* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6: (25 commits)
avr32: Add hardware power-down function call
avr32: add include/asm-avr32/serial.h
avr32: don't offer PARPORT_PC
avr32: don't offer CONFIG_GEN_RTC
avr32: don't offer CONFIG_RTC
add include/asm-avr32/xor.h
avr32: Remove two unused #defines from mm/init.c
avr32: Implement set_rate(), set_parent() and mode() for pll1
avr32: Generic clockevents support
avr32: Move sleep code into mach-at32ap
avr32: Use constants from sysreg.h in asm.h
avr32: Delete mostly unused header asm/intc.h
avr32: start clocksource cleanup
avr32: pass i2c board info through at32_add_device_twi
avr32: cleanup - use _AC macro to define PAGE_SIZE
Generate raw keyboard codes for AVR32 architecture
atmel_usba_udc: Add support for AT91CAP9 UDPHS
atmel_usba_udc: Add missing kfree() in usba_udc_remove()
atmel_usba_udc: move endpoint declarations into platform data.
atmel_usba_udc: Kill GPIO_PIN_NONE
...
config GENERIC_TIME
def_bool y
+config GENERIC_CLOCKEVENTS
+ def_bool y
+
config RWSEM_XCHGADD_ALGORITHM
def_bool n
menu "System Type and features"
+source "kernel/time/Kconfig"
+
config SUBARCH_AVR32B
bool
config MMU
.section .irq.text,"ax",@progbits
-.global cpu_idle_sleep
-cpu_idle_sleep:
- mask_interrupts
- get_thread_info r8
- ld.w r9, r8[TI_flags]
- bld r9, TIF_NEED_RESCHED
- brcs cpu_idle_enable_int_and_exit
- sbr r9, TIF_CPU_GOING_TO_SLEEP
- st.w r8[TI_flags], r9
- unmask_interrupts
- sleep 0
-cpu_idle_skip_sleep:
- mask_interrupts
- ld.w r9, r8[TI_flags]
- cbr r9, TIF_CPU_GOING_TO_SLEEP
- st.w r8[TI_flags], r9
-cpu_idle_enable_int_and_exit:
- unmask_interrupts
- retal r12
-
.global irq_level0
.global irq_level1
.global irq_level2
#include <asm/sysreg.h>
#include <asm/ocd.h>
+#include <asm/arch/pm.h>
+
void (*pm_power_off)(void) = NULL;
EXPORT_SYMBOL(pm_power_off);
-extern void cpu_idle_sleep(void);
-
/*
* This file handles the architecture-dependent parts of process handling..
*/
void machine_power_off(void)
{
+ if (pm_power_off)
+ pm_power_off();
}
void machine_restart(char *cmd)
/*
* Copyright (C) 2004-2007 Atmel Corporation
*
- * Based on MIPS implementation arch/mips/kernel/time.c
- * Copyright 2001 MontaVista Software Inc.
- *
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
#include <linux/clk.h>
-#include <linux/clocksource.h>
+#include <linux/clockchips.h>
#include <linux/time.h>
#include <linux/module.h>
#include <linux/interrupt.h>
#include <asm/io.h>
#include <asm/sections.h>
-/* how many counter cycles in a jiffy? */
-static u32 cycles_per_jiffy;
+#include <asm/arch/pm.h>
-/* the count value for the next timer interrupt */
-static u32 expirelo;
-cycle_t __weak read_cycle_count(void)
+static cycle_t read_cycle_count(void)
{
return (cycle_t)sysreg_read(COUNT);
}
-struct clocksource __weak clocksource_avr32 = {
- .name = "avr32",
- .rating = 350,
+/*
+ * The architectural cycle count registers are a fine clocksource unless
+ * the system idle loop use sleep states like "idle": the CPU cycles
+ * measured by COUNT (and COMPARE) don't happen during sleep states.
+ * Their duration also changes if cpufreq changes the CPU clock rate.
+ * So we rate the clocksource using COUNT as very low quality.
+ */
+static struct clocksource counter = {
+ .name = "avr32_counter",
+ .rating = 50,
.read = read_cycle_count,
.mask = CLOCKSOURCE_MASK(32),
.shift = 16,
.flags = CLOCK_SOURCE_IS_CONTINUOUS,
};
-irqreturn_t __weak timer_interrupt(int irq, void *dev_id);
-
-struct irqaction timer_irqaction = {
- .handler = timer_interrupt,
- .flags = IRQF_DISABLED,
- .name = "timer",
-};
-
-/*
- * By default we provide the null RTC ops
- */
-static unsigned long null_rtc_get_time(void)
+static irqreturn_t timer_interrupt(int irq, void *dev_id)
{
- return mktime(2007, 1, 1, 0, 0, 0);
-}
-
-static int null_rtc_set_time(unsigned long sec)
-{
- return 0;
-}
+ struct clock_event_device *evdev = dev_id;
-static unsigned long (*rtc_get_time)(void) = null_rtc_get_time;
-static int (*rtc_set_time)(unsigned long) = null_rtc_set_time;
-
-static void avr32_timer_ack(void)
-{
- u32 count;
-
- /* Ack this timer interrupt and set the next one */
- expirelo += cycles_per_jiffy;
- /* setting COMPARE to 0 stops the COUNT-COMPARE */
- if (expirelo == 0) {
- sysreg_write(COMPARE, expirelo + 1);
- } else {
- sysreg_write(COMPARE, expirelo);
- }
+ /*
+ * Disable the interrupt until the clockevent subsystem
+ * reprograms it.
+ */
+ sysreg_write(COMPARE, 0);
- /* Check to see if we have missed any timer interrupts */
- count = sysreg_read(COUNT);
- if ((count - expirelo) < 0x7fffffff) {
- expirelo = count + cycles_per_jiffy;
- sysreg_write(COMPARE, expirelo);
- }
+ evdev->event_handler(evdev);
+ return IRQ_HANDLED;
}
-int __weak avr32_hpt_init(void)
-{
- int ret;
- unsigned long mult, shift, count_hz;
-
- count_hz = clk_get_rate(boot_cpu_data.clk);
- shift = clocksource_avr32.shift;
- mult = clocksource_hz2mult(count_hz, shift);
- clocksource_avr32.mult = mult;
-
- {
- u64 tmp;
-
- tmp = TICK_NSEC;
- tmp <<= shift;
- tmp += mult / 2;
- do_div(tmp, mult);
-
- cycles_per_jiffy = tmp;
- }
+static struct irqaction timer_irqaction = {
+ .handler = timer_interrupt,
+ .flags = IRQF_TIMER | IRQF_DISABLED,
+ .name = "avr32_comparator",
+};
- ret = setup_irq(0, &timer_irqaction);
- if (ret) {
- pr_debug("timer: could not request IRQ 0: %d\n", ret);
- return -ENODEV;
- }
+static int comparator_next_event(unsigned long delta,
+ struct clock_event_device *evdev)
+{
+ unsigned long flags;
- printk(KERN_INFO "timer: AT32AP COUNT-COMPARE at irq 0, "
- "%lu.%03lu MHz\n",
- ((count_hz + 500) / 1000) / 1000,
- ((count_hz + 500) / 1000) % 1000);
+ raw_local_irq_save(flags);
- return 0;
-}
+ /* The time to read COUNT then update COMPARE must be less
+ * than the min_delta_ns value for this clockevent source.
+ */
+ sysreg_write(COMPARE, (sysreg_read(COUNT) + delta) ? : 1);
-/*
- * Taken from MIPS c0_hpt_timer_init().
- *
- * The reason COUNT is written twice is probably to make sure we don't get any
- * timer interrupts while we are messing with the counter.
- */
-int __weak avr32_hpt_start(void)
-{
- u32 count = sysreg_read(COUNT);
- expirelo = (count / cycles_per_jiffy + 1) * cycles_per_jiffy;
- sysreg_write(COUNT, expirelo - cycles_per_jiffy);
- sysreg_write(COMPARE, expirelo);
- sysreg_write(COUNT, count);
+ raw_local_irq_restore(flags);
return 0;
}
-/*
- * local_timer_interrupt() does profiling and process accounting on a
- * per-CPU basis.
- *
- * In UP mode, it is invoked from the (global) timer_interrupt.
- */
-void local_timer_interrupt(int irq, void *dev_id)
+static void comparator_mode(enum clock_event_mode mode,
+ struct clock_event_device *evdev)
{
- if (current->pid)
- profile_tick(CPU_PROFILING);
- update_process_times(user_mode(get_irq_regs()));
+ switch (mode) {
+ case CLOCK_EVT_MODE_ONESHOT:
+ pr_debug("%s: start\n", evdev->name);
+ /* FALLTHROUGH */
+ case CLOCK_EVT_MODE_RESUME:
+ cpu_disable_idle_sleep();
+ break;
+ case CLOCK_EVT_MODE_UNUSED:
+ case CLOCK_EVT_MODE_SHUTDOWN:
+ sysreg_write(COMPARE, 0);
+ pr_debug("%s: stop\n", evdev->name);
+ cpu_enable_idle_sleep();
+ break;
+ default:
+ BUG();
+ }
}
-irqreturn_t __weak timer_interrupt(int irq, void *dev_id)
-{
- /* ack timer interrupt and try to set next interrupt */
- avr32_timer_ack();
-
- /*
- * Call the generic timer interrupt handler
- */
- write_seqlock(&xtime_lock);
- do_timer(1);
- write_sequnlock(&xtime_lock);
-
- /*
- * In UP mode, we call local_timer_interrupt() to do profiling
- * and process accounting.
- *
- * SMP is not supported yet.
- */
- local_timer_interrupt(irq, dev_id);
-
- return IRQ_HANDLED;
-}
+static struct clock_event_device comparator = {
+ .name = "avr32_comparator",
+ .features = CLOCK_EVT_FEAT_ONESHOT,
+ .shift = 16,
+ .rating = 50,
+ .cpumask = CPU_MASK_CPU0,
+ .set_next_event = comparator_next_event,
+ .set_mode = comparator_mode,
+};
void __init time_init(void)
{
+ unsigned long counter_hz;
int ret;
- /*
- * Make sure we don't get any COMPARE interrupts before we can
- * handle them.
- */
- sysreg_write(COMPARE, 0);
-
- xtime.tv_sec = rtc_get_time();
+ xtime.tv_sec = mktime(2007, 1, 1, 0, 0, 0);
xtime.tv_nsec = 0;
set_normalized_timespec(&wall_to_monotonic,
-xtime.tv_sec, -xtime.tv_nsec);
- ret = avr32_hpt_init();
- if (ret) {
- pr_debug("timer: failed setup: %d\n", ret);
- return;
- }
+ /* figure rate for counter */
+ counter_hz = clk_get_rate(boot_cpu_data.clk);
+ counter.mult = clocksource_hz2mult(counter_hz, counter.shift);
- ret = clocksource_register(&clocksource_avr32);
+ ret = clocksource_register(&counter);
if (ret)
pr_debug("timer: could not register clocksource: %d\n", ret);
- ret = avr32_hpt_start();
- if (ret) {
- pr_debug("timer: failed starting: %d\n", ret);
- return;
- }
-}
+ /* setup COMPARE clockevent */
+ comparator.mult = div_sc(counter_hz, NSEC_PER_SEC, comparator.shift);
+ comparator.max_delta_ns = clockevent_delta2ns((u32)~0, &comparator);
+ comparator.min_delta_ns = clockevent_delta2ns(50, &comparator) + 1;
-static struct sysdev_class timer_class = {
- .name = "timer",
-};
+ sysreg_write(COMPARE, 0);
+ timer_irqaction.dev_id = &comparator;
-static struct sys_device timer_device = {
- .id = 0,
- .cls = &timer_class,
-};
+ ret = setup_irq(0, &timer_irqaction);
+ if (ret)
+ pr_debug("timer: could not request IRQ 0: %d\n", ret);
+ else {
+ clockevents_register_device(&comparator);
-static int __init init_timer_sysfs(void)
-{
- int err = sysdev_class_register(&timer_class);
- if (!err)
- err = sysdev_register(&timer_device);
- return err;
+ pr_info("%s: irq 0, %lu.%03lu MHz\n", comparator.name,
+ ((counter_hz + 500) / 1000) / 1000,
+ ((counter_hz + 500) / 1000) % 1000);
+ }
}
-
-device_initcall(init_timer_sysfs);
obj-y += at32ap.o clock.o intc.o extint.o pio.o hsmc.o
-obj-$(CONFIG_CPU_AT32AP700X) += at32ap700x.o
-obj-$(CONFIG_CPU_AT32AP700X) += time-tc.o
+obj-$(CONFIG_CPU_AT32AP700X) += at32ap700x.o pm-at32ap700x.o
obj-$(CONFIG_CPU_FREQ_AT32AP) += cpufreq.o
* published by the Free Software Foundation.
*/
#include <linux/clk.h>
+#include <linux/delay.h>
#include <linux/fb.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/dma-mapping.h>
#include <linux/spi/spi.h>
+#include <linux/usb/atmel_usba_udc.h>
#include <asm/io.h>
#include <asm/irq.h>
[2] = 12000000,
};
+static struct clk osc0;
+static struct clk osc1;
+
static unsigned long osc_get_rate(struct clk *clk)
{
return at32ap7000_osc_rates[clk->index];
{
unsigned long div, mul, rate;
- if (!(control & PM_BIT(PLLEN)))
- return 0;
-
div = PM_BFEXT(PLLDIV, control) + 1;
mul = PM_BFEXT(PLLMUL, control) + 1;
return rate;
}
+static long pll_set_rate(struct clk *clk, unsigned long rate,
+ u32 *pll_ctrl)
+{
+ unsigned long mul;
+ unsigned long mul_best_fit = 0;
+ unsigned long div;
+ unsigned long div_min;
+ unsigned long div_max;
+ unsigned long div_best_fit = 0;
+ unsigned long base;
+ unsigned long pll_in;
+ unsigned long actual = 0;
+ unsigned long rate_error;
+ unsigned long rate_error_prev = ~0UL;
+ u32 ctrl;
+
+ /* Rate must be between 80 MHz and 200 Mhz. */
+ if (rate < 80000000UL || rate > 200000000UL)
+ return -EINVAL;
+
+ ctrl = PM_BF(PLLOPT, 4);
+ base = clk->parent->get_rate(clk->parent);
+
+ /* PLL input frequency must be between 6 MHz and 32 MHz. */
+ div_min = DIV_ROUND_UP(base, 32000000UL);
+ div_max = base / 6000000UL;
+
+ if (div_max < div_min)
+ return -EINVAL;
+
+ for (div = div_min; div <= div_max; div++) {
+ pll_in = (base + div / 2) / div;
+ mul = (rate + pll_in / 2) / pll_in;
+
+ if (mul == 0)
+ continue;
+
+ actual = pll_in * mul;
+ rate_error = abs(actual - rate);
+
+ if (rate_error < rate_error_prev) {
+ mul_best_fit = mul;
+ div_best_fit = div;
+ rate_error_prev = rate_error;
+ }
+
+ if (rate_error == 0)
+ break;
+ }
+
+ if (div_best_fit == 0)
+ return -EINVAL;
+
+ ctrl |= PM_BF(PLLMUL, mul_best_fit - 1);
+ ctrl |= PM_BF(PLLDIV, div_best_fit - 1);
+ ctrl |= PM_BF(PLLCOUNT, 16);
+
+ if (clk->parent == &osc1)
+ ctrl |= PM_BIT(PLLOSC);
+
+ *pll_ctrl = ctrl;
+
+ return actual;
+}
+
static unsigned long pll0_get_rate(struct clk *clk)
{
u32 control;
return pll_get_rate(clk, control);
}
+static void pll1_mode(struct clk *clk, int enabled)
+{
+ unsigned long timeout;
+ u32 status;
+ u32 ctrl;
+
+ ctrl = pm_readl(PLL1);
+
+ if (enabled) {
+ if (!PM_BFEXT(PLLMUL, ctrl) && !PM_BFEXT(PLLDIV, ctrl)) {
+ pr_debug("clk %s: failed to enable, rate not set\n",
+ clk->name);
+ return;
+ }
+
+ ctrl |= PM_BIT(PLLEN);
+ pm_writel(PLL1, ctrl);
+
+ /* Wait for PLL lock. */
+ for (timeout = 10000; timeout; timeout--) {
+ status = pm_readl(ISR);
+ if (status & PM_BIT(LOCK1))
+ break;
+ udelay(10);
+ }
+
+ if (!(status & PM_BIT(LOCK1)))
+ printk(KERN_ERR "clk %s: timeout waiting for lock\n",
+ clk->name);
+ } else {
+ ctrl &= ~PM_BIT(PLLEN);
+ pm_writel(PLL1, ctrl);
+ }
+}
+
static unsigned long pll1_get_rate(struct clk *clk)
{
u32 control;
return pll_get_rate(clk, control);
}
+static long pll1_set_rate(struct clk *clk, unsigned long rate, int apply)
+{
+ u32 ctrl = 0;
+ unsigned long actual_rate;
+
+ actual_rate = pll_set_rate(clk, rate, &ctrl);
+
+ if (apply) {
+ if (actual_rate != rate)
+ return -EINVAL;
+ if (clk->users > 0)
+ return -EBUSY;
+ pr_debug(KERN_INFO "clk %s: new rate %lu (actual rate %lu)\n",
+ clk->name, rate, actual_rate);
+ pm_writel(PLL1, ctrl);
+ }
+
+ return actual_rate;
+}
+
+static int pll1_set_parent(struct clk *clk, struct clk *parent)
+{
+ u32 ctrl;
+
+ if (clk->users > 0)
+ return -EBUSY;
+
+ ctrl = pm_readl(PLL1);
+ WARN_ON(ctrl & PM_BIT(PLLEN));
+
+ if (parent == &osc0)
+ ctrl &= ~PM_BIT(PLLOSC);
+ else if (parent == &osc1)
+ ctrl |= PM_BIT(PLLOSC);
+ else
+ return -EINVAL;
+
+ pm_writel(PLL1, ctrl);
+ clk->parent = parent;
+
+ return 0;
+}
+
/*
* The AT32AP7000 has five primary clock sources: One 32kHz
* oscillator, two crystal oscillators and two PLLs.
};
static struct clk pll1 = {
.name = "pll1",
+ .mode = pll1_mode,
.get_rate = pll1_get_rate,
+ .set_rate = pll1_set_rate,
+ .set_parent = pll1_set_parent,
.parent = &osc0,
};
}
/* --------------------------------------------------------------------
- * System Timer/Counter (TC)
+ * Timer/Counter (TC)
* -------------------------------------------------------------------- */
-static struct resource at32_systc0_resource[] = {
+
+static struct resource at32_tcb0_resource[] = {
PBMEM(0xfff00c00),
IRQ(22),
};
-struct platform_device at32_systc0_device = {
- .name = "systc",
+static struct platform_device at32_tcb0_device = {
+ .name = "atmel_tcb",
.id = 0,
- .resource = at32_systc0_resource,
- .num_resources = ARRAY_SIZE(at32_systc0_resource),
+ .resource = at32_tcb0_resource,
+ .num_resources = ARRAY_SIZE(at32_tcb0_resource),
};
-DEV_CLK(pclk, at32_systc0, pbb, 3);
+DEV_CLK(t0_clk, at32_tcb0, pbb, 3);
+
+static struct resource at32_tcb1_resource[] = {
+ PBMEM(0xfff01000),
+ IRQ(23),
+};
+static struct platform_device at32_tcb1_device = {
+ .name = "atmel_tcb",
+ .id = 1,
+ .resource = at32_tcb1_resource,
+ .num_resources = ARRAY_SIZE(at32_tcb1_resource),
+};
+DEV_CLK(t0_clk, at32_tcb1, pbb, 4);
/* --------------------------------------------------------------------
* PIO
platform_device_register(&pdc_device);
platform_device_register(&dmaca0_device);
- platform_device_register(&at32_systc0_device);
+ platform_device_register(&at32_tcb0_device);
+ platform_device_register(&at32_tcb1_device);
platform_device_register(&pio0_device);
platform_device_register(&pio1_device);
.index = 2,
};
-struct platform_device *__init at32_add_device_twi(unsigned int id)
+struct platform_device *__init at32_add_device_twi(unsigned int id,
+ struct i2c_board_info *b,
+ unsigned int n)
{
struct platform_device *pdev;
atmel_twi0_pclk.dev = &pdev->dev;
+ if (b)
+ i2c_register_board_info(id, b, n);
+
platform_device_add(pdev);
return pdev;
.index = 6,
};
+#define EP(nam, idx, maxpkt, maxbk, dma, isoc) \
+ [idx] = { \
+ .name = nam, \
+ .index = idx, \
+ .fifo_size = maxpkt, \
+ .nr_banks = maxbk, \
+ .can_dma = dma, \
+ .can_isoc = isoc, \
+ }
+
+static struct usba_ep_data at32_usba_ep[] __initdata = {
+ EP("ep0", 0, 64, 1, 0, 0),
+ EP("ep1", 1, 512, 2, 1, 1),
+ EP("ep2", 2, 512, 2, 1, 1),
+ EP("ep3-int", 3, 64, 3, 1, 0),
+ EP("ep4-int", 4, 64, 3, 1, 0),
+ EP("ep5", 5, 1024, 3, 1, 1),
+ EP("ep6", 6, 1024, 3, 1, 1),
+};
+
+#undef EP
+
struct platform_device *__init
at32_add_device_usba(unsigned int id, struct usba_platform_data *data)
{
+ /*
+ * pdata doesn't have room for any endpoints, so we need to
+ * append room for the ones we need right after it.
+ */
+ struct {
+ struct usba_platform_data pdata;
+ struct usba_ep_data ep[7];
+ } usba_data;
struct platform_device *pdev;
if (id != 0)
ARRAY_SIZE(usba0_resource)))
goto out_free_pdev;
- if (data) {
- if (platform_device_add_data(pdev, data, sizeof(*data)))
- goto out_free_pdev;
+ if (data)
+ usba_data.pdata.vbus_pin = data->vbus_pin;
+ else
+ usba_data.pdata.vbus_pin = -EINVAL;
+
+ data = &usba_data.pdata;
+ data->num_ep = ARRAY_SIZE(at32_usba_ep);
+ memcpy(data->ep, at32_usba_ep, sizeof(at32_usba_ep));
- if (data->vbus_pin != GPIO_PIN_NONE)
- at32_select_gpio(data->vbus_pin, 0);
- }
+ if (platform_device_add_data(pdev, data, sizeof(usba_data)))
+ goto out_free_pdev;
+
+ if (data->vbus_pin >= 0)
+ at32_select_gpio(data->vbus_pin, 0);
usba0_pclk.dev = &pdev->dev;
usba0_hclk.dev = &pdev->dev;
&pio2_mck,
&pio3_mck,
&pio4_mck,
- &at32_systc0_pclk,
+ &at32_tcb0_t0_clk,
+ &at32_tcb1_t0_clk,
&atmel_usart0_usart,
&atmel_usart1_usart,
&atmel_usart2_usart,
#include <linux/irq.h>
#include <linux/platform_device.h>
-#include <asm/intc.h>
#include <asm/io.h>
#include "intc.h"
--- /dev/null
+/*
+ * Low-level Power Management code.
+ *
+ * Copyright (C) 2008 Atmel Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <asm/asm.h>
+#include <asm/asm-offsets.h>
+#include <asm/thread_info.h>
+#include <asm/arch/pm.h>
+
+ .section .bss, "wa", @nobits
+ .global disable_idle_sleep
+ .type disable_idle_sleep, @object
+disable_idle_sleep:
+ .int 4
+ .size disable_idle_sleep, . - disable_idle_sleep
+
+ /* Keep this close to the irq handlers */
+ .section .irq.text, "ax", @progbits
+
+ /*
+ * void cpu_enter_idle(void)
+ *
+ * Put the CPU into "idle" mode, in which it will consume
+ * significantly less power.
+ *
+ * If an interrupt comes along in the window between
+ * unmask_interrupts and the sleep instruction below, the
+ * interrupt code will adjust the return address so that we
+ * never execute the sleep instruction. This is required
+ * because the AP7000 doesn't unmask interrupts when entering
+ * sleep modes; later CPUs may not need this workaround.
+ */
+ .global cpu_enter_idle
+ .type cpu_enter_idle, @function
+cpu_enter_idle:
+ mask_interrupts
+ get_thread_info r8
+ ld.w r9, r8[TI_flags]
+ bld r9, TIF_NEED_RESCHED
+ brcs .Lret_from_sleep
+ sbr r9, TIF_CPU_GOING_TO_SLEEP
+ st.w r8[TI_flags], r9
+ unmask_interrupts
+ sleep CPU_SLEEP_IDLE
+ .size cpu_idle_sleep, . - cpu_idle_sleep
+
+ /*
+ * Common return path for PM functions that don't run from
+ * SRAM.
+ */
+ .global cpu_idle_skip_sleep
+ .type cpu_idle_skip_sleep, @function
+cpu_idle_skip_sleep:
+ mask_interrupts
+ ld.w r9, r8[TI_flags]
+ cbr r9, TIF_CPU_GOING_TO_SLEEP
+ st.w r8[TI_flags], r9
+.Lret_from_sleep:
+ unmask_interrupts
+ retal r12
+ .size cpu_idle_skip_sleep, . - cpu_idle_skip_sleep
+++ /dev/null
-/*
- * Copyright (C) 2004-2007 Atmel Corporation
- *
- * Based on MIPS implementation arch/mips/kernel/time.c
- * Copyright 2001 MontaVista Software Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/clk.h>
-#include <linux/clocksource.h>
-#include <linux/time.h>
-#include <linux/module.h>
-#include <linux/interrupt.h>
-#include <linux/irq.h>
-#include <linux/kernel_stat.h>
-#include <linux/errno.h>
-#include <linux/init.h>
-#include <linux/profile.h>
-#include <linux/sysdev.h>
-#include <linux/err.h>
-
-#include <asm/div64.h>
-#include <asm/sysreg.h>
-#include <asm/io.h>
-#include <asm/sections.h>
-
-#include <asm/arch/time.h>
-
-/* how many counter cycles in a jiffy? */
-static u32 cycles_per_jiffy;
-
-/* the count value for the next timer interrupt */
-static u32 expirelo;
-
-/* the I/O registers of the TC module */
-static void __iomem *ioregs;
-
-cycle_t read_cycle_count(void)
-{
- return (cycle_t)timer_read(ioregs, 0, CV);
-}
-
-struct clocksource clocksource_avr32 = {
- .name = "avr32",
- .rating = 342,
- .read = read_cycle_count,
- .mask = CLOCKSOURCE_MASK(16),
- .shift = 16,
- .flags = CLOCK_SOURCE_IS_CONTINUOUS,
-};
-
-static void avr32_timer_ack(void)
-{
- u16 count = expirelo;
-
- /* Ack this timer interrupt and set the next one, use a u16
- * variable so it will wrap around correctly */
- count += cycles_per_jiffy;
- expirelo = count;
- timer_write(ioregs, 0, RC, expirelo);
-
- /* Check to see if we have missed any timer interrupts */
- count = timer_read(ioregs, 0, CV);
- if ((count - expirelo) < 0x7fff) {
- expirelo = count + cycles_per_jiffy;
- timer_write(ioregs, 0, RC, expirelo);
- }
-}
-
-u32 avr32_hpt_read(void)
-{
- return timer_read(ioregs, 0, CV);
-}
-
-static int avr32_timer_calc_div_and_set_jiffies(struct clk *pclk)
-{
- unsigned int cycles_max = (clocksource_avr32.mask + 1) / 2;
- unsigned int divs[] = { 4, 8, 16, 32 };
- int divs_size = ARRAY_SIZE(divs);
- int i = 0;
- unsigned long count_hz;
- unsigned long shift;
- unsigned long mult;
- int clock_div = -1;
- u64 tmp;
-
- shift = clocksource_avr32.shift;
-
- do {
- count_hz = clk_get_rate(pclk) / divs[i];
- mult = clocksource_hz2mult(count_hz, shift);
- clocksource_avr32.mult = mult;
-
- tmp = TICK_NSEC;
- tmp <<= shift;
- tmp += mult / 2;
- do_div(tmp, mult);
-
- cycles_per_jiffy = tmp;
- } while (cycles_per_jiffy > cycles_max && ++i < divs_size);
-
- clock_div = i + 1;
-
- if (clock_div > divs_size) {
- pr_debug("timer: could not calculate clock divider\n");
- return -EFAULT;
- }
-
- /* Set the clock divider */
- timer_write(ioregs, 0, CMR, TIMER_BF(CMR_TCCLKS, clock_div));
-
- return 0;
-}
-
-int avr32_hpt_init(unsigned int count)
-{
- struct resource *regs;
- struct clk *pclk;
- int irq = -1;
- int ret = 0;
-
- ret = -ENXIO;
-
- irq = platform_get_irq(&at32_systc0_device, 0);
- if (irq < 0) {
- pr_debug("timer: could not get irq\n");
- goto out_error;
- }
-
- pclk = clk_get(&at32_systc0_device.dev, "pclk");
- if (IS_ERR(pclk)) {
- pr_debug("timer: could not get clk: %ld\n", PTR_ERR(pclk));
- goto out_error;
- }
- clk_enable(pclk);
-
- regs = platform_get_resource(&at32_systc0_device, IORESOURCE_MEM, 0);
- if (!regs) {
- pr_debug("timer: could not get resource\n");
- goto out_error_clk;
- }
-
- ioregs = ioremap(regs->start, regs->end - regs->start + 1);
- if (!ioregs) {
- pr_debug("timer: could not get ioregs\n");
- goto out_error_clk;
- }
-
- ret = avr32_timer_calc_div_and_set_jiffies(pclk);
- if (ret)
- goto out_error_io;
-
- ret = setup_irq(irq, &timer_irqaction);
- if (ret) {
- pr_debug("timer: could not request irq %d: %d\n",
- irq, ret);
- goto out_error_io;
- }
-
- expirelo = (timer_read(ioregs, 0, CV) / cycles_per_jiffy + 1)
- * cycles_per_jiffy;
-
- /* Enable clock and interrupts on RC compare */
- timer_write(ioregs, 0, CCR, TIMER_BIT(CCR_CLKEN));
- timer_write(ioregs, 0, IER, TIMER_BIT(IER_CPCS));
- /* Set cycles to first interrupt */
- timer_write(ioregs, 0, RC, expirelo);
-
- printk(KERN_INFO "timer: AT32AP system timer/counter at 0x%p irq %d\n",
- ioregs, irq);
-
- return 0;
-
-out_error_io:
- iounmap(ioregs);
-out_error_clk:
- clk_put(pclk);
-out_error:
- return ret;
-}
-
-int avr32_hpt_start(void)
-{
- timer_write(ioregs, 0, CCR, TIMER_BIT(CCR_SWTRG));
- return 0;
-}
-
-irqreturn_t timer_interrupt(int irq, void *dev_id)
-{
- unsigned int sr = timer_read(ioregs, 0, SR);
-
- if (sr & TIMER_BIT(SR_CPCS)) {
- /* ack timer interrupt and try to set next interrupt */
- avr32_timer_ack();
-
- /*
- * Call the generic timer interrupt handler
- */
- write_seqlock(&xtime_lock);
- do_timer(1);
- write_sequnlock(&xtime_lock);
-
- /*
- * In UP mode, we call local_timer_interrupt() to do profiling
- * and process accounting.
- *
- * SMP is not supported yet.
- */
- local_timer_interrupt(irq, dev_id);
-
- return IRQ_HANDLED;
- }
-
- return IRQ_NONE;
-}
*/
unsigned long mmu_context_cache = NO_CONTEXT;
-#define START_PFN (NODE_DATA(0)->bdata->node_boot_start >> PAGE_SHIFT)
-#define MAX_LOW_PFN (NODE_DATA(0)->bdata->node_low_pfn)
-
void show_mem(void)
{
int total = 0, reserved = 0, cached = 0;
#include <linux/sched.h>
#include <linux/types.h>
-#include <asm/intc.h>
#include <asm/sysreg.h>
#include <asm/system.h>
config RTC
tristate "Enhanced Real Time Clock Support"
- depends on !PPC && !PARISC && !IA64 && !M68K && !SPARC && !FRV && !ARM && !SUPERH && !S390
+ depends on !PPC && !PARISC && !IA64 && !M68K && !SPARC && !FRV && !ARM && !SUPERH && !S390 && !AVR32
---help---
If you say Y here and create a character special file /dev/rtc with
major number 10 and minor number 135 using mknod ("man mknod"), you
config GEN_RTC
tristate "Generic /dev/rtc emulation"
- depends on RTC!=y && !IA64 && !ARM && !M32R && !MIPS && !SPARC && !FRV && !S390 && !SUPERH
+ depends on RTC!=y && !IA64 && !ARM && !M32R && !MIPS && !SPARC && !FRV && !S390 && !SUPERH && !AVR32
---help---
If you say Y here and create a character special file /dev/rtc with
major number 10 and minor number 135 using mknod ("man mknod"), you
#if defined(CONFIG_X86) || defined(CONFIG_IA64) || defined(CONFIG_ALPHA) ||\
defined(CONFIG_MIPS) || defined(CONFIG_PPC) || defined(CONFIG_SPARC) ||\
defined(CONFIG_PARISC) || defined(CONFIG_SUPERH) ||\
- (defined(CONFIG_ARM) && defined(CONFIG_KEYBOARD_ATKBD) && !defined(CONFIG_ARCH_RPC))
+ (defined(CONFIG_ARM) && defined(CONFIG_KEYBOARD_ATKBD) && !defined(CONFIG_ARCH_RPC)) ||\
+ defined(CONFIG_AVR32)
#define HW_RAW(dev) (test_bit(EV_MSC, dev->evbit) && test_bit(MSC_RAW, dev->mscbit) &&\
((dev)->id.bustype == BUS_I8042) && ((dev)->id.vendor == 0x0001) && ((dev)->id.product == 0x0001))
+obj-$(CONFIG_ATMEL_TCB_CLKSRC) += tcb_clksrc.o
obj-$(CONFIG_X86_CYCLONE_TIMER) += cyclone.o
obj-$(CONFIG_X86_PM_TIMER) += acpi_pm.o
obj-$(CONFIG_SCx200HR_TIMER) += scx200_hrt.o
--- /dev/null
+#include <linux/init.h>
+#include <linux/clocksource.h>
+#include <linux/clockchips.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/ioport.h>
+#include <linux/io.h>
+#include <linux/platform_device.h>
+#include <linux/atmel_tc.h>
+
+
+/*
+ * We're configured to use a specific TC block, one that's not hooked
+ * up to external hardware, to provide a time solution:
+ *
+ * - Two channels combine to create a free-running 32 bit counter
+ * with a base rate of 5+ MHz, packaged as a clocksource (with
+ * resolution better than 200 nsec).
+ *
+ * - The third channel may be used to provide a 16-bit clockevent
+ * source, used in either periodic or oneshot mode. This runs
+ * at 32 KiHZ, and can handle delays of up to two seconds.
+ *
+ * A boot clocksource and clockevent source are also currently needed,
+ * unless the relevant platforms (ARM/AT91, AVR32/AT32) are changed so
+ * this code can be used when init_timers() is called, well before most
+ * devices are set up. (Some low end AT91 parts, which can run uClinux,
+ * have only the timers in one TC block... they currently don't support
+ * the tclib code, because of that initialization issue.)
+ *
+ * REVISIT behavior during system suspend states... we should disable
+ * all clocks and save the power. Easily done for clockevent devices,
+ * but clocksources won't necessarily get the needed notifications.
+ * For deeper system sleep states, this will be mandatory...
+ */
+
+static void __iomem *tcaddr;
+
+static cycle_t tc_get_cycles(void)
+{
+ unsigned long flags;
+ u32 lower, upper;
+
+ raw_local_irq_save(flags);
+ do {
+ upper = __raw_readl(tcaddr + ATMEL_TC_REG(1, CV));
+ lower = __raw_readl(tcaddr + ATMEL_TC_REG(0, CV));
+ } while (upper != __raw_readl(tcaddr + ATMEL_TC_REG(1, CV)));
+
+ raw_local_irq_restore(flags);
+ return (upper << 16) | lower;
+}
+
+static struct clocksource clksrc = {
+ .name = "tcb_clksrc",
+ .rating = 200,
+ .read = tc_get_cycles,
+ .mask = CLOCKSOURCE_MASK(32),
+ .shift = 18,
+ .flags = CLOCK_SOURCE_IS_CONTINUOUS,
+};
+
+#ifdef CONFIG_GENERIC_CLOCKEVENTS
+
+struct tc_clkevt_device {
+ struct clock_event_device clkevt;
+ struct clk *clk;
+ void __iomem *regs;
+};
+
+static struct tc_clkevt_device *to_tc_clkevt(struct clock_event_device *clkevt)
+{
+ return container_of(clkevt, struct tc_clkevt_device, clkevt);
+}
+
+/* For now, we always use the 32K clock ... this optimizes for NO_HZ,
+ * because using one of the divided clocks would usually mean the
+ * tick rate can never be less than several dozen Hz (vs 0.5 Hz).
+ *
+ * A divided clock could be good for high resolution timers, since
+ * 30.5 usec resolution can seem "low".
+ */
+static u32 timer_clock;
+
+static void tc_mode(enum clock_event_mode m, struct clock_event_device *d)
+{
+ struct tc_clkevt_device *tcd = to_tc_clkevt(d);
+ void __iomem *regs = tcd->regs;
+
+ if (tcd->clkevt.mode == CLOCK_EVT_MODE_PERIODIC
+ || tcd->clkevt.mode == CLOCK_EVT_MODE_ONESHOT) {
+ __raw_writel(0xff, regs + ATMEL_TC_REG(2, IDR));
+ __raw_writel(ATMEL_TC_CLKDIS, regs + ATMEL_TC_REG(2, CCR));
+ clk_disable(tcd->clk);
+ }
+
+ switch (m) {
+
+ /* By not making the gentime core emulate periodic mode on top
+ * of oneshot, we get lower overhead and improved accuracy.
+ */
+ case CLOCK_EVT_MODE_PERIODIC:
+ clk_enable(tcd->clk);
+
+ /* slow clock, count up to RC, then irq and restart */
+ __raw_writel(timer_clock
+ | ATMEL_TC_WAVE | ATMEL_TC_WAVESEL_UP_AUTO,
+ regs + ATMEL_TC_REG(2, CMR));
+ __raw_writel((32768 + HZ/2) / HZ, tcaddr + ATMEL_TC_REG(2, RC));
+
+ /* Enable clock and interrupts on RC compare */
+ __raw_writel(ATMEL_TC_CPCS, regs + ATMEL_TC_REG(2, IER));
+
+ /* go go gadget! */
+ __raw_writel(ATMEL_TC_CLKEN | ATMEL_TC_SWTRG,
+ regs + ATMEL_TC_REG(2, CCR));
+ break;
+
+ case CLOCK_EVT_MODE_ONESHOT:
+ clk_enable(tcd->clk);
+
+ /* slow clock, count up to RC, then irq and stop */
+ __raw_writel(timer_clock | ATMEL_TC_CPCSTOP
+ | ATMEL_TC_WAVE | ATMEL_TC_WAVESEL_UP_AUTO,
+ regs + ATMEL_TC_REG(2, CMR));
+ __raw_writel(ATMEL_TC_CPCS, regs + ATMEL_TC_REG(2, IER));
+
+ /* set_next_event() configures and starts the timer */
+ break;
+
+ default:
+ break;
+ }
+}
+
+static int tc_next_event(unsigned long delta, struct clock_event_device *d)
+{
+ __raw_writel(delta, tcaddr + ATMEL_TC_REG(2, RC));
+
+ /* go go gadget! */
+ __raw_writel(ATMEL_TC_CLKEN | ATMEL_TC_SWTRG,
+ tcaddr + ATMEL_TC_REG(2, CCR));
+ return 0;
+}
+
+static struct tc_clkevt_device clkevt = {
+ .clkevt = {
+ .name = "tc_clkevt",
+ .features = CLOCK_EVT_FEAT_PERIODIC
+ | CLOCK_EVT_FEAT_ONESHOT,
+ .shift = 32,
+ /* Should be lower than at91rm9200's system timer */
+ .rating = 125,
+ .cpumask = CPU_MASK_CPU0,
+ .set_next_event = tc_next_event,
+ .set_mode = tc_mode,
+ },
+};
+
+static irqreturn_t ch2_irq(int irq, void *handle)
+{
+ struct tc_clkevt_device *dev = handle;
+ unsigned int sr;
+
+ sr = __raw_readl(dev->regs + ATMEL_TC_REG(2, SR));
+ if (sr & ATMEL_TC_CPCS) {
+ dev->clkevt.event_handler(&dev->clkevt);
+ return IRQ_HANDLED;
+ }
+
+ return IRQ_NONE;
+}
+
+static struct irqaction tc_irqaction = {
+ .name = "tc_clkevt",
+ .flags = IRQF_TIMER | IRQF_DISABLED,
+ .handler = ch2_irq,
+};
+
+static void __init setup_clkevents(struct atmel_tc *tc, int clk32k_divisor_idx)
+{
+ struct clk *t2_clk = tc->clk[2];
+ int irq = tc->irq[2];
+
+ clkevt.regs = tc->regs;
+ clkevt.clk = t2_clk;
+ tc_irqaction.dev_id = &clkevt;
+
+ timer_clock = clk32k_divisor_idx;
+
+ clkevt.clkevt.mult = div_sc(32768, NSEC_PER_SEC, clkevt.clkevt.shift);
+ clkevt.clkevt.max_delta_ns
+ = clockevent_delta2ns(0xffff, &clkevt.clkevt);
+ clkevt.clkevt.min_delta_ns = clockevent_delta2ns(1, &clkevt.clkevt) + 1;
+
+ setup_irq(irq, &tc_irqaction);
+
+ clockevents_register_device(&clkevt.clkevt);
+}
+
+#else /* !CONFIG_GENERIC_CLOCKEVENTS */
+
+static void __init setup_clkevents(struct atmel_tc *tc, int clk32k_divisor_idx)
+{
+ /* NOTHING */
+}
+
+#endif
+
+static int __init tcb_clksrc_init(void)
+{
+ static char bootinfo[] __initdata
+ = KERN_DEBUG "%s: tc%d at %d.%03d MHz\n";
+
+ struct platform_device *pdev;
+ struct atmel_tc *tc;
+ struct clk *t0_clk;
+ u32 rate, divided_rate = 0;
+ int best_divisor_idx = -1;
+ int clk32k_divisor_idx = -1;
+ int i;
+
+ tc = atmel_tc_alloc(CONFIG_ATMEL_TCB_CLKSRC_BLOCK, clksrc.name);
+ if (!tc) {
+ pr_debug("can't alloc TC for clocksource\n");
+ return -ENODEV;
+ }
+ tcaddr = tc->regs;
+ pdev = tc->pdev;
+
+ t0_clk = tc->clk[0];
+ clk_enable(t0_clk);
+
+ /* How fast will we be counting? Pick something over 5 MHz. */
+ rate = (u32) clk_get_rate(t0_clk);
+ for (i = 0; i < 5; i++) {
+ unsigned divisor = atmel_tc_divisors[i];
+ unsigned tmp;
+
+ /* remember 32 KiHz clock for later */
+ if (!divisor) {
+ clk32k_divisor_idx = i;
+ continue;
+ }
+
+ tmp = rate / divisor;
+ pr_debug("TC: %u / %-3u [%d] --> %u\n", rate, divisor, i, tmp);
+ if (best_divisor_idx > 0) {
+ if (tmp < 5 * 1000 * 1000)
+ continue;
+ }
+ divided_rate = tmp;
+ best_divisor_idx = i;
+ }
+
+ clksrc.mult = clocksource_hz2mult(divided_rate, clksrc.shift);
+
+ printk(bootinfo, clksrc.name, CONFIG_ATMEL_TCB_CLKSRC_BLOCK,
+ divided_rate / 1000000,
+ ((divided_rate + 500000) % 1000000) / 1000);
+
+ /* tclib will give us three clocks no matter what the
+ * underlying platform supports.
+ */
+ clk_enable(tc->clk[1]);
+
+ /* channel 0: waveform mode, input mclk/8, clock TIOA0 on overflow */
+ __raw_writel(best_divisor_idx /* likely divide-by-8 */
+ | ATMEL_TC_WAVE
+ | ATMEL_TC_WAVESEL_UP /* free-run */
+ | ATMEL_TC_ACPA_SET /* TIOA0 rises at 0 */
+ | ATMEL_TC_ACPC_CLEAR, /* (duty cycle 50%) */
+ tcaddr + ATMEL_TC_REG(0, CMR));
+ __raw_writel(0x0000, tcaddr + ATMEL_TC_REG(0, RA));
+ __raw_writel(0x8000, tcaddr + ATMEL_TC_REG(0, RC));
+ __raw_writel(0xff, tcaddr + ATMEL_TC_REG(0, IDR)); /* no irqs */
+ __raw_writel(ATMEL_TC_CLKEN, tcaddr + ATMEL_TC_REG(0, CCR));
+
+ /* channel 1: waveform mode, input TIOA0 */
+ __raw_writel(ATMEL_TC_XC1 /* input: TIOA0 */
+ | ATMEL_TC_WAVE
+ | ATMEL_TC_WAVESEL_UP, /* free-run */
+ tcaddr + ATMEL_TC_REG(1, CMR));
+ __raw_writel(0xff, tcaddr + ATMEL_TC_REG(1, IDR)); /* no irqs */
+ __raw_writel(ATMEL_TC_CLKEN, tcaddr + ATMEL_TC_REG(1, CCR));
+
+ /* chain channel 0 to channel 1, then reset all the timers */
+ __raw_writel(ATMEL_TC_TC1XC1S_TIOA0, tcaddr + ATMEL_TC_BMR);
+ __raw_writel(ATMEL_TC_SYNC, tcaddr + ATMEL_TC_BCR);
+
+ /* and away we go! */
+ clocksource_register(&clksrc);
+
+ /* channel 2: periodic and oneshot timer support */
+ setup_clkevents(tc, clk32k_divisor_idx);
+
+ return 0;
+}
+arch_initcall(tcb_clksrc_init);
purposes including software controlled power-efficent backlights
on LCD displays, motor control, and waveform generation.
+config ATMEL_TCLIB
+ bool "Atmel AT32/AT91 Timer/Counter Library"
+ depends on (AVR32 || ARCH_AT91)
+ help
+ Select this if you want a library to allocate the Timer/Counter
+ blocks found on many Atmel processors. This facilitates using
+ these blocks by different drivers despite processor differences.
+
+config ATMEL_TCB_CLKSRC
+ bool "TC Block Clocksource"
+ depends on ATMEL_TCLIB && GENERIC_TIME
+ default y
+ help
+ Select this to get a high precision clocksource based on a
+ TC block with a 5+ MHz base clock rate. Two timer channels
+ are combined to make a single 32-bit timer.
+
+ When GENERIC_CLOCKEVENTS is defined, the third timer channel
+ may be used as a clock event device supporting oneshot mode
+ (delays of up to two seconds) based on the 32 KiHz clock.
+
+config ATMEL_TCB_CLKSRC_BLOCK
+ int
+ depends on ATMEL_TCB_CLKSRC
+ prompt "TC Block" if ARCH_AT91RM9200 || ARCH_AT91SAM9260 || CPU_AT32AP700X
+ default 0
+ range 0 1
+ help
+ Some chips provide more than one TC block, so you have the
+ choice of which one to use for the clock framework. The other
+ TC can be used for other purposes, such as PWM generation and
+ interval timing.
+
config IBM_ASM
tristate "Device driver for IBM RSA service processor"
depends on X86 && PCI && INPUT && EXPERIMENTAL
obj-$(CONFIG_ASUS_LAPTOP) += asus-laptop.o
obj-$(CONFIG_ATMEL_PWM) += atmel_pwm.o
obj-$(CONFIG_ATMEL_SSC) += atmel-ssc.o
+obj-$(CONFIG_ATMEL_TCLIB) += atmel_tclib.o
obj-$(CONFIG_TC1100_WMI) += tc1100-wmi.o
obj-$(CONFIG_LKDTM) += lkdtm.o
obj-$(CONFIG_TIFM_CORE) += tifm_core.o
--- /dev/null
+#include <linux/atmel_tc.h>
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/ioport.h>
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+
+/* Number of bytes to reserve for the iomem resource */
+#define ATMEL_TC_IOMEM_SIZE 256
+
+
+/*
+ * This is a thin library to solve the problem of how to portably allocate
+ * one of the TC blocks. For simplicity, it doesn't currently expect to
+ * share individual timers between different drivers.
+ */
+
+#if defined(CONFIG_AVR32)
+/* AVR32 has these divide PBB */
+const u8 atmel_tc_divisors[5] = { 0, 4, 8, 16, 32, };
+EXPORT_SYMBOL(atmel_tc_divisors);
+
+#elif defined(CONFIG_ARCH_AT91)
+/* AT91 has these divide MCK */
+const u8 atmel_tc_divisors[5] = { 2, 8, 32, 128, 0, };
+EXPORT_SYMBOL(atmel_tc_divisors);
+
+#endif
+
+static DEFINE_SPINLOCK(tc_list_lock);
+static LIST_HEAD(tc_list);
+
+/**
+ * atmel_tc_alloc - allocate a specified TC block
+ * @block: which block to allocate
+ * @name: name to be associated with the iomem resource
+ *
+ * Caller allocates a block. If it is available, a pointer to a
+ * pre-initialized struct atmel_tc is returned. The caller can access
+ * the registers directly through the "regs" field.
+ */
+struct atmel_tc *atmel_tc_alloc(unsigned block, const char *name)
+{
+ struct atmel_tc *tc;
+ struct platform_device *pdev = NULL;
+ struct resource *r;
+
+ spin_lock(&tc_list_lock);
+ list_for_each_entry(tc, &tc_list, node) {
+ if (tc->pdev->id == block) {
+ pdev = tc->pdev;
+ break;
+ }
+ }
+
+ if (!pdev || tc->iomem)
+ goto fail;
+
+ r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ r = request_mem_region(r->start, ATMEL_TC_IOMEM_SIZE, name);
+ if (!r)
+ goto fail;
+
+ tc->regs = ioremap(r->start, ATMEL_TC_IOMEM_SIZE);
+ if (!tc->regs)
+ goto fail_ioremap;
+
+ tc->iomem = r;
+
+out:
+ spin_unlock(&tc_list_lock);
+ return tc;
+
+fail_ioremap:
+ release_resource(r);
+fail:
+ tc = NULL;
+ goto out;
+}
+EXPORT_SYMBOL_GPL(atmel_tc_alloc);
+
+/**
+ * atmel_tc_free - release a specified TC block
+ * @tc: Timer/counter block that was returned by atmel_tc_alloc()
+ *
+ * This reverses the effect of atmel_tc_alloc(), unmapping the I/O
+ * registers, invalidating the resource returned by that routine and
+ * making the TC available to other drivers.
+ */
+void atmel_tc_free(struct atmel_tc *tc)
+{
+ spin_lock(&tc_list_lock);
+ if (tc->regs) {
+ iounmap(tc->regs);
+ release_resource(tc->iomem);
+ tc->regs = NULL;
+ tc->iomem = NULL;
+ }
+ spin_unlock(&tc_list_lock);
+}
+EXPORT_SYMBOL_GPL(atmel_tc_free);
+
+static int __init tc_probe(struct platform_device *pdev)
+{
+ struct atmel_tc *tc;
+ struct clk *clk;
+ int irq;
+
+ if (!platform_get_resource(pdev, IORESOURCE_MEM, 0))
+ return -EINVAL;
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0)
+ return -EINVAL;
+
+ tc = kzalloc(sizeof(struct atmel_tc), GFP_KERNEL);
+ if (!tc)
+ return -ENOMEM;
+
+ tc->pdev = pdev;
+
+ clk = clk_get(&pdev->dev, "t0_clk");
+ if (IS_ERR(clk)) {
+ kfree(tc);
+ return -EINVAL;
+ }
+
+ tc->clk[0] = clk;
+ tc->clk[1] = clk_get(&pdev->dev, "t1_clk");
+ if (IS_ERR(tc->clk[1]))
+ tc->clk[1] = clk;
+ tc->clk[2] = clk_get(&pdev->dev, "t2_clk");
+ if (IS_ERR(tc->clk[2]))
+ tc->clk[2] = clk;
+
+ tc->irq[0] = irq;
+ tc->irq[1] = platform_get_irq(pdev, 1);
+ if (tc->irq[1] < 0)
+ tc->irq[1] = irq;
+ tc->irq[2] = platform_get_irq(pdev, 2);
+ if (tc->irq[2] < 0)
+ tc->irq[2] = irq;
+
+ spin_lock(&tc_list_lock);
+ list_add_tail(&tc->node, &tc_list);
+ spin_unlock(&tc_list_lock);
+
+ return 0;
+}
+
+static struct platform_driver tc_driver = {
+ .driver.name = "atmel_tcb",
+};
+
+static int __init tc_init(void)
+{
+ return platform_driver_probe(&tc_driver, tc_probe);
+}
+arch_initcall(tc_init);
config PARPORT_PC
tristate "PC-style hardware"
depends on (!SPARC64 || PCI) && !SPARC32 && !M32R && !FRV && \
- (!M68K || ISA) && !MN10300
+ (!M68K || ISA) && !MN10300 && !AVR32
---help---
You should say Y here if you have a PC-style parallel port. All
IBM PC compatible computers and some Alphas have PC-style
config USB_GADGET_ATMEL_USBA
boolean "Atmel USBA"
select USB_GADGET_DUALSPEED
- depends on AVR32
+ depends on AVR32 || ARCH_AT91CAP9
help
USBA is the integrated high-speed USB Device controller on
- the AT32AP700x processors from Atmel.
+ the AT32AP700x and AT91CAP9 processors from Atmel.
config USB_ATMEL_USBA
tristate
#include <linux/platform_device.h>
#include <linux/usb/ch9.h>
#include <linux/usb/gadget.h>
+#include <linux/usb/atmel_usba_udc.h>
#include <linux/delay.h>
#include <asm/gpio.h>
static struct usba_udc the_udc;
+static struct usba_ep *usba_ep;
#ifdef CONFIG_USB_GADGET_DEBUG_FS
#include <linux/debugfs.h>
return 1;
}
-static void copy_to_fifo(void __iomem *fifo, const void *buf, int len)
+#if defined(CONFIG_AVR32)
+
+static void toggle_bias(int is_on)
{
- unsigned long tmp;
-
- DBG(DBG_FIFO, "copy to FIFO (len %d):\n", len);
- for (; len > 0; len -= 4, buf += 4, fifo += 4) {
- tmp = *(unsigned long *)buf;
- if (len >= 4) {
- DBG(DBG_FIFO, " -> %08lx\n", tmp);
- __raw_writel(tmp, fifo);
- } else {
- do {
- DBG(DBG_FIFO, " -> %02lx\n", tmp >> 24);
- __raw_writeb(tmp >> 24, fifo);
- fifo++;
- tmp <<= 8;
- } while (--len);
- break;
- }
- }
}
-static void copy_from_fifo(void *buf, void __iomem *fifo, int len)
+#elif defined(CONFIG_ARCH_AT91)
+
+#include <asm/arch/at91_pmc.h>
+
+static void toggle_bias(int is_on)
{
- union {
- unsigned long *w;
- unsigned char *b;
- } p;
- unsigned long tmp;
-
- DBG(DBG_FIFO, "copy from FIFO (len %d):\n", len);
- for (p.w = buf; len > 0; len -= 4, p.w++, fifo += 4) {
- if (len >= 4) {
- tmp = __raw_readl(fifo);
- *p.w = tmp;
- DBG(DBG_FIFO, " -> %08lx\n", tmp);
- } else {
- do {
- tmp = __raw_readb(fifo);
- *p.b = tmp;
- DBG(DBG_FIFO, " -> %02lx\n", tmp);
- fifo++, p.b++;
- } while (--len);
- }
- }
+ unsigned int uckr = at91_sys_read(AT91_CKGR_UCKR);
+
+ if (is_on)
+ at91_sys_write(AT91_CKGR_UCKR, uckr | AT91_PMC_BIASEN);
+ else
+ at91_sys_write(AT91_CKGR_UCKR, uckr & ~(AT91_PMC_BIASEN));
}
+#endif /* CONFIG_ARCH_AT91 */
+
static void next_fifo_transaction(struct usba_ep *ep, struct usba_request *req)
{
unsigned int transaction_len;
ep->ep.name, req, transaction_len,
req->last_transaction ? ", done" : "");
- copy_to_fifo(ep->fifo, req->req.buf + req->req.actual, transaction_len);
+ memcpy_toio(ep->fifo, req->req.buf + req->req.actual, transaction_len);
usba_ep_writel(ep, SET_STA, USBA_TX_PK_RDY);
req->req.actual += transaction_len;
}
bytecount = req->req.length - req->req.actual;
}
- copy_from_fifo(req->req.buf + req->req.actual,
+ memcpy_fromio(req->req.buf + req->req.actual,
ep->fifo, bytecount);
req->req.actual += bytecount;
.set_selfpowered = usba_udc_set_selfpowered,
};
-#define EP(nam, idx, maxpkt, maxbk, dma, isoc) \
-{ \
- .ep = { \
- .ops = &usba_ep_ops, \
- .name = nam, \
- .maxpacket = maxpkt, \
- }, \
- .udc = &the_udc, \
- .queue = LIST_HEAD_INIT(usba_ep[idx].queue), \
- .fifo_size = maxpkt, \
- .nr_banks = maxbk, \
- .index = idx, \
- .can_dma = dma, \
- .can_isoc = isoc, \
-}
-
-static struct usba_ep usba_ep[] = {
- EP("ep0", 0, 64, 1, 0, 0),
- EP("ep1in-bulk", 1, 512, 2, 1, 1),
- EP("ep2out-bulk", 2, 512, 2, 1, 1),
- EP("ep3in-int", 3, 64, 3, 1, 0),
- EP("ep4out-int", 4, 64, 3, 1, 0),
- EP("ep5in-iso", 5, 1024, 3, 1, 1),
- EP("ep6out-iso", 6, 1024, 3, 1, 1),
-};
-#undef EP
-
static struct usb_endpoint_descriptor usba_ep0_desc = {
.bLength = USB_DT_ENDPOINT_SIZE,
.bDescriptorType = USB_DT_ENDPOINT,
static struct usba_udc the_udc = {
.gadget = {
.ops = &usba_udc_ops,
- .ep0 = &usba_ep[0].ep,
.ep_list = LIST_HEAD_INIT(the_udc.gadget.ep_list),
.is_dualspeed = 1,
.name = "atmel_usba_udc",
} else {
usba_ep_writel(ep, CTL_ENB, USBA_EPT_ENABLE);
usba_writel(udc, TST, USBA_TST_PKT_MODE);
- copy_to_fifo(ep->fifo, test_packet_buffer,
+ memcpy_toio(ep->fifo, test_packet_buffer,
sizeof(test_packet_buffer));
usba_ep_writel(ep, SET_STA, USBA_TX_PK_RDY);
dev_info(dev, "Entering Test_Packet mode...\n");
DBG(DBG_HW, "Packet length: %u\n", pkt_len);
if (pkt_len != sizeof(crq)) {
pr_warning("udc: Invalid packet length %u "
- "(expected %lu)\n", pkt_len, sizeof(crq));
+ "(expected %zu)\n", pkt_len, sizeof(crq));
set_protocol_stall(udc, ep);
return;
}
DBG(DBG_FIFO, "Copying ctrl request from 0x%p:\n", ep->fifo);
- copy_from_fifo(crq.data, ep->fifo, sizeof(crq));
+ memcpy_fromio(crq.data, ep->fifo, sizeof(crq));
/* Free up one bank in the FIFO so that we can
* generate or receive a reply right away. */
DBG(DBG_INT, "irq, status=%#08x\n", status);
if (status & USBA_DET_SUSPEND) {
+ toggle_bias(0);
usba_writel(udc, INT_CLR, USBA_DET_SUSPEND);
DBG(DBG_BUS, "Suspend detected\n");
if (udc->gadget.speed != USB_SPEED_UNKNOWN
}
if (status & USBA_WAKE_UP) {
+ toggle_bias(1);
usba_writel(udc, INT_CLR, USBA_WAKE_UP);
DBG(DBG_BUS, "Wake Up CPU detected\n");
}
vbus = gpio_get_value(udc->vbus_pin);
if (vbus != udc->vbus_prev) {
if (vbus) {
- usba_writel(udc, CTRL, USBA_EN_USBA);
+ toggle_bias(1);
+ usba_writel(udc, CTRL, USBA_ENABLE_MASK);
usba_writel(udc, INT_ENB, USBA_END_OF_RESET);
} else {
udc->gadget.speed = USB_SPEED_UNKNOWN;
reset_all_endpoints(udc);
- usba_writel(udc, CTRL, 0);
+ toggle_bias(0);
+ usba_writel(udc, CTRL, USBA_DISABLE_MASK);
spin_unlock(&udc->lock);
udc->driver->disconnect(&udc->gadget);
spin_lock(&udc->lock);
/* If Vbus is present, enable the controller and wait for reset */
spin_lock_irqsave(&udc->lock, flags);
if (vbus_is_present(udc) && udc->vbus_prev == 0) {
- usba_writel(udc, CTRL, USBA_EN_USBA);
+ toggle_bias(1);
+ usba_writel(udc, CTRL, USBA_ENABLE_MASK);
usba_writel(udc, INT_ENB, USBA_END_OF_RESET);
}
spin_unlock_irqrestore(&udc->lock, flags);
spin_unlock_irqrestore(&udc->lock, flags);
/* This will also disable the DP pullup */
- usba_writel(udc, CTRL, 0);
+ toggle_bias(0);
+ usba_writel(udc, CTRL, USBA_DISABLE_MASK);
driver->unbind(&udc->gadget);
udc->gadget.dev.driver = NULL;
regs = platform_get_resource(pdev, IORESOURCE_MEM, CTRL_IOMEM_ID);
fifo = platform_get_resource(pdev, IORESOURCE_MEM, FIFO_IOMEM_ID);
- if (!regs || !fifo)
+ if (!regs || !fifo || !pdata)
return -ENXIO;
irq = platform_get_irq(pdev, 0);
/* Make sure we start from a clean slate */
clk_enable(pclk);
- usba_writel(udc, CTRL, 0);
+ toggle_bias(0);
+ usba_writel(udc, CTRL, USBA_DISABLE_MASK);
clk_disable(pclk);
+ usba_ep = kmalloc(sizeof(struct usba_ep) * pdata->num_ep,
+ GFP_KERNEL);
+ if (!usba_ep)
+ goto err_alloc_ep;
+
+ the_udc.gadget.ep0 = &usba_ep[0].ep;
+
INIT_LIST_HEAD(&usba_ep[0].ep.ep_list);
usba_ep[0].ep_regs = udc->regs + USBA_EPT_BASE(0);
usba_ep[0].dma_regs = udc->regs + USBA_DMA_BASE(0);
usba_ep[0].fifo = udc->fifo + USBA_FIFO_BASE(0);
- for (i = 1; i < ARRAY_SIZE(usba_ep); i++) {
+ usba_ep[0].ep.ops = &usba_ep_ops;
+ usba_ep[0].ep.name = pdata->ep[0].name;
+ usba_ep[0].ep.maxpacket = pdata->ep[0].fifo_size;
+ usba_ep[0].udc = &the_udc;
+ INIT_LIST_HEAD(&usba_ep[0].queue);
+ usba_ep[0].fifo_size = pdata->ep[0].fifo_size;
+ usba_ep[0].nr_banks = pdata->ep[0].nr_banks;
+ usba_ep[0].index = pdata->ep[0].index;
+ usba_ep[0].can_dma = pdata->ep[0].can_dma;
+ usba_ep[0].can_isoc = pdata->ep[0].can_isoc;
+
+ for (i = 1; i < pdata->num_ep; i++) {
struct usba_ep *ep = &usba_ep[i];
ep->ep_regs = udc->regs + USBA_EPT_BASE(i);
ep->dma_regs = udc->regs + USBA_DMA_BASE(i);
ep->fifo = udc->fifo + USBA_FIFO_BASE(i);
+ ep->ep.ops = &usba_ep_ops;
+ ep->ep.name = pdata->ep[i].name;
+ ep->ep.maxpacket = pdata->ep[i].fifo_size;
+ ep->udc = &the_udc;
+ INIT_LIST_HEAD(&ep->queue);
+ ep->fifo_size = pdata->ep[i].fifo_size;
+ ep->nr_banks = pdata->ep[i].nr_banks;
+ ep->index = pdata->ep[i].index;
+ ep->can_dma = pdata->ep[i].can_dma;
+ ep->can_isoc = pdata->ep[i].can_isoc;
list_add_tail(&ep->ep.ep_list, &udc->gadget.ep_list);
}
goto err_device_add;
}
- if (pdata && pdata->vbus_pin != GPIO_PIN_NONE) {
+ if (pdata->vbus_pin >= 0) {
if (!gpio_request(pdata->vbus_pin, "atmel_usba_udc")) {
udc->vbus_pin = pdata->vbus_pin;
}
usba_init_debugfs(udc);
- for (i = 1; i < ARRAY_SIZE(usba_ep); i++)
+ for (i = 1; i < pdata->num_ep; i++)
usba_ep_init_debugfs(udc, &usba_ep[i]);
return 0;
err_device_add:
free_irq(irq, udc);
err_request_irq:
+ kfree(usba_ep);
+err_alloc_ep:
iounmap(udc->fifo);
err_map_fifo:
iounmap(udc->regs);
{
struct usba_udc *udc;
int i;
+ struct usba_platform_data *pdata = pdev->dev.platform_data;
udc = platform_get_drvdata(pdev);
- for (i = 1; i < ARRAY_SIZE(usba_ep); i++)
+ for (i = 1; i < pdata->num_ep; i++)
usba_ep_cleanup_debugfs(&usba_ep[i]);
usba_cleanup_debugfs(udc);
gpio_free(udc->vbus_pin);
free_irq(udc->irq, udc);
+ kfree(usba_ep);
iounmap(udc->fifo);
iounmap(udc->regs);
clk_put(udc->hclk);
#define USBA_EN_USBA (1 << 8)
#define USBA_DETACH (1 << 9)
#define USBA_REMOTE_WAKE_UP (1 << 10)
+#define USBA_PULLD_DIS (1 << 11)
+
+#if defined(CONFIG_AVR32)
+#define USBA_ENABLE_MASK USBA_EN_USBA
+#define USBA_DISABLE_MASK 0
+#elif defined(CONFIG_ARCH_AT91)
+#define USBA_ENABLE_MASK (USBA_EN_USBA | USBA_PULLD_DIS)
+#define USBA_DISABLE_MASK USBA_DETACH
+#endif /* CONFIG_ARCH_AT91 */
/* Bitfields in FNUM */
#define USBA_MICRO_FRAME_NUM_OFFSET 0
at32_add_device_lcdc(unsigned int id, struct atmel_lcdfb_info *data,
unsigned long fbmem_start, unsigned long fbmem_len);
-struct usba_platform_data {
- int vbus_pin;
-};
+struct usba_platform_data;
struct platform_device *
at32_add_device_usba(unsigned int id, struct usba_platform_data *data);
struct platform_device *
at32_add_device_ssc(unsigned int id, unsigned int flags);
-struct platform_device *at32_add_device_twi(unsigned int id);
+struct i2c_board_info;
+struct platform_device *at32_add_device_twi(unsigned int id,
+ struct i2c_board_info *b,
+ unsigned int n);
struct platform_device *at32_add_device_mci(unsigned int id);
struct platform_device *at32_add_device_ac97c(unsigned int id);
struct platform_device *at32_add_device_abdac(unsigned int id);
--- /dev/null
+/*
+ * AVR32 AP Power Management.
+ *
+ * Copyright (C) 2008 Atmel Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#ifndef __ASM_AVR32_ARCH_PM_H
+#define __ASM_AVR32_ARCH_PM_H
+
+/* Possible arguments to the "sleep" instruction */
+#define CPU_SLEEP_IDLE 0
+#define CPU_SLEEP_FROZEN 1
+#define CPU_SLEEP_STANDBY 2
+#define CPU_SLEEP_STOP 3
+#define CPU_SLEEP_STATIC 5
+
+#ifndef __ASSEMBLY__
+extern void cpu_enter_idle(void);
+
+extern bool disable_idle_sleep;
+
+static inline void cpu_disable_idle_sleep(void)
+{
+ disable_idle_sleep = true;
+}
+
+static inline void cpu_enable_idle_sleep(void)
+{
+ disable_idle_sleep = false;
+}
+
+static inline void cpu_idle_sleep(void)
+{
+ /*
+ * If we're using the COUNT and COMPARE registers for
+ * timekeeping, we can't use the IDLE state.
+ */
+ if (disable_idle_sleep)
+ cpu_relax();
+ else
+ cpu_enter_idle();
+}
+#endif
+
+#endif /* __ASM_AVR32_ARCH_PM_H */
+++ /dev/null
-/*
- * Copyright (C) 2007 Atmel Corporation
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef _ASM_AVR32_ARCH_AT32AP_TIME_H
-#define _ASM_AVR32_ARCH_AT32AP_TIME_H
-
-#include <linux/platform_device.h>
-
-extern struct irqaction timer_irqaction;
-extern struct platform_device at32_systc0_device;
-extern void local_timer_interrupt(int irq, void *dev_id);
-
-#define TIMER_BCR 0x000000c0
-#define TIMER_BCR_SYNC 0
-#define TIMER_BMR 0x000000c4
-#define TIMER_BMR_TC0XC0S 0
-#define TIMER_BMR_TC1XC1S 2
-#define TIMER_BMR_TC2XC2S 4
-#define TIMER_CCR 0x00000000
-#define TIMER_CCR_CLKDIS 1
-#define TIMER_CCR_CLKEN 0
-#define TIMER_CCR_SWTRG 2
-#define TIMER_CMR 0x00000004
-#define TIMER_CMR_ABETRG 10
-#define TIMER_CMR_ACPA 16
-#define TIMER_CMR_ACPC 18
-#define TIMER_CMR_AEEVT 20
-#define TIMER_CMR_ASWTRG 22
-#define TIMER_CMR_BCPB 24
-#define TIMER_CMR_BCPC 26
-#define TIMER_CMR_BEEVT 28
-#define TIMER_CMR_BSWTRG 30
-#define TIMER_CMR_BURST 4
-#define TIMER_CMR_CLKI 3
-#define TIMER_CMR_CPCDIS 7
-#define TIMER_CMR_CPCSTOP 6
-#define TIMER_CMR_CPCTRG 14
-#define TIMER_CMR_EEVT 10
-#define TIMER_CMR_EEVTEDG 8
-#define TIMER_CMR_ENETRG 12
-#define TIMER_CMR_ETRGEDG 8
-#define TIMER_CMR_LDBDIS 7
-#define TIMER_CMR_LDBSTOP 6
-#define TIMER_CMR_LDRA 16
-#define TIMER_CMR_LDRB 18
-#define TIMER_CMR_TCCLKS 0
-#define TIMER_CMR_WAVE 15
-#define TIMER_CMR_WAVSEL 13
-#define TIMER_CV 0x00000010
-#define TIMER_CV_CV 0
-#define TIMER_IDR 0x00000028
-#define TIMER_IDR_COVFS 0
-#define TIMER_IDR_CPAS 2
-#define TIMER_IDR_CPBS 3
-#define TIMER_IDR_CPCS 4
-#define TIMER_IDR_ETRGS 7
-#define TIMER_IDR_LDRAS 5
-#define TIMER_IDR_LDRBS 6
-#define TIMER_IDR_LOVRS 1
-#define TIMER_IER 0x00000024
-#define TIMER_IER_COVFS 0
-#define TIMER_IER_CPAS 2
-#define TIMER_IER_CPBS 3
-#define TIMER_IER_CPCS 4
-#define TIMER_IER_ETRGS 7
-#define TIMER_IER_LDRAS 5
-#define TIMER_IER_LDRBS 6
-#define TIMER_IER_LOVRS 1
-#define TIMER_IMR 0x0000002c
-#define TIMER_IMR_COVFS 0
-#define TIMER_IMR_CPAS 2
-#define TIMER_IMR_CPBS 3
-#define TIMER_IMR_CPCS 4
-#define TIMER_IMR_ETRGS 7
-#define TIMER_IMR_LDRAS 5
-#define TIMER_IMR_LDRBS 6
-#define TIMER_IMR_LOVRS 1
-#define TIMER_RA 0x00000014
-#define TIMER_RA_RA 0
-#define TIMER_RB 0x00000018
-#define TIMER_RB_RB 0
-#define TIMER_RC 0x0000001c
-#define TIMER_RC_RC 0
-#define TIMER_SR 0x00000020
-#define TIMER_SR_CLKSTA 16
-#define TIMER_SR_COVFS 0
-#define TIMER_SR_CPAS 2
-#define TIMER_SR_CPBS 3
-#define TIMER_SR_CPCS 4
-#define TIMER_SR_ETRGS 7
-#define TIMER_SR_LDRAS 5
-#define TIMER_SR_LDRBS 6
-#define TIMER_SR_LOVRS 1
-#define TIMER_SR_MTIOA 17
-#define TIMER_SR_MTIOB 18
-
-/* Bit manipulation macros */
-#define TIMER_BIT(name) (1 << TIMER_##name)
-#define TIMER_BF(name,value) ((value) << TIMER_##name)
-
-/* Register access macros */
-#define timer_read(port,instance,reg) \
- __raw_readl(port + (0x40 * instance) + TIMER_##reg)
-#define timer_write(port,instance,reg,value) \
- __raw_writel((value), port + (0x40 * instance) + TIMER_##reg)
-
-#endif /* _ASM_AVR32_ARCH_AT32AP_TIME_H */
#include <asm/asm-offsets.h>
#include <asm/thread_info.h>
-#define mask_interrupts ssrf SR_GM_BIT
-#define mask_exceptions ssrf SR_EM_BIT
-#define unmask_interrupts csrf SR_GM_BIT
-#define unmask_exceptions csrf SR_EM_BIT
+#define mask_interrupts ssrf SYSREG_GM_OFFSET
+#define mask_exceptions ssrf SYSREG_EM_OFFSET
+#define unmask_interrupts csrf SYSREG_GM_OFFSET
+#define unmask_exceptions csrf SYSREG_EM_OFFSET
#ifdef CONFIG_FRAME_POINTER
.macro save_fp
+++ /dev/null
-#ifndef __ASM_AVR32_INTC_H
-#define __ASM_AVR32_INTC_H
-
-#include <linux/sysdev.h>
-#include <linux/interrupt.h>
-
-struct irq_controller;
-struct irqaction;
-struct pt_regs;
-
-struct platform_device;
-
-/* Information about the internal interrupt controller */
-struct intc_device {
- /* ioremapped address of configuration block */
- void __iomem *regs;
-
- /* the physical device */
- struct platform_device *pdev;
-
- /* Number of interrupt lines per group. */
- unsigned int irqs_per_group;
-
- /* The highest group ID + 1 */
- unsigned int nr_groups;
-
- /*
- * Bitfield indicating which groups are actually in use. The
- * size of the array is
- * ceil(group_max / (8 * sizeof(unsigned int))).
- */
- unsigned int group_mask[];
-};
-
-struct irq_controller_class {
- /*
- * A short name identifying this kind of controller.
- */
- const char *typename;
- /*
- * Handle the IRQ. Must do any necessary acking and masking.
- */
- irqreturn_t (*handle)(int irq, void *dev_id, struct pt_regs *regs);
- /*
- * Register a new IRQ handler.
- */
- int (*setup)(struct irq_controller *ctrl, unsigned int irq,
- struct irqaction *action);
- /*
- * Unregister a IRQ handler.
- */
- void (*free)(struct irq_controller *ctrl, unsigned int irq,
- void *dev_id);
- /*
- * Mask the IRQ in the interrupt controller.
- */
- void (*mask)(struct irq_controller *ctrl, unsigned int irq);
- /*
- * Unmask the IRQ in the interrupt controller.
- */
- void (*unmask)(struct irq_controller *ctrl, unsigned int irq);
- /*
- * Set the type of the IRQ. See below for possible types.
- * Return -EINVAL if a given type is not supported
- */
- int (*set_type)(struct irq_controller *ctrl, unsigned int irq,
- unsigned int type);
- /*
- * Return the IRQ type currently set
- */
- unsigned int (*get_type)(struct irq_controller *ctrl, unsigned int irq);
-};
-
-struct irq_controller {
- struct irq_controller_class *class;
- unsigned int irq_group;
- unsigned int first_irq;
- unsigned int nr_irqs;
- struct list_head list;
-};
-
-struct intc_group_desc {
- struct irq_controller *ctrl;
- irqreturn_t (*handle)(int, void *, struct pt_regs *);
- unsigned long flags;
- void *dev_id;
- const char *devname;
-};
-
-/*
- * The internal interrupt controller. Defined in board/part-specific
- * devices.c.
- * TODO: Should probably be defined per-cpu.
- */
-extern struct intc_device intc;
-
-extern int request_internal_irq(unsigned int irq,
- irqreturn_t (*handler)(int, void *, struct pt_regs *),
- unsigned long irqflags,
- const char *devname, void *dev_id);
-extern void free_internal_irq(unsigned int irq);
-
-/* Only used by time_init() */
-extern int setup_internal_irq(unsigned int irq, struct intc_group_desc *desc);
-
-/*
- * Set interrupt priority for a given group. `group' can be found by
- * using irq_to_group(irq). Priority can be from 0 (lowest) to 3
- * (highest). Higher-priority interrupts will preempt lower-priority
- * interrupts (unless interrupts are masked globally).
- *
- * This function does not check for conflicts within a group.
- */
-extern int intc_set_priority(unsigned int group,
- unsigned int priority);
-
-/*
- * Returns a bitmask of pending interrupts in a group.
- */
-extern unsigned long intc_get_pending(unsigned int group);
-
-/*
- * Register a new external interrupt controller. Returns the first
- * external IRQ number that is assigned to the new controller.
- */
-extern int intc_register_controller(struct irq_controller *ctrl);
-
-#endif /* __ASM_AVR32_INTC_H */
#ifndef __ASSEMBLER__
int nmi_enable(void);
void nmi_disable(void);
+
+/*
+ * Returns a bitmask of pending interrupts in a group.
+ */
+extern unsigned long intc_get_pending(unsigned int group);
#endif
#endif /* __ASM_AVR32_IOCTLS_H */
#ifndef __ASM_AVR32_PAGE_H
#define __ASM_AVR32_PAGE_H
+#include <linux/const.h>
+
/* PAGE_SHIFT determines the page size */
#define PAGE_SHIFT 12
-#ifdef __ASSEMBLY__
-#define PAGE_SIZE (1 << PAGE_SHIFT)
-#else
-#define PAGE_SIZE (1UL << PAGE_SHIFT)
-#endif
+#define PAGE_SIZE (_AC(1, UL) << PAGE_SHIFT)
#define PAGE_MASK (~(PAGE_SIZE-1))
#define PTE_MASK PAGE_MASK
--- /dev/null
+#ifndef _ASM_SERIAL_H
+#define _ASM_SERIAL_H
+
+/*
+ * This assumes you have a 1.8432 MHz clock for your UART.
+ *
+ * It'd be nice if someone built a serial card with a 24.576 MHz
+ * clock, since the 16550A is capable of handling a top speed of 1.5
+ * megabits/second; but this requires the faster clock.
+ */
+#define BASE_BAUD (1843200 / 16)
+
+#endif /* _ASM_SERIAL_H */
--- /dev/null
+#ifndef _ASM_XOR_H
+#define _ASM_XOR_H
+
+#include <asm-generic/xor.h>
+
+#endif
--- /dev/null
+/*
+ * Timer/Counter Unit (TC) registers.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef ATMEL_TC_H
+#define ATMEL_TC_H
+
+#include <linux/compiler.h>
+#include <linux/list.h>
+
+/*
+ * Many 32-bit Atmel SOCs include one or more TC blocks, each of which holds
+ * three general-purpose 16-bit timers. These timers share one register bank.
+ * Depending on the SOC, each timer may have its own clock and IRQ, or those
+ * may be shared by the whole TC block.
+ *
+ * These TC blocks may have up to nine external pins: TCLK0..2 signals for
+ * clocks or clock gates, and per-timer TIOA and TIOB signals used for PWM
+ * or triggering. Those pins need to be set up for use with the TC block,
+ * else they will be used as GPIOs or for a different controller.
+ *
+ * Although we expect each TC block to have a platform_device node, those
+ * nodes are not what drivers bind to. Instead, they ask for a specific
+ * TC block, by number ... which is a common approach on systems with many
+ * timers. Then they use clk_get() and platform_get_irq() to get clock and
+ * IRQ resources.
+ */
+
+struct clk;
+
+/**
+ * struct atmel_tc - information about a Timer/Counter Block
+ * @pdev: physical device
+ * @iomem: resource associated with the I/O register
+ * @regs: mapping through which the I/O registers can be accessed
+ * @irq: irq for each of the three channels
+ * @clk: internal clock source for each of the three channels
+ * @node: list node, for tclib internal use
+ *
+ * On some platforms, each TC channel has its own clocks and IRQs,
+ * while on others, all TC channels share the same clock and IRQ.
+ * Drivers should clk_enable() all the clocks they need even though
+ * all the entries in @clk may point to the same physical clock.
+ * Likewise, drivers should request irqs independently for each
+ * channel, but they must use IRQF_SHARED in case some of the entries
+ * in @irq are actually the same IRQ.
+ */
+struct atmel_tc {
+ struct platform_device *pdev;
+ struct resource *iomem;
+ void __iomem *regs;
+ int irq[3];
+ struct clk *clk[3];
+ struct list_head node;
+};
+
+extern struct atmel_tc *atmel_tc_alloc(unsigned block, const char *name);
+extern void atmel_tc_free(struct atmel_tc *tc);
+
+/* platform-specific ATMEL_TC_TIMER_CLOCKx divisors (0 means 32KiHz) */
+extern const u8 atmel_tc_divisors[5];
+
+
+/*
+ * Two registers have block-wide controls. These are: configuring the three
+ * "external" clocks (or event sources) used by the timer channels; and
+ * synchronizing the timers by resetting them all at once.
+ *
+ * "External" can mean "external to chip" using the TCLK0, TCLK1, or TCLK2
+ * signals. Or, it can mean "external to timer", using the TIOA output from
+ * one of the other two timers that's being run in waveform mode.
+ */
+
+#define ATMEL_TC_BCR 0xc0 /* TC Block Control Register */
+#define ATMEL_TC_SYNC (1 << 0) /* synchronize timers */
+
+#define ATMEL_TC_BMR 0xc4 /* TC Block Mode Register */
+#define ATMEL_TC_TC0XC0S (3 << 0) /* external clock 0 source */
+#define ATMEL_TC_TC0XC0S_TCLK0 (0 << 0)
+#define ATMEL_TC_TC0XC0S_NONE (1 << 0)
+#define ATMEL_TC_TC0XC0S_TIOA1 (2 << 0)
+#define ATMEL_TC_TC0XC0S_TIOA2 (3 << 0)
+#define ATMEL_TC_TC1XC1S (3 << 2) /* external clock 1 source */
+#define ATMEL_TC_TC1XC1S_TCLK1 (0 << 2)
+#define ATMEL_TC_TC1XC1S_NONE (1 << 2)
+#define ATMEL_TC_TC1XC1S_TIOA0 (2 << 2)
+#define ATMEL_TC_TC1XC1S_TIOA2 (3 << 2)
+#define ATMEL_TC_TC2XC2S (3 << 4) /* external clock 2 source */
+#define ATMEL_TC_TC2XC2S_TCLK2 (0 << 4)
+#define ATMEL_TC_TC2XC2S_NONE (1 << 4)
+#define ATMEL_TC_TC2XC2S_TIOA0 (2 << 4)
+#define ATMEL_TC_TC2XC2S_TIOA1 (3 << 4)
+
+
+/*
+ * Each TC block has three "channels", each with one counter and controls.
+ *
+ * Note that the semantics of ATMEL_TC_TIMER_CLOCKx (input clock selection
+ * when it's not "external") is silicon-specific. AT91 platforms use one
+ * set of definitions; AVR32 platforms use a different set. Don't hard-wire
+ * such knowledge into your code, use the global "atmel_tc_divisors" ...
+ * where index N is the divisor for clock N+1, else zero to indicate it uses
+ * the 32 KiHz clock.
+ *
+ * The timers can be chained in various ways, and operated in "waveform"
+ * generation mode (including PWM) or "capture" mode (to time events). In
+ * both modes, behavior can be configured in many ways.
+ *
+ * Each timer has two I/O pins, TIOA and TIOB. Waveform mode uses TIOA as a
+ * PWM output, and TIOB as either another PWM or as a trigger. Capture mode
+ * uses them only as inputs.
+ */
+#define ATMEL_TC_CHAN(idx) ((idx)*0x40)
+#define ATMEL_TC_REG(idx, reg) (ATMEL_TC_CHAN(idx) + ATMEL_TC_ ## reg)
+
+#define ATMEL_TC_CCR 0x00 /* Channel Control Register */
+#define ATMEL_TC_CLKEN (1 << 0) /* clock enable */
+#define ATMEL_TC_CLKDIS (1 << 1) /* clock disable */
+#define ATMEL_TC_SWTRG (1 << 2) /* software trigger */
+
+#define ATMEL_TC_CMR 0x04 /* Channel Mode Register */
+
+/* Both modes share some CMR bits */
+#define ATMEL_TC_TCCLKS (7 << 0) /* clock source */
+#define ATMEL_TC_TIMER_CLOCK1 (0 << 0)
+#define ATMEL_TC_TIMER_CLOCK2 (1 << 0)
+#define ATMEL_TC_TIMER_CLOCK3 (2 << 0)
+#define ATMEL_TC_TIMER_CLOCK4 (3 << 0)
+#define ATMEL_TC_TIMER_CLOCK5 (4 << 0)
+#define ATMEL_TC_XC0 (5 << 0)
+#define ATMEL_TC_XC1 (6 << 0)
+#define ATMEL_TC_XC2 (7 << 0)
+#define ATMEL_TC_CLKI (1 << 3) /* clock invert */
+#define ATMEL_TC_BURST (3 << 4) /* clock gating */
+#define ATMEL_TC_GATE_NONE (0 << 4)
+#define ATMEL_TC_GATE_XC0 (1 << 4)
+#define ATMEL_TC_GATE_XC1 (2 << 4)
+#define ATMEL_TC_GATE_XC2 (3 << 4)
+#define ATMEL_TC_WAVE (1 << 15) /* true = Waveform mode */
+
+/* CAPTURE mode CMR bits */
+#define ATMEL_TC_LDBSTOP (1 << 6) /* counter stops on RB load */
+#define ATMEL_TC_LDBDIS (1 << 7) /* counter disable on RB load */
+#define ATMEL_TC_ETRGEDG (3 << 8) /* external trigger edge */
+#define ATMEL_TC_ETRGEDG_NONE (0 << 8)
+#define ATMEL_TC_ETRGEDG_RISING (1 << 8)
+#define ATMEL_TC_ETRGEDG_FALLING (2 << 8)
+#define ATMEL_TC_ETRGEDG_BOTH (3 << 8)
+#define ATMEL_TC_ABETRG (1 << 10) /* external trigger is TIOA? */
+#define ATMEL_TC_CPCTRG (1 << 14) /* RC compare trigger enable */
+#define ATMEL_TC_LDRA (3 << 16) /* RA loading edge (of TIOA) */
+#define ATMEL_TC_LDRA_NONE (0 << 16)
+#define ATMEL_TC_LDRA_RISING (1 << 16)
+#define ATMEL_TC_LDRA_FALLING (2 << 16)
+#define ATMEL_TC_LDRA_BOTH (3 << 16)
+#define ATMEL_TC_LDRB (3 << 18) /* RB loading edge (of TIOA) */
+#define ATMEL_TC_LDRB_NONE (0 << 18)
+#define ATMEL_TC_LDRB_RISING (1 << 18)
+#define ATMEL_TC_LDRB_FALLING (2 << 18)
+#define ATMEL_TC_LDRB_BOTH (3 << 18)
+
+/* WAVEFORM mode CMR bits */
+#define ATMEL_TC_CPCSTOP (1 << 6) /* RC compare stops counter */
+#define ATMEL_TC_CPCDIS (1 << 7) /* RC compare disables counter */
+#define ATMEL_TC_EEVTEDG (3 << 8) /* external event edge */
+#define ATMEL_TC_EEVTEDG_NONE (0 << 8)
+#define ATMEL_TC_EEVTEDG_RISING (1 << 8)
+#define ATMEL_TC_EEVTEDG_FALLING (2 << 8)
+#define ATMEL_TC_EEVTEDG_BOTH (3 << 8)
+#define ATMEL_TC_EEVT (3 << 10) /* external event source */
+#define ATMEL_TC_EEVT_TIOB (0 << 10)
+#define ATMEL_TC_EEVT_XC0 (1 << 10)
+#define ATMEL_TC_EEVT_XC1 (2 << 10)
+#define ATMEL_TC_EEVT_XC2 (3 << 10)
+#define ATMEL_TC_ENETRG (1 << 12) /* external event is trigger */
+#define ATMEL_TC_WAVESEL (3 << 13) /* waveform type */
+#define ATMEL_TC_WAVESEL_UP (0 << 13)
+#define ATMEL_TC_WAVESEL_UPDOWN (1 << 13)
+#define ATMEL_TC_WAVESEL_UP_AUTO (2 << 13)
+#define ATMEL_TC_WAVESEL_UPDOWN_AUTO (3 << 13)
+#define ATMEL_TC_ACPA (3 << 16) /* RA compare changes TIOA */
+#define ATMEL_TC_ACPA_NONE (0 << 16)
+#define ATMEL_TC_ACPA_SET (1 << 16)
+#define ATMEL_TC_ACPA_CLEAR (2 << 16)
+#define ATMEL_TC_ACPA_TOGGLE (3 << 16)
+#define ATMEL_TC_ACPC (3 << 18) /* RC compare changes TIOA */
+#define ATMEL_TC_ACPC_NONE (0 << 18)
+#define ATMEL_TC_ACPC_SET (1 << 18)
+#define ATMEL_TC_ACPC_CLEAR (2 << 18)
+#define ATMEL_TC_ACPC_TOGGLE (3 << 18)
+#define ATMEL_TC_AEEVT (3 << 20) /* external event changes TIOA */
+#define ATMEL_TC_AEEVT_NONE (0 << 20)
+#define ATMEL_TC_AEEVT_SET (1 << 20)
+#define ATMEL_TC_AEEVT_CLEAR (2 << 20)
+#define ATMEL_TC_AEEVT_TOGGLE (3 << 20)
+#define ATMEL_TC_ASWTRG (3 << 22) /* software trigger changes TIOA */
+#define ATMEL_TC_ASWTRG_NONE (0 << 22)
+#define ATMEL_TC_ASWTRG_SET (1 << 22)
+#define ATMEL_TC_ASWTRG_CLEAR (2 << 22)
+#define ATMEL_TC_ASWTRG_TOGGLE (3 << 22)
+#define ATMEL_TC_BCPB (3 << 24) /* RB compare changes TIOB */
+#define ATMEL_TC_BCPB_NONE (0 << 24)
+#define ATMEL_TC_BCPB_SET (1 << 24)
+#define ATMEL_TC_BCPB_CLEAR (2 << 24)
+#define ATMEL_TC_BCPB_TOGGLE (3 << 24)
+#define ATMEL_TC_BCPC (3 << 26) /* RC compare changes TIOB */
+#define ATMEL_TC_BCPC_NONE (0 << 26)
+#define ATMEL_TC_BCPC_SET (1 << 26)
+#define ATMEL_TC_BCPC_CLEAR (2 << 26)
+#define ATMEL_TC_BCPC_TOGGLE (3 << 26)
+#define ATMEL_TC_BEEVT (3 << 28) /* external event changes TIOB */
+#define ATMEL_TC_BEEVT_NONE (0 << 28)
+#define ATMEL_TC_BEEVT_SET (1 << 28)
+#define ATMEL_TC_BEEVT_CLEAR (2 << 28)
+#define ATMEL_TC_BEEVT_TOGGLE (3 << 28)
+#define ATMEL_TC_BSWTRG (3 << 30) /* software trigger changes TIOB */
+#define ATMEL_TC_BSWTRG_NONE (0 << 30)
+#define ATMEL_TC_BSWTRG_SET (1 << 30)
+#define ATMEL_TC_BSWTRG_CLEAR (2 << 30)
+#define ATMEL_TC_BSWTRG_TOGGLE (3 << 30)
+
+#define ATMEL_TC_CV 0x10 /* counter Value */
+#define ATMEL_TC_RA 0x14 /* register A */
+#define ATMEL_TC_RB 0x18 /* register B */
+#define ATMEL_TC_RC 0x1c /* register C */
+
+#define ATMEL_TC_SR 0x20 /* status (read-only) */
+/* Status-only flags */
+#define ATMEL_TC_CLKSTA (1 << 16) /* clock enabled */
+#define ATMEL_TC_MTIOA (1 << 17) /* TIOA mirror */
+#define ATMEL_TC_MTIOB (1 << 18) /* TIOB mirror */
+
+#define ATMEL_TC_IER 0x24 /* interrupt enable (write-only) */
+#define ATMEL_TC_IDR 0x28 /* interrupt disable (write-only) */
+#define ATMEL_TC_IMR 0x2c /* interrupt mask (read-only) */
+
+/* Status and IRQ flags */
+#define ATMEL_TC_COVFS (1 << 0) /* counter overflow */
+#define ATMEL_TC_LOVRS (1 << 1) /* load overrun */
+#define ATMEL_TC_CPAS (1 << 2) /* RA compare */
+#define ATMEL_TC_CPBS (1 << 3) /* RB compare */
+#define ATMEL_TC_CPCS (1 << 4) /* RC compare */
+#define ATMEL_TC_LDRAS (1 << 5) /* RA loading */
+#define ATMEL_TC_LDRBS (1 << 6) /* RB loading */
+#define ATMEL_TC_ETRGS (1 << 7) /* external trigger */
+
+#endif
--- /dev/null
+/*
+ * Platform data definitions for Atmel USBA gadget driver.
+ */
+#ifndef __LINUX_USB_USBA_H
+#define __LINUX_USB_USBA_H
+
+struct usba_ep_data {
+ char *name;
+ int index;
+ int fifo_size;
+ int nr_banks;
+ int can_dma;
+ int can_isoc;
+};
+
+struct usba_platform_data {
+ int vbus_pin;
+ int num_ep;
+ struct usba_ep_data ep[0];
+};
+
+#endif /* __LINUX_USB_USBA_H */
projects / ~andy / linux / commitdiff