Linus Torvalds [Tue, 11 Dec 2012 19:19:09 +0000 (11:19 -0800)]
Merge tag 'mmc-updates-for-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.8:
Core:
- Expose access to the eMMC RPMB ("Replay Protected Memory Block")
area by extending the existing mmc_block ioctl.
- Add SDIO powered-suspend DT properties to the core MMC DT binding.
- Add no-1-8-v DT flag for boards where the SD controller reports
that it supports 1.8V but the board itself has no way to switch to
1.8V.
- More work on switching to 1.8V UHS support using a vqmmc regulator.
- Fix up a case where the slot-gpio helper may fail to reset the host
controller properly if a card was removed during a transfer.
- Fix several cases where a broken device could cause an infinite
loop while we wait for a register to update.
Drivers:
- at91-mci: Remove obsolete driver, atmel-mci handles these devices
now.
- sdhci-dove: Allow using GPIOs for card-detect notifications.
- sdhci-esdhc: Fix for recovering from ADMA errors on broken silicon.
- sdhci-s3c: Add pinctrl support.
- wmt-sdmmc: New driver for WonderMedia SD/MMC controllers."
* tag 'mmc-updates-for-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (65 commits)
mmc: sdhci: implement the .card_event() method
mmc: extend the slot-gpio card-detection to use host's .card_event() method
mmc: add a card-event host operation
mmc: sdhci-s3c: Fix compilation warning
mmc: sdhci-pci: Enable SDHCI_CAN_DO_HISPD for Ricoh SDHCI controller
mmc: sdhci-dove: allow GPIOs to be used for card detection on Dove
mmc: sdhci-dove: use two-stage initialization for sdhci-pltfm
mmc: sdhci-dove: use devm_clk_get()
mmc: eSDHC: Recover from ADMA errors
mmc: dw_mmc: remove duplicated buswidth code
mmc: dw_mmc: relocate where dw_mci_setup_bus() is called from
mmc: Limit MMC speed to 52MHz if not HS200
mmc: dw_mmc: use devres functions in dw_mmc
mmc: sh_mmcif: remove unneeded clock connection ID
mmc: sh_mobile_sdhi: remove unneeded clock connection ID
mmc: sh_mobile_sdhi: fix clock frequency printing
mmc: Remove redundant null check before kfree in bus.c
mmc: Remove redundant null check before kfree in sdio_bus.c
mmc: sdhci-imx-esdhc: use more devm_* functions
mmc: dt: add no-1-8-v device tree flag
...
Florian Fainelli [Mon, 10 Dec 2012 20:25:32 +0000 (12:25 -0800)]
Input: matrix-keymap - provide proper module license
The matrix-keymap module is currently lacking a proper module license,
add one so we don't have this module tainting the entire kernel. This
issue has been present since commit 1932811f426f ("Input: matrix-keymap
- uninline and prepare for device tree support")
1) Netlink socket dumping had several missing verifications and checks.
In particular, address comparisons in the request byte code
interpreter could access past the end of the address in the
inet_request_sock.
Also, address family and address prefix lengths were not validated
properly at all.
This means arbitrary applications can read past the end of certain
kernel data structures.
Fixes from Neal Cardwell.
2) ip_check_defrag() operates in contexts where we're in the process
of, or about to, input the packet into the real protocols
(specifically macvlan and AF_PACKET snooping).
Unfortunately, it does a pskb_may_pull() which can modify the
backing packet data which is not legal if the SKB is shared. It
very much can be shared in this context.
Deal with the possibility that the SKB is segmented by using
skb_copy_bits().
Fix from Johannes Berg based upon a report by Eric Leblond.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
ipv4: ip_check_defrag must not modify skb before unsharing
inet_diag: validate port comparison byte code to prevent unsafe reads
inet_diag: avoid unsafe and nonsensical prefix matches in inet_diag_bc_run()
inet_diag: validate byte code to prevent oops in inet_diag_bc_run()
inet_diag: fix oops for IPv4 AF_INET6 TCP SYN-RECV state
This is a revert of a revert of a revert. In addition, it reverts the
even older i915 change to stop using the __GFP_NO_KSWAPD flag due to the
original commits in linux-next.
It turns out that the original patch really was bogus, and that the
original revert was the correct thing to do after all. We thought we
had fixed the problem, and then reverted the revert, but the problem
really is fundamental: waking up kswapd simply isn't the right thing to
do, and direct reclaim sometimes simply _is_ the right thing to do.
When certain allocations fail, we simply should try some direct reclaim,
and if that fails, fail the allocation. That's the right thing to do
for THP allocations, which can easily fail, and the GPU allocations want
to do that too.
So starting kswapd is sometimes simply wrong, and removing the flag that
said "don't start kswapd" was a mistake. Let's hope we never revisit
this mistake again - and certainly not this many times ;)
Acked-by: Mel Gorman <mgorman@suse.de> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Cc: Rik van Riel <riel@redhat.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johannes Berg [Sun, 9 Dec 2012 23:41:06 +0000 (23:41 +0000)]
ipv4: ip_check_defrag must not modify skb before unsharing
ip_check_defrag() might be called from af_packet within the
RX path where shared SKBs are used, so it must not modify
the input SKB before it has unshared it for defragmentation.
Use skb_copy_bits() to get the IP header and only pull in
everything later.
The same is true for the other caller in macvlan as it is
called from dev->rx_handler which can also get a shared SKB.
Reported-by: Eric Leblond <eric@regit.org> Cc: stable@vger.kernel.org Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
We are going to reinstate the __GFP_NO_KSWAPD flag that has been
removed, the removal reverted, and then removed again. Making this
commit a pointless fixup for a problem that was caused by the removal of
__GFP_NO_KSWAPD flag.
The thing is, we really don't want to wake up kswapd for THP allocations
(because they fail quite commonly under any kind of memory pressure,
including when there is tons of memory free), and these patches were
just trying to fix up the underlying bug: the original removal of
__GFP_NO_KSWAPD in commit c654345924f7 ("mm: remove __GFP_NO_KSWAPD")
was simply bogus.
Neal Cardwell [Sun, 9 Dec 2012 11:09:54 +0000 (11:09 +0000)]
inet_diag: validate port comparison byte code to prevent unsafe reads
Add logic to verify that a port comparison byte code operation
actually has the second inet_diag_bc_op from which we read the port
for such operations.
Previously the code blindly referenced op[1] without first checking
whether a second inet_diag_bc_op struct could fit there. So a
malicious user could make the kernel read 4 bytes beyond the end of
the bytecode array by claiming to have a whole port comparison byte
code (2 inet_diag_bc_op structs) when in fact the bytecode was not
long enough to hold both.
Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Neal Cardwell [Sat, 8 Dec 2012 19:43:23 +0000 (19:43 +0000)]
inet_diag: avoid unsafe and nonsensical prefix matches in inet_diag_bc_run()
Add logic to check the address family of the user-supplied conditional
and the address family of the connection entry. We now do not do
prefix matching of addresses from different address families (AF_INET
vs AF_INET6), except for the previously existing support for having an
IPv4 prefix match an IPv4-mapped IPv6 address (which this commit
maintains as-is).
This change is needed for two reasons:
(1) The addresses are different lengths, so comparing a 128-bit IPv6
prefix match condition to a 32-bit IPv4 connection address can cause
us to unwittingly walk off the end of the IPv4 address and read
garbage or oops.
(2) The IPv4 and IPv6 address spaces are semantically distinct, so a
simple bit-wise comparison of the prefixes is not meaningful, and
would lead to bogus results (except for the IPv4-mapped IPv6 case,
which this commit maintains).
Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Neal Cardwell [Sat, 8 Dec 2012 19:43:22 +0000 (19:43 +0000)]
inet_diag: validate byte code to prevent oops in inet_diag_bc_run()
Add logic to validate INET_DIAG_BC_S_COND and INET_DIAG_BC_D_COND
operations.
Previously we did not validate the inet_diag_hostcond, address family,
address length, and prefix length. So a malicious user could make the
kernel read beyond the end of the bytecode array by claiming to have a
whole inet_diag_hostcond when the bytecode was not long enough to
contain a whole inet_diag_hostcond of the given address family. Or
they could make the kernel read up to about 27 bytes beyond the end of
a connection address by passing a prefix length that exceeded the
length of addresses of the given family.
Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Neal Cardwell [Sat, 8 Dec 2012 19:43:21 +0000 (19:43 +0000)]
inet_diag: fix oops for IPv4 AF_INET6 TCP SYN-RECV state
Fix inet_diag to be aware of the fact that AF_INET6 TCP connections
instantiated for IPv4 traffic and in the SYN-RECV state were actually
created with inet_reqsk_alloc(), instead of inet6_reqsk_alloc(). This
means that for such connections inet6_rsk(req) returns a pointer to a
random spot in memory up to roughly 64KB beyond the end of the
request_sock.
With this bug, for a server using AF_INET6 TCP sockets and serving
IPv4 traffic, an inet_diag user like `ss state SYN-RECV` would lead to
inet_diag_fill_req() causing an oops or the export to user space of 16
bytes of kernel memory as a garbage IPv6 address, depending on where
the garbage inet6_rsk(req) pointed.
Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Weiner [Thu, 6 Dec 2012 20:23:25 +0000 (15:23 -0500)]
mm: vmscan: fix inappropriate zone congestion clearing
commit c702418f8a2f ("mm: vmscan: do not keep kswapd looping forever due
to individual uncompactable zones") removed zone watermark checks from
the compaction code in kswapd but left in the zone congestion clearing,
which now happens unconditionally on higher order reclaim.
This messes up the reclaim throttling logic for zones with
dirty/writeback pages, where zones should only lose their congestion
status when their watermarks have been restored.
Remove the clearing from the zone compaction section entirely. The
preliminary zone check and the reclaim loop in kswapd will clear it if
the zone is considered balanced.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Reviewed-by: Rik van Riel <riel@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 8 Dec 2012 00:48:39 +0000 (16:48 -0800)]
vfs: fix O_DIRECT read past end of block device
The direct-IO write path already had the i_size checks in mm/filemap.c,
but it turns out the read path did not, and removing the block size
checks in fs/block_dev.c (commit bbec0270bdd8: "blkdev_max_block: make
private to fs/buffer.c") removed the magic "shrink IO to past the end of
the device" code there.
Fix it by truncating the IO to the size of the block device, like the
write path already does.
NOTE! I suspect the write path would be *much* better off doing it this
way in fs/block_dev.c, rather than hidden deep in mm/filemap.c. The
mm/filemap.c code is extremely hard to follow, and has various
conditionals on the target being a block device (ie the flag passed in
to 'generic_write_checks()', along with a conditional update of the
inode timestamp etc).
It is also quite possible that we should treat this whole block device
size as a "s_maxbytes" issue, and try to make the logic even more
generic. However, in the meantime this is the fairly minimal targeted
fix.
Noted by Milan Broz thanks to a regression test for the cryptsetup
reencrypt tool.
Reported-and-tested-by: Milan Broz <mbroz@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking fixes from David Miller:
"Two stragglers:
1) The new code that adds new flushing semantics to GRO can cause SKB
pointer list corruption, manage the lists differently to avoid the
OOPS. Fix from Eric Dumazet.
2) When TCP fast open does a retransmit of data in a SYN-ACK or
similar, we update retransmit state that we shouldn't triggering a
WARN_ON later. Fix from Yuchung Cheng."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: gro: fix possible panic in skb_gro_receive()
tcp: bug fix Fast Open client retransmission
Eric Dumazet [Thu, 6 Dec 2012 13:54:59 +0000 (13:54 +0000)]
net: gro: fix possible panic in skb_gro_receive()
commit 2e71a6f8084e (net: gro: selective flush of packets) added
a bug for skbs using frag_list. This part of the GRO stack is rarely
used, as it needs skb not using a page fragment for their skb->head.
Most drivers do use a page fragment, but some of them use GFP_KERNEL
allocations for the initial fill of their RX ring buffer.
napi_gro_flush() overwrite skb->prev that was used for these skb to
point to the last skb in frag_list.
Fix this using a separate field in struct napi_gro_cb to point to the
last fragment.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuchung Cheng [Thu, 6 Dec 2012 08:45:32 +0000 (08:45 +0000)]
tcp: bug fix Fast Open client retransmission
If SYN-ACK partially acks SYN-data, the client retransmits the
remaining data by tcp_retransmit_skb(). This increments lost recovery
state variables like tp->retrans_out in Open state. If loss recovery
happens before the retransmission is acked, it triggers the WARN_ON
check in tcp_fastretrans_alert(). For example: the client sends
SYN-data, gets SYN-ACK acking only ISN, retransmits data, sends
another 4 data packets and get 3 dupacks.
Since the retransmission is not caused by network drop it should not
update the recovery state variables. Further the server may return a
smaller MSS than the cached MSS used for SYN-data, so the retranmission
needs a loop. Otherwise some data will not be retransmitted until timeout
or other loss recovery events.
Signed-off-by: Yuchung Cheng <ycheng@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Extracting a part of the SDHCI card tasklet into a .card_event()
implementation allows SDHCI hosts to use generic card-detection
services, e.g. the GPIO slot function.
mmc: extend the slot-gpio card-detection to use host's .card_event() method
The slot-gpio API provides a generic card-detection handler. To support a
wider range of hosts it has to call the host's card-event callback, if
implemented. Also increase the debounce interval to 200ms to match the
SDHCI driver.
Sachin Kamat [Tue, 4 Dec 2012 11:33:07 +0000 (17:03 +0530)]
mmc: sdhci-s3c: Fix compilation warning
'sc' is used only when CONFIG_PM_RUNTIME is defined. Hence define it
conditionally.
Silences the following warning:
drivers/mmc/host/sdhci-s3c.c: In function ‘sdhci_s3c_notify_change’:
drivers/mmc/host/sdhci-s3c.c:378:20: warning: unused variable ‘sc’ [-Wunused-variable]
Mel Gorman [Wed, 5 Dec 2012 22:01:41 +0000 (14:01 -0800)]
tmpfs: fix shared mempolicy leak
This fixes a regression in 3.7-rc, which has since gone into stable.
Commit 00442ad04a5e ("mempolicy: fix a memory corruption by refcount
imbalance in alloc_pages_vma()") changed get_vma_policy() to raise the
refcount on a shmem shared mempolicy; whereas shmem_alloc_page() went
on expecting alloc_page_vma() to drop the refcount it had acquired.
This deserves a rework: but for now fix the leak in shmem_alloc_page().
Hugh: shmem_swapin() did not need a fix, but surely it's clearer to use
the same refcounting there as in shmem_alloc_page(), delete its onstack
mempolicy, and the strange mpol_cond_copy() and __mpol_cond_copy() -
those were invented to let swapin_readahead() make an unknown number of
calls to alloc_pages_vma() with one mempolicy; but since 00442ad04a5e,
alloc_pages_vma() has kept refcount in balance, so now no problem.
Johannes Weiner [Tue, 4 Dec 2012 16:11:31 +0000 (11:11 -0500)]
mm: vmscan: do not keep kswapd looping forever due to individual uncompactable zones
When a zone meets its high watermark and is compactable in case of
higher order allocations, it contributes to the percentage of the node's
memory that is considered balanced.
This requirement, that a node be only partially balanced, came about
when kswapd was desparately trying to balance tiny zones when all bigger
zones in the node had plenty of free memory. Arguably, the same should
apply to compaction: if a significant part of the node is balanced
enough to run compaction, do not get hung up on that tiny zone that
might never get in shape.
When the compaction logic in kswapd is reached, we know that at least
25% of the node's memory is balanced properly for compaction (see
zone_balanced and pgdat_balanced). Remove the individual zone checks
that restart the kswapd cycle.
Otherwise, we may observe more endless looping in kswapd where the
compaction code loops back to reclaim because of a single zone and
reclaim does nothing because the node is considered balanced overall.
Mel Gorman [Thu, 6 Dec 2012 19:01:14 +0000 (19:01 +0000)]
mm: compaction: validate pfn range passed to isolate_freepages_block
Commit 0bf380bc70ec ("mm: compaction: check pfn_valid when entering a
new MAX_ORDER_NR_PAGES block during isolation for migration") added a
check for pfn_valid() when isolating pages for migration as the scanner
does not necessarily start pageblock-aligned.
Since commit c89511ab2f8f ("mm: compaction: Restart compaction from near
where it left off"), the free scanner has the same problem. This patch
makes sure that the pfn range passed to isolate_freepages_block() is
within the same block so that pfn_valid() checks are unnecessary.
In answer to Henrik's wondering why others have not reported this:
reproducing this requires a large enough hole with the right aligment to
have compaction walk into a PFN range with no memmap. Size and
alignment depends in the memory model - 4M for FLATMEM and 128M for
SPARSEMEM on x86. It needs a "lucky" machine.
mmc: sdhci-pci: Enable SDHCI_CAN_DO_HISPD for Ricoh SDHCI controller
The Ricoh SDHCI controllers support Highspeed clocks as evident from
the ricoh_mmc_probe_slot() settings. Hence, SDHCI_CAN_DO_HISPD needs
to be set to enable SDIO client drivers to set/enable high speed clock
settings
Signed-off-by: Madhvapathi Sriram <Madhvapathi.Sriram@csr.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Haijun Zhang [Tue, 4 Dec 2012 02:41:28 +0000 (10:41 +0800)]
mmc: eSDHC: Recover from ADMA errors
A-003500: False ADMA Error might be reported when ADMA is used for
multiple block read command with Stop at Block Gap. If PROCTL[SABGREQ]
is set when the particular block's data is received by the System side
logic before entire block (with CRC) data is received by the SD side
logic, and also if ADMA descriptor line is fetched at the same time,
then DMA engine might report false ADMA error. eSDHC might not be able
to Continue (PROCTL[CREQ]=1) after Stop at Block Gap.
This issue will impact the eSDHC IP VVN2.3.
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com> Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com> Acked-by: Anton Vorontsov <cbouatmailru@gmail.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Jaehoon Chung [Thu, 8 Nov 2012 08:35:29 +0000 (17:35 +0900)]
mmc: dw_mmc: relocate where dw_mci_setup_bus() is called from
To ensure the stable clock need to enable before set the
DW_MMC_CARD_NEED_INIT flag. If set DW_MMC_CARD_NEED_INIT flag,
wait for 80-clock before first command after power-up.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Seungwon Jeon <tgih.jun@samsung.com> Acked-by: Will Newton <will.newton@imgtec.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Al Cooper [Fri, 30 Nov 2012 15:53:35 +0000 (10:53 -0500)]
mmc: Limit MMC speed to 52MHz if not HS200
If "caps2" host capabilities does not indicate support for MMC
HS200, don't allow clock speeds >52MHz. Currently, for MMC, the
clock speed is set to the lesser of the max speed the eMMC module
supports (card->ext_csd.hs_max_dtr) or the max base clock of the
host controller (host->f_max based on BASE_CLK_FREQ in the host
CAPS register). This means that a host controller that doesn't
support HS200 mode but has a base clock of 100MHz and an eMMC module
that supports HS200 speeds will end up using a 100MHz clock.
Signed-off-by: Al Cooper <alcooperx@gmail.com> Signed-off-by: Chris Ball <cjb@laptop.org>
mmc: sh_mmcif: remove unneeded clock connection ID
MMCIF only uses one clock, all ARM and SuperH platforms register MMCIF
clock lookup entries with no connection ID, hence it can be dropped in
the driver too.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Chris Ball <cjb@laptop.org>
mmc: sh_mobile_sdhi: remove unneeded clock connection ID
SDHI only uses one clock, all ARM and SuperH platform register SDHI clock
lookup entries with no connection ID, hence it can be dropped in the
driver too.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Chris Ball <cjb@laptop.org>
During its probing the SDHI driver prints out the clock frequency, but
does it wrongly, always reporting 0Hz. Use the MMC host frequency value
to fix this issue.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Chris Ball <cjb@laptop.org>
Daniel Drake [Sun, 25 Nov 2012 18:02:54 +0000 (13:02 -0500)]
mmc: dt: add no-1-8-v device tree flag
The OLPC XO-1.75 laptop includes a SDHCI controller which is 1.8v
capable, and it truthfully reports so in its capabilities. This
alternate voltage is used for driving new "UHS-I" SD cards at their
full speed.
However, what the controller doesn't know is that the motherboard
physically doesn't have a 1.8v supply available, so attempting to
switch to the 1.8v level will result in a situation that cannot be
recovered from without physically replugging the SD card.
Add a device tree flag that can be used on systems like these,
and hook it up to the equivalent SDHCI quirk.
Signed-off-by: Daniel Drake <dsd@laptop.org> Reviewed-by: Philip Rakity <prakity@nvidia.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Daniel Drake [Sun, 25 Nov 2012 18:01:19 +0000 (13:01 -0500)]
mmc: sdhci: add quirk for lack of 1.8v support
The OLPC XO-1.75 laptop includes a SDHCI controller which is 1.8v
capable, and it truthfully reports so in its capabilities. This
alternate voltage is used for driving new "UHS-I" SD cards at their
full speed.
However, what the controller doesn't know is that the motherboard
physically doesn't have a 1.8v supply available.
Add a quirk so that systems such as this one can override disable
1.8v support, adding support for UHS-I cards (by running them at
3.3v).
This avoids a problem where the system would first try to run the
card at 1.8v, fail, and then not be able to fully reset the card
to retry at the normal 3.3v voltage.
This is more appropriate than using the MISSING_CAPS quirk, which
is intended for cases where the SDHCI controller is actually lying
about its capabilities, and would force us to somehow override both
caps words from another source.
Signed-off-by: Daniel Drake <dsd@laptop.org> Reviewed-by: Philip Rakity <prakity@nvidia.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Suspend methods provided by SDIO drivers are not supposed to be called by
the PM core. Instead, when the SDIO core gets to suspend a device's
ancestor, it calls the device driver's suspend routine. However, the PM
core executes suspend callback routines directly for device drivers whose
bus types don't provide suspend callbacks. In consequece, because the
SDIO bus type doesn't provide a suspend callback, the SDIO drivers'
suspend routines will be executed by the PM core (which shouldn't
happen).
To prevent this from happening, add empty system suspend/resume callbacks
for the SDIO bus type.
An analogous change had been made already by commit (e841a7c mmc: sdio:
Use empty system suspend/resume callbacks at the bus level), but then it
was reverted inadvertently by commit (d8e2ac3 mmc: sdio: Fix PM_SLEEP
related build warnings) that attempted to fix build warnings introduced
by commit e841a7c.
Reported-by: NeilBrown <neilb@suse.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Viresh Kumar [Thu, 8 Nov 2012 15:09:10 +0000 (20:39 +0530)]
mmc: sdhci-spear: Don't call clk_{un}prepare() in suspend/resume
clk_{un}prepare is mandatory for platforms using common clock
framework. Because for SPEAr we don't do anything in clk_{un}prepare()
calls, just call them once in probe/remove.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
Tomasz Figa [Sun, 25 Nov 2012 20:40:44 +0000 (15:40 -0500)]
mmc: host: sdhci-s3c: Use devm_gpio_request to request GPIOs
The set of GPIO pins used by sdhci-s3c driver varies between
configurations, such as card detect method, pinctrl availability, etc.
This overly complicates the code requesting and freeing GPIO pins, which
must check which pins are used, when freeing them.
This patch modifies the sdhci-s3c driver to use devm_gpio_request to
free requested pins automatically after unbinding the driver.
Signed-off-by: Tomasz Figa <t.figa@samsung.com> Acked-by: Thomas Abraham <thomas.abraham@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
Jerry Huang [Fri, 23 Nov 2012 09:25:03 +0000 (17:25 +0800)]
mmc: sdhci-of-esdhc: support commands with busy response expecting TC
The IP versions older than 2.3 didn't support commands with busy
response which expect the TC bit set. But after the VVN2.3, eSDHC
IP has supported it.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Tushar Behera [Tue, 20 Nov 2012 04:11:53 +0000 (09:41 +0530)]
mmc: sdhci-s3c: Use NULL instead of 0 for pointers
The third argument for of_get_property() is a pointer, hence pass
NULL instead of 0.
Fixes the following sparse warning:
sdhci-s3c.c:452:48: warning: Using plain integer as NULL pointer
sdhci-s3c.c:457:52: warning: Using plain integer as NULL pointer
Signed-off-by: Tushar Behera <tushar.behera@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
prepare() is supposed to prevent new children from being registered.
On the MMC subsystem, children (new cards) registration starts with
the card detect IRQ.
Move card detect IRQ disabling to prepare() so that no new cards
will be registered while we're trying to suspend.
Likewise, move card detect IRQ enabling to complete() so we only
try to register new children after our MMC IP is back up.
Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Venkatraman S <svenkatr@ti.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Hebbar, Gururaja [Mon, 19 Nov 2012 16:29:58 +0000 (21:59 +0530)]
mmc: omap_hsmmc: Enable HSPE bit for high speed cards
HSMMC IP on AM33xx need a special setting to handle High-speed cards.
Other platforms like TI81xx, OMAP4 may need this as-well. This depends
on the HSMMC IP timing closure done for the high speed cards.
From AM335x TRM (SPRUH73F - 18.3.12 Output Signals Generation):
The MMC/SD/SDIO output signals can be driven on either falling edge or
rising edge depending on the SD_HCTL[2] HSPE bit. This feature allows
to reach better timing performance, and thus to increase data transfer
frequency.
There are few pre-requisites for enabling the HSPE bit
- Controller should support High-Speed-Enable Bit and
- Controller should not be using DDR Mode and
- Controller should advertise that it supports High Speed in
capabilities register and
- MMC/SD clock coming out of controller > 25MHz
Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com> Signed-off-by: Venkatraman S <svenkatr@ti.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Balaji T K [Mon, 19 Nov 2012 16:29:57 +0000 (21:59 +0530)]
mmc: omap_hsmmc: Update error code for response_busy cmd
Update error code to cmd->error for commands with response_busy and no data.
Signed-off-by: Balaji T K <balajitk@ti.com> Reviewed-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Venkatraman S <svenkatr@ti.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Balaji T K [Mon, 19 Nov 2012 16:29:56 +0000 (21:59 +0530)]
mmc: omap_hsmmc: No reset of cmd state machine for DCRC
Avoid soft reset of command internal state machine on data errors.
Signed-off-by: Balaji T K <balajitk@ti.com> Reviewed-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Venkatraman S <svenkatr@ti.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Balaji T K [Mon, 19 Nov 2012 16:29:55 +0000 (21:59 +0530)]
mmc: omap_hsmmc: Fix Oops in case of data errors
ae4bf788ee9 ("mmc: omap_hsmmc: consolidate error report handling of HSMMC
IRQ") sets both end_cmd and end_trans to 1.
Setting end_cmd to 1 for Data Timeout/CRC leads to NULL pointer dereference of
host->cmd as the command complete has previously been handled.
Set end_cmd only in case of command Timeout/CRC.
Moreover host->cmd->error should not be updated on data error case, only
host->data->error needs to be updated.
Signed-off-by: Balaji T K <balajitk@ti.com> Reviewed-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Venkatraman S <svenkatr@ti.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Kevin Liu [Tue, 20 Nov 2012 13:24:32 +0000 (08:24 -0500)]
mmc: sdhci: Use regulator min/max voltage range according to spec
For regulator vmmc/vmmcq, use voltage range as below
3.3v/3.0v: (2.7v, 3.6v)
1.8v: (1.7v, 1.95v)
Original code uses the precise value which may fail in regulator
driver if it does NOT support the precise voltage.
Signed-off-by: Jialing Fu <jlfu@marvell.com> Signed-off-by: Kevin Liu <kliu5@marvell.com> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Loic Pallardy [Mon, 6 Aug 2012 15:12:31 +0000 (17:12 +0200)]
mmc: card: Add RPMB support in IOCTL interface
RPMB partition is accessing though /dev/block/mmcXrpmb device
User callers can read and write entire data frame(s) as defined
by JEDEC Standard JESD84-A441, using standard IOCTL interface.
Loic Pallardy [Sat, 17 Nov 2012 23:08:24 +0000 (18:08 -0500)]
mmc: core: Expose access to RPMB partition
Following JEDEC standard, if the mmc supports RPMB partition,
a new interface is created and exposed via /dev/block.
Users will be able to access RPMB partition using standard
mmc IOCTL commands.
Signed-off-by: Alex Macro <alex.macro@stericsson.com> Signed-off-by: Loic Pallardy <loic.pallardy@stericsson.com> Reviewed-by: Namjae Jeon <linkinjeon@gmail.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Johan Rudholm <johan.rudholm@stericsson.com> Acked-by: Krishna Konda <kkonda@codeaurora.org> Signed-off-by: Chris Ball <cjb@laptop.org>
Kevin Liu [Wed, 17 Oct 2012 11:04:46 +0000 (19:04 +0800)]
mmc: host: Make UHS timing values fully unique
Both of MMC_TIMING_LEGACY and MMC_TIMING_UHS_SDR12 are defined
to 0. And ios->timing is set to MMC_TIMING_LEGACY during power up.
But set_ios can't distinguish these two timing if host support
spec 3.0. Just adjust timing values to be different can resolve
this issue without any other impact.
Reviewed-by: Girish K S <girish.shivananjappa@linaro.org> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Kevin Liu <kliu5@marvell.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Kevin Liu [Wed, 17 Oct 2012 11:04:45 +0000 (19:04 +0800)]
mmc: sdhci-pxav3: Add base clock quirk
Enable the quirk SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN since
SD_CAPABILITIES_1[15:8](BASE_FREQ) can't get correct base clock value.
It returns a fixed pre-set value like 200 on some sdhci-pxav3 based
platforms like MMP3 while return 0 on the other sdhci-pxav3 based
platforms. So we enable the quirk and get the base clock via function
get_max_clock. Also add get_max_clock.
Reported-by: Philip Rakity <prakity@marvell.com> Reviewed-by: Philip Rakity <prakity@Marvell.com> Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com> Signed-off-by: Kevin Liu <kliu5@marvell.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Kyoungil Kim [Mon, 22 Oct 2012 11:01:00 +0000 (20:01 +0900)]
mmc: sdio: Use multiple scatter/gather list
Before this patch, we always used only single sg entry for SDIO transfer.
This patch switches to using multiple sg entries. In the case of dwmci,
it supports only up to 4KB size per single sg entry. So if we want to
transfer more than 4KB, we should send more than 1 command.
When we tested before applying this patch, it took around 335 us for
5K(5120) bytes transfer with dwmci controller. After applying this patch,
it takes 242 us for 5K bytes. So this patch makes around 38% performance
improvement for 5K bytes transfer. If the transfer size is bigger, then
the performance improvement ratio will be increased.
Signed-off-by: Kyoungil Kim <ki0351.kim@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Trey Ramsay [Fri, 16 Nov 2012 15:31:41 +0000 (09:31 -0600)]
mmc: core: Fix some driver hangs when dealing with broken devices
There are infinite loops in the mmc code that can be caused by bad
hardware. The code will loop forever if the device never comes back
from program mode, R1_STATE_PRG, and it is not ready for data,
R1_READY_FOR_DATA.
A long timeout is added to prevent the code from looping forever.
The timeout will occur if the device never comes back from program
state or the device never becomes ready for data.
It's not clear whether the timeout will do more than log a pr_err()
and then start a fresh hang all over again. We may need to extend
this patch later to perform some kind of reset of the device (is
that possible?) or rejection of new I/O to the device.
Signed-off-by: Trey Ramsay <tramsay@linux.vnet.ibm.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Arnd Bergmann [Thu, 8 Nov 2012 14:26:11 +0000 (14:26 +0000)]
mmc: dw_mmc: fix more const pointer warnings
The patch "dw_mmc: fix multiple drv_data NULL dereferences" has
unfortunately clashed with my "mmc: dw_mmc: constify dw_mci_idmac_ops
in exynos back-end" patch, causing new warnings to appear.
This should hopefully fix the issue for good.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Chris Ball <cjb@laptop.org>
Balaji T K [Thu, 25 Oct 2012 15:58:35 +0000 (21:28 +0530)]
mmc: omap_hsmmc: remove warning message for debounce clock
MMC debounce clock is applicable only for omap2430, warning message gets
printed when enable fails for debounce clock. Remove the get debounce clock
failure message as it is noisy for other platforms.
Signed-off-by: Balaji T K <balajitk@ti.com> Reported-by: Russell King <rmk+kernel@arm.linux.org.uk> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Javier Martin [Tue, 30 Oct 2012 15:54:07 +0000 (16:54 +0100)]
mmc: mxcmmc: fix SD cards not being detected sometimes.
When a SD card is initialized some data transfers of 64 and 8 bytes
are issued. It seems the DMA has some problems dealing with these kind
of "short" transfers, leading sometimes to the SD card not being detected.
In order to solve this problem, do not use DMA for transfer sizes lower
than the sector size.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Chris Ball <cjb@laptop.org>
Andy Shevchenko [Wed, 3 Oct 2012 13:26:37 +0000 (16:26 +0300)]
mmc: dw_mmc: use helper macro module_platform_driver()
Since v3.2 we have nice macro to define the platform driver's init and exit
calls. This patch simplifies the dw_mmc platform driver by using that macro.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Girish K S <girish.shivanajappa@linaro.org> Acked-by: Will Newton <will.newton@imgtec.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Andy Shevchenko [Wed, 3 Oct 2012 13:45:23 +0000 (16:45 +0300)]
mmc: dw_mmc: use __devexit_p macro for .remove()
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Girish K S <girish.shivananjappa@linaro.org> Acked-by: Will Newton <will.newton@imgtec.com> Signed-off-by: Chris Ball <cjb@laptop.org>
mmc: queue: amend buffer swap for non-blocking transfer
In case both 'req' and 'mq->mqrq_prev->req' are null, there is no request
to be processed. That means there is no need to switch buffer.
Switching buffer is required only after finishing 'issue_fn'.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com> Reviewed-by: Per Forlin <per.forlin@stericsson.com> Tested-by: Johan Rudholm <johan.rudholm@stericsson.com> Signed-off-by: Chris Ball <cjb@laptop.org>
mmc: sh-mmcif: avoid oops on spurious interrupts (second try)
On some systems, e.g., kzm9g, MMCIF interfaces can produce spurious
interrupts without any active request. To prevent the Oops, that results
in such cases, don't dereference the mmc request pointer until we make
sure, that we are indeed processing such a request.
Kevin Liu [Sat, 17 Nov 2012 22:55:51 +0000 (17:55 -0500)]
mmc: sdhci: Balance vmmc regulator_enable(), and always enable vqmmc
The vmmc regulator enable in sdhci_add_host is NOT necessary since
it can be enabled during mmc_power_up by function mmc_regulator_set_ocr.
And this extra enable will make regulator_enable/regulator_disable
unbalanced. Consequently, vmmc can't be disabled during mmc_power_off.
Also, if the vqmmc regulator exists, it should be enabled regardless it
support 1.8v or not.
Signed-off-by: Kevin Liu <kliu5@marvell.com> Signed-off-by: Philip Rakity <prakity@marvell.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Heiko Stübner [Sun, 18 Nov 2012 18:50:05 +0000 (19:50 +0100)]
mmc: sdhci-s3c: fix missing clock for gpio card-detect
2abeb5c5ded2 ("Add clk_(enable/disable) in runtime suspend/resume")
added the capability to stop the clocks when the device is runtime
suspended, but forgot to handle the case of the card-detect using
an external gpio.
Therefore in the case that runtime-pm is enabled, start the io-clock
when a card is inserted and stop it again once it is removed.
Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Chris Ball <cjb@laptop.org>
Linus Torvalds [Thu, 6 Dec 2012 16:42:13 +0000 (08:42 -0800)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
"These are the fixes for the N32 syscall bugs found by Al, an
extraneous break that broke detection for R3000 and R3081 processors,
an endless loop processing signals for kernel task (x86 received the
same fix a while ago) and a fix for transparent huge page which took
ages to track down because it was so hard to come up with a workable
test case."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Fix endless loop when processing signals for kernel tasks
MIPS: R3000/R3081: Fix CPU detection.
MIPS: N32: Fix signalfd4 syscall entry point
MIPS: N32: Fix preadv(2) and pwritev(2) entry points.
MIPS: Avoid mcheck by flushing page range in huge_ptep_set_access_flags()
Linus Torvalds [Thu, 6 Dec 2012 16:39:57 +0000 (08:39 -0800)]
Merge branch 'more-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull build fix from Rusty Russell:
"Tim Gardner <tim.gardner@canonical.com> writes:
> It is $(obj)/oid_registry.o that is dependent on $(obj)/oid_registry_data.c.
> The object file cannot be built until $(obj)/oid_registry_data.c has been
> generated.
>
> A periodic and hard to reproduce parallel build failure is due to
> this incorrect lib/Makefile dependency. The compile error is completely
> disingenuous.
>
> GEN lib/oid_registry_data.c
> Compiling 49 OIDs
> CC lib/oid_registry.o
> gcc: error: lib/oid_registry.c: No such file or directory
> gcc: fatal error: no input files
> compilation terminated.
> make[3]: *** [lib/oid_registry.o] Error 4
I can't reproduce it either. It's completely weird; nothing ever
removes lib/oid_registry.c, so either gcc is giving the wrong message
or it's a weird fs with a very odd race.
But your version is definitely more correct than the previous one,
so..."
* 'more-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
lib/Makefile: Fix oid_registry build dependency
Linus Torvalds [Thu, 6 Dec 2012 16:29:08 +0000 (08:29 -0800)]
Merge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module signing fixes from Rusty Russell:
"David gave me these a month ago, during my git workflow churn :("
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
ASN.1: Fix an indefinite length skip error
MODSIGN: Don't use enum-type bitfields in module signature info block
Tim Gardner [Tue, 4 Dec 2012 19:52:28 +0000 (12:52 -0700)]
lib/Makefile: Fix oid_registry build dependency
It is $(obj)/oid_registry.o that is dependent on $(obj)/oid_registry_data.c.
The object file cannot be built until $(obj)/oid_registry_data.c has been
generated.
A periodic and hard to reproduce parallel build failure is due to
this incorrect lib/Makefile dependency. The compile error is completely
disingenuous.
GEN lib/oid_registry_data.c
Compiling 49 OIDs
CC lib/oid_registry.o
gcc: error: lib/oid_registry.c: No such file or directory
gcc: fatal error: no input files
compilation terminated.
make[3]: *** [lib/oid_registry.o] Error 4
Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Akinobu Mita <akinobu.mita@gmail.com> Cc: Michel Lespinasse <walken@google.com> Cc: David Howells <dhowells@redhat.com> Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
MIPS: Fix endless loop when processing signals for kernel tasks
The problem occurs [1] when a kernel-mode task returns from a system
call with a pending signal.
A real-life scenario is a child of 'khelper' returning from a failed
kernel_execve() in ____call_usermodehelper() [ kernel/kmod.c ].
kernel_execve() fails due to a pending SIGKILL, which is the result of
"kill -9 -1" (at least, busybox's init does it upon reboot).
The loop is as follows:
* syscall_exit_work:
- work_pending: // start_of_the_loop
- work_notifysig:
- do_notify_resume()
- do_signal()
- if (!user_mode(regs)) return;
- resume_userspace // TIF_SIGPENDING is still set
- work_pending // so we call work_pending => goto
// start_of_the_loop
More information can be found in another LKML thread:
http://www.serverphorums.com/read.php?12,457826
[1] The problem was also reproduced on !CONFIG_VM86 x86, and the
following fix was accepted.
David Howells [Mon, 22 Oct 2012 14:05:55 +0000 (15:05 +0100)]
ASN.1: Fix an indefinite length skip error
Fix an error in asn1_find_indefinite_length() whereby small definite length
elements of size 0x7f are incorrecly classified as non-small. Without this
fix, an error will be given as the length of the length will be perceived as
being very much greater than the maximum supported size.
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
David Howells [Mon, 22 Oct 2012 14:05:48 +0000 (15:05 +0100)]
MODSIGN: Don't use enum-type bitfields in module signature info block
Don't use enum-type bitfields in the module signature info block as we can't be
certain how the compiler will handle them. As I understand it, it is arch
dependent, and it is possible for the compiler to rearrange them based on
endianness and to insert a byte of padding to pad the three enums out to four
bytes.
Instead use u8 fields for these, which the compiler should emit in the right
order without padding.
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Thomas Gleixner [Tue, 4 Dec 2012 17:59:34 +0000 (18:59 +0100)]
watchdog: Fix CPU hotplug regression
Norbert reported:
"3.7-rc6 booted with nmi_watchdog=0 fails to suspend to RAM or
offline CPUs. It's reproducable with a KVM guest and physical
system."
The reason is that commit bcd951cf(watchdog: Use hotplug thread
infrastructure) missed to take this into account. So the cpu offline
code gets stuck in the teardown function because it accesses non
initialized data structures.
Add a check for watchdog_enabled into that path to cure the issue.
projects / ~andy / linux / log