From: Daniel Kurtz Date: Tue, 27 Mar 2012 18:36:12 +0000 (+0800) Subject: drm/i915/intel_i2c: assign HDMI port D to pin pair 6 X-Git-Tag: drm-intel-next-2012-04-09~51 X-Git-Url: http://pileus.org/git/?a=commitdiff_plain;h=e4fd17af6156b46fae3f9115830e1a35a62cd8e7;p=~andy%2Flinux drm/i915/intel_i2c: assign HDMI port D to pin pair 6 According to i915 documentation [1], "Port D" (DP/HDMI Port D) is actually gmbus pin pair 6 (gmbus0.2:0 == 110b GPIOF), not 7 (111b). Pin pair 7 is a reserved pair. [1] Documentation for [DevSNB+] and [DevIBX], as found on http://intellinuxgraphics.org: [DevSNB+]: http://intellinuxgraphics.org/documentation/SNB/IHD_OS_Vol3_Part3.pdf Section 2.2.2 lists the 6 gmbus ports (gpio pin pairs): [ 5: HDMI/DPD, 4: HDMIB, 3: HDMI/DPC, 2: LVDS, 1: SSC, 0: VGA ] 2.2.2.1 lists the GPIO registers to control these 6 ports. 2.2.3.1 lists the mapping between 5 of these gmbus ports and the 3 Pin_Pair_Select bits (of the GMBUS0 register). This table is missing HDMIB (port 101). [DevIBX]: http://intellinuxgraphics.org/IHD_OS_Vol3_Part3r2.pdf Section 2.2.2 lists the same 6 gmbus ports plus two 'reserved' gpio ports. 2.2.2.1 lists 8 GPIO registers... however, it says the size of the block is 6x32, which implies that those 2 reserved GPIO registers (GPIO_6 & GPIO_7) don't actually exist (or are irrelevant). 2.2.3.1 lists the mapping between the 6 named gmbus ports and the 3 Pin_Pair_Select bits (of the GMBUS0 register). This table has HDMIB. Note: the "reserved" and "disabled" pairs do not actually map to a physical pair of pins, nor GPIO regs and shouldn't be initialized or used. Fixing this is left for a later patch. This bug had not been noticed earlier for two reasons: 1) Until recently, "gmbus" mode was disabled - all transfers actually used "bit-bang" mode on GPIO port 5 (the "HDMI/DPD CTLDATA/CLK" pair), at register 0x5024 (defined as GPIOF i915_reg.h). Since this is the correct pair of pins for HDMI1, transfers succeed. 2) Even if gmbus mode is re-enabled, the first attempted transaction will fail because it tries to use the wrong ("Reserved") pin pair. However, the driver immediately falls back again to the bit-bang method, which correctly uses GPIOF, so again, transfers succeed. However, if gmbus mode is re-enabled and the GPIO fall-back mode is disabled, then reading an attached monitor's EDID fail. Signed-off-by: Daniel Kurtz Reviewed-by: Daniel Vetter Signed-off-by: Daniel Vetter --- diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h index f3609f260e5..accd8ee48f9 100644 --- a/drivers/gpu/drm/i915/i915_reg.h +++ b/drivers/gpu/drm/i915/i915_reg.h @@ -742,9 +742,9 @@ #define GMBUS_PORT_PANEL 3 #define GMBUS_PORT_DPC 4 /* HDMIC */ #define GMBUS_PORT_DPB 5 /* SDVO, HDMIB */ - /* 6 reserved */ -#define GMBUS_PORT_DPD 7 /* HDMID */ -#define GMBUS_NUM_PORTS 8 +#define GMBUS_PORT_DPD 6 /* HDMID */ +#define GMBUS_PORT_RESERVED 7 /* 7 reserved */ +#define GMBUS_NUM_PORTS 8 #define GMBUS1 0x5104 /* command/status */ #define GMBUS_SW_CLR_INT (1<<31) #define GMBUS_SW_RDY (1<<30) diff --git a/drivers/gpu/drm/i915/intel_i2c.c b/drivers/gpu/drm/i915/intel_i2c.c index e6c090bff9f..9347281633f 100644 --- a/drivers/gpu/drm/i915/intel_i2c.c +++ b/drivers/gpu/drm/i915/intel_i2c.c @@ -148,8 +148,8 @@ intel_gpio_setup(struct intel_gmbus *bus, u32 pin) GPIOC, GPIOD, GPIOE, - 0, GPIOF, + 0, }; struct i2c_algo_bit_data *algo; @@ -385,8 +385,8 @@ int intel_setup_gmbus(struct drm_device *dev) "panel", "dpc", "dpb", - "reserved", "dpd", + "reserved", }; struct drm_i915_private *dev_priv = dev->dev_private; int ret, i;