--- /dev/null
+ARM TCM (Tightly-Coupled Memory) handling in Linux
+----
+Written by Linus Walleij <linus.walleij@stericsson.com>
+
+Some ARM SoC:s have a so-called TCM (Tightly-Coupled Memory).
+This is usually just a few (4-64) KiB of RAM inside the ARM
+processor.
+
+Due to being embedded inside the CPU The TCM has a
+Harvard-architecture, so there is an ITCM (instruction TCM)
+and a DTCM (data TCM). The DTCM can not contain any
+instructions, but the ITCM can actually contain data.
+The size of DTCM or ITCM is minimum 4KiB so the typical
+minimum configuration is 4KiB ITCM and 4KiB DTCM.
+
+ARM CPU:s have special registers to read out status, physical
+location and size of TCM memories. arch/arm/include/asm/cputype.h
+defines a CPUID_TCM register that you can read out from the
+system control coprocessor. Documentation from ARM can be found
+at http://infocenter.arm.com, search for "TCM Status Register"
+to see documents for all CPUs. Reading this register you can
+determine if ITCM (bit 0) and/or DTCM (bit 16) is present in the
+machine.
+
+There is further a TCM region register (search for "TCM Region
+Registers" at the ARM site) that can report and modify the location
+size of TCM memories at runtime. This is used to read out and modify
+TCM location and size. Notice that this is not a MMU table: you
+actually move the physical location of the TCM around. At the
+place you put it, it will mask any underlying RAM from the
+CPU so it is usually wise not to overlap any physical RAM with
+the TCM. The TCM memory exists totally outside the MMU and will
+override any MMU mappings.
+
+Code executing inside the ITCM does not "see" any MMU mappings
+and e.g. register accesses must be made to physical addresses.
+
+TCM is used for a few things:
+
+- FIQ and other interrupt handlers that need deterministic
+ timing and cannot wait for cache misses.
+
+- Idle loops where all external RAM is set to self-refresh
+ retention mode, so only on-chip RAM is accessible by
+ the CPU and then we hang inside ITCM waiting for an
+ interrupt.
+
+- Other operations which implies shutting off or reconfiguring
+ the external RAM controller.
+
+There is an interface for using TCM on the ARM architecture
+in <asm/tcm.h>. Using this interface it is possible to:
+
+- Define the physical address and size of ITCM and DTCM.
+
+- Tag functions to be compiled into ITCM.
+
+- Tag data and constants to be allocated to DTCM and ITCM.
+
+- Have the remaining TCM RAM added to a special
+ allocation pool with gen_pool_create() and gen_pool_add()
+ and provice tcm_alloc() and tcm_free() for this
+ memory. Such a heap is great for things like saving
+ device state when shutting off device power domains.
+
+A machine that has TCM memory shall select HAVE_TCM in
+arch/arm/Kconfig for itself, and then the
+rest of the functionality will depend on the physical
+location and size of ITCM and DTCM to be defined in
+mach/memory.h for the machine. Code that needs to use
+TCM shall #include <asm/tcm.h> If the TCM is not located
+at the place given in memory.h it will be moved using
+the TCM Region registers.
+
+Functions to go into itcm can be tagged like this:
+int __tcmfunc foo(int bar);
+
+Variables to go into dtcm can be tagged like this:
+int __tcmdata foo;
+
+Constants can be tagged like this:
+int __tcmconst foo;
+
+To put assembler into TCM just use
+.section ".tcm.text" or .section ".tcm.data"
+respectively.
+
+Example code:
+
+#include <asm/tcm.h>
+
+/* Uninitialized data */
+static u32 __tcmdata tcmvar;
+/* Initialized data */
+static u32 __tcmdata tcmassigned = 0x2BADBABEU;
+/* Constant */
+static const u32 __tcmconst tcmconst = 0xCAFEBABEU;
+
+static void __tcmlocalfunc tcm_to_tcm(void)
+{
+ int i;
+ for (i = 0; i < 100; i++)
+ tcmvar ++;
+}
+
+static void __tcmfunc hello_tcm(void)
+{
+ /* Some abstract code that runs in ITCM */
+ int i;
+ for (i = 0; i < 100; i++) {
+ tcmvar ++;
+ }
+ tcm_to_tcm();
+}
+
+static void __init test_tcm(void)
+{
+ u32 *tcmem;
+ int i;
+
+ hello_tcm();
+ printk("Hello TCM executed from ITCM RAM\n");
+
+ printk("TCM variable from testrun: %u @ %p\n", tcmvar, &tcmvar);
+ tcmvar = 0xDEADBEEFU;
+ printk("TCM variable: 0x%x @ %p\n", tcmvar, &tcmvar);
+
+ printk("TCM assigned variable: 0x%x @ %p\n", tcmassigned, &tcmassigned);
+
+ printk("TCM constant: 0x%x @ %p\n", tcmconst, &tcmconst);
+
+ /* Allocate some TCM memory from the pool */
+ tcmem = tcm_alloc(20);
+ if (tcmem) {
+ printk("TCM Allocated 20 bytes of TCM @ %p\n", tcmem);
+ tcmem[0] = 0xDEADBEEFU;
+ tcmem[1] = 0x2BADBABEU;
+ tcmem[2] = 0xCAFEBABEU;
+ tcmem[3] = 0xDEADBEEFU;
+ tcmem[4] = 0x2BADBABEU;
+ for (i = 0; i < 5; i++)
+ printk("TCM tcmem[%d] = %08x\n", i, tcmem[i]);
+ tcm_free(tcmem, 20);
+ }
+}
ARM/INTEL IXP4XX ARM ARCHITECTURE
M: Imre Kaloz <kaloz@openwrt.org>
M: Krzysztof Halasa <khc@pm.waw.pl>
-L: linux-arm-kernel@lists.infradead.org
+L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
S: Maintained
F: arch/arm/mach-ixp4xx/
M: Dirk Opfer <dirk@opfer-online.de>
S: Maintained
-ARM/PALMTX,PALMT5,PALMLD,PALMTE2 SUPPORT
-M: Marek Vasut <marek.vasut@gmail.com>
+ARM/PALMTX,PALMT5,PALMLD,PALMTE2,PALMTC SUPPORT
+P: Marek Vasut
+M: marek.vasut@gmail.com
+L: linux-arm-kernel@lists.infradead.org
W: http://hackndev.com
S: Maintained
ARM/PALM TREO 680 SUPPORT
M: Tomas Cech <sleep_walker@suse.cz>
+L: linux-arm-kernel@lists.infradead.org
W: http://hackndev.com
S: Maintained
ARM/PALMZ72 SUPPORT
M: Sergey Lapin <slapin@ossfans.org>
+L: linux-arm-kernel@lists.infradead.org
W: http://hackndev.com
S: Maintained
depends on GENERIC_CLOCKEVENTS
default y if SMP && !LOCAL_TIMERS
+config HAVE_TCM
+ bool
+ select GENERIC_ALLOCATOR
+
config NO_IOPORT
bool
bool "ST-Ericsson U300 Series"
depends on MMU
select CPU_ARM926T
+ select HAVE_TCM
select ARM_AMBA
select ARM_VIC
select GENERIC_TIME
spin_unlock_irqrestore(&lchip->lock, flags);
}
+EXPORT_SYMBOL(locomo_gpio_set_dir);
int locomo_gpio_read_level(struct device *dev, unsigned int bits)
{
ret &= bits;
return ret;
}
+EXPORT_SYMBOL(locomo_gpio_read_level);
int locomo_gpio_read_output(struct device *dev, unsigned int bits)
{
ret &= bits;
return ret;
}
+EXPORT_SYMBOL(locomo_gpio_read_output);
void locomo_gpio_write(struct device *dev, unsigned int bits, unsigned int set)
{
spin_unlock_irqrestore(&lchip->lock, flags);
}
+EXPORT_SYMBOL(locomo_gpio_write);
static void locomo_m62332_sendbit(void *mapbase, int bit)
{
spin_unlock_irqrestore(&lchip->lock, flags);
}
+EXPORT_SYMBOL(locomo_m62332_senddata);
/*
* Frontlight control
*/
-static struct locomo *locomo_chip_driver(struct locomo_dev *ldev);
-
void locomo_frontlight_set(struct locomo_dev *dev, int duty, int vr, int bpwf)
{
unsigned long flags;
driver->drv.bus = &locomo_bus_type;
return driver_register(&driver->drv);
}
+EXPORT_SYMBOL(locomo_driver_register);
void locomo_driver_unregister(struct locomo_driver *driver)
{
driver_unregister(&driver->drv);
}
+EXPORT_SYMBOL(locomo_driver_unregister);
static int __init locomo_init(void)
{
MODULE_DESCRIPTION("Sharp LoCoMo core driver");
MODULE_LICENSE("GPL");
MODULE_AUTHOR("John Lenz <lenz@cs.wisc.edu>");
-
-EXPORT_SYMBOL(locomo_driver_register);
-EXPORT_SYMBOL(locomo_driver_unregister);
-EXPORT_SYMBOL(locomo_gpio_set_dir);
-EXPORT_SYMBOL(locomo_gpio_read_level);
-EXPORT_SYMBOL(locomo_gpio_read_output);
-EXPORT_SYMBOL(locomo_gpio_write);
-EXPORT_SYMBOL(locomo_m62332_senddata);
#include <linux/list.h>
#include <linux/io.h>
#include <linux/sysdev.h>
+#include <linux/device.h>
#include <linux/amba/bus.h>
#include <asm/mach/irq.h>
+++ /dev/null
-#
-# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.24-rc5
-# Fri Dec 21 11:06:19 2007
-#
-CONFIG_ARM=y
-CONFIG_SYS_SUPPORTS_APM_EMULATION=y
-CONFIG_GENERIC_GPIO=y
-CONFIG_GENERIC_TIME=y
-CONFIG_GENERIC_CLOCKEVENTS=y
-CONFIG_MMU=y
-# CONFIG_NO_IOPORT is not set
-CONFIG_GENERIC_HARDIRQS=y
-CONFIG_STACKTRACE_SUPPORT=y
-CONFIG_LOCKDEP_SUPPORT=y
-CONFIG_TRACE_IRQFLAGS_SUPPORT=y
-CONFIG_HARDIRQS_SW_RESEND=y
-CONFIG_GENERIC_IRQ_PROBE=y
-CONFIG_RWSEM_GENERIC_SPINLOCK=y
-# CONFIG_ARCH_HAS_ILOG2_U32 is not set
-# CONFIG_ARCH_HAS_ILOG2_U64 is not set
-CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
-CONFIG_ZONE_DMA=y
-CONFIG_ARCH_MTD_XIP=y
-CONFIG_VECTORS_BASE=0xffff0000
-CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
-
-#
-# General setup
-#
-CONFIG_EXPERIMENTAL=y
-CONFIG_BROKEN_ON_SMP=y
-CONFIG_LOCK_KERNEL=y
-CONFIG_INIT_ENV_ARG_LIMIT=32
-CONFIG_LOCALVERSION=""
-CONFIG_LOCALVERSION_AUTO=y
-CONFIG_SWAP=y
-CONFIG_SYSVIPC=y
-CONFIG_SYSVIPC_SYSCTL=y
-# CONFIG_POSIX_MQUEUE is not set
-# CONFIG_BSD_PROCESS_ACCT is not set
-# CONFIG_TASKSTATS is not set
-# CONFIG_USER_NS is not set
-# CONFIG_PID_NS is not set
-# CONFIG_AUDIT is not set
-# CONFIG_IKCONFIG is not set
-CONFIG_LOG_BUF_SHIFT=14
-# CONFIG_CGROUPS is not set
-CONFIG_FAIR_GROUP_SCHED=y
-CONFIG_FAIR_USER_SCHED=y
-# CONFIG_FAIR_CGROUP_SCHED is not set
-CONFIG_SYSFS_DEPRECATED=y
-# CONFIG_RELAY is not set
-CONFIG_BLK_DEV_INITRD=y
-CONFIG_INITRAMFS_SOURCE=""
-CONFIG_CC_OPTIMIZE_FOR_SIZE=y
-CONFIG_SYSCTL=y
-# CONFIG_EMBEDDED is not set
-CONFIG_UID16=y
-CONFIG_SYSCTL_SYSCALL=y
-CONFIG_KALLSYMS=y
-# CONFIG_KALLSYMS_ALL is not set
-# CONFIG_KALLSYMS_EXTRA_PASS is not set
-CONFIG_HOTPLUG=y
-CONFIG_PRINTK=y
-CONFIG_BUG=y
-CONFIG_ELF_CORE=y
-CONFIG_BASE_FULL=y
-CONFIG_FUTEX=y
-CONFIG_ANON_INODES=y
-CONFIG_EPOLL=y
-CONFIG_SIGNALFD=y
-CONFIG_EVENTFD=y
-CONFIG_SHMEM=y
-CONFIG_VM_EVENT_COUNTERS=y
-CONFIG_SLAB=y
-# CONFIG_SLUB is not set
-# CONFIG_SLOB is not set
-CONFIG_RT_MUTEXES=y
-# CONFIG_TINY_SHMEM is not set
-CONFIG_BASE_SMALL=0
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-CONFIG_MODULE_FORCE_UNLOAD=y
-# CONFIG_MODVERSIONS is not set
-# CONFIG_MODULE_SRCVERSION_ALL is not set
-# CONFIG_KMOD is not set
-CONFIG_BLOCK=y
-# CONFIG_LBD is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
-# CONFIG_LSF is not set
-# CONFIG_BLK_DEV_BSG is not set
-
-#
-# IO Schedulers
-#
-CONFIG_IOSCHED_NOOP=y
-CONFIG_IOSCHED_AS=y
-CONFIG_IOSCHED_DEADLINE=y
-CONFIG_IOSCHED_CFQ=y
-# CONFIG_DEFAULT_AS is not set
-# CONFIG_DEFAULT_DEADLINE is not set
-CONFIG_DEFAULT_CFQ=y
-# CONFIG_DEFAULT_NOOP is not set
-CONFIG_DEFAULT_IOSCHED="cfq"
-
-#
-# System Type
-#
-# CONFIG_ARCH_AAEC2000 is not set
-# CONFIG_ARCH_INTEGRATOR is not set
-# CONFIG_ARCH_REALVIEW is not set
-# CONFIG_ARCH_VERSATILE is not set
-# CONFIG_ARCH_AT91 is not set
-# CONFIG_ARCH_CLPS7500 is not set
-# CONFIG_ARCH_CLPS711X is not set
-# CONFIG_ARCH_CO285 is not set
-# CONFIG_ARCH_EBSA110 is not set
-# CONFIG_ARCH_EP93XX is not set
-# CONFIG_ARCH_FOOTBRIDGE is not set
-# CONFIG_ARCH_NETX is not set
-# CONFIG_ARCH_H720X is not set
-# CONFIG_ARCH_IMX is not set
-# CONFIG_ARCH_IOP13XX is not set
-# CONFIG_ARCH_IOP32X is not set
-# CONFIG_ARCH_IOP33X is not set
-# CONFIG_ARCH_IXP23XX is not set
-# CONFIG_ARCH_IXP2000 is not set
-# CONFIG_ARCH_IXP4XX is not set
-# CONFIG_ARCH_L7200 is not set
-# CONFIG_ARCH_KS8695 is not set
-# CONFIG_ARCH_NS9XXX is not set
-# CONFIG_ARCH_MXC is not set
-# CONFIG_ARCH_PNX4008 is not set
-CONFIG_ARCH_PXA=y
-# CONFIG_ARCH_RPC is not set
-# CONFIG_ARCH_SA1100 is not set
-# CONFIG_ARCH_S3C2410 is not set
-# CONFIG_ARCH_SHARK is not set
-# CONFIG_ARCH_LH7A40X is not set
-# CONFIG_ARCH_DAVINCI is not set
-# CONFIG_ARCH_OMAP is not set
-
-#
-# Intel PXA2xx/PXA3xx Implementations
-#
-
-#
-# Supported PXA3xx Processor Variants
-#
-CONFIG_CPU_PXA300=y
-CONFIG_CPU_PXA310=y
-# CONFIG_CPU_PXA320 is not set
-# CONFIG_ARCH_LUBBOCK is not set
-# CONFIG_MACH_LOGICPD_PXA270 is not set
-# CONFIG_MACH_MAINSTONE is not set
-# CONFIG_ARCH_PXA_IDP is not set
-# CONFIG_PXA_SHARPSL is not set
-# CONFIG_MACH_TRIZEPS4 is not set
-# CONFIG_MACH_EM_X270 is not set
-# CONFIG_MACH_ZYLONITE is not set
-CONFIG_MACH_LITTLETON=y
-# CONFIG_MACH_ARMCORE is not set
-CONFIG_PXA3xx=y
-CONFIG_PXA_SSP=y
-
-#
-# Boot options
-#
-
-#
-# Power management
-#
-
-#
-# Processor Type
-#
-CONFIG_CPU_32=y
-CONFIG_CPU_XSC3=y
-CONFIG_CPU_32v5=y
-CONFIG_CPU_ABRT_EV5T=y
-CONFIG_CPU_CACHE_VIVT=y
-CONFIG_CPU_TLB_V4WBI=y
-CONFIG_CPU_CP15=y
-CONFIG_CPU_CP15_MMU=y
-CONFIG_IO_36=y
-
-#
-# Processor Features
-#
-# CONFIG_ARM_THUMB is not set
-# CONFIG_CPU_DCACHE_DISABLE is not set
-# CONFIG_CPU_BPREDICT_DISABLE is not set
-# CONFIG_OUTER_CACHE is not set
-CONFIG_IWMMXT=y
-
-#
-# Bus support
-#
-# CONFIG_PCI_SYSCALL is not set
-# CONFIG_ARCH_SUPPORTS_MSI is not set
-# CONFIG_PCCARD is not set
-
-#
-# Kernel Features
-#
-CONFIG_TICK_ONESHOT=y
-# CONFIG_NO_HZ is not set
-# CONFIG_HIGH_RES_TIMERS is not set
-CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
-CONFIG_PREEMPT=y
-CONFIG_HZ=100
-CONFIG_AEABI=y
-CONFIG_OABI_COMPAT=y
-# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set
-CONFIG_SELECT_MEMORY_MODEL=y
-CONFIG_FLATMEM_MANUAL=y
-# CONFIG_DISCONTIGMEM_MANUAL is not set
-# CONFIG_SPARSEMEM_MANUAL is not set
-CONFIG_FLATMEM=y
-CONFIG_FLAT_NODE_MEM_MAP=y
-# CONFIG_SPARSEMEM_STATIC is not set
-# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
-CONFIG_SPLIT_PTLOCK_CPUS=4096
-# CONFIG_RESOURCES_64BIT is not set
-CONFIG_ZONE_DMA_FLAG=1
-CONFIG_BOUNCE=y
-CONFIG_VIRT_TO_BUS=y
-CONFIG_ALIGNMENT_TRAP=y
-
-#
-# Boot options
-#
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_CMDLINE="root=/dev/nfs rootfstype=nfs nfsroot=192.168.1.100:/nfsroot/ ip=192.168.1.101:192.168.1.100::255.255.255.0::eth0:on console=ttyS2,38400 mem=64M"
-# CONFIG_XIP_KERNEL is not set
-# CONFIG_KEXEC is not set
-
-#
-# CPU Frequency scaling
-#
-# CONFIG_CPU_FREQ is not set
-
-#
-# Floating point emulation
-#
-
-#
-# At least one emulation must be selected
-#
-CONFIG_FPE_NWFPE=y
-# CONFIG_FPE_NWFPE_XP is not set
-# CONFIG_FPE_FASTFPE is not set
-
-#
-# Userspace binary formats
-#
-CONFIG_BINFMT_ELF=y
-# CONFIG_BINFMT_AOUT is not set
-# CONFIG_BINFMT_MISC is not set
-
-#
-# Power management options
-#
-# CONFIG_PM is not set
-CONFIG_SUSPEND_UP_POSSIBLE=y
-
-#
-# Networking
-#
-CONFIG_NET=y
-
-#
-# Networking options
-#
-CONFIG_PACKET=y
-# CONFIG_PACKET_MMAP is not set
-CONFIG_UNIX=y
-CONFIG_XFRM=y
-# CONFIG_XFRM_USER is not set
-# CONFIG_XFRM_SUB_POLICY is not set
-# CONFIG_XFRM_MIGRATE is not set
-# CONFIG_NET_KEY is not set
-CONFIG_INET=y
-# CONFIG_IP_MULTICAST is not set
-# CONFIG_IP_ADVANCED_ROUTER is not set
-CONFIG_IP_FIB_HASH=y
-CONFIG_IP_PNP=y
-# CONFIG_IP_PNP_DHCP is not set
-# CONFIG_IP_PNP_BOOTP is not set
-# CONFIG_IP_PNP_RARP is not set
-# CONFIG_NET_IPIP is not set
-# CONFIG_NET_IPGRE is not set
-# CONFIG_ARPD is not set
-# CONFIG_SYN_COOKIES is not set
-# CONFIG_INET_AH is not set
-# CONFIG_INET_ESP is not set
-# CONFIG_INET_IPCOMP is not set
-# CONFIG_INET_XFRM_TUNNEL is not set
-# CONFIG_INET_TUNNEL is not set
-CONFIG_INET_XFRM_MODE_TRANSPORT=y
-CONFIG_INET_XFRM_MODE_TUNNEL=y
-CONFIG_INET_XFRM_MODE_BEET=y
-# CONFIG_INET_LRO is not set
-CONFIG_INET_DIAG=y
-CONFIG_INET_TCP_DIAG=y
-# CONFIG_TCP_CONG_ADVANCED is not set
-CONFIG_TCP_CONG_CUBIC=y
-CONFIG_DEFAULT_TCP_CONG="cubic"
-# CONFIG_TCP_MD5SIG is not set
-# CONFIG_IPV6 is not set
-# CONFIG_INET6_XFRM_TUNNEL is not set
-# CONFIG_INET6_TUNNEL is not set
-# CONFIG_NETWORK_SECMARK is not set
-# CONFIG_NETFILTER is not set
-# CONFIG_IP_DCCP is not set
-# CONFIG_IP_SCTP is not set
-# CONFIG_TIPC is not set
-# CONFIG_ATM is not set
-# CONFIG_BRIDGE is not set
-# CONFIG_VLAN_8021Q is not set
-# CONFIG_DECNET is not set
-# CONFIG_LLC2 is not set
-# CONFIG_IPX is not set
-# CONFIG_ATALK is not set
-# CONFIG_X25 is not set
-# CONFIG_LAPB is not set
-# CONFIG_ECONET is not set
-# CONFIG_WAN_ROUTER is not set
-# CONFIG_NET_SCHED is not set
-
-#
-# Network testing
-#
-# CONFIG_NET_PKTGEN is not set
-# CONFIG_HAMRADIO is not set
-# CONFIG_IRDA is not set
-# CONFIG_BT is not set
-# CONFIG_AF_RXRPC is not set
-
-#
-# Wireless
-#
-# CONFIG_CFG80211 is not set
-# CONFIG_WIRELESS_EXT is not set
-# CONFIG_MAC80211 is not set
-# CONFIG_IEEE80211 is not set
-# CONFIG_RFKILL is not set
-# CONFIG_NET_9P is not set
-
-#
-# Device Drivers
-#
-
-#
-# Generic Driver Options
-#
-CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
-# CONFIG_STANDALONE is not set
-# CONFIG_PREVENT_FIRMWARE_BUILD is not set
-CONFIG_FW_LOADER=y
-# CONFIG_DEBUG_DRIVER is not set
-# CONFIG_DEBUG_DEVRES is not set
-# CONFIG_SYS_HYPERVISOR is not set
-# CONFIG_CONNECTOR is not set
-# CONFIG_MTD is not set
-# CONFIG_PARPORT is not set
-# CONFIG_BLK_DEV is not set
-# CONFIG_MISC_DEVICES is not set
-# CONFIG_IDE is not set
-
-#
-# SCSI device support
-#
-# CONFIG_RAID_ATTRS is not set
-# CONFIG_SCSI is not set
-# CONFIG_SCSI_DMA is not set
-# CONFIG_SCSI_NETLINK is not set
-# CONFIG_ATA is not set
-# CONFIG_MD is not set
-CONFIG_NETDEVICES=y
-# CONFIG_NETDEVICES_MULTIQUEUE is not set
-# CONFIG_DUMMY is not set
-# CONFIG_BONDING is not set
-# CONFIG_MACVLAN is not set
-# CONFIG_EQUALIZER is not set
-# CONFIG_TUN is not set
-# CONFIG_VETH is not set
-# CONFIG_PHYLIB is not set
-CONFIG_NET_ETHERNET=y
-CONFIG_MII=y
-# CONFIG_AX88796 is not set
-CONFIG_SMC91X=y
-# CONFIG_DM9000 is not set
-# CONFIG_SMC911X is not set
-# CONFIG_IBM_NEW_EMAC_ZMII is not set
-# CONFIG_IBM_NEW_EMAC_RGMII is not set
-# CONFIG_IBM_NEW_EMAC_TAH is not set
-# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
-# CONFIG_B44 is not set
-# CONFIG_NETDEV_1000 is not set
-# CONFIG_NETDEV_10000 is not set
-
-#
-# Wireless LAN
-#
-# CONFIG_WLAN_PRE80211 is not set
-# CONFIG_WLAN_80211 is not set
-# CONFIG_WAN is not set
-# CONFIG_PPP is not set
-# CONFIG_SLIP is not set
-# CONFIG_SHAPER is not set
-# CONFIG_NETCONSOLE is not set
-# CONFIG_NETPOLL is not set
-# CONFIG_NET_POLL_CONTROLLER is not set
-# CONFIG_ISDN is not set
-
-#
-# Input device support
-#
-CONFIG_INPUT=y
-# CONFIG_INPUT_FF_MEMLESS is not set
-# CONFIG_INPUT_POLLDEV is not set
-
-#
-# Userland interfaces
-#
-CONFIG_INPUT_MOUSEDEV=y
-# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
-CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
-CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
-# CONFIG_INPUT_JOYDEV is not set
-# CONFIG_INPUT_EVDEV is not set
-# CONFIG_INPUT_EVBUG is not set
-
-#
-# Input Device Drivers
-#
-# CONFIG_INPUT_KEYBOARD is not set
-# CONFIG_INPUT_MOUSE is not set
-# CONFIG_INPUT_JOYSTICK is not set
-# CONFIG_INPUT_TABLET is not set
-# CONFIG_INPUT_TOUCHSCREEN is not set
-# CONFIG_INPUT_MISC is not set
-
-#
-# Hardware I/O ports
-#
-# CONFIG_SERIO is not set
-# CONFIG_GAMEPORT is not set
-
-#
-# Character devices
-#
-CONFIG_VT=y
-CONFIG_VT_CONSOLE=y
-CONFIG_HW_CONSOLE=y
-# CONFIG_VT_HW_CONSOLE_BINDING is not set
-# CONFIG_SERIAL_NONSTANDARD is not set
-
-#
-# Serial drivers
-#
-# CONFIG_SERIAL_8250 is not set
-
-#
-# Non-8250 serial port support
-#
-CONFIG_SERIAL_PXA=y
-CONFIG_SERIAL_PXA_CONSOLE=y
-CONFIG_SERIAL_CORE=y
-CONFIG_SERIAL_CORE_CONSOLE=y
-CONFIG_UNIX98_PTYS=y
-# CONFIG_LEGACY_PTYS is not set
-# CONFIG_IPMI_HANDLER is not set
-# CONFIG_HW_RANDOM is not set
-# CONFIG_NVRAM is not set
-# CONFIG_R3964 is not set
-# CONFIG_RAW_DRIVER is not set
-# CONFIG_TCG_TPM is not set
-# CONFIG_I2C is not set
-
-#
-# SPI support
-#
-# CONFIG_SPI is not set
-# CONFIG_SPI_MASTER is not set
-# CONFIG_W1 is not set
-# CONFIG_POWER_SUPPLY is not set
-# CONFIG_HWMON is not set
-# CONFIG_WATCHDOG is not set
-
-#
-# Sonics Silicon Backplane
-#
-CONFIG_SSB_POSSIBLE=y
-# CONFIG_SSB is not set
-
-#
-# Multifunction device drivers
-#
-# CONFIG_MFD_SM501 is not set
-
-#
-# Multimedia devices
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_DAB is not set
-
-#
-# Graphics support
-#
-# CONFIG_VGASTATE is not set
-# CONFIG_VIDEO_OUTPUT_CONTROL is not set
-CONFIG_FB=y
-# CONFIG_FIRMWARE_EDID is not set
-# CONFIG_FB_DDC is not set
-CONFIG_FB_CFB_FILLRECT=y
-CONFIG_FB_CFB_COPYAREA=y
-CONFIG_FB_CFB_IMAGEBLIT=y
-# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
-# CONFIG_FB_SYS_FILLRECT is not set
-# CONFIG_FB_SYS_COPYAREA is not set
-# CONFIG_FB_SYS_IMAGEBLIT is not set
-# CONFIG_FB_SYS_FOPS is not set
-CONFIG_FB_DEFERRED_IO=y
-# CONFIG_FB_SVGALIB is not set
-# CONFIG_FB_MACMODES is not set
-# CONFIG_FB_BACKLIGHT is not set
-# CONFIG_FB_MODE_HELPERS is not set
-# CONFIG_FB_TILEBLITTING is not set
-
-#
-# Frame buffer hardware drivers
-#
-# CONFIG_FB_S1D13XXX is not set
-CONFIG_FB_PXA=y
-# CONFIG_FB_PXA_PARAMETERS is not set
-# CONFIG_FB_MBX is not set
-# CONFIG_FB_VIRTUAL is not set
-# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
-
-#
-# Display device support
-#
-# CONFIG_DISPLAY_SUPPORT is not set
-
-#
-# Console display driver support
-#
-# CONFIG_VGA_CONSOLE is not set
-CONFIG_DUMMY_CONSOLE=y
-CONFIG_FRAMEBUFFER_CONSOLE=y
-# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set
-# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
-CONFIG_FONTS=y
-# CONFIG_FONT_8x8 is not set
-CONFIG_FONT_8x16=y
-# CONFIG_FONT_6x11 is not set
-# CONFIG_FONT_7x14 is not set
-# CONFIG_FONT_PEARL_8x8 is not set
-# CONFIG_FONT_ACORN_8x8 is not set
-# CONFIG_FONT_MINI_4x6 is not set
-# CONFIG_FONT_SUN8x16 is not set
-# CONFIG_FONT_SUN12x22 is not set
-# CONFIG_FONT_10x18 is not set
-CONFIG_LOGO=y
-CONFIG_LOGO_LINUX_MONO=y
-CONFIG_LOGO_LINUX_VGA16=y
-CONFIG_LOGO_LINUX_CLUT224=y
-
-#
-# Sound
-#
-# CONFIG_SOUND is not set
-# CONFIG_HID_SUPPORT is not set
-# CONFIG_USB_SUPPORT is not set
-# CONFIG_MMC is not set
-# CONFIG_NEW_LEDS is not set
-CONFIG_RTC_LIB=y
-# CONFIG_RTC_CLASS is not set
-
-#
-# File systems
-#
-# CONFIG_EXT2_FS is not set
-# CONFIG_EXT3_FS is not set
-# CONFIG_EXT4DEV_FS is not set
-# CONFIG_REISERFS_FS is not set
-# CONFIG_JFS_FS is not set
-CONFIG_FS_POSIX_ACL=y
-# CONFIG_XFS_FS is not set
-# CONFIG_GFS2_FS is not set
-# CONFIG_OCFS2_FS is not set
-# CONFIG_MINIX_FS is not set
-# CONFIG_ROMFS_FS is not set
-# CONFIG_INOTIFY is not set
-# CONFIG_QUOTA is not set
-# CONFIG_DNOTIFY is not set
-# CONFIG_AUTOFS_FS is not set
-# CONFIG_AUTOFS4_FS is not set
-# CONFIG_FUSE_FS is not set
-
-#
-# CD-ROM/DVD Filesystems
-#
-# CONFIG_ISO9660_FS is not set
-# CONFIG_UDF_FS is not set
-
-#
-# DOS/FAT/NT Filesystems
-#
-# CONFIG_MSDOS_FS is not set
-# CONFIG_VFAT_FS is not set
-# CONFIG_NTFS_FS is not set
-
-#
-# Pseudo filesystems
-#
-CONFIG_PROC_FS=y
-CONFIG_PROC_SYSCTL=y
-CONFIG_SYSFS=y
-# CONFIG_TMPFS is not set
-# CONFIG_HUGETLB_PAGE is not set
-# CONFIG_CONFIGFS_FS is not set
-
-#
-# Miscellaneous filesystems
-#
-# CONFIG_ADFS_FS is not set
-# CONFIG_AFFS_FS is not set
-# CONFIG_HFS_FS is not set
-# CONFIG_HFSPLUS_FS is not set
-# CONFIG_BEFS_FS is not set
-# CONFIG_BFS_FS is not set
-# CONFIG_EFS_FS is not set
-# CONFIG_CRAMFS is not set
-# CONFIG_VXFS_FS is not set
-# CONFIG_HPFS_FS is not set
-# CONFIG_QNX4FS_FS is not set
-# CONFIG_SYSV_FS is not set
-# CONFIG_UFS_FS is not set
-CONFIG_NETWORK_FILESYSTEMS=y
-CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
-CONFIG_NFS_V3_ACL=y
-CONFIG_NFS_V4=y
-CONFIG_NFS_DIRECTIO=y
-# CONFIG_NFSD is not set
-CONFIG_ROOT_NFS=y
-CONFIG_LOCKD=y
-CONFIG_LOCKD_V4=y
-CONFIG_NFS_ACL_SUPPORT=y
-CONFIG_NFS_COMMON=y
-CONFIG_SUNRPC=y
-CONFIG_SUNRPC_GSS=y
-# CONFIG_SUNRPC_BIND34 is not set
-CONFIG_RPCSEC_GSS_KRB5=y
-# CONFIG_RPCSEC_GSS_SPKM3 is not set
-# CONFIG_SMB_FS is not set
-# CONFIG_CIFS is not set
-# CONFIG_NCP_FS is not set
-# CONFIG_CODA_FS is not set
-# CONFIG_AFS_FS is not set
-
-#
-# Partition Types
-#
-# CONFIG_PARTITION_ADVANCED is not set
-CONFIG_MSDOS_PARTITION=y
-# CONFIG_NLS is not set
-# CONFIG_DLM is not set
-# CONFIG_INSTRUMENTATION is not set
-
-#
-# Kernel hacking
-#
-CONFIG_PRINTK_TIME=y
-CONFIG_ENABLE_WARN_DEPRECATED=y
-CONFIG_ENABLE_MUST_CHECK=y
-CONFIG_MAGIC_SYSRQ=y
-# CONFIG_UNUSED_SYMBOLS is not set
-# CONFIG_DEBUG_FS is not set
-# CONFIG_HEADERS_CHECK is not set
-CONFIG_DEBUG_KERNEL=y
-# CONFIG_DEBUG_SHIRQ is not set
-CONFIG_DETECT_SOFTLOCKUP=y
-CONFIG_SCHED_DEBUG=y
-# CONFIG_SCHEDSTATS is not set
-# CONFIG_TIMER_STATS is not set
-# CONFIG_DEBUG_SLAB is not set
-# CONFIG_DEBUG_PREEMPT is not set
-# CONFIG_DEBUG_RT_MUTEXES is not set
-# CONFIG_RT_MUTEX_TESTER is not set
-# CONFIG_DEBUG_SPINLOCK is not set
-# CONFIG_DEBUG_MUTEXES is not set
-# CONFIG_DEBUG_LOCK_ALLOC is not set
-# CONFIG_PROVE_LOCKING is not set
-# CONFIG_LOCK_STAT is not set
-# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
-# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
-# CONFIG_DEBUG_KOBJECT is not set
-CONFIG_DEBUG_BUGVERBOSE=y
-CONFIG_DEBUG_INFO=y
-# CONFIG_DEBUG_VM is not set
-# CONFIG_DEBUG_LIST is not set
-# CONFIG_DEBUG_SG is not set
-CONFIG_FRAME_POINTER=y
-CONFIG_FORCED_INLINING=y
-# CONFIG_BOOT_PRINTK_DELAY is not set
-# CONFIG_RCU_TORTURE_TEST is not set
-# CONFIG_FAULT_INJECTION is not set
-# CONFIG_SAMPLES is not set
-CONFIG_DEBUG_USER=y
-CONFIG_DEBUG_ERRORS=y
-CONFIG_DEBUG_LL=y
-# CONFIG_DEBUG_ICEDCC is not set
-
-#
-# Security options
-#
-# CONFIG_KEYS is not set
-# CONFIG_SECURITY is not set
-# CONFIG_SECURITY_FILE_CAPABILITIES is not set
-CONFIG_CRYPTO=y
-CONFIG_CRYPTO_ALGAPI=y
-CONFIG_CRYPTO_BLKCIPHER=y
-CONFIG_CRYPTO_MANAGER=y
-# CONFIG_CRYPTO_HMAC is not set
-# CONFIG_CRYPTO_XCBC is not set
-# CONFIG_CRYPTO_NULL is not set
-# CONFIG_CRYPTO_MD4 is not set
-CONFIG_CRYPTO_MD5=y
-# CONFIG_CRYPTO_SHA1 is not set
-# CONFIG_CRYPTO_SHA256 is not set
-# CONFIG_CRYPTO_SHA512 is not set
-# CONFIG_CRYPTO_WP512 is not set
-# CONFIG_CRYPTO_TGR192 is not set
-# CONFIG_CRYPTO_GF128MUL is not set
-# CONFIG_CRYPTO_ECB is not set
-CONFIG_CRYPTO_CBC=y
-# CONFIG_CRYPTO_PCBC is not set
-# CONFIG_CRYPTO_LRW is not set
-# CONFIG_CRYPTO_XTS is not set
-# CONFIG_CRYPTO_CRYPTD is not set
-CONFIG_CRYPTO_DES=y
-# CONFIG_CRYPTO_FCRYPT is not set
-# CONFIG_CRYPTO_BLOWFISH is not set
-# CONFIG_CRYPTO_TWOFISH is not set
-# CONFIG_CRYPTO_SERPENT is not set
-# CONFIG_CRYPTO_AES is not set
-# CONFIG_CRYPTO_CAST5 is not set
-# CONFIG_CRYPTO_CAST6 is not set
-# CONFIG_CRYPTO_TEA is not set
-# CONFIG_CRYPTO_ARC4 is not set
-# CONFIG_CRYPTO_KHAZAD is not set
-# CONFIG_CRYPTO_ANUBIS is not set
-# CONFIG_CRYPTO_SEED is not set
-# CONFIG_CRYPTO_DEFLATE is not set
-# CONFIG_CRYPTO_MICHAEL_MIC is not set
-# CONFIG_CRYPTO_CRC32C is not set
-# CONFIG_CRYPTO_CAMELLIA is not set
-# CONFIG_CRYPTO_TEST is not set
-# CONFIG_CRYPTO_AUTHENC is not set
-CONFIG_CRYPTO_HW=y
-
-#
-# Library routines
-#
-CONFIG_BITREVERSE=y
-CONFIG_CRC_CCITT=y
-# CONFIG_CRC16 is not set
-# CONFIG_CRC_ITU_T is not set
-CONFIG_CRC32=y
-# CONFIG_CRC7 is not set
-# CONFIG_LIBCRC32C is not set
-CONFIG_PLIST=y
-CONFIG_HAS_IOMEM=y
-CONFIG_HAS_IOPORT=y
-CONFIG_HAS_DMA=y
--- /dev/null
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.31-rc1
+# Mon Jul 13 22:48:49 2009
+#
+CONFIG_ARM=y
+CONFIG_HAVE_PWM=y
+CONFIG_SYS_SUPPORTS_APM_EMULATION=y
+CONFIG_GENERIC_GPIO=y
+CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_MMU=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_STACKTRACE_SUPPORT=y
+CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_LOCKDEP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
+CONFIG_HARDIRQS_SW_RESEND=y
+CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_RWSEM_GENERIC_SPINLOCK=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_ARCH_MTD_XIP=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
+CONFIG_VECTORS_BASE=0xffff0000
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
+
+#
+# General setup
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_LOCK_KERNEL=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+CONFIG_SWAP=y
+CONFIG_SYSVIPC=y
+CONFIG_SYSVIPC_SYSCTL=y
+# CONFIG_POSIX_MQUEUE is not set
+# CONFIG_BSD_PROCESS_ACCT is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_AUDIT is not set
+
+#
+# RCU Subsystem
+#
+# CONFIG_CLASSIC_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
+# CONFIG_TREE_RCU_TRACE is not set
+# CONFIG_PREEMPT_RCU_TRACE is not set
+# CONFIG_IKCONFIG is not set
+CONFIG_LOG_BUF_SHIFT=18
+CONFIG_GROUP_SCHED=y
+CONFIG_FAIR_GROUP_SCHED=y
+# CONFIG_RT_GROUP_SCHED is not set
+CONFIG_USER_SCHED=y
+# CONFIG_CGROUP_SCHED is not set
+# CONFIG_CGROUPS is not set
+CONFIG_SYSFS_DEPRECATED=y
+CONFIG_SYSFS_DEPRECATED_V2=y
+# CONFIG_RELAY is not set
+CONFIG_NAMESPACES=y
+# CONFIG_UTS_NS is not set
+# CONFIG_IPC_NS is not set
+# CONFIG_USER_NS is not set
+# CONFIG_PID_NS is not set
+# CONFIG_NET_NS is not set
+# CONFIG_BLK_DEV_INITRD is not set
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_SYSCTL=y
+CONFIG_ANON_INODES=y
+# CONFIG_EMBEDDED is not set
+CONFIG_UID16=y
+CONFIG_SYSCTL_SYSCALL=y
+CONFIG_KALLSYMS=y
+CONFIG_KALLSYMS_ALL=y
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
+CONFIG_SHMEM=y
+CONFIG_AIO=y
+
+#
+# Performance Counters
+#
+CONFIG_VM_EVENT_COUNTERS=y
+# CONFIG_STRIP_ASM_SYMS is not set
+CONFIG_COMPAT_BRK=y
+CONFIG_SLAB=y
+# CONFIG_SLUB is not set
+# CONFIG_SLOB is not set
+# CONFIG_PROFILING is not set
+# CONFIG_MARKERS is not set
+CONFIG_HAVE_OPROFILE=y
+# CONFIG_KPROBES is not set
+CONFIG_HAVE_KPROBES=y
+CONFIG_HAVE_KRETPROBES=y
+CONFIG_HAVE_CLK=y
+
+#
+# GCOV-based kernel profiling
+#
+# CONFIG_SLOW_WORK is not set
+CONFIG_HAVE_GENERIC_DMA_COHERENT=y
+CONFIG_SLABINFO=y
+CONFIG_RT_MUTEXES=y
+CONFIG_BASE_SMALL=0
+CONFIG_MODULES=y
+# CONFIG_MODULE_FORCE_LOAD is not set
+# CONFIG_MODULE_UNLOAD is not set
+# CONFIG_MODVERSIONS is not set
+# CONFIG_MODULE_SRCVERSION_ALL is not set
+CONFIG_BLOCK=y
+CONFIG_LBDAF=y
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_BLK_DEV_INTEGRITY is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_AS=y
+CONFIG_IOSCHED_DEADLINE=y
+CONFIG_IOSCHED_CFQ=y
+# CONFIG_DEFAULT_AS is not set
+# CONFIG_DEFAULT_DEADLINE is not set
+CONFIG_DEFAULT_CFQ=y
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="cfq"
+# CONFIG_FREEZER is not set
+
+#
+# System Type
+#
+# CONFIG_ARCH_AAEC2000 is not set
+# CONFIG_ARCH_INTEGRATOR is not set
+# CONFIG_ARCH_REALVIEW is not set
+# CONFIG_ARCH_VERSATILE is not set
+# CONFIG_ARCH_AT91 is not set
+# CONFIG_ARCH_CLPS711X is not set
+# CONFIG_ARCH_GEMINI is not set
+# CONFIG_ARCH_EBSA110 is not set
+# CONFIG_ARCH_EP93XX is not set
+# CONFIG_ARCH_FOOTBRIDGE is not set
+# CONFIG_ARCH_MXC is not set
+# CONFIG_ARCH_STMP3XXX is not set
+# CONFIG_ARCH_NETX is not set
+# CONFIG_ARCH_H720X is not set
+# CONFIG_ARCH_IOP13XX is not set
+# CONFIG_ARCH_IOP32X is not set
+# CONFIG_ARCH_IOP33X is not set
+# CONFIG_ARCH_IXP23XX is not set
+# CONFIG_ARCH_IXP2000 is not set
+# CONFIG_ARCH_IXP4XX is not set
+# CONFIG_ARCH_L7200 is not set
+# CONFIG_ARCH_KIRKWOOD is not set
+# CONFIG_ARCH_LOKI is not set
+# CONFIG_ARCH_MV78XX0 is not set
+# CONFIG_ARCH_ORION5X is not set
+# CONFIG_ARCH_MMP is not set
+# CONFIG_ARCH_KS8695 is not set
+# CONFIG_ARCH_NS9XXX is not set
+# CONFIG_ARCH_W90X900 is not set
+# CONFIG_ARCH_PNX4008 is not set
+CONFIG_ARCH_PXA=y
+# CONFIG_ARCH_MSM is not set
+# CONFIG_ARCH_RPC is not set
+# CONFIG_ARCH_SA1100 is not set
+# CONFIG_ARCH_S3C2410 is not set
+# CONFIG_ARCH_S3C64XX is not set
+# CONFIG_ARCH_SHARK is not set
+# CONFIG_ARCH_LH7A40X is not set
+# CONFIG_ARCH_U300 is not set
+# CONFIG_ARCH_DAVINCI is not set
+# CONFIG_ARCH_OMAP is not set
+
+#
+# Intel PXA2xx/PXA3xx Implementations
+#
+
+#
+# Supported PXA3xx Processor Variants
+#
+CONFIG_CPU_PXA300=y
+CONFIG_CPU_PXA310=y
+CONFIG_CPU_PXA320=y
+CONFIG_CPU_PXA930=y
+CONFIG_CPU_PXA935=y
+# CONFIG_ARCH_GUMSTIX is not set
+# CONFIG_MACH_INTELMOTE2 is not set
+# CONFIG_MACH_STARGATE2 is not set
+# CONFIG_ARCH_LUBBOCK is not set
+# CONFIG_MACH_LOGICPD_PXA270 is not set
+# CONFIG_MACH_MAINSTONE is not set
+# CONFIG_MACH_MP900C is not set
+# CONFIG_ARCH_PXA_IDP is not set
+# CONFIG_PXA_SHARPSL is not set
+# CONFIG_ARCH_VIPER is not set
+# CONFIG_ARCH_PXA_ESERIES is not set
+# CONFIG_TRIZEPS_PXA is not set
+# CONFIG_MACH_H5000 is not set
+# CONFIG_MACH_EM_X270 is not set
+# CONFIG_MACH_EXEDA is not set
+# CONFIG_MACH_COLIBRI is not set
+# CONFIG_MACH_COLIBRI300 is not set
+# CONFIG_MACH_COLIBRI320 is not set
+CONFIG_MACH_ZYLONITE=y
+CONFIG_MACH_LITTLETON=y
+CONFIG_MACH_TAVOREVB=y
+CONFIG_MACH_SAAR=y
+# CONFIG_MACH_ARMCORE is not set
+# CONFIG_MACH_CM_X300 is not set
+# CONFIG_MACH_H4700 is not set
+# CONFIG_MACH_MAGICIAN is not set
+# CONFIG_MACH_HIMALAYA is not set
+# CONFIG_MACH_MIOA701 is not set
+# CONFIG_MACH_PCM027 is not set
+# CONFIG_ARCH_PXA_PALM is not set
+# CONFIG_MACH_CSB726 is not set
+# CONFIG_PXA_EZX is not set
+CONFIG_PXA3xx=y
+CONFIG_PXA_SSP=y
+CONFIG_PXA_HAVE_BOARD_IRQS=y
+CONFIG_PLAT_PXA=y
+
+#
+# Processor Type
+#
+CONFIG_CPU_32=y
+CONFIG_CPU_XSC3=y
+CONFIG_CPU_32v5=y
+CONFIG_CPU_ABRT_EV5T=y
+CONFIG_CPU_PABRT_NOIFAR=y
+CONFIG_CPU_CACHE_VIVT=y
+CONFIG_CPU_TLB_V4WBI=y
+CONFIG_CPU_CP15=y
+CONFIG_CPU_CP15_MMU=y
+CONFIG_IO_36=y
+
+#
+# Processor Features
+#
+CONFIG_ARM_THUMB=y
+# CONFIG_CPU_DCACHE_DISABLE is not set
+# CONFIG_CPU_BPREDICT_DISABLE is not set
+CONFIG_OUTER_CACHE=y
+CONFIG_CACHE_XSC3L2=y
+CONFIG_IWMMXT=y
+CONFIG_COMMON_CLKDEV=y
+
+#
+# Bus support
+#
+# CONFIG_PCI_SYSCALL is not set
+# CONFIG_ARCH_SUPPORTS_MSI is not set
+# CONFIG_PCCARD is not set
+
+#
+# Kernel Features
+#
+CONFIG_TICK_ONESHOT=y
+# CONFIG_NO_HZ is not set
+# CONFIG_HIGH_RES_TIMERS is not set
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+CONFIG_VMSPLIT_3G=y
+# CONFIG_VMSPLIT_2G is not set
+# CONFIG_VMSPLIT_1G is not set
+CONFIG_PAGE_OFFSET=0xC0000000
+CONFIG_PREEMPT=y
+CONFIG_HZ=100
+CONFIG_AEABI=y
+CONFIG_OABI_COMPAT=y
+# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
+# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
+# CONFIG_HIGHMEM is not set
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+CONFIG_PAGEFLAGS_EXTENDED=y
+CONFIG_SPLIT_PTLOCK_CPUS=4096
+# CONFIG_PHYS_ADDR_T_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=0
+CONFIG_VIRT_TO_BUS=y
+CONFIG_HAVE_MLOCK=y
+CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
+CONFIG_ALIGNMENT_TRAP=y
+# CONFIG_UACCESS_WITH_MEMCPY is not set
+
+#
+# Boot options
+#
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_CMDLINE="root=/dev/nfs rootfstype=nfs nfsroot=192.168.1.100:/nfsroot/ ip=192.168.1.101:192.168.1.100::255.255.255.0::eth0:on console=ttyS0,115200 mem=64M debug"
+# CONFIG_XIP_KERNEL is not set
+# CONFIG_KEXEC is not set
+
+#
+# CPU Power Management
+#
+# CONFIG_CPU_FREQ is not set
+# CONFIG_CPU_IDLE is not set
+
+#
+# Floating point emulation
+#
+
+#
+# At least one emulation must be selected
+#
+CONFIG_FPE_NWFPE=y
+# CONFIG_FPE_NWFPE_XP is not set
+# CONFIG_FPE_FASTFPE is not set
+
+#
+# Userspace binary formats
+#
+CONFIG_BINFMT_ELF=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_HAVE_AOUT=y
+# CONFIG_BINFMT_AOUT is not set
+# CONFIG_BINFMT_MISC is not set
+
+#
+# Power management options
+#
+# CONFIG_PM is not set
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+# CONFIG_IP_MULTICAST is not set
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+# CONFIG_IP_PNP_DHCP is not set
+# CONFIG_IP_PNP_BOOTP is not set
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_ARPD is not set
+# CONFIG_SYN_COOKIES is not set
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+# CONFIG_INET_LRO is not set
+# CONFIG_INET_DIAG is not set
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_NETWORK_SECMARK is not set
+# CONFIG_NETFILTER is not set
+# CONFIG_IP_DCCP is not set
+# CONFIG_IP_SCTP is not set
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_NET_DSA is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+# CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
+# CONFIG_NET_SCHED is not set
+# CONFIG_DCB is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_CAN is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+# CONFIG_WIRELESS is not set
+# CONFIG_WIMAX is not set
+# CONFIG_RFKILL is not set
+# CONFIG_NET_9P is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_STANDALONE is not set
+# CONFIG_PREVENT_FIRMWARE_BUILD is not set
+CONFIG_FW_LOADER=y
+CONFIG_FIRMWARE_IN_KERNEL=y
+CONFIG_EXTRA_FIRMWARE=""
+# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
+# CONFIG_SYS_HYPERVISOR is not set
+# CONFIG_CONNECTOR is not set
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+CONFIG_MTD_CONCAT=y
+CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_TESTS is not set
+# CONFIG_MTD_REDBOOT_PARTS is not set
+# CONFIG_MTD_CMDLINE_PARTS is not set
+# CONFIG_MTD_AFS_PARTS is not set
+# CONFIG_MTD_AR7_PARTS is not set
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_BLOCK=y
+# CONFIG_FTL is not set
+# CONFIG_NFTL is not set
+# CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
+# CONFIG_SSFDC is not set
+# CONFIG_MTD_OOPS is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+# CONFIG_MTD_CFI is not set
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+# CONFIG_MTD_RAM is not set
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+
+#
+# Mapping drivers for chip access
+#
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_DATAFLASH is not set
+# CONFIG_MTD_M25P80 is not set
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_VERIFY_WRITE=y
+# CONFIG_MTD_NAND_ECC_SMC is not set
+# CONFIG_MTD_NAND_MUSEUM_IDS is not set
+# CONFIG_MTD_NAND_H1900 is not set
+# CONFIG_MTD_NAND_GPIO is not set
+CONFIG_MTD_NAND_IDS=y
+# CONFIG_MTD_NAND_DISKONCHIP is not set
+# CONFIG_MTD_NAND_SHARPSL is not set
+CONFIG_MTD_NAND_PXA3xx=y
+CONFIG_MTD_NAND_PXA3xx_BUILTIN=y
+# CONFIG_MTD_NAND_NANDSIM is not set
+# CONFIG_MTD_NAND_PLATFORM is not set
+CONFIG_MTD_ONENAND=y
+CONFIG_MTD_ONENAND_VERIFY_WRITE=y
+CONFIG_MTD_ONENAND_GENERIC=y
+# CONFIG_MTD_ONENAND_OTP is not set
+# CONFIG_MTD_ONENAND_2X_PROGRAM is not set
+# CONFIG_MTD_ONENAND_SIM is not set
+
+#
+# LPDDR flash memory drivers
+#
+# CONFIG_MTD_LPDDR is not set
+
+#
+# UBI - Unsorted block images
+#
+# CONFIG_MTD_UBI is not set
+# CONFIG_PARPORT is not set
+CONFIG_BLK_DEV=y
+# CONFIG_BLK_DEV_COW_COMMON is not set
+CONFIG_BLK_DEV_LOOP=y
+# CONFIG_BLK_DEV_CRYPTOLOOP is not set
+# CONFIG_BLK_DEV_NBD is not set
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=16
+CONFIG_BLK_DEV_RAM_SIZE=4096
+# CONFIG_BLK_DEV_XIP is not set
+# CONFIG_CDROM_PKTCDVD is not set
+# CONFIG_ATA_OVER_ETH is not set
+# CONFIG_MG_DISK is not set
+# CONFIG_MISC_DEVICES is not set
+CONFIG_HAVE_IDE=y
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+# CONFIG_SCSI is not set
+# CONFIG_SCSI_DMA is not set
+# CONFIG_SCSI_NETLINK is not set
+# CONFIG_ATA is not set
+# CONFIG_MD is not set
+CONFIG_NETDEVICES=y
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_MACVLAN is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+# CONFIG_VETH is not set
+# CONFIG_PHYLIB is not set
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=y
+# CONFIG_AX88796 is not set
+CONFIG_SMC91X=y
+# CONFIG_DM9000 is not set
+# CONFIG_ENC28J60 is not set
+# CONFIG_ETHOC is not set
+# CONFIG_SMC911X is not set
+# CONFIG_SMSC911X is not set
+# CONFIG_DNET is not set
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
+# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set
+# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
+# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
+# CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
+# CONFIG_NETDEV_1000 is not set
+# CONFIG_NETDEV_10000 is not set
+
+#
+# Wireless LAN
+#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
+
+#
+# Enable WiMAX (Networking options) to see the WiMAX drivers
+#
+# CONFIG_WAN is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+# CONFIG_ISDN is not set
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
+
+#
+# Userland interfaces
+#
+CONFIG_INPUT_MOUSEDEV=y
+# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
+CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
+CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
+# CONFIG_INPUT_JOYDEV is not set
+# CONFIG_INPUT_EVDEV is not set
+# CONFIG_INPUT_EVBUG is not set
+
+#
+# Input Device Drivers
+#
+CONFIG_INPUT_KEYBOARD=y
+# CONFIG_KEYBOARD_ATKBD is not set
+# CONFIG_KEYBOARD_SUNKBD is not set
+# CONFIG_KEYBOARD_LKKBD is not set
+# CONFIG_KEYBOARD_XTKBD is not set
+# CONFIG_KEYBOARD_NEWTON is not set
+# CONFIG_KEYBOARD_STOWAWAY is not set
+# CONFIG_KEYBOARD_LM8323 is not set
+CONFIG_KEYBOARD_PXA27x=y
+CONFIG_KEYBOARD_PXA930_ROTARY=y
+CONFIG_KEYBOARD_GPIO=y
+CONFIG_INPUT_MOUSE=y
+CONFIG_MOUSE_PS2=y
+CONFIG_MOUSE_PS2_ALPS=y
+CONFIG_MOUSE_PS2_LOGIPS2PP=y
+CONFIG_MOUSE_PS2_SYNAPTICS=y
+CONFIG_MOUSE_PS2_TRACKPOINT=y
+# CONFIG_MOUSE_PS2_ELANTECH is not set
+# CONFIG_MOUSE_PS2_TOUCHKIT is not set
+# CONFIG_MOUSE_SERIAL is not set
+# CONFIG_MOUSE_VSXXXAA is not set
+# CONFIG_MOUSE_GPIO is not set
+CONFIG_MOUSE_PXA930_TRKBALL=y
+# CONFIG_MOUSE_SYNAPTICS_I2C is not set
+# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
+CONFIG_INPUT_TOUCHSCREEN=y
+# CONFIG_TOUCHSCREEN_ADS7846 is not set
+# CONFIG_TOUCHSCREEN_AD7877 is not set
+# CONFIG_TOUCHSCREEN_AD7879_I2C is not set
+# CONFIG_TOUCHSCREEN_AD7879_SPI is not set
+# CONFIG_TOUCHSCREEN_AD7879 is not set
+CONFIG_TOUCHSCREEN_DA9034=y
+# CONFIG_TOUCHSCREEN_EETI is not set
+# CONFIG_TOUCHSCREEN_FUJITSU is not set
+# CONFIG_TOUCHSCREEN_GUNZE is not set
+# CONFIG_TOUCHSCREEN_ELO is not set
+# CONFIG_TOUCHSCREEN_WACOM_W8001 is not set
+# CONFIG_TOUCHSCREEN_MTOUCH is not set
+# CONFIG_TOUCHSCREEN_INEXIO is not set
+# CONFIG_TOUCHSCREEN_MK712 is not set
+# CONFIG_TOUCHSCREEN_PENMOUNT is not set
+# CONFIG_TOUCHSCREEN_TOUCHRIGHT is not set
+# CONFIG_TOUCHSCREEN_TOUCHWIN is not set
+# CONFIG_TOUCHSCREEN_TOUCHIT213 is not set
+# CONFIG_TOUCHSCREEN_TSC2007 is not set
+# CONFIG_TOUCHSCREEN_W90X900 is not set
+# CONFIG_INPUT_MISC is not set
+
+#
+# Hardware I/O ports
+#
+CONFIG_SERIO=y
+CONFIG_SERIO_SERPORT=y
+CONFIG_SERIO_LIBPS2=y
+# CONFIG_SERIO_RAW is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
+CONFIG_VT_CONSOLE=y
+CONFIG_HW_CONSOLE=y
+# CONFIG_VT_HW_CONSOLE_BINDING is not set
+CONFIG_DEVKMEM=y
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+# CONFIG_SERIAL_8250 is not set
+
+#
+# Non-8250 serial port support
+#
+# CONFIG_SERIAL_MAX3100 is not set
+CONFIG_SERIAL_PXA=y
+CONFIG_SERIAL_PXA_CONSOLE=y
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+CONFIG_UNIX98_PTYS=y
+# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set
+# CONFIG_LEGACY_PTYS is not set
+# CONFIG_IPMI_HANDLER is not set
+# CONFIG_HW_RANDOM is not set
+# CONFIG_R3964 is not set
+# CONFIG_RAW_DRIVER is not set
+# CONFIG_TCG_TPM is not set
+CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
+# CONFIG_I2C_CHARDEV is not set
+# CONFIG_I2C_HELPER_AUTO is not set
+
+#
+# I2C Algorithms
+#
+# CONFIG_I2C_ALGOBIT is not set
+# CONFIG_I2C_ALGOPCF is not set
+# CONFIG_I2C_ALGOPCA is not set
+
+#
+# I2C Hardware Bus support
+#
+
+#
+# I2C system bus drivers (mostly embedded / system-on-chip)
+#
+# CONFIG_I2C_DESIGNWARE is not set
+# CONFIG_I2C_GPIO is not set
+# CONFIG_I2C_OCORES is not set
+CONFIG_I2C_PXA=y
+# CONFIG_I2C_PXA_SLAVE is not set
+# CONFIG_I2C_SIMTEC is not set
+
+#
+# External I2C/SMBus adapter drivers
+#
+# CONFIG_I2C_PARPORT_LIGHT is not set
+# CONFIG_I2C_TAOS_EVM is not set
+
+#
+# Other I2C/SMBus bus drivers
+#
+# CONFIG_I2C_PCA_PLATFORM is not set
+# CONFIG_I2C_STUB is not set
+
+#
+# Miscellaneous I2C Chip support
+#
+# CONFIG_DS1682 is not set
+# CONFIG_SENSORS_TSL2550 is not set
+# CONFIG_I2C_DEBUG_CORE is not set
+# CONFIG_I2C_DEBUG_ALGO is not set
+# CONFIG_I2C_DEBUG_BUS is not set
+# CONFIG_I2C_DEBUG_CHIP is not set
+CONFIG_SPI=y
+# CONFIG_SPI_DEBUG is not set
+CONFIG_SPI_MASTER=y
+
+#
+# SPI Master Controller Drivers
+#
+# CONFIG_SPI_BITBANG is not set
+# CONFIG_SPI_GPIO is not set
+CONFIG_SPI_PXA2XX=y
+
+#
+# SPI Protocol Masters
+#
+# CONFIG_SPI_SPIDEV is not set
+# CONFIG_SPI_TLE62X0 is not set
+CONFIG_ARCH_REQUIRE_GPIOLIB=y
+CONFIG_GPIOLIB=y
+# CONFIG_DEBUG_GPIO is not set
+# CONFIG_GPIO_SYSFS is not set
+
+#
+# Memory mapped GPIO expanders:
+#
+
+#
+# I2C GPIO expanders:
+#
+CONFIG_GPIO_MAX732X=y
+CONFIG_GPIO_PCA953X=y
+CONFIG_GPIO_PCF857X=y
+
+#
+# PCI GPIO expanders:
+#
+
+#
+# SPI GPIO expanders:
+#
+CONFIG_GPIO_MAX7301=y
+# CONFIG_GPIO_MCP23S08 is not set
+# CONFIG_W1 is not set
+CONFIG_POWER_SUPPLY=y
+CONFIG_POWER_SUPPLY_DEBUG=y
+CONFIG_PDA_POWER=y
+# CONFIG_BATTERY_DS2760 is not set
+# CONFIG_BATTERY_BQ27x00 is not set
+CONFIG_BATTERY_DA9030=y
+# CONFIG_BATTERY_MAX17040 is not set
+# CONFIG_HWMON is not set
+# CONFIG_THERMAL is not set
+# CONFIG_THERMAL_HWMON is not set
+# CONFIG_WATCHDOG is not set
+CONFIG_SSB_POSSIBLE=y
+
+#
+# Sonics Silicon Backplane
+#
+# CONFIG_SSB is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_CORE is not set
+# CONFIG_MFD_SM501 is not set
+# CONFIG_MFD_ASIC3 is not set
+# CONFIG_HTC_EGPIO is not set
+# CONFIG_HTC_PASIC3 is not set
+# CONFIG_TPS65010 is not set
+# CONFIG_TWL4030_CORE is not set
+# CONFIG_MFD_TMIO is not set
+# CONFIG_MFD_T7L66XB is not set
+# CONFIG_MFD_TC6387XB is not set
+# CONFIG_MFD_TC6393XB is not set
+CONFIG_PMIC_DA903X=y
+# CONFIG_MFD_WM8400 is not set
+# CONFIG_MFD_WM8350_I2C is not set
+# CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
+# CONFIG_EZX_PCAP is not set
+# CONFIG_MEDIA_SUPPORT is not set
+
+#
+# Graphics support
+#
+# CONFIG_VGASTATE is not set
+# CONFIG_VIDEO_OUTPUT_CONTROL is not set
+CONFIG_FB=y
+# CONFIG_FIRMWARE_EDID is not set
+# CONFIG_FB_DDC is not set
+# CONFIG_FB_BOOT_VESA_SUPPORT is not set
+CONFIG_FB_CFB_FILLRECT=y
+CONFIG_FB_CFB_COPYAREA=y
+CONFIG_FB_CFB_IMAGEBLIT=y
+# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
+# CONFIG_FB_SYS_FILLRECT is not set
+# CONFIG_FB_SYS_COPYAREA is not set
+# CONFIG_FB_SYS_IMAGEBLIT is not set
+# CONFIG_FB_FOREIGN_ENDIAN is not set
+# CONFIG_FB_SYS_FOPS is not set
+# CONFIG_FB_SVGALIB is not set
+# CONFIG_FB_MACMODES is not set
+# CONFIG_FB_BACKLIGHT is not set
+# CONFIG_FB_MODE_HELPERS is not set
+# CONFIG_FB_TILEBLITTING is not set
+
+#
+# Frame buffer hardware drivers
+#
+# CONFIG_FB_S1D13XXX is not set
+CONFIG_FB_PXA=y
+# CONFIG_FB_PXA_OVERLAY is not set
+# CONFIG_FB_PXA_SMARTPANEL is not set
+# CONFIG_FB_PXA_PARAMETERS is not set
+# CONFIG_FB_MBX is not set
+# CONFIG_FB_W100 is not set
+# CONFIG_FB_VIRTUAL is not set
+# CONFIG_FB_METRONOME is not set
+# CONFIG_FB_MB862XX is not set
+# CONFIG_FB_BROADSHEET is not set
+CONFIG_BACKLIGHT_LCD_SUPPORT=y
+CONFIG_LCD_CLASS_DEVICE=y
+# CONFIG_LCD_LTV350QV is not set
+# CONFIG_LCD_ILI9320 is not set
+CONFIG_LCD_TDO24M=y
+# CONFIG_LCD_VGG2432A4 is not set
+# CONFIG_LCD_PLATFORM is not set
+CONFIG_BACKLIGHT_CLASS_DEVICE=y
+# CONFIG_BACKLIGHT_GENERIC is not set
+CONFIG_BACKLIGHT_PWM=y
+CONFIG_BACKLIGHT_DA903X=y
+
+#
+# Display device support
+#
+# CONFIG_DISPLAY_SUPPORT is not set
+
+#
+# Console display driver support
+#
+# CONFIG_VGA_CONSOLE is not set
+CONFIG_DUMMY_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
+# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
+CONFIG_FONTS=y
+# CONFIG_FONT_8x8 is not set
+# CONFIG_FONT_8x16 is not set
+CONFIG_FONT_6x11=y
+# CONFIG_FONT_7x14 is not set
+# CONFIG_FONT_PEARL_8x8 is not set
+# CONFIG_FONT_ACORN_8x8 is not set
+# CONFIG_FONT_MINI_4x6 is not set
+# CONFIG_FONT_SUN8x16 is not set
+# CONFIG_FONT_SUN12x22 is not set
+# CONFIG_FONT_10x18 is not set
+CONFIG_LOGO=y
+CONFIG_LOGO_LINUX_MONO=y
+CONFIG_LOGO_LINUX_VGA16=y
+CONFIG_LOGO_LINUX_CLUT224=y
+# CONFIG_SOUND is not set
+# CONFIG_HID_SUPPORT is not set
+# CONFIG_USB_SUPPORT is not set
+CONFIG_MMC=y
+# CONFIG_MMC_DEBUG is not set
+# CONFIG_MMC_UNSAFE_RESUME is not set
+
+#
+# MMC/SD/SDIO Card Drivers
+#
+CONFIG_MMC_BLOCK=y
+CONFIG_MMC_BLOCK_BOUNCE=y
+# CONFIG_SDIO_UART is not set
+# CONFIG_MMC_TEST is not set
+
+#
+# MMC/SD/SDIO Host Controller Drivers
+#
+CONFIG_MMC_PXA=y
+# CONFIG_MMC_SDHCI is not set
+# CONFIG_MMC_SPI is not set
+# CONFIG_MEMSTICK is not set
+# CONFIG_ACCESSIBILITY is not set
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=m
+
+#
+# LED drivers
+#
+# CONFIG_LEDS_PCA9532 is not set
+CONFIG_LEDS_GPIO=m
+CONFIG_LEDS_GPIO_PLATFORM=y
+# CONFIG_LEDS_LP5521 is not set
+# CONFIG_LEDS_PCA955X is not set
+CONFIG_LEDS_DA903X=m
+# CONFIG_LEDS_DAC124S085 is not set
+# CONFIG_LEDS_PWM is not set
+# CONFIG_LEDS_BD2802 is not set
+
+#
+# LED Triggers
+#
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_TIMER=m
+CONFIG_LEDS_TRIGGER_HEARTBEAT=m
+CONFIG_LEDS_TRIGGER_BACKLIGHT=m
+CONFIG_LEDS_TRIGGER_GPIO=m
+CONFIG_LEDS_TRIGGER_DEFAULT_ON=m
+
+#
+# iptables trigger is under Netfilter config (LED target)
+#
+CONFIG_RTC_LIB=y
+# CONFIG_RTC_CLASS is not set
+# CONFIG_DMADEVICES is not set
+# CONFIG_AUXDISPLAY is not set
+CONFIG_REGULATOR=y
+CONFIG_REGULATOR_DEBUG=y
+# CONFIG_REGULATOR_FIXED_VOLTAGE is not set
+CONFIG_REGULATOR_VIRTUAL_CONSUMER=y
+# CONFIG_REGULATOR_USERSPACE_CONSUMER is not set
+# CONFIG_REGULATOR_BQ24022 is not set
+# CONFIG_REGULATOR_MAX1586 is not set
+CONFIG_REGULATOR_DA903X=y
+# CONFIG_REGULATOR_LP3971 is not set
+# CONFIG_UIO is not set
+# CONFIG_STAGING is not set
+
+#
+# File systems
+#
+# CONFIG_EXT2_FS is not set
+# CONFIG_EXT3_FS is not set
+# CONFIG_EXT4_FS is not set
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+CONFIG_FS_POSIX_ACL=y
+# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
+# CONFIG_OCFS2_FS is not set
+# CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
+CONFIG_DNOTIFY=y
+# CONFIG_INOTIFY is not set
+CONFIG_INOTIFY_USER=y
+# CONFIG_QUOTA is not set
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# Caches
+#
+# CONFIG_FSCACHE is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+# CONFIG_MSDOS_FS is not set
+# CONFIG_VFAT_FS is not set
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_SYSCTL=y
+CONFIG_PROC_PAGE_MONITOR=y
+CONFIG_SYSFS=y
+# CONFIG_TMPFS is not set
+# CONFIG_HUGETLB_PAGE is not set
+# CONFIG_CONFIGFS_FS is not set
+CONFIG_MISC_FILESYSTEMS=y
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_FS_DEBUG=0
+CONFIG_JFFS2_FS_WRITEBUFFER=y
+CONFIG_JFFS2_FS_WBUF_VERIFY=y
+# CONFIG_JFFS2_SUMMARY is not set
+# CONFIG_JFFS2_FS_XATTR is not set
+CONFIG_JFFS2_COMPRESSION_OPTIONS=y
+CONFIG_JFFS2_ZLIB=y
+CONFIG_JFFS2_LZO=y
+CONFIG_JFFS2_RTIME=y
+CONFIG_JFFS2_RUBIN=y
+# CONFIG_JFFS2_CMODE_NONE is not set
+CONFIG_JFFS2_CMODE_PRIORITY=y
+# CONFIG_JFFS2_CMODE_SIZE is not set
+# CONFIG_JFFS2_CMODE_FAVOURLZO is not set
+# CONFIG_CRAMFS is not set
+# CONFIG_SQUASHFS is not set
+# CONFIG_VXFS_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_OMFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_ROMFS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+# CONFIG_NILFS2_FS is not set
+CONFIG_NETWORK_FILESYSTEMS=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+CONFIG_NFS_V3_ACL=y
+CONFIG_NFS_V4=y
+# CONFIG_NFS_V4_1 is not set
+CONFIG_ROOT_NFS=y
+# CONFIG_NFSD is not set
+CONFIG_LOCKD=y
+CONFIG_LOCKD_V4=y
+CONFIG_NFS_ACL_SUPPORT=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+CONFIG_SUNRPC_GSS=y
+CONFIG_RPCSEC_GSS_KRB5=y
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+
+#
+# Partition Types
+#
+# CONFIG_PARTITION_ADVANCED is not set
+CONFIG_MSDOS_PARTITION=y
+CONFIG_NLS=y
+CONFIG_NLS_DEFAULT="iso8859-1"
+# CONFIG_NLS_CODEPAGE_437 is not set
+# CONFIG_NLS_CODEPAGE_737 is not set
+# CONFIG_NLS_CODEPAGE_775 is not set
+# CONFIG_NLS_CODEPAGE_850 is not set
+# CONFIG_NLS_CODEPAGE_852 is not set
+# CONFIG_NLS_CODEPAGE_855 is not set
+# CONFIG_NLS_CODEPAGE_857 is not set
+# CONFIG_NLS_CODEPAGE_860 is not set
+# CONFIG_NLS_CODEPAGE_861 is not set
+# CONFIG_NLS_CODEPAGE_862 is not set
+# CONFIG_NLS_CODEPAGE_863 is not set
+# CONFIG_NLS_CODEPAGE_864 is not set
+# CONFIG_NLS_CODEPAGE_865 is not set
+# CONFIG_NLS_CODEPAGE_866 is not set
+# CONFIG_NLS_CODEPAGE_869 is not set
+# CONFIG_NLS_CODEPAGE_936 is not set
+# CONFIG_NLS_CODEPAGE_950 is not set
+# CONFIG_NLS_CODEPAGE_932 is not set
+# CONFIG_NLS_CODEPAGE_949 is not set
+# CONFIG_NLS_CODEPAGE_874 is not set
+# CONFIG_NLS_ISO8859_8 is not set
+# CONFIG_NLS_CODEPAGE_1250 is not set
+# CONFIG_NLS_CODEPAGE_1251 is not set
+# CONFIG_NLS_ASCII is not set
+# CONFIG_NLS_ISO8859_1 is not set
+# CONFIG_NLS_ISO8859_2 is not set
+# CONFIG_NLS_ISO8859_3 is not set
+# CONFIG_NLS_ISO8859_4 is not set
+# CONFIG_NLS_ISO8859_5 is not set
+# CONFIG_NLS_ISO8859_6 is not set
+# CONFIG_NLS_ISO8859_7 is not set
+# CONFIG_NLS_ISO8859_9 is not set
+# CONFIG_NLS_ISO8859_13 is not set
+# CONFIG_NLS_ISO8859_14 is not set
+# CONFIG_NLS_ISO8859_15 is not set
+# CONFIG_NLS_KOI8_R is not set
+# CONFIG_NLS_KOI8_U is not set
+# CONFIG_NLS_UTF8 is not set
+# CONFIG_DLM is not set
+
+#
+# Kernel hacking
+#
+CONFIG_PRINTK_TIME=y
+CONFIG_ENABLE_WARN_DEPRECATED=y
+CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_FRAME_WARN=1024
+CONFIG_MAGIC_SYSRQ=y
+# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
+CONFIG_DEBUG_KERNEL=y
+CONFIG_DEBUG_SHIRQ=y
+CONFIG_DETECT_SOFTLOCKUP=y
+CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC=y
+CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=1
+CONFIG_DETECT_HUNG_TASK=y
+# CONFIG_BOOTPARAM_HUNG_TASK_PANIC is not set
+CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=0
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
+# CONFIG_DEBUG_OBJECTS is not set
+# CONFIG_DEBUG_SLAB is not set
+# CONFIG_DEBUG_KMEMLEAK is not set
+CONFIG_DEBUG_PREEMPT=y
+# CONFIG_DEBUG_RT_MUTEXES is not set
+# CONFIG_RT_MUTEX_TESTER is not set
+CONFIG_DEBUG_SPINLOCK=y
+# CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_LOCK_ALLOC is not set
+# CONFIG_PROVE_LOCKING is not set
+# CONFIG_LOCK_STAT is not set
+CONFIG_DEBUG_SPINLOCK_SLEEP=y
+# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+# CONFIG_DEBUG_KOBJECT is not set
+CONFIG_DEBUG_BUGVERBOSE=y
+# CONFIG_DEBUG_INFO is not set
+# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_WRITECOUNT is not set
+CONFIG_DEBUG_MEMORY_INIT=y
+# CONFIG_DEBUG_LIST is not set
+# CONFIG_DEBUG_SG is not set
+# CONFIG_DEBUG_NOTIFIERS is not set
+# CONFIG_BOOT_PRINTK_DELAY is not set
+# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_RCU_CPU_STALL_DETECTOR is not set
+# CONFIG_BACKTRACE_SELF_TEST is not set
+# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
+# CONFIG_FAULT_INJECTION is not set
+# CONFIG_LATENCYTOP is not set
+# CONFIG_SYSCTL_SYSCALL_CHECK is not set
+# CONFIG_PAGE_POISONING is not set
+CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_TRACING_SUPPORT=y
+# CONFIG_FTRACE is not set
+# CONFIG_SAMPLES is not set
+CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_KGDB is not set
+# CONFIG_KMEMCHECK is not set
+CONFIG_ARM_UNWIND=y
+CONFIG_DEBUG_USER=y
+# CONFIG_DEBUG_ERRORS is not set
+# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_DEBUG_LL is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+# CONFIG_SECURITYFS is not set
+# CONFIG_SECURITY_FILE_CAPABILITIES is not set
+CONFIG_CRYPTO=y
+
+#
+# Crypto core or helper
+#
+# CONFIG_CRYPTO_FIPS is not set
+CONFIG_CRYPTO_ALGAPI=y
+CONFIG_CRYPTO_ALGAPI2=y
+CONFIG_CRYPTO_AEAD2=y
+CONFIG_CRYPTO_BLKCIPHER=y
+CONFIG_CRYPTO_BLKCIPHER2=y
+CONFIG_CRYPTO_HASH=y
+CONFIG_CRYPTO_HASH2=y
+CONFIG_CRYPTO_RNG2=y
+CONFIG_CRYPTO_PCOMP=y
+CONFIG_CRYPTO_MANAGER=y
+CONFIG_CRYPTO_MANAGER2=y
+# CONFIG_CRYPTO_GF128MUL is not set
+# CONFIG_CRYPTO_NULL is not set
+CONFIG_CRYPTO_WORKQUEUE=y
+# CONFIG_CRYPTO_CRYPTD is not set
+# CONFIG_CRYPTO_AUTHENC is not set
+# CONFIG_CRYPTO_TEST is not set
+
+#
+# Authenticated Encryption with Associated Data
+#
+# CONFIG_CRYPTO_CCM is not set
+# CONFIG_CRYPTO_GCM is not set
+# CONFIG_CRYPTO_SEQIV is not set
+
+#
+# Block modes
+#
+CONFIG_CRYPTO_CBC=y
+# CONFIG_CRYPTO_CTR is not set
+# CONFIG_CRYPTO_CTS is not set
+# CONFIG_CRYPTO_ECB is not set
+# CONFIG_CRYPTO_LRW is not set
+# CONFIG_CRYPTO_PCBC is not set
+# CONFIG_CRYPTO_XTS is not set
+
+#
+# Hash modes
+#
+# CONFIG_CRYPTO_HMAC is not set
+# CONFIG_CRYPTO_XCBC is not set
+
+#
+# Digest
+#
+# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_MD4 is not set
+CONFIG_CRYPTO_MD5=y
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_RMD128 is not set
+# CONFIG_CRYPTO_RMD160 is not set
+# CONFIG_CRYPTO_RMD256 is not set
+# CONFIG_CRYPTO_RMD320 is not set
+# CONFIG_CRYPTO_SHA1 is not set
+# CONFIG_CRYPTO_SHA256 is not set
+# CONFIG_CRYPTO_SHA512 is not set
+# CONFIG_CRYPTO_TGR192 is not set
+# CONFIG_CRYPTO_WP512 is not set
+
+#
+# Ciphers
+#
+# CONFIG_CRYPTO_AES is not set
+# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_CAMELLIA is not set
+# CONFIG_CRYPTO_CAST5 is not set
+# CONFIG_CRYPTO_CAST6 is not set
+CONFIG_CRYPTO_DES=y
+# CONFIG_CRYPTO_FCRYPT is not set
+# CONFIG_CRYPTO_KHAZAD is not set
+# CONFIG_CRYPTO_SALSA20 is not set
+# CONFIG_CRYPTO_SEED is not set
+# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_TWOFISH is not set
+
+#
+# Compression
+#
+# CONFIG_CRYPTO_DEFLATE is not set
+# CONFIG_CRYPTO_ZLIB is not set
+# CONFIG_CRYPTO_LZO is not set
+
+#
+# Random Number Generation
+#
+# CONFIG_CRYPTO_ANSI_CPRNG is not set
+# CONFIG_CRYPTO_HW is not set
+# CONFIG_BINARY_PRINTF is not set
+
+#
+# Library routines
+#
+CONFIG_BITREVERSE=y
+CONFIG_GENERIC_FIND_LAST_BIT=y
+# CONFIG_CRC_CCITT is not set
+# CONFIG_CRC16 is not set
+# CONFIG_CRC_T10DIF is not set
+# CONFIG_CRC_ITU_T is not set
+CONFIG_CRC32=y
+# CONFIG_CRC7 is not set
+# CONFIG_LIBCRC32C is not set
+CONFIG_ZLIB_INFLATE=y
+CONFIG_ZLIB_DEFLATE=y
+CONFIG_LZO_COMPRESS=y
+CONFIG_LZO_DECOMPRESS=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
+CONFIG_NLATTR=y
--- /dev/null
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.31-rc6
+# Thu Aug 20 09:02:37 2009
+#
+CONFIG_ARM=y
+CONFIG_SYS_SUPPORTS_APM_EMULATION=y
+CONFIG_GENERIC_GPIO=y
+CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_MMU=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_STACKTRACE_SUPPORT=y
+CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_LOCKDEP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
+CONFIG_HARDIRQS_SW_RESEND=y
+CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_RWSEM_GENERIC_SPINLOCK=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_ARCH_MTD_XIP=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
+CONFIG_VECTORS_BASE=0xffff0000
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
+
+#
+# General setup
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_LOCALVERSION=".xcep-itech"
+# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_SYSVIPC=y
+CONFIG_SYSVIPC_SYSCTL=y
+# CONFIG_POSIX_MQUEUE is not set
+CONFIG_BSD_PROCESS_ACCT=y
+# CONFIG_BSD_PROCESS_ACCT_V3 is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_AUDIT is not set
+
+#
+# RCU Subsystem
+#
+CONFIG_CLASSIC_RCU=y
+# CONFIG_TREE_RCU is not set
+# CONFIG_PREEMPT_RCU is not set
+# CONFIG_TREE_RCU_TRACE is not set
+# CONFIG_PREEMPT_RCU_TRACE is not set
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=16
+# CONFIG_GROUP_SCHED is not set
+# CONFIG_CGROUPS is not set
+CONFIG_SYSFS_DEPRECATED=y
+CONFIG_SYSFS_DEPRECATED_V2=y
+# CONFIG_RELAY is not set
+# CONFIG_NAMESPACES is not set
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_INITRAMFS_SOURCE=""
+CONFIG_RD_GZIP=y
+# CONFIG_RD_BZIP2 is not set
+# CONFIG_RD_LZMA is not set
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_SYSCTL=y
+CONFIG_ANON_INODES=y
+CONFIG_EMBEDDED=y
+# CONFIG_UID16 is not set
+CONFIG_SYSCTL_SYSCALL=y
+CONFIG_KALLSYMS=y
+# CONFIG_KALLSYMS_ALL is not set
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
+# CONFIG_SHMEM is not set
+CONFIG_AIO=y
+
+#
+# Performance Counters
+#
+# CONFIG_VM_EVENT_COUNTERS is not set
+CONFIG_STRIP_ASM_SYMS=y
+# CONFIG_COMPAT_BRK is not set
+# CONFIG_SLAB is not set
+# CONFIG_SLUB is not set
+CONFIG_SLOB=y
+# CONFIG_PROFILING is not set
+CONFIG_TRACEPOINTS=y
+CONFIG_MARKERS=y
+CONFIG_HAVE_OPROFILE=y
+CONFIG_KPROBES=y
+CONFIG_KRETPROBES=y
+CONFIG_HAVE_KPROBES=y
+CONFIG_HAVE_KRETPROBES=y
+CONFIG_HAVE_CLK=y
+
+#
+# GCOV-based kernel profiling
+#
+# CONFIG_SLOW_WORK is not set
+CONFIG_HAVE_GENERIC_DMA_COHERENT=y
+CONFIG_RT_MUTEXES=y
+CONFIG_BASE_SMALL=0
+CONFIG_MODULES=y
+# CONFIG_MODULE_FORCE_LOAD is not set
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_MODULE_FORCE_UNLOAD is not set
+CONFIG_MODVERSIONS=y
+CONFIG_MODULE_SRCVERSION_ALL=y
+# CONFIG_BLOCK is not set
+# CONFIG_FREEZER is not set
+
+#
+# System Type
+#
+# CONFIG_ARCH_AAEC2000 is not set
+# CONFIG_ARCH_INTEGRATOR is not set
+# CONFIG_ARCH_REALVIEW is not set
+# CONFIG_ARCH_VERSATILE is not set
+# CONFIG_ARCH_AT91 is not set
+# CONFIG_ARCH_CLPS711X is not set
+# CONFIG_ARCH_GEMINI is not set
+# CONFIG_ARCH_EBSA110 is not set
+# CONFIG_ARCH_EP93XX is not set
+# CONFIG_ARCH_FOOTBRIDGE is not set
+# CONFIG_ARCH_MXC is not set
+# CONFIG_ARCH_STMP3XXX is not set
+# CONFIG_ARCH_NETX is not set
+# CONFIG_ARCH_H720X is not set
+# CONFIG_ARCH_IOP13XX is not set
+# CONFIG_ARCH_IOP32X is not set
+# CONFIG_ARCH_IOP33X is not set
+# CONFIG_ARCH_IXP23XX is not set
+# CONFIG_ARCH_IXP2000 is not set
+# CONFIG_ARCH_IXP4XX is not set
+# CONFIG_ARCH_L7200 is not set
+# CONFIG_ARCH_KIRKWOOD is not set
+# CONFIG_ARCH_LOKI is not set
+# CONFIG_ARCH_MV78XX0 is not set
+# CONFIG_ARCH_ORION5X is not set
+# CONFIG_ARCH_MMP is not set
+# CONFIG_ARCH_KS8695 is not set
+# CONFIG_ARCH_NS9XXX is not set
+# CONFIG_ARCH_W90X900 is not set
+# CONFIG_ARCH_PNX4008 is not set
+CONFIG_ARCH_PXA=y
+# CONFIG_ARCH_MSM is not set
+# CONFIG_ARCH_RPC is not set
+# CONFIG_ARCH_SA1100 is not set
+# CONFIG_ARCH_S3C2410 is not set
+# CONFIG_ARCH_S3C64XX is not set
+# CONFIG_ARCH_SHARK is not set
+# CONFIG_ARCH_LH7A40X is not set
+# CONFIG_ARCH_U300 is not set
+# CONFIG_ARCH_DAVINCI is not set
+# CONFIG_ARCH_OMAP is not set
+
+#
+# Intel PXA2xx/PXA3xx Implementations
+#
+# CONFIG_ARCH_GUMSTIX is not set
+# CONFIG_MACH_INTELMOTE2 is not set
+# CONFIG_MACH_STARGATE2 is not set
+# CONFIG_ARCH_LUBBOCK is not set
+# CONFIG_MACH_LOGICPD_PXA270 is not set
+# CONFIG_MACH_MAINSTONE is not set
+# CONFIG_MACH_MP900C is not set
+# CONFIG_ARCH_PXA_IDP is not set
+# CONFIG_PXA_SHARPSL is not set
+# CONFIG_ARCH_VIPER is not set
+# CONFIG_ARCH_PXA_ESERIES is not set
+# CONFIG_TRIZEPS_PXA is not set
+# CONFIG_MACH_H5000 is not set
+# CONFIG_MACH_EM_X270 is not set
+# CONFIG_MACH_EXEDA is not set
+# CONFIG_MACH_COLIBRI is not set
+# CONFIG_MACH_COLIBRI300 is not set
+# CONFIG_MACH_COLIBRI320 is not set
+# CONFIG_MACH_ZYLONITE is not set
+# CONFIG_MACH_LITTLETON is not set
+# CONFIG_MACH_TAVOREVB is not set
+# CONFIG_MACH_SAAR is not set
+# CONFIG_MACH_ARMCORE is not set
+# CONFIG_MACH_CM_X300 is not set
+# CONFIG_MACH_H4700 is not set
+# CONFIG_MACH_MAGICIAN is not set
+# CONFIG_MACH_HIMALAYA is not set
+# CONFIG_MACH_MIOA701 is not set
+# CONFIG_MACH_PCM027 is not set
+# CONFIG_ARCH_PXA_PALM is not set
+# CONFIG_MACH_CSB726 is not set
+# CONFIG_PXA_EZX is not set
+CONFIG_MACH_XCEP=y
+CONFIG_PXA25x=y
+CONFIG_PXA_SSP=y
+CONFIG_PLAT_PXA=y
+
+#
+# Processor Type
+#
+CONFIG_CPU_32=y
+CONFIG_CPU_XSCALE=y
+CONFIG_CPU_32v5=y
+CONFIG_CPU_ABRT_EV5T=y
+CONFIG_CPU_PABRT_NOIFAR=y
+CONFIG_CPU_CACHE_VIVT=y
+CONFIG_CPU_TLB_V4WBI=y
+CONFIG_CPU_CP15=y
+CONFIG_CPU_CP15_MMU=y
+
+#
+# Processor Features
+#
+CONFIG_ARM_THUMB=y
+# CONFIG_CPU_DCACHE_DISABLE is not set
+CONFIG_IWMMXT=y
+CONFIG_XSCALE_PMU=y
+CONFIG_COMMON_CLKDEV=y
+
+#
+# Bus support
+#
+# CONFIG_PCI_SYSCALL is not set
+# CONFIG_ARCH_SUPPORTS_MSI is not set
+# CONFIG_PCCARD is not set
+
+#
+# Kernel Features
+#
+CONFIG_TICK_ONESHOT=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+CONFIG_VMSPLIT_3G=y
+# CONFIG_VMSPLIT_2G is not set
+# CONFIG_VMSPLIT_1G is not set
+CONFIG_PAGE_OFFSET=0xC0000000
+# CONFIG_PREEMPT is not set
+CONFIG_HZ=100
+CONFIG_AEABI=y
+CONFIG_OABI_COMPAT=y
+# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
+# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
+# CONFIG_HIGHMEM is not set
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+CONFIG_PAGEFLAGS_EXTENDED=y
+CONFIG_SPLIT_PTLOCK_CPUS=4096
+# CONFIG_PHYS_ADDR_T_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=0
+CONFIG_VIRT_TO_BUS=y
+CONFIG_HAVE_MLOCK=y
+CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
+CONFIG_ALIGNMENT_TRAP=y
+# CONFIG_UACCESS_WITH_MEMCPY is not set
+
+#
+# Boot options
+#
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_CMDLINE="root=mtd4 rootfstype=jffs2 ro console=ttyS0,115200"
+# CONFIG_XIP_KERNEL is not set
+# CONFIG_KEXEC is not set
+
+#
+# CPU Power Management
+#
+# CONFIG_CPU_FREQ is not set
+# CONFIG_CPU_IDLE is not set
+
+#
+# Floating point emulation
+#
+
+#
+# At least one emulation must be selected
+#
+CONFIG_FPE_NWFPE=y
+# CONFIG_FPE_NWFPE_XP is not set
+# CONFIG_FPE_FASTFPE is not set
+
+#
+# Userspace binary formats
+#
+CONFIG_BINFMT_ELF=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_HAVE_AOUT=y
+# CONFIG_BINFMT_AOUT is not set
+# CONFIG_BINFMT_MISC is not set
+
+#
+# Power management options
+#
+# CONFIG_PM is not set
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=m
+CONFIG_PACKET_MMAP=y
+CONFIG_UNIX=y
+CONFIG_XFRM=y
+# CONFIG_XFRM_USER is not set
+# CONFIG_XFRM_SUB_POLICY is not set
+# CONFIG_XFRM_MIGRATE is not set
+# CONFIG_XFRM_STATISTICS is not set
+CONFIG_NET_KEY=y
+# CONFIG_NET_KEY_MIGRATE is not set
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_IP_MROUTE is not set
+# CONFIG_ARPD is not set
+# CONFIG_SYN_COOKIES is not set
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+CONFIG_INET_LRO=y
+# CONFIG_INET_DIAG is not set
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_NETWORK_SECMARK is not set
+# CONFIG_NETFILTER is not set
+# CONFIG_IP_DCCP is not set
+# CONFIG_IP_SCTP is not set
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_NET_DSA is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+# CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
+# CONFIG_NET_SCHED is not set
+# CONFIG_DCB is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_NET_TCPPROBE is not set
+# CONFIG_NET_DROP_MONITOR is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_CAN is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+# CONFIG_WIRELESS is not set
+# CONFIG_WIMAX is not set
+# CONFIG_RFKILL is not set
+# CONFIG_NET_9P is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_STANDALONE=y
+# CONFIG_PREVENT_FIRMWARE_BUILD is not set
+# CONFIG_FW_LOADER is not set
+# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
+# CONFIG_SYS_HYPERVISOR is not set
+# CONFIG_CONNECTOR is not set
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+CONFIG_MTD_CONCAT=y
+CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_TESTS is not set
+# CONFIG_MTD_REDBOOT_PARTS is not set
+# CONFIG_MTD_CMDLINE_PARTS is not set
+# CONFIG_MTD_AFS_PARTS is not set
+# CONFIG_MTD_AR7_PARTS is not set
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+# CONFIG_MTD_OOPS is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+CONFIG_MTD_CFI=y
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_GEN_PROBE=y
+# CONFIG_MTD_CFI_ADV_OPTIONS is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+CONFIG_MTD_CFI_INTELEXT=y
+# CONFIG_MTD_CFI_AMDSTD is not set
+# CONFIG_MTD_CFI_STAA is not set
+CONFIG_MTD_CFI_UTIL=y
+# CONFIG_MTD_RAM is not set
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+# CONFIG_MTD_XIP is not set
+
+#
+# Mapping drivers for chip access
+#
+CONFIG_MTD_COMPLEX_MAPPINGS=y
+CONFIG_MTD_PHYSMAP=y
+# CONFIG_MTD_PHYSMAP_COMPAT is not set
+CONFIG_MTD_PXA2XX=y
+# CONFIG_MTD_ARM_INTEGRATOR is not set
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+# CONFIG_MTD_NAND is not set
+# CONFIG_MTD_ONENAND is not set
+
+#
+# LPDDR flash memory drivers
+#
+# CONFIG_MTD_LPDDR is not set
+
+#
+# UBI - Unsorted block images
+#
+# CONFIG_MTD_UBI is not set
+# CONFIG_PARPORT is not set
+# CONFIG_MISC_DEVICES is not set
+CONFIG_HAVE_IDE=y
+
+#
+# SCSI device support
+#
+# CONFIG_SCSI_DMA is not set
+# CONFIG_SCSI_NETLINK is not set
+CONFIG_NETDEVICES=y
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_MACVLAN is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+# CONFIG_VETH is not set
+# CONFIG_PHYLIB is not set
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=y
+# CONFIG_AX88796 is not set
+CONFIG_SMC91X=y
+# CONFIG_DM9000 is not set
+# CONFIG_ETHOC is not set
+# CONFIG_SMC911X is not set
+# CONFIG_SMSC911X is not set
+# CONFIG_DNET is not set
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
+# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set
+# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
+# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
+# CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
+# CONFIG_NETDEV_1000 is not set
+# CONFIG_NETDEV_10000 is not set
+
+#
+# Wireless LAN
+#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
+
+#
+# Enable WiMAX (Networking options) to see the WiMAX drivers
+#
+# CONFIG_WAN is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+# CONFIG_ISDN is not set
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
+
+#
+# Userland interfaces
+#
+# CONFIG_INPUT_MOUSEDEV is not set
+# CONFIG_INPUT_JOYDEV is not set
+# CONFIG_INPUT_EVDEV is not set
+# CONFIG_INPUT_EVBUG is not set
+
+#
+# Input Device Drivers
+#
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
+# CONFIG_INPUT_TOUCHSCREEN is not set
+# CONFIG_INPUT_MISC is not set
+
+#
+# Hardware I/O ports
+#
+# CONFIG_SERIO is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
+CONFIG_VT_CONSOLE=y
+CONFIG_HW_CONSOLE=y
+# CONFIG_VT_HW_CONSOLE_BINDING is not set
+# CONFIG_DEVKMEM is not set
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+# CONFIG_SERIAL_8250 is not set
+
+#
+# Non-8250 serial port support
+#
+CONFIG_SERIAL_PXA=y
+CONFIG_SERIAL_PXA_CONSOLE=y
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+CONFIG_UNIX98_PTYS=y
+# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set
+# CONFIG_LEGACY_PTYS is not set
+# CONFIG_IPMI_HANDLER is not set
+# CONFIG_HW_RANDOM is not set
+# CONFIG_R3964 is not set
+# CONFIG_TCG_TPM is not set
+CONFIG_I2C=m
+CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_CHARDEV=m
+CONFIG_I2C_HELPER_AUTO=y
+
+#
+# I2C Hardware Bus support
+#
+
+#
+# I2C system bus drivers (mostly embedded / system-on-chip)
+#
+# CONFIG_I2C_DESIGNWARE is not set
+# CONFIG_I2C_GPIO is not set
+# CONFIG_I2C_OCORES is not set
+CONFIG_I2C_PXA=m
+# CONFIG_I2C_PXA_SLAVE is not set
+# CONFIG_I2C_SIMTEC is not set
+
+#
+# External I2C/SMBus adapter drivers
+#
+# CONFIG_I2C_PARPORT_LIGHT is not set
+# CONFIG_I2C_TAOS_EVM is not set
+
+#
+# Other I2C/SMBus bus drivers
+#
+# CONFIG_I2C_PCA_PLATFORM is not set
+# CONFIG_I2C_STUB is not set
+
+#
+# Miscellaneous I2C Chip support
+#
+# CONFIG_DS1682 is not set
+# CONFIG_SENSORS_PCF8574 is not set
+# CONFIG_PCF8575 is not set
+# CONFIG_SENSORS_PCA9539 is not set
+# CONFIG_SENSORS_TSL2550 is not set
+# CONFIG_I2C_DEBUG_CORE is not set
+# CONFIG_I2C_DEBUG_ALGO is not set
+# CONFIG_I2C_DEBUG_BUS is not set
+# CONFIG_I2C_DEBUG_CHIP is not set
+# CONFIG_SPI is not set
+CONFIG_ARCH_REQUIRE_GPIOLIB=y
+CONFIG_GPIOLIB=y
+# CONFIG_DEBUG_GPIO is not set
+# CONFIG_GPIO_SYSFS is not set
+
+#
+# Memory mapped GPIO expanders:
+#
+
+#
+# I2C GPIO expanders:
+#
+# CONFIG_GPIO_MAX732X is not set
+# CONFIG_GPIO_PCA953X is not set
+# CONFIG_GPIO_PCF857X is not set
+
+#
+# PCI GPIO expanders:
+#
+
+#
+# SPI GPIO expanders:
+#
+# CONFIG_W1 is not set
+# CONFIG_POWER_SUPPLY is not set
+CONFIG_HWMON=m
+# CONFIG_HWMON_VID is not set
+# CONFIG_SENSORS_AD7414 is not set
+# CONFIG_SENSORS_AD7418 is not set
+CONFIG_SENSORS_ADM1021=m
+# CONFIG_SENSORS_ADM1025 is not set
+# CONFIG_SENSORS_ADM1026 is not set
+# CONFIG_SENSORS_ADM1029 is not set
+# CONFIG_SENSORS_ADM1031 is not set
+# CONFIG_SENSORS_ADM9240 is not set
+# CONFIG_SENSORS_ADT7462 is not set
+# CONFIG_SENSORS_ADT7470 is not set
+# CONFIG_SENSORS_ADT7473 is not set
+# CONFIG_SENSORS_ADT7475 is not set
+# CONFIG_SENSORS_ATXP1 is not set
+# CONFIG_SENSORS_DS1621 is not set
+# CONFIG_SENSORS_F71805F is not set
+# CONFIG_SENSORS_F71882FG is not set
+# CONFIG_SENSORS_F75375S is not set
+# CONFIG_SENSORS_G760A is not set
+# CONFIG_SENSORS_GL518SM is not set
+# CONFIG_SENSORS_GL520SM is not set
+# CONFIG_SENSORS_IT87 is not set
+# CONFIG_SENSORS_LM63 is not set
+# CONFIG_SENSORS_LM75 is not set
+# CONFIG_SENSORS_LM77 is not set
+# CONFIG_SENSORS_LM78 is not set
+# CONFIG_SENSORS_LM80 is not set
+# CONFIG_SENSORS_LM83 is not set
+# CONFIG_SENSORS_LM85 is not set
+# CONFIG_SENSORS_LM87 is not set
+# CONFIG_SENSORS_LM90 is not set
+# CONFIG_SENSORS_LM92 is not set
+# CONFIG_SENSORS_LM93 is not set
+# CONFIG_SENSORS_LTC4215 is not set
+# CONFIG_SENSORS_LTC4245 is not set
+# CONFIG_SENSORS_LM95241 is not set
+# CONFIG_SENSORS_MAX1619 is not set
+CONFIG_SENSORS_MAX6650=m
+# CONFIG_SENSORS_PC87360 is not set
+# CONFIG_SENSORS_PC87427 is not set
+# CONFIG_SENSORS_PCF8591 is not set
+# CONFIG_SENSORS_SHT15 is not set
+# CONFIG_SENSORS_DME1737 is not set
+# CONFIG_SENSORS_SMSC47M1 is not set
+# CONFIG_SENSORS_SMSC47M192 is not set
+# CONFIG_SENSORS_SMSC47B397 is not set
+# CONFIG_SENSORS_ADS7828 is not set
+# CONFIG_SENSORS_THMC50 is not set
+# CONFIG_SENSORS_TMP401 is not set
+# CONFIG_SENSORS_VT1211 is not set
+# CONFIG_SENSORS_W83781D is not set
+# CONFIG_SENSORS_W83791D is not set
+# CONFIG_SENSORS_W83792D is not set
+# CONFIG_SENSORS_W83793 is not set
+# CONFIG_SENSORS_W83L785TS is not set
+# CONFIG_SENSORS_W83L786NG is not set
+# CONFIG_SENSORS_W83627HF is not set
+# CONFIG_SENSORS_W83627EHF is not set
+# CONFIG_HWMON_DEBUG_CHIP is not set
+# CONFIG_THERMAL is not set
+# CONFIG_WATCHDOG is not set
+CONFIG_SSB_POSSIBLE=y
+
+#
+# Sonics Silicon Backplane
+#
+# CONFIG_SSB is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_CORE is not set
+# CONFIG_MFD_SM501 is not set
+# CONFIG_MFD_ASIC3 is not set
+# CONFIG_HTC_EGPIO is not set
+# CONFIG_HTC_PASIC3 is not set
+# CONFIG_TPS65010 is not set
+# CONFIG_MFD_TMIO is not set
+# CONFIG_MFD_T7L66XB is not set
+# CONFIG_MFD_TC6387XB is not set
+# CONFIG_MFD_TC6393XB is not set
+# CONFIG_MFD_WM8400 is not set
+# CONFIG_MFD_WM8350_I2C is not set
+# CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
+# CONFIG_MEDIA_SUPPORT is not set
+
+#
+# Graphics support
+#
+# CONFIG_VGASTATE is not set
+# CONFIG_VIDEO_OUTPUT_CONTROL is not set
+# CONFIG_FB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+
+#
+# Display device support
+#
+# CONFIG_DISPLAY_SUPPORT is not set
+
+#
+# Console display driver support
+#
+# CONFIG_VGA_CONSOLE is not set
+CONFIG_DUMMY_CONSOLE=y
+# CONFIG_SOUND is not set
+# CONFIG_HID_SUPPORT is not set
+# CONFIG_USB_SUPPORT is not set
+# CONFIG_MMC is not set
+# CONFIG_MEMSTICK is not set
+# CONFIG_ACCESSIBILITY is not set
+# CONFIG_NEW_LEDS is not set
+CONFIG_RTC_LIB=y
+CONFIG_RTC_CLASS=m
+
+#
+# RTC interfaces
+#
+CONFIG_RTC_INTF_SYSFS=y
+CONFIG_RTC_INTF_PROC=y
+CONFIG_RTC_INTF_DEV=y
+# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set
+# CONFIG_RTC_DRV_TEST is not set
+
+#
+# I2C RTC drivers
+#
+# CONFIG_RTC_DRV_DS1307 is not set
+# CONFIG_RTC_DRV_DS1374 is not set
+# CONFIG_RTC_DRV_DS1672 is not set
+# CONFIG_RTC_DRV_MAX6900 is not set
+# CONFIG_RTC_DRV_RS5C372 is not set
+# CONFIG_RTC_DRV_ISL1208 is not set
+# CONFIG_RTC_DRV_X1205 is not set
+# CONFIG_RTC_DRV_PCF8563 is not set
+# CONFIG_RTC_DRV_PCF8583 is not set
+# CONFIG_RTC_DRV_M41T80 is not set
+# CONFIG_RTC_DRV_S35390A is not set
+# CONFIG_RTC_DRV_FM3130 is not set
+# CONFIG_RTC_DRV_RX8581 is not set
+# CONFIG_RTC_DRV_RX8025 is not set
+
+#
+# SPI RTC drivers
+#
+
+#
+# Platform RTC drivers
+#
+# CONFIG_RTC_DRV_CMOS is not set
+# CONFIG_RTC_DRV_DS1286 is not set
+# CONFIG_RTC_DRV_DS1511 is not set
+# CONFIG_RTC_DRV_DS1553 is not set
+# CONFIG_RTC_DRV_DS1742 is not set
+# CONFIG_RTC_DRV_STK17TA8 is not set
+# CONFIG_RTC_DRV_M48T86 is not set
+# CONFIG_RTC_DRV_M48T35 is not set
+# CONFIG_RTC_DRV_M48T59 is not set
+# CONFIG_RTC_DRV_BQ4802 is not set
+# CONFIG_RTC_DRV_V3020 is not set
+
+#
+# on-CPU RTC drivers
+#
+CONFIG_RTC_DRV_SA1100=m
+# CONFIG_RTC_DRV_PXA is not set
+CONFIG_DMADEVICES=y
+
+#
+# DMA Devices
+#
+# CONFIG_AUXDISPLAY is not set
+# CONFIG_REGULATOR is not set
+# CONFIG_UIO is not set
+# CONFIG_STAGING is not set
+
+#
+# File systems
+#
+CONFIG_FILE_LOCKING=y
+# CONFIG_FSNOTIFY is not set
+# CONFIG_DNOTIFY is not set
+# CONFIG_INOTIFY is not set
+# CONFIG_INOTIFY_USER is not set
+# CONFIG_QUOTA is not set
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# Caches
+#
+# CONFIG_FSCACHE is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_SYSCTL=y
+CONFIG_PROC_PAGE_MONITOR=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
+# CONFIG_HUGETLB_PAGE is not set
+# CONFIG_CONFIGFS_FS is not set
+CONFIG_MISC_FILESYSTEMS=y
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_FS_DEBUG=0
+CONFIG_JFFS2_FS_WRITEBUFFER=y
+CONFIG_JFFS2_FS_WBUF_VERIFY=y
+# CONFIG_JFFS2_SUMMARY is not set
+# CONFIG_JFFS2_FS_XATTR is not set
+# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
+CONFIG_JFFS2_ZLIB=y
+# CONFIG_JFFS2_LZO is not set
+CONFIG_JFFS2_RTIME=y
+# CONFIG_JFFS2_RUBIN is not set
+# CONFIG_ROMFS_FS is not set
+CONFIG_NETWORK_FILESYSTEMS=y
+CONFIG_NFS_FS=m
+CONFIG_NFS_V3=y
+# CONFIG_NFS_V3_ACL is not set
+# CONFIG_NFS_V4 is not set
+# CONFIG_NFSD is not set
+CONFIG_LOCKD=m
+CONFIG_LOCKD_V4=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=m
+# CONFIG_RPCSEC_GSS_KRB5 is not set
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+CONFIG_NLS=m
+CONFIG_NLS_DEFAULT="utf8"
+# CONFIG_NLS_CODEPAGE_437 is not set
+# CONFIG_NLS_CODEPAGE_737 is not set
+# CONFIG_NLS_CODEPAGE_775 is not set
+# CONFIG_NLS_CODEPAGE_850 is not set
+# CONFIG_NLS_CODEPAGE_852 is not set
+# CONFIG_NLS_CODEPAGE_855 is not set
+# CONFIG_NLS_CODEPAGE_857 is not set
+# CONFIG_NLS_CODEPAGE_860 is not set
+# CONFIG_NLS_CODEPAGE_861 is not set
+# CONFIG_NLS_CODEPAGE_862 is not set
+# CONFIG_NLS_CODEPAGE_863 is not set
+# CONFIG_NLS_CODEPAGE_864 is not set
+# CONFIG_NLS_CODEPAGE_865 is not set
+# CONFIG_NLS_CODEPAGE_866 is not set
+# CONFIG_NLS_CODEPAGE_869 is not set
+# CONFIG_NLS_CODEPAGE_936 is not set
+# CONFIG_NLS_CODEPAGE_950 is not set
+# CONFIG_NLS_CODEPAGE_932 is not set
+# CONFIG_NLS_CODEPAGE_949 is not set
+# CONFIG_NLS_CODEPAGE_874 is not set
+# CONFIG_NLS_ISO8859_8 is not set
+# CONFIG_NLS_CODEPAGE_1250 is not set
+# CONFIG_NLS_CODEPAGE_1251 is not set
+# CONFIG_NLS_ASCII is not set
+# CONFIG_NLS_ISO8859_1 is not set
+# CONFIG_NLS_ISO8859_2 is not set
+# CONFIG_NLS_ISO8859_3 is not set
+# CONFIG_NLS_ISO8859_4 is not set
+# CONFIG_NLS_ISO8859_5 is not set
+# CONFIG_NLS_ISO8859_6 is not set
+# CONFIG_NLS_ISO8859_7 is not set
+# CONFIG_NLS_ISO8859_9 is not set
+# CONFIG_NLS_ISO8859_13 is not set
+# CONFIG_NLS_ISO8859_14 is not set
+# CONFIG_NLS_ISO8859_15 is not set
+# CONFIG_NLS_KOI8_R is not set
+# CONFIG_NLS_KOI8_U is not set
+CONFIG_NLS_UTF8=m
+# CONFIG_DLM is not set
+
+#
+# Kernel hacking
+#
+CONFIG_PRINTK_TIME=y
+CONFIG_ENABLE_WARN_DEPRECATED=y
+CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_FRAME_WARN=1024
+# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
+CONFIG_DEBUG_KERNEL=y
+# CONFIG_DEBUG_SHIRQ is not set
+CONFIG_DETECT_SOFTLOCKUP=y
+# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set
+CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0
+CONFIG_DETECT_HUNG_TASK=y
+# CONFIG_BOOTPARAM_HUNG_TASK_PANIC is not set
+CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=0
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
+# CONFIG_DEBUG_OBJECTS is not set
+# CONFIG_DEBUG_KMEMLEAK is not set
+# CONFIG_DEBUG_RT_MUTEXES is not set
+# CONFIG_RT_MUTEX_TESTER is not set
+# CONFIG_DEBUG_SPINLOCK is not set
+# CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_LOCK_ALLOC is not set
+# CONFIG_PROVE_LOCKING is not set
+# CONFIG_LOCK_STAT is not set
+# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+# CONFIG_DEBUG_KOBJECT is not set
+# CONFIG_DEBUG_BUGVERBOSE is not set
+# CONFIG_DEBUG_INFO is not set
+# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_WRITECOUNT is not set
+# CONFIG_DEBUG_MEMORY_INIT is not set
+# CONFIG_DEBUG_LIST is not set
+# CONFIG_DEBUG_SG is not set
+# CONFIG_DEBUG_NOTIFIERS is not set
+CONFIG_FRAME_POINTER=y
+# CONFIG_BOOT_PRINTK_DELAY is not set
+# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_RCU_CPU_STALL_DETECTOR is not set
+# CONFIG_KPROBES_SANITY_TEST is not set
+# CONFIG_BACKTRACE_SELF_TEST is not set
+# CONFIG_FAULT_INJECTION is not set
+# CONFIG_LATENCYTOP is not set
+CONFIG_SYSCTL_SYSCALL_CHECK=y
+# CONFIG_PAGE_POISONING is not set
+CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_TRACING_SUPPORT=y
+# CONFIG_FTRACE is not set
+# CONFIG_SAMPLES is not set
+CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_KGDB is not set
+# CONFIG_ARM_UNWIND is not set
+# CONFIG_DEBUG_USER is not set
+# CONFIG_DEBUG_ERRORS is not set
+# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_DEBUG_LL is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+# CONFIG_SECURITYFS is not set
+# CONFIG_SECURITY_FILE_CAPABILITIES is not set
+CONFIG_CRYPTO=y
+
+#
+# Crypto core or helper
+#
+# CONFIG_CRYPTO_FIPS is not set
+CONFIG_CRYPTO_ALGAPI=m
+CONFIG_CRYPTO_ALGAPI2=m
+CONFIG_CRYPTO_HASH=m
+CONFIG_CRYPTO_HASH2=m
+# CONFIG_CRYPTO_MANAGER is not set
+# CONFIG_CRYPTO_MANAGER2 is not set
+# CONFIG_CRYPTO_GF128MUL is not set
+# CONFIG_CRYPTO_NULL is not set
+# CONFIG_CRYPTO_CRYPTD is not set
+# CONFIG_CRYPTO_AUTHENC is not set
+# CONFIG_CRYPTO_TEST is not set
+
+#
+# Authenticated Encryption with Associated Data
+#
+# CONFIG_CRYPTO_CCM is not set
+# CONFIG_CRYPTO_GCM is not set
+# CONFIG_CRYPTO_SEQIV is not set
+
+#
+# Block modes
+#
+# CONFIG_CRYPTO_CBC is not set
+# CONFIG_CRYPTO_CTR is not set
+# CONFIG_CRYPTO_CTS is not set
+# CONFIG_CRYPTO_ECB is not set
+# CONFIG_CRYPTO_LRW is not set
+# CONFIG_CRYPTO_PCBC is not set
+# CONFIG_CRYPTO_XTS is not set
+
+#
+# Hash modes
+#
+# CONFIG_CRYPTO_HMAC is not set
+# CONFIG_CRYPTO_XCBC is not set
+
+#
+# Digest
+#
+CONFIG_CRYPTO_CRC32C=m
+# CONFIG_CRYPTO_MD4 is not set
+# CONFIG_CRYPTO_MD5 is not set
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_RMD128 is not set
+# CONFIG_CRYPTO_RMD160 is not set
+# CONFIG_CRYPTO_RMD256 is not set
+# CONFIG_CRYPTO_RMD320 is not set
+# CONFIG_CRYPTO_SHA1 is not set
+# CONFIG_CRYPTO_SHA256 is not set
+# CONFIG_CRYPTO_SHA512 is not set
+# CONFIG_CRYPTO_TGR192 is not set
+# CONFIG_CRYPTO_WP512 is not set
+
+#
+# Ciphers
+#
+# CONFIG_CRYPTO_AES is not set
+# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_CAMELLIA is not set
+# CONFIG_CRYPTO_CAST5 is not set
+# CONFIG_CRYPTO_CAST6 is not set
+# CONFIG_CRYPTO_DES is not set
+# CONFIG_CRYPTO_FCRYPT is not set
+# CONFIG_CRYPTO_KHAZAD is not set
+# CONFIG_CRYPTO_SALSA20 is not set
+# CONFIG_CRYPTO_SEED is not set
+# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_TWOFISH is not set
+
+#
+# Compression
+#
+# CONFIG_CRYPTO_DEFLATE is not set
+# CONFIG_CRYPTO_ZLIB is not set
+# CONFIG_CRYPTO_LZO is not set
+
+#
+# Random Number Generation
+#
+# CONFIG_CRYPTO_ANSI_CPRNG is not set
+# CONFIG_CRYPTO_HW is not set
+# CONFIG_BINARY_PRINTF is not set
+
+#
+# Library routines
+#
+CONFIG_BITREVERSE=y
+CONFIG_GENERIC_FIND_LAST_BIT=y
+# CONFIG_CRC_CCITT is not set
+# CONFIG_CRC16 is not set
+# CONFIG_CRC_T10DIF is not set
+# CONFIG_CRC_ITU_T is not set
+CONFIG_CRC32=y
+# CONFIG_CRC7 is not set
+CONFIG_LIBCRC32C=m
+CONFIG_ZLIB_INFLATE=y
+CONFIG_ZLIB_DEFLATE=y
+CONFIG_DECOMPRESS_GZIP=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
+CONFIG_NLATTR=y
+++ /dev/null
-#
-# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.23
-# Tue Oct 23 13:33:20 2007
-#
-CONFIG_ARM=y
-CONFIG_SYS_SUPPORTS_APM_EMULATION=y
-CONFIG_GENERIC_GPIO=y
-CONFIG_GENERIC_TIME=y
-CONFIG_GENERIC_CLOCKEVENTS=y
-CONFIG_MMU=y
-# CONFIG_NO_IOPORT is not set
-CONFIG_GENERIC_HARDIRQS=y
-CONFIG_STACKTRACE_SUPPORT=y
-CONFIG_LOCKDEP_SUPPORT=y
-CONFIG_TRACE_IRQFLAGS_SUPPORT=y
-CONFIG_HARDIRQS_SW_RESEND=y
-CONFIG_GENERIC_IRQ_PROBE=y
-CONFIG_RWSEM_GENERIC_SPINLOCK=y
-# CONFIG_ARCH_HAS_ILOG2_U32 is not set
-# CONFIG_ARCH_HAS_ILOG2_U64 is not set
-CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
-CONFIG_ZONE_DMA=y
-CONFIG_ARCH_MTD_XIP=y
-CONFIG_VECTORS_BASE=0xffff0000
-CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
-
-#
-# General setup
-#
-CONFIG_EXPERIMENTAL=y
-CONFIG_BROKEN_ON_SMP=y
-CONFIG_INIT_ENV_ARG_LIMIT=32
-CONFIG_LOCALVERSION=""
-CONFIG_LOCALVERSION_AUTO=y
-CONFIG_SWAP=y
-CONFIG_SYSVIPC=y
-CONFIG_SYSVIPC_SYSCTL=y
-# CONFIG_POSIX_MQUEUE is not set
-# CONFIG_BSD_PROCESS_ACCT is not set
-# CONFIG_TASKSTATS is not set
-# CONFIG_USER_NS is not set
-# CONFIG_AUDIT is not set
-# CONFIG_IKCONFIG is not set
-CONFIG_LOG_BUF_SHIFT=18
-# CONFIG_CGROUPS is not set
-CONFIG_FAIR_GROUP_SCHED=y
-CONFIG_FAIR_USER_SCHED=y
-# CONFIG_FAIR_CGROUP_SCHED is not set
-CONFIG_SYSFS_DEPRECATED=y
-# CONFIG_RELAY is not set
-# CONFIG_BLK_DEV_INITRD is not set
-# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
-CONFIG_SYSCTL=y
-# CONFIG_EMBEDDED is not set
-CONFIG_UID16=y
-CONFIG_SYSCTL_SYSCALL=y
-CONFIG_KALLSYMS=y
-# CONFIG_KALLSYMS_EXTRA_PASS is not set
-CONFIG_HOTPLUG=y
-CONFIG_PRINTK=y
-CONFIG_BUG=y
-CONFIG_ELF_CORE=y
-CONFIG_BASE_FULL=y
-CONFIG_FUTEX=y
-CONFIG_ANON_INODES=y
-CONFIG_EPOLL=y
-CONFIG_SIGNALFD=y
-CONFIG_EVENTFD=y
-CONFIG_SHMEM=y
-CONFIG_VM_EVENT_COUNTERS=y
-CONFIG_SLUB_DEBUG=y
-# CONFIG_SLAB is not set
-CONFIG_SLUB=y
-# CONFIG_SLOB is not set
-CONFIG_RT_MUTEXES=y
-# CONFIG_TINY_SHMEM is not set
-CONFIG_BASE_SMALL=0
-CONFIG_MODULES=y
-# CONFIG_MODULE_UNLOAD is not set
-# CONFIG_MODVERSIONS is not set
-# CONFIG_MODULE_SRCVERSION_ALL is not set
-# CONFIG_KMOD is not set
-CONFIG_BLOCK=y
-# CONFIG_LBD is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
-# CONFIG_LSF is not set
-# CONFIG_BLK_DEV_BSG is not set
-
-#
-# IO Schedulers
-#
-CONFIG_IOSCHED_NOOP=y
-CONFIG_IOSCHED_AS=y
-CONFIG_IOSCHED_DEADLINE=y
-CONFIG_IOSCHED_CFQ=y
-# CONFIG_DEFAULT_AS is not set
-# CONFIG_DEFAULT_DEADLINE is not set
-CONFIG_DEFAULT_CFQ=y
-# CONFIG_DEFAULT_NOOP is not set
-CONFIG_DEFAULT_IOSCHED="cfq"
-
-#
-# System Type
-#
-# CONFIG_ARCH_AAEC2000 is not set
-# CONFIG_ARCH_INTEGRATOR is not set
-# CONFIG_ARCH_REALVIEW is not set
-# CONFIG_ARCH_VERSATILE is not set
-# CONFIG_ARCH_AT91 is not set
-# CONFIG_ARCH_CLPS7500 is not set
-# CONFIG_ARCH_CLPS711X is not set
-# CONFIG_ARCH_CO285 is not set
-# CONFIG_ARCH_EBSA110 is not set
-# CONFIG_ARCH_EP93XX is not set
-# CONFIG_ARCH_FOOTBRIDGE is not set
-# CONFIG_ARCH_NETX is not set
-# CONFIG_ARCH_H720X is not set
-# CONFIG_ARCH_IMX is not set
-# CONFIG_ARCH_IOP13XX is not set
-# CONFIG_ARCH_IOP32X is not set
-# CONFIG_ARCH_IOP33X is not set
-# CONFIG_ARCH_IXP23XX is not set
-# CONFIG_ARCH_IXP2000 is not set
-# CONFIG_ARCH_IXP4XX is not set
-# CONFIG_ARCH_L7200 is not set
-# CONFIG_ARCH_KS8695 is not set
-# CONFIG_ARCH_NS9XXX is not set
-# CONFIG_ARCH_MXC is not set
-# CONFIG_ARCH_PNX4008 is not set
-CONFIG_ARCH_PXA=y
-# CONFIG_ARCH_RPC is not set
-# CONFIG_ARCH_SA1100 is not set
-# CONFIG_ARCH_S3C2410 is not set
-# CONFIG_ARCH_SHARK is not set
-# CONFIG_ARCH_LH7A40X is not set
-# CONFIG_ARCH_DAVINCI is not set
-# CONFIG_ARCH_OMAP is not set
-
-#
-# Intel PXA2xx/PXA3xx Implementations
-#
-
-#
-# Supported PXA3xx Processor Variants
-#
-CONFIG_CPU_PXA300=y
-CONFIG_CPU_PXA310=y
-CONFIG_CPU_PXA320=y
-# CONFIG_ARCH_LUBBOCK is not set
-# CONFIG_MACH_LOGICPD_PXA270 is not set
-# CONFIG_MACH_MAINSTONE is not set
-# CONFIG_ARCH_PXA_IDP is not set
-# CONFIG_PXA_SHARPSL is not set
-# CONFIG_MACH_TRIZEPS4 is not set
-# CONFIG_MACH_EM_X270 is not set
-CONFIG_MACH_ZYLONITE=y
-# CONFIG_MACH_ARMCORE is not set
-CONFIG_PXA3xx=y
-
-#
-# Boot options
-#
-
-#
-# Power management
-#
-
-#
-# Processor Type
-#
-CONFIG_CPU_32=y
-CONFIG_CPU_XSC3=y
-CONFIG_CPU_32v5=y
-CONFIG_CPU_ABRT_EV5T=y
-CONFIG_CPU_CACHE_VIVT=y
-CONFIG_CPU_TLB_V4WBI=y
-CONFIG_CPU_CP15=y
-CONFIG_CPU_CP15_MMU=y
-CONFIG_IO_36=y
-
-#
-# Processor Features
-#
-# CONFIG_ARM_THUMB is not set
-# CONFIG_CPU_DCACHE_DISABLE is not set
-# CONFIG_CPU_BPREDICT_DISABLE is not set
-# CONFIG_OUTER_CACHE is not set
-CONFIG_IWMMXT=y
-
-#
-# Bus support
-#
-# CONFIG_PCI_SYSCALL is not set
-# CONFIG_ARCH_SUPPORTS_MSI is not set
-# CONFIG_PCCARD is not set
-
-#
-# Kernel Features
-#
-# CONFIG_TICK_ONESHOT is not set
-# CONFIG_NO_HZ is not set
-# CONFIG_HIGH_RES_TIMERS is not set
-CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
-# CONFIG_PREEMPT is not set
-CONFIG_HZ=100
-CONFIG_AEABI=y
-CONFIG_OABI_COMPAT=y
-# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set
-CONFIG_SELECT_MEMORY_MODEL=y
-CONFIG_FLATMEM_MANUAL=y
-# CONFIG_DISCONTIGMEM_MANUAL is not set
-# CONFIG_SPARSEMEM_MANUAL is not set
-CONFIG_FLATMEM=y
-CONFIG_FLAT_NODE_MEM_MAP=y
-# CONFIG_SPARSEMEM_STATIC is not set
-# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
-CONFIG_SPLIT_PTLOCK_CPUS=4096
-# CONFIG_RESOURCES_64BIT is not set
-CONFIG_ZONE_DMA_FLAG=1
-CONFIG_BOUNCE=y
-CONFIG_VIRT_TO_BUS=y
-CONFIG_ALIGNMENT_TRAP=y
-
-#
-# Boot options
-#
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_CMDLINE="root=/dev/nfs rootfstype=nfs nfsroot=192.168.1.100:/nfs/rootfs/ ip=192.168.1.101:192.168.1.100::255.255.255.0::eth0:on console=ttyS0,38400 mem=64M debug"
-# CONFIG_XIP_KERNEL is not set
-# CONFIG_KEXEC is not set
-
-#
-# Floating point emulation
-#
-
-#
-# At least one emulation must be selected
-#
-CONFIG_FPE_NWFPE=y
-# CONFIG_FPE_NWFPE_XP is not set
-# CONFIG_FPE_FASTFPE is not set
-
-#
-# Userspace binary formats
-#
-CONFIG_BINFMT_ELF=y
-# CONFIG_BINFMT_AOUT is not set
-# CONFIG_BINFMT_MISC is not set
-
-#
-# Power management options
-#
-# CONFIG_PM is not set
-CONFIG_SUSPEND_UP_POSSIBLE=y
-
-#
-# Networking
-#
-CONFIG_NET=y
-
-#
-# Networking options
-#
-CONFIG_PACKET=y
-# CONFIG_PACKET_MMAP is not set
-CONFIG_UNIX=y
-# CONFIG_NET_KEY is not set
-CONFIG_INET=y
-# CONFIG_IP_MULTICAST is not set
-# CONFIG_IP_ADVANCED_ROUTER is not set
-CONFIG_IP_FIB_HASH=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-CONFIG_IP_PNP_BOOTP=y
-CONFIG_IP_PNP_RARP=y
-# CONFIG_NET_IPIP is not set
-# CONFIG_NET_IPGRE is not set
-# CONFIG_ARPD is not set
-# CONFIG_SYN_COOKIES is not set
-# CONFIG_INET_AH is not set
-# CONFIG_INET_ESP is not set
-# CONFIG_INET_IPCOMP is not set
-# CONFIG_INET_XFRM_TUNNEL is not set
-# CONFIG_INET_TUNNEL is not set
-# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
-# CONFIG_INET_XFRM_MODE_TUNNEL is not set
-# CONFIG_INET_XFRM_MODE_BEET is not set
-# CONFIG_INET_LRO is not set
-# CONFIG_INET_DIAG is not set
-# CONFIG_TCP_CONG_ADVANCED is not set
-CONFIG_TCP_CONG_CUBIC=y
-CONFIG_DEFAULT_TCP_CONG="cubic"
-# CONFIG_TCP_MD5SIG is not set
-# CONFIG_IPV6 is not set
-# CONFIG_INET6_XFRM_TUNNEL is not set
-# CONFIG_INET6_TUNNEL is not set
-# CONFIG_NETWORK_SECMARK is not set
-# CONFIG_NETFILTER is not set
-# CONFIG_IP_DCCP is not set
-# CONFIG_IP_SCTP is not set
-# CONFIG_TIPC is not set
-# CONFIG_ATM is not set
-# CONFIG_BRIDGE is not set
-# CONFIG_VLAN_8021Q is not set
-# CONFIG_DECNET is not set
-# CONFIG_LLC2 is not set
-# CONFIG_IPX is not set
-# CONFIG_ATALK is not set
-# CONFIG_X25 is not set
-# CONFIG_LAPB is not set
-# CONFIG_ECONET is not set
-# CONFIG_WAN_ROUTER is not set
-# CONFIG_NET_SCHED is not set
-
-#
-# Network testing
-#
-# CONFIG_NET_PKTGEN is not set
-# CONFIG_HAMRADIO is not set
-# CONFIG_IRDA is not set
-# CONFIG_BT is not set
-# CONFIG_AF_RXRPC is not set
-
-#
-# Wireless
-#
-# CONFIG_CFG80211 is not set
-# CONFIG_WIRELESS_EXT is not set
-# CONFIG_MAC80211 is not set
-# CONFIG_IEEE80211 is not set
-# CONFIG_RFKILL is not set
-# CONFIG_NET_9P is not set
-
-#
-# Device Drivers
-#
-
-#
-# Generic Driver Options
-#
-CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
-CONFIG_STANDALONE=y
-CONFIG_PREVENT_FIRMWARE_BUILD=y
-CONFIG_FW_LOADER=y
-# CONFIG_SYS_HYPERVISOR is not set
-# CONFIG_CONNECTOR is not set
-# CONFIG_MTD is not set
-# CONFIG_PARPORT is not set
-# CONFIG_BLK_DEV is not set
-# CONFIG_MISC_DEVICES is not set
-# CONFIG_IDE is not set
-
-#
-# SCSI device support
-#
-# CONFIG_RAID_ATTRS is not set
-# CONFIG_SCSI is not set
-# CONFIG_SCSI_DMA is not set
-# CONFIG_SCSI_NETLINK is not set
-# CONFIG_ATA is not set
-# CONFIG_MD is not set
-CONFIG_NETDEVICES=y
-# CONFIG_NETDEVICES_MULTIQUEUE is not set
-# CONFIG_DUMMY is not set
-# CONFIG_BONDING is not set
-# CONFIG_MACVLAN is not set
-# CONFIG_EQUALIZER is not set
-# CONFIG_TUN is not set
-# CONFIG_VETH is not set
-# CONFIG_PHYLIB is not set
-CONFIG_NET_ETHERNET=y
-CONFIG_MII=y
-# CONFIG_AX88796 is not set
-CONFIG_SMC91X=y
-# CONFIG_DM9000 is not set
-# CONFIG_SMC911X is not set
-# CONFIG_IBM_NEW_EMAC_ZMII is not set
-# CONFIG_IBM_NEW_EMAC_RGMII is not set
-# CONFIG_IBM_NEW_EMAC_TAH is not set
-# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
-# CONFIG_B44 is not set
-# CONFIG_NETDEV_1000 is not set
-# CONFIG_NETDEV_10000 is not set
-
-#
-# Wireless LAN
-#
-# CONFIG_WLAN_PRE80211 is not set
-# CONFIG_WLAN_80211 is not set
-# CONFIG_WAN is not set
-# CONFIG_PPP is not set
-# CONFIG_SLIP is not set
-# CONFIG_SHAPER is not set
-# CONFIG_NETCONSOLE is not set
-# CONFIG_NETPOLL is not set
-# CONFIG_NET_POLL_CONTROLLER is not set
-# CONFIG_ISDN is not set
-
-#
-# Input device support
-#
-CONFIG_INPUT=y
-# CONFIG_INPUT_FF_MEMLESS is not set
-# CONFIG_INPUT_POLLDEV is not set
-
-#
-# Userland interfaces
-#
-CONFIG_INPUT_MOUSEDEV=y
-# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
-CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
-CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
-# CONFIG_INPUT_JOYDEV is not set
-# CONFIG_INPUT_EVDEV is not set
-# CONFIG_INPUT_EVBUG is not set
-
-#
-# Input Device Drivers
-#
-# CONFIG_INPUT_KEYBOARD is not set
-# CONFIG_INPUT_MOUSE is not set
-# CONFIG_INPUT_JOYSTICK is not set
-# CONFIG_INPUT_TABLET is not set
-# CONFIG_INPUT_TOUCHSCREEN is not set
-# CONFIG_INPUT_MISC is not set
-
-#
-# Hardware I/O ports
-#
-# CONFIG_SERIO is not set
-# CONFIG_GAMEPORT is not set
-
-#
-# Character devices
-#
-CONFIG_VT=y
-CONFIG_VT_CONSOLE=y
-CONFIG_HW_CONSOLE=y
-# CONFIG_VT_HW_CONSOLE_BINDING is not set
-# CONFIG_SERIAL_NONSTANDARD is not set
-
-#
-# Serial drivers
-#
-# CONFIG_SERIAL_8250 is not set
-
-#
-# Non-8250 serial port support
-#
-CONFIG_SERIAL_PXA=y
-CONFIG_SERIAL_PXA_CONSOLE=y
-CONFIG_SERIAL_CORE=y
-CONFIG_SERIAL_CORE_CONSOLE=y
-CONFIG_UNIX98_PTYS=y
-# CONFIG_LEGACY_PTYS is not set
-# CONFIG_IPMI_HANDLER is not set
-# CONFIG_HW_RANDOM is not set
-# CONFIG_NVRAM is not set
-# CONFIG_R3964 is not set
-# CONFIG_RAW_DRIVER is not set
-# CONFIG_TCG_TPM is not set
-# CONFIG_I2C is not set
-
-#
-# SPI support
-#
-# CONFIG_SPI is not set
-# CONFIG_SPI_MASTER is not set
-# CONFIG_W1 is not set
-# CONFIG_POWER_SUPPLY is not set
-# CONFIG_HWMON is not set
-
-#
-# Sonics Silicon Backplane
-#
-CONFIG_SSB_POSSIBLE=y
-# CONFIG_SSB is not set
-
-#
-# Multifunction device drivers
-#
-# CONFIG_MFD_SM501 is not set
-
-#
-# Multimedia devices
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_DAB is not set
-
-#
-# Graphics support
-#
-# CONFIG_VGASTATE is not set
-# CONFIG_VIDEO_OUTPUT_CONTROL is not set
-CONFIG_FB=y
-# CONFIG_FIRMWARE_EDID is not set
-# CONFIG_FB_DDC is not set
-CONFIG_FB_CFB_FILLRECT=y
-CONFIG_FB_CFB_COPYAREA=y
-CONFIG_FB_CFB_IMAGEBLIT=y
-# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
-# CONFIG_FB_SYS_FILLRECT is not set
-# CONFIG_FB_SYS_COPYAREA is not set
-# CONFIG_FB_SYS_IMAGEBLIT is not set
-# CONFIG_FB_SYS_FOPS is not set
-CONFIG_FB_DEFERRED_IO=y
-# CONFIG_FB_SVGALIB is not set
-# CONFIG_FB_MACMODES is not set
-# CONFIG_FB_BACKLIGHT is not set
-# CONFIG_FB_MODE_HELPERS is not set
-# CONFIG_FB_TILEBLITTING is not set
-
-#
-# Frame buffer hardware drivers
-#
-# CONFIG_FB_S1D13XXX is not set
-CONFIG_FB_PXA=y
-# CONFIG_FB_PXA_PARAMETERS is not set
-# CONFIG_FB_MBX is not set
-# CONFIG_FB_VIRTUAL is not set
-# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
-
-#
-# Display device support
-#
-# CONFIG_DISPLAY_SUPPORT is not set
-
-#
-# Console display driver support
-#
-# CONFIG_VGA_CONSOLE is not set
-CONFIG_DUMMY_CONSOLE=y
-CONFIG_FRAMEBUFFER_CONSOLE=y
-CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
-# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
-CONFIG_FONTS=y
-# CONFIG_FONT_8x8 is not set
-# CONFIG_FONT_8x16 is not set
-CONFIG_FONT_6x11=y
-# CONFIG_FONT_7x14 is not set
-# CONFIG_FONT_PEARL_8x8 is not set
-# CONFIG_FONT_ACORN_8x8 is not set
-# CONFIG_FONT_MINI_4x6 is not set
-# CONFIG_FONT_SUN8x16 is not set
-# CONFIG_FONT_SUN12x22 is not set
-# CONFIG_FONT_10x18 is not set
-CONFIG_LOGO=y
-CONFIG_LOGO_LINUX_MONO=y
-CONFIG_LOGO_LINUX_VGA16=y
-CONFIG_LOGO_LINUX_CLUT224=y
-
-#
-# Sound
-#
-# CONFIG_SOUND is not set
-# CONFIG_HID_SUPPORT is not set
-# CONFIG_USB_SUPPORT is not set
-# CONFIG_MMC is not set
-# CONFIG_NEW_LEDS is not set
-CONFIG_RTC_LIB=y
-# CONFIG_RTC_CLASS is not set
-
-#
-# File systems
-#
-# CONFIG_EXT2_FS is not set
-# CONFIG_EXT3_FS is not set
-# CONFIG_EXT4DEV_FS is not set
-# CONFIG_REISERFS_FS is not set
-# CONFIG_JFS_FS is not set
-CONFIG_FS_POSIX_ACL=y
-# CONFIG_XFS_FS is not set
-# CONFIG_GFS2_FS is not set
-# CONFIG_OCFS2_FS is not set
-# CONFIG_MINIX_FS is not set
-# CONFIG_ROMFS_FS is not set
-# CONFIG_INOTIFY is not set
-# CONFIG_QUOTA is not set
-CONFIG_DNOTIFY=y
-# CONFIG_AUTOFS_FS is not set
-# CONFIG_AUTOFS4_FS is not set
-# CONFIG_FUSE_FS is not set
-
-#
-# CD-ROM/DVD Filesystems
-#
-# CONFIG_ISO9660_FS is not set
-# CONFIG_UDF_FS is not set
-
-#
-# DOS/FAT/NT Filesystems
-#
-# CONFIG_MSDOS_FS is not set
-# CONFIG_VFAT_FS is not set
-# CONFIG_NTFS_FS is not set
-
-#
-# Pseudo filesystems
-#
-CONFIG_PROC_FS=y
-CONFIG_PROC_SYSCTL=y
-CONFIG_SYSFS=y
-# CONFIG_TMPFS is not set
-# CONFIG_HUGETLB_PAGE is not set
-# CONFIG_CONFIGFS_FS is not set
-
-#
-# Miscellaneous filesystems
-#
-# CONFIG_ADFS_FS is not set
-# CONFIG_AFFS_FS is not set
-# CONFIG_HFS_FS is not set
-# CONFIG_HFSPLUS_FS is not set
-# CONFIG_BEFS_FS is not set
-# CONFIG_BFS_FS is not set
-# CONFIG_EFS_FS is not set
-# CONFIG_CRAMFS is not set
-# CONFIG_VXFS_FS is not set
-# CONFIG_HPFS_FS is not set
-# CONFIG_QNX4FS_FS is not set
-# CONFIG_SYSV_FS is not set
-# CONFIG_UFS_FS is not set
-CONFIG_NETWORK_FILESYSTEMS=y
-CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
-CONFIG_NFS_V3_ACL=y
-CONFIG_NFS_V4=y
-CONFIG_NFS_DIRECTIO=y
-# CONFIG_NFSD is not set
-CONFIG_ROOT_NFS=y
-CONFIG_LOCKD=y
-CONFIG_LOCKD_V4=y
-CONFIG_NFS_ACL_SUPPORT=y
-CONFIG_NFS_COMMON=y
-CONFIG_SUNRPC=y
-CONFIG_SUNRPC_GSS=y
-# CONFIG_SUNRPC_BIND34 is not set
-CONFIG_RPCSEC_GSS_KRB5=y
-# CONFIG_RPCSEC_GSS_SPKM3 is not set
-# CONFIG_SMB_FS is not set
-# CONFIG_CIFS is not set
-# CONFIG_NCP_FS is not set
-# CONFIG_CODA_FS is not set
-# CONFIG_AFS_FS is not set
-
-#
-# Partition Types
-#
-# CONFIG_PARTITION_ADVANCED is not set
-CONFIG_MSDOS_PARTITION=y
-# CONFIG_NLS is not set
-# CONFIG_DLM is not set
-# CONFIG_INSTRUMENTATION is not set
-
-#
-# Kernel hacking
-#
-# CONFIG_PRINTK_TIME is not set
-CONFIG_ENABLE_MUST_CHECK=y
-# CONFIG_MAGIC_SYSRQ is not set
-# CONFIG_UNUSED_SYMBOLS is not set
-# CONFIG_DEBUG_FS is not set
-# CONFIG_HEADERS_CHECK is not set
-# CONFIG_DEBUG_KERNEL is not set
-# CONFIG_SLUB_DEBUG_ON is not set
-CONFIG_DEBUG_BUGVERBOSE=y
-CONFIG_FRAME_POINTER=y
-# CONFIG_SAMPLES is not set
-CONFIG_DEBUG_USER=y
-
-#
-# Security options
-#
-# CONFIG_KEYS is not set
-# CONFIG_SECURITY is not set
-# CONFIG_SECURITY_FILE_CAPABILITIES is not set
-CONFIG_CRYPTO=y
-CONFIG_CRYPTO_ALGAPI=y
-CONFIG_CRYPTO_BLKCIPHER=y
-CONFIG_CRYPTO_MANAGER=y
-# CONFIG_CRYPTO_HMAC is not set
-# CONFIG_CRYPTO_XCBC is not set
-# CONFIG_CRYPTO_NULL is not set
-# CONFIG_CRYPTO_MD4 is not set
-CONFIG_CRYPTO_MD5=y
-# CONFIG_CRYPTO_SHA1 is not set
-# CONFIG_CRYPTO_SHA256 is not set
-# CONFIG_CRYPTO_SHA512 is not set
-# CONFIG_CRYPTO_WP512 is not set
-# CONFIG_CRYPTO_TGR192 is not set
-# CONFIG_CRYPTO_GF128MUL is not set
-# CONFIG_CRYPTO_ECB is not set
-CONFIG_CRYPTO_CBC=y
-# CONFIG_CRYPTO_PCBC is not set
-# CONFIG_CRYPTO_LRW is not set
-# CONFIG_CRYPTO_XTS is not set
-# CONFIG_CRYPTO_CRYPTD is not set
-CONFIG_CRYPTO_DES=y
-# CONFIG_CRYPTO_FCRYPT is not set
-# CONFIG_CRYPTO_BLOWFISH is not set
-# CONFIG_CRYPTO_TWOFISH is not set
-# CONFIG_CRYPTO_SERPENT is not set
-# CONFIG_CRYPTO_AES is not set
-# CONFIG_CRYPTO_CAST5 is not set
-# CONFIG_CRYPTO_CAST6 is not set
-# CONFIG_CRYPTO_TEA is not set
-# CONFIG_CRYPTO_ARC4 is not set
-# CONFIG_CRYPTO_KHAZAD is not set
-# CONFIG_CRYPTO_ANUBIS is not set
-# CONFIG_CRYPTO_SEED is not set
-# CONFIG_CRYPTO_DEFLATE is not set
-# CONFIG_CRYPTO_MICHAEL_MIC is not set
-# CONFIG_CRYPTO_CRC32C is not set
-# CONFIG_CRYPTO_CAMELLIA is not set
-# CONFIG_CRYPTO_TEST is not set
-# CONFIG_CRYPTO_AUTHENC is not set
-# CONFIG_CRYPTO_HW is not set
-
-#
-# Library routines
-#
-CONFIG_BITREVERSE=y
-# CONFIG_CRC_CCITT is not set
-# CONFIG_CRC16 is not set
-# CONFIG_CRC_ITU_T is not set
-CONFIG_CRC32=y
-# CONFIG_CRC7 is not set
-# CONFIG_LIBCRC32C is not set
-CONFIG_PLIST=y
-CONFIG_HAS_IOMEM=y
-CONFIG_HAS_IOPORT=y
-CONFIG_HAS_DMA=y
#ifdef __KERNEL__
+/*
+ * On ARM, ordinary assignment (str instruction) doesn't clear the local
+ * strex/ldrex monitor on some implementations. The reason we can use it for
+ * atomic_set() is the clrex or dummy strex done on every exception return.
+ */
#define atomic_read(v) ((v)->counter)
+#define atomic_set(v,i) (((v)->counter) = (i))
#if __LINUX_ARM_ARCH__ >= 6
/*
* ARMv6 UP and SMP safe atomic ops. We use load exclusive and
* store exclusive to ensure that these are atomic. We may loop
- * to ensure that the update happens. Writing to 'v->counter'
- * without using the following operations WILL break the atomic
- * nature of these ops.
+ * to ensure that the update happens.
*/
-static inline void atomic_set(atomic_t *v, int i)
-{
- unsigned long tmp;
-
- __asm__ __volatile__("@ atomic_set\n"
-"1: ldrex %0, [%1]\n"
-" strex %0, %2, [%1]\n"
-" teq %0, #0\n"
-" bne 1b"
- : "=&r" (tmp)
- : "r" (&v->counter), "r" (i)
- : "cc");
-}
-
static inline void atomic_add(int i, atomic_t *v)
{
unsigned long tmp;
#error SMP not supported on pre-ARMv6 CPUs
#endif
-#define atomic_set(v,i) (((v)->counter) = (i))
-
static inline int atomic_add_return(int i, atomic_t *v)
{
unsigned long flags;
#ifndef __ASMARM_CACHE_H
#define __ASMARM_CACHE_H
-#define L1_CACHE_SHIFT 5
+#define L1_CACHE_SHIFT CONFIG_ARM_L1_CACHE_SHIFT
#define L1_CACHE_BYTES (1 << L1_CACHE_SHIFT)
/*
return read_cpuid(CPUID_CACHETYPE);
}
+static inline unsigned int __attribute_const__ read_cpuid_tcmstatus(void)
+{
+ return read_cpuid(CPUID_TCM);
+}
+
/*
* Intel's XScale3 core supports some v6 features (supersections, L2)
* but advertises itself as v5 as it does not support the v6 ISA. For
#else
static inline int cpu_is_xsc3(void)
{
- if ((read_cpuid_id() & 0xffffe000) == 0x69056000)
+ unsigned int id;
+ id = read_cpuid_id() & 0xffffe000;
+ /* It covers both Intel ID and Marvell ID */
+ if ((id == 0x69056000) || (id == 0x56056000))
return 1;
return 0;
--- /dev/null
+/*
+ *
+ * Copyright (C) 2008-2009 ST-Ericsson AB
+ * License terms: GNU General Public License (GPL) version 2
+ *
+ * Author: Rickard Andersson <rickard.andersson@stericsson.com>
+ * Author: Linus Walleij <linus.walleij@stericsson.com>
+ *
+ */
+#ifndef __ASMARM_TCM_H
+#define __ASMARM_TCM_H
+
+#ifndef CONFIG_HAVE_TCM
+#error "You should not be including tcm.h unless you have a TCM!"
+#endif
+
+#include <linux/compiler.h>
+
+/* Tag variables with this */
+#define __tcmdata __section(.tcm.data)
+/* Tag constants with this */
+#define __tcmconst __section(.tcm.rodata)
+/* Tag functions inside TCM called from outside TCM with this */
+#define __tcmfunc __attribute__((long_call)) __section(.tcm.text) noinline
+/* Tag function inside TCM called from inside TCM with this */
+#define __tcmlocalfunc __section(.tcm.text)
+
+void *tcm_alloc(size_t len);
+void tcm_free(void *addr, size_t len);
+
+#endif
#define ARM(x...)
#define THUMB(x...) x
+#ifdef __ASSEMBLY__
#define W(instr) instr.w
+#endif
#define BSYM(sym) sym + 1
#else /* !CONFIG_THUMB2_KERNEL */
#define ARM(x...) x
#define THUMB(x...)
+#ifdef __ASSEMBLY__
#define W(instr) instr
+#endif
#define BSYM(sym) sym
#endif /* CONFIG_THUMB2_KERNEL */
obj-$(CONFIG_ARM_THUMBEE) += thumbee.o
obj-$(CONFIG_KGDB) += kgdb.o
obj-$(CONFIG_ARM_UNWIND) += unwind.o
+obj-$(CONFIG_HAVE_TCM) += tcm.o
obj-$(CONFIG_CRUNCH) += crunch.o crunch-bits.o
AFLAGS_crunch-bits.o := -Wa,-mcpu=ep9312
@
@ r0 - instruction
@
+#ifndef CONFIG_THUMB2_KERNEL
ldr r0, [r2, #-4]
+#else
+ ldrh r0, [r2, #-2] @ Thumb instruction at LR - 2
+ and r9, r0, #0xf800
+ cmp r9, #0xe800 @ 32-bit instruction if xx >= 0
+ ldrhhs r9, [r2] @ bottom 16 bits
+ orrhs r0, r9, r0, lsl #16
+#endif
adr r9, BSYM(1f)
bl call_fpe
.word no_fp
.previous
-no_fp: mov pc, lr
+ENTRY(no_fp)
+ mov pc, lr
+ENDPROC(no_fp)
__und_usr_unknown:
enable_irq
#ifdef CONFIG_MMU
ldr r6, [r2, #TI_CPU_DOMAIN]
#endif
-#if __LINUX_ARM_ARCH__ >= 6
-#ifdef CONFIG_CPU_32v6K
- clrex
-#else
- strex r5, r4, [ip] @ Clear exclusive monitor
-#endif
-#endif
#if defined(CONFIG_HAS_TLS_REG)
mcr p15, 0, r3, c13, c0, 3 @ set TLS register
#elif !defined(CONFIG_TLS_REG_EMUL)
#ifndef CONFIG_THUMB2_KERNEL
.macro svc_exit, rpsr
msr spsr_cxsf, \rpsr
+#if defined(CONFIG_CPU_32v6K)
+ clrex @ clear the exclusive monitor
ldmia sp, {r0 - pc}^ @ load r0 - pc, cpsr
+#elif defined (CONFIG_CPU_V6)
+ ldr r0, [sp]
+ strex r1, r2, [sp] @ clear the exclusive monitor
+ ldmib sp, {r1 - pc}^ @ load r1 - pc, cpsr
+#endif
.endm
.macro restore_user_regs, fast = 0, offset = 0
ldr r1, [sp, #\offset + S_PSR] @ get calling cpsr
ldr lr, [sp, #\offset + S_PC]! @ get pc
msr spsr_cxsf, r1 @ save in spsr_svc
+#if defined(CONFIG_CPU_32v6K)
+ clrex @ clear the exclusive monitor
+#elif defined (CONFIG_CPU_V6)
+ strex r1, r2, [sp] @ clear the exclusive monitor
+#endif
.if \fast
ldmdb sp, {r1 - lr}^ @ get calling r1 - lr
.else
.endm
#else /* CONFIG_THUMB2_KERNEL */
.macro svc_exit, rpsr
+ clrex @ clear the exclusive monitor
ldr r0, [sp, #S_SP] @ top of the stack
ldr r1, [sp, #S_PC] @ return address
tst r0, #4 @ orig stack 8-byte aligned?
.endm
.macro restore_user_regs, fast = 0, offset = 0
+ clrex @ clear the exclusive monitor
mov r2, sp
load_user_sp_lr r2, r3, \offset + S_SP @ calling sp, lr
ldr r1, [sp, #\offset + S_PSR] @ get calling cpsr
#include <linux/kernel.h>
#include <linux/kprobes.h>
#include <linux/module.h>
+#include <linux/stop_machine.h>
#include <linux/stringify.h>
#include <asm/traps.h>
#include <asm/cacheflush.h>
flush_insns(p->addr, 1);
}
+/*
+ * The actual disarming is done here on each CPU and synchronized using
+ * stop_machine. This synchronization is necessary on SMP to avoid removing
+ * a probe between the moment the 'Undefined Instruction' exception is raised
+ * and the moment the exception handler reads the faulting instruction from
+ * memory.
+ */
+int __kprobes __arch_disarm_kprobe(void *p)
+{
+ struct kprobe *kp = p;
+ *kp->addr = kp->opcode;
+ flush_insns(kp->addr, 1);
+ return 0;
+}
+
void __kprobes arch_disarm_kprobe(struct kprobe *p)
{
- *p->addr = p->opcode;
- flush_insns(p->addr, 1);
+ stop_machine(__arch_disarm_kprobe, p, &cpu_online_map);
}
void __kprobes arch_remove_kprobe(struct kprobe *p)
#include "compat.h"
#include "atags.h"
+#include "tcm.h"
#ifndef MEM_SIZE
#define MEM_SIZE (16*1024*1024)
#endif
cpu_init();
+ tcm_init();
/*
* Set up various architecture-specific pointers
--- /dev/null
+/*
+ * Copyright (C) 2008-2009 ST-Ericsson AB
+ * License terms: GNU General Public License (GPL) version 2
+ * TCM memory handling for ARM systems
+ *
+ * Author: Linus Walleij <linus.walleij@stericsson.com>
+ * Author: Rickard Andersson <rickard.andersson@stericsson.com>
+ */
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/stddef.h>
+#include <linux/ioport.h>
+#include <linux/genalloc.h>
+#include <linux/string.h> /* memcpy */
+#include <asm/page.h> /* PAGE_SHIFT */
+#include <asm/cputype.h>
+#include <asm/mach/map.h>
+#include <mach/memory.h>
+#include "tcm.h"
+
+/* Scream and warn about misuse */
+#if !defined(ITCM_OFFSET) || !defined(ITCM_END) || \
+ !defined(DTCM_OFFSET) || !defined(DTCM_END)
+#error "TCM support selected but offsets not defined!"
+#endif
+
+static struct gen_pool *tcm_pool;
+
+/* TCM section definitions from the linker */
+extern char __itcm_start, __sitcm_text, __eitcm_text;
+extern char __dtcm_start, __sdtcm_data, __edtcm_data;
+
+/*
+ * TCM memory resources
+ */
+static struct resource dtcm_res = {
+ .name = "DTCM RAM",
+ .start = DTCM_OFFSET,
+ .end = DTCM_END,
+ .flags = IORESOURCE_MEM
+};
+
+static struct resource itcm_res = {
+ .name = "ITCM RAM",
+ .start = ITCM_OFFSET,
+ .end = ITCM_END,
+ .flags = IORESOURCE_MEM
+};
+
+static struct map_desc dtcm_iomap[] __initdata = {
+ {
+ .virtual = DTCM_OFFSET,
+ .pfn = __phys_to_pfn(DTCM_OFFSET),
+ .length = (DTCM_END - DTCM_OFFSET + 1),
+ .type = MT_UNCACHED
+ }
+};
+
+static struct map_desc itcm_iomap[] __initdata = {
+ {
+ .virtual = ITCM_OFFSET,
+ .pfn = __phys_to_pfn(ITCM_OFFSET),
+ .length = (ITCM_END - ITCM_OFFSET + 1),
+ .type = MT_UNCACHED
+ }
+};
+
+/*
+ * Allocate a chunk of TCM memory
+ */
+void *tcm_alloc(size_t len)
+{
+ unsigned long vaddr;
+
+ if (!tcm_pool)
+ return NULL;
+
+ vaddr = gen_pool_alloc(tcm_pool, len);
+ if (!vaddr)
+ return NULL;
+
+ return (void *) vaddr;
+}
+EXPORT_SYMBOL(tcm_alloc);
+
+/*
+ * Free a chunk of TCM memory
+ */
+void tcm_free(void *addr, size_t len)
+{
+ gen_pool_free(tcm_pool, (unsigned long) addr, len);
+}
+EXPORT_SYMBOL(tcm_free);
+
+
+static void __init setup_tcm_bank(u8 type, u32 offset, u32 expected_size)
+{
+ const int tcm_sizes[16] = { 0, -1, -1, 4, 8, 16, 32, 64, 128,
+ 256, 512, 1024, -1, -1, -1, -1 };
+ u32 tcm_region;
+ int tcm_size;
+
+ /* Read the special TCM region register c9, 0 */
+ if (!type)
+ asm("mrc p15, 0, %0, c9, c1, 0"
+ : "=r" (tcm_region));
+ else
+ asm("mrc p15, 0, %0, c9, c1, 1"
+ : "=r" (tcm_region));
+
+ tcm_size = tcm_sizes[(tcm_region >> 2) & 0x0f];
+ if (tcm_size < 0) {
+ pr_err("CPU: %sTCM of unknown size!\n",
+ type ? "I" : "D");
+ } else {
+ pr_info("CPU: found %sTCM %dk @ %08x, %senabled\n",
+ type ? "I" : "D",
+ tcm_size,
+ (tcm_region & 0xfffff000U),
+ (tcm_region & 1) ? "" : "not ");
+ }
+
+ if (tcm_size != expected_size) {
+ pr_crit("CPU: %sTCM was detected %dk but expected %dk!\n",
+ type ? "I" : "D",
+ tcm_size,
+ expected_size);
+ /* Adjust to the expected size? what can we do... */
+ }
+
+ /* Force move the TCM bank to where we want it, enable */
+ tcm_region = offset | (tcm_region & 0x00000ffeU) | 1;
+
+ if (!type)
+ asm("mcr p15, 0, %0, c9, c1, 0"
+ : /* No output operands */
+ : "r" (tcm_region));
+ else
+ asm("mcr p15, 0, %0, c9, c1, 1"
+ : /* No output operands */
+ : "r" (tcm_region));
+
+ pr_debug("CPU: moved %sTCM %dk to %08x, enabled\n",
+ type ? "I" : "D",
+ tcm_size,
+ (tcm_region & 0xfffff000U));
+}
+
+/*
+ * This initializes the TCM memory
+ */
+void __init tcm_init(void)
+{
+ u32 tcm_status = read_cpuid_tcmstatus();
+ char *start;
+ char *end;
+ char *ram;
+
+ /* Setup DTCM if present */
+ if (tcm_status & (1 << 16)) {
+ setup_tcm_bank(0, DTCM_OFFSET,
+ (DTCM_END - DTCM_OFFSET + 1) >> 10);
+ request_resource(&iomem_resource, &dtcm_res);
+ iotable_init(dtcm_iomap, 1);
+ /* Copy data from RAM to DTCM */
+ start = &__sdtcm_data;
+ end = &__edtcm_data;
+ ram = &__dtcm_start;
+ memcpy(start, ram, (end-start));
+ pr_debug("CPU DTCM: copied data from %p - %p\n", start, end);
+ }
+
+ /* Setup ITCM if present */
+ if (tcm_status & 1) {
+ setup_tcm_bank(1, ITCM_OFFSET,
+ (ITCM_END - ITCM_OFFSET + 1) >> 10);
+ request_resource(&iomem_resource, &itcm_res);
+ iotable_init(itcm_iomap, 1);
+ /* Copy code from RAM to ITCM */
+ start = &__sitcm_text;
+ end = &__eitcm_text;
+ ram = &__itcm_start;
+ memcpy(start, ram, (end-start));
+ pr_debug("CPU ITCM: copied code from %p - %p\n", start, end);
+ }
+}
+
+/*
+ * This creates the TCM memory pool and has to be done later,
+ * during the core_initicalls, since the allocator is not yet
+ * up and running when the first initialization runs.
+ */
+static int __init setup_tcm_pool(void)
+{
+ u32 tcm_status = read_cpuid_tcmstatus();
+ u32 dtcm_pool_start = (u32) &__edtcm_data;
+ u32 itcm_pool_start = (u32) &__eitcm_text;
+ int ret;
+
+ /*
+ * Set up malloc pool, 2^2 = 4 bytes granularity since
+ * the TCM is sometimes just 4 KiB. NB: pages and cache
+ * line alignments does not matter in TCM!
+ */
+ tcm_pool = gen_pool_create(2, -1);
+
+ pr_debug("Setting up TCM memory pool\n");
+
+ /* Add the rest of DTCM to the TCM pool */
+ if (tcm_status & (1 << 16)) {
+ if (dtcm_pool_start < DTCM_END) {
+ ret = gen_pool_add(tcm_pool, dtcm_pool_start,
+ DTCM_END - dtcm_pool_start + 1, -1);
+ if (ret) {
+ pr_err("CPU DTCM: could not add DTCM " \
+ "remainder to pool!\n");
+ return ret;
+ }
+ pr_debug("CPU DTCM: Added %08x bytes @ %08x to " \
+ "the TCM memory pool\n",
+ DTCM_END - dtcm_pool_start + 1,
+ dtcm_pool_start);
+ }
+ }
+
+ /* Add the rest of ITCM to the TCM pool */
+ if (tcm_status & 1) {
+ if (itcm_pool_start < ITCM_END) {
+ ret = gen_pool_add(tcm_pool, itcm_pool_start,
+ ITCM_END - itcm_pool_start + 1, -1);
+ if (ret) {
+ pr_err("CPU ITCM: could not add ITCM " \
+ "remainder to pool!\n");
+ return ret;
+ }
+ pr_debug("CPU ITCM: Added %08x bytes @ %08x to " \
+ "the TCM memory pool\n",
+ ITCM_END - itcm_pool_start + 1,
+ itcm_pool_start);
+ }
+ }
+ return 0;
+}
+
+core_initcall(setup_tcm_pool);
--- /dev/null
+/*
+ * Copyright (C) 2008-2009 ST-Ericsson AB
+ * License terms: GNU General Public License (GPL) version 2
+ * TCM memory handling for ARM systems
+ *
+ * Author: Linus Walleij <linus.walleij@stericsson.com>
+ * Author: Rickard Andersson <rickard.andersson@stericsson.com>
+ */
+
+#ifdef CONFIG_HAVE_TCM
+void __init tcm_init(void);
+#else
+/* No TCM support, just blank inlines to be optimized out */
+inline void tcm_init(void)
+{
+}
+#endif
}
_edata_loc = __data_loc + SIZEOF(.data);
+#ifdef CONFIG_HAVE_TCM
+ /*
+ * We align everything to a page boundary so we can
+ * free it after init has commenced and TCM contents have
+ * been copied to its destination.
+ */
+ .tcm_start : {
+ . = ALIGN(PAGE_SIZE);
+ __tcm_start = .;
+ __itcm_start = .;
+ }
+
+ /*
+ * Link these to the ITCM RAM
+ * Put VMA to the TCM address and LMA to the common RAM
+ * and we'll upload the contents from RAM to TCM and free
+ * the used RAM after that.
+ */
+ .text_itcm ITCM_OFFSET : AT(__itcm_start)
+ {
+ __sitcm_text = .;
+ *(.tcm.text)
+ *(.tcm.rodata)
+ . = ALIGN(4);
+ __eitcm_text = .;
+ }
+
+ /*
+ * Reset the dot pointer, this is needed to create the
+ * relative __dtcm_start below (to be used as extern in code).
+ */
+ . = ADDR(.tcm_start) + SIZEOF(.tcm_start) + SIZEOF(.text_itcm);
+
+ .dtcm_start : {
+ __dtcm_start = .;
+ }
+
+ /* TODO: add remainder of ITCM as well, that can be used for data! */
+ .data_dtcm DTCM_OFFSET : AT(__dtcm_start)
+ {
+ . = ALIGN(4);
+ __sdtcm_data = .;
+ *(.tcm.data)
+ . = ALIGN(4);
+ __edtcm_data = .;
+ }
+
+ /* Reset the dot pointer or the linker gets confused */
+ . = ADDR(.dtcm_start) + SIZEOF(.data_dtcm);
+
+ /* End marker for freeing TCM copy in linked object */
+ .tcm_end : AT(ADDR(.dtcm_start) + SIZEOF(.data_dtcm)){
+ . = ALIGN(PAGE_SIZE);
+ __tcm_end = .;
+ }
+#endif
+
.bss : {
__bss_start = .; /* BSS */
*(.bss)
#include <linux/linkage.h>
#include <asm/assembler.h>
#include <asm/asm-offsets.h>
+#include <asm/cache.h>
-#define COPY_COUNT (PAGE_SZ/64 PLD( -1 ))
+#define COPY_COUNT (PAGE_SZ / (2 * L1_CACHE_BYTES) PLD( -1 ))
.text
.align 5
ENTRY(copy_page)
stmfd sp!, {r4, lr} @ 2
PLD( pld [r1, #0] )
- PLD( pld [r1, #32] )
+ PLD( pld [r1, #L1_CACHE_BYTES] )
mov r2, #COPY_COUNT @ 1
ldmia r1!, {r3, r4, ip, lr} @ 4+1
-1: PLD( pld [r1, #64] )
- PLD( pld [r1, #96] )
-2: stmia r0!, {r3, r4, ip, lr} @ 4
- ldmia r1!, {r3, r4, ip, lr} @ 4+1
- stmia r0!, {r3, r4, ip, lr} @ 4
- ldmia r1!, {r3, r4, ip, lr} @ 4+1
+1: PLD( pld [r1, #2 * L1_CACHE_BYTES])
+ PLD( pld [r1, #3 * L1_CACHE_BYTES])
+2:
+ .rept (2 * L1_CACHE_BYTES / 16 - 1)
stmia r0!, {r3, r4, ip, lr} @ 4
ldmia r1!, {r3, r4, ip, lr} @ 4
+ .endr
subs r2, r2, #1 @ 1
stmia r0!, {r3, r4, ip, lr} @ 4
ldmgtia r1!, {r3, r4, ip, lr} @ 4
* AC97
* -------------------------------------------------------------------- */
-#if defined(CONFIG_SND_AT91_AC97) || defined(CONFIG_SND_AT91_AC97_MODULE)
+#if defined(CONFIG_SND_ATMEL_AC97C) || defined(CONFIG_SND_ATMEL_AC97C_MODULE)
static u64 ac97_dmamask = DMA_BIT_MASK(32);
-static struct atmel_ac97_data ac97_data;
+static struct ac97c_platform_data ac97_data;
static struct resource ac97_resources[] = {
[0] = {
};
static struct platform_device at91cap9_ac97_device = {
- .name = "ac97c",
+ .name = "atmel_ac97c",
.id = 1,
.dev = {
.dma_mask = &ac97_dmamask,
.num_resources = ARRAY_SIZE(ac97_resources),
};
-void __init at91_add_device_ac97(struct atmel_ac97_data *data)
+void __init at91_add_device_ac97(struct ac97c_platform_data *data)
{
if (!data)
return;
platform_device_register(&at91cap9_ac97_device);
}
#else
-void __init at91_add_device_ac97(struct atmel_ac97_data *data) {}
+void __init at91_add_device_ac97(struct ac97c_platform_data *data) {}
#endif
#include <mach/at91sam9g45.h>
#include <mach/at91sam9g45_matrix.h>
#include <mach/at91sam9_smc.h>
+#include <mach/at_hdmac.h>
#include "generic.h"
+/* --------------------------------------------------------------------
+ * HDMAC - AHB DMA Controller
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_AT_HDMAC) || defined(CONFIG_AT_HDMAC_MODULE)
+static u64 hdmac_dmamask = DMA_BIT_MASK(32);
+
+static struct at_dma_platform_data atdma_pdata = {
+ .nr_channels = 8,
+};
+
+static struct resource hdmac_resources[] = {
+ [0] = {
+ .start = AT91_BASE_SYS + AT91_DMA,
+ .end = AT91_BASE_SYS + AT91_DMA + SZ_512 - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [2] = {
+ .start = AT91SAM9G45_ID_DMA,
+ .end = AT91SAM9G45_ID_DMA,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device at_hdmac_device = {
+ .name = "at_hdmac",
+ .id = -1,
+ .dev = {
+ .dma_mask = &hdmac_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ .platform_data = &atdma_pdata,
+ },
+ .resource = hdmac_resources,
+ .num_resources = ARRAY_SIZE(hdmac_resources),
+};
+
+void __init at91_add_device_hdmac(void)
+{
+ dma_cap_set(DMA_MEMCPY, atdma_pdata.cap_mask);
+ dma_cap_set(DMA_SLAVE, atdma_pdata.cap_mask);
+ platform_device_register(&at_hdmac_device);
+}
+#else
+void __init at91_add_device_hdmac(void) {}
+#endif
+
+
/* --------------------------------------------------------------------
* USB Host (OHCI)
* -------------------------------------------------------------------- */
#endif
+/* --------------------------------------------------------------------
+ * AC97
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_SND_ATMEL_AC97C) || defined(CONFIG_SND_ATMEL_AC97C_MODULE)
+static u64 ac97_dmamask = DMA_BIT_MASK(32);
+static struct ac97c_platform_data ac97_data;
+
+static struct resource ac97_resources[] = {
+ [0] = {
+ .start = AT91SAM9G45_BASE_AC97C,
+ .end = AT91SAM9G45_BASE_AC97C + SZ_16K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AT91SAM9G45_ID_AC97C,
+ .end = AT91SAM9G45_ID_AC97C,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device at91sam9g45_ac97_device = {
+ .name = "atmel_ac97c",
+ .id = 0,
+ .dev = {
+ .dma_mask = &ac97_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ .platform_data = &ac97_data,
+ },
+ .resource = ac97_resources,
+ .num_resources = ARRAY_SIZE(ac97_resources),
+};
+
+void __init at91_add_device_ac97(struct ac97c_platform_data *data)
+{
+ if (!data)
+ return;
+
+ at91_set_A_periph(AT91_PIN_PD8, 0); /* AC97FS */
+ at91_set_A_periph(AT91_PIN_PD9, 0); /* AC97CK */
+ at91_set_A_periph(AT91_PIN_PD7, 0); /* AC97TX */
+ at91_set_A_periph(AT91_PIN_PD6, 0); /* AC97RX */
+
+ /* reset */
+ if (data->reset_pin)
+ at91_set_gpio_output(data->reset_pin, 0);
+
+ ac97_data = *data;
+ platform_device_register(&at91sam9g45_ac97_device);
+}
+#else
+void __init at91_add_device_ac97(struct ac97c_platform_data *data) {}
+#endif
+
+
/* --------------------------------------------------------------------
* LCD Controller
* -------------------------------------------------------------------- */
*/
static int __init at91_add_standard_devices(void)
{
+ at91_add_device_hdmac();
at91_add_device_rtc();
at91_add_device_rtt();
at91_add_device_watchdog();
#include <mach/at91sam9rl.h>
#include <mach/at91sam9rl_matrix.h>
#include <mach/at91sam9_smc.h>
+#include <mach/at_hdmac.h>
#include "generic.h"
+/* --------------------------------------------------------------------
+ * HDMAC - AHB DMA Controller
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_AT_HDMAC) || defined(CONFIG_AT_HDMAC_MODULE)
+static u64 hdmac_dmamask = DMA_BIT_MASK(32);
+
+static struct at_dma_platform_data atdma_pdata = {
+ .nr_channels = 2,
+};
+
+static struct resource hdmac_resources[] = {
+ [0] = {
+ .start = AT91_BASE_SYS + AT91_DMA,
+ .end = AT91_BASE_SYS + AT91_DMA + SZ_512 - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [2] = {
+ .start = AT91SAM9RL_ID_DMA,
+ .end = AT91SAM9RL_ID_DMA,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device at_hdmac_device = {
+ .name = "at_hdmac",
+ .id = -1,
+ .dev = {
+ .dma_mask = &hdmac_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ .platform_data = &atdma_pdata,
+ },
+ .resource = hdmac_resources,
+ .num_resources = ARRAY_SIZE(hdmac_resources),
+};
+
+void __init at91_add_device_hdmac(void)
+{
+ dma_cap_set(DMA_MEMCPY, atdma_pdata.cap_mask);
+ platform_device_register(&at_hdmac_device);
+}
+#else
+void __init at91_add_device_hdmac(void) {}
+#endif
+
/* --------------------------------------------------------------------
* USB HS Device (Gadget)
* -------------------------------------------------------------------- */
#endif
+/* --------------------------------------------------------------------
+ * AC97
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_SND_ATMEL_AC97C) || defined(CONFIG_SND_ATMEL_AC97C_MODULE)
+static u64 ac97_dmamask = DMA_BIT_MASK(32);
+static struct ac97c_platform_data ac97_data;
+
+static struct resource ac97_resources[] = {
+ [0] = {
+ .start = AT91SAM9RL_BASE_AC97C,
+ .end = AT91SAM9RL_BASE_AC97C + SZ_16K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AT91SAM9RL_ID_AC97C,
+ .end = AT91SAM9RL_ID_AC97C,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device at91sam9rl_ac97_device = {
+ .name = "atmel_ac97c",
+ .id = 0,
+ .dev = {
+ .dma_mask = &ac97_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ .platform_data = &ac97_data,
+ },
+ .resource = ac97_resources,
+ .num_resources = ARRAY_SIZE(ac97_resources),
+};
+
+void __init at91_add_device_ac97(struct ac97c_platform_data *data)
+{
+ if (!data)
+ return;
+
+ at91_set_A_periph(AT91_PIN_PD1, 0); /* AC97FS */
+ at91_set_A_periph(AT91_PIN_PD2, 0); /* AC97CK */
+ at91_set_A_periph(AT91_PIN_PD3, 0); /* AC97TX */
+ at91_set_A_periph(AT91_PIN_PD4, 0); /* AC97RX */
+
+ /* reset */
+ if (data->reset_pin)
+ at91_set_gpio_output(data->reset_pin, 0);
+
+ ac97_data = *data;
+ platform_device_register(&at91sam9rl_ac97_device);
+}
+#else
+void __init at91_add_device_ac97(struct ac97c_platform_data *data) {}
+#endif
+
+
/* --------------------------------------------------------------------
* LCD Controller
* -------------------------------------------------------------------- */
*/
static int __init at91_add_standard_devices(void)
{
+ at91_add_device_hdmac();
at91_add_device_rtc();
at91_add_device_rtt();
at91_add_device_watchdog();
/*
* AC97
*/
-static struct atmel_ac97_data cap9adk_ac97_data = {
+static struct ac97c_platform_data cap9adk_ac97_data = {
// .reset_pin = ... not connected
};
/*
* AC97
*/
-static struct atmel_ac97_data neocore926_ac97_data = {
+static struct ac97c_platform_data neocore926_ac97_data = {
.reset_pin = AT91_PIN_PA13,
};
#endif
+/*
+ * AC97
+ * reset_pin is not connected: NRST
+ */
+static struct ac97c_platform_data ek_ac97_data = {
+};
+
+
/*
* LEDs ... these could all be PWM-driven, for variable brightness
*/
at91_add_device_lcdc(&ek_lcdc_data);
/* Push Buttons */
ek_add_device_buttons();
+ /* AC97 */
+ at91_add_device_ac97(&ek_ac97_data);
/* LEDs */
at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
at91_pwm_leds(ek_pwm_led, ARRAY_SIZE(ek_pwm_led));
#endif
+/*
+ * AC97
+ * reset_pin is not connected: NRST
+ */
+static struct ac97c_platform_data ek_ac97_data = {
+};
+
+
/*
* LEDs
*/
at91_add_device_mmc(0, &ek_mmc_data);
/* LCD Controller */
at91_add_device_lcdc(&ek_lcdc_data);
+ /* AC97 */
+ at91_add_device_ac97(&ek_ac97_data);
/* Touch Screen Controller */
at91_add_device_tsadcc();
/* LEDs */
#include <linux/amba/bus.h>
#include <linux/amba/kmi.h>
#include <linux/amba/clcd.h>
+#include <linux/amba/mmci.h>
#include <linux/io.h>
#include <asm/clkdev.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
#include <asm/mach/irq.h>
-#include <asm/mach/mmc.h>
#include <asm/mach/map.h>
#include <asm/mach/time.h>
return status & 8;
}
-static struct mmc_platform_data mmc_data = {
+static struct mmci_platform_data mmc_data = {
.ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
.status = mmc_status,
.gpio_wp = -1,
config CPU_PXA935
bool "PXA935 (codename Tavor-P65)"
+ select CPU_PXA930
+
+config CPU_PXA950
+ bool "PXA950 (codename Tavor-PV2)"
+ select CPU_PXA930
endmenu
bool "Nec Mobilepro 900/c"
select PXA25x
+config MACH_BALLOON3
+ bool "Balloon 3 board"
+ select PXA27x
+ select IWMMXT
+ select PXA_HAVE_BOARD_IRQS
+
config ARCH_PXA_IDP
bool "Accelent Xscale IDP"
select PXA25x
Say Y here if you intend to run this kernel on a Palm Tungsten|E2
handheld computer.
+config MACH_PALMTC
+ bool "Palm Tungsten|C"
+ default y
+ depends on ARCH_PXA_PALM
+ select PXA25x
+ help
+ Say Y here if you intend to run this kernel on a Palm Tungsten|C
+ handheld computer.
+
config MACH_PALMT5
bool "Palm Tungsten|T5"
default y
select PXA27x
select IWMMXT
select HAVE_PWM
+ select PXA_HAVE_BOARD_IRQS
config MACH_EZX_A780
bool "Motorola EZX A780"
default y
depends on PXA_EZX
+config MACH_XCEP
+ bool "Iskratel Electronics XCEP"
+ select PXA25x
+ select MTD
+ select MTD_PARTITIONS
+ select MTD_PHYSMAP
+ select MTD_CFI_INTELEXT
+ select MTD_CFI
+ select MTD_CHAR
+ select SMC91X
+ select PXA_SSP
+ help
+ PXA255 based Single Board Computer with SMC 91C111 ethernet chip and 64 MB of flash.
+ Tuned for usage in Libera instruments for particle accelerators.
+
endmenu
config PXA25x
obj-$(CONFIG_ARCH_LUBBOCK) += lubbock.o
obj-$(CONFIG_MACH_LOGICPD_PXA270) += lpd270.o
obj-$(CONFIG_MACH_MAINSTONE) += mainstone.o
+obj-$(CONFIG_MACH_BALLOON3) += balloon3.o
obj-$(CONFIG_MACH_MP900C) += mp900.o
obj-$(CONFIG_ARCH_PXA_IDP) += idp.o
obj-$(CONFIG_MACH_TRIZEPS4) += trizeps4.o
obj-$(CONFIG_MACH_E400) += e400.o
obj-$(CONFIG_MACH_E800) += e800.o
obj-$(CONFIG_MACH_PALMTE2) += palmte2.o
+obj-$(CONFIG_MACH_PALMTC) += palmtc.o
obj-$(CONFIG_MACH_PALMT5) += palmt5.o
obj-$(CONFIG_MACH_PALMTX) += palmtx.o
obj-$(CONFIG_MACH_PALMLD) += palmld.o
obj-$(CONFIG_MACH_CM_X300) += cm-x300.o
obj-$(CONFIG_PXA_EZX) += ezx.o
+obj-$(CONFIG_MACH_XCEP) += xcep.o
+
obj-$(CONFIG_MACH_INTELMOTE2) += imote2.o
obj-$(CONFIG_MACH_STARGATE2) += stargate2.o
obj-$(CONFIG_MACH_CSB726) += csb726.o
--- /dev/null
+/*
+ * linux/arch/arm/mach-pxa/balloon3.c
+ *
+ * Support for Balloonboard.org Balloon3 board.
+ *
+ * Author: Nick Bane, Wookey, Jonathan McDowell
+ * Created: June, 2006
+ * Copyright: Toby Churchill Ltd
+ * Derived from mainstone.c, by Nico Pitre
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/sysdev.h>
+#include <linux/interrupt.h>
+#include <linux/sched.h>
+#include <linux/bitops.h>
+#include <linux/fb.h>
+#include <linux/gpio.h>
+#include <linux/ioport.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/types.h>
+
+#include <asm/setup.h>
+#include <asm/mach-types.h>
+#include <asm/irq.h>
+#include <asm/sizes.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+#include <asm/mach/flash.h>
+
+#include <mach/pxa27x.h>
+#include <mach/balloon3.h>
+#include <mach/audio.h>
+#include <mach/pxafb.h>
+#include <mach/mmc.h>
+#include <mach/udc.h>
+#include <mach/pxa27x-udc.h>
+#include <mach/irda.h>
+#include <mach/ohci.h>
+
+#include <plat/i2c.h>
+
+#include "generic.h"
+#include "devices.h"
+
+static unsigned long balloon3_irq_enabled;
+
+static unsigned long balloon3_features_present =
+ (1 << BALLOON3_FEATURE_OHCI) | (1 << BALLOON3_FEATURE_CF) |
+ (1 << BALLOON3_FEATURE_AUDIO) |
+ (1 << BALLOON3_FEATURE_TOPPOLY);
+
+int balloon3_has(enum balloon3_features feature)
+{
+ return (balloon3_features_present & (1 << feature)) ? 1 : 0;
+}
+EXPORT_SYMBOL_GPL(balloon3_has);
+
+int __init parse_balloon3_features(char *arg)
+{
+ if (!arg)
+ return 0;
+
+ return strict_strtoul(arg, 0, &balloon3_features_present);
+}
+early_param("balloon3_features", parse_balloon3_features);
+
+static void balloon3_mask_irq(unsigned int irq)
+{
+ int balloon3_irq = (irq - BALLOON3_IRQ(0));
+ balloon3_irq_enabled &= ~(1 << balloon3_irq);
+ __raw_writel(~balloon3_irq_enabled, BALLOON3_INT_CONTROL_REG);
+}
+
+static void balloon3_unmask_irq(unsigned int irq)
+{
+ int balloon3_irq = (irq - BALLOON3_IRQ(0));
+ balloon3_irq_enabled |= (1 << balloon3_irq);
+ __raw_writel(~balloon3_irq_enabled, BALLOON3_INT_CONTROL_REG);
+}
+
+static struct irq_chip balloon3_irq_chip = {
+ .name = "FPGA",
+ .ack = balloon3_mask_irq,
+ .mask = balloon3_mask_irq,
+ .unmask = balloon3_unmask_irq,
+};
+
+static void balloon3_irq_handler(unsigned int irq, struct irq_desc *desc)
+{
+ unsigned long pending = __raw_readl(BALLOON3_INT_CONTROL_REG) &
+ balloon3_irq_enabled;
+
+ do {
+ /* clear useless edge notification */
+ if (desc->chip->ack)
+ desc->chip->ack(BALLOON3_AUX_NIRQ);
+ while (pending) {
+ irq = BALLOON3_IRQ(0) + __ffs(pending);
+ generic_handle_irq(irq);
+ pending &= pending - 1;
+ }
+ pending = __raw_readl(BALLOON3_INT_CONTROL_REG) &
+ balloon3_irq_enabled;
+ } while (pending);
+}
+
+static void __init balloon3_init_irq(void)
+{
+ int irq;
+
+ pxa27x_init_irq();
+ /* setup extra Balloon3 irqs */
+ for (irq = BALLOON3_IRQ(0); irq <= BALLOON3_IRQ(7); irq++) {
+ set_irq_chip(irq, &balloon3_irq_chip);
+ set_irq_handler(irq, handle_level_irq);
+ set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
+ }
+
+ set_irq_chained_handler(BALLOON3_AUX_NIRQ, balloon3_irq_handler);
+ set_irq_type(BALLOON3_AUX_NIRQ, IRQ_TYPE_EDGE_FALLING);
+
+ pr_debug("%s: chained handler installed - irq %d automatically "
+ "enabled\n", __func__, BALLOON3_AUX_NIRQ);
+}
+
+static void balloon3_backlight_power(int on)
+{
+ pr_debug("%s: power is %s\n", __func__, on ? "on" : "off");
+ gpio_set_value(BALLOON3_GPIO_RUN_BACKLIGHT, on);
+}
+
+static unsigned long balloon3_lcd_pin_config[] = {
+ /* LCD - 16bpp Active TFT */
+ GPIO58_LCD_LDD_0,
+ GPIO59_LCD_LDD_1,
+ GPIO60_LCD_LDD_2,
+ GPIO61_LCD_LDD_3,
+ GPIO62_LCD_LDD_4,
+ GPIO63_LCD_LDD_5,
+ GPIO64_LCD_LDD_6,
+ GPIO65_LCD_LDD_7,
+ GPIO66_LCD_LDD_8,
+ GPIO67_LCD_LDD_9,
+ GPIO68_LCD_LDD_10,
+ GPIO69_LCD_LDD_11,
+ GPIO70_LCD_LDD_12,
+ GPIO71_LCD_LDD_13,
+ GPIO72_LCD_LDD_14,
+ GPIO73_LCD_LDD_15,
+ GPIO74_LCD_FCLK,
+ GPIO75_LCD_LCLK,
+ GPIO76_LCD_PCLK,
+ GPIO77_LCD_BIAS,
+
+ GPIO99_GPIO, /* Backlight */
+};
+
+static struct pxafb_mode_info balloon3_lcd_modes[] = {
+ {
+ .pixclock = 38000,
+ .xres = 480,
+ .yres = 640,
+ .bpp = 16,
+ .hsync_len = 8,
+ .left_margin = 8,
+ .right_margin = 8,
+ .vsync_len = 2,
+ .upper_margin = 4,
+ .lower_margin = 5,
+ .sync = 0,
+ },
+};
+
+static struct pxafb_mach_info balloon3_pxafb_info = {
+ .modes = balloon3_lcd_modes,
+ .num_modes = ARRAY_SIZE(balloon3_lcd_modes),
+ .lcd_conn = LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL,
+ .pxafb_backlight_power = balloon3_backlight_power,
+};
+
+static unsigned long balloon3_mmc_pin_config[] = {
+ GPIO32_MMC_CLK,
+ GPIO92_MMC_DAT_0,
+ GPIO109_MMC_DAT_1,
+ GPIO110_MMC_DAT_2,
+ GPIO111_MMC_DAT_3,
+ GPIO112_MMC_CMD,
+};
+
+static void balloon3_mci_setpower(struct device *dev, unsigned int vdd)
+{
+ struct pxamci_platform_data *p_d = dev->platform_data;
+
+ if ((1 << vdd) & p_d->ocr_mask) {
+ pr_debug("%s: on\n", __func__);
+ /* FIXME something to prod here? */
+ } else {
+ pr_debug("%s: off\n", __func__);
+ /* FIXME something to prod here? */
+ }
+}
+
+static struct pxamci_platform_data balloon3_mci_platform_data = {
+ .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
+ .setpower = balloon3_mci_setpower,
+};
+
+static int balloon3_udc_is_connected(void)
+{
+ pr_debug("%s: udc connected\n", __func__);
+ return 1;
+}
+
+static void balloon3_udc_command(int cmd)
+{
+ switch (cmd) {
+ case PXA2XX_UDC_CMD_CONNECT:
+ UP2OCR |= (UP2OCR_DPPUE + UP2OCR_DPPUBE);
+ pr_debug("%s: connect\n", __func__);
+ break;
+ case PXA2XX_UDC_CMD_DISCONNECT:
+ UP2OCR &= ~UP2OCR_DPPUE;
+ pr_debug("%s: disconnect\n", __func__);
+ break;
+ }
+}
+
+static struct pxa2xx_udc_mach_info balloon3_udc_info = {
+ .udc_is_connected = balloon3_udc_is_connected,
+ .udc_command = balloon3_udc_command,
+};
+
+static struct pxaficp_platform_data balloon3_ficp_platform_data = {
+ .transceiver_cap = IR_SIRMODE | IR_FIRMODE | IR_OFF,
+};
+
+static unsigned long balloon3_ohci_pin_config[] = {
+ GPIO88_USBH1_PWR,
+ GPIO89_USBH1_PEN,
+};
+
+static struct pxaohci_platform_data balloon3_ohci_platform_data = {
+ .port_mode = PMM_PERPORT_MODE,
+ .flags = ENABLE_PORT_ALL | POWER_CONTROL_LOW | POWER_SENSE_LOW,
+};
+
+static unsigned long balloon3_pin_config[] __initdata = {
+ /* Select BTUART 'COM1/ttyS0' as IO option for pins 42/43/44/45 */
+ GPIO42_BTUART_RXD,
+ GPIO43_BTUART_TXD,
+ GPIO44_BTUART_CTS,
+ GPIO45_BTUART_RTS,
+
+ /* Wakeup GPIO */
+ GPIO1_GPIO | WAKEUP_ON_EDGE_BOTH,
+
+ /* NAND & IDLE LED GPIOs */
+ GPIO9_GPIO,
+ GPIO10_GPIO,
+};
+
+static struct gpio_led balloon3_gpio_leds[] = {
+ {
+ .name = "balloon3:green:idle",
+ .default_trigger = "heartbeat",
+ .gpio = BALLOON3_GPIO_LED_IDLE,
+ .active_low = 1,
+ },
+ {
+ .name = "balloon3:green:nand",
+ .default_trigger = "nand-disk",
+ .gpio = BALLOON3_GPIO_LED_NAND,
+ .active_low = 1,
+ },
+};
+
+static struct gpio_led_platform_data balloon3_gpio_leds_platform_data = {
+ .leds = balloon3_gpio_leds,
+ .num_leds = ARRAY_SIZE(balloon3_gpio_leds),
+};
+
+static struct platform_device balloon3led_device = {
+ .name = "leds-gpio",
+ .id = -1,
+ .dev = {
+ .platform_data = &balloon3_gpio_leds_platform_data,
+ },
+};
+
+static void __init balloon3_init(void)
+{
+ pr_info("Initialising Balloon3\n");
+
+ /* system bus arbiter setting
+ * - Core_Park
+ * - LCD_wt:DMA_wt:CORE_Wt = 2:3:4
+ */
+ ARB_CNTRL = ARB_CORE_PARK | 0x234;
+
+ pxa_set_i2c_info(NULL);
+ if (balloon3_has(BALLOON3_FEATURE_AUDIO))
+ pxa_set_ac97_info(NULL);
+
+ if (balloon3_has(BALLOON3_FEATURE_TOPPOLY)) {
+ pxa2xx_mfp_config(ARRAY_AND_SIZE(balloon3_lcd_pin_config));
+ gpio_request(BALLOON3_GPIO_RUN_BACKLIGHT,
+ "LCD Backlight Power");
+ gpio_direction_output(BALLOON3_GPIO_RUN_BACKLIGHT, 1);
+ set_pxa_fb_info(&balloon3_pxafb_info);
+ }
+
+ if (balloon3_has(BALLOON3_FEATURE_MMC)) {
+ pxa2xx_mfp_config(ARRAY_AND_SIZE(balloon3_mmc_pin_config));
+ pxa_set_mci_info(&balloon3_mci_platform_data);
+ }
+ pxa_set_ficp_info(&balloon3_ficp_platform_data);
+ if (balloon3_has(BALLOON3_FEATURE_OHCI)) {
+ pxa2xx_mfp_config(ARRAY_AND_SIZE(balloon3_ohci_pin_config));
+ pxa_set_ohci_info(&balloon3_ohci_platform_data);
+ }
+ pxa_set_udc_info(&balloon3_udc_info);
+
+ pxa2xx_mfp_config(ARRAY_AND_SIZE(balloon3_pin_config));
+
+ platform_device_register(&balloon3led_device);
+}
+
+static struct map_desc balloon3_io_desc[] __initdata = {
+ { /* CPLD/FPGA */
+ .virtual = BALLOON3_FPGA_VIRT,
+ .pfn = __phys_to_pfn(BALLOON3_FPGA_PHYS),
+ .length = BALLOON3_FPGA_LENGTH,
+ .type = MT_DEVICE,
+ },
+};
+
+static void __init balloon3_map_io(void)
+{
+ pxa_map_io();
+ iotable_init(balloon3_io_desc, ARRAY_SIZE(balloon3_io_desc));
+}
+
+MACHINE_START(BALLOON3, "Balloon3")
+ /* Maintainer: Nick Bane. */
+ .phys_io = 0x40000000,
+ .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc,
+ .map_io = balloon3_map_io,
+ .init_irq = balloon3_init_irq,
+ .timer = &pxa_timer,
+ .init_machine = balloon3_init,
+ .boot_params = PHYS_OFFSET + 0x100,
+MACHINE_END
unsigned int cken;
unsigned int delay;
unsigned int enabled;
- struct clk *other;
};
#define INIT_CLKREG(_clk,_devname,_conname) \
#include <linux/sysdev.h>
#include <linux/irq.h>
#include <linux/gpio.h>
+#include <linux/delay.h>
#include <linux/rtc-v3020.h>
#include <video/mbxfb.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/libertas_spi.h>
+
#include <mach/pxa27x.h>
#include <mach/ohci.h>
#include <mach/mmc.h>
+#include <mach/pxa2xx_spi.h>
#include "generic.h"
/* MMC power enable */
#define GPIO105_MMC_POWER (105)
+/* WLAN GPIOS */
+#define GPIO19_WLAN_STRAP (19)
+#define GPIO102_WLAN_RST (102)
+
static unsigned long cmx270_pin_config[] = {
/* AC'97 */
GPIO28_AC97_BITCLK,
GPIO26_SSP1_RXD,
/* SSP2 */
- GPIO19_SSP2_SCLK,
- GPIO14_SSP2_SFRM,
+ GPIO19_GPIO, /* SSP2 clock is used as GPIO for Libertas pin-strap */
+ GPIO14_GPIO,
GPIO87_SSP2_TXD,
GPIO88_SSP2_RXD,
GPIO0_GPIO | WAKEUP_ON_EDGE_BOTH,
GPIO105_GPIO | MFP_LPM_DRIVE_HIGH, /* MMC/SD power */
GPIO53_GPIO, /* PC card reset */
+ GPIO102_GPIO, /* WLAN reset */
/* NAND controls */
GPIO11_GPIO | MFP_LPM_DRIVE_HIGH, /* NAND CE# */
/* interrupts */
GPIO10_GPIO, /* DM9000 interrupt */
GPIO83_GPIO, /* MMC card detect */
+ GPIO95_GPIO, /* WLAN interrupt */
};
/* V3020 RTC */
#endif
#if defined(CONFIG_MMC) || defined(CONFIG_MMC_MODULE)
-static int cmx270_mci_init(struct device *dev,
- irq_handler_t cmx270_detect_int,
- void *data)
+static struct pxamci_platform_data cmx270_mci_platform_data = {
+ .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
+ .gpio_card_detect = GPIO83_MMC_IRQ,
+ .gpio_card_ro = -1,
+ .gpio_power = GPIO105_MMC_POWER,
+ .gpio_power_invert = 1,
+};
+
+static void __init cmx270_init_mmc(void)
{
- int err;
+ pxa_set_mci_info(&cmx270_mci_platform_data);
+}
+#else
+static inline void cmx270_init_mmc(void) {}
+#endif
+
+#if defined(CONFIG_SPI_PXA2XX) || defined(CONFIG_SPI_PXA2XX_MODULE)
+static struct pxa2xx_spi_master cm_x270_spi_info = {
+ .num_chipselect = 1,
+ .enable_dma = 1,
+};
+
+static struct pxa2xx_spi_chip cm_x270_libertas_chip = {
+ .rx_threshold = 1,
+ .tx_threshold = 1,
+ .timeout = 1000,
+ .gpio_cs = 14,
+};
+
+static unsigned long cm_x270_libertas_pin_config[] = {
+ /* SSP2 */
+ GPIO19_SSP2_SCLK,
+ GPIO14_GPIO,
+ GPIO87_SSP2_TXD,
+ GPIO88_SSP2_RXD,
+
+};
- err = gpio_request(GPIO105_MMC_POWER, "MMC/SD power");
- if (err) {
- dev_warn(dev, "power gpio unavailable\n");
+static int cm_x270_libertas_setup(struct spi_device *spi)
+{
+ int err = gpio_request(GPIO19_WLAN_STRAP, "WLAN STRAP");
+ if (err)
return err;
- }
- gpio_direction_output(GPIO105_MMC_POWER, 0);
+ err = gpio_request(GPIO102_WLAN_RST, "WLAN RST");
+ if (err)
+ goto err_free_strap;
- err = request_irq(CMX270_MMC_IRQ, cmx270_detect_int,
- IRQF_DISABLED | IRQF_TRIGGER_FALLING,
- "MMC card detect", data);
- if (err) {
- gpio_free(GPIO105_MMC_POWER);
- dev_err(dev, "cmx270_mci_init: MMC/SD: can't"
- " request MMC card detect IRQ\n");
- }
+ err = gpio_direction_output(GPIO102_WLAN_RST, 0);
+ if (err)
+ goto err_free_strap;
+ msleep(100);
+
+ err = gpio_direction_output(GPIO19_WLAN_STRAP, 1);
+ if (err)
+ goto err_free_strap;
+ msleep(100);
+
+ pxa2xx_mfp_config(ARRAY_AND_SIZE(cm_x270_libertas_pin_config));
+
+ gpio_set_value(GPIO102_WLAN_RST, 1);
+ msleep(100);
+
+ spi->bits_per_word = 16;
+ spi_setup(spi);
+
+ return 0;
+
+err_free_strap:
+ gpio_free(GPIO19_WLAN_STRAP);
return err;
}
-static void cmx270_mci_setpower(struct device *dev, unsigned int vdd)
+static int cm_x270_libertas_teardown(struct spi_device *spi)
{
- struct pxamci_platform_data *p_d = dev->platform_data;
-
- if ((1 << vdd) & p_d->ocr_mask) {
- dev_dbg(dev, "power on\n");
- gpio_set_value(GPIO105_MMC_POWER, 0);
- } else {
- gpio_set_value(GPIO105_MMC_POWER, 1);
- dev_dbg(dev, "power off\n");
- }
-}
+ gpio_set_value(GPIO102_WLAN_RST, 0);
+ gpio_free(GPIO102_WLAN_RST);
+ gpio_free(GPIO19_WLAN_STRAP);
-static void cmx270_mci_exit(struct device *dev, void *data)
-{
- free_irq(CMX270_MMC_IRQ, data);
- gpio_free(GPIO105_MMC_POWER);
+ return 0;
}
-static struct pxamci_platform_data cmx270_mci_platform_data = {
- .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
- .init = cmx270_mci_init,
- .setpower = cmx270_mci_setpower,
- .exit = cmx270_mci_exit,
+struct libertas_spi_platform_data cm_x270_libertas_pdata = {
+ .use_dummy_writes = 1,
+ .setup = cm_x270_libertas_setup,
+ .teardown = cm_x270_libertas_teardown,
};
-static void __init cmx270_init_mmc(void)
+static struct spi_board_info cm_x270_spi_devices[] __initdata = {
+ {
+ .modalias = "libertas_spi",
+ .max_speed_hz = 13000000,
+ .bus_num = 2,
+ .irq = gpio_to_irq(95),
+ .chip_select = 0,
+ .controller_data = &cm_x270_libertas_chip,
+ .platform_data = &cm_x270_libertas_pdata,
+ },
+};
+
+static void __init cmx270_init_spi(void)
{
- pxa_set_mci_info(&cmx270_mci_platform_data);
+ pxa2xx_set_spi_info(2, &cm_x270_spi_info);
+ spi_register_board_info(ARRAY_AND_SIZE(cm_x270_spi_devices));
}
#else
-static inline void cmx270_init_mmc(void) {}
+static inline void cmx270_init_spi(void) {}
#endif
void __init cmx270_init(void)
cmx270_init_mmc();
cmx270_init_ohci();
cmx270_init_2700G();
+ cmx270_init_spi();
}
}
static struct pxamci_platform_data cm_x300_mci_platform_data = {
- .detect_delay = 20,
- .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
- .init = cm_x300_mci_init,
- .exit = cm_x300_mci_exit,
+ .detect_delay = 20,
+ .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
+ .init = cm_x300_mci_init,
+ .exit = cm_x300_mci_exit,
+ .gpio_card_detect = -1,
+ .gpio_card_ro = -1,
+ .gpio_power = -1,
};
-static int cm_x300_mci2_ro(struct device *dev)
-{
- return gpio_get_value(GPIO85_MMC2_WP);
-}
-
-static int cm_x300_mci2_init(struct device *dev,
- irq_handler_t cm_x300_detect_int,
- void *data)
-{
- int err;
-
- /*
- * setup GPIO for CM-X300 MMC controller
- */
- err = gpio_request(GPIO82_MMC2_IRQ, "mmc card detect");
- if (err)
- goto err_request_cd;
- gpio_direction_input(GPIO82_MMC2_IRQ);
-
- err = gpio_request(GPIO85_MMC2_WP, "mmc write protect");
- if (err)
- goto err_request_wp;
- gpio_direction_input(GPIO85_MMC2_WP);
-
- err = request_irq(CM_X300_MMC2_IRQ, cm_x300_detect_int,
- IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
- "MMC card detect", data);
- if (err) {
- printk(KERN_ERR "%s: MMC/SD/SDIO: "
- "can't request card detect IRQ\n", __func__);
- goto err_request_irq;
- }
-
- return 0;
-
-err_request_irq:
- gpio_free(GPIO85_MMC2_WP);
-err_request_wp:
- gpio_free(GPIO82_MMC2_IRQ);
-err_request_cd:
- return err;
-}
-
-static void cm_x300_mci2_exit(struct device *dev, void *data)
-{
- free_irq(CM_X300_MMC2_IRQ, data);
- gpio_free(GPIO82_MMC2_IRQ);
- gpio_free(GPIO85_MMC2_WP);
-}
-
static struct pxamci_platform_data cm_x300_mci2_platform_data = {
- .detect_delay = 20,
- .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
- .init = cm_x300_mci2_init,
- .exit = cm_x300_mci2_exit,
- .get_ro = cm_x300_mci2_ro,
+ .detect_delay = 20,
+ .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
+ .gpio_card_detect = GPIO82_MMC2_IRQ,
+ .gpio_card_ro = GPIO85_MMC2_WP,
+ .gpio_power = -1,
};
static void __init cm_x300_init_mmc(void)
{
colibri_pxa300_init_eth();
colibri_pxa300_init_ohci();
+ colibri_pxa3xx_init_nand();
colibri_pxa300_init_lcd();
colibri_pxa3xx_init_lcd(mfp_to_gpio(GPIO39_GPIO));
colibri_pxa310_init_ac97();
static inline void colibri_pxa320_init_ac97(void) {}
#endif
+/*
+ * The following configuration is verified to work with the Toradex Orchid
+ * carrier board
+ */
+static mfp_cfg_t colibri_pxa320_uart_pin_config[] __initdata = {
+ /* UART 1 configuration (may be set by bootloader) */
+ GPIO99_UART1_CTS,
+ GPIO104_UART1_RTS,
+ GPIO97_UART1_RXD,
+ GPIO98_UART1_TXD,
+ GPIO101_UART1_DTR,
+ GPIO103_UART1_DSR,
+ GPIO100_UART1_DCD,
+ GPIO102_UART1_RI,
+
+ /* UART 2 configuration */
+ GPIO109_UART2_CTS,
+ GPIO112_UART2_RTS,
+ GPIO110_UART2_RXD,
+ GPIO111_UART2_TXD,
+
+ /* UART 3 configuration */
+ GPIO30_UART3_RXD,
+ GPIO31_UART3_TXD,
+};
+
+static void __init colibri_pxa320_init_uart(void)
+{
+ pxa3xx_mfp_config(ARRAY_AND_SIZE(colibri_pxa320_uart_pin_config));
+}
+
void __init colibri_pxa320_init(void)
{
colibri_pxa320_init_eth();
colibri_pxa320_init_ohci();
+ colibri_pxa3xx_init_nand();
colibri_pxa320_init_lcd();
colibri_pxa3xx_init_lcd(mfp_to_gpio(GPIO49_GPIO));
colibri_pxa320_init_ac97();
colibri_pxa3xx_init_mmc(ARRAY_AND_SIZE(colibri_pxa320_mmc_pin_config),
mfp_to_gpio(MFP_PIN_GPIO28));
+ colibri_pxa320_init_uart();
}
MACHINE_START(COLIBRI320, "Toradex Colibri PXA320")
#include <mach/colibri.h>
#include <mach/mmc.h>
#include <mach/pxafb.h>
+#include <mach/pxa3xx_nand.h>
#include "generic.h"
#include "devices.h"
}
static struct pxamci_platform_data colibri_pxa3xx_mci_platform_data = {
- .detect_delay = 20,
- .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
- .init = colibri_pxa3xx_mci_init,
- .exit = colibri_pxa3xx_mci_exit,
+ .detect_delay = 20,
+ .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
+ .init = colibri_pxa3xx_mci_init,
+ .exit = colibri_pxa3xx_mci_exit,
+ .gpio_card_detect = -1,
+ .gpio_card_ro = -1,
+ .gpio_power = -1,
};
void __init colibri_pxa3xx_init_mmc(mfp_cfg_t *pins, int len, int detect_pin)
}
#endif
+#if defined(CONFIG_MTD_NAND_PXA3xx) || defined(CONFIG_MTD_NAND_PXA3xx_MODULE)
+static struct mtd_partition colibri_nand_partitions[] = {
+ {
+ .name = "bootloader",
+ .offset = 0,
+ .size = SZ_512K,
+ .mask_flags = MTD_WRITEABLE, /* force read-only */
+ },
+ {
+ .name = "kernel",
+ .offset = MTDPART_OFS_APPEND,
+ .size = SZ_4M,
+ .mask_flags = MTD_WRITEABLE, /* force read-only */
+ },
+ {
+ .name = "reserved",
+ .offset = MTDPART_OFS_APPEND,
+ .size = SZ_1M,
+ .mask_flags = MTD_WRITEABLE, /* force read-only */
+ },
+ {
+ .name = "fs",
+ .offset = MTDPART_OFS_APPEND,
+ .size = MTDPART_SIZ_FULL,
+ },
+};
+
+static struct pxa3xx_nand_platform_data colibri_nand_info = {
+ .enable_arbiter = 1,
+ .keep_config = 1,
+ .parts = colibri_nand_partitions,
+ .nr_parts = ARRAY_SIZE(colibri_nand_partitions),
+};
+
+void __init colibri_pxa3xx_init_nand(void)
+{
+ pxa3xx_set_nand_info(&colibri_nand_info);
+}
+#endif
+
#include <linux/spi/ads7846.h>
#include <linux/spi/corgi_lcd.h>
#include <linux/mtd/sharpsl.h>
+#include <linux/input/matrix_keypad.h>
#include <video/w100fb.h>
#include <asm/setup.h>
GPIO6_MMC_CLK,
GPIO8_MMC_CS0,
+ /* GPIO Matrix Keypad */
+ GPIO66_GPIO, /* column 0 */
+ GPIO67_GPIO, /* column 1 */
+ GPIO68_GPIO, /* column 2 */
+ GPIO69_GPIO, /* column 3 */
+ GPIO70_GPIO, /* column 4 */
+ GPIO71_GPIO, /* column 5 */
+ GPIO72_GPIO, /* column 6 */
+ GPIO73_GPIO, /* column 7 */
+ GPIO74_GPIO, /* column 8 */
+ GPIO75_GPIO, /* column 9 */
+ GPIO76_GPIO, /* column 10 */
+ GPIO77_GPIO, /* column 11 */
+ GPIO58_GPIO, /* row 0 */
+ GPIO59_GPIO, /* row 1 */
+ GPIO60_GPIO, /* row 2 */
+ GPIO61_GPIO, /* row 3 */
+ GPIO62_GPIO, /* row 4 */
+ GPIO63_GPIO, /* row 5 */
+ GPIO64_GPIO, /* row 6 */
+ GPIO65_GPIO, /* row 7 */
+
/* GPIO */
GPIO9_GPIO, /* CORGI_GPIO_nSD_DETECT */
GPIO7_GPIO, /* CORGI_GPIO_nSD_WP */
/*
* Corgi Keyboard Device
*/
+#define CORGI_KEY_CALENDER KEY_F1
+#define CORGI_KEY_ADDRESS KEY_F2
+#define CORGI_KEY_FN KEY_F3
+#define CORGI_KEY_CANCEL KEY_F4
+#define CORGI_KEY_OFF KEY_SUSPEND
+#define CORGI_KEY_EXOK KEY_F5
+#define CORGI_KEY_EXCANCEL KEY_F6
+#define CORGI_KEY_EXJOGDOWN KEY_F7
+#define CORGI_KEY_EXJOGUP KEY_F8
+#define CORGI_KEY_JAP1 KEY_LEFTCTRL
+#define CORGI_KEY_JAP2 KEY_LEFTALT
+#define CORGI_KEY_MAIL KEY_F10
+#define CORGI_KEY_OK KEY_F11
+#define CORGI_KEY_MENU KEY_F12
+
+static const uint32_t corgikbd_keymap[] = {
+ KEY(0, 1, KEY_1),
+ KEY(0, 2, KEY_3),
+ KEY(0, 3, KEY_5),
+ KEY(0, 4, KEY_6),
+ KEY(0, 5, KEY_7),
+ KEY(0, 6, KEY_9),
+ KEY(0, 7, KEY_0),
+ KEY(0, 8, KEY_BACKSPACE),
+ KEY(1, 1, KEY_2),
+ KEY(1, 2, KEY_4),
+ KEY(1, 3, KEY_R),
+ KEY(1, 4, KEY_Y),
+ KEY(1, 5, KEY_8),
+ KEY(1, 6, KEY_I),
+ KEY(1, 7, KEY_O),
+ KEY(1, 8, KEY_P),
+ KEY(2, 0, KEY_TAB),
+ KEY(2, 1, KEY_Q),
+ KEY(2, 2, KEY_E),
+ KEY(2, 3, KEY_T),
+ KEY(2, 4, KEY_G),
+ KEY(2, 5, KEY_U),
+ KEY(2, 6, KEY_J),
+ KEY(2, 7, KEY_K),
+ KEY(3, 0, CORGI_KEY_CALENDER),
+ KEY(3, 1, KEY_W),
+ KEY(3, 2, KEY_S),
+ KEY(3, 3, KEY_F),
+ KEY(3, 4, KEY_V),
+ KEY(3, 5, KEY_H),
+ KEY(3, 6, KEY_M),
+ KEY(3, 7, KEY_L),
+ KEY(3, 9, KEY_RIGHTSHIFT),
+ KEY(4, 0, CORGI_KEY_ADDRESS),
+ KEY(4, 1, KEY_A),
+ KEY(4, 2, KEY_D),
+ KEY(4, 3, KEY_C),
+ KEY(4, 4, KEY_B),
+ KEY(4, 5, KEY_N),
+ KEY(4, 6, KEY_DOT),
+ KEY(4, 8, KEY_ENTER),
+ KEY(4, 10, KEY_LEFTSHIFT),
+ KEY(5, 0, CORGI_KEY_MAIL),
+ KEY(5, 1, KEY_Z),
+ KEY(5, 2, KEY_X),
+ KEY(5, 3, KEY_MINUS),
+ KEY(5, 4, KEY_SPACE),
+ KEY(5, 5, KEY_COMMA),
+ KEY(5, 7, KEY_UP),
+ KEY(5, 11, CORGI_KEY_FN),
+ KEY(6, 0, KEY_SYSRQ),
+ KEY(6, 1, CORGI_KEY_JAP1),
+ KEY(6, 2, CORGI_KEY_JAP2),
+ KEY(6, 3, CORGI_KEY_CANCEL),
+ KEY(6, 4, CORGI_KEY_OK),
+ KEY(6, 5, CORGI_KEY_MENU),
+ KEY(6, 6, KEY_LEFT),
+ KEY(6, 7, KEY_DOWN),
+ KEY(6, 8, KEY_RIGHT),
+ KEY(7, 0, CORGI_KEY_OFF),
+ KEY(7, 1, CORGI_KEY_EXOK),
+ KEY(7, 2, CORGI_KEY_EXCANCEL),
+ KEY(7, 3, CORGI_KEY_EXJOGDOWN),
+ KEY(7, 4, CORGI_KEY_EXJOGUP),
+};
+
+static struct matrix_keymap_data corgikbd_keymap_data = {
+ .keymap = corgikbd_keymap,
+ .keymap_size = ARRAY_SIZE(corgikbd_keymap),
+};
+
+static const int corgikbd_row_gpios[] =
+ { 58, 59, 60, 61, 62, 63, 64, 65 };
+static const int corgikbd_col_gpios[] =
+ { 66, 67, 68, 69, 70, 71, 72, 73, 74, 75, 76, 77 };
+
+static struct matrix_keypad_platform_data corgikbd_pdata = {
+ .keymap_data = &corgikbd_keymap_data,
+ .row_gpios = corgikbd_row_gpios,
+ .col_gpios = corgikbd_col_gpios,
+ .num_row_gpios = ARRAY_SIZE(corgikbd_row_gpios),
+ .num_col_gpios = ARRAY_SIZE(corgikbd_col_gpios),
+ .col_scan_delay_us = 10,
+ .debounce_ms = 10,
+ .wakeup = 1,
+};
+
static struct platform_device corgikbd_device = {
- .name = "corgi-keyboard",
+ .name = "matrix-keypad",
.id = -1,
+ .dev = {
+ .platform_data = &corgikbd_pdata,
+ },
};
/*
* The card detect interrupt isn't debounced so we delay it by 250ms
* to give the card a chance to fully insert/eject.
*/
-static struct pxamci_platform_data corgi_mci_platform_data;
-
-static int corgi_mci_init(struct device *dev, irq_handler_t corgi_detect_int, void *data)
-{
- int err;
-
- err = gpio_request(CORGI_GPIO_nSD_DETECT, "nSD_DETECT");
- if (err)
- goto err_out;
-
- err = gpio_request(CORGI_GPIO_nSD_WP, "nSD_WP");
- if (err)
- goto err_free_1;
-
- err = gpio_request(CORGI_GPIO_SD_PWR, "SD_PWR");
- if (err)
- goto err_free_2;
-
- gpio_direction_input(CORGI_GPIO_nSD_DETECT);
- gpio_direction_input(CORGI_GPIO_nSD_WP);
- gpio_direction_output(CORGI_GPIO_SD_PWR, 0);
-
- corgi_mci_platform_data.detect_delay = msecs_to_jiffies(250);
-
- err = request_irq(CORGI_IRQ_GPIO_nSD_DETECT, corgi_detect_int,
- IRQF_DISABLED | IRQF_TRIGGER_RISING |
- IRQF_TRIGGER_FALLING,
- "MMC card detect", data);
- if (err) {
- pr_err("%s: MMC/SD: can't request MMC card detect IRQ\n",
- __func__);
- goto err_free_3;
- }
- return 0;
-
-err_free_3:
- gpio_free(CORGI_GPIO_SD_PWR);
-err_free_2:
- gpio_free(CORGI_GPIO_nSD_WP);
-err_free_1:
- gpio_free(CORGI_GPIO_nSD_DETECT);
-err_out:
- return err;
-}
-
-static void corgi_mci_setpower(struct device *dev, unsigned int vdd)
-{
- struct pxamci_platform_data* p_d = dev->platform_data;
-
- gpio_set_value(CORGI_GPIO_SD_PWR, ((1 << vdd) & p_d->ocr_mask));
-}
-
-static int corgi_mci_get_ro(struct device *dev)
-{
- return gpio_get_value(CORGI_GPIO_nSD_WP);
-}
-
-static void corgi_mci_exit(struct device *dev, void *data)
-{
- free_irq(CORGI_IRQ_GPIO_nSD_DETECT, data);
- gpio_free(CORGI_GPIO_SD_PWR);
- gpio_free(CORGI_GPIO_nSD_WP);
- gpio_free(CORGI_GPIO_nSD_DETECT);
-}
-
static struct pxamci_platform_data corgi_mci_platform_data = {
- .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
- .init = corgi_mci_init,
- .get_ro = corgi_mci_get_ro,
- .setpower = corgi_mci_setpower,
- .exit = corgi_mci_exit,
+ .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
+ .gpio_card_detect = -1,
+ .gpio_card_ro = CORGI_GPIO_nSD_WP,
+ .gpio_power = CORGI_GPIO_SD_PWR,
};
/*
* Irda
*/
-static void corgi_irda_transceiver_mode(struct device *dev, int mode)
-{
- gpio_set_value(CORGI_GPIO_IR_ON, mode & IR_OFF);
- pxa2xx_transceiver_mode(dev, mode);
-}
-
-static int corgi_irda_startup(struct device *dev)
-{
- int err;
-
- err = gpio_request(CORGI_GPIO_IR_ON, "IR_ON");
- if (err)
- return err;
-
- gpio_direction_output(CORGI_GPIO_IR_ON, 1);
- return 0;
-}
-
-static void corgi_irda_shutdown(struct device *dev)
-{
- gpio_free(CORGI_GPIO_IR_ON);
-}
-
static struct pxaficp_platform_data corgi_ficp_platform_data = {
+ .gpio_pwdown = CORGI_GPIO_IR_ON,
.transceiver_cap = IR_SIRMODE | IR_OFF,
- .transceiver_mode = corgi_irda_transceiver_mode,
- .startup = corgi_irda_startup,
- .shutdown = corgi_irda_shutdown,
};
corgi_init_spi();
pxa_set_udc_info(&udc_info);
+ corgi_mci_platform_data.detect_delay = msecs_to_jiffies(250);
pxa_set_mci_info(&corgi_mci_platform_data);
pxa_set_ficp_info(&corgi_ficp_platform_data);
pxa_set_i2c_info(NULL);
static int csb726_mci_init(struct device *dev,
irq_handler_t detect, void *data)
{
- int err;
-
csb726_mci_data.detect_delay = msecs_to_jiffies(500);
-
- err = gpio_request(CSB726_GPIO_MMC_DETECT, "MMC detect");
- if (err)
- goto err_det_req;
-
- err = gpio_direction_input(CSB726_GPIO_MMC_DETECT);
- if (err)
- goto err_det_dir;
-
- err = gpio_request(CSB726_GPIO_MMC_RO, "MMC ro");
- if (err)
- goto err_ro_req;
-
- err = gpio_direction_input(CSB726_GPIO_MMC_RO);
- if (err)
- goto err_ro_dir;
-
- err = request_irq(gpio_to_irq(CSB726_GPIO_MMC_DETECT), detect,
- IRQF_DISABLED, "MMC card detect", data);
- if (err)
- goto err_irq;
-
return 0;
-
-err_irq:
-err_ro_dir:
- gpio_free(CSB726_GPIO_MMC_RO);
-err_ro_req:
-err_det_dir:
- gpio_free(CSB726_GPIO_MMC_DETECT);
-err_det_req:
- return err;
-}
-
-static int csb726_mci_get_ro(struct device *dev)
-{
- return gpio_get_value(CSB726_GPIO_MMC_RO);
-}
-
-static void csb726_mci_exit(struct device *dev, void *data)
-{
- free_irq(gpio_to_irq(CSB726_GPIO_MMC_DETECT), data);
- gpio_free(CSB726_GPIO_MMC_RO);
- gpio_free(CSB726_GPIO_MMC_DETECT);
}
static struct pxamci_platform_data csb726_mci = {
- .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
- .init = csb726_mci_init,
- .get_ro = csb726_mci_get_ro,
+ .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
+ .init = csb726_mci_init,
/* FIXME setpower */
- .exit = csb726_mci_exit,
+ .gpio_card_detect = CSB726_GPIO_MMC_DETECT,
+ .gpio_card_ro = CSB726_GPIO_MMC_RO,
+ .gpio_power = -1,
};
static struct pxaohci_platform_data csb726_ohci_platform_data = {
{
pxa_register_device(&pxa3xx_device_nand, info);
}
+
+static struct resource pxa3xx_resources_gcu[] = {
+ {
+ .start = 0x54000000,
+ .end = 0x54000fff,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = IRQ_GCU,
+ .end = IRQ_GCU,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static u64 pxa3xx_gcu_dmamask = DMA_BIT_MASK(32);
+
+struct platform_device pxa3xx_device_gcu = {
+ .name = "pxa3xx-gcu",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(pxa3xx_resources_gcu),
+ .resource = pxa3xx_resources_gcu,
+ .dev = {
+ .dma_mask = &pxa3xx_gcu_dmamask,
+ .coherent_dma_mask = 0xffffffff,
+ },
+};
+
#endif /* CONFIG_PXA3xx */
/* pxa2xx-spi platform-device ID equals respective SSP platform-device ID + 1.
extern struct platform_device pxa3xx_device_nand;
extern struct platform_device pxa3xx_device_i2c_power;
+extern struct platform_device pxa3xx_device_gcu;
+
void __init pxa_register_device(struct platform_device *dev, void *data);
platform_add_devices(devices, ARRAY_SIZE(devices));
pxa_set_udc_info(&e7xx_udc_mach_info);
pxa_set_ac97_info(NULL);
- e7xx_irda_init();
pxa_set_ficp_info(&e7xx_ficp_platform_data);
}
platform_add_devices(devices, ARRAY_SIZE(devices));
pxa_set_udc_info(&e7xx_udc_mach_info);
pxa_set_ac97_info(NULL);
- e7xx_irda_init();
pxa_set_ficp_info(&e7xx_ficp_platform_data);
}
}
static struct pxamci_platform_data em_x270_mci_platform_data = {
- .ocr_mask = MMC_VDD_20_21|MMC_VDD_21_22|MMC_VDD_22_23|
- MMC_VDD_24_25|MMC_VDD_25_26|MMC_VDD_26_27|
- MMC_VDD_27_28|MMC_VDD_28_29|MMC_VDD_29_30|
- MMC_VDD_30_31|MMC_VDD_31_32,
- .init = em_x270_mci_init,
- .setpower = em_x270_mci_setpower,
- .exit = em_x270_mci_exit,
+ .ocr_mask = MMC_VDD_20_21|MMC_VDD_21_22|MMC_VDD_22_23|
+ MMC_VDD_24_25|MMC_VDD_25_26|MMC_VDD_26_27|
+ MMC_VDD_27_28|MMC_VDD_28_29|MMC_VDD_29_30|
+ MMC_VDD_30_31|MMC_VDD_31_32,
+ .init = em_x270_mci_init,
+ .setpower = em_x270_mci_setpower,
+ .exit = em_x270_mci_exit,
+ .gpio_card_detect = -1,
+ .gpio_card_ro = -1,
+ .gpio_power = -1,
};
static void __init em_x270_init_mmc(void)
return 0;
}
-static struct soc_camera_link iclink = {
- .bus_id = 0,
- .power = em_x270_sensor_power,
-};
-
static struct i2c_board_info em_x270_i2c_cam_info[] = {
{
I2C_BOARD_INFO("mt9m111", 0x48),
+ },
+};
+
+static struct soc_camera_link iclink = {
+ .bus_id = 0,
+ .power = em_x270_sensor_power,
+ .board_info = &em_x270_i2c_cam_info[0],
+ .i2c_adapter_id = 0,
+ .module_name = "mt9m111",
+};
+
+static struct platform_device em_x270_camera = {
+ .name = "soc-camera-pdrv",
+ .id = -1,
+ .dev = {
.platform_data = &iclink,
},
};
static void __init em_x270_init_camera(void)
{
- i2c_register_board_info(0, ARRAY_AND_SIZE(em_x270_i2c_cam_info));
pxa_set_camera_info(&em_x270_camera_platform_data);
+ platform_device_register(&em_x270_camera);
}
#else
static inline void em_x270_init_camera(void) {}
REGULATOR_CONSUMER(ldo10, &pxa_device_mci.dev, "vcc sdio");
REGULATOR_CONSUMER(ldo12, NULL, "vcc usb");
REGULATOR_CONSUMER(ldo19, &em_x270_gprs_userspace_consumer.dev, "vcc gprs");
+REGULATOR_CONSUMER(buck2, NULL, "vcc_core");
#define REGULATOR_INIT(_ldo, _min_uV, _max_uV, _ops_mask) \
static struct regulator_init_data _ldo##_data = { \
REGULATOR_CHANGE_STATUS | REGULATOR_CHANGE_VOLTAGE);
REGULATOR_INIT(ldo12, 3000000, 3000000, REGULATOR_CHANGE_STATUS);
REGULATOR_INIT(ldo19, 3200000, 3200000, REGULATOR_CHANGE_STATUS);
+REGULATOR_INIT(buck2, 1000000, 1650000, REGULATOR_CHANGE_VOLTAGE);
struct led_info em_x270_led_info = {
.name = "em-x270:orange",
DA9030_LDO(12),
DA9030_LDO(19),
+ DA9030_SUBDEV(regulator, BUCK2, &buck2_data),
+
DA9030_SUBDEV(led, LED_PC, &em_x270_led_info),
DA9030_SUBDEV(backlight, WLED, &em_x270_led_info),
DA9030_SUBDEV(battery, BAT, &em_x270_batterty_info),
static void __init em_x270_module_init(void)
{
- pr_info("%s\n", __func__);
pxa2xx_mfp_config(ARRAY_AND_SIZE(em_x270_pin_config));
mmc_cd = GPIO13_MMC_CD;
static void __init em_x270_exeda_init(void)
{
- pr_info("%s\n", __func__);
pxa2xx_mfp_config(ARRAY_AND_SIZE(exeda_pin_config));
mmc_cd = GPIO114_MMC_CD;
.gpio_pullup_inverted = 1
};
-static void e7xx_irda_transceiver_mode(struct device *dev, int mode)
-{
- if (mode & IR_OFF) {
- gpio_set_value(GPIO_E7XX_IR_OFF, 1);
- pxa2xx_transceiver_mode(dev, mode);
- } else {
- pxa2xx_transceiver_mode(dev, mode);
- gpio_set_value(GPIO_E7XX_IR_OFF, 0);
- }
-}
-
-int e7xx_irda_init(void)
-{
- int ret;
-
- ret = gpio_request(GPIO_E7XX_IR_OFF, "IrDA power");
- if (ret)
- goto out;
-
- ret = gpio_direction_output(GPIO_E7XX_IR_OFF, 0);
- if (ret)
- goto out;
-
- e7xx_irda_transceiver_mode(NULL, IR_SIRMODE | IR_OFF);
-out:
- return ret;
-}
-
-static void e7xx_irda_shutdown(struct device *dev)
-{
- e7xx_irda_transceiver_mode(dev, IR_SIRMODE | IR_OFF);
- gpio_free(GPIO_E7XX_IR_OFF);
-}
-
struct pxaficp_platform_data e7xx_ficp_platform_data = {
- .transceiver_cap = IR_SIRMODE | IR_OFF,
- .transceiver_mode = e7xx_irda_transceiver_mode,
- .shutdown = e7xx_irda_shutdown,
+ .gpio_pwdown = GPIO_E7XX_IR_OFF,
+ .transceiver_cap = IR_SIRMODE | IR_OFF,
};
int eseries_tmio_enable(struct platform_device *dev)
#ifdef CONFIG_MMC_PXA
static struct pxamci_platform_data gumstix_mci_platform_data = {
- .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
+ .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
+ .gpio_card_detect = -1,
+ .gpio_card_ro = -1,
+ .gpio_power = -1,
};
static void __init gumstix_mmc_init(void)
#include <mach/irda.h>
#include <mach/pxa2xx_spi.h>
+#include <video/platform_lcd.h>
#include <video/w100fb.h>
#include "devices.h"
* IRDA
*/
-static void irda_transceiver_mode(struct device *dev, int mode)
-{
- gpio_set_value(GPIO105_HX4700_nIR_ON, mode & IR_OFF);
-}
-
static struct pxaficp_platform_data ficp_info = {
- .transceiver_cap = IR_SIRMODE | IR_OFF,
- .transceiver_mode = irda_transceiver_mode,
+ .gpio_pwdown = GPIO105_HX4700_nIR_ON,
+ .transceiver_cap = IR_SIRMODE | IR_OFF,
};
/*
* LCD - Sony display connected to ATI Imageon w3220
*/
-static int lcd_power;
-
static void sony_lcd_init(void)
{
gpio_set_value(GPIO84_HX4700_LCD_SQN, 1);
gpio_set_value(GPIO110_HX4700_LCD_LVDD_3V3_ON, 0);
}
-static int hx4700_lcd_set_power(struct lcd_device *ldev, int level)
-{
- switch (level) {
- case FB_BLANK_UNBLANK:
- sony_lcd_init();
- break;
- case FB_BLANK_NORMAL:
- case FB_BLANK_VSYNC_SUSPEND:
- case FB_BLANK_HSYNC_SUSPEND:
- case FB_BLANK_POWERDOWN:
- sony_lcd_off();
- break;
- }
- lcd_power = level;
- return 0;
-}
-
-static int hx4700_lcd_get_power(struct lcd_device *lm)
-{
- return lcd_power;
-}
-
-static struct lcd_ops hx4700_lcd_ops = {
- .get_power = hx4700_lcd_get_power,
- .set_power = hx4700_lcd_set_power,
-};
-
-static struct lcd_device *hx4700_lcd_device;
-
#ifdef CONFIG_PM
static void w3220_lcd_suspend(struct w100fb_par *wfb)
{
.resource = w3220_resources,
};
+static void hx4700_lcd_set_power(struct plat_lcd_data *pd, unsigned int power)
+{
+ if (power)
+ sony_lcd_init();
+ else
+ sony_lcd_off();
+}
+
+static struct plat_lcd_data hx4700_lcd_data = {
+ .set_power = hx4700_lcd_set_power,
+};
+
+static struct platform_device hx4700_lcd = {
+ .name = "platform-lcd",
+ .id = -1,
+ .dev = {
+ .platform_data = &hx4700_lcd_data,
+ .parent = &w3220.dev,
+ },
+};
+
/*
* Backlight
*/
pxa2xx_set_spi_info(2, &pxa_ssp2_master_info);
spi_register_board_info(ARRAY_AND_SIZE(tsc2046_board_info));
- hx4700_lcd_device = lcd_device_register("w100fb", NULL,
- (void *)&w3220_info, &hx4700_lcd_ops);
-
gpio_set_value(GPIO71_HX4700_ASIC3_nRESET, 0);
mdelay(10);
gpio_set_value(GPIO71_HX4700_ASIC3_nRESET, 1);
};
static struct pxamci_platform_data idp_mci_platform_data = {
- .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
+ .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
+ .gpio_card_detect = -1,
+ .gpio_card_ro = -1,
+ .gpio_power = -1,
};
static void __init idp_init(void)
static struct pxamci_platform_data imote2_mci_platform_data = {
.ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34, /* default anyway */
.get_ro = imote2_mci_get_ro,
+ .gpio_card_detect = -1,
+ .gpio_card_ro = -1,
+ .gpio_power = -1,
};
static struct mtd_partition imote2flash_partitions[] = {
--- /dev/null
+/*
+ * linux/include/asm-arm/arch-pxa/balloon3.h
+ *
+ * Authors: Nick Bane and Wookey
+ * Created: Oct, 2005
+ * Copyright: Toby Churchill Ltd
+ * Cribbed from mainstone.c, by Nicholas Pitre
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef ASM_ARCH_BALLOON3_H
+#define ASM_ARCH_BALLOON3_H
+
+enum balloon3_features {
+ BALLOON3_FEATURE_OHCI,
+ BALLOON3_FEATURE_MMC,
+ BALLOON3_FEATURE_CF,
+ BALLOON3_FEATURE_AUDIO,
+ BALLOON3_FEATURE_TOPPOLY,
+};
+
+#define BALLOON3_FPGA_PHYS PXA_CS4_PHYS
+#define BALLOON3_FPGA_VIRT (0xf1000000) /* as per balloon2 */
+#define BALLOON3_FPGA_LENGTH 0x01000000
+
+/* FPGA/CPLD registers */
+#define BALLOON3_PCMCIA0_REG (BALLOON3_FPGA_VIRT + 0x00e00008)
+/* fixme - same for now */
+#define BALLOON3_PCMCIA1_REG (BALLOON3_FPGA_VIRT + 0x00e00008)
+#define BALLOON3_NANDIO_IO_REG (BALLOON3_FPGA_VIRT + 0x00e00000)
+/* fpga/cpld interrupt control register */
+#define BALLOON3_INT_CONTROL_REG (BALLOON3_FPGA_VIRT + 0x00e0000C)
+#define BALLOON3_NANDIO_CTL2_REG (BALLOON3_FPGA_VIRT + 0x00e00010)
+#define BALLOON3_NANDIO_CTL_REG (BALLOON3_FPGA_VIRT + 0x00e00014)
+#define BALLOON3_VERSION_REG (BALLOON3_FPGA_VIRT + 0x00e0001c)
+
+#define BALLOON3_SAMOSA_ADDR_REG (BALLOON3_FPGA_VIRT + 0x00c00000)
+#define BALLOON3_SAMOSA_DATA_REG (BALLOON3_FPGA_VIRT + 0x00c00004)
+#define BALLOON3_SAMOSA_STATUS_REG (BALLOON3_FPGA_VIRT + 0x00c0001c)
+
+/* GPIOs for irqs */
+#define BALLOON3_GPIO_AUX_NIRQ (94)
+#define BALLOON3_GPIO_CODEC_IRQ (95)
+
+/* Timer and Idle LED locations */
+#define BALLOON3_GPIO_LED_NAND (9)
+#define BALLOON3_GPIO_LED_IDLE (10)
+
+/* backlight control */
+#define BALLOON3_GPIO_RUN_BACKLIGHT (99)
+
+#define BALLOON3_GPIO_S0_CD (105)
+
+/* FPGA Interrupt Mask/Acknowledge Register */
+#define BALLOON3_INT_S0_IRQ (1 << 0) /* PCMCIA 0 IRQ */
+#define BALLOON3_INT_S0_STSCHG (1 << 1) /* PCMCIA 0 status changed */
+
+/* CF Status Register */
+#define BALLOON3_PCMCIA_nIRQ (1 << 0) /* IRQ / ready signal */
+#define BALLOON3_PCMCIA_nSTSCHG_BVD1 (1 << 1)
+ /* VDD sense / card status changed */
+
+/* CF control register (write) */
+#define BALLOON3_PCMCIA_RESET (1 << 0) /* Card reset signal */
+#define BALLOON3_PCMCIA_ENABLE (1 << 1)
+#define BALLOON3_PCMCIA_ADD_ENABLE (1 << 2)
+
+/* CPLD (and FPGA) interface definitions */
+#define CPLD_LCD0_DATA_SET 0x00
+#define CPLD_LCD0_DATA_CLR 0x10
+#define CPLD_LCD0_COMMAND_SET 0x01
+#define CPLD_LCD0_COMMAND_CLR 0x11
+#define CPLD_LCD1_DATA_SET 0x02
+#define CPLD_LCD1_DATA_CLR 0x12
+#define CPLD_LCD1_COMMAND_SET 0x03
+#define CPLD_LCD1_COMMAND_CLR 0x13
+
+#define CPLD_MISC_SET 0x07
+#define CPLD_MISC_CLR 0x17
+#define CPLD_MISC_LOON_NRESET_BIT 0
+#define CPLD_MISC_LOON_UNSUSP_BIT 1
+#define CPLD_MISC_RUN_5V_BIT 2
+#define CPLD_MISC_CHG_D0_BIT 3
+#define CPLD_MISC_CHG_D1_BIT 4
+#define CPLD_MISC_DAC_NCS_BIT 5
+
+#define CPLD_LCD_SET 0x08
+#define CPLD_LCD_CLR 0x18
+#define CPLD_LCD_BACKLIGHT_EN_0_BIT 0
+#define CPLD_LCD_BACKLIGHT_EN_1_BIT 1
+#define CPLD_LCD_LED_RED_BIT 4
+#define CPLD_LCD_LED_GREEN_BIT 5
+#define CPLD_LCD_NRESET_BIT 7
+
+#define CPLD_LCD_RO_SET 0x09
+#define CPLD_LCD_RO_CLR 0x19
+#define CPLD_LCD_RO_LCD0_nWAIT_BIT 0
+#define CPLD_LCD_RO_LCD1_nWAIT_BIT 1
+
+#define CPLD_SERIAL_SET 0x0a
+#define CPLD_SERIAL_CLR 0x1a
+#define CPLD_SERIAL_GSM_RI_BIT 0
+#define CPLD_SERIAL_GSM_CTS_BIT 1
+#define CPLD_SERIAL_GSM_DTR_BIT 2
+#define CPLD_SERIAL_LPR_CTS_BIT 3
+#define CPLD_SERIAL_TC232_CTS_BIT 4
+#define CPLD_SERIAL_TC232_DSR_BIT 5
+
+#define CPLD_SROUTING_SET 0x0b
+#define CPLD_SROUTING_CLR 0x1b
+#define CPLD_SROUTING_MSP430_LPR 0
+#define CPLD_SROUTING_MSP430_TC232 1
+#define CPLD_SROUTING_MSP430_GSM 2
+#define CPLD_SROUTING_LOON_LPR (0 << 4)
+#define CPLD_SROUTING_LOON_TC232 (1 << 4)
+#define CPLD_SROUTING_LOON_GSM (2 << 4)
+
+#define CPLD_AROUTING_SET 0x0c
+#define CPLD_AROUTING_CLR 0x1c
+#define CPLD_AROUTING_MIC2PHONE_BIT 0
+#define CPLD_AROUTING_PHONE2INT_BIT 1
+#define CPLD_AROUTING_PHONE2EXT_BIT 2
+#define CPLD_AROUTING_LOONL2INT_BIT 3
+#define CPLD_AROUTING_LOONL2EXT_BIT 4
+#define CPLD_AROUTING_LOONR2PHONE_BIT 5
+#define CPLD_AROUTING_LOONR2INT_BIT 6
+#define CPLD_AROUTING_LOONR2EXT_BIT 7
+
+extern int balloon3_has(enum balloon3_features feature);
+
+#endif
extern void colibri_pxa3xx_init_eth(struct ax_plat_data *plat_data);
#endif
+#if defined(CONFIG_MTD_NAND_PXA3xx) || defined(CONFIG_MTD_NAND_PXA3xx_MODULE)
+extern void colibri_pxa3xx_init_nand(void);
+#else
+static inline void colibri_pxa3xx_init_nand(void) {}
+#endif
+
/* physical memory regions */
#define COLIBRI_SDRAM_BASE 0xa0000000 /* SDRAM region */
mov \tmp, \tmp, lsr #13
and \tmp, \tmp, #0x7 @ Core G
cmp \tmp, #1
- bhi 1004f
+ bhi 1002f
+ @ Core Generation 1 (PXA25x)
mov \base, #io_p2v(0x40000000) @ IIR Ctl = 0x40d00000
add \base, \base, #0x00d00000
ldr \irqstat, [\base, #0] @ ICIP
ldr \irqnr, [\base, #4] @ ICMR
- b 1002f
-1004:
- mrc p6, 0, \irqstat, c6, c0, 0 @ ICIP2
- mrc p6, 0, \irqnr, c7, c0, 0 @ ICMR2
ands \irqnr, \irqstat, \irqnr
- beq 1003f
+ beq 1001f
rsb \irqstat, \irqnr, #0
and \irqstat, \irqstat, \irqnr
clz \irqnr, \irqstat
- rsb \irqnr, \irqnr, #31
- add \irqnr, \irqnr, #(32 + PXA_IRQ(0))
+ rsb \irqnr, \irqnr, #(31 + PXA_IRQ(0))
b 1001f
-1003:
- mrc p6, 0, \irqstat, c0, c0, 0 @ ICIP
- mrc p6, 0, \irqnr, c1, c0, 0 @ ICMR
1002:
- ands \irqnr, \irqstat, \irqnr
+ @ Core Generation 2 (PXA27x) or Core Generation 3 (PXA3xx)
+ mrc p6, 0, \irqstat, c5, c0, 0 @ ICHP
+ tst \irqstat, #0x80000000
beq 1001f
- rsb \irqstat, \irqnr, #0
- and \irqstat, \irqstat, \irqnr
- clz \irqnr, \irqstat
- rsb \irqnr, \irqnr, #(31 + PXA_IRQ(0))
+ bic \irqstat, \irqstat, #0x80000000
+ mov \irqnr, \irqstat, lsr #16
1001:
.endm
#define __cpu_is_pxa935(id) (0)
#endif
+#ifdef CONFIG_CPU_PXA950
+#define __cpu_is_pxa950(id) \
+ ({ \
+ unsigned int _id = (id) >> 4 & 0xfff; \
+ id == 0x697; \
+ })
+#else
+#define __cpu_is_pxa950(id) (0)
+#endif
+
#define cpu_is_pxa210() \
({ \
__cpu_is_pxa210(read_cpuid_id()); \
__cpu_is_pxa935(id); \
})
+#define cpu_is_pxa950() \
+ ({ \
+ unsigned int id = read_cpuid(CPUID_ID); \
+ __cpu_is_pxa950(id); \
+ })
+
+
/*
* CPUID Core Generation Bit
* <= 0x2 for pxa21x/pxa25x/pxa26x/pxa27x
void (*transceiver_mode)(struct device *dev, int mode);
int (*startup)(struct device *dev);
void (*shutdown)(struct device *dev);
+ int gpio_pwdown; /* powerdown GPIO for the IrDA chip */
+ bool gpio_pwdown_inverted; /* gpio_pwdown is inverted */
};
extern void pxa_set_ficp_info(struct pxaficp_platform_data *info);
#ifdef CONFIG_PXA3xx
#define IRQ_SSP4 PXA_IRQ(13) /* SSP4 service request */
#define IRQ_CIR PXA_IRQ(34) /* Consumer IR */
+#define IRQ_COMM_WDT PXA_IRQ(35) /* Comm WDT interrupt */
#define IRQ_TSI PXA_IRQ(36) /* Touch Screen Interface (PXA320) */
#define IRQ_USIM2 PXA_IRQ(38) /* USIM2 Controller */
-#define IRQ_GRPHICS PXA_IRQ(39) /* Graphics Controller */
+#define IRQ_GCU PXA_IRQ(39) /* Graphics Controller */
#define IRQ_MMC2 PXA_IRQ(41) /* MMC2 Controller */
#define IRQ_1WIRE PXA_IRQ(44) /* 1-Wire Controller */
#define IRQ_NAND PXA_IRQ(45) /* NAND Controller */
#define IRQ_MMC3 PXA_IRQ(55) /* MMC3 Controller (PXA310) */
#endif
-#define PXA_GPIO_IRQ_BASE PXA_IRQ(64)
-#define PXA_GPIO_IRQ_NUM (128)
+#ifdef CONFIG_CPU_PXA935
+#define IRQ_U2O PXA_IRQ(64) /* USB OTG 2.0 Controller (PXA935) */
+#define IRQ_U2H PXA_IRQ(65) /* USB Host 2.0 Controller (PXA935) */
+
+#define IRQ_MMC3_PXA935 PXA_IRQ(72) /* MMC3 Controller (PXA935) */
+#define IRQ_MMC4_PXA935 PXA_IRQ(73) /* MMC4 Controller (PXA935) */
+#define IRQ_MMC5_PXA935 PXA_IRQ(74) /* MMC5 Controller (PXA935) */
+
+#define IRQ_U2P PXA_IRQ(93) /* USB PHY D+/D- Lines (PXA935) */
+#endif
+
+#ifdef CONFIG_CPU_PXA930
+#define IRQ_ENHROT PXA_IRQ(37) /* Enhanced Rotary (PXA930) */
+#define IRQ_ACIPC0 PXA_IRQ(5)
+#define IRQ_ACIPC1 PXA_IRQ(40)
+#define IRQ_ACIPC2 PXA_IRQ(19)
+#define IRQ_TRKBALL PXA_IRQ(43) /* Track Ball */
+#endif
+
+#ifdef CONFIG_CPU_PXA950
+#define IRQ_GC500 PXA_IRQ(70) /* Graphics Controller (PXA950) */
+#endif
+
+#define PXA_GPIO_IRQ_BASE PXA_IRQ(96)
+#define PXA_GPIO_IRQ_NUM (192)
#define GPIO_2_x_TO_IRQ(x) (PXA_GPIO_IRQ_BASE + (x))
#define IRQ_GPIO(x) (((x) < 2) ? (IRQ_GPIO0 + (x)) : GPIO_2_x_TO_IRQ(x))
#define IRQ_BOARD_END (IRQ_BOARD_START + 70)
#elif defined(CONFIG_MACH_ZYLONITE)
#define IRQ_BOARD_END (IRQ_BOARD_START + 32)
+#elif defined(CONFIG_PXA_EZX)
+#define IRQ_BOARD_END (IRQ_BOARD_START + 23)
#else
#define IRQ_BOARD_END (IRQ_BOARD_START + 16)
#endif
#define MAINSTONE_S1_STSCHG_IRQ MAINSTONE_IRQ(14)
#define MAINSTONE_S1_IRQ MAINSTONE_IRQ(15)
+/* Balloon3 Interrupts */
+#define BALLOON3_IRQ(x) (IRQ_BOARD_START + (x))
+
+#define BALLOON3_BP_CF_NRDY_IRQ BALLOON3_IRQ(0)
+#define BALLOON3_BP_NSTSCHG_IRQ BALLOON3_IRQ(1)
+
+#define BALLOON3_AUX_NIRQ IRQ_GPIO(BALLOON3_GPIO_AUX_NIRQ)
+#define BALLOON3_CODEC_IRQ IRQ_GPIO(BALLOON3_GPIO_CODEC_IRQ)
+#define BALLOON3_S0_CD_IRQ IRQ_GPIO(BALLOON3_GPIO_S0_CD)
+
/* LoCoMo Interrupts (CONFIG_SHARP_LOCOMO) */
#define IRQ_LOCOMO_KEY_BASE (IRQ_BOARD_START + 0)
#define IRQ_LOCOMO_GPIO_BASE (IRQ_BOARD_START + 1)
#ifndef __ASM_ARCH_MFP_H
#define __ASM_ARCH_MFP_H
-#define mfp_to_gpio(m) ((m) % 128)
-
-/* list of all the configurable MFP pins */
-enum {
- MFP_PIN_INVALID = -1,
-
- MFP_PIN_GPIO0 = 0,
- MFP_PIN_GPIO1,
- MFP_PIN_GPIO2,
- MFP_PIN_GPIO3,
- MFP_PIN_GPIO4,
- MFP_PIN_GPIO5,
- MFP_PIN_GPIO6,
- MFP_PIN_GPIO7,
- MFP_PIN_GPIO8,
- MFP_PIN_GPIO9,
- MFP_PIN_GPIO10,
- MFP_PIN_GPIO11,
- MFP_PIN_GPIO12,
- MFP_PIN_GPIO13,
- MFP_PIN_GPIO14,
- MFP_PIN_GPIO15,
- MFP_PIN_GPIO16,
- MFP_PIN_GPIO17,
- MFP_PIN_GPIO18,
- MFP_PIN_GPIO19,
- MFP_PIN_GPIO20,
- MFP_PIN_GPIO21,
- MFP_PIN_GPIO22,
- MFP_PIN_GPIO23,
- MFP_PIN_GPIO24,
- MFP_PIN_GPIO25,
- MFP_PIN_GPIO26,
- MFP_PIN_GPIO27,
- MFP_PIN_GPIO28,
- MFP_PIN_GPIO29,
- MFP_PIN_GPIO30,
- MFP_PIN_GPIO31,
- MFP_PIN_GPIO32,
- MFP_PIN_GPIO33,
- MFP_PIN_GPIO34,
- MFP_PIN_GPIO35,
- MFP_PIN_GPIO36,
- MFP_PIN_GPIO37,
- MFP_PIN_GPIO38,
- MFP_PIN_GPIO39,
- MFP_PIN_GPIO40,
- MFP_PIN_GPIO41,
- MFP_PIN_GPIO42,
- MFP_PIN_GPIO43,
- MFP_PIN_GPIO44,
- MFP_PIN_GPIO45,
- MFP_PIN_GPIO46,
- MFP_PIN_GPIO47,
- MFP_PIN_GPIO48,
- MFP_PIN_GPIO49,
- MFP_PIN_GPIO50,
- MFP_PIN_GPIO51,
- MFP_PIN_GPIO52,
- MFP_PIN_GPIO53,
- MFP_PIN_GPIO54,
- MFP_PIN_GPIO55,
- MFP_PIN_GPIO56,
- MFP_PIN_GPIO57,
- MFP_PIN_GPIO58,
- MFP_PIN_GPIO59,
- MFP_PIN_GPIO60,
- MFP_PIN_GPIO61,
- MFP_PIN_GPIO62,
- MFP_PIN_GPIO63,
- MFP_PIN_GPIO64,
- MFP_PIN_GPIO65,
- MFP_PIN_GPIO66,
- MFP_PIN_GPIO67,
- MFP_PIN_GPIO68,
- MFP_PIN_GPIO69,
- MFP_PIN_GPIO70,
- MFP_PIN_GPIO71,
- MFP_PIN_GPIO72,
- MFP_PIN_GPIO73,
- MFP_PIN_GPIO74,
- MFP_PIN_GPIO75,
- MFP_PIN_GPIO76,
- MFP_PIN_GPIO77,
- MFP_PIN_GPIO78,
- MFP_PIN_GPIO79,
- MFP_PIN_GPIO80,
- MFP_PIN_GPIO81,
- MFP_PIN_GPIO82,
- MFP_PIN_GPIO83,
- MFP_PIN_GPIO84,
- MFP_PIN_GPIO85,
- MFP_PIN_GPIO86,
- MFP_PIN_GPIO87,
- MFP_PIN_GPIO88,
- MFP_PIN_GPIO89,
- MFP_PIN_GPIO90,
- MFP_PIN_GPIO91,
- MFP_PIN_GPIO92,
- MFP_PIN_GPIO93,
- MFP_PIN_GPIO94,
- MFP_PIN_GPIO95,
- MFP_PIN_GPIO96,
- MFP_PIN_GPIO97,
- MFP_PIN_GPIO98,
- MFP_PIN_GPIO99,
- MFP_PIN_GPIO100,
- MFP_PIN_GPIO101,
- MFP_PIN_GPIO102,
- MFP_PIN_GPIO103,
- MFP_PIN_GPIO104,
- MFP_PIN_GPIO105,
- MFP_PIN_GPIO106,
- MFP_PIN_GPIO107,
- MFP_PIN_GPIO108,
- MFP_PIN_GPIO109,
- MFP_PIN_GPIO110,
- MFP_PIN_GPIO111,
- MFP_PIN_GPIO112,
- MFP_PIN_GPIO113,
- MFP_PIN_GPIO114,
- MFP_PIN_GPIO115,
- MFP_PIN_GPIO116,
- MFP_PIN_GPIO117,
- MFP_PIN_GPIO118,
- MFP_PIN_GPIO119,
- MFP_PIN_GPIO120,
- MFP_PIN_GPIO121,
- MFP_PIN_GPIO122,
- MFP_PIN_GPIO123,
- MFP_PIN_GPIO124,
- MFP_PIN_GPIO125,
- MFP_PIN_GPIO126,
- MFP_PIN_GPIO127,
- MFP_PIN_GPIO0_2,
- MFP_PIN_GPIO1_2,
- MFP_PIN_GPIO2_2,
- MFP_PIN_GPIO3_2,
- MFP_PIN_GPIO4_2,
- MFP_PIN_GPIO5_2,
- MFP_PIN_GPIO6_2,
- MFP_PIN_GPIO7_2,
- MFP_PIN_GPIO8_2,
- MFP_PIN_GPIO9_2,
- MFP_PIN_GPIO10_2,
- MFP_PIN_GPIO11_2,
- MFP_PIN_GPIO12_2,
- MFP_PIN_GPIO13_2,
- MFP_PIN_GPIO14_2,
- MFP_PIN_GPIO15_2,
- MFP_PIN_GPIO16_2,
- MFP_PIN_GPIO17_2,
-
- MFP_PIN_ULPI_STP,
- MFP_PIN_ULPI_NXT,
- MFP_PIN_ULPI_DIR,
-
- MFP_PIN_nXCVREN,
- MFP_PIN_DF_CLE_nOE,
- MFP_PIN_DF_nADV1_ALE,
- MFP_PIN_DF_SCLK_E,
- MFP_PIN_DF_SCLK_S,
- MFP_PIN_nBE0,
- MFP_PIN_nBE1,
- MFP_PIN_DF_nADV2_ALE,
- MFP_PIN_DF_INT_RnB,
- MFP_PIN_DF_nCS0,
- MFP_PIN_DF_nCS1,
- MFP_PIN_nLUA,
- MFP_PIN_nLLA,
- MFP_PIN_DF_nWE,
- MFP_PIN_DF_ALE_nWE,
- MFP_PIN_DF_nRE_nOE,
- MFP_PIN_DF_ADDR0,
- MFP_PIN_DF_ADDR1,
- MFP_PIN_DF_ADDR2,
- MFP_PIN_DF_ADDR3,
- MFP_PIN_DF_IO0,
- MFP_PIN_DF_IO1,
- MFP_PIN_DF_IO2,
- MFP_PIN_DF_IO3,
- MFP_PIN_DF_IO4,
- MFP_PIN_DF_IO5,
- MFP_PIN_DF_IO6,
- MFP_PIN_DF_IO7,
- MFP_PIN_DF_IO8,
- MFP_PIN_DF_IO9,
- MFP_PIN_DF_IO10,
- MFP_PIN_DF_IO11,
- MFP_PIN_DF_IO12,
- MFP_PIN_DF_IO13,
- MFP_PIN_DF_IO14,
- MFP_PIN_DF_IO15,
-
- /* additional pins on PXA930 */
- MFP_PIN_GSIM_UIO,
- MFP_PIN_GSIM_UCLK,
- MFP_PIN_GSIM_UDET,
- MFP_PIN_GSIM_nURST,
- MFP_PIN_PMIC_INT,
- MFP_PIN_RDY,
-
- MFP_PIN_MAX,
-};
-
-/*
- * a possible MFP configuration is represented by a 32-bit integer
- *
- * bit 0.. 9 - MFP Pin Number (1024 Pins Maximum)
- * bit 10..12 - Alternate Function Selection
- * bit 13..15 - Drive Strength
- * bit 16..18 - Low Power Mode State
- * bit 19..20 - Low Power Mode Edge Detection
- * bit 21..22 - Run Mode Pull State
- *
- * to facilitate the definition, the following macros are provided
- *
- * MFP_CFG_DEFAULT - default MFP configuration value, with
- * alternate function = 0,
- * drive strength = fast 3mA (MFP_DS03X)
- * low power mode = default
- * edge detection = none
- *
- * MFP_CFG - default MFPR value with alternate function
- * MFP_CFG_DRV - default MFPR value with alternate function and
- * pin drive strength
- * MFP_CFG_LPM - default MFPR value with alternate function and
- * low power mode
- * MFP_CFG_X - default MFPR value with alternate function,
- * pin drive strength and low power mode
- */
-
-typedef unsigned long mfp_cfg_t;
-
-#define MFP_PIN(x) ((x) & 0x3ff)
-
-#define MFP_AF0 (0x0 << 10)
-#define MFP_AF1 (0x1 << 10)
-#define MFP_AF2 (0x2 << 10)
-#define MFP_AF3 (0x3 << 10)
-#define MFP_AF4 (0x4 << 10)
-#define MFP_AF5 (0x5 << 10)
-#define MFP_AF6 (0x6 << 10)
-#define MFP_AF7 (0x7 << 10)
-#define MFP_AF_MASK (0x7 << 10)
-#define MFP_AF(x) (((x) >> 10) & 0x7)
-
-#define MFP_DS01X (0x0 << 13)
-#define MFP_DS02X (0x1 << 13)
-#define MFP_DS03X (0x2 << 13)
-#define MFP_DS04X (0x3 << 13)
-#define MFP_DS06X (0x4 << 13)
-#define MFP_DS08X (0x5 << 13)
-#define MFP_DS10X (0x6 << 13)
-#define MFP_DS13X (0x7 << 13)
-#define MFP_DS_MASK (0x7 << 13)
-#define MFP_DS(x) (((x) >> 13) & 0x7)
-
-#define MFP_LPM_DEFAULT (0x0 << 16)
-#define MFP_LPM_DRIVE_LOW (0x1 << 16)
-#define MFP_LPM_DRIVE_HIGH (0x2 << 16)
-#define MFP_LPM_PULL_LOW (0x3 << 16)
-#define MFP_LPM_PULL_HIGH (0x4 << 16)
-#define MFP_LPM_FLOAT (0x5 << 16)
-#define MFP_LPM_INPUT (0x6 << 16)
-#define MFP_LPM_STATE_MASK (0x7 << 16)
-#define MFP_LPM_STATE(x) (((x) >> 16) & 0x7)
-
-#define MFP_LPM_EDGE_NONE (0x0 << 19)
-#define MFP_LPM_EDGE_RISE (0x1 << 19)
-#define MFP_LPM_EDGE_FALL (0x2 << 19)
-#define MFP_LPM_EDGE_BOTH (0x3 << 19)
-#define MFP_LPM_EDGE_MASK (0x3 << 19)
-#define MFP_LPM_EDGE(x) (((x) >> 19) & 0x3)
-
-#define MFP_PULL_NONE (0x0 << 21)
-#define MFP_PULL_LOW (0x1 << 21)
-#define MFP_PULL_HIGH (0x2 << 21)
-#define MFP_PULL_BOTH (0x3 << 21)
-#define MFP_PULL_MASK (0x3 << 21)
-#define MFP_PULL(x) (((x) >> 21) & 0x3)
-
-#define MFP_CFG_DEFAULT (MFP_AF0 | MFP_DS03X | MFP_LPM_DEFAULT |\
- MFP_LPM_EDGE_NONE | MFP_PULL_NONE)
-
-#define MFP_CFG(pin, af) \
- ((MFP_CFG_DEFAULT & ~MFP_AF_MASK) |\
- (MFP_PIN(MFP_PIN_##pin) | MFP_##af))
-
-#define MFP_CFG_DRV(pin, af, drv) \
- ((MFP_CFG_DEFAULT & ~(MFP_AF_MASK | MFP_DS_MASK)) |\
- (MFP_PIN(MFP_PIN_##pin) | MFP_##af | MFP_##drv))
-
-#define MFP_CFG_LPM(pin, af, lpm) \
- ((MFP_CFG_DEFAULT & ~(MFP_AF_MASK | MFP_LPM_STATE_MASK)) |\
- (MFP_PIN(MFP_PIN_##pin) | MFP_##af | MFP_LPM_##lpm))
-
-#define MFP_CFG_X(pin, af, drv, lpm) \
- ((MFP_CFG_DEFAULT & ~(MFP_AF_MASK | MFP_DS_MASK | MFP_LPM_STATE_MASK)) |\
- (MFP_PIN(MFP_PIN_##pin) | MFP_##af | MFP_##drv | MFP_LPM_##lpm))
+#include <plat/mfp.h>
#endif /* __ASM_ARCH_MFP_H */
int (*get_ro)(struct device *);
void (*setpower)(struct device *, unsigned int);
void (*exit)(struct device *, void *);
+ int gpio_card_detect; /* gpio detecting card insertion */
+ int gpio_card_ro; /* gpio detecting read only toggle */
+ bool gpio_card_ro_invert; /* gpio ro is inverted */
+ int gpio_power; /* gpio powering up MMC bus */
+ bool gpio_power_invert; /* gpio power is inverted */
};
extern void pxa_set_mci_info(struct pxamci_platform_data *info);
--- /dev/null
+/*
+ * linux/include/asm-arm/arch-pxa/palmtc-gpio.h
+ *
+ * GPIOs and interrupts for Palm Tungsten|C Handheld Computer
+ *
+ * Authors: Alex Osborne <bobofdoom@gmail.com>
+ * Marek Vasut <marek.vasut@gmail.com>
+ * Holger Bocklet <bitz.email@gmx.net>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#ifndef _INCLUDE_PALMTC_H_
+#define _INCLUDE_PALMTC_H_
+
+/** HERE ARE GPIOs **/
+
+/* GPIOs */
+#define GPIO_NR_PALMTC_EARPHONE_DETECT 2
+#define GPIO_NR_PALMTC_CRADLE_DETECT 5
+#define GPIO_NR_PALMTC_HOTSYNC_BUTTON 7
+
+/* SD/MMC */
+#define GPIO_NR_PALMTC_SD_DETECT_N 12
+#define GPIO_NR_PALMTC_SD_POWER 32
+#define GPIO_NR_PALMTC_SD_READONLY 54
+
+/* WLAN */
+#define GPIO_NR_PALMTC_PCMCIA_READY 13
+#define GPIO_NR_PALMTC_PCMCIA_PWRREADY 14
+#define GPIO_NR_PALMTC_PCMCIA_POWER1 15
+#define GPIO_NR_PALMTC_PCMCIA_POWER2 33
+#define GPIO_NR_PALMTC_PCMCIA_POWER3 55
+#define GPIO_NR_PALMTC_PCMCIA_RESET 78
+
+/* UDC */
+#define GPIO_NR_PALMTC_USB_DETECT_N 4
+#define GPIO_NR_PALMTC_USB_POWER 36
+
+/* LCD/BACKLIGHT */
+#define GPIO_NR_PALMTC_BL_POWER 16
+#define GPIO_NR_PALMTC_LCD_POWER 44
+#define GPIO_NR_PALMTC_LCD_BLANK 38
+
+/* UART */
+#define GPIO_NR_PALMTC_RS232_POWER 37
+
+/* IRDA */
+#define GPIO_NR_PALMTC_IR_DISABLE 45
+
+/* IRQs */
+#define IRQ_GPIO_PALMTC_SD_DETECT_N IRQ_GPIO(GPIO_NR_PALMTC_SD_DETECT_N)
+#define IRQ_GPIO_PALMTC_WLAN_READY IRQ_GPIO(GPIO_NR_PALMTC_WLAN_READY)
+
+/* UCB1400 GPIOs */
+#define GPIO_NR_PALMTC_POWER_DETECT (0x80 | 0x00)
+#define GPIO_NR_PALMTC_HEADPHONE_DETECT (0x80 | 0x01)
+#define GPIO_NR_PALMTC_SPEAKER_ENABLE (0x80 | 0x03)
+#define GPIO_NR_PALMTC_VIBRA_POWER (0x80 | 0x05)
+#define GPIO_NR_PALMTC_LED_POWER (0x80 | 0x07)
+
+/** HERE ARE INIT VALUES **/
+#define PALMTC_UCB1400_GPIO_OFFSET 0x80
+
+/* BATTERY */
+#define PALMTC_BAT_MAX_VOLTAGE 4000 /* 4.00V maximum voltage */
+#define PALMTC_BAT_MIN_VOLTAGE 3550 /* 3.55V critical voltage */
+#define PALMTC_BAT_MAX_CURRENT 0 /* unknokn */
+#define PALMTC_BAT_MIN_CURRENT 0 /* unknown */
+#define PALMTC_BAT_MAX_CHARGE 1 /* unknown */
+#define PALMTC_BAT_MIN_CHARGE 1 /* unknown */
+#define PALMTC_MAX_LIFE_MINS 240 /* on-life in minutes */
+
+#define PALMTC_BAT_MEASURE_DELAY (HZ * 1)
+
+/* BACKLIGHT */
+#define PALMTC_MAX_INTENSITY 0xFE
+#define PALMTC_DEFAULT_INTENSITY 0x7E
+#define PALMTC_LIMIT_MASK 0x7F
+#define PALMTC_PRESCALER 0x3F
+#define PALMTC_PERIOD_NS 3500
+
+#endif
#define PALMTX_PHYS_FLASH_START PXA_CS0_PHYS /* ChipSelect 0 */
#define PALMTX_PHYS_NAND_START PXA_CS1_PHYS /* ChipSelect 1 */
+#define PALMTX_NAND_ALE_PHYS (PALMTX_PHYS_NAND_START | (1 << 24))
+#define PALMTX_NAND_CLE_PHYS (PALMTX_PHYS_NAND_START | (1 << 25))
+#define PALMTX_NAND_ALE_VIRT 0xff100000
+#define PALMTX_NAND_CLE_VIRT 0xff200000
+
/* TOUCHSCREEN */
#define AC97_LINK_FRAME 21
#define CKEN_MVED 43 /* < MVED clock enable */
/* Note: GCU clock enable bit differs on PXA300/PXA310 and PXA320 */
-#define PXA300_CKEN_GRAPHICS 42 /* Graphics controller clock enable */
-#define PXA320_CKEN_GRAPHICS 7 /* Graphics controller clock enable */
+#define CKEN_PXA300_GCU 42 /* Graphics controller clock enable */
+#define CKEN_PXA320_GCU 7 /* Graphics controller clock enable */
#endif /* __ASM_ARCH_PXA3XX_REGS_H */
u_int fixed_modes:1,
cmap_inverse:1,
cmap_static:1,
- unused:29;
+ acceleration_enabled:1,
+ unused:28;
/* The following should be defined in LCCR0
* LCCR0_Act or LCCR0_Pas Active or Passive
#define ICFP __REG(0x40D0000C) /* Interrupt Controller FIQ Pending Register */
#define ICPR __REG(0x40D00010) /* Interrupt Controller Pending Register */
#define ICCR __REG(0x40D00014) /* Interrupt Controller Control Register */
+#define ICHP __REG(0x40D00018) /* Interrupt Controller Highest Priority Register */
#define ICIP2 __REG(0x40D0009C) /* Interrupt Controller IRQ Pending Register 2 */
#define ICMR2 __REG(0x40D000A0) /* Interrupt Controller Mask Register 2 */
#define ICFP2 __REG(0x40D000A8) /* Interrupt Controller FIQ Pending Register 2 */
#define ICPR2 __REG(0x40D000AC) /* Interrupt Controller Pending Register 2 */
+#define ICIP3 __REG(0x40D00130) /* Interrupt Controller IRQ Pending Register 3 */
+#define ICMR3 __REG(0x40D00134) /* Interrupt Controller Mask Register 3 */
+#define ICLR3 __REG(0x40D00138) /* Interrupt Controller Level Register 3 */
+#define ICFP3 __REG(0x40D0013C) /* Interrupt Controller FIQ Pending Register 3 */
+#define ICPR3 __REG(0x40D00140) /* Interrupt Controller Pending Register 3 */
+
+#define IPR(x) __REG(0x40D0001C + (x < 32 ? (x << 2) \
+ : (x < 64 ? (0x94 + ((x - 32) << 2)) \
+ : (0x128 + ((x - 64) << 2)))))
+
#endif /* __ASM_MACH_REGS_INTC_H */
{
if (machine_is_littleton() || machine_is_intelmote2()
|| machine_is_csb726() || machine_is_stargate2()
- || machine_is_cm_x300())
+ || machine_is_cm_x300() || machine_is_balloon3())
UART = STUART;
}
void __init pxa_init_irq(int irq_nr, set_wake_t fn)
{
- int irq;
+ int irq, i;
pxa_internal_irq_nr = irq_nr;
_ICLR(irq) = 0; /* all IRQs are IRQ, not FIQ */
}
+ /* initialize interrupt priority */
+ if (cpu_is_pxa27x() || cpu_is_pxa3xx()) {
+ for (i = 0; i < irq_nr; i++)
+ IPR(i) = i | (1 << 31);
+ }
+
/* only unmasked interrupts kick us out of idle */
ICCR = 1;
#endif
#if defined(CONFIG_MMC_PXA) || defined(CONFIG_MMC_PXA_MODULE)
-static int littleton_mci_init(struct device *dev,
- irq_handler_t littleton_detect_int, void *data)
-{
- int err, gpio_cd = GPIO_MMC1_CARD_DETECT;
-
- err = gpio_request(gpio_cd, "mmc card detect");
- if (err)
- goto err_request_cd;
-
- gpio_direction_input(gpio_cd);
-
- err = request_irq(gpio_to_irq(gpio_cd), littleton_detect_int,
- IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
- "mmc card detect", data);
- if (err) {
- dev_err(dev, "failed to request card detect IRQ\n");
- goto err_request_irq;
- }
- return 0;
-
-err_request_irq:
- gpio_free(gpio_cd);
-err_request_cd:
- return err;
-}
-
-static void littleton_mci_exit(struct device *dev, void *data)
-{
- int gpio_cd = GPIO_MMC1_CARD_DETECT;
-
- free_irq(gpio_to_irq(gpio_cd), data);
- gpio_free(gpio_cd);
-}
-
static struct pxamci_platform_data littleton_mci_platform_data = {
- .detect_delay = 20,
- .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
- .init = littleton_mci_init,
- .exit = littleton_mci_exit,
+ .detect_delay = 20,
+ .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
+ .gpio_card_detect = GPIO_MMC1_CARD_DETECT,
+ .gpio_card_ro = -1,
+ .gpio_power = -1,
};
static void __init littleton_init_mmc(void)
}
static struct pxamci_platform_data lubbock_mci_platform_data = {
- .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
- .detect_delay = 1,
- .init = lubbock_mci_init,
- .get_ro = lubbock_mci_get_ro,
- .exit = lubbock_mci_exit,
+ .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
+ .detect_delay = 1,
+ .init = lubbock_mci_init,
+ .get_ro = lubbock_mci_get_ro,
+ .exit = lubbock_mci_exit,
+ .gpio_card_detect = -1,
+ .gpio_card_ro = -1,
+ .gpio_power = -1,
};
static void lubbock_irda_transceiver_mode(struct device *dev, int mode)
}
static struct pxaficp_platform_data lubbock_ficp_platform_data = {
- .transceiver_cap = IR_SIRMODE | IR_FIRMODE,
- .transceiver_mode = lubbock_irda_transceiver_mode,
+ .gpio_pwdown = -1,
+ .transceiver_cap = IR_SIRMODE | IR_FIRMODE,
+ .transceiver_mode = lubbock_irda_transceiver_mode,
};
static void __init lubbock_init(void)
* IRDA
*/
-static void magician_irda_transceiver_mode(struct device *dev, int mode)
-{
- gpio_set_value(GPIO83_MAGICIAN_nIR_EN, mode & IR_OFF);
- pxa2xx_transceiver_mode(dev, mode);
-}
-
static struct pxaficp_platform_data magician_ficp_info = {
- .transceiver_cap = IR_SIRMODE | IR_OFF,
- .transceiver_mode = magician_irda_transceiver_mode,
+ .gpio_pwdown = GPIO83_MAGICIAN_nIR_EN,
+ .transceiver_cap = IR_SIRMODE | IR_OFF,
};
/*
static int magician_mci_init(struct device *dev,
irq_handler_t detect_irq, void *data)
{
- int err;
-
- err = request_irq(IRQ_MAGICIAN_SD, detect_irq,
+ return request_irq(IRQ_MAGICIAN_SD, detect_irq,
IRQF_DISABLED | IRQF_SAMPLE_RANDOM,
- "MMC card detect", data);
- if (err)
- goto err_request_irq;
- err = gpio_request(EGPIO_MAGICIAN_SD_POWER, "SD_POWER");
- if (err)
- goto err_request_power;
- err = gpio_request(EGPIO_MAGICIAN_nSD_READONLY, "nSD_READONLY");
- if (err)
- goto err_request_readonly;
-
- return 0;
-
-err_request_readonly:
- gpio_free(EGPIO_MAGICIAN_SD_POWER);
-err_request_power:
- free_irq(IRQ_MAGICIAN_SD, data);
-err_request_irq:
- return err;
-}
-
-static void magician_mci_setpower(struct device *dev, unsigned int vdd)
-{
- struct pxamci_platform_data *pdata = dev->platform_data;
-
- gpio_set_value(EGPIO_MAGICIAN_SD_POWER, (1 << vdd) & pdata->ocr_mask);
-}
-
-static int magician_mci_get_ro(struct device *dev)
-{
- return (!gpio_get_value(EGPIO_MAGICIAN_nSD_READONLY));
+ "mmc card detect", data);
}
static void magician_mci_exit(struct device *dev, void *data)
{
- gpio_free(EGPIO_MAGICIAN_nSD_READONLY);
- gpio_free(EGPIO_MAGICIAN_SD_POWER);
free_irq(IRQ_MAGICIAN_SD, data);
}
static struct pxamci_platform_data magician_mci_info = {
- .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
- .init = magician_mci_init,
- .get_ro = magician_mci_get_ro,
- .setpower = magician_mci_setpower,
- .exit = magician_mci_exit,
+ .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
+ .init = magician_mci_init,
+ .exit = magician_mci_exit,
+ .gpio_card_detect = -1,
+ .gpio_card_ro = EGPIO_MAGICIAN_nSD_READONLY,
+ .gpio_card_ro_invert = 1,
+ .gpio_power = EGPIO_MAGICIAN_SD_POWER,
};
}
static struct pxamci_platform_data mainstone_mci_platform_data = {
- .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
- .init = mainstone_mci_init,
- .setpower = mainstone_mci_setpower,
- .exit = mainstone_mci_exit,
+ .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
+ .init = mainstone_mci_init,
+ .setpower = mainstone_mci_setpower,
+ .exit = mainstone_mci_exit,
+ .gpio_card_detect = -1,
+ .gpio_card_ro = -1,
+ .gpio_power = -1,
};
static void mainstone_irda_transceiver_mode(struct device *dev, int mode)
}
static struct pxaficp_platform_data mainstone_ficp_platform_data = {
- .transceiver_cap = IR_SIRMODE | IR_FIRMODE | IR_OFF,
- .transceiver_mode = mainstone_irda_transceiver_mode,
+ .gpio_pwdown = -1,
+ .transceiver_cap = IR_SIRMODE | IR_FIRMODE | IR_OFF,
+ .transceiver_mode = mainstone_irda_transceiver_mode,
};
static struct gpio_keys_button gpio_keys_button[] = {
/*
* SDIO/MMC Card controller
*/
-static void mci_setpower(struct device *dev, unsigned int vdd)
-{
- struct pxamci_platform_data *p_d = dev->platform_data;
-
- if ((1 << vdd) & p_d->ocr_mask)
- gpio_set_value(GPIO91_SDIO_EN, 1); /* enable SDIO power */
- else
- gpio_set_value(GPIO91_SDIO_EN, 0); /* disable SDIO power */
-}
-
-static int mci_get_ro(struct device *dev)
-{
- return gpio_get_value(GPIO78_SDIO_RO);
-}
-
-struct gpio_ress mci_gpios[] = {
- MIO_GPIO_IN(GPIO78_SDIO_RO, "SDIO readonly detect"),
- MIO_GPIO_IN(GPIO15_SDIO_INSERT, "SDIO insertion detect"),
- MIO_GPIO_OUT(GPIO91_SDIO_EN, 0, "SDIO power enable")
-};
-
-static void mci_exit(struct device *dev, void *data)
-{
- mio_gpio_free(ARRAY_AND_SIZE(mci_gpios));
- free_irq(gpio_to_irq(GPIO15_SDIO_INSERT), data);
-}
-
-static struct pxamci_platform_data mioa701_mci_info;
-
/**
* The card detect interrupt isn't debounced so we delay it by 250ms
* to give the card a chance to fully insert/eject.
*/
-static int mci_init(struct device *dev, irq_handler_t detect_int, void *data)
-{
- int rc;
- int irq = gpio_to_irq(GPIO15_SDIO_INSERT);
-
- rc = mio_gpio_request(ARRAY_AND_SIZE(mci_gpios));
- if (rc)
- goto err_gpio;
- /* enable RE/FE interrupt on card insertion and removal */
- rc = request_irq(irq, detect_int,
- IRQF_DISABLED | IRQF_TRIGGER_RISING |
- IRQF_TRIGGER_FALLING,
- "MMC card detect", data);
- if (rc)
- goto err_irq;
-
- mioa701_mci_info.detect_delay = msecs_to_jiffies(250);
- return 0;
-
-err_irq:
- dev_err(dev, "mioa701_mci_init: MMC/SD:"
- " can't request MMC card detect IRQ\n");
- mio_gpio_free(ARRAY_AND_SIZE(mci_gpios));
-err_gpio:
- return rc;
-}
-
static struct pxamci_platform_data mioa701_mci_info = {
- .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
- .init = mci_init,
- .get_ro = mci_get_ro,
- .setpower = mci_setpower,
- .exit = mci_exit,
+ .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
+ .gpio_card_detect = GPIO15_SDIO_INSERT,
+ .gpio_card_ro = GPIO78_SDIO_RO,
+ .gpio_power = GPIO91_SDIO_EN,
};
/* FlashRAM */
},
};
-static struct soc_camera_link iclink = {
- .bus_id = 0, /* Must match id in pxa27x_device_camera in device.c */
-};
-
/* Board I2C devices. */
static struct i2c_board_info __initdata mioa701_i2c_devices[] = {
{
- /* Must initialize before the camera(s) */
I2C_BOARD_INFO("mt9m111", 0x5d),
- .platform_data = &iclink,
},
};
+static struct soc_camera_link iclink = {
+ .bus_id = 0, /* Match id in pxa27x_device_camera in device.c */
+ .board_info = &mioa701_i2c_devices[0],
+ .i2c_adapter_id = 0,
+ .module_name = "mt9m111",
+};
+
struct i2c_pxa_platform_data i2c_pdata = {
.fast_mode = 1,
};
MIO_SIMPLE_DEV(mioa701_sound, "mioa701-wm9713", NULL)
MIO_SIMPLE_DEV(mioa701_board, "mioa701-board", NULL)
MIO_SIMPLE_DEV(gpio_vbus, "gpio-vbus", &gpio_vbus_data);
+MIO_SIMPLE_DEV(mioa701_camera, "soc-camera-pdrv",&iclink);
static struct platform_device *devices[] __initdata = {
&mioa701_gpio_keys,
&power_dev,
&strataflash,
&gpio_vbus,
+ &mioa701_camera,
&mioa701_board,
};
static struct gpio_ress global_gpios[] = {
MIO_GPIO_OUT(GPIO9_CHARGE_EN, 1, "Charger enable"),
MIO_GPIO_OUT(GPIO18_POWEROFF, 0, "Power Off"),
- MIO_GPIO_OUT(GPIO87_LCD_POWER, 0, "LCD Power")
+ MIO_GPIO_OUT(GPIO87_LCD_POWER, 0, "LCD Power"),
};
static void __init mioa701_machine_init(void)
mio_gpio_request(ARRAY_AND_SIZE(global_gpios));
bootstrap_init();
set_pxa_fb_info(&mioa701_pxafb_info);
+ mioa701_mci_info.detect_delay = msecs_to_jiffies(250);
pxa_set_mci_info(&mioa701_mci_info);
pxa_set_keypad_info(&mioa701_keypad_info);
wm97xx_bat_set_pdata(&mioa701_battery_data);
pxa_set_i2c_info(&i2c_pdata);
pxa27x_set_i2c_power_info(NULL);
pxa_set_camera_info(&mioa701_pxacamera_platform_data);
- i2c_register_board_info(0, ARRAY_AND_SIZE(mioa701_i2c_devices));
}
static void mioa701_machine_exit(void)
#include <linux/wm97xx_batt.h>
#include <linux/power_supply.h>
#include <linux/sysdev.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/physmap.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
};
/******************************************************************************
- * SD/MMC card controller
+ * NOR Flash
******************************************************************************/
-static int palmld_mci_init(struct device *dev, irq_handler_t palmld_detect_int,
- void *data)
-{
- int err = 0;
-
- /* Setup an interrupt for detecting card insert/remove events */
- err = gpio_request(GPIO_NR_PALMLD_SD_DETECT_N, "SD IRQ");
- if (err)
- goto err;
- err = gpio_direction_input(GPIO_NR_PALMLD_SD_DETECT_N);
- if (err)
- goto err2;
- err = request_irq(gpio_to_irq(GPIO_NR_PALMLD_SD_DETECT_N),
- palmld_detect_int, IRQF_DISABLED | IRQF_SAMPLE_RANDOM |
- IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
- "SD/MMC card detect", data);
- if (err) {
- printk(KERN_ERR "%s: cannot request SD/MMC card detect IRQ\n",
- __func__);
- goto err2;
+static struct mtd_partition palmld_partitions[] = {
+ {
+ .name = "Flash",
+ .offset = 0x00000000,
+ .size = MTDPART_SIZ_FULL,
+ .mask_flags = 0
}
+};
- err = gpio_request(GPIO_NR_PALMLD_SD_POWER, "SD_POWER");
- if (err)
- goto err3;
- err = gpio_direction_output(GPIO_NR_PALMLD_SD_POWER, 0);
- if (err)
- goto err4;
-
- err = gpio_request(GPIO_NR_PALMLD_SD_READONLY, "SD_READONLY");
- if (err)
- goto err4;
- err = gpio_direction_input(GPIO_NR_PALMLD_SD_READONLY);
- if (err)
- goto err5;
-
- printk(KERN_DEBUG "%s: irq registered\n", __func__);
-
- return 0;
-
-err5:
- gpio_free(GPIO_NR_PALMLD_SD_READONLY);
-err4:
- gpio_free(GPIO_NR_PALMLD_SD_POWER);
-err3:
- free_irq(gpio_to_irq(GPIO_NR_PALMLD_SD_DETECT_N), data);
-err2:
- gpio_free(GPIO_NR_PALMLD_SD_DETECT_N);
-err:
- return err;
-}
-
-static void palmld_mci_exit(struct device *dev, void *data)
-{
- gpio_free(GPIO_NR_PALMLD_SD_READONLY);
- gpio_free(GPIO_NR_PALMLD_SD_POWER);
- free_irq(gpio_to_irq(GPIO_NR_PALMLD_SD_DETECT_N), data);
- gpio_free(GPIO_NR_PALMLD_SD_DETECT_N);
-}
+static struct physmap_flash_data palmld_flash_data[] = {
+ {
+ .width = 2, /* bankwidth in bytes */
+ .parts = palmld_partitions,
+ .nr_parts = ARRAY_SIZE(palmld_partitions)
+ }
+};
-static void palmld_mci_power(struct device *dev, unsigned int vdd)
-{
- struct pxamci_platform_data *p_d = dev->platform_data;
- gpio_set_value(GPIO_NR_PALMLD_SD_POWER, p_d->ocr_mask & (1 << vdd));
-}
+static struct resource palmld_flash_resource = {
+ .start = PXA_CS0_PHYS,
+ .end = PXA_CS0_PHYS + SZ_4M - 1,
+ .flags = IORESOURCE_MEM,
+};
-static int palmld_mci_get_ro(struct device *dev)
-{
- return gpio_get_value(GPIO_NR_PALMLD_SD_READONLY);
-}
+static struct platform_device palmld_flash = {
+ .name = "physmap-flash",
+ .id = 0,
+ .resource = &palmld_flash_resource,
+ .num_resources = 1,
+ .dev = {
+ .platform_data = palmld_flash_data,
+ },
+};
+/******************************************************************************
+ * SD/MMC card controller
+ ******************************************************************************/
static struct pxamci_platform_data palmld_mci_platform_data = {
- .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
- .setpower = palmld_mci_power,
- .get_ro = palmld_mci_get_ro,
- .init = palmld_mci_init,
- .exit = palmld_mci_exit,
+ .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
+ .gpio_card_detect = GPIO_NR_PALMLD_SD_DETECT_N,
+ .gpio_card_ro = GPIO_NR_PALMLD_SD_READONLY,
+ .gpio_power = GPIO_NR_PALMLD_SD_POWER,
+ .detect_delay = 20,
};
/******************************************************************************
/******************************************************************************
* IrDA
******************************************************************************/
-static int palmld_irda_startup(struct device *dev)
-{
- int err;
- err = gpio_request(GPIO_NR_PALMLD_IR_DISABLE, "IR DISABLE");
- if (err)
- goto err;
- err = gpio_direction_output(GPIO_NR_PALMLD_IR_DISABLE, 1);
- if (err)
- gpio_free(GPIO_NR_PALMLD_IR_DISABLE);
-err:
- return err;
-}
-
-static void palmld_irda_shutdown(struct device *dev)
-{
- gpio_free(GPIO_NR_PALMLD_IR_DISABLE);
-}
-
-static void palmld_irda_transceiver_mode(struct device *dev, int mode)
-{
- gpio_set_value(GPIO_NR_PALMLD_IR_DISABLE, mode & IR_OFF);
- pxa2xx_transceiver_mode(dev, mode);
-}
-
static struct pxaficp_platform_data palmld_ficp_platform_data = {
- .startup = palmld_irda_startup,
- .shutdown = palmld_irda_shutdown,
- .transceiver_cap = IR_SIRMODE | IR_FIRMODE | IR_OFF,
- .transceiver_mode = palmld_irda_transceiver_mode,
+ .gpio_pwdown = GPIO_NR_PALMLD_IR_DISABLE,
+ .transceiver_cap = IR_SIRMODE | IR_OFF,
};
/******************************************************************************
&power_supply,
&palmld_asoc,
&palmld_hdd,
+ &palmld_flash,
};
static struct map_desc palmld_io_desc[] __initdata = {
/******************************************************************************
* SD/MMC card controller
******************************************************************************/
-static int palmt5_mci_init(struct device *dev, irq_handler_t palmt5_detect_int,
- void *data)
-{
- int err = 0;
-
- /* Setup an interrupt for detecting card insert/remove events */
- err = gpio_request(GPIO_NR_PALMT5_SD_DETECT_N, "SD IRQ");
- if (err)
- goto err;
- err = gpio_direction_input(GPIO_NR_PALMT5_SD_DETECT_N);
- if (err)
- goto err2;
- err = request_irq(gpio_to_irq(GPIO_NR_PALMT5_SD_DETECT_N),
- palmt5_detect_int, IRQF_DISABLED | IRQF_SAMPLE_RANDOM |
- IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
- "SD/MMC card detect", data);
- if (err) {
- printk(KERN_ERR "%s: cannot request SD/MMC card detect IRQ\n",
- __func__);
- goto err2;
- }
-
- err = gpio_request(GPIO_NR_PALMT5_SD_POWER, "SD_POWER");
- if (err)
- goto err3;
- err = gpio_direction_output(GPIO_NR_PALMT5_SD_POWER, 0);
- if (err)
- goto err4;
-
- err = gpio_request(GPIO_NR_PALMT5_SD_READONLY, "SD_READONLY");
- if (err)
- goto err4;
- err = gpio_direction_input(GPIO_NR_PALMT5_SD_READONLY);
- if (err)
- goto err5;
-
- printk(KERN_DEBUG "%s: irq registered\n", __func__);
-
- return 0;
-
-err5:
- gpio_free(GPIO_NR_PALMT5_SD_READONLY);
-err4:
- gpio_free(GPIO_NR_PALMT5_SD_POWER);
-err3:
- free_irq(gpio_to_irq(GPIO_NR_PALMT5_SD_DETECT_N), data);
-err2:
- gpio_free(GPIO_NR_PALMT5_SD_DETECT_N);
-err:
- return err;
-}
-
-static void palmt5_mci_exit(struct device *dev, void *data)
-{
- gpio_free(GPIO_NR_PALMT5_SD_READONLY);
- gpio_free(GPIO_NR_PALMT5_SD_POWER);
- free_irq(IRQ_GPIO_PALMT5_SD_DETECT_N, data);
- gpio_free(GPIO_NR_PALMT5_SD_DETECT_N);
-}
-
-static void palmt5_mci_power(struct device *dev, unsigned int vdd)
-{
- struct pxamci_platform_data *p_d = dev->platform_data;
- gpio_set_value(GPIO_NR_PALMT5_SD_POWER, p_d->ocr_mask & (1 << vdd));
-}
-
-static int palmt5_mci_get_ro(struct device *dev)
-{
- return gpio_get_value(GPIO_NR_PALMT5_SD_READONLY);
-}
-
static struct pxamci_platform_data palmt5_mci_platform_data = {
- .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
- .setpower = palmt5_mci_power,
- .get_ro = palmt5_mci_get_ro,
- .init = palmt5_mci_init,
- .exit = palmt5_mci_exit,
+ .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
+ .gpio_card_detect = GPIO_NR_PALMT5_SD_DETECT_N,
+ .gpio_card_ro = GPIO_NR_PALMT5_SD_READONLY,
+ .gpio_power = GPIO_NR_PALMT5_SD_POWER,
+ .detect_delay = 20,
};
/******************************************************************************
/******************************************************************************
* IrDA
******************************************************************************/
-static int palmt5_irda_startup(struct device *dev)
-{
- int err;
- err = gpio_request(GPIO_NR_PALMT5_IR_DISABLE, "IR DISABLE");
- if (err)
- goto err;
- err = gpio_direction_output(GPIO_NR_PALMT5_IR_DISABLE, 1);
- if (err)
- gpio_free(GPIO_NR_PALMT5_IR_DISABLE);
-err:
- return err;
-}
-
-static void palmt5_irda_shutdown(struct device *dev)
-{
- gpio_free(GPIO_NR_PALMT5_IR_DISABLE);
-}
-
-static void palmt5_irda_transceiver_mode(struct device *dev, int mode)
-{
- gpio_set_value(GPIO_NR_PALMT5_IR_DISABLE, mode & IR_OFF);
- pxa2xx_transceiver_mode(dev, mode);
-}
-
static struct pxaficp_platform_data palmt5_ficp_platform_data = {
- .startup = palmt5_irda_startup,
- .shutdown = palmt5_irda_shutdown,
- .transceiver_cap = IR_SIRMODE | IR_FIRMODE | IR_OFF,
- .transceiver_mode = palmt5_irda_transceiver_mode,
+ .gpio_pwdown = GPIO_NR_PALMT5_IR_DISABLE,
+ .transceiver_cap = IR_SIRMODE | IR_OFF,
};
/******************************************************************************
--- /dev/null
+/*
+ * linux/arch/arm/mach-pxa/palmtc.c
+ *
+ * Support for the Palm Tungsten|C
+ *
+ * Author: Marek Vasut <marek.vasut@gmail.com>
+ *
+ * Based on work of:
+ * Petr Blaha <p3t3@centrum.cz>
+ * Chetan S. Kumar <shivakumar.chetan@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/platform_device.h>
+#include <linux/delay.h>
+#include <linux/irq.h>
+#include <linux/input.h>
+#include <linux/pwm_backlight.h>
+#include <linux/gpio.h>
+#include <linux/input/matrix_keypad.h>
+#include <linux/ucb1400.h>
+#include <linux/power_supply.h>
+#include <linux/gpio_keys.h>
+#include <linux/mtd/physmap.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+
+#include <mach/audio.h>
+#include <mach/palmtc.h>
+#include <mach/mmc.h>
+#include <mach/pxafb.h>
+#include <mach/mfp-pxa25x.h>
+#include <mach/irda.h>
+#include <mach/udc.h>
+#include <mach/pxa2xx-regs.h>
+
+#include "generic.h"
+#include "devices.h"
+
+/******************************************************************************
+ * Pin configuration
+ ******************************************************************************/
+static unsigned long palmtc_pin_config[] __initdata = {
+ /* MMC */
+ GPIO6_MMC_CLK,
+ GPIO8_MMC_CS0,
+ GPIO12_GPIO, /* detect */
+ GPIO32_GPIO, /* power */
+ GPIO54_GPIO, /* r/o switch */
+
+ /* PCMCIA */
+ GPIO52_nPCE_1,
+ GPIO53_nPCE_2,
+ GPIO50_nPIOR,
+ GPIO51_nPIOW,
+ GPIO49_nPWE,
+ GPIO48_nPOE,
+ GPIO52_nPCE_1,
+ GPIO53_nPCE_2,
+ GPIO57_nIOIS16,
+ GPIO56_nPWAIT,
+
+ /* AC97 */
+ GPIO28_AC97_BITCLK,
+ GPIO29_AC97_SDATA_IN_0,
+ GPIO30_AC97_SDATA_OUT,
+ GPIO31_AC97_SYNC,
+
+ /* IrDA */
+ GPIO45_GPIO, /* ir disable */
+ GPIO46_FICP_RXD,
+ GPIO47_FICP_TXD,
+
+ /* PWM */
+ GPIO17_PWM1_OUT,
+
+ /* USB */
+ GPIO4_GPIO, /* detect */
+ GPIO36_GPIO, /* pullup */
+
+ /* LCD */
+ GPIO58_LCD_LDD_0,
+ GPIO59_LCD_LDD_1,
+ GPIO60_LCD_LDD_2,
+ GPIO61_LCD_LDD_3,
+ GPIO62_LCD_LDD_4,
+ GPIO63_LCD_LDD_5,
+ GPIO64_LCD_LDD_6,
+ GPIO65_LCD_LDD_7,
+ GPIO66_LCD_LDD_8,
+ GPIO67_LCD_LDD_9,
+ GPIO68_LCD_LDD_10,
+ GPIO69_LCD_LDD_11,
+ GPIO70_LCD_LDD_12,
+ GPIO71_LCD_LDD_13,
+ GPIO72_LCD_LDD_14,
+ GPIO73_LCD_LDD_15,
+ GPIO74_LCD_FCLK,
+ GPIO75_LCD_LCLK,
+ GPIO76_LCD_PCLK,
+ GPIO77_LCD_BIAS,
+
+ /* MATRIX KEYPAD */
+ GPIO0_GPIO | WAKEUP_ON_EDGE_BOTH, /* in 0 */
+ GPIO9_GPIO | WAKEUP_ON_EDGE_BOTH, /* in 1 */
+ GPIO10_GPIO | WAKEUP_ON_EDGE_BOTH, /* in 2 */
+ GPIO11_GPIO | WAKEUP_ON_EDGE_BOTH, /* in 3 */
+ GPIO18_GPIO | MFP_LPM_DRIVE_LOW, /* out 0 */
+ GPIO19_GPIO | MFP_LPM_DRIVE_LOW, /* out 1 */
+ GPIO20_GPIO | MFP_LPM_DRIVE_LOW, /* out 2 */
+ GPIO21_GPIO | MFP_LPM_DRIVE_LOW, /* out 3 */
+ GPIO22_GPIO | MFP_LPM_DRIVE_LOW, /* out 4 */
+ GPIO23_GPIO | MFP_LPM_DRIVE_LOW, /* out 5 */
+ GPIO24_GPIO | MFP_LPM_DRIVE_LOW, /* out 6 */
+ GPIO25_GPIO | MFP_LPM_DRIVE_LOW, /* out 7 */
+ GPIO26_GPIO | MFP_LPM_DRIVE_LOW, /* out 8 */
+ GPIO27_GPIO | MFP_LPM_DRIVE_LOW, /* out 9 */
+ GPIO79_GPIO | MFP_LPM_DRIVE_LOW, /* out 10 */
+ GPIO80_GPIO | MFP_LPM_DRIVE_LOW, /* out 11 */
+
+ /* PXA GPIO KEYS */
+ GPIO7_GPIO | WAKEUP_ON_EDGE_BOTH, /* hotsync button on cradle */
+
+ /* MISC */
+ GPIO1_RST, /* reset */
+ GPIO2_GPIO, /* earphone detect */
+ GPIO16_GPIO, /* backlight switch */
+};
+
+/******************************************************************************
+ * SD/MMC card controller
+ ******************************************************************************/
+static struct pxamci_platform_data palmtc_mci_platform_data = {
+ .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
+ .gpio_power = GPIO_NR_PALMTC_SD_POWER,
+ .gpio_card_ro = GPIO_NR_PALMTC_SD_READONLY,
+ .gpio_card_detect = GPIO_NR_PALMTC_SD_DETECT_N,
+ .detect_delay = 20,
+};
+
+/******************************************************************************
+ * GPIO keys
+ ******************************************************************************/
+static struct gpio_keys_button palmtc_pxa_buttons[] = {
+ {KEY_F8, GPIO_NR_PALMTC_HOTSYNC_BUTTON, 1, "HotSync Button", EV_KEY, 1},
+};
+
+static struct gpio_keys_platform_data palmtc_pxa_keys_data = {
+ .buttons = palmtc_pxa_buttons,
+ .nbuttons = ARRAY_SIZE(palmtc_pxa_buttons),
+};
+
+static struct platform_device palmtc_pxa_keys = {
+ .name = "gpio-keys",
+ .id = -1,
+ .dev = {
+ .platform_data = &palmtc_pxa_keys_data,
+ },
+};
+
+/******************************************************************************
+ * Backlight
+ ******************************************************************************/
+static int palmtc_backlight_init(struct device *dev)
+{
+ int ret;
+
+ ret = gpio_request(GPIO_NR_PALMTC_BL_POWER, "BL POWER");
+ if (ret)
+ goto err;
+ ret = gpio_direction_output(GPIO_NR_PALMTC_BL_POWER, 1);
+ if (ret)
+ goto err2;
+
+ return 0;
+
+err2:
+ gpio_free(GPIO_NR_PALMTC_BL_POWER);
+err:
+ return ret;
+}
+
+static int palmtc_backlight_notify(int brightness)
+{
+ /* backlight is on when GPIO16 AF0 is high */
+ gpio_set_value(GPIO_NR_PALMTC_BL_POWER, brightness);
+ return brightness;
+}
+
+static void palmtc_backlight_exit(struct device *dev)
+{
+ gpio_free(GPIO_NR_PALMTC_BL_POWER);
+}
+
+static struct platform_pwm_backlight_data palmtc_backlight_data = {
+ .pwm_id = 1,
+ .max_brightness = PALMTC_MAX_INTENSITY,
+ .dft_brightness = PALMTC_MAX_INTENSITY,
+ .pwm_period_ns = PALMTC_PERIOD_NS,
+ .init = palmtc_backlight_init,
+ .notify = palmtc_backlight_notify,
+ .exit = palmtc_backlight_exit,
+};
+
+static struct platform_device palmtc_backlight = {
+ .name = "pwm-backlight",
+ .dev = {
+ .parent = &pxa25x_device_pwm1.dev,
+ .platform_data = &palmtc_backlight_data,
+ },
+};
+
+/******************************************************************************
+ * IrDA
+ ******************************************************************************/
+static struct pxaficp_platform_data palmtc_ficp_platform_data = {
+ .gpio_pwdown = GPIO_NR_PALMTC_IR_DISABLE,
+ .transceiver_cap = IR_SIRMODE | IR_OFF,
+};
+
+/******************************************************************************
+ * Keyboard
+ ******************************************************************************/
+static const uint32_t palmtc_matrix_keys[] = {
+ KEY(0, 0, KEY_F1),
+ KEY(0, 1, KEY_X),
+ KEY(0, 2, KEY_POWER),
+ KEY(0, 3, KEY_TAB),
+ KEY(0, 4, KEY_A),
+ KEY(0, 5, KEY_Q),
+ KEY(0, 6, KEY_LEFTSHIFT),
+ KEY(0, 7, KEY_Z),
+ KEY(0, 8, KEY_S),
+ KEY(0, 9, KEY_W),
+ KEY(0, 10, KEY_E),
+ KEY(0, 11, KEY_UP),
+
+ KEY(1, 0, KEY_F2),
+ KEY(1, 1, KEY_DOWN),
+ KEY(1, 3, KEY_D),
+ KEY(1, 4, KEY_C),
+ KEY(1, 5, KEY_F),
+ KEY(1, 6, KEY_R),
+ KEY(1, 7, KEY_SPACE),
+ KEY(1, 8, KEY_V),
+ KEY(1, 9, KEY_G),
+ KEY(1, 10, KEY_T),
+ KEY(1, 11, KEY_LEFT),
+
+ KEY(2, 0, KEY_F3),
+ KEY(2, 1, KEY_LEFTCTRL),
+ KEY(2, 3, KEY_H),
+ KEY(2, 4, KEY_Y),
+ KEY(2, 5, KEY_N),
+ KEY(2, 6, KEY_J),
+ KEY(2, 7, KEY_U),
+ KEY(2, 8, KEY_M),
+ KEY(2, 9, KEY_K),
+ KEY(2, 10, KEY_I),
+ KEY(2, 11, KEY_RIGHT),
+
+ KEY(3, 0, KEY_F4),
+ KEY(3, 1, KEY_ENTER),
+ KEY(3, 3, KEY_DOT),
+ KEY(3, 4, KEY_L),
+ KEY(3, 5, KEY_O),
+ KEY(3, 6, KEY_LEFTALT),
+ KEY(3, 7, KEY_ENTER),
+ KEY(3, 8, KEY_BACKSPACE),
+ KEY(3, 9, KEY_P),
+ KEY(3, 10, KEY_B),
+ KEY(3, 11, KEY_FN),
+};
+
+const struct matrix_keymap_data palmtc_keymap_data = {
+ .keymap = palmtc_matrix_keys,
+ .keymap_size = ARRAY_SIZE(palmtc_matrix_keys),
+};
+
+const static unsigned int palmtc_keypad_row_gpios[] = {
+ 0, 9, 10, 11
+};
+
+const static unsigned int palmtc_keypad_col_gpios[] = {
+ 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 79, 80
+};
+
+static struct matrix_keypad_platform_data palmtc_keypad_platform_data = {
+ .keymap_data = &palmtc_keymap_data,
+ .col_gpios = palmtc_keypad_row_gpios,
+ .num_col_gpios = 12,
+ .row_gpios = palmtc_keypad_col_gpios,
+ .num_row_gpios = 4,
+ .active_low = 1,
+
+ .debounce_ms = 20,
+ .col_scan_delay_us = 5,
+};
+
+static struct platform_device palmtc_keyboard = {
+ .name = "matrix-keypad",
+ .id = -1,
+ .dev = {
+ .platform_data = &palmtc_keypad_platform_data,
+ },
+};
+
+/******************************************************************************
+ * UDC
+ ******************************************************************************/
+static struct pxa2xx_udc_mach_info palmtc_udc_info __initdata = {
+ .gpio_vbus = GPIO_NR_PALMTC_USB_DETECT_N,
+ .gpio_vbus_inverted = 1,
+ .gpio_pullup = GPIO_NR_PALMTC_USB_POWER,
+};
+
+/******************************************************************************
+ * Touchscreen / Battery / GPIO-extender
+ ******************************************************************************/
+static struct platform_device palmtc_ucb1400_core = {
+ .name = "ucb1400_core",
+ .id = -1,
+};
+
+/******************************************************************************
+ * NOR Flash
+ ******************************************************************************/
+static struct resource palmtc_flash_resource = {
+ .start = PXA_CS0_PHYS,
+ .end = PXA_CS0_PHYS + SZ_16M - 1,
+ .flags = IORESOURCE_MEM,
+};
+
+static struct mtd_partition palmtc_flash_parts[] = {
+ {
+ .name = "U-Boot Bootloader",
+ .offset = 0x0,
+ .size = 0x40000,
+ },
+ {
+ .name = "Linux Kernel",
+ .offset = 0x40000,
+ .size = 0x2c0000,
+ },
+ {
+ .name = "Filesystem",
+ .offset = 0x300000,
+ .size = 0xcc0000,
+ },
+ {
+ .name = "U-Boot Environment",
+ .offset = 0xfc0000,
+ .size = MTDPART_SIZ_FULL,
+ },
+};
+
+static struct physmap_flash_data palmtc_flash_data = {
+ .width = 4,
+ .parts = palmtc_flash_parts,
+ .nr_parts = ARRAY_SIZE(palmtc_flash_parts),
+};
+
+static struct platform_device palmtc_flash = {
+ .name = "physmap-flash",
+ .id = -1,
+ .resource = &palmtc_flash_resource,
+ .num_resources = 1,
+ .dev = {
+ .platform_data = &palmtc_flash_data,
+ },
+};
+
+/******************************************************************************
+ * Framebuffer
+ ******************************************************************************/
+static struct pxafb_mode_info palmtc_lcd_modes[] = {
+{
+ .pixclock = 115384,
+ .xres = 320,
+ .yres = 320,
+ .bpp = 16,
+
+ .left_margin = 27,
+ .right_margin = 7,
+ .upper_margin = 7,
+ .lower_margin = 8,
+
+ .hsync_len = 6,
+ .vsync_len = 1,
+},
+};
+
+static struct pxafb_mach_info palmtc_lcd_screen = {
+ .modes = palmtc_lcd_modes,
+ .num_modes = ARRAY_SIZE(palmtc_lcd_modes),
+ .lcd_conn = LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL,
+};
+
+/******************************************************************************
+ * Machine init
+ ******************************************************************************/
+static struct platform_device *devices[] __initdata = {
+ &palmtc_backlight,
+ &palmtc_ucb1400_core,
+ &palmtc_keyboard,
+ &palmtc_pxa_keys,
+ &palmtc_flash,
+};
+
+static void __init palmtc_init(void)
+{
+ pxa2xx_mfp_config(ARRAY_AND_SIZE(palmtc_pin_config));
+
+ set_pxa_fb_info(&palmtc_lcd_screen);
+ pxa_set_mci_info(&palmtc_mci_platform_data);
+ pxa_set_udc_info(&palmtc_udc_info);
+ pxa_set_ac97_info(NULL);
+ pxa_set_ficp_info(&palmtc_ficp_platform_data);
+
+ platform_add_devices(devices, ARRAY_SIZE(devices));
+};
+
+MACHINE_START(PALMTC, "Palm Tungsten|C")
+ .phys_io = 0x40000000,
+ .boot_params = 0xa0000100,
+ .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc,
+ .map_io = pxa_map_io,
+ .init_irq = pxa25x_init_irq,
+ .timer = &pxa_timer,
+ .init_machine = palmtc_init
+MACHINE_END
/******************************************************************************
* SD/MMC card controller
******************************************************************************/
-static int palmte2_mci_init(struct device *dev,
- irq_handler_t palmte2_detect_int, void *data)
-{
- int err = 0;
-
- /* Setup an interrupt for detecting card insert/remove events */
- err = gpio_request(GPIO_NR_PALMTE2_SD_DETECT_N, "SD IRQ");
- if (err)
- goto err;
- err = gpio_direction_input(GPIO_NR_PALMTE2_SD_DETECT_N);
- if (err)
- goto err2;
- err = request_irq(gpio_to_irq(GPIO_NR_PALMTE2_SD_DETECT_N),
- palmte2_detect_int, IRQF_DISABLED | IRQF_SAMPLE_RANDOM |
- IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
- "SD/MMC card detect", data);
- if (err) {
- printk(KERN_ERR "%s: cannot request SD/MMC card detect IRQ\n",
- __func__);
- goto err2;
- }
-
- err = gpio_request(GPIO_NR_PALMTE2_SD_POWER, "SD_POWER");
- if (err)
- goto err3;
- err = gpio_direction_output(GPIO_NR_PALMTE2_SD_POWER, 0);
- if (err)
- goto err4;
-
- err = gpio_request(GPIO_NR_PALMTE2_SD_READONLY, "SD_READONLY");
- if (err)
- goto err4;
- err = gpio_direction_input(GPIO_NR_PALMTE2_SD_READONLY);
- if (err)
- goto err5;
-
- printk(KERN_DEBUG "%s: irq registered\n", __func__);
-
- return 0;
-
-err5:
- gpio_free(GPIO_NR_PALMTE2_SD_READONLY);
-err4:
- gpio_free(GPIO_NR_PALMTE2_SD_POWER);
-err3:
- free_irq(gpio_to_irq(GPIO_NR_PALMTE2_SD_DETECT_N), data);
-err2:
- gpio_free(GPIO_NR_PALMTE2_SD_DETECT_N);
-err:
- return err;
-}
-
-static void palmte2_mci_exit(struct device *dev, void *data)
-{
- gpio_free(GPIO_NR_PALMTE2_SD_READONLY);
- gpio_free(GPIO_NR_PALMTE2_SD_POWER);
- free_irq(gpio_to_irq(GPIO_NR_PALMTE2_SD_DETECT_N), data);
- gpio_free(GPIO_NR_PALMTE2_SD_DETECT_N);
-}
-
-static void palmte2_mci_power(struct device *dev, unsigned int vdd)
-{
- struct pxamci_platform_data *p_d = dev->platform_data;
- gpio_set_value(GPIO_NR_PALMTE2_SD_POWER, p_d->ocr_mask & (1 << vdd));
-}
-
-static int palmte2_mci_get_ro(struct device *dev)
-{
- return gpio_get_value(GPIO_NR_PALMTE2_SD_READONLY);
-}
-
static struct pxamci_platform_data palmte2_mci_platform_data = {
- .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
- .setpower = palmte2_mci_power,
- .get_ro = palmte2_mci_get_ro,
- .init = palmte2_mci_init,
- .exit = palmte2_mci_exit,
+ .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
+ .gpio_card_detect = GPIO_NR_PALMTE2_SD_DETECT_N,
+ .gpio_card_ro = GPIO_NR_PALMTE2_SD_READONLY,
+ .gpio_power = GPIO_NR_PALMTE2_SD_POWER,
};
/******************************************************************************
/******************************************************************************
* IrDA
******************************************************************************/
-static int palmte2_irda_startup(struct device *dev)
-{
- int err;
- err = gpio_request(GPIO_NR_PALMTE2_IR_DISABLE, "IR DISABLE");
- if (err)
- goto err;
- err = gpio_direction_output(GPIO_NR_PALMTE2_IR_DISABLE, 1);
- if (err)
- gpio_free(GPIO_NR_PALMTE2_IR_DISABLE);
-err:
- return err;
-}
-
-static void palmte2_irda_shutdown(struct device *dev)
-{
- gpio_free(GPIO_NR_PALMTE2_IR_DISABLE);
-}
-
-static void palmte2_irda_transceiver_mode(struct device *dev, int mode)
-{
- gpio_set_value(GPIO_NR_PALMTE2_IR_DISABLE, mode & IR_OFF);
- pxa2xx_transceiver_mode(dev, mode);
-}
-
static struct pxaficp_platform_data palmte2_ficp_platform_data = {
- .startup = palmte2_irda_startup,
- .shutdown = palmte2_irda_shutdown,
- .transceiver_cap = IR_SIRMODE | IR_FIRMODE | IR_OFF,
- .transceiver_mode = palmte2_irda_transceiver_mode,
+ .gpio_pwdown = GPIO_NR_PALMTE2_IR_DISABLE,
+ .transceiver_cap = IR_SIRMODE | IR_OFF,
};
/******************************************************************************
#include <linux/wm97xx_batt.h>
#include <linux/power_supply.h>
#include <linux/usb/gpio_vbus.h>
+#include <linux/mtd/nand.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/physmap.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
GPIO34_FFUART_RXD,
GPIO39_FFUART_TXD,
+ /* NAND */
+ GPIO15_nCS_1,
+ GPIO18_RDY,
+
/* MISC. */
GPIO10_GPIO, /* hotsync button */
GPIO12_GPIO, /* power detect */
};
/******************************************************************************
- * SD/MMC card controller
+ * NOR Flash
******************************************************************************/
-static int palmtx_mci_init(struct device *dev, irq_handler_t palmtx_detect_int,
- void *data)
-{
- int err = 0;
-
- /* Setup an interrupt for detecting card insert/remove events */
- err = gpio_request(GPIO_NR_PALMTX_SD_DETECT_N, "SD IRQ");
- if (err)
- goto err;
- err = gpio_direction_input(GPIO_NR_PALMTX_SD_DETECT_N);
- if (err)
- goto err2;
- err = request_irq(gpio_to_irq(GPIO_NR_PALMTX_SD_DETECT_N),
- palmtx_detect_int, IRQF_DISABLED | IRQF_SAMPLE_RANDOM |
- IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
- "SD/MMC card detect", data);
- if (err) {
- printk(KERN_ERR "%s: cannot request SD/MMC card detect IRQ\n",
- __func__);
- goto err2;
+static struct mtd_partition palmtx_partitions[] = {
+ {
+ .name = "Flash",
+ .offset = 0x00000000,
+ .size = MTDPART_SIZ_FULL,
+ .mask_flags = 0
}
+};
- err = gpio_request(GPIO_NR_PALMTX_SD_POWER, "SD_POWER");
- if (err)
- goto err3;
- err = gpio_direction_output(GPIO_NR_PALMTX_SD_POWER, 0);
- if (err)
- goto err4;
-
- err = gpio_request(GPIO_NR_PALMTX_SD_READONLY, "SD_READONLY");
- if (err)
- goto err4;
- err = gpio_direction_input(GPIO_NR_PALMTX_SD_READONLY);
- if (err)
- goto err5;
-
- printk(KERN_DEBUG "%s: irq registered\n", __func__);
-
- return 0;
-
-err5:
- gpio_free(GPIO_NR_PALMTX_SD_READONLY);
-err4:
- gpio_free(GPIO_NR_PALMTX_SD_POWER);
-err3:
- free_irq(gpio_to_irq(GPIO_NR_PALMTX_SD_DETECT_N), data);
-err2:
- gpio_free(GPIO_NR_PALMTX_SD_DETECT_N);
-err:
- return err;
-}
-
-static void palmtx_mci_exit(struct device *dev, void *data)
-{
- gpio_free(GPIO_NR_PALMTX_SD_READONLY);
- gpio_free(GPIO_NR_PALMTX_SD_POWER);
- free_irq(gpio_to_irq(GPIO_NR_PALMTX_SD_DETECT_N), data);
- gpio_free(GPIO_NR_PALMTX_SD_DETECT_N);
-}
+static struct physmap_flash_data palmtx_flash_data[] = {
+ {
+ .width = 2, /* bankwidth in bytes */
+ .parts = palmtx_partitions,
+ .nr_parts = ARRAY_SIZE(palmtx_partitions)
+ }
+};
-static void palmtx_mci_power(struct device *dev, unsigned int vdd)
-{
- struct pxamci_platform_data *p_d = dev->platform_data;
- gpio_set_value(GPIO_NR_PALMTX_SD_POWER, p_d->ocr_mask & (1 << vdd));
-}
+static struct resource palmtx_flash_resource = {
+ .start = PXA_CS0_PHYS,
+ .end = PXA_CS0_PHYS + SZ_8M - 1,
+ .flags = IORESOURCE_MEM,
+};
-static int palmtx_mci_get_ro(struct device *dev)
-{
- return gpio_get_value(GPIO_NR_PALMTX_SD_READONLY);
-}
+static struct platform_device palmtx_flash = {
+ .name = "physmap-flash",
+ .id = 0,
+ .resource = &palmtx_flash_resource,
+ .num_resources = 1,
+ .dev = {
+ .platform_data = palmtx_flash_data,
+ },
+};
+/******************************************************************************
+ * SD/MMC card controller
+ ******************************************************************************/
static struct pxamci_platform_data palmtx_mci_platform_data = {
- .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
- .setpower = palmtx_mci_power,
- .get_ro = palmtx_mci_get_ro,
- .init = palmtx_mci_init,
- .exit = palmtx_mci_exit,
+ .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
+ .gpio_card_detect = GPIO_NR_PALMTX_SD_DETECT_N,
+ .gpio_card_ro = GPIO_NR_PALMTX_SD_READONLY,
+ .gpio_power = GPIO_NR_PALMTX_SD_POWER,
+ .detect_delay = 20,
};
/******************************************************************************
/******************************************************************************
* IrDA
******************************************************************************/
-static int palmtx_irda_startup(struct device *dev)
-{
- int err;
- err = gpio_request(GPIO_NR_PALMTX_IR_DISABLE, "IR DISABLE");
- if (err)
- goto err;
- err = gpio_direction_output(GPIO_NR_PALMTX_IR_DISABLE, 1);
- if (err)
- gpio_free(GPIO_NR_PALMTX_IR_DISABLE);
-err:
- return err;
-}
-
-static void palmtx_irda_shutdown(struct device *dev)
-{
- gpio_free(GPIO_NR_PALMTX_IR_DISABLE);
-}
-
-static void palmtx_irda_transceiver_mode(struct device *dev, int mode)
-{
- gpio_set_value(GPIO_NR_PALMTX_IR_DISABLE, mode & IR_OFF);
- pxa2xx_transceiver_mode(dev, mode);
-}
-
static struct pxaficp_platform_data palmtx_ficp_platform_data = {
- .startup = palmtx_irda_startup,
- .shutdown = palmtx_irda_shutdown,
- .transceiver_cap = IR_SIRMODE | IR_FIRMODE | IR_OFF,
- .transceiver_mode = palmtx_irda_transceiver_mode,
+ .gpio_pwdown = GPIO_NR_PALMTX_IR_DISABLE,
+ .transceiver_cap = IR_SIRMODE | IR_OFF,
};
/******************************************************************************
.lcd_conn = LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL,
};
+/******************************************************************************
+ * NAND Flash
+ ******************************************************************************/
+static void palmtx_nand_cmd_ctl(struct mtd_info *mtd, int cmd,
+ unsigned int ctrl)
+{
+ struct nand_chip *this = mtd->priv;
+ unsigned long nandaddr = (unsigned long)this->IO_ADDR_W;
+
+ if (cmd == NAND_CMD_NONE)
+ return;
+
+ if (ctrl & NAND_CLE)
+ writeb(cmd, PALMTX_NAND_CLE_VIRT);
+ else if (ctrl & NAND_ALE)
+ writeb(cmd, PALMTX_NAND_ALE_VIRT);
+ else
+ writeb(cmd, nandaddr);
+}
+
+static struct mtd_partition palmtx_partition_info[] = {
+ [0] = {
+ .name = "palmtx-0",
+ .offset = 0,
+ .size = MTDPART_SIZ_FULL
+ },
+};
+
+static const char *palmtx_part_probes[] = { "cmdlinepart", NULL };
+
+struct platform_nand_data palmtx_nand_platdata = {
+ .chip = {
+ .nr_chips = 1,
+ .chip_offset = 0,
+ .nr_partitions = ARRAY_SIZE(palmtx_partition_info),
+ .partitions = palmtx_partition_info,
+ .chip_delay = 20,
+ .part_probe_types = palmtx_part_probes,
+ },
+ .ctrl = {
+ .cmd_ctrl = palmtx_nand_cmd_ctl,
+ },
+};
+
+static struct resource palmtx_nand_resource[] = {
+ [0] = {
+ .start = PXA_CS1_PHYS,
+ .end = PXA_CS1_PHYS + SZ_1M - 1,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct platform_device palmtx_nand = {
+ .name = "gen_nand",
+ .num_resources = ARRAY_SIZE(palmtx_nand_resource),
+ .resource = palmtx_nand_resource,
+ .id = -1,
+ .dev = {
+ .platform_data = &palmtx_nand_platdata,
+ }
+};
+
/******************************************************************************
* Power management - standby
******************************************************************************/
&power_supply,
&palmtx_asoc,
&palmtx_gpio_vbus,
+ &palmtx_flash,
+ &palmtx_nand,
};
static struct map_desc palmtx_io_desc[] __initdata = {
.virtual = PALMTX_PCMCIA_VIRT,
.pfn = __phys_to_pfn(PALMTX_PCMCIA_PHYS),
.length = PALMTX_PCMCIA_SIZE,
- .type = MT_DEVICE
-},
+ .type = MT_DEVICE,
+}, {
+ .virtual = PALMTX_NAND_ALE_VIRT,
+ .pfn = __phys_to_pfn(PALMTX_NAND_ALE_PHYS),
+ .length = SZ_1M,
+ .type = MT_DEVICE,
+}, {
+ .virtual = PALMTX_NAND_CLE_VIRT,
+ .pfn = __phys_to_pfn(PALMTX_NAND_CLE_PHYS),
+ .length = SZ_1M,
+ .type = MT_DEVICE,
+}
};
static void __init palmtx_map_io(void)
/******************************************************************************
* SD/MMC card controller
******************************************************************************/
-static int palmz72_mci_init(struct device *dev,
- irq_handler_t palmz72_detect_int, void *data)
-{
- int err = 0;
-
- /* Setup an interrupt for detecting card insert/remove events */
- err = gpio_request(GPIO_NR_PALMZ72_SD_DETECT_N, "SD IRQ");
- if (err)
- goto err;
- err = gpio_direction_input(GPIO_NR_PALMZ72_SD_DETECT_N);
- if (err)
- goto err2;
- err = request_irq(gpio_to_irq(GPIO_NR_PALMZ72_SD_DETECT_N),
- palmz72_detect_int, IRQF_DISABLED | IRQF_SAMPLE_RANDOM |
- IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
- "SD/MMC card detect", data);
- if (err) {
- printk(KERN_ERR "%s: cannot request SD/MMC card detect IRQ\n",
- __func__);
- goto err2;
- }
-
- /* SD_POWER is not actually power, but it is more like chip
- * select, i.e. it is inverted */
-
- err = gpio_request(GPIO_NR_PALMZ72_SD_POWER_N, "SD_POWER");
- if (err)
- goto err3;
- err = gpio_direction_output(GPIO_NR_PALMZ72_SD_POWER_N, 0);
- if (err)
- goto err4;
- err = gpio_request(GPIO_NR_PALMZ72_SD_RO, "SD_RO");
- if (err)
- goto err4;
- err = gpio_direction_input(GPIO_NR_PALMZ72_SD_RO);
- if (err)
- goto err5;
-
- printk(KERN_DEBUG "%s: irq registered\n", __func__);
-
- return 0;
-
-err5:
- gpio_free(GPIO_NR_PALMZ72_SD_RO);
-err4:
- gpio_free(GPIO_NR_PALMZ72_SD_POWER_N);
-err3:
- free_irq(gpio_to_irq(GPIO_NR_PALMZ72_SD_DETECT_N), data);
-err2:
- gpio_free(GPIO_NR_PALMZ72_SD_DETECT_N);
-err:
- return err;
-}
-
-static void palmz72_mci_exit(struct device *dev, void *data)
-{
- gpio_free(GPIO_NR_PALMZ72_SD_POWER_N);
- free_irq(gpio_to_irq(GPIO_NR_PALMZ72_SD_DETECT_N), data);
- gpio_free(GPIO_NR_PALMZ72_SD_DETECT_N);
- gpio_free(GPIO_NR_PALMZ72_SD_RO);
-}
-
-static void palmz72_mci_power(struct device *dev, unsigned int vdd)
-{
- struct pxamci_platform_data *p_d = dev->platform_data;
- if (p_d->ocr_mask & (1 << vdd))
- gpio_set_value(GPIO_NR_PALMZ72_SD_POWER_N, 0);
- else
- gpio_set_value(GPIO_NR_PALMZ72_SD_POWER_N, 1);
-}
-
-static int palmz72_mci_ro(struct device *dev)
-{
- return gpio_get_value(GPIO_NR_PALMZ72_SD_RO);
-}
-
+/* SD_POWER is not actually power, but it is more like chip
+ * select, i.e. it is inverted */
static struct pxamci_platform_data palmz72_mci_platform_data = {
- .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
- .setpower = palmz72_mci_power,
- .get_ro = palmz72_mci_ro,
- .init = palmz72_mci_init,
- .exit = palmz72_mci_exit,
+ .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
+ .gpio_card_detect = GPIO_NR_PALMZ72_SD_DETECT_N,
+ .gpio_card_ro = GPIO_NR_PALMZ72_SD_RO,
+ .gpio_power = GPIO_NR_PALMZ72_SD_POWER_N,
+ .gpio_power_invert = 1,
};
/******************************************************************************
/******************************************************************************
* IrDA
******************************************************************************/
-static int palmz72_irda_startup(struct device *dev)
-{
- int err;
- err = gpio_request(GPIO_NR_PALMZ72_IR_DISABLE, "IR DISABLE");
- if (err)
- goto err;
- err = gpio_direction_output(GPIO_NR_PALMZ72_IR_DISABLE, 1);
- if (err)
- gpio_free(GPIO_NR_PALMZ72_IR_DISABLE);
-err:
- return err;
-}
-
-static void palmz72_irda_shutdown(struct device *dev)
-{
- gpio_free(GPIO_NR_PALMZ72_IR_DISABLE);
-}
-
-static void palmz72_irda_transceiver_mode(struct device *dev, int mode)
-{
- gpio_set_value(GPIO_NR_PALMZ72_IR_DISABLE, mode & IR_OFF);
- pxa2xx_transceiver_mode(dev, mode);
-}
-
static struct pxaficp_platform_data palmz72_ficp_platform_data = {
- .startup = palmz72_irda_startup,
- .shutdown = palmz72_irda_shutdown,
+ .gpio_pwdown = GPIO_NR_PALMZ72_IR_DISABLE,
.transceiver_cap = IR_SIRMODE | IR_OFF,
- .transceiver_mode = palmz72_irda_transceiver_mode,
};
/******************************************************************************
#define MSECS_PER_JIFFY (1000/HZ)
static struct pxamci_platform_data pcm990_mci_platform_data = {
- .detect_delay = 250 / MSECS_PER_JIFFY,
- .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
- .init = pcm990_mci_init,
- .setpower = pcm990_mci_setpower,
- .exit = pcm990_mci_exit,
+ .detect_delay = 250 / MSECS_PER_JIFFY,
+ .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
+ .init = pcm990_mci_init,
+ .setpower = pcm990_mci_setpower,
+ .exit = pcm990_mci_exit,
+ .gpio_card_detect = -1,
+ .gpio_card_ro = -1,
+ .gpio_power = -1,
};
static struct pxaohci_platform_data pcm990_ohci_platform_data = {
gpio_bus_switch = -EINVAL;
}
-static struct soc_camera_link iclink = {
- .bus_id = 0, /* Must match with the camera ID above */
- .query_bus_param = pcm990_camera_query_bus_param,
- .set_bus_param = pcm990_camera_set_bus_param,
- .free_bus = pcm990_camera_free_bus,
-};
-
/* Board I2C devices. */
static struct i2c_board_info __initdata pcm990_i2c_devices[] = {
{
/* Must initialize before the camera(s) */
I2C_BOARD_INFO("pca9536", 0x41),
.platform_data = &pca9536_data,
- }, {
+ },
+};
+
+static struct i2c_board_info pcm990_camera_i2c[] = {
+ {
I2C_BOARD_INFO("mt9v022", 0x48),
- .platform_data = &iclink, /* With extender */
}, {
I2C_BOARD_INFO("mt9m001", 0x5d),
- .platform_data = &iclink, /* With extender */
+ },
+};
+
+static struct soc_camera_link iclink[] = {
+ {
+ .bus_id = 0, /* Must match with the camera ID */
+ .board_info = &pcm990_camera_i2c[0],
+ .i2c_adapter_id = 0,
+ .query_bus_param = pcm990_camera_query_bus_param,
+ .set_bus_param = pcm990_camera_set_bus_param,
+ .free_bus = pcm990_camera_free_bus,
+ .module_name = "mt9v022",
+ }, {
+ .bus_id = 0, /* Must match with the camera ID */
+ .board_info = &pcm990_camera_i2c[1],
+ .i2c_adapter_id = 0,
+ .query_bus_param = pcm990_camera_query_bus_param,
+ .set_bus_param = pcm990_camera_set_bus_param,
+ .free_bus = pcm990_camera_free_bus,
+ .module_name = "mt9m001",
+ },
+};
+
+static struct platform_device pcm990_camera[] = {
+ {
+ .name = "soc-camera-pdrv",
+ .id = 0,
+ .dev = {
+ .platform_data = &iclink[0],
+ },
+ }, {
+ .name = "soc-camera-pdrv",
+ .id = 1,
+ .dev = {
+ .platform_data = &iclink[1],
+ },
},
};
#endif /* CONFIG_VIDEO_PXA27x ||CONFIG_VIDEO_PXA27x_MODULE */
pxa_set_camera_info(&pcm990_pxacamera_platform_data);
i2c_register_board_info(0, ARRAY_AND_SIZE(pcm990_i2c_devices));
+
+ platform_device_register(&pcm990_camera[0]);
+ platform_device_register(&pcm990_camera[1]);
#endif
printk(KERN_INFO "PCM-990 Evaluation baseboard initialized\n");
* The card detect interrupt isn't debounced so we delay it by 250ms
* to give the card a chance to fully insert/eject.
*/
-static struct pxamci_platform_data poodle_mci_platform_data;
-
static int poodle_mci_init(struct device *dev, irq_handler_t poodle_detect_int, void *data)
{
int err;
- err = gpio_request(POODLE_GPIO_nSD_DETECT, "nSD_DETECT");
- if (err)
- goto err_out;
-
- err = gpio_request(POODLE_GPIO_nSD_WP, "nSD_WP");
- if (err)
- goto err_free_1;
-
err = gpio_request(POODLE_GPIO_SD_PWR, "SD_PWR");
if (err)
goto err_free_2;
if (err)
goto err_free_3;
- gpio_direction_input(POODLE_GPIO_nSD_DETECT);
- gpio_direction_input(POODLE_GPIO_nSD_WP);
-
gpio_direction_output(POODLE_GPIO_SD_PWR, 0);
gpio_direction_output(POODLE_GPIO_SD_PWR1, 0);
- poodle_mci_platform_data.detect_delay = msecs_to_jiffies(250);
-
- err = request_irq(POODLE_IRQ_GPIO_nSD_DETECT, poodle_detect_int,
- IRQF_DISABLED | IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
- "MMC card detect", data);
- if (err) {
- pr_err("%s: MMC/SD: can't request MMC card detect IRQ\n",
- __func__);
- goto err_free_4;
- }
-
return 0;
-err_free_4:
- gpio_free(POODLE_GPIO_SD_PWR1);
err_free_3:
gpio_free(POODLE_GPIO_SD_PWR);
err_free_2:
- gpio_free(POODLE_GPIO_nSD_WP);
-err_free_1:
- gpio_free(POODLE_GPIO_nSD_DETECT);
-err_out:
return err;
}
}
}
-static int poodle_mci_get_ro(struct device *dev)
-{
- return !!gpio_get_value(POODLE_GPIO_nSD_WP);
- return GPLR(POODLE_GPIO_nSD_WP) & GPIO_bit(POODLE_GPIO_nSD_WP);
-}
-
-
static void poodle_mci_exit(struct device *dev, void *data)
{
- free_irq(POODLE_IRQ_GPIO_nSD_DETECT, data);
gpio_free(POODLE_GPIO_SD_PWR1);
gpio_free(POODLE_GPIO_SD_PWR);
- gpio_free(POODLE_GPIO_nSD_WP);
- gpio_free(POODLE_GPIO_nSD_DETECT);
}
static struct pxamci_platform_data poodle_mci_platform_data = {
- .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
- .init = poodle_mci_init,
- .get_ro = poodle_mci_get_ro,
- .setpower = poodle_mci_setpower,
- .exit = poodle_mci_exit,
+ .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
+ .init = poodle_mci_init,
+ .setpower = poodle_mci_setpower,
+ .exit = poodle_mci_exit,
+ .gpio_card_detect = POODLE_IRQ_GPIO_nSD_DETECT,
+ .gpio_card_ro = POODLE_GPIO_nSD_WP,
+ .gpio_power = -1,
};
/*
* Irda
*/
-static void poodle_irda_transceiver_mode(struct device *dev, int mode)
-{
- gpio_set_value(POODLE_GPIO_IR_ON, mode & IR_OFF);
- pxa2xx_transceiver_mode(dev, mode);
-}
-
-static int poodle_irda_startup(struct device *dev)
-{
- int err;
-
- err = gpio_request(POODLE_GPIO_IR_ON, "IR_ON");
- if (err)
- return err;
-
- gpio_direction_output(POODLE_GPIO_IR_ON, 1);
- return 0;
-}
-
-static void poodle_irda_shutdown(struct device *dev)
-{
- gpio_free(POODLE_GPIO_IR_ON);
-}
-
static struct pxaficp_platform_data poodle_ficp_platform_data = {
+ .gpio_pwdown = POODLE_GPIO_IR_ON,
.transceiver_cap = IR_SIRMODE | IR_OFF,
- .transceiver_mode = poodle_irda_transceiver_mode,
- .startup = poodle_irda_startup,
- .shutdown = poodle_irda_shutdown,
};
set_pxa_fb_parent(&poodle_locomo_device.dev);
set_pxa_fb_info(&poodle_fb_info);
pxa_set_udc_info(&udc_info);
+ poodle_mci_platform_data.detect_delay = msecs_to_jiffies(250);
pxa_set_mci_info(&poodle_mci_platform_data);
pxa_set_ficp_info(&poodle_ficp_platform_data);
pxa_set_i2c_info(NULL);
} else
BUG();
}
+EXPORT_SYMBOL_GPL(pxa2xx_transceiver_mode);
};
static DEFINE_PXA3_CKEN(common_nand, NAND, 156000000, 0);
+static DEFINE_PXA3_CKEN(gcu, PXA300_GCU, 0, 0);
static struct clk_lookup common_clkregs[] = {
INIT_CLKREG(&clk_common_nand, "pxa3xx-nand", NULL),
+ INIT_CLKREG(&clk_gcu, "pxa3xx-gcu", NULL),
};
static DEFINE_PXA3_CKEN(pxa310_mmc3, MMC3, 19500000, 0);
};
static DEFINE_PXA3_CKEN(pxa320_nand, NAND, 104000000, 0);
+static DEFINE_PXA3_CKEN(gcu, PXA320_GCU, 0, 0);
static struct clk_lookup pxa320_clkregs[] = {
INIT_CLKREG(&clk_pxa320_nand, "pxa3xx-nand", NULL),
+ INIT_CLKREG(&clk_gcu, "pxa3xx-gcu", NULL),
};
static int __init pxa320_init(void)
MFP_ADDR_END,
};
+static struct mfp_addr_map pxa935_mfp_addr_map[] __initdata = {
+ MFP_ADDR(GPIO159, 0x0524),
+ MFP_ADDR(GPIO163, 0x0534),
+ MFP_ADDR(GPIO167, 0x0544),
+ MFP_ADDR(GPIO168, 0x0548),
+ MFP_ADDR(GPIO169, 0x054c),
+ MFP_ADDR(GPIO170, 0x0550),
+ MFP_ADDR(GPIO171, 0x0554),
+ MFP_ADDR(GPIO172, 0x0558),
+ MFP_ADDR(GPIO173, 0x055c),
+
+ MFP_ADDR_END,
+};
+
static int __init pxa930_init(void)
{
- if (cpu_is_pxa930()) {
+ if (cpu_is_pxa930() || cpu_is_pxa935()) {
mfp_init_base(io_p2v(MFPR_BASE));
mfp_init_addr(pxa930_mfp_addr_map);
}
+ if (cpu_is_pxa935())
+ mfp_init_addr(pxa935_mfp_addr_map);
+
return 0;
}
#include <linux/spi/ads7846.h>
#include <linux/spi/corgi_lcd.h>
#include <linux/mtd/sharpsl.h>
+#include <linux/input/matrix_keypad.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
GPIO105_GPIO, /* SPITZ_GPIO_CF_IRQ */
GPIO106_GPIO, /* SPITZ_GPIO_CF2_IRQ */
+ /* GPIO matrix keypad */
+ GPIO88_GPIO, /* column 0 */
+ GPIO23_GPIO, /* column 1 */
+ GPIO24_GPIO, /* column 2 */
+ GPIO25_GPIO, /* column 3 */
+ GPIO26_GPIO, /* column 4 */
+ GPIO27_GPIO, /* column 5 */
+ GPIO52_GPIO, /* column 6 */
+ GPIO103_GPIO, /* column 7 */
+ GPIO107_GPIO, /* column 8 */
+ GPIO108_GPIO, /* column 9 */
+ GPIO114_GPIO, /* column 10 */
+ GPIO12_GPIO, /* row 0 */
+ GPIO17_GPIO, /* row 1 */
+ GPIO91_GPIO, /* row 2 */
+ GPIO34_GPIO, /* row 3 */
+ GPIO36_GPIO, /* row 4 */
+ GPIO38_GPIO, /* row 5 */
+ GPIO39_GPIO, /* row 6 */
+
/* I2C */
GPIO117_I2C_SCL,
GPIO118_I2C_SDA,
/*
* Spitz Keyboard Device
*/
+#define SPITZ_KEY_CALENDAR KEY_F1
+#define SPITZ_KEY_ADDRESS KEY_F2
+#define SPITZ_KEY_FN KEY_F3
+#define SPITZ_KEY_CANCEL KEY_F4
+#define SPITZ_KEY_EXOK KEY_F5
+#define SPITZ_KEY_EXCANCEL KEY_F6
+#define SPITZ_KEY_EXJOGDOWN KEY_F7
+#define SPITZ_KEY_EXJOGUP KEY_F8
+#define SPITZ_KEY_JAP1 KEY_LEFTALT
+#define SPITZ_KEY_JAP2 KEY_RIGHTCTRL
+#define SPITZ_KEY_SYNC KEY_F9
+#define SPITZ_KEY_MAIL KEY_F10
+#define SPITZ_KEY_OK KEY_F11
+#define SPITZ_KEY_MENU KEY_F12
+
+static const uint32_t spitzkbd_keymap[] = {
+ KEY(0, 0, KEY_LEFTCTRL),
+ KEY(0, 1, KEY_1),
+ KEY(0, 2, KEY_3),
+ KEY(0, 3, KEY_5),
+ KEY(0, 4, KEY_6),
+ KEY(0, 5, KEY_7),
+ KEY(0, 6, KEY_9),
+ KEY(0, 7, KEY_0),
+ KEY(0, 8, KEY_BACKSPACE),
+ KEY(0, 9, SPITZ_KEY_EXOK), /* EXOK */
+ KEY(0, 10, SPITZ_KEY_EXCANCEL), /* EXCANCEL */
+ KEY(1, 1, KEY_2),
+ KEY(1, 2, KEY_4),
+ KEY(1, 3, KEY_R),
+ KEY(1, 4, KEY_Y),
+ KEY(1, 5, KEY_8),
+ KEY(1, 6, KEY_I),
+ KEY(1, 7, KEY_O),
+ KEY(1, 8, KEY_P),
+ KEY(1, 9, SPITZ_KEY_EXJOGDOWN), /* EXJOGDOWN */
+ KEY(1, 10, SPITZ_KEY_EXJOGUP), /* EXJOGUP */
+ KEY(2, 0, KEY_TAB),
+ KEY(2, 1, KEY_Q),
+ KEY(2, 2, KEY_E),
+ KEY(2, 3, KEY_T),
+ KEY(2, 4, KEY_G),
+ KEY(2, 5, KEY_U),
+ KEY(2, 6, KEY_J),
+ KEY(2, 7, KEY_K),
+ KEY(3, 0, SPITZ_KEY_ADDRESS), /* ADDRESS */
+ KEY(3, 1, KEY_W),
+ KEY(3, 2, KEY_S),
+ KEY(3, 3, KEY_F),
+ KEY(3, 4, KEY_V),
+ KEY(3, 5, KEY_H),
+ KEY(3, 6, KEY_M),
+ KEY(3, 7, KEY_L),
+ KEY(3, 9, KEY_RIGHTSHIFT),
+ KEY(4, 0, SPITZ_KEY_CALENDAR), /* CALENDAR */
+ KEY(4, 1, KEY_A),
+ KEY(4, 2, KEY_D),
+ KEY(4, 3, KEY_C),
+ KEY(4, 4, KEY_B),
+ KEY(4, 5, KEY_N),
+ KEY(4, 6, KEY_DOT),
+ KEY(4, 8, KEY_ENTER),
+ KEY(4, 9, KEY_LEFTSHIFT),
+ KEY(5, 0, SPITZ_KEY_MAIL), /* MAIL */
+ KEY(5, 1, KEY_Z),
+ KEY(5, 2, KEY_X),
+ KEY(5, 3, KEY_MINUS),
+ KEY(5, 4, KEY_SPACE),
+ KEY(5, 5, KEY_COMMA),
+ KEY(5, 7, KEY_UP),
+ KEY(5, 10, SPITZ_KEY_FN), /* FN */
+ KEY(6, 0, KEY_SYSRQ),
+ KEY(6, 1, SPITZ_KEY_JAP1), /* JAP1 */
+ KEY(6, 2, SPITZ_KEY_JAP2), /* JAP2 */
+ KEY(6, 3, SPITZ_KEY_CANCEL), /* CANCEL */
+ KEY(6, 4, SPITZ_KEY_OK), /* OK */
+ KEY(6, 5, SPITZ_KEY_MENU), /* MENU */
+ KEY(6, 6, KEY_LEFT),
+ KEY(6, 7, KEY_DOWN),
+ KEY(6, 8, KEY_RIGHT),
+};
+
+static const struct matrix_keymap_data spitzkbd_keymap_data = {
+ .keymap = spitzkbd_keymap,
+ .keymap_size = ARRAY_SIZE(spitzkbd_keymap),
+};
+
+static const uint32_t spitzkbd_row_gpios[] =
+ { 12, 17, 91, 34, 36, 38, 39 };
+static const uint32_t spitzkbd_col_gpios[] =
+ { 88, 23, 24, 25, 26, 27, 52, 103, 107, 108, 114 };
+
+static struct matrix_keypad_platform_data spitzkbd_pdata = {
+ .keymap_data = &spitzkbd_keymap_data,
+ .row_gpios = spitzkbd_row_gpios,
+ .col_gpios = spitzkbd_col_gpios,
+ .num_row_gpios = ARRAY_SIZE(spitzkbd_row_gpios),
+ .num_col_gpios = ARRAY_SIZE(spitzkbd_col_gpios),
+ .col_scan_delay_us = 10,
+ .debounce_ms = 10,
+ .wakeup = 1,
+};
+
static struct platform_device spitzkbd_device = {
- .name = "spitz-keyboard",
+ .name = "matrix-keypad",
.id = -1,
+ .dev = {
+ .platform_data = &spitzkbd_pdata,
+ },
};
.vref_delay_usecs = 100,
.x_plate_ohms = 419,
.y_plate_ohms = 486,
+ .pressure_max = 1024,
.gpio_pendown = SPITZ_GPIO_TP_INT,
.wait_for_sync = spitz_wait_for_hsync,
};
* The card detect interrupt isn't debounced so we delay it by 250ms
* to give the card a chance to fully insert/eject.
*/
-
-static struct pxamci_platform_data spitz_mci_platform_data;
-
-static int spitz_mci_init(struct device *dev, irq_handler_t spitz_detect_int, void *data)
-{
- int err;
-
- err = gpio_request(SPITZ_GPIO_nSD_DETECT, "nSD_DETECT");
- if (err)
- goto err_out;
-
- err = gpio_request(SPITZ_GPIO_nSD_WP, "nSD_WP");
- if (err)
- goto err_free_1;
-
- gpio_direction_input(SPITZ_GPIO_nSD_DETECT);
- gpio_direction_input(SPITZ_GPIO_nSD_WP);
-
- spitz_mci_platform_data.detect_delay = msecs_to_jiffies(250);
-
- err = request_irq(SPITZ_IRQ_GPIO_nSD_DETECT, spitz_detect_int,
- IRQF_DISABLED | IRQF_TRIGGER_RISING |
- IRQF_TRIGGER_FALLING,
- "MMC card detect", data);
- if (err) {
- pr_err("%s: MMC/SD: can't request MMC card detect IRQ\n",
- __func__);
- goto err_free_2;
- }
- return 0;
-
-err_free_2:
- gpio_free(SPITZ_GPIO_nSD_WP);
-err_free_1:
- gpio_free(SPITZ_GPIO_nSD_DETECT);
-err_out:
- return err;
-}
-
static void spitz_mci_setpower(struct device *dev, unsigned int vdd)
{
struct pxamci_platform_data* p_d = dev->platform_data;
spitz_card_pwr_ctrl(SPITZ_PWR_SD, 0x0000);
}
-static int spitz_mci_get_ro(struct device *dev)
-{
- return gpio_get_value(SPITZ_GPIO_nSD_WP);
-}
-
-static void spitz_mci_exit(struct device *dev, void *data)
-{
- free_irq(SPITZ_IRQ_GPIO_nSD_DETECT, data);
- gpio_free(SPITZ_GPIO_nSD_WP);
- gpio_free(SPITZ_GPIO_nSD_DETECT);
-}
-
static struct pxamci_platform_data spitz_mci_platform_data = {
- .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
- .init = spitz_mci_init,
- .get_ro = spitz_mci_get_ro,
- .setpower = spitz_mci_setpower,
- .exit = spitz_mci_exit,
+ .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
+ .setpower = spitz_mci_setpower,
+ .gpio_card_detect = SPITZ_GPIO_nSD_DETECT,
+ .gpio_card_ro = SPITZ_GPIO_nSD_WP,
+ .gpio_power = -1,
};
/*
* Irda
*/
-static int spitz_irda_startup(struct device *dev)
-{
- int rc;
-
- rc = gpio_request(SPITZ_GPIO_IR_ON, "IrDA on");
- if (rc)
- goto err;
-
- rc = gpio_direction_output(SPITZ_GPIO_IR_ON, 1);
- if (rc)
- goto err_dir;
-
- return 0;
-
-err_dir:
- gpio_free(SPITZ_GPIO_IR_ON);
-err:
- return rc;
-}
-
-static void spitz_irda_shutdown(struct device *dev)
-{
- gpio_free(SPITZ_GPIO_IR_ON);
-}
-
-static void spitz_irda_transceiver_mode(struct device *dev, int mode)
-{
- gpio_set_value(SPITZ_GPIO_IR_ON, mode & IR_OFF);
- pxa2xx_transceiver_mode(dev, mode);
-}
-
-#ifdef CONFIG_MACH_AKITA
-static void akita_irda_transceiver_mode(struct device *dev, int mode)
-{
- gpio_set_value(AKITA_GPIO_IR_ON, mode & IR_OFF);
- pxa2xx_transceiver_mode(dev, mode);
-}
-#endif
static struct pxaficp_platform_data spitz_ficp_platform_data = {
+/* .gpio_pwdown is set in spitz_init() and akita_init() accordingly */
.transceiver_cap = IR_SIRMODE | IR_OFF,
- .transceiver_mode = spitz_irda_transceiver_mode,
- .startup = spitz_irda_startup,
- .shutdown = spitz_irda_shutdown,
};
spitz_init_spi();
platform_add_devices(devices, ARRAY_SIZE(devices));
+ spitz_mci_platform_data.detect_delay = msecs_to_jiffies(250);
pxa_set_mci_info(&spitz_mci_platform_data);
pxa_set_ohci_info(&spitz_ohci_platform_data);
pxa_set_ficp_info(&spitz_ficp_platform_data);
#if defined(CONFIG_MACH_SPITZ) || defined(CONFIG_MACH_BORZOI)
static void __init spitz_init(void)
{
+ spitz_ficp_platform_data.gpio_pwdown = SPITZ_GPIO_IR_ON;
+
platform_scoop_config = &spitz_pcmcia_config;
common_init();
static void __init akita_init(void)
{
- spitz_ficp_platform_data.transceiver_mode = akita_irda_transceiver_mode;
+ spitz_ficp_platform_data.gpio_pwdown = AKITA_GPIO_IR_ON;
sharpsl_nand_platform_data.badblock_pattern = &sharpsl_akita_bbt;
sharpsl_nand_platform_data.ecc_layout = &akita_oobinfo;
/*
* MMC/SD Device
*/
-static struct pxamci_platform_data tosa_mci_platform_data;
-
static int tosa_mci_init(struct device *dev, irq_handler_t tosa_detect_int, void *data)
{
int err;
- tosa_mci_platform_data.detect_delay = msecs_to_jiffies(250);
-
- err = gpio_request(TOSA_GPIO_nSD_DETECT, "MMC/SD card detect");
- if (err) {
- printk(KERN_ERR "tosa_mci_init: can't request nSD_DETECT gpio\n");
- goto err_gpio_detect;
- }
- err = gpio_direction_input(TOSA_GPIO_nSD_DETECT);
- if (err)
- goto err_gpio_detect_dir;
-
- err = request_irq(TOSA_IRQ_GPIO_nSD_DETECT, tosa_detect_int,
- IRQF_DISABLED | IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
- "MMC/SD card detect", data);
- if (err) {
- printk(KERN_ERR "tosa_mci_init: MMC/SD: can't request MMC card detect IRQ\n");
- goto err_irq;
- }
-
- err = gpio_request(TOSA_GPIO_SD_WP, "SD Write Protect");
- if (err) {
- printk(KERN_ERR "tosa_mci_init: can't request SD_WP gpio\n");
- goto err_gpio_wp;
- }
- err = gpio_direction_input(TOSA_GPIO_SD_WP);
- if (err)
- goto err_gpio_wp_dir;
-
- err = gpio_request(TOSA_GPIO_PWR_ON, "SD Power");
- if (err) {
- printk(KERN_ERR "tosa_mci_init: can't request SD_PWR gpio\n");
- goto err_gpio_pwr;
- }
- err = gpio_direction_output(TOSA_GPIO_PWR_ON, 0);
- if (err)
- goto err_gpio_pwr_dir;
-
err = gpio_request(TOSA_GPIO_nSD_INT, "SD Int");
if (err) {
printk(KERN_ERR "tosa_mci_init: can't request SD_PWR gpio\n");
err_gpio_int_dir:
gpio_free(TOSA_GPIO_nSD_INT);
err_gpio_int:
-err_gpio_pwr_dir:
- gpio_free(TOSA_GPIO_PWR_ON);
-err_gpio_pwr:
-err_gpio_wp_dir:
- gpio_free(TOSA_GPIO_SD_WP);
-err_gpio_wp:
- free_irq(TOSA_IRQ_GPIO_nSD_DETECT, data);
-err_irq:
-err_gpio_detect_dir:
- gpio_free(TOSA_GPIO_nSD_DETECT);
-err_gpio_detect:
return err;
}
-static void tosa_mci_setpower(struct device *dev, unsigned int vdd)
-{
- struct pxamci_platform_data* p_d = dev->platform_data;
-
- if (( 1 << vdd) & p_d->ocr_mask) {
- gpio_set_value(TOSA_GPIO_PWR_ON, 1);
- } else {
- gpio_set_value(TOSA_GPIO_PWR_ON, 0);
- }
-}
-
-static int tosa_mci_get_ro(struct device *dev)
-{
- return gpio_get_value(TOSA_GPIO_SD_WP);
-}
-
static void tosa_mci_exit(struct device *dev, void *data)
{
gpio_free(TOSA_GPIO_nSD_INT);
- gpio_free(TOSA_GPIO_PWR_ON);
- gpio_free(TOSA_GPIO_SD_WP);
- free_irq(TOSA_IRQ_GPIO_nSD_DETECT, data);
- gpio_free(TOSA_GPIO_nSD_DETECT);
}
static struct pxamci_platform_data tosa_mci_platform_data = {
- .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
- .init = tosa_mci_init,
- .get_ro = tosa_mci_get_ro,
- .setpower = tosa_mci_setpower,
- .exit = tosa_mci_exit,
+ .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
+ .init = tosa_mci_init,
+ .exit = tosa_mci_exit,
+ .gpio_card_detect = TOSA_GPIO_nSD_DETECT,
+ .gpio_card_ro = TOSA_GPIO_SD_WP,
+ .gpio_power = TOSA_GPIO_PWR_ON,
};
/*
}
static struct pxaficp_platform_data tosa_ficp_platform_data = {
- .transceiver_cap = IR_SIRMODE | IR_OFF,
- .transceiver_mode = tosa_irda_transceiver_mode,
- .startup = tosa_irda_startup,
- .shutdown = tosa_irda_shutdown,
+ .gpio_pwdown = -1,
+ .transceiver_cap = IR_SIRMODE | IR_OFF,
+ .transceiver_mode = tosa_irda_transceiver_mode,
+ .startup = tosa_irda_startup,
+ .shutdown = tosa_irda_shutdown,
};
/*
dummy = gpiochip_reserve(TOSA_SCOOP_JC_GPIO_BASE, 12);
dummy = gpiochip_reserve(TOSA_TC6393XB_GPIO_BASE, 16);
+ tosa_mci_platform_data.detect_delay = msecs_to_jiffies(250);
pxa_set_mci_info(&tosa_mci_platform_data);
pxa_set_udc_info(&udc_info);
pxa_set_ficp_info(&tosa_ficp_platform_data);
/******************************************************************************
* SD/MMC card controller
******************************************************************************/
-static int treo680_mci_init(struct device *dev,
- irq_handler_t treo680_detect_int, void *data)
-{
- int err = 0;
-
- /* Setup an interrupt for detecting card insert/remove events */
- err = gpio_request(GPIO_NR_TREO680_SD_DETECT_N, "SD IRQ");
-
- if (err)
- goto err;
-
- err = gpio_direction_input(GPIO_NR_TREO680_SD_DETECT_N);
- if (err)
- goto err2;
-
- err = request_irq(gpio_to_irq(GPIO_NR_TREO680_SD_DETECT_N),
- treo680_detect_int, IRQF_DISABLED | IRQF_SAMPLE_RANDOM |
- IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
- "SD/MMC card detect", data);
-
- if (err) {
- dev_err(dev, "%s: cannot request SD/MMC card detect IRQ\n",
- __func__);
- goto err2;
- }
-
- err = gpio_request(GPIO_NR_TREO680_SD_POWER, "SD_POWER");
- if (err)
- goto err3;
-
- err = gpio_direction_output(GPIO_NR_TREO680_SD_POWER, 1);
- if (err)
- goto err4;
-
- err = gpio_request(GPIO_NR_TREO680_SD_READONLY, "SD_READONLY");
- if (err)
- goto err4;
-
- err = gpio_direction_input(GPIO_NR_TREO680_SD_READONLY);
- if (err)
- goto err5;
-
- return 0;
-
-err5:
- gpio_free(GPIO_NR_TREO680_SD_READONLY);
-err4:
- gpio_free(GPIO_NR_TREO680_SD_POWER);
-err3:
- free_irq(gpio_to_irq(GPIO_NR_TREO680_SD_DETECT_N), data);
-err2:
- gpio_free(GPIO_NR_TREO680_SD_DETECT_N);
-err:
- return err;
-}
-
-static void treo680_mci_exit(struct device *dev, void *data)
-{
- gpio_free(GPIO_NR_TREO680_SD_READONLY);
- gpio_free(GPIO_NR_TREO680_SD_POWER);
- free_irq(gpio_to_irq(GPIO_NR_TREO680_SD_DETECT_N), data);
- gpio_free(GPIO_NR_TREO680_SD_DETECT_N);
-}
-
-static void treo680_mci_power(struct device *dev, unsigned int vdd)
-{
- struct pxamci_platform_data *p_d = dev->platform_data;
- gpio_set_value(GPIO_NR_TREO680_SD_POWER, p_d->ocr_mask & (1 << vdd));
-}
-
-static int treo680_mci_get_ro(struct device *dev)
-{
- return gpio_get_value(GPIO_NR_TREO680_SD_READONLY);
-}
-
static struct pxamci_platform_data treo680_mci_platform_data = {
- .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
- .setpower = treo680_mci_power,
- .get_ro = treo680_mci_get_ro,
- .init = treo680_mci_init,
- .exit = treo680_mci_exit,
+ .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
+ .gpio_card_detect = GPIO_NR_TREO680_SD_DETECT_N,
+ .gpio_card_ro = GPIO_NR_TREO680_SD_READONLY,
+ .gpio_power = GPIO_NR_TREO680_SD_POWER,
};
/******************************************************************************
ret = gpio_direction_output(GPIO_NR_TREO680_BL_POWER, 0);
if (ret)
goto err2;
- ret = gpio_request(GPIO_NR_TREO680_LCD_POWER, "LCD POWER");
- if (ret)
- goto err2;
- ret = gpio_direction_output(GPIO_NR_TREO680_LCD_POWER, 0);
- if (ret)
- goto err3;
return 0;
-err3:
- gpio_free(GPIO_NR_TREO680_LCD_POWER);
+
err2:
gpio_free(GPIO_NR_TREO680_BL_POWER);
err:
static void treo680_backlight_exit(struct device *dev)
{
gpio_free(GPIO_NR_TREO680_BL_POWER);
- gpio_free(GPIO_NR_TREO680_LCD_POWER);
}
static struct platform_pwm_backlight_data treo680_backlight_data = {
/******************************************************************************
* IrDA
******************************************************************************/
-static void treo680_transceiver_mode(struct device *dev, int mode)
-{
- gpio_set_value(GPIO_NR_TREO680_IR_EN, mode & IR_OFF);
- pxa2xx_transceiver_mode(dev, mode);
-}
-
-static int treo680_irda_startup(struct device *dev)
-{
- int err;
-
- err = gpio_request(GPIO_NR_TREO680_IR_EN, "Ir port disable");
- if (err)
- goto err1;
-
- err = gpio_direction_output(GPIO_NR_TREO680_IR_EN, 1);
- if (err)
- goto err2;
-
- return 0;
-
-err2:
- dev_err(dev, "treo680_irda: cannot change IR gpio direction\n");
- gpio_free(GPIO_NR_TREO680_IR_EN);
-err1:
- dev_err(dev, "treo680_irda: cannot allocate IR gpio\n");
- return err;
-}
-
-static void treo680_irda_shutdown(struct device *dev)
-{
- gpio_free(GPIO_NR_TREO680_IR_EN);
-}
-
static struct pxaficp_platform_data treo680_ficp_info = {
- .transceiver_cap = IR_FIRMODE | IR_SIRMODE | IR_OFF,
- .startup = treo680_irda_startup,
- .shutdown = treo680_irda_shutdown,
- .transceiver_mode = treo680_transceiver_mode,
+ .gpio_pwdown = GPIO_NR_TREO680_IR_EN,
+ .transceiver_cap = IR_SIRMODE | IR_OFF,
};
/******************************************************************************
},
};
+static void treo680_lcd_power(int on, struct fb_var_screeninfo *info)
+{
+ gpio_set_value(GPIO_NR_TREO680_BL_POWER, on);
+}
+
static struct pxafb_mach_info treo680_lcd_screen = {
.modes = treo680_lcd_modes,
.num_modes = ARRAY_SIZE(treo680_lcd_modes),
}
}
+static void __init treo680_lcd_power_init(void)
+{
+ int ret;
+
+ ret = gpio_request(GPIO_NR_TREO680_LCD_POWER, "LCD POWER");
+ if (ret) {
+ pr_err("Treo680: LCD power GPIO request failed!\n");
+ return;
+ }
+
+ ret = gpio_direction_output(GPIO_NR_TREO680_LCD_POWER, 0);
+ if (ret) {
+ pr_err("Treo680: setting LCD power GPIO direction failed!\n");
+ gpio_free(GPIO_NR_TREO680_LCD_POWER);
+ return;
+ }
+
+ treo680_lcd_screen.pxafb_lcd_power = treo680_lcd_power;
+}
+
static void __init treo680_init(void)
{
treo680_pm_init();
pxa2xx_mfp_config(ARRAY_AND_SIZE(treo680_pin_config));
pxa_set_keypad_info(&treo680_keypad_platform_data);
+ treo680_lcd_power_init();
set_pxa_fb_info(&treo680_lcd_screen);
pxa_set_mci_info(&treo680_mci_platform_data);
treo680_udc_init();
.exit = trizeps4_mci_exit,
.get_ro = NULL, /* write-protection not supported */
.setpower = NULL, /* power-switching not supported */
+ .gpio_card_detect = -1,
+ .gpio_card_ro = -1,
+ .gpio_power = -1,
};
/****************************************************************************
}
static struct pxaficp_platform_data trizeps4_ficp_platform_data = {
+ .gpio_pwdown = -1,
.transceiver_cap = IR_SIRMODE | IR_FIRMODE | IR_OFF,
.transceiver_mode = trizeps4_irda_transceiver_mode,
.startup = trizeps4_irda_startup,
--- /dev/null
+/* linux/arch/arm/mach-pxa/xcep.c
+ *
+ * Support for the Iskratel Electronics XCEP platform as used in
+ * the Libera instruments from Instrumentation Technologies.
+ *
+ * Author: Ales Bardorfer <ales@i-tech.si>
+ * Contributions by: Abbott, MG (Michael) <michael.abbott@diamond.ac.uk>
+ * Contributions by: Matej Kenda <matej.kenda@i-tech.si>
+ * Created: June 2006
+ * Copyright: (C) 2006-2009 Instrumentation Technologies
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/platform_device.h>
+#include <linux/i2c.h>
+#include <linux/smc91x.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/physmap.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/irq.h>
+#include <asm/mach/map.h>
+
+#include <plat/i2c.h>
+
+#include <mach/hardware.h>
+#include <mach/pxa2xx-regs.h>
+#include <mach/mfp-pxa25x.h>
+
+#include "generic.h"
+
+#define XCEP_ETH_PHYS (PXA_CS3_PHYS + 0x00000300)
+#define XCEP_ETH_PHYS_END (PXA_CS3_PHYS + 0x000fffff)
+#define XCEP_ETH_ATTR (PXA_CS3_PHYS + 0x02000000)
+#define XCEP_ETH_ATTR_END (PXA_CS3_PHYS + 0x020fffff)
+#define XCEP_ETH_IRQ IRQ_GPIO0
+
+/* XCEP CPLD base */
+#define XCEP_CPLD_BASE 0xf0000000
+
+
+/* Flash partitions. */
+
+static struct mtd_partition xcep_partitions[] = {
+ {
+ .name = "Bootloader",
+ .size = 0x00040000,
+ .offset = 0,
+ .mask_flags = MTD_WRITEABLE
+ }, {
+ .name = "Bootloader ENV",
+ .size = 0x00040000,
+ .offset = 0x00040000,
+ .mask_flags = MTD_WRITEABLE
+ }, {
+ .name = "Kernel",
+ .size = 0x00100000,
+ .offset = 0x00080000,
+ }, {
+ .name = "Rescue fs",
+ .size = 0x00280000,
+ .offset = 0x00180000,
+ }, {
+ .name = "Filesystem",
+ .size = MTDPART_SIZ_FULL,
+ .offset = 0x00400000
+ }
+};
+
+static struct physmap_flash_data xcep_flash_data[] = {
+ {
+ .width = 4, /* bankwidth in bytes */
+ .parts = xcep_partitions,
+ .nr_parts = ARRAY_SIZE(xcep_partitions)
+ }
+};
+
+static struct resource flash_resource = {
+ .start = PXA_CS0_PHYS,
+ .end = PXA_CS0_PHYS + SZ_32M - 1,
+ .flags = IORESOURCE_MEM,
+};
+
+static struct platform_device flash_device = {
+ .name = "physmap-flash",
+ .id = 0,
+ .dev = {
+ .platform_data = xcep_flash_data,
+ },
+ .resource = &flash_resource,
+ .num_resources = 1,
+};
+
+
+
+/* SMC LAN91C111 network controller. */
+
+static struct resource smc91x_resources[] = {
+ [0] = {
+ .name = "smc91x-regs",
+ .start = XCEP_ETH_PHYS,
+ .end = XCEP_ETH_PHYS_END,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = XCEP_ETH_IRQ,
+ .end = XCEP_ETH_IRQ,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .name = "smc91x-attrib",
+ .start = XCEP_ETH_ATTR,
+ .end = XCEP_ETH_ATTR_END,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct smc91x_platdata xcep_smc91x_info = {
+ .flags = SMC91X_USE_32BIT | SMC91X_NOWAIT | SMC91X_USE_DMA,
+};
+
+static struct platform_device smc91x_device = {
+ .name = "smc91x",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(smc91x_resources),
+ .resource = smc91x_resources,
+ .dev = {
+ .platform_data = &xcep_smc91x_info,
+ },
+};
+
+
+static struct platform_device *devices[] __initdata = {
+ &flash_device,
+ &smc91x_device,
+};
+
+
+/* We have to state that there are HWMON devices on the I2C bus on XCEP.
+ * Drivers for HWMON verify capabilities of the adapter when loading and
+ * refuse to attach if the adapter doesn't support HWMON class of devices.
+ * See also Documentation/i2c/porting-clients. */
+static struct i2c_pxa_platform_data xcep_i2c_platform_data = {
+ .class = I2C_CLASS_HWMON
+};
+
+
+static mfp_cfg_t xcep_pin_config[] __initdata = {
+ GPIO79_nCS_3, /* SMC 91C111 chip select. */
+ GPIO80_nCS_4, /* CPLD chip select. */
+ /* SSP communication to MSP430 */
+ GPIO23_SSP1_SCLK,
+ GPIO24_SSP1_SFRM,
+ GPIO25_SSP1_TXD,
+ GPIO26_SSP1_RXD,
+ GPIO27_SSP1_EXTCLK
+};
+
+static void __init xcep_init(void)
+{
+ pxa2xx_mfp_config(ARRAY_AND_SIZE(xcep_pin_config));
+
+ /* See Intel XScale Developer's Guide for details */
+ /* Set RDF and RDN to appropriate values (chip select 3 (smc91x)) */
+ MSC1 = (MSC1 & 0xffff) | 0xD5540000;
+ /* Set RDF and RDN to appropriate values (chip select 5 (fpga)) */
+ MSC2 = (MSC2 & 0xffff) | 0x72A00000;
+
+ platform_add_devices(ARRAY_AND_SIZE(devices));
+ pxa_set_i2c_info(&xcep_i2c_platform_data);
+}
+
+MACHINE_START(XCEP, "Iskratel XCEP")
+ .phys_io = 0x40000000,
+ .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc,
+ .boot_params = 0xa0000100,
+ .init_machine = xcep_init,
+ .map_io = pxa_map_io,
+ .init_irq = pxa25x_init_irq,
+ .timer = &pxa_timer,
+MACHINE_END
+
.init = zylonite_mci_init,
.exit = zylonite_mci_exit,
.get_ro = zylonite_mci_ro,
+ .gpio_card_detect = -1,
+ .gpio_card_ro = -1,
+ .gpio_power = -1,
};
static struct pxamci_platform_data zylonite_mci2_platform_data = {
#include <linux/io.h>
#include <linux/smsc911x.h>
#include <linux/ata_platform.h>
+#include <linux/amba/mmci.h>
#include <asm/clkdev.h>
#include <asm/system.h>
#include <asm/mach/flash.h>
#include <asm/mach/irq.h>
#include <asm/mach/map.h>
-#include <asm/mach/mmc.h>
#include <asm/hardware/gic.h>
return readl(REALVIEW_SYSMCI) & mask;
}
-struct mmc_platform_data realview_mmc0_plat_data = {
+struct mmci_platform_data realview_mmc0_plat_data = {
.ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
.status = realview_mmc_status,
.gpio_wp = 17,
.gpio_cd = 16,
};
-struct mmc_platform_data realview_mmc1_plat_data = {
+struct mmci_platform_data realview_mmc1_plat_data = {
.ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
.status = realview_mmc_status,
.gpio_wp = 19,
static struct clk_lookup lookups[] = {
{ /* UART0 */
- .dev_id = "dev:f1",
+ .dev_id = "dev:uart0",
.clk = &ref24_clk,
}, { /* UART1 */
- .dev_id = "dev:f2",
+ .dev_id = "dev:uart1",
.clk = &ref24_clk,
}, { /* UART2 */
- .dev_id = "dev:f3",
+ .dev_id = "dev:uart2",
.clk = &ref24_clk,
}, { /* UART3 */
- .dev_id = "fpga:09",
+ .dev_id = "fpga:uart3",
.clk = &ref24_clk,
}, { /* KMI0 */
- .dev_id = "fpga:06",
+ .dev_id = "fpga:kmi0",
.clk = &ref24_clk,
}, { /* KMI1 */
- .dev_id = "fpga:07",
+ .dev_id = "fpga:kmi1",
.clk = &ref24_clk,
}, { /* MMC0 */
- .dev_id = "fpga:05",
+ .dev_id = "fpga:mmc0",
.clk = &ref24_clk,
}, { /* EB:CLCD */
- .dev_id = "dev:20",
+ .dev_id = "dev:clcd",
.clk = &oscvco_clk,
}, { /* PB:CLCD */
- .dev_id = "issp:20",
+ .dev_id = "issp:clcd",
.clk = &oscvco_clk,
}
};
extern struct platform_device realview_flash_device;
extern struct platform_device realview_cf_device;
extern struct platform_device realview_i2c_device;
-extern struct mmc_platform_data realview_mmc0_plat_data;
-extern struct mmc_platform_data realview_mmc1_plat_data;
+extern struct mmci_platform_data realview_mmc0_plat_data;
+extern struct mmci_platform_data realview_mmc1_plat_data;
extern struct clcd_board clcd_plat_data;
extern void __iomem *gic_cpu_base_addr;
extern void __iomem *timer0_va_base;
#include <linux/sysdev.h>
#include <linux/amba/bus.h>
#include <linux/amba/pl061.h>
+#include <linux/amba/mmci.h>
#include <linux/io.h>
#include <mach/hardware.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <asm/mach/mmc.h>
#include <asm/mach/time.h>
#include <mach/board-eb.h>
#define EB_SSP_DMA { 9, 8 }
/* FPGA Primecells */
-AMBA_DEVICE(aaci, "fpga:04", AACI, NULL);
-AMBA_DEVICE(mmc0, "fpga:05", MMCI0, &realview_mmc0_plat_data);
-AMBA_DEVICE(kmi0, "fpga:06", KMI0, NULL);
-AMBA_DEVICE(kmi1, "fpga:07", KMI1, NULL);
-AMBA_DEVICE(uart3, "fpga:09", EB_UART3, NULL);
+AMBA_DEVICE(aaci, "fpga:aaci", AACI, NULL);
+AMBA_DEVICE(mmc0, "fpga:mmc0", MMCI0, &realview_mmc0_plat_data);
+AMBA_DEVICE(kmi0, "fpga:kmi0", KMI0, NULL);
+AMBA_DEVICE(kmi1, "fpga:kmi1", KMI1, NULL);
+AMBA_DEVICE(uart3, "fpga:uart3", EB_UART3, NULL);
/* DevChip Primecells */
-AMBA_DEVICE(smc, "dev:00", EB_SMC, NULL);
-AMBA_DEVICE(clcd, "dev:20", EB_CLCD, &clcd_plat_data);
-AMBA_DEVICE(dmac, "dev:30", DMAC, NULL);
-AMBA_DEVICE(sctl, "dev:e0", SCTL, NULL);
-AMBA_DEVICE(wdog, "dev:e1", EB_WATCHDOG, NULL);
-AMBA_DEVICE(gpio0, "dev:e4", EB_GPIO0, &gpio0_plat_data);
-AMBA_DEVICE(gpio1, "dev:e5", GPIO1, &gpio1_plat_data);
-AMBA_DEVICE(gpio2, "dev:e6", GPIO2, &gpio2_plat_data);
-AMBA_DEVICE(rtc, "dev:e8", EB_RTC, NULL);
-AMBA_DEVICE(sci0, "dev:f0", SCI, NULL);
-AMBA_DEVICE(uart0, "dev:f1", EB_UART0, NULL);
-AMBA_DEVICE(uart1, "dev:f2", EB_UART1, NULL);
-AMBA_DEVICE(uart2, "dev:f3", EB_UART2, NULL);
-AMBA_DEVICE(ssp0, "dev:f4", EB_SSP, NULL);
+AMBA_DEVICE(smc, "dev:smc", EB_SMC, NULL);
+AMBA_DEVICE(clcd, "dev:clcd", EB_CLCD, &clcd_plat_data);
+AMBA_DEVICE(dmac, "dev:dmac", DMAC, NULL);
+AMBA_DEVICE(sctl, "dev:sctl", SCTL, NULL);
+AMBA_DEVICE(wdog, "dev:wdog", EB_WATCHDOG, NULL);
+AMBA_DEVICE(gpio0, "dev:gpio0", EB_GPIO0, &gpio0_plat_data);
+AMBA_DEVICE(gpio1, "dev:gpio1", GPIO1, &gpio1_plat_data);
+AMBA_DEVICE(gpio2, "dev:gpio2", GPIO2, &gpio2_plat_data);
+AMBA_DEVICE(rtc, "dev:rtc", EB_RTC, NULL);
+AMBA_DEVICE(sci0, "dev:sci0", SCI, NULL);
+AMBA_DEVICE(uart0, "dev:uart0", EB_UART0, NULL);
+AMBA_DEVICE(uart1, "dev:uart1", EB_UART1, NULL);
+AMBA_DEVICE(uart2, "dev:uart2", EB_UART2, NULL);
+AMBA_DEVICE(ssp0, "dev:ssp0", EB_SSP, NULL);
static struct amba_device *amba_devs[] __initdata = {
&dmac_device,
#include <linux/sysdev.h>
#include <linux/amba/bus.h>
#include <linux/amba/pl061.h>
+#include <linux/amba/mmci.h>
#include <linux/io.h>
#include <mach/hardware.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
#include <asm/mach/map.h>
-#include <asm/mach/mmc.h>
#include <asm/mach/time.h>
#include <mach/board-pb1176.h>
#define PB1176_SSP_DMA { 9, 8 }
/* FPGA Primecells */
-AMBA_DEVICE(aaci, "fpga:04", AACI, NULL);
-AMBA_DEVICE(mmc0, "fpga:05", MMCI0, &realview_mmc0_plat_data);
-AMBA_DEVICE(kmi0, "fpga:06", KMI0, NULL);
-AMBA_DEVICE(kmi1, "fpga:07", KMI1, NULL);
-AMBA_DEVICE(uart3, "fpga:09", PB1176_UART3, NULL);
+AMBA_DEVICE(aaci, "fpga:aaci", AACI, NULL);
+AMBA_DEVICE(mmc0, "fpga:mmc0", MMCI0, &realview_mmc0_plat_data);
+AMBA_DEVICE(kmi0, "fpga:kmi0", KMI0, NULL);
+AMBA_DEVICE(kmi1, "fpga:kmi1", KMI1, NULL);
+AMBA_DEVICE(uart3, "fpga:uart3", PB1176_UART3, NULL);
/* DevChip Primecells */
-AMBA_DEVICE(smc, "dev:00", PB1176_SMC, NULL);
-AMBA_DEVICE(sctl, "dev:e0", SCTL, NULL);
-AMBA_DEVICE(wdog, "dev:e1", PB1176_WATCHDOG, NULL);
-AMBA_DEVICE(gpio0, "dev:e4", PB1176_GPIO0, &gpio0_plat_data);
-AMBA_DEVICE(gpio1, "dev:e5", GPIO1, &gpio1_plat_data);
-AMBA_DEVICE(gpio2, "dev:e6", GPIO2, &gpio2_plat_data);
-AMBA_DEVICE(rtc, "dev:e8", PB1176_RTC, NULL);
-AMBA_DEVICE(sci0, "dev:f0", SCI, NULL);
-AMBA_DEVICE(uart0, "dev:f1", PB1176_UART0, NULL);
-AMBA_DEVICE(uart1, "dev:f2", PB1176_UART1, NULL);
-AMBA_DEVICE(uart2, "dev:f3", PB1176_UART2, NULL);
-AMBA_DEVICE(ssp0, "dev:f4", PB1176_SSP, NULL);
+AMBA_DEVICE(smc, "dev:smc", PB1176_SMC, NULL);
+AMBA_DEVICE(sctl, "dev:sctl", SCTL, NULL);
+AMBA_DEVICE(wdog, "dev:wdog", PB1176_WATCHDOG, NULL);
+AMBA_DEVICE(gpio0, "dev:gpio0", PB1176_GPIO0, &gpio0_plat_data);
+AMBA_DEVICE(gpio1, "dev:gpio1", GPIO1, &gpio1_plat_data);
+AMBA_DEVICE(gpio2, "dev:gpio2", GPIO2, &gpio2_plat_data);
+AMBA_DEVICE(rtc, "dev:rtc", PB1176_RTC, NULL);
+AMBA_DEVICE(sci0, "dev:sci0", SCI, NULL);
+AMBA_DEVICE(uart0, "dev:uart0", PB1176_UART0, NULL);
+AMBA_DEVICE(uart1, "dev:uart1", PB1176_UART1, NULL);
+AMBA_DEVICE(uart2, "dev:uart2", PB1176_UART2, NULL);
+AMBA_DEVICE(ssp0, "dev:ssp0", PB1176_SSP, NULL);
/* Primecells on the NEC ISSP chip */
-AMBA_DEVICE(clcd, "issp:20", PB1176_CLCD, &clcd_plat_data);
-//AMBA_DEVICE(dmac, "issp:30", PB1176_DMAC, NULL);
+AMBA_DEVICE(clcd, "issp:clcd", PB1176_CLCD, &clcd_plat_data);
+//AMBA_DEVICE(dmac, "issp:dmac", PB1176_DMAC, NULL);
static struct amba_device *amba_devs[] __initdata = {
// &dmac_device,
#include <linux/sysdev.h>
#include <linux/amba/bus.h>
#include <linux/amba/pl061.h>
+#include <linux/amba/mmci.h>
#include <linux/io.h>
#include <mach/hardware.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
#include <asm/mach/map.h>
-#include <asm/mach/mmc.h>
#include <asm/mach/time.h>
#include <mach/board-pb11mp.h>
#define PB11MP_SSP_DMA { 9, 8 }
/* FPGA Primecells */
-AMBA_DEVICE(aaci, "fpga:04", AACI, NULL);
-AMBA_DEVICE(mmc0, "fpga:05", MMCI0, &realview_mmc0_plat_data);
-AMBA_DEVICE(kmi0, "fpga:06", KMI0, NULL);
-AMBA_DEVICE(kmi1, "fpga:07", KMI1, NULL);
-AMBA_DEVICE(uart3, "fpga:09", PB11MP_UART3, NULL);
+AMBA_DEVICE(aaci, "fpga:aaci", AACI, NULL);
+AMBA_DEVICE(mmc0, "fpga:mmc0", MMCI0, &realview_mmc0_plat_data);
+AMBA_DEVICE(kmi0, "fpga:kmi0", KMI0, NULL);
+AMBA_DEVICE(kmi1, "fpga:kmi1", KMI1, NULL);
+AMBA_DEVICE(uart3, "fpga:uart3", PB11MP_UART3, NULL);
/* DevChip Primecells */
-AMBA_DEVICE(smc, "dev:00", PB11MP_SMC, NULL);
-AMBA_DEVICE(sctl, "dev:e0", SCTL, NULL);
-AMBA_DEVICE(wdog, "dev:e1", PB11MP_WATCHDOG, NULL);
-AMBA_DEVICE(gpio0, "dev:e4", PB11MP_GPIO0, &gpio0_plat_data);
-AMBA_DEVICE(gpio1, "dev:e5", GPIO1, &gpio1_plat_data);
-AMBA_DEVICE(gpio2, "dev:e6", GPIO2, &gpio2_plat_data);
-AMBA_DEVICE(rtc, "dev:e8", PB11MP_RTC, NULL);
-AMBA_DEVICE(sci0, "dev:f0", SCI, NULL);
-AMBA_DEVICE(uart0, "dev:f1", PB11MP_UART0, NULL);
-AMBA_DEVICE(uart1, "dev:f2", PB11MP_UART1, NULL);
-AMBA_DEVICE(uart2, "dev:f3", PB11MP_UART2, NULL);
-AMBA_DEVICE(ssp0, "dev:f4", PB11MP_SSP, NULL);
+AMBA_DEVICE(smc, "dev:smc", PB11MP_SMC, NULL);
+AMBA_DEVICE(sctl, "dev:sctl", SCTL, NULL);
+AMBA_DEVICE(wdog, "dev:wdog", PB11MP_WATCHDOG, NULL);
+AMBA_DEVICE(gpio0, "dev:gpio0", PB11MP_GPIO0, &gpio0_plat_data);
+AMBA_DEVICE(gpio1, "dev:gpio1", GPIO1, &gpio1_plat_data);
+AMBA_DEVICE(gpio2, "dev:gpio2", GPIO2, &gpio2_plat_data);
+AMBA_DEVICE(rtc, "dev:rtc", PB11MP_RTC, NULL);
+AMBA_DEVICE(sci0, "dev:sci0", SCI, NULL);
+AMBA_DEVICE(uart0, "dev:uart0", PB11MP_UART0, NULL);
+AMBA_DEVICE(uart1, "dev:uart1", PB11MP_UART1, NULL);
+AMBA_DEVICE(uart2, "dev:uart2", PB11MP_UART2, NULL);
+AMBA_DEVICE(ssp0, "dev:ssp0", PB11MP_SSP, NULL);
/* Primecells on the NEC ISSP chip */
-AMBA_DEVICE(clcd, "issp:20", PB11MP_CLCD, &clcd_plat_data);
-AMBA_DEVICE(dmac, "issp:30", DMAC, NULL);
+AMBA_DEVICE(clcd, "issp:clcd", PB11MP_CLCD, &clcd_plat_data);
+AMBA_DEVICE(dmac, "issp:dmac", DMAC, NULL);
static struct amba_device *amba_devs[] __initdata = {
&dmac_device,
#include <linux/sysdev.h>
#include <linux/amba/bus.h>
#include <linux/amba/pl061.h>
+#include <linux/amba/mmci.h>
#include <linux/io.h>
#include <asm/irq.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <asm/mach/mmc.h>
#include <asm/mach/time.h>
#include <mach/hardware.h>
#define PBA8_SSP_DMA { 9, 8 }
/* FPGA Primecells */
-AMBA_DEVICE(aaci, "fpga:04", AACI, NULL);
-AMBA_DEVICE(mmc0, "fpga:05", MMCI0, &realview_mmc0_plat_data);
-AMBA_DEVICE(kmi0, "fpga:06", KMI0, NULL);
-AMBA_DEVICE(kmi1, "fpga:07", KMI1, NULL);
-AMBA_DEVICE(uart3, "fpga:09", PBA8_UART3, NULL);
+AMBA_DEVICE(aaci, "fpga:aaci", AACI, NULL);
+AMBA_DEVICE(mmc0, "fpga:mmc0", MMCI0, &realview_mmc0_plat_data);
+AMBA_DEVICE(kmi0, "fpga:kmi0", KMI0, NULL);
+AMBA_DEVICE(kmi1, "fpga:kmi1", KMI1, NULL);
+AMBA_DEVICE(uart3, "fpga:uart3", PBA8_UART3, NULL);
/* DevChip Primecells */
-AMBA_DEVICE(smc, "dev:00", PBA8_SMC, NULL);
-AMBA_DEVICE(sctl, "dev:e0", SCTL, NULL);
-AMBA_DEVICE(wdog, "dev:e1", PBA8_WATCHDOG, NULL);
-AMBA_DEVICE(gpio0, "dev:e4", PBA8_GPIO0, &gpio0_plat_data);
-AMBA_DEVICE(gpio1, "dev:e5", GPIO1, &gpio1_plat_data);
-AMBA_DEVICE(gpio2, "dev:e6", GPIO2, &gpio2_plat_data);
-AMBA_DEVICE(rtc, "dev:e8", PBA8_RTC, NULL);
-AMBA_DEVICE(sci0, "dev:f0", SCI, NULL);
-AMBA_DEVICE(uart0, "dev:f1", PBA8_UART0, NULL);
-AMBA_DEVICE(uart1, "dev:f2", PBA8_UART1, NULL);
-AMBA_DEVICE(uart2, "dev:f3", PBA8_UART2, NULL);
-AMBA_DEVICE(ssp0, "dev:f4", PBA8_SSP, NULL);
+AMBA_DEVICE(smc, "dev:smc", PBA8_SMC, NULL);
+AMBA_DEVICE(sctl, "dev:sctl", SCTL, NULL);
+AMBA_DEVICE(wdog, "dev:wdog", PBA8_WATCHDOG, NULL);
+AMBA_DEVICE(gpio0, "dev:gpio0", PBA8_GPIO0, &gpio0_plat_data);
+AMBA_DEVICE(gpio1, "dev:gpio1", GPIO1, &gpio1_plat_data);
+AMBA_DEVICE(gpio2, "dev:gpio2", GPIO2, &gpio2_plat_data);
+AMBA_DEVICE(rtc, "dev:rtc", PBA8_RTC, NULL);
+AMBA_DEVICE(sci0, "dev:sci0", SCI, NULL);
+AMBA_DEVICE(uart0, "dev:uart0", PBA8_UART0, NULL);
+AMBA_DEVICE(uart1, "dev:uart1", PBA8_UART1, NULL);
+AMBA_DEVICE(uart2, "dev:uart2", PBA8_UART2, NULL);
+AMBA_DEVICE(ssp0, "dev:ssp0", PBA8_SSP, NULL);
/* Primecells on the NEC ISSP chip */
-AMBA_DEVICE(clcd, "issp:20", PBA8_CLCD, &clcd_plat_data);
-AMBA_DEVICE(dmac, "issp:30", DMAC, NULL);
+AMBA_DEVICE(clcd, "issp:clcd", PBA8_CLCD, &clcd_plat_data);
+AMBA_DEVICE(dmac, "issp:dmac", DMAC, NULL);
static struct amba_device *amba_devs[] __initdata = {
&dmac_device,
#include <linux/sysdev.h>
#include <linux/amba/bus.h>
#include <linux/amba/pl061.h>
+#include <linux/amba/mmci.h>
#include <linux/io.h>
#include <asm/irq.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <asm/mach/mmc.h>
#include <asm/mach/time.h>
#include <mach/hardware.h>
#define PBX_SSP_DMA { 9, 8 }
/* FPGA Primecells */
-AMBA_DEVICE(aaci, "fpga:04", AACI, NULL);
-AMBA_DEVICE(mmc0, "fpga:05", MMCI0, &realview_mmc0_plat_data);
-AMBA_DEVICE(kmi0, "fpga:06", KMI0, NULL);
-AMBA_DEVICE(kmi1, "fpga:07", KMI1, NULL);
-AMBA_DEVICE(uart3, "fpga:09", PBX_UART3, NULL);
+AMBA_DEVICE(aaci, "fpga:aaci", AACI, NULL);
+AMBA_DEVICE(mmc0, "fpga:mmc0", MMCI0, &realview_mmc0_plat_data);
+AMBA_DEVICE(kmi0, "fpga:kmi0", KMI0, NULL);
+AMBA_DEVICE(kmi1, "fpga:kmi1", KMI1, NULL);
+AMBA_DEVICE(uart3, "fpga:uart3", PBX_UART3, NULL);
/* DevChip Primecells */
-AMBA_DEVICE(smc, "dev:00", PBX_SMC, NULL);
-AMBA_DEVICE(sctl, "dev:e0", SCTL, NULL);
-AMBA_DEVICE(wdog, "dev:e1", PBX_WATCHDOG, NULL);
-AMBA_DEVICE(gpio0, "dev:e4", PBX_GPIO0, &gpio0_plat_data);
-AMBA_DEVICE(gpio1, "dev:e5", GPIO1, &gpio1_plat_data);
-AMBA_DEVICE(gpio2, "dev:e6", GPIO2, &gpio2_plat_data);
-AMBA_DEVICE(rtc, "dev:e8", PBX_RTC, NULL);
-AMBA_DEVICE(sci0, "dev:f0", SCI, NULL);
-AMBA_DEVICE(uart0, "dev:f1", PBX_UART0, NULL);
-AMBA_DEVICE(uart1, "dev:f2", PBX_UART1, NULL);
-AMBA_DEVICE(uart2, "dev:f3", PBX_UART2, NULL);
-AMBA_DEVICE(ssp0, "dev:f4", PBX_SSP, NULL);
+AMBA_DEVICE(smc, "dev:smc", PBX_SMC, NULL);
+AMBA_DEVICE(sctl, "dev:sctl", SCTL, NULL);
+AMBA_DEVICE(wdog, "dev:wdog", PBX_WATCHDOG, NULL);
+AMBA_DEVICE(gpio0, "dev:gpio0", PBX_GPIO0, &gpio0_plat_data);
+AMBA_DEVICE(gpio1, "dev:gpio1", GPIO1, &gpio1_plat_data);
+AMBA_DEVICE(gpio2, "dev:gpio2", GPIO2, &gpio2_plat_data);
+AMBA_DEVICE(rtc, "dev:rtc", PBX_RTC, NULL);
+AMBA_DEVICE(sci0, "dev:sci0", SCI, NULL);
+AMBA_DEVICE(uart0, "dev:uart0", PBX_UART0, NULL);
+AMBA_DEVICE(uart1, "dev:uart1", PBX_UART1, NULL);
+AMBA_DEVICE(uart2, "dev:uart2", PBX_UART2, NULL);
+AMBA_DEVICE(ssp0, "dev:ssp0", PBX_SSP, NULL);
/* Primecells on the NEC ISSP chip */
-AMBA_DEVICE(clcd, "issp:20", PBX_CLCD, &clcd_plat_data);
-AMBA_DEVICE(dmac, "issp:30", DMAC, NULL);
+AMBA_DEVICE(clcd, "issp:clcd", PBX_CLCD, &clcd_plat_data);
+AMBA_DEVICE(dmac, "issp:dmac", DMAC, NULL);
static struct amba_device *amba_devs[] __initdata = {
&dmac_device,
select CPU_S3C2410
select PM_H1940 if PM
select S3C_DEV_USB_HOST
+ select S3C_DEV_NAND
help
Say Y here if you are using the HP IPAQ H1940
bool "Acer N30 family"
select CPU_S3C2410
select S3C_DEV_USB_HOST
+ select S3C_DEV_NAND
help
Say Y here if you want suppt for the Acer N30, Acer N35,
Navman PiN570, Yakumo AlphaX or Airis NC05 PDAs.
select S3C24XX_DCLK
select ISA
select S3C_DEV_USB_HOST
+ select S3C_DEV_NAND
help
Say Y here if you are using the Simtec Electronics EB2410ITX
development board (also known as BAST)
bool "NexVision OTOM Board"
select CPU_S3C2410
select S3C_DEV_USB_HOST
+ select S3C_DEV_NAND
help
Say Y here if you are using the Nex Vision OTOM board
bool "QT2410"
select CPU_S3C2410
select S3C_DEV_USB_HOST
+ select S3C_DEV_NAND
help
Say Y here if you are using the Armzone QT2410
bool "Logitech Jive"
select CPU_S3C2412
select S3C_DEV_USB_HOST
+ select S3C_DEV_NAND
help
Say Y here if you are using the Logitech Jive.
select MACH_S3C2413
select MACH_SMDK
select S3C_DEV_USB_HOST
+ select S3C_DEV_NAND
help
Say Y here if you are using an SMDK2413
bool "VMSTMS"
select CPU_S3C2412
select S3C_DEV_USB_HOST
+ select S3C_DEV_NAND
help
Say Y here if you are using an VSTMS board
select S3C2440_XTAL_12000000
select S3C2410_IOTIMING if S3C2440_CPUFREQ
select S3C_DEV_USB_HOST
+ select S3C_DEV_NAND
help
Say Y here if you are using the Simtec IM2440D20 module, also
known as the Osiris.
select CPU_S3C2440
select S3C2440_XTAL_16934400
select PM_H1940 if PM
+ select S3C_DEV_NAND
help
Say Y here if you are using the HP iPAQ rx3715.
select S3C2440_XTAL_16934400
select MACH_SMDK
select S3C_DEV_USB_HOST
+ select S3C_DEV_NAND
help
Say Y here if you are using the SMDK2440.
select CPU_S3C2440
select S3C2440_XTAL_12000000
select S3C_DEV_USB_HOST
+ select S3C_DEV_NAND
help
Say Y here if you are using the Nex Vision NEXCODER 2440 Light Board
bool "Avantech AT2440EVB development board"
select CPU_S3C2440
select S3C_DEV_USB_HOST
+ select S3C_DEV_NAND
help
Say Y here if you are using the AT2440EVB development board
select EEPROM_AT24
select LEDS_TRIGGER_BACKLIGHT
select SND_S3C24XX_SOC_S3C24XX_UDA134X
+ select S3C_DEV_NAND
help
Say Y here to select support for the MINI2440. Is a 10cm x 10cm board
available via various sources. It can come with a 3.5" or 7" touch LCD.
bool "SMDK6400"
select CPU_S3C6400
select S3C_DEV_HSMMC
+ select S3C_DEV_NAND
select S3C6400_SETUP_SDHCI
help
Machine support for the Samsung SMDK6400
bool "Airgoo HMT"
select CPU_S3C6410
select S3C_DEV_FB
+ select S3C_DEV_NAND
select S3C_DEV_USB_HOST
select S3C64XX_SETUP_FB_24BPP
select HAVE_PWM
static sa1100_dma_t dma_chan[SA1100_DMA_CHANNELS];
-static spinlock_t dma_list_lock;
+static DEFINE_SPINLOCK(dma_list_lock);
static irqreturn_t dma_irq_handler(int irq, void *dev_id)
Memory Interface) from both from access and application
side.
+config MACH_U300_SPIDUMMY
+ bool "SSP/SPI dummy chip"
+ select SPI
+ select SPI_MASTER
+ select SPI_PL022
+ help
+ This creates a small kernel module that creates a dummy
+ SPI device to be used for loopback tests. Regularly used
+ to test reference designs. If you're not testing SPI,
+ you don't need it. Selecting this will activate the
+ SPI framework and ARM PL022 support.
+
comment "All the settings below must match the bootloader's settings"
config MACH_U300_ACCESS_MEM_SIZE
obj-$(CONFIG_ARCH_U300) += u300.o
obj-$(CONFIG_MMC) += mmc.o
+obj-$(CONFIG_SPI_PL022) += spi.o
+obj-$(CONFIG_MACH_U300_SPIDUMMY) += dummyspichip.o
+obj-$(CONFIG_I2C_STU300) += i2c.o
#include "clock.h"
#include "mmc.h"
+#include "spi.h"
+#include "i2c.h"
/*
* Static I/O mappings that are needed for booting the U300 platforms. The
};
static struct platform_device i2c0_device = {
- .name = "stddci2c",
+ .name = "stu300",
.id = 0,
.num_resources = ARRAY_SIZE(i2c0_resources),
.resource = i2c0_resources,
};
static struct platform_device i2c1_device = {
- .name = "stddci2c",
+ .name = "stu300",
.id = 1,
.num_resources = ARRAY_SIZE(i2c1_resources),
.resource = i2c1_resources,
/* Wait for the PLL208 to lock if not locked in yet */
while (!(readw(U300_SYSCON_VBASE + U300_SYSCON_CSR) &
U300_SYSCON_CSR_PLL208_LOCK_IND));
+ /* Initialize SPI device with some board specifics */
+ u300_spi_init(&pl022_device);
/* Register the AMBA devices in the AMBA bus abstraction layer */
u300_clock_primecells();
u300_assign_physmem();
+ /* Register subdevices on the I2C buses */
+ u300_i2c_register_board_devices();
+
+ /* Register subdevices on the SPI bus */
+ u300_spi_register_board_devices();
+
/* Register the platform devices */
platform_add_devices(platform_devs, ARRAY_SIZE(platform_devs));
--- /dev/null
+/*
+ * arch/arm/mach-u300/dummyspichip.c
+ *
+ * Copyright (C) 2007-2009 ST-Ericsson AB
+ * License terms: GNU General Public License (GPL) version 2
+ * This is a dummy loopback SPI "chip" used for testing SPI.
+ * Author: Linus Walleij <linus.walleij@stericsson.com>
+ */
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/sysfs.h>
+#include <linux/mutex.h>
+#include <linux/spi/spi.h>
+#include <linux/dma-mapping.h>
+/*
+ * WARNING! Do not include this pl022-specific controller header
+ * for any generic driver. It is only done in this dummy chip
+ * because we alter the chip configuration in order to test some
+ * different settings on the loopback device. Normal chip configs
+ * shall be STATIC and not altered by the driver!
+ */
+#include <linux/amba/pl022.h>
+
+struct dummy {
+ struct device *dev;
+ struct mutex lock;
+};
+
+#define DMA_TEST_SIZE 2048
+
+/* When we cat /sys/bus/spi/devices/spi0.0/looptest this will be triggered */
+static ssize_t dummy_looptest(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct spi_device *spi = to_spi_device(dev);
+ struct dummy *p_dummy = dev_get_drvdata(&spi->dev);
+
+ /*
+ * WARNING! Do not dereference the chip-specific data in any normal
+ * driver for a chip. It is usually STATIC and shall not be read
+ * or written to. Your chip driver should NOT depend on fields in this
+ * struct, this is just used here to alter the behaviour of the chip
+ * in order to perform tests.
+ */
+ struct pl022_config_chip *chip_info = spi->controller_data;
+ int status;
+ u8 txbuf[14] = {0xDE, 0xAD, 0xBE, 0xEF, 0x2B, 0xAD,
+ 0xCA, 0xFE, 0xBA, 0xBE, 0xB1, 0x05,
+ 0xF0, 0x0D};
+ u8 rxbuf[14];
+ u8 *bigtxbuf_virtual;
+ u8 *bigrxbuf_virtual;
+
+ if (mutex_lock_interruptible(&p_dummy->lock))
+ return -ERESTARTSYS;
+
+ bigtxbuf_virtual = kmalloc(DMA_TEST_SIZE, GFP_KERNEL);
+ if (bigtxbuf_virtual == NULL) {
+ status = -ENOMEM;
+ goto out;
+ }
+ bigrxbuf_virtual = kmalloc(DMA_TEST_SIZE, GFP_KERNEL);
+
+ /* Fill TXBUF with some happy pattern */
+ memset(bigtxbuf_virtual, 0xAA, DMA_TEST_SIZE);
+
+ /*
+ * Force chip to 8 bit mode
+ * WARNING: NEVER DO THIS IN REAL DRIVER CODE, THIS SHOULD BE STATIC!
+ */
+ chip_info->data_size = SSP_DATA_BITS_8;
+ /* You should NOT DO THIS EITHER */
+ spi->master->setup(spi);
+
+ /* Now run the tests for 8bit mode */
+ pr_info("Simple test 1: write 0xAA byte, read back garbage byte "
+ "in 8bit mode\n");
+ status = spi_w8r8(spi, 0xAA);
+ if (status < 0)
+ pr_warning("Siple test 1: FAILURE: spi_write_then_read "
+ "failed with status %d\n", status);
+ else
+ pr_info("Simple test 1: SUCCESS!\n");
+
+ pr_info("Simple test 2: write 8 bytes, read back 8 bytes garbage "
+ "in 8bit mode (full FIFO)\n");
+ status = spi_write_then_read(spi, &txbuf[0], 8, &rxbuf[0], 8);
+ if (status < 0)
+ pr_warning("Simple test 2: FAILURE: spi_write_then_read() "
+ "failed with status %d\n", status);
+ else
+ pr_info("Simple test 2: SUCCESS!\n");
+
+ pr_info("Simple test 3: write 14 bytes, read back 14 bytes garbage "
+ "in 8bit mode (see if we overflow FIFO)\n");
+ status = spi_write_then_read(spi, &txbuf[0], 14, &rxbuf[0], 14);
+ if (status < 0)
+ pr_warning("Simple test 3: FAILURE: failed with status %d "
+ "(probably FIFO overrun)\n", status);
+ else
+ pr_info("Simple test 3: SUCCESS!\n");
+
+ pr_info("Simple test 4: write 8 bytes with spi_write(), read 8 "
+ "bytes garbage with spi_read() in 8bit mode\n");
+ status = spi_write(spi, &txbuf[0], 8);
+ if (status < 0)
+ pr_warning("Simple test 4 step 1: FAILURE: spi_write() "
+ "failed with status %d\n", status);
+ else
+ pr_info("Simple test 4 step 1: SUCCESS!\n");
+ status = spi_read(spi, &rxbuf[0], 8);
+ if (status < 0)
+ pr_warning("Simple test 4 step 2: FAILURE: spi_read() "
+ "failed with status %d\n", status);
+ else
+ pr_info("Simple test 4 step 2: SUCCESS!\n");
+
+ pr_info("Simple test 5: write 14 bytes with spi_write(), read "
+ "14 bytes garbage with spi_read() in 8bit mode\n");
+ status = spi_write(spi, &txbuf[0], 14);
+ if (status < 0)
+ pr_warning("Simple test 5 step 1: FAILURE: spi_write() "
+ "failed with status %d (probably FIFO overrun)\n",
+ status);
+ else
+ pr_info("Simple test 5 step 1: SUCCESS!\n");
+ status = spi_read(spi, &rxbuf[0], 14);
+ if (status < 0)
+ pr_warning("Simple test 5 step 2: FAILURE: spi_read() "
+ "failed with status %d (probably FIFO overrun)\n",
+ status);
+ else
+ pr_info("Simple test 5: SUCCESS!\n");
+
+ pr_info("Simple test 6: write %d bytes with spi_write(), "
+ "read %d bytes garbage with spi_read() in 8bit mode\n",
+ DMA_TEST_SIZE, DMA_TEST_SIZE);
+ status = spi_write(spi, &bigtxbuf_virtual[0], DMA_TEST_SIZE);
+ if (status < 0)
+ pr_warning("Simple test 6 step 1: FAILURE: spi_write() "
+ "failed with status %d (probably FIFO overrun)\n",
+ status);
+ else
+ pr_info("Simple test 6 step 1: SUCCESS!\n");
+ status = spi_read(spi, &bigrxbuf_virtual[0], DMA_TEST_SIZE);
+ if (status < 0)
+ pr_warning("Simple test 6 step 2: FAILURE: spi_read() "
+ "failed with status %d (probably FIFO overrun)\n",
+ status);
+ else
+ pr_info("Simple test 6: SUCCESS!\n");
+
+
+ /*
+ * Force chip to 16 bit mode
+ * WARNING: NEVER DO THIS IN REAL DRIVER CODE, THIS SHOULD BE STATIC!
+ */
+ chip_info->data_size = SSP_DATA_BITS_16;
+ /* You should NOT DO THIS EITHER */
+ spi->master->setup(spi);
+
+ pr_info("Simple test 7: write 0xAA byte, read back garbage byte "
+ "in 16bit bus mode\n");
+ status = spi_w8r8(spi, 0xAA);
+ if (status == -EIO)
+ pr_info("Simple test 7: SUCCESS! (expected failure with "
+ "status EIO)\n");
+ else if (status < 0)
+ pr_warning("Siple test 7: FAILURE: spi_write_then_read "
+ "failed with status %d\n", status);
+ else
+ pr_warning("Siple test 7: FAILURE: spi_write_then_read "
+ "succeeded but it was expected to fail!\n");
+
+ pr_info("Simple test 8: write 8 bytes, read back 8 bytes garbage "
+ "in 16bit mode (full FIFO)\n");
+ status = spi_write_then_read(spi, &txbuf[0], 8, &rxbuf[0], 8);
+ if (status < 0)
+ pr_warning("Simple test 8: FAILURE: spi_write_then_read() "
+ "failed with status %d\n", status);
+ else
+ pr_info("Simple test 8: SUCCESS!\n");
+
+ pr_info("Simple test 9: write 14 bytes, read back 14 bytes garbage "
+ "in 16bit mode (see if we overflow FIFO)\n");
+ status = spi_write_then_read(spi, &txbuf[0], 14, &rxbuf[0], 14);
+ if (status < 0)
+ pr_warning("Simple test 9: FAILURE: failed with status %d "
+ "(probably FIFO overrun)\n", status);
+ else
+ pr_info("Simple test 9: SUCCESS!\n");
+
+ pr_info("Simple test 10: write %d bytes with spi_write(), "
+ "read %d bytes garbage with spi_read() in 16bit mode\n",
+ DMA_TEST_SIZE, DMA_TEST_SIZE);
+ status = spi_write(spi, &bigtxbuf_virtual[0], DMA_TEST_SIZE);
+ if (status < 0)
+ pr_warning("Simple test 10 step 1: FAILURE: spi_write() "
+ "failed with status %d (probably FIFO overrun)\n",
+ status);
+ else
+ pr_info("Simple test 10 step 1: SUCCESS!\n");
+
+ status = spi_read(spi, &bigrxbuf_virtual[0], DMA_TEST_SIZE);
+ if (status < 0)
+ pr_warning("Simple test 10 step 2: FAILURE: spi_read() "
+ "failed with status %d (probably FIFO overrun)\n",
+ status);
+ else
+ pr_info("Simple test 10: SUCCESS!\n");
+
+ status = sprintf(buf, "loop test complete\n");
+ kfree(bigrxbuf_virtual);
+ kfree(bigtxbuf_virtual);
+ out:
+ mutex_unlock(&p_dummy->lock);
+ return status;
+}
+
+static DEVICE_ATTR(looptest, S_IRUGO, dummy_looptest, NULL);
+
+static int __devinit pl022_dummy_probe(struct spi_device *spi)
+{
+ struct dummy *p_dummy;
+ int status;
+
+ dev_info(&spi->dev, "probing dummy SPI device\n");
+
+ p_dummy = kzalloc(sizeof *p_dummy, GFP_KERNEL);
+ if (!p_dummy)
+ return -ENOMEM;
+
+ dev_set_drvdata(&spi->dev, p_dummy);
+ mutex_init(&p_dummy->lock);
+
+ /* sysfs hook */
+ status = device_create_file(&spi->dev, &dev_attr_looptest);
+ if (status) {
+ dev_dbg(&spi->dev, "device_create_file looptest failure.\n");
+ goto out_dev_create_looptest_failed;
+ }
+
+ return 0;
+
+out_dev_create_looptest_failed:
+ dev_set_drvdata(&spi->dev, NULL);
+ kfree(p_dummy);
+ return status;
+}
+
+static int __devexit pl022_dummy_remove(struct spi_device *spi)
+{
+ struct dummy *p_dummy = dev_get_drvdata(&spi->dev);
+
+ dev_info(&spi->dev, "removing dummy SPI device\n");
+ device_remove_file(&spi->dev, &dev_attr_looptest);
+ dev_set_drvdata(&spi->dev, NULL);
+ kfree(p_dummy);
+
+ return 0;
+}
+
+static struct spi_driver pl022_dummy_driver = {
+ .driver = {
+ .name = "spi-dummy",
+ .owner = THIS_MODULE,
+ },
+ .probe = pl022_dummy_probe,
+ .remove = __devexit_p(pl022_dummy_remove),
+};
+
+static int __init pl022_init_dummy(void)
+{
+ return spi_register_driver(&pl022_dummy_driver);
+}
+
+static void __exit pl022_exit_dummy(void)
+{
+ spi_unregister_driver(&pl022_dummy_driver);
+}
+
+module_init(pl022_init_dummy);
+module_exit(pl022_exit_dummy);
+
+MODULE_AUTHOR("Linus Walleij <linus.walleij@stericsson.com>");
+MODULE_DESCRIPTION("PL022 SSP/SPI DUMMY Linux driver");
+MODULE_LICENSE("GPL");
#include <linux/platform_device.h>
#include <linux/gpio.h>
-/* Need access to SYSCON registers for PADmuxing */
-#include <mach/syscon.h>
-
-#include "padmux.h"
-
/* Reference to GPIO block clock */
static struct clk *clk;
writel(U300_GPIO_CR_BLOCK_CLKRQ_ENABLE, virtbase + U300_GPIO_CR);
#endif
- /* Set up some padmuxing here */
-#ifdef CONFIG_MMC
- pmx_set_mission_mode_mmc();
-#endif
-#ifdef CONFIG_SPI_PL022
- pmx_set_mission_mode_spi();
-#endif
-
gpio_set_initial_values();
for (num_irqs = 0 ; num_irqs < U300_GPIO_NUM_PORTS; num_irqs++) {
--- /dev/null
+/*
+ * arch/arm/mach-u300/i2c.c
+ *
+ * Copyright (C) 2009 ST-Ericsson AB
+ * License terms: GNU General Public License (GPL) version 2
+ *
+ * Register board i2c devices
+ * Author: Linus Walleij <linus.walleij@stericsson.com>
+ */
+#include <linux/kernel.h>
+#include <linux/i2c.h>
+#include <mach/irqs.h>
+
+static struct i2c_board_info __initdata bus0_i2c_board_info[] = {
+ {
+ .type = "ab3100",
+ .addr = 0x48,
+ .irq = IRQ_U300_IRQ0_EXT,
+ },
+};
+
+static struct i2c_board_info __initdata bus1_i2c_board_info[] = {
+#ifdef CONFIG_MACH_U300_BS335
+ {
+ .type = "fwcam",
+ .addr = 0x10,
+ },
+ {
+ .type = "fwcam",
+ .addr = 0x5d,
+ },
+#else
+ { },
+#endif
+};
+
+void __init u300_i2c_register_board_devices(void)
+{
+ i2c_register_board_info(0, bus0_i2c_board_info,
+ ARRAY_SIZE(bus0_i2c_board_info));
+ i2c_register_board_info(1, bus1_i2c_board_info,
+ ARRAY_SIZE(bus1_i2c_board_info));
+}
--- /dev/null
+/*
+ * arch/arm/mach-u300/i2c.h
+ *
+ * Copyright (C) 2009 ST-Ericsson AB
+ * License terms: GNU General Public License (GPL) version 2
+ *
+ * Register board i2c devices
+ * Author: Linus Walleij <linus.walleij@stericsson.com>
+ */
+
+#ifndef MACH_U300_I2C_H
+#define MACH_U300_I2C_H
+
+#ifdef CONFIG_I2C_STU300
+void __init u300_i2c_register_board_devices(void);
+#else
+/* Compile out this stuff if no I2C adapter is available */
+static inline void __init u300_i2c_register_board_devices(void)
+{
+}
+#endif
+
+#endif
(CONFIG_MACH_U300_ACCESS_MEM_SIZE & 1))*1024*1024 + 0x100)
#endif
+/*
+ * TCM memory whereabouts
+ */
+#define ITCM_OFFSET 0xffff2000
+#define ITCM_END 0xffff3fff
+#define DTCM_OFFSET 0xffff4000
+#define DTCM_END 0xffff5fff
+
/*
* We enable a real big DMA buffer if need be.
*/
#define U300_SYSCON_PMC1LR_CDI_MASK (0xC000)
#define U300_SYSCON_PMC1LR_CDI_CDI (0x0000)
#define U300_SYSCON_PMC1LR_CDI_EMIF (0x4000)
+#ifdef CONFIG_MACH_U300_BS335
+#define U300_SYSCON_PMC1LR_CDI_CDI2 (0x8000)
+#define U300_SYSCON_PMC1LR_CDI_WCDMA_APP_GPIO (0xC000)
+#elif CONFIG_MACH_U300_BS365
#define U300_SYSCON_PMC1LR_CDI_GPIO (0x8000)
#define U300_SYSCON_PMC1LR_CDI_WCDMA (0xC000)
+#endif
#define U300_SYSCON_PMC1LR_PDI_MASK (0x3000)
#define U300_SYSCON_PMC1LR_PDI_PDI (0x0000)
#define U300_SYSCON_PMC1LR_PDI_EGG (0x1000)
#define U300_SYSCON_MMCR_MASK (0x0003)
#define U300_SYSCON_MMCR_MMC_FB_CLK_SEL_ENABLE (0x0002)
#define U300_SYSCON_MMCR_MSPRO_FREQSEL_ENABLE (0x0001)
-
+/* Pull up/down control (R/W) */
+#define U300_SYSCON_PUCR (0x104)
+#define U300_SYSCON_PUCR_EMIF_1_WAIT_N_PU_ENABLE (0x0200)
+#define U300_SYSCON_PUCR_EMIF_1_NFIF_READY_PU_ENABLE (0x0100)
+#define U300_SYSCON_PUCR_EMIF_1_16BIT_PU_ENABLE (0x0080)
+#define U300_SYSCON_PUCR_EMIF_1_8BIT_PU_ENABLE (0x0040)
+#define U300_SYSCON_PUCR_KEY_IN_PU_EN_MASK (0x003F)
+/* Padmux 2 control */
+#define U300_SYSCON_PMC2R (0x100)
+#define U300_SYSCON_PMC2R_APP_MISC_0_MASK (0x00C0)
+#define U300_SYSCON_PMC2R_APP_MISC_0_APP_GPIO (0x0000)
+#define U300_SYSCON_PMC2R_APP_MISC_0_EMIF_SDRAM (0x0040)
+#define U300_SYSCON_PMC2R_APP_MISC_0_MMC (0x0080)
+#define U300_SYSCON_PMC2R_APP_MISC_0_CDI2 (0x00C0)
+#define U300_SYSCON_PMC2R_APP_MISC_1_MASK (0x0300)
+#define U300_SYSCON_PMC2R_APP_MISC_1_APP_GPIO (0x0000)
+#define U300_SYSCON_PMC2R_APP_MISC_1_EMIF_SDRAM (0x0100)
+#define U300_SYSCON_PMC2R_APP_MISC_1_MMC (0x0200)
+#define U300_SYSCON_PMC2R_APP_MISC_1_CDI2 (0x0300)
+#define U300_SYSCON_PMC2R_APP_MISC_2_MASK (0x0C00)
+#define U300_SYSCON_PMC2R_APP_MISC_2_APP_GPIO (0x0000)
+#define U300_SYSCON_PMC2R_APP_MISC_2_EMIF_SDRAM (0x0400)
+#define U300_SYSCON_PMC2R_APP_MISC_2_MMC (0x0800)
+#define U300_SYSCON_PMC2R_APP_MISC_2_CDI2 (0x0C00)
+#define U300_SYSCON_PMC2R_APP_MISC_3_MASK (0x3000)
+#define U300_SYSCON_PMC2R_APP_MISC_3_APP_GPIO (0x0000)
+#define U300_SYSCON_PMC2R_APP_MISC_3_EMIF_SDRAM (0x1000)
+#define U300_SYSCON_PMC2R_APP_MISC_3_MMC (0x2000)
+#define U300_SYSCON_PMC2R_APP_MISC_3_CDI2 (0x3000)
+#define U300_SYSCON_PMC2R_APP_MISC_4_MASK (0xC000)
+#define U300_SYSCON_PMC2R_APP_MISC_4_APP_GPIO (0x0000)
+#define U300_SYSCON_PMC2R_APP_MISC_4_EMIF_SDRAM (0x4000)
+#define U300_SYSCON_PMC2R_APP_MISC_4_MMC (0x8000)
+#define U300_SYSCON_PMC2R_APP_MISC_4_ACC_GPIO (0xC000)
/* TODO: More SYSCON registers missing */
#define U300_SYSCON_PMC3R (0x10c)
#define U300_SYSCON_PMC3R_APP_MISC_11_MASK (0xc000)
#define U300_SYSCON_PMC3R_APP_MISC_11_SPI (0x4000)
#define U300_SYSCON_PMC3R_APP_MISC_10_MASK (0x3000)
#define U300_SYSCON_PMC3R_APP_MISC_10_SPI (0x1000)
-/* TODO: Missing other configs, I just added the SPI stuff */
-
+/* TODO: Missing other configs */
+#define U300_SYSCON_PMC4R (0x168)
+#define U300_SYSCON_PMC4R_APP_MISC_12_MASK (0x0003)
+#define U300_SYSCON_PMC4R_APP_MISC_12_APP_GPIO (0x0000)
+#define U300_SYSCON_PMC4R_APP_MISC_13_MASK (0x000C)
+#define U300_SYSCON_PMC4R_APP_MISC_13_CDI (0x0000)
+#define U300_SYSCON_PMC4R_APP_MISC_13_SMIA (0x0004)
+#define U300_SYSCON_PMC4R_APP_MISC_13_SMIA2 (0x0008)
+#define U300_SYSCON_PMC4R_APP_MISC_13_APP_GPIO (0x000C)
+#define U300_SYSCON_PMC4R_APP_MISC_14_MASK (0x0030)
+#define U300_SYSCON_PMC4R_APP_MISC_14_CDI (0x0000)
+#define U300_SYSCON_PMC4R_APP_MISC_14_SMIA (0x0010)
+#define U300_SYSCON_PMC4R_APP_MISC_14_CDI2 (0x0020)
+#define U300_SYSCON_PMC4R_APP_MISC_14_APP_GPIO (0x0030)
+#define U300_SYSCON_PMC4R_APP_MISC_16_MASK (0x0300)
+#define U300_SYSCON_PMC4R_APP_MISC_16_APP_GPIO_13 (0x0000)
+#define U300_SYSCON_PMC4R_APP_MISC_16_APP_UART1_CTS (0x0100)
+#define U300_SYSCON_PMC4R_APP_MISC_16_EMIF_1_STATIC_CS5_N (0x0200)
/* SYS_0_CLK_CONTROL first clock control 16bit (R/W) */
#define U300_SYSCON_S0CCR (0x120)
#define U300_SYSCON_S0CCR_FIELD_MASK (0x43FF)
#define U300_SYSCON_S0CCR_CLOCK_REQ (0x4000)
+#define U300_SYSCON_S0CCR_CLOCK_REQ_MONITOR (0x2000)
#define U300_SYSCON_S0CCR_CLOCK_INV (0x0200)
#define U300_SYSCON_S0CCR_CLOCK_FREQ_MASK (0x01E0)
#define U300_SYSCON_S0CCR_CLOCK_SELECT_MASK (0x001E)
#define U300_SYSCON_S1CCR (0x124)
#define U300_SYSCON_S1CCR_FIELD_MASK (0x43FF)
#define U300_SYSCON_S1CCR_CLOCK_REQ (0x4000)
+#define U300_SYSCON_S1CCR_CLOCK_REQ_MONITOR (0x2000)
#define U300_SYSCON_S1CCR_CLOCK_INV (0x0200)
#define U300_SYSCON_S1CCR_CLOCK_FREQ_MASK (0x01E0)
#define U300_SYSCON_S1CCR_CLOCK_SELECT_MASK (0x001E)
#define U300_SYSCON_S2CCR_FIELD_MASK (0xC3FF)
#define U300_SYSCON_S2CCR_CLK_STEAL (0x8000)
#define U300_SYSCON_S2CCR_CLOCK_REQ (0x4000)
+#define U300_SYSCON_S2CCR_CLOCK_REQ_MONITOR (0x2000)
#define U300_SYSCON_S2CCR_CLOCK_INV (0x0200)
#define U300_SYSCON_S2CCR_CLOCK_FREQ_MASK (0x01E0)
#define U300_SYSCON_S2CCR_CLOCK_SELECT_MASK (0x001E)
#define U300_SYSCON_MCR_PMGEN_CR_0_EMIF_0_SDRAM (0x000C)
#define U300_SYSCON_MCR_PM1G_MODE_ENABLE (0x0002)
#define U300_SYSCON_MCR_PMTG5_MODE_ENABLE (0x0001)
+/* SC_PLL_IRQ_CONTROL 16bit (R/W) */
+#define U300_SYSCON_PICR (0x0130)
+#define U300_SYSCON_PICR_MASK (0x00FF)
+#define U300_SYSCON_PICR_FORCE_PLL208_LOCK_LOW_ENABLE (0x0080)
+#define U300_SYSCON_PICR_FORCE_PLL208_LOCK_HIGH_ENABLE (0x0040)
+#define U300_SYSCON_PICR_FORCE_PLL13_LOCK_LOW_ENABLE (0x0020)
+#define U300_SYSCON_PICR_FORCE_PLL13_LOCK_HIGH_ENABLE (0x0010)
+#define U300_SYSCON_PICR_IRQMASK_PLL13_UNLOCK_ENABLE (0x0008)
+#define U300_SYSCON_PICR_IRQMASK_PLL13_LOCK_ENABLE (0x0004)
+#define U300_SYSCON_PICR_IRQMASK_PLL208_UNLOCK_ENABLE (0x0002)
+#define U300_SYSCON_PICR_IRQMASK_PLL208_LOCK_ENABLE (0x0001)
+/* SC_PLL_IRQ_STATUS 16 bit (R/-) */
+#define U300_SYSCON_PISR (0x0134)
+#define U300_SYSCON_PISR_MASK (0x000F)
+#define U300_SYSCON_PISR_PLL13_UNLOCK_IND (0x0008)
+#define U300_SYSCON_PISR_PLL13_LOCK_IND (0x0004)
+#define U300_SYSCON_PISR_PLL208_UNLOCK_IND (0x0002)
+#define U300_SYSCON_PISR_PLL208_LOCK_IND (0x0001)
+/* SC_PLL_IRQ_CLEAR 16 bit (-/W) */
+#define U300_SYSCON_PICLR (0x0138)
+#define U300_SYSCON_PICLR_MASK (0x000F)
+#define U300_SYSCON_PICLR_RWMASK (0x0000)
+#define U300_SYSCON_PICLR_PLL13_UNLOCK_SC (0x0008)
+#define U300_SYSCON_PICLR_PLL13_LOCK_SC (0x0004)
+#define U300_SYSCON_PICLR_PLL208_UNLOCK_SC (0x0002)
+#define U300_SYSCON_PICLR_PLL208_LOCK_SC (0x0001)
+/* CAMIF_CONTROL 16 bit (-/W) */
+#define U300_SYSCON_CICR (0x013C)
+#define U300_SYSCON_CICR_MASK (0x0FFF)
+#define U300_SYSCON_CICR_APP_SUBLVDS_TESTMODE_MASK (0x0F00)
+#define U300_SYSCON_CICR_APP_SUBLVDS_TESTMODE_PORT1 (0x0C00)
+#define U300_SYSCON_CICR_APP_SUBLVDS_TESTMODE_PORT0 (0x0300)
+#define U300_SYSCON_CICR_APP_SUBLVDS_RESCON_MASK (0x00F0)
+#define U300_SYSCON_CICR_APP_SUBLVDS_RESCON_PORT1 (0x00C0)
+#define U300_SYSCON_CICR_APP_SUBLVDS_RESCON_PORT0 (0x0030)
+#define U300_SYSCON_CICR_APP_SUBLVDS_PWR_DWN_N_MASK (0x000F)
+#define U300_SYSCON_CICR_APP_SUBLVDS_PWR_DWN_N_PORT1 (0x000C)
+#define U300_SYSCON_CICR_APP_SUBLVDS_PWR_DWN_N_PORT0 (0x0003)
/* Clock activity observability register 0 */
#define U300_SYSCON_C0OAR (0x140)
#define U300_SYSCON_C0OAR_MASK (0xFFFF)
/**
* CPU medium frequency in MHz
*/
-#define SYSCON_CPU_CLOCK_MEDIUM 104
+#define SYSCON_CPU_CLOCK_MEDIUM 52
/**
* CPU low frequency in MHz
*/
/**
* EMIF medium frequency in MHz
*/
-#define SYSCON_EMIF_CLOCK_MEDIUM 104
+#define SYSCON_EMIF_CLOCK_MEDIUM 52
/**
* EMIF low frequency in MHz
*/
/**
* AHB medium frequency in MHz
*/
-#define SYSCON_AHB_CLOCK_MEDIUM 52
+#define SYSCON_AHB_CLOCK_MEDIUM 26
/**
* AHB low frequency in MHz
*/
SYSCON_BM_VIDEO_ENC
};
+/* Selectr a resistor or a set of resistors */
+enum syscon_pull_up_down {
+ SYSCON_PU_KEY_IN_EN,
+ SYSCON_PU_EMIF_1_8_BIT_EN,
+ SYSCON_PU_EMIF_1_16_BIT_EN,
+ SYSCON_PU_EMIF_1_NFIF_READY_EN,
+ SYSCON_PU_EMIF_1_NFIF_WAIT_N_EN,
+};
+
/*
* Note that this array must match the order of the array "clk_reg"
* in syscon.c
SYSCON_CLKCONTROL_SPI,
SYSCON_CLKCONTROL_I2S0_CORE,
SYSCON_CLKCONTROL_I2S1_CORE,
+ SYSCON_CLKCONTROL_UART1,
SYSCON_CLKCONTROL_AAIF,
SYSCON_CLKCONTROL_AHB,
SYSCON_CLKCONTROL_APEX,
enum syscon_sysclk_req {
SYSCON_SYSCLKREQ_DISABLED,
- SYSCON_SYSCLKREQ_ACTIVE_LOW
+ SYSCON_SYSCLKREQ_ACTIVE_LOW,
+ SYSCON_SYSCLKREQ_MONITOR
};
enum syscon_clk_mode {
#include <linux/regulator/consumer.h>
#include <linux/regulator/machine.h>
#include <linux/gpio.h>
+#include <linux/amba/mmci.h>
-#include <asm/mach/mmc.h>
#include "mmc.h"
+#include "padmux.h"
struct mmci_card_event {
struct input_dev *mmc_input;
int mmc_inserted;
struct work_struct workq;
- struct mmc_platform_data mmc0_plat_data;
+ struct mmci_platform_data mmc0_plat_data;
};
static unsigned int mmc_status(struct device *dev)
{
struct mmci_card_event *mmci_card;
struct device *mmcsd_device = &adev->dev;
+ struct pmx *pmx;
int ret = 0;
mmci_card = kzalloc(sizeof(struct mmci_card_event), GFP_KERNEL);
mmci_card->mmc0_plat_data.status = mmc_status;
mmci_card->mmc0_plat_data.gpio_wp = -1;
mmci_card->mmc0_plat_data.gpio_cd = -1;
+ mmci_card->mmc0_plat_data.capabilities = MMC_CAP_MMC_HIGHSPEED |
+ MMC_CAP_SD_HIGHSPEED | MMC_CAP_4_BIT_DATA;
mmcsd_device->platform_data = (void *) &mmci_card->mmc0_plat_data;
input_set_drvdata(mmci_card->mmc_input, mmci_card);
+ /*
+ * Setup padmuxing for MMC. Since this must always be
+ * compiled into the kernel, pmx is never released.
+ */
+ pmx = pmx_get(mmcsd_device, U300_APP_PMX_MMC_SETTING);
+
+ if (IS_ERR(pmx))
+ pr_warning("Could not get padmux handle\n");
+ else {
+ ret = pmx_activate(mmcsd_device, pmx);
+ if (IS_ERR_VALUE(ret))
+ pr_warning("Could not activate padmuxing\n");
+ }
+
ret = gpio_register_callback(U300_GPIO_PIN_MMC_CD, mmci_callback,
mmci_card);
* Copyright (C) 2009 ST-Ericsson AB
* License terms: GNU General Public License (GPL) version 2
* U300 PADMUX functions
- * Author: Linus Walleij <linus.walleij@stericsson.com>
- *
+ * Author: Martin Persson <martin.persson@stericsson.com>
*/
-#include <linux/io.h>
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/device.h>
#include <linux/err.h>
+#include <linux/errno.h>
+#include <linux/io.h>
+#include <linux/mutex.h>
+#include <linux/string.h>
+#include <linux/bug.h>
+#include <linux/debugfs.h>
+#include <linux/seq_file.h>
#include <mach/u300-regs.h>
#include <mach/syscon.h>
-
#include "padmux.h"
-/* Set the PAD MUX to route the MMC reader correctly to GPIO0. */
-void pmx_set_mission_mode_mmc(void)
-{
- u16 val;
-
- val = readw(U300_SYSCON_VBASE + U300_SYSCON_PMC1LR);
- val &= ~U300_SYSCON_PMC1LR_MMCSD_MASK;
- writew(val, U300_SYSCON_VBASE + U300_SYSCON_PMC1LR);
- val = readw(U300_SYSCON_VBASE + U300_SYSCON_PMC1HR);
- val &= ~U300_SYSCON_PMC1HR_APP_GPIO_1_MASK;
- val |= U300_SYSCON_PMC1HR_APP_GPIO_1_MMC;
- writew(val, U300_SYSCON_VBASE + U300_SYSCON_PMC1HR);
-}
-
-void pmx_set_mission_mode_spi(void)
-{
- u16 val;
-
- /* Set up padmuxing so the SPI port and its chipselects are active */
- val = readw(U300_SYSCON_VBASE + U300_SYSCON_PMC1HR);
- /*
- * Activate the SPI port (disable the use of these pins for generic
- * GPIO, DSP, AAIF
- */
- val &= ~U300_SYSCON_PMC1HR_APP_SPI_2_MASK;
- val |= U300_SYSCON_PMC1HR_APP_SPI_2_SPI;
- /*
- * Use GPIO pin SPI CS1 for CS1 actually (it can be used for other
- * things also)
- */
- val &= ~U300_SYSCON_PMC1HR_APP_SPI_CS_1_MASK;
- val |= U300_SYSCON_PMC1HR_APP_SPI_CS_1_SPI;
- /*
- * Use GPIO pin SPI CS2 for CS2 actually (it can be used for other
- * things also)
- */
- val &= ~U300_SYSCON_PMC1HR_APP_SPI_CS_2_MASK;
- val |= U300_SYSCON_PMC1HR_APP_SPI_CS_2_SPI;
- writew(val, U300_SYSCON_VBASE + U300_SYSCON_PMC1HR);
+static DEFINE_MUTEX(pmx_mutex);
+
+const u32 pmx_registers[] = {
+ (U300_SYSCON_VBASE + U300_SYSCON_PMC1LR),
+ (U300_SYSCON_VBASE + U300_SYSCON_PMC1HR),
+ (U300_SYSCON_VBASE + U300_SYSCON_PMC2R),
+ (U300_SYSCON_VBASE + U300_SYSCON_PMC3R),
+ (U300_SYSCON_VBASE + U300_SYSCON_PMC4R)
+};
+
+/* High level functionality */
+
+/* Lazy dog:
+ * onmask = {
+ * {"PMC1LR" mask, "PMC1LR" value},
+ * {"PMC1HR" mask, "PMC1HR" value},
+ * {"PMC2R" mask, "PMC2R" value},
+ * {"PMC3R" mask, "PMC3R" value},
+ * {"PMC4R" mask, "PMC4R" value}
+ * }
+ */
+static struct pmx mmc_setting = {
+ .setting = U300_APP_PMX_MMC_SETTING,
+ .default_on = false,
+ .activated = false,
+ .name = "MMC",
+ .onmask = {
+ {U300_SYSCON_PMC1LR_MMCSD_MASK,
+ U300_SYSCON_PMC1LR_MMCSD_MMCSD},
+ {0, 0},
+ {0, 0},
+ {0, 0},
+ {U300_SYSCON_PMC4R_APP_MISC_12_MASK,
+ U300_SYSCON_PMC4R_APP_MISC_12_APP_GPIO}
+ },
+};
+
+static struct pmx spi_setting = {
+ .setting = U300_APP_PMX_SPI_SETTING,
+ .default_on = false,
+ .activated = false,
+ .name = "SPI",
+ .onmask = {{0, 0},
+ {U300_SYSCON_PMC1HR_APP_SPI_2_MASK |
+ U300_SYSCON_PMC1HR_APP_SPI_CS_1_MASK |
+ U300_SYSCON_PMC1HR_APP_SPI_CS_2_MASK,
+ U300_SYSCON_PMC1HR_APP_SPI_2_SPI |
+ U300_SYSCON_PMC1HR_APP_SPI_CS_1_SPI |
+ U300_SYSCON_PMC1HR_APP_SPI_CS_2_SPI},
+ {0, 0},
+ {0, 0},
+ {0, 0}
+ },
+};
+
+/* Available padmux settings */
+static struct pmx *pmx_settings[] = {
+ &mmc_setting,
+ &spi_setting,
+};
+
+static void update_registers(struct pmx *pmx, bool activate)
+{
+ u16 regval, val, mask;
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(pmx_registers); i++) {
+ if (activate)
+ val = pmx->onmask[i].val;
+ else
+ val = 0;
+
+ mask = pmx->onmask[i].mask;
+ if (mask != 0) {
+ regval = readw(pmx_registers[i]);
+ regval &= ~mask;
+ regval |= val;
+ writew(regval, pmx_registers[i]);
+ }
+ }
+}
+
+struct pmx *pmx_get(struct device *dev, enum pmx_settings setting)
+{
+ int i;
+ struct pmx *pmx = ERR_PTR(-ENOENT);
+
+ if (dev == NULL)
+ return ERR_PTR(-EINVAL);
+
+ mutex_lock(&pmx_mutex);
+ for (i = 0; i < ARRAY_SIZE(pmx_settings); i++) {
+
+ if (setting == pmx_settings[i]->setting) {
+
+ if (pmx_settings[i]->dev != NULL) {
+ WARN(1, "padmux: required setting "
+ "in use by another consumer\n");
+ } else {
+ pmx = pmx_settings[i];
+ pmx->dev = dev;
+ dev_dbg(dev, "padmux: setting nr %d is now "
+ "bound to %s and ready to use\n",
+ setting, dev_name(dev));
+ break;
+ }
+ }
+ }
+ mutex_unlock(&pmx_mutex);
+
+ return pmx;
+}
+EXPORT_SYMBOL(pmx_get);
+
+int pmx_put(struct device *dev, struct pmx *pmx)
+{
+ int i;
+ int ret = -ENOENT;
+
+ if (pmx == NULL || dev == NULL)
+ return -EINVAL;
+
+ mutex_lock(&pmx_mutex);
+ for (i = 0; i < ARRAY_SIZE(pmx_settings); i++) {
+
+ if (pmx->setting == pmx_settings[i]->setting) {
+
+ if (dev != pmx->dev) {
+ WARN(1, "padmux: cannot release handle as "
+ "it is bound to another consumer\n");
+ ret = -EINVAL;
+ break;
+ } else {
+ pmx_settings[i]->dev = NULL;
+ ret = 0;
+ break;
+ }
+ }
+ }
+ mutex_unlock(&pmx_mutex);
+
+ return ret;
+}
+EXPORT_SYMBOL(pmx_put);
+
+int pmx_activate(struct device *dev, struct pmx *pmx)
+{
+ int i, j, ret;
+ ret = 0;
+
+ if (pmx == NULL || dev == NULL)
+ return -EINVAL;
+
+ mutex_lock(&pmx_mutex);
+
+ /* Make sure the required bits are not used */
+ for (i = 0; i < ARRAY_SIZE(pmx_settings); i++) {
+
+ if (pmx_settings[i]->dev == NULL || pmx_settings[i] == pmx)
+ continue;
+
+ for (j = 0; j < ARRAY_SIZE(pmx_registers); j++) {
+
+ if (pmx_settings[i]->onmask[j].mask & pmx->
+ onmask[j].mask) {
+ /* More than one entry on the same bits */
+ WARN(1, "padmux: cannot activate "
+ "setting. Bit conflict with "
+ "an active setting\n");
+
+ ret = -EUSERS;
+ goto exit;
+ }
+ }
+ }
+ update_registers(pmx, true);
+ pmx->activated = true;
+ dev_dbg(dev, "padmux: setting nr %d is activated\n",
+ pmx->setting);
+
+exit:
+ mutex_unlock(&pmx_mutex);
+ return ret;
+}
+EXPORT_SYMBOL(pmx_activate);
+
+int pmx_deactivate(struct device *dev, struct pmx *pmx)
+{
+ int i;
+ int ret = -ENOENT;
+
+ if (pmx == NULL || dev == NULL)
+ return -EINVAL;
+
+ mutex_lock(&pmx_mutex);
+ for (i = 0; i < ARRAY_SIZE(pmx_settings); i++) {
+
+ if (pmx_settings[i]->dev == NULL)
+ continue;
+
+ if (pmx->setting == pmx_settings[i]->setting) {
+
+ if (dev != pmx->dev) {
+ WARN(1, "padmux: cannot deactivate "
+ "pmx setting as it was activated "
+ "by another consumer\n");
+
+ ret = -EBUSY;
+ continue;
+ } else {
+ update_registers(pmx, false);
+ pmx_settings[i]->dev = NULL;
+ pmx->activated = false;
+ ret = 0;
+ dev_dbg(dev, "padmux: setting nr %d is deactivated",
+ pmx->setting);
+ break;
+ }
+ }
+ }
+ mutex_unlock(&pmx_mutex);
+
+ return ret;
+}
+EXPORT_SYMBOL(pmx_deactivate);
+
+/*
+ * For internal use only. If it is to be exported,
+ * it should be reentrant. Notice that pmx_activate
+ * (i.e. runtime settings) always override default settings.
+ */
+static int pmx_set_default(void)
+{
+ /* Used to identify several entries on the same bits */
+ u16 modbits[ARRAY_SIZE(pmx_registers)];
+
+ int i, j;
+
+ memset(modbits, 0, ARRAY_SIZE(pmx_registers) * sizeof(u16));
+
+ for (i = 0; i < ARRAY_SIZE(pmx_settings); i++) {
+
+ if (!pmx_settings[i]->default_on)
+ continue;
+
+ for (j = 0; j < ARRAY_SIZE(pmx_registers); j++) {
+
+ /* Make sure there is only one entry on the same bits */
+ if (modbits[j] & pmx_settings[i]->onmask[j].mask) {
+ BUG();
+ return -EUSERS;
+ }
+ modbits[j] |= pmx_settings[i]->onmask[j].mask;
+ }
+ update_registers(pmx_settings[i], true);
+ }
+ return 0;
}
+
+#if (defined(CONFIG_DEBUG_FS) && defined(CONFIG_U300_DEBUG))
+static int pmx_show(struct seq_file *s, void *data)
+{
+ int i;
+ seq_printf(s, "-------------------------------------------------\n");
+ seq_printf(s, "SETTING BOUND TO DEVICE STATE\n");
+ seq_printf(s, "-------------------------------------------------\n");
+ mutex_lock(&pmx_mutex);
+ for (i = 0; i < ARRAY_SIZE(pmx_settings); i++) {
+ /* Format pmx and device name nicely */
+ char cdp[33];
+ int chars;
+
+ chars = snprintf(&cdp[0], 17, "%s", pmx_settings[i]->name);
+ while (chars < 16) {
+ cdp[chars] = ' ';
+ chars++;
+ }
+ chars = snprintf(&cdp[16], 17, "%s", pmx_settings[i]->dev ?
+ dev_name(pmx_settings[i]->dev) : "N/A");
+ while (chars < 16) {
+ cdp[chars+16] = ' ';
+ chars++;
+ }
+ cdp[32] = '\0';
+
+ seq_printf(s,
+ "%s\t%s\n",
+ &cdp[0],
+ pmx_settings[i]->activated ?
+ "ACTIVATED" : "DEACTIVATED"
+ );
+
+ }
+ mutex_unlock(&pmx_mutex);
+ return 0;
+}
+
+static int pmx_open(struct inode *inode, struct file *file)
+{
+ return single_open(file, pmx_show, NULL);
+}
+
+static const struct file_operations pmx_operations = {
+ .owner = THIS_MODULE,
+ .open = pmx_open,
+ .read = seq_read,
+ .llseek = seq_lseek,
+ .release = single_release,
+};
+
+static int __init init_pmx_read_debugfs(void)
+{
+ /* Expose a simple debugfs interface to view pmx settings */
+ (void) debugfs_create_file("padmux", S_IFREG | S_IRUGO,
+ NULL, NULL,
+ &pmx_operations);
+ return 0;
+}
+
+/*
+ * This needs to come in after the core_initcall(),
+ * because debugfs is not available until
+ * the subsystems come up.
+ */
+module_init(init_pmx_read_debugfs);
+#endif
+
+static int __init pmx_init(void)
+{
+ int ret;
+
+ ret = pmx_set_default();
+
+ if (IS_ERR_VALUE(ret))
+ pr_crit("padmux: default settings could not be set\n");
+
+ return 0;
+}
+
+/* Should be initialized before consumers */
+core_initcall(pmx_init);
* Copyright (C) 2009 ST-Ericsson AB
* License terms: GNU General Public License (GPL) version 2
* U300 PADMUX API
- * Author: Linus Walleij <linus.walleij@stericsson.com>
- *
+ * Author: Martin Persson <martin.persson@stericsson.com>
*/
#ifndef __MACH_U300_PADMUX_H
#define __MACH_U300_PADMUX_H
-void pmx_set_mission_mode_mmc(void);
-void pmx_set_mission_mode_spi(void);
+enum pmx_settings {
+ U300_APP_PMX_MMC_SETTING,
+ U300_APP_PMX_SPI_SETTING
+};
+
+struct pmx_onmask {
+ u16 mask; /* Mask bits */
+ u16 val; /* Value when active */
+};
+
+struct pmx {
+ struct device *dev;
+ enum pmx_settings setting;
+ char *name;
+ bool activated;
+ bool default_on;
+ struct pmx_onmask onmask[];
+};
+
+struct pmx *pmx_get(struct device *dev, enum pmx_settings setting);
+int pmx_put(struct device *dev, struct pmx *pmx);
+int pmx_activate(struct device *dev, struct pmx *pmx);
+int pmx_deactivate(struct device *dev, struct pmx *pmx);
#endif
--- /dev/null
+/*
+ * arch/arm/mach-u300/spi.c
+ *
+ * Copyright (C) 2009 ST-Ericsson AB
+ * License terms: GNU General Public License (GPL) version 2
+ *
+ * Author: Linus Walleij <linus.walleij@stericsson.com>
+ */
+#include <linux/device.h>
+#include <linux/amba/bus.h>
+#include <linux/spi/spi.h>
+#include <linux/amba/pl022.h>
+#include <linux/err.h>
+#include "padmux.h"
+
+/*
+ * The following is for the actual devices on the SSP/SPI bus
+ */
+#ifdef CONFIG_MACH_U300_SPIDUMMY
+static void select_dummy_chip(u32 chipselect)
+{
+ pr_debug("CORE: %s called with CS=0x%x (%s)\n",
+ __func__,
+ chipselect,
+ chipselect ? "unselect chip" : "select chip");
+ /*
+ * Here you would write the chip select value to the GPIO pins if
+ * this was a real chip (but this is a loopback dummy).
+ */
+}
+
+struct pl022_config_chip dummy_chip_info = {
+ /* Nominally this is LOOPBACK_DISABLED, but this is our dummy chip! */
+ .lbm = LOOPBACK_ENABLED,
+ /*
+ * available POLLING_TRANSFER and INTERRUPT_TRANSFER,
+ * DMA_TRANSFER does not work
+ */
+ .com_mode = INTERRUPT_TRANSFER,
+ .iface = SSP_INTERFACE_MOTOROLA_SPI,
+ /* We can only act as master but SSP_SLAVE is possible in theory */
+ .hierarchy = SSP_MASTER,
+ /* 0 = drive TX even as slave, 1 = do not drive TX as slave */
+ .slave_tx_disable = 0,
+ /* LSB first */
+ .endian_tx = SSP_TX_LSB,
+ .endian_rx = SSP_RX_LSB,
+ .data_size = SSP_DATA_BITS_8, /* used to be 12 in some default */
+ .rx_lev_trig = SSP_RX_1_OR_MORE_ELEM,
+ .tx_lev_trig = SSP_TX_1_OR_MORE_EMPTY_LOC,
+ .clk_phase = SSP_CLK_SECOND_EDGE,
+ .clk_pol = SSP_CLK_POL_IDLE_LOW,
+ .ctrl_len = SSP_BITS_12,
+ .wait_state = SSP_MWIRE_WAIT_ZERO,
+ .duplex = SSP_MICROWIRE_CHANNEL_FULL_DUPLEX,
+ /*
+ * This is where you insert a call to a function to enable CS
+ * (usually GPIO) for a certain chip.
+ */
+ .cs_control = select_dummy_chip,
+};
+#endif
+
+static struct spi_board_info u300_spi_devices[] = {
+#ifdef CONFIG_MACH_U300_SPIDUMMY
+ {
+ /* A dummy chip used for loopback tests */
+ .modalias = "spi-dummy",
+ /* Really dummy, pass in additional chip config here */
+ .platform_data = NULL,
+ /* This defines how the controller shall handle the device */
+ .controller_data = &dummy_chip_info,
+ /* .irq - no external IRQ routed from this device */
+ .max_speed_hz = 1000000,
+ .bus_num = 0, /* Only one bus on this chip */
+ .chip_select = 0,
+ /* Means SPI_CS_HIGH, change if e.g low CS */
+ .mode = 0,
+ },
+#endif
+};
+
+static struct pl022_ssp_controller ssp_platform_data = {
+ /* If you have several SPI buses this varies, we have only bus 0 */
+ .bus_id = 0,
+ /* Set this to 1 when we think we got DMA working */
+ .enable_dma = 0,
+ /*
+ * On the APP CPU GPIO 4, 5 and 6 are connected as generic
+ * chip selects for SPI. (Same on U330, U335 and U365.)
+ * TODO: make sure the GPIO driver can select these properly
+ * and do padmuxing accordingly too.
+ */
+ .num_chipselect = 3,
+};
+
+
+void __init u300_spi_init(struct amba_device *adev)
+{
+ struct pmx *pmx;
+
+ adev->dev.platform_data = &ssp_platform_data;
+ /*
+ * Setup padmuxing for SPI. Since this must always be
+ * compiled into the kernel, pmx is never released.
+ */
+ pmx = pmx_get(&adev->dev, U300_APP_PMX_SPI_SETTING);
+
+ if (IS_ERR(pmx))
+ dev_warn(&adev->dev, "Could not get padmux handle\n");
+ else {
+ int ret;
+
+ ret = pmx_activate(&adev->dev, pmx);
+ if (IS_ERR_VALUE(ret))
+ dev_warn(&adev->dev, "Could not activate padmuxing\n");
+ }
+
+}
+void __init u300_spi_register_board_devices(void)
+{
+ /* Register any SPI devices */
+ spi_register_board_info(u300_spi_devices, ARRAY_SIZE(u300_spi_devices));
+}
--- /dev/null
+/*
+ * arch/arm/mach-u300/spi.h
+ *
+ * Copyright (C) 2009 ST-Ericsson AB
+ * License terms: GNU General Public License (GPL) version 2
+ *
+ * Author: Linus Walleij <linus.walleij@stericsson.com>
+ */
+#ifndef SPI_H
+#define SPI_H
+#include <linux/amba/bus.h>
+
+#ifdef CONFIG_SPI_PL022
+void __init u300_spi_init(struct amba_device *adev);
+void __init u300_spi_register_board_devices(void);
+#else
+/* Compile out SPI support if PL022 is not selected */
+static inline void __init u300_spi_init(struct amba_device *adev)
+{
+}
+static inline void __init u300_spi_register_board_devices(void)
+{
+}
+#endif
+
+#endif
.flags = CLOCK_SOURCE_IS_CONTINUOUS,
};
+/*
+ * Override the global weak sched_clock symbol with this
+ * local implementation which uses the clocksource to get some
+ * better resolution when scheduling the kernel. We accept that
+ * this wraps around for now, since it is just a relative time
+ * stamp. (Inspired by OMAP implementation.)
+ */
+unsigned long long notrace sched_clock(void)
+{
+ return clocksource_cyc2ns(clocksource_u300_1mhz.read(
+ &clocksource_u300_1mhz),
+ clocksource_u300_1mhz.mult,
+ clocksource_u300_1mhz.shift);
+}
+
/*
* This sets up the system timers, clock source and clock event.
#include <linux/amba/bus.h>
#include <linux/amba/clcd.h>
#include <linux/amba/pl061.h>
+#include <linux/amba/mmci.h>
#include <linux/clocksource.h>
#include <linux/clockchips.h>
#include <linux/cnt32_to_63.h>
#include <asm/mach/irq.h>
#include <asm/mach/time.h>
#include <asm/mach/map.h>
-#include <asm/mach/mmc.h>
#include "core.h"
#include "clock.h"
return readl(VERSATILE_SYSMCI) & mask;
}
-static struct mmc_platform_data mmc0_plat_data = {
+static struct mmci_platform_data mmc0_plat_data = {
.ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
.status = mmc_status,
.gpio_wp = -1,
#include <linux/sysdev.h>
#include <linux/amba/bus.h>
#include <linux/amba/pl061.h>
+#include <linux/amba/mmci.h>
#include <linux/io.h>
#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
-#include <asm/mach/mmc.h>
#include "core.h"
#define IRQ_MMCI1A IRQ_SIC_MMCI1A
#endif
-static struct mmc_platform_data mmc1_plat_data = {
+static struct mmci_platform_data mmc1_plat_data = {
.ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
.status = mmc_status,
.gpio_wp = -1,
select OUTER_CACHE
help
This option enables the L2 cache on XScale3.
+
+config ARM_L1_CACHE_SHIFT
+ int
+ default 6 if ARCH_OMAP3
+ default 5
#include "fault.h"
+/*
+ * Fault status register encodings. We steal bit 31 for our own purposes.
+ */
+#define FSR_LNX_PF (1 << 31)
+#define FSR_WRITE (1 << 11)
+#define FSR_FS4 (1 << 10)
+#define FSR_FS3_0 (15)
+
+static inline int fsr_fs(unsigned int fsr)
+{
+ return (fsr & FSR_FS3_0) | (fsr & FSR_FS4) >> 6;
+}
+
#ifdef CONFIG_MMU
#ifdef CONFIG_KPROBES
#define VM_FAULT_BADMAP 0x010000
#define VM_FAULT_BADACCESS 0x020000
-static int
+/*
+ * Check that the permissions on the VMA allow for the fault which occurred.
+ * If we encountered a write fault, we must have write permission, otherwise
+ * we allow any permission.
+ */
+static inline bool access_error(unsigned int fsr, struct vm_area_struct *vma)
+{
+ unsigned int mask = VM_READ | VM_WRITE | VM_EXEC;
+
+ if (fsr & FSR_WRITE)
+ mask = VM_WRITE;
+ if (fsr & FSR_LNX_PF)
+ mask = VM_EXEC;
+
+ return vma->vm_flags & mask ? false : true;
+}
+
+static int __kprobes
__do_page_fault(struct mm_struct *mm, unsigned long addr, unsigned int fsr,
struct task_struct *tsk)
{
struct vm_area_struct *vma;
- int fault, mask;
+ int fault;
vma = find_vma(mm, addr);
fault = VM_FAULT_BADMAP;
- if (!vma)
+ if (unlikely(!vma))
goto out;
- if (vma->vm_start > addr)
+ if (unlikely(vma->vm_start > addr))
goto check_stack;
/*
* memory access, so we can handle it.
*/
good_area:
- if (fsr & (1 << 11)) /* write? */
- mask = VM_WRITE;
- else
- mask = VM_READ|VM_EXEC|VM_WRITE;
-
- fault = VM_FAULT_BADACCESS;
- if (!(vma->vm_flags & mask))
+ if (access_error(fsr, vma)) {
+ fault = VM_FAULT_BADACCESS;
goto out;
+ }
/*
- * If for any reason at all we couldn't handle
- * the fault, make sure we exit gracefully rather
- * than endlessly redo the fault.
+ * If for any reason at all we couldn't handle the fault, make
+ * sure we exit gracefully rather than endlessly redo the fault.
*/
-survive:
- fault = handle_mm_fault(mm, vma, addr & PAGE_MASK, (fsr & (1 << 11)) ? FAULT_FLAG_WRITE : 0);
- if (unlikely(fault & VM_FAULT_ERROR)) {
- if (fault & VM_FAULT_OOM)
- goto out_of_memory;
- else if (fault & VM_FAULT_SIGBUS)
- return fault;
- BUG();
- }
+ fault = handle_mm_fault(mm, vma, addr & PAGE_MASK, (fsr & FSR_WRITE) ? FAULT_FLAG_WRITE : 0);
+ if (unlikely(fault & VM_FAULT_ERROR))
+ return fault;
if (fault & VM_FAULT_MAJOR)
tsk->maj_flt++;
else
tsk->min_flt++;
return fault;
-out_of_memory:
- if (!is_global_init(tsk))
- goto out;
-
- /*
- * If we are out of memory for pid1, sleep for a while and retry
- */
- up_read(&mm->mmap_sem);
- yield();
- down_read(&mm->mmap_sem);
- goto survive;
-
check_stack:
if (vma->vm_flags & VM_GROWSDOWN && !expand_stack(vma, addr))
goto good_area;
if (!user_mode(regs) && !search_exception_tables(regs->ARM_pc))
goto no_context;
down_read(&mm->mmap_sem);
+ } else {
+ /*
+ * The above down_read_trylock() might have succeeded in
+ * which case, we'll have missed the might_sleep() from
+ * down_read()
+ */
+ might_sleep();
}
fault = __do_page_fault(mm, addr, fsr, tsk);
if (likely(!(fault & (VM_FAULT_ERROR | VM_FAULT_BADMAP | VM_FAULT_BADACCESS))))
return 0;
+ if (fault & VM_FAULT_OOM) {
+ /*
+ * We ran out of memory, call the OOM killer, and return to
+ * userspace (which will retry the fault, or kill us if we
+ * got oom-killed)
+ */
+ pagefault_out_of_memory();
+ return 0;
+ }
+
/*
* If we are in kernel mode at this point, we
* have no context to handle this fault with.
if (!user_mode(regs))
goto no_context;
- if (fault & VM_FAULT_OOM) {
- /*
- * We ran out of memory, or some other thing
- * happened to us that made us unable to handle
- * the page fault gracefully.
- */
- printk("VM: killing process %s\n", tsk->comm);
- do_group_exit(SIGKILL);
- return 0;
- }
if (fault & VM_FAULT_SIGBUS) {
/*
* We had some memory, but were unable to
asmlinkage void __exception
do_DataAbort(unsigned long addr, unsigned int fsr, struct pt_regs *regs)
{
- const struct fsr_info *inf = fsr_info + (fsr & 15) + ((fsr & (1 << 10)) >> 6);
+ const struct fsr_info *inf = fsr_info + fsr_fs(fsr);
struct siginfo info;
- if (!inf->fn(addr, fsr, regs))
+ if (!inf->fn(addr, fsr & ~FSR_LNX_PF, regs))
return;
printk(KERN_ALERT "Unhandled fault: %s (0x%03x) at 0x%08lx\n",
asmlinkage void __exception
do_PrefetchAbort(unsigned long addr, struct pt_regs *regs)
{
- do_translation_fault(addr, 0, regs);
+ do_translation_fault(addr, FSR_LNX_PF, regs);
}
void free_initmem(void)
{
+#ifdef CONFIG_HAVE_TCM
+ extern char *__tcm_start, *__tcm_end;
+
+ totalram_pages += free_area(__phys_to_pfn(__pa(__tcm_start)),
+ __phys_to_pfn(__pa(__tcm_end)),
+ "TCM link");
+#endif
+
if (!machine_is_integrator() && !machine_is_cintegrator())
totalram_pages += free_area(__phys_to_pfn(__pa(__init_begin)),
__phys_to_pfn(__pa(__init_end)),
#include <linux/kernel.h>
#include <linux/interrupt.h>
#include <linux/errno.h>
+#include <linux/dma-mapping.h>
#include <asm/system.h>
#include <asm/irq.h>
+#include <asm/memory.h>
#include <mach/hardware.h>
#include <mach/dma.h>
+#define DMA_DEBUG_NAME "pxa_dma"
+#define DMA_MAX_REQUESTERS 64
+
struct dma_channel {
char *name;
pxa_dma_prio prio;
void (*irq_handler)(int, void *);
void *data;
+ spinlock_t lock;
};
static struct dma_channel *dma_channels;
static int num_dma_channels;
+/*
+ * Debug fs
+ */
+#ifdef CONFIG_DEBUG_FS
+#include <linux/debugfs.h>
+#include <linux/uaccess.h>
+#include <linux/seq_file.h>
+
+static struct dentry *dbgfs_root, *dbgfs_state, **dbgfs_chan;
+
+static int dbg_show_requester_chan(struct seq_file *s, void *p)
+{
+ int pos = 0;
+ int chan = (int)s->private;
+ int i;
+ u32 drcmr;
+
+ pos += seq_printf(s, "DMA channel %d requesters list :\n", chan);
+ for (i = 0; i < DMA_MAX_REQUESTERS; i++) {
+ drcmr = DRCMR(i);
+ if ((drcmr & DRCMR_CHLNUM) == chan)
+ pos += seq_printf(s, "\tRequester %d (MAPVLD=%d)\n", i,
+ !!(drcmr & DRCMR_MAPVLD));
+ }
+ return pos;
+}
+
+static inline int dbg_burst_from_dcmd(u32 dcmd)
+{
+ int burst = (dcmd >> 16) & 0x3;
+
+ return burst ? 4 << burst : 0;
+}
+
+static int is_phys_valid(unsigned long addr)
+{
+ return pfn_valid(__phys_to_pfn(addr));
+}
+
+#define DCSR_STR(flag) (dcsr & DCSR_##flag ? #flag" " : "")
+#define DCMD_STR(flag) (dcmd & DCMD_##flag ? #flag" " : "")
+
+static int dbg_show_descriptors(struct seq_file *s, void *p)
+{
+ int pos = 0;
+ int chan = (int)s->private;
+ int i, max_show = 20, burst, width;
+ u32 dcmd;
+ unsigned long phys_desc;
+ struct pxa_dma_desc *desc;
+ unsigned long flags;
+
+ spin_lock_irqsave(&dma_channels[chan].lock, flags);
+ phys_desc = DDADR(chan);
+
+ pos += seq_printf(s, "DMA channel %d descriptors :\n", chan);
+ pos += seq_printf(s, "[%03d] First descriptor unknown\n", 0);
+ for (i = 1; i < max_show && is_phys_valid(phys_desc); i++) {
+ desc = phys_to_virt(phys_desc);
+ dcmd = desc->dcmd;
+ burst = dbg_burst_from_dcmd(dcmd);
+ width = (1 << ((dcmd >> 14) & 0x3)) >> 1;
+
+ pos += seq_printf(s, "[%03d] Desc at %08lx(virt %p)\n",
+ i, phys_desc, desc);
+ pos += seq_printf(s, "\tDDADR = %08x\n", desc->ddadr);
+ pos += seq_printf(s, "\tDSADR = %08x\n", desc->dsadr);
+ pos += seq_printf(s, "\tDTADR = %08x\n", desc->dtadr);
+ pos += seq_printf(s, "\tDCMD = %08x (%s%s%s%s%s%s%sburst=%d"
+ " width=%d len=%d)\n",
+ dcmd,
+ DCMD_STR(INCSRCADDR), DCMD_STR(INCTRGADDR),
+ DCMD_STR(FLOWSRC), DCMD_STR(FLOWTRG),
+ DCMD_STR(STARTIRQEN), DCMD_STR(ENDIRQEN),
+ DCMD_STR(ENDIAN), burst, width,
+ dcmd & DCMD_LENGTH);
+ phys_desc = desc->ddadr;
+ }
+ if (i == max_show)
+ pos += seq_printf(s, "[%03d] Desc at %08lx ... max display reached\n",
+ i, phys_desc);
+ else
+ pos += seq_printf(s, "[%03d] Desc at %08lx is %s\n",
+ i, phys_desc, phys_desc == DDADR_STOP ?
+ "DDADR_STOP" : "invalid");
+
+ spin_unlock_irqrestore(&dma_channels[chan].lock, flags);
+ return pos;
+}
+
+static int dbg_show_chan_state(struct seq_file *s, void *p)
+{
+ int pos = 0;
+ int chan = (int)s->private;
+ u32 dcsr, dcmd;
+ int burst, width;
+ static char *str_prio[] = { "high", "normal", "low" };
+
+ dcsr = DCSR(chan);
+ dcmd = DCMD(chan);
+ burst = dbg_burst_from_dcmd(dcmd);
+ width = (1 << ((dcmd >> 14) & 0x3)) >> 1;
+
+ pos += seq_printf(s, "DMA channel %d\n", chan);
+ pos += seq_printf(s, "\tPriority : %s\n",
+ str_prio[dma_channels[chan].prio]);
+ pos += seq_printf(s, "\tUnaligned transfer bit: %s\n",
+ DALGN & (1 << chan) ? "yes" : "no");
+ pos += seq_printf(s, "\tDCSR = %08x (%s%s%s%s%s%s%s%s%s%s%s%s%s%s%s)\n",
+ dcsr, DCSR_STR(RUN), DCSR_STR(NODESC),
+ DCSR_STR(STOPIRQEN), DCSR_STR(EORIRQEN),
+ DCSR_STR(EORJMPEN), DCSR_STR(EORSTOPEN),
+ DCSR_STR(SETCMPST), DCSR_STR(CLRCMPST),
+ DCSR_STR(CMPST), DCSR_STR(EORINTR), DCSR_STR(REQPEND),
+ DCSR_STR(STOPSTATE), DCSR_STR(ENDINTR),
+ DCSR_STR(STARTINTR), DCSR_STR(BUSERR));
+
+ pos += seq_printf(s, "\tDCMD = %08x (%s%s%s%s%s%s%sburst=%d width=%d"
+ " len=%d)\n",
+ dcmd,
+ DCMD_STR(INCSRCADDR), DCMD_STR(INCTRGADDR),
+ DCMD_STR(FLOWSRC), DCMD_STR(FLOWTRG),
+ DCMD_STR(STARTIRQEN), DCMD_STR(ENDIRQEN),
+ DCMD_STR(ENDIAN), burst, width, dcmd & DCMD_LENGTH);
+ pos += seq_printf(s, "\tDSADR = %08x\n", DSADR(chan));
+ pos += seq_printf(s, "\tDTADR = %08x\n", DTADR(chan));
+ pos += seq_printf(s, "\tDDADR = %08x\n", DDADR(chan));
+ return pos;
+}
+
+static int dbg_show_state(struct seq_file *s, void *p)
+{
+ int pos = 0;
+
+ /* basic device status */
+ pos += seq_printf(s, "DMA engine status\n");
+ pos += seq_printf(s, "\tChannel number: %d\n", num_dma_channels);
+
+ return pos;
+}
+
+#define DBGFS_FUNC_DECL(name) \
+static int dbg_open_##name(struct inode *inode, struct file *file) \
+{ \
+ return single_open(file, dbg_show_##name, inode->i_private); \
+} \
+static const struct file_operations dbg_fops_##name = { \
+ .owner = THIS_MODULE, \
+ .open = dbg_open_##name, \
+ .llseek = seq_lseek, \
+ .read = seq_read, \
+ .release = single_release, \
+}
+
+DBGFS_FUNC_DECL(state);
+DBGFS_FUNC_DECL(chan_state);
+DBGFS_FUNC_DECL(descriptors);
+DBGFS_FUNC_DECL(requester_chan);
+
+static struct dentry *pxa_dma_dbg_alloc_chan(int ch, struct dentry *chandir)
+{
+ char chan_name[11];
+ struct dentry *chan, *chan_state = NULL, *chan_descr = NULL;
+ struct dentry *chan_reqs = NULL;
+ void *dt;
+
+ scnprintf(chan_name, sizeof(chan_name), "%d", ch);
+ chan = debugfs_create_dir(chan_name, chandir);
+ dt = (void *)ch;
+
+ if (chan)
+ chan_state = debugfs_create_file("state", 0400, chan, dt,
+ &dbg_fops_chan_state);
+ if (chan_state)
+ chan_descr = debugfs_create_file("descriptors", 0400, chan, dt,
+ &dbg_fops_descriptors);
+ if (chan_descr)
+ chan_reqs = debugfs_create_file("requesters", 0400, chan, dt,
+ &dbg_fops_requester_chan);
+ if (!chan_reqs)
+ goto err_state;
+
+ return chan;
+
+err_state:
+ debugfs_remove_recursive(chan);
+ return NULL;
+}
+
+static void pxa_dma_init_debugfs(void)
+{
+ int i;
+ struct dentry *chandir;
+
+ dbgfs_root = debugfs_create_dir(DMA_DEBUG_NAME, NULL);
+ if (IS_ERR(dbgfs_root) || !dbgfs_root)
+ goto err_root;
+
+ dbgfs_state = debugfs_create_file("state", 0400, dbgfs_root, NULL,
+ &dbg_fops_state);
+ if (!dbgfs_state)
+ goto err_state;
+
+ dbgfs_chan = kmalloc(sizeof(*dbgfs_state) * num_dma_channels,
+ GFP_KERNEL);
+ if (!dbgfs_state)
+ goto err_alloc;
+
+ chandir = debugfs_create_dir("channels", dbgfs_root);
+ if (!chandir)
+ goto err_chandir;
+
+ for (i = 0; i < num_dma_channels; i++) {
+ dbgfs_chan[i] = pxa_dma_dbg_alloc_chan(i, chandir);
+ if (!dbgfs_chan[i])
+ goto err_chans;
+ }
+
+ return;
+err_chans:
+err_chandir:
+ kfree(dbgfs_chan);
+err_alloc:
+err_state:
+ debugfs_remove_recursive(dbgfs_root);
+err_root:
+ pr_err("pxa_dma: debugfs is not available\n");
+}
+
+static void __exit pxa_dma_cleanup_debugfs(void)
+{
+ debugfs_remove_recursive(dbgfs_root);
+}
+#else
+static inline void pxa_dma_init_debugfs(void) {}
+static inline void pxa_dma_cleanup_debugfs(void) {}
+#endif
+
int pxa_request_dma (char *name, pxa_dma_prio prio,
void (*irq_handler)(int, void *),
void *data)
local_irq_restore(flags);
return i;
}
+EXPORT_SYMBOL(pxa_request_dma);
void pxa_free_dma (int dma_ch)
{
dma_channels[dma_ch].name = NULL;
local_irq_restore(flags);
}
+EXPORT_SYMBOL(pxa_free_dma);
static irqreturn_t dma_irq_handler(int irq, void *dev_id)
{
int i, dint = DINT;
+ struct dma_channel *channel;
- for (i = 0; i < num_dma_channels; i++) {
- if (dint & (1 << i)) {
- struct dma_channel *channel = &dma_channels[i];
- if (channel->name && channel->irq_handler) {
- channel->irq_handler(i, channel->data);
- } else {
- /*
- * IRQ for an unregistered DMA channel:
- * let's clear the interrupts and disable it.
- */
- printk (KERN_WARNING "spurious IRQ for DMA channel %d\n", i);
- DCSR(i) = DCSR_STARTINTR|DCSR_ENDINTR|DCSR_BUSERR;
- }
+ while (dint) {
+ i = __ffs(dint);
+ dint &= (dint - 1);
+ channel = &dma_channels[i];
+ if (channel->name && channel->irq_handler) {
+ channel->irq_handler(i, channel->data);
+ } else {
+ /*
+ * IRQ for an unregistered DMA channel:
+ * let's clear the interrupts and disable it.
+ */
+ printk (KERN_WARNING "spurious IRQ for DMA channel %d\n", i);
+ DCSR(i) = DCSR_STARTINTR|DCSR_ENDINTR|DCSR_BUSERR;
}
}
return IRQ_HANDLED;
for (i = 0; i < num_ch; i++) {
DCSR(i) = 0;
dma_channels[i].prio = min((i & 0xf) >> 2, DMA_PRIO_LOW);
+ spin_lock_init(&dma_channels[i].lock);
}
ret = request_irq(irq, dma_irq_handler, IRQF_DISABLED, "DMA", NULL);
kfree(dma_channels);
return ret;
}
-
num_dma_channels = num_ch;
+
+ pxa_dma_init_debugfs();
+
return 0;
}
-
-EXPORT_SYMBOL(pxa_request_dma);
-EXPORT_SYMBOL(pxa_free_dma);
MFP_PIN_GPIO125,
MFP_PIN_GPIO126,
MFP_PIN_GPIO127,
+
+ MFP_PIN_GPIO128,
+ MFP_PIN_GPIO129,
+ MFP_PIN_GPIO130,
+ MFP_PIN_GPIO131,
+ MFP_PIN_GPIO132,
+ MFP_PIN_GPIO133,
+ MFP_PIN_GPIO134,
+ MFP_PIN_GPIO135,
+ MFP_PIN_GPIO136,
+ MFP_PIN_GPIO137,
+ MFP_PIN_GPIO138,
+ MFP_PIN_GPIO139,
+ MFP_PIN_GPIO140,
+ MFP_PIN_GPIO141,
+ MFP_PIN_GPIO142,
+ MFP_PIN_GPIO143,
+ MFP_PIN_GPIO144,
+ MFP_PIN_GPIO145,
+ MFP_PIN_GPIO146,
+ MFP_PIN_GPIO147,
+ MFP_PIN_GPIO148,
+ MFP_PIN_GPIO149,
+ MFP_PIN_GPIO150,
+ MFP_PIN_GPIO151,
+ MFP_PIN_GPIO152,
+ MFP_PIN_GPIO153,
+ MFP_PIN_GPIO154,
+ MFP_PIN_GPIO155,
+ MFP_PIN_GPIO156,
+ MFP_PIN_GPIO157,
+ MFP_PIN_GPIO158,
+ MFP_PIN_GPIO159,
+ MFP_PIN_GPIO160,
+ MFP_PIN_GPIO161,
+ MFP_PIN_GPIO162,
+ MFP_PIN_GPIO163,
+ MFP_PIN_GPIO164,
+ MFP_PIN_GPIO165,
+ MFP_PIN_GPIO166,
+ MFP_PIN_GPIO167,
+ MFP_PIN_GPIO168,
+ MFP_PIN_GPIO169,
+ MFP_PIN_GPIO170,
+ MFP_PIN_GPIO171,
+ MFP_PIN_GPIO172,
+ MFP_PIN_GPIO173,
+ MFP_PIN_GPIO174,
+ MFP_PIN_GPIO175,
+ MFP_PIN_GPIO176,
+ MFP_PIN_GPIO177,
+ MFP_PIN_GPIO178,
+ MFP_PIN_GPIO179,
+ MFP_PIN_GPIO180,
+ MFP_PIN_GPIO181,
+ MFP_PIN_GPIO182,
+ MFP_PIN_GPIO183,
+ MFP_PIN_GPIO184,
+ MFP_PIN_GPIO185,
+ MFP_PIN_GPIO186,
+ MFP_PIN_GPIO187,
+ MFP_PIN_GPIO188,
+ MFP_PIN_GPIO189,
+ MFP_PIN_GPIO190,
+ MFP_PIN_GPIO191,
+
+ MFP_PIN_GPIO255 = 255,
+
MFP_PIN_GPIO0_2,
MFP_PIN_GPIO1_2,
MFP_PIN_GPIO2_2,
#define MFP_PULL_LOW (0x1 << 21)
#define MFP_PULL_HIGH (0x2 << 21)
#define MFP_PULL_BOTH (0x3 << 21)
-#define MFP_PULL_MASK (0x3 << 21)
-#define MFP_PULL(x) (((x) >> 21) & 0x3)
+#define MFP_PULL_FLOAT (0x4 << 21)
+#define MFP_PULL_MASK (0x7 << 21)
+#define MFP_PULL(x) (((x) >> 21) & 0x7)
#define MFP_CFG_DEFAULT (MFP_AF0 | MFP_DS03X | MFP_LPM_DEFAULT |\
MFP_LPM_EDGE_NONE | MFP_PULL_NONE)
* MFPR_PULL_LOW 1 0 1
* MFPR_PULL_HIGH 1 1 0
* MFPR_PULL_BOTH 1 1 1
+ * MFPR_PULL_FLOAT 1 0 0
*/
#define MFPR_PULL_NONE (0)
#define MFPR_PULL_LOW (MFPR_PULL_SEL | MFPR_PULLDOWN_EN)
#define MFPR_PULL_BOTH (MFPR_PULL_LOW | MFPR_PULLUP_EN)
#define MFPR_PULL_HIGH (MFPR_PULL_SEL | MFPR_PULLUP_EN)
+#define MFPR_PULL_FLOAT (MFPR_PULL_SEL)
/* mfp_spin_lock is used to ensure that MFP register configuration
* (most likely a read-modify-write operation) is atomic, and that
MFPR_PULL_LOW,
MFPR_PULL_HIGH,
MFPR_PULL_BOTH,
+ MFPR_PULL_FLOAT,
};
/* mapping of MFP_LPM_EDGE_* definitions to MFPR_EDGE_* register bits */
gpn = chip->chip.base;
for (i = 0; i < chip->chip.ngpio; i++, gpn++) {
- BUG_ON(gpn > ARRAY_SIZE(s3c_gpios));
+ BUG_ON(gpn >= ARRAY_SIZE(s3c_gpios));
s3c_gpios[gpn] = chip;
}
}
if (!chan)
return -EINVAL;
- buff = kzalloc(sizeof(struct s3c64xx_dma_buff), GFP_KERNEL);
+ buff = kzalloc(sizeof(struct s3c64xx_dma_buff), GFP_ATOMIC);
if (!buff) {
printk(KERN_ERR "%s: no memory for buffer\n", __func__);
return -ENOMEM;
}
- lli = dma_pool_alloc(dma_pool, GFP_KERNEL, &buff->lli_dma);
+ lli = dma_pool_alloc(dma_pool, GFP_ATOMIC, &buff->lli_dma);
if (!lli) {
printk(KERN_ERR "%s: no memory for lli\n", __func__);
ret = -ENOMEM;
printk(KERN_INFO "%s: Registering DMA channels\n", __func__);
- dma_pool = dma_pool_create("DMA-LLI", NULL, 32, 16, 0);
+ dma_pool = dma_pool_create("DMA-LLI", NULL, sizeof(struct pl080s_lli), 16, 0);
if (!dma_pool) {
printk(KERN_ERR "%s: failed to create pool\n", __func__);
return -ENOMEM;
struct s3c64xx_dma_buff *next;
void *pw;
- struct pl080_lli *lli;
+ struct pl080s_lli *lli;
dma_addr_t lli_dma;
};
#define IRQ_EINT_GROUP(group, no) (IRQ_EINT_GROUP##group##_BASE + (no))
+/* Define a group of interrupts for board-specific use (eg, for MFD
+ * interrupt controllers). */
+#define IRQ_BOARD_START (IRQ_EINT_GROUP9_BASE + IRQ_EINT_GROUP9_NR + 1)
+
+#define IRQ_BOARD_NR 16
+
+#define IRQ_BOARD_END (IRQ_BOARD_START + IRQ_BOARD_NR)
+
/* Set the default NR_IRQS */
-#define NR_IRQS (IRQ_EINT_GROUP9_BASE + IRQ_EINT_GROUP9_NR + 1)
+#define NR_IRQS (IRQ_BOARD_END + 1)
#endif /* __ASM_PLAT_S3C64XX_IRQS_H */
return -EINVAL;
val = __raw_readl(reg);
- val &= ~(0xf << sclk->shift);
- val |= (div - 1) << sclk->shift;
+ val &= ~(0xf << sclk->divider_shift);
+ val |= (div - 1) << sclk->divider_shift;
__raw_writel(val, reg);
return 0;
clksrc |= src_nr << sclk->shift;
__raw_writel(clksrc, S3C_CLK_SRC);
+
+ clk->parent = parent;
return 0;
}
if (rate > parent_rate)
rate = parent_rate;
else {
- div = rate / parent_rate;
+ div = parent_rate / rate;
if (div == 0)
div = 1;
stmp3xxx_dma_free_command(ch,
&descriptors
[i]);
- } while (i-- >= 0);
+ } while (i-- > 0);
}
return err;
}
#
# http://www.arm.linux.org.uk/developer/machines/?action=new
#
-# Last update: Sat Sep 12 12:00:16 2009
+# Last update: Fri Sep 18 21:42:00 2009
#
# machine_is_xxx CONFIG_xxxx MACH_TYPE_xxx number
#
aml_m8050 MACH_AML_M8050 AML_M8050 1644
mx35_3ds MACH_MX35_3DS MX35_3DS 1645
mars MACH_MARS MARS 1646
-ntosd_644xa MACH_NTOSD_644XA NTOSD_644XA 1647
+neuros_osd2 MACH_NEUROS_OSD2 NEUROS_OSD2 1647
badger MACH_BADGER BADGER 1648
trizeps4wl MACH_TRIZEPS4WL TRIZEPS4WL 1649
trizeps5 MACH_TRIZEPS5 TRIZEPS5 1650
zoran43xx MACH_ZORAN43XX ZORAN43XX 1660
sonix926 MACH_SONIX926 SONIX926 1661
celestialsemi MACH_CELESTIALSEMI CELESTIALSEMI 1662
-cc9m2443 MACH_CC9M2443 CC9M2443 1663
+cc9m2443js MACH_CC9M2443JS CC9M2443JS 1663
tw5334 MACH_TW5334 TW5334 1664
omap_htcartemis MACH_HTCARTEMIS HTCARTEMIS 1665
nal_hlite MACH_NAL_HLITE NAL_HLITE 1666
rd88f5181l_ge MACH_RD88F5181L_GE RD88F5181L_GE 1812
sifmain MACH_SIFMAIN SIFMAIN 1813
sam9_l9261 MACH_SAM9_L9261 SAM9_L9261 1814
-cc9m2443js MACH_CC9M2443JS CC9M2443JS 1815
+cc9m2443 MACH_CC9M2443 CC9M2443 1815
xaria300 MACH_XARIA300 XARIA300 1816
it9200 MACH_IT9200 IT9200 1817
rd88f5181l_fxo MACH_RD88F5181L_FXO RD88F5181L_FXO 1818
pss2 MACH_PSS2 PSS2 2423
davinci_apm150 MACH_DAVINCI_APM150 DAVINCI_APM150 2424
str9100 MACH_STR9100 STR9100 2425
+net5big MACH_NET5BIG NET5BIG 2426
+seabed9263 MACH_SEABED9263 SEABED9263 2427
+mx51_m2id MACH_MX51_M2ID MX51_M2ID 2428
+octvocplus_eb MACH_OCTVOCPLUS_EB OCTVOCPLUS_EB 2429
+klk_firefox MACH_KLK_FIREFOX KLK_FIREFOX 2430
+klk_wirma_module MACH_KLK_WIRMA_MODULE KLK_WIRMA_MODULE 2431
+klk_wirma_mmi MACH_KLK_WIRMA_MMI KLK_WIRMA_MMI 2432
+supersonic MACH_SUPERSONIC SUPERSONIC 2433
+liberty MACH_LIBERTY LIBERTY 2434
+mh355 MACH_MH355 MH355 2435
+pc7802 MACH_PC7802 PC7802 2436
+gnet_sgc MACH_GNET_SGC GNET_SGC 2437
will be called i2c-pnx.
config I2C_PXA
- tristate "Intel PXA2XX I2C adapter (EXPERIMENTAL)"
- depends on EXPERIMENTAL && ARCH_PXA
+ tristate "Intel PXA2XX I2C adapter"
+ depends on ARCH_PXA || ARCH_MMP
help
If you have devices in the PXA I2C bus, say yes to this option.
This driver can also be built as a module. If so, the module
#include <linux/clk.h>
#include <linux/scatterlist.h>
#include <linux/gpio.h>
+#include <linux/amba/mmci.h>
+#include <linux/regulator/consumer.h>
#include <asm/cacheflush.h>
#include <asm/div64.h>
#include <asm/io.h>
#include <asm/sizes.h>
-#include <asm/mach/mmc.h>
#include "mmci.h"
static unsigned int fmax = 515633;
+/*
+ * This must be called with host->lock held
+ */
+static void mmci_set_clkreg(struct mmci_host *host, unsigned int desired)
+{
+ u32 clk = 0;
+
+ if (desired) {
+ if (desired >= host->mclk) {
+ clk = MCI_CLK_BYPASS;
+ host->cclk = host->mclk;
+ } else {
+ clk = host->mclk / (2 * desired) - 1;
+ if (clk >= 256)
+ clk = 255;
+ host->cclk = host->mclk / (2 * (clk + 1));
+ }
+ if (host->hw_designer == 0x80)
+ clk |= MCI_FCEN; /* Bug fix in ST IP block */
+ clk |= MCI_CLK_ENABLE;
+ /* This hasn't proven to be worthwhile */
+ /* clk |= MCI_CLK_PWRSAVE; */
+ }
+
+ if (host->mmc->ios.bus_width == MMC_BUS_WIDTH_4)
+ clk |= MCI_WIDE_BUS;
+
+ writel(clk, host->base + MMCICLOCK);
+}
+
static void
mmci_request_end(struct mmci_host *host, struct mmc_request *mrq)
{
static void mmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
{
struct mmci_host *host = mmc_priv(mmc);
- u32 clk = 0, pwr = 0;
-
- if (ios->clock) {
- if (ios->clock >= host->mclk) {
- clk = MCI_CLK_BYPASS;
- host->cclk = host->mclk;
- } else {
- clk = host->mclk / (2 * ios->clock) - 1;
- if (clk >= 256)
- clk = 255;
- host->cclk = host->mclk / (2 * (clk + 1));
- }
- if (host->hw_designer == AMBA_VENDOR_ST)
- clk |= MCI_FCEN; /* Bug fix in ST IP block */
- clk |= MCI_CLK_ENABLE;
- }
-
- if (host->plat->translate_vdd)
- pwr |= host->plat->translate_vdd(mmc_dev(mmc), ios->vdd);
+ u32 pwr = 0;
+ unsigned long flags;
switch (ios->power_mode) {
case MMC_POWER_OFF:
+ if(host->vcc &&
+ regulator_is_enabled(host->vcc))
+ regulator_disable(host->vcc);
break;
case MMC_POWER_UP:
+#ifdef CONFIG_REGULATOR
+ if (host->vcc)
+ /* This implicitly enables the regulator */
+ mmc_regulator_set_ocr(host->vcc, ios->vdd);
+#endif
+ /*
+ * The translate_vdd function is not used if you have
+ * an external regulator, or your design is really weird.
+ * Using it would mean sending in power control BOTH using
+ * a regulator AND the 4 MMCIPWR bits. If we don't have
+ * a regulator, we might have some other platform specific
+ * power control behind this translate function.
+ */
+ if (!host->vcc && host->plat->translate_vdd)
+ pwr |= host->plat->translate_vdd(mmc_dev(mmc), ios->vdd);
/* The ST version does not have this, fall through to POWER_ON */
if (host->hw_designer != AMBA_VENDOR_ST) {
pwr |= MCI_PWR_UP;
}
}
- writel(clk, host->base + MMCICLOCK);
+ spin_lock_irqsave(&host->lock, flags);
+
+ mmci_set_clkreg(host, ios->clock);
if (host->pwr != pwr) {
host->pwr = pwr;
writel(pwr, host->base + MMCIPOWER);
}
+
+ spin_unlock_irqrestore(&host->lock, flags);
}
static int mmci_get_ro(struct mmc_host *mmc)
static int __devinit mmci_probe(struct amba_device *dev, struct amba_id *id)
{
- struct mmc_platform_data *plat = dev->dev.platform_data;
+ struct mmci_platform_data *plat = dev->dev.platform_data;
struct mmci_host *host;
struct mmc_host *mmc;
int ret;
mmc->ops = &mmci_ops;
mmc->f_min = (host->mclk + 511) / 512;
mmc->f_max = min(host->mclk, fmax);
- mmc->ocr_avail = plat->ocr_mask;
+#ifdef CONFIG_REGULATOR
+ /* If we're using the regulator framework, try to fetch a regulator */
+ host->vcc = regulator_get(&dev->dev, "vmmc");
+ if (IS_ERR(host->vcc))
+ host->vcc = NULL;
+ else {
+ int mask = mmc_regulator_get_ocrmask(host->vcc);
+
+ if (mask < 0)
+ dev_err(&dev->dev, "error getting OCR mask (%d)\n",
+ mask);
+ else {
+ host->mmc->ocr_avail = (u32) mask;
+ if (plat->ocr_mask)
+ dev_warn(&dev->dev,
+ "Provided ocr_mask/setpower will not be used "
+ "(using regulator instead)\n");
+ }
+ }
+#endif
+ /* Fall back to platform data if no regulator is found */
+ if (host->vcc == NULL)
+ mmc->ocr_avail = plat->ocr_mask;
+ mmc->caps = plat->capabilities;
/*
* We can do SGIO
clk_disable(host->clk);
clk_put(host->clk);
+ if (regulator_is_enabled(host->vcc))
+ regulator_disable(host->vcc);
+ regulator_put(host->vcc);
+
mmc_free_host(mmc);
amba_release_regions(dev);
unsigned int mclk;
unsigned int cclk;
u32 pwr;
- struct mmc_platform_data *plat;
+ struct mmci_platform_data *plat;
u8 hw_designer;
u8 hw_revision:4;
struct scatterlist *sg_ptr;
unsigned int sg_off;
unsigned int size;
+ struct regulator *vcc;
};
static inline void mmci_init_sg(struct mmci_host *host, struct mmc_data *data)
#include <linux/mmc/host.h>
#include <linux/io.h>
#include <linux/regulator/consumer.h>
+#include <linux/gpio.h>
#include <asm/sizes.h>
static inline void pxamci_set_power(struct pxamci_host *host, unsigned int vdd)
{
+ int on;
+
#ifdef CONFIG_REGULATOR
if (host->vcc)
mmc_regulator_set_ocr(host->vcc, vdd);
#endif
+ if (!host->vcc && host->pdata &&
+ gpio_is_valid(host->pdata->gpio_power)) {
+ on = ((1 << vdd) & host->pdata->ocr_mask);
+ gpio_set_value(host->pdata->gpio_power,
+ !!on ^ host->pdata->gpio_power_invert);
+ }
if (!host->vcc && host->pdata && host->pdata->setpower)
host->pdata->setpower(mmc_dev(host->mmc), vdd);
}
{
struct pxamci_host *host = mmc_priv(mmc);
+ if (host->pdata && gpio_is_valid(host->pdata->gpio_card_ro)) {
+ if (host->pdata->gpio_card_ro_invert)
+ return !gpio_get_value(host->pdata->gpio_card_ro);
+ else
+ return gpio_get_value(host->pdata->gpio_card_ro);
+ }
if (host->pdata && host->pdata->get_ro)
return !!host->pdata->get_ro(mmc_dev(mmc));
/*
struct mmc_host *mmc;
struct pxamci_host *host = NULL;
struct resource *r, *dmarx, *dmatx;
- int ret, irq;
+ int ret, irq, gpio_cd = -1, gpio_ro = -1, gpio_power = -1;
r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
irq = platform_get_irq(pdev, 0);
}
host->dma_drcmrtx = dmatx->start;
+ if (host->pdata) {
+ gpio_cd = host->pdata->gpio_card_detect;
+ gpio_ro = host->pdata->gpio_card_ro;
+ gpio_power = host->pdata->gpio_power;
+ }
+ if (gpio_is_valid(gpio_power)) {
+ ret = gpio_request(gpio_power, "mmc card power");
+ if (ret) {
+ dev_err(&pdev->dev, "Failed requesting gpio_power %d\n", gpio_power);
+ goto out;
+ }
+ gpio_direction_output(gpio_power,
+ host->pdata->gpio_power_invert);
+ }
+ if (gpio_is_valid(gpio_ro)) {
+ ret = gpio_request(gpio_ro, "mmc card read only");
+ if (ret) {
+ dev_err(&pdev->dev, "Failed requesting gpio_ro %d\n", gpio_power);
+ goto err_gpio_ro;
+ }
+ gpio_direction_input(gpio_ro);
+ }
+ if (gpio_is_valid(gpio_cd)) {
+ ret = gpio_request(gpio_cd, "mmc card detect");
+ if (ret) {
+ dev_err(&pdev->dev, "Failed requesting gpio_cd %d\n", gpio_power);
+ goto err_gpio_cd;
+ }
+ gpio_direction_input(gpio_cd);
+
+ ret = request_irq(gpio_to_irq(gpio_cd), pxamci_detect_irq,
+ IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
+ "mmc card detect", mmc);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to request card detect IRQ\n");
+ goto err_request_irq;
+ }
+ }
+
if (host->pdata && host->pdata->init)
host->pdata->init(&pdev->dev, pxamci_detect_irq, mmc);
+ if (gpio_is_valid(gpio_power) && host->pdata->setpower)
+ dev_warn(&pdev->dev, "gpio_power and setpower() both defined\n");
+ if (gpio_is_valid(gpio_ro) && host->pdata->get_ro)
+ dev_warn(&pdev->dev, "gpio_ro and get_ro() both defined\n");
+
mmc_add_host(mmc);
return 0;
+err_request_irq:
+ gpio_free(gpio_cd);
+err_gpio_cd:
+ gpio_free(gpio_ro);
+err_gpio_ro:
+ gpio_free(gpio_power);
out:
if (host) {
if (host->dma >= 0)
static int pxamci_remove(struct platform_device *pdev)
{
struct mmc_host *mmc = platform_get_drvdata(pdev);
+ int gpio_cd = -1, gpio_ro = -1, gpio_power = -1;
platform_set_drvdata(pdev, NULL);
if (mmc) {
struct pxamci_host *host = mmc_priv(mmc);
+ if (host->pdata) {
+ gpio_cd = host->pdata->gpio_card_detect;
+ gpio_ro = host->pdata->gpio_card_ro;
+ gpio_power = host->pdata->gpio_power;
+ }
+ if (gpio_is_valid(gpio_cd)) {
+ free_irq(gpio_to_irq(gpio_cd), mmc);
+ gpio_free(gpio_cd);
+ }
+ if (gpio_is_valid(gpio_ro))
+ gpio_free(gpio_ro);
+ if (gpio_is_valid(gpio_power))
+ gpio_free(gpio_power);
if (host->vcc)
regulator_put(host->vcc);
}
#ifdef CONFIG_PM
-static int pxamci_suspend(struct platform_device *dev, pm_message_t state)
+static int pxamci_suspend(struct device *dev)
{
- struct mmc_host *mmc = platform_get_drvdata(dev);
+ struct mmc_host *mmc = dev_get_drvdata(dev);
int ret = 0;
if (mmc)
- ret = mmc_suspend_host(mmc, state);
+ ret = mmc_suspend_host(mmc, PMSG_SUSPEND);
return ret;
}
-static int pxamci_resume(struct platform_device *dev)
+static int pxamci_resume(struct device *dev)
{
- struct mmc_host *mmc = platform_get_drvdata(dev);
+ struct mmc_host *mmc = dev_get_drvdata(dev);
int ret = 0;
if (mmc)
return ret;
}
-#else
-#define pxamci_suspend NULL
-#define pxamci_resume NULL
+
+static struct dev_pm_ops pxamci_pm_ops = {
+ .suspend = pxamci_suspend,
+ .resume = pxamci_resume,
+};
#endif
static struct platform_driver pxamci_driver = {
.probe = pxamci_probe,
.remove = pxamci_remove,
- .suspend = pxamci_suspend,
- .resume = pxamci_resume,
.driver = {
.name = DRIVER_NAME,
.owner = THIS_MODULE,
+#ifdef CONFIG_PM
+ .pm = &pxamci_pm_ops,
+#endif
},
};
#include <linux/etherdevice.h>
#include <linux/platform_device.h>
#include <linux/clk.h>
+#include <linux/gpio.h>
#include <net/irda/irda.h>
#include <net/irda/irmod.h>
DCSR(si->txdma) |= DCSR_RUN;
}
+/*
+ * Set the IrDA communications mode.
+ */
+static void pxa_irda_set_mode(struct pxa_irda *si, int mode)
+{
+ if (si->pdata->transceiver_mode)
+ si->pdata->transceiver_mode(si->dev, mode);
+ else {
+ if (gpio_is_valid(si->pdata->gpio_pwdown))
+ gpio_set_value(si->pdata->gpio_pwdown,
+ !(mode & IR_OFF) ^
+ !si->pdata->gpio_pwdown_inverted);
+ pxa2xx_transceiver_mode(si->dev, mode);
+ }
+}
+
/*
* Set the IrDA communications speed.
*/
pxa_irda_disable_clk(si);
/* set board transceiver to SIR mode */
- si->pdata->transceiver_mode(si->dev, IR_SIRMODE);
+ pxa_irda_set_mode(si, IR_SIRMODE);
/* enable the STUART clock */
pxa_irda_enable_sirclk(si);
ICCR0 = 0;
/* set board transceiver to FIR mode */
- si->pdata->transceiver_mode(si->dev, IR_FIRMODE);
+ pxa_irda_set_mode(si, IR_FIRMODE);
/* enable the FICP clock */
pxa_irda_enable_firclk(si);
local_irq_restore(flags);
/* power off board transceiver */
- si->pdata->transceiver_mode(si->dev, IR_OFF);
+ pxa_irda_set_mode(si, IR_OFF);
printk(KERN_DEBUG "pxa_ir: irda shutdown\n");
}
if (err)
goto err_mem_5;
- if (si->pdata->startup)
+ if (gpio_is_valid(si->pdata->gpio_pwdown)) {
+ err = gpio_request(si->pdata->gpio_pwdown, "IrDA switch");
+ if (err)
+ goto err_startup;
+ err = gpio_direction_output(si->pdata->gpio_pwdown,
+ !si->pdata->gpio_pwdown_inverted);
+ if (err) {
+ gpio_free(si->pdata->gpio_pwdown);
+ goto err_startup;
+ }
+ }
+
+ if (si->pdata->startup) {
err = si->pdata->startup(si->dev);
- if (err)
- goto err_startup;
+ if (err)
+ goto err_startup;
+ }
+
+ if (gpio_is_valid(si->pdata->gpio_pwdown) && si->pdata->startup)
+ dev_warn(si->dev, "gpio_pwdown and startup() both defined!\n");
dev->netdev_ops = &pxa_irda_netdev_ops;
if (dev) {
struct pxa_irda *si = netdev_priv(dev);
unregister_netdev(dev);
+ if (gpio_is_valid(si->pdata->gpio_pwdown))
+ gpio_free(si->pdata->gpio_pwdown);
if (si->pdata->shutdown)
si->pdata->shutdown(si->dev);
kfree(si->tx_buff.head);
pxa2xx-obj-$(CONFIG_ARCH_VIPER) += pxa2xx_viper.o
pxa2xx-obj-$(CONFIG_TRIZEPS_PCMCIA) += pxa2xx_trizeps4.o
pxa2xx-obj-$(CONFIG_MACH_PALMTX) += pxa2xx_palmtx.o
+pxa2xx-obj-$(CONFIG_MACH_PALMTC) += pxa2xx_palmtc.o
pxa2xx-obj-$(CONFIG_MACH_PALMLD) += pxa2xx_palmld.o
pxa2xx-obj-$(CONFIG_MACH_E740) += pxa2xx_e740.o
pxa2xx-obj-$(CONFIG_MACH_STARGATE2) += pxa2xx_stargate2.o
return soc_common_drv_pcmcia_remove(&dev->dev);
}
-static int pxa2xx_drv_pcmcia_suspend(struct platform_device *dev, pm_message_t state)
+static int pxa2xx_drv_pcmcia_suspend(struct device *dev)
{
- return pcmcia_socket_dev_suspend(&dev->dev, state);
+ return pcmcia_socket_dev_suspend(dev, PMSG_SUSPEND);
}
-static int pxa2xx_drv_pcmcia_resume(struct platform_device *dev)
+static int pxa2xx_drv_pcmcia_resume(struct device *dev)
{
- pxa2xx_configure_sockets(&dev->dev);
- return pcmcia_socket_dev_resume(&dev->dev);
+ pxa2xx_configure_sockets(dev);
+ return pcmcia_socket_dev_resume(dev);
}
+static struct dev_pm_ops pxa2xx_drv_pcmcia_pm_ops = {
+ .suspend = pxa2xx_drv_pcmcia_suspend,
+ .resume = pxa2xx_drv_pcmcia_resume,
+};
+
static struct platform_driver pxa2xx_pcmcia_driver = {
.probe = pxa2xx_drv_pcmcia_probe,
.remove = pxa2xx_drv_pcmcia_remove,
- .suspend = pxa2xx_drv_pcmcia_suspend,
- .resume = pxa2xx_drv_pcmcia_resume,
.driver = {
.name = "pxa2xx-pcmcia",
.owner = THIS_MODULE,
+ .pm = &pxa2xx_drv_pcmcia_pm_ops,
},
};
--- /dev/null
+/*
+ * linux/drivers/pcmcia/pxa2xx_palmtc.c
+ *
+ * Driver for Palm Tungsten|C PCMCIA
+ *
+ * Copyright (C) 2008 Alex Osborne <ato@meshy.org>
+ * Copyright (C) 2009 Marek Vasut <marek.vasut@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/gpio.h>
+#include <linux/delay.h>
+
+#include <asm/mach-types.h>
+#include <mach/palmtc.h>
+#include "soc_common.h"
+
+static int palmtc_pcmcia_hw_init(struct soc_pcmcia_socket *skt)
+{
+ int ret;
+
+ ret = gpio_request(GPIO_NR_PALMTC_PCMCIA_POWER1, "PCMCIA PWR1");
+ if (ret)
+ goto err1;
+ ret = gpio_direction_output(GPIO_NR_PALMTC_PCMCIA_POWER1, 0);
+ if (ret)
+ goto err2;
+
+ ret = gpio_request(GPIO_NR_PALMTC_PCMCIA_POWER2, "PCMCIA PWR2");
+ if (ret)
+ goto err2;
+ ret = gpio_direction_output(GPIO_NR_PALMTC_PCMCIA_POWER2, 0);
+ if (ret)
+ goto err3;
+
+ ret = gpio_request(GPIO_NR_PALMTC_PCMCIA_POWER3, "PCMCIA PWR3");
+ if (ret)
+ goto err3;
+ ret = gpio_direction_output(GPIO_NR_PALMTC_PCMCIA_POWER3, 0);
+ if (ret)
+ goto err4;
+
+ ret = gpio_request(GPIO_NR_PALMTC_PCMCIA_RESET, "PCMCIA RST");
+ if (ret)
+ goto err4;
+ ret = gpio_direction_output(GPIO_NR_PALMTC_PCMCIA_RESET, 1);
+ if (ret)
+ goto err5;
+
+ ret = gpio_request(GPIO_NR_PALMTC_PCMCIA_READY, "PCMCIA RDY");
+ if (ret)
+ goto err5;
+ ret = gpio_direction_input(GPIO_NR_PALMTC_PCMCIA_READY);
+ if (ret)
+ goto err6;
+
+ ret = gpio_request(GPIO_NR_PALMTC_PCMCIA_PWRREADY, "PCMCIA PWRRDY");
+ if (ret)
+ goto err6;
+ ret = gpio_direction_input(GPIO_NR_PALMTC_PCMCIA_PWRREADY);
+ if (ret)
+ goto err7;
+
+ skt->irq = IRQ_GPIO(GPIO_NR_PALMTC_PCMCIA_READY);
+ return 0;
+
+err7:
+ gpio_free(GPIO_NR_PALMTC_PCMCIA_PWRREADY);
+err6:
+ gpio_free(GPIO_NR_PALMTC_PCMCIA_READY);
+err5:
+ gpio_free(GPIO_NR_PALMTC_PCMCIA_RESET);
+err4:
+ gpio_free(GPIO_NR_PALMTC_PCMCIA_POWER3);
+err3:
+ gpio_free(GPIO_NR_PALMTC_PCMCIA_POWER2);
+err2:
+ gpio_free(GPIO_NR_PALMTC_PCMCIA_POWER1);
+err1:
+ return ret;
+}
+
+static void palmtc_pcmcia_hw_shutdown(struct soc_pcmcia_socket *skt)
+{
+ gpio_free(GPIO_NR_PALMTC_PCMCIA_PWRREADY);
+ gpio_free(GPIO_NR_PALMTC_PCMCIA_READY);
+ gpio_free(GPIO_NR_PALMTC_PCMCIA_RESET);
+ gpio_free(GPIO_NR_PALMTC_PCMCIA_POWER3);
+ gpio_free(GPIO_NR_PALMTC_PCMCIA_POWER2);
+ gpio_free(GPIO_NR_PALMTC_PCMCIA_POWER1);
+}
+
+static void palmtc_pcmcia_socket_state(struct soc_pcmcia_socket *skt,
+ struct pcmcia_state *state)
+{
+ state->detect = 1; /* always inserted */
+ state->ready = !!gpio_get_value(GPIO_NR_PALMTC_PCMCIA_READY);
+ state->bvd1 = 1;
+ state->bvd2 = 1;
+ state->wrprot = 0;
+ state->vs_3v = 1;
+ state->vs_Xv = 0;
+}
+
+static int palmtc_wifi_powerdown(void)
+{
+ gpio_set_value(GPIO_NR_PALMTC_PCMCIA_RESET, 1);
+ gpio_set_value(GPIO_NR_PALMTC_PCMCIA_POWER2, 0);
+ mdelay(40);
+ gpio_set_value(GPIO_NR_PALMTC_PCMCIA_POWER1, 0);
+ return 0;
+}
+
+static int palmtc_wifi_powerup(void)
+{
+ int timeout = 50;
+
+ gpio_set_value(GPIO_NR_PALMTC_PCMCIA_POWER3, 1);
+ mdelay(50);
+
+ /* Power up the card, 1.8V first, after a while 3.3V */
+ gpio_set_value(GPIO_NR_PALMTC_PCMCIA_POWER1, 1);
+ mdelay(100);
+ gpio_set_value(GPIO_NR_PALMTC_PCMCIA_POWER2, 1);
+
+ /* Wait till the card is ready */
+ while (!gpio_get_value(GPIO_NR_PALMTC_PCMCIA_PWRREADY) &&
+ timeout) {
+ mdelay(1);
+ timeout--;
+ }
+
+ /* Power down the WiFi in case of error */
+ if (!timeout) {
+ palmtc_wifi_powerdown();
+ return 1;
+ }
+
+ /* Reset the card */
+ gpio_set_value(GPIO_NR_PALMTC_PCMCIA_RESET, 1);
+ mdelay(20);
+ gpio_set_value(GPIO_NR_PALMTC_PCMCIA_RESET, 0);
+ mdelay(25);
+
+ gpio_set_value(GPIO_NR_PALMTC_PCMCIA_POWER3, 0);
+
+ return 0;
+}
+
+static int palmtc_pcmcia_configure_socket(struct soc_pcmcia_socket *skt,
+ const socket_state_t *state)
+{
+ int ret = 1;
+
+ if (state->Vcc == 0)
+ ret = palmtc_wifi_powerdown();
+ else if (state->Vcc == 33)
+ ret = palmtc_wifi_powerup();
+
+ return ret;
+}
+
+static void palmtc_pcmcia_socket_init(struct soc_pcmcia_socket *skt)
+{
+}
+
+static void palmtc_pcmcia_socket_suspend(struct soc_pcmcia_socket *skt)
+{
+}
+
+static struct pcmcia_low_level palmtc_pcmcia_ops = {
+ .owner = THIS_MODULE,
+
+ .first = 0,
+ .nr = 1,
+
+ .hw_init = palmtc_pcmcia_hw_init,
+ .hw_shutdown = palmtc_pcmcia_hw_shutdown,
+
+ .socket_state = palmtc_pcmcia_socket_state,
+ .configure_socket = palmtc_pcmcia_configure_socket,
+
+ .socket_init = palmtc_pcmcia_socket_init,
+ .socket_suspend = palmtc_pcmcia_socket_suspend,
+};
+
+static struct platform_device *palmtc_pcmcia_device;
+
+static int __init palmtc_pcmcia_init(void)
+{
+ int ret;
+
+ if (!machine_is_palmtc())
+ return -ENODEV;
+
+ palmtc_pcmcia_device = platform_device_alloc("pxa2xx-pcmcia", -1);
+ if (!palmtc_pcmcia_device)
+ return -ENOMEM;
+
+ ret = platform_device_add_data(palmtc_pcmcia_device, &palmtc_pcmcia_ops,
+ sizeof(palmtc_pcmcia_ops));
+
+ if (!ret)
+ ret = platform_device_add(palmtc_pcmcia_device);
+
+ if (ret)
+ platform_device_put(palmtc_pcmcia_device);
+
+ return ret;
+}
+
+static void __exit palmtc_pcmcia_exit(void)
+{
+ platform_device_unregister(palmtc_pcmcia_device);
+}
+
+module_init(palmtc_pcmcia_init);
+module_exit(palmtc_pcmcia_exit);
+
+MODULE_AUTHOR("Alex Osborne <ato@meshy.org>,"
+ " Marek Vasut <marek.vasut@gmail.com>");
+MODULE_DESCRIPTION("PCMCIA support for Palm Tungsten|C");
+MODULE_ALIAS("platform:pxa2xx-pcmcia");
+MODULE_LICENSE("GPL");
}
#ifdef CONFIG_PM
-static int pxa_rtc_suspend(struct platform_device *pdev, pm_message_t state)
+static int pxa_rtc_suspend(struct device *dev)
{
- struct pxa_rtc *pxa_rtc = platform_get_drvdata(pdev);
+ struct pxa_rtc *pxa_rtc = dev_get_drvdata(dev);
- if (device_may_wakeup(&pdev->dev))
+ if (device_may_wakeup(dev))
enable_irq_wake(pxa_rtc->irq_Alrm);
return 0;
}
-static int pxa_rtc_resume(struct platform_device *pdev)
+static int pxa_rtc_resume(struct device *dev)
{
- struct pxa_rtc *pxa_rtc = platform_get_drvdata(pdev);
+ struct pxa_rtc *pxa_rtc = dev_get_drvdata(dev);
- if (device_may_wakeup(&pdev->dev))
+ if (device_may_wakeup(dev))
disable_irq_wake(pxa_rtc->irq_Alrm);
return 0;
}
-#else
-#define pxa_rtc_suspend NULL
-#define pxa_rtc_resume NULL
+
+static struct dev_pm_ops pxa_rtc_pm_ops = {
+ .suspend = pxa_rtc_suspend,
+ .resume = pxa_rtc_resume,
+};
#endif
static struct platform_driver pxa_rtc_driver = {
.remove = __exit_p(pxa_rtc_remove),
- .suspend = pxa_rtc_suspend,
- .resume = pxa_rtc_resume,
.driver = {
- .name = "pxa-rtc",
+ .name = "pxa-rtc",
+#ifdef CONFIG_PM
+ .pm = &pxa_rtc_pm_ops,
+#endif
},
};
}
#ifdef CONFIG_PM
-static int sa1100_rtc_suspend(struct platform_device *pdev, pm_message_t state)
+static int sa1100_rtc_suspend(struct device *dev)
{
- if (device_may_wakeup(&pdev->dev))
+ if (device_may_wakeup(dev))
enable_irq_wake(IRQ_RTCAlrm);
return 0;
}
-static int sa1100_rtc_resume(struct platform_device *pdev)
+static int sa1100_rtc_resume(struct device *dev)
{
- if (device_may_wakeup(&pdev->dev))
+ if (device_may_wakeup(dev))
disable_irq_wake(IRQ_RTCAlrm);
return 0;
}
-#else
-#define sa1100_rtc_suspend NULL
-#define sa1100_rtc_resume NULL
+
+static struct dev_pm_ops sa1100_rtc_pm_ops = {
+ .suspend = sa1100_rtc_suspend,
+ .resume = sa1100_rtc_resume,
+};
#endif
static struct platform_driver sa1100_rtc_driver = {
.probe = sa1100_rtc_probe,
.remove = sa1100_rtc_remove,
- .suspend = sa1100_rtc_suspend,
- .resume = sa1100_rtc_resume,
.driver = {
- .name = "sa1100-rtc",
+ .name = "sa1100-rtc",
+#ifdef CONFIG_PM
+ .pm = &sa1100_rtc_pm_ops,
+#endif
},
};
.cons = PXA_CONSOLE,
};
-static int serial_pxa_suspend(struct platform_device *dev, pm_message_t state)
+#ifdef CONFIG_PM
+static int serial_pxa_suspend(struct device *dev)
{
- struct uart_pxa_port *sport = platform_get_drvdata(dev);
+ struct uart_pxa_port *sport = dev_get_drvdata(dev);
if (sport)
uart_suspend_port(&serial_pxa_reg, &sport->port);
return 0;
}
-static int serial_pxa_resume(struct platform_device *dev)
+static int serial_pxa_resume(struct device *dev)
{
- struct uart_pxa_port *sport = platform_get_drvdata(dev);
+ struct uart_pxa_port *sport = dev_get_drvdata(dev);
if (sport)
uart_resume_port(&serial_pxa_reg, &sport->port);
return 0;
}
+static struct dev_pm_ops serial_pxa_pm_ops = {
+ .suspend = serial_pxa_suspend,
+ .resume = serial_pxa_resume,
+};
+#endif
+
static int serial_pxa_probe(struct platform_device *dev)
{
struct uart_pxa_port *sport;
.probe = serial_pxa_probe,
.remove = serial_pxa_remove,
- .suspend = serial_pxa_suspend,
- .resume = serial_pxa_resume,
.driver = {
.name = "pxa2xx-uart",
.owner = THIS_MODULE,
+#ifdef CONFIG_PM
+ .pm = &serial_pxa_pm_ops,
+#endif
},
};
GEN_MASK_BITS(SSP_DATA_BITS_12, SSP_CR0_MASK_DSS, 0) | \
GEN_MASK_BITS(SSP_MICROWIRE_CHANNEL_FULL_DUPLEX, SSP_CR0_MASK_HALFDUP, 5) | \
GEN_MASK_BITS(SSP_CLK_POL_IDLE_LOW, SSP_CR0_MASK_SPO, 6) | \
- GEN_MASK_BITS(SSP_CLK_FALLING_EDGE, SSP_CR0_MASK_SPH, 7) | \
+ GEN_MASK_BITS(SSP_CLK_SECOND_EDGE, SSP_CR0_MASK_SPH, 7) | \
GEN_MASK_BITS(NMDK_SSP_DEFAULT_CLKRATE, SSP_CR0_MASK_SCR, 8) | \
GEN_MASK_BITS(SSP_BITS_8, SSP_CR0_MASK_CSS, 16) | \
GEN_MASK_BITS(SSP_INTERFACE_MOTOROLA_SPI, SSP_CR0_MASK_FRF, 21) \
return -EINVAL;
}
if (chip_info->iface == SSP_INTERFACE_MOTOROLA_SPI) {
- if ((chip_info->clk_phase != SSP_CLK_RISING_EDGE)
- && (chip_info->clk_phase != SSP_CLK_FALLING_EDGE)) {
+ if ((chip_info->clk_phase != SSP_CLK_FIRST_EDGE)
+ && (chip_info->clk_phase != SSP_CLK_SECOND_EDGE)) {
dev_err(chip_info->dev,
"Clock Phase is configured incorrectly\n");
return -EINVAL;
chip_info->data_size = SSP_DATA_BITS_12;
chip_info->rx_lev_trig = SSP_RX_1_OR_MORE_ELEM;
chip_info->tx_lev_trig = SSP_TX_1_OR_MORE_EMPTY_LOC;
- chip_info->clk_phase = SSP_CLK_FALLING_EDGE;
+ chip_info->clk_phase = SSP_CLK_SECOND_EDGE;
chip_info->clk_pol = SSP_CLK_POL_IDLE_LOW;
chip_info->ctrl_len = SSP_BITS_8;
chip_info->wait_state = SSP_MWIRE_WAIT_ZERO;
}
#ifdef CONFIG_PM
-
-static int pxa2xx_spi_suspend(struct platform_device *pdev, pm_message_t state)
+static int pxa2xx_spi_suspend(struct device *dev)
{
- struct driver_data *drv_data = platform_get_drvdata(pdev);
+ struct driver_data *drv_data = dev_get_drvdata(dev);
struct ssp_device *ssp = drv_data->ssp;
int status = 0;
return 0;
}
-static int pxa2xx_spi_resume(struct platform_device *pdev)
+static int pxa2xx_spi_resume(struct device *dev)
{
- struct driver_data *drv_data = platform_get_drvdata(pdev);
+ struct driver_data *drv_data = dev_get_drvdata(dev);
struct ssp_device *ssp = drv_data->ssp;
int status = 0;
/* Start the queue running */
status = start_queue(drv_data);
if (status != 0) {
- dev_err(&pdev->dev, "problem starting queue (%d)\n", status);
+ dev_err(dev, "problem starting queue (%d)\n", status);
return status;
}
return 0;
}
-#else
-#define pxa2xx_spi_suspend NULL
-#define pxa2xx_spi_resume NULL
-#endif /* CONFIG_PM */
+
+static struct dev_pm_ops pxa2xx_spi_pm_ops = {
+ .suspend = pxa2xx_spi_suspend,
+ .resume = pxa2xx_spi_resume,
+};
+#endif
static struct platform_driver driver = {
.driver = {
- .name = "pxa2xx-spi",
- .owner = THIS_MODULE,
+ .name = "pxa2xx-spi",
+ .owner = THIS_MODULE,
+#ifdef CONFIG_PM
+ .pm = &pxa2xx_spi_pm_ops,
+#endif
},
.remove = pxa2xx_spi_remove,
.shutdown = pxa2xx_spi_shutdown,
- .suspend = pxa2xx_spi_suspend,
- .resume = pxa2xx_spi_resume,
};
static int __init pxa2xx_spi_init(void)
return 0;
}
-#ifdef CONFIG_PM
-static int ohci_hcd_pxa27x_drv_suspend(struct platform_device *pdev, pm_message_t state)
+#ifdef CONFIG_PM
+static int ohci_hcd_pxa27x_drv_suspend(struct device *dev)
{
- struct usb_hcd *hcd = platform_get_drvdata(pdev);
+ struct usb_hcd *hcd = dev_get_drvdata(dev);
struct pxa27x_ohci *ohci = to_pxa27x_ohci(hcd);
if (time_before(jiffies, ohci->ohci.next_statechange))
msleep(5);
ohci->ohci.next_statechange = jiffies;
- pxa27x_stop_hc(ohci, &pdev->dev);
+ pxa27x_stop_hc(ohci, dev);
hcd->state = HC_STATE_SUSPENDED;
return 0;
}
-static int ohci_hcd_pxa27x_drv_resume(struct platform_device *pdev)
+static int ohci_hcd_pxa27x_drv_resume(struct device *dev)
{
- struct usb_hcd *hcd = platform_get_drvdata(pdev);
+ struct usb_hcd *hcd = dev_get_drvdata(dev);
struct pxa27x_ohci *ohci = to_pxa27x_ohci(hcd);
+ struct pxaohci_platform_data *inf = dev->platform_data;
int status;
if (time_before(jiffies, ohci->ohci.next_statechange))
msleep(5);
ohci->ohci.next_statechange = jiffies;
- if ((status = pxa27x_start_hc(ohci, &pdev->dev)) < 0)
+ if ((status = pxa27x_start_hc(ohci, dev)) < 0)
return status;
+ /* Select Power Management Mode */
+ pxa27x_ohci_select_pmm(ohci, inf->port_mode);
+
ohci_finish_controller_resume(hcd);
return 0;
}
+
+static struct dev_pm_ops ohci_hcd_pxa27x_pm_ops = {
+ .suspend = ohci_hcd_pxa27x_drv_suspend,
+ .resume = ohci_hcd_pxa27x_drv_resume,
+};
#endif
/* work with hotplug and coldplug */
.probe = ohci_hcd_pxa27x_drv_probe,
.remove = ohci_hcd_pxa27x_drv_remove,
.shutdown = usb_hcd_platform_shutdown,
-#ifdef CONFIG_PM
- .suspend = ohci_hcd_pxa27x_drv_suspend,
- .resume = ohci_hcd_pxa27x_drv_resume,
-#endif
.driver = {
.name = "pxa27x-ohci",
.owner = THIS_MODULE,
+#ifdef CONFIG_PM
+ .pm = &ohci_hcd_pxa27x_pm_ops,
+#endif
},
};
}
#ifdef CONFIG_PM
-static int da903x_backlight_suspend(struct platform_device *pdev,
- pm_message_t state)
+static int da903x_backlight_suspend(struct device *dev)
{
+ struct platform_device *pdev = to_platform_device(dev);
struct backlight_device *bl = platform_get_drvdata(pdev);
return da903x_backlight_set(bl, 0);
}
-static int da903x_backlight_resume(struct platform_device *pdev)
+static int da903x_backlight_resume(struct device *dev)
{
+ struct platform_device *pdev = to_platform_device(dev);
struct backlight_device *bl = platform_get_drvdata(pdev);
backlight_update_status(bl);
return 0;
}
-#else
-#define da903x_backlight_suspend NULL
-#define da903x_backlight_resume NULL
+
+static struct dev_pm_ops da903x_backlight_pm_ops = {
+ .suspend = da903x_backlight_suspend,
+ .resume = da903x_backlight_resume,
+};
#endif
static struct platform_driver da903x_backlight_driver = {
.driver = {
.name = "da903x-backlight",
.owner = THIS_MODULE,
+#ifdef CONFIG_PM
+ .pm = &da903x_backlight_pm_ops,
+#endif
},
.probe = da903x_backlight_probe,
.remove = da903x_backlight_remove,
- .suspend = da903x_backlight_suspend,
- .resume = da903x_backlight_resume,
};
static int __init da903x_backlight_init(void)
* Power management hooks. Note that we won't be called from IRQ context,
* unlike the blank functions above, so we may sleep.
*/
-static int pxafb_suspend(struct platform_device *dev, pm_message_t state)
+static int pxafb_suspend(struct device *dev)
{
- struct pxafb_info *fbi = platform_get_drvdata(dev);
+ struct pxafb_info *fbi = dev_get_drvdata(dev);
set_ctrlr_state(fbi, C_DISABLE_PM);
return 0;
}
-static int pxafb_resume(struct platform_device *dev)
+static int pxafb_resume(struct device *dev)
{
- struct pxafb_info *fbi = platform_get_drvdata(dev);
+ struct pxafb_info *fbi = dev_get_drvdata(dev);
set_ctrlr_state(fbi, C_ENABLE_PM);
return 0;
}
-#else
-#define pxafb_suspend NULL
-#define pxafb_resume NULL
+
+static struct dev_pm_ops pxafb_pm_ops = {
+ .suspend = pxafb_suspend,
+ .resume = pxafb_resume,
+};
#endif
static int __devinit pxafb_init_video_memory(struct pxafb_info *fbi)
goto failed;
}
+ if (cpu_is_pxa3xx() && inf->acceleration_enabled)
+ fbi->fb.fix.accel = FB_ACCEL_PXA3XX;
+
fbi->backlight_power = inf->pxafb_backlight_power;
fbi->lcd_power = inf->pxafb_lcd_power;
goto failed_fbi;
}
- r = request_mem_region(r->start, r->end - r->start + 1, dev->name);
+ r = request_mem_region(r->start, resource_size(r), dev->name);
if (r == NULL) {
dev_err(&dev->dev, "failed to request I/O memory\n");
ret = -EBUSY;
goto failed_fbi;
}
- fbi->mmio_base = ioremap(r->start, r->end - r->start + 1);
+ fbi->mmio_base = ioremap(r->start, resource_size(r));
if (fbi->mmio_base == NULL) {
dev_err(&dev->dev, "failed to map I/O memory\n");
ret = -EBUSY;
failed_free_io:
iounmap(fbi->mmio_base);
failed_free_res:
- release_mem_region(r->start, r->end - r->start + 1);
+ release_mem_region(r->start, resource_size(r));
failed_fbi:
clk_put(fbi->clk);
platform_set_drvdata(dev, NULL);
iounmap(fbi->mmio_base);
r = platform_get_resource(dev, IORESOURCE_MEM, 0);
- release_mem_region(r->start, r->end - r->start + 1);
+ release_mem_region(r->start, resource_size(r));
clk_put(fbi->clk);
kfree(fbi);
static struct platform_driver pxafb_driver = {
.probe = pxafb_probe,
.remove = __devexit_p(pxafb_remove),
- .suspend = pxafb_suspend,
- .resume = pxafb_resume,
.driver = {
.owner = THIS_MODULE,
.name = "pxa2xx-fb",
+#ifdef CONFIG_PM
+ .pm = &pxafb_pm_ops,
+#endif
},
};
/*
- * arch/arm/include/asm/mach/mmc.h
+ * include/linux/amba/mmci.h
*/
-#ifndef ASMARM_MACH_MMC_H
-#define ASMARM_MACH_MMC_H
+#ifndef AMBA_MMCI_H
+#define AMBA_MMCI_H
#include <linux/mmc/host.h>
-struct mmc_platform_data {
+struct mmci_platform_data {
unsigned int ocr_mask; /* available voltages */
u32 (*translate_vdd)(struct device *, unsigned int);
unsigned int (*status)(struct device *);
int gpio_wp;
int gpio_cd;
+ unsigned long capabilities;
};
#endif
/**
* enum SPI Clock Phase - clock phase (Motorola SPI interface only)
- * @SSP_CLK_RISING_EDGE: Receive data on rising edge
- * @SSP_CLK_FALLING_EDGE: Receive data on falling edge
+ * @SSP_CLK_FIRST_EDGE: Receive data on first edge transition (actual direction depends on polarity)
+ * @SSP_CLK_SECOND_EDGE: Receive data on second edge transition (actual direction depends on polarity)
*/
enum ssp_spi_clk_phase {
- SSP_CLK_RISING_EDGE,
- SSP_CLK_FALLING_EDGE
+ SSP_CLK_FIRST_EDGE,
+ SSP_CLK_SECOND_EDGE
};
/**
#define FB_ACCEL_NEOMAGIC_NM2230 96 /* NeoMagic NM2230 */
#define FB_ACCEL_NEOMAGIC_NM2360 97 /* NeoMagic NM2360 */
#define FB_ACCEL_NEOMAGIC_NM2380 98 /* NeoMagic NM2380 */
+#define FB_ACCEL_PXA3XX 99 /* PXA3xx */
#define FB_ACCEL_SAVAGE4 0x80 /* S3 Savage4 */
#define FB_ACCEL_SAVAGE3D 0x81 /* S3 Savage3D */
return 0;
}
-static int pxa2xx_ac97_suspend(struct platform_device *dev, pm_message_t state)
+static int pxa2xx_ac97_suspend(struct device *dev)
{
- struct snd_card *card = platform_get_drvdata(dev);
+ struct snd_card *card = dev_get_drvdata(dev);
int ret = 0;
if (card)
return ret;
}
-static int pxa2xx_ac97_resume(struct platform_device *dev)
+static int pxa2xx_ac97_resume(struct device *dev)
{
- struct snd_card *card = platform_get_drvdata(dev);
+ struct snd_card *card = dev_get_drvdata(dev);
int ret = 0;
if (card)
return ret;
}
-#else
-#define pxa2xx_ac97_suspend NULL
-#define pxa2xx_ac97_resume NULL
+static struct dev_pm_ops pxa2xx_ac97_pm_ops = {
+ .suspend = pxa2xx_ac97_suspend,
+ .resume = pxa2xx_ac97_resume,
+};
#endif
static int __devinit pxa2xx_ac97_probe(struct platform_device *dev)
static struct platform_driver pxa2xx_ac97_driver = {
.probe = pxa2xx_ac97_probe,
.remove = __devexit_p(pxa2xx_ac97_remove),
- .suspend = pxa2xx_ac97_suspend,
- .resume = pxa2xx_ac97_resume,
.driver = {
.name = "pxa2xx-ac97",
.owner = THIS_MODULE,
+#ifdef CONFIG_PM
+ .pm = &pxa2xx_ac97_pm_ops,
+#endif
},
};
projects / ~andy / linux / commitdiff