one in 3.12 so marked for -stable"
* tag 'md/3.13-fixes' of git://neil.brown.name/md:
md/raid5: fix newly-broken locking in get_active_stripe.
md: test mddev->flags more safely in md_check_recovery.
md/raid5: fix new memory-reference bug in alloc_thread_groups.
Linus Torvalds [Thu, 28 Nov 2013 17:50:25 +0000 (09:50 -0800)]
Merge branch 'for-next' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"SMB3 "validate negotiate" is needed to prevent certain types of
downgrade attacks.
Also changes SMB2/SMB3 copy offload from using the BTRFS copy ioctl
(BTRFS_IOC_CLONE) to a cifs specific ioctl (CIFS_IOC_COPYCHUNK_FILE)
to address Christoph's comment that there are semantic differences
between requesting copy offload in which copy-on-write is mandatory
(as in the BTRFS ioctl) and optional in the SMB2/SMB3 case. Also
fixes SMB2/SMB3 copychunk for large files"
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
[CIFS] Do not use btrfs refcopy ioctl for SMB2 copy offload
Check SMB3 dialects against downgrade attacks
Removed duplicated (and unneeded) goto
CIFS: Fix SMB2/SMB3 Copy offload support (refcopy) for large files
Helge Deller [Thu, 28 Nov 2013 08:16:33 +0000 (09:16 +0100)]
kernel/extable: fix address-checks for core_kernel and init areas
The init_kernel_text() and core_kernel_text() functions should not
include the labels _einittext and _etext when checking if an address is
inside the .text or .init sections.
Takashi Iwai [Thu, 28 Nov 2013 14:21:21 +0000 (15:21 +0100)]
ALSA: hda - Initialize missing bass speaker pin for ASUS AIO ET2700
Add a fixup entry for the missing bass speaker pin 0x16 on ASUS ET2700
AiO desktop. The channel map will be added in the next patch, so that
this can be backported easily to stable kernels.
Takashi Iwai [Thu, 28 Nov 2013 10:05:28 +0000 (11:05 +0100)]
ALSA: hda - Check leaf nodes to find aamix amps
The current generic parser assumes blindly that the volume and mute
amps are found in the aamix node itself. But on some codecs,
typically Analog Devices ones, the aamix amps are separately
implemented in each leaf node of the aamix node, and the current
driver can't establish the correct amp controls. This is a regression
compared with the previous static quirks.
This patch extends the search for the amps to the leaf nodes for
allowing the aamix controls again on such codecs.
In this implementation, I didn't code to loop through the whole paths,
since usually one depth should suffice, and we can't search too
deeply, as it may result in the conflicting control assignments.
Florian Meier [Mon, 25 Nov 2013 08:01:50 +0000 (09:01 +0100)]
i2c: bcm2835: Linking platform nodes to adapter nodes
In order to find I2C devices in the device tree, the platform nodes
have to be known by the I2C core. This requires setting the
dev.of_node parameter of the adapter.
Signed-off-by: Florian Meier <florian.meier@koalo.de> Tested-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Laurent Pinchart [Mon, 28 Oct 2013 22:49:27 +0000 (23:49 +0100)]
usb: r8a66597-hcd: Convert to clk_prepare/unprepare
Turn clk_enable() and clk_disable() calls into clk_prepare_enable() and
clk_disable_unprepare() to get ready for the migration to the common
clock framework.
Linus Torvalds [Thu, 28 Nov 2013 05:06:01 +0000 (21:06 -0800)]
Merge tag 'tty-3.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some tty/serial driver fixes for reported issues in 3.13-rc2.
The n_gsm "fix" was reverted as it was found to not be correct.
Hopefully this will be resolved in a future pull request, but as
there's really only one user of this line setting, it's not a big
deal..."
* tag 'tty-3.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "n_gsm: race between ld close and gsmtty open"
n_tty: Protect minimum_to_wake reset for concurrent readers
tty: Reset hupped state on open
TTY: amiserial, add missing platform check
TTY: pmac_zilog, check existence of ports in pmz_console_init()
n_gsm: race between ld close and gsmtty open
tty/serial/8250: fix typo in help text
n_tty: Fix 4096-byte canonical reads
n_tty: Fix echo overrun tail computation
n_tty: Ensure reader restarts worker for next reader
Linus Torvalds [Thu, 28 Nov 2013 05:05:31 +0000 (21:05 -0800)]
Merge tag 'staging-3.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging fixes from Greg KH:
"Here are a number of staging, and IIO driver, fixes for 3.13-rc2 that
resolve issues that have been reported for 3.13-rc1. All of these
have been in linux-next for a bit this week"
* tag 'staging-3.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (25 commits)
Staging: tidspbridge: disable driver
staging: zsmalloc: Ensure handle is never 0 on success
staging/lustre/ptlrpc: fix ptlrpc_stop_pinger logic
staging: r8188eu: Fix AP mode
Staging: btmtk_usb: Add hdev parameter to hdev->send driver callback
Staging: go7007: fix up some remaining go->dev issues
staging: imx-drm: Fix modular build of DRM_IMX_IPUV3
staging: ft1000: fix use of potentially uninitialized variable
Revert "staging:media: Use dev_dbg() instead of pr_debug()"
Staging: zram: Fix memory leak by refcount mismatch
staging: vt6656: [BUG] Fix for TX USB resets from vendors driver.
staging: nvec: potential NULL dereference on error path
Staging: vt6655-6: potential NULL dereference in hostap_disable_hostapd()
staging: comedi: s626: fix value written by s626_set_dac()
Staging: comedi: pcl730: fix some bitwise vs logical AND bugs
staging: comedi: fix potentially uninitialised variable
iio:accel:kxsd9 fix missing mutex unlock
iio: adc: ti_am335x_adc: avoid double free of buffer.
staging:iio: Fix hmc5843 Kconfig dependencies
iio: Fix tcs3472 Kconfig dependencies
...
Linus Torvalds [Thu, 28 Nov 2013 05:04:37 +0000 (21:04 -0800)]
Merge tag 'driver-core-3.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are 3 patches for sysfs issues that have been reported. Well, 1
patch really, the first one is reverted as it's not really needed (the
correct fix is coming in through the different driver subsystems
instead)
But that 1 sysfs fix is needed, so this is still a good thing to pull
in now"
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'driver-core-3.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
Revert "sysfs: handle duplicate removal attempts in sysfs_remove_group()"
sysfs: use a separate locking class for open files depending on mmap
sysfs: handle duplicate removal attempts in sysfs_remove_group()
Linus Torvalds [Thu, 28 Nov 2013 04:41:54 +0000 (20:41 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
- fix compat ioctl leak in uhid, by David Herrmann
- fix scheduling in atomic context (causing actual lockups in real
world) in hid-sony driver, by Sven Eckelmann
- revert patch introducing VID/PID conflict, by Jiri Kosina
- support from various new device IDs by Benjamin Tissoires and
KaiChung Cheng
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: uhid: fix leak for 64/32 UHID_CREATE
HID: kye: fix unresponsive keyboard
HID: kye: Add report fixup for Genius Manticore Keyboard
HID: multicouh: add PID VID to support 1 new Wistron optical touch device
HID: appleir: force input to be set
Revert "HID: wiimote: add LEGO-wiimote VID"
HID: sony: Send FF commands in non-atomic context
Linus Torvalds [Thu, 28 Nov 2013 04:40:35 +0000 (20:40 -0800)]
Merge tag 'pm+acpi-3.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
- Fix for a recent regression in the Tegra cpufreq driver causing
excess error messages to be printed from Stephen Warren
- ACPI-based device hotplug fix to prevent conflicting notify handlers
from being installed for PCI host bridge objects. From Toshi Kani
- ACPICA update to upstream version 20131115. This contains bug fixes
mostly (loop termination fix for the get AML length function, fixes
related to namespace node removal and debug output). From Bob Moore,
Tomasz Nowicki and Lv Zheng
- Removal of incorrect inclusions of internal ACPICA header files by
non-ACPICA code from Lv Zheng
- Fixes for the ACPI sysfs interface exposing tables to user space from
Daisuke Hatayama and Jeremy Compostella
- Assorted ACPI and cpufreq cleanups from Sachin Kamat and Al Stone
- cpupower tool fix and man page from Thomas Renninger
* tag 'pm+acpi-3.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: Clean up incorrect inclusions of ACPICA headers
tools: cpupower: fix wrong err msg not supported vs not available
tools: cpupower: Add cpupower-idle-set(1) manpage
ACPI / sysfs: Fix incorrect ACPI tables walk in acpi_tables_sysfs_init()
ACPI / sysfs: Set file size for each exposed ACPI table
ACPICA: Update version to 20131115.
ACPICA: Add support to delete all objects attached to the root namespace node.
ACPICA: Delete all attached data objects during namespace node deletion.
ACPICA: Resources: Fix loop termination for the get AML length function.
ACPICA: Tests: Add CHECKSUM_ABORT protection for test utilities.
ACPICA: Debug output: Do not emit function nesting level for kernel build.
ACPI / sleep: clean up compiler warning about uninitialized field
cpufreq: exynos: Remove unwanted EXPORT_SYMBOL
cpufreq: tegra: don't error target() when suspended
ACPI / hotplug: Fix conflicted PCI bridge notify handlers
Ilia Mirkin [Wed, 27 Nov 2013 17:38:42 +0000 (12:38 -0500)]
drm/nouveau/hwmon: fix compilation without CONFIG_HWMON
Reported-by: Jim Davis <jim.epost@gmail.com> Tested-by: Jim Davis <jim.epost@gmail.com> Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu> Signed-off-by: Dave Airlie <airlied@redhat.com>
David Herrmann [Tue, 26 Nov 2013 11:50:50 +0000 (12:50 +0100)]
drm/sysfs: fix OOM verification
Copy/Paste typo.. we need to test for ->kdev instead of ->dev.
Reported-by: Juha Leppänen <juha_efku@dnainternet.net> Signed-off-by: David Herrmann <dh.herrmann@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Linus Torvalds [Thu, 28 Nov 2013 04:32:38 +0000 (20:32 -0800)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc fixes from Ben Herrenschmidt:
"The main thing that caused problem was that CONFIG_CPU_LITTLE_ENDIAN
got turned on with allyesconfig and such, which is not a very good
idea especially since it requires a newer toolchain than what most
people have.
So we turned it into a choice instead that defaults to big endian"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/windfarm: Fix XServe G5 fan control Makefile issue
arch/powerpc/kernel: Use %12.12s instead of %12s to avoid memory overflow
powerpc/signals: Improved mark VSX not saved with small contexts fix
powerpc/kdump: Adding symbols in vmcoreinfo to facilitate dump filtering
powerpc: allyesconfig should not select CONFIG_CPU_LITTLE_ENDIAN
powerpc: Fix error when cross building TAGS & cscope
powerpc/booke: Only check for hugetlb in flush if vma != NULL
powerpc/85xx: typo in dts: "interupt" (four devices)
powerpc/8xx: mfspr SPRN_TBRx in lieu of mftb/mftbu is not supported
powerpc/corenet64: compile with CONFIG_E{5,6}500_CPU well
NeilBrown [Wed, 27 Nov 2013 23:55:27 +0000 (10:55 +1100)]
md/raid5: fix newly-broken locking in get_active_stripe.
commit 566c09c53455d7c4f1 raid5: relieve lock contention in get_active_stripe()
modified the locking in get_active_stripe() reducing the range
protected by the (highly contended) device_lock.
Unfortunately it reduced the range too much opening up some races.
One race can occur if get_priority_stripe runs between the
test on sh->count and device_lock being taken.
This will mean that sh->lru is not empty while get_active_stripe
thinks ->count is zero resulting in a 'BUG' firing.
Another race happens if __release_stripe is called immediately
after sh->count is tested and found to be non-zero. If STRIPE_HANDLE
is not set, get_active_stripe should increment ->active_stripes
when it increments ->count from 0, but as it didn't think it was 0,
it doesn't.
Extending device_lock to cover the test on sh->count close these
races.
While we are here, fix the two BUG tests:
-If count is zero, then lru really must not be empty, or we've
lock the stripe_head somehow - no other tests are relevant.
-STRIPE_ON_RELEASE_LIST is completely independent of ->lru so
testing it is pointless.
Reported-and-tested-by: Brassow Jonathan <jbrassow@redhat.com> Reviewed-by: Shaohua Li <shli@kernel.org> Fixes: 566c09c53455d7c4f1 Signed-off-by: NeilBrown <neilb@suse.de>
NeilBrown [Wed, 27 Nov 2013 23:34:18 +0000 (10:34 +1100)]
md: test mddev->flags more safely in md_check_recovery.
commit 7a0a5355cbc71efa md: Don't test all of mddev->flags at once.
made most tests on mddev->flags safer, but missed one.
When
commit 260fa034ef7a4ff8b7306 md: avoid deadlock when dirty buffers during md_stop.
added MD_STILL_CLOSED, this caused md_check_recovery to misbehave.
It can think there is something to do but find nothing. This can
lead to the md thread spinning during array shutdown.
https://bugzilla.kernel.org/show_bug.cgi?id=65721
Reported-and-tested-by: Richard W.M. Jones <rjones@redhat.com> Fixes: 260fa034ef7a4ff8b7306 Cc: stable@vger.kernel.org (3.12) Signed-off-by: NeilBrown <neilb@suse.de>
NeilBrown [Mon, 25 Nov 2013 00:12:43 +0000 (11:12 +1100)]
md/raid5: fix new memory-reference bug in alloc_thread_groups.
In alloc_thread_groups, worker_groups is a pointer to an array,
not an array of pointers.
So
worker_groups[i]
is wrong. It should be
&(*worker_groups)[i]
Tejun Heo [Wed, 27 Nov 2013 23:16:21 +0000 (18:16 -0500)]
cgroup: fix cgroup_subsys_state leak for seq_files
If a cgroup file implements either read_map() or read_seq_string(),
such file is served using seq_file by overriding file->f_op to
cgroup_seqfile_operations, which also overrides the release method to
single_release() from cgroup_file_release().
Because cgroup_file_open() didn't use to acquire any resources, this
used to be fine, but since f7d58818ba42 ("cgroup: pin
cgroup_subsys_state when opening a cgroupfs file"), cgroup_file_open()
pins the css (cgroup_subsys_state) which is put by
cgroup_file_release(). The patch forgot to update the release path
for seq_files and each open/release cycle leaks a css reference.
Fix it by updating cgroup_file_release() to also handle seq_files and
using it for seq_file release path too.
After commit bcdde7e221a8 (sysfs: make __sysfs_remove_dir() recursive)
Mika Westerberg sees traces analogous to the one below in Thunderbolt
hot-remove testing:
The source of this problem is that SCSI hosts are removed from
ATA ports after calling ata_tport_delete() which removes the
port's sysfs directory, among other things. Now, after commit bcdde7e221a8, the sysfs directory is removed along with all of
its subdirectories that include the SCSI host's sysfs directory
and its subdirectories at this point. Consequently, when
device_del() is finally called for any child device of the SCSI
host and tries to remove its "power" group (which is already
gone then), it triggers the above warning.
To make the warnings go away, change the removal ordering in
ata_port_detach() so that the SCSI host is removed from the
port before ata_tport_delete() is called.
References: https://bugzilla.kernel.org/show_bug.cgi?id=65281 Reported-and-tested-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Tested-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Tejun Heo <tj@kernel.org>
Which reports that we take mems_allowed_seq with interrupts enabled. A
little digging found that this can only be from
cpuset_change_task_nodemask().
This is an actual deadlock because an interrupt doing an allocation will
hit get_mems_allowed()->...->__read_seqcount_begin(), which will spin
forever waiting for the write side to complete.
Cc: John Stultz <john.stultz@linaro.org> Cc: Mel Gorman <mgorman@suse.de> Reported-by: Juri Lelli <juri.lelli@gmail.com> Signed-off-by: Peter Zijlstra <peterz@infradead.org> Tested-by: Juri Lelli <juri.lelli@gmail.com> Acked-by: Li Zefan <lizefan@huawei.com> Acked-by: Mel Gorman <mgorman@suse.de> Signed-off-by: Tejun Heo <tj@kernel.org> Cc: stable@vger.kernel.org
Victor Kamensky [Wed, 27 Nov 2013 13:48:08 +0000 (15:48 +0200)]
i2c: omap: raw read and write endian fix
All OMAP IP blocks expect LE data, but CPU may operate in BE mode.
Need to use endian neutral functions to read/write h/w registers.
I.e instead of __raw_read[lw] and __raw_write[lw] functions code
need to use read[lw]_relaxed and write[lw]_relaxed functions.
If the first simply reads/writes register, the second will byteswap
it if host operates in BE mode.
Changes are trivial sed like replacement of __raw_xxx functions
with xxx_relaxed variant.
Signed-off-by: Victor Kamensky <victor.kamensky@linaro.org> Signed-off-by: Taras Kondratiuk <taras.kondratiuk@linaro.org> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The root cause of these "inverted" sysfs removals have now been found,
so there is no need for this patch. Keep this functionality around so
that this type of error doesn't show up in driver code again.
Cc: Mika Westerberg <mika.westerberg@linux.intel.com> Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / ~andy / linux / log