This addresses regression caused by commit id "751d17e23a9f7"
iio: hid-sensors: Fix power and report state.
This commit removed a quirk, to change the enumeration base
to 1 from 0 based on an CONFIG paramter. There was objection to
add more changes under this quirk, instead suggested to add an
HID quirk. But there is no easy way to add HID qurik as the
reports are not properly using collection class.
The solution was to use logical minimum, which is a correct way.
There were changes done in firmware to address this.
Unfortunately some devices, still use old FW and can't be upgraded
to newer version on Linux devices as there is no FW upgrade tool
available for Linux devices. So we need to fix report descriptors,
for such devices. This will not have any impact, if the FW uses
logical 1 as minimum.
In this patch we look for usage id for "power and report state", and
modify logical minimum value to 1.
Background on enum:
In the original HID sensor hub firmwares all Named array enums were
to 0-based. But the most recent hub implemented as 1-based,
because of the implementation by one of the major OS vendor.
Using logical minimum for the field as the base of enum. So we add
logical minimum to the selector values before setting those fields.
Some sensor hub FWs already changed logical minimum from 0 to 1
to reflect this and hope every other vendor will follow.
There is no easy way to add a common HID quirk for NAry elements,
even if the standard specifies these field as NAry, the collection
used to describe selectors is still just "logical".
This fix (not very clean though) should fix the long time USB3
issue that was spotted last year. The rational has been given by
Hans de Goede:
----
I think the most likely cause for this is a firmware bug
in the unifying receiver, likely a race condition.
The most prominent difference between having a USB-2 device
plugged into an EHCI (so USB-2 only) port versus an XHCI
port will be inter packet timing. Specifically if you
send packets (ie hid reports) one at a time, then with
the EHCI controller their will be a significant pause
between them, where with XHCI they will be very close
together in time.
The reason for this is the difference in EHCI / XHCI
controller OS <-> driver interfaces.
For non periodic endpoints (control, bulk) the EHCI uses a
circular linked-list of commands in dma-memory, which it
follows to execute commands, if the list is empty, it
will go into an idle state and re-check periodically.
The XHCI uses a ring of commands per endpoint, and if the OS
places anything new on the ring it will do an ioport write,
waking up the XHCI making it send the new packet immediately.
For periodic transfers (isoc, interrupt) the delay between
packets when sending one at a time (rather then queuing them
up) will be even larger, because they need to be inserted into
the EHCI schedule 2 ms in the future so the OS driver can be
sure that the EHCI driver does not try to start executing the
time slot in question before the insertion has completed.
So a possible fix may be to insert a delay between packets
being send to the receiver.
----
I tested this on a buggy Haswell USB 3.0 motherboard, and I always
get the notification after adding the msleep.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
we used to set the parent of the input device as the parent of
the hid bus. This was introduced when we created hid as a real bus, and
to keep backward compatibility. Now, it's time to proper set the parent
so that sysfs has an idea of which input device is attached to
which hid device.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
David Herrmann <dh.herrmann@gmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Jiri Kosina [Sun, 15 Dec 2013 17:25:26 +0000 (18:25 +0100)]
HID: microsoft: no fallthrough in MS ergonomy 0xff05 usage
For 0xff05 usage in MS ergonomy keyboard quirk, we are falling through
and returning 0 instread of properly (because we've performed new mapping)
returning 1. Fix that.
Reported-by: Joe Perches <joe@perches.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Linus Torvalds [Fri, 13 Dec 2013 19:39:54 +0000 (11:39 -0800)]
Merge tag 'regulator-v3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A small set of driver fixes plus one larger core change which changes
the way we check to see if we're using DT so that there aren't any
races between deciding we're using DT and the regulator subsystem
noticing.
This makes the new support for substituting a dummy regulator and
optional regulators work a lot better on DT systems since it ensures
that we don't trigger probe deferral when we shouldn't which was
causing bugs in clients"
* tag 'regulator-v3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: pfuze100: allow misprogrammed ID
regulator: pfuze100: Fix address of FABID
regulator: as3722: set the correct current limit
regulator: core: Check for DT every time we check full constraints
regulator: core: Replace checks of have_full_constraints with a function
Linus Torvalds [Fri, 13 Dec 2013 19:38:35 +0000 (11:38 -0800)]
Merge tag 'regmap-v3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fixes from Mark Brown:
"Two small changes to fix some error handling and checking (both of
which would be quite serious if the errors trigger) plus a trivial
documentation fix"
* tag 'regmap-v3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: use IS_ERR() to check clk_get() results
regmap: make sure we unlock on failure in regmap_bulk_write
regmap: trivial comment fix (copy'n'paste error)
Linus Torvalds [Fri, 13 Dec 2013 19:37:57 +0000 (11:37 -0800)]
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Here are two simple but wanted fixes for the i2c subsystem"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: imx: Check the return value from clk_prepare_enable()
i2c: mux: Inherit retry count and timeout from parent for muxed bus
Linus Torvalds [Fri, 13 Dec 2013 19:31:22 +0000 (11:31 -0800)]
Merge tag 'for-linus-20131212' of git://git.infradead.org/linux-mtd
Pull MTD fixes from Brian Norris:
"Two MTD fixes, for the pxa3xx-nand driver:
- This driver was not ready to fully Armada 370 NAND, with
particularly notable problems seen on flash with 2KB page sizes.
This "compatible" entry really should have been held back until
3.14 or later.
- Fix a bug seen in rare cases on the error path of a failed probe
attempt, where we free unallocated DMA resources"
* tag 'for-linus-20131212' of git://git.infradead.org/linux-mtd:
mtd: nand: pxa3xx: Use info->use_dma to release DMA resources
Partially revert "mtd: nand: pxa3xx: Introduce 'marvell,armada370-nand' compatible string"
Linus Torvalds [Fri, 13 Dec 2013 19:29:51 +0000 (11:29 -0800)]
Merge branch 'fixes' of git://git.infradead.org/users/vkoul/slave-dma
Pull slave-dmaengine fixes from Vinod Koul:
"Here is the common fixes PULL for dmaengine.
Dan has been working on fixing the build issues in bunch of drivers.
Here we have one fixing s3c24xx-dma, along with fix from Russell on
pl08x. Also we have Kuninori rcar dma fixes. The s3c24xx-dma which
was added in last merge window missed updates to usage of DMA_COMPLETE
so converting the last driver"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dma: fix build breakage in s3c24xx-dma
Fix pl08x warnings
rcar-hpbdma: initialise plane information when halted
rcar-hpbdma: fixup channel busy check for double plane
rcar-hpbdma: add max transfer size
dma: mmp_pdma: add missing platform_set_drvdata() in mmp_pdma_probe()
dmaengine: s3c24xx-dma: use DMA_COMPLETE for dma completion status
Linus Torvalds [Fri, 13 Dec 2013 02:22:10 +0000 (18:22 -0800)]
Merge branch 'akpm' (fixes from Andrew)
Merge patches from Andrew Morton:
"13 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm: memcg: do not allow task about to OOM kill to bypass the limit
mm: memcg: fix race condition between memcg teardown and swapin
thp: move preallocated PTE page table on move_huge_pmd()
mfd/rtc: s5m: fix register updating by adding regmap for RTC
rtc: s5m: enable IRQ wake during suspend
rtc: s5m: limit endless loop waiting for register update
rtc: s5m: fix unsuccesful IRQ request during probe
drivers/rtc/rtc-s5m.c: fix info->rtc assignment
include/linux/kernel.h: make might_fault() a nop for !MMU
drivers/rtc/rtc-at91rm9200.c: correct alarm over day/month wrap
procfs: also fix proc_reg_get_unmapped_area() for !MMU case
mm: memcg: do not declare OOM from __GFP_NOFAIL allocations
include/linux/hugetlb.h: make isolate_huge_page() an inline
Johannes Weiner [Fri, 13 Dec 2013 01:12:35 +0000 (17:12 -0800)]
mm: memcg: do not allow task about to OOM kill to bypass the limit
Commit 4942642080ea ("mm: memcg: handle non-error OOM situations more
gracefully") allowed tasks that already entered a memcg OOM condition to
bypass the memcg limit on subsequent allocation attempts hoping this
would expedite finishing the page fault and executing the kill.
David Rientjes is worried that this breaks memcg isolation guarantees
and since there is no evidence that the bypass actually speeds up fault
processing just change it so that these subsequent charge attempts fail
outright. The notable exception being __GFP_NOFAIL charges which are
required to bypass the limit regardless.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Reported-by: David Rientjes <rientjes@google.com> Acked-by: Michal Hocko <mhocko@suse.cz>
Acked-bt: David Rientjes <rientjes@google.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johannes Weiner [Fri, 13 Dec 2013 01:12:34 +0000 (17:12 -0800)]
mm: memcg: fix race condition between memcg teardown and swapin
There is a race condition between a memcg being torn down and a swapin
triggered from a different memcg of a page that was recorded to belong
to the exiting memcg on swapout (with CONFIG_MEMCG_SWAP extension). The
result is unreclaimable pages pointing to dead memcgs, which can lead to
anything from endless loops in later memcg teardown (the page is charged
to all hierarchical parents but is not on any LRU list) or crashes from
following the dangling memcg pointer.
Memcgs with tasks in them can not be torn down and usually charges don't
show up in memcgs without tasks. Swapin with the CONFIG_MEMCG_SWAP
extension is the notable exception because it charges the cgroup that
was recorded as owner during swapout, which may be empty and in the
process of being torn down when a task in another memcg triggers the
swapin:
teardown: swapin:
lookup_swap_cgroup_id()
rcu_read_lock()
mem_cgroup_lookup()
css_tryget()
rcu_read_unlock()
disable css_tryget()
call_rcu()
offline_css()
reparent_charges()
res_counter_charge() (hierarchical!)
css_put()
css_free()
pc->mem_cgroup = dead memcg
add page to dead lru
Add a final reparenting step into css_free() to make sure any such raced
charges are moved out of the memcg before it's finally freed.
In the longer term it would be cleaner to have the css_tryget() and the
res_counter charge under the same RCU lock section so that the charge
reparenting is deferred until the last charge whose tryget succeeded is
visible. But this will require more invasive changes that will be
harder to evaluate and backport into stable, so better defer them to a
separate change set.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Acked-by: Michal Hocko <mhocko@suse.cz> Cc: David Rientjes <rientjes@google.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
p = mmap((void *) GB, 10 * MB, PROT_READ | PROT_WRITE,
MAP_PRIVATE | MAP_ANONYMOUS | MAP_FIXED, -1, 0);
for (i = 0; i < 10 * MB; i += 4096)
p[i] = 1;
mremap(p, 10 * MB, 10 * MB, MREMAP_FIXED | MREMAP_MAYMOVE, 2 * GB);
return 0;
}
Due to split PMD lock, we now store preallocated PTE tables for THP
pages per-PMD table. It means we need to move them to other PMD table
if huge PMD moved there.
mfd/rtc: s5m: fix register updating by adding regmap for RTC
Rename old regmap field of "struct sec_pmic_dev" to "regmap_pmic" and
add new regmap for RTC.
On S5M8767A registers were not properly updated and read due to usage of
the same regmap as the PMIC. This could be observed in various hangs,
e.g. in infinite loop during waiting for UDR field change.
On this chip family the RTC has different I2C address than PMIC so
additional regmap is needed.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Reviewed-by: Mark Brown <broonie@linaro.org> Acked-by: Sangbeom Kim <sbkim73@samsung.com> Cc: Samuel Ortiz <sameo@linux.intel.com> Cc: Lee Jones <lee.jones@linaro.org> Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add PM suspend/resume ops to rtc-s5m driver and enable IRQ wake during
suspend so the RTC would act like a wake up source. This allows waking
up from suspend to RAM on RTC alarm interrupt.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Mark Brown <broonie@linaro.org> Acked-by: Sangbeom Kim <sbkim73@samsung.com> Cc: Samuel Ortiz <sameo@linux.intel.com> Cc: Lee Jones <lee.jones@linaro.org> Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
rtc: s5m: limit endless loop waiting for register update
After setting alarm or time the driver is waiting for UDR register to be
cleared indicating that registers data have been transferred.
Limit the endless loop to only 5 retries.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Reviewed-by: Mark Brown <broonie@linaro.org> Acked-by: Sangbeom Kim <sbkim73@samsung.com> Cc: Samuel Ortiz <sameo@linux.intel.com> Cc: Lee Jones <lee.jones@linaro.org> Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
rtc: s5m: fix unsuccesful IRQ request during probe
Probe failed for rtc-s5m:
s5m-rtc s5m-rtc: Failed to request alarm IRQ: 12: -22
s5m-rtc: probe of s5m-rtc failed with error -22
Fix rtc-s5m interrupt request by using regmap_irq_get_virq() for mapping
the IRQ.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Reviewed-by: Mark Brown <broonie@linaro.org> Acked-by: Sangbeom Kim <sbkim73@samsung.com> Cc: Samuel Ortiz <sameo@linux.intel.com> Cc: Lee Jones <lee.jones@linaro.org> Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Kyungmin Park <kyungmin.park@samsung.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Axel Lin [Fri, 13 Dec 2013 01:12:24 +0000 (17:12 -0800)]
include/linux/kernel.h: make might_fault() a nop for !MMU
The machine cannot fault if !MUU, so make might_fault() a nop for !MMU.
This fixes below build error if
!CONFIG_MMU && (CONFIG_PROVE_LOCKING=y || CONFIG_DEBUG_ATOMIC_SLEEP=y):
arch/arm/kernel/built-in.o: In function `arch_ptrace':
arch/arm/kernel/ptrace.c:852: undefined reference to `might_fault'
arch/arm/kernel/built-in.o: In function `restore_sigframe':
arch/arm/kernel/signal.c:173: undefined reference to `might_fault'
...
arch/arm/kernel/built-in.o:arch/arm/kernel/signal.c:177: more undefined references to `might_fault' follow
make: *** [vmlinux] Error 1
Signed-off-by: Axel Lin <axel.lin@ingics.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jan Beulich [Fri, 13 Dec 2013 01:12:22 +0000 (17:12 -0800)]
procfs: also fix proc_reg_get_unmapped_area() for !MMU case
Commit fad1a86e25e0 ("procfs: call default get_unmapped_area on
MMU-present architectures"), as its title says, took care of only the
MMU case, leaving the !MMU side still in the regressed state (returning
-EIO in all cases where pde->proc_fops->get_unmapped_area is NULL).
"Commit c4fe24485729 ("sparc: fix PCI device proc file mmap(2)") added
proc_reg_get_unmapped_area in proc_reg_file_ops and
proc_reg_file_ops_no_compat, by which now mmap always returns EIO if
get_unmapped_area method is not defined for the target procfs file, which
causes regression of mmap on /proc/vmcore.
To address this issue, like get_unmapped_area(), call default
current->mm->get_unmapped_area on MMU-present architectures if
pde->proc_fops->get_unmapped_area, i.e. the one in actual file operation
in the procfs file, is not defined"
Signed-off-by: Jan Beulich <jbeulich@suse.com> Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com> Cc: Alexey Dobriyan <adobriyan@gmail.com> Cc: David S. Miller <davem@davemloft.net> Cc: <stable@vger.kernel.org> [3.12.x] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johannes Weiner [Fri, 13 Dec 2013 01:12:20 +0000 (17:12 -0800)]
mm: memcg: do not declare OOM from __GFP_NOFAIL allocations
Commit 84235de394d9 ("fs: buffer: move allocation failure loop into the
allocator") started recognizing __GFP_NOFAIL in memory cgroups but
forgot to disable the OOM killer.
Any task that does not fail allocation will also not enter the OOM
completion path. So don't declare an OOM state in this case or it'll be
leaked and the task be able to bypass the limit until the next
userspace-triggered page fault cleans up the OOM state.
Reported-by: William Dauchy <wdauchy@gmail.com> Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Acked-by: Michal Hocko <mhocko@suse.cz> Cc: David Rientjes <rientjes@google.com> Cc: <stable@vger.kernel.org> [3.12.x] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Naoya Horiguchi [Fri, 13 Dec 2013 01:12:19 +0000 (17:12 -0800)]
include/linux/hugetlb.h: make isolate_huge_page() an inline
With CONFIG_HUGETLBFS=n:
mm/migrate.c: In function `do_move_page_to_node_array':
include/linux/hugetlb.h:140:33: warning: statement with no effect [-Wunused-value]
#define isolate_huge_page(p, l) false
^
mm/migrate.c:1170:4: note: in expansion of macro `isolate_huge_page'
isolate_huge_page(page, &pagelist);
Linus Torvalds [Thu, 12 Dec 2013 23:45:03 +0000 (15:45 -0800)]
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Another week, another batch of fixes.
Again, OMAP regressions due to move to DT is the bulk of the changes
here, but this should be the last of it for 3.13. There are also a
handful of OMAP hwmod changes (power management, reset handling) for
USB on OMAP3 that fixes some longish-standing bugs around USB resets.
There are a couple of other changes that also add up line count a bit:
One is a long-standing bug with the keyboard layout on one of the PXA
platforms. The other is a fix for highbank that moves their
power-off/reset button handling to be done in-kernel since relying on
userspace to handle it was fragile and awkward"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: sun6i: dt: Fix interrupt trigger types
ARM: sun7i: dt: Fix interrupt trigger types
MAINTAINERS: merge IMX6 entry into IMX
ARM: tegra: add missing break to fuse initialization code
ARM: pxa: prevent PXA270 occasional reboot freezes
ARM: pxa: tosa: fix keys mapping
ARM: OMAP2+: omap_device: add fail hook for runtime_pm when bad data is detected
ARM: OMAP2+: hwmod: Fix usage of invalid iclk / oclk when clock node is not present
ARM: OMAP3: hwmod data: Don't prevent RESET of USB Host module
ARM: OMAP2+: hwmod: Fix SOFTRESET logic
ARM: OMAP4+: hwmod data: Don't prevent RESET of USB Host module
ARM: dts: Fix booting for secure omaps
ARM: OMAP2+: Fix the machine entry for am3517
ARM: dts: Fix missing entries for am3517
ARM: OMAP2+: Fix overwriting hwmod data with data from device tree
ARM: davinci: Fix McASP mem resource names
ARM: highbank: handle soft poweroff and reset key events
ARM: davinci: fix number of resources passed to davinci_gpio_register()
gpio: davinci: fix check for unbanked gpio
Linus Torvalds [Thu, 12 Dec 2013 23:25:10 +0000 (15:25 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"This is a small collection of fixes. It was rebased this morning, but
I was just fixing signed-off-by tags with the wrong email"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix access_ok() check in btrfs_ioctl_send()
Btrfs: make sure we cleanup all reloc roots if error happens
Btrfs: skip building backref tree for uuid and quota tree when doing balance relocation
Btrfs: fix an oops when doing balance relocation
Btrfs: don't miss skinny extent items on delayed ref head contention
btrfs: call mnt_drop_write after interrupted subvol deletion
Btrfs: don't clear the default compression type
mtd: nand: pxa3xx: Allocate data buffer on detected flash size
the way the buffer is allocated was changed: the first READ_ID is issued
with a small kmalloc'ed buffer. Only once the flash page size is detected
the DMA buffers are allocated, and info->use_dma is set.
Currently, if the device detection fails, the driver checks the 'use_dma'
module parameter and tries to release unallocated DMA resources.
Fix this by checking the proper indicator of the DMA allocation, which
is 'info->use_dma'.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The "armada370-nand" compatible support is not complete, and it was mistake
to add it. Revert it and postpone the support until the infrastructure is
in place.
Cc: <stable@vger.kernel.org> # 3.12 Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Acked-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Gleb Natapov [Thu, 12 Dec 2013 20:20:08 +0000 (21:20 +0100)]
KVM: x86: fix guest-initiated crash with x2apic (CVE-2013-6376)
A guest can cause a BUG_ON() leading to a host kernel crash.
When the guest writes to the ICR to request an IPI, while in x2apic
mode the following things happen, the destination is read from
ICR2, which is a register that the guest can control.
kvm_irq_delivery_to_apic_fast uses the high 16 bits of ICR2 as the
cluster id. A BUG_ON is triggered, which is a protection against
accessing map->logical_map with an out-of-bounds access and manages
to avoid that anything really unsafe occurs.
The logic in the code is correct from real HW point of view. The problem
is that KVM supports only one cluster with ID 0 in clustered mode, but
the code that has the bug does not take this into account.
Reported-by: Lars Bull <larsbull@google.com> Cc: stable@vger.kernel.org Signed-off-by: Gleb Natapov <gleb@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Andy Honig [Wed, 20 Nov 2013 18:23:22 +0000 (10:23 -0800)]
KVM: x86: Convert vapic synchronization to _cached functions (CVE-2013-6368)
In kvm_lapic_sync_from_vapic and kvm_lapic_sync_to_vapic there is the
potential to corrupt kernel memory if userspace provides an address that
is at the end of a page. This patches concerts those functions to use
kvm_write_guest_cached and kvm_read_guest_cached. It also checks the
vapic_address specified by userspace during ioctl processing and returns
an error to userspace if the address is not a valid GPA.
This is generally not guest triggerable, because the required write is
done by firmware that runs before the guest. Also, it only affects AMD
processors and oldish Intel that do not have the FlexPriority feature
(unless you disable FlexPriority, of course; then newer processors are
also affected).
Fixes: b93463aa59d6 ('KVM: Accelerated apic support') Reported-by: Andrew Honig <ahonig@google.com> Cc: stable@vger.kernel.org Signed-off-by: Andrew Honig <ahonig@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Andy Honig [Tue, 19 Nov 2013 22:12:18 +0000 (14:12 -0800)]
KVM: x86: Fix potential divide by 0 in lapic (CVE-2013-6367)
Under guest controllable circumstances apic_get_tmcct will execute a
divide by zero and cause a crash. If the guest cpuid support
tsc deadline timers and performs the following sequence of requests
the host will crash.
- Set the mode to periodic
- Set the TMICT to 0
- Set the mode bits to 11 (neither periodic, nor one shot, nor tsc deadline)
- Set the TMICT to non-zero.
Then the lapic_timer.period will be 0, but the TMICT will not be. If the
guest then reads from the TMCCT then the host will perform a divide by 0.
This patch ensures that if the lapic_timer.period is 0, then the division
does not occur.
Reported-by: Andrew Honig <ahonig@google.com> Cc: stable@vger.kernel.org Signed-off-by: Andrew Honig <ahonig@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In multiple functions the vcpu_id is used as an offset into a bitfield. Ag
malicious user could specify a vcpu_id greater than 255 in order to set or
clear bits in kernel memory. This could be used to elevate priveges in the
kernel. This patch verifies that the vcpu_id provided is less than 255.
The api documentation already specifies that the vcpu_id must be less than
max_vcpus, but this is currently not checked.
Reported-by: Andrew Honig <ahonig@google.com> Cc: stable@vger.kernel.org Signed-off-by: Andrew Honig <ahonig@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Elie De Brauwer [Mon, 9 Dec 2013 18:48:28 +0000 (19:48 +0100)]
i2c: mux: Inherit retry count and timeout from parent for muxed bus
If a muxed i2c bus gets created the default retry count and
timeout of the muxed bus is zero. Hence it it possible that you
end up with a situation where the parent controller sets a default
retry count and timeout which gets applied and used while the muxed
bus (using the same controller) has a default retry count of zero
and a default timeout of 1s (set in i2c_add_adapter()). This can be
solved by initializing the retry count and timeout of the muxed
bus with the values used by the the parent at creation time.
Signed-off-by: Elie De Brauwer <eliedebrauwer@gmail.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Linus Torvalds [Thu, 12 Dec 2013 21:14:25 +0000 (13:14 -0800)]
Merge tag 'sound-3.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Still a slightly high amount of changes than wished, but they are all
good regression and/or device-specific fixes. Majority of commits are
for HD-audio, an HDMI ctl index fix that hits old graphics boards,
regression fixes for AD codecs and a few quirks.
Other than that, two major fixes are included: a 64bit ABI fix for
compress offload, and 64bit dma_addr_t truncation fix, which had hit
on PAE kernels"
* tag 'sound-3.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Add static DAC/pin mapping for AD1986A codec
ALSA: hda - One more Dell headset detection quirk
ALSA: hda - hdmi: Fix IEC958 ctl indexes for some simple HDMI devices
ALSA: hda - Mute all aamix inputs as default
ALSA: compress: Fix 64bit ABI incompatibility
ALSA: memalloc.h - fix wrong truncation of dma_addr_t
ALSA: hda - Another Dell headset detection quirk
ALSA: hda - A Dell headset detection quirk
ALSA: hda - Remove quirk for Dell Vostro 131
ALSA: usb-audio: fix uninitialized variable compile warning
ALSA: hda - fix mic issues on Acer Aspire E-572
Linus Torvalds [Thu, 12 Dec 2013 19:06:13 +0000 (11:06 -0800)]
Merge branch 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"A dvb core deadlock fix, a couple videobuf2 fixes an a series of media
driver fixes"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (30 commits)
[media] videobuf2-dma-sg: fix possible memory leak
[media] vb2: regression fix: always set length field.
[media] mt9p031: Include linux/of.h header
[media] rtl2830: add parent for I2C adapter
[media] media: marvell-ccic: use devm to release clk
[media] ths7303: Declare as static a private function
[media] em28xx-video: Swap release order to avoid lock nesting
[media] usbtv: Add support for PAL video source
[media] media_tree: Fix spelling errors
[media] videobuf2: Add support for file access mode flags for DMABUF exporting
[media] radio-shark2: Mark shark_resume_leds() inline to kill compiler warning
[media] radio-shark: Mark shark_resume_leds() inline to kill compiler warning
[media] af9035: unlock on error in af9035_i2c_master_xfer()
[media] af9033: fix broken I2C
[media] v4l: omap3isp: Don't check for missing get_fmt op on remote subdev
[media] af9035: fix broken I2C and USB I/O
[media] wm8775: fix broken audio routing
[media] marvell-ccic: drop resource free in driver remove
[media] tef6862/radio-tea5764: actually assign clamp result
[media] cx231xx: use after free on error path in probe
...
Linus Torvalds [Thu, 12 Dec 2013 19:05:19 +0000 (11:05 -0800)]
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fix from Guenter Roeck:
"Fix HIH-6130 driver to work with BeagleBone"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: HIH-6130: Support I2C bus drivers without I2C_FUNC_SMBUS_QUICK
Linus Torvalds [Thu, 12 Dec 2013 19:03:57 +0000 (11:03 -0800)]
Merge branch 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
Pull hwmon fixes from Jean Delvare.
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: Prevent some divide by zeros in FAN_TO_REG()
hwmon: (w83l768ng) Fix fan speed control range
hwmon: (w83l786ng) Fix fan speed control mode setting and reporting
hwmon: (lm90) Unregister hwmon device if interrupt setup fails
Will Deacon [Thu, 12 Dec 2013 17:40:22 +0000 (17:40 +0000)]
word-at-a-time: provide generic big-endian zero_bytemask implementation
Whilst architectures may be able to do better than this (which they can,
by simply defining their own macro), this is a generic stab at a
zero_bytemask implementation for the asm-generic, big-endian
word-at-a-time implementation.
On arm64, a clz instruction is used to implement the fls efficiently.
Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Will Deacon [Thu, 12 Dec 2013 17:40:21 +0000 (17:40 +0000)]
dcache: allow word-at-a-time name hashing with big-endian CPUs
When explicitly hashing the end of a string with the word-at-a-time
interface, we have to be careful which end of the word we pick up.
On big-endian CPUs, the upper-bits will contain the data we're after, so
ensure we generate our masks accordingly (and avoid hashing whatever
random junk may have been sitting after the string).
This patch adds a new dcache helper, bytemask_from_count, which creates
a mask appropriate for the CPU endianness.
Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 12 Dec 2013 18:20:58 +0000 (10:20 -0800)]
Merge tag 'iommu-fixes-for-v3.13-rc4' of git://github.com/awilliam/linux-vfio
Pull iommu fixes from Alex Williamson:
"arm/smmu driver updates via Will Deacon fixing locking around page
table walks and a couple other issues"
* tag 'iommu-fixes-for-v3.13-rc4' of git://github.com/awilliam/linux-vfio:
iommu/arm-smmu: fix error return code in arm_smmu_device_dt_probe()
iommu/arm-smmu: remove potential NULL dereference on mapping path
iommu/arm-smmu: use mutex instead of spinlock for locking page tables
Linus Torvalds [Thu, 12 Dec 2013 18:15:24 +0000 (10:15 -0800)]
Merge tag 'keys-devel-20131210' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull misc keyrings fixes from David Howells:
"These break down into five sets:
- A patch to error handling in the big_key type for huge payloads.
If the payload is larger than the "low limit" and the backing store
allocation fails, then big_key_instantiate() doesn't clear the
payload pointers in the key, assuming them to have been previously
cleared - but only one of them is.
Unfortunately, the garbage collector still calls big_key_destroy()
when sees one of the pointers with a weird value in it (and not
NULL) which it then tries to clean up.
- Three patches to fix the keyring type:
* A patch to fix the hash function to correctly divide keyrings off
from keys in the topology of the tree inside the associative
array. This is only a problem if searching through nested
keyrings - and only if the hash function incorrectly puts the a
keyring outside of the 0 branch of the root node.
* A patch to fix keyrings' use of the associative array. The
__key_link_begin() function initially passes a NULL key pointer
to assoc_array_insert() on the basis that it's holding a place in
the tree whilst it does more allocation and stuff.
This is only a problem when a node contains 16 keys that match at
that level and we want to add an also matching 17th. This should
easily be manufactured with a keyring full of keyrings (without
chucking any other sort of key into the mix) - except for (a)
above which makes it on average adding the 65th keyring.
* A patch to fix searching down through nested keyrings, where any
keyring in the set has more than 16 keyrings and none of the
first keyrings we look through has a match (before the tree
iteration needs to step to a more distal node).
- A patch to fix the big_key type's use of a shmem file as its
backing store causing audit messages and LSM check failures. This
is done by setting S_PRIVATE on the file to avoid LSM checks on the
file (access to the shmem file goes through the keyctl() interface
and so is gated by the LSM that way).
This isn't normally a problem if a key is used by the context that
generated it - and it's currently only used by libkrb5.
- A patch to fix the alignment of the system certificate data such
that it it works on s390. As I understand it, on the S390 arch,
symbols must be 2-byte aligned because loading the address discards
the least-significant bit"
* tag 'keys-devel-20131210' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
KEYS: correct alignment of system_certificate_list content in assembly file
Ignore generated file kernel/x509_certificate_list
security: shmem: implement kernel private shmem inodes
KEYS: Fix searching of nested keyrings
KEYS: Fix multiple key add into associative array
KEYS: Fix the keyring hash function
KEYS: Pre-clear struct key on allocation
Linus Torvalds [Thu, 12 Dec 2013 18:14:13 +0000 (10:14 -0800)]
Merge tag 'xfs-for-linus-v3.13-rc4' of git://oss.sgi.com/xfs/xfs
Pull xfs bugfixes from Ben Myers:
- fix for buffer overrun in agfl with growfs on v4 superblock
- return EINVAL if requested discard length is less than a block
- fix possible memory corruption in xfs_attrlist_by_handle()
* tag 'xfs-for-linus-v3.13-rc4' of git://oss.sgi.com/xfs/xfs:
xfs: growfs overruns AGFL buffer on V4 filesystems
xfs: don't perform discard if the given range length is less than block size
xfs: underflow bug in xfs_attrlist_by_handle()
Linus Torvalds [Thu, 12 Dec 2013 17:53:51 +0000 (09:53 -0800)]
futex: move user address verification up to common code
When debugging the read-only hugepage case, I was confused by the fact
that get_futex_key() did an access_ok() only for the non-shared futex
case, since the user address checking really isn't in any way specific
to the private key handling.
Now, it turns out that the shared key handling does effectively do the
equivalent checks inside get_user_pages_fast() (it doesn't actually
check the address range on x86, but does check the page protections for
being a user page). So it wasn't actually a bug, but the fact that we
treat the address differently for private and shared futexes threw me
for a loop.
Just move the check up, so that it gets done for both cases. Also, use
the 'rw' parameter for the type, even if it doesn't actually matter any
more (it's a historical artifact of the old racy i386 "page faults from
kernel space don't check write protections").
Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 12 Dec 2013 17:38:42 +0000 (09:38 -0800)]
futex: fix handling of read-only-mapped hugepages
The hugepage code had the exact same bug that regular pages had in
commit 7485d0d3758e ("futexes: Remove rw parameter from
get_futex_key()").
The regular page case was fixed by commit 9ea71503a8ed ("futex: Fix
regression with read only mappings"), but the transparent hugepage case
(added in a5b338f2b0b1: "thp: update futex compound knowledge") case
remained broken.
Found by Dave Jones and his trinity tool.
Reported-and-tested-by: Dave Jones <davej@fedoraproject.org> Cc: stable@kernel.org # v2.6.38+ Acked-by: Thomas Gleixner <tglx@linutronix.de> Cc: Mel Gorman <mgorman@suse.de> Cc: Darren Hart <dvhart@linux.intel.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Oleg Nesterov <oleg@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dan Carpenter [Thu, 10 Jan 2013 08:57:25 +0000 (03:57 -0500)]
Btrfs: fix access_ok() check in btrfs_ioctl_send()
The closing parenthesis is in the wrong place. We want to check
"sizeof(*arg->clone_sources) * arg->clone_sources_count" instead of
"sizeof(*arg->clone_sources * arg->clone_sources_count)".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Jie Liu <jeff.liu@oracle.com> Signed-off-by: Chris Mason <clm@fb.com>
cc: stable@vger.kernel.org
This is because reloc root inserted into @reloc_root_tree is not within one
transaction,reloc root may be cowed and root block bytenr will be reused then
oops happens.We should update reloc root in @reloc_root_tree when cow reloc
root node, fix it.
Signed-off-by: Wang Shilong <wangsl.fnst@cn.fujitsu.com> Reviewed-by: Miao Xie <miaox@cn.fujitsu.com> Signed-off-by: Chris Mason <clm@fb.com>
Btrfs: don't miss skinny extent items on delayed ref head contention
Currently extent-tree.c:btrfs_lookup_extent_info() can miss the lookup
of skinny extent items. This can happen when the execution flow is the
following:
* We do an extent tree lookup and fail to find a skinny extent item;
* As a result, we attempt to see if a non-skinny extent item exists,
either by looking at previous item in the leaf or by doing another
full extent tree search;
* We have a transaction and then we check for a matching delayed ref
head in the transaction's delayed refs rbtree;
* We find such delayed ref head and then we try to lock it with a
call to mutex_trylock();
* The lock was contended so we jump to the label "again", which repeats
the extent tree search but for a non-skinny extent item, because we set
previously metadata variable to 0 and the search key to look for a
non-skinny extent-item;
* After the jump (and after releasing the transaction's delayed refs
lock), a skinny extent item might have been added to the extent tree
but we will miss it because metadata is set to 0 and the search key
is set for a non-skinny extent-item.
The fix here is to not reset metadata to 0 and to jump to the initial search
key setup if the delayed ref head is contended, instead of jumping directly
to the extent tree search label ("again").
This issue was found while investigating the issue reported at Bugzilla 64961.
David Sterba suspected this function was missing extent items, and that
this could be caused by the last change to this function, which was made
in the following patch:
But in fact this issue already existed before, because after failing to find
a skinny extent item, the code set the search key for a non-skinny extent
item, and on contention of a matching delayed ref head it would not search
the extent tree for a skinny extent item anymore.
Signed-off-by: Filipe David Borba Manana <fdmanana@gmail.com> Reviewed-by: Liu Bo <bo.li.liu@oracle.com> Signed-off-by: Chris Mason <clm@fb.com>
It is because we cleared the default compression type when setting the
nodatacow. In fact, we needn't do it because we have used COMPRESS flag to
indicate if we need compressed the file data or not, needn't use the
variant -- compress_type -- in btrfs_info to do the same thing, and just
use it to hold the default compression type. Or we would get a wrong compress
type for a file whose own compress flag is set but the compress flag of its
filesystem is not set.
Reported-by: Tsutomu Itoh <t-itoh@jp.fujitsu.com> Signed-off-by: Miao Xie <miaox@cn.fujitsu.com> Reviewed-by: Liu Bo <bo.li.liu@oracle.com> Signed-off-by: Chris Mason <clm@fb.com>
Dan Carpenter [Thu, 12 Dec 2013 07:05:33 +0000 (08:05 +0100)]
hwmon: Prevent some divide by zeros in FAN_TO_REG()
The "rpm * div" operations can overflow here, so this patch adds an
upper limit to rpm to prevent that. Jean Delvare helped me with this
patch.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Roger Lucas <vt8231@hiddenengine.co.uk> Cc: stable@vger.kernel.org Signed-off-by: Jean Delvare <khali@linux-fr.org>
Jean Delvare [Thu, 12 Dec 2013 07:05:32 +0000 (08:05 +0100)]
hwmon: (w83l768ng) Fix fan speed control range
The W83L786NG stores the fan speed on 4 bits while the sysfs interface
uses a 0-255 range. Thus the driver should scale the user input down
to map it to the device range, and scale up the value read from the
device before presenting it to the user. The reserved register nibble
should be left unchanged.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: stable@vger.kernel.org Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Guenter Roeck [Thu, 12 Dec 2013 07:05:32 +0000 (08:05 +0100)]
hwmon: (lm90) Unregister hwmon device if interrupt setup fails
Commit 109b1283fb (hwmon: (lm90) Add support to handle IRQ) introduced
interrupt support. Its error handling code fails to unregister the already
registered hwmon device.
Fixes: 109b1283fb532ac773a076748ffccf76a7067cab Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Jean Delvare <khali@linux-fr.org>
Maxime Ripard [Tue, 10 Dec 2013 18:37:22 +0000 (19:37 +0100)]
ARM: sun6i: dt: Fix interrupt trigger types
The Allwinner A31 uses the ARM GIC as its internal interrupts controller. The
GIC can work on several interrupt triggers, and the A31 was actually setting it
up to use a rising edge as a trigger, while it was actually a level high
trigger, leading to some interrupts that would be completely ignored if the
edge was missed.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Cc: stable@vger.kernel.org # 3.12+ Signed-off-by: Olof Johansson <olof@lixom.net>
Maxime Ripard [Tue, 10 Dec 2013 18:37:21 +0000 (19:37 +0100)]
ARM: sun7i: dt: Fix interrupt trigger types
The Allwinner A20 uses the ARM GIC as its internal interrupts controller. The
GIC can work on several interrupt triggers, and the A20 was actually setting it
up to use a rising edge as a trigger, while it was actually a level high
trigger, leading to some interrupts that would be completely ignored if the
edge was missed.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Cc: stable@vger.kernel.org #3.12+ Signed-off-by: Olof Johansson <olof@lixom.net>
Shawn Guo [Tue, 10 Dec 2013 14:19:21 +0000 (22:19 +0800)]
MAINTAINERS: merge IMX6 entry into IMX
I have been co-maintaining IMX sub-architecture for a couple of years,
and collecting IMX sub-architecture patches rather than IMX6 only ones
for a few release cycles. It makes sense to officially add myself as
the co-maintainer for IMX sub-architecture now. Consequently, IMX6
entry can just be merged into IMX.
Stephen Warren [Fri, 6 Dec 2013 21:31:02 +0000 (14:31 -0700)]
ARM: tegra: add missing break to fuse initialization code
Add a missing break to the switch in tegra_init_fuse() which determines
which SoC the code is running on. This prevents the Tegra30+ fuse
handling code from running on Tegra20.
Fixes: 3bd1ae57f7bb ("ARM: tegra: add fuses as device randomness") Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Olof Johansson <olof@lixom.net>
Erratum 71 of PXA270M Processor Family Specification Update
(April 19, 2010) explains that watchdog reset time is just
8us insead of 10ms in EMTS.
If SDRAM is not reset, it causes memory bus congestion and
the device hangs. We put SDRAM in selfresh mode before watchdog
reset, removing potential freezes.
Without this patch PXA270-based ICP DAS LP-8x4x hangs after up to 40
reboots. With this patch it has successfully rebooted 500 times.
Signed-off-by: Sergei Ianovich <ynvich@gmail.com> Tested-by: Marek Vasut <marex@denx.de> Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Olof Johansson <olof@lixom.net>
When converting from tosa-keyboard driver to matrix keyboard, tosa keys
received extra 1 column shift. Replace that with correct values to make
keyboard work again.
Fixes: f69a6548c9d5 ('[ARM] pxa/tosa: make use of the matrix keypad driver') Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com> Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Olof Johansson <olof@lixom.net>
hwmon: HIH-6130: Support I2C bus drivers without I2C_FUNC_SMBUS_QUICK
Some I2C bus drivers do not allow zero-length data transfers which are
required to start a measurement with the HIH6130/1 sensor. Nevertheless,
we can overcome this limitation by writing a zero dummy byte. This byte
is ignored by the sensor and was verified to be working with the OMAP
I2C bus driver in a BeagleBone board.
Signed-off-by: José Miguel Gonçalves <jose.goncalves@inov.pt>
[Guenter Roeck: Simplified complexity of write_length initialization] Cc: stable@vger.kernel.org # v3.10+ Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Takashi Iwai [Tue, 10 Dec 2013 16:29:26 +0000 (17:29 +0100)]
ALSA: hda - Add static DAC/pin mapping for AD1986A codec
AD1986A codec is a pretty old codec and has really many hidden
restrictions. One of such is that each DAC is dedicated to certain
pin although there are possible connections. Currently, the generic
parser tries to assign individual DACs as much as possible, and this
lead to two bad situations: connections where the sound actually
doesn't work, and connections conflicting other channels.
We may fix this by trying to find the best connections more harder,
but as of now, it's easier to give some hints for paired DAC/pin
connections and honor them if available, since such a hint is needed
only for specific codecs (right now only AD1986A, and there will be
unlikely any others in future).
Hui Wang [Wed, 11 Dec 2013 03:41:31 +0000 (11:41 +0800)]
ALSA: hda - One more Dell headset detection quirk
On the Dell machines with codec whose Subsystem Id is 0x10280624,
no external microphone can be detected when plugging a 3-ring
headset. If we add "model=dell-headset-multi" for the
snd-hda-intel.ko, the problem will disappear.
BugLink: https://bugs.launchpad.net/bugs/1259790 Cc: David Henningsson <david.henningsson@canonical.com> Cc: stable@vger.kernel.org Signed-off-by: Hui Wang <hui.wang@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Anssi Hannula [Tue, 10 Dec 2013 20:46:34 +0000 (22:46 +0200)]
ALSA: hda - hdmi: Fix IEC958 ctl indexes for some simple HDMI devices
In case a single HDA card has both HDMI and S/PDIF outputs, the S/PDIF
outputs will have their IEC958 controls created starting from index 16
and the HDMI controls will be created starting from index 0.
However, HDMI simple_playback_build_controls() as used by old VIA and
NVIDIA codecs incorrectly requests the IEC958 controls to be created
with an S/PDIF type instead of HDMI.
In case the card has other codecs that have HDMI outputs, the controls
will be created with wrong index=16, causing them to e.g. be unreachable
by the ALSA "hdmi" alias.
Fix that by making simple_playback_build_controls() request controls
with HDMI indexes.
Not many cards have an affected configuration, but e.g. ASUS M3N78-VM
contains an integrated NVIDIA HDA "card" with:
- a VIA codec that has, among others, an S/PDIF pin incorrectly
labelled as an HDMI pin, and
- an NVIDIA MCP7x HDMI codec.
Reported-by: MysterX on #openelec Tested-by: MysterX on #openelec Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi> Cc: <stable@vger.kernel.org> # 3.8+ Signed-off-by: Takashi Iwai <tiwai@suse.de>
Jeff Layton [Mon, 2 Dec 2013 20:26:19 +0000 (15:26 -0500)]
nfsd: when reusing an existing repcache entry, unhash it first
The DRC code will attempt to reuse an existing, expired cache entry in
preference to allocating a new one. It'll then search the cache, and if
it gets a hit it'll then free the cache entry that it was going to
reuse.
The cache code doesn't unhash the entry that it's going to reuse
however, so it's possible for it end up designating an entry for reuse
and then subsequently freeing the same entry after it finds it. This
leads it to a later use-after-free situation and usually some list
corruption warnings or an oops.
Fix this by simply unhashing the entry that we intend to reuse. That
will mean that it's not findable via a search and should prevent this
situation from occurring.
Cc: stable@vger.kernel.org # v3.10+ Reported-by: Christoph Hellwig <hch@infradead.org> Reported-by: g. artim <gartim@gmail.com> Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Takashi Iwai [Tue, 10 Dec 2013 16:33:49 +0000 (17:33 +0100)]
ALSA: hda - Mute all aamix inputs as default
Not all channels have been initialized, so far, especially when aamix
NID itself doesn't have amps but its leaves have. This patch fixes
these holes. Otherwise you might get unexpected loopback inputs,
e.g. from surround channels.
Linus Torvalds [Tue, 10 Dec 2013 19:30:10 +0000 (11:30 -0800)]
Merge git://www.linux-watchdog.org/linux-watchdog
Pull watchdog fixes from Wim Van Sebroeck:
"Drop the unnecessary miscdevice.h includes that we forgot in commit 487722cf2d66 ("watchdog: Get rid of MODULE_ALIAS_MISCDEV statements")
and fix an oops for the sc1200_wdt driver"
* git://www.linux-watchdog.org/linux-watchdog:
sc1200_wdt: Fix oops
watchdog: Drop unnecessary include of miscdevice.h
Linus Torvalds [Tue, 10 Dec 2013 19:02:33 +0000 (11:02 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"One patch to increase the number of possible CPUs to 256, with the
latest machine a single LPAR can have up to 101 CPUs. Plus a number
of bug fixes, the clock_gettime patch fixes a regression added in the
3.13 merge window"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/time,vdso: fix clock_gettime for CLOCK_MONOTONIC
s390/vdso: ectg gettime support for CLOCK_THREAD_CPUTIME_ID
s390/vdso: fix access-list entry initialization
s390: increase CONFIG_NR_CPUS limit
s390/smp,sclp: fix size of sclp_cpu_info structure
s390/sclp: replace uninitialized early_event_mask_sccb variable with sccb_early
s390/dasd: fix memory leak caused by dangling references to request_queue
KEYS: correct alignment of system_certificate_list content in assembly file
Apart from data-type specific alignment constraints, there are also
architecture-specific alignment requirements.
For example, on s390 symbols must be on even addresses implying a 2-byte
alignment. If the system_certificate_list_end symbol is on an odd address
and if this address is loaded, the least-significant bit is ignored. As a
result, the load_system_certificate_list() fails to load the certificates
because of a wrong certificate length calculation.
To be safe, align system_certificate_list on an 8-byte boundary. Also improve
the length calculation of the system_certificate_list content. Introduce a
system_certificate_list_size (8-byte aligned because of unsigned long) variable
that stores the length. Let the linker calculate this size by introducing
a start and end label for the certificate content.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com> Signed-off-by: David Howells <dhowells@redhat.com>
$ git status
# On branch pending-rebases
# Untracked files:
# (use "git add <file>..." to include in what will be committed)
#
# kernel/x509_certificate_list
nothing added to commit but untracked files present (use "git add" to track)
$
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: David Howells <dhowells@redhat.com>
Nishanth Menon [Wed, 4 Dec 2013 01:39:13 +0000 (19:39 -0600)]
ARM: OMAP2+: omap_device: add fail hook for runtime_pm when bad data is detected
Due to the cross dependencies between hwmod for automanaged device
information for OMAP and dts node definitions, we can run into scenarios
where the dts node is defined, however it's hwmod entry is yet to be
added. In these cases:
a) omap_device does not register a pm_domain (since it cannot find
hwmod entry).
b) driver does not know about (a), does a pm_runtime_get_sync which
never fails
c) It then tries to do some operation on the device (such as read the
revision register (as part of probe) without clock or adequate OMAP
generic PM operation performed for enabling the module.
This causes a crash such as that reported in:
https://bugzilla.kernel.org/show_bug.cgi?id=66441
When 'ti,hwmod' is provided in dt node, it is expected that the device
will not function without the OMAP's power automanagement. Hence, when
we hit a fail condition (due to hwmod entries not present or other
similar scenario), fail at pm_domain level due to lack of data, provide
enough information for it to be fixed, however, it allows for the driver
to take appropriate measures to prevent crash.
Reported-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de> Signed-off-by: Nishanth Menon <nm@ti.com> Acked-by: Kevin Hilman <khilman@linaro.org> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Kevin Hilman <khilman@linaro.org>
For V4 filesystems, we don't have a agfl header structure, and so
XFS_AGFL_SIZE() returns an entire sector's worth of entries, which
we then index from an offset into the sector. Hence: buffer overrun.
This problem was introduced in 3.10 by commit 77c95bba ("xfs: add
CRC checks to the AGFL") which changed the AGFL structure but failed
to update the growfs code to handle the different structures.
Fix it by using the correct offset into the buffer for both V4 and
V5 filesystems.
Cc: <stable@vger.kernel.org> Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Jie Liu <jeff.liu@oracle.com> Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit b7d961b35b3ab69609aeea93f870269cb6e7ba4d)
Jie Liu [Wed, 20 Nov 2013 08:08:53 +0000 (16:08 +0800)]
xfs: don't perform discard if the given range length is less than block size
For discard operation, we should return EINVAL if the given range length
is less than a block size, otherwise it will go through the file system
to discard data blocks as the end range might be evaluated to -1, e.g,
# fstrim -v -o 0 -l 100 /xfs7
/xfs7: 9811378176 bytes were trimmed
This issue can be triggered via xfstests/generic/288.
Also, it seems to get the request queue pointer via bdev_get_queue()
instead of the hard code pointer dereference is not a bad thing.
Signed-off-by: Jie Liu <jeff.liu@oracle.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit f9fd0135610084abef6867d984e9951c3099950d)
Kevin Hilman [Tue, 10 Dec 2013 15:44:32 +0000 (07:44 -0800)]
Merge tag 'for-v3.13-rc/hwmod-fixes-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes
From Paul Walmsley:
ARM: OMAP2+: hwmod code/data: fixes for v3.13-rc
Fix a few hwmod code problems involving recovery with bad data and bad
IP block OCP reset handling. Also, fix the hwmod data to enable IP
block OCP reset for the OMAP USBHOST devices on OMAP3+.
Basic build, boot, and PM tests are available here:
* tag 'for-v3.13-rc/hwmod-fixes-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending:
ARM: OMAP2+: hwmod: Fix usage of invalid iclk / oclk when clock node is not present
ARM: OMAP3: hwmod data: Don't prevent RESET of USB Host module
ARM: OMAP2+: hwmod: Fix SOFTRESET logic
ARM: OMAP4+: hwmod data: Don't prevent RESET of USB Host module
projects / ~andy / linux / log