Padmavathi Venna [Thu, 21 Jul 2011 07:57:59 +0000 (16:57 +0900)]
ARM: S5P64X0: External Interrupt Support
Add external interrupt support for S5P64X0.The external interrupt
group 0(0 to 15) is used for wake-up source in stop and sleep mode.
Add generic irq chip support
Signed-off-by: Padmavathi Venna <padma.v@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Marek Szyprowski [Thu, 21 Jul 2011 07:43:25 +0000 (16:43 +0900)]
ARM: EXYNOS4: Enable MFC on Samsung NURI
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Jonghun Han [Thu, 21 Jul 2011 06:46:26 +0000 (15:46 +0900)]
ARM: EXYNOS4: Add platform device and helper functions for FIMD
This patch adds platform device s5p_device_fimd0 for EXYNOS4 FIMD0.
EXYNOS4 has two FIMDs(FIMD0, FIMD1). FIMD1 will be added later.
Some definitions used to enable EXYNOS4 FIMD0 are added.
Signed-off-by: Jonghun Han <jonghun.han@samsung.com> Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Jingoo Han [Thu, 21 Jul 2011 06:42:38 +0000 (15:42 +0900)]
ARM: EXYNOS4: Change devname for FIMD clkdev
According to SoC name, EXYNOS4, this patch changes devname
for FIMD from 's5pv310-fb' to 'exynos4-fb'.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
[kgene.kim@samsung.com: removed to change wrong clock name] Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Sangbeom Kim [Thu, 21 Jul 2011 05:15:11 +0000 (14:15 +0900)]
ARM: SAMSUNG: Add IRQ_I2S0 definition
To handle i2s0 interrupt and To fix compilation error
adds IRQ_I2S0 for exynos4, s3c64xx, s5p64x0
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
[kgene.kim@samsung.com: Fixed build failure due to inclusion] Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Sangbeom Kim [Thu, 21 Jul 2011 05:12:19 +0000 (14:12 +0900)]
ARM: SAMSUNG: Add platform device for idma
Exynos4 and S5PC110(S5PV210) has Internal dma(idma) in AUDSS.
To support idma, register idma platform device.
and Exynos4 and S5PC110 has different IDMA address.
TO handle different IDMA address, register idma platform data
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
MyungJoo Ham [Thu, 21 Jul 2011 02:25:23 +0000 (11:25 +0900)]
ARM: EXYNOS4: Add more registers to be saved and restored for PM
We need more registers to be saved and restored for PM of EXYNOS4210.
Otherwise, with additional drivers running, suspend-to-RAM fails to
wake up properly. This patch adds registers omitted in the initial PM
patches.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
MyungJoo Ham [Thu, 21 Jul 2011 02:21:56 +0000 (11:21 +0900)]
ARM: EXYNOS4: Add more register addresses of CMU
These registers are crucial for PM to work properly.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Thomas Abraham [Tue, 14 Jun 2011 10:12:27 +0000 (19:12 +0900)]
ARM: EXYNOS4: Add clkdev support
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
[kgene.kim@samsung.com: removed changes of mach-exynos4/time.c] Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
MyungJoo Ham [Wed, 20 Jul 2011 15:31:27 +0000 (00:31 +0900)]
ARM: EXYNOS4: configure rtc-s3c on NURI
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
MyungJoo Ham [Wed, 20 Jul 2011 15:31:27 +0000 (00:31 +0900)]
ARM: EXYNOS4: configure MAX8903 secondary charger on NURI
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
MyungJoo Ham [Wed, 20 Jul 2011 15:31:27 +0000 (00:31 +0900)]
ARM: EXYNOS4: configure ADC on NURI
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
MyungJoo Ham [Wed, 20 Jul 2011 15:31:27 +0000 (00:31 +0900)]
ARM: EXYNOS4: configure MAX17042 fuel gauge on NURI
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
MyungJoo Ham [Wed, 20 Jul 2011 15:31:27 +0000 (00:31 +0900)]
ARM: EXYNOS4: configure regulators and PMIC(MAX8997) on NURI
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: Fix build - inclusion of max8997-private.h] Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
MyungJoo Ham [Wed, 20 Jul 2011 15:31:26 +0000 (00:31 +0900)]
ARM: EXYNOS4: Increase NR_IRQS for devices with more IRQs
MAX8997/17042, which are used by Exynos4-NURI, use additional IRQ
numbers after GPIO's IRQs. The patch creates some room for those
devices.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
MyungJoo Ham [Wed, 20 Jul 2011 12:08:18 +0000 (21:08 +0900)]
ARM: S5PV210: Support ADC
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
MyungJoo Ham [Wed, 20 Jul 2011 12:08:18 +0000 (21:08 +0900)]
ARM: EXYNOS4: Support ADC
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
MyungJoo Ham [Wed, 20 Jul 2011 12:08:18 +0000 (21:08 +0900)]
ARM: SAMSUNG: Revise PM for 12-bit ADC operations
- Fixed: 12bit precision is lost at suspend/resume
- Updated: use pm_dev_ops
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
MyungJoo Ham [Wed, 20 Jul 2011 12:08:18 +0000 (21:08 +0900)]
ARM: SAMSUNG: ADC Channel selection
In S5PV210/S5PC110/EXYNOS4, ADCMUX channel selection uses ADCMUX
register, not ADCCON register. This patch corrects the behavior of
SAMSUNG-ADC for such CPUs.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
MyungJoo Ham [Wed, 20 Jul 2011 12:08:17 +0000 (21:08 +0900)]
ARM: SAMSUNG: use regulator VDD for ADC
This patch allows the Samsung ADC driver to enable VDD regulator
at probe and resume and to disable at exit and suspend.
In a platform where ADC's VDD regulator is not "always-on", this
control is required although this patch does not provide fine-grained
power control (turning on the regulator only when being accessed).
However, if VDD regulator ("vdd" for the adc device) is not provided,
the regulator control will not be activated because there are platforms
that do not provide regulator for ADC device.
arch_initcall has been modified to module_init in order to allow
regulators to be available at probe.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Jaecheol Lee [Mon, 18 Jul 2011 10:21:41 +0000 (19:21 +0900)]
ARM: EXYNOS4: Move S5P_CENTRAL_SEQ_CONFIGURATION setting for PM
We need to balance between set and check S5P_CENTRAL_SEQ_CONFIGURATION
register in syscore_ops suspend/resume function when failure in enter
suspend mode. Moved this register setting for PM for the purpose of balancing.
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Jaecheol Lee [Mon, 18 Jul 2011 10:21:34 +0000 (19:21 +0900)]
ARM: EXYNOS4: Support early wakeup entering sleep mode
Since early wakeup can be handled in pm so we don't need masking
interrupts of external GIC. When the early wakeup interrupt happens,
PMU(Power Management Unit) ignores WFI instruction. This means that
PC(Program Counter) passed without any changes. This patch can handle
that case by early wakeup interrupt.
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
[kgene.kim@samsung.com: fixed return of exynos4_cpu_suspend()] Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Jaecheol Lee [Mon, 18 Jul 2011 10:21:23 +0000 (19:21 +0900)]
ARM: EXYNOS4: Support system level power down configuration
EXYNOS4 supports 3 different system level power down mode by PMU (Power
Management Unit). Each power down mode need to configure many PMU registers
with different value. This patch supports function to configure PMU registers
with pre-defined values in PMU code. This function may be used by PM code and
AFTR/LPA support driver.
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
JungHi Min [Sat, 16 Jul 2011 04:39:09 +0000 (13:39 +0900)]
ARM: EXYNOS4: Add support Core1 Power On/Off with hotplug in/out
To insert the code for power on/off with pmu control to support hotplug in/out core1
As for hotplug.c, the codes for core1 to be hotplug in/out is inserted.
As for regs-pmu.h, S5P_CORE_LOCAL_PWR_EN is defined.
As for platsmp.c, the codes for core1 to be powered on is inserted.
Signed-off-by: JungHi Min <junghi.min@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
ARM: EXYNOS4: Add chained enrty/exit function to uart interrupt handler
This patch adds chained IRQ enter/exit functions to uart
interrupt handler in order to function correctly on primary
controllers with different methods of flow control.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
ARM: GIC: move gic_chip_data structure declaration to header
Since Samsung EXYNOS4210 cannot support register banking in GIC,
so needs to update CPU interface base address.
The 'gic_chip_data' is used for it, this patch moves gic_chip_data
structure declaraton to arch/arm/include/asm/hardware/gic.h to use
it.
Cc: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Changhwan Youn <chaos.youn@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
ARM: EXYNOS4: set the affinity of mct1 interrupt using IRQ_MCT_L1
IRQ_MCT_L1 is connected directly to GIC in external GIC mapping,
while in internal GIC mapping, it is connected to GIC through
interrupt combiner. Therfore the affinity for mct1 event timer
interrupt should be changed through IRQ_MCT_L1.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Marek Szyprowski [Wed, 22 Jun 2011 04:43:39 +0000 (13:43 +0900)]
ARM: EXYNOS4: Add qt602240 touch screen device on Universal_C210
This patch adds definitions to enable support for qt602240 touch screen
driver for Universal C210 board.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Marek Szyprowski [Wed, 22 Jun 2011 04:43:39 +0000 (13:43 +0900)]
ARM: EXYNOS4: Add MCS Touchkey device on Universal_C210
This patch adds definitions to enable support for MCS Touchkey driver
for Universal C210 board.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Marek Szyprowski [Wed, 22 Jun 2011 04:43:39 +0000 (13:43 +0900)]
ARM: EXYNOS4: Add FIMC device on Universal_C210
This patch adds definitions to enable support for s5p-fimc driver for
Universal C210 board.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Marek Szyprowski [Mon, 13 Jun 2011 06:47:17 +0000 (15:47 +0900)]
ARM: EXYNOS4: Fix compilation break
The patch "ARM: SAMSUNG: Add support for pre-sleep/post-restore gpio
control" broke compilation on Exynos4 platform with power management
enabled. This patch adds missing stubs that fixes this issue.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Ben Dooks [Wed, 1 Jun 2011 09:44:50 +0000 (10:44 +0100)]
ARM: SAMSUNG: Add support for pre-sleep/post-restore gpio control
Add a callback so that per-arch can do pre-sleep and post-resume
gpio configuration so that for the S3C64XX, the GPIO configuration
is restored before the sleep mode is cleared.
For the S3C64XX case, it means that the GPIOs get set back to normal
operation after the restore code puts the original configurations
back in after the
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Ben Dooks [Wed, 1 Jun 2011 09:44:51 +0000 (10:44 +0100)]
ARM: S3C64XX: Ensure VIC based IRQs can be resumed from
Any interrupts based off either of the onboard VICs cannot be resumed
from any more as it seems set_irq_wake() is now checking the error code
returned from the low level handlers and not setting the wake-state on
the interrupt if this fails.
Ensure that we make the interrupts we can resume from available on the
VIC and then do a pre-sleep mask of all the VIC interrupts as the wakeup
is handled by a seperate block.
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Thomas Abraham [Tue, 14 Jun 2011 10:12:26 +0000 (19:12 +0900)]
ARM: SAMSUNG: Add clkdev infrastructure
The struct clk definition for Samsung platforms is extended to include
a instance of struct clk_lookup and a device name. When clocks are
registered using s3c24xx_register_clock function, the dev_id, con_id
and clk members are initialized with information from the struct clk
instance and struct clk_lookup member is registered.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Thomas Abraham [Tue, 14 Jun 2011 10:12:26 +0000 (19:12 +0900)]
serial: Remove redundant console_initcall from s3c and s5p console drivers
Uart port is registered as a console during the driver's probe.
So explict registration of console with console_initcall is
removed.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
[kgene.kim@samsung.com: removed changes of s3c2400 and s3c24a0] Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Merge branches 'cns3xxx/devel', 'davinci/devel', 'imx/devel', 'lpc32xx/devel', 'pxa/devel', 'tegra/devel' and 'stericsson/master' of git+ssh://master.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc into next/devel
Colin Cross [Sun, 10 Jul 2011 21:59:45 +0000 (14:59 -0700)]
ARM: tegra: remove copy-and-pasted usb platform data from boards
trimslice and paz00 both have functionally identical platform
data for the tegra-ehci driver. Move the platform data into
devices.c, and remove it from all the board files.
Signed-off-by: Colin Cross <ccross@android.com> Tested-by: Konstantin Sinyuk <kostyas@compulab.co.il> Acked-by: Olof Johansson <olof@lixom.net>
Colin Cross [Sun, 10 Jul 2011 21:37:22 +0000 (14:37 -0700)]
ARM: tegra: remove copy-and-pasted i2c platform data in boards
Every board file includes the same platform data definition
for the i2c-tegra driver's bus speed. Move the platform data
into devices.c, and remove it from all the board files.
Signed-off-by: Colin Cross <ccross@android.com> Tested-by: Konstantin Sinyuk <kostyas@compulab.co.il> Acked-by: Olof Johansson <olof@lixom.net>
KOSAKI Motohiro [Thu, 23 Jun 2011 08:28:28 +0000 (17:28 +0900)]
arm,tegra: replace cpu_set() with modern api
cpu_set() is marked as obsolete cpumask function and we plan to
remove it in future.
This patch replace it with modern cpumask function.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: Colin Cross <ccross@android.com> Cc: Erik Gilling <konkers@android.com> Cc: Olof Johansson <olof@lixom.net> Cc: Russell King <linux@arm.linux.org.uk> Cc: linux-tegra@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org Signed-off-by: Colin Cross <ccross@android.com>
Robert Morell [Wed, 8 Jun 2011 01:53:23 +0000 (18:53 -0700)]
arm: tegra: remove generic disp clock divisor flag
Although disp1 and disp2 have 7.1 divisors, their corresponding
registers in the clk_rst block are not the interface to program the
divisors. Setting the generic DIV_U71 flag may cause the code to
attempt to program the clock at a different divisor, which will confuse
any code attempting to use that clock since it isn't actually being
divided.
Signed-off-by: Robert Morell <rmorell@nvidia.com> Signed-off-by: Colin Cross <ccross@android.com>
Marc Dietrich [Thu, 19 May 2011 12:08:29 +0000 (14:08 +0200)]
ARM: tegra: paz00: change the machine name
This renames "paz00" in MACHINE_START macro to a neater string.
PAZ00 seems to have been the Compal internal project name, while
PROCYON looks like Toshiba project name.
Anyway, the AC100 support package in Ubuntu needs the new naming to
identify the machine.
Signed-off-by: Marc Dietrich <marvin24@gmx.de> Signed-off-by: Colin Cross <ccross@android.com>
Marc Dietrich [Thu, 19 May 2011 12:08:27 +0000 (14:08 +0200)]
ARM: tegra: paz00: enable usb ports
This patch add support for the second and third ehci bus on paz00.
The first bus needs gadget and nvec support and will be added once
the needed patches are upstream.
Signed-off-by: Marc Dietrich <marvin24@gmx.de> Signed-off-by: Colin Cross <ccross@android.com>
Marc Dietrich [Thu, 19 May 2011 12:08:26 +0000 (14:08 +0200)]
ARM: tegra: paz00: register i2c busses
This adds support for the i2c busses on paz00. The 3rd bus is
reserved for the nvec, which acts as master and i2c-tegra has
not yet support for this kind of operation.
The sound codec (alc5632) is connected to the first bus and will
be added once the codec and glue driver is upstream.
The thermal sensor (atd7461) is connected to dvc as usual, but will
not be added now because i2c-tegra still misses probe support
(needs I2C_FUNC_SMBUS_EMUL).
Signed-off-by: Marc Dietrich <marvin24@gmx.de> Signed-off-by: Colin Cross <ccross@android.com>
Colin Cross [Sun, 10 Jul 2011 20:54:02 +0000 (13:54 -0700)]
ARM: tegra: remove mach/barriers.h
The barriers implemented in arch/arm/mach-tegra/mach/barriers.h
are exactly the same as the default barriers implemented in
arch/arm/include/asm/system.h. Remove barriers.h from Tegra,
and don't select ARCH_HAS_BARRIERS.
Signed-off-by: Colin Cross <ccross@android.com> Acked-by: Olof Johansson <olof@lixom.net>
* U-Boot statically assigns MMC device IDs based on controller ID.
* U-Boot assumes that kernel MMC device ID numbering matches U-Boot numbering.
* U-Boot provides a kernel cmdline option e.g. root=/dev/mmcblk0p3 based on
that numbering.
* The kernel dynamically assigns MMC device IDs based on enumeration order of
the memory behind the host controller, rather than statically based on host
controller ID like U-Boot.
* By registering the SDHCI controller for the built-in eMMC first, the
enumeration of the built-in eMMC is performed first, and hence eMMC gets
assigned ID 0 just like U-Boot. If the SD slot is filled, it then gets
assigned ID 1 just like U-Boot.
* If the MMC IDs mismatch, and the system boots from SD card not eMMC, the
kernel will access the eMMC instead of SD card when attempting to mount
/dev/mmcblk1p3 as the root fs. If eMMC is not partitioned/formatted, the
kernel will panic since the root fs can't be mounted. If eMMC is partitioned
and formatted, the kernel will mount an unexpected filesystem as the root fs.
This change relies on the SDHCI driver performing initial card detection
synchronously during device registration. This is currently the case.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Colin Cross <ccross@android.com>
ARM: introduce handle_IRQ() not to dump exception stack
On Mon, Jul 11, 2011 at 3:52 PM, Russell King - ARM Linux
<linux@arm.linux.org.uk> wrote:
...
> The __exception annotation on a function causes this to happen:
>
> [<c002406c>] (asm_do_IRQ+0x6c/0x8c) from [<c0024b84>]
> (__irq_svc+0x44/0xcc)
> Exception stack(0xc3897c78 to 0xc3897cc0)
> 7c60: 4022d3204022e000
> 7c80: 0800007500001000c32273c0c03ce1c0c2b49b784022d000c2b420b400000001
> 7ca0: 00000000c3897cfc00000000c3897cc0c00afc54c002edd800000013ffffffff
>
> Where that stack dump represents the pt_regs for the exception which
> happened. Any function found in while unwinding will cause this to
> be printed.
>
> If you insert a C function between the IRQ assembly and asm_do_IRQ,
> the
> dump you get from asm_do_IRQ will be the stack for your function,
> not
> the pt_regs. That makes the feature useless.
>
When __irq_svc - or any of the other exception handling assembly code -
calls the C code, the stack pointer will be pointing at the pt_regs
structure.
All the entry points into C code from the exception handling code are
marked with __exception or __exception_irq_enter to indicate that they
are one of the functions which has pt_regs above them.
Normally, when you've entered asm_do_IRQ() you will have this stack
layout (higher address towards top):
pt_regs
asm_do_IRQ frame
If you insert a C function between the exception assembly code and
asm_do_IRQ, you end up with this stack layout instead:
pt_regs
your function frame
asm_do_IRQ frame
This means when we unwind, we'll get to asm_do_IRQ, and rather than
dumping out the pt_regs, we'll dump out your functions stack frame
instead, because that's what is above the asm_do_IRQ stack frame
rather than the expected pt_regs structure.
The fix is to introduce handle_IRQ() for no exception stack dump, so
it can be called with MULTI_IRQ_HANDLER is selected and a C function
is between the assembly code and the actual IRQ handling code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Documentation/Changes: remove some really obsolete text
That file harkens back to the days of the big 2.4 -> 2.6 version jump,
and was based even then on older versions. Some of it is just obsolete,
and Jesper Juhl points out that it talks about kernel versions 2.6 and
should be updated to 3.0.
Remove some obsolete text, and re-phrase some other to not be 2.6-specific.
Merge branch 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
[media] msp3400: fill in v4l2_tuner based on vt->type field
[media] tuner-core.c: don't change type field in g_tuner or g_frequency
[media] cx18/ivtv: fix g_tuner support
[media] tuner-core: power up tuner when called with s_power(1)
[media] v4l2-ioctl.c: check for valid tuner type in S_HW_FREQ_SEEK
[media] tuner-core: simplify the standard fixup
[media] tuner-core/v4l2-subdev: document that the type field has to be filled in
[media] v4l2-subdev.h: remove unused s_mode tuner op
[media] feature-removal-schedule: change in how radio device nodes are handled
[media] bttv: fix s_tuner for radio
[media] pvrusb2: fix g/s_tuner support
[media] v4l2-ioctl.c: prefill tuner type for g_frequency and g/s_tuner
[media] tuner-core: fix tuner_resume: use t->mode instead of t->type
[media] tuner-core: fix s_std and s_tuner
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
cifs: drop spinlock before calling cifs_put_tlink
cifs: fix expand_dfs_referral
cifs: move bdi_setup_and_register outside of CONFIG_CIFS_DFS_UPCALL
cifs: factor smb_vol allocation out of cifs_setup_volume_info
cifs: have cifs_cleanup_volume_info not take a double pointer
cifs: fix build_unc_path_to_root to account for a prefixpath
cifs: remove bogus call to cifs_cleanup_volume_info
Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86:
hp-wmi: fix use after free
dell-laptop - using buffer without mutex_lock
Revert: "dell-laptop: Toggle the unsupported hardware killswitch"
platform-drivers-x86: set backlight type to BACKLIGHT_PLATFORM
thinkpad-acpi: handle HKEY 0x4010, 0x4011 events
drivers/platform/x86: Fix memory leak
thinkpad-acpi: handle some new HKEY 0x60xx events
acer-wmi: fix bitwise bug when set device state
acer-wmi: Only update rfkill status for associated hotkey events
projects / ~andy / linux / log