0x00000008: Use fixed channel:
Use automatic channel selection when unset
Use DMA request line number when set
+ 0x00000010: Set channel as high priority:
+ Normal priority when unset
+ High priority when set
Example:
kirkwood-mplcec4.dtb \
kirkwood-mv88f6281gtw-ge.dtb \
kirkwood-netgear_readynas_duo_v2.dtb \
+ kirkwood-netgear_readynas_nv+_v2.dtb \
kirkwood-ns2.dtb \
kirkwood-ns2lite.dtb \
kirkwood-ns2max.dtb \
armada-xp-axpwifiap.dtb \
armada-xp-db.dtb \
armada-xp-gp.dtb \
+ armada-xp-netgear-rn2120.dtb \
armada-xp-matrix.dtb \
armada-xp-openblocks-ax3-4.dtb
dtb-$(CONFIG_ARCH_MXC) += \
green_pwr_led {
label = "mirabox:green:pwr";
gpios = <&gpio1 31 1>;
- linux,default-trigger = "heartbeat";
+ default-state = "keep";
};
blue_stat_led {
label = "mirabox:blue:stat";
gpios = <&gpio2 0 1>;
- linux,default-trigger = "cpu0";
+ default-state = "off";
};
green_stat_led {
reg = <0x25>;
};
};
+
+ nand@d0000 {
+ status = "okay";
+ num-cs = <1>;
+ marvell,nand-keep-config;
+ marvell,nand-enable-arbiter;
+ nand-on-flash-bbt;
+
+ partition@0 {
+ label = "U-Boot";
+ reg = <0 0x400000>;
+ };
+ partition@400000 {
+ label = "Linux";
+ reg = <0x400000 0x400000>;
+ };
+ partition@800000 {
+ label = "Filesystem";
+ reg = <0x800000 0x3f800000>;
+ };
+ };
};
};
};
/dts-v1/;
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
#include "armada-370.dtsi"
/ {
marvell,pins = "mpp57";
marvell,function = "gpio";
};
+
sata1_led_pin: sata1-led-pin {
marvell,pins = "mpp15";
marvell,function = "gpio";
marvell,function = "gpio";
};
+ backup_button_pin: backup-button-pin {
+ marvell,pins = "mpp58";
+ marvell,function = "gpio";
+ };
+
+ power_button_pin: power-button-pin {
+ marvell,pins = "mpp62";
+ marvell,function = "gpio";
+ };
+
+ reset_button_pin: reset-button-pin {
+ marvell,pins = "mpp6";
+ marvell,function = "gpio";
+ };
+
poweroff: poweroff {
marvell,pins = "mpp8";
marvell,function = "gpio";
};
mdio {
- phy0: ethernet-phy@0 {
+ phy0: ethernet-phy@0 { /* Marvell 88E1318 */
reg = <0>;
};
};
};
clocks {
- #address-cells = <1>;
- #size-cells = <0>;
-
- g762_clk: fixedclk {
+ g762_clk: g762-oscillator {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <8192>;
};
};
- gpio_leds {
+ gpio-leds {
compatible = "gpio-leds";
- pinctrl-0 = < &power_led_pin
- &sata1_led_pin
- &sata2_led_pin
- &backup_led_pin >;
+ pinctrl-0 = <&power_led_pin
+ &sata1_led_pin
+ &sata2_led_pin
+ &backup_led_pin>;
pinctrl-names = "default";
- blue_power_led {
+ blue-power-led {
label = "rn102:blue:pwr";
- gpios = <&gpio1 25 1>; /* GPIO 57 Active Low */
- linux,default-trigger = "heartbeat";
+ gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+ default-state = "keep";
};
- green_sata1_led {
+ green-sata1-led {
label = "rn102:green:sata1";
- gpios = <&gpio0 15 1>; /* GPIO 15 Active Low */
+ gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
default-state = "on";
};
- green_sata2_led {
+ green-sata2-led {
label = "rn102:green:sata2";
- gpios = <&gpio0 14 1>; /* GPIO 14 Active Low */
+ gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
default-state = "on";
};
- green_backup_led {
+ green-backup-led {
label = "rn102:green:backup";
- gpios = <&gpio1 24 1>; /* GPIO 56 Active Low */
+ gpios = <&gpio1 24 GPIO_ACTIVE_LOW>;
default-state = "on";
};
};
- gpio_keys {
+ gpio-keys {
compatible = "gpio-keys";
- #address-cells = <1>;
- #size-cells = <0>;
+ pinctrl-0 = <&power_button_pin
+ &reset_button_pin
+ &backup_button_pin>;
+ pinctrl-names = "default";
- button@1 {
+ power-button {
label = "Power Button";
- linux,code = <116>; /* KEY_POWER */
- gpios = <&gpio1 30 0>;
+ linux,code = <KEY_POWER>;
+ gpios = <&gpio1 30 GPIO_ACTIVE_HIGH>;
};
- button@2 {
+ reset-button {
label = "Reset Button";
- linux,code = <0x198>; /* KEY_RESTART */
- gpios = <&gpio0 6 1>;
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
};
- button@3 {
+ backup-button {
label = "Backup Button";
- linux,code = <133>; /* KEY_COPY */
- gpios = <&gpio1 26 1>;
+ linux,code = <KEY_COPY>;
+ gpios = <&gpio1 26 GPIO_ACTIVE_LOW>;
};
};
- gpio_poweroff {
+ gpio-poweroff {
compatible = "gpio-poweroff";
pinctrl-0 = <&poweroff>;
pinctrl-names = "default";
- gpios = <&gpio0 8 1>;
+ gpios = <&gpio0 8 GPIO_ACTIVE_LOW>;
};
-
};
/dts-v1/;
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
#include "armada-370.dtsi"
/ {
marvell,function = "gpio";
};
- backup_key_pin: backup-key-pin {
+ backup_button_pin: backup-button-pin {
marvell,pins = "mpp52";
marvell,function = "gpio";
};
- power_key_pin: power-key-pin {
+ power_button_pin: power-button-pin {
marvell,pins = "mpp62";
marvell,function = "gpio";
};
marvell,function = "gpio";
};
- reset_key_pin: reset-key-pin {
+ reset_button_pin: reset-button-pin {
marvell,pins = "mpp65";
marvell,function = "gpio";
};
};
mdio {
- phy0: ethernet-phy@0 {
+ phy0: ethernet-phy@0 { /* Marvell 88E1318 */
reg = <0>;
};
- phy1: ethernet-phy@1 {
+ phy1: ethernet-phy@1 { /* Marvell 88E1318 */
reg = <1>;
};
};
fan_startv = <1>;
pwm_polarity = <0>;
};
+
+ pca9554: pca9554@23 {
+ compatible = "nxp,pca9554";
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x23>;
+ };
};
};
};
clocks {
- #address-cells = <1>;
- #size-cells = <0>;
-
- g762_clk: fixedclk {
+ g762_clk: g762-oscillator {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <8192>;
};
};
- gpio_leds {
+ gpio-leds {
compatible = "gpio-leds";
pinctrl-0 = <&backup_led_pin &power_led_pin>;
pinctrl-names = "default";
- blue_backup_led {
+ blue-backup-led {
label = "rn104:blue:backup";
- gpios = <&gpio1 31 0>; /* GPIO 63 Active High */
+ gpios = <&gpio1 31 GPIO_ACTIVE_HIGH>;
default-state = "off";
};
- blue_power_led {
+ blue-power-led {
label = "rn104:blue:pwr";
- gpios = <&gpio2 0 1>; /* GPIO 64 Active Low */
+ gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
linux,default-trigger = "keep";
};
+
+ blue-sata1-led {
+ label = "rn104:blue:sata1";
+ gpios = <&pca9554 0 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+
+ blue-sata2-led {
+ label = "rn104:blue:sata2";
+ gpios = <&pca9554 1 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+
+ blue-sata3-led {
+ label = "rn104:blue:sata3";
+ gpios = <&pca9554 2 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+
+ blue-sata4-led {
+ label = "rn104:blue:sata4";
+ gpios = <&pca9554 3 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
};
- gpio_keys {
+ gpio-keys {
compatible = "gpio-keys";
- #address-cells = <1>;
- #size-cells = <0>;
- pinctrl-0 = <&backup_key_pin
- &power_key_pin
- &reset_key_pin>;
+ pinctrl-0 = <&backup_button_pin
+ &power_button_pin
+ &reset_button_pin>;
pinctrl-names = "default";
- button@1 {
+ backup-button {
label = "Backup Button";
- linux,code = <133>; /* KEY_COPY */
- gpios = <&gpio1 20 1>;
+ linux,code = <KEY_COPY>;
+ gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
};
- button@2 {
+ power-button {
label = "Power Button";
- linux,code = <116>; /* KEY_POWER */
- gpios = <&gpio1 30 0>;
+ linux,code = <KEY_POWER>;
+ gpios = <&gpio1 30 GPIO_ACTIVE_HIGH>;
};
- button@3 {
+ reset-button {
label = "Reset Button";
- linux,code = <0x198>; /* KEY_RESTART */
- gpios = <&gpio2 1 1>;
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
};
};
- gpio_poweroff {
+ gpio-poweroff {
compatible = "gpio-poweroff";
pinctrl-0 = <&poweroff>;
pinctrl-names = "default";
- gpios = <&gpio1 28 1>;
+ gpios = <&gpio1 28 GPIO_ACTIVE_LOW>;
};
};
status = "disabled";
};
+ nand@d0000 {
+ compatible = "marvell,armada370-nand";
+ reg = <0xd0000 0x54>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ interrupts = <113>;
+ clocks = <&coredivclk 0>;
+ status = "disabled";
+ };
};
};
spi-max-frequency = <108000000>;
};
};
+
+ nand@d0000 {
+ status = "okay";
+ num-cs = <1>;
+ marvell,nand-keep-config;
+ marvell,nand-enable-arbiter;
+ nand-on-flash-bbt;
+ };
};
};
};
--- /dev/null
+/*
+ * Device Tree file for NETGEAR ReadyNAS 2120
+ *
+ * Copyright (C) 2013, Arnaud EBALARD <arno@natisbad.org>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "armada-xp-mv78230.dtsi"
+
+/ {
+ model = "NETGEAR ReadyNAS 2120";
+ compatible = "netgear,readynas-2120", "marvell,armadaxp-mv78230", "marvell,armadaxp", "marvell,armada-370-xp";
+
+ chosen {
+ bootargs = "console=ttyS0,115200 earlyprintk";
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0 0x00000000 0 0x80000000>; /* 2GB */
+ };
+
+ soc {
+ ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xd0000000 0x100000
+ MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000>;
+
+ pcie-controller {
+ status = "okay";
+
+ /* Connected to first Marvell 88SE9170 SATA controller */
+ pcie@1,0 {
+ /* Port 0, Lane 0 */
+ status = "okay";
+ };
+
+ /* Connected to second Marvell 88SE9170 SATA controller */
+ pcie@2,0 {
+ /* Port 0, Lane 1 */
+ status = "okay";
+ };
+
+ /* Connected to Fresco Logic FL1009 USB 3.0 controller */
+ pcie@5,0 {
+ /* Port 1, Lane 0 */
+ status = "okay";
+ };
+ };
+
+ internal-regs {
+ pinctrl {
+ poweroff: poweroff {
+ marvell,pins = "mpp42";
+ marvell,function = "gpio";
+ };
+
+ power_button_pin: power-button-pin {
+ marvell,pins = "mpp27";
+ marvell,function = "gpio";
+ };
+
+ reset_button_pin: reset-button-pin {
+ marvell,pins = "mpp41";
+ marvell,function = "gpio";
+ };
+
+ sata1_led_pin: sata1-led-pin {
+ marvell,pins = "mpp31";
+ marvell,function = "gpio";
+ };
+
+ sata2_led_pin: sata2-led-pin {
+ marvell,pins = "mpp40";
+ marvell,function = "gpio";
+ };
+
+ sata3_led_pin: sata3-led-pin {
+ marvell,pins = "mpp44";
+ marvell,function = "gpio";
+ };
+
+ sata4_led_pin: sata4-led-pin {
+ marvell,pins = "mpp47";
+ marvell,function = "gpio";
+ };
+
+ sata1_power_pin: sata1-power-pin {
+ marvell,pins = "mpp24";
+ marvell,function = "gpio";
+ };
+
+ sata2_power_pin: sata2-power-pin {
+ marvell,pins = "mpp25";
+ marvell,function = "gpio";
+ };
+
+ sata3_power_pin: sata3-power-pin {
+ marvell,pins = "mpp26";
+ marvell,function = "gpio";
+ };
+
+ sata4_power_pin: sata4-power-pin {
+ marvell,pins = "mpp28";
+ marvell,function = "gpio";
+ };
+
+ sata1_pres_pin: sata1-pres-pin {
+ marvell,pins = "mpp32";
+ marvell,function = "gpio";
+ };
+
+ sata2_pres_pin: sata2-pres-pin {
+ marvell,pins = "mpp33";
+ marvell,function = "gpio";
+ };
+
+ sata3_pres_pin: sata3-pres-pin {
+ marvell,pins = "mpp34";
+ marvell,function = "gpio";
+ };
+
+ sata4_pres_pin: sata4-pres-pin {
+ marvell,pins = "mpp35";
+ marvell,function = "gpio";
+ };
+
+ err_led_pin: err-led-pin {
+ marvell,pins = "mpp45";
+ marvell,function = "gpio";
+ };
+ };
+
+ serial@12000 {
+ clocks = <&coreclk 0>;
+ status = "okay";
+ };
+
+ mdio {
+ phy0: ethernet-phy@0 { /* Marvell 88E1318 */
+ reg = <0>;
+ };
+
+ phy1: ethernet-phy@1 { /* Marvell 88E1318 */
+ reg = <1>;
+ };
+ };
+
+ ethernet@70000 {
+ status = "okay";
+ phy = <&phy0>;
+ phy-mode = "rgmii-id";
+ };
+
+ ethernet@74000 {
+ status = "okay";
+ phy = <&phy1>;
+ phy-mode = "rgmii-id";
+ };
+
+ /* Front USB 2.0 port */
+ usb@50000 {
+ status = "okay";
+ };
+
+ i2c@11000 {
+ compatible = "marvell,mv64xxx-i2c";
+ clock-frequency = <400000>;
+ status = "okay";
+
+ /* Controller for rear fan #1 of 3 (Protechnic
+ * MGT4012XB-O20, 8000RPM) near eSATA port */
+ g762_fan1: g762@3e {
+ compatible = "gmt,g762";
+ reg = <0x3e>;
+ clocks = <&g762_clk>; /* input clock */
+ fan_gear_mode = <0>;
+ fan_startv = <1>;
+ pwm_polarity = <0>;
+ };
+
+ /* Controller for rear (center) fan #2 of 3 */
+ g762_fan2: g762@48 {
+ compatible = "gmt,g762";
+ reg = <0x48>;
+ clocks = <&g762_clk>; /* input clock */
+ fan_gear_mode = <0>;
+ fan_startv = <1>;
+ pwm_polarity = <0>;
+ };
+
+ /* Controller for rear fan #3 of 3 */
+ g762_fan3: g762@49 {
+ compatible = "gmt,g762";
+ reg = <0x49>;
+ clocks = <&g762_clk>; /* input clock */
+ fan_gear_mode = <0>;
+ fan_startv = <1>;
+ pwm_polarity = <0>;
+ };
+
+ /* Temperature sensor */
+ g751: g751@4c {
+ compatible = "gmt,g751";
+ reg = <0x4c>;
+ };
+ };
+ };
+ };
+
+ clocks {
+ g762_clk: g762-oscillator {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&sata1_led_pin &sata2_led_pin &err_led_pin
+ &sata3_led_pin &sata4_led_pin>;
+ pinctrl-names = "default";
+
+ red-sata1-led {
+ label = "rn2120:red:sata1";
+ gpios = <&gpio0 31 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ red-sata2-led {
+ label = "rn2120:red:sata2";
+ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ red-sata3-led {
+ label = "rn2120:red:sata3";
+ gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ red-sata4-led {
+ label = "rn2120:red:sata4";
+ gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ red-err-led {
+ label = "rn2120:red:err";
+ gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&power_button_pin &reset_button_pin>;
+ pinctrl-names = "default";
+
+ power-button {
+ label = "Power Button";
+ linux,code = <KEY_POWER>;
+ gpios = <&gpio0 27 GPIO_ACTIVE_HIGH>;
+ };
+
+ reset-button {
+ label = "Reset Button";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ gpio-poweroff {
+ compatible = "gpio-poweroff";
+ pinctrl-0 = <&poweroff>;
+ pinctrl-names = "default";
+ gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
+ };
+};
green_led {
label = "green_led";
gpios = <&gpio1 21 1>;
- default-state = "off";
- linux,default-trigger = "heartbeat";
+ default-state = "keep";
};
};
power {
label = "Power";
gpios = <&gpio0 18 1>;
- linux,default-trigger = "default-on";
+ default-state = "keep";
};
};
marvell,#interrupts = <5>;
};
+ pmu_intc: pmu-interrupt-ctrl@d0050 {
+ compatible = "marvell,dove-pmu-intc";
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ reg = <0xd0050 0x8>;
+ interrupts = <33>;
+ marvell,#interrupts = <7>;
+ };
+
core_clk: core-clocks@d0214 {
compatible = "marvell,dove-core-clock";
reg = <0xd0214 0x4>;
rtc: real-time-clock@d8500 {
compatible = "marvell,orion-rtc";
reg = <0xd8500 0x20>;
+ interrupt-parent = <&pmu_intc>;
+ interrupts = <5>;
};
crypto: crypto-engine@30000 {
status = "disabled";
ethphy: ethernet-phy {
- device-type = "ethernet-phy";
+ device_type = "ethernet-phy";
/* set phy address in board file */
};
};
reg = <0x90000 0x200>;
interrupts = <28>;
clocks = <&gate_clk 4>;
+ pinctrl-0 = <&pmx_sdio>;
+ pinctrl-names = "default";
bus-width = <4>;
cap-sdio-irq;
cap-sd-highspeed;
reg = <0x90000 0x200>;
interrupts = <28>;
clocks = <&gate_clk 4>;
+ pinctrl-0 = <&pmx_sdio>;
+ pinctrl-names = "default";
bus-width = <4>;
cap-sdio-irq;
cap-sd-highspeed;
blue-power {
label = "dns320:blue:power";
gpios = <&gpio0 26 1>; /* GPIO 26 Active Low */
- linux,default-trigger = "default-on";
+ default-state = "keep";
};
blue-usb {
label = "dns320:blue:usb";
white-power {
label = "dns325:white:power";
gpios = <&gpio0 26 1>; /* GPIO 26 Active Low */
- linux,default-trigger = "default-on";
+ default-state = "keep";
};
white-usb {
label = "dns325:white:usb";
health {
label = "status:green:health";
gpios = <&gpio1 14 1>;
- linux,default-trigger = "default-on";
+ default-state = "keep";
};
fault {
label = "status:orange:fault";
health {
label = "status:green:health";
gpios = <&gpio1 14 1>;
- linux,default-trigger = "default-on";
+ default-state = "keep";
};
fault {
label = "status:orange:fault";
nr-ports = <1>;
};
+ /* AzureWave AW-GH381 WiFi/BT */
mvsdio@90000 {
status = "okay";
- /* No CD or WP GPIOs */
- broken-cd;
+ non-removable;
};
};
green-os {
label = "ib62x0:green:os";
gpios = <&gpio0 25 0>;
- linux,default-trigger = "default-on";
+ default-state = "keep";
};
red-os {
label = "ib62x0:red:os";
led-level {
label = "led_level";
gpios = <&gpio1 9 0>;
- linux,default-trigger = "default-on";
+ default-state = "on";
};
power-blue {
label = "power:blue";
gpios = <&gpio1 10 0>;
- linux,default-trigger = "timer";
+ default-state = "keep";
};
power-red {
label = "power:red";
power_led {
label = "status:white:power_led";
gpios = <&gpio0 16 0>;
- linux,default-trigger = "default-on";
+ default-state = "keep";
};
rebuild_led {
label = "status:white:rebuild_led";
led@4 {
label = "lsxl:blue:power";
gpios = <&gpio1 7 1>;
- linux,default-trigger = "default-on";
+ default-state = "keep";
};
led@5 {
+/*
+ * Device Tree file for NETGEAR ReadyNAS Duo v2
+ *
+ * Copyright (C) 2013, Arnaud EBALARD <arno@natisbad.org>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+
/dts-v1/;
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
#include "kirkwood.dtsi"
#include "kirkwood-6282.dtsi"
marvell,pins = "mpp47";
marvell,function = "gpio";
};
+
pmx_button_backup: pmx-button-backup {
marvell,pins = "mpp45";
marvell,function = "gpio";
};
+
pmx_button_reset: pmx-button-reset {
marvell,pins = "mpp13";
marvell,function = "gpio";
};
+
pmx_led_blue_power: pmx-led-blue-power {
marvell,pins = "mpp31";
marvell,function = "gpio";
};
+
pmx_led_blue_activity: pmx-led-blue-activity {
marvell,pins = "mpp38";
marvell,function = "gpio";
};
+
pmx_led_blue_disk1: pmx-led-blue-disk1 {
marvell,pins = "mpp23";
marvell,function = "gpio";
};
+
pmx_led_blue_disk2: pmx-led-blue-disk2 {
marvell,pins = "mpp22";
marvell,function = "gpio";
};
+
pmx_led_blue_backup: pmx-led-blue-backup {
marvell,pins = "mpp29";
marvell,function = "gpio";
};
+
+ pmx_poweroff: pmx-poweroff {
+ marvell,pins = "mpp30";
+ marvell,function = "gpio";
+ };
};
clocks {
- #address-cells = <1>;
- #size-cells = <0>;
-
- g762_clk: fixedclk {
+ g762_clk: g762-oscillator {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <8192>;
power_led {
label = "status:blue:power_led";
- gpios = <&gpio0 31 1>; /* GPIO 31 Active Low */
- linux,default-trigger = "default-on";
+ gpios = <&gpio0 31 GPIO_ACTIVE_LOW>;
+ default-state = "keep";
};
+
activity_led {
label = "status:blue:activity_led";
- gpios = <&gpio1 6 1>; /* GPIO 38 Active Low */
+ gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
};
+
disk1_led {
label = "status:blue:disk1_led";
- gpios = <&gpio0 23 1>; /* GPIO 23 Active Low */
+ gpios = <&gpio0 23 GPIO_ACTIVE_LOW>;
};
+
disk2_led {
label = "status:blue:disk2_led";
- gpios = <&gpio0 22 1>; /* GPIO 22 Active Low */
+ gpios = <&gpio0 22 GPIO_ACTIVE_LOW>;
};
+
backup_led {
label = "status:blue:backup_led";
- gpios = <&gpio0 29 1>; /* GPIO 29 Active Low*/
+ gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
};
};
- gpio_keys {
+ gpio-keys {
compatible = "gpio-keys";
- #address-cells = <1>;
- #size-cells = <0>;
pinctrl-0 = <&pmx_button_power &pmx_button_backup
&pmx_button_reset>;
pinctrl-names = "default";
- button@1 {
+ power-button {
label = "Power Button";
- linux,code = <116>; /* KEY_POWER */
- gpios = <&gpio1 15 1>;
+ linux,code = <KEY_POWER>;
+ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
};
- button@2 {
+
+ reset-button {
label = "Reset Button";
- linux,code = <0x198>; /* KEY_RESTART */
- gpios = <&gpio0 13 1>;
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
};
- button@3 {
+
+ backup-button {
label = "Backup Button";
- linux,code = <133>; /* KEY_COPY */
- gpios = <&gpio1 13 1>;
+ linux,code = <KEY_COPY>;
+ gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
};
};
- regulators {
- compatible = "simple-bus";
- #address-cells = <1>;
- #size-cells = <0>;
-
- usb_power: regulator@1 {
- compatible = "regulator-fixed";
- reg = <1>;
- regulator-name = "USB 3.0 Power";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- enable-active-high;
- regulator-always-on;
- regulator-boot-on;
- gpio = <&gpio1 14 0>;
- };
- };
+ gpio-poweroff {
+ compatible = "gpio-poweroff";
+ pinctrl-0 = <&pmx_poweroff>;
+ pinctrl-names = "default";
+ gpios = <&gpio0 30 GPIO_ACTIVE_LOW>;
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usb3_regulator: usb3-regulator {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "USB 3.0 Power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio1 14 GPIO_ACTIVE_HIGH>;
+ };
+ };
};
&nand {
&mdio {
status = "okay";
- ethphy0: ethernet-phy@0 {
+ ethphy0: ethernet-phy@0 { /* Marvell 88E1318 */
device_type = "ethernet-phy";
reg = <0>;
};
--- /dev/null
+/*
+ * Device Tree file for NETGEAR ReadyNAS NV+ v2
+ *
+ * Copyright (C) 2013, Arnaud EBALARD <arno@natisbad.org>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "kirkwood.dtsi"
+#include "kirkwood-6282.dtsi"
+
+/ {
+ model = "NETGEAR ReadyNAS NV+ v2";
+ compatible = "netgear,readynas-nv+-v2", "netgear,readynas", "marvell,kirkwood-88f6282", "marvell,kirkwood";
+
+ memory { /* 256 MB */
+ device_type = "memory";
+ reg = <0x00000000 0x10000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8 earlyprintk";
+ };
+
+ mbus {
+ pcie-controller {
+ status = "okay";
+
+ /* Connected to NEC uPD720200 USB 3.0 controller */
+ pcie@1,0 {
+ /* Port 0, Lane 0 */
+ status = "okay";
+ };
+ };
+ };
+
+ ocp@f1000000 {
+ pinctrl: pinctrl@10000 {
+ pmx_button_power: pmx-button-power {
+ marvell,pins = "mpp47";
+ marvell,function = "gpio";
+ };
+
+ pmx_button_backup: pmx-button-backup {
+ marvell,pins = "mpp45";
+ marvell,function = "gpio";
+ };
+
+ pmx_button_reset: pmx-button-reset {
+ marvell,pins = "mpp13";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_blue_power: pmx-led-blue-power {
+ marvell,pins = "mpp31";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_blue_backup: pmx-led-blue-backup {
+ marvell,pins = "mpp22";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_blue_disk1: pmx-led-blue-disk1 {
+ marvell,pins = "mpp20";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_blue_disk2: pmx-led-blue-disk2 {
+ marvell,pins = "mpp23";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_blue_disk3: pmx-led-blue-disk3 {
+ marvell,pins = "mpp24";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_blue_disk4: pmx-led-blue-disk4 {
+ marvell,pins = "mpp29";
+ marvell,function = "gpio";
+ };
+
+ pmx_poweroff: pmx-poweroff {
+ marvell,pins = "mpp30";
+ marvell,function = "gpio";
+ };
+ };
+
+ clocks {
+ g762_clk: g762-oscillator {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <8192>;
+ };
+ };
+
+ i2c@11000 {
+ status = "okay";
+
+ rs5c372a: rs5c372a@32 {
+ compatible = "ricoh,rs5c372a";
+ reg = <0x32>;
+ };
+
+ g762: g762@3e {
+ compatible = "gmt,g762";
+ reg = <0x3e>;
+ clocks = <&g762_clk>; /* input clock */
+ fan_gear_mode = <0>;
+ fan_startv = <1>;
+ pwm_polarity = <0>;
+ };
+ };
+
+ serial@12000 {
+ pinctrl-0 = <&pmx_uart0>;
+ pinctrl-names = "default";
+ status = "okay";
+ };
+
+ sata@80000 { /* Connected to Marvell 88SM4140 SATA port multiplier */
+ status = "okay";
+ nr-ports = <1>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = < &pmx_led_blue_power &pmx_led_blue_backup
+ &pmx_led_blue_disk1 &pmx_led_blue_disk2
+ &pmx_led_blue_disk3 &pmx_led_blue_disk3 >;
+ pinctrl-names = "default";
+
+ power_led {
+ label = "status:blue:power_led";
+ gpios = <&gpio0 31 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "default-on";
+ };
+
+ backup_led {
+ label = "status:blue:backup_led";
+ gpios = <&gpio0 22 GPIO_ACTIVE_LOW>;
+ };
+
+ disk1_led {
+ label = "status:blue:disk1_led";
+ gpios = <&gpio0 20 GPIO_ACTIVE_LOW>;
+ };
+
+ disk2_led {
+ label = "status:blue:disk2_led";
+ gpios = <&gpio0 23 GPIO_ACTIVE_LOW>;
+ };
+
+ disk3_led {
+ label = "status:blue:disk3_led";
+ gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
+ };
+
+ disk4_led {
+ label = "status:blue:disk4_led";
+ gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&pmx_button_power &pmx_button_backup
+ &pmx_button_reset>;
+ pinctrl-names = "default";
+
+ power-button {
+ label = "Power Button";
+ linux,code = <KEY_POWER>;
+ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+ };
+
+ reset-button {
+ label = "Reset Button";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
+ };
+
+ backup-button {
+ label = "Backup Button";
+ linux,code = <KEY_COPY>;
+ gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ gpio-poweroff {
+ compatible = "gpio-poweroff";
+ pinctrl-0 = <&pmx_poweroff>;
+ pinctrl-names = "default";
+ gpios = <&gpio0 30 GPIO_ACTIVE_LOW>;
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usb3_regulator: usb3-regulator {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "USB 3.0 Power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio1 14 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&nand {
+ status = "okay";
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0000000 0x180000>;
+ read-only;
+ };
+
+ partition@180000 {
+ label = "u-boot-env";
+ reg = <0x180000 0x20000>;
+ };
+
+ partition@200000 {
+ label = "uImage";
+ reg = <0x0200000 0x600000>;
+ };
+
+ partition@800000 {
+ label = "minirootfs";
+ reg = <0x0800000 0x1000000>;
+ };
+
+ partition@1800000 {
+ label = "jffs2";
+ reg = <0x1800000 0x6800000>;
+ };
+};
+
+&mdio {
+ status = "okay";
+
+ ethphy0: ethernet-phy@0 { /* Marvell 88E1318 */
+ device_type = "ethernet-phy";
+ reg = <0>;
+ };
+};
+
+ð0 {
+ status = "okay";
+
+ ethernet0-port@0 {
+ phy-handle = <ðphy0>;
+ };
+};
blue-sata {
label = "ns2:blue:sata";
gpios = <&gpio0 30 1>;
- linux,default-trigger = "default-on";
+ linux,default-trigger = "ide-disk";
};
};
};
/*
- * kirkwood-sheevaplug-common.dts - Common parts for Sheevaplugs
+ * kirkwood-sheevaplug-common.dtsi - Common parts for Sheevaplugs
*
* Copyright (C) 2013 Simon Baatz <gmbnomis@gmail.com>
*
health {
label = "sheevaplug:blue:health";
gpios = <&gpio1 17 1>;
- linux,default-trigger = "default-on";
+ default-state = "keep";
};
};
};
/*
- * kirkwood-sheevaplug-esata.dts - Device tree file for Sheevaplug
+ * kirkwood-sheevaplug.dts - Device tree file for Sheevaplug
*
* Copyright (C) 2013 Simon Baatz <gmbnomis@gmail.com>
*
health {
label = "sheevaplug:blue:health";
gpios = <&gpio1 17 1>;
- linux,default-trigger = "default-on";
+ default-state = "keep";
};
misc {
status = "okay";
ethphy: ethernet-phy {
- device-type = "ethernet-phy";
+ device_type = "ethernet-phy";
reg = <8>;
};
};
/* Pull Up */
#define PU (1 << 26)
/* Open Drain */
-#define OD (1 << 26)
+#define OD (1 << 25)
#define RT (1 << 23)
#define INVERTCLK (1 << 22)
#define CLKNOTDATA (1 << 21)
interrupts = <0 31 IRQ_TYPE_LEVEL_HIGH>;
v-ape-supply = <&db8500_vape_reg>;
+ dmas = <&dma 31 0 0x12>, /* Logical - DevToMem - HighPrio */
+ <&dma 31 0 0x10>; /* Logical - MemToDev - HighPrio */
+ dma-names = "rx", "tx";
+
clocks = <&prcc_kclk 1 3>, <&prcc_pclk 1 3>;
clock-names = "msp", "apb_pclk";
interrupts = <0 62 IRQ_TYPE_LEVEL_HIGH>;
v-ape-supply = <&db8500_vape_reg>;
+ dmas = <&dma 30 0 0x10>; /* Logical - MemToDev - HighPrio */
+ dma-names = "tx";
+
clocks = <&prcc_kclk 1 4>, <&prcc_pclk 1 4>;
clock-names = "msp", "apb_pclk";
interrupts = <0 98 IRQ_TYPE_LEVEL_HIGH>;
v-ape-supply = <&db8500_vape_reg>;
+ dmas = <&dma 14 0 0x12>, /* Logical - DevToMem - HighPrio */
+ <&dma 14 1 0x19>; /* Physical Chan 1 - MemToDev
+ HighPrio - Fixed */
+ dma-names = "rx", "tx";
+
clocks = <&prcc_kclk 2 3>, <&prcc_pclk 2 5>;
clock-names = "msp", "apb_pclk";
interrupts = <0 62 IRQ_TYPE_LEVEL_HIGH>;
v-ape-supply = <&db8500_vape_reg>;
+ dmas = <&dma 30 0 0x12>; /* Logical - DevToMem - HighPrio */
+ dma-names = "rx";
+
clocks = <&prcc_kclk 1 10>, <&prcc_pclk 1 11>;
clock-names = "msp", "apb_pclk";
status = "disabled";
};
+ mcde@a0350000 {
+ compatible = "stericsson,mcde";
+ reg = <0xa0350000 0x1000>, /* MCDE */
+ <0xa0351000 0x1000>, /* DSI link 1 */
+ <0xa0352000 0x1000>, /* DSI link 2 */
+ <0xa0353000 0x1000>; /* DSI link 3 */
+ interrupts = <0 48 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&prcmu_clk PRCMU_MCDECLK>, /* Main MCDE clock */
+ <&prcmu_clk PRCMU_LCDCLK>, /* LCD clock */
+ <&prcmu_clk PRCMU_PLLDSI>, /* HDMI clock */
+ <&prcmu_clk PRCMU_DSI0CLK>, /* DSI 0 */
+ <&prcmu_clk PRCMU_DSI1CLK>, /* DSI 1 */
+ <&prcmu_clk PRCMU_DSI0ESCCLK>, /* TVout clock 0 */
+ <&prcmu_clk PRCMU_DSI1ESCCLK>, /* TVout clock 1 */
+ <&prcmu_clk PRCMU_DSI2ESCCLK>; /* TVout clock 2 */
+ };
+
cryp@a03cb000 {
compatible = "stericsson,ux500-cryp";
reg = <0xa03cb000 0x1000>;
--- /dev/null
+/*
+ * Copyright 2013 Linaro Ltd.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#include "ste-nomadik-pinctrl.dtsi"
+
+/ {
+ soc {
+ pinctrl {
+ /* Settings for all UART default and sleep states */
+ uart0 {
+ uart0_default_mode: uart0_default {
+ default_mux {
+ ste,function = "u0";
+ ste,pins = "u0_a_1";
+ };
+ default_cfg1 {
+ ste,pins = "GPIO0_AJ5", "GPIO2_AH4"; /* CTS+RXD */
+ ste,config = <&in_pu>;
+ };
+
+ default_cfg2 {
+ ste,pins = "GPIO1_AJ3", "GPIO3_AH3"; /* RTS+TXD */
+ ste,config = <&out_hi>;
+ };
+ };
+
+ uart0_sleep_mode: uart0_sleep {
+ sleep_cfg1 {
+ ste,pins = "GPIO0_AJ5", "GPIO2_AH4"; /* CTS+RXD */
+ ste,config = <&slpm_in_wkup_pdis>;
+ };
+
+ sleep_cfg2 {
+ ste,pins = "GPIO1_AJ3"; /* RTS */
+ ste,config = <&slpm_out_hi_wkup_pdis>;
+ };
+
+ sleep_cfg3 {
+ ste,pins = "GPIO3_AH3"; /* TXD */
+ ste,config = <&slpm_out_wkup_pdis>;
+ };
+ };
+ };
+
+ uart1 {
+ uart1_default_mode: uart1_default {
+ default_mux {
+ ste,function = "u1";
+ ste,pins = "u1rxtx_a_1";
+ };
+ default_cfg1 {
+ ste,pins = "GPIO4_AH6"; /* RXD */
+ ste,config = <&in_pu>;
+ };
+
+ default_cfg2 {
+ ste,pins = "GPIO5_AG6"; /* TXD */
+ ste,config = <&out_hi>;
+ };
+ };
+
+ uart1_sleep_mode: uart1_sleep {
+ sleep_cfg1 {
+ ste,pins = "GPIO4_AH6"; /* RXD */
+ ste,config = <&slpm_in_wkup_pdis>;
+ };
+
+ sleep_cfg2 {
+ ste,pins = "GPIO5_AG6"; /* TXD */
+ ste,config = <&slpm_out_wkup_pdis>;
+ };
+ };
+ };
+
+ uart2 {
+ uart2_default_mode: uart2_default {
+ default_mux {
+ ste,function = "u2";
+ ste,pins = "u2rxtx_c_1";
+ };
+ default_cfg1 {
+ ste,pins = "GPIO29_W2"; /* RXD */
+ ste,config = <&in_pu>;
+ };
+
+ default_cfg2 {
+ ste,pins = "GPIO30_W3"; /* TXD */
+ ste,config = <&out_hi>;
+ };
+ };
+
+ uart2_sleep_mode: uart2_sleep {
+ sleep_cfg1 {
+ ste,pins = "GPIO29_W2"; /* RXD */
+ ste,config = <&in_wkup_pdis>;
+ };
+
+ sleep_cfg2 {
+ ste,pins = "GPIO30_W3"; /* TXD */
+ ste,config = <&out_wkup_pdis>;
+ };
+ };
+ };
+
+ /* Settings for all I2C default and sleep states */
+ i2c0 {
+ i2c0_default_mode: i2c_default {
+ default_mux {
+ ste,function = "i2c0";
+ ste,pins = "i2c0_a_1";
+ };
+ default_cfg1 {
+ ste,pins = "GPIO147_C15", "GPIO148_B16"; /* SDA/SCL */
+ ste,config = <&in_pu>;
+ };
+ };
+
+ i2c0_sleep_mode: i2c_sleep {
+ sleep_cfg1 {
+ ste,pins = "GPIO147_C15", "GPIO148_B16"; /* SDA/SCL */
+ ste,config = <&slpm_in_wkup_pdis>;
+ };
+ };
+ };
+
+ i2c1 {
+ i2c1_default_mode: i2c_default {
+ default_mux {
+ ste,function = "i2c1";
+ ste,pins = "i2c1_b_2";
+ };
+ default_cfg1 {
+ ste,pins = "GPIO16_AD3", "GPIO17_AD4"; /* SDA/SCL */
+ ste,config = <&in_pu>;
+ };
+ };
+
+ i2c1_sleep_mode: i2c_sleep {
+ sleep_cfg1 {
+ ste,pins = "GPIO16_AD3", "GPIO17_AD4"; /* SDA/SCL */
+ ste,config = <&slpm_in_wkup_pdis>;
+ };
+ };
+ };
+
+ i2c2 {
+ i2c2_default_mode: i2c_default {
+ default_mux {
+ ste,function = "i2c2";
+ ste,pins = "i2c2_b_2";
+ };
+ default_cfg1 {
+ ste,pins = "GPIO10_AF5", "GPIO11_AG4"; /* SDA/SCL */
+ ste,config = <&in_pu>;
+ };
+ };
+
+ i2c2_sleep_mode: i2c_sleep {
+ sleep_cfg1 {
+ ste,pins = "GPIO10_AF5", "GPIO11_AG4"; /* SDA/SCL */
+ ste,config = <&slpm_in_wkup_pdis>;
+ };
+ };
+ };
+
+ i2c3 {
+ i2c3_default_mode: i2c_default {
+ default_mux {
+ ste,function = "i2c3";
+ ste,pins = "i2c3_c_2";
+ };
+ default_cfg1 {
+ ste,pins = "GPIO229_AG7", "GPIO230_AF7"; /* SDA/SCL */
+ ste,config = <&in_pu>;
+ };
+ };
+
+ i2c3_sleep_mode: i2c_sleep {
+ sleep_cfg1 {
+ ste,pins = "GPIO229_AG7", "GPIO230_AF7"; /* SDA/SCL */
+ ste,config = <&slpm_in_wkup_pdis>;
+ };
+ };
+ };
+
+ /*
+ * Activating I2C4 will conflict with UART1 about the same pins so do not
+ * enable I2C4 and UART1 at the same time.
+ */
+ i2c4 {
+ i2c4_default_mode: i2c_default {
+ default_mux {
+ ste,function = "i2c4";
+ ste,pins = "i2c4_b_1";
+ };
+ default_cfg1 {
+ ste,pins = "GPIO4_AH6", "GPIO5_AG6"; /* SDA/SCL */
+ ste,config = <&in_pu>;
+ };
+ };
+
+ i2c4_sleep_mode: i2c_sleep {
+ sleep_cfg1 {
+ ste,pins = "GPIO4_AH6", "GPIO5_AG6"; /* SDA/SCL */
+ ste,config = <&slpm_in_wkup_pdis>;
+ };
+ };
+ };
+
+ /* Settings for all SPI default and sleep states */
+ spi2 {
+ spi2_default_mode: spi_default {
+ default_mux {
+ ste,function = "spi2";
+ ste,pins = "spi2_oc1_2";
+ };
+ default_cfg1 {
+ ste,pins = "GPIO216_AG12"; /* FRM */
+ ste,config = <&gpio_out_hi>;
+ };
+ default_cfg2 {
+ ste,pins = "GPIO218_AH11"; /* RXD */
+ ste,config = <&in_pd>;
+ };
+ default_cfg3 {
+ ste,pins =
+ "GPIO215_AH13", /* TXD */
+ "GPIO217_AH12"; /* CLK */
+ ste,config = <&out_lo>;
+ };
+ };
+
+ spi2_idle_mode: spi_idle {
+ /*
+ * The idle mode is basically sleep mode sans wakeups. Also
+ * note that we have muxes the pins off the function here
+ * as we do not state any muxing.
+ */
+ idle_cfg1 {
+ ste,pins = "GPIO218_AH11"; /* RXD */
+ ste,config = <&slpm_in_pdis>;
+ };
+ idle_cfg2 {
+ ste,pins = "GPIO215_AH13"; /* TXD */
+ ste,config = <&slpm_out_lo_pdis>;
+ };
+ idle_cfg3 {
+ ste,pins = "GPIO217_AH12"; /* CLK */
+ ste,config = <&slpm_pdis>;
+ };
+ };
+
+ spi2_sleep_mode: spi_sleep {
+ sleep_cfg1 {
+ ste,pins =
+ "GPIO216_AG12", /* FRM */
+ "GPIO218_AH11"; /* RXD */
+ ste,config = <&slpm_in_wkup_pdis>;
+ };
+ sleep_cfg2 {
+ ste,pins = "GPIO215_AH13"; /* TXD */
+ ste,config = <&slpm_out_lo_wkup_pdis>;
+ };
+ sleep_cfg3 {
+ ste,pins = "GPIO217_AH12"; /* CLK */
+ ste,config = <&slpm_wkup_pdis>;
+ };
+ };
+ };
+
+ /* Settings for all MMC/SD/SDIO default and sleep states */
+ sdi0 {
+ /* This is the external SD card slot, 4 bits wide */
+ sdi0_default_mode: sdi0_default {
+ default_mux {
+ ste,function = "mc0";
+ ste,pins = "mc0_a_1";
+ };
+ default_cfg1 {
+ ste,pins =
+ "GPIO18_AC2", /* CMDDIR */
+ "GPIO19_AC1", /* DAT0DIR */
+ "GPIO20_AB4"; /* DAT2DIR */
+ ste,config = <&out_hi>;
+ };
+ default_cfg2 {
+ ste,pins = "GPIO22_AA3"; /* FBCLK */
+ ste,config = <&in_nopull>;
+ };
+ default_cfg3 {
+ ste,pins = "GPIO23_AA4"; /* CLK */
+ ste,config = <&out_lo>;
+ };
+ default_cfg4 {
+ ste,pins =
+ "GPIO24_AB2", /* CMD */
+ "GPIO25_Y4", /* DAT0 */
+ "GPIO26_Y2", /* DAT1 */
+ "GPIO27_AA2", /* DAT2 */
+ "GPIO28_AA1"; /* DAT3 */
+ ste,config = <&in_pu>;
+ };
+ };
+
+ sdi0_sleep_mode: sdi0_sleep {
+ sleep_cfg1 {
+ ste,pins =
+ "GPIO18_AC2", /* CMDDIR */
+ "GPIO19_AC1", /* DAT0DIR */
+ "GPIO20_AB4"; /* DAT2DIR */
+ ste,config = <&slpm_out_hi_wkup_pdis>;
+ };
+ sleep_cfg2 {
+ ste,pins =
+ "GPIO22_AA3", /* FBCLK */
+ "GPIO24_AB2", /* CMD */
+ "GPIO25_Y4", /* DAT0 */
+ "GPIO26_Y2", /* DAT1 */
+ "GPIO27_AA2", /* DAT2 */
+ "GPIO28_AA1"; /* DAT3 */
+ ste,config = <&slpm_in_wkup_pdis>;
+ };
+ sleep_cfg3 {
+ ste,pins = "GPIO23_AA4"; /* CLK */
+ ste,config = <&slpm_out_lo_wkup_pdis>;
+ };
+ };
+ };
+
+ sdi1 {
+ /* This is the WLAN SDIO 4 bits wide */
+ sdi1_default_mode: sdi1_default {
+ default_mux {
+ ste,function = "mc1";
+ ste,pins = "mc1_a_1";
+ };
+ default_cfg1 {
+ ste,pins = "GPIO208_AH16"; /* CLK */
+ ste,config = <&out_lo>;
+ };
+ default_cfg2 {
+ ste,pins = "GPIO209_AG15"; /* FBCLK */
+ ste,config = <&in_nopull>;
+ };
+ default_cfg3 {
+ ste,pins =
+ "GPIO210_AJ15", /* CMD */
+ "GPIO211_AG14", /* DAT0 */
+ "GPIO212_AF13", /* DAT1 */
+ "GPIO213_AG13", /* DAT2 */
+ "GPIO214_AH15"; /* DAT3 */
+ ste,config = <&in_pu>;
+ };
+ };
+
+ sdi1_sleep_mode: sdi1_sleep {
+ sleep_cfg1 {
+ ste,pins = "GPIO208_AH16"; /* CLK */
+ ste,config = <&slpm_out_lo_wkup_pdis>;
+ };
+ sleep_cfg2 {
+ ste,pins =
+ "GPIO209_AG15", /* FBCLK */
+ "GPIO210_AJ15", /* CMD */
+ "GPIO211_AG14", /* DAT0 */
+ "GPIO212_AF13", /* DAT1 */
+ "GPIO213_AG13", /* DAT2 */
+ "GPIO214_AH15"; /* DAT3 */
+ ste,config = <&slpm_in_wkup_pdis>;
+ };
+ };
+ };
+
+ sdi2 {
+ /* This is the eMMC 8 bits wide, usually PoP eMMC */
+ sdi2_default_mode: sdi2_default {
+ default_mux {
+ ste,function = "mc2";
+ ste,pins = "mc2_a_1";
+ };
+ default_cfg1 {
+ ste,pins = "GPIO128_A5"; /* CLK */
+ ste,config = <&out_lo>;
+ };
+ default_cfg2 {
+ ste,pins = "GPIO130_C8"; /* FBCLK */
+ ste,config = <&in_nopull>;
+ };
+ default_cfg3 {
+ ste,pins =
+ "GPIO129_B4", /* CMD */
+ "GPIO131_A12", /* DAT0 */
+ "GPIO132_C10", /* DAT1 */
+ "GPIO133_B10", /* DAT2 */
+ "GPIO134_B9", /* DAT3 */
+ "GPIO135_A9", /* DAT4 */
+ "GPIO136_C7", /* DAT5 */
+ "GPIO137_A7", /* DAT6 */
+ "GPIO138_C5"; /* DAT7 */
+ ste,config = <&in_pu>;
+ };
+ };
+
+ sdi2_sleep_mode: sdi2_sleep {
+ sleep_cfg1 {
+ ste,pins = "GPIO128_A5"; /* CLK */
+ ste,config = <&out_lo_wkup_pdis>;
+ };
+ sleep_cfg2 {
+ ste,pins =
+ "GPIO130_C8", /* FBCLK */
+ "GPIO129_B4"; /* CMD */
+ ste,config = <&in_wkup_pdis_en>;
+ };
+ sleep_cfg3 {
+ ste,pins =
+ "GPIO131_A12", /* DAT0 */
+ "GPIO132_C10", /* DAT1 */
+ "GPIO133_B10", /* DAT2 */
+ "GPIO134_B9", /* DAT3 */
+ "GPIO135_A9", /* DAT4 */
+ "GPIO136_C7", /* DAT5 */
+ "GPIO137_A7", /* DAT6 */
+ "GPIO138_C5"; /* DAT7 */
+ ste,config = <&in_wkup_pdis>;
+ };
+ };
+ };
+
+ sdi4 {
+ /* This is the eMMC 8 bits wide, usually PCB-mounted eMMC */
+ sdi4_default_mode: sdi4_default {
+ default_mux {
+ ste,function = "mc4";
+ ste,pins = "mc4_a_1";
+ };
+ default_cfg1 {
+ ste,pins = "GPIO203_AE23"; /* CLK */
+ ste,config = <&out_lo>;
+ };
+ default_cfg2 {
+ ste,pins = "GPIO202_AF25"; /* FBCLK */
+ ste,config = <&in_nopull>;
+ };
+ default_cfg3 {
+ ste,pins =
+ "GPIO201_AF24", /* CMD */
+ "GPIO200_AH26", /* DAT0 */
+ "GPIO199_AH23", /* DAT1 */
+ "GPIO198_AG25", /* DAT2 */
+ "GPIO197_AH24", /* DAT3 */
+ "GPIO207_AJ23", /* DAT4 */
+ "GPIO206_AG24", /* DAT5 */
+ "GPIO205_AG23", /* DAT6 */
+ "GPIO204_AF23"; /* DAT7 */
+ ste,config = <&in_pu>;
+ };
+ };
+
+ sdi4_sleep_mode: sdi4_sleep {
+ sleep_cfg1 {
+ ste,pins = "GPIO203_AE23"; /* CLK */
+ ste,config = <&out_lo_wkup_pdis>;
+ };
+ sleep_cfg2 {
+ ste,pins =
+ "GPIO202_AF25", /* FBCLK */
+ "GPIO201_AF24", /* CMD */
+ "GPIO200_AH26", /* DAT0 */
+ "GPIO199_AH23", /* DAT1 */
+ "GPIO198_AG25", /* DAT2 */
+ "GPIO197_AH24", /* DAT3 */
+ "GPIO207_AJ23", /* DAT4 */
+ "GPIO206_AG24", /* DAT5 */
+ "GPIO205_AG23", /* DAT6 */
+ "GPIO204_AF23"; /* DAT7 */
+ ste,config = <&slpm_in_wkup_pdis>;
+ };
+ };
+ };
+
+ /*
+ * Multi-rate serial ports (MSPs) - MSP3 output is internal and
+ * cannot be muxed onto any pins.
+ */
+ msp0 {
+ msp0_default_mode: msp0_default {
+ default_msp0_mux {
+ ste,function = "msp0";
+ ste,pins = "msp0txrx_a_1", "msp0tfstck_a_1";
+ };
+ default_msp0_cfg {
+ ste,pins =
+ "GPIO12_AC4", /* TXD */
+ "GPIO15_AC3", /* RXD */
+ "GPIO13_AF3", /* TFS */
+ "GPIO14_AE3"; /* TCK */
+ ste,config = <&in_nopull>;
+ };
+ };
+ };
+
+ msp1 {
+ msp1_default_mode: msp1_default {
+ default_mux {
+ ste,function = "msp1";
+ ste,pins = "msp1txrx_a_1", "msp1_a_1";
+ };
+ default_cfg1 {
+ ste,pins = "GPIO33_AF2";
+ ste,config = <&out_lo>;
+ };
+ default_cfg2 {
+ ste,pins =
+ "GPIO34_AE1",
+ "GPIO35_AE2",
+ "GPIO36_AG2";
+ ste,config = <&in_nopull>;
+ };
+
+ };
+ };
+
+ msp2 {
+ msp2_default_mode: msp2_default {
+ /* MSP2 usually used for HDMI audio */
+ default_mux {
+ ste,function = "msp2";
+ ste,pins = "msp2_a_1";
+ };
+ default_cfg1 {
+ ste,pins =
+ "GPIO193_AH27", /* TXD */
+ "GPIO194_AF27", /* TCK */
+ "GPIO195_AG28"; /* TFS */
+ ste,config = <&in_pd>;
+ };
+ default_cfg2 {
+ ste,pins = "GPIO196_AG26"; /* RXD */
+ ste,config = <&out_lo>;
+ };
+ };
+ };
+
+
+ musb {
+ musb_default_mode: musb_default {
+ default_mux {
+ ste,function = "usb";
+ ste,pins = "usb_a_1";
+ };
+ default_cfg1 {
+ ste,pins =
+ "GPIO256_AF28", /* NXT */
+ "GPIO258_AD29", /* XCLK */
+ "GPIO259_AC29", /* DIR */
+ "GPIO260_AD28", /* DAT7 */
+ "GPIO261_AD26", /* DAT6 */
+ "GPIO262_AE26", /* DAT5 */
+ "GPIO263_AG29", /* DAT4 */
+ "GPIO264_AE27", /* DAT3 */
+ "GPIO265_AD27", /* DAT2 */
+ "GPIO266_AC28", /* DAT1 */
+ "GPIO267_AC27"; /* DAT0 */
+ ste,config = <&in_nopull>;
+ };
+ default_cfg2 {
+ ste,pins = "GPIO257_AE29"; /* STP */
+ ste,config = <&out_hi>;
+ };
+ };
+
+ musb_sleep_mode: musb_sleep {
+ sleep_cfg1 {
+ ste,pins =
+ "GPIO256_AF28", /* NXT */
+ "GPIO258_AD29", /* XCLK */
+ "GPIO259_AC29"; /* DIR */
+ ste,config = <&slpm_wkup_pdis_en>;
+ };
+ sleep_cfg2 {
+ ste,pins = "GPIO257_AE29"; /* STP */
+ ste,config = <&slpm_out_hi_wkup_pdis>;
+ };
+ sleep_cfg3 {
+ ste,pins =
+ "GPIO260_AD28", /* DAT7 */
+ "GPIO261_AD26", /* DAT6 */
+ "GPIO262_AE26", /* DAT5 */
+ "GPIO263_AG29", /* DAT4 */
+ "GPIO264_AE27", /* DAT3 */
+ "GPIO265_AD27", /* DAT2 */
+ "GPIO266_AC28", /* DAT1 */
+ "GPIO267_AC27"; /* DAT0 */
+ ste,config = <&slpm_in_wkup_pdis_en>;
+ };
+ };
+ };
+
+ mcde {
+ lcd_default_mode: lcd_default {
+ default_mux {
+ /* Mux in VSI0 and all the data lines */
+ ste,function = "lcd";
+ ste,pins =
+ "lcdvsi0_a_1", /* VSI0 for LCD */
+ "lcd_d0_d7_a_1", /* Data lines */
+ "lcd_d8_d11_a_1", /* TV-out */
+ "lcdaclk_b_1", /* Clock line for TV-out */
+ "lcdvsi1_a_1"; /* VSI1 for HDMI */
+ };
+ default_cfg1 {
+ ste,pins =
+ "GPIO68_E1", /* VSI0 */
+ "GPIO69_E2"; /* VSI1 */
+ ste,config = <&in_pu>;
+ };
+ };
+ lcd_sleep_mode: lcd_sleep {
+ sleep_cfg1 {
+ ste,pins = "GPIO69_E2"; /* VSI1 */
+ ste,config = <&slpm_in_wkup_pdis>;
+ };
+ };
+ };
+
+ ske {
+ /* SKE keys on position 2 in an 8x8 matrix */
+ ske_kpa2_default_mode: ske_kpa2_default {
+ default_mux {
+ ste,function = "kp";
+ ste,pins = "kp_a_2";
+ };
+ default_cfg1 {
+ ste,pins =
+ "GPIO153_B17", /* I7 */
+ "GPIO154_C16", /* I6 */
+ "GPIO155_C19", /* I5 */
+ "GPIO156_C17", /* I4 */
+ "GPIO161_D21", /* I3 */
+ "GPIO162_D20", /* I2 */
+ "GPIO163_C20", /* I1 */
+ "GPIO164_B21"; /* I0 */
+ ste,config = <&in_pd>;
+ };
+ default_cfg2 {
+ ste,pins =
+ "GPIO157_A18", /* O7 */
+ "GPIO158_C18", /* O6 */
+ "GPIO159_B19", /* O5 */
+ "GPIO160_B20", /* O4 */
+ "GPIO165_C21", /* O3 */
+ "GPIO166_A22", /* O2 */
+ "GPIO167_B24", /* O1 */
+ "GPIO168_C22"; /* O0 */
+ ste,config = <&out_lo>;
+ };
+ };
+ ske_kpa2_sleep_mode: ske_kpa2_sleep {
+ sleep_cfg1 {
+ ste,pins =
+ "GPIO153_B17", /* I7 */
+ "GPIO154_C16", /* I6 */
+ "GPIO155_C19", /* I5 */
+ "GPIO156_C17", /* I4 */
+ "GPIO161_D21", /* I3 */
+ "GPIO162_D20", /* I2 */
+ "GPIO163_C20", /* I1 */
+ "GPIO164_B21"; /* I0 */
+ ste,config = <&slpm_in_pu_wkup_pdis_en>;
+ };
+ sleep_cfg2 {
+ ste,pins =
+ "GPIO157_A18", /* O7 */
+ "GPIO158_C18", /* O6 */
+ "GPIO159_B19", /* O5 */
+ "GPIO160_B20", /* O4 */
+ "GPIO165_C21", /* O3 */
+ "GPIO166_A22", /* O2 */
+ "GPIO167_B24", /* O1 */
+ "GPIO168_C22"; /* O0 */
+ ste,config = <&slpm_out_lo_pdis>;
+ };
+ };
+ /*
+ * SKE keys on position 1 and "other C1" combi giving
+ * six rows of six keys.
+ */
+ ske_kpaoc1_default_mode: ske_kpaoc1_default {
+ default_mux {
+ ste,function = "kp";
+ ste,pins = "kp_a_1", "kp_oc1_1";
+ };
+ default_cfg1 {
+ ste,pins =
+ "GPIO91_B6", /* KP_O0 */
+ "GPIO90_A3", /* KP_O1 */
+ "GPIO87_B3", /* KP_O2 */
+ "GPIO86_C6", /* KP_O3 */
+ "GPIO96_D8", /* KP_O6 */
+ "GPIO94_D7"; /* KP_O7 */
+ ste,config = <&out_lo>;
+ };
+ default_cfg2 {
+ ste,pins =
+ "GPIO93_B7", /* KP_I0 */
+ "GPIO92_D6", /* KP_I1 */
+ "GPIO89_E6", /* KP_I2 */
+ "GPIO88_C4", /* KP_I3 */
+ "GPIO97_D9", /* KP_I6 */
+ "GPIO95_E8"; /* KP_I7 */
+ ste,config = <&in_pu>;
+ };
+ };
+ };
+
+ wlan {
+ wlan_default_mode: wlan_default {
+ /*
+ * Activate this mode with the WLAN chip.
+ * These are plain GPIO pins used by WLAN
+ */
+ default_cfg1 {
+ ste,pins =
+ "GPIO226_AF8", /* WLAN_PMU_EN */
+ "GPIO85_D5"; /* WLAN_ENA */
+ ste,config = <&gpio_out_lo>;
+ };
+ default_cfg2 {
+ ste,pins = "GPIO4_AH6"; /* WLAN_IRQ on UART1 */
+ ste,config = <&gpio_in_pu>;
+ };
+ };
+ };
+ };
+ };
+};
#include <dt-bindings/interrupt-controller/irq.h>
/ {
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ vdd-supply = <&ab8500_ldo_aux1_reg>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&prox_stuib_mode>, <&hall_stuib_mode>;
+
+ button@139 {
+ /* Proximity sensor */
+ gpios = <&gpio6 25 0x4>;
+ linux,code = <11>; /* SW_FRONT_PROXIMITY */
+ label = "SFH7741 Proximity Sensor";
+ };
+ button@145 {
+ /* Hall sensor */
+ gpios = <&gpio4 17 0x4>;
+ linux,code = <0>; /* SW_LID */
+ label = "HED54XXU11 Hall Effect Sensor";
+ };
+ };
+
soc {
i2c@80004000 {
stmpe1601: stmpe1601@40 {
rohm,flip-y;
};
};
+
+ pinctrl {
+ prox {
+ prox_stuib_mode: prox_stuib {
+ stuib_cfg {
+ ste,pins = "GPIO217_AH12";
+ ste,config = <&gpio_in_pu>;
+ };
+ };
+ };
+ hall {
+ hall_stuib_mode: stuib_tvk {
+ stuib_cfg {
+ ste,pins = "GPIO145_C13";
+ ste,config = <&gpio_in_pu>;
+ };
+ };
+ };
+ };
};
};
#include <dt-bindings/interrupt-controller/irq.h>
/ {
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ vdd-supply = <&ab8500_ldo_aux1_reg>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&prox_tvk_mode>, <&hall_tvk_mode>;
+
+ button@139 {
+ /* Proximity sensor */
+ gpios = <&gpio6 25 0x4>;
+ linux,code = <11>; /* SW_FRONT_PROXIMITY */
+ label = "SFH7741 Proximity Sensor";
+ };
+ button@145 {
+ /* Hall sensor */
+ gpios = <&gpio4 17 0x4>;
+ linux,code = <0>; /* SW_LID */
+ label = "HED54XXU11 Hall Effect Sensor";
+ };
+ };
+
soc {
- /* Add Synaptics touch screen, TC35892 keypad etc here */
+ /* Add Synaptics touch screen, TC35893 keypad etc here */
i2c@80004000 {
- tc3589x@44 {
- compatible = "tc3589x";
+ tc35893@44 {
+ compatible = "toshiba,tc35893";
reg = <0x44>;
interrupt-parent = <&gpio6>;
interrupts = <26 IRQ_TYPE_EDGE_RISING>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&tc35893_tvk_mode>;
interrupt-controller;
- #interrupt-cells = <2>;
+ #interrupt-cells = <1>;
tc3589x_gpio {
- compatible = "tc3589x-gpio";
- interrupts = <0 IRQ_TYPE_EDGE_RISING>;
+ compatible = "toshiba,tc3589x-gpio";
+ interrupts = <0>;
interrupt-controller;
#interrupt-cells = <2>;
gpio-controller;
#gpio-cells = <2>;
};
+ tc3589x_keypad {
+ compatible = "toshiba,tc3589x-keypad";
+ interrupts = <6>;
+ debounce-delay-ms = <4>;
+ keypad,num-columns = <8>;
+ keypad,num-rows = <8>;
+ linux,no-autorepeat;
+ linux,wakeup;
+ linux,keymap = <0x0301006b
+ 0x04010066
+ 0x06040072
+ 0x040200d7
+ 0x0303006a
+ 0x0205000e
+ 0x0607008b
+ 0x0500001c
+ 0x0403000b
+ 0x03040034
+ 0x05020067
+ 0x0305006c
+ 0x040500e7
+ 0x0005009e
+ 0x06020073
+ 0x01030039
+ 0x07060069
+ 0x050500d9>;
+ };
+ };
+ };
+ pinctrl {
+ /* Pull up this GPIO pin */
+ tc35893 {
+ tc35893_tvk_mode: tc35893_tvk {
+ tvk_cfg {
+ ste,pins = "GPIO218_AH11";
+ ste,config = <&gpio_in_pu>;
+ };
+ };
+ };
+ prox {
+ prox_tvk_mode: prox_tvk {
+ tvk_cfg {
+ ste,pins = "GPIO217_AH12";
+ ste,config = <&gpio_in_pu>;
+ };
+ };
+ };
+ hall {
+ hall_tvk_mode: hall_tvk {
+ tvk_cfg {
+ ste,pins = "GPIO145_C13";
+ ste,config = <&gpio_in_pu>;
+ };
+ };
};
};
};
#include <dt-bindings/interrupt-controller/irq.h>
#include "ste-dbx5x0.dtsi"
+#include "ste-href-family-pinctrl.dtsi"
/ {
memory {
reg = <0x00000000 0x20000000>;
};
- gpio_keys {
- compatible = "gpio-keys";
- #address-cells = <1>;
- #size-cells = <0>;
-
- button@1 {
- linux,code = <11>;
- label = "SFH7741 Proximity Sensor";
+ soc {
+ usb_per5@a03e0000 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&musb_default_mode>;
+ pinctrl-1 = <&musb_sleep_mode>;
};
- };
- soc {
uart@80120000 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&uart0_default_mode>;
+ pinctrl-1 = <&uart0_sleep_mode>;
status = "okay";
};
uart@80121000 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&uart1_default_mode>;
+ pinctrl-1 = <&uart1_sleep_mode>;
status = "okay";
};
uart@80007000 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&uart2_default_mode>;
+ pinctrl-1 = <&uart2_sleep_mode>;
status = "okay";
};
+ i2c@80004000 {
+ pinctrl-names = "default","sleep";
+ pinctrl-0 = <&i2c0_default_mode>;
+ pinctrl-1 = <&i2c0_sleep_mode>;
+ };
+
+ i2c@80122000 {
+ pinctrl-names = "default","sleep";
+ pinctrl-0 = <&i2c1_default_mode>;
+ pinctrl-1 = <&i2c1_sleep_mode>;
+ };
+
i2c@80128000 {
+ pinctrl-names = "default","sleep";
+ pinctrl-0 = <&i2c2_default_mode>;
+ pinctrl-1 = <&i2c2_sleep_mode>;
lp5521@33 {
compatible = "national,lp5521";
reg = <0x33>;
};
};
+ i2c@80110000 {
+ pinctrl-names = "default","sleep";
+ pinctrl-0 = <&i2c3_default_mode>;
+ pinctrl-1 = <&i2c3_sleep_mode>;
+ };
+
// External Micro SD slot
sdi0_per1@80126000 {
arm,primecell-periphid = <0x10480180>;
mmc-cap-mmc-highspeed;
vmmc-supply = <&ab8500_ldo_aux3_reg>;
vqmmc-supply = <&vmmci>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdi0_default_mode>;
+ pinctrl-1 = <&sdi0_sleep_mode>;
cd-gpios = <&tc3589x_gpio 3 0x4>;
arm,primecell-periphid = <0x10480180>;
max-frequency = <100000000>;
bus-width = <4>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdi1_default_mode>;
+ pinctrl-1 = <&sdi1_sleep_mode>;
status = "okay";
};
max-frequency = <100000000>;
bus-width = <8>;
mmc-cap-mmc-highspeed;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdi2_default_mode>;
+ pinctrl-1 = <&sdi2_sleep_mode>;
status = "okay";
};
bus-width = <8>;
mmc-cap-mmc-highspeed;
vmmc-supply = <&ab8500_ldo_aux2_reg>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdi4_default_mode>;
+ pinctrl-1 = <&sdi4_sleep_mode>;
status = "okay";
};
stericsson,audio-codec = <&codec>;
};
+ msp0: msp@80123000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&msp0_default_mode>;
+ status = "okay";
+ };
+
msp1: msp@80124000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&msp1_default_mode>;
+ status = "okay";
+ };
+
+ msp2: msp@80117000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&msp2_default_mode>;
status = "okay";
};
};
};
};
+
+ mcde@a0350000 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&lcd_default_mode>;
+ pinctrl-1 = <&lcd_sleep_mode>;
+ };
};
};
reg = <0x33>;
};
- tc3589x@42 {
- compatible = "tc3589x";
+ tc35892@42 {
+ compatible = "toshiba,tc35892";
reg = <0x42>;
interrupt-parent = <&gpio6>;
interrupts = <25 IRQ_TYPE_EDGE_RISING>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&tc35892_hrefprev60_mode>;
interrupt-controller;
- #interrupt-cells = <2>;
+ #interrupt-cells = <1>;
tc3589x_gpio: tc3589x_gpio {
compatible = "tc3589x-gpio";
- interrupts = <0 IRQ_TYPE_EDGE_RISING>;
+ interrupts = <0>;
interrupt-controller;
#interrupt-cells = <2>;
};
};
+ ssp@80002000 {
+ /*
+ * On the first generation boards, this SSP/SPI port was connected
+ * to the AB8500.
+ */
+ pinctrl-names = "default";
+ pinctrl-0 = <&ssp0_hrefprev60_mode>;
+ };
+
vmmci: regulator-gpio {
gpios = <&tc3589x_gpio 18 0x4>;
enable-gpio = <&tc3589x_gpio 17 0x4>;
status = "okay";
};
+
+ pinctrl {
+ /* Set this up using hogs */
+ pinctrl-names = "default";
+ pinctrl-0 = <&ipgpio_hrefprev60_mode>;
+
+ ssp0 {
+ ssp0_hrefprev60_mode: ssp0_hrefprev60_default {
+ hrefprev60_mux {
+ ste,function = "ssp0";
+ ste,pins = "ssp0_a_1";
+ };
+ hrefprev60_cfg1 {
+ ste,pins = "GPIO145_C13"; /* RXD */
+ ste,config = <&in_pd>;
+ };
+
+ };
+ };
+ sdi0 {
+ /* This additional pin needed on early MOP500 and HREFs previous to v60 */
+ sdi0_default_mode: sdi0_default {
+ hrefprev60_mux {
+ ste,function = "mc0";
+ ste,pins = "mc0dat31dir_a_1";
+ };
+ hrefprev60_cfg1 {
+ ste,pins = "GPIO21_AB3"; /* DAT31DIR */
+ ste,config = <&out_hi>;
+ };
+
+ };
+ };
+ tc35892 {
+ tc35892_hrefprev60_mode: tc35892_hrefprev60 {
+ hrefprev60_cfg {
+ ste,pins = "GPIO217_AH12";
+ ste,config = <&gpio_in_pu>;
+ };
+ };
+ };
+ ipgpio {
+ ipgpio_hrefprev60_mode: ipgpio_hrefprev60 {
+ hrefprev60_mux {
+ ste,function = "ipgpio";
+ ste,pins = "ipgpio0_c_1", "ipgpio1_c_1";
+ };
+ hrefprev60_cfg1 {
+ ste,pins = "GPIO6_AF6", "GPIO7_AG5";
+ ste,config = <&in_pu>;
+ };
+ };
+ };
+ };
};
};
model = "ST-Ericsson HREF (v60+) platform with Device Tree";
compatible = "st-ericsson,hrefv60+", "st-ericsson,u8500";
- gpio_keys {
- button@1 {
- gpios = <&gpio5 25 0x4>;
- };
- };
-
soc {
// External Micro SD slot
sdi0_per1@80126000 {
status = "okay";
};
+
+ pinctrl {
+ /*
+ * Set this up using hogs, as time goes by and as seems fit, these
+ * can be moved over to being controlled by respective device.
+ */
+ pinctrl-names = "default";
+ pinctrl-0 = <&ipgpio_hrefv60_mode>,
+ <&accel_hrefv60_mode>,
+ <&magneto_hrefv60_mode>,
+ <&etm_hrefv60_mode>,
+ <&nahj_hrefv60_mode>,
+ <&nfc_hrefv60_mode>,
+ <&force_hrefv60_mode>,
+ <&dipro_hrefv60_mode>,
+ <&vaudio_hf_hrefv60_mode>,
+ <&gbf_hrefv60_mode>,
+ <&hdtv_hrefv60_mode>,
+ <&touch_hrefv60_mode>;
+
+ sdi0 {
+ /* SD card detect GPIO pin, extend default state */
+ sdi0_default_mode: sdi0_default {
+ default_hrefv60_cfg1 {
+ ste,pins = "GPIO95_E8";
+ ste,config = <&gpio_in_pu>;
+ };
+ };
+ };
+ ipgpio {
+ /*
+ * XENON Flashgun on image processor GPIO (controlled from image
+ * processor firmware), mux in these image processor GPIO lines 0
+ * (XENON_FLASH_ID), 1 (XENON_READY) and there is an assistant
+ * LED on IP GPIO 4 (XENON_EN2) on altfunction C, that need bias
+ * from GPIO21 so pull up 0, 1 and drive 4 and GPIO21 low as output.
+ */
+ ipgpio_hrefv60_mode: ipgpio_hrefv60 {
+ hrefv60_mux {
+ ste,function = "ipgpio";
+ ste,pins = "ipgpio0_c_1", "ipgpio1_c_1", "ipgpio4_c_1";
+ };
+ hrefv60_cfg1 {
+ ste,pins = "GPIO6_AF6", "GPIO7_AG5";
+ ste,config = <&in_pu>;
+ };
+ hrefv60_cfg2 {
+ ste,pins = "GPIO21_AB3";
+ ste,config = <&gpio_out_lo>;
+ };
+ hrefv60_cfg3 {
+ ste,pins = "GPIO64_F3";
+ ste,config = <&out_lo>;
+ };
+ };
+ };
+ accelerometer {
+ accel_hrefv60_mode: accel_hrefv60 {
+ /* Accelerometer interrupt lines 1 & 2 */
+ hrefv60_cfg1 {
+ ste,pins = "GPIO82_C1", "GPIO83_D3";
+ ste,config = <&gpio_in_pu>;
+ };
+ };
+ };
+ magnetometer {
+ magneto_hrefv60_mode: magneto_hrefv60 {
+ /* Magnetometer uses GPIO 31 and 32, pull these up/down respectively */
+ hrefv60_cfg1 {
+ ste,pins = "GPIO31_V3";
+ ste,config = <&gpio_in_pu>;
+ };
+ hrefv60_cfg2 {
+ ste,pins = "GPIO32_V2";
+ ste,config = <&gpio_in_pd>;
+ };
+ };
+ };
+ etm {
+ /*
+ * Drive D19-D23 for the ETM PTM trace interface low,
+ * (presumably pins are unconnected therefore grounded here,
+ * the "other alt C1" setting enables these pins)
+ */
+ etm_hrefv60_mode: etm_hrefv60 {
+ hrefv60_cfg1 {
+ ste,pins =
+ "GPIO70_G5",
+ "GPIO71_G4",
+ "GPIO72_H4",
+ "GPIO73_H3",
+ "GPIO74_J3";
+ ste,config = <&gpio_out_lo>;
+ };
+ };
+ };
+ nahj {
+ nahj_hrefv60_mode: nahj_hrefv60 {
+ /* NAHJ CTRL on GPIO76 to low, CTRL_INV on GPIO216 to high */
+ hrefv60_cfg1 {
+ ste,pins = "GPIO76_J2";
+ ste,config = <&gpio_out_lo>;
+ };
+ hrefv60_cfg2 {
+ ste,pins = "GPIO216_AG12";
+ ste,config = <&gpio_out_hi>;
+ };
+ };
+ };
+ nfc {
+ nfc_hrefv60_mode: nfc_hrefv60 {
+ /* NFC ENA and RESET to low, pulldown IRQ line */
+ hrefv60_cfg1 {
+ ste,pins =
+ "GPIO77_H1", /* NFC_ENA */
+ "GPIO142_C11"; /* NFC_RESET */
+ ste,config = <&gpio_out_lo>;
+ };
+ hrefv60_cfg2 {
+ ste,pins = "GPIO144_B13"; /* NFC_IRQ */
+ ste,config = <&gpio_in_pd>;
+ };
+ };
+ };
+ force {
+ force_hrefv60_mode: force_hrefv60 {
+ hrefv60_cfg1 {
+ ste,pins = "GPIO91_B6"; /* FORCE_SENSING_INT */
+ ste,config = <&gpio_in_pu>;
+ };
+ hrefv60_cfg2 {
+ ste,pins =
+ "GPIO92_D6", /* FORCE_SENSING_RST */
+ "GPIO97_D9"; /* FORCE_SENSING_WU */
+ ste,config = <&gpio_out_lo>;
+ };
+ };
+ };
+ dipro {
+ dipro_hrefv60_mode: dipro_hrefv60 {
+ hrefv60_cfg1 {
+ ste,pins = "GPIO139_C9"; /* DIPRO_INT */
+ ste,config = <&gpio_in_pu>;
+ };
+ };
+ };
+ vaudio_hf {
+ vaudio_hf_hrefv60_mode: vaudio_hf_hrefv60 {
+ /* Audio Amplifier HF enable GPIO */
+ hrefv60_cfg1 {
+ ste,pins = "GPIO149_B14"; /* VAUDIO_HF_EN, enable MAX8968 */
+ ste,config = <&gpio_out_hi>;
+ };
+ };
+ };
+ gbf {
+ gbf_hrefv60_mode: gbf_hrefv60 {
+ /*
+ * GBF (GPS, Bluetooth, FM-radio) interface,
+ * pull low to reset state
+ */
+ hrefv60_cfg1 {
+ ste,pins = "GPIO171_D23"; /* GBF_ENA_RESET */
+ ste,config = <&gpio_out_lo>;
+ };
+ };
+ };
+ hdtv {
+ hdtv_hrefv60_mode: hdtv_hrefv60 {
+ /* MSP : HDTV INTERFACE GPIO line */
+ hrefv60_cfg1 {
+ ste,pins = "GPIO192_AJ27";
+ ste,config = <&gpio_in_pd>;
+ };
+ };
+ };
+ touch {
+ touch_hrefv60_mode: touch_hrefv60 {
+ /*
+ * Touch screen uses GPIO 143 for RST1, GPIO 146 for RST2 and
+ * GPIO 67 for interrupts. Pull-up the IRQ line and drive both
+ * reset signals low.
+ */
+ hrefv60_cfg1 {
+ ste,pins = "GPIO143_D12", "GPIO146_D13";
+ ste,config = <&gpio_out_lo>;
+ };
+ hrefv60_cfg2 {
+ ste,pins = "GPIO67_G2";
+ ste,config = <&gpio_in_pu>;
+ };
+ };
+ };
+ mcde {
+ lcd_hrefv60_mode: lcd_hrefv60 {
+ /*
+ * Display Interface 1 uses GPIO 65 for RST (reset).
+ * Display Interface 2 uses GPIO 66 for RST (reset).
+ * Drive DISP1 reset high (not reset), driver DISP2 reset low (reset)
+ */
+ hrefv60_cfg1 {
+ ste,pins ="GPIO65_F1";
+ ste,config = <&gpio_out_hi>;
+ };
+ hrefv60_cfg2 {
+ ste,pins ="GPIO66_G3";
+ ste,config = <&gpio_out_lo>;
+ };
+ };
+ };
+ };
};
};
ste,output = <OUTPUT_LOW>;
};
+ gpio_in_pu: gpio_input_pull_up {
+ ste,gpio = <GPIOMODE_ENABLED>;
+ ste,input = <INPUT_PULLUP>;
+ };
+
+ gpio_in_pd: gpio_input_pull_down {
+ ste,gpio = <GPIOMODE_ENABLED>;
+ ste,input = <INPUT_PULLDOWN>;
+ };
+
gpio_out_lo: gpio_output_low {
ste,gpio = <GPIOMODE_ENABLED>;
ste,output = <OUTPUT_LOW>;
};
+ gpio_out_hi: gpio_output_high {
+ ste,gpio = <GPIOMODE_ENABLED>;
+ ste,output = <OUTPUT_HIGH>;
+ };
+
+ slpm_pdis: slpm_pdis {
+ ste,sleep = <SLPM_ENABLED>;
+ ste,sleep-wakeup = <SLPM_WAKEUP_DISABLE>;
+ ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
+ };
+
+ slpm_wkup_pdis: slpm_wkup_pdis {
+ ste,sleep = <SLPM_ENABLED>;
+ ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
+ ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
+ };
+
+ slpm_wkup_pdis_en: slpm_wkup_pdis_en {
+ ste,sleep = <SLPM_ENABLED>;
+ ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
+ ste,sleep-pull-disable = <SLPM_PDIS_ENABLED>;
+ };
+
slpm_in_pu: slpm_in_pu {
ste,sleep = <SLPM_ENABLED>;
ste,sleep-input = <SLPM_INPUT_PULLUP>;
ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
};
+ slpm_in_pdis: slpm_in_pdis {
+ ste,sleep = <SLPM_ENABLED>;
+ ste,sleep-input = <SLPM_DIR_INPUT>;
+ ste,sleep-wakeup = <SLPM_WAKEUP_DISABLE>;
+ ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
+ };
+
slpm_in_wkup_pdis: slpm_in_wkup_pdis {
ste,sleep = <SLPM_ENABLED>;
ste,sleep-input = <SLPM_DIR_INPUT>;
ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
};
+ slpm_in_wkup_pdis_en: slpm_in_wkup_pdis_en {
+ ste,sleep = <SLPM_ENABLED>;
+ ste,sleep-input = <SLPM_DIR_INPUT>;
+ ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
+ ste,sleep-pull-disable = <SLPM_PDIS_ENABLED>;
+ };
+
+ slpm_in_pu_wkup_pdis_en: slpm_in_wkup_pdis_en {
+ ste,sleep = <SLPM_ENABLED>;
+ ste,sleep-input = <SLPM_INPUT_PULLUP>;
+ ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
+ ste,sleep-pull-disable = <SLPM_PDIS_ENABLED>;
+ };
+
slpm_out_lo: slpm_out_lo {
ste,sleep = <SLPM_ENABLED>;
ste,sleep-output = <SLPM_OUTPUT_LOW>;
ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
};
+ slpm_out_lo_pdis: slpm_out_lo_pdis {
+ ste,sleep = <SLPM_ENABLED>;
+ ste,sleep-output = <SLPM_OUTPUT_LOW>;
+ ste,sleep-wakeup = <SLPM_WAKEUP_DISABLE>;
+ ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
+ };
+
+ slpm_out_lo_wkup_pdis: slpm_out_lo_wkup_pdis {
+ ste,sleep = <SLPM_ENABLED>;
+ ste,sleep-output = <SLPM_OUTPUT_LOW>;
+ ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
+ ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
+ };
+
slpm_out_wkup_pdis: slpm_out_wkup_pdis {
ste,sleep = <SLPM_ENABLED>;
ste,sleep-output = <SLPM_DIR_OUTPUT>;
ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
};
+ in_wkup_pdis_en: in_wkup_pdis_en {
+ ste,sleep-input = <SLPM_DIR_INPUT>;
+ ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
+ ste,sleep-pull-disable = <SLPM_PDIS_ENABLED>;
+ };
+
+ out_lo_wkup_pdis: out_lo_wkup_pdis {
+ ste,sleep-output = <SLPM_OUTPUT_LOW>;
+ ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
+ ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
+ };
+
out_hi_wkup_pdis: out_hi_wkup_pdis {
ste,sleep-output = <SLPM_OUTPUT_HIGH>;
ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
/dts-v1/;
#include "ste-dbx5x0.dtsi"
+#include "ste-href-family-pinctrl.dtsi"
/ {
model = "Calao Systems Snowball platform with device tree";
leds {
compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpioled_snowball_mode>;
used-led {
label = "user_led";
gpios = <&gpio4 14 0x4>;
};
soc {
+ usb_per5@a03e0000 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&musb_default_mode>;
+ pinctrl-1 = <&musb_sleep_mode>;
+ };
sound {
compatible = "stericsson,snd-soc-mop500";
stericsson,audio-codec = <&codec>;
};
+ msp0: msp@80123000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&msp0_default_mode>;
+ status = "okay";
+ };
+
msp1: msp@80124000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&msp1_default_mode>;
+ status = "okay";
+ };
+
+ msp2: msp@80117000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&msp2_default_mode>;
status = "okay";
};
interrupt-parent = <&gpio4>;
vdd33a-supply = <&en_3v3_reg>;
vddvario-supply = <&db8500_vape_reg>;
+ pinctrl-names = "default";
+ pinctrl-0 = <ð_snowball_mode>;
reg-shift = <1>;
reg-io-width = <2>;
mmc-cap-mmc-highspeed;
vmmc-supply = <&ab8500_ldo_aux3_reg>;
vqmmc-supply = <&vmmci>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdi0_default_mode>;
+ pinctrl-1 = <&sdi0_sleep_mode>;
cd-gpios = <&gpio6 26 0x4>; // 218
cd-inverted;
status = "okay";
};
+ // WLAN SDIO channel
+ sdi1_per2@80118000 {
+ arm,primecell-periphid = <0x10480180>;
+ max-frequency = <100000000>;
+ bus-width = <4>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdi1_default_mode>;
+ pinctrl-1 = <&sdi1_sleep_mode>;
+
+ status = "okay";
+ };
+
+ // Unused PoP eMMC - register and put it to sleep by default */
+ sdi2_per3@80005000 {
+ arm,primecell-periphid = <0x10480180>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdi2_sleep_mode>;
+
+ status = "okay";
+ };
+
// On-board eMMC
sdi4_per2@80114000 {
arm,primecell-periphid = <0x10480180>;
bus-width = <8>;
mmc-cap-mmc-highspeed;
vmmc-supply = <&ab8500_ldo_aux2_reg>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdi4_default_mode>;
+ pinctrl-1 = <&sdi4_sleep_mode>;
status = "okay";
};
uart@80120000 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&uart0_default_mode>;
+ pinctrl-1 = <&uart0_sleep_mode>;
status = "okay";
};
uart@80121000 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&uart1_default_mode>;
+ pinctrl-1 = <&uart1_sleep_mode>;
status = "okay";
};
uart@80007000 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&uart2_default_mode>;
+ pinctrl-1 = <&uart2_sleep_mode>;
status = "okay";
};
+ i2c@80004000 {
+ pinctrl-names = "default","sleep";
+ pinctrl-0 = <&i2c0_default_mode>;
+ pinctrl-1 = <&i2c0_sleep_mode>;
+ };
+
+ i2c@80122000 {
+ pinctrl-names = "default","sleep";
+ pinctrl-0 = <&i2c1_default_mode>;
+ pinctrl-1 = <&i2c1_sleep_mode>;
+ };
+
+ i2c@80128000 {
+ pinctrl-names = "default","sleep";
+ pinctrl-0 = <&i2c2_default_mode>;
+ pinctrl-1 = <&i2c2_sleep_mode>;
+ };
+
+ i2c@80110000 {
+ pinctrl-names = "default","sleep";
+ pinctrl-0 = <&i2c3_default_mode>;
+ pinctrl-1 = <&i2c3_sleep_mode>;
+ };
+
+ ssp@80002000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ssp0_snowball_mode>;
+ };
+
cpufreq-cooling {
status = "okay";
};
};
};
};
+
+ pinctrl {
+ /*
+ * Set this up using hogs, as time goes by and as seems fit, these
+ * can be moved over to being controlled by respective device.
+ */
+ pinctrl-names = "default";
+ pinctrl-0 = <&accel_snowball_mode>,
+ <&magneto_snowball_mode>,
+ <&gbf_snowball_mode>,
+ <&wlan_snowball_mode>;
+
+ ethernet {
+ /*
+ * Mux in "SM" which is used for the
+ * SMSC911x Ethernet adapter
+ */
+ eth_snowball_mode: eth_snowball {
+ snowball_mux {
+ ste,function = "sm";
+ ste,pins = "sm_b_1";
+ };
+ /* LAN IRQ pin */
+ snowball_cfg1 {
+ ste,pins = "GPIO140_B11";
+ ste,config = <&in_nopull>;
+ };
+ /* LAN reset pin */
+ snowball_cfg2 {
+ ste,pins = "GPIO141_C12";
+ ste,config = <&gpio_out_hi>;
+ };
+
+ };
+ };
+ sdi0 {
+ sdi0_default_mode: sdi0_default {
+ snowball_mux {
+ ste,function = "mc0";
+ ste,pins = "mc0dat31dir_a_1";
+ };
+ snowball_cfg1 {
+ ste,pins = "GPIO21_AB3"; /* DAT31DIR */
+ ste,config = <&out_hi>;
+ };
+
+ };
+ };
+ ssp0 {
+ ssp0_snowball_mode: ssp0_snowball_default {
+ snowball_mux {
+ ste,function = "ssp0";
+ ste,pins = "ssp0_a_1";
+ };
+ snowball_cfg1 {
+ ste,pins = "GPIO144_B13"; /* FRM */
+ ste,config = <&gpio_out_hi>;
+ };
+ snowball_cfg2 {
+ ste,pins = "GPIO145_C13"; /* RXD */
+ ste,config = <&in_pd>;
+ };
+ snowball_cfg3 {
+ ste,pins =
+ "GPIO146_D13", /* TXD */
+ "GPIO143_D12"; /* CLK */
+ ste,config = <&out_lo>;
+ };
+
+ };
+ };
+ gpio_led {
+ gpioled_snowball_mode: gpioled_default {
+ snowball_cfg1 {
+ ste,pins = "GPIO142_C11";
+ ste,config = <&gpio_out_hi>;
+ };
+
+ };
+ };
+ accelerometer {
+ accel_snowball_mode: accel_snowball {
+ /* Accelerometer lines */
+ snowball_cfg1 {
+ ste,pins =
+ "GPIO163_C20", /* ACCEL_IRQ1 */
+ "GPIO164_B21"; /* ACCEL_IRQ2 */
+ ste,config = <&gpio_in_pu>;
+ };
+ };
+ };
+ magnetometer {
+ magneto_snowball_mode: magneto_snowball {
+ snowball_cfg1 {
+ ste,pins = "GPIO165_C21"; /* MAG_DRDY */
+ ste,config = <&gpio_in_pu>;
+ };
+ };
+ };
+ gbf {
+ gbf_snowball_mode: gbf_snowball {
+ /*
+ * GBF (GPS, Bluetooth, FM-radio) interface,
+ * pull low to reset state
+ */
+ snowball_cfg1 {
+ ste,pins = "GPIO171_D23"; /* GBF_ENA_RESET */
+ ste,config = <&gpio_out_lo>;
+ };
+ };
+ };
+ wlan {
+ wlan_snowball_mode: wlan_snowball {
+ /*
+ * Activate this mode with the WLAN chip.
+ * These are plain GPIO pins used by WLAN
+ */
+ snowball_cfg1 {
+ ste,pins =
+ "GPIO161_D21", /* WLAN_PMU_EN */
+ "GPIO215_AH13"; /* WLAN_ENA */
+ ste,config = <&gpio_out_lo>;
+ };
+ snowball_cfg2 {
+ ste,pins = "GPIO216_AG12"; /* WLAN_IRQ */
+ ste,config = <&gpio_in_pu>;
+ };
+ };
+ };
+ };
+
+ mcde@a0350000 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&lcd_default_mode>;
+ pinctrl-1 = <&lcd_sleep_mode>;
+ };
};
};
};
};
};
+
+ sbc_i2c0 {
+ pinctrl_sbc_i2c0_default: sbc_i2c0-default {
+ st,pins {
+ sda = <&PIO4 6 ALT1 BIDIR>;
+ scl = <&PIO4 5 ALT1 BIDIR>;
+ };
+ };
+ };
+
+ sbc_i2c1 {
+ pinctrl_sbc_i2c1_default: sbc_i2c1-default {
+ st,pins {
+ sda = <&PIO3 2 ALT2 BIDIR>;
+ scl = <&PIO3 1 ALT2 BIDIR>;
+ };
+ };
+ };
};
pin-controller-front {
reg = <0x7000 0x100>;
st,bank-name = "PIO12";
};
+
+ i2c0 {
+ pinctrl_i2c0_default: i2c0-default {
+ st,pins {
+ sda = <&PIO9 3 ALT1 BIDIR>;
+ scl = <&PIO9 2 ALT1 BIDIR>;
+ };
+ };
+ };
+
+ i2c1 {
+ pinctrl_i2c1_default: i2c1-default {
+ st,pins {
+ sda = <&PIO12 1 ALT1 BIDIR>;
+ scl = <&PIO12 0 ALT1 BIDIR>;
+ };
+ };
+ };
};
pin-controller-rear {
#include "stih41x.dtsi"
#include "stih415-clock.dtsi"
#include "stih415-pinctrl.dtsi"
+#include <dt-bindings/interrupt-controller/arm-gic.h>
/ {
L2: cache-controller {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_sbc_serial1>;
};
+
+ i2c@fed40000 {
+ compatible = "st,comms-ssc4-i2c";
+ reg = <0xfed40000 0x110>;
+ interrupts = <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&CLKS_ICN_REG_0>;
+ clock-names = "ssc";
+ clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c0_default>;
+
+ status = "disabled";
+ };
+
+ i2c@fed41000 {
+ compatible = "st,comms-ssc4-i2c";
+ reg = <0xfed41000 0x110>;
+ interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&CLKS_ICN_REG_0>;
+ clock-names = "ssc";
+ clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1_default>;
+
+ status = "disabled";
+ };
+
+ i2c@fe540000 {
+ compatible = "st,comms-ssc4-i2c";
+ reg = <0xfe540000 0x110>;
+ interrupts = <GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&CLK_SYSIN>;
+ clock-names = "ssc";
+ clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sbc_i2c0_default>;
+
+ status = "disabled";
+ };
+
+ i2c@fe541000 {
+ compatible = "st,comms-ssc4-i2c";
+ reg = <0xfe541000 0x110>;
+ interrupts = <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&CLK_SYSIN>;
+ clock-names = "ssc";
+ clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sbc_i2c1_default>;
+
+ status = "disabled";
+ };
};
};
};
};
};
+
+ sbc_i2c0 {
+ pinctrl_sbc_i2c0_default: sbc_i2c0-default {
+ st,pins {
+ sda = <&PIO4 6 ALT1 BIDIR>;
+ scl = <&PIO4 5 ALT1 BIDIR>;
+ };
+ };
+ };
+
+ sbc_i2c1 {
+ pinctrl_sbc_i2c1_default: sbc_i2c1-default {
+ st,pins {
+ sda = <&PIO3 2 ALT2 BIDIR>;
+ scl = <&PIO3 1 ALT2 BIDIR>;
+ };
+ };
+ };
};
pin-controller-front {
};
};
+ i2c0 {
+ pinctrl_i2c0_default: i2c0-default {
+ st,pins {
+ sda = <&PIO9 3 ALT1 BIDIR>;
+ scl = <&PIO9 2 ALT1 BIDIR>;
+ };
+ };
+ };
+
+ i2c1 {
+ pinctrl_i2c1_default: i2c1-default {
+ st,pins {
+ sda = <&PIO12 1 ALT1 BIDIR>;
+ scl = <&PIO12 0 ALT1 BIDIR>;
+ };
+ };
+ };
};
pin-controller-rear {
#include "stih41x.dtsi"
#include "stih416-clock.dtsi"
#include "stih416-pinctrl.dtsi"
+#include <dt-bindings/interrupt-controller/arm-gic.h>
/ {
L2: cache-controller {
compatible = "arm,pl310-cache";
pinctrl-0 = <&pinctrl_sbc_serial1>;
clocks = <&CLK_SYSIN>;
};
+
+ i2c@fed40000 {
+ compatible = "st,comms-ssc4-i2c";
+ reg = <0xfed40000 0x110>;
+ interrupts = <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&CLK_S_ICN_REG_0>;
+ clock-names = "ssc";
+ clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c0_default>;
+
+ status = "disabled";
+ };
+
+ i2c@fed41000 {
+ compatible = "st,comms-ssc4-i2c";
+ reg = <0xfed41000 0x110>;
+ interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&CLK_S_ICN_REG_0>;
+ clock-names = "ssc";
+ clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1_default>;
+
+ status = "disabled";
+ };
+
+ i2c@fe540000 {
+ compatible = "st,comms-ssc4-i2c";
+ reg = <0xfe540000 0x110>;
+ interrupts = <GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&CLK_SYSIN>;
+ clock-names = "ssc";
+ clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sbc_i2c0_default>;
+
+ status = "disabled";
+ };
+
+ i2c@fe541000 {
+ compatible = "st,comms-ssc4-i2c";
+ reg = <0xfe541000 0x110>;
+ interrupts = <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&CLK_SYSIN>;
+ clock-names = "ssc";
+ clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sbc_i2c1_default>;
+
+ status = "disabled";
+ };
};
};
};
};
+ /* HDMI Tx I2C */
+ i2c@fed41000 {
+ /* HDMI V1.3a supports Standard mode only */
+ clock-frequency = <100000>;
+ i2c-min-scl-pulse-width-us = <0>;
+ i2c-min-sda-pulse-width-us = <5>;
+
+ status = "okay";
+ };
};
};
default-state = "off";
};
};
+
+ i2c@fed40000 {
+ status = "okay";
+ };
+
+ /* HDMI Tx I2C */
+ i2c@fed41000 {
+ /* HDMI V1.3a supports Standard mode only */
+ clock-frequency = <100000>;
+ i2c-min-scl-pulse-width-us = <0>;
+ i2c-min-sda-pulse-width-us = <5>;
+
+ status = "okay";
+ };
+
+ i2c@fe540000 {
+ status = "okay";
+ };
+
+ i2c@fe541000 {
+ status = "okay";
+ };
};
};
# Makefile for the linux kernel, U8500 machine.
#
-obj-y := cpu.o devices.o id.o timer.o pm.o
+obj-y := cpu.o id.o timer.o pm.o
obj-$(CONFIG_CACHE_L2X0) += cache-l2x0.o
-obj-$(CONFIG_UX500_SOC_DB8500) += cpu-db8500.o devices-db8500.o
-obj-$(CONFIG_MACH_MOP500) += board-mop500.o board-mop500-sdi.o \
+obj-$(CONFIG_UX500_SOC_DB8500) += cpu-db8500.o
+obj-$(CONFIG_MACH_MOP500) += board-mop500-sdi.o \
board-mop500-regulators.o \
board-mop500-pins.o \
board-mop500-audio.o
#include <linux/platform_device.h>
#include <linux/init.h>
#include <linux/gpio.h>
-#include <linux/platform_data/pinctrl-nomadik.h>
#include <linux/platform_data/dma-ste-dma40.h>
-#include "devices.h"
#include "irqs.h"
#include <linux/platform_data/asoc-ux500-msp.h>
#include "ste-dma40-db8500.h"
#include "board-mop500.h"
-#include "devices-db8500.h"
static struct stedma40_chan_cfg msp0_dma_rx = {
.high_priority = true,
#include <linux/string.h>
#include <linux/pinctrl/machine.h>
#include <linux/pinctrl/pinconf-generic.h>
-#include <linux/platform_data/pinctrl-nomadik.h>
#include <asm/mach-types.h>
#include "board-mop500.h"
-enum custom_pin_cfg_t {
- PINS_FOR_DEFAULT,
- PINS_FOR_U9500,
-};
-
-static enum custom_pin_cfg_t pinsfor;
-
/* These simply sets bias for pins */
#define BIAS(a,b) static unsigned long a[] = { b }
-BIAS(pd, PIN_PULL_DOWN);
-BIAS(in_nopull, PIN_INPUT_NOPULL);
-BIAS(in_nopull_slpm_nowkup, PIN_INPUT_NOPULL|PIN_SLPM_WAKEUP_DISABLE);
-BIAS(in_pu, PIN_INPUT_PULLUP);
-BIAS(in_pd, PIN_INPUT_PULLDOWN);
-BIAS(out_hi, PIN_OUTPUT_HIGH);
-BIAS(out_lo, PIN_OUTPUT_LOW);
-BIAS(out_lo_slpm_nowkup, PIN_OUTPUT_LOW|PIN_SLPM_WAKEUP_DISABLE);
-
BIAS(abx500_out_lo, PIN_CONF_PACKED(PIN_CONFIG_OUTPUT, 0));
BIAS(abx500_in_pd, PIN_CONF_PACKED(PIN_CONFIG_BIAS_PULL_DOWN, 1));
BIAS(abx500_in_nopull, PIN_CONF_PACKED(PIN_CONFIG_BIAS_PULL_DOWN, 0));
-/* These also force them into GPIO mode */
-BIAS(gpio_in_pu, PIN_INPUT_PULLUP|PIN_GPIOMODE_ENABLED);
-BIAS(gpio_in_pd, PIN_INPUT_PULLDOWN|PIN_GPIOMODE_ENABLED);
-BIAS(gpio_in_pu_slpm_gpio_nopull, PIN_INPUT_PULLUP|PIN_GPIOMODE_ENABLED|PIN_SLPM_GPIO|PIN_SLPM_INPUT_NOPULL);
-BIAS(gpio_in_pd_slpm_gpio_nopull, PIN_INPUT_PULLDOWN|PIN_GPIOMODE_ENABLED|PIN_SLPM_GPIO|PIN_SLPM_INPUT_NOPULL);
-BIAS(gpio_out_hi, PIN_OUTPUT_HIGH|PIN_GPIOMODE_ENABLED);
-BIAS(gpio_out_lo, PIN_OUTPUT_LOW|PIN_GPIOMODE_ENABLED);
-/* Sleep modes */
-BIAS(slpm_in_wkup_pdis, PIN_SLEEPMODE_ENABLED|
- PIN_SLPM_DIR_INPUT|PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
-BIAS(slpm_in_wkup_pdis_en, PIN_SLEEPMODE_ENABLED|
- PIN_SLPM_DIR_INPUT|PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_ENABLED);
-BIAS(slpm_wkup_pdis, PIN_SLEEPMODE_ENABLED|
- PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
-BIAS(slpm_wkup_pdis_en, PIN_SLEEPMODE_ENABLED|
- PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_ENABLED);
-BIAS(slpm_out_lo_pdis, PIN_SLEEPMODE_ENABLED|
- PIN_SLPM_OUTPUT_LOW|PIN_SLPM_WAKEUP_DISABLE|PIN_SLPM_PDIS_DISABLED);
-BIAS(slpm_out_lo_wkup_pdis, PIN_SLEEPMODE_ENABLED|
- PIN_SLPM_OUTPUT_LOW|PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
-BIAS(slpm_out_hi_wkup_pdis, PIN_SLEEPMODE_ENABLED|PIN_SLPM_OUTPUT_HIGH|
- PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
-BIAS(slpm_in_nopull_wkup_pdis, PIN_SLEEPMODE_ENABLED|
- PIN_SLPM_INPUT_NOPULL|PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
-BIAS(slpm_in_pu_wkup_pdis_en, PIN_SLEEPMODE_ENABLED|PIN_SLPM_INPUT_PULLUP|
- PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_ENABLED);
-BIAS(slpm_out_wkup_pdis, PIN_SLEEPMODE_ENABLED|
- PIN_SLPM_DIR_OUTPUT|PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
-BIAS(out_lo_wkup_pdis, PIN_SLPM_OUTPUT_LOW|
- PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
-BIAS(in_wkup_pdis_en, PIN_SLPM_DIR_INPUT|PIN_SLPM_WAKEUP_ENABLE|
- PIN_SLPM_PDIS_ENABLED);
-BIAS(in_wkup_pdis, PIN_SLPM_DIR_INPUT|PIN_SLPM_WAKEUP_ENABLE|
- PIN_SLPM_PDIS_DISABLED);
-BIAS(out_wkup_pdis, PIN_SLPM_DIR_OUTPUT|PIN_SLPM_WAKEUP_ENABLE|
- PIN_SLPM_PDIS_DISABLED);
-
-/* We use these to define hog settings that are always done on boot */
-#define DB8500_MUX_HOG(group,func) \
- PIN_MAP_MUX_GROUP_HOG_DEFAULT("pinctrl-db8500", group, func)
-#define DB8500_PIN_HOG(pin,conf) \
- PIN_MAP_CONFIGS_PIN_HOG_DEFAULT("pinctrl-db8500", pin, conf)
-
-/* These are default states associated with device and changed runtime */
-#define DB8500_MUX(group,func,dev) \
- PIN_MAP_MUX_GROUP_DEFAULT(dev, "pinctrl-db8500", group, func)
-#define DB8500_PIN(pin,conf,dev) \
- PIN_MAP_CONFIGS_PIN_DEFAULT(dev, "pinctrl-db8500", pin, conf)
-#define DB8500_PIN_IDLE(pin, conf, dev) \
- PIN_MAP_CONFIGS_PIN(dev, PINCTRL_STATE_IDLE, "pinctrl-db8500", \
- pin, conf)
-#define DB8500_PIN_SLEEP(pin, conf, dev) \
- PIN_MAP_CONFIGS_PIN(dev, PINCTRL_STATE_SLEEP, "pinctrl-db8500", \
- pin, conf)
-#define DB8500_MUX_STATE(group, func, dev, state) \
- PIN_MAP_MUX_GROUP(dev, state, "pinctrl-db8500", group, func)
-#define DB8500_PIN_STATE(pin, conf, dev, state) \
- PIN_MAP_CONFIGS_PIN(dev, state, "pinctrl-db8500", pin, conf)
-
#define AB8500_MUX_HOG(group, func) \
PIN_MAP_MUX_GROUP_HOG_DEFAULT("pinctrl-ab8500.0", group, func)
#define AB8500_PIN_HOG(pin, conf) \
AB8505_PIN_HOG("GPIO53_D15", in_pd),
};
-/* Pin control settings */
-static struct pinctrl_map __initdata mop500_family_pinmap[] = {
- /*
- * uMSP0, mux in 4 pins, regular placement of RX/TX
- * explicitly set the pins to no pull
- */
- DB8500_MUX_HOG("msp0txrx_a_1", "msp0"),
- DB8500_MUX_HOG("msp0tfstck_a_1", "msp0"),
- DB8500_PIN_HOG("GPIO12_AC4", in_nopull), /* TXD */
- DB8500_PIN_HOG("GPIO15_AC3", in_nopull), /* RXD */
- DB8500_PIN_HOG("GPIO13_AF3", in_nopull), /* TFS */
- DB8500_PIN_HOG("GPIO14_AE3", in_nopull), /* TCK */
- /* MSP2 for HDMI, pull down TXD, TCK, TFS */
- DB8500_MUX_HOG("msp2_a_1", "msp2"),
- DB8500_PIN_HOG("GPIO193_AH27", in_pd), /* TXD */
- DB8500_PIN_HOG("GPIO194_AF27", in_pd), /* TCK */
- DB8500_PIN_HOG("GPIO195_AG28", in_pd), /* TFS */
- DB8500_PIN_HOG("GPIO196_AG26", out_lo), /* RXD */
- /*
- * LCD, set TE0 (using LCD VSI0) and D14 (touch screen interrupt) to
- * pull-up
- * TODO: is this really correct? Snowball doesn't have a LCD.
- */
- DB8500_MUX_HOG("lcdvsi0_a_1", "lcd"),
- DB8500_PIN_HOG("GPIO68_E1", in_pu),
- DB8500_PIN_HOG("GPIO84_C2", gpio_in_pu),
- /*
- * STMPE1601/tc35893 keypad IRQ GPIO 218
- * TODO: set for snowball and HREF really??
- */
- DB8500_PIN_HOG("GPIO218_AH11", gpio_in_pu),
- /*
- * UART0, we do not mux in u0 here.
- * uart-0 pins gpio configuration should be kept intact to prevent
- * a glitch in tx line when the tty dev is opened. Later these pins
- * are configured by uart driver
- */
- DB8500_PIN_HOG("GPIO0_AJ5", in_pu), /* CTS */
- DB8500_PIN_HOG("GPIO1_AJ3", out_hi), /* RTS */
- DB8500_PIN_HOG("GPIO2_AH4", in_pu), /* RXD */
- DB8500_PIN_HOG("GPIO3_AH3", out_hi), /* TXD */
- /*
- * Mux in UART2 on altfunction C and set pull-ups.
- * TODO: is this used on U8500 variants and Snowball really?
- * The setting on GPIO31 conflicts with magnetometer use on hrefv60
- */
- /* default state for UART2 */
- DB8500_MUX("u2rxtx_c_1", "u2", "uart2"),
- DB8500_PIN("GPIO29_W2", in_pu, "uart2"), /* RXD */
- DB8500_PIN("GPIO30_W3", out_hi, "uart2"), /* TXD */
- /* Sleep state for UART2 */
- DB8500_PIN_SLEEP("GPIO29_W2", in_wkup_pdis, "uart2"),
- DB8500_PIN_SLEEP("GPIO30_W3", out_wkup_pdis, "uart2"),
- /*
- * The following pin sets were known as "runtime pins" before being
- * converted to the pinctrl model. Here we model them as "default"
- * states.
- */
- /* Mux in UART0 after initialization */
- DB8500_MUX("u0_a_1", "u0", "uart0"),
- DB8500_PIN("GPIO0_AJ5", in_pu, "uart0"), /* CTS */
- DB8500_PIN("GPIO1_AJ3", out_hi, "uart0"), /* RTS */
- DB8500_PIN("GPIO2_AH4", in_pu, "uart0"), /* RXD */
- DB8500_PIN("GPIO3_AH3", out_hi, "uart0"), /* TXD */
- /* Sleep state for UART0 */
- DB8500_PIN_SLEEP("GPIO0_AJ5", slpm_in_wkup_pdis, "uart0"),
- DB8500_PIN_SLEEP("GPIO1_AJ3", slpm_out_hi_wkup_pdis, "uart0"),
- DB8500_PIN_SLEEP("GPIO2_AH4", slpm_in_wkup_pdis, "uart0"),
- DB8500_PIN_SLEEP("GPIO3_AH3", slpm_out_wkup_pdis, "uart0"),
- /* Mux in UART1 after initialization */
- DB8500_MUX("u1rxtx_a_1", "u1", "uart1"),
- DB8500_PIN("GPIO4_AH6", in_pu, "uart1"), /* RXD */
- DB8500_PIN("GPIO5_AG6", out_hi, "uart1"), /* TXD */
- /* Sleep state for UART1 */
- DB8500_PIN_SLEEP("GPIO4_AH6", slpm_in_wkup_pdis, "uart1"),
- DB8500_PIN_SLEEP("GPIO5_AG6", slpm_out_wkup_pdis, "uart1"),
- /* MSP1 for ALSA codec */
- DB8500_MUX_HOG("msp1txrx_a_1", "msp1"),
- DB8500_MUX_HOG("msp1_a_1", "msp1"),
- DB8500_PIN_HOG("GPIO33_AF2", out_lo_slpm_nowkup),
- DB8500_PIN_HOG("GPIO34_AE1", in_nopull_slpm_nowkup),
- DB8500_PIN_HOG("GPIO35_AE2", in_nopull_slpm_nowkup),
- DB8500_PIN_HOG("GPIO36_AG2", in_nopull_slpm_nowkup),
- /* Mux in LCD data lines 8 thru 11 and LCDA CLK for MCDE TVOUT */
- DB8500_MUX("lcd_d8_d11_a_1", "lcd", "mcde-tvout"),
- DB8500_MUX("lcdaclk_b_1", "lcda", "mcde-tvout"),
- /* Mux in LCD VSI1 and pull it up for MCDE HDMI output */
- DB8500_MUX("lcdvsi1_a_1", "lcd", "0-0070"),
- DB8500_PIN("GPIO69_E2", in_pu, "0-0070"),
- /* LCD VSI1 sleep state */
- DB8500_PIN_SLEEP("GPIO69_E2", slpm_in_wkup_pdis, "0-0070"),
- /* Mux in i2c0 block, default state */
- DB8500_MUX("i2c0_a_1", "i2c0", "nmk-i2c.0"),
- /* i2c0 sleep state */
- DB8500_PIN_SLEEP("GPIO147_C15", slpm_in_nopull_wkup_pdis, "nmk-i2c.0"), /* SDA */
- DB8500_PIN_SLEEP("GPIO148_B16", slpm_in_nopull_wkup_pdis, "nmk-i2c.0"), /* SCL */
- /* Mux in i2c1 block, default state */
- DB8500_MUX("i2c1_b_2", "i2c1", "nmk-i2c.1"),
- /* i2c1 sleep state */
- DB8500_PIN_SLEEP("GPIO16_AD3", slpm_in_nopull_wkup_pdis, "nmk-i2c.1"), /* SDA */
- DB8500_PIN_SLEEP("GPIO17_AD4", slpm_in_nopull_wkup_pdis, "nmk-i2c.1"), /* SCL */
- /* Mux in i2c2 block, default state */
- DB8500_MUX("i2c2_b_2", "i2c2", "nmk-i2c.2"),
- /* i2c2 sleep state */
- DB8500_PIN_SLEEP("GPIO10_AF5", slpm_in_nopull_wkup_pdis, "nmk-i2c.2"), /* SDA */
- DB8500_PIN_SLEEP("GPIO11_AG4", slpm_in_nopull_wkup_pdis, "nmk-i2c.2"), /* SCL */
- /* Mux in i2c3 block, default state */
- DB8500_MUX("i2c3_c_2", "i2c3", "nmk-i2c.3"),
- /* i2c3 sleep state */
- DB8500_PIN_SLEEP("GPIO229_AG7", slpm_in_nopull_wkup_pdis, "nmk-i2c.3"), /* SDA */
- DB8500_PIN_SLEEP("GPIO230_AF7", slpm_in_nopull_wkup_pdis, "nmk-i2c.3"), /* SCL */
- /* Mux in SDI0 (here called MC0) used for removable MMC/SD/SDIO cards */
- DB8500_MUX("mc0_a_1", "mc0", "sdi0"),
- DB8500_PIN("GPIO18_AC2", out_hi, "sdi0"), /* CMDDIR */
- DB8500_PIN("GPIO19_AC1", out_hi, "sdi0"), /* DAT0DIR */
- DB8500_PIN("GPIO20_AB4", out_hi, "sdi0"), /* DAT2DIR */
- DB8500_PIN("GPIO22_AA3", in_nopull, "sdi0"), /* FBCLK */
- DB8500_PIN("GPIO23_AA4", out_lo, "sdi0"), /* CLK */
- DB8500_PIN("GPIO24_AB2", in_pu, "sdi0"), /* CMD */
- DB8500_PIN("GPIO25_Y4", in_pu, "sdi0"), /* DAT0 */
- DB8500_PIN("GPIO26_Y2", in_pu, "sdi0"), /* DAT1 */
- DB8500_PIN("GPIO27_AA2", in_pu, "sdi0"), /* DAT2 */
- DB8500_PIN("GPIO28_AA1", in_pu, "sdi0"), /* DAT3 */
- /* SDI0 sleep state */
- DB8500_PIN_SLEEP("GPIO18_AC2", slpm_out_hi_wkup_pdis, "sdi0"),
- DB8500_PIN_SLEEP("GPIO19_AC1", slpm_out_hi_wkup_pdis, "sdi0"),
- DB8500_PIN_SLEEP("GPIO20_AB4", slpm_out_hi_wkup_pdis, "sdi0"),
- DB8500_PIN_SLEEP("GPIO22_AA3", slpm_in_wkup_pdis, "sdi0"),
- DB8500_PIN_SLEEP("GPIO23_AA4", slpm_out_lo_wkup_pdis, "sdi0"),
- DB8500_PIN_SLEEP("GPIO24_AB2", slpm_in_wkup_pdis, "sdi0"),
- DB8500_PIN_SLEEP("GPIO25_Y4", slpm_in_wkup_pdis, "sdi0"),
- DB8500_PIN_SLEEP("GPIO26_Y2", slpm_in_wkup_pdis, "sdi0"),
- DB8500_PIN_SLEEP("GPIO27_AA2", slpm_in_wkup_pdis, "sdi0"),
- DB8500_PIN_SLEEP("GPIO28_AA1", slpm_in_wkup_pdis, "sdi0"),
-
- /* Mux in SDI1 (here called MC1) used for SDIO for CW1200 WLAN */
- DB8500_MUX("mc1_a_1", "mc1", "sdi1"),
- DB8500_PIN("GPIO208_AH16", out_lo, "sdi1"), /* CLK */
- DB8500_PIN("GPIO209_AG15", in_nopull, "sdi1"), /* FBCLK */
- DB8500_PIN("GPIO210_AJ15", in_pu, "sdi1"), /* CMD */
- DB8500_PIN("GPIO211_AG14", in_pu, "sdi1"), /* DAT0 */
- DB8500_PIN("GPIO212_AF13", in_pu, "sdi1"), /* DAT1 */
- DB8500_PIN("GPIO213_AG13", in_pu, "sdi1"), /* DAT2 */
- DB8500_PIN("GPIO214_AH15", in_pu, "sdi1"), /* DAT3 */
- /* SDI1 sleep state */
- DB8500_PIN_SLEEP("GPIO208_AH16", slpm_out_lo_wkup_pdis, "sdi1"), /* CLK */
- DB8500_PIN_SLEEP("GPIO209_AG15", slpm_in_wkup_pdis, "sdi1"), /* FBCLK */
- DB8500_PIN_SLEEP("GPIO210_AJ15", slpm_in_wkup_pdis, "sdi1"), /* CMD */
- DB8500_PIN_SLEEP("GPIO211_AG14", slpm_in_wkup_pdis, "sdi1"), /* DAT0 */
- DB8500_PIN_SLEEP("GPIO212_AF13", slpm_in_wkup_pdis, "sdi1"), /* DAT1 */
- DB8500_PIN_SLEEP("GPIO213_AG13", slpm_in_wkup_pdis, "sdi1"), /* DAT2 */
- DB8500_PIN_SLEEP("GPIO214_AH15", slpm_in_wkup_pdis, "sdi1"), /* DAT3 */
-
- /* Mux in SDI2 (here called MC2) used for for PoP eMMC */
- DB8500_MUX("mc2_a_1", "mc2", "sdi2"),
- DB8500_PIN("GPIO128_A5", out_lo, "sdi2"), /* CLK */
- DB8500_PIN("GPIO129_B4", in_pu, "sdi2"), /* CMD */
- DB8500_PIN("GPIO130_C8", in_nopull, "sdi2"), /* FBCLK */
- DB8500_PIN("GPIO131_A12", in_pu, "sdi2"), /* DAT0 */
- DB8500_PIN("GPIO132_C10", in_pu, "sdi2"), /* DAT1 */
- DB8500_PIN("GPIO133_B10", in_pu, "sdi2"), /* DAT2 */
- DB8500_PIN("GPIO134_B9", in_pu, "sdi2"), /* DAT3 */
- DB8500_PIN("GPIO135_A9", in_pu, "sdi2"), /* DAT4 */
- DB8500_PIN("GPIO136_C7", in_pu, "sdi2"), /* DAT5 */
- DB8500_PIN("GPIO137_A7", in_pu, "sdi2"), /* DAT6 */
- DB8500_PIN("GPIO138_C5", in_pu, "sdi2"), /* DAT7 */
- /* SDI2 sleep state */
- DB8500_PIN_SLEEP("GPIO128_A5", out_lo_wkup_pdis, "sdi2"), /* CLK */
- DB8500_PIN_SLEEP("GPIO129_B4", in_wkup_pdis_en, "sdi2"), /* CMD */
- DB8500_PIN_SLEEP("GPIO130_C8", in_wkup_pdis_en, "sdi2"), /* FBCLK */
- DB8500_PIN_SLEEP("GPIO131_A12", in_wkup_pdis, "sdi2"), /* DAT0 */
- DB8500_PIN_SLEEP("GPIO132_C10", in_wkup_pdis, "sdi2"), /* DAT1 */
- DB8500_PIN_SLEEP("GPIO133_B10", in_wkup_pdis, "sdi2"), /* DAT2 */
- DB8500_PIN_SLEEP("GPIO134_B9", in_wkup_pdis, "sdi2"), /* DAT3 */
- DB8500_PIN_SLEEP("GPIO135_A9", in_wkup_pdis, "sdi2"), /* DAT4 */
- DB8500_PIN_SLEEP("GPIO136_C7", in_wkup_pdis, "sdi2"), /* DAT5 */
- DB8500_PIN_SLEEP("GPIO137_A7", in_wkup_pdis, "sdi2"), /* DAT6 */
- DB8500_PIN_SLEEP("GPIO138_C5", in_wkup_pdis, "sdi2"), /* DAT7 */
-
- /* Mux in SDI4 (here called MC4) used for for PCB-mounted eMMC */
- DB8500_MUX("mc4_a_1", "mc4", "sdi4"),
- DB8500_PIN("GPIO197_AH24", in_pu, "sdi4"), /* DAT3 */
- DB8500_PIN("GPIO198_AG25", in_pu, "sdi4"), /* DAT2 */
- DB8500_PIN("GPIO199_AH23", in_pu, "sdi4"), /* DAT1 */
- DB8500_PIN("GPIO200_AH26", in_pu, "sdi4"), /* DAT0 */
- DB8500_PIN("GPIO201_AF24", in_pu, "sdi4"), /* CMD */
- DB8500_PIN("GPIO202_AF25", in_nopull, "sdi4"), /* FBCLK */
- DB8500_PIN("GPIO203_AE23", out_lo, "sdi4"), /* CLK */
- DB8500_PIN("GPIO204_AF23", in_pu, "sdi4"), /* DAT7 */
- DB8500_PIN("GPIO205_AG23", in_pu, "sdi4"), /* DAT6 */
- DB8500_PIN("GPIO206_AG24", in_pu, "sdi4"), /* DAT5 */
- DB8500_PIN("GPIO207_AJ23", in_pu, "sdi4"), /* DAT4 */
- /*SDI4 sleep state */
- DB8500_PIN_SLEEP("GPIO197_AH24", slpm_in_wkup_pdis, "sdi4"), /* DAT3 */
- DB8500_PIN_SLEEP("GPIO198_AG25", slpm_in_wkup_pdis, "sdi4"), /* DAT2 */
- DB8500_PIN_SLEEP("GPIO199_AH23", slpm_in_wkup_pdis, "sdi4"), /* DAT1 */
- DB8500_PIN_SLEEP("GPIO200_AH26", slpm_in_wkup_pdis, "sdi4"), /* DAT0 */
- DB8500_PIN_SLEEP("GPIO201_AF24", slpm_in_wkup_pdis, "sdi4"), /* CMD */
- DB8500_PIN_SLEEP("GPIO202_AF25", slpm_in_wkup_pdis, "sdi4"), /* FBCLK */
- DB8500_PIN_SLEEP("GPIO203_AE23", slpm_out_lo_wkup_pdis, "sdi4"), /* CLK */
- DB8500_PIN_SLEEP("GPIO204_AF23", slpm_in_wkup_pdis, "sdi4"), /* DAT7 */
- DB8500_PIN_SLEEP("GPIO205_AG23", slpm_in_wkup_pdis, "sdi4"), /* DAT6 */
- DB8500_PIN_SLEEP("GPIO206_AG24", slpm_in_wkup_pdis, "sdi4"), /* DAT5 */
- DB8500_PIN_SLEEP("GPIO207_AJ23", slpm_in_wkup_pdis, "sdi4"), /* DAT4 */
-
- /* Mux in USB pins, drive STP high */
- /* USB default state */
- DB8500_MUX("usb_a_1", "usb", "ab8500-usb.0"),
- DB8500_PIN("GPIO257_AE29", out_hi, "ab8500-usb.0"), /* STP */
- /* USB sleep state */
- DB8500_PIN_SLEEP("GPIO256_AF28", slpm_wkup_pdis_en, "ab8500-usb.0"), /* NXT */
- DB8500_PIN_SLEEP("GPIO257_AE29", slpm_out_hi_wkup_pdis, "ab8500-usb.0"), /* STP */
- DB8500_PIN_SLEEP("GPIO258_AD29", slpm_wkup_pdis_en, "ab8500-usb.0"), /* XCLK */
- DB8500_PIN_SLEEP("GPIO259_AC29", slpm_wkup_pdis_en, "ab8500-usb.0"), /* DIR */
- DB8500_PIN_SLEEP("GPIO260_AD28", slpm_in_wkup_pdis_en, "ab8500-usb.0"), /* DAT7 */
- DB8500_PIN_SLEEP("GPIO261_AD26", slpm_in_wkup_pdis_en, "ab8500-usb.0"), /* DAT6 */
- DB8500_PIN_SLEEP("GPIO262_AE26", slpm_in_wkup_pdis_en, "ab8500-usb.0"), /* DAT5 */
- DB8500_PIN_SLEEP("GPIO263_AG29", slpm_in_wkup_pdis_en, "ab8500-usb.0"), /* DAT4 */
- DB8500_PIN_SLEEP("GPIO264_AE27", slpm_in_wkup_pdis_en, "ab8500-usb.0"), /* DAT3 */
- DB8500_PIN_SLEEP("GPIO265_AD27", slpm_in_wkup_pdis_en, "ab8500-usb.0"), /* DAT2 */
- DB8500_PIN_SLEEP("GPIO266_AC28", slpm_in_wkup_pdis_en, "ab8500-usb.0"), /* DAT1 */
- DB8500_PIN_SLEEP("GPIO267_AC27", slpm_in_wkup_pdis_en, "ab8500-usb.0"), /* DAT0 */
-
- /* Mux in SPI2 pins on the "other C1" altfunction */
- DB8500_MUX("spi2_oc1_2", "spi2", "spi2"),
- DB8500_PIN("GPIO216_AG12", gpio_out_hi, "spi2"), /* FRM */
- DB8500_PIN("GPIO218_AH11", in_pd, "spi2"), /* RXD */
- DB8500_PIN("GPIO215_AH13", out_lo, "spi2"), /* TXD */
- DB8500_PIN("GPIO217_AH12", out_lo, "spi2"), /* CLK */
- /* SPI2 idle state */
- DB8500_PIN_IDLE("GPIO218_AH11", slpm_in_wkup_pdis, "spi2"), /* RXD */
- DB8500_PIN_IDLE("GPIO215_AH13", slpm_out_lo_wkup_pdis, "spi2"), /* TXD */
- DB8500_PIN_IDLE("GPIO217_AH12", slpm_wkup_pdis, "spi2"), /* CLK */
- /* SPI2 sleep state */
- DB8500_PIN_SLEEP("GPIO216_AG12", slpm_in_wkup_pdis, "spi2"), /* FRM */
- DB8500_PIN_SLEEP("GPIO218_AH11", slpm_in_wkup_pdis, "spi2"), /* RXD */
- DB8500_PIN_SLEEP("GPIO215_AH13", slpm_out_lo_wkup_pdis, "spi2"), /* TXD */
- DB8500_PIN_SLEEP("GPIO217_AH12", slpm_wkup_pdis, "spi2"), /* CLK */
-
- /* ske default state */
- DB8500_MUX("kp_a_2", "kp", "nmk-ske-keypad"),
- DB8500_PIN("GPIO153_B17", in_pd, "nmk-ske-keypad"), /* I7 */
- DB8500_PIN("GPIO154_C16", in_pd, "nmk-ske-keypad"), /* I6 */
- DB8500_PIN("GPIO155_C19", in_pd, "nmk-ske-keypad"), /* I5 */
- DB8500_PIN("GPIO156_C17", in_pd, "nmk-ske-keypad"), /* I4 */
- DB8500_PIN("GPIO161_D21", in_pd, "nmk-ske-keypad"), /* I3 */
- DB8500_PIN("GPIO162_D20", in_pd, "nmk-ske-keypad"), /* I2 */
- DB8500_PIN("GPIO163_C20", in_pd, "nmk-ske-keypad"), /* I1 */
- DB8500_PIN("GPIO164_B21", in_pd, "nmk-ske-keypad"), /* I0 */
- DB8500_PIN("GPIO157_A18", out_lo, "nmk-ske-keypad"), /* O7 */
- DB8500_PIN("GPIO158_C18", out_lo, "nmk-ske-keypad"), /* O6 */
- DB8500_PIN("GPIO159_B19", out_lo, "nmk-ske-keypad"), /* O5 */
- DB8500_PIN("GPIO160_B20", out_lo, "nmk-ske-keypad"), /* O4 */
- DB8500_PIN("GPIO165_C21", out_lo, "nmk-ske-keypad"), /* O3 */
- DB8500_PIN("GPIO166_A22", out_lo, "nmk-ske-keypad"), /* O2 */
- DB8500_PIN("GPIO167_B24", out_lo, "nmk-ske-keypad"), /* O1 */
- DB8500_PIN("GPIO168_C22", out_lo, "nmk-ske-keypad"), /* O0 */
- /* ske sleep state */
- DB8500_PIN_SLEEP("GPIO153_B17", slpm_in_pu_wkup_pdis_en, "nmk-ske-keypad"), /* I7 */
- DB8500_PIN_SLEEP("GPIO154_C16", slpm_in_pu_wkup_pdis_en, "nmk-ske-keypad"), /* I6 */
- DB8500_PIN_SLEEP("GPIO155_C19", slpm_in_pu_wkup_pdis_en, "nmk-ske-keypad"), /* I5 */
- DB8500_PIN_SLEEP("GPIO156_C17", slpm_in_pu_wkup_pdis_en, "nmk-ske-keypad"), /* I4 */
- DB8500_PIN_SLEEP("GPIO161_D21", slpm_in_pu_wkup_pdis_en, "nmk-ske-keypad"), /* I3 */
- DB8500_PIN_SLEEP("GPIO162_D20", slpm_in_pu_wkup_pdis_en, "nmk-ske-keypad"), /* I2 */
- DB8500_PIN_SLEEP("GPIO163_C20", slpm_in_pu_wkup_pdis_en, "nmk-ske-keypad"), /* I1 */
- DB8500_PIN_SLEEP("GPIO164_B21", slpm_in_pu_wkup_pdis_en, "nmk-ske-keypad"), /* I0 */
- DB8500_PIN_SLEEP("GPIO157_A18", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O7 */
- DB8500_PIN_SLEEP("GPIO158_C18", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O6 */
- DB8500_PIN_SLEEP("GPIO159_B19", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O5 */
- DB8500_PIN_SLEEP("GPIO160_B20", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O4 */
- DB8500_PIN_SLEEP("GPIO165_C21", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O3 */
- DB8500_PIN_SLEEP("GPIO166_A22", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O2 */
- DB8500_PIN_SLEEP("GPIO167_B24", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O1 */
- DB8500_PIN_SLEEP("GPIO168_C22", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O0 */
-
- /* STM APE pins states */
- DB8500_MUX_STATE("stmape_c_1", "stmape",
- "stm", "ape_mipi34"),
- DB8500_PIN_STATE("GPIO70_G5", in_nopull,
- "stm", "ape_mipi34"), /* clk */
- DB8500_PIN_STATE("GPIO71_G4", in_nopull,
- "stm", "ape_mipi34"), /* dat3 */
- DB8500_PIN_STATE("GPIO72_H4", in_nopull,
- "stm", "ape_mipi34"), /* dat2 */
- DB8500_PIN_STATE("GPIO73_H3", in_nopull,
- "stm", "ape_mipi34"), /* dat1 */
- DB8500_PIN_STATE("GPIO74_J3", in_nopull,
- "stm", "ape_mipi34"), /* dat0 */
-
- DB8500_PIN_STATE("GPIO70_G5", slpm_out_lo_pdis,
- "stm", "ape_mipi34_sleep"), /* clk */
- DB8500_PIN_STATE("GPIO71_G4", slpm_out_lo_pdis,
- "stm", "ape_mipi34_sleep"), /* dat3 */
- DB8500_PIN_STATE("GPIO72_H4", slpm_out_lo_pdis,
- "stm", "ape_mipi34_sleep"), /* dat2 */
- DB8500_PIN_STATE("GPIO73_H3", slpm_out_lo_pdis,
- "stm", "ape_mipi34_sleep"), /* dat1 */
- DB8500_PIN_STATE("GPIO74_J3", slpm_out_lo_pdis,
- "stm", "ape_mipi34_sleep"), /* dat0 */
-
- DB8500_MUX_STATE("stmape_oc1_1", "stmape",
- "stm", "ape_microsd"),
- DB8500_PIN_STATE("GPIO23_AA4", in_nopull,
- "stm", "ape_microsd"), /* clk */
- DB8500_PIN_STATE("GPIO25_Y4", in_nopull,
- "stm", "ape_microsd"), /* dat0 */
- DB8500_PIN_STATE("GPIO26_Y2", in_nopull,
- "stm", "ape_microsd"), /* dat1 */
- DB8500_PIN_STATE("GPIO27_AA2", in_nopull,
- "stm", "ape_microsd"), /* dat2 */
- DB8500_PIN_STATE("GPIO28_AA1", in_nopull,
- "stm", "ape_microsd"), /* dat3 */
-
- DB8500_PIN_STATE("GPIO23_AA4", slpm_out_lo_wkup_pdis,
- "stm", "ape_microsd_sleep"), /* clk */
- DB8500_PIN_STATE("GPIO25_Y4", slpm_in_wkup_pdis,
- "stm", "ape_microsd_sleep"), /* dat0 */
- DB8500_PIN_STATE("GPIO26_Y2", slpm_in_wkup_pdis,
- "stm", "ape_microsd_sleep"), /* dat1 */
- DB8500_PIN_STATE("GPIO27_AA2", slpm_in_wkup_pdis,
- "stm", "ape_microsd_sleep"), /* dat2 */
- DB8500_PIN_STATE("GPIO28_AA1", slpm_in_wkup_pdis,
- "stm", "ape_microsd_sleep"), /* dat3 */
-
- /* STM Modem pins states */
- DB8500_MUX_STATE("stmmod_oc3_2", "stmmod",
- "stm", "mod_mipi34"),
- DB8500_MUX_STATE("uartmodrx_oc3_1", "uartmod",
- "stm", "mod_mipi34"),
- DB8500_MUX_STATE("uartmodtx_oc3_1", "uartmod",
- "stm", "mod_mipi34"),
- DB8500_PIN_STATE("GPIO70_G5", in_nopull,
- "stm", "mod_mipi34"), /* clk */
- DB8500_PIN_STATE("GPIO71_G4", in_nopull,
- "stm", "mod_mipi34"), /* dat3 */
- DB8500_PIN_STATE("GPIO72_H4", in_nopull,
- "stm", "mod_mipi34"), /* dat2 */
- DB8500_PIN_STATE("GPIO73_H3", in_nopull,
- "stm", "mod_mipi34"), /* dat1 */
- DB8500_PIN_STATE("GPIO74_J3", in_nopull,
- "stm", "mod_mipi34"), /* dat0 */
- DB8500_PIN_STATE("GPIO75_H2", in_pu,
- "stm", "mod_mipi34"), /* uartmod rx */
- DB8500_PIN_STATE("GPIO76_J2", out_lo,
- "stm", "mod_mipi34"), /* uartmod tx */
-
- DB8500_PIN_STATE("GPIO70_G5", slpm_out_lo_pdis,
- "stm", "mod_mipi34_sleep"), /* clk */
- DB8500_PIN_STATE("GPIO71_G4", slpm_out_lo_pdis,
- "stm", "mod_mipi34_sleep"), /* dat3 */
- DB8500_PIN_STATE("GPIO72_H4", slpm_out_lo_pdis,
- "stm", "mod_mipi34_sleep"), /* dat2 */
- DB8500_PIN_STATE("GPIO73_H3", slpm_out_lo_pdis,
- "stm", "mod_mipi34_sleep"), /* dat1 */
- DB8500_PIN_STATE("GPIO74_J3", slpm_out_lo_pdis,
- "stm", "mod_mipi34_sleep"), /* dat0 */
- DB8500_PIN_STATE("GPIO75_H2", slpm_in_wkup_pdis,
- "stm", "mod_mipi34_sleep"), /* uartmod rx */
- DB8500_PIN_STATE("GPIO76_J2", slpm_out_lo_wkup_pdis,
- "stm", "mod_mipi34_sleep"), /* uartmod tx */
-
- DB8500_MUX_STATE("stmmod_b_1", "stmmod",
- "stm", "mod_microsd"),
- DB8500_MUX_STATE("uartmodrx_oc3_1", "uartmod",
- "stm", "mod_microsd"),
- DB8500_MUX_STATE("uartmodtx_oc3_1", "uartmod",
- "stm", "mod_microsd"),
- DB8500_PIN_STATE("GPIO23_AA4", in_nopull,
- "stm", "mod_microsd"), /* clk */
- DB8500_PIN_STATE("GPIO25_Y4", in_nopull,
- "stm", "mod_microsd"), /* dat0 */
- DB8500_PIN_STATE("GPIO26_Y2", in_nopull,
- "stm", "mod_microsd"), /* dat1 */
- DB8500_PIN_STATE("GPIO27_AA2", in_nopull,
- "stm", "mod_microsd"), /* dat2 */
- DB8500_PIN_STATE("GPIO28_AA1", in_nopull,
- "stm", "mod_microsd"), /* dat3 */
- DB8500_PIN_STATE("GPIO75_H2", in_pu,
- "stm", "mod_microsd"), /* uartmod rx */
- DB8500_PIN_STATE("GPIO76_J2", out_lo,
- "stm", "mod_microsd"), /* uartmod tx */
-
- DB8500_PIN_STATE("GPIO23_AA4", slpm_out_lo_wkup_pdis,
- "stm", "mod_microsd_sleep"), /* clk */
- DB8500_PIN_STATE("GPIO25_Y4", slpm_in_wkup_pdis,
- "stm", "mod_microsd_sleep"), /* dat0 */
- DB8500_PIN_STATE("GPIO26_Y2", slpm_in_wkup_pdis,
- "stm", "mod_microsd_sleep"), /* dat1 */
- DB8500_PIN_STATE("GPIO27_AA2", slpm_in_wkup_pdis,
- "stm", "mod_microsd_sleep"), /* dat2 */
- DB8500_PIN_STATE("GPIO28_AA1", slpm_in_wkup_pdis,
- "stm", "mod_microsd_sleep"), /* dat3 */
- DB8500_PIN_STATE("GPIO75_H2", slpm_in_wkup_pdis,
- "stm", "mod_microsd_sleep"), /* uartmod rx */
- DB8500_PIN_STATE("GPIO76_J2", slpm_out_lo_wkup_pdis,
- "stm", "mod_microsd_sleep"), /* uartmod tx */
-
- /* STM dual Modem/APE pins state */
- DB8500_MUX_STATE("stmmod_oc3_2", "stmmod",
- "stm", "mod_mipi34_ape_mipi60"),
- DB8500_MUX_STATE("stmape_c_2", "stmape",
- "stm", "mod_mipi34_ape_mipi60"),
- DB8500_MUX_STATE("uartmodrx_oc3_1", "uartmod",
- "stm", "mod_mipi34_ape_mipi60"),
- DB8500_MUX_STATE("uartmodtx_oc3_1", "uartmod",
- "stm", "mod_mipi34_ape_mipi60"),
- DB8500_PIN_STATE("GPIO70_G5", in_nopull,
- "stm", "mod_mipi34_ape_mipi60"), /* clk */
- DB8500_PIN_STATE("GPIO71_G4", in_nopull,
- "stm", "mod_mipi34_ape_mipi60"), /* dat3 */
- DB8500_PIN_STATE("GPIO72_H4", in_nopull,
- "stm", "mod_mipi34_ape_mipi60"), /* dat2 */
- DB8500_PIN_STATE("GPIO73_H3", in_nopull,
- "stm", "mod_mipi34_ape_mipi60"), /* dat1 */
- DB8500_PIN_STATE("GPIO74_J3", in_nopull,
- "stm", "mod_mipi34_ape_mipi60"), /* dat0 */
- DB8500_PIN_STATE("GPIO75_H2", in_pu,
- "stm", "mod_mipi34_ape_mipi60"), /* uartmod rx */
- DB8500_PIN_STATE("GPIO76_J2", out_lo,
- "stm", "mod_mipi34_ape_mipi60"), /* uartmod tx */
- DB8500_PIN_STATE("GPIO155_C19", in_nopull,
- "stm", "mod_mipi34_ape_mipi60"), /* clk */
- DB8500_PIN_STATE("GPIO156_C17", in_nopull,
- "stm", "mod_mipi34_ape_mipi60"), /* dat3 */
- DB8500_PIN_STATE("GPIO157_A18", in_nopull,
- "stm", "mod_mipi34_ape_mipi60"), /* dat2 */
- DB8500_PIN_STATE("GPIO158_C18", in_nopull,
- "stm", "mod_mipi34_ape_mipi60"), /* dat1 */
- DB8500_PIN_STATE("GPIO159_B19", in_nopull,
- "stm", "mod_mipi34_ape_mipi60"), /* dat0 */
-
- DB8500_PIN_STATE("GPIO70_G5", slpm_out_lo_pdis,
- "stm", "mod_mipi34_ape_mipi60_sleep"), /* clk */
- DB8500_PIN_STATE("GPIO71_G4", slpm_out_lo_pdis,
- "stm", "mod_mipi34_ape_mipi60_sleep"), /* dat3 */
- DB8500_PIN_STATE("GPIO72_H4", slpm_out_lo_pdis,
- "stm", "mod_mipi34_ape_mipi60_sleep"), /* dat2 */
- DB8500_PIN_STATE("GPIO73_H3", slpm_out_lo_pdis,
- "stm", "mod_mipi34_ape_mipi60_sleep"), /* dat1 */
- DB8500_PIN_STATE("GPIO74_J3", slpm_out_lo_pdis,
- "stm", "mod_mipi34_ape_mipi60_sleep"), /* dat0 */
- DB8500_PIN_STATE("GPIO75_H2", slpm_in_wkup_pdis,
- "stm", "mod_mipi34_ape_mipi60_sleep"), /* uartmod rx */
- DB8500_PIN_STATE("GPIO76_J2", slpm_out_lo_wkup_pdis,
- "stm", "mod_mipi34_ape_mipi60_sleep"), /* uartmod tx */
- DB8500_PIN_STATE("GPIO155_C19", slpm_in_wkup_pdis,
- "stm", "mod_mipi34_ape_mipi60_sleep"), /* clk */
- DB8500_PIN_STATE("GPIO156_C17", slpm_in_wkup_pdis,
- "stm", "mod_mipi34_ape_mipi60_sleep"), /* dat3 */
- DB8500_PIN_STATE("GPIO157_A18", slpm_in_wkup_pdis,
- "stm", "mod_mipi34_ape_mipi60_sleep"), /* dat2 */
- DB8500_PIN_STATE("GPIO158_C18", slpm_in_wkup_pdis,
- "stm", "mod_mipi34_ape_mipi60_sleep"), /* dat1 */
- DB8500_PIN_STATE("GPIO159_B19", slpm_in_wkup_pdis,
- "stm", "mod_mipi34_ape_mipi60_sleep"), /* dat0 */
-};
-
-/*
- * These are specifically for the MOP500 and HREFP (pre-v60) version of the
- * board, which utilized a TC35892 GPIO expander instead of using a lot of
- * on-chip pins as the HREFv60 and later does.
- */
-static struct pinctrl_map __initdata mop500_pinmap[] = {
- /* Mux in SSP0, pull down RXD pin */
- DB8500_MUX_HOG("ssp0_a_1", "ssp0"),
- DB8500_PIN_HOG("GPIO145_C13", pd),
- /*
- * XENON Flashgun on image processor GPIO (controlled from image
- * processor firmware), mux in these image processor GPIO lines 0
- * (XENON_FLASH_ID) and 1 (XENON_READY) on altfunction C and pull up
- * the pins.
- */
- DB8500_MUX_HOG("ipgpio0_c_1", "ipgpio"),
- DB8500_MUX_HOG("ipgpio1_c_1", "ipgpio"),
- DB8500_PIN_HOG("GPIO6_AF6", in_pu),
- DB8500_PIN_HOG("GPIO7_AG5", in_pu),
- /* TC35892 IRQ, pull up the line, let the driver mux in the pin */
- DB8500_PIN_HOG("GPIO217_AH12", gpio_in_pu),
- /* Mux in UART1 and set the pull-ups */
- DB8500_MUX_HOG("u1rxtx_a_1", "u1"),
- DB8500_PIN_HOG("GPIO4_AH6", in_pu), /* RXD */
- DB8500_PIN_HOG("GPIO5_AG6", out_hi), /* TXD */
- /*
- * Runtime stuff: make it possible to mux in the SKE keypad
- * and bias the pins
- */
- /* ske default state */
- DB8500_MUX("kp_a_2", "kp", "nmk-ske-keypad"),
- DB8500_PIN("GPIO153_B17", in_pu, "nmk-ske-keypad"), /* I7 */
- DB8500_PIN("GPIO154_C16", in_pu, "nmk-ske-keypad"), /* I6 */
- DB8500_PIN("GPIO155_C19", in_pu, "nmk-ske-keypad"), /* I5 */
- DB8500_PIN("GPIO156_C17", in_pu, "nmk-ske-keypad"), /* I4 */
- DB8500_PIN("GPIO161_D21", in_pu, "nmk-ske-keypad"), /* I3 */
- DB8500_PIN("GPIO162_D20", in_pu, "nmk-ske-keypad"), /* I2 */
- DB8500_PIN("GPIO163_C20", in_pu, "nmk-ske-keypad"), /* I1 */
- DB8500_PIN("GPIO164_B21", in_pu, "nmk-ske-keypad"), /* I0 */
- DB8500_PIN("GPIO157_A18", out_lo, "nmk-ske-keypad"), /* O7 */
- DB8500_PIN("GPIO158_C18", out_lo, "nmk-ske-keypad"), /* O6 */
- DB8500_PIN("GPIO159_B19", out_lo, "nmk-ske-keypad"), /* O5 */
- DB8500_PIN("GPIO160_B20", out_lo, "nmk-ske-keypad"), /* O4 */
- DB8500_PIN("GPIO165_C21", out_lo, "nmk-ske-keypad"), /* O3 */
- DB8500_PIN("GPIO166_A22", out_lo, "nmk-ske-keypad"), /* O2 */
- DB8500_PIN("GPIO167_B24", out_lo, "nmk-ske-keypad"), /* O1 */
- DB8500_PIN("GPIO168_C22", out_lo, "nmk-ske-keypad"), /* O0 */
- /* ske sleep state */
- DB8500_PIN_SLEEP("GPIO153_B17", slpm_in_pu_wkup_pdis_en, "nmk-ske-keypad"), /* I7 */
- DB8500_PIN_SLEEP("GPIO154_C16", slpm_in_pu_wkup_pdis_en, "nmk-ske-keypad"), /* I6 */
- DB8500_PIN_SLEEP("GPIO155_C19", slpm_in_pu_wkup_pdis_en, "nmk-ske-keypad"), /* I5 */
- DB8500_PIN_SLEEP("GPIO156_C17", slpm_in_pu_wkup_pdis_en, "nmk-ske-keypad"), /* I4 */
- DB8500_PIN_SLEEP("GPIO161_D21", slpm_in_pu_wkup_pdis_en, "nmk-ske-keypad"), /* I3 */
- DB8500_PIN_SLEEP("GPIO162_D20", slpm_in_pu_wkup_pdis_en, "nmk-ske-keypad"), /* I2 */
- DB8500_PIN_SLEEP("GPIO163_C20", slpm_in_pu_wkup_pdis_en, "nmk-ske-keypad"), /* I1 */
- DB8500_PIN_SLEEP("GPIO164_B21", slpm_in_pu_wkup_pdis_en, "nmk-ske-keypad"), /* I0 */
- DB8500_PIN_SLEEP("GPIO157_A18", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O7 */
- DB8500_PIN_SLEEP("GPIO158_C18", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O6 */
- DB8500_PIN_SLEEP("GPIO159_B19", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O5 */
- DB8500_PIN_SLEEP("GPIO160_B20", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O4 */
- DB8500_PIN_SLEEP("GPIO165_C21", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O3 */
- DB8500_PIN_SLEEP("GPIO166_A22", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O2 */
- DB8500_PIN_SLEEP("GPIO167_B24", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O1 */
- DB8500_PIN_SLEEP("GPIO168_C22", slpm_out_lo_pdis, "nmk-ske-keypad"), /* O0 */
-
- /* Mux in and drive the SDI0 DAT31DIR line high at runtime */
- DB8500_MUX("mc0dat31dir_a_1", "mc0", "sdi0"),
- DB8500_PIN("GPIO21_AB3", out_hi, "sdi0"),
-};
-
-/*
- * The HREFv60 series of platforms is using available pins on the DB8500
- * insteaf of the Toshiba I2C GPIO expander, reusing some pins like the SSP0
- * and SSP1 ports (previously connected to the AB8500) as generic GPIO lines.
- */
-static struct pinctrl_map __initdata hrefv60_pinmap[] = {
- /* Drive WLAN_ENA low */
- DB8500_PIN_HOG("GPIO85_D5", gpio_out_lo), /* WLAN_ENA */
- /*
- * XENON Flashgun on image processor GPIO (controlled from image
- * processor firmware), mux in these image processor GPIO lines 0
- * (XENON_FLASH_ID), 1 (XENON_READY) and there is an assistant
- * LED on IP GPIO 4 (XENON_EN2) on altfunction C, that need bias
- * from GPIO21 so pull up 0, 1 and drive 4 and GPIO21 low as output.
- */
- DB8500_MUX_HOG("ipgpio0_c_1", "ipgpio"),
- DB8500_MUX_HOG("ipgpio1_c_1", "ipgpio"),
- DB8500_MUX_HOG("ipgpio4_c_1", "ipgpio"),
- DB8500_PIN_HOG("GPIO6_AF6", in_pu), /* XENON_FLASH_ID */
- DB8500_PIN_HOG("GPIO7_AG5", in_pu), /* XENON_READY */
- DB8500_PIN_HOG("GPIO21_AB3", gpio_out_lo), /* XENON_EN1 */
- DB8500_PIN_HOG("GPIO64_F3", out_lo), /* XENON_EN2 */
- /* Magnetometer uses GPIO 31 and 32, pull these up/down respectively */
- DB8500_PIN_HOG("GPIO31_V3", gpio_in_pu), /* EN1 */
- DB8500_PIN_HOG("GPIO32_V2", gpio_in_pd), /* DRDY */
- /*
- * Display Interface 1 uses GPIO 65 for RST (reset).
- * Display Interface 2 uses GPIO 66 for RST (reset).
- * Drive DISP1 reset high (not reset), driver DISP2 reset low (reset)
- */
- DB8500_PIN_HOG("GPIO65_F1", gpio_out_hi), /* DISP1 NO RST */
- DB8500_PIN_HOG("GPIO66_G3", gpio_out_lo), /* DISP2 RST */
- /*
- * Touch screen uses GPIO 143 for RST1, GPIO 146 for RST2 and
- * GPIO 67 for interrupts. Pull-up the IRQ line and drive both
- * reset signals low.
- */
- DB8500_PIN_HOG("GPIO143_D12", gpio_out_lo), /* TOUCH_RST1 */
- DB8500_PIN_HOG("GPIO67_G2", gpio_in_pu), /* TOUCH_INT2 */
- DB8500_PIN_HOG("GPIO146_D13", gpio_out_lo), /* TOUCH_RST2 */
- /*
- * Drive D19-D23 for the ETM PTM trace interface low,
- * (presumably pins are unconnected therefore grounded here,
- * the "other alt C1" setting enables these pins)
- */
- DB8500_PIN_HOG("GPIO70_G5", gpio_out_lo),
- DB8500_PIN_HOG("GPIO71_G4", gpio_out_lo),
- DB8500_PIN_HOG("GPIO72_H4", gpio_out_lo),
- DB8500_PIN_HOG("GPIO73_H3", gpio_out_lo),
- DB8500_PIN_HOG("GPIO74_J3", gpio_out_lo),
- /* NAHJ CTRL on GPIO 76 to low, CTRL_INV on GPIO216 to high */
- DB8500_PIN_HOG("GPIO76_J2", gpio_out_lo), /* CTRL */
- DB8500_PIN_HOG("GPIO216_AG12", gpio_out_hi), /* CTRL_INV */
- /* NFC ENA and RESET to low, pulldown IRQ line */
- DB8500_PIN_HOG("GPIO77_H1", gpio_out_lo), /* NFC_ENA */
- DB8500_PIN_HOG("GPIO144_B13", gpio_in_pd), /* NFC_IRQ */
- DB8500_PIN_HOG("GPIO142_C11", gpio_out_lo), /* NFC_RESET */
- /*
- * SKE keyboard partly on alt A and partly on "Other alt C1"
- * Driver KP_O1,2,3,6,7 low and pull up KP_I 0,2,3 for three
- * rows of 6 keys, then pull up force sensing interrup and
- * drive reset and force sensing WU low.
- */
- DB8500_MUX_HOG("kp_a_1", "kp"),
- DB8500_MUX_HOG("kp_oc1_1", "kp"),
- DB8500_PIN_HOG("GPIO90_A3", out_lo), /* KP_O1 */
- DB8500_PIN_HOG("GPIO87_B3", out_lo), /* KP_O2 */
- DB8500_PIN_HOG("GPIO86_C6", out_lo), /* KP_O3 */
- DB8500_PIN_HOG("GPIO96_D8", out_lo), /* KP_O6 */
- DB8500_PIN_HOG("GPIO94_D7", out_lo), /* KP_O7 */
- DB8500_PIN_HOG("GPIO93_B7", in_pu), /* KP_I0 */
- DB8500_PIN_HOG("GPIO89_E6", in_pu), /* KP_I2 */
- DB8500_PIN_HOG("GPIO88_C4", in_pu), /* KP_I3 */
- DB8500_PIN_HOG("GPIO91_B6", gpio_in_pu), /* FORCE_SENSING_INT */
- DB8500_PIN_HOG("GPIO92_D6", gpio_out_lo), /* FORCE_SENSING_RST */
- DB8500_PIN_HOG("GPIO97_D9", gpio_out_lo), /* FORCE_SENSING_WU */
- /* DiPro Sensor interrupt */
- DB8500_PIN_HOG("GPIO139_C9", gpio_in_pu), /* DIPRO_INT */
- /* Audio Amplifier HF enable */
- DB8500_PIN_HOG("GPIO149_B14", gpio_out_hi), /* VAUDIO_HF_EN, enable MAX8968 */
- /* GBF interface, pull low to reset state */
- DB8500_PIN_HOG("GPIO171_D23", gpio_out_lo), /* GBF_ENA_RESET */
- /* MSP : HDTV INTERFACE GPIO line */
- DB8500_PIN_HOG("GPIO192_AJ27", gpio_in_pd),
- /* Accelerometer interrupt lines */
- DB8500_PIN_HOG("GPIO82_C1", gpio_in_pu), /* ACC_INT1 */
- DB8500_PIN_HOG("GPIO83_D3", gpio_in_pu), /* ACC_INT2 */
- /* SD card detect GPIO pin */
- DB8500_PIN_HOG("GPIO95_E8", gpio_in_pu),
- /*
- * Runtime stuff
- * Pull up/down of some sensor GPIO pins, for proximity, HAL sensor
- * etc.
- */
- DB8500_PIN("GPIO217_AH12", gpio_in_pu_slpm_gpio_nopull, "gpio-keys.0"),
- DB8500_PIN("GPIO145_C13", gpio_in_pd_slpm_gpio_nopull, "gpio-keys.0"),
- DB8500_PIN("GPIO139_C9", gpio_in_pu_slpm_gpio_nopull, "gpio-keys.0"),
-};
-
-static struct pinctrl_map __initdata u9500_pinmap[] = {
- /* Mux in UART1 (just RX/TX) and set the pull-ups */
- DB8500_MUX_HOG("u1rxtx_a_1", "u1"),
- DB8500_PIN_HOG("GPIO4_AH6", in_pu),
- DB8500_PIN_HOG("GPIO5_AG6", out_hi),
- /* WLAN_IRQ line */
- DB8500_PIN_HOG("GPIO144_B13", gpio_in_pu),
- /* HSI */
- DB8500_MUX_HOG("hsir_a_1", "hsi"),
- DB8500_MUX_HOG("hsit_a_2", "hsi"),
- DB8500_PIN_HOG("GPIO219_AG10", in_pd), /* RX FLA0 */
- DB8500_PIN_HOG("GPIO220_AH10", in_pd), /* RX DAT0 */
- DB8500_PIN_HOG("GPIO221_AJ11", out_lo), /* RX RDY0 */
- DB8500_PIN_HOG("GPIO222_AJ9", out_lo), /* TX FLA0 */
- DB8500_PIN_HOG("GPIO223_AH9", out_lo), /* TX DAT0 */
- DB8500_PIN_HOG("GPIO224_AG9", in_pd), /* TX RDY0 */
- DB8500_PIN_HOG("GPIO225_AG8", in_pd), /* CAWAKE0 */
- DB8500_PIN_HOG("GPIO226_AF8", gpio_out_hi), /* ACWAKE0 */
-};
-
-static struct pinctrl_map __initdata u8500_pinmap[] = {
- DB8500_PIN_HOG("GPIO226_AF8", gpio_out_lo), /* WLAN_PMU_EN */
- DB8500_PIN_HOG("GPIO4_AH6", gpio_in_pu), /* WLAN_IRQ */
-};
-
-static struct pinctrl_map __initdata snowball_pinmap[] = {
- /* Mux in SSP0 connected to AB8500, pull down RXD pin */
- DB8500_MUX_HOG("ssp0_a_1", "ssp0"),
- DB8500_PIN_HOG("GPIO145_C13", pd),
- /* Always drive the MC0 DAT31DIR line high on these boards */
- DB8500_PIN_HOG("GPIO21_AB3", out_hi),
- /* Mux in "SM" which is used for the SMSC911x Ethernet adapter */
- DB8500_MUX_HOG("sm_b_1", "sm"),
- /* User LED */
- DB8500_PIN_HOG("GPIO142_C11", gpio_out_hi),
- /* Drive RSTn_LAN high */
- DB8500_PIN_HOG("GPIO141_C12", gpio_out_hi),
- /* Accelerometer/Magnetometer */
- DB8500_PIN_HOG("GPIO163_C20", gpio_in_pu), /* ACCEL_IRQ1 */
- DB8500_PIN_HOG("GPIO164_B21", gpio_in_pu), /* ACCEL_IRQ2 */
- DB8500_PIN_HOG("GPIO165_C21", gpio_in_pu), /* MAG_DRDY */
- /* WLAN/GBF */
- DB8500_PIN_HOG("GPIO161_D21", gpio_out_lo), /* WLAN_PMU_EN */
- DB8500_PIN_HOG("GPIO171_D23", gpio_out_hi), /* GBF_ENA */
- DB8500_PIN_HOG("GPIO215_AH13", gpio_out_lo), /* WLAN_ENA */
- DB8500_PIN_HOG("GPIO216_AG12", gpio_in_pu), /* WLAN_IRQ */
-};
-
-/*
- * passing "pinsfor=" in kernel cmdline allows for custom
- * configuration of GPIOs on u8500 derived boards.
- */
-static int __init early_pinsfor(char *p)
-{
- pinsfor = PINS_FOR_DEFAULT;
-
- if (strcmp(p, "u9500-21") == 0)
- pinsfor = PINS_FOR_U9500;
-
- return 0;
-}
-early_param("pinsfor", early_pinsfor);
-
-int pins_for_u9500(void)
-{
- if (pinsfor == PINS_FOR_U9500)
- return 1;
-
- return 0;
-}
-
-static void __init mop500_href_family_pinmaps_init(void)
-{
- switch (pinsfor) {
- case PINS_FOR_U9500:
- pinctrl_register_mappings(u9500_pinmap,
- ARRAY_SIZE(u9500_pinmap));
- break;
- case PINS_FOR_DEFAULT:
- pinctrl_register_mappings(u8500_pinmap,
- ARRAY_SIZE(u8500_pinmap));
- default:
- break;
- }
-}
-
void __init mop500_pinmaps_init(void)
{
- pinctrl_register_mappings(mop500_family_pinmap,
- ARRAY_SIZE(mop500_family_pinmap));
- pinctrl_register_mappings(mop500_pinmap,
- ARRAY_SIZE(mop500_pinmap));
- mop500_href_family_pinmaps_init();
if (machine_is_u8520())
pinctrl_register_mappings(ab8505_pinmap,
ARRAY_SIZE(ab8505_pinmap));
void __init snowball_pinmaps_init(void)
{
- pinctrl_register_mappings(mop500_family_pinmap,
- ARRAY_SIZE(mop500_family_pinmap));
- pinctrl_register_mappings(snowball_pinmap,
- ARRAY_SIZE(snowball_pinmap));
- pinctrl_register_mappings(u8500_pinmap,
- ARRAY_SIZE(u8500_pinmap));
pinctrl_register_mappings(ab8500_pinmap,
ARRAY_SIZE(ab8500_pinmap));
}
void __init hrefv60_pinmaps_init(void)
{
- pinctrl_register_mappings(mop500_family_pinmap,
- ARRAY_SIZE(mop500_family_pinmap));
- pinctrl_register_mappings(hrefv60_pinmap,
- ARRAY_SIZE(hrefv60_pinmap));
- mop500_href_family_pinmaps_init();
pinctrl_register_mappings(ab8500_pinmap,
ARRAY_SIZE(ab8500_pinmap));
}
#include <linux/platform_data/dma-ste-dma40.h>
#include <asm/mach-types.h>
-#include "devices.h"
#include "db8500-regs.h"
-#include "devices-db8500.h"
#include "board-mop500.h"
#include "ste-dma40-db8500.h"
+++ /dev/null
-/*
- * Copyright (C) 2008-2012 ST-Ericsson
- *
- * Author: Srinidhi KASAGAR <srinidhi.kasagar@stericsson.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2, as
- * published by the Free Software Foundation.
- *
- */
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/platform_device.h>
-#include <linux/clk.h>
-#include <linux/io.h>
-#include <linux/platform_data/db8500_thermal.h>
-#include <linux/amba/bus.h>
-#include <linux/amba/pl022.h>
-#include <linux/mfd/abx500/ab8500.h>
-#include <linux/regulator/ab8500.h>
-#include <linux/regulator/fixed.h>
-#include <linux/regulator/driver.h>
-#include <linux/mfd/tps6105x.h>
-#include <linux/platform_data/leds-lp55xx.h>
-#include <linux/input.h>
-#include <linux/delay.h>
-#include <linux/leds.h>
-#include <linux/pinctrl/consumer.h>
-#include <linux/platform_data/pinctrl-nomadik.h>
-#include <linux/platform_data/dma-ste-dma40.h>
-
-#include <asm/mach-types.h>
-
-#include "setup.h"
-#include "devices.h"
-#include "irqs.h"
-
-#include "ste-dma40-db8500.h"
-#include "db8500-regs.h"
-#include "devices-db8500.h"
-#include "board-mop500.h"
-#include "board-mop500-regulators.h"
-
-struct ab8500_platform_data ab8500_platdata = {
- .irq_base = MOP500_AB8500_IRQ_BASE,
- .regulator = &ab8500_regulator_plat_data,
-};
-
-#ifdef CONFIG_STE_DMA40
-static struct stedma40_chan_cfg ssp0_dma_cfg_rx = {
- .mode = STEDMA40_MODE_LOGICAL,
- .dir = DMA_DEV_TO_MEM,
- .dev_type = DB8500_DMA_DEV8_SSP0,
-};
-
-static struct stedma40_chan_cfg ssp0_dma_cfg_tx = {
- .mode = STEDMA40_MODE_LOGICAL,
- .dir = DMA_MEM_TO_DEV,
- .dev_type = DB8500_DMA_DEV8_SSP0,
-};
-#endif
-
-struct pl022_ssp_controller ssp0_plat = {
- .bus_id = 0,
-#ifdef CONFIG_STE_DMA40
- .enable_dma = 1,
- .dma_filter = stedma40_filter,
- .dma_rx_param = &ssp0_dma_cfg_rx,
- .dma_tx_param = &ssp0_dma_cfg_tx,
-#else
- .enable_dma = 0,
-#endif
- /* on this platform, gpio 31,142,144,214 &
- * 224 are connected as chip selects
- */
- .num_chipselect = 5,
-};
extern struct msp_i2s_platform_data msp1_platform_data;
extern struct msp_i2s_platform_data msp2_platform_data;
extern struct msp_i2s_platform_data msp3_platform_data;
-extern struct pl022_ssp_controller ssp0_plat;
void __init mop500_pinmaps_init(void);
void __init snowball_pinmaps_init(void);
#include <linux/of.h>
#include <linux/of_platform.h>
#include <linux/regulator/machine.h>
-#include <linux/platform_data/pinctrl-nomadik.h>
#include <linux/random.h>
#include <asm/pmu.h>
#include <asm/mach/map.h>
#include "setup.h"
-#include "devices.h"
#include "irqs.h"
-#include "devices-db8500.h"
-#include "db8500-regs.h"
+#include "board-mop500-regulators.h"
#include "board-mop500.h"
+#include "db8500-regs.h"
#include "id.h"
+struct ab8500_platform_data ab8500_platdata = {
+ .irq_base = MOP500_AB8500_IRQ_BASE,
+ .regulator = &ab8500_regulator_plat_data,
+};
+
+struct prcmu_pdata db8500_prcmu_pdata = {
+ .ab_platdata = &ab8500_platdata,
+ .ab_irq = IRQ_DB8500_AB8500,
+ .irq_base = IRQ_PRCMU_BASE,
+ .version_offset = DB8500_PRCMU_FW_VERSION_OFFSET,
+ .legacy_offset = DB8500_PRCMU_LEGACY_OFFSET,
+};
+
/* minimum static i/o mapping required to boot U8500 platforms */
static struct map_desc u8500_uart_io_desc[] __initdata = {
__IO_DEV_DESC(U8500_UART0_BASE, SZ_4K),
OF_DEV_AUXDATA("stericsson,ux500-hash", 0xa03c2000, "hash1", NULL),
OF_DEV_AUXDATA("stericsson,snd-soc-mop500", 0, "snd-soc-mop500.0",
NULL),
- /* Requires device name bindings. */
- OF_DEV_AUXDATA("stericsson,db8500-pinctrl", U8500_PRCMU_BASE,
- "pinctrl-db8500", NULL),
{},
};
#include <asm/mach/map.h>
#include "setup.h"
-#include "devices.h"
#include "board-mop500.h"
#include "db8500-regs.h"
} else
ux500_unknown_soc();
-#ifdef CONFIG_OF
- if (of_have_populated_dt())
- irqchip_init();
- else
-#endif
- gic_init(0, 29, dist_base, cpu_base);
+ irqchip_init();
/*
* Init clocks here so that they are available for system timer
prcmu_early_init(U8500_PRCMU_BASE, SZ_8K - 1);
ux500_pm_init(U8500_PRCMU_BASE, SZ_8K - 1);
- if (of_have_populated_dt())
- u8500_of_clk_init(U8500_CLKRST1_BASE,
- U8500_CLKRST2_BASE,
- U8500_CLKRST3_BASE,
- U8500_CLKRST5_BASE,
- U8500_CLKRST6_BASE);
- else
- u8500_clk_init(U8500_CLKRST1_BASE, U8500_CLKRST2_BASE,
- U8500_CLKRST3_BASE, U8500_CLKRST5_BASE,
- U8500_CLKRST6_BASE);
+ u8500_of_clk_init(U8500_CLKRST1_BASE,
+ U8500_CLKRST2_BASE,
+ U8500_CLKRST3_BASE,
+ U8500_CLKRST5_BASE,
+ U8500_CLKRST6_BASE);
} else if (cpu_is_u9540()) {
prcmu_early_init(U8500_PRCMU_BASE, SZ_8K - 1);
ux500_pm_init(U8500_PRCMU_BASE, SZ_8K - 1);
+++ /dev/null
-/*
- * Copyright (C) ST-Ericsson SA 2010
- *
- * Author: Rabin Vincent <rabin.vincent@stericsson.com> for ST-Ericsson
- * License terms: GNU General Public License (GPL) version 2
- */
-
-#include <linux/kernel.h>
-#include <linux/platform_device.h>
-#include <linux/interrupt.h>
-#include <linux/io.h>
-#include <linux/amba/bus.h>
-#include <linux/amba/pl022.h>
-#include <linux/mfd/dbx500-prcmu.h>
-
-#include "setup.h"
-#include "irqs.h"
-
-#include "db8500-regs.h"
-#include "devices-db8500.h"
-
-struct prcmu_pdata db8500_prcmu_pdata = {
- .ab_platdata = &ab8500_platdata,
- .ab_irq = IRQ_DB8500_AB8500,
- .irq_base = IRQ_PRCMU_BASE,
- .version_offset = DB8500_PRCMU_FW_VERSION_OFFSET,
- .legacy_offset = DB8500_PRCMU_LEGACY_OFFSET,
-};
+++ /dev/null
-/*
- * Copyright (C) ST-Ericsson SA 2010
- *
- * Author: Rabin Vincent <rabin.vincent@stericsson.com> for ST-Ericsson
- * License terms: GNU General Public License (GPL), version 2.
- */
-
-#ifndef __DEVICES_DB8500_H
-#define __DEVICES_DB8500_H
-
-#include "irqs.h"
-#include "db8500-regs.h"
-
-struct platform_device;
-
-extern struct ab8500_platform_data ab8500_platdata;
-extern struct prcmu_pdata db8500_prcmu_pdata;
-
-#endif
+++ /dev/null
-/*
- * Copyright (C) ST-Ericsson SA 2010
- *
- * Author: Rabin Vincent <rabin.vincent@stericsson.com> for ST-Ericsson
- * License terms: GNU General Public License (GPL) version 2
- */
-
-#include <linux/kernel.h>
-#include <linux/platform_device.h>
-#include <linux/interrupt.h>
-#include <linux/io.h>
-#include <linux/amba/bus.h>
-
-#include "setup.h"
-
-#include "db8500-regs.h"
-
-void __init amba_add_devices(struct amba_device *devs[], int num)
-{
- int i;
-
- for (i = 0; i < num; i++) {
- struct amba_device *d = devs[i];
- amba_device_register(d, &iomem_resource);
- }
-}
+++ /dev/null
-/*
- * Copyright (C) ST-Ericsson SA 2010
- *
- * License terms: GNU General Public License (GPL) version 2
- */
-
-#ifndef __ASM_ARCH_DEVICES_H__
-#define __ASM_ARCH_DEVICES_H__
-
-struct platform_device;
-struct amba_device;
-
-extern struct amba_device ux500_pl031_device;
-
-#endif
void ux500_restart(enum reboot_mode mode, const char *cmd);
void __init ux500_map_io(void);
-extern void __init u8500_map_io(void);
-
-extern struct device * __init u8500_init_devices(void);
extern void __init ux500_init_irq(void);
extern struct device *ux500_soc_device_init(const char *soc_id);
-struct amba_device;
-extern void __init amba_add_devices(struct amba_device *devs[], int num);
-
extern void ux500_timer_init(void);
#define __IO_DEV_DESC(x, sz) { \
#include <linux/clocksource.h>
#include <linux/of.h>
#include <linux/of_address.h>
-#include <linux/platform_data/clocksource-nomadik-mtu.h>
-
-#include <asm/smp_twd.h>
#include "setup.h"
-#include "irqs.h"
#include "db8500-regs.h"
#include "id.h"
-#ifdef CONFIG_HAVE_ARM_TWD
-static DEFINE_TWD_LOCAL_TIMER(u8500_twd_local_timer,
- U8500_TWD_BASE, IRQ_LOCALTIMER);
-
-static void __init ux500_twd_init(void)
-{
- struct twd_local_timer *twd_local_timer;
- int err;
-
- /* Use this to switch local timer base if changed in new ASICs */
- twd_local_timer = &u8500_twd_local_timer;
-
- if (of_have_populated_dt())
- clocksource_of_init();
- else {
- err = twd_local_timer_register(twd_local_timer);
- if (err)
- pr_err("twd_local_timer_register failed %d\n", err);
- }
-}
-#else
-#define ux500_twd_init() do { } while(0)
-#endif
-
const static struct of_device_id prcmu_timer_of_match[] __initconst = {
{ .compatible = "stericsson,db8500-prcmu-timer-4", },
{ },
void __init ux500_timer_init(void)
{
- void __iomem *mtu_timer_base;
void __iomem *prcmu_timer_base;
void __iomem *tmp_base;
struct device_node *np;
- if (cpu_is_u8500_family() || cpu_is_ux540_family()) {
- mtu_timer_base = __io_address(U8500_MTU0_BASE);
+ if (cpu_is_u8500_family() || cpu_is_ux540_family())
prcmu_timer_base = __io_address(U8500_PRCMU_TIMER_4_BASE);
- } else {
+ else
ux500_unknown_soc();
- }
- /* TODO: Once MTU has been DT:ed place code above into else. */
- if (of_have_populated_dt()) {
-#ifdef CONFIG_OF
- np = of_find_matching_node(NULL, prcmu_timer_of_match);
- if (!np)
-#endif
- goto dt_fail;
+ np = of_find_matching_node(NULL, prcmu_timer_of_match);
+ if (!np)
+ goto dt_fail;
- tmp_base = of_iomap(np, 0);
- if (!tmp_base)
- goto dt_fail;
+ tmp_base = of_iomap(np, 0);
+ if (!tmp_base)
+ goto dt_fail;
- prcmu_timer_base = tmp_base;
- }
+ prcmu_timer_base = tmp_base;
dt_fail:
- /* Doing it the old fashioned way. */
-
- /*
- * Here we register the timerblocks active in the system.
- * Localtimers (twd) is started when both cpu is up and running.
- * MTU register a clocksource, clockevent and sched_clock.
- * Since the MTU is located in the VAPE power domain
- * it will be cleared in sleep which makes it unsuitable.
- * We however need it as a timer tick (clockevent)
- * during boot to calibrate delay until twd is started.
- * RTC-RTT have problems as timer tick during boot since it is
- * depending on delay which is not yet calibrated. RTC-RTT is in the
- * always-on powerdomain and is used as clockevent instead of twd when
- * sleeping.
- * The PRCMU timer 4 register a clocksource and
- * sched_clock with higher rating then MTU since is always-on.
- *
- */
- if (!of_have_populated_dt())
- nmdk_timer_init(mtu_timer_base, IRQ_MTU0);
clksrc_dbx500_prcmu_init(prcmu_timer_base);
- ux500_twd_init();
+ clocksource_of_init();
}
#include <linux/jiffies.h>
#include <linux/delay.h>
#include <linux/err.h>
-#include <linux/platform_data/clocksource-nomadik-mtu.h>
#include <linux/sched_clock.h>
#include <asm/mach/time.h>
return 0;
}
-void nmdk_clkevt_reset(void)
+static void nmdk_clkevt_reset(void)
{
if (clkevt_periodic) {
/* Timer: configure load and background-load, and fire it up */
}
}
-void nmdk_clksrc_reset(void)
+static void nmdk_clksrc_reset(void)
{
/* Disable */
writel(0, mtu_base + MTU_CR(0));
.dev_id = &nmdk_clkevt,
};
-static void __init __nmdk_timer_init(void __iomem *base, int irq,
- struct clk *pclk, struct clk *clk)
+static void __init nmdk_timer_init(void __iomem *base, int irq,
+ struct clk *pclk, struct clk *clk)
{
unsigned long rate;
register_current_timer_delay(&mtu_delay_timer);
}
-void __init nmdk_timer_init(void __iomem *base, int irq)
-{
- struct clk *clk0, *pclk0;
-
- pclk0 = clk_get_sys("mtu0", "apb_pclk");
- BUG_ON(IS_ERR(pclk0));
- clk0 = clk_get_sys("mtu0", NULL);
- BUG_ON(IS_ERR(clk0));
-
- __nmdk_timer_init(base, irq, pclk0, clk0);
-}
-
static void __init nmdk_timer_of_init(struct device_node *node)
{
struct clk *pclk;
if (irq <= 0)
panic("Can't parse IRQ");
- __nmdk_timer_init(base, irq, pclk, clk);
+ nmdk_timer_init(base, irq, pclk, clk);
}
CLOCKSOURCE_OF_DECLARE(nomadik_mtu, "st,nomadik-mtu",
nmdk_timer_of_init);
#define D40_DT_FLAGS_DIR(flags) ((flags >> 1) & 0x1)
#define D40_DT_FLAGS_BIG_ENDIAN(flags) ((flags >> 2) & 0x1)
#define D40_DT_FLAGS_FIXED_CHAN(flags) ((flags >> 3) & 0x1)
+#define D40_DT_FLAGS_HIGH_PRIO(flags) ((flags >> 4) & 0x1)
static struct dma_chan *d40_xlate(struct of_phandle_args *dma_spec,
struct of_dma *ofdma)
cfg.use_fixed_channel = true;
}
+ if (D40_DT_FLAGS_HIGH_PRIO(flags))
+ cfg.high_priority = true;
+
return dma_request_channel(cap, stedma40_filter, &cfg);
}
* Copyright (C) 2008,2009 STMicroelectronics
* Copyright (C) 2009 Alessandro Rubini <rubini@unipv.it>
* Rewritten based on work by Prafulla WADASKAR <prafulla.wadaskar@st.com>
- * Copyright (C) 2011 Linus Walleij <linus.walleij@linaro.org>
+ * Copyright (C) 2011-2013 Linus Walleij <linus.walleij@linaro.org>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
#include <linux/pinctrl/pinconf.h>
/* Since we request GPIOs from ourself */
#include <linux/pinctrl/consumer.h>
-#include <linux/platform_data/pinctrl-nomadik.h>
#include "pinctrl-nomadik.h"
#include "core.h"
* Symbols in this file are called "nmk_gpio" for "nomadik gpio"
*/
+/*
+ * pin configurations are represented by 32-bit integers:
+ *
+ * bit 0.. 8 - Pin Number (512 Pins Maximum)
+ * bit 9..10 - Alternate Function Selection
+ * bit 11..12 - Pull up/down state
+ * bit 13 - Sleep mode behaviour
+ * bit 14 - Direction
+ * bit 15 - Value (if output)
+ * bit 16..18 - SLPM pull up/down state
+ * bit 19..20 - SLPM direction
+ * bit 21..22 - SLPM Value (if output)
+ * bit 23..25 - PDIS value (if input)
+ * bit 26 - Gpio mode
+ * bit 27 - Sleep mode
+ *
+ * to facilitate the definition, the following macros are provided
+ *
+ * PIN_CFG_DEFAULT - default config (0):
+ * pull up/down = disabled
+ * sleep mode = input/wakeup
+ * direction = input
+ * value = low
+ * SLPM direction = same as normal
+ * SLPM pull = same as normal
+ * SLPM value = same as normal
+ *
+ * PIN_CFG - default config with alternate function
+ */
+
+typedef unsigned long pin_cfg_t;
+
+#define PIN_NUM_MASK 0x1ff
+#define PIN_NUM(x) ((x) & PIN_NUM_MASK)
+
+#define PIN_ALT_SHIFT 9
+#define PIN_ALT_MASK (0x3 << PIN_ALT_SHIFT)
+#define PIN_ALT(x) (((x) & PIN_ALT_MASK) >> PIN_ALT_SHIFT)
+#define PIN_GPIO (NMK_GPIO_ALT_GPIO << PIN_ALT_SHIFT)
+#define PIN_ALT_A (NMK_GPIO_ALT_A << PIN_ALT_SHIFT)
+#define PIN_ALT_B (NMK_GPIO_ALT_B << PIN_ALT_SHIFT)
+#define PIN_ALT_C (NMK_GPIO_ALT_C << PIN_ALT_SHIFT)
+
+#define PIN_PULL_SHIFT 11
+#define PIN_PULL_MASK (0x3 << PIN_PULL_SHIFT)
+#define PIN_PULL(x) (((x) & PIN_PULL_MASK) >> PIN_PULL_SHIFT)
+#define PIN_PULL_NONE (NMK_GPIO_PULL_NONE << PIN_PULL_SHIFT)
+#define PIN_PULL_UP (NMK_GPIO_PULL_UP << PIN_PULL_SHIFT)
+#define PIN_PULL_DOWN (NMK_GPIO_PULL_DOWN << PIN_PULL_SHIFT)
+
+#define PIN_SLPM_SHIFT 13
+#define PIN_SLPM_MASK (0x1 << PIN_SLPM_SHIFT)
+#define PIN_SLPM(x) (((x) & PIN_SLPM_MASK) >> PIN_SLPM_SHIFT)
+#define PIN_SLPM_MAKE_INPUT (NMK_GPIO_SLPM_INPUT << PIN_SLPM_SHIFT)
+#define PIN_SLPM_NOCHANGE (NMK_GPIO_SLPM_NOCHANGE << PIN_SLPM_SHIFT)
+/* These two replace the above in DB8500v2+ */
+#define PIN_SLPM_WAKEUP_ENABLE (NMK_GPIO_SLPM_WAKEUP_ENABLE << PIN_SLPM_SHIFT)
+#define PIN_SLPM_WAKEUP_DISABLE (NMK_GPIO_SLPM_WAKEUP_DISABLE << PIN_SLPM_SHIFT)
+#define PIN_SLPM_USE_MUX_SETTINGS_IN_SLEEP PIN_SLPM_WAKEUP_DISABLE
+
+#define PIN_SLPM_GPIO PIN_SLPM_WAKEUP_ENABLE /* In SLPM, pin is a gpio */
+#define PIN_SLPM_ALTFUNC PIN_SLPM_WAKEUP_DISABLE /* In SLPM, pin is altfunc */
+
+#define PIN_DIR_SHIFT 14
+#define PIN_DIR_MASK (0x1 << PIN_DIR_SHIFT)
+#define PIN_DIR(x) (((x) & PIN_DIR_MASK) >> PIN_DIR_SHIFT)
+#define PIN_DIR_INPUT (0 << PIN_DIR_SHIFT)
+#define PIN_DIR_OUTPUT (1 << PIN_DIR_SHIFT)
+
+#define PIN_VAL_SHIFT 15
+#define PIN_VAL_MASK (0x1 << PIN_VAL_SHIFT)
+#define PIN_VAL(x) (((x) & PIN_VAL_MASK) >> PIN_VAL_SHIFT)
+#define PIN_VAL_LOW (0 << PIN_VAL_SHIFT)
+#define PIN_VAL_HIGH (1 << PIN_VAL_SHIFT)
+
+#define PIN_SLPM_PULL_SHIFT 16
+#define PIN_SLPM_PULL_MASK (0x7 << PIN_SLPM_PULL_SHIFT)
+#define PIN_SLPM_PULL(x) \
+ (((x) & PIN_SLPM_PULL_MASK) >> PIN_SLPM_PULL_SHIFT)
+#define PIN_SLPM_PULL_NONE \
+ ((1 + NMK_GPIO_PULL_NONE) << PIN_SLPM_PULL_SHIFT)
+#define PIN_SLPM_PULL_UP \
+ ((1 + NMK_GPIO_PULL_UP) << PIN_SLPM_PULL_SHIFT)
+#define PIN_SLPM_PULL_DOWN \
+ ((1 + NMK_GPIO_PULL_DOWN) << PIN_SLPM_PULL_SHIFT)
+
+#define PIN_SLPM_DIR_SHIFT 19
+#define PIN_SLPM_DIR_MASK (0x3 << PIN_SLPM_DIR_SHIFT)
+#define PIN_SLPM_DIR(x) \
+ (((x) & PIN_SLPM_DIR_MASK) >> PIN_SLPM_DIR_SHIFT)
+#define PIN_SLPM_DIR_INPUT ((1 + 0) << PIN_SLPM_DIR_SHIFT)
+#define PIN_SLPM_DIR_OUTPUT ((1 + 1) << PIN_SLPM_DIR_SHIFT)
+
+#define PIN_SLPM_VAL_SHIFT 21
+#define PIN_SLPM_VAL_MASK (0x3 << PIN_SLPM_VAL_SHIFT)
+#define PIN_SLPM_VAL(x) \
+ (((x) & PIN_SLPM_VAL_MASK) >> PIN_SLPM_VAL_SHIFT)
+#define PIN_SLPM_VAL_LOW ((1 + 0) << PIN_SLPM_VAL_SHIFT)
+#define PIN_SLPM_VAL_HIGH ((1 + 1) << PIN_SLPM_VAL_SHIFT)
+
+#define PIN_SLPM_PDIS_SHIFT 23
+#define PIN_SLPM_PDIS_MASK (0x3 << PIN_SLPM_PDIS_SHIFT)
+#define PIN_SLPM_PDIS(x) \
+ (((x) & PIN_SLPM_PDIS_MASK) >> PIN_SLPM_PDIS_SHIFT)
+#define PIN_SLPM_PDIS_NO_CHANGE (0 << PIN_SLPM_PDIS_SHIFT)
+#define PIN_SLPM_PDIS_DISABLED (1 << PIN_SLPM_PDIS_SHIFT)
+#define PIN_SLPM_PDIS_ENABLED (2 << PIN_SLPM_PDIS_SHIFT)
+
+#define PIN_LOWEMI_SHIFT 25
+#define PIN_LOWEMI_MASK (0x1 << PIN_LOWEMI_SHIFT)
+#define PIN_LOWEMI(x) (((x) & PIN_LOWEMI_MASK) >> PIN_LOWEMI_SHIFT)
+#define PIN_LOWEMI_DISABLED (0 << PIN_LOWEMI_SHIFT)
+#define PIN_LOWEMI_ENABLED (1 << PIN_LOWEMI_SHIFT)
+
+#define PIN_GPIOMODE_SHIFT 26
+#define PIN_GPIOMODE_MASK (0x1 << PIN_GPIOMODE_SHIFT)
+#define PIN_GPIOMODE(x) (((x) & PIN_GPIOMODE_MASK) >> PIN_GPIOMODE_SHIFT)
+#define PIN_GPIOMODE_DISABLED (0 << PIN_GPIOMODE_SHIFT)
+#define PIN_GPIOMODE_ENABLED (1 << PIN_GPIOMODE_SHIFT)
+
+#define PIN_SLEEPMODE_SHIFT 27
+#define PIN_SLEEPMODE_MASK (0x1 << PIN_SLEEPMODE_SHIFT)
+#define PIN_SLEEPMODE(x) (((x) & PIN_SLEEPMODE_MASK) >> PIN_SLEEPMODE_SHIFT)
+#define PIN_SLEEPMODE_DISABLED (0 << PIN_SLEEPMODE_SHIFT)
+#define PIN_SLEEPMODE_ENABLED (1 << PIN_SLEEPMODE_SHIFT)
+
+
+/* Shortcuts. Use these instead of separate DIR, PULL, and VAL. */
+#define PIN_INPUT_PULLDOWN (PIN_DIR_INPUT | PIN_PULL_DOWN)
+#define PIN_INPUT_PULLUP (PIN_DIR_INPUT | PIN_PULL_UP)
+#define PIN_INPUT_NOPULL (PIN_DIR_INPUT | PIN_PULL_NONE)
+#define PIN_OUTPUT_LOW (PIN_DIR_OUTPUT | PIN_VAL_LOW)
+#define PIN_OUTPUT_HIGH (PIN_DIR_OUTPUT | PIN_VAL_HIGH)
+
+#define PIN_SLPM_INPUT_PULLDOWN (PIN_SLPM_DIR_INPUT | PIN_SLPM_PULL_DOWN)
+#define PIN_SLPM_INPUT_PULLUP (PIN_SLPM_DIR_INPUT | PIN_SLPM_PULL_UP)
+#define PIN_SLPM_INPUT_NOPULL (PIN_SLPM_DIR_INPUT | PIN_SLPM_PULL_NONE)
+#define PIN_SLPM_OUTPUT_LOW (PIN_SLPM_DIR_OUTPUT | PIN_SLPM_VAL_LOW)
+#define PIN_SLPM_OUTPUT_HIGH (PIN_SLPM_DIR_OUTPUT | PIN_SLPM_VAL_HIGH)
+
+#define PIN_CFG_DEFAULT (0)
+
+#define PIN_CFG(num, alt) \
+ (PIN_CFG_DEFAULT |\
+ (PIN_NUM(num) | PIN_##alt))
+
+#define PIN_CFG_INPUT(num, alt, pull) \
+ (PIN_CFG_DEFAULT |\
+ (PIN_NUM(num) | PIN_##alt | PIN_INPUT_##pull))
+
+#define PIN_CFG_OUTPUT(num, alt, val) \
+ (PIN_CFG_DEFAULT |\
+ (PIN_NUM(num) | PIN_##alt | PIN_OUTPUT_##val))
+
+/*
+ * "nmk_gpio" and "NMK_GPIO" stand for "Nomadik GPIO", leaving
+ * the "gpio" namespace for generic and cross-machine functions
+ */
+
+#define GPIO_BLOCK_SHIFT 5
+#define NMK_GPIO_PER_CHIP (1 << GPIO_BLOCK_SHIFT)
+
+/* Register in the logic block */
+#define NMK_GPIO_DAT 0x00
+#define NMK_GPIO_DATS 0x04
+#define NMK_GPIO_DATC 0x08
+#define NMK_GPIO_PDIS 0x0c
+#define NMK_GPIO_DIR 0x10
+#define NMK_GPIO_DIRS 0x14
+#define NMK_GPIO_DIRC 0x18
+#define NMK_GPIO_SLPC 0x1c
+#define NMK_GPIO_AFSLA 0x20
+#define NMK_GPIO_AFSLB 0x24
+#define NMK_GPIO_LOWEMI 0x28
+
+#define NMK_GPIO_RIMSC 0x40
+#define NMK_GPIO_FIMSC 0x44
+#define NMK_GPIO_IS 0x48
+#define NMK_GPIO_IC 0x4c
+#define NMK_GPIO_RWIMSC 0x50
+#define NMK_GPIO_FWIMSC 0x54
+#define NMK_GPIO_WKS 0x58
+/* These appear in DB8540 and later ASICs */
+#define NMK_GPIO_EDGELEVEL 0x5C
+#define NMK_GPIO_LEVEL 0x60
+
+
+/* Pull up/down values */
+enum nmk_gpio_pull {
+ NMK_GPIO_PULL_NONE,
+ NMK_GPIO_PULL_UP,
+ NMK_GPIO_PULL_DOWN,
+};
+
+/* Sleep mode */
+enum nmk_gpio_slpm {
+ NMK_GPIO_SLPM_INPUT,
+ NMK_GPIO_SLPM_WAKEUP_ENABLE = NMK_GPIO_SLPM_INPUT,
+ NMK_GPIO_SLPM_NOCHANGE,
+ NMK_GPIO_SLPM_WAKEUP_DISABLE = NMK_GPIO_SLPM_NOCHANGE,
+};
+
+/*
+ * Platform data to register a block: only the initial gpio/irq number.
+ */
+struct nmk_gpio_platform_data {
+ char *name;
+ int first_gpio;
+ int first_irq;
+ int num_gpio;
+ u32 (*get_secondary_status)(unsigned int bank);
+ void (*set_ioforce)(bool enable);
+ bool supports_sleepmode;
+};
+
struct nmk_gpio_chip {
struct gpio_chip chip;
struct irq_domain *domain;
static int nmk_gpio_probe(struct platform_device *dev)
{
- struct nmk_gpio_platform_data *pdata = dev->dev.platform_data;
+ struct nmk_gpio_platform_data *pdata;
struct device_node *np = dev->dev.of_node;
struct nmk_gpio_chip *nmk_chip;
struct gpio_chip *chip;
struct clk *clk;
int secondary_irq;
void __iomem *base;
- int irq_start = 0;
int irq;
int ret;
- if (!pdata && !np) {
- dev_err(&dev->dev, "No platform data or device tree found\n");
- return -ENODEV;
- }
-
- if (np) {
- pdata = devm_kzalloc(&dev->dev, sizeof(*pdata), GFP_KERNEL);
- if (!pdata)
- return -ENOMEM;
-
- if (of_get_property(np, "st,supports-sleepmode", NULL))
- pdata->supports_sleepmode = true;
+ pdata = devm_kzalloc(&dev->dev, sizeof(*pdata), GFP_KERNEL);
+ if (!pdata)
+ return -ENOMEM;
- if (of_property_read_u32(np, "gpio-bank", &dev->id)) {
- dev_err(&dev->dev, "gpio-bank property not found\n");
- return -EINVAL;
- }
+ if (of_get_property(np, "st,supports-sleepmode", NULL))
+ pdata->supports_sleepmode = true;
- pdata->first_gpio = dev->id * NMK_GPIO_PER_CHIP;
- pdata->num_gpio = NMK_GPIO_PER_CHIP;
+ if (of_property_read_u32(np, "gpio-bank", &dev->id)) {
+ dev_err(&dev->dev, "gpio-bank property not found\n");
+ return -EINVAL;
}
+ pdata->first_gpio = dev->id * NMK_GPIO_PER_CHIP;
+ pdata->num_gpio = NMK_GPIO_PER_CHIP;
+
irq = platform_get_irq(dev, 0);
if (irq < 0)
return irq;
clk_enable(nmk_chip->clk);
nmk_chip->lowemi = readl_relaxed(nmk_chip->addr + NMK_GPIO_LOWEMI);
clk_disable(nmk_chip->clk);
-
-#ifdef CONFIG_OF_GPIO
chip->of_node = np;
-#endif
ret = gpiochip_add(&nmk_chip->chip);
if (ret)
platform_set_drvdata(dev, nmk_chip);
- if (!np)
- irq_start = pdata->first_irq;
nmk_chip->domain = irq_domain_add_simple(np,
- NMK_GPIO_PER_CHIP, irq_start,
+ NMK_GPIO_PER_CHIP, 0,
&nmk_gpio_irq_simple_ops, nmk_chip);
if (!nmk_chip->domain) {
dev_err(&dev->dev, "failed to create irqdomain\n");
static int nmk_pinctrl_probe(struct platform_device *pdev)
{
- const struct platform_device_id *platid = platform_get_device_id(pdev);
+ const struct of_device_id *match;
struct device_node *np = pdev->dev.of_node;
struct device_node *prcm_np;
struct nmk_pinctrl *npct;
- struct resource *res;
unsigned int version = 0;
int i;
if (!npct)
return -ENOMEM;
- if (platid)
- version = platid->driver_data;
- else if (np) {
- const struct of_device_id *match;
-
- match = of_match_device(nmk_pinctrl_match, &pdev->dev);
- if (!match)
- return -ENODEV;
- version = (unsigned int) match->data;
- }
+ match = of_match_device(nmk_pinctrl_match, &pdev->dev);
+ if (!match)
+ return -ENODEV;
+ version = (unsigned int) match->data;
/* Poke in other ASIC variants here */
if (version == PINCTRL_NMK_STN8815)
if (version == PINCTRL_NMK_DB8540)
nmk_pinctrl_db8540_init(&npct->soc);
- if (np) {
- prcm_np = of_parse_phandle(np, "prcm", 0);
- if (prcm_np)
- npct->prcm_base = of_iomap(prcm_np, 0);
- }
-
- /* Allow platform passed information to over-write DT. */
- res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- if (res)
- npct->prcm_base = devm_ioremap(&pdev->dev, res->start,
- resource_size(res));
+ prcm_np = of_parse_phandle(np, "prcm", 0);
+ if (prcm_np)
+ npct->prcm_base = of_iomap(prcm_np, 0);
if (!npct->prcm_base) {
if (version == PINCTRL_NMK_STN8815) {
dev_info(&pdev->dev,
.probe = nmk_gpio_probe,
};
-static const struct platform_device_id nmk_pinctrl_id[] = {
- { "pinctrl-stn8815", PINCTRL_NMK_STN8815 },
- { "pinctrl-db8500", PINCTRL_NMK_DB8500 },
- { "pinctrl-db8540", PINCTRL_NMK_DB8540 },
- { }
-};
-
static struct platform_driver nmk_pinctrl_driver = {
.driver = {
.owner = THIS_MODULE,
.of_match_table = nmk_pinctrl_match,
},
.probe = nmk_pinctrl_probe,
- .id_table = nmk_pinctrl_id,
#ifdef CONFIG_PM
.suspend = nmk_pinctrl_suspend,
.resume = nmk_pinctrl_resume,
#ifndef PINCTRL_PINCTRL_NOMADIK_H
#define PINCTRL_PINCTRL_NOMADIK_H
-#include <linux/platform_data/pinctrl-nomadik.h>
-
/* Package definitions */
#define PINCTRL_NMK_STN8815 0
#define PINCTRL_NMK_DB8500 1
#define PINCTRL_NMK_DB8540 2
+/* Alternate functions: function C is set in hw by setting both A and B */
+#define NMK_GPIO_ALT_GPIO 0
+#define NMK_GPIO_ALT_A 1
+#define NMK_GPIO_ALT_B 2
+#define NMK_GPIO_ALT_C (NMK_GPIO_ALT_A | NMK_GPIO_ALT_B)
+
+#define NMK_GPIO_ALT_CX_SHIFT 2
+#define NMK_GPIO_ALT_C1 ((1<<NMK_GPIO_ALT_CX_SHIFT) | NMK_GPIO_ALT_C)
+#define NMK_GPIO_ALT_C2 ((2<<NMK_GPIO_ALT_CX_SHIFT) | NMK_GPIO_ALT_C)
+#define NMK_GPIO_ALT_C3 ((3<<NMK_GPIO_ALT_CX_SHIFT) | NMK_GPIO_ALT_C)
+#define NMK_GPIO_ALT_C4 ((4<<NMK_GPIO_ALT_CX_SHIFT) | NMK_GPIO_ALT_C)
+
#define PRCM_GPIOCR_ALTCX(pin_num,\
altc1_used, altc1_ri, altc1_cb,\
altc2_used, altc2_ri, altc2_cb,\
+++ /dev/null
-#ifndef __PLAT_MTU_H
-#define __PLAT_MTU_H
-
-void nmdk_timer_init(void __iomem *base, int irq);
-void nmdk_clkevt_reset(void);
-void nmdk_clksrc_reset(void);
-
-#endif /* __PLAT_MTU_H */
-
+++ /dev/null
-/*
- * Structures and registers for GPIO access in the Nomadik SoC
- *
- * Copyright (C) 2008 STMicroelectronics
- * Author: Prafulla WADASKAR <prafulla.wadaskar@st.com>
- * Copyright (C) 2009 Alessandro Rubini <rubini@unipv.it>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __PLAT_NOMADIK_GPIO
-#define __PLAT_NOMADIK_GPIO
-
-/*
- * pin configurations are represented by 32-bit integers:
- *
- * bit 0.. 8 - Pin Number (512 Pins Maximum)
- * bit 9..10 - Alternate Function Selection
- * bit 11..12 - Pull up/down state
- * bit 13 - Sleep mode behaviour
- * bit 14 - Direction
- * bit 15 - Value (if output)
- * bit 16..18 - SLPM pull up/down state
- * bit 19..20 - SLPM direction
- * bit 21..22 - SLPM Value (if output)
- * bit 23..25 - PDIS value (if input)
- * bit 26 - Gpio mode
- * bit 27 - Sleep mode
- *
- * to facilitate the definition, the following macros are provided
- *
- * PIN_CFG_DEFAULT - default config (0):
- * pull up/down = disabled
- * sleep mode = input/wakeup
- * direction = input
- * value = low
- * SLPM direction = same as normal
- * SLPM pull = same as normal
- * SLPM value = same as normal
- *
- * PIN_CFG - default config with alternate function
- */
-
-typedef unsigned long pin_cfg_t;
-
-#define PIN_NUM_MASK 0x1ff
-#define PIN_NUM(x) ((x) & PIN_NUM_MASK)
-
-#define PIN_ALT_SHIFT 9
-#define PIN_ALT_MASK (0x3 << PIN_ALT_SHIFT)
-#define PIN_ALT(x) (((x) & PIN_ALT_MASK) >> PIN_ALT_SHIFT)
-#define PIN_GPIO (NMK_GPIO_ALT_GPIO << PIN_ALT_SHIFT)
-#define PIN_ALT_A (NMK_GPIO_ALT_A << PIN_ALT_SHIFT)
-#define PIN_ALT_B (NMK_GPIO_ALT_B << PIN_ALT_SHIFT)
-#define PIN_ALT_C (NMK_GPIO_ALT_C << PIN_ALT_SHIFT)
-
-#define PIN_PULL_SHIFT 11
-#define PIN_PULL_MASK (0x3 << PIN_PULL_SHIFT)
-#define PIN_PULL(x) (((x) & PIN_PULL_MASK) >> PIN_PULL_SHIFT)
-#define PIN_PULL_NONE (NMK_GPIO_PULL_NONE << PIN_PULL_SHIFT)
-#define PIN_PULL_UP (NMK_GPIO_PULL_UP << PIN_PULL_SHIFT)
-#define PIN_PULL_DOWN (NMK_GPIO_PULL_DOWN << PIN_PULL_SHIFT)
-
-#define PIN_SLPM_SHIFT 13
-#define PIN_SLPM_MASK (0x1 << PIN_SLPM_SHIFT)
-#define PIN_SLPM(x) (((x) & PIN_SLPM_MASK) >> PIN_SLPM_SHIFT)
-#define PIN_SLPM_MAKE_INPUT (NMK_GPIO_SLPM_INPUT << PIN_SLPM_SHIFT)
-#define PIN_SLPM_NOCHANGE (NMK_GPIO_SLPM_NOCHANGE << PIN_SLPM_SHIFT)
-/* These two replace the above in DB8500v2+ */
-#define PIN_SLPM_WAKEUP_ENABLE (NMK_GPIO_SLPM_WAKEUP_ENABLE << PIN_SLPM_SHIFT)
-#define PIN_SLPM_WAKEUP_DISABLE (NMK_GPIO_SLPM_WAKEUP_DISABLE << PIN_SLPM_SHIFT)
-#define PIN_SLPM_USE_MUX_SETTINGS_IN_SLEEP PIN_SLPM_WAKEUP_DISABLE
-
-#define PIN_SLPM_GPIO PIN_SLPM_WAKEUP_ENABLE /* In SLPM, pin is a gpio */
-#define PIN_SLPM_ALTFUNC PIN_SLPM_WAKEUP_DISABLE /* In SLPM, pin is altfunc */
-
-#define PIN_DIR_SHIFT 14
-#define PIN_DIR_MASK (0x1 << PIN_DIR_SHIFT)
-#define PIN_DIR(x) (((x) & PIN_DIR_MASK) >> PIN_DIR_SHIFT)
-#define PIN_DIR_INPUT (0 << PIN_DIR_SHIFT)
-#define PIN_DIR_OUTPUT (1 << PIN_DIR_SHIFT)
-
-#define PIN_VAL_SHIFT 15
-#define PIN_VAL_MASK (0x1 << PIN_VAL_SHIFT)
-#define PIN_VAL(x) (((x) & PIN_VAL_MASK) >> PIN_VAL_SHIFT)
-#define PIN_VAL_LOW (0 << PIN_VAL_SHIFT)
-#define PIN_VAL_HIGH (1 << PIN_VAL_SHIFT)
-
-#define PIN_SLPM_PULL_SHIFT 16
-#define PIN_SLPM_PULL_MASK (0x7 << PIN_SLPM_PULL_SHIFT)
-#define PIN_SLPM_PULL(x) \
- (((x) & PIN_SLPM_PULL_MASK) >> PIN_SLPM_PULL_SHIFT)
-#define PIN_SLPM_PULL_NONE \
- ((1 + NMK_GPIO_PULL_NONE) << PIN_SLPM_PULL_SHIFT)
-#define PIN_SLPM_PULL_UP \
- ((1 + NMK_GPIO_PULL_UP) << PIN_SLPM_PULL_SHIFT)
-#define PIN_SLPM_PULL_DOWN \
- ((1 + NMK_GPIO_PULL_DOWN) << PIN_SLPM_PULL_SHIFT)
-
-#define PIN_SLPM_DIR_SHIFT 19
-#define PIN_SLPM_DIR_MASK (0x3 << PIN_SLPM_DIR_SHIFT)
-#define PIN_SLPM_DIR(x) \
- (((x) & PIN_SLPM_DIR_MASK) >> PIN_SLPM_DIR_SHIFT)
-#define PIN_SLPM_DIR_INPUT ((1 + 0) << PIN_SLPM_DIR_SHIFT)
-#define PIN_SLPM_DIR_OUTPUT ((1 + 1) << PIN_SLPM_DIR_SHIFT)
-
-#define PIN_SLPM_VAL_SHIFT 21
-#define PIN_SLPM_VAL_MASK (0x3 << PIN_SLPM_VAL_SHIFT)
-#define PIN_SLPM_VAL(x) \
- (((x) & PIN_SLPM_VAL_MASK) >> PIN_SLPM_VAL_SHIFT)
-#define PIN_SLPM_VAL_LOW ((1 + 0) << PIN_SLPM_VAL_SHIFT)
-#define PIN_SLPM_VAL_HIGH ((1 + 1) << PIN_SLPM_VAL_SHIFT)
-
-#define PIN_SLPM_PDIS_SHIFT 23
-#define PIN_SLPM_PDIS_MASK (0x3 << PIN_SLPM_PDIS_SHIFT)
-#define PIN_SLPM_PDIS(x) \
- (((x) & PIN_SLPM_PDIS_MASK) >> PIN_SLPM_PDIS_SHIFT)
-#define PIN_SLPM_PDIS_NO_CHANGE (0 << PIN_SLPM_PDIS_SHIFT)
-#define PIN_SLPM_PDIS_DISABLED (1 << PIN_SLPM_PDIS_SHIFT)
-#define PIN_SLPM_PDIS_ENABLED (2 << PIN_SLPM_PDIS_SHIFT)
-
-#define PIN_LOWEMI_SHIFT 25
-#define PIN_LOWEMI_MASK (0x1 << PIN_LOWEMI_SHIFT)
-#define PIN_LOWEMI(x) (((x) & PIN_LOWEMI_MASK) >> PIN_LOWEMI_SHIFT)
-#define PIN_LOWEMI_DISABLED (0 << PIN_LOWEMI_SHIFT)
-#define PIN_LOWEMI_ENABLED (1 << PIN_LOWEMI_SHIFT)
-
-#define PIN_GPIOMODE_SHIFT 26
-#define PIN_GPIOMODE_MASK (0x1 << PIN_GPIOMODE_SHIFT)
-#define PIN_GPIOMODE(x) (((x) & PIN_GPIOMODE_MASK) >> PIN_GPIOMODE_SHIFT)
-#define PIN_GPIOMODE_DISABLED (0 << PIN_GPIOMODE_SHIFT)
-#define PIN_GPIOMODE_ENABLED (1 << PIN_GPIOMODE_SHIFT)
-
-#define PIN_SLEEPMODE_SHIFT 27
-#define PIN_SLEEPMODE_MASK (0x1 << PIN_SLEEPMODE_SHIFT)
-#define PIN_SLEEPMODE(x) (((x) & PIN_SLEEPMODE_MASK) >> PIN_SLEEPMODE_SHIFT)
-#define PIN_SLEEPMODE_DISABLED (0 << PIN_SLEEPMODE_SHIFT)
-#define PIN_SLEEPMODE_ENABLED (1 << PIN_SLEEPMODE_SHIFT)
-
-
-/* Shortcuts. Use these instead of separate DIR, PULL, and VAL. */
-#define PIN_INPUT_PULLDOWN (PIN_DIR_INPUT | PIN_PULL_DOWN)
-#define PIN_INPUT_PULLUP (PIN_DIR_INPUT | PIN_PULL_UP)
-#define PIN_INPUT_NOPULL (PIN_DIR_INPUT | PIN_PULL_NONE)
-#define PIN_OUTPUT_LOW (PIN_DIR_OUTPUT | PIN_VAL_LOW)
-#define PIN_OUTPUT_HIGH (PIN_DIR_OUTPUT | PIN_VAL_HIGH)
-
-#define PIN_SLPM_INPUT_PULLDOWN (PIN_SLPM_DIR_INPUT | PIN_SLPM_PULL_DOWN)
-#define PIN_SLPM_INPUT_PULLUP (PIN_SLPM_DIR_INPUT | PIN_SLPM_PULL_UP)
-#define PIN_SLPM_INPUT_NOPULL (PIN_SLPM_DIR_INPUT | PIN_SLPM_PULL_NONE)
-#define PIN_SLPM_OUTPUT_LOW (PIN_SLPM_DIR_OUTPUT | PIN_SLPM_VAL_LOW)
-#define PIN_SLPM_OUTPUT_HIGH (PIN_SLPM_DIR_OUTPUT | PIN_SLPM_VAL_HIGH)
-
-#define PIN_CFG_DEFAULT (0)
-
-#define PIN_CFG(num, alt) \
- (PIN_CFG_DEFAULT |\
- (PIN_NUM(num) | PIN_##alt))
-
-#define PIN_CFG_INPUT(num, alt, pull) \
- (PIN_CFG_DEFAULT |\
- (PIN_NUM(num) | PIN_##alt | PIN_INPUT_##pull))
-
-#define PIN_CFG_OUTPUT(num, alt, val) \
- (PIN_CFG_DEFAULT |\
- (PIN_NUM(num) | PIN_##alt | PIN_OUTPUT_##val))
-
-/*
- * "nmk_gpio" and "NMK_GPIO" stand for "Nomadik GPIO", leaving
- * the "gpio" namespace for generic and cross-machine functions
- */
-
-#define GPIO_BLOCK_SHIFT 5
-#define NMK_GPIO_PER_CHIP (1 << GPIO_BLOCK_SHIFT)
-
-/* Register in the logic block */
-#define NMK_GPIO_DAT 0x00
-#define NMK_GPIO_DATS 0x04
-#define NMK_GPIO_DATC 0x08
-#define NMK_GPIO_PDIS 0x0c
-#define NMK_GPIO_DIR 0x10
-#define NMK_GPIO_DIRS 0x14
-#define NMK_GPIO_DIRC 0x18
-#define NMK_GPIO_SLPC 0x1c
-#define NMK_GPIO_AFSLA 0x20
-#define NMK_GPIO_AFSLB 0x24
-#define NMK_GPIO_LOWEMI 0x28
-
-#define NMK_GPIO_RIMSC 0x40
-#define NMK_GPIO_FIMSC 0x44
-#define NMK_GPIO_IS 0x48
-#define NMK_GPIO_IC 0x4c
-#define NMK_GPIO_RWIMSC 0x50
-#define NMK_GPIO_FWIMSC 0x54
-#define NMK_GPIO_WKS 0x58
-/* These appear in DB8540 and later ASICs */
-#define NMK_GPIO_EDGELEVEL 0x5C
-#define NMK_GPIO_LEVEL 0x60
-
-/* Alternate functions: function C is set in hw by setting both A and B */
-#define NMK_GPIO_ALT_GPIO 0
-#define NMK_GPIO_ALT_A 1
-#define NMK_GPIO_ALT_B 2
-#define NMK_GPIO_ALT_C (NMK_GPIO_ALT_A | NMK_GPIO_ALT_B)
-
-#define NMK_GPIO_ALT_CX_SHIFT 2
-#define NMK_GPIO_ALT_C1 ((1<<NMK_GPIO_ALT_CX_SHIFT) | NMK_GPIO_ALT_C)
-#define NMK_GPIO_ALT_C2 ((2<<NMK_GPIO_ALT_CX_SHIFT) | NMK_GPIO_ALT_C)
-#define NMK_GPIO_ALT_C3 ((3<<NMK_GPIO_ALT_CX_SHIFT) | NMK_GPIO_ALT_C)
-#define NMK_GPIO_ALT_C4 ((4<<NMK_GPIO_ALT_CX_SHIFT) | NMK_GPIO_ALT_C)
-
-/* Pull up/down values */
-enum nmk_gpio_pull {
- NMK_GPIO_PULL_NONE,
- NMK_GPIO_PULL_UP,
- NMK_GPIO_PULL_DOWN,
-};
-
-/* Sleep mode */
-enum nmk_gpio_slpm {
- NMK_GPIO_SLPM_INPUT,
- NMK_GPIO_SLPM_WAKEUP_ENABLE = NMK_GPIO_SLPM_INPUT,
- NMK_GPIO_SLPM_NOCHANGE,
- NMK_GPIO_SLPM_WAKEUP_DISABLE = NMK_GPIO_SLPM_NOCHANGE,
-};
-
-/*
- * Platform data to register a block: only the initial gpio/irq number.
- */
-struct nmk_gpio_platform_data {
- char *name;
- int first_gpio;
- int first_irq;
- int num_gpio;
- u32 (*get_secondary_status)(unsigned int bank);
- void (*set_ioforce)(bool enable);
- bool supports_sleepmode;
-};
-
-#endif /* __PLAT_NOMADIK_GPIO */
projects / ~andy / linux / commitdiff