Keith Packard [Sun, 3 Oct 2010 07:33:06 +0000 (00:33 -0700)]
drm/i915: Use pipe state to tell when pipe is off
Instead of waiting for the display line value to settle, we can simply
wait for the pipe configuration register 'state' bit to turn off.
Contrarywise, disabling the plane will not cause the display line
value to stop changing, so instead we wait for the vblank interrupt
bit to get set. And, we only do this when we're not about to wait for
the pipe to turn off.
Signed-off-by: Keith Packard <keithp@keithp.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Keith Packard [Sun, 3 Oct 2010 07:33:05 +0000 (00:33 -0700)]
drm/i915: vblank status not valid while training display port
While the display port is in training mode, vblank interrupts don't
occur. Because we have to wait for the display port output to turn on
before starting the training sequence, enable the output in 'normal'
mode so that we can tell when a vblank has occurred, then start the
training sequence.
Signed-off-by: Keith Packard <keithp@keithp.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Sinan Akman [Sun, 3 Oct 2010 03:28:29 +0000 (21:28 -0600)]
of/spi: Fix OF-style driver binding of spi devices
This patch adds the OF hook to the spi core so that devices
can automatically be registered based on device tree data. This fixes
a problem with spi devices not binding to drivers after the cleanup of
the spi & i2c binding code.
Signed-off-by: Sinan Akman <sinan@writeme.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Roel Kluin [Sat, 2 Oct 2010 12:03:32 +0000 (14:03 +0200)]
spi: spi-gpio.c tests SPI_MASTER_NO_RX bit twice, but not SPI_MASTER_NO_TX
The SPI_MASTER_NO_TX bit (can't do buffer write) wasn't tested. This
code was introduced in commit 3c8e1a84 (spi/spi-gpio: add support for
controllers without MISO or MOSI pin). This patch fixes a bug in
choosing which transfer ops to use.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Axel Lin [Fri, 1 Oct 2010 05:56:27 +0000 (13:56 +0800)]
regulator: max8649 - fix setting extclk_freq
The SYNC bits are BIT6 and BIT7 of MAX8649_SYNC register.
pdata->extclk_freq could be [0|1|2].
(MAX8649_EXTCLK_26MHZ|MAX8649_EXTCLK_13MHZ|MAX8649_EXTCLK_19MHZ)
It requires to left shift 6 bits to properly set extclk_freq.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
cifs: prevent infinite recursion in cifs_reconnect_tcon
cifs: set backing_dev_info on new S_ISREG inodes
David Howells [Fri, 1 Oct 2010 09:31:03 +0000 (10:31 +0100)]
MN10300: Fix flush_icache_range()
flush_icache_range() is given virtual addresses to describe the region. It
deals with these by attempting to translate them through the current set of
page tables.
This is fine for userspace memory and vmalloc()'d areas as they are governed by
page tables. However, since the regions above 0x80000000 aren't translated
through the page tables by the MMU, the kernel doesn't bother to set up page
tables for them (see paging_init()).
This means flush_icache_range() as it stands cannot be used to flush regions of
the VM area between 0x80000000 and 0x9fffffff where the kernel resides if the
data cache is operating in WriteBack mode.
To fix this, make flush_icache_range() first check for addresses in the upper
half of VM space and deal with them appropriately, before dealing with any
range in the page table mapped area.
Ordinarily, this is not a problem, but it has the capacity to make kprobes and
kgdb malfunction. It should not affect gdbstub, signal frame setup or module
loading as gdb has its own flush functions, and the others take place in the
page table mapped area only.
Linus Torvalds [Fri, 1 Oct 2010 17:58:31 +0000 (10:58 -0700)]
Merge branch 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
vmwgfx: Fix fb VRAM pinning failure due to fragmentation
vmwgfx: Remove initialisation of dev::devname
vmwgfx: Enable use of the vblank system
vmwgfx: vt-switch (master drop) fixes
drm/vmwgfx: Fix breakage introduced by commit "drm: block userspace under allocating buffer and having drivers overwrite it (v2)"
drm: Hold the mutex when dropping the last GEM reference (v2)
drm/gem: handlecount isn't really a kref so don't make it one.
drm: i810/i830: fix locked ioctl variant
drm/radeon/kms: add quirk for MSI K9A2GM motherboard
drm/radeon/kms: fix potential segfault in r600_ioctl_wait_idle
drm: Prune GEM vma entries
drm/radeon/kms: fix up encoder info messages for DFP6
drm/radeon: fix PCI ID 5657 to be an RV410
Linus Torvalds [Fri, 1 Oct 2010 17:55:54 +0000 (10:55 -0700)]
Merge branch 'for-linus/i2c/2636-rc5' of git://git.fluff.org/bjdooks/linux
* 'for-linus/i2c/2636-rc5' of git://git.fluff.org/bjdooks/linux:
i2c-s3c2410: fix calculation of SDA line delay
i2c-davinci: Fix race when setting up for TX
i2c-octeon: Return -ETIMEDOUT in octeon_i2c_wait() on timeout
Linus Torvalds [Fri, 1 Oct 2010 17:53:06 +0000 (10:53 -0700)]
Merge branch 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
omap: McBSP: tx_irq_completion used in rx_irq_handler
omap: Fix compile dependency to LEDS_CLASS
Prevent from recursively locking the reiserfs lock in reiserfs_unpack()
because we may call journal_begin() that requires the lock to be taken
only once, otherwise it won't be able to release the lock while taking
other mutexes, ending up in inverted dependencies between the journal
mutex and the reiserfs lock for example.
This fixes:
=======================================================
[ INFO: possible circular locking dependency detected ]
2.6.35.4.4a #3
-------------------------------------------------------
lilo/1620 is trying to acquire lock:
(&journal->j_mutex){+.+...}, at: [<d0325bff>] do_journal_begin_r+0x7f/0x340 [reiserfs]
but task is already holding lock:
(&REISERFS_SB(s)->lock){+.+.+.}, at: [<d032a278>] reiserfs_write_lock+0x28/0x40 [reiserfs]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
reiserfs: fix dependency inversion between inode and reiserfs mutexes
The reiserfs mutex already depends on the inode mutex, so we can't lock
the inode mutex in reiserfs_unpack() without using the safe locking API,
because reiserfs_unpack() is always called with the reiserfs mutex locked.
This fixes:
=======================================================
[ INFO: possible circular locking dependency detected ]
2.6.35c #13
-------------------------------------------------------
lilo/1606 is trying to acquire lock:
(&sb->s_type->i_mutex_key#8){+.+.+.}, at: [<d0329450>] reiserfs_unpack+0x60/0x110 [reiserfs]
but task is already holding lock:
(&REISERFS_SB(s)->lock){+.+.+.}, at: [<d032a268>] reiserfs_write_lock+0x28/0x40 [reiserfs]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
Kukjin Kim [Thu, 30 Sep 2010 22:15:35 +0000 (15:15 -0700)]
MAINTAINERS: update maintainer for S5P ARM ARCHITECTURES
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com> Acked-by: Ben Dooks <ben-linux@fluff.org> Acked-by: Russell King <rmk@arm.linux.org.uk> Cc: Kyungmin Park <kmpark@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Petr Vandrovec [Thu, 30 Sep 2010 22:15:34 +0000 (15:15 -0700)]
MAINTAINERS: update matroxfb & ncpfs status
I moved couple years ago, so let's update my email and snail mail.
And I do not have any access to Matrox hardware anymore, and I'm quite
unresponsive to matroxfb bug reports (sorry Alan), so saying that I'm
maintainer is a bit far fetched.
For ncpfs I do not use ncpfs in my daily life either, but at least I can
test that one, so I can stay listed here for odd fixes.
Signed-off-by: Petr Vandrovec <petr@vandrovec.name> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Don Mullis [Thu, 30 Sep 2010 22:15:32 +0000 (15:15 -0700)]
lib/list_sort: do not pass bad pointers to cmp callback
If the original list is a POT in length, the first callback from line 73
will pass a==b both pointing to the original list_head. This is dangerous
because the 'list_sort()' user can use 'container_of()' and accesses the
"containing" object, which does not necessary exist for the list head. So
the user can access RAM which does not belong to him. If this is a write
access, we can end up with memory corruption.
Dan Rosenberg [Thu, 30 Sep 2010 22:15:31 +0000 (15:15 -0700)]
sys_semctl: fix kernel stack leakage
The semctl syscall has several code paths that lead to the leakage of
uninitialized kernel stack memory (namely the IPC_INFO, SEM_INFO,
IPC_STAT, and SEM_STAT commands) during the use of the older, obsolete
version of the semid_ds struct.
The copy_semid_to_user() function declares a semid_ds struct on the stack
and copies it back to the user without initializing or zeroing the
"sem_base", "sem_pending", "sem_pending_last", and "undo" pointers,
allowing the leakage of 16 bytes of kernel stack memory.
The code is still reachable on 32-bit systems - when calling semctl()
newer glibc's automatically OR the IPC command with the IPC_64 flag, but
invoking the syscall directly allows users to use the older versions of
the struct.
Signed-off-by: Dan Rosenberg <dan.j.rosenberg@gmail.com> Cc: Manfred Spraul <manfred@colorfullife.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton [Thu, 30 Sep 2010 22:15:29 +0000 (15:15 -0700)]
drivers/serial/mrst_max3110.c needs linux/irq.h
sparc64 allmodconfig:
drivers/serial/mrst_max3110.c: In function `serial_m3110_startup':
drivers/serial/mrst_max3110.c:470: error: `IRQ_TYPE_EDGE_FALLING' undeclared (first use in this function)
Andrew Morton [Thu, 30 Sep 2010 22:15:29 +0000 (15:15 -0700)]
arch/m68k/mac/macboing.c: use unsigned long for irqflags
Fix the warnings
arch/m68k/mac/macboing.c: In function 'mac_mksound':
arch/m68k/mac/macboing.c:189: warning: comparison of distinct pointer types lacks a cast
arch/m68k/mac/macboing.c:211: warning: comparison of distinct pointer types lacks a cast
arch/m68k/mac/macboing.c: In function 'mac_quadra_start_bell':
arch/m68k/mac/macboing.c:241: warning: comparison of distinct pointer types lacks a cast
arch/m68k/mac/macboing.c:263: warning: comparison of distinct pointer types lacks a cast
arch/m68k/mac/macboing.c: In function 'mac_quadra_ring_bell':
arch/m68k/mac/macboing.c:283: warning: comparison of distinct pointer types lacks a cast
Andrew Morton [Thu, 30 Sep 2010 22:15:28 +0000 (15:15 -0700)]
drivers/serial/mfd.c needs slab.h
alpha allmodconfig:
drivers/serial/mfd.c:144: error: implicit declaration of function 'kzalloc'
drivers/serial/mfd.c:144: warning: assignment makes pointer from integer without a cast
Ira W. Snyder [Thu, 30 Sep 2010 22:15:27 +0000 (15:15 -0700)]
kfifo: fix scatterlist usage
The kfifo_dma family of functions use sg_mark_end() on the last element in
their scatterlist. This forces use of a fresh scatterlist for each DMA
operation, which makes recycling a single scatterlist impossible.
Change the behavior of the kfifo_dma functions to match the usage of the
dma_map_sg function. This means that users must respect the returned
nents value. The sample code is updated to reflect the change.
This bug is trivial to cause: call kfifo_dma_in_prepare() such that it
prepares a scatterlist with a single entry comprising the whole fifo.
This is the case when you map the entirety of a newly created empty fifo.
This causes the setup_sgl() function to mark the first scatterlist entry
as the end of the chain, no matter what comes after it.
Afterwards, add and remove some data from the fifo such that another call
to kfifo_dma_in_prepare() will create two scatterlist entries. It returns
nents=2. However, due to the previous sg_mark_end() call, sg_is_last()
will now return true for the first scatterlist element. This causes the
sample code to print a single scatterlist element when it should print
two.
By removing the call to sg_mark_end(), we make the API as similar as
possible to the DMA mapping API. All users are required to respect the
returned nents.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu> Cc: Stefani Seibold <stefani@seibold.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jeff Layton [Wed, 29 Sep 2010 19:27:08 +0000 (15:27 -0400)]
cifs: prevent infinite recursion in cifs_reconnect_tcon
cifs_reconnect_tcon is called from smb_init. After a successful
reconnect, cifs_reconnect_tcon will call reset_cifs_unix_caps. That
function will, in turn call CIFSSMBQFSUnixInfo and CIFSSMBSetFSUnixInfo.
Those functions also call smb_init.
It's possible for the session and tcon reconnect to succeed, and then
for another cifs_reconnect to occur before CIFSSMBQFSUnixInfo or
CIFSSMBSetFSUnixInfo to be called. That'll cause those functions to call
smb_init and cifs_reconnect_tcon again, ad infinitum...
Break the infinite recursion by having those functions use a new
smb_init variant that doesn't attempt to perform a reconnect.
Reported-and-Tested-by: Michal Suchanek <hramrach@centrum.cz> Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com>
vmwgfx: Fix fb VRAM pinning failure due to fragmentation
If the soon-to-be scanout buffer is partly covering the intended
VRAM region, move and pin will fail. In that case, just move it out
to system before attempting to move it in again.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
This is to avoid accessing uninitialized data during
drm_irq_uninstall and vblank ioctls. At the same time, enable error check from
drm_kms_init which previously appeared to ignore all errors.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
We add an option not to enable fbdev, this option is off (0) by default.
Not enabling fbdev at load time makes it possible to co-operate with
vga16fb and vga text mode when VT switching.
However, if 3D resources are active when VT switching, we're currently
not able to switch over to vga, due to device limitations.
This fixes a bug where we previously lost 3D state during VT switch.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Chris Wilson [Thu, 30 Sep 2010 08:10:26 +0000 (09:10 +0100)]
drm: Hold the mutex when dropping the last GEM reference (v2)
In order to be fully threadsafe we need to check that the drm_gem_object
refcount is still 0 after acquiring the mutex in order to call the free
function. Otherwise, we may encounter scenarios like:
Note that no driver is currently using the free_unlocked vfunc and it is
scheduled for removal, hasten that process.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=30454 Reported-and-Tested-by: Magnus Kessler <Magnus.Kessler@gmx.net> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: stable@kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
Suresh Siddha [Fri, 1 Oct 2010 01:19:07 +0000 (21:19 -0400)]
intel_idle: Voluntary leave_mm before entering deeper
Avoid TLB flush IPIs for the cores in deeper c-states by voluntary leave_mm()
before entering into that state. CPUs tend to flush TLB in those c-states
anyways.
acpi_idle does this with C3-type states, but it was not caried over
when intel_idle was introduced. intel_idle can apply it
to C-states in addition to those that ACPI might export as C3...
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
Eric Dumazet [Thu, 30 Sep 2010 02:16:44 +0000 (02:16 +0000)]
vlan: dont drop packets from unknown vlans in promiscuous mode
Roger Luethi noticed packets for unknown VLANs getting silently dropped
even in promiscuous mode.
Check for promiscuous mode in __vlan_hwaccel_rx() and vlan_gro_common()
before drops.
As suggested by Patrick, mark such packets to have skb->pkt_type set to
PACKET_OTHERHOST to make sure they are dropped by IP stack.
Reported-by: Roger Luethi <rl@hellgate.ch> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> CC: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Dave Airlie [Mon, 27 Sep 2010 06:17:17 +0000 (16:17 +1000)]
drm/gem: handlecount isn't really a kref so don't make it one.
There were lots of places being inconsistent since handle count
looked like a kref but it really wasn't.
Fix this my just making handle count an atomic on the object,
and have it increase the normal object kref.
Now i915/radeon/nouveau drivers can drop the normal reference on
userspace object creation, and have the handle hold it.
This patch fixes a memory leak or corruption on unload, because
the driver had no way of knowing if a handle had been actually
added for this object, and the fbcon object needed to know this
to clean itself up properly.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Dave Airlie <airlied@redhat.com>
MyungJoo Ham [Thu, 30 Sep 2010 13:54:46 +0000 (15:54 +0200)]
i2c-s3c2410: fix calculation of SDA line delay
S3C2440 style I2C controller uses PCLK to calculate the SDA line delay.
The driver wrongly assumed that this delay is calculated from the
frequency that the controller is operating on. This patch fixes this
issue.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Thomas Gleixner [Tue, 28 Sep 2010 18:57:19 +0000 (20:57 +0200)]
x86, irq: Plug memory leak in sparse irq
free_irq_cfg() is not freeing the cpumask_vars in irq_cfg. Fixing this
triggers a use after free caused by the fact that copying struct
irq_cfg is done with memcpy, which copies the pointer not the cpumask.
Fix both places.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Yinghai Lu <yhlu.kernel@gmail.com>
LKML-Reference: <alpine.LFD.2.00.1009282052570.2416@localhost6.localdomain6> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@kernel.org Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Commit c52c2ddc1dfa ("alpha: switch osf_sigprocmask() to use of
sigprocmask()") had several problems. The more obvious compile issues
got fixed in commit 0f44fbd297e1 ("alpha: fix compile problem in
arch/alpha/kernel/signal.c"), but it also caused a regression.
Since _BLOCKABLE is already the set of signals that can be blocked, the
code should do "newmask & _BLOCKABLE" rather than inverting _BLOCKABLE
before masking.
Reported-by: Michael Cree <mcree@orcon.net.nz> Patch-by: Al Viro <viro@zeniv.linux.org.uk> Patch-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Grant Likely [Thu, 30 Sep 2010 12:14:23 +0000 (14:14 +0200)]
of/i2c: Fix module load order issue caused by of_i2c.c
Commit 959e85f7, "i2c: add OF-style registration and binding" caused a
module dependency loop where of_i2c.c calls functions in i2c-core, and
i2c-core calls of_i2c_register_devices() in of_i2c. This means that
when i2c support is built as a module when CONFIG_OF is set, then
neither i2c_core nor of_i2c are able to be loaded.
This patch fixes the problem by moving the of_i2c_register_devices()
calls back into the device drivers. Device drivers already
specifically request the core code to parse the device tree for
devices anyway by setting the of_node pointer, so it isn't a big
deal to also call the registration function. The drivers just become
slightly more verbose.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Jean Delvare <khali@linux-fr.org>
i2c: Fix checks which cause legacy suspend to never get called
For devices which are not adapted to runtime PM a call to
pm_runtime_suspended always returns true.
Hence the pm_runtime_suspended checks below prevent legacy
suspend from getting called.
So do a pm_runtime_suspended check only for devices with a
dev_pm_ops populated (which hence do not rely on the legacy
suspend.)
Signed-off-by: Rajendra Nayak <rnayak@ti.com> Acked-by: Rafael J. Wysocki <rjw@sisk.pl> Cc: Ben Dooks <ben-linux@fluff.org> Cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
ret is still -1, if during the polling read_byte() returns at once
with I2C_PCA_CON_SI set. So ret > 0 would lead *_waitforcompletion()
to return 0, in spite of the proper behavior.
The routine was rewritten, so that ret has always a proper value,
before returning.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com> Reviewed-by: Wolfram Sang <w.sang@pengutronix.de> Cc: stable@kernel.org Signed-off-by: Jean Delvare <khali@linux-fr.org>
In current i2c core driver, call to pm_runtime_set_active from
i2c_device_pm_resume will unconditionally enable i2c module and
increment child count of the parent. Because of this, in CPU Idle
path, i2c does not idle, preventing Core to enter retention. Also i2c
module will not be suspended upon system suspend as
pm_runtime_set_suspended is not called from i2c_device_pm_suspend.
This issue is fixed by removing pm_runtime_set_active call from resume
path which is not necessary.
This fix has been tested on OMAP4430.
Signed-off-by: Partha Basak <p-basak2@ti.com> Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com> Acked-by: Rafael J. Wysocki <rjw@sisk.pl> Cc: Kevin Hilman <khilman@deeprootsystems.com> Cc: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Jean Delvare <khali@linux-fr.org>
Wolfram Sang [Thu, 30 Sep 2010 12:14:22 +0000 (14:14 +0200)]
i2c: Remove obsolete cleanup for clientdata
A few new i2c-drivers came into the kernel which clear the clientdata-pointer
on exit. This is obsolete meanwhile, so fix it and hope the word will spread.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
In case of error during probe() the driver calls free_irq() function
on not yet allocated irq. This patches fixes the call sequence in case of
the error.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L/DVB: v4l: videobuf: prevent passing a NULL to dma_free_coherent()
When a driver that uses videobuf-dma-contig is used with the USERPTR
memory access method a kernel oops might happen: a NULL address may be
passed to dma_free_coherent(). This happens when an application calls
REQBUFS and then exits without queuing any buffers. This patch fixes
that bug.
Brian Rogers [Wed, 22 Sep 2010 11:06:43 +0000 (08:06 -0300)]
V4L/DVB: ir-core: Fix null dereferences in the protocols sysfs interface
For some cards, ir_dev->props and ir_dev->raw are both NULL. These cards are
using built-in IR decoding instead of raw, and can't easily be made to switch
protocols.
So upon reading /sys/class/rc/rc?/protocols on such a card, return 'builtin' as
the supported and enabled protocol. Return -EINVAL on any attempts to change
the protocol. And most important of all, don't crash.
Signed-off-by: Brian Rogers <brian@xyzw.org> Acked-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The i810 and i830 device drivers may replace their file operations
on an open file descriptor. My previous patch to move the BKL
out of the common DRM code into these drivers only caught the
default file operations, not the ones that actually end up being
used.
Found while trying to come up with a way to kill the BKL for
good in these drivers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Dave Airlie <airlied@redhat.com>
um: Proper Fix for f25c80a4: remove duplicate structure field initialization
uml_net_set_mac() was broken and luckily it was never used, before.
What it was trying to do is spin_lock before memcopy the mac address.
Linus attempted to fix it in assumption that someone decided the
lock was needed. But since it was never ever used at all, and was
just dead code, I think we can assume that it is not needed, after
all.
On the other hand patch [f25c80a4] was trying to use eth_mac_addr()
in eth_configure(), *which was the real fallout*. Because of state
checks done inside eth_mac_addr() the address was never set. I have
not reintroduced the memcpy wrapper, but I've put a comment for future
cats.
The code now is back to exactly as it was before [f25c80a4]. With
the cleanup applied. If the spin_lock is indeed needed then a contender
should supply a test case that fails, then fix it with the proper
locking, as a separate unrelated patch.
CC: Julia Lawall <julia@diku.dk> CC: David S. Miller <davem@davemloft.net> CC: Andrew Morton <akpm@linux-foundation.org> CC: Al Viro <viro@ZenIV.linux.org.uk> Tested-by: Boaz Harrosh <bharrosh@panasas.com> Signed-off-by: Boaz Harrosh <bharrosh@panasas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
dmaengine: fix interrupt clearing for mv_xor
missing inline keyword for static function in linux/dmaengine.h
dma/shdma: move dereference below the NULL check
Joel Becker [Thu, 30 Sep 2010 00:33:05 +0000 (17:33 -0700)]
ocfs2: Don't walk off the end of fast symlinks.
ocfs2 fast symlinks are NUL terminated strings stored inline in the
inode data area. However, disk corruption or a local attacker could, in
theory, remove that NUL. Because we're using strlen() (my fault,
introduced in a731d1 when removing vfs_follow_link()), we could walk off
the end of that string.
Signed-off-by: Joel Becker <joel.becker@oracle.com> Cc: stable@kernel.org
...the following patch fixes it and seems to be the obviously correct
thing to do for cifs.
Cc: stable@kernel.org Acked-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com> Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com>
Jeff Layton [Wed, 22 Sep 2010 23:17:40 +0000 (16:17 -0700)]
cifs: fix handling of signing with writepages (try #6)
Get a reference to the file early so we can eventually base the decision
about signing on the correct tcon. If that doesn't work for some reason,
then fall back to generic_writepages. That's just as likely to fail, but
it simplifies the error handling.
In truth, I'm not sure how that could occur anyway, so maybe a NULL
open_file here ought to be a BUG()?
After that, we drop the reference to the open_file and then we re-get
one prior to each WriteAndX call. This helps ensure that the filehandle
isn't held open any longer than necessary and that open files are
reclaimed prior to each write call.
Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com>
Jeff Layton [Mon, 20 Sep 2010 23:01:35 +0000 (16:01 -0700)]
cifs: add cifs_sb_master_tcon and convert some callers to use it
At mount time, we'll always need to create a tcon that will serve as a
template for others that are associated with the mount. This tcon is
known as the "master" tcon.
In some cases, we'll need to use that tcon regardless of who's accessing
the mount. Add an accessor function for the master tcon and go ahead and
switch the appropriate places to use it.
Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com>
Jeff Layton [Mon, 20 Sep 2010 23:01:33 +0000 (16:01 -0700)]
cifs: add function to get a tcon from cifs_sb
When we convert cifs to do multiple sessions per mount, we'll need more
than one tcon per superblock. At that point "cifs_sb->tcon" will make
no sense. Add a new accessor function that gets a tcon given a cifs_sb.
For now, it just returns cifs_sb->tcon. Later it'll do more.
Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com>
Jeff Layton [Tue, 21 Sep 2010 15:14:46 +0000 (08:14 -0700)]
cifs: allow matching of tcp sessions in CifsNew state
With commit 7332f2a6217ee6925f83ef0e725013067ed316ba, cifsd will no
longer exit when the socket abends and the tcpStatus is CifsNew. With
that change, there's no reason to avoid matching an existing session in
this state.
Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com>
Jeff Layton [Mon, 20 Sep 2010 23:01:30 +0000 (16:01 -0700)]
cifs: add tcon field to cifsFileInfo struct
Eventually, we'll have more than one tcon per superblock. At that point,
we'll need to know which one is associated with a particular fid. For
now, this is just set from the cifs_sb->tcon pointer, but eventually
the caller of cifs_new_fileinfo will pass a tcon pointer in.
Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com>
This is the start for an implementation of "Minshall+French Symlinks"
(see http://wiki.samba.org/index.php/UNIX_Extensions#Minshall.2BFrench_symlinks).
Signed-off-by: Stefan Metzmacher <metze@samba.org> Signed-off-by: Steve French <sfrench@us.ibm.com>
If configured, Minshall+French Symlinks are used against
all servers. If the server supports UNIX Extensions,
we still create Minshall+French Symlinks on write,
but on read we fallback to UNIX Extension symlinks.
Signed-off-by: Stefan Metzmacher <metze@samba.org> Signed-off-by: Steve French <sfrench@us.ibm.com>
Ben Greear [Thu, 2 Sep 2010 00:06:02 +0000 (17:06 -0700)]
cifs: Allow binding to local IP address.
When using multi-homed machines, it's nice to be able to specify
the local IP to use for outbound connections. This patch gives
cifs the ability to bind to a particular IP address.
Usage: mount -t cifs -o srcaddr=192.168.1.50,user=foo, ...
Usage: mount -t cifs -o srcaddr=2002::100:1,user=foo, ...
Acked-by: Jeff Layton <jlayton@redhat.com> Acked-by: Dr. David Holder <david.holder@erion.co.uk> Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Steve French <sfrench@us.ibm.com>
cifs NTLMv2/NTLMSSP ntlmv2 within ntlmssp autentication code
Attribue Value (AV) pairs or Target Info (TI) pairs are part of
ntlmv2 authentication.
Structure ntlmv2_resp had only definition for two av pairs.
So removed it, and now allocation of av pairs is dynamic.
For servers like Windows 7/2008, av pairs sent by server in
challege packet (type 2 in the ntlmssp exchange/negotiation) can
vary.
Server sends them during ntlmssp negotiation. So when ntlmssp is used
as an authentication mechanism, type 2 challenge packet from server
has this information. Pluck it and use the entire blob for
authenticaiton purpose. If user has not specified, extract
(netbios) domain name from the av pairs which is used to calculate
ntlmv2 hash. Servers like Windows 7 are particular about the AV pair
blob.
Servers like Windows 2003, are not very strict about the contents
of av pair blob used during ntlmv2 authentication.
So when security mechanism such as ntlmv2 is used (not ntlmv2 in ntlmssp),
there is no negotiation and so genereate a minimal blob that gets
used in ntlmv2 authentication as well as gets sent.
Fields tilen and tilbob are session specific. AV pair values are defined.
To calculate ntlmv2 response we need ti/av pair blob.
For sec mech like ntlmssp, the blob is plucked from type 2 response from
the server. From this blob, netbios name of the domain is retrieved,
if user has not already provided, to be included in the Target String
as part of ntlmv2 hash calculations.
For sec mech like ntlmv2, create a minimal, two av pair blob.
The allocated blob is freed in case of error. In case there is no error,
this blob is used in calculating ntlmv2 response (in CalcNTLMv2_response)
and is also copied on the response to the server, and then freed.
The type 3 ntlmssp response is prepared on a buffer,
5 * sizeof of struct _AUTHENTICATE_MESSAGE, an empirical value large
enough to hold _AUTHENTICATE_MESSAGE plus a blob with max possible
10 values as part of ntlmv2 response and lmv2 keys and domain, user,
workstation names etc.
Also, kerberos gets selected as a default mechanism if server supports it,
over the other security mechanisms.
Signed-off-by: Shirish Pargaonkar <shirishpargaonkar@gmail.com> Signed-off-by: Steve French <sfrench@us.ibm.com>
cifs NTLMv2/NTLMSSP Change variable name mac_key to session key to reflect the key it holds
Change name of variable mac_key to session key.
The reason mac_key was changed to session key is, this structure does not
hold message authentication code, it holds the session key (for ntlmv2,
ntlmv1 etc.). mac is generated as a signature in cifs_calc* functions.
Signed-off-by: Shirish Pargaonkar <shirishpargaonkar@gmail.com> Signed-off-by: Steve French <sfrench@us.ibm.com>
cifs_new_fileinfo() does not use the 'oplock' value from the callers. Instead,
it sets it to REQ_OPLOCK which seems wrong. We should be using the oplock value
obtained from the Server to set the inode's clientCanCacheAll or
clientCanCacheRead flags. Fix this by passing oplock from the callers to
cifs_new_fileinfo().
This change dates back to commit a6ce4932 (2.6.30-rc3). So, all the affected
versions will need this fix. Please Cc stable once reviewed and accepted.
Cc: Stable <stable@kernel.org> Reviewed-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Suresh Jayaraman <sjayaraman@suse.de> Signed-off-by: Steve French <sfrench@us.ibm.com>
cifs: use type __u32 instead of int for the oplock parameter
... and avoid implicit casting from a signed type. Also, pass oplock by value
instead by reference as we don't intend to change the value in
cifs_open_inode_helper().
Thanks to Jeff Layton for spotting this.
Reviewed-by: Jeff Layton <jlayton@samba.org> Signed-off-by: Suresh Jayaraman <sjayaraman@suse.de> Signed-off-by: Steve French <sfrench@us.ibm.com>
ACPI, APEI, Fix ERST MOVE_DATA instruction implementation
The src_base and dst_base fields in apei_exec_context are physical
address, so they should be ioremaped before being used in ERST
MOVE_DATA instruction.
Reported-by: Javier Martinez Canillas <martinez.javier@gmail.com> Reported-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Huang Ying <ying.huang@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
Luis Henriques [Wed, 7 Jul 2010 18:30:15 +0000 (19:30 +0100)]
ACPI: fan: Fix more unbalanced code block
commit 934231de706d2579fae14f5857fcd8de991009ff fixes an unbalanced
CONFIG_ACPI_PROCFS code block during module initialisation. This
patch fixes similar issue but for the module exit.
Signed-off-by: Luis Henriques <luis.henrix@gmail.com> Signed-off-by: Len Brown <len.brown@intel.com>
In ERST debug/test support patch, a dynamic allocated buffer is
used. The may-failed memory allocation should be tried firstly before
free the previous buffer.
APEI resource management memory allocation related error path is fixed
too.
v2:
- Fix error messages for APEI resources management
Signed-off-by: Huang Ying <ying.huang@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
Jin Dongming [Wed, 29 Sep 2010 11:53:53 +0000 (19:53 +0800)]
ACPI, APEI, HEST Fix the unsuitable usage of platform_data
platform_data in hest_parse_ghes() is used for saving the address of entry
information of erst_tab. When the device is failed to be added, platform_data
will be freed by platform_device_put(). But the value saved in platform_data
should not be freed here. If it is done, it will make system panic.
So I think platform_data should save the address of allocated memory
which saves entry information of erst_tab.
This patch fixed it and I confirmed it on x86_64 next-tree.
v2:
Transport the pointer of hest_hdr to platform_data using
platform_device_add_data()
Signed-off-by: Jin Dongming <jin.dongming@np.css.fujitsu.com> Signed-off-by: Huang Ying <ying.huang@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
Jin Dongming [Wed, 29 Sep 2010 11:53:52 +0000 (19:53 +0800)]
ACPI, APEI, Fix acpi_pre_map() return value
After we ioremap() a new region, we call __acpi_try_ioremap() to
see whether another thread has already mapped the same region.
This check clobbers "vaddr", so compute the return value of
acpi_pre_map() using the ioremap() result "map->vaddr" instead.
v2:
Modified the unsuitable description of patch.
v3:
Removed unlikely() check and made description simpler.
Signed-off-by: Jin Dongming <jin.dongming@np.css.fujitsu.com> Reviewed-by: Andi Kleen <ak@linux.intel.com> Signed-off-by: Huang Ying <ying.huang@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
Dave Chinner [Fri, 24 Sep 2010 08:13:44 +0000 (18:13 +1000)]
xfs: force background CIL push under sustained load
I have been seeing occasional pauses in transaction throughput up to
30s long under heavy parallel workloads. The only notable thing was
that the xfsaild was trying to be active during the pauses, but
making no progress. It was running exactly 20 times a second (on the
50ms no-progress backoff), and the number of pushbuf events was
constant across this time as well. IOWs, the xfsaild appeared to be
stuck on buffers that it could not push out.
Further investigation indicated that it was trying to push out inode
buffers that were pinned and/or locked. The xfsbufd was also getting
woken at the same frequency (by the xfsaild, no doubt) to push out
delayed write buffers. The xfsbufd was not making any progress
because all the buffers in the delwri queue were pinned. This scan-
and-make-no-progress dance went one in the trace for some seconds,
before the xfssyncd came along an issued a log force, and then
things started going again.
However, I noticed something strange about the log force - there
were way too many IO's issued. 516 log buffers were written, to be
exact. That added up to 129MB of log IO, which got me very
interested because it's almost exactly 25% of the size of the log.
He delayed logging code is suppose to aggregate the minimum of 25%
of the log or 8MB worth of changes before flushing. That's what
really puzzled me - why did a log force write 129MB instead of only
8MB?
Essentially what has happened is that no CIL pushes had occurred
since the previous tail push which cleared out 25% of the log space.
That caused all the new transactions to block because there wasn't
log space for them, but they kick the xfsaild to push the tail.
However, the xfsaild was not making progress because there were
buffers it could not lock and flush, and the xfsbufd could not flush
them because they were pinned. As a result, both the xfsaild and the
xfsbufd could not move the tail of the log forward without the CIL
first committing.
The cause of the problem was that the background CIL push, which
should happen when 8MB of aggregated changes have been committed, is
being held off by the concurrent transaction commit load. The
background push does a down_write_trylock() which will fail if there
is a concurrent transaction commit holding the push lock in read
mode. With 8 CPUs all doing transactions as fast as they can, there
was enough concurrent transaction commits to hold off the background
push until tail-pushing could no longer free log space, and the halt
would occur.
It should be noted that there is no reason why it would halt at 25%
of log space used by a single CIL checkpoint. This bug could
definitely violate the "no transaction should be larger than half
the log" requirement and hence result in corruption if the system
crashed under heavy load. This sort of bug is exactly the reason why
delayed logging was tagged as experimental....
The fix is to start blocking background pushes once the threshold
has been exceeded. Rework the threshold calculations to keep the
amount of log space a CIL checkpoint can use to below that of the
AIL push threshold to avoid the problem completely.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Alex Elder <aelder@sgi.com> Reviewed-by: Christoph Hellwig <hch@lst.de>
Kevin Liu [Wed, 8 Sep 2010 13:44:36 +0000 (09:44 -0400)]
mfd: Fix max8925 irq control bit incorrect setting
In max8925_irq_sync_unlock(), irq control bit is set at the same time.
Zero means enabling irq, and one means disabling irq.
The original code is:
irq_chg[0] &= irq_data->enable;
It should be changed to:
irq_chg[0] &= ~irq_data->enable;
Otherwise, irq control bit is mess.
Signed-off-by: Kevin Liu <kliu5@marvell.com> Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
projects / ~andy / linux / log