Boris BREZILLON [Fri, 18 Oct 2013 19:26:51 +0000 (21:26 +0200)]
USB: ehci-atmel: add usb_clk for transition to CCF
The AT91 PMC (Power Management Controller) provides a USB clock used by
the different USB controllers (ehci, ohci and udc).
The atmel-ehci driver must configure the usb clock rate to 48Mhz in order
to get a fully functionnal USB host controller.
This configuration was formely done in mach-at91/clock.c, but will be
bypassed when moving to common clk framework.
This patch adds support for usb clock retrieval and configuration only if
CCF is enabled (CONFIG_COMMON_CLK).
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com> Cc: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bjørn Mork [Tue, 29 Oct 2013 08:52:57 +0000 (09:52 +0100)]
usb: cdc-wdm: ignore speed change notifications
The only notification supported by the Device Management class is
Response Available. But this driver is also used as a subdriver of
other CDC classes, allowing notifications like Speed Change and
Network Connection. This results in log messages which are only
confusing to an end user:
[66255.801874] cdc_mbim 1-3:1.5: unknown notification 42 received: index 5 len 8
These drivers use cdc-wdm as a subdriver to allow access to an
embedded management protocol, and all management is expected to
use this protocol. There is therefore no need to handle any of
these optional CDC notifications. Instead we can let the cdc-wdm
driver recognize them and log a debug level message instead of an
error.
Greg Suarez [Tue, 29 Oct 2013 17:29:10 +0000 (10:29 -0700)]
USB: cdc-wdm: support back-to-back USB_CDC_NOTIFY_RESPONSE_AVAILABLE notifications
Some MBIM devices send back-to-back USB_CDC_NOTIFY_RESPONSE_AVAILABLE notifications
when sending a message over multiple fragments or when there are unsolicited
messages available.
Count up the number of USB_CDC_NOTIFY_RESPONSE_AVAILABLE notifications received
and decrement the count and submit the urb for the next response each time userspace
completes a read the response.
Joe Perches [Sun, 27 Oct 2013 03:41:53 +0000 (20:41 -0700)]
printk: pr_debug_ratelimited: check state first to reduce "callbacks suppressed" messages
pr_debug_ratelimited should be coded similarly to dev_dbg_ratelimited
to reduce the "callbacks suppressed" messages.
Add #include <linux/dynamic_debug.h> to printk.h. Unfortunately, this
new #include must be after the prototype/declaration of function printk.
It may be better to split out these _ratelimited declarations into
a separate file one day.
Any use of these pr_<foo>_ratelimited functions must also have another
specific #include <ratelimited.h>. Most users have this done indirectly
via #include <linux/kernel.h>
printk.h may not #include <linux/ratelimit.h> as it causes circular
dependencies and compilation failures.
Signed-off-by: Joe Perches <joe@perches.com> Tested-by: Krzysztof Mazur <krzysiek@podlesie.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Huang Rui [Mon, 28 Oct 2013 15:31:32 +0000 (23:31 +0800)]
usb: usbtest: support bos descriptor test for usb 3.0
In Test 9 of usbtest module, it is used for performing chapter 9 tests N
times. This patch adds to support getting bos descriptor test scenario for
USB 3.0.
Thomas Pugliese [Wed, 23 Oct 2013 19:44:27 +0000 (14:44 -0500)]
usb: wusbcore: combine multiple isoc frames in a single transfer request.
Combine multiple isoc frames in a single transfer request. This allows
the HWA to take advantage of bursting to deliver data to endpoints
whose logical service interval is less than the minimum wireless USB
service interval of 4ms. Wireless audio quality is much improved after
this update.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Pugliese [Wed, 23 Oct 2013 19:44:26 +0000 (14:44 -0500)]
usb: wusbcore: set the RPIPE wMaxPacketSize value correctly
For isochronous endpoints, set the RPIPE wMaxPacketSize value using
wOverTheAirPacketSize from the endpoint companion descriptor instead of
wMaxPacketSize from the normal endpoint descriptor.
Peter Chen [Tue, 22 Oct 2013 03:13:41 +0000 (11:13 +0800)]
usb: chipidea: host: more enhancement when ci->hcd is NULL
Like http://marc.info/?l=linux-usb&m=138200449428874&w=2 said:
two more things are needed to be done:
- If host_start fails, the host_stop should not be called, so we
add check that ci->hcd is not NULL.
- if the host_start fails at the beginning, we need to consider
regulator mismatch issue.
Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix argument passed to the register setup helper function so
the phy is actually disabled. Now due to cut&paste error 1 is
passed to both phy_power_on() and phy_power_off().
Reported by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Reviewed-by: Jingoo Han <jg1.han@samsung.com> Acked-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern [Fri, 18 Oct 2013 15:19:18 +0000 (11:19 -0400)]
USB: UHCI: check for wakeup/suspend race
hcd-pci.c in usbcore contains a check for wakeup requests racing with
controller suspend. This check is going to be moved out of usbcore
and into the individual controller drivers, where it can apply to all
platforms, not just PCI.
This patch adds the check to uhci-hcd. Ironically, none of the
non-PCI platform drivers for uhci-hcd implement suspend/resume.
Nevertheless, this change is needed to accomodate the upcoming change
to usbcore.
The patch also removes an outdated check of the root hub state. For
one thing, the PM layer has long been quite reliable about suspending
root hubs before controllers. For another, virtually the same check
is also made in hcd-pci.c; there's no point in repeating it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern [Fri, 18 Oct 2013 15:18:21 +0000 (11:18 -0400)]
USB: EHCI: add check for wakeup/suspend race
hcd-pci.c in usbcore contains a check for wakeup requests racing with
controller suspend. This check is going to be moved out of usbcore
and into the individual controller drivers, where it can apply to all
platforms, not just PCI.
This patch adds the check to ehci-hcd.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern [Fri, 18 Oct 2013 15:17:21 +0000 (11:17 -0400)]
USB: change dev_warn about missing reset-resume to dev_dbg
This patch changes a dev_warn() call in usbcore to dev_dbg(). It's
not necessary to warn about drivers missing a reset-resume callback,
since the reset-resume method is optional.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern [Fri, 18 Oct 2013 15:16:07 +0000 (11:16 -0400)]
USB: OHCI: fix and explain sparse errors
This patch fixes an endian-related error in ohci-hcd (detected by
sparse) and clarifies a comment explaining a peculiar locking
arrangement that sparse warns about.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern [Fri, 18 Oct 2013 15:15:14 +0000 (11:15 -0400)]
USB: EHCI: fix sparse errors
This patch fixes several sparse errors in ehci-hcd introduced by
commit 3d091a6f7039 (USB: EHCI: AMD periodic frame list table quirk).
Although the problem fixed by that commit affects only little-endian
systems, the source code has to use types appropriate for big-endian
too.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern [Fri, 18 Oct 2013 15:13:08 +0000 (11:13 -0400)]
USB: EHCI: fix type mismatch in check_intr_schedule
This patch fixes a type mismatch in ehci-hcd caused by commit b35c5009bbf6 (USB: EHCI: create per-TT bandwidth tables). The c_maskp
parameter in check_intr_schedule() was changed to point to unsigned
int rather than __hc32, but the prototype declaration wasn't adjusted
accordingly.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge tag 'for-usb-next-2013-10-17' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-next
Sarah writes:
xhci: Final patches for 3.13
Hi Greg,
Here's my pull request for usb-next and 3.13. My xHCI tree is closed
after this point, since I won't be able to run my full tests while I'm in
Scotland. After Kernel Summit, I'll be on vacation with access to email
from Oct 26th to Nov 6th.
Here's what's in this request:
- Patches to fix USB 2.0 Link PM issues that cause USB 3.0 devices to not
enumerate or misbehave when plugged into a USB 2.0 port. Those are
marked for stable.
- A msec vs jiffies bug fix by xiao jin, which results in fairly harmless
behavior, and thus isn't marked for stable.
- Xenia's patches to refactor the xHCI command handling code, which makes
it much more readable and consistent.
- Misc cleanup patches, one by Sachin Kamat and three from Dan Williams.
Here's what's not in this request:
- Dan's two patches to allow the xHCI host to use the "Windows" or "new"
enumeration scheme. I did not have time to test those, and I want to
run them with as many USB devices as I can get a hold of. That will
have to wait for 3.14.
- Xenia's patches to remove xhci_readl in favor of readl. I'll queue
those for 3.14 after I test them.
- The xHCI streams update, UAS fixes, and usbfs streams support. I'm not
comfortable with changes and fixes to that patchset coming in this late.
I would rather wait for 3.14 and be really sure the streams support is
stable before we add new userspace API and remove CONFIG_BROKEN from the
uas driver.
- Julius' patch to clear the port reset bit on hub resume that came in
a couple days ago. It looks harmless, but I would rather take the time
to test and queue it for usb-linus and the stable trees once 3.13-rc1
is out.
Thomas Pugliese [Mon, 7 Oct 2013 15:07:51 +0000 (10:07 -0500)]
usb: wusbcore: preserve endianness of cached descriptors
Do not overwrite the multi-byte fields of usb_wa_descriptor with their
cpu format values after reading the descriptor. Leave the values as
__le16 and swap on use. This is more consistent with other uses of USB
descriptors.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Pugliese [Mon, 7 Oct 2013 15:53:57 +0000 (10:53 -0500)]
usb: wusbcore: serialize access to the HWA data out endpoint
This patch serializes access to the HWA data transfer out (DTO)
endpoint. This prevents a situation where two transfer requests being
sent concurrently to separate downstream endpoints could interleave
their transfer request and transfer data packets causing data
corruption. The transfer processing code will now attempt to acquire
the DTO resource before sending a transfer to the HWA. If it cannot
acquire the resource, the RPIPE that the transfer is assigned to will
be placed on a waiting list. When the DTO resource is released, the
actor releasing the resource will serivce the RPIPEs that are waiting.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Fri, 18 Oct 2013 23:46:21 +0000 (16:46 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fix from Chris Mason:
"Sage hit a deadlock with ceph on btrfs, and Josef tracked it down to a
regression in our initial rc1 pull. When doing nocow writes we were
sometimes starting a transaction with locks held"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: release path before starting transaction in can_nocow_extent
Linus Torvalds [Fri, 18 Oct 2013 21:26:51 +0000 (14:26 -0700)]
Merge tag 'pm+acpi-3.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
- intel_pstate fix for misbehavior after system resume if sysfs
attributes are set in a specific way before the corresponding suspend
from Dirk Brandewie.
- A recent intel_pstate fix has no effect if unsigned long is 32-bit,
so fix it up to cover that case as well.
- The s3c64xx cpufreq driver was not updated when the index field of
struct cpufreq_frequency_table was replaced with driver_data, so
update it now. From Charles Keepax.
- The Kconfig help text for ACPI_BUTTON still refers to
/proc/acpi/event that has been dropped recently, so modify it to
remove that reference. From Krzysztof Mazur.
- A Lan Tianyu's change adds a missing mutex unlock to an error code
path in acpi_resume_power_resources().
- Some code related to ACPI power resources, whose very purpose is
questionable to put it lightly, turns out to cause problems to happen
during testing on real systems, so remove it completely (we may
revisit that in the future if there's a compelling enough reason).
From Rafael J Wysocki and Aaron Lu.
* tag 'pm+acpi-3.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / PM: Drop two functions that are not used any more
ATA / ACPI: remove power dependent device handling
cpufreq: s3c64xx: Rename index to driver_data
ACPI / power: Drop automaitc resume of power resource dependent devices
intel_pstate: Fix type mismatch warning
cpufreq / intel_pstate: Fix max_perf_pct on resume
ACPI: remove /proc/acpi/event from ACPI_BUTTON help
ACPI / power: Release resource_lock after acpi_power_get_state() return error
* acpi-fixes:
ACPI / PM: Drop two functions that are not used any more
ATA / ACPI: remove power dependent device handling
ACPI / power: Drop automaitc resume of power resource dependent devices
ACPI: remove /proc/acpi/event from ACPI_BUTTON help
ACPI / power: Release resource_lock after acpi_power_get_state() return error
Linus Torvalds [Fri, 18 Oct 2013 01:49:21 +0000 (18:49 -0700)]
Merge branch 'for-linus' of git://git.samba.org/sfrench/cifs-2.6
Pull CIFS fixes from Steve French:
"Five small cifs fixes (includes fixes for: unmount hang, 2 security
related, symlink, large file writes)"
* 'for-linus' of git://git.samba.org/sfrench/cifs-2.6:
cifs: ntstatus_to_dos_map[] is not terminated
cifs: Allow LANMAN auth method for servers supporting unencapsulated authentication methods
cifs: Fix inability to write files >2GB to SMB2/3 shares
cifs: Avoid umount hangs with smb2 when server is unresponsive
do not treat non-symlink reparse points as valid symlinks
Linus Torvalds [Thu, 17 Oct 2013 17:39:01 +0000 (10:39 -0700)]
Merge tag 'driver-core-3.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fix from Greg KH:
"Here is one fix for the hotplug memory path that resolves a regression
when removing memory that showed up in 3.12-rc1"
* tag 'driver-core-3.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
driver core: Release device_hotplug_lock when store_mem_state returns EINVAL
Linus Torvalds [Thu, 17 Oct 2013 17:38:18 +0000 (10:38 -0700)]
Merge tag 'usb-3.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some USB fixes and new device ids for 3.12-rc6
The largest change here is a bunch of new device ids for the option
USB serial driver for new Huawei devices. Other than that, just some
small bug fixes for issues that people have reported (run-time and
build-time), nothing major"
* tag 'usb-3.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: usb_phy_gen: refine conditional declaration of usb_nop_xceiv_register
usb: misc: usb3503: Fix compile error due to incorrect regmap depedency
usb/chipidea: fix oops on memory allocation failure
usb-storage: add quirk for mandatory READ_CAPACITY_16
usb: serial: option: blacklist Olivetti Olicard200
USB: quirks: add touchscreen that is dazzeled by remote wakeup
Revert "usb: musb: gadget: fix otg active status flag"
USB: quirks.c: add one device that cannot deal with suspension
USB: serial: option: add support for Inovia SEW858 device
USB: serial: ti_usb_3410_5052: add Abbott strip port ID to combined table as well.
USB: support new huawei devices in option.c
usb: musb: start musb on the udc side, too
xhci: Fix spurious wakeups after S5 on Haswell
xhci: fix write to USB3_PSSEN and XUSB2PRM pci config registers
xhci: quirk for extra long delay for S4
xhci: Don't enable/disable RWE on bus suspend/resume.
Linus Torvalds [Thu, 17 Oct 2013 17:37:42 +0000 (10:37 -0700)]
Merge tag 'tty-3.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull serial driver fixes from Greg KH:
"Here are two serial driver fixes for your tree. One is a revert of a
patch that causes a build error, the other is a fix to provide the
correct brace placement which resolves a bug where the driver was not
working properly"
* tag 'tty-3.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: vt8500: add missing braces
Revert "serial: i.MX: evaluate linux,stdout-path property"
Linus Torvalds [Thu, 17 Oct 2013 17:36:57 +0000 (10:36 -0700)]
Merge tag 'char-misc-3.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some small iio and w1 driver fixes for 3.12-rc6.
There is also a hyper-v fix in here, which turned out to be incorrect,
so it was reverted. That will probably have to wait unto 3.13-rc1 to
get accepted as it's still being discussed"
* tag 'char-misc-3.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Revert "Drivers: hv: vmbus: Fix a bug in channel rescind code"
Drivers: hv: vmbus: Fix a bug in channel rescind code
iio:buffer: Free active scan mask in iio_disable_all_buffers()
iio: frequency: adf4350: add missing clk_disable_unprepare() on error in adf4350_probe()
w1 - call request_module with w1 master mutex unlocked
w1 - fix fops in w1_bus_notify
Linus Torvalds [Thu, 17 Oct 2013 17:17:25 +0000 (10:17 -0700)]
Merge tag 'sound-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"All reasonably small fixes as rc6: a HD-audio mic fix, a us122l mmap
regression fix, and kernel memory leak fix in hdsp driver. Hopefully
this will be the last pull request for 3.12..."
* tag 'sound-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hdsp - info leak in snd_hdsp_hwdep_ioctl()
ALSA: us122l: Fix pcm_usb_stream mmapping regression
ALSA: hda - Fix inverted internal mic not indicated on some machines
Linus Torvalds [Thu, 17 Oct 2013 17:16:45 +0000 (10:16 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull apparmor fixes from James Morris:
"A couple more regressions fixed"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
apparmor: fix bad lock balance when introspecting policy
apparmor: fix memleak of the profile hash
Merge tag 'iio-fixes-for-3.12c' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-linus
Jonathan writes:
Third set of IIO fixes for the 3.12 cycle.
Two little ones this time:
1) A missing clk_unprepare in adf4350.
2) A missing free of the active_scan_mask when iio_disable_all_buffers is
called during an unexpected device removal. This leak was introduced by
the fix a87c82e454f184a9473f8cdfd4d304205f585f65 iio: Stop sampling when the device is removed
and hence is a regression fix.
Guenter Roeck [Thu, 17 Oct 2013 02:18:41 +0000 (19:18 -0700)]
usb: usb_phy_gen: refine conditional declaration of usb_nop_xceiv_register
Commit 3fa4d734 (usb: phy: rename nop_usb_xceiv => usb_phy_gen_xceiv)
changed the conditional around the declaration of usb_nop_xceiv_register
from
#if defined(CONFIG_NOP_USB_XCEIV) ||
(defined(CONFIG_NOP_USB_XCEIV_MODULE) && defined(MODULE))
to
#if IS_ENABLED(CONFIG_NOP_USB_XCEIV)
While that looks the same, it is semantically different. The first expression
is true if CONFIG_NOP_USB_XCEIV is built as module and if the including
code is built as module. The second expression is true if code depending on
CONFIG_NOP_USB_XCEIV if built as module or into the kernel.
As a result, the arm:allmodconfig build fails with
arch/arm/mach-omap2/built-in.o: In function `omap3_evm_init':
arch/arm/mach-omap2/board-omap3evm.c:703: undefined reference to
`usb_nop_xceiv_register'
Fix the problem by reverting to the old conditional.
usb: musb: cppi41: allow to defer probing if DMA isn't yet available
If everything (musb, cppi41, phy) is built-in then musb will start
without the dma engine printing only
|musb-hdrc musb-hdrc.0.auto: Falied to request rx1.
The reason for this is that the musb device structs are created & probed
before those of the cppi41 device. So the cppi41 device is probed too
late.
As a workaround for this allow the musb_cppi41 part to defer the probe
if everything is fine except for the missing DMA controller. In case of
another error we continue.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: musb: core: Call dma_controller_destroy() in error path only once.
In commit f3ce4d5 ("usb: musb: core: call dma_controller_destroy() in the err path")
I erroneously assumed that the dma controller is not removed in the
error patch. This was wrong because it happens later via musb_free().
That means the original commit can be reverted because it is wrong or we
do this, so it is more obvious.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
The patch fixes two issues in the error path cleanup:
- in MUSB_PORT_MODE_DUAL_ROLE mode, if musb_gadget_setup() fails we
never cleanup the host struct earlier allocated.
- if musb_init_debugfs() or sysfs_create_group() fails, then we never
free the host part initialization, only device part.
Cc: stable@vger.kernel.org # v3.11 Cc: Daniel Mack <zonque@gmail.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
Revert "Drivers: hv: vmbus: Fix a bug in channel rescind code"
This reverts commit 90d33f3ec519db19d785216299a4ee85ef58ec97 as it's not
the correct fix for this issue, and it causes a build warning to be
added to the kernel tree.
Cc: K. Y. Srinivasan <kys@microsoft.com> Cc: <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix spacing, improve error code returned, remove unused #define,
use strtobool() instead of kstrtou8().
Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: musb: dsps: run the timer only on OTG systems
I introduced this check here because it looked wrong in HOST only
configurions. The timer would remove that session bit and will never
come back and so there would not be another session.
Now that I played with OTG for a while I belive this workaround is
only required for the OTG mode because we have to end the session and
then we have to try to start manually.
Therefore, this patch limits this timer to the OTG only port mode so we
don't need to poll around in device only mode.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
According to the comments, we rely on the OTG timer because the core
does not expose some important OTG details. So far this is all I
know. After playing with OTG I stumbled over a problem:
musb is recognized as a B-device without a problem. Whenever a cable is
plugged, the VBUS rises, musb recognizes this as a starting session,
sets the MUSB_DEVCTL_SESSION bit by itself and a RESET interrupt occurs,
the session starts. Good.
After a disconnect, the timer is started and re-starts itself because
it remains in B_IDLE with the BDEVICE set. I didn't figure the the
reason or the need for it. Nothing changes here except for OTG state
from B to A device if the BDEVICE bit disappears. This doesn't make much
sense to me because nothing happens after this. _IF_ we receive an
interrupt before the state change then we may act on wrong condition.
Plugging a B-device (and letting MUSB act as host) doesn't work here.
The reason seems to be that the MUSB tries to start a session, it fails
and then it removes the bit. So we never start as a host.
This patch sets the MUSB_DEVCTL_SESSION bit in the IDLE state so musb
can try to establish a session as host. After the bit is set, musb tries
to start a session and if it fails it clears the bit. Therefore it will
try over and over again until a session either as host or as device is
established.
The readout of the MUSB_DEVCTL register after the removal the
MUSB_DEVCTL_SESSION (in A_WAIT_BCON) has been removed because it did not
contain the BDEVICE bit set (in the second read) leading to A_IDLE. After
plugging a host musb assumed that it is also a host and complained about
a missing reset. However a third read of the register has has the BDEVICE
bit set so it seems that it is not stable.
This mostly what da8xx.c is doing except that we set the timer also
after A_WAIT_BCON so the session bit can be triggered.
Whit this change I was able to keep am335x-evm in OTG mode and plug in
either a HOST or a DEVICE and in a random order and the device was
recognized.
Cc: stable@vger.kernel.org # v3.11 Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
The timer is initialized right after musb is probed. There is actually
no need to have this timer running because _nothing_ will happen until
we have the gadget loaded. Also we need this timer only if we run in OTG
mode _and_ we need it also after the gadget has been replaced with
another one.
I've been looking at am35x.c, da8xx.c, omap2430.c, tusb6010.c. da8xx
seem to have the same problem as dsps and doing mostly the same thing.
tusb6010 seem to do something different and do some actual "idle / power
saving" work so I am not too comfortable to remove
musb_platform_try_idle() from musb_gadget_setup().
Therefore this patch does not start the timer if there is no gadget
active (which is at musb_gadget_setup() at time). In order to have the
timer active after the gadget is loaded it will be triggered from
dsps_musb_enable().
Cc: stable@vger.kernel.org # v3.11 Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: musb: call musb_start() only once in OTG mode
In commit 001dd84 ("usb: musb: start musb on the udc side, too") it was
ensured that the state engine is started also in OTG mode after a
removal / insertion of the gadget.
Unfortunately this change also introduced a bug: If the device is
configured as OTG and it connected with a remote host _without_ loading
a gadget then we bug() later (because musb->otg->gadget is not
initialized).
Initially I assumed it might be nice to have the host part of musb in
OTG mode working without having a gadget loaded. This bug and fact that
it wasn't working like this before the host/gadget split made me realize
that this was a silly idea.
This patch now introduces back the old behavior where in OTG mode the
host mode is only working after the gadget has been loaded.
Cc: stable@vger.kernel.org # v3.11 Cc: Daniel Mack <zonque@gmail.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
ACPI / PM: Drop two functions that are not used any more
Two functions defined in device_pm.c, acpi_dev_pm_add_dependent()
and acpi_dev_pm_remove_dependent(), have no callers and may be
dropped, so drop them.
Moreover, they are the only functions adding entries to and removing
entries from the power_dependent list in struct acpi_device, so drop
that list too.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Aaron Lu [Thu, 17 Oct 2013 13:38:53 +0000 (15:38 +0200)]
ATA / ACPI: remove power dependent device handling
Previously, we wanted SCSI devices corrsponding to ATA devices to
be runtime resumed when the power resource for those ATA device was
turned on by some other device, so we added the SCSI device to the
dependent device list of the ATA device's ACPI node. However, this
code has no effect after commit 41863fc (ACPI / power: Drop automaitc
resume of power resource dependent devices) and the mechanism it was
supposed to implement is regarded as a bad idea now, so drop it.
[rjw: Changelog] Signed-off-by: Aaron Lu <aaron.lu@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Linus Torvalds [Thu, 17 Oct 2013 04:36:03 +0000 (21:36 -0700)]
Merge branch 'akpm' (fixes from Andrew Morton)
Merge misc fixes from Andrew Morton.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (21 commits)
mm: revert mremap pud_free anti-fix
mm: fix BUG in __split_huge_page_pmd
swap: fix set_blocksize race during swapon/swapoff
procfs: call default get_unmapped_area on MMU-present architectures
procfs: fix unintended truncation of returned mapped address
writeback: fix negative bdi max pause
percpu_refcount: export symbols
fs: buffer: move allocation failure loop into the allocator
mm: memcg: handle non-error OOM situations more gracefully
tools/testing/selftests: fix uninitialized variable
block/partitions/efi.c: treat size mismatch as a warning, not an error
mm: hugetlb: initialize PG_reserved for tail pages of gigantic compound pages
mm/zswap: bugfix: memory leak when re-swapon
mm: /proc/pid/pagemap: inspect _PAGE_SOFT_DIRTY only on present pages
mm: migration: do not lose soft dirty bit if page is in migration state
gcov: MAINTAINERS: Add an entry for gcov
mm/hugetlb.c: correct missing private flag clearing
mm/vmscan.c: don't forget to free shrinker->nr_deferred
ipc/sem.c: synchronize semop and semctl with IPC_RMID
ipc: update locking scheme comments
...
Hugh Dickins [Wed, 16 Oct 2013 20:47:09 +0000 (13:47 -0700)]
mm: revert mremap pud_free anti-fix
Revert commit 1ecfd533f4c5 ("mm/mremap.c: call pud_free() after fail
calling pmd_alloc()").
The original code was correct: pud_alloc(), pmd_alloc(), pte_alloc_map()
ensure that the pud, pmd, pt is already allocated, and seldom do they
need to allocate; on failure, upper levels are freed if appropriate by
the subsequent do_munmap(). Whereas commit 1ecfd533f4c5 did an
unconditional pud_free() of a most-likely still-in-use pud: saved only
by the near-impossiblity of pmd_alloc() failing.
Signed-off-by: Hugh Dickins <hughd@google.com> Cc: Chen Gang <gang.chen@asianux.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hugh Dickins [Wed, 16 Oct 2013 20:47:08 +0000 (13:47 -0700)]
mm: fix BUG in __split_huge_page_pmd
Occasionally we hit the BUG_ON(pmd_trans_huge(*pmd)) at the end of
__split_huge_page_pmd(): seen when doing madvise(,,MADV_DONTNEED).
It's invalid: we don't always have down_write of mmap_sem there: a racing
do_huge_pmd_wp_page() might have copied-on-write to another huge page
before our split_huge_page() got the anon_vma lock.
Forget the BUG_ON, just go back and try again if this happens.
Signed-off-by: Hugh Dickins <hughd@google.com> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: David Rientjes <rientjes@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
swap: fix set_blocksize race during swapon/swapoff
Fix race between swapoff and swapon. Swapoff used old_block_size from
swap_info outside of swapon_mutex so it could be overwritten by
concurrent swapon.
The race has visible effect only if more than one swap block device
exists with different block sizes (e.g. /dev/sda1 with block size 4096
and /dev/sdb1 with 512). In such case it leads to setting the blocksize
of swapped off device with wrong blocksize.
The bug can be triggered with multiple concurrent swapoff and swapon:
0. Swap for some device is on.
1. swapoff:
First the swapoff is called on this device and "struct swap_info_struct
*p" is assigned. This is done under swap_lock however this lock is
released for the call try_to_unuse().
2. swapon:
After the assignment above (and before acquiring swapon_mutex &
swap_lock by swapoff) the swapon is called on the same device.
The p->old_block_size is assigned to the value of block_size the device.
This block size should be the same as previous but sometimes it is not.
The swapon ends successfully.
3. swapoff:
Swapoff resumes, grabs the locks and mutex and continues to disable this
swap device. Now it sets the block size to value taken from swap_info
which was overwritten by swapon in 2.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Reported-by: Weijie Yang <weijie.yang.kh@gmail.com> Cc: Bob Liu <bob.liu@oracle.com> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Shaohua Li <shli@fusionio.com> Cc: Minchan Kim <minchan@kernel.org> Acked-by: Hugh Dickins <hughd@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
HATAYAMA Daisuke [Wed, 16 Oct 2013 20:47:05 +0000 (13:47 -0700)]
procfs: call default get_unmapped_area on MMU-present architectures
Commit c4fe24485729 ("sparc: fix PCI device proc file mmap(2)") added
proc_reg_get_unmapped_area in proc_reg_file_ops and
proc_reg_file_ops_no_compat, by which now mmap always returns EIO if
get_unmapped_area method is not defined for the target procfs file,
which causes regression of mmap on /proc/vmcore.
To address this issue, like get_unmapped_area(), call default
current->mm->get_unmapped_area on MMU-present architectures if
pde->proc_fops->get_unmapped_area, i.e. the one in actual file
operation in the procfs file, is not defined.
Reported-by: Michael Holzheu <holzheu@linux.vnet.ibm.com> Signed-off-by: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com> Cc: Alexey Dobriyan <adobriyan@gmail.com> Cc: David S. Miller <davem@davemloft.net> Tested-by: Michael Holzheu <holzheu@linux.vnet.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
HATAYAMA Daisuke [Wed, 16 Oct 2013 20:47:04 +0000 (13:47 -0700)]
procfs: fix unintended truncation of returned mapped address
Currently, proc_reg_get_unmapped_area truncates upper 32-bit of the
mapped virtual address returned from get_unmapped_area method in
pde->proc_fops due to the variable rv of signed integer on x86_64. This
is too small to have vitual address of unsigned long on x86_64 since on
x86_64, signed integer is of 4 bytes while unsigned long is of 8 bytes.
To fix this issue, use unsigned long instead.
Fixes a regression added in commit c4fe24485729 ("sparc: fix PCI device
proc file mmap(2)").
Signed-off-by: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com> Cc: Alexey Dobriyan <adobriyan@gmail.com> Cc: David S. Miller <davem@davemloft.net> Tested-by: Michael Holzheu <holzheu@linux.vnet.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since pause is bounded by [min_pause, max_pause] where min_pause is also
bounded by max_pause. It's suspected and demonstrated that the
max_pause calculation goes wrong:
The problem lies in the two "long = unsigned long" assignments in
bdi_max_pause() which might go negative if the highest bit is 1, and the
min_t(long, ...) check failed to protect it falling under 0. Fix all of
them by using "unsigned long" throughout the function.
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com> Reported-by: Toralf Förster <toralf.foerster@gmx.de> Tested-by: Toralf Förster <toralf.foerster@gmx.de> Reviewed-by: Jan Kara <jack@suse.cz> Cc: Richard Weinberger <richard@nod.at> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johannes Weiner [Wed, 16 Oct 2013 20:47:00 +0000 (13:47 -0700)]
fs: buffer: move allocation failure loop into the allocator
Buffer allocation has a very crude indefinite loop around waking the
flusher threads and performing global NOFS direct reclaim because it can
not handle allocation failures.
The most immediate problem with this is that the allocation may fail due
to a memory cgroup limit, where flushers + direct reclaim might not make
any progress towards resolving the situation at all. Because unlike the
global case, a memory cgroup may not have any cache at all, only
anonymous pages but no swap. This situation will lead to a reclaim
livelock with insane IO from waking the flushers and thrashing unrelated
filesystem cache in a tight loop.
Use __GFP_NOFAIL allocations for buffers for now. This makes sure that
any looping happens in the page allocator, which knows how to
orchestrate kswapd, direct reclaim, and the flushers sensibly. It also
allows memory cgroups to detect allocations that can't handle failure
and will allow them to ultimately bypass the limit if reclaim can not
make progress.
Reported-by: azurIt <azurit@pobox.sk> Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Cc: Michal Hocko <mhocko@suse.cz> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johannes Weiner [Wed, 16 Oct 2013 20:46:59 +0000 (13:46 -0700)]
mm: memcg: handle non-error OOM situations more gracefully
Commit 3812c8c8f395 ("mm: memcg: do not trap chargers with full
callstack on OOM") assumed that only a few places that can trigger a
memcg OOM situation do not return VM_FAULT_OOM, like optional page cache
readahead. But there are many more and it's impractical to annotate
them all.
First of all, we don't want to invoke the OOM killer when the failed
allocation is gracefully handled, so defer the actual kill to the end of
the fault handling as well. This simplifies the code quite a bit for
added bonus.
Second, since a failed allocation might not be the abrupt end of the
fault, the memcg OOM handler needs to be re-entrant until the fault
finishes for subsequent allocation attempts. If an allocation is
attempted after the task already OOMed, allow it to bypass the limit so
that it can quickly finish the fault and invoke the OOM killer.
Reported-by: azurIt <azurit@pobox.sk> Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Cc: Michal Hocko <mhocko@suse.cz> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Doug Anderson [Wed, 16 Oct 2013 20:46:57 +0000 (13:46 -0700)]
block/partitions/efi.c: treat size mismatch as a warning, not an error
In commit 27a7c642174e ("partitions/efi: account for pmbr size in lba")
we started treating bad sizes in lba field of the partition that has the
0xEE (GPT protective) as errors.
However, we may run into these "bad sizes" in the real world if someone
uses dd to copy an image from a smaller disk to a bigger disk. Since
this case used to work (even without using force_gpt), keep it working
and treat the size mismatch as a warning instead of an error.
Reported-by: Josh Triplett <josh@joshtriplett.org> Reported-by: Sean Paul <seanpaul@chromium.org> Signed-off-by: Doug Anderson <dianders@chromium.org> Reviewed-by: Josh Triplett <josh@joshtriplett.org> Acked-by: Davidlohr Bueso <davidlohr@hp.com> Tested-by: Artem Bityutskiy <dedekind1@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrea Arcangeli [Wed, 16 Oct 2013 20:46:56 +0000 (13:46 -0700)]
mm: hugetlb: initialize PG_reserved for tail pages of gigantic compound pages
Commit 11feeb498086 ("kvm: optimize away THP checks in
kvm_is_mmio_pfn()") introduced a memory leak when KVM is run on gigantic
compound pages.
That commit depends on the assumption that PG_reserved is identical for
all head and tail pages of a compound page. So that if get_user_pages
returns a tail page, we don't need to check the head page in order to
know if we deal with a reserved page that requires different
refcounting.
The assumption that PG_reserved is the same for head and tail pages is
certainly correct for THP and regular hugepages, but gigantic hugepages
allocated through bootmem don't clear the PG_reserved on the tail pages
(the clearing of PG_reserved is done later only if the gigantic hugepage
is freed).
This patch corrects the gigantic compound page initialization so that we
can retain the optimization in 11feeb498086. The cacheline was already
modified in order to set PG_tail so this won't affect the boot time of
large memory systems.
[akpm@linux-foundation.org: tweak comment layout and grammar] Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Reported-by: andy123 <ajs124.ajs124@gmail.com> Acked-by: Rik van Riel <riel@redhat.com> Cc: Gleb Natapov <gleb@redhat.com> Cc: Mel Gorman <mgorman@suse.de> Cc: Hugh Dickins <hughd@google.com> Acked-by: Rafael Aquini <aquini@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Weijie Yang [Wed, 16 Oct 2013 20:46:54 +0000 (13:46 -0700)]
mm/zswap: bugfix: memory leak when re-swapon
zswap_tree is not freed when swapoff, and it got re-kmalloced in swapon,
so a memory leak occurs.
Free the memory of zswap_tree in zswap_frontswap_invalidate_area().
Signed-off-by: Weijie Yang <weijie.yang@samsung.com> Reviewed-by: Bob Liu <bob.liu@oracle.com> Cc: Minchan Kim <minchan@kernel.org> Reviewed-by: Minchan Kim <minchan@kernel.org> Cc: <stable@vger.kernel.org>
From: Weijie Yang <weijie.yang@samsung.com>
Subject: mm/zswap: bugfix: memory leak when invalidate and reclaim occur concurrently
Consider the following scenario:
thread 0: reclaim entry x (get refcount, but not call zswap_get_swap_cache_page)
thread 1: call zswap_frontswap_invalidate_page to invalidate entry x.
finished, entry x and its zbud is not freed as its refcount != 0
now, the swap_map[x] = 0
thread 0: now call zswap_get_swap_cache_page
swapcache_prepare return -ENOENT because entry x is not used any more
zswap_get_swap_cache_page return ZSWAP_SWAPCACHE_NOMEM
zswap_writeback_entry do nothing except put refcount
Now, the memory of zswap_entry x and its zpage leak.
Modify:
- check the refcount in fail path, free memory if it is not referenced.
- use ZSWAP_SWAPCACHE_FAIL instead of ZSWAP_SWAPCACHE_NOMEM as the fail path
can be not only caused by nomem but also by invalidate.
[akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Weijie Yang <weijie.yang@samsung.com> Reviewed-by: Bob Liu <bob.liu@oracle.com> Cc: Minchan Kim <minchan@kernel.org> Cc: <stable@vger.kernel.org> Acked-by: Seth Jennings <sjenning@linux.vnet.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cyrill Gorcunov [Wed, 16 Oct 2013 20:46:53 +0000 (13:46 -0700)]
mm: /proc/pid/pagemap: inspect _PAGE_SOFT_DIRTY only on present pages
If a page we are inspecting is in swap we may occasionally report it as
having soft dirty bit (even if it is clean). The pte_soft_dirty helper
should be called on present pte only.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org> Cc: Pavel Emelyanov <xemul@parallels.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Matt Mackall <mpm@selenic.com> Cc: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com> Cc: Marcelo Tosatti <mtosatti@redhat.com> Cc: KOSAKI Motohiro <kosaki.motohiro@gmail.com> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Peter Zijlstra <peterz@infradead.org> Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com> Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: Mel Gorman <mel@csn.ul.ie> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cyrill Gorcunov [Wed, 16 Oct 2013 20:46:51 +0000 (13:46 -0700)]
mm: migration: do not lose soft dirty bit if page is in migration state
If page migration is turned on in config and the page is migrating, we
may lose the soft dirty bit. If fork and mprotect are called on
migrating pages (once migration is complete) pages do not obtain the
soft dirty bit in the correspond pte entries. Fix it adding an
appropriate test on swap entries.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org> Cc: Pavel Emelyanov <xemul@parallels.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Matt Mackall <mpm@selenic.com> Cc: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com> Cc: Marcelo Tosatti <mtosatti@redhat.com> Cc: KOSAKI Motohiro <kosaki.motohiro@gmail.com> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Peter Zijlstra <peterz@infradead.org> Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com> Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: Mel Gorman <mel@csn.ul.ie> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joonsoo Kim [Wed, 16 Oct 2013 20:46:48 +0000 (13:46 -0700)]
mm/hugetlb.c: correct missing private flag clearing
We should clear the page's private flag when returing the page to the
hugepage pool. Otherwise, marked hugepage can be allocated to the user
who tries to allocate the non-reserved hugepage. If this user fail to
map this hugepage, he would try to return the page to the hugepage pool.
Since this page has a private flag, resv_huge_pages would mistakenly
increase. This patch fixes this situation.
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Rik van Riel <riel@redhat.com> Cc: Mel Gorman <mgorman@suse.de> Cc: Michal Hocko <mhocko@suse.cz> Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Hugh Dickins <hughd@google.com> Cc: Davidlohr Bueso <davidlohr.bueso@hp.com> Cc: David Gibson <david@gibson.dropbear.id.au> Cc: Wanpeng Li <liwanp@linux.vnet.ibm.com> Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: Hillf Danton <dhillf@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Manfred Spraul [Wed, 16 Oct 2013 20:46:45 +0000 (13:46 -0700)]
ipc/sem.c: synchronize semop and semctl with IPC_RMID
After acquiring the semlock spinlock, operations must test that the
array is still valid.
- semctl() and exit_sem() would walk stale linked lists (ugly, but
should be ok: all lists are empty)
- semtimedop() would sleep forever - and if woken up due to a signal -
access memory after free.
The patch also:
- standardizes the tests for .deleted, so that all tests in one
function leave the function with the same approach.
- unconditionally tests for .deleted immediately after every call to
sem_lock - even it it means that for semctl(GETALL), .deleted will be
tested twice.
Both changes make the review simpler: After every sem_lock, there must
be a test of .deleted, followed by a goto to the cleanup code (if the
function uses "goto cleanup").
The only exception is semctl_down(): If sem_ids().rwsem is locked, then
the presence in ids->ipcs_idr is equivalent to !.deleted, thus no
additional test is required.
Signed-off-by: Manfred Spraul <manfred@colorfullife.com> Cc: Mike Galbraith <efault@gmx.de> Acked-by: Davidlohr Bueso <davidlohr@hp.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Davidlohr Bueso [Wed, 16 Oct 2013 20:46:45 +0000 (13:46 -0700)]
ipc: update locking scheme comments
The initial documentation was a bit incomplete, update accordingly.
[akpm@linux-foundation.org: make it more readable in 80 columns] Signed-off-by: Davidlohr Bueso <davidlohr@hp.com> Acked-by: Manfred Spraul <manfred@colorfullife.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Rientjes [Wed, 16 Oct 2013 20:46:43 +0000 (13:46 -0700)]
mm, memcg: protect mem_cgroup_read_events for cpu hotplug
for_each_online_cpu() needs the protection of {get,put}_online_cpus() so
cpu_online_mask doesn't change during the iteration.
cpu_hotplug.lock is held while a cpu is going down, it's a coarse lock
that is used kernel-wide to synchronize cpu hotplug activity. Memcg has
a cpu hotplug notifier, called while there may not be any cpu hotplug
refcounts, which drains per-cpu event counts to memcg->nocpu_base.events
to maintain a cumulative event count as cpus disappear. Without
get_online_cpus() in mem_cgroup_read_events(), it's possible to account
for the event count on a dying cpu twice, and this value may be
significantly large.
In fact, all memcg->pcp_counter_lock use should be nested by
{get,put}_online_cpus().
This fixes that issue and ensures the reported statistics are not vastly
over-reported during cpu hotplug.
Signed-off-by: David Rientjes <rientjes@google.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Michal Hocko <mhocko@suse.cz> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
driver core: Release device_hotplug_lock when store_mem_state returns EINVAL
When inserting a wrong value to /sys/devices/system/memory/memoryX/state file,
following messages are shown. And device_hotplug_lock is never released.
================================================
[ BUG: lock held when returning to user space! ]
3.12.0-rc4-debug+ #3 Tainted: G W
------------------------------------------------
bash/6442 is leaving the kernel with locks still held!
1 lock held by bash/6442:
#0: (device_hotplug_lock){+.+.+.}, at: [<ffffffff8146cbb5>] lock_device_hotplug_sysfs+0x15/0x50
This issue was introdued by commit fa2be40 (drivers: base: use standard
device online/offline for state change).
This patch releases device_hotplug_lcok when store_mem_state returns EINVAL.
Linus Torvalds [Thu, 17 Oct 2013 00:16:57 +0000 (17:16 -0700)]
Merge tag 'dm-3.12-fix-cve' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device-mapper fix from Alasdair Kergon:
"A patch to avoid data corruption in a device-mapper snapshot.
This is primarily a data corruption bug that all users of
device-mapper snapshots will want to fix. The CVE is due to a data
leak under specific circumstances if, for example, the snapshot is
presented to a virtual machine: a block written as data inside the VM
can get interpreted incorrectly on the host outside the VM as
metadata, causing the host to provide the VM with access to blocks it
would not otherwise see. This is likely to affect few, if any,
people"
* tag 'dm-3.12-fix-cve' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm snapshot: fix data corruption
Linus Torvalds [Thu, 17 Oct 2013 00:15:57 +0000 (17:15 -0700)]
Merge tag 'gpio-v3.12-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull gpio fixes from Linus Walleij:
"Three GPIO fixes for the v3.12 series:
- A fix to the Lynxpoint IRQ handler
- Two late fixes to fallout from the gpiod refactoring"
* tag 'gpio-v3.12-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpiolib: let gpiod_request() return -EPROBE_DEFER
gpiolib: safer implementation of desc_to_gpio()
gpio/lynxpoint: check if the interrupt is enabled in IRQ handler
Dan Williams [Mon, 7 Oct 2013 18:58:20 +0000 (11:58 -0700)]
usb: hub_activate kill an 'else'
Remove a few extra lines and make it clear that all implementations
disable the port by sharing the same line of code.
Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Charles Keepax [Mon, 14 Oct 2013 18:36:47 +0000 (19:36 +0100)]
cpufreq: s3c64xx: Rename index to driver_data
The index field of cpufreq_frequency_table has been renamed to
driver_data by commit 5070158 (cpufreq: rename index as driver_data
in cpufreq_frequency_table).
This patch updates the s3c64xx driver to match.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Cc: 3.11+ <stable@vger.kernel.org> # 3.11+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPI / power: Drop automaitc resume of power resource dependent devices
The mechanism causing devices depending on a given power resource
(that is, devices that can be in D0 only if that power resource is
on) to be resumed automatically when the power resource is turned
on (and their "inferred" power state becomes D0 as a result) is
inherently racy and in fact unnecessary.
It is racy, because if the power resource is turned on and then
immediately off, the device resume triggered by the first transition
to "on" may still happen, causing the power resource to be turned
on again. That again will trigger the "resume of dependent devices"
mechanism, but if the devices in question are not in use, they will
be suspended in the meantime causing the power resource to be turned
off. However, the "resume of dependent devices" will next resume
them again and so on. In some cases (USB port PM in particular) that
leads to an endless busy loop of flipping the resource on and off
continuously.
It is needless, because whoever turns a power resource on will most
likely turn it off at some point and the devices that go into "D0"
as a result of turning it on will then go back into D3cold
(generally, the state they were in before).
Moreover, turning on all power resources a device needs to go into
D0 is not sufficient for a full transition into D0 in general.
Namely, _PS0 may need to be executed in addition to that in some
cases. This means that the whole rationale of the "resume of
dependent devices" mechanism was incorrect to begin with and it's
best to remove it entirely.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Matthew Dawson [Wed, 16 Oct 2013 04:11:24 +0000 (00:11 -0400)]
usb: misc: usb3503: Fix compile error due to incorrect regmap depedency
The USB3503 driver had an incorrect depedency on REGMAP, instead of
REGMAP_I2C. This caused the build to fail since the necessary regmap
i2c pieces were not available.
Signed-off-by: Matthew Dawson <matthew@mjdsystems.ca> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb/chipidea: fix oops on memory allocation failure
When CMA fails to initialize in v3.12-rc4, the chipidea driver oopses
the kernel while trying to remove and put the HCD which doesn't exist:
WARNING: CPU: 0 PID: 6 at /home/rmk/git/linux-rmk/arch/arm/mm/dma-mapping.c:511
__dma_alloc+0x200/0x240()
coherent pool not initialised!
Modules linked in:
CPU: 0 PID: 6 Comm: kworker/u2:0 Tainted: G W 3.12.0-rc4+ #56
Workqueue: deferwq deferred_probe_work_func
Backtrace:
[<c001218c>] (dump_backtrace+0x0/0x10c) from [<c0012328>] (show_stack+0x18/0x1c)
r6:c05fd9cc r5:000001ff r4:00000000 r3:df86ad00
[<c0012310>] (show_stack+0x0/0x1c) from [<c05f3a4c>] (dump_stack+0x70/0x8c)
[<c05f39dc>] (dump_stack+0x0/0x8c) from [<c00230a8>] (warn_slowpath_common+0x6c/0x8c)
r4:df883a60 r3:df86ad00
[<c002303c>] (warn_slowpath_common+0x0/0x8c) from [<c002316c>] (warn_slowpath_fmt+0x38/0x40)
r8:ffffffff r7:00001000 r6:c083b808 r5:00000000 r4:df2efe80
[<c0023134>] (warn_slowpath_fmt+0x0/0x40) from [<c00196bc>] (__dma_alloc+0x200/0x240)
r3:00000000 r2:c05fda00
[<c00194bc>] (__dma_alloc+0x0/0x240) from [<c001982c>] (arm_dma_alloc+0x88/0xa0)
[<c00197a4>] (arm_dma_alloc+0x0/0xa0) from [<c03e2904>] (ehci_setup+0x1f4/0x438)
[<c03e2710>] (ehci_setup+0x0/0x438) from [<c03cbd60>] (usb_add_hcd+0x18c/0x664)
[<c03cbbd4>] (usb_add_hcd+0x0/0x664) from [<c03e89f4>] (host_start+0xf0/0x180)
[<c03e8904>] (host_start+0x0/0x180) from [<c03e7c34>] (ci_hdrc_probe+0x360/0x670
)
r6:df2ef410 r5:00000000 r4:df2c3010 r3:c03e8904
[<c03e78d4>] (ci_hdrc_probe+0x0/0x670) from [<c0311044>] (platform_drv_probe+0x20/0x24)
[<c0311024>] (platform_drv_probe+0x0/0x24) from [<c030fcac>] (driver_probe_device+0x9c/0x234)
...
---[ end trace c88ccaf3969e8422 ]---
Unable to handle kernel NULL pointer dereference at virtual address 00000028
pgd = c0004000
[00000028] *pgd=00000000
Internal error: Oops: 17 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 6 Comm: kworker/u2:0 Tainted: G W 3.12.0-rc4+ #56
Workqueue: deferwq deferred_probe_work_func
task: df86ad00 ti: df882000 task.ti: df882000
PC is at usb_remove_hcd+0x10/0x150
LR is at host_stop+0x1c/0x3c
pc : [<c03cacec>] lr : [<c03e88e4>] psr: 60000013
sp : df883b50 ip : df883b78 fp : df883b74
r10: c11f4c54 r9 : c0836450 r8 : df30c400
r7 : fffffff4 r6 : df2ef410 r5 : 00000000 r4 : df2c3010
r3 : 00000000 r2 : 00000000 r1 : df86b0a0 r0 : 00000000
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 10c53c7d Table: 2f29404a DAC: 00000015
Process kworker/u2:0 (pid: 6, stack limit = 0xdf882240)
Stack: (0xdf883b50 to 0xdf884000)
...
Backtrace:
[<c03cacdc>] (usb_remove_hcd+0x0/0x150) from [<c03e88e4>] (host_stop+0x1c/0x3c)
r6:df2ef410 r5:00000000 r4:df2c3010
[<c03e88c8>] (host_stop+0x0/0x3c) from [<c03e8aa0>] (ci_hdrc_host_destroy+0x1c/0x20)
r5:00000000 r4:df2c3010
[<c03e8a84>] (ci_hdrc_host_destroy+0x0/0x20) from [<c03e7c80>] (ci_hdrc_probe+0x3ac/0x670)
[<c03e78d4>] (ci_hdrc_probe+0x0/0x670) from [<c0311044>] (platform_drv_probe+0x20/0x24)
[<c0311024>] (platform_drv_probe+0x0/0x24) from [<c030fcac>] (driver_probe_device+0x9c/0x234)
[<c030fc10>] (driver_probe_device+0x0/0x234) from [<c030ff28>] (__device_attach+0x44/0x48)
...
---[ end trace c88ccaf3969e8423 ]---
Fix this so at least we can continue booting and get to a shell prompt.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jingoo Han [Wed, 16 Oct 2013 16:28:16 +0000 (21:58 +0530)]
video: exynos_dp: Use the generic PHY driver
Use the generic PHY API to control the DP PHY.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Reviewed-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jingoo Han [Wed, 16 Oct 2013 16:28:15 +0000 (21:58 +0530)]
video: exynos_dp: remove non-DT support for Exynos Display Port
Exynos Display Port can be used only for Exynos SoCs. In addition,
non-DT for EXYNOS SoCs is not supported from v3.11; thus, there is
no need to support non-DT for Exynos Display Port.
The 'include/video/exynos_dp.h' file has been used for non-DT
support and the content of file include/video/exynos_dp.h is moved
to drivers/video/exynos/exynos_dp_core.h. Thus, the 'exynos_dp.h'
file is removed. Also, 'struct exynos_dp_platdata' is removed,
because it is not used any more.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Reviewed-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Generic PHY drivers are used to handle the MIPI CSIS and MIPI DSIM
DPHYs so we can remove now unused code at arch/arm/plat-samsung.
In case there is any board file for S5PV210 platforms using MIPI
CSIS/DSIM (not any upstream currently) it should use the generic
PHY API to bind the PHYs to respective PHY consumer drivers and
a platform device for the PHY provider should be defined.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Felipe Balbi <balbi@ti.com> Acked-by: Kukjin Kim <kgene.kim@samsung.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
video: exynos_mipi_dsim: Use the generic PHY driver
Use the generic PHY API instead of the platform callback
for the MIPI DSIM DPHY enable/reset control.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Felipe Balbi <balbi@ti.com> Acked-by: Donghwa Lee <dh09.lee@samsung.com> Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / ~andy / linux / log