Lad, Prabhakar [Tue, 15 Jan 2013 08:04:41 +0000 (05:04 -0300)]
[media] ARM: davinci: da850 evm: pass platform data for adv7343 encoder
Without this patch the adv7343 encoder was being set to default
configuration which caused display not to work on this board.
This patch passes the necessary platform data required for adv7343
encoder to work on da850 evm.
Lad, Prabhakar [Tue, 22 Jan 2013 04:19:50 +0000 (01:19 -0300)]
[media] media: adv7343: accept configuration through platform data
The current code was implemented with some default configurations,
this default configuration works on board and doesn't work on other.
This patch accepts the configuration through platform data and configures
the encoder depending on the data passed.
Hans Verkuil [Tue, 11 Sep 2012 10:35:30 +0000 (07:35 -0300)]
[media] tm6000: fix querycap and input/tuner compliance issues
- add device_caps support
- fix bus_info
- fix numerous tuner-related problems due to incorrect tests
and setting v4l2_tuner fields to wrong values.
- remove (audio) input support from the radio: it doesn't belong
there. This also fixed a nasty issue where opening the radio
would set dev->input to 5 for no good reason. This was never
set back to a valid TV input after closing the radio device,
thus leaving it at 5 which is out of bounds of the vinput
card array.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Tue, 29 Jan 2013 10:21:02 +0000 (07:21 -0300)]
[media] meye: convert to the control framework
Convert the meye driver to the control framework. Some private controls
have been replaced with standardized controls (SHARPNESS and JPEGQUAL).
The AGC control looks like it can be replaced by the AUTOGAIN control, but
it isn't a boolean so I do not know how to interpret it.
The FRAMERATE control looks like it can be replaced by S_PARM, but again,
without knowing how to interpret it I decided to leave it alone.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Wed, 30 Jan 2013 16:29:02 +0000 (13:29 -0300)]
[media] videobuf2: don't return POLLERR when only polling for events
If you only poll for events, then vb2_poll will return POLLPRI | POLLERR if
no streaming is in progress. That's not right, it's perfectly valid to
poll just for events.
Cc: Pawel Osciak <pawel@osciak.com> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Thu, 24 Jan 2013 07:42:05 +0000 (04:42 -0300)]
[media] Move DV-class control IDs from videodev2.h to v4l2-controls.h
When the control IDs were split off from videodev2.h to v4l2-controls.h
these new Digital Video controls were forgotten (the two patches may
have crossed one another).
Move these controls to their proper place in v4l2-controls.h.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[media] s5p-fimc: Redefine platform data structure for fimc-is
Newer Exynos4 SoC are equipped with a local camera ISP that
controls external raw image sensor directly. Such sensors
can be connected through FIMC-LITEn (and MIPI-CSISn) IPs to
the ISP, which then feeds image data to the FIMCn IP. Thus
there can be two busses associated with an image source
(sensor). Rename struct s5p_fimc_isp_info describing external
image sensor (video decoder) to struct fimc_source_info to
avoid confusion. bus_type is split into fimc_bus_type and
sensor_bus_type. The bus type enumeration is extended to
include both FIMC Writeback input types.
The bus_type enumeration and the data structure name in the
board files are modified according to the above changes.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Kukjin Kim <kgene.kim@samsung.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The V4L2_SEL_TGT_CROP_BOUNDS, V4L2_SEL_TGT_COMPOSE_BOUNDS selection
targets are not supposed to be handled in the set_selection ioctl.
Remove the code that doesn't do anything sensible now and make sure
ctx->state is modified with the spinlock held.
[media] s5p-fimc: Avoid null pointer dereference in fimc_capture_ctrls_create()
With presence of some faults, e.g. caused by wrong platform data or
the device tree structure the IDX_SENSOR entry in the array may be NULL,
so make sure it is not dereferenced then.
Sachin Kamat [Tue, 29 Jan 2013 05:32:30 +0000 (02:32 -0300)]
[media] s5c73m3: Staticize some symbols
Fixes the following sparse warnings:
drivers/media/i2c/s5c73m3/s5c73m3-core.c:42:5: warning:
symbol 'boot_from_rom' was not declared. Should it be static?
drivers/media/i2c/s5c73m3/s5c73m3-core.c:45:5: warning:
symbol 'update_fw' was not declared. Should it be static?
drivers/media/i2c/s5c73m3/s5c73m3-core.c:298:5: warning:
symbol 's5c73m3_isp_comm_result' was not declared. Should it be static?
[media] s5p-csis: Check return value of clk_enable/clk_set_rate
clk_set_rate(), clk_enable() functions can fail, so check the return
values to avoid surprises. While at it use ERR_PTR() value to indicate
an invalid clock.
[media] s5p-fimc: Check return value of clk_enable/clk_set_rate
clk_set_rate(), clk_enable() functions can fail, so check the return
values to avoid surprises. While at it use ERR_PTR() value to indicate
an invalid clock.
The previous method of registering platform entities into the main
driver using driver_find() and then iterating over devices bound to
a driver was racy and is being removed here. Nothing was preventing
module from unloading during a call to try_module_get(driver->owner).
Instead, we look up a device first and then check for its driver while
holding device lock.
The platform sub-devices are looked up and registered to the top
level driver. When any sub-device is not yet initialized and ready
the main driver's probe() will be deferred.
[media] s5p-fimc: fimc-lite: Prevent deadlock at STREAMON/OFF ioctls
This patch fixes regression introduced in commit 6319d6a002beb26631
'[media] fimc-lite: Add ISP FIFO output support'.
In case of a configuration where video is captured at the video node
exposed by the FIMC-LITE driver there is a following video pipeline:
sensor -> MIPI-CSIS.n -> FIMC-LITE.n subdev -> FIMC-LITE.n video node
In this situation s_stream() handler of the FIMC-LITE.n is called
back from within VIDIOC_STREAMON/OFF ioctl of the FIMC-LITE.n video
node, through vb2_stream_on/off(), start/stop_streaming and
fimc_pipeline_call(set_stream). The fimc->lock mutex is already held
then, before invoking vidioc_streamon/off. So it must not be taken
again in the s_stream() callback in this case, to avoid a deadlock.
This patch makes fimc->out_path atomic_t so the mutex don't need
to be taken in the FIMC-LITE subdev s_stream() callback in the DMA
output case.
The .s_power FIMC-LITE subdev callback is now empty and
unneeded. The FIMC-LITE IP power handling will be done
by the FIMC-IS driver, so just remove the callback.
Andrzej Hajda [Thu, 22 Nov 2012 14:39:18 +0000 (11:39 -0300)]
[media] V4L: Add S5C73M3 camera driver
Add driver for S5C73M3 image sensor. The driver exposes the sensor as
two subdevs: pure sensor and output interface. Two subdev architecture
supports interleaved UYVY/JPEG image format with separate frame size
for both sub-formats, there is a spearate pad for each sub-format.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Sachin Kamat [Thu, 17 Jan 2013 03:07:18 +0000 (00:07 -0300)]
[media] s5p-g2d: Add support for G2D H/W Rev.4.1
Modified the G2D driver (which initially supported only H/W Rev.3)
to support H/W Rev.4.1 present on Exynos4x12 and Exynos52x0 SOCs.
- Set the SRC and DST type to 'memory' instead of using reset values.
- FIMG2D v4.1 H/W uses different logic for stretching(scaling).
- Use CACHECTL_REG only with FIMG2D v3.
[s.nawrocki: removed empty line at end of file]]
[media] s5p-fimc: Fix bytesperline value for V4L2_PIX_FMT_YUV420M format
Make sure bytesperline for Cb, Cr planes for V4L2_PIX_FMT_YUV420M
format is half of the Y plane value, rather than having same
bytesperline for all planes.
While at it, simplify the bytesperline parameter handling by
storing it when image format is set and returning those values
when getting the format, instead of recalculating bytesperline
from intermediate parameters.
Reported-by: Sebastian Dröge <sebastian.droege@collabora.co.uk> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Fri, 28 Sep 2012 11:18:07 +0000 (08:18 -0300)]
[media] tuner-core: map audmode to STEREO for radio devices
Fixes a v4l2-compliance error: setting audmode to a value other than mono
or stereo for a radio device should map to MODE_STEREO.
The spec specifies that for radio devices only mono and stereo audmodes are
valid. If the user specifies another audmode in v4l2_tuner, then that should
be mapped to valid audmode. That didn't happen here.
Note that tuner drivers might decide to limit the possible audmode even
further if it only supports mono. In that case the tuner driver can set
audmode to mono. However, that new value wasn't copied back to t->audmode,
and that has been fixed as well in this patch.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[media] V4L: Add driver for OV9650/52 image sensors
This patch adds V4L2 sub-device driver for OV9650/OV9652 image sensors.
The driver exposes following V4L2 controls:
- auto/manual exposure,
- auto/manual white balance,
- auto/manual gain,
- brightness, saturation, sharpness,
- horizontal/vertical flip,
- color bar test pattern,
- banding filter (power line frequency).
Frame rate can be configured with g/s_frame_interval pad level ops.
Supported resolution are only: SXGA, VGA, QVGA.
[media] V4L: Add v4l2_ctrl_subdev_log_status() helper function
This patch adds a v4l2 core helper function that can be used as
the log_status handler for subdevs that only need to log state
of the v4l2 controls owned by the subdev's control handler.
[media] V4L: Add v4l2_ctrl_subdev_subscribe_event() helper function
Add a v4l2 core helper function that can be used as the subdev
.subscribe_event handler. This allows to eliminate some boilerplate
from drivers that are only handling the control events.
[media] V4L: Add v4l2_event_subdev_unsubscribe() helper function
Add a v4l2 core helper function that can be used as the subdev
.unsubscribe_event handler. This allows to eliminate some
boilerplate from drivers that are only handling the control events.
[media] v4l2-ctrl: Add helper function for the controls range update
This patch adds a helper function that allows to modify range,
i.e. minimum, maximum, step and default value of a v4l2 control,
after the control has been created and initialized. This is helpful
in situations when range of a control depends on user configurable
parameters, e.g. camera sensor absolute exposure time depending on
an output image resolution and frame rate.
v4l2_ctrl_modify_range() function allows to modify range of an
INTEGER, BOOL, MENU, INTEGER_MENU and BITMASK type controls.
Based on a patch from Hans Verkuil http://patchwork.linuxtv.org/patch/8654.
This patch fixes a bug which causes all histogram regions to start in the
top left corner of the image. The histogram region coordinates are 16 bit
values which share a 32 bit register. The bug is due to the region end
value assignments overwriting the region start values with zero.
The preview engine includes filters that consume columns and lines as
part of their operation, thus resulting in a cropped image. To allow
turning those filters on/off during streaming without affecting the
output image size, the driver adds additional cropping to make the total
number of cropped columns and lines constant regardless of which filters
are enabled.
This process needlessly includes the CFA filter, as whether the filter
is enabled only depends on the sink pad format, which can't change
during streaming.
Exclude the CFA filter from the preview engine margins.
Oliver Neukum [Thu, 10 Jan 2013 10:04:55 +0000 (07:04 -0300)]
[media] uvcvideo: Fix race of open and suspend in error case
Ming Lei reported:
IMO, there is a minor fault in the error handling path of
uvc_status_start() inside uvc_v4l2_open(), and the 'users' count should
have been decreased before usb_autopm_put_interface(). In theory, a [URB
resubmission] warning can be triggered when the device is opened just
between usb_autopm_put_interface() and atomic_dec(&stream->dev->users).
The fix is trivial.
Reported-by: Ming Lei <tom.leiming@gmail.com> Signed-off-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/platform/davinci/dm355_ccdc.c:593:9: warning: ‘val1’ may be
used uninitialized in this function [-Wuninitialized]
drivers/media/platform/davinci/dm355_ccdc.c:560:6: note: ‘val1’ was declared here
This is a false positive but the compiler has no way to know about it,
so initialize the variable to 0.
Paul Bolle [Tue, 5 Feb 2013 12:42:21 +0000 (09:42 -0300)]
[media] saa7164: silence GCC warnings
Compiling the saa7164 driver without CONFIG_VIDEO_ADV_DEBUG set triggers
these GCC warnings:
drivers/media/pci/saa7164/saa7164-encoder.c:1301:12: warning: ‘saa7164_g_register’ defined but not used [-Wunused-function]
drivers/media/pci/saa7164/saa7164-encoder.c:1314:12: warning: ‘saa7164_s_register’ defined but not used [-Wunused-function]
Silence these warnings by wrapping these two functions in an "#ifdef
CONFIG_VIDEO_ADV_DEBUG" and "#endif" pair.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[media] imon: fix Knob event interpretation issues on ARM
Events for the iMon Knob pad where not correctly interpreted on ARM,
resulting in buggy mouse movements (cursor going straight out of the
screen), key pad only generating KEY_RIGHT and KEY_DOWN events.
A reproducer is:
int main(int argc, char ** argv)
{
char rel_x = 0x00; printf("rel_x:%d @%s:%d\n", rel_x, __FILE__, __LINE__);
rel_x = 0x0f; printf("rel_x:%d @%s:%d\n", rel_x, __FILE__, __LINE__);
rel_x |= ~0x0f; printf("rel_x:%d @%s:%d\n", rel_x, __FILE__, __LINE__);
return 0;
}
(running on x86 or amd64)
$ ./test
rel_x:0 @test.c:6
rel_x:15 @test.c:7
rel_x:-1 @test.c:8
(running on armv6)
rel_x:0 @test.c:6
rel_x:15 @test.c:7
rel_x:255 @test.c:8
Forcing the rel_x and rel_y variables as signed char fixes the issue.
Merge branch 'v4l_for_linus' into staging/for_v3.9
* v4l_for_linus: (464 commits)
[media] uvcvideo: Set error_idx properly for S_EXT_CTRLS failures
[media] uvcvideo: Cleanup leftovers of partial revert
[media] uvcvideo: Return -EACCES when trying to set a read-only control
Linux 3.8-rc3
mm: reinstante dropped pmd_trans_splitting() check
cred: Remove tgcred pointer from struct cred
drm/ttm: fix fence locking in ttm_buffer_object_transfer
ARM: clps711x: Fix bad merge of clockevents setup
ARM: highbank: save and restore L2 cache and GIC on suspend
ARM: highbank: add a power request clear
ARM: highbank: fix secondary boot and hotplug
ARM: highbank: fix typos with hignbank in power request functions
ARM: dts: fix highbank cpu mpidr values
ARM: dts: add device_type prop to cpu nodes on Calxeda platforms
drm/prime: drop reference on imported dma-buf come from gem
xen/netfront: improve truesize tracking
ARM: mx5: Fix MX53 flexcan2 clock
ARM: OMAP2+: am33xx-hwmod: Fix wrongly terminated am33xx_usbss_mpu_irqs array
sctp: fix Kconfig bug in default cookie hmac selection
EDAC: Cleanup device deregistering path
...
Andreas Regel [Sun, 11 Mar 2012 17:11:45 +0000 (14:11 -0300)]
[media] stv090x: On STV0903 do not set registers of the second path
Sometimes there is a problem when trying to access the non-existing registers
of the second demodulator path on the STV0903.
This change removes the calls in case the driver is used on a STV0903.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de> Acked-by: Manu Abraham <manu@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The logic that resets the device is wrong. It should be resetting
just the layer that got read. Also, stop is needed before updating
the counters.
While there, rename it, as we'll soon introduce a postBER logic
there.
[media] dvb_frontend: print a msg if a property doesn't exist
If userspace calls a property that doesn't exist, it currently
just returns -EINVAL. However, this is more likely a problem at
the userspace application, calling it with a non-existing property.
So, add a debug message to help tracking it.
Add Signal/Noise ratio measurement. On this device, a global measure
is taken by the demod. It also provides per-layer CNR measurements,
based on Modulation Error measures (MER).
Reviewed-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the methods to read bit error/bit count measurements from
mb86a20s. On ISDB-T devices, those reads are done per layer.
However, as userspace applications may not be aware of that,
add a global measure that will sum the bit errors and bit
counts for each layer, storing them into a global value.
Reviewed-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[media] mb86a20s: calculate statistics at .read_status()
Instead of providing separate callbacks to read the several FE
stats properties, the better seems to use just one method that will:
- Read lock status;
- Read signal strength;
- if locked, get TMCC data;
- if locked, get DVB statistics.
As the DVB frontend thread will call this read_status callback
on every 3 seconds, and userspace can even call it earlier,
all stats data and layers layout will be updated together if
available, with is a good thing.
Reviewed-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[media] dvb: the core logic to handle the DVBv5 QoS properties
Add the logic to poll, reset counters and report the QoS stats
to the end user.
The idea is that the core will periodically poll the frontend for
the stats. The frontend may return -EBUSY, if the previous collect
didn't finish, or it may fill the cached data.
The value returned to the end user is always the cached data.
Reviewed-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
projects / ~andy / linux / log