- compatible : Should be "fsl,<chip>-esdhc"
Optional properties:
-- fsl,cd-internal : Indicate to use controller internal card detection
-- fsl,wp-internal : Indicate to use controller internal write protection
+- fsl,cd-controller : Indicate to use controller internal card detection
+- fsl,wp-controller : Indicate to use controller internal write protection
Examples:
compatible = "fsl,imx51-esdhc";
reg = <0x70004000 0x4000>;
interrupts = <1>;
- fsl,cd-internal;
- fsl,wp-internal;
+ fsl,cd-controller;
+ fsl,wp-controller;
};
esdhc@70008000 {
config CPU_FREQ_IMX
tristate "CPUfreq driver for i.MX CPUs"
depends on ARCH_MXC && CPU_FREQ
+ select CPU_FREQ_TABLE
help
This enables the CPUfreq driver for i.MX CPUs.
#size-cells = <0>;
ti,hwmods = "i2c3";
};
+
+ wdt2: wdt@44e35000 {
+ compatible = "ti,omap3-wdt";
+ ti,hwmods = "wd_timer2";
+ };
};
};
aips@70000000 { /* aips-1 */
spba@70000000 {
esdhc@70004000 { /* ESDHC1 */
- fsl,cd-internal;
- fsl,wp-internal;
+ fsl,cd-controller;
+ fsl,wp-controller;
status = "okay";
};
};
power-blue {
label = "power:blue";
- gpios = <&gpio1 11 0>;
+ gpios = <&gpio1 10 0>;
linux,default-trigger = "timer";
};
+ power-red {
+ label = "power:red";
+ gpios = <&gpio1 11 0>;
+ };
usb1 {
label = "usb1:blue";
gpios = <&gpio1 12 0>;
vcxio: regulator@8 {
compatible = "ti,twl6030-vcxio";
+ regulator-always-on;
};
vusb: regulator@9 {
v1v8: regulator@10 {
compatible = "ti,twl6030-v1v8";
+ regulator-always-on;
};
v2v1: regulator@11 {
compatible = "ti,twl6030-v2v1";
+ regulator-always-on;
};
clk32kg: regulator@12 {
CONFIG_LEDS_CLASS=y
CONFIG_LEDS_LM3530=y
CONFIG_LEDS_LP5521=y
+CONFIG_LEDS_GPIO=y
CONFIG_RTC_CLASS=y
CONFIG_RTC_DRV_AB8500=y
CONFIG_RTC_DRV_PL031=y
void __init dove_ge00_init(struct mv643xx_eth_platform_data *eth_data)
{
orion_ge00_init(eth_data, DOVE_GE00_PHYS_BASE,
- IRQ_DOVE_GE00_SUM, IRQ_DOVE_GE00_ERR);
+ IRQ_DOVE_GE00_SUM, IRQ_DOVE_GE00_ERR,
+ 1600);
}
/*****************************************************************************
#include <plat/backlight.h>
#include <plat/fb.h>
#include <plat/mfc.h>
+#include <plat/hdmi.h>
#include <mach/ohci.h>
#include <mach/map.h>
s3c_gpio_setpull(EXYNOS4_GPX2(2), S3C_GPIO_PULL_NONE);
}
+/* I2C module and id for HDMIPHY */
+static struct i2c_board_info hdmiphy_info = {
+ I2C_BOARD_INFO("hdmiphy-exynos4210", 0x38),
+};
+
static void s5p_tv_setup(void)
{
/* Direct HPD to HDMI chip */
s5p_tv_setup();
s5p_i2c_hdmiphy_set_platdata(NULL);
+ s5p_hdmi_set_platdata(&hdmiphy_info, NULL, 0);
#ifdef CONFIG_DRM_EXYNOS
s5p_device_fimd0.dev.platform_data = &drm_fimd_pdata;
#include <plat/mfc.h>
#include <plat/ehci.h>
#include <plat/clock.h>
+#include <plat/hdmi.h>
#include <mach/map.h>
#include <mach/ohci.h>
.pwm_period_ns = 1000,
};
+/* I2C module and id for HDMIPHY */
+static struct i2c_board_info hdmiphy_info = {
+ I2C_BOARD_INFO("hdmiphy-exynos4210", 0x38),
+};
+
static void s5p_tv_setup(void)
{
/* direct HPD to HDMI chip */
s5p_tv_setup();
s5p_i2c_hdmiphy_set_platdata(NULL);
+ s5p_hdmi_set_platdata(&hdmiphy_info, NULL, 0);
samsung_keypad_set_platdata(&smdkv310_keypad_data);
obj-$(CONFIG_SOC_IMX31) += mm-imx3.o cpu-imx31.o clk-imx31.o iomux-imx31.o ehci-imx31.o pm-imx3.o
obj-$(CONFIG_SOC_IMX35) += mm-imx3.o cpu-imx35.o clk-imx35.o ehci-imx35.o pm-imx3.o
-obj-$(CONFIG_SOC_IMX5) += cpu-imx5.o mm-imx5.o clk-imx51-imx53.o ehci-imx5.o pm-imx5.o cpu_op-mx51.o
+imx5-pm-$(CONFIG_PM) += pm-imx5.o
+obj-$(CONFIG_SOC_IMX5) += cpu-imx5.o mm-imx5.o clk-imx51-imx53.o ehci-imx5.o $(imx5-pm-y) cpu_op-mx51.o
obj-$(CONFIG_COMMON_CLK) += clk-pllv1.o clk-pllv2.o clk-pllv3.o clk-gate2.o \
clk-pfd.o clk-busy.o
obj-$(CONFIG_HAVE_IMX_GPC) += gpc.o
obj-$(CONFIG_HAVE_IMX_MMDC) += mmdc.o
obj-$(CONFIG_HAVE_IMX_SRC) += src.o
-obj-$(CONFIG_CPU_V7) += head-v7.o
-AFLAGS_head-v7.o :=-Wa,-march=armv7-a
-obj-$(CONFIG_SMP) += platsmp.o
+AFLAGS_headsmp.o :=-Wa,-march=armv7-a
+obj-$(CONFIG_SMP) += headsmp.o platsmp.o
obj-$(CONFIG_HOTPLUG_CPU) += hotplug.o
obj-$(CONFIG_SOC_IMX6Q) += clk-imx6q.o mach-imx6q.o
ifeq ($(CONFIG_PM),y)
-obj-$(CONFIG_SOC_IMX6Q) += pm-imx6q.o
+obj-$(CONFIG_SOC_IMX6Q) += pm-imx6q.o headsmp.o
endif
# i.MX5 based machines
ssi2, ssi3, uart_ipg, uart_serial, usboh3, usdhc1, usdhc2, usdhc3,
usdhc4, vdo_axi, vpu_axi, cko1, pll1_sys, pll2_bus, pll3_usb_otg,
pll4_audio, pll5_video, pll6_mlb, pll7_usb_host, pll8_enet, ssi1_ipg,
- ssi2_ipg, ssi3_ipg, rom, usbphy1, usbphy2,
+ ssi2_ipg, ssi3_ipg, rom, usbphy1, usbphy2, ldb_di0_div_3_5, ldb_di1_div_3_5,
clk_max
};
clk[gpu3d_shader] = imx_clk_divider("gpu3d_shader", "gpu3d_shader_sel", base + 0x18, 29, 3);
clk[ipu1_podf] = imx_clk_divider("ipu1_podf", "ipu1_sel", base + 0x3c, 11, 3);
clk[ipu2_podf] = imx_clk_divider("ipu2_podf", "ipu2_sel", base + 0x3c, 16, 3);
- clk[ldb_di0_podf] = imx_clk_divider("ldb_di0_podf", "ldb_di0_sel", base + 0x20, 10, 1);
- clk[ldb_di1_podf] = imx_clk_divider("ldb_di1_podf", "ldb_di1_sel", base + 0x20, 11, 1);
+ clk[ldb_di0_div_3_5] = imx_clk_fixed_factor("ldb_di0_div_3_5", "ldb_di0_sel", 2, 7);
+ clk[ldb_di0_podf] = imx_clk_divider("ldb_di0_podf", "ldb_di0_div_3_5", base + 0x20, 10, 1);
+ clk[ldb_di1_div_3_5] = imx_clk_fixed_factor("ldb_di1_div_3_5", "ldb_di1_sel", 2, 7);
+ clk[ldb_di1_podf] = imx_clk_divider("ldb_di1_podf", "ldb_di1_div_3_5", base + 0x20, 11, 1);
clk[ipu1_di0_pre] = imx_clk_divider("ipu1_di0_pre", "ipu1_di0_pre_sel", base + 0x34, 3, 3);
clk[ipu1_di1_pre] = imx_clk_divider("ipu1_di1_pre", "ipu1_di1_pre_sel", base + 0x34, 12, 3);
clk[ipu2_di0_pre] = imx_clk_divider("ipu2_di0_pre", "ipu2_di0_pre_sel", base + 0x38, 3, 3);
: "cc");
}
-static inline void cpu_leave_lowpower(void)
-{
- unsigned int v;
-
- asm volatile(
- "mrc p15, 0, %0, c1, c0, 0\n"
- " orr %0, %0, %1\n"
- " mcr p15, 0, %0, c1, c0, 0\n"
- " mrc p15, 0, %0, c1, c0, 1\n"
- " orr %0, %0, %2\n"
- " mcr p15, 0, %0, c1, c0, 1\n"
- : "=&r" (v)
- : "Ir" (CR_C), "Ir" (0x40)
- : "cc");
-}
-
/*
* platform-specific code to shutdown a CPU
*
{
cpu_enter_lowpower();
imx_enable_cpu(cpu, false);
- cpu_do_idle();
- cpu_leave_lowpower();
- /* We should never return from idle */
- panic("cpu %d unexpectedly exit from shutdown\n", cpu);
+ /* spin here until hardware takes it down */
+ while (1)
+ ;
}
int platform_cpu_disable(unsigned int cpu)
/* For imx6q sabrelite board: set KSZ9021RN RGMII pad skew */
static int ksz9021rn_phy_fixup(struct phy_device *phydev)
{
- if (IS_ENABLED(CONFIG_PHYLIB)) {
+ if (IS_BUILTIN(CONFIG_PHYLIB)) {
/* min rx data delay */
phy_write(phydev, 0x0b, 0x8105);
phy_write(phydev, 0x0c, 0x0000);
static void __init imx6q_sabrelite_init(void)
{
- if (IS_ENABLED(CONFIG_PHYLIB))
+ if (IS_BUILTIN(CONFIG_PHYLIB))
phy_register_fixup_for_uid(PHY_ID_KSZ9021, MICREL_PHY_ID_MASK,
ksz9021rn_phy_fixup);
imx6q_sabrelite_cko1_setup();
dtb-$(CONFIG_MACH_DLINK_KIRKWOOD_DT) += kirkwood-dns325.dtb
dtb-$(CONFIG_MACH_ICONNECT_DT) += kirkwood-iconnect.dtb
dtb-$(CONFIG_MACH_IB62X0_DT) += kirkwood-ib62x0.dtb
-dtb-$(CONFIG_MACH_TS219_DT) += kirkwood-qnap-ts219.dtb
+dtb-$(CONFIG_MACH_TS219_DT) += kirkwood-ts219-6281.dtb
+dtb-$(CONFIG_MACH_TS219_DT) += kirkwood-ts219-6282.dtb
dtb-$(CONFIG_MACH_GOFLEXNET_DT) += kirkwood-goflexnet.dtb
dtb-$(CONFIG_MACH_LSXL_DT) += kirkwood-lschlv2.dtb
dtb-$(CONFIG_MACH_LSXL_DT) += kirkwood-lsxhl.dtb
{
orion_ge00_init(eth_data,
GE00_PHYS_BASE, IRQ_KIRKWOOD_GE00_SUM,
- IRQ_KIRKWOOD_GE00_ERR);
+ IRQ_KIRKWOOD_GE00_ERR, 1600);
/* The interface forgets the MAC address assigned by u-boot if
the clock is turned off, so claim the clk now. */
clk_prepare_enable(ge0);
{
orion_ge01_init(eth_data,
GE01_PHYS_BASE, IRQ_KIRKWOOD_GE01_SUM,
- IRQ_KIRKWOOD_GE01_ERR);
+ IRQ_KIRKWOOD_GE01_ERR, 1600);
clk_prepare_enable(ge1);
}
struct resource *res;
int ret = 0;
- if (!pdata && !pdata->pool_name)
+ if (!pdata || !pdata->pool_name)
return -ENODEV;
info = kzalloc(sizeof(*info), GFP_KERNEL);
#define WIN0_OFF(n) (BRIDGE_VIRT_BASE + 0x0000 + ((n) << 4))
#define WIN8_OFF(n) (BRIDGE_VIRT_BASE + 0x0900 + (((n) - 8) << 4))
-static void __init __iomem *win_cfg_base(int win)
+static void __init __iomem *win_cfg_base(const struct orion_addr_map_cfg *cfg, int win)
{
/*
* Find the control register base address for this window.
{
orion_ge00_init(eth_data,
GE00_PHYS_BASE, IRQ_MV78XX0_GE00_SUM,
- IRQ_MV78XX0_GE_ERR);
+ IRQ_MV78XX0_GE_ERR,
+ MV643XX_TX_CSUM_DEFAULT_LIMIT);
}
{
orion_ge01_init(eth_data,
GE01_PHYS_BASE, IRQ_MV78XX0_GE01_SUM,
- NO_IRQ);
+ NO_IRQ,
+ MV643XX_TX_CSUM_DEFAULT_LIMIT);
}
select PM_OPP if PM
select USB_ARCH_HAS_EHCI if USB_SUPPORT
select ARM_CPU_SUSPEND if PM
- select ARCH_NEEDS_CPU_IDLE_COUPLED
+ select ARCH_NEEDS_CPU_IDLE_COUPLED if SMP
config SOC_OMAP5
bool "TI OMAP5"
select CPU_V7
select ARM_GIC
select HAVE_SMP
+ select ARM_CPU_SUSPEND if PM
comment "OMAP Core Type"
depends on ARCH_OMAP2
#ifdef CONFIG_OMAP_MUX
static struct omap_board_mux board_mux[] __initdata = {
+ /* SMSC9221 LAN Controller ETH IRQ (GPIO_176) */
+ OMAP3_MUX(MCSPI1_CS2, OMAP_MUX_MODE4 | OMAP_PIN_INPUT),
{ .reg_offset = OMAP_MUX_TERMINATOR },
};
#endif
#include "hsmmc.h"
#include "common-board-devices.h"
+#define OMAP3_EVM_TS_GPIO 175
#define OMAP3_EVM_EHCI_VBUS 22
#define OMAP3_EVM_EHCI_SELECT 61
.turbo_mode = 0,
};
-/*
- * ADS7846 driver maybe request a gpio according to the value
- * of pdata->get_pendown_state, but we have done this. So set
- * get_pendown_state to avoid twice gpio requesting.
- */
-static int omap3_get_pendown_state(void)
-{
- return !gpio_get_value(OMAP3_EVM_TS_GPIO);
-}
-
static struct ads7846_platform_data ads7846_config = {
.x_max = 0x0fff,
.y_max = 0x0fff,
.debounce_rep = 1,
.gpio_pendown = -EINVAL,
.keep_vref_on = 1,
- .get_pendown_state = &omap3_get_pendown_state,
};
static struct spi_board_info ads7846_spi_board_info __initdata = {
#include "twl-common.h"
#define NAND_BLOCK_SIZE SZ_128K
-#define OMAP3_EVM_TS_GPIO 175
struct mtd_partition;
struct ads7846_platform_data;
for_each_cpu(cpu_id, cpu_online_mask) {
dev = &per_cpu(omap4_idle_dev, cpu_id);
dev->cpu = cpu_id;
+#ifdef CONFIG_ARCH_NEEDS_CPU_IDLE_COUPLED
dev->coupled_cpus = *cpu_online_mask;
-
+#endif
cpuidle_register_driver(&omap4_idle_driver);
if (cpuidle_register_device(dev)) {
* @gpio: GPIO number
* @muxnames: available signal modes for a ball
* @balls: available balls on the package
- * @partition: mux partition
*/
struct omap_mux {
u16 reg_offset;
{
int r = -ENODEV;
- if (!cpu_is_omap44xx())
+ if (!cpu_is_omap443x())
return r;
r = omap_init_opp_table(omap44xx_opp_def_list,
per_next_state = pwrdm_read_next_pwrst(per_pwrdm);
core_next_state = pwrdm_read_next_pwrst(core_pwrdm);
- if (mpu_next_state < PWRDM_POWER_ON) {
- pwrdm_pre_transition(mpu_pwrdm);
- pwrdm_pre_transition(neon_pwrdm);
- }
+ pwrdm_pre_transition(NULL);
/* PER */
if (per_next_state < PWRDM_POWER_ON) {
- pwrdm_pre_transition(per_pwrdm);
per_going_off = (per_next_state == PWRDM_POWER_OFF) ? 1 : 0;
omap2_gpio_prepare_for_idle(per_going_off);
}
/* CORE */
if (core_next_state < PWRDM_POWER_ON) {
- pwrdm_pre_transition(core_pwrdm);
if (core_next_state == PWRDM_POWER_OFF) {
omap3_core_save_context();
omap3_cm_save_context();
omap2_prm_clear_mod_reg_bits(OMAP3430_AUTO_OFF_MASK,
OMAP3430_GR_MOD,
OMAP3_PRM_VOLTCTRL_OFFSET);
- pwrdm_post_transition(core_pwrdm);
}
omap3_intc_resume_idle();
+ pwrdm_post_transition(NULL);
+
/* PER */
- if (per_next_state < PWRDM_POWER_ON) {
+ if (per_next_state < PWRDM_POWER_ON)
omap2_gpio_resume_after_idle();
- pwrdm_post_transition(per_pwrdm);
- }
-
- if (mpu_next_state < PWRDM_POWER_ON) {
- pwrdm_post_transition(mpu_pwrdm);
- pwrdm_post_transition(neon_pwrdm);
- }
}
static void omap3_pm_idle(void)
* The restore function pointer is stored at CPUx_WAKEUP_NS_PA_ADDR_OFFSET.
* It returns to the caller for CPU INACTIVE and ON power states or in case
* CPU failed to transition to targeted OFF/DORMANT state.
+ *
+ * omap4_finish_suspend() calls v7_flush_dcache_all() which doesn't save
+ * stack frame and it expects the caller to take care of it. Hence the entire
+ * stack frame is saved to avoid possible stack corruption.
*/
ENTRY(omap4_finish_suspend)
- stmfd sp!, {lr}
+ stmfd sp!, {r4-r12, lr}
cmp r0, #0x0
beq do_WFI @ No lowpower state, jump to WFI
skip_scu_gp_clear:
isb
dsb
- ldmfd sp!, {pc}
+ ldmfd sp!, {r4-r12, pc}
ENDPROC(omap4_finish_suspend)
/*
const char *pmic_type, int pmic_irq,
struct twl4030_platform_data *pmic_data)
{
+ omap_mux_init_signal("sys_nirq", OMAP_PIN_INPUT_PULLUP | OMAP_PIN_OFF_WAKEUPENABLE);
strncpy(pmic_i2c_board_info.type, pmic_type,
sizeof(pmic_i2c_board_info.type));
pmic_i2c_board_info.irq = pmic_irq;
{
orion_ge00_init(eth_data,
ORION5X_ETH_PHYS_BASE, IRQ_ORION5X_ETH_SUM,
- IRQ_ORION5X_ETH_ERR);
+ IRQ_ORION5X_ETH_ERR,
+ MV643XX_TX_CSUM_DEFAULT_LIMIT);
}
*/
enum dma_ch {
- DMACH_XD0,
+ DMACH_DT_PROP = -1, /* not yet supported, do not use */
+ DMACH_XD0 = 0,
DMACH_XD1,
DMACH_SDI,
DMACH_SPI0,
config MACH_SNOWBALL
bool "U8500 Snowball platform"
select MACH_MOP500
- select LEDS_GPIO
help
Include support for the snowball development platform.
return pdev;
}
-/* Platform device for ASoC U8500 machine */
-static struct platform_device snd_soc_u8500 = {
- .name = "snd-soc-u8500",
+/* Platform device for ASoC MOP500 machine */
+static struct platform_device snd_soc_mop500 = {
+ .name = "snd-soc-mop500",
.id = 0,
.dev = {
.platform_data = NULL,
{
struct platform_device *msp1;
- pr_info("%s: Register platform-device 'snd-soc-u8500'.\n", __func__);
- platform_device_register(&snd_soc_u8500);
+ pr_info("%s: Register platform-device 'snd-soc-mop500'.\n", __func__);
+ platform_device_register(&snd_soc_mop500);
pr_info("Initialize MSP I2S-devices.\n");
db8500_add_msp_i2s(parent, 0, U8500_MSP0_BASE, IRQ_DB8500_MSP0,
ARRAY_SIZE(mop500_platform_devs));
mop500_sdi_init(parent);
+ mop500_msp_init(parent);
i2c0_devs = ARRAY_SIZE(mop500_i2c0_devices);
i2c_register_board_info(0, mop500_i2c0_devices, i2c0_devs);
i2c_register_board_info(2, mop500_i2c2_devices,
mop500_uib_init();
+ } else if (of_machine_is_compatible("calaosystems,snowball-a9500")) {
+ mop500_msp_init(parent);
} else if (of_machine_is_compatible("st-ericsson,hrefv60+")) {
/*
* The HREFv60 board removed a GPIO expander and routed
ARRAY_SIZE(mop500_platform_devs));
hrefv60_sdi_init(parent);
+ mop500_msp_init(parent);
i2c0_devs = ARRAY_SIZE(mop500_i2c0_devices);
i2c0_devs -= NUM_PRE_V60_I2C0_DEVICES;
timer->reserved = 1;
break;
}
+ spin_unlock_irqrestore(&dm_timer_lock, flags);
if (timer) {
ret = omap_dm_timer_prepare(timer);
timer = NULL;
}
}
- spin_unlock_irqrestore(&dm_timer_lock, flags);
if (!timer)
pr_debug("%s: timer request failed!\n", __func__);
break;
}
}
+ spin_unlock_irqrestore(&dm_timer_lock, flags);
if (timer) {
ret = omap_dm_timer_prepare(timer);
timer = NULL;
}
}
- spin_unlock_irqrestore(&dm_timer_lock, flags);
if (!timer)
pr_debug("%s: timer%d request failed!\n", __func__, id);
void omap_dm_timer_disable(struct omap_dm_timer *timer)
{
- pm_runtime_put(&timer->pdev->dev);
+ pm_runtime_put_sync(&timer->pdev->dev);
}
EXPORT_SYMBOL_GPL(omap_dm_timer_disable);
#define cpu_class_is_omap1() (cpu_is_omap7xx() || cpu_is_omap15xx() || \
cpu_is_omap16xx())
#define cpu_class_is_omap2() (cpu_is_omap24xx() || cpu_is_omap34xx() || \
- cpu_is_omap44xx() || soc_is_omap54xx())
+ cpu_is_omap44xx() || soc_is_omap54xx() || \
+ soc_is_am33xx())
/* Various silicon revisions for omap2 */
#define OMAP242X_CLASS 0x24200024
# endif
#endif
+#ifdef CONFIG_SOC_AM33XX
+# ifdef OMAP_NAME
+# undef MULTI_OMAP2
+# define MULTI_OMAP2
+# else
+# define OMAP_NAME am33xx
+# endif
+#endif
+
#endif /* __PLAT_OMAP_MULTI_H */
_DEBUG_LL_ENTRY(mach, AM33XX_UART##p##_BASE, OMAP_PORT_SHIFT, \
AM33XXUART##p)
-static inline void __arch_decomp_setup(unsigned long arch_id)
+static inline void arch_decomp_setup(void)
{
int port = 0;
} while (0);
}
-#define arch_decomp_setup() __arch_decomp_setup(arch_id)
-
/*
* nothing to do
*/
void __init orion_ge00_init(struct mv643xx_eth_platform_data *eth_data,
unsigned long mapbase,
unsigned long irq,
- unsigned long irq_err)
+ unsigned long irq_err,
+ unsigned int tx_csum_limit)
{
fill_resources(&orion_ge00_shared, orion_ge00_shared_resources,
mapbase + 0x2000, SZ_16K - 1, irq_err);
+ orion_ge00_shared_data.tx_csum_limit = tx_csum_limit;
ge_complete(&orion_ge00_shared_data,
orion_ge00_resources, irq, &orion_ge00_shared,
eth_data, &orion_ge00);
void __init orion_ge01_init(struct mv643xx_eth_platform_data *eth_data,
unsigned long mapbase,
unsigned long irq,
- unsigned long irq_err)
+ unsigned long irq_err,
+ unsigned int tx_csum_limit)
{
fill_resources(&orion_ge01_shared, orion_ge01_shared_resources,
mapbase + 0x2000, SZ_16K - 1, irq_err);
+ orion_ge01_shared_data.tx_csum_limit = tx_csum_limit;
ge_complete(&orion_ge01_shared_data,
orion_ge01_resources, irq, &orion_ge01_shared,
eth_data, &orion_ge01);
void __init orion_ge00_init(struct mv643xx_eth_platform_data *eth_data,
unsigned long mapbase,
unsigned long irq,
- unsigned long irq_err);
+ unsigned long irq_err,
+ unsigned int tx_csum_limit);
void __init orion_ge01_init(struct mv643xx_eth_platform_data *eth_data,
unsigned long mapbase,
unsigned long irq,
- unsigned long irq_err);
+ unsigned long irq_err,
+ unsigned int tx_csum_limit);
void __init orion_ge10_init(struct mv643xx_eth_platform_data *eth_data,
unsigned long mapbase,
* when necessary.
*/
-int s3c2410_dma_enqueue(unsigned int channel, void *id,
+int s3c2410_dma_enqueue(enum dma_ch channel, void *id,
dma_addr_t data, int size)
{
struct s3c2410_dma_chan *chan = s3c_dma_lookup_channel(channel);
#include <linux/platform_data/s3c-hsudc.h>
#include <linux/platform_data/s3c-hsotg.h>
+#include <media/s5p_hdmi.h>
+
#include <asm/irq.h>
#include <asm/pmu.h>
#include <asm/mach/arch.h>
if (!pd) {
pd = &default_i2c_data;
- if (soc_is_exynos4210())
+ if (soc_is_exynos4210() ||
+ soc_is_exynos4212() || soc_is_exynos4412())
pd->bus_num = 8;
else if (soc_is_s5pv210())
pd->bus_num = 3;
npd = s3c_set_platdata(pd, sizeof(struct s3c2410_platform_i2c),
&s5p_device_i2c_hdmiphy);
}
+
+struct s5p_hdmi_platform_data s5p_hdmi_def_platdata;
+
+void __init s5p_hdmi_set_platdata(struct i2c_board_info *hdmiphy_info,
+ struct i2c_board_info *mhl_info, int mhl_bus)
+{
+ struct s5p_hdmi_platform_data *pd = &s5p_hdmi_def_platdata;
+
+ if (soc_is_exynos4210() ||
+ soc_is_exynos4212() || soc_is_exynos4412())
+ pd->hdmiphy_bus = 8;
+ else if (soc_is_s5pv210())
+ pd->hdmiphy_bus = 3;
+ else
+ pd->hdmiphy_bus = 0;
+
+ pd->hdmiphy_info = hdmiphy_info;
+ pd->mhl_info = mhl_info;
+ pd->mhl_bus = mhl_bus;
+
+ s3c_set_platdata(pd, sizeof(struct s5p_hdmi_platform_data),
+ &s5p_device_hdmi);
+}
+
#endif /* CONFIG_S5P_DEV_I2C_HDMIPHY */
/* I2S */
--- /dev/null
+/*
+ * Copyright (C) 2012 Samsung Electronics Co.Ltd
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#ifndef __PLAT_SAMSUNG_HDMI_H
+#define __PLAT_SAMSUNG_HDMI_H __FILE__
+
+extern void s5p_hdmi_set_platdata(struct i2c_board_info *hdmiphy_info,
+ struct i2c_board_info *mhl_info, int mhl_bus);
+
+#endif /* __PLAT_SAMSUNG_HDMI_H */
#ifdef CONFIG_SAMSUNG_PM_DEBUG
-struct pm_uart_save uart_save[CONFIG_SERIAL_SAMSUNG_UARTS];
+static struct pm_uart_save uart_save[CONFIG_SERIAL_SAMSUNG_UARTS];
static void s3c_pm_save_uart(unsigned int uart, struct pm_uart_save *save)
{
policy->cur = policy->min = policy->max = omap_getspeed(policy->cpu);
- if (atomic_inc_return(&freq_table_users) == 1)
+ if (!freq_table)
result = opp_init_cpufreq_table(mpu_dev, &freq_table);
if (result) {
goto fail_ck;
}
+ atomic_inc_return(&freq_table_users);
+
result = cpufreq_frequency_table_cpuinfo(policy, freq_table);
if (result)
goto fail_table;
#ifdef CONFIG_ARCH_NEEDS_CPU_IDLE_COUPLED
void cpuidle_coupled_parallel_barrier(struct cpuidle_device *dev, atomic_t *a);
+#else
+static inline void cpuidle_coupled_parallel_barrier(struct cpuidle_device *dev, atomic_t *a)
+{
+}
#endif
/******************************
#define MV643XX_ETH_SIZE_REG_4 0x2224
#define MV643XX_ETH_BASE_ADDR_ENABLE_REG 0x2290
+#define MV643XX_TX_CSUM_DEFAULT_LIMIT 0
+
struct mv643xx_eth_shared_platform_data {
struct mbus_dram_target_info *dram;
struct platform_device *shared_smi;
projects / ~andy / linux / commitdiff