Johan Hedberg [Wed, 25 Sep 2013 10:26:10 +0000 (13:26 +0300)]
Bluetooth: Add new mgmt_set_advertising command
This patch adds a new mgmt command for enabling and disabling
LE advertising. The command depends on the LE setting being enabled
first and will return a "rejected" response otherwise. The patch also
adds safeguards so that there will ever only be one set_le or
set_advertising command pending per adapter.
The response handling and new_settings event sending is done in an
asynchronous request callback, meaning raw HCI access from user space to
enable advertising (e.g. hciconfig leadv) will not trigger the
new_settings event. This is intentional since trying to support mixed
raw HCI and mgmt access would mean adding extra state tracking or new
helper functions, essentially negating the benefit of using the
asynchronous request framework. The HCI_LE_ENABLED and HCI_LE_PERIPHERAL
flags however are updated correctly even with raw HCI access so this
will not completely break subsequent access over mgmt.
Johan Hedberg [Wed, 25 Sep 2013 10:26:09 +0000 (13:26 +0300)]
Bluetooth: Add new mgmt setting for LE advertising
This patch adds a new mgmt setting for LE advertising and hooks up the
necessary places in the mgmt code to operate on the HCI_LE_PERIPHERAL
flag (which corresponds to this setting). This patch does not yet add
any new command for enabling the setting - that is left for a subsequent
patch.
Johan Hedberg [Wed, 25 Sep 2013 10:26:08 +0000 (13:26 +0300)]
Bluetooth: Use async request for LE enable/disable
This patch updates the code to use an asynchronous request for handling
the enabling and disabling of LE support. This refactoring is necessary
as a preparation for adding advertising support, since when LE is
disabled we should also disable advertising, and the cleanest way to do
this is to perform the two respective HCI commands in the same
asynchronous request.
Johan Hedberg [Wed, 25 Sep 2013 10:26:07 +0000 (13:26 +0300)]
Bluetooth: Move mgmt response convenience functions to a better location
The settings_rsp and cmd_status_rsp functions can be useful for all mgmt
command handlers when asynchronous request callbacks are used. They will
e.g. be used by subsequent patches to change set_le to use an async
request as well as a new set_advertising command. Therefore, move them
higher up in the mgmt.c file to avoid unnecessary forward declarations
or mixing this trivial change with other patches.
Johan Hedberg [Wed, 25 Sep 2013 10:26:06 +0000 (13:26 +0300)]
Bluetooth: Fix busy return for mgmt_set_powered in some cases
We should return a "busy" error always when there is another
mgmt_set_powered operation in progress. Previously when powering on
while the auto off timer was still set the code could have let two or
more pending power on commands to be queued. This patch fixes the issue
by moving the check for duplicate commands to an earlier point in the
set_powered handler.
Johan Hedberg [Wed, 25 Sep 2013 10:26:05 +0000 (13:26 +0300)]
Bluetooth: Clean up socket locking in l2cap_sock_recvmsg
This patch cleans up the locking login in l2cap_sock_recvmsg by pairing
up each lock_sock call with a release_sock call. The function already
has a "done" label that handles releasing the socket and returning from
the function so the fix is rather simple.
Gianluca Anzolin [Tue, 27 Aug 2013 16:28:46 +0000 (18:28 +0200)]
Bluetooth: don't release the port in rfcomm_dev_state_change()
When the dlc is closed, rfcomm_dev_state_change() tries to release the
port in the case it cannot get a reference to the tty. However this is
racy and not even needed.
Infact as Peter Hurley points out:
1. Only consider dlcs that are 'stolen' from a connected socket, ie.
reused. Allocated dlcs cannot have been closed prior to port
activate and so for these dlcs a tty reference will always be avail
in rfcomm_dev_state_change() -- except for the conditions covered by
#2b below.
2. If a tty was at some point previously created for this rfcomm, then
either
(a) the tty reference is still avail, so rfcomm_dev_state_change()
will perform a hangup. So nothing to do, or,
(b) the tty reference is no longer avail, and the tty_port will be
destroyed by the last tty_port_put() in rfcomm_tty_cleanup.
Again, no action required.
3. Prior to obtaining the dlc lock in rfcomm_dev_add(),
rfcomm_dev_state_change() will not 'see' a rfcomm_dev so nothing to
do here.
4. After releasing the dlc lock in rfcomm_dev_add(),
rfcomm_dev_state_change() will 'see' an incomplete rfcomm_dev if a
tty reference could not be obtained. Again, the best thing to do here
is nothing. Any future attempted open() will block on
rfcomm_dev_carrier_raised(). The unconnected device will exist until
released by ioctl(RFCOMMRELEASEDEV).
The patch removes the aforementioned code and uses the
tty_port_tty_hangup() helper to hangup the tty.
Johan Hedberg [Fri, 13 Sep 2013 08:40:02 +0000 (11:40 +0300)]
Bluetooth: Add event mask page 2 setting support
For those controller that support the HCI_Set_Event_Mask_Page_2 command
we should include it in the init sequence. This patch implements sending
of the command and enables the events in it based on supported features
(currently only CSB is checked).
Johan Hedberg [Fri, 13 Sep 2013 08:40:01 +0000 (11:40 +0300)]
Bluetooth: Add synchronization train parameters reading support
This patch adds support for reading the synchronization train parameters
for controllers that support the feature. Since the feature is
detectable through the local features page 2, which is retreived only in
stage 3 of the HCI init sequence, there is no other option than to add a
fourth stage to the init sequence.
For now the patch doesn't yet add storing of the parameters, but it is
nevertheless convenient to have around to see what kind of parameters
various controllers use by default (analyzable e.g. with the btmon user
space tool).
Johan Hedberg [Mon, 16 Sep 2013 10:05:19 +0000 (13:05 +0300)]
Bluetooth: Fix waiting for clearing of BT_SK_SUSPEND flag
In the case of blocking sockets we should not proceed with sendmsg() if
the socket has the BT_SK_SUSPEND flag set. So far the code was only
ensuring that POLLOUT doesn't get set for non-blocking sockets using
poll() but there was no code in place to ensure that blocking sockets do
the right thing when writing to them.
This patch adds a new bt_sock_wait_ready helper function to sleep in the
sendmsg call if the BT_SK_SUSPEND flag is set, and wake up as soon as it
is unset. It also updates the L2CAP and RFCOMM sendmsg callbacks to take
advantage of this new helper function.
Johan Hedberg [Mon, 16 Sep 2013 10:05:18 +0000 (13:05 +0300)]
Bluetooth: Fix responding to invalid L2CAP signaling commands
When we have an LE link we should not respond to any data on the BR/EDR
L2CAP signaling channel (0x0001) and vice-versa when we have a BR/EDR
link we should not respond to LE L2CAP (CID 0x0005) signaling commands.
This patch fixes this issue by checking for a valid link type and
ignores data if it is wrong.
Johan Hedberg [Mon, 16 Sep 2013 10:05:17 +0000 (13:05 +0300)]
Bluetooth: Fix sending responses to identified L2CAP response packets
When L2CAP packets return a non-zero error and the value is passed
onwards by l2cap_bredr_sig_cmd this will trigger a command reject packet
to be sent. However, the core specification (page 1416 in core 4.0) says
the following: "Command Reject packets should not be sent in response to
an identified Response packet.".
This patch ensures that a command reject packet is not sent for any
identified response packet by ignoring the error return value from the
response handler functions.
Johan Hedberg [Mon, 16 Sep 2013 10:05:16 +0000 (13:05 +0300)]
Bluetooth: Fix L2CAP command reject reason
There are several possible reason codes that can be sent in the command
reject L2CAP packet. Before this patch the code has used a hard-coded
single response code ("command not understood"). This patch adds a
helper function to map the return value of an L2CAP handler function to
the correct command reject reason.
Johan Hedberg [Mon, 16 Sep 2013 10:05:15 +0000 (13:05 +0300)]
Bluetooth: Fix L2CAP Disconnect response for unknown CID
If we receive an L2CAP Disconnect Request for an unknown CID we should
not just silently drop it but reply with a proper Command Reject
response. This patch fixes this by ensuring that the disconnect handler
returns a proper error instead of 0 and will cause the function caller
to send the right response.
Johan Hedberg [Mon, 16 Sep 2013 10:05:14 +0000 (13:05 +0300)]
Bluetooth: Fix L2CAP error return used for failed channel lookups
The EFAULT error should only be used for memory address related errors
and ENOENT might be needed for other purposes than invalid CID errors.
This patch fixes the l2cap_config_req, l2cap_connect_create_rsp and
l2cap_create_channel_req handlers to use the unique EBADSLT error to
indicate failed lookups on a given CID.
Johan Hedberg [Mon, 16 Sep 2013 10:05:13 +0000 (13:05 +0300)]
Bluetooth: Fix double error response for l2cap_create_chan_req
When an L2CAP request handler returns non-zero the calling code will
send a command reject response. The l2cap_create_chan_req function will
in some cases send its own response but then still return a -EFAULT
error which would cause two responses to be sent. This patch fixes this
by making the function return 0 after sending its own response.
Johan Hedberg [Mon, 16 Sep 2013 10:05:12 +0000 (13:05 +0300)]
Bluetooth: Remove unused event mask struct
The struct for HCI_Set_Event_Mask is never used. Instead a local 8-byte
array is used for sending this command. Therefore, remove the
unnecessary struct definition.
Johan Hedberg [Fri, 13 Sep 2013 05:58:18 +0000 (08:58 +0300)]
Bluetooth: Fix rfkill functionality during the HCI setup stage
We need to let the setup stage complete cleanly even when the HCI device
is rfkilled. Otherwise the HCI device will stay in an undefined state
and never get notified to user space through mgmt (even when it gets
unblocked through rfkill).
This patch makes sure that hci_dev_open() can be called in the HCI_SETUP
stage, that blocking the device doesn't abort the setup stage, and that
the device gets proper powered down as soon as the setup stage completes
in case it was blocked meanwhile.
The bug that this patch fixed can be very easily reproduced using e.g.
the rfkill command line too. By running "rfkill block all" before
inserting a Bluetooth dongle the resulting HCI device goes into a state
where it is never announced over mgmt, not even when "rfkill unblock all"
is run.
Johan Hedberg [Fri, 13 Sep 2013 05:58:17 +0000 (08:58 +0300)]
Bluetooth: Introduce a new HCI_RFKILLED flag
This makes it more convenient to check for rfkill (no need to check for
dev->rfkill before calling rfkill_blocked()) and also avoids potential
races if the RFKILL state needs to be checked from within the rfkill
callback.
Syam Sidhardhan [Mon, 5 Aug 2013 16:59:12 +0000 (01:59 +0900)]
Bluetooth: Fix ACL alive for long in case of non pariable devices
For certain devices (ex: HID mouse), support for authentication,
pairing and bonding is optional. For such devices, the ACL alive
for too long after the L2CAP disconnection.
To avoid the ACL alive for too long after L2CAP disconnection, reset the
ACL disconnect timeout back to HCI_DISCONN_TIMEOUT during L2CAP connect.
Andre Guedes [Wed, 31 Jul 2013 19:25:29 +0000 (16:25 -0300)]
Bluetooth: Fix encryption key size for peripheral role
This patch fixes the connection encryption key size information when
the host is playing the peripheral role. We should set conn->enc_key_
size in hci_le_ltk_request_evt, otherwise it is left uninitialized.
Andre Guedes [Wed, 31 Jul 2013 19:25:28 +0000 (16:25 -0300)]
Bluetooth: Fix security level for peripheral role
While playing the peripheral role, the host gets a LE Long Term Key
Request Event from the controller when a connection is established
with a bonded device. The host then informs the LTK which should be
used for the connection. Once the link is encrypted, the host gets
an Encryption Change Event.
Therefore we should set conn->pending_sec_level instead of conn->
sec_level in hci_le_ltk_request_evt. This way, conn->sec_level is
properly updated in hci_encrypt_change_evt.
Moreover, since we have a LTK associated to the device, we have at
least BT_SECURITY_MEDIUM security level.
Bluetooth: Only schedule raw queue when user channel is active
When the user channel is set and an user application has full control
over the device, do not bother trying to schedule any queues except
the raw queue.
This is an optimization since with user channel, only the raw queue
is in use.
Bluetooth: Disable upper layer connections when user channel is active
When the device has the user channel flag set, it means it is driven by
an user application. In that case do not allow any connections from
L2CAP or SCO sockets.
This is the same situation as when the device has the raw flag set and
it will then return EHOSTUNREACH.
Bluetooth: Add support creating virtual AMP controllers
So far the only option to create a virtual AMP controller was by
setting a module parameter for the hci_vhci driver. This patch adds
the functionality to define inline to create either a BR/EDR or an
AMP controller.
In addition the client will be informed which HCI controller index
it got assigned. That is especially useful for automated end-to-end
testing.
To keep backwards compatibility with existing userspace, the command
for creating a controller type needs to be send right after opening
the device node. If the command is not send, it defaults back to
automatically creating a BR/EDR controller.
Marcel Holtmann [Tue, 27 Aug 2013 04:40:52 +0000 (21:40 -0700)]
Bluetooth: Introduce new HCI socket channel for user operation
This patch introcuces a new HCI socket channel that allows user
applications to take control over a specific HCI device. The application
gains exclusive access to this device and forces the kernel to stay away
and not manage it. In case of the management interface it will actually
hide the device.
Such operation is useful for security testing tools that need to operate
underneath the Bluetooth stack and need full control over a device. The
advantage here is that the kernel still provides the service of hardware
abstraction and HCI level access. The use of Bluetooth drivers for
hardware access also means that sniffing tools like btmon or hcidump
are still working and the whole set of transaction can be traced with
existing tools.
With the new channel it is possible to send HCI commands, ACL and SCO
data packets and receive HCI events, ACL and SCO packets from the
device. The format follows the well established H:4 protocol.
The new HCI user channel can only be established when a device has been
through its setup routine and is currently powered down. This is
enforced to not cause any problems with current operations. In addition
only one user channel per HCI device is allowed. It is exclusive access
for one user application. Access to this channel is limited to process
with CAP_NET_RAW capability.
Using this new facility does not require any external library or special
ioctl or socket filters. Just create the socket and bind it. After that
the file descriptor is ready to speak H:4 protocol.
The example shows on how to create a user channel for hci0 device. Error
handling has been left out of the example. However with the limitations
mentioned above it is advised to handle errors. Binding of the user
cahnnel socket can fail for various reasons. Specifically if the device
is currently activated by BlueZ or if the access permissions are not
present.
Marcel Holtmann [Tue, 27 Aug 2013 04:40:51 +0000 (21:40 -0700)]
Bluetooth: Introduce user channel flag for HCI devices
This patch introduces a new user channel flag that allows to give full
control of a HCI device to a user application. The kernel will stay away
from the device and does not allow any further modifications of the
device states.
The existing raw flag is not used since it has a bit of unclear meaning
due to its legacy. Using a new flag makes the code clearer.
A device with the user channel flag set can still be enumerate using the
legacy API, but it does not longer enumerate using the new management
interface used by BlueZ 5 and beyond. This is intentional to not confuse
users of modern systems.
Marcel Holtmann [Mon, 26 Aug 2013 16:39:55 +0000 (09:39 -0700)]
Bluetooth: Restrict ioctls to HCI raw channel sockets
The various legacy ioctls used with HCI sockets are limited to raw
channel only. They are not used on the other channels and also have
no meaning there. So return an error if tried to use them.
Marcel Holtmann [Mon, 26 Aug 2013 16:29:39 +0000 (09:29 -0700)]
Bluetooth: Fix error handling for HCI socket options
The HCI sockets for monitor and control do not support any HCI specific
socket options and if tried, an error will be returned. However the
error used is EINVAL and that is not really descriptive. To make it
clear that these sockets are not handling HCI socket options, return
EBADFD instead.
Marcel Holtmann [Mon, 26 Aug 2013 07:06:30 +0000 (00:06 -0700)]
Bluetooth: Fix handling of getpeername() for HCI sockets
The HCI sockets do not have a peer associated with it and so make sure
that getpeername() returns EOPNOTSUPP since this operation is actually
not supported on HCI sockets.
Marcel Holtmann [Mon, 26 Aug 2013 06:25:15 +0000 (23:25 -0700)]
Bluetooth: Refactor raw socket filter into more readable code
The handling of the raw socket filter is rather obscure code and it gets
in the way of future extensions. Instead of inline filtering in the raw
socket packet routine, refactor it into its own function.
make Maxim machine freeze when try to start wireless device.
Initialization order and sending MCU_BOOT_SIGNAL request, changed in
above commit, is important. Doing things incorrectly make PCIe bus
problems, which can froze the machine.
This patch change initialization sequence like vendor driver do:
function NICInitializeAsic() from
2011_1007_RT5390_RT5392_Linux_STA_V2.5.0.3_DPO (PCI devices) and
DPO_RT5572_LinuxSTA_2.6.1.3_20121022 (according Mediatek, latest driver
for RT8070/RT3070/RT3370/RT3572/RT5370/RT5372/RT5572 USB devices).
It fixes freezes on Maxim system.
On most 64 Bit systems unsigned long is 64 bit long and then -MAX_ERRNO
is out of the range of a u32 used to store the error code in.
This patch casts the -MAX_ERRNO to a u32 instead.
This fixes a regression introduced in:
commit fd4edf197544bae1c77d84bad354aa7ce1d08ce1
Author: Hauke Mehrtens <hauke@hauke-m.de>
Date: Mon Jul 15 13:15:08 2013 +0200
bcma: fix handling of big addrl
Reported-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Tested-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
rtl8187: fix use after free on failure path in rtl8187_init_urbs()
In case of __dev_alloc_skb() failure rtl8187_init_urbs()
calls usb_free_urb(entry) where 'entry' can points to urb
allocated at the previous iteration. That means refcnt will be
decremented incorrectly and the urb can be used after memory
deallocation.
The patch fixes the issue and implements error handling of init_urbs
in rtl8187_start().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The kernel configuration for the driver could result in
compilation issues as reported by Randy Dunlap. His results
are show below:
"on x86_64:
when
CONFIG_MMC=m
CONFIG_BRCMUTIL=y
CONFIG_BRCMFMAC=y
CONFIG_BRCMFMAC_SDIO=y
This bool kconfig symbol:
config BRCMFMAC_SDIO
bool "SDIO bus interface support for FullMAC driver"
depends on MMC
allows BRCMFMAC_SDIO to be y even when MMC=m.
Is there a reasonable solution to this?
This causes many build errors:
drivers/built-in.o: In function `brcmf_sdio_assert_info':
dhd_sdio.c:(.text+0x39609b): undefined reference to `sdio_claim_host'
dhd_sdio.c:(.text+0x3960d9): undefined reference to `sdio_release_host'
drivers/built-in.o: In function `brcmf_sdio_readframes':
dhd_sdio.c:(.text+0x396a62): undefined reference to `sdio_claim_host'
dhd_sdio.c:(.text+0x396a9b): undefined reference to `sdio_release_host'
..."
This patch adds the appropriate logic in Kconfig to resolve
these issues. The solution was provided by Hauke Mehrtens.
Reported-by: Randy Dunlap <rdunlap@infradead.org> Cc: Hauke Mehrtens <hauke@hauke-m.de> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Acked-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Solomon Peachy [Wed, 28 Aug 2013 00:29:47 +0000 (20:29 -0400)]
cw1200: Prevent a lock-related hang in the cw1200_spi driver
The cw1200_spi driver tries to mirror the cw1200_sdio driver's lock
API, which relies on sdio_claim_host/sdio_release_host to serialize
hardware operations across multiple threads.
Unfortunately the implementation was flawed, as it lacked a way to wake
up the lock requestor when there was contention, often resulting in a
hang.
This problem was uncovered while trying to fix the
spi-transfers-in-interrupt-context BUG() corrected in the previous
patch. Many thanks to Dave Sizeburns for his assistance in fixing this.
Signed-off-by: Solomon Peachy <pizza@shaftnet.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Solomon Peachy [Wed, 28 Aug 2013 00:29:46 +0000 (20:29 -0400)]
cw1200: Don't perform SPI transfers in interrupt context
When we get an interrupt from the hardware, the first thing the driver does
is tell the device to mask off the interrupt line. Unfortunately this
involves a SPI transaction in interrupt context. Some (most?) SPI
controllers perform the transfer asynchronously and try to sleep.
This is bad, and triggers a BUG().
So, work around this by using adding a hwbus hook for the cw1200 driver
core to call. The cw1200_spi driver translates this into
irq_disable()/irq_enable() calls instead, which can safely be called in
interrupt context.
Apparently the platforms I used to develop the cw1200_spi driver used
synchronous spi_sync() implementations, which is why this didn't surface
until now.
Many thanks to Dave Sizeburns for the inital bug report and his services
as a tester.
Signed-off-by: Solomon Peachy <pizza@shaftnet.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The only actual current lockref user (dcache) uses zero reference counts
even for perfectly live dentries, because it's a cache: there may not be
any users, but that doesn't mean that we want to throw away the dentry.
At the same time, the dentry cache does have a notion of a truly "dead"
dentry that we must not even increment the reference count of, because
we have pruned it and it is not valid.
Currently that distinction is not visible in the lockref itself, and the
dentry cache validation uses "lockref_get_or_lock()" to either get a new
reference to a dentry that already had existing references (and thus
cannot be dead), or get the dentry lock so that we can then verify the
dentry and increment the reference count under the lock if that
verification was successful.
That's all somewhat complicated.
This adds the concept of being "dead" to the lockref itself, by simply
using a count that is negative. This allows a usage scenario where we
can increment the refcount of a dentry without having to validate it,
and pushing the special "we killed it" case into the lockref code.
The dentry code itself doesn't actually use this yet, and it's probably
too late in the merge window to do that code (the dentry_kill() code
with its "should I decrement the count" logic really is pretty complex
code), but let's introduce the concept at the lockref level now.
The code got rewritten, but the comments got copied as-is from older
versions, and as a result the argument name in the comment didn't
actually match the code any more.
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs pile 2 (of many) from Al Viro:
"Mostly Miklos' series this time"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
constify dcache.c inlined helpers where possible
fuse: drop dentry on failed revalidate
fuse: clean up return in fuse_dentry_revalidate()
fuse: use d_materialise_unique()
sysfs: use check_submounts_and_drop()
nfs: use check_submounts_and_drop()
gfs2: use check_submounts_and_drop()
afs: use check_submounts_and_drop()
vfs: check unlinked ancestors before mount
vfs: check submounts and drop atomically
vfs: add d_walk()
vfs: restructure d_genocide()
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull namespace changes from Eric Biederman:
"This is an assorted mishmash of small cleanups, enhancements and bug
fixes.
The major theme is user namespace mount restrictions. nsown_capable
is killed as it encourages not thinking about details that need to be
considered. A very hard to hit pid namespace exiting bug was finally
tracked and fixed. A couple of cleanups to the basic namespace
infrastructure.
Finally there is an enhancement that makes per user namespace
capabilities usable as capabilities, and an enhancement that allows
the per userns root to nice other processes in the user namespace"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
userns: Kill nsown_capable it makes the wrong thing easy
capabilities: allow nice if we are privileged
pidns: Don't have unshare(CLONE_NEWPID) imply CLONE_THREAD
userns: Allow PR_CAPBSET_DROP in a user namespace.
namespaces: Simplify copy_namespaces so it is clear what is going on.
pidns: Fix hang in zap_pid_ns_processes by sending a potentially extra wakeup
sysfs: Restrict mounting sysfs
userns: Better restrictions on when proc and sysfs can be mounted
vfs: Don't copy mount bind mounts of /proc/<pid>/ns/mnt between namespaces
kernel/nsproxy.c: Improving a snippet of code.
proc: Restrict mounting the proc filesystem
vfs: Lock in place mounts from more privileged users
Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull security subsystem updates from James Morris:
"Nothing major for this kernel, just maintenance updates"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (21 commits)
apparmor: add the ability to report a sha1 hash of loaded policy
apparmor: export set of capabilities supported by the apparmor module
apparmor: add the profile introspection file to interface
apparmor: add an optional profile attachment string for profiles
apparmor: add interface files for profiles and namespaces
apparmor: allow setting any profile into the unconfined state
apparmor: make free_profile available outside of policy.c
apparmor: rework namespace free path
apparmor: update how unconfined is handled
apparmor: change how profile replacement update is done
apparmor: convert profile lists to RCU based locking
apparmor: provide base for multiple profiles to be replaced at once
apparmor: add a features/policy dir to interface
apparmor: enable users to query whether apparmor is enabled
apparmor: remove minimum size check for vmalloc()
Smack: parse multiple rules per write to load2, up to PAGE_SIZE-1 bytes
Smack: network label match fix
security: smack: add a hash table to quicken smk_find_entry()
security: smack: fix memleak in smk_write_rules_list()
xattr: Constify ->name member of "struct xattr".
...
Pull crypto update from Herbert Xu:
"Here is the crypto update for 3.12:
- Added MODULE_SOFTDEP to allow pre-loading of modules.
- Reinstated crct10dif driver using the module softdep feature.
- Allow via rng driver to be auto-loaded.
- Split large input data when necessary in nx.
- Handle zero length messages correctly for GCM/XCBC in nx.
- Handle SHA-2 chunks bigger than block size properly in nx.
Pull networking fixes from David Miller:
"A quick set of fixes, some to deal with fallout from yesterday's
net-next merge.
1) Fix compilation of bnx2x driver with CONFIG_BNX2X_SRIOV disabled,
from Dmitry Kravkov.
2) Fix a bnx2x regression caused by one of Dave Jones's mistaken
braces changes, from Eilon Greenstein.
3) Add some protective filtering in the netlink tap code, from Daniel
Borkmann.
4) Fix TCP congestion window growth regression after timeouts, from
Yuchung Cheng.
5) Correctly adjust TCP's rcv_ssthresh for out of order packets, from
Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
tcp: properly increase rcv_ssthresh for ofo packets
net: add documentation for BQL helpers
mlx5: remove unused MLX5_DEBUG param in Kconfig
bnx2x: Restore a call to config_init
bnx2x: fix broken compilation with CONFIG_BNX2X_SRIOV is not set
tcp: fix no cwnd growth after timeout
net: netlink: filter particular protocols from analyzers
Merge tag 'gpio-v3.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v3.12 series:
- A new driver for the TZ1090 PDC which is used on the metag
architecture.
- A new driver for the Kontron ETX or COMexpress GPIO block. This is
found on some ETX x86 devices.
- A new driver for the Fintek Super-I/O chips, used on some x86
boards.
- Added device tree probing on a few select GPIO blocks.
- Drop the Exynos support from the Samsung GPIO driver.
The Samsung maintainers have moved over to use the modernized pin
control driver to provide GPIO for the modern platforms instead.
- The usual bunch of non-critical fixes and cleanups"
* tag 'gpio-v3.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (36 commits)
gpio: return -ENOTSUPP if debounce cannot be set
gpio: improve error path in gpiolib
gpio: add GPIO support for F71882FG and F71889F
of: add vendor prefix for Microchip Technology Inc
gpio: mcp23s08: rename the device tree property
gpio: samsung: Drop support for Exynos SoCs
gpio: pcf857x: Remove pdata argument to pcf857x_irq_domain_init()
gpio: pcf857x: Sort headers alphabetically
gpio: max7301: Reverting "Do not force SPI speed when using OF Platform"
gpio: Fix bit masking in Kontron PLD GPIO driver
gpio: pca953x: fix gpio input on gpio offsets >= 8
drivers/gpio: simplify use of devm_ioremap_resource
drivers/gpio/gpio-omap.c: convert comma to semicolon
gpio-lynxpoint: Fix warning about unbalanced pm_runtime_enable
gpio: Fix platform driver name in Kontron PLD GPIO driver
gpio: adnp: Fix segfault if request_threaded_irq fails
gpio: msm: Staticize local variable 'msm_gpio'
gpio: gpiolib-of.c: make error message more meaningful by adding the node name and index
gpio: use dev_get_platdata()
gpio/mxc: add chained_irq_enter/exit() to mx2_gpio_irq_handler
...
Revert "Input: introduce BTN/ABS bits for drums and guitars"
This reverts commits 61e00655e9cb, 73f8645db191 and 8e22ecb603c8:
"Input: introduce BTN/ABS bits for drums and guitars"
"HID: wiimote: add support for Guitar-Hero drums"
"HID: wiimote: add support for Guitar-Hero guitars"
The extra new ABS_xx values resulted in ABS_MAX no longer being a
power-of-two, which broke the comparison logic. It also caused the
ioctl numbers to overflow into the next byte, causing problems for that.
We'll try again for 3.13.
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de> Reported-by: Linus Torvalds <torvalds@linux-foundation.org> Acked-by: David Herrmann <dh.herrmann@gmail.com> Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: Benjamin Tissoires <benjamin.tissoires@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC board updates from Olof Johansson:
"Board updates for 3.12. Again, a bit of domain overlap with SoC and
DT branches, but most of this is around legacy code and board support.
We've found that platform maintainers have a hard time separating all
of these out and might move towards fewer branches for next release.
- Removal of a number of Marvell Kirkwood board files, since contents
is now common and mostly configured via DT.
- Device-tree updates for Marvell Dove, including irqchip and
clocksource setup.
- Defconfig updates. Gotta go somewhere. One new one for Renesas
Lager.
- New backlight drivers for backlights used on Renesas shmobile
platforms.
- Removal of Renesas leds driver.
- Shuffling of some of the new Broadcom platforms to give room for
others in the same mach directory. More in 3.13"
* tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (67 commits)
mmc: sdhci-bcm-kona: Staticize sdhci_bcm_kona_card_event
mmc: sdhci-bcm-kona: Remove unneeded version.h inclusion
ARM: bcm: Make secure API call optional
ARM: DT: binding fixup to align with vendor-prefixes.txt (drivers)
ARM: mmc: fix NONREMOVABLE test in sdhci-bcm-kona
ARM: bcm: Rename board_bcm
mmc: sdhci-bcm-kona: make linker-section warning go away
ARM: tegra: defconfig updates
ARM: dove: add initial DT file for Globalscale D2Plug
ARM: dove: add GPIO IR receiver node to SolidRun CuBox
ARM: dove: add common pinmux functions to DT
ARM: dove: add cpu device tree node
ARM: dove: update dove_defconfig with SI5351, PCI, and xHCI
arch/arm/mach-kirkwood: Avoid using ARRAY_AND_SIZE(e) as a function argument
ARM: kirkwood: fix DT building and update defconfig
ARM: kirkwood: Remove all remaining trace of DNS-320/325 platform code
ARM: configs: disable DEBUG_LL in bcm_defconfig
ARM: bcm281xx: Board specific reboot code
ARM bcm281xx: Turn on socket & network support.
ARM: bcm281xx: Turn on L2 cache.
...
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"This branch contains mostly additions and changes to platform
enablement and SoC-level drivers. Since there's sometimes a
dependency on device-tree changes, there's also a fair amount of
those in this branch.
Pieces worth mentioning are:
- Mbus driver for Marvell platforms, allowing kernel configuration
and resource allocation of on-chip peripherals.
- Enablement of the mbus infrastructure from Marvell PCI-e drivers.
- Preparation of MSI support for Marvell platforms.
- Addition of new PCI-e host controller driver for Tegra platforms
- Some churn caused by sharing of macro names between i.MX 6Q and 6DL
platforms in the device tree sources and header files.
- Various suspend/PM updates for Tegra, including LP1 support.
- Versatile Express support for MCPM, part of big little support.
- Allwinner platform support for A20 and A31 SoCs (dual and quad
Cortex-A7)
- OMAP2+ support for DRA7, a new Cortex-A15-based SoC.
The code that touches other architectures are patches moving MSI
arch-specific functions over to weak symbols and removal of
ARCH_SUPPORTS_MSI, acked by PCI maintainers"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (266 commits)
tegra-cpuidle: provide stub when !CONFIG_CPU_IDLE
PCI: tegra: replace devm_request_and_ioremap by devm_ioremap_resource
ARM: tegra: Drop ARCH_SUPPORTS_MSI and sort list
ARM: dts: vf610-twr: enable i2c0 device
ARM: dts: i.MX51: Add one more I2C2 pinmux entry
ARM: dts: i.MX51: Move pins configuration under "iomuxc" label
ARM: dtsi: imx6qdl-sabresd: Add USB OTG vbus pin to pinctrl_hog
ARM: dtsi: imx6qdl-sabresd: Add USB host 1 VBUS regulator
ARM: dts: imx27-phytec-phycore-som: Enable AUDMUX
ARM: dts: i.MX27: Disable AUDMUX in the template
ARM: dts: wandboard: Add support for SDIO bcm4329
ARM: i.MX5 clocks: Remove optional clock setup (CKIH1) from i.MX51 template
ARM: dts: imx53-qsb: Make USBH1 functional
ARM i.MX6Q: dts: Enable I2C1 with EEPROM and PMIC on Phytec phyFLEX-i.MX6 Ouad module
ARM i.MX6Q: dts: Enable SPI NOR flash on Phytec phyFLEX-i.MX6 Ouad module
ARM: dts: imx6qdl-sabresd: Add touchscreen support
ARM: imx: add ocram clock for imx53
ARM: dts: imx: ocram size is different between imx6q and imx6dl
ARM: dts: imx27-phytec-phycore-som: Fix regulator settings
ARM: dts: i.MX27: Remove clock name from CPU node
...
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"Device tree and bindings updates for 3.12.
General additions of various on-chip and on-board peripherals on
various platforms as support gets added. Some of the bigger changes
are:
- Addition of (new) PCI-e support on Tegra.
- More Tegra4 support, including PMC configuration for Dalmore.
- Addition of a new board for Exynos4 (trats2) and more bindings for
4x12 IP.
- Addition of Allwinner A20 and A31 SoC and board files.
- Move of the ST Ericsson device tree files to now use ste-* prefix.
- More move of hardware description of shmobile platforms to DT.
- Two new board dts files for Freescale MXs"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (177 commits)
dts: Rename DW APB timer compatible strings
dts: Deprecate ALTR as a vendor prefix
of: add vendor prefix for Altera Corp.
ARM: at91/dt: sam9x5ek: add sound configuration
ARM: at91/dt: sam9x5ek: enable SSC
ARM: at91/dt: sam9x5ek: add WM8731 codec
ARM: at91/dt: sam9x5: add SSC DMA parameters
ARM: at91/dt: add at91rm9200 PQFP package version
ARM: at91: at91rm9200: set default mmc0 pinctrl-names
ARM: at91: at91sam9n12: correct pin number of gpio-key
ARM: at91: at91sam9n12: add qt1070 support
ARM: at91: at91sam9n12: add pinctrl of TWI
ARM: at91: Add PMU support for sama5d3
ARM: at91: at91sam9260: add missing pinctrl-names on mmc
ARM: tegra: configure power off for Dalmore
ARM: DT: binding fixup to align with vendor-prefixes.txt (DT)
ARM: dts: add sdio blocks to bcm28155-ap board
ARM: dts: align sdio numbers to HW definition
ARM: sun7i: Add Olimex A20-Olinuxino-Micro support
ARM: sun7i: Add Allwinner A20 DTSI
...
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This branch contains code cleanups, moves and removals for 3.12.
There's a large number of various cleanups, and a nice net removal of
13500 lines of code.
Highlights worth mentioning are:
- A series of patches from Stephen Boyd removing the ARM local timer
API.
- Move of Qualcomm MSM IOMMU code to drivers/iommu.
- Samsung PWM driver cleanups from Tomasz Figa, removing legacy PWM
driver and switching over to the drivers/pwm one.
- Removal of some unusued auto-generated headers for OMAP2+ (PRM/CM).
There's also a move of a header file out of include/linux/i2c/ to
platform_data, where it really belongs. It touches mostly ARM
platform code for include changes so we took it through our tree"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: OMAP2+: Add back the define for AM33XX_RST_GLOBAL_WARM_SW_MASK
gpio: (gpio-pca953x) move header to linux/platform_data/
arm: zynq: hotplug: Remove unreachable code
ARM: SAMSUNG: Remove unnecessary exynos4_default_sdhci*()
tegra: simplify use of devm_ioremap_resource
ARM: SAMSUNG: Remove plat/regs-timer.h header
ARM: SAMSUNG: Remove remaining uses of plat/regs-timer.h header
ARM: SAMSUNG: Remove pwm-clock infrastructure
ARM: SAMSUNG: Remove old PWM timer platform devices
pwm: Remove superseded pwm-samsung-legacy driver
ARM: SAMSUNG: Modify board files to use new PWM platform device
ARM: SAMSUNG: Rework private data handling in dev-backlight
pwm: Add new pwm-samsung driver
ARM: mach-mvebu: remove redundant DT parsing and validation
ARM: msm: Only compile io.c on platforms that use it
iommu/msm: Move mach includes to iommu directory
ARM: msm: Remove devices-iommu.c
ARM: msm: Move mach/board.h contents to common.h
ARM: msm: Migrate msm_timer to CLOCKSOURCE_OF_DECLARE
ARM: msm: Remove TMR and TMR0 static mappings
...
Merge tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC low-priority fixes from Olof Johansson:
"This branch contains a handful of fixes for various platforms that
weren't serious enough to be included in late 3.11-rc releases. Most
of them are for minor cleanups and cosmetic fixes.
There's also a bit of code removal here, one board file removal for
clps711x, and removal of some legacy device creation on OMAP2+"
* tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (25 commits)
ARM: OMAP2: use 'int' instead of 'unsigned' for variable 'gpmc_irq_start'
ARM: OMAP2: remove useless variable 'ret'
ARM: OMAP: dma: fix error return code in omap_system_dma_probe()
ARM: OMAP2+: fix wrong address when loading PRM_FRAC_INCREMENTOR_DENUMERATOR_RELOAD
ARM: OMAP2+: am33xx-restart: trigger warm reset on omap2+ boards
ARM: OMAP2: Use a consistent AM33XX SoC option description
ARM: OMAP2+: Remove legacy device creation for McPDM and DMIC
ARM: clps711x: edb7211: Remove extra iotable_init() call
ARM: clps711x: autcpu12: Remove incorrect config checking
ARM: clps711x: Drop fortunet board support
ARM: clps711x: Remove the special name for the syscon driver
ARM: dts: Fix memory node in skeleton64.dtsi
ARM: Keystone: Convert device tree file to use IRQ defines
ARM: keystone: use #include to include skeleton.dtsi
ARM: keystone: Drop the un-necessary dsb from keystone_cpu_smc()
ARM: Keystone: No need to preserve r12 across smc call
ARM: keystone: remove redundant smp_init_cpus definition
ARM: keystone: drop useless HAVE_SCHED_CLOCK
ARM: dove: fix missing __init section of dove_mpp_gpio_mode
ARM: shmobile: armadillo800eva-reference: fix compiler warning
...
Merge tag 'please-pull-misc-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux
Pull ia64 fixes from Tony Luck:
"Couple of small cleanups for ia64"
* tag 'please-pull-misc-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
[IA64] Use asm-generic/bitops/builtin-ffs.h
[IA64] dmi.h: Make dmi_alloc use kzalloc
Eric Dumazet [Fri, 6 Sep 2013 17:35:58 +0000 (10:35 -0700)]
tcp: properly increase rcv_ssthresh for ofo packets
TCP receive window handling is multi staged.
A socket has a memory budget, static or dynamic, in sk_rcvbuf.
Because we do not really know how this memory budget translates to
a TCP window (payload), TCP announces a small initial window
(about 20 MSS).
When a packet is received, we increase TCP rcv_win depending
on the payload/truesize ratio of this packet. Good citizen
packets give a hint that it's reasonable to have rcv_win = sk_rcvbuf/2
This heuristic takes place in tcp_grow_window()
Problem is : We currently call tcp_grow_window() only for in-order
packets.
This means that reorders or packet losses stop proper grow of
rcv_win, and senders are unable to benefit from fast recovery,
or proper reordering level detection.
Really, a packet being stored in OFO queue is not a bad citizen.
It should be part of the game as in-order packets.
In our traces, we very often see sender is limited by linux small
receive windows, even if linux hosts use autotuning (DRS) and should
allow rcv_win to grow to ~3MB.
Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Provide a kernel-doc comment documentation for the BQL helpers:
- netdev_sent_queue
- netdev_completed_queue
- netdev_reset_queue
Similarly to how it is done for the other functions, the documentation
only covers the function operating on struct net_device and not struct
netdev_queue.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch proposes to remove the MLX5_DEBUG kernel configuration
parameter defined in drivers/net/ethernet/mellanox/mlx5/core/Kconfig,
but used nowhere in the makefiles and source code.
This could also be fixed by using this parameter,
but this may be a leftover from driver development...
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c0a77ec74f295013d7ba3204dd3ed25fccf83cb4 'bnx2x: Add missing braces in
bnx2x:bnx2x_link_initialize' identified indentation problem, but resolved it
by adding braces instead of fixing the indentation. The braces now prevents a
config_init call in some cases, though it should be called regardless of that
condition. This patch removes the braces and fix the confusing indentation
that caused this mess.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com> CC: Dave Jones <davej@redhat.com> Tested-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Reported-by: Eric Dumazet <eric.dumazet@gmail.com> CC: Ariel Elior <ariele@broadcom.com> Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 0f7cc9a3 "tcp: increase throughput when reordering is high",
it only allows cwnd to increase in Open state. This mistakenly disables
slow start after timeout (CA_Loss). Moreover cwnd won't grow if the
state moves from Disorder to Open later in tcp_fastretrans_alert().
Therefore the correct logic should be to allow cwnd to grow as long
as the data is received in order in Open, Loss, or even Disorder state.
Signed-off-by: Yuchung Cheng <ycheng@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Thu, 5 Sep 2013 15:48:47 +0000 (17:48 +0200)]
net: netlink: filter particular protocols from analyzers
Fix finer-grained control and let only a whitelist of allowed netlink
protocols pass, in our case related to networking. If later on, other
subsystems decide they want to add their protocol as well to the list
of allowed protocols they shall simply add it. While at it, we also
need to tell what protocol is in use otherwise BPF_S_ANC_PROTOCOL can
not pick it up (as it's not filled out).
Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pull Tile arch updates from Chris Metcalf:
"These changes bring in a bunch of new functionality that has been
maintained internally at Tilera over the last year, plus other stray
bits of work that I've taken into the tile tree from other folks.
The changes include some PCI root complex work, interrupt-driven
console support, support for performing fast-path unaligned data
fixups by kernel-based JIT code generation, CONFIG_PREEMPT support,
vDSO support for gettimeofday(), a serial driver for the tilegx
on-chip UART, KGDB support, more optimized string routines, support
for ftrace and kprobes, improved ASLR, and many bug fixes.
We also remove support for the old TILE64 chip, which is no longer
buildable"
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile: (85 commits)
tile: refresh tile defconfig files
tile: rework <asm/cmpxchg.h>
tile PCI RC: make default consistent DMA mask 32-bit
tile: add null check for kzalloc in tile/kernel/setup.c
tile: make __write_once a synonym for __read_mostly
tile: remove support for TILE64
tile: use asm-generic/bitops/builtin-*.h
tile: eliminate no-op "noatomichash" boot argument
tile: use standard tile_bundle_bits type in traps.c
tile: simplify code referencing hypervisor API addresses
tile: change <asm/system.h> to <asm/switch_to.h> in comments
tile: mark pcibios_init() as __init
tile: check for correct compiler earlier in asm-offsets.c
tile: use standard 'generic-y' model for <asm/hw_irq.h>
tile: use asm-generic version of <asm/local64.h>
tile PCI RC: add comment about "PCI hole" problem
tile: remove DEBUG_EXTRA_FLAGS kernel config option
tile: add virt_to_kpte() API and clean up and document behavior
tile: support FRAME_POINTER
tile: support reporting Tilera hypervisor statistics
...
Merge tag 'arm64-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64
Pull ARM64 update from Catalin Marinas:
- User tagged pointers support (top 8-bit of user pointers
automatically ignored by the CPU).
- Kernel mode NEON (no users for arm64 yet but work in progress).
- arm64 kernel Image header extended to accommodate future EFI stub.
- Remove BogoMIPS reporting (not relevant, it's just the timer
frequency).
- Clean-up (EM_AARCH64/EM_ARM to elf-em.h, ELF notes in read-only
segment, unused variable).
- Bug-fixes (RAM boundaries not 2MB aligned, perf, includes).
* tag 'arm64-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
Documentation/arm64: clarify requirements for DTB placement
arm64: mm: permit use of tagged pointers at EL0
Move the EM_ARM and EM_AARCH64 definitions to uapi/linux/elf-em.h
arm64: Remove unused cpu_name ascii in arch/arm64/mm/proc.S
arm64: delay: don't bother reporting bogomips in /proc/cpuinfo
arm64: Fix mapping of memory banks not ending on a PMD_SIZE boundary
arm64: move elf notes into readonly segment
arm64: Enable interrupts in the EL0 undef handler
arm64: Expand arm64 image header
ARM64: include: asm: include "asm/types.h" in "pgtable-2level-types.h" and "pgtable-3level-types.h"
arm64: add support for kernel mode NEON
arm64: perf: fix ARMv8 EVTYPE_MASK to include NSH bit
arm64: perf: fix group validation when using enable_on_exec
Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc updates from Ben Herrenschmidt:
"Here's the powerpc batch for this merge window. Some of the
highlights are:
- A bunch of endian fixes ! We don't have full LE support yet in that
release but this contains a lot of fixes all over arch/powerpc to
use the proper accessors, call the firmware with the right endian
mode, etc...
- A few updates to our "powernv" platform (non-virtualized, the one
to run KVM on), among other, support for bridging the P8 LPC bus
for UARTs, support and some EEH fixes.
- Some mpc51xx clock API cleanups in preparation for a clock API
overhaul
- A pile of cleanups of our old math emulation code, including better
support for using it to emulate optional FP instructions on
embedded chips that otherwise have a HW FPU.
- Some infrastructure in selftest, for powerpc now, but could be
generalized, initially used by some tests for our perf instruction
counting code.
- A pile of fixes for hotplug on pseries (that was seriously
bitrotting)
- The usual slew of freescale embedded updates, new boards, 64-bit
hiberation support, e6500 core PMU support, etc..."
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (146 commits)
powerpc: Correct FSCR bit definitions
powerpc/xmon: Fix printing of set of CPUs in xmon
powerpc/pseries: Move lparcfg.c to platforms/pseries
powerpc/powernv: Return secondary CPUs to firmware on kexec
powerpc/btext: Fix CONFIG_PPC_EARLY_DEBUG_BOOTX on ppc32
powerpc: Cleanup handling of the DSCR bit in the FSCR register
powerpc/pseries: Child nodes are not detached by dlpar_detach_node
powerpc/pseries: Add mising of_node_put in delete_dt_node
powerpc/pseries: Make dlpar_configure_connector parent node aware
powerpc/pseries: Do all node initialization in dlpar_parse_cc_node
powerpc/pseries: Fix parsing of initial node path in update_dt_node
powerpc/pseries: Pack update_props_workarea to map correctly to rtas buffer header
powerpc/pseries: Fix over writing of rtas return code in update_dt_node
powerpc/pseries: Fix creation of loop in device node property list
powerpc: Skip emulating & leave interrupts off for kernel program checks
powerpc: Add more exception trampolines for hypervisor exceptions
powerpc: Fix location and rename exception trampolines
powerpc: Add more trap names to xmon
powerpc/pseries: Add a warning in the case of cross-cpu VPA registration
powerpc: Update the 00-Index in Documentation/powerpc
...
Chris Metcalf [Fri, 6 Sep 2013 12:58:35 +0000 (08:58 -0400)]
tile: refresh tile defconfig files
These are based on the current shipping versions of the config files
from Tilera, as synced up to the tip, so are a better starting point
for folks who want a default configuration.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Chris Metcalf [Fri, 6 Sep 2013 12:56:45 +0000 (08:56 -0400)]
tile: rework <asm/cmpxchg.h>
The macrology in cmpxchg.h was designed to allow arbitrary pointer
and integer values to be passed through the routines. To support
cmpxchg() on 64-bit values on the 32-bit tilepro architecture, we
used the idiom "(typeof(val))(typeof(val-val))". This way, in the
"size 8" branch of the switch, when the underlying cmpxchg routine
returns a 64-bit quantity, we cast it first to a typeof(val-val)
quantity (i.e. size_t if "val" is a pointer) with no warnings about
casting between pointers and integers of different sizes, then cast
onwards to typeof(val), again with no warnings. If val is not a
pointer type, the additional cast is a no-op. We can't replace the
typeof(val-val) cast with (for example) unsigned long, since then if
"val" is really a 64-bit type, we cast away the high bits.
HOWEVER, this fails with current gcc (through 4.7 at least) if "val"
is a pointer to an incomplete type. Unfortunately gcc isn't smart
enough to realize that "val - val" will always be a size_t type
even if it's an incomplete type pointer.
Accordingly, I've reworked the way we handle the casting. We have
given up the ability to use cmpxchg() on 64-bit values on tilepro,
which is OK in the kernel since we should use cmpxchg64() explicitly
on such values anyway. As a result, I can just use simple "unsigned
long" casts internally.
As I reworked it, I realized it would be cleaner to move the
architecture-specific conditionals for cmpxchg and xchg out of the
atomic.h headers and into cmpxchg, and then use the cmpxchg() and
xchg() primitives directly in atomic.h and elsewhere. This allowed
the cmpxchg.h header to stand on its own without relying on the
implicit include of it that is performed by <asm/atomic.h>.
It also allowed collapsing the atomic_xchg/atomic_cmpxchg routines
from atomic_{32,64}.h into atomic.h.
I improved the tests that guard the allowed size of the arguments
to the routines to use a __compiletime_error() test. (By avoiding
the use of BUILD_BUG, I could include cmpxchg.h into bitops.h as
well and use the macros there, which is otherwise impossible due
to include order dependency issues.)
The tilepro _atomic_xxx internal methods were previously set up to
take atomic_t and atomic64_t arguments, which isn't as convenient
with the new model, so I modified them to take int or u64 arguments,
which is consistent with how they used the arguments internally
anyway, so provided some nice simplification there too.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID updates from Jiri Kosina:
"Highlights:
- conversion of HID subsystem to use devm-based resource management,
from Benjamin Tissoires
- i2c-hid support for DT bindings, from Benjamin Tissoires
- much improved support for Win8-multitouch devices, from Benjamin
Tissoires
- cleanup of core code using common hidinput_input_event(), from
David Herrmann
- fix for bug in implement() access to the bit stream (causing oops)
that has been present in the code for ages, but devices that are
able to trigger it have started to appear only now, from Jiri
Kosina
- fixes for CVE-2013-2899, CVE-2013-2898, CVE-2013-2896,
CVE-2013-2892, CVE-2013-2888 (all triggerable only by specially
crafted malicious HW devices plugged into the system), from Kees
Cook
- hidraw oops fix, from Manoj Chourasia
- various smaller fixes here and there, support for a bunch of new
devices by various contributors"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (53 commits)
HID: MAINTAINERS: add roccat drivers
HID: hid-sensor-hub: change kmalloc + memcpy by kmemdup
HID: hid-sensor-hub: move to devm_kzalloc
HID: hid-sensor-hub: fix indentation accross the code
HID: move HID_REPORT_TYPES closer to the report-definitions
HID: check for NULL field when setting values
HID: picolcd_core: validate output report details
HID: sensor-hub: validate feature report details
HID: ntrig: validate feature report details
HID: pantherlord: validate output report details
HID: hid-wiimote: print small buffers via %*phC
HID: uhid: improve uhid example client
HID: Correct the USB IDs for the new Macbook Air 6
HID: wiimote: add support for Guitar-Hero guitars
HID: wiimote: add support for Guitar-Hero drums
Input: introduce BTN/ABS bits for drums and guitars
HID: battery: don't do DMA from stack
HID: roccat: add support for KonePureOptical v2
HID: picolcd: Prevent NULL pointer dereference on _remove()
HID: usbhid: quirk for N-Trig DuoSense Touch Screen
...
Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
Pull ext3, reiserfs, udf & isofs fixes from Jan Kara:
"The contains a bunch of ext3 cleanups and minor improvements, major
reiserfs locking changes which should hopefully fix deadlocks
introduced by BKL removal, and udf/isofs changes to refuse mounting fs
rw instead of mounting it ro automatically which makes eject button
work as expected for all media (see the changelog for why userspace
should be ok with this change)"
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
jbd: use a single printk for jbd_debug()
reiserfs: locking, release lock around quota operations
reiserfs: locking, handle nested locks properly
reiserfs: locking, push write lock out of xattr code
jbd: relocate assert after state lock in journal_commit_transaction()
udf: Refuse RW mount of the filesystem instead of making it RO
udf: Standardize return values in mount sequence
isofs: Refuse RW mount of the filesystem instead of making it RO
ext3: allow specifying external journal by pathname mount option
jbd: remove unneeded semicolon
Merge tag 'for-f2fs-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs
Pull f2fs updates from Jaegeuk Kim:
"This patch-set includes the following major enhancement patches:
- support inline xattrs
- add sysfs support to control GCs explicitly
- add proc entry to show the current segment usage information
- improve the GC/SSR performance
The other bug fixes are as follows:
- avoid the overflow on status calculation
- fix some error handling routines
- fix inconsistent xattr states after power-off-recovery
- fix incorrect xattr node offset definition
- fix deadlock condition in fsync
- fix the fdatasync routine for power-off-recovery"
* tag 'for-f2fs-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs: (40 commits)
f2fs: optimize gc for better performance
f2fs: merge more bios of node block writes
f2fs: avoid an overflow during utilization calculation
f2fs: trigger GC when there are prefree segments
f2fs: use strncasecmp() simplify the string comparison
f2fs: fix omitting to update inode page
f2fs: support the inline xattrs
f2fs: add the truncate_xattr_node function
f2fs: introduce __find_xattr for readability
f2fs: reserve the xattr space dynamically
f2fs: add flags for inline xattrs
f2fs: fix error return code in init_f2fs_fs()
f2fs: fix wrong BUG_ON condition
f2fs: fix memory leak when init f2fs filesystem fail
f2fs: fix a compound statement label error
f2fs: avoid writing inode redundantly when creating a file
f2fs: alloc_page() doesn't return an ERR_PTR
f2fs: should cover i_xattr_nid with its xattr node page lock
f2fs: check the free space first in new_node_page
f2fs: clean up the needless end 'return' of void function
...
Merge branch 'for-linus' of git://git.linaro.org/people/rmk/linux-arm
Pull ARM updates from Russell King:
"This set includes adding support for Neon acceleration of RAID6 XOR
code from Ard Biesheuvel, cache flushing and barrier updates from Will
Deacon, and a cleanup to the ARM debug code which reduces the amount
of code by about 500 lines.
A few other cleanups, such as constifying the machine descriptors
which already shouldn't be written to, cleaning up the printing of the
L2 cache size"
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (55 commits)
ARM: 7826/1: debug: support debug ll on hisilicon soc
ARM: 7830/1: delay: don't bother reporting bogomips in /proc/cpuinfo
ARM: 7829/1: Add ".text.unlikely" and ".text.hot" to arm unwind tables
ARM: 7828/1: ARMv7-M: implement restart routine common to all v7-M machines
ARM: 7827/1: highbank: fix debug uart virtual address for LPAE
ARM: 7823/1: errata: workaround Cortex-A15 erratum 773022
ARM: 7806/1: allow DEBUG_UNCOMPRESS for Tegra
ARM: 7793/1: debug: use generic option for ep93xx PL10x debug port
ARM: debug: move SPEAr debug to generic PL01x code
ARM: debug: move davinci debug to generic 8250 code
ARM: debug: move keystone debug to generic 8250 code
ARM: debug: remove DEBUG_ROCKCHIP_UART
ARM: debug: provide generic option choices for 8250 and PL01x ports
ARM: debug: move PL01X debug include into arch/arm/include/debug/
ARM: debug: provide PL01x debug uart phys/virt address configuration options
ARM: debug: add support for word accesses to debug/8250.S
ARM: debug: move 8250 debug include into arch/arm/include/debug/
ARM: debug: provide 8250 debug uart phys/virt address configuration options
ARM: debug: provide 8250 debug uart register shift configuration option
ARM: debug: provide 8250 debug uart flow control configuration option
...
Pull IDE changes from David Miller:
"Mostly cleanups, and changes part of tree-wide adjustments, this code
is in deep freeze so that's pretty much what we expect these days"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide:
ide: sgiioc4: Staticize ioc4_ide_attach_one()
ide: palm_bk3710: add missing __iomem annotation
ide: use dev_get_platdata()
ide-disk_proc: use macro to replace magic number
ide: replace strict_strtol() with kstrtol()
Pull sparc changes from David Miller:
"Several bug fixes (from Kirill Tkhai, Geery Uytterhoeven, and Alexey
Dobriyan) and some support for Fujitsu sparc64x chips (from Allen
Pais)"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Export flush_ptrace_access() (needed by lustre)
sparc: fix PCI device proc file mmap(2)
sparc64: Remove RWSEM export leftovers
sparc64: Fix off by one in trampoline TLB mapping installation loop.
sparc64: Fix ITLB handler of null page
esp_scsi: Fix tag state corruption when autosensing.
sparc64: Fix not SRA'ed %o5 in 32-bit traced syscall
sparc64: cleanup: Rename ret_from_syscall to ret_from_fork
sparc32: Fix exit flag passed from traced sys_sigreturn
sparc64: Fix wrong syscall return value passed to trace_sys_exit()
support sparc64x chip type in cpumap.c
cpu hw caps support for sparc64x
Pull networking changes from David Miller:
"Noteworthy changes this time around:
1) Multicast rejoin support for team driver, from Jiri Pirko.
2) Centralize and simplify TCP RTT measurement handling in order to
reduce the impact of bad RTO seeding from SYN/ACKs. Also, when
both timestamps and local RTT measurements are available prefer
the later because there are broken middleware devices which
scramble the timestamp.
From Yuchung Cheng.
3) Add TCP_NOTSENT_LOWAT socket option to limit the amount of kernel
memory consumed to queue up unsend user data. From Eric Dumazet.
4) Add a "physical port ID" abstraction for network devices, from
Jiri Pirko.
5) Add a "suppress" operation to influence fib_rules lookups, from
Stefan Tomanek.
6) Add a networking development FAQ, from Paul Gortmaker.
7) Extend the information provided by tcp_probe and add ipv6 support,
from Daniel Borkmann.
8) Use RCU locking more extensively in openvswitch data paths, from
Pravin B Shelar.
9) Add SCTP support to openvswitch, from Joe Stringer.
10) Add EF10 chip support to SFC driver, from Ben Hutchings.
11) Add new SYNPROXY netfilter target, from Patrick McHardy.
12) Compute a rate approximation for sending in TCP sockets, and use
this to more intelligently coalesce TSO frames. Furthermore, add
a new packet scheduler which takes advantage of this estimate when
available. From Eric Dumazet.
13) Allow AF_PACKET fanouts with random selection, from Daniel
Borkmann.
14) Add ipv6 support to vxlan driver, from Cong Wang"
Resolved conflicts as per discussion.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1218 commits)
openvswitch: Fix alignment of struct sw_flow_key.
netfilter: Fix build errors with xt_socket.c
tcp: Add missing braces to do_tcp_setsockopt
caif: Add missing braces to multiline if in cfctrl_linkup_request
bnx2x: Add missing braces in bnx2x:bnx2x_link_initialize
vxlan: Fix kernel panic on device delete.
net: mvneta: implement ->ndo_do_ioctl() to support PHY ioctls
net: mvneta: properly disable HW PHY polling and ensure adjust_link() works
icplus: Use netif_running to determine device state
ethernet/arc/arc_emac: Fix huge delays in large file copies
tuntap: orphan frags before trying to set tx timestamp
tuntap: purge socket error queue on detach
qlcnic: use standard NAPI weights
ipv6:introduce function to find route for redirect
bnx2x: VF RSS support - VF side
bnx2x: VF RSS support - PF side
vxlan: Notify drivers for listening UDP port changes
net: usbnet: update addr_assign_type if appropriate
driver/net: enic: update enic maintainers and driver
driver/net: enic: Exposing symbols for Cisco's low latency driver
...
Use d_materialise_unique() instead of d_splice_alias(). This allows dentry
subtrees to be moved to a new place if there moved, even if something is
referencing a dentry in the subtree (open fd, cwd, etc..).
This will also allow us to drop a subtree if it is found to be replaced by
something else. In this case the disconnected subtree can later be
reconnected to its new location.
d_materialise_unique() ensures that a directory entry only ever has one
alias. We keep fc->inst_mutex around the calls for d_materialise_unique()
on directories to prevent a race with mkdir "stealing" the inode.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
projects / ~andy / linux / log