- compatible: Should be "cdns,[<chip>-]{macb|gem}"
Use "cdns,at91sam9260-macb" Atmel at91sam9260 and at91sam9263 SoCs.
Use "cdns,at32ap7000-macb" for other 10/100 usage or use the generic form: "cdns,macb".
- Use "cnds,pc302-gem" for Picochip picoXcell pc302 and later devices based on
+ Use "cdns,pc302-gem" for Picochip picoXcell pc302 and later devices based on
the Cadence GEM, or the generic form: "cdns,gem".
- reg: Address and length of the register set for the device
- interrupts: Should contain macb interrupt
--- /dev/null
+Simple Framebuffer
+
+A simple frame-buffer describes a raw memory region that may be rendered to,
+with the assumption that the display hardware has already been set up to scan
+out from that buffer.
+
+Required properties:
+- compatible: "simple-framebuffer"
+- reg: Should contain the location and size of the framebuffer memory.
+- width: The width of the framebuffer in pixels.
+- height: The height of the framebuffer in pixels.
+- stride: The number of bytes in each line of the framebuffer.
+- format: The format of the framebuffer surface. Valid values are:
+ - r5g6b5 (16-bit pixels, d[15:11]=r, d[10:5]=g, d[4:0]=b).
+
+Example:
+
+ framebuffer {
+ compatible = "simple-framebuffer";
+ reg = <0x1d385000 (1600 * 1200 * 2)>;
+ width = <1600>;
+ height = <1200>;
+ stride = <(1600 * 2)>;
+ format = "r5g6b5";
+ };
After a while you will start to get messages about current status or error like
in the original code.
-Note that running a new test will stop any in progress test.
+Note that running a new test will not stop any in progress test.
The following command should return actual state of the test.
% cat /sys/kernel/debug/dmatest/run
The module parameters that is supplied to the kernel command line will be used
for the first performed test. After user gets a control, the test could be
-interrupted or re-run with same or different parameters. For the details see
-the above section "Part 2 - When dmatest is built as a module..."
+re-run with the same or different parameters. For the details see the above
+section "Part 2 - When dmatest is built as a module..."
In both cases the module parameters are used as initial values for the test case.
You always could check them at run-time by running
removing extended attributes) the on-disk superblock feature
bit field will be updated to reflect this format being in use.
+ CRC enabled filesystems always use the attr2 format, and so
+ will reject the noattr2 mount option if it is set.
+
barrier
Enables the use of block layer write barriers for writes into
the journal and unwritten extent conversion. This allows for
fix_the_problem(ucp->dar);
}
+When in an active transaction that takes a signal, we need to be careful with
+the stack. It's possible that the stack has moved back up after the tbegin.
+The obvious case here is when the tbegin is called inside a function that
+returns before a tend. In this case, the stack is part of the checkpointed
+transactional memory state. If we write over this non transactionally or in
+suspend, we are in trouble because if we get a tm abort, the program counter and
+stack pointer will be back at the tbegin but our in memory stack won't be valid
+anymore.
+
+To avoid this, when taking a signal in an active transaction, we need to use
+the stack pointer from the checkpointed state, rather than the speculated
+state. This ensures that the signal context (written tm suspended) will be
+written below the stack required for the rollback. The transaction is aborted
+becuase of the treclaim, so any memory written between the tbegin and the
+signal will be rolled back anyway.
+
+For signals taken in non-TM or suspended mode, we use the
+normal/non-checkpointed stack pointer.
+
Failure cause codes used by kernel
==================================
kernel aborted a transaction:
TM_CAUSE_RESCHED Thread was rescheduled.
+ TM_CAUSE_TLBI Software TLB invalide.
TM_CAUSE_FAC_UNAV FP/VEC/VSX unavailable trap.
TM_CAUSE_SYSCALL Currently unused; future syscalls that must abort
transactions for consistency will use this.
TM_CAUSE_SIGNAL Signal delivered.
TM_CAUSE_MISC Currently unused.
+ TM_CAUSE_ALIGNMENT Alignment fault.
+ TM_CAUSE_EMULATE Emulation that touched memory.
-These can be checked by the user program's abort handler as TEXASR[0:7].
-
+These can be checked by the user program's abort handler as TEXASR[0:7]. If
+bit 7 is set, it indicates that the error is consider persistent. For example
+a TM_CAUSE_ALIGNMENT will be persistent while a TM_CAUSE_RESCHED will not.q
GDB
===
In order to initialize the RapidIO subsystem, a platform must initialize and
register at least one master port within the RapidIO network. To register mport
within the subsystem controller driver initialization code calls function
-rio_register_mport() for each available master port. After all active master
-ports are registered with a RapidIO subsystem, the rio_init_mports() routine
-is called to perform enumeration and discovery.
+rio_register_mport() for each available master port.
-In the current PowerPC-based implementation a subsys_initcall() is specified to
-perform controller initialization and mport registration. At the end it directly
-calls rio_init_mports() to execute RapidIO enumeration and discovery.
+RapidIO subsystem uses subsys_initcall() or device_initcall() to perform
+controller initialization (depending on controller device type).
+
+After all active master ports are registered with a RapidIO subsystem,
+an enumeration and/or discovery routine may be called automatically or
+by user-space command.
4. Enumeration and Discovery
----------------------------
-When rio_init_mports() is called it scans a list of registered master ports and
-calls an enumeration or discovery routine depending on the configured role of a
-master port: host or agent.
+4.1 Overview
+------------
+
+RapidIO subsystem configuration options allow users to specify enumeration and
+discovery methods as statically linked components or loadable modules.
+An enumeration/discovery method implementation and available input parameters
+define how any given method can be attached to available RapidIO mports:
+simply to all available mports OR individually to the specified mport device.
+
+Depending on selected enumeration/discovery build configuration, there are
+several methods to initiate an enumeration and/or discovery process:
+
+ (a) Statically linked enumeration and discovery process can be started
+ automatically during kernel initialization time using corresponding module
+ parameters. This was the original method used since introduction of RapidIO
+ subsystem. Now this method relies on enumerator module parameter which is
+ 'rio-scan.scan' for existing basic enumeration/discovery method.
+ When automatic start of enumeration/discovery is used a user has to ensure
+ that all discovering endpoints are started before the enumerating endpoint
+ and are waiting for enumeration to be completed.
+ Configuration option CONFIG_RAPIDIO_DISC_TIMEOUT defines time that discovering
+ endpoint waits for enumeration to be completed. If the specified timeout
+ expires the discovery process is terminated without obtaining RapidIO network
+ information. NOTE: a timed out discovery process may be restarted later using
+ a user-space command as it is described later if the given endpoint was
+ enumerated successfully.
+
+ (b) Statically linked enumeration and discovery process can be started by
+ a command from user space. This initiation method provides more flexibility
+ for a system startup compared to the option (a) above. After all participating
+ endpoints have been successfully booted, an enumeration process shall be
+ started first by issuing a user-space command, after an enumeration is
+ completed a discovery process can be started on all remaining endpoints.
+
+ (c) Modular enumeration and discovery process can be started by a command from
+ user space. After an enumeration/discovery module is loaded, a network scan
+ process can be started by issuing a user-space command.
+ Similar to the option (b) above, an enumerator has to be started first.
+
+ (d) Modular enumeration and discovery process can be started by a module
+ initialization routine. In this case an enumerating module shall be loaded
+ first.
+
+When a network scan process is started it calls an enumeration or discovery
+routine depending on the configured role of a master port: host or agent.
Enumeration is performed by a master port if it is configured as a host port by
assigning a host device ID greater than or equal to zero. A host device ID is
The enumeration and discovery routines use RapidIO maintenance transactions
to access the configuration space of devices.
-The enumeration process is implemented according to the enumeration algorithm
-outlined in the RapidIO Interconnect Specification: Annex I [1].
+4.2 Automatic Start of Enumeration and Discovery
+------------------------------------------------
+
+Automatic enumeration/discovery start method is applicable only to built-in
+enumeration/discovery RapidIO configuration selection. To enable automatic
+enumeration/discovery start by existing basic enumerator method set use boot
+command line parameter "rio-scan.scan=1".
+
+This configuration requires synchronized start of all RapidIO endpoints that
+form a network which will be enumerated/discovered. Discovering endpoints have
+to be started before an enumeration starts to ensure that all RapidIO
+controllers have been initialized and are ready to be discovered. Configuration
+parameter CONFIG_RAPIDIO_DISC_TIMEOUT defines time (in seconds) which
+a discovering endpoint will wait for enumeration to be completed.
+
+When automatic enumeration/discovery start is selected, basic method's
+initialization routine calls rio_init_mports() to perform enumeration or
+discovery for all known mport devices.
+
+Depending on RapidIO network size and configuration this automatic
+enumeration/discovery start method may be difficult to use due to the
+requirement for synchronized start of all endpoints.
+
+4.3 User-space Start of Enumeration and Discovery
+-------------------------------------------------
+
+User-space start of enumeration and discovery can be used with built-in and
+modular build configurations. For user-space controlled start RapidIO subsystem
+creates the sysfs write-only attribute file '/sys/bus/rapidio/scan'. To initiate
+an enumeration or discovery process on specific mport device, a user needs to
+write mport_ID (not RapidIO destination ID) into that file. The mport_ID is a
+sequential number (0 ... RIO_MAX_MPORTS) assigned during mport device
+registration. For example for machine with single RapidIO controller, mport_ID
+for that controller always will be 0.
+
+To initiate RapidIO enumeration/discovery on all available mports a user may
+write '-1' (or RIO_MPORT_ANY) into the scan attribute file.
+
+4.4 Basic Enumeration Method
+----------------------------
+
+This is an original enumeration/discovery method which is available since
+first release of RapidIO subsystem code. The enumeration process is
+implemented according to the enumeration algorithm outlined in the RapidIO
+Interconnect Specification: Annex I [1].
+
+This method can be configured as statically linked or loadable module.
+The method's single parameter "scan" allows to trigger the enumeration/discovery
+process from module initialization routine.
+
+This enumeration/discovery method can be started only once and does not support
+unloading if it is built as a module.
The enumeration process traverses the network using a recursive depth-first
algorithm. When a new device is found, the enumerator takes ownership of that
an agent skips RapidIO discovery and continues with remaining kernel
initialization.
+4.5 Adding New Enumeration/Discovery Method
+-------------------------------------------
+
+RapidIO subsystem code organization allows addition of new enumeration/discovery
+methods as new configuration options without significant impact to to the core
+RapidIO code.
+
+A new enumeration/discovery method has to be attached to one or more mport
+devices before an enumeration/discovery process can be started. Normally,
+method's module initialization routine calls rio_register_scan() to attach
+an enumerator to a specified mport device (or devices). The basic enumerator
+implementation demonstrates this process.
+
5. References
-------------
IDT_GEN2:
errlog - reads contents of device error log until it is empty.
+
+
+5. RapidIO Bus Attributes
+-------------------------
+
+RapidIO bus subdirectory /sys/bus/rapidio implements the following bus-specific
+attribute:
+
+ scan - allows to trigger enumeration discovery process from user space. This
+ is a write-only attribute. To initiate an enumeration or discovery
+ process on specific mport device, a user needs to write mport_ID (not
+ RapidIO destination ID) into this file. The mport_ID is a sequential
+ number (0 ... RIO_MAX_MPORTS) assigned to the mport device.
+ For example, for a machine with a single RapidIO controller, mport_ID
+ for that controller always will be 0.
+ To initiate RapidIO enumeration/discovery on all available mports
+ a user must write '-1' (or RIO_MPORT_ANY) into this attribute file.
ECRYPT FILE SYSTEM
M: Tyler Hicks <tyhicks@canonical.com>
-M: Dustin Kirkland <dustin.kirkland@gazzang.com>
L: ecryptfs@vger.kernel.org
+W: http://ecryptfs.org
W: https://launchpad.net/ecryptfs
S: Supported
F: Documentation/filesystems/ecryptfs.txt
F: drivers/net/wan/sdla.c
FRAMEBUFFER LAYER
-M: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
+M: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
+M: Tomi Valkeinen <tomi.valkeinen@ti.com>
L: linux-fbdev@vger.kernel.org
W: http://linux-fbdev.sourceforge.net/
Q: http://patchwork.kernel.org/project/linux-fbdev/list/
-T: git git://github.com/schandinat/linux-2.6.git fbdev-next
+T: git git://git.kernel.org/pub/scm/linux/kernel/git/plagnioj/linux-fbdev.git
S: Maintained
F: Documentation/fb/
F: Documentation/devicetree/bindings/fb/
M: Haiyang Zhang <haiyangz@microsoft.com>
L: devel@linuxdriverproject.org
S: Maintained
-F: drivers/hv/
+F: arch/x86/include/asm/mshyperv.h
+F: arch/x86/include/uapi/asm/hyperv.h
+F: arch/x86/kernel/cpu/mshyperv.c
F: drivers/hid/hid-hyperv.c
+F: drivers/hv/
F: drivers/net/hyperv/
+F: drivers/scsi/storvsc_drv.c
+F: drivers/video/hyperv_fb.c
+F: include/linux/hyperv.h
+F: tools/hv/
I2C OVER PARALLEL PORT
M: Jean Delvare <khali@linux-fr.org>
F: drivers/scsi/*iscsi*
F: include/scsi/*iscsi*
+ISCSI EXTENSIONS FOR RDMA (ISER) INITIATOR
+M: Or Gerlitz <ogerlitz@mellanox.com>
+M: Roi Dayan <roid@mellanox.com>
+L: linux-rdma@vger.kernel.org
+S: Supported
+W: http://www.openfabrics.org
+W: www.open-iscsi.org
+Q: http://patchwork.kernel.org/project/linux-rdma/list/
+F: drivers/infiniband/ulp/iser
+
ISDN SUBSYSTEM
M: Karsten Keil <isdn@linux-pingi.de>
L: isdn4linux@listserv.isdn4linux.de (subscribers-only)
F: include/uapi/linux/sunrpc/
KERNEL VIRTUAL MACHINE (KVM)
-M: Marcelo Tosatti <mtosatti@redhat.com>
M: Gleb Natapov <gleb@redhat.com>
+M: Paolo Bonzini <pbonzini@redhat.com>
L: kvm@vger.kernel.org
-W: http://kvm.qumranet.com
+W: http://linux-kvm.org
S: Supported
-F: Documentation/*/kvm.txt
+F: Documentation/*/kvm*.txt
+F: Documentation/virtual/kvm/
F: arch/*/kvm/
F: arch/*/include/asm/kvm*
F: include/linux/kvm*
F: Documentation/networking/vxge.txt
F: drivers/net/ethernet/neterion/
-NETFILTER/IPTABLES/IPCHAINS
-P: Harald Welte
-P: Jozsef Kadlecsik
+NETFILTER/IPTABLES
M: Pablo Neira Ayuso <pablo@netfilter.org>
M: Patrick McHardy <kaber@trash.net>
+M: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
L: netfilter-devel@vger.kernel.org
L: netfilter@vger.kernel.org
L: coreteam@netfilter.org
W: http://www.netfilter.org/
W: http://www.iptables.org/
-T: git git://1984.lsi.us.es/nf
-T: git git://1984.lsi.us.es/nf-next
+Q: http://patchwork.ozlabs.org/project/netfilter-devel/list/
+T: git git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf.git
+T: git git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf-next.git
S: Supported
F: include/linux/netfilter*
F: include/linux/netfilter/
W: http://www.parisc-linux.org/
Q: http://patchwork.kernel.org/project/linux-parisc/list/
T: git git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6.git
+T: git git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux.git
S: Maintained
F: arch/parisc/
+F: Documentation/parisc/
F: drivers/parisc/
+F: drivers/char/agp/parisc-agp.c
+F: drivers/input/serio/gscps2.c
+F: drivers/parport/parport_gsc.*
+F: drivers/tty/serial/8250/8250_gsc.c
+F: drivers/video/sti*
+F: drivers/video/console/sti*
+F: drivers/video/logo/logo_parisc*
PC87360 HARDWARE MONITORING DRIVER
M: Jim Cromie <jim.cromie@gmail.com>
VERSION = 3
PATCHLEVEL = 10
SUBLEVEL = 0
-EXTRAVERSION = -rc2
+EXTRAVERSION = -rc4
NAME = Unicycling Gorilla
# *DOCUMENTATION*
soc100 {
uart@FF100000 {
- pinctrl-names = "abilis,simple-default";
+ pinctrl-names = "default";
pinctrl-0 = <&pctl_uart0>;
};
ethernet@FE100000 {
soc100 {
uart@FF100000 {
- pinctrl-names = "abilis,simple-default";
+ pinctrl-names = "default";
pinctrl-0 = <&pctl_uart0>;
};
ethernet@FE100000 {
};
uart@FF100000 {
- compatible = "snps,dw-apb-uart",
- "abilis,simple-pinctrl";
+ compatible = "snps,dw-apb-uart";
reg = <0xFF100000 0x100>;
clock-frequency = <166666666>;
interrupts = <25 1>;
#address-cells = <1>;
#size-cells = <0>;
cell-index = <1>;
- compatible = "abilis,tb100-spi",
- "abilis,simple-pinctrl";
+ compatible = "abilis,tb100-spi";
num-cs = <2>;
reg = <0xFE011000 0x20>;
interrupt-parent = <&tb10x_ictl>;
#endif
}
-#define CACHE_COLOR(addr) (((unsigned long)(addr) >> (PAGE_SHIFT)) & 3)
+#define CACHE_COLOR(addr) (((unsigned long)(addr) >> (PAGE_SHIFT)) & 1)
/*
* checks if two addresses (after page aligning) index into same cache set
*/
#define addr_not_cache_congruent(addr1, addr2) \
+({ \
cache_is_vipt_aliasing() ? \
- (CACHE_COLOR(addr1) != CACHE_COLOR(addr2)) : 0 \
+ (CACHE_COLOR(addr1) != CACHE_COLOR(addr2)) : 0; \
+})
#define copy_to_user_page(vma, page, vaddr, dst, src, len) \
do { \
#define clear_page(paddr) memset((paddr), 0, PAGE_SIZE)
#define copy_page(to, from) memcpy((to), (from), PAGE_SIZE)
-#ifndef CONFIG_ARC_CACHE_VIPT_ALIASING
-
-#define clear_user_page(addr, vaddr, pg) clear_page(addr)
-#define copy_user_page(vto, vfrom, vaddr, pg) copy_page(vto, vfrom)
-
-#else /* VIPT aliasing dcache */
-
struct vm_area_struct;
struct page;
unsigned long u_vaddr, struct vm_area_struct *vma);
void clear_user_page(void *to, unsigned long u_vaddr, struct page *page);
-#endif /* CONFIG_ARC_CACHE_VIPT_ALIASING */
-
#undef STRICT_MM_TYPECHECKS
#ifdef STRICT_MM_TYPECHECKS
#define _PAGE_ACCESSED (1<<1) /* Page is accessed (S) */
#define _PAGE_CACHEABLE (1<<2) /* Page is cached (H) */
-#define _PAGE_EXECUTE (1<<3) /* Page has user execute perm (H) */
-#define _PAGE_WRITE (1<<4) /* Page has user write perm (H) */
-#define _PAGE_READ (1<<5) /* Page has user read perm (H) */
+#define _PAGE_U_EXECUTE (1<<3) /* Page has user execute perm (H) */
+#define _PAGE_U_WRITE (1<<4) /* Page has user write perm (H) */
+#define _PAGE_U_READ (1<<5) /* Page has user read perm (H) */
#define _PAGE_K_EXECUTE (1<<6) /* Page has kernel execute perm (H) */
#define _PAGE_K_WRITE (1<<7) /* Page has kernel write perm (H) */
#define _PAGE_K_READ (1<<8) /* Page has kernel perm (H) */
/* PD1 */
#define _PAGE_CACHEABLE (1<<0) /* Page is cached (H) */
-#define _PAGE_EXECUTE (1<<1) /* Page has user execute perm (H) */
-#define _PAGE_WRITE (1<<2) /* Page has user write perm (H) */
-#define _PAGE_READ (1<<3) /* Page has user read perm (H) */
+#define _PAGE_U_EXECUTE (1<<1) /* Page has user execute perm (H) */
+#define _PAGE_U_WRITE (1<<2) /* Page has user write perm (H) */
+#define _PAGE_U_READ (1<<3) /* Page has user read perm (H) */
#define _PAGE_K_EXECUTE (1<<4) /* Page has kernel execute perm (H) */
#define _PAGE_K_WRITE (1<<5) /* Page has kernel write perm (H) */
#define _PAGE_K_READ (1<<6) /* Page has kernel perm (H) */
#endif
/* Kernel allowed all permissions for all pages */
-#define _K_PAGE_PERMS (_PAGE_K_EXECUTE | _PAGE_K_WRITE | _PAGE_K_READ)
+#define _K_PAGE_PERMS (_PAGE_K_EXECUTE | _PAGE_K_WRITE | _PAGE_K_READ | \
+ _PAGE_GLOBAL | _PAGE_PRESENT)
#ifdef CONFIG_ARC_CACHE_PAGES
#define _PAGE_DEF_CACHEABLE _PAGE_CACHEABLE
* -by default cached, unless config otherwise
* -present in memory
*/
-#define ___DEF (_PAGE_PRESENT | _K_PAGE_PERMS | _PAGE_DEF_CACHEABLE)
+#define ___DEF (_PAGE_PRESENT | _PAGE_DEF_CACHEABLE)
+
+#define _PAGE_READ (_PAGE_U_READ | _PAGE_K_READ)
+#define _PAGE_WRITE (_PAGE_U_WRITE | _PAGE_K_WRITE)
+#define _PAGE_EXECUTE (_PAGE_U_EXECUTE | _PAGE_K_EXECUTE)
/* Set of bits not changed in pte_modify */
#define _PAGE_CHG_MASK (PAGE_MASK | _PAGE_ACCESSED | _PAGE_MODIFIED)
* kernel vaddr space - visible in all addr spaces, but kernel mode only
* Thus Global, all-kernel-access, no-user-access, cached
*/
-#define PAGE_KERNEL __pgprot(___DEF | _PAGE_GLOBAL)
+#define PAGE_KERNEL __pgprot(_K_PAGE_PERMS | _PAGE_DEF_CACHEABLE)
/* ioremap */
-#define PAGE_KERNEL_NO_CACHE __pgprot(_PAGE_PRESENT | _K_PAGE_PERMS | \
- _PAGE_GLOBAL)
+#define PAGE_KERNEL_NO_CACHE __pgprot(_K_PAGE_PERMS)
/**************************************************************************
* Mapping of vm_flags (Generic VM) to PTE flags (arch specific)
/* Masks for actual TLB "PD"s */
#define PTE_BITS_IN_PD0 (_PAGE_GLOBAL | _PAGE_PRESENT)
#define PTE_BITS_IN_PD1 (PAGE_MASK | _PAGE_CACHEABLE | \
- _PAGE_EXECUTE | _PAGE_WRITE | _PAGE_READ | \
+ _PAGE_U_EXECUTE | _PAGE_U_WRITE | _PAGE_U_READ | \
_PAGE_K_EXECUTE | _PAGE_K_WRITE | _PAGE_K_READ)
#ifndef __ASSEMBLY__
local_irq_save(flags);
__ic_line_inv_vaddr(paddr, vaddr, len);
- __dc_line_op(paddr, vaddr, len, OP_FLUSH);
+ __dc_line_op(paddr, vaddr, len, OP_FLUSH_N_INV);
local_irq_restore(flags);
}
flush_cache_all();
}
+void flush_anon_page(struct vm_area_struct *vma, struct page *page,
+ unsigned long u_vaddr)
+{
+ /* TBD: do we really need to clear the kernel mapping */
+ __flush_dcache_page(page_address(page), u_vaddr);
+ __flush_dcache_page(page_address(page), page_address(page));
+
+}
+
+#endif
+
void copy_user_highpage(struct page *to, struct page *from,
unsigned long u_vaddr, struct vm_area_struct *vma)
{
set_bit(PG_arch_1, &page->flags);
}
-void flush_anon_page(struct vm_area_struct *vma, struct page *page,
- unsigned long u_vaddr)
-{
- /* TBD: do we really need to clear the kernel mapping */
- __flush_dcache_page(page_address(page), u_vaddr);
- __flush_dcache_page(page_address(page), page_address(page));
-
-}
-
-#endif
/**********************************************************************
* Explicit Cache flush request from user space via syscall
* so userspace sees the right data.
* (Avoids the flush for Non-exec + congruent mapping case)
*/
- if (vma->vm_flags & VM_EXEC || addr_not_cache_congruent(paddr, vaddr)) {
+ if ((vma->vm_flags & VM_EXEC) ||
+ addr_not_cache_congruent(paddr, vaddr)) {
struct page *page = pfn_to_page(pte_pfn(*ptep));
int dirty = test_and_clear_bit(PG_arch_1, &page->flags);
;----------------------------------------------------------------
; VERIFY_PTE: Check if PTE permissions approp for executing code
cmp_s r2, VMALLOC_START
- mov.lo r2, (_PAGE_PRESENT | _PAGE_READ | _PAGE_EXECUTE)
+ mov.lo r2, (_PAGE_PRESENT | _PAGE_U_READ | _PAGE_U_EXECUTE)
mov.hs r2, (_PAGE_PRESENT | _PAGE_K_READ | _PAGE_K_EXECUTE)
and r3, r0, r2 ; Mask out NON Flag bits from PTE
mov_s r2, 0
lr r3, [ecr]
btst_s r3, ECR_C_BIT_DTLB_LD_MISS ; Read Access
- or.nz r2, r2, _PAGE_READ ; chk for Read flag in PTE
+ or.nz r2, r2, _PAGE_U_READ ; chk for Read flag in PTE
btst_s r3, ECR_C_BIT_DTLB_ST_MISS ; Write Access
- or.nz r2, r2, _PAGE_WRITE ; chk for Write flag in PTE
+ or.nz r2, r2, _PAGE_U_WRITE ; chk for Write flag in PTE
; Above laddering takes care of XCHG access
; which is both Read and Write
of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
}
-static void __init tb10x_platform_late_init(void)
-{
- struct device_node *dn;
-
- /*
- * Pinctrl documentation recommends setting up the iomux here for
- * all modules which don't require control over the pins themselves.
- * Modules which need this kind of assistance are compatible with
- * "abilis,simple-pinctrl", i.e. we can easily iterate over them.
- * TODO: Does this recommended method work cleanly with pins required
- * by modules?
- */
- for_each_compatible_node(dn, NULL, "abilis,simple-pinctrl") {
- struct platform_device *pd = of_find_device_by_node(dn);
- struct pinctrl *pctl;
-
- pctl = pinctrl_get_select(&pd->dev, "abilis,simple-default");
- if (IS_ERR(pctl)) {
- int ret = PTR_ERR(pctl);
- dev_err(&pd->dev, "Could not set up pinctrl: %d\n",
- ret);
- }
- }
-}
-
static const char *tb10x_compat[] __initdata = {
"abilis,arc-tb10x",
NULL,
MACHINE_START(TB10x, "tb10x")
.dt_compat = tb10x_compat,
.init_machine = tb10x_platform_init,
- .init_late = tb10x_platform_late_init,
MACHINE_END
spear320-evb.dtb \
spear320-hmi.dtb
dtb-$(CONFIG_ARCH_SPEAR6XX)+= spear600-evb.dtb
-dtb-$(CONFIG_ARCH_SUNXI) += sun4i-a10-cubieboard.dtb \
+dtb-$(CONFIG_ARCH_SUNXI) += \
+ sun4i-a10-cubieboard.dtb \
+ sun4i-a10-mini-xplus.dtb \
sun4i-a10-hackberry.dtb \
sun5i-a13-olinuxino.dtb
dtb-$(CONFIG_ARCH_TEGRA) += tegra20-harmony.dtb \
#size-cells = <1>;
compatible = "simple-bus";
interrupt-parent = <&mpic>;
- ranges = <0 0 0xd0000000 0x100000>;
+ ranges = <0 0 0xd0000000 0x0100000 /* internal registers */
+ 0xe0000000 0 0xe0000000 0x8100000 /* PCIe */>;
internal-regs {
compatible = "simple-bus";
};
soc {
- ranges = <0 0xd0000000 0x100000>;
+ ranges = <0 0xd0000000 0x0100000 /* internal registers */
+ 0xe0000000 0xe0000000 0x8100000 /* PCIe */>;
internal-regs {
system-controller@18200 {
compatible = "marvell,armada-370-xp-system-controller";
L2: l2-cache {
compatible = "marvell,aurora-outer-cache";
- reg = <0xd0008000 0x1000>;
+ reg = <0x08000 0x1000>;
cache-id-part = <0x100>;
wt-override;
};
- mpic: interrupt-controller@20000 {
+ interrupt-controller@20000 {
reg = <0x20a00 0x1d0>, <0x21870 0x58>;
};
};
soc {
+ ranges = <0 0 0xd0000000 0x100000
+ 0xf0000000 0 0xf0000000 0x1000000>;
+
internal-regs {
serial@12000 {
clock-frequency = <250000000>;
};
soc {
+ ranges = <0 0 0xd0000000 0x100000
+ 0xf0000000 0 0xf0000000 0x8000000>;
+
internal-regs {
serial@12000 {
clock-frequency = <250000000>;
wt-override;
};
- mpic: interrupt-controller@20000 {
+ interrupt-controller@20000 {
reg = <0x20a00 0x2d0>, <0x21070 0x58>;
};
atmel,pins =
<0 10 0x2 0x0 /* PA10 periph B */
0 11 0x2 0x0 /* PA11 periph B */
- 0 24 0x2 0x0 /* PA24 periph B */
+ 0 22 0x2 0x0 /* PA22 periph B */
0 25 0x2 0x0 /* PA25 periph B */
0 26 0x2 0x0 /* PA26 periph B */
0 27 0x2 0x0 /* PA27 periph B */
compatible = "atmel,at91rm9200-aic";
interrupt-controller;
reg = <0xfffff000 0x200>;
+ atmel,external-irqs = <31>;
};
ramc0: ramc@ffffe800 {
/include/ "at91sam9x5ek.dtsi"
/ {
- model = "Atmel AT91SAM9G25-EK";
+ model = "Atmel AT91SAM9X25-EK";
compatible = "atmel,at91sam9x25ek", "atmel,at91sam9x5ek", "atmel,at91sam9x5", "atmel,at91sam9";
ahb {
clock-names = "usbhost";
};
+ usbphy@12130000 {
+ compatible = "samsung,exynos5250-usb2phy";
+ reg = <0x12130000 0x100>;
+ clocks = <&clock 1>, <&clock 285>;
+ clock-names = "ext_xtal", "usbhost";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ usbphy-sys {
+ reg = <0x10040704 0x8>,
+ <0x10050230 0x4>;
+ };
+ };
+
amba {
#address-cells = <1>;
#size-cells = <1>;
usb_otg_hs: usb_otg_hs@480ab000 {
compatible = "ti,omap3-musb";
reg = <0x480ab000 0x1000>;
- interrupts = <0 92 0x4>, <0 93 0x4>;
+ interrupts = <92>, <93>;
interrupt-names = "mc", "dma";
ti,hwmods = "usb_otg_hs";
multipoint = <1>;
compatible = "atmel,at91sam9x5-spi";
reg = <0xf0004000 0x100>;
interrupts = <24 4 3>;
- cs-gpios = <&pioD 13 0
- &pioD 14 0 /* conflicts with SCK0 and CANRX0 */
- &pioD 15 0 /* conflicts with CTS0 and CANTX0 */
- &pioD 16 0 /* conflicts with RTS0 and PWMFI3 */
- >;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_spi0>;
status = "disabled";
};
macb0: ethernet@f0028000 {
- compatible = "cnds,pc302-gem", "cdns,gem";
+ compatible = "cdns,pc302-gem", "cdns,gem";
reg = <0xf0028000 0x100>;
interrupts = <34 4 3>;
pinctrl-names = "default";
compatible = "atmel,at91sam9x5-spi";
reg = <0xf8008000 0x100>;
interrupts = <25 4 3>;
- cs-gpios = <&pioC 25 0
- &pioC 26 0 /* conflitcs with TWD1 and ISI_D11 */
- &pioC 27 0 /* conflitcs with TWCK1 and ISI_D10 */
- &pioC 28 0 /* conflitcs with PWMFI0 and ISI_D9 */
- >;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_spi1>;
status = "disabled";
ahb {
apb {
+ spi0: spi@f0004000 {
+ cs-gpios = <&pioD 13 0>, <0>, <0>, <0>;
+ };
+
macb0: ethernet@f0028000 {
phy-mode = "rgmii";
};
bootargs = "root=/dev/ram0 console=ttyAMA1,115200n8 earlyprintk";
};
+ /* This is where the interrupt is routed on the S8815 board */
+ external-bus@34000000 {
+ ethernet@300 {
+ interrupt-parent = <&gpio3>;
+ interrupts = <8 0x1>;
+ };
+ };
+
/* Custom board node with GPIO pins to active etc */
usb-s8815 {
/* The S8815 is using this very GPIO pin for the SMSC91x IRQs */
ethernet-gpio {
- gpios = <&gpio3 19 0x1>;
- interrupts = <19 0x1>;
- interrupt-parent = <&gpio3>;
+ gpios = <&gpio3 8 0x1>;
};
/* This will bias the MMC/SD card detect line */
mmcsd-gpio {
bootargs = "earlyprintk console=ttyS0,115200";
};
- soc {
- uart0: uart@01c28000 {
+ soc@01c20000 {
+ uart0: serial@01c28000 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
status = "okay";
-CONFIG_EXPERIMENTAL=y
+CONFIG_SYSVIPC=y
CONFIG_NO_HZ=y
CONFIG_HIGH_RES_TIMERS=y
CONFIG_BLK_DEV_INITRD=y
CONFIG_MODULE_UNLOAD=y
# CONFIG_BLK_DEV_BSG is not set
CONFIG_PARTITION_ADVANCED=y
-CONFIG_EFI_PARTITION=y
CONFIG_ARCH_EXYNOS=y
-CONFIG_S3C_LOWLEVEL_UART_PORT=1
+CONFIG_S3C_LOWLEVEL_UART_PORT=3
CONFIG_S3C24XX_PWM=y
CONFIG_ARCH_EXYNOS5=y
CONFIG_MACH_EXYNOS4_DT=y
-CONFIG_MACH_EXYNOS5_DT=y
CONFIG_SMP=y
CONFIG_NR_CPUS=2
CONFIG_PREEMPT=y
CONFIG_AEABI=y
+CONFIG_HIGHMEM=y
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
CONFIG_ARM_APPENDED_DTB=y
CONFIG_ARM_ATAG_DTB_COMPAT=y
CONFIG_CMDLINE="root=/dev/ram0 rw ramdisk=8192 initrd=0x41000000,8M console=ttySAC1,115200 init=/linuxrc mem=256M"
CONFIG_INET=y
CONFIG_RFKILL_REGULATOR=y
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
CONFIG_PROC_DEVICETREE=y
CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_CRYPTOLOOP=y
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_SIZE=8192
CONFIG_SCSI=y
CONFIG_BLK_DEV_SD=y
CONFIG_CHR_DEV_SG=y
+CONFIG_MD=y
+CONFIG_BLK_DEV_DM=y
+CONFIG_DM_CRYPT=m
CONFIG_NETDEVICES=y
CONFIG_SMSC911X=y
CONFIG_USB_USBNET=y
CONFIG_USB_NET_SMSC75XX=y
CONFIG_USB_NET_SMSC95XX=y
CONFIG_INPUT_EVDEV=y
-# CONFIG_INPUT_KEYBOARD is not set
-# CONFIG_INPUT_MOUSE is not set
+CONFIG_KEYBOARD_CROS_EC=y
+# CONFIG_MOUSE_PS2 is not set
+CONFIG_MOUSE_CYAPA=y
CONFIG_INPUT_TOUCHSCREEN=y
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_SAMSUNG=y
CONFIG_SERIAL_SAMSUNG_CONSOLE=y
CONFIG_SERIAL_OF_PLATFORM=y
CONFIG_HW_RANDOM=y
+CONFIG_TCG_TPM=y
+CONFIG_TCG_TIS_I2C_INFINEON=y
CONFIG_I2C=y
+CONFIG_I2C_MUX=y
+CONFIG_I2C_ARB_GPIO_CHALLENGE=y
+CONFIG_I2C_S3C2410=y
+CONFIG_DEBUG_GPIO=y
# CONFIG_HWMON is not set
+CONFIG_MFD_CROS_EC=y
+CONFIG_MFD_CROS_EC_I2C=y
+CONFIG_MFD_MAX77686=y
+CONFIG_MFD_MAX8997=y
+CONFIG_MFD_SEC_CORE=y
CONFIG_MFD_TPS65090=y
CONFIG_REGULATOR=y
CONFIG_REGULATOR_FIXED_VOLTAGE=y
CONFIG_REGULATOR_GPIO=y
+CONFIG_REGULATOR_MAX8997=y
+CONFIG_REGULATOR_MAX77686=y
+CONFIG_REGULATOR_S5M8767=y
CONFIG_REGULATOR_TPS65090=y
CONFIG_FB=y
+CONFIG_FB_MODE_HELPERS=y
+CONFIG_FB_SIMPLE=y
CONFIG_EXYNOS_VIDEO=y
CONFIG_EXYNOS_MIPI_DSI=y
CONFIG_EXYNOS_DP=y
CONFIG_FONT_7x14=y
CONFIG_LOGO=y
CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_S5P=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_DWC3=y
+CONFIG_USB_PHY=y
+CONFIG_SAMSUNG_USB2PHY=y
+CONFIG_SAMSUNG_USB3PHY=y
+CONFIG_MMC=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_S3C=y
+CONFIG_MMC_DW=y
+CONFIG_MMC_DW_IDMAC=y
+CONFIG_MMC_DW_EXYNOS=y
+CONFIG_COMMON_CLK_MAX77686=y
CONFIG_EXT2_FS=y
CONFIG_EXT3_FS=y
CONFIG_EXT4_FS=y
CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_ASCII=y
CONFIG_NLS_ISO8859_1=y
+CONFIG_PRINTK_TIME=y
CONFIG_MAGIC_SYSRQ=y
CONFIG_DEBUG_KERNEL=y
CONFIG_DETECT_HUNG_TASK=y
CONFIG_DEBUG_MUTEXES=y
CONFIG_DEBUG_INFO=y
CONFIG_DEBUG_USER=y
-CONFIG_DEBUG_LL=y
-CONFIG_EARLY_PRINTK=y
+CONFIG_CRYPTO_SHA256=y
CONFIG_CRC_CCITT=y
CONFIG_USB_DEBUG=y
CONFIG_USB_DEVICEFS=y
# CONFIG_USB_DEVICE_CLASS is not set
-CONFIG_USB_SUSPEND=y
CONFIG_USB_MON=y
CONFIG_USB_OHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_MODVERSIONS=y
CONFIG_MODULE_SRCVERSION_ALL=y
# CONFIG_BLK_DEV_BSG is not set
+CONFIG_ARCH_MULTI_V6=y
CONFIG_ARCH_OMAP2PLUS=y
CONFIG_OMAP_RESET_CLOCKS=y
CONFIG_OMAP_MUX_DEBUG=y
CONFIG_USB_DEBUG=y
CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
CONFIG_USB_DEVICEFS=y
-CONFIG_USB_SUSPEND=y
CONFIG_USB_MON=y
CONFIG_USB_WDM=y
CONFIG_USB_STORAGE=y
CONFIG_MEDIA_USB_SUPPORT=y
CONFIG_USB_VIDEO_CLASS=m
CONFIG_DRM=y
+CONFIG_TEGRA_HOST1X=y
CONFIG_DRM_TEGRA=y
CONFIG_BACKLIGHT_LCD_SUPPORT=y
# CONFIG_LCD_CLASS_DEVICE is not set
CONFIG_STAGING=y
CONFIG_SENSORS_ISL29018=y
CONFIG_SENSORS_ISL29028=y
-CONFIG_SENSORS_AK8975=y
+CONFIG_AK8975=y
CONFIG_MFD_NVEC=y
CONFIG_KEYBOARD_NVEC=y
CONFIG_SERIO_NVEC_PS2=y
add r3,r3,r10 @ E+=F_00_19(B,C,D)
cmp r14,sp
bne .L_00_15 @ [((11+4)*5+2)*3]
+ sub sp,sp,#25*4
#if __ARM_ARCH__<7
ldrb r10,[r1,#2]
ldrb r9,[r1,#3]
add r3,r3,r10 @ E+=F_00_19(B,C,D)
ldr r8,.LK_20_39 @ [+15+16*4]
- sub sp,sp,#25*4
cmn sp,#0 @ [+3], clear carry to denote 20_39
.L_20_39_or_60_79:
ldr r9,[r14,#15*4]
#include <asm/pgalloc.h>
#include <asm/tlbflush.h>
-/*
- * We need to delay page freeing for SMP as other CPUs can access pages
- * which have been removed but not yet had their TLB entries invalidated.
- * Also, as ARMv7 speculative prefetch can drag new entries into the TLB,
- * we need to apply this same delaying tactic to ensure correct operation.
- */
-#if defined(CONFIG_SMP) || defined(CONFIG_CPU_32v7)
-#define tlb_fast_mode(tlb) 0
-#else
-#define tlb_fast_mode(tlb) 1
-#endif
-
#define MMU_GATHER_BUNDLE 8
/*
static inline void tlb_flush_mmu(struct mmu_gather *tlb)
{
tlb_flush(tlb);
- if (!tlb_fast_mode(tlb)) {
- free_pages_and_swap_cache(tlb->pages, tlb->nr);
- tlb->nr = 0;
- if (tlb->pages == tlb->local)
- __tlb_alloc_page(tlb);
- }
+ free_pages_and_swap_cache(tlb->pages, tlb->nr);
+ tlb->nr = 0;
+ if (tlb->pages == tlb->local)
+ __tlb_alloc_page(tlb);
}
static inline void
static inline int __tlb_remove_page(struct mmu_gather *tlb, struct page *page)
{
- if (tlb_fast_mode(tlb)) {
- free_page_and_swap_cache(page);
- return 1; /* avoid calling tlb_flush_mmu */
- }
-
tlb->pages[tlb->nr++] = page;
VM_BUG_ON(tlb->nr > tlb->max);
return tlb->max - tlb->nr;
#define U8500_UART0_PHYS_BASE (0x80120000)
#define U8500_UART1_PHYS_BASE (0x80121000)
#define U8500_UART2_PHYS_BASE (0x80007000)
-#define U8500_UART0_VIRT_BASE (0xa8120000)
-#define U8500_UART1_VIRT_BASE (0xa8121000)
-#define U8500_UART2_VIRT_BASE (0xa8007000)
+#define U8500_UART0_VIRT_BASE (0xf8120000)
+#define U8500_UART1_VIRT_BASE (0xf8121000)
+#define U8500_UART2_VIRT_BASE (0xf8007000)
#define __UX500_PHYS_UART(n) U8500_UART##n##_PHYS_BASE
#define __UX500_VIRT_UART(n) U8500_UART##n##_VIRT_BASE
#endif
.vm_start = 0xffff0000,
.vm_end = 0xffff0000 + PAGE_SIZE,
.vm_flags = VM_READ | VM_EXEC | VM_MAYREAD | VM_MAYEXEC,
- .vm_mm = &init_mm,
};
static int __init gate_vma_init(void)
wait_event_interruptible(*wq, !vcpu->arch.pause);
}
+static int kvm_vcpu_initialized(struct kvm_vcpu *vcpu)
+{
+ return vcpu->arch.target >= 0;
+}
+
/**
* kvm_arch_vcpu_ioctl_run - the main VCPU run function to execute guest code
* @vcpu: The VCPU pointer
int ret;
sigset_t sigsaved;
- /* Make sure they initialize the vcpu with KVM_ARM_VCPU_INIT */
- if (unlikely(vcpu->arch.target < 0))
+ if (unlikely(!kvm_vcpu_initialized(vcpu)))
return -ENOEXEC;
ret = kvm_vcpu_first_run_init(vcpu);
case KVM_SET_ONE_REG:
case KVM_GET_ONE_REG: {
struct kvm_one_reg reg;
+
+ if (unlikely(!kvm_vcpu_initialized(vcpu)))
+ return -ENOEXEC;
+
if (copy_from_user(®, argp, sizeof(reg)))
return -EFAULT;
if (ioctl == KVM_SET_ONE_REG)
struct kvm_reg_list reg_list;
unsigned n;
+ if (unlikely(!kvm_vcpu_initialized(vcpu)))
+ return -ENOEXEC;
+
if (copy_from_user(®_list, user_list, sizeof(reg_list)))
return -EFAULT;
n = reg_list.n;
static void kvm_tlb_flush_vmid_ipa(struct kvm *kvm, phys_addr_t ipa)
{
- kvm_call_hyp(__kvm_tlb_flush_vmid_ipa, kvm, ipa);
+ /*
+ * This function also gets called when dealing with HYP page
+ * tables. As HYP doesn't have an associated struct kvm (and
+ * the HYP page tables are fairly static), we don't do
+ * anything there.
+ */
+ if (kvm)
+ kvm_call_hyp(__kvm_tlb_flush_vmid_ipa, kvm, ipa);
}
static int mmu_topup_memory_cache(struct kvm_mmu_memory_cache *cache,
return p;
}
-static void clear_pud_entry(pud_t *pud)
+static void clear_pud_entry(struct kvm *kvm, pud_t *pud, phys_addr_t addr)
{
pmd_t *pmd_table = pmd_offset(pud, 0);
pud_clear(pud);
+ kvm_tlb_flush_vmid_ipa(kvm, addr);
pmd_free(NULL, pmd_table);
put_page(virt_to_page(pud));
}
-static void clear_pmd_entry(pmd_t *pmd)
+static void clear_pmd_entry(struct kvm *kvm, pmd_t *pmd, phys_addr_t addr)
{
pte_t *pte_table = pte_offset_kernel(pmd, 0);
pmd_clear(pmd);
+ kvm_tlb_flush_vmid_ipa(kvm, addr);
pte_free_kernel(NULL, pte_table);
put_page(virt_to_page(pmd));
}
return page_count(pmd_page) == 1;
}
-static void clear_pte_entry(pte_t *pte)
+static void clear_pte_entry(struct kvm *kvm, pte_t *pte, phys_addr_t addr)
{
if (pte_present(*pte)) {
kvm_set_pte(pte, __pte(0));
put_page(virt_to_page(pte));
+ kvm_tlb_flush_vmid_ipa(kvm, addr);
}
}
return page_count(pte_page) == 1;
}
-static void unmap_range(pgd_t *pgdp, unsigned long long start, u64 size)
+static void unmap_range(struct kvm *kvm, pgd_t *pgdp,
+ unsigned long long start, u64 size)
{
pgd_t *pgd;
pud_t *pud;
}
pte = pte_offset_kernel(pmd, addr);
- clear_pte_entry(pte);
+ clear_pte_entry(kvm, pte, addr);
range = PAGE_SIZE;
/* If we emptied the pte, walk back up the ladder */
if (pte_empty(pte)) {
- clear_pmd_entry(pmd);
+ clear_pmd_entry(kvm, pmd, addr);
range = PMD_SIZE;
if (pmd_empty(pmd)) {
- clear_pud_entry(pud);
+ clear_pud_entry(kvm, pud, addr);
range = PUD_SIZE;
}
}
mutex_lock(&kvm_hyp_pgd_mutex);
if (boot_hyp_pgd) {
- unmap_range(boot_hyp_pgd, hyp_idmap_start, PAGE_SIZE);
- unmap_range(boot_hyp_pgd, TRAMPOLINE_VA, PAGE_SIZE);
+ unmap_range(NULL, boot_hyp_pgd, hyp_idmap_start, PAGE_SIZE);
+ unmap_range(NULL, boot_hyp_pgd, TRAMPOLINE_VA, PAGE_SIZE);
kfree(boot_hyp_pgd);
boot_hyp_pgd = NULL;
}
if (hyp_pgd)
- unmap_range(hyp_pgd, TRAMPOLINE_VA, PAGE_SIZE);
+ unmap_range(NULL, hyp_pgd, TRAMPOLINE_VA, PAGE_SIZE);
kfree(init_bounce_page);
init_bounce_page = NULL;
if (hyp_pgd) {
for (addr = PAGE_OFFSET; virt_addr_valid(addr); addr += PGDIR_SIZE)
- unmap_range(hyp_pgd, KERN_TO_HYP(addr), PGDIR_SIZE);
+ unmap_range(NULL, hyp_pgd, KERN_TO_HYP(addr), PGDIR_SIZE);
for (addr = VMALLOC_START; is_vmalloc_addr((void*)addr); addr += PGDIR_SIZE)
- unmap_range(hyp_pgd, KERN_TO_HYP(addr), PGDIR_SIZE);
+ unmap_range(NULL, hyp_pgd, KERN_TO_HYP(addr), PGDIR_SIZE);
+
kfree(hyp_pgd);
hyp_pgd = NULL;
}
*/
static void unmap_stage2_range(struct kvm *kvm, phys_addr_t start, u64 size)
{
- unmap_range(kvm->arch.pgd, start, size);
+ unmap_range(kvm, kvm->arch.pgd, start, size);
}
/**
static void kvm_unmap_hva_handler(struct kvm *kvm, gpa_t gpa, void *data)
{
unmap_stage2_range(kvm, gpa, PAGE_SIZE);
- kvm_tlb_flush_vmid_ipa(kvm, gpa);
}
int kvm_unmap_hva(struct kvm *kvm, unsigned long hva)
static struct clock_event_device clkevt = {
.name = "at91_tick",
.features = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT,
+ .shift = 32,
.rating = 150,
.set_next_event = clkevt32k_next_event,
.set_mode = clkevt32k_mode,
at91_st_write(AT91_ST_RTMR, 1);
/* Setup timer clockevent, with minimum of two ticks (important!!) */
+ clkevt.mult = div_sc(AT91_SLOW_CLOCK, NSEC_PER_SEC, clkevt.shift);
+ clkevt.max_delta_ns = clockevent_delta2ns(AT91_ST_ALMV, &clkevt);
+ clkevt.min_delta_ns = clockevent_delta2ns(2, &clkevt) + 1;
clkevt.cpumask = cpumask_of(0);
- clockevents_config_and_register(&clkevt, AT91_SLOW_CLOCK,
- 2, AT91_ST_ALMV);
+ clockevents_register_device(&clkevt);
/* register clocksource */
clocksource_register_hz(&clk32k, AT91_SLOW_CLOCK);
at91_init_sram(0, AT91SAM9N12_SRAM_BASE, AT91SAM9N12_SRAM_SIZE);
}
-void __init at91sam9n12_initialize(void)
-{
- at91_extern_irq = (1 << AT91SAM9N12_ID_IRQ0);
-}
-
AT91_SOC_START(at91sam9n12)
.map_io = at91sam9n12_map_io,
.register_clocks = at91sam9n12_register_clocks,
- .init = at91sam9n12_initialize,
AT91_SOC_END
#define AT91_PMC_PCR_CMD (0x1 << 12) /* Command (read=0, write=1) */
#define AT91_PMC_PCR_DIV(n) ((n) << 16) /* Divisor Value */
#define AT91_PMC_PCR_DIV0 0x0 /* Peripheral clock is MCK */
-#define AT91_PMC_PCR_DIV2 0x2 /* Peripheral clock is MCK/2 */
-#define AT91_PMC_PCR_DIV4 0x4 /* Peripheral clock is MCK/4 */
-#define AT91_PMC_PCR_DIV8 0x8 /* Peripheral clock is MCK/8 */
+#define AT91_PMC_PCR_DIV2 0x1 /* Peripheral clock is MCK/2 */
+#define AT91_PMC_PCR_DIV4 0x2 /* Peripheral clock is MCK/4 */
+#define AT91_PMC_PCR_DIV8 0x3 /* Peripheral clock is MCK/8 */
#define AT91_PMC_PCR_EN (0x1 << 28) /* Enable */
#endif
config MACH_UNIVERSAL_C210
bool "Mobile UNIVERSAL_C210 Board"
select CLKSRC_MMIO
+ select CLKSRC_SAMSUNG_PWM
select CPU_EXYNOS4210
select EXYNOS4_SETUP_FIMC
select EXYNOS4_SETUP_FIMD0
select S5P_DEV_TV
select S5P_GPIO_INT
select S5P_SETUP_MIPIPHY
- select SAMSUNG_HRT
help
Machine support for Samsung Mobile Universal S5PC210 Reference
Board.
depends on ARCH_EXYNOS4
select ARM_AMBA
select CLKSRC_OF
+ select CLKSRC_SAMSUNG_PWM if CPU_EXYNOS4210
select CPU_EXYNOS4210
select KEYBOARD_SAMSUNG if INPUT_KEYBOARD
select PINCTRL
*/
#include <linux/kernel.h>
+#include <linux/bitops.h>
#include <linux/interrupt.h>
#include <linux/irq.h>
#include <linux/irqchip.h>
#include <linux/io.h>
#include <linux/device.h>
#include <linux/gpio.h>
+#include <clocksource/samsung_pwm.h>
#include <linux/sched.h>
#include <linux/serial_core.h>
#include <linux/of.h>
},
};
+static struct samsung_pwm_variant exynos4_pwm_variant = {
+ .bits = 32,
+ .div_base = 0,
+ .has_tint_cstat = true,
+ .tclk_mask = 0,
+};
+
void exynos4_restart(char mode, const char *cmd)
{
__raw_writel(0x1, S5P_SWRESET);
val = 0x1;
addr = EXYNOS_SWRESET;
} else if (of_machine_is_compatible("samsung,exynos5440")) {
+ u32 status;
np = of_find_compatible_node(NULL, NULL, "samsung,exynos5440-clock");
+
+ addr = of_iomap(np, 0) + 0xbc;
+ status = __raw_readl(addr);
+
addr = of_iomap(np, 0) + 0xcc;
- val = (0xfff << 20) | (0x1 << 16);
+ val = __raw_readl(addr);
+
+ val = (val & 0xffff0000) | (status & 0xffff);
} else {
pr_err("%s: cannot support non-DT\n", __func__);
return;
iotable_init(exynos5440_iodesc0, ARRAY_SIZE(exynos5440_iodesc0));
}
+void __init exynos_set_timer_source(u8 channels)
+{
+ exynos4_pwm_variant.output_mask = BIT(SAMSUNG_PWM_NUM) - 1;
+ exynos4_pwm_variant.output_mask &= ~channels;
+}
+
void __init exynos_init_time(void)
{
+ unsigned int timer_irqs[SAMSUNG_PWM_NUM] = {
+ EXYNOS4_IRQ_TIMER0_VIC, EXYNOS4_IRQ_TIMER1_VIC,
+ EXYNOS4_IRQ_TIMER2_VIC, EXYNOS4_IRQ_TIMER3_VIC,
+ EXYNOS4_IRQ_TIMER4_VIC,
+ };
+
if (of_have_populated_dt()) {
#ifdef CONFIG_OF
of_clk_init(NULL);
exynos4_clk_init(NULL, !soc_is_exynos4210(), S5P_VA_CMU, readl(S5P_VA_CHIPID + 8) & 1);
exynos4_clk_register_fixed_ext(xxti_f, xusbxti_f);
#endif
- mct_init(S5P_VA_SYSTIMER, EXYNOS4_IRQ_MCT_G0, EXYNOS4_IRQ_MCT_L0, EXYNOS4_IRQ_MCT_L1);
+#ifdef CONFIG_CLKSRC_SAMSUNG_PWM
+ if (soc_is_exynos4210() && samsung_rev() == EXYNOS4210_REV_0)
+ samsung_pwm_clocksource_init(S3C_VA_TIMER,
+ timer_irqs, &exynos4_pwm_variant);
+ else
+#endif
+ mct_init(S5P_VA_SYSTIMER, EXYNOS4_IRQ_MCT_G0,
+ EXYNOS4_IRQ_MCT_L0, EXYNOS4_IRQ_MCT_L1);
}
}
void exynos_firmware_init(void);
+void exynos_set_timer_source(u8 channels);
+
#ifdef CONFIG_PM_GENERIC_DOMAINS
int exynos_pm_late_initcall(void);
#else
#ifndef __ASM_ARCH_PM_CORE_H
#define __ASM_ARCH_PM_CORE_H __FILE__
+#include <linux/of.h>
#include <mach/regs-pmu.h>
+#ifdef CONFIG_PINCTRL_EXYNOS
+extern u32 exynos_get_eint_wake_mask(void);
+#else
+static inline u32 exynos_get_eint_wake_mask(void) { return 0xffffffff; }
+#endif
+
static inline void s3c_pm_debug_init_uart(void)
{
/* nothing here yet */
static inline void s3c_pm_arch_prepare_irqs(void)
{
- __raw_writel(s3c_irqwake_eintmask, S5P_EINT_WAKEUP_MASK);
+ u32 eintmask = s3c_irqwake_eintmask;
+
+ if (of_have_populated_dt())
+ eintmask = exynos_get_eint_wake_mask();
+
+ __raw_writel(eintmask, S5P_EINT_WAKEUP_MASK);
__raw_writel(s3c_irqwake_intmask & ~(1 << 31), S5P_WAKEUP_MASK);
}
#include <plat/mfc.h>
#include <plat/sdhci.h>
#include <plat/fimc-core.h>
-#include <plat/samsung-time.h>
#include <plat/camport.h>
#include <mach/map.h>
{
exynos_init_io(NULL, 0);
s3c24xx_init_uarts(universal_uartcfgs, ARRAY_SIZE(universal_uartcfgs));
- samsung_set_timer_source(SAMSUNG_PWM2, SAMSUNG_PWM4);
+ exynos_set_timer_source(BIT(2) | BIT(4));
xxti_f = 0;
xusbxti_f = 24000000;
}
.map_io = universal_map_io,
.init_machine = universal_machine_init,
.init_late = exynos_init_late,
- .init_time = samsung_timer_init,
+ .init_time = exynos_init_time,
.reserve = &universal_reserve,
.restart = exynos4_restart,
MACHINE_END
static const char *step_sels[] = { "osc", "pll2_pfd2_396m", };
static const char *pll1_sw_sels[] = { "pll1_sys", "step", };
static const char *periph_pre_sels[] = { "pll2_bus", "pll2_pfd2_396m", "pll2_pfd0_352m", "pll2_198m", };
-static const char *periph_clk2_sels[] = { "pll3_usb_otg", "osc", };
+static const char *periph_clk2_sels[] = { "pll3_usb_otg", "osc", "osc", "dummy", };
+static const char *periph2_clk2_sels[] = { "pll3_usb_otg", "pll2_bus", };
static const char *periph_sels[] = { "periph_pre", "periph_clk2", };
static const char *periph2_sels[] = { "periph2_pre", "periph2_clk2", };
static const char *axi_sels[] = { "periph", "pll2_pfd2_396m", "pll3_pfd1_540m", };
static const char *gpu_axi_sels[] = { "axi", "ahb", };
static const char *gpu2d_core_sels[] = { "axi", "pll3_usb_otg", "pll2_pfd0_352m", "pll2_pfd2_396m", };
static const char *gpu3d_core_sels[] = { "mmdc_ch0_axi", "pll3_usb_otg", "pll2_pfd1_594m", "pll2_pfd2_396m", };
-static const char *gpu3d_shader_sels[] = { "mmdc_ch0_axi", "pll3_usb_otg", "pll2_pfd1_594m", "pll2_pfd9_720m", };
+static const char *gpu3d_shader_sels[] = { "mmdc_ch0_axi", "pll3_usb_otg", "pll2_pfd1_594m", "pll3_pfd0_720m", };
static const char *ipu_sels[] = { "mmdc_ch0_axi", "pll2_pfd2_396m", "pll3_120m", "pll3_pfd1_540m", };
static const char *ldb_di_sels[] = { "pll5_video", "pll2_pfd0_352m", "pll2_pfd2_396m", "mmdc_ch1_axi", "pll3_usb_otg", };
static const char *ipu_di_pre_sels[] = { "mmdc_ch0_axi", "pll3_usb_otg", "pll5_video_div", "pll2_pfd0_352m", "pll2_pfd2_396m", "pll3_pfd1_540m", };
clk[pll1_sw] = imx_clk_mux("pll1_sw", base + 0xc, 2, 1, pll1_sw_sels, ARRAY_SIZE(pll1_sw_sels));
clk[periph_pre] = imx_clk_mux("periph_pre", base + 0x18, 18, 2, periph_pre_sels, ARRAY_SIZE(periph_pre_sels));
clk[periph2_pre] = imx_clk_mux("periph2_pre", base + 0x18, 21, 2, periph_pre_sels, ARRAY_SIZE(periph_pre_sels));
- clk[periph_clk2_sel] = imx_clk_mux("periph_clk2_sel", base + 0x18, 12, 1, periph_clk2_sels, ARRAY_SIZE(periph_clk2_sels));
- clk[periph2_clk2_sel] = imx_clk_mux("periph2_clk2_sel", base + 0x18, 20, 1, periph_clk2_sels, ARRAY_SIZE(periph_clk2_sels));
+ clk[periph_clk2_sel] = imx_clk_mux("periph_clk2_sel", base + 0x18, 12, 2, periph_clk2_sels, ARRAY_SIZE(periph_clk2_sels));
+ clk[periph2_clk2_sel] = imx_clk_mux("periph2_clk2_sel", base + 0x18, 20, 1, periph2_clk2_sels, ARRAY_SIZE(periph2_clk2_sels));
clk[axi_sel] = imx_clk_mux("axi_sel", base + 0x14, 6, 2, axi_sels, ARRAY_SIZE(axi_sels));
clk[esai_sel] = imx_clk_mux("esai_sel", base + 0x20, 19, 2, audio_sels, ARRAY_SIZE(audio_sels));
clk[asrc_sel] = imx_clk_mux("asrc_sel", base + 0x30, 7, 2, audio_sels, ARRAY_SIZE(audio_sels));
clk[ldb_di1] = imx_clk_gate2("ldb_di1", "ldb_di1_podf", base + 0x74, 14);
clk[ipu2_di1] = imx_clk_gate2("ipu2_di1", "ipu2_di1_sel", base + 0x74, 10);
clk[hsi_tx] = imx_clk_gate2("hsi_tx", "hsi_tx_podf", base + 0x74, 16);
- clk[mlb] = imx_clk_gate2("mlb", "pll8_mlb", base + 0x74, 18);
+ clk[mlb] = imx_clk_gate2("mlb", "axi", base + 0x74, 18);
clk[mmdc_ch0_axi] = imx_clk_gate2("mmdc_ch0_axi", "mmdc_ch0_axi_podf", base + 0x74, 20);
clk[mmdc_ch1_axi] = imx_clk_gate2("mmdc_ch1_axi", "mmdc_ch1_axi_podf", base + 0x74, 22);
clk[ocram] = imx_clk_gate2("ocram", "ahb", base + 0x74, 28);
.section ".text.head", "ax"
#ifdef CONFIG_SMP
+diag_reg_offset:
+ .word g_diag_reg - .
+
+ .macro set_diag_reg
+ adr r0, diag_reg_offset
+ ldr r1, [r0]
+ add r1, r1, r0 @ r1 = physical &g_diag_reg
+ ldr r0, [r1]
+ mcr p15, 0, r0, c15, c0, 1 @ write diagnostic register
+ .endm
+
ENTRY(v7_secondary_startup)
bl v7_invalidate_l1
+ set_diag_reg
b secondary_startup
ENDPROC(v7_secondary_startup)
#endif
#include <linux/init.h>
#include <linux/smp.h>
+#include <asm/cacheflush.h>
#include <asm/page.h>
#include <asm/smp_scu.h>
#include <asm/mach/map.h>
#define SCU_STANDBY_ENABLE (1 << 5)
+u32 g_diag_reg;
static void __iomem *scu_base;
static struct map_desc scu_io_desc __initdata = {
static void __init imx_smp_prepare_cpus(unsigned int max_cpus)
{
imx_smp_prepare();
+
+ /*
+ * The diagnostic register holds the errata bits. Mostly bootloader
+ * does not bring up secondary cores, so that when errata bits are set
+ * in bootloader, they are set only for boot cpu. But on a SMP
+ * configuration, it should be equally done on every single core.
+ * Read the register from boot cpu here, and will replicate it into
+ * secondary cores when booting them.
+ */
+ asm("mrc p15, 0, %0, c15, c0, 1" : "=r" (g_diag_reg) : : "cc");
+ __cpuc_flush_dcache_area(&g_diag_reg, sizeof(g_diag_reg));
+ outer_clean_range(__pa(&g_diag_reg), __pa(&g_diag_reg + 1));
}
struct smp_operations imx_smp_ops __initdata = {
{
orion_time_set_base(TIMER_VIRT_BASE);
- /*
- * Some Kirkwood devices allocate their coherent buffers from atomic
- * context. Increase size of atomic coherent pool to make sure such
- * the allocations won't fail.
- */
- init_dma_coherent_pool_size(SZ_1M);
mvebu_mbus_init("marvell,kirkwood-mbus",
BRIDGE_WINS_BASE, BRIDGE_WINS_SZ,
DDR_WINDOW_CPU_BASE, DDR_WINDOW_CPU_SZ);
static int __init ts219_pci_init(void)
{
if (machine_is_ts219())
- kirkwood_pcie_init(KW_PCIE0);
+ kirkwood_pcie_init(KW_PCIE1 | KW_PCIE0);
return 0;
}
select MVEBU_CLK_GATING
select MVEBU_MBUS
select ZONE_DMA if ARM_LPAE
+ select ARCH_REQUIRE_GPIOLIB
if ARCH_MVEBU
{
char *mbus_soc_name;
- /*
- * Some Armada 370/XP devices allocate their coherent buffers
- * from atomic context. Increase size of atomic coherent pool
- * to make sure such the allocations won't fail.
- */
- init_dma_coherent_pool_size(SZ_1M);
-
/*
* This initialization will be replaced by a DT-based
* initialization once the mvebu-mbus driver gains DT support.
dev_err(&pdev->dev,
"%s: Memory allocation failed for d->chan!\n",
__func__);
+ ret = -ENOMEM;
goto exit_release_d;
}
*/
DEFINE_CLK_FIXED_FACTOR(clkdiv32k_ck, "clk_24mhz", &clk_24mhz, 0x0, 1, 732);
-DEFINE_CLK_GATE(clkdiv32k_ick, "clkdiv32k_ck", &clkdiv32k_ck, 0x0,
- AM33XX_CM_PER_CLKDIV32K_CLKCTRL, AM33XX_MODULEMODE_SWCTRL_SHIFT,
- 0x0, NULL);
+static struct clk clkdiv32k_ick;
+
+static const char *clkdiv32k_ick_parent_names[] = {
+ "clkdiv32k_ck",
+};
+
+static const struct clk_ops clkdiv32k_ick_ops = {
+ .enable = &omap2_dflt_clk_enable,
+ .disable = &omap2_dflt_clk_disable,
+ .is_enabled = &omap2_dflt_clk_is_enabled,
+ .init = &omap2_init_clk_clkdm,
+};
+
+static struct clk_hw_omap clkdiv32k_ick_hw = {
+ .hw = {
+ .clk = &clkdiv32k_ick,
+ },
+ .enable_reg = AM33XX_CM_PER_CLKDIV32K_CLKCTRL,
+ .enable_bit = AM33XX_MODULEMODE_SWCTRL_SHIFT,
+ .clkdm_name = "clk_24mhz_clkdm",
+};
+
+DEFINE_STRUCT_CLK(clkdiv32k_ick, clkdiv32k_ick_parent_names, clkdiv32k_ick_ops);
/* "usbotg_fck" is an additional clock and not really a modulemode */
DEFINE_CLK_GATE(usbotg_fck, "dpll_per_ck", &dpll_per_ck, 0x0,
clkdm = _get_clkdm(oh);
if (sf & SYSC_HAS_SIDLEMODE) {
+ if (oh->flags & HWMOD_SWSUP_SIDLE ||
+ oh->flags & HWMOD_SWSUP_SIDLE_ACT) {
+ idlemode = HWMOD_IDLEMODE_NO;
+ } else {
+ if (sf & SYSC_HAS_ENAWAKEUP)
+ _enable_wakeup(oh, &v);
+ if (oh->class->sysc->idlemodes & SIDLE_SMART_WKUP)
+ idlemode = HWMOD_IDLEMODE_SMART_WKUP;
+ else
+ idlemode = HWMOD_IDLEMODE_SMART;
+ }
+
+ /*
+ * This is special handling for some IPs like
+ * 32k sync timer. Force them to idle!
+ */
clkdm_act = (clkdm && clkdm->flags & CLKDM_ACTIVE_WITH_MPU);
if (clkdm_act && !(oh->class->sysc->idlemodes &
(SIDLE_SMART | SIDLE_SMART_WKUP)))
idlemode = HWMOD_IDLEMODE_FORCE;
- else
- idlemode = (oh->flags & HWMOD_SWSUP_SIDLE) ?
- HWMOD_IDLEMODE_NO : HWMOD_IDLEMODE_SMART;
+
_set_slave_idlemode(oh, idlemode, &v);
}
(sf & SYSC_HAS_CLOCKACTIVITY))
_set_clockactivity(oh, oh->class->sysc->clockact, &v);
- /* If slave is in SMARTIDLE, also enable wakeup */
- if ((sf & SYSC_HAS_SIDLEMODE) && !(oh->flags & HWMOD_SWSUP_SIDLE))
- _enable_wakeup(oh, &v);
-
_write_sysconfig(v, oh);
/*
sf = oh->class->sysc->sysc_flags;
if (sf & SYSC_HAS_SIDLEMODE) {
- /* XXX What about HWMOD_IDLEMODE_SMART_WKUP? */
- if (oh->flags & HWMOD_SWSUP_SIDLE ||
- !(oh->class->sysc->idlemodes &
- (SIDLE_SMART | SIDLE_SMART_WKUP)))
+ if (oh->flags & HWMOD_SWSUP_SIDLE) {
idlemode = HWMOD_IDLEMODE_FORCE;
- else
- idlemode = HWMOD_IDLEMODE_SMART;
+ } else {
+ if (sf & SYSC_HAS_ENAWAKEUP)
+ _enable_wakeup(oh, &v);
+ if (oh->class->sysc->idlemodes & SIDLE_SMART_WKUP)
+ idlemode = HWMOD_IDLEMODE_SMART_WKUP;
+ else
+ idlemode = HWMOD_IDLEMODE_SMART;
+ }
_set_slave_idlemode(oh, idlemode, &v);
}
_set_master_standbymode(oh, idlemode, &v);
}
- /* If slave is in SMARTIDLE, also enable wakeup */
- if ((sf & SYSC_HAS_SIDLEMODE) && !(oh->flags & HWMOD_SWSUP_SIDLE))
- _enable_wakeup(oh, &v);
-
_write_sysconfig(v, oh);
}
* do so is present in the hwmod data, then call it and pass along the
* return value; otherwise, return 0.
*/
-static int __init _enable_preprogram(struct omap_hwmod *oh)
+static int _enable_preprogram(struct omap_hwmod *oh)
{
if (!oh->class->enable_preprogram)
return 0;
return 0;
}
-/**
- * omap_hwmod_set_ocp_autoidle - set the hwmod's OCP autoidle bit
- * @oh: struct omap_hwmod *
- * @autoidle: desired AUTOIDLE bitfield value (0 or 1)
- *
- * Sets the IP block's OCP autoidle bit in hardware, and updates our
- * local copy. Intended to be used by drivers that require
- * direct manipulation of the AUTOIDLE bits.
- * Returns -EINVAL if @oh is null or is not in the ENABLED state, or passes
- * along the return value from _set_module_autoidle().
- *
- * Any users of this function should be scrutinized carefully.
- */
-int omap_hwmod_set_ocp_autoidle(struct omap_hwmod *oh, u8 autoidle)
-{
- u32 v;
- int retval = 0;
- unsigned long flags;
-
- if (!oh || oh->_state != _HWMOD_STATE_ENABLED)
- return -EINVAL;
-
- spin_lock_irqsave(&oh->_lock, flags);
-
- v = oh->_sysc_cache;
-
- retval = _set_module_autoidle(oh, autoidle, &v);
-
- if (!retval)
- _write_sysconfig(v, oh);
-
- spin_unlock_irqrestore(&oh->_lock, flags);
-
- return retval;
-}
-
/**
* _shutdown - shutdown an omap_hwmod
* @oh: struct omap_hwmod *
return ret;
}
-/**
- * omap_hwmod_set_slave_idlemode - set the hwmod's OCP slave idlemode
- * @oh: struct omap_hwmod *
- * @idlemode: SIDLEMODE field bits (shifted to bit 0)
- *
- * Sets the IP block's OCP slave idlemode in hardware, and updates our
- * local copy. Intended to be used by drivers that have some erratum
- * that requires direct manipulation of the SIDLEMODE bits. Returns
- * -EINVAL if @oh is null, or passes along the return value from
- * _set_slave_idlemode().
- *
- * XXX Does this function have any current users? If not, we should
- * remove it; it is better to let the rest of the hwmod code handle this.
- * Any users of this function should be scrutinized carefully.
- */
-int omap_hwmod_set_slave_idlemode(struct omap_hwmod *oh, u8 idlemode)
-{
- u32 v;
- int retval = 0;
-
- if (!oh)
- return -EINVAL;
-
- v = oh->_sysc_cache;
-
- retval = _set_slave_idlemode(oh, idlemode, &v);
- if (!retval)
- _write_sysconfig(v, oh);
-
- return retval;
-}
-
/**
* omap_hwmod_lookup - look up a registered omap_hwmod by name
* @name: name of the omap_hwmod to look up
* is kept in force-standby mode. Failing to do so causes PM problems
* with musb on OMAP3630 at least. Note that musb has a dedicated register
* to control MSTANDBY signal when MIDLEMODE is set to force-standby.
+ * HWMOD_SWSUP_SIDLE_ACT: omap_hwmod code should manually bring the module
+ * out of idle, but rely on smart-idle to the put it back in idle,
+ * so the wakeups are still functional (Only known case for now is UART)
*/
#define HWMOD_SWSUP_SIDLE (1 << 0)
#define HWMOD_SWSUP_MSTANDBY (1 << 1)
#define HWMOD_EXT_OPT_MAIN_CLK (1 << 9)
#define HWMOD_BLOCK_WFI (1 << 10)
#define HWMOD_FORCE_MSTANDBY (1 << 11)
+#define HWMOD_SWSUP_SIDLE_ACT (1 << 12)
/*
* omap_hwmod._int_flags definitions
int omap_hwmod_enable_clocks(struct omap_hwmod *oh);
int omap_hwmod_disable_clocks(struct omap_hwmod *oh);
-int omap_hwmod_set_slave_idlemode(struct omap_hwmod *oh, u8 idlemode);
-int omap_hwmod_set_ocp_autoidle(struct omap_hwmod *oh, u8 autoidle);
-
int omap_hwmod_reset(struct omap_hwmod *oh);
void omap_hwmod_ocp_barrier(struct omap_hwmod *oh);
.mpu_irqs = omap2_uart1_mpu_irqs,
.sdma_reqs = omap2_uart1_sdma_reqs,
.main_clk = "uart1_fck",
+ .flags = HWMOD_SWSUP_SIDLE_ACT,
.prcm = {
.omap2 = {
.module_offs = CORE_MOD,
.mpu_irqs = omap2_uart2_mpu_irqs,
.sdma_reqs = omap2_uart2_sdma_reqs,
.main_clk = "uart2_fck",
+ .flags = HWMOD_SWSUP_SIDLE_ACT,
.prcm = {
.omap2 = {
.module_offs = CORE_MOD,
.mpu_irqs = omap2_uart3_mpu_irqs,
.sdma_reqs = omap2_uart3_sdma_reqs,
.main_clk = "uart3_fck",
+ .flags = HWMOD_SWSUP_SIDLE_ACT,
.prcm = {
.omap2 = {
.module_offs = CORE_MOD,
.name = "uart1",
.class = &uart_class,
.clkdm_name = "l4_wkup_clkdm",
+ .flags = HWMOD_SWSUP_SIDLE_ACT,
.mpu_irqs = am33xx_uart1_irqs,
.sdma_reqs = uart1_edma_reqs,
.main_clk = "dpll_per_m2_div4_wkupdm_ck",
.name = "uart2",
.class = &uart_class,
.clkdm_name = "l4ls_clkdm",
+ .flags = HWMOD_SWSUP_SIDLE_ACT,
.mpu_irqs = am33xx_uart2_irqs,
.sdma_reqs = uart1_edma_reqs,
.main_clk = "dpll_per_m2_div4_ck",
.name = "uart3",
.class = &uart_class,
.clkdm_name = "l4ls_clkdm",
+ .flags = HWMOD_SWSUP_SIDLE_ACT,
.mpu_irqs = am33xx_uart3_irqs,
.sdma_reqs = uart3_edma_reqs,
.main_clk = "dpll_per_m2_div4_ck",
.name = "uart4",
.class = &uart_class,
.clkdm_name = "l4ls_clkdm",
+ .flags = HWMOD_SWSUP_SIDLE_ACT,
.mpu_irqs = am33xx_uart4_irqs,
.sdma_reqs = uart1_edma_reqs,
.main_clk = "dpll_per_m2_div4_ck",
.name = "uart5",
.class = &uart_class,
.clkdm_name = "l4ls_clkdm",
+ .flags = HWMOD_SWSUP_SIDLE_ACT,
.mpu_irqs = am33xx_uart5_irqs,
.sdma_reqs = uart1_edma_reqs,
.main_clk = "dpll_per_m2_div4_ck",
.name = "uart6",
.class = &uart_class,
.clkdm_name = "l4ls_clkdm",
+ .flags = HWMOD_SWSUP_SIDLE_ACT,
.mpu_irqs = am33xx_uart6_irqs,
.sdma_reqs = uart1_edma_reqs,
.main_clk = "dpll_per_m2_div4_ck",
.mpu_irqs = omap2_uart1_mpu_irqs,
.sdma_reqs = omap2_uart1_sdma_reqs,
.main_clk = "uart1_fck",
+ .flags = HWMOD_SWSUP_SIDLE_ACT,
.prcm = {
.omap2 = {
.module_offs = CORE_MOD,
.mpu_irqs = omap2_uart2_mpu_irqs,
.sdma_reqs = omap2_uart2_sdma_reqs,
.main_clk = "uart2_fck",
+ .flags = HWMOD_SWSUP_SIDLE_ACT,
.prcm = {
.omap2 = {
.module_offs = CORE_MOD,
.mpu_irqs = omap2_uart3_mpu_irqs,
.sdma_reqs = omap2_uart3_sdma_reqs,
.main_clk = "uart3_fck",
+ .flags = HWMOD_SWSUP_SIDLE_ACT,
.prcm = {
.omap2 = {
.module_offs = OMAP3430_PER_MOD,
.mpu_irqs = uart4_mpu_irqs,
.sdma_reqs = uart4_sdma_reqs,
.main_clk = "uart4_fck",
+ .flags = HWMOD_SWSUP_SIDLE_ACT,
.prcm = {
.omap2 = {
.module_offs = OMAP3430_PER_MOD,
.name = "uart1",
.class = &omap44xx_uart_hwmod_class,
.clkdm_name = "l4_per_clkdm",
+ .flags = HWMOD_SWSUP_SIDLE_ACT,
.mpu_irqs = omap44xx_uart1_irqs,
.sdma_reqs = omap44xx_uart1_sdma_reqs,
.main_clk = "func_48m_fclk",
.name = "uart2",
.class = &omap44xx_uart_hwmod_class,
.clkdm_name = "l4_per_clkdm",
+ .flags = HWMOD_SWSUP_SIDLE_ACT,
.mpu_irqs = omap44xx_uart2_irqs,
.sdma_reqs = omap44xx_uart2_sdma_reqs,
.main_clk = "func_48m_fclk",
.name = "uart3",
.class = &omap44xx_uart_hwmod_class,
.clkdm_name = "l4_per_clkdm",
- .flags = HWMOD_INIT_NO_IDLE | HWMOD_INIT_NO_RESET,
+ .flags = HWMOD_INIT_NO_IDLE | HWMOD_INIT_NO_RESET |
+ HWMOD_SWSUP_SIDLE_ACT,
.mpu_irqs = omap44xx_uart3_irqs,
.sdma_reqs = omap44xx_uart3_sdma_reqs,
.main_clk = "func_48m_fclk",
.name = "uart4",
.class = &omap44xx_uart_hwmod_class,
.clkdm_name = "l4_per_clkdm",
+ .flags = HWMOD_SWSUP_SIDLE_ACT,
.mpu_irqs = omap44xx_uart4_irqs,
.sdma_reqs = omap44xx_uart4_sdma_reqs,
.main_clk = "func_48m_fclk",
omap_hwmod_disable_wakeup(od->hwmods[0]);
}
-/*
- * Errata i291: [UART]:Cannot Acknowledge Idle Requests
- * in Smartidle Mode When Configured for DMA Operations.
- * WA: configure uart in force idle mode.
- */
-static void omap_uart_set_noidle(struct device *dev)
-{
- struct platform_device *pdev = to_platform_device(dev);
- struct omap_device *od = to_omap_device(pdev);
-
- omap_hwmod_set_slave_idlemode(od->hwmods[0], HWMOD_IDLEMODE_NO);
-}
-
-static void omap_uart_set_smartidle(struct device *dev)
-{
- struct platform_device *pdev = to_platform_device(dev);
- struct omap_device *od = to_omap_device(pdev);
- u8 idlemode;
-
- if (od->hwmods[0]->class->sysc->idlemodes & SIDLE_SMART_WKUP)
- idlemode = HWMOD_IDLEMODE_SMART_WKUP;
- else
- idlemode = HWMOD_IDLEMODE_SMART;
-
- omap_hwmod_set_slave_idlemode(od->hwmods[0], idlemode);
-}
-
#else
static void omap_uart_enable_wakeup(struct device *dev, bool enable)
{}
-static void omap_uart_set_noidle(struct device *dev) {}
-static void omap_uart_set_smartidle(struct device *dev) {}
#endif /* CONFIG_PM */
#ifdef CONFIG_OMAP_MUX
omap_up.uartclk = OMAP24XX_BASE_BAUD * 16;
omap_up.flags = UPF_BOOT_AUTOCONF;
omap_up.get_context_loss_count = omap_pm_get_dev_context_loss_count;
- omap_up.set_forceidle = omap_uart_set_smartidle;
- omap_up.set_noidle = omap_uart_set_noidle;
omap_up.enable_wakeup = omap_uart_enable_wakeup;
omap_up.dma_rx_buf_size = info->dma_rx_buf_size;
omap_up.dma_rx_timeout = info->dma_rx_timeout;
orion_time_set_base(TIMER_VIRT_BASE);
- /*
- * Some Orion5x devices allocate their coherent buffers from atomic
- * context. Increase size of atomic coherent pool to make sure such
- * the allocations won't fail.
- */
- init_dma_coherent_pool_size(SZ_1M);
-
/* Initialize the MBUS driver */
orion5x_pcie_id(&dev, &rev);
if (dev == MV88F5281_DEV_ID)
static struct usb_phy *phy;
static int usb_power_on(struct platform_device *pdev)
{
- if (!phy)
- return -EIO;
+ if (IS_ERR(phy))
+ return PTR_ERR(phy);
pm_runtime_enable(&pdev->dev);
pm_runtime_get_sync(&pdev->dev);
static void usb_power_off(struct platform_device *pdev)
{
- if (!phy)
+ if (IS_ERR(phy))
return;
usb_phy_shutdown(phy);
config ARCH_SUNXI
bool "Allwinner A1X SOCs" if ARCH_MULTI_V7
+ select ARCH_REQUIRE_GPIOLIB
select CLKSRC_MMIO
select CLKSRC_OF
select COMMON_CLK
bool "U8500 Development platform, MOP500 versions"
select I2C
select I2C_NOMADIK
+ select REGULATOR
select REGULATOR_FIXED_VOLTAGE
select SOC_BUS
select UX500_SOC_DB8500
sdi0_reg_info.gpios[0].gpio = GPIO_SDMMC_1V8_3V_SEL;
mop500_pinmaps_init();
- parent = u8500_init_devices(&ab8500_platdata);
+ parent = u8500_init_devices();
for (i = 0; i < ARRAY_SIZE(mop500_platform_devs); i++)
mop500_platform_devs[i]->dev.parent = parent;
sdi0_reg_info.gpios[0].gpio = SNOWBALL_SDMMC_1V8_3V_GPIO;
snowball_pinmaps_init();
- parent = u8500_init_devices(&ab8500_platdata);
+ parent = u8500_init_devices();
for (i = 0; i < ARRAY_SIZE(snowball_platform_devs); i++)
snowball_platform_devs[i]->dev.parent = parent;
sdi0_reg_info.gpios[0].gpio = HREFV60_SDMMC_1V8_3V_GPIO;
hrefv60_pinmaps_init();
- parent = u8500_init_devices(&ab8500_platdata);
+ parent = u8500_init_devices();
for (i = 0; i < ARRAY_SIZE(mop500_platform_devs); i++)
mop500_platform_devs[i]->dev.parent = parent;
/*
* This function is called from the board init
*/
-struct device * __init u8500_init_devices(struct ab8500_platform_data *ab8500)
+struct device * __init u8500_init_devices(void)
{
struct device *parent;
int i;
for (i = 0; i < ARRAY_SIZE(platform_devs); i++)
platform_devs[i]->dev.parent = parent;
- db8500_prcmu_device.dev.platform_data = ab8500;
-
platform_add_devices(platform_devs, ARRAY_SIZE(platform_devs));
return parent;
OF_DEV_AUXDATA("st,nomadik-i2c", 0x8012a000, "nmk-i2c.4", NULL),
OF_DEV_AUXDATA("stericsson,db8500-prcmu", 0x80157000, "db8500-prcmu",
&db8500_prcmu_pdata),
- OF_DEV_AUXDATA("smsc,lan9115", 0x50000000, "smsc911x", NULL),
+ OF_DEV_AUXDATA("smsc,lan9115", 0x50000000, "smsc911x.0", NULL),
/* Requires device name bindings. */
OF_DEV_AUXDATA("stericsson,nmk-pinctrl", U8500_PRCMU_BASE,
"pinctrl-db8500", NULL),
void __init ux500_map_io(void);
extern void __init u8500_map_io(void);
-extern struct device * __init u8500_init_devices(struct ab8500_platform_data *ab8500);
+extern struct device * __init u8500_init_devices(void);
extern void __init ux500_init_irq(void);
extern void __init ux500_init_late(void);
"wm,wm8505",
"wm,wm8750",
"wm,wm8850",
+ NULL
};
DT_MACHINE_START(WMT_DT, "VIA/Wondermedia SoC (Device Tree Support)")
static struct platform_device orion_ge10_shared = {
.name = MV643XX_ETH_SHARED_NAME,
- .id = 1,
+ .id = 2,
.dev = {
.platform_data = &orion_ge10_shared_data,
},
static struct platform_device orion_ge10 = {
.name = MV643XX_ETH_NAME,
- .id = 1,
- .num_resources = 2,
+ .id = 2,
+ .num_resources = 1,
.resource = orion_ge10_resources,
.dev = {
.coherent_dma_mask = DMA_BIT_MASK(32),
static struct platform_device orion_ge11_shared = {
.name = MV643XX_ETH_SHARED_NAME,
- .id = 1,
+ .id = 3,
.dev = {
.platform_data = &orion_ge11_shared_data,
},
static struct platform_device orion_ge11 = {
.name = MV643XX_ETH_NAME,
- .id = 1,
- .num_resources = 2,
+ .id = 3,
+ .num_resources = 1,
.resource = orion_ge11_resources,
.dev = {
.coherent_dma_mask = DMA_BIT_MASK(32),
#ifndef __PLAT_COMMON_H
#include <linux/mv643xx_eth.h>
+#include <linux/platform_data/usb-ehci-orion.h>
struct dsa_platform_data;
struct mv_sata_platform_data;
#ifdef CONFIG_S5P_DEV_FIMD0
static struct resource s5p_fimd0_resource[] = {
[0] = DEFINE_RES_MEM(S5P_PA_FIMD0, SZ_32K),
- [1] = DEFINE_RES_IRQ(IRQ_FIMD0_VSYNC),
- [2] = DEFINE_RES_IRQ(IRQ_FIMD0_FIFO),
- [3] = DEFINE_RES_IRQ(IRQ_FIMD0_SYSTEM),
+ [1] = DEFINE_RES_IRQ_NAMED(IRQ_FIMD0_VSYNC, "vsync"),
+ [2] = DEFINE_RES_IRQ_NAMED(IRQ_FIMD0_FIFO, "fifo"),
+ [3] = DEFINE_RES_IRQ_NAMED(IRQ_FIMD0_SYSTEM, "lcd_sys"),
};
struct platform_device s5p_device_fimd0 = {
str r11, [r10, #TI_PREEMPT]
#endif
ldr r0, VFP_arch_address
- str r5, [r0] @ known non-zero value
+ str r0, [r0] @ set to non-zero value
mov pc, r9 @ we have handled the fault
ENDPROC(vfp_testing_entry)
EXPORT_SYMBOL(__strncpy_from_user);
EXPORT_SYMBOL(copy_page);
+EXPORT_SYMBOL(clear_page);
EXPORT_SYMBOL(__copy_from_user);
EXPORT_SYMBOL(__copy_to_user);
b.eq el0_fpsimd_exc
cmp x24, #ESR_EL1_EC_UNKNOWN // unknown exception in EL0
b.eq el0_undef
+ cmp x24, #ESR_EL1_EC_CP15_32 // CP15 MRC/MCR trap
+ b.eq el0_undef
+ cmp x24, #ESR_EL1_EC_CP15_64 // CP15 MRRC/MCRR trap
+ b.eq el0_undef
+ cmp x24, #ESR_EL1_EC_CP14_MR // CP14 MRC/MCR trap
+ b.eq el0_undef
+ cmp x24, #ESR_EL1_EC_CP14_LS // CP14 LDC/STC trap
+ b.eq el0_undef
+ cmp x24, #ESR_EL1_EC_CP14_64 // CP14 MRRC/MCRR trap
+ b.eq el0_undef
cmp x24, #ESR_EL1_EC_BREAKPT_EL0 // debug exception in EL0
b.ge el0_dbg
b el0_inv
return;
#endif
- if (show_unhandled_signals) {
+ if (show_unhandled_signals && unhandled_signal(current, SIGILL) &&
+ printk_ratelimit()) {
pr_info("%s[%d]: undefined instruction: pc=%p\n",
current->comm, task_pid_nr(current), pc);
dump_instr(KERN_INFO, regs);
}
#endif
- if (show_unhandled_signals) {
+ if (show_unhandled_signals && printk_ratelimit()) {
pr_info("%s[%d]: syscall %d\n", current->comm,
task_pid_nr(current), (int)regs->syscallno);
dump_instr("", regs);
*/
asmlinkage void bad_mode(struct pt_regs *regs, int reason, unsigned int esr)
{
+ siginfo_t info;
+ void __user *pc = (void __user *)instruction_pointer(regs);
console_verbose();
pr_crit("Bad mode in %s handler detected, code 0x%08x\n",
handler[reason], esr);
+ __show_regs(regs);
+
+ info.si_signo = SIGILL;
+ info.si_errno = 0;
+ info.si_code = ILL_ILLOPC;
+ info.si_addr = pc;
- die("Oops - bad mode", regs, 0);
- local_irq_disable();
- panic("bad mode");
+ arm64_notify_die("Oops - bad mode", regs, &info, 0);
}
void __pte_error(const char *file, int line, unsigned long val)
{
struct siginfo si;
- if (show_unhandled_signals) {
+ if (show_unhandled_signals && unhandled_signal(tsk, sig) &&
+ printk_ratelimit()) {
pr_info("%s[%d]: unhandled %s (%d) at 0x%08lx, esr 0x%03x\n",
tsk->comm, task_pid_nr(tsk), fault_name(esr), sig,
addr, esr);
#include <asm/tlbflush.h>
#include <asm/machvec.h>
-#ifdef CONFIG_SMP
-# define tlb_fast_mode(tlb) ((tlb)->nr == ~0U)
-#else
-# define tlb_fast_mode(tlb) (1)
-#endif
-
/*
* If we can't allocate a page to make a big batch of page pointers
* to work on, then just handle a few from the on-stack structure.
struct mmu_gather {
struct mm_struct *mm;
- unsigned int nr; /* == ~0U => fast mode */
+ unsigned int nr;
unsigned int max;
unsigned char fullmm; /* non-zero means full mm flush */
unsigned char need_flush; /* really unmapped some PTEs? */
static inline void
ia64_tlb_flush_mmu (struct mmu_gather *tlb, unsigned long start, unsigned long end)
{
+ unsigned long i;
unsigned int nr;
if (!tlb->need_flush)
/* lastly, release the freed pages */
nr = tlb->nr;
- if (!tlb_fast_mode(tlb)) {
- unsigned long i;
- tlb->nr = 0;
- tlb->start_addr = ~0UL;
- for (i = 0; i < nr; ++i)
- free_page_and_swap_cache(tlb->pages[i]);
- }
+
+ tlb->nr = 0;
+ tlb->start_addr = ~0UL;
+ for (i = 0; i < nr; ++i)
+ free_page_and_swap_cache(tlb->pages[i]);
}
static inline void __tlb_alloc_page(struct mmu_gather *tlb)
tlb->mm = mm;
tlb->max = ARRAY_SIZE(tlb->local);
tlb->pages = tlb->local;
- /*
- * Use fast mode if only 1 CPU is online.
- *
- * It would be tempting to turn on fast-mode for full_mm_flush as well. But this
- * doesn't work because of speculative accesses and software prefetching: the page
- * table of "mm" may (and usually is) the currently active page table and even
- * though the kernel won't do any user-space accesses during the TLB shoot down, a
- * compiler might use speculation or lfetch.fault on what happens to be a valid
- * user-space address. This in turn could trigger a TLB miss fault (or a VHPT
- * walk) and re-insert a TLB entry we just removed. Slow mode avoids such
- * problems. (We could make fast-mode work by switching the current task to a
- * different "mm" during the shootdown.) --davidm 08/02/2002
- */
- tlb->nr = (num_online_cpus() == 1) ? ~0U : 0;
+ tlb->nr = 0;
tlb->fullmm = full_mm_flush;
tlb->start_addr = ~0UL;
}
{
tlb->need_flush = 1;
- if (tlb_fast_mode(tlb)) {
- free_page_and_swap_cache(page);
- return 1; /* avoid calling tlb_flush_mmu */
- }
-
if (!tlb->nr && tlb->pages == tlb->local)
__tlb_alloc_page(tlb);
-CONFIG_EXPERIMENTAL=y
CONFIG_LOCALVERSION="-amiga"
CONFIG_SYSVIPC=y
CONFIG_POSIX_MQUEUE=y
+CONFIG_FHANDLE=y
CONFIG_BSD_PROCESS_ACCT=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_RELAY=y
+CONFIG_BSD_PROCESS_ACCT_V3=y
+CONFIG_LOG_BUF_SHIFT=16
+# CONFIG_UTS_NS is not set
+# CONFIG_IPC_NS is not set
+# CONFIG_PID_NS is not set
+# CONFIG_NET_NS is not set
CONFIG_BLK_DEV_INITRD=y
-# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_SLAB=y
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
-CONFIG_AMIGA=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_ATARI_PARTITION=y
+CONFIG_MAC_PARTITION=y
+CONFIG_BSD_DISKLABEL=y
+CONFIG_MINIX_SUBPARTITION=y
+CONFIG_SOLARIS_X86_PARTITION=y
+CONFIG_UNIXWARE_DISKLABEL=y
+CONFIG_SUN_PARTITION=y
+# CONFIG_EFI_PARTITION is not set
+CONFIG_SYSV68_PARTITION=y
+CONFIG_IOSCHED_DEADLINE=m
CONFIG_M68020=y
CONFIG_M68030=y
CONFIG_M68040=y
CONFIG_M68060=y
-CONFIG_BINFMT_AOUT=m
-CONFIG_BINFMT_MISC=m
+CONFIG_AMIGA=y
CONFIG_ZORRO=y
CONFIG_AMIGA_PCMCIA=y
-CONFIG_HEARTBEAT=y
-CONFIG_PROC_HARDWARE=y
CONFIG_ZORRO_NAMES=y
+# CONFIG_COMPACTION is not set
+CONFIG_CLEANCACHE=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_BINFMT_AOUT=m
+CONFIG_BINFMT_MISC=m
CONFIG_NET=y
CONFIG_PACKET=y
+CONFIG_PACKET_DIAG=m
CONFIG_UNIX=y
+CONFIG_UNIX_DIAG=m
+CONFIG_XFRM_MIGRATE=y
CONFIG_NET_KEY=y
-CONFIG_NET_KEY_MIGRATE=y
CONFIG_INET=y
CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_IP_PNP_RARP=y
CONFIG_NET_IPIP=m
+CONFIG_NET_IPGRE_DEMUX=m
CONFIG_NET_IPGRE=m
CONFIG_SYN_COOKIES=y
+CONFIG_NET_IPVTI=m
CONFIG_INET_AH=m
CONFIG_INET_ESP=m
CONFIG_INET_IPCOMP=m
CONFIG_INET_XFRM_MODE_TRANSPORT=m
CONFIG_INET_XFRM_MODE_TUNNEL=m
CONFIG_INET_XFRM_MODE_BEET=m
+# CONFIG_INET_LRO is not set
CONFIG_INET_DIAG=m
+CONFIG_INET_UDP_DIAG=m
CONFIG_IPV6_PRIVACY=y
CONFIG_IPV6_ROUTER_PREF=y
-CONFIG_IPV6_ROUTE_INFO=y
CONFIG_INET6_AH=m
CONFIG_INET6_ESP=m
CONFIG_INET6_IPCOMP=m
-CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION=m
-CONFIG_IPV6_TUNNEL=m
+CONFIG_IPV6_GRE=m
CONFIG_NETFILTER=y
-CONFIG_NETFILTER_NETLINK_QUEUE=m
CONFIG_NF_CONNTRACK=m
+CONFIG_NF_CONNTRACK_ZONES=y
+# CONFIG_NF_CONNTRACK_PROCFS is not set
# CONFIG_NF_CT_PROTO_DCCP is not set
CONFIG_NF_CT_PROTO_UDPLITE=m
CONFIG_NF_CONNTRACK_AMANDA=m
CONFIG_NF_CONNTRACK_H323=m
CONFIG_NF_CONNTRACK_IRC=m
CONFIG_NF_CONNTRACK_NETBIOS_NS=m
+CONFIG_NF_CONNTRACK_SNMP=m
CONFIG_NF_CONNTRACK_PPTP=m
CONFIG_NF_CONNTRACK_SANE=m
CONFIG_NF_CONNTRACK_SIP=m
CONFIG_NF_CONNTRACK_TFTP=m
+CONFIG_NETFILTER_XT_SET=m
+CONFIG_NETFILTER_XT_TARGET_CHECKSUM=m
CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
CONFIG_NETFILTER_XT_TARGET_CONNMARK=m
CONFIG_NETFILTER_XT_TARGET_DSCP=m
+CONFIG_NETFILTER_XT_TARGET_HMARK=m
+CONFIG_NETFILTER_XT_TARGET_IDLETIMER=m
+CONFIG_NETFILTER_XT_TARGET_LOG=m
CONFIG_NETFILTER_XT_TARGET_MARK=m
CONFIG_NETFILTER_XT_TARGET_NFLOG=m
CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
+CONFIG_NETFILTER_XT_TARGET_NOTRACK=m
+CONFIG_NETFILTER_XT_TARGET_TEE=m
CONFIG_NETFILTER_XT_TARGET_TRACE=m
CONFIG_NETFILTER_XT_TARGET_TCPMSS=m
CONFIG_NETFILTER_XT_TARGET_TCPOPTSTRIP=m
+CONFIG_NETFILTER_XT_MATCH_ADDRTYPE=m
+CONFIG_NETFILTER_XT_MATCH_BPF=m
CONFIG_NETFILTER_XT_MATCH_CLUSTER=m
CONFIG_NETFILTER_XT_MATCH_COMMENT=m
CONFIG_NETFILTER_XT_MATCH_CONNBYTES=m
+CONFIG_NETFILTER_XT_MATCH_CONNLABEL=m
CONFIG_NETFILTER_XT_MATCH_CONNLIMIT=m
CONFIG_NETFILTER_XT_MATCH_CONNMARK=m
CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
+CONFIG_NETFILTER_XT_MATCH_DEVGROUP=m
CONFIG_NETFILTER_XT_MATCH_DSCP=m
CONFIG_NETFILTER_XT_MATCH_ESP=m
CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m
CONFIG_NETFILTER_XT_MATCH_MAC=m
CONFIG_NETFILTER_XT_MATCH_MARK=m
CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
+CONFIG_NETFILTER_XT_MATCH_NFACCT=m
+CONFIG_NETFILTER_XT_MATCH_OSF=m
CONFIG_NETFILTER_XT_MATCH_OWNER=m
CONFIG_NETFILTER_XT_MATCH_POLICY=m
CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m
CONFIG_NETFILTER_XT_MATCH_TCPMSS=m
CONFIG_NETFILTER_XT_MATCH_TIME=m
CONFIG_NETFILTER_XT_MATCH_U32=m
+CONFIG_IP_SET=m
+CONFIG_IP_SET_BITMAP_IP=m
+CONFIG_IP_SET_BITMAP_IPMAC=m
+CONFIG_IP_SET_BITMAP_PORT=m
+CONFIG_IP_SET_HASH_IP=m
+CONFIG_IP_SET_HASH_IPPORT=m
+CONFIG_IP_SET_HASH_IPPORTIP=m
+CONFIG_IP_SET_HASH_IPPORTNET=m
+CONFIG_IP_SET_HASH_NET=m
+CONFIG_IP_SET_HASH_NETPORT=m
+CONFIG_IP_SET_HASH_NETIFACE=m
+CONFIG_IP_SET_LIST_SET=m
CONFIG_NF_CONNTRACK_IPV4=m
-CONFIG_IP_NF_QUEUE=m
CONFIG_IP_NF_IPTABLES=m
-CONFIG_IP_NF_MATCH_ADDRTYPE=m
CONFIG_IP_NF_MATCH_AH=m
CONFIG_IP_NF_MATCH_ECN=m
+CONFIG_IP_NF_MATCH_RPFILTER=m
CONFIG_IP_NF_MATCH_TTL=m
CONFIG_IP_NF_FILTER=m
CONFIG_IP_NF_TARGET_REJECT=m
-CONFIG_IP_NF_TARGET_LOG=m
CONFIG_IP_NF_TARGET_ULOG=m
-CONFIG_NF_NAT=m
+CONFIG_NF_NAT_IPV4=m
CONFIG_IP_NF_TARGET_MASQUERADE=m
CONFIG_IP_NF_TARGET_NETMAP=m
CONFIG_IP_NF_TARGET_REDIRECT=m
-CONFIG_NF_NAT_SNMP_BASIC=m
CONFIG_IP_NF_MANGLE=m
CONFIG_IP_NF_TARGET_CLUSTERIP=m
CONFIG_IP_NF_TARGET_ECN=m
CONFIG_IP_NF_ARPFILTER=m
CONFIG_IP_NF_ARP_MANGLE=m
CONFIG_NF_CONNTRACK_IPV6=m
-CONFIG_IP6_NF_QUEUE=m
CONFIG_IP6_NF_IPTABLES=m
CONFIG_IP6_NF_MATCH_AH=m
CONFIG_IP6_NF_MATCH_EUI64=m
CONFIG_IP6_NF_MATCH_HL=m
CONFIG_IP6_NF_MATCH_IPV6HEADER=m
CONFIG_IP6_NF_MATCH_MH=m
+CONFIG_IP6_NF_MATCH_RPFILTER=m
CONFIG_IP6_NF_MATCH_RT=m
CONFIG_IP6_NF_TARGET_HL=m
-CONFIG_IP6_NF_TARGET_LOG=m
CONFIG_IP6_NF_FILTER=m
CONFIG_IP6_NF_TARGET_REJECT=m
CONFIG_IP6_NF_MANGLE=m
CONFIG_IP6_NF_RAW=m
+CONFIG_NF_NAT_IPV6=m
+CONFIG_IP6_NF_TARGET_MASQUERADE=m
+CONFIG_IP6_NF_TARGET_NPT=m
CONFIG_IP_DCCP=m
# CONFIG_IP_DCCP_CCID3 is not set
+CONFIG_SCTP_COOKIE_HMAC_SHA1=y
+CONFIG_RDS=m
+CONFIG_RDS_TCP=m
+CONFIG_L2TP=m
CONFIG_ATALK=m
+CONFIG_BATMAN_ADV=m
+CONFIG_BATMAN_ADV_DAT=y
+# CONFIG_WIRELESS is not set
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
# CONFIG_FIRMWARE_IN_KERNEL is not set
+# CONFIG_FW_LOADER_USER_HELPER is not set
CONFIG_CONNECTOR=m
CONFIG_PARPORT=m
CONFIG_PARPORT_AMIGA=m
CONFIG_AMIGA_Z2RAM=y
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_CRYPTOLOOP=m
+CONFIG_BLK_DEV_DRBD=m
CONFIG_BLK_DEV_NBD=m
CONFIG_BLK_DEV_RAM=y
CONFIG_CDROM_PKTCDVD=m
CONFIG_ATA_OVER_ETH=m
CONFIG_IDE=y
+CONFIG_IDE_GD_ATAPI=y
CONFIG_BLK_DEV_IDECD=y
CONFIG_BLK_DEV_GAYLE=y
CONFIG_BLK_DEV_BUDDHA=y
CONFIG_BLK_DEV_SR_VENDOR=y
CONFIG_CHR_DEV_SG=m
CONFIG_SCSI_CONSTANTS=y
-CONFIG_SCSI_SAS_LIBSAS=m
-# CONFIG_SCSI_SAS_LIBSAS_DEBUG is not set
-CONFIG_SCSI_SRP_ATTRS=m
-CONFIG_SCSI_SRP_TGT_ATTRS=y
+CONFIG_SCSI_SAS_ATTRS=m
CONFIG_ISCSI_TCP=m
+CONFIG_ISCSI_BOOT_SYSFS=m
CONFIG_A3000_SCSI=y
CONFIG_A2091_SCSI=y
CONFIG_GVP11_SCSI=y
CONFIG_SCSI_A4000T=y
CONFIG_SCSI_ZORRO7XX=y
CONFIG_MD=y
-CONFIG_BLK_DEV_MD=m
CONFIG_MD_LINEAR=m
CONFIG_MD_RAID0=m
-CONFIG_MD_RAID1=m
-CONFIG_MD_RAID456=m
CONFIG_BLK_DEV_DM=m
CONFIG_DM_CRYPT=m
CONFIG_DM_SNAPSHOT=m
+CONFIG_DM_THIN_PROVISIONING=m
+CONFIG_DM_CACHE=m
CONFIG_DM_MIRROR=m
+CONFIG_DM_RAID=m
CONFIG_DM_ZERO=m
CONFIG_DM_MULTIPATH=m
CONFIG_DM_UEVENT=y
+CONFIG_TARGET_CORE=m
+CONFIG_TCM_IBLOCK=m
+CONFIG_TCM_FILEIO=m
+CONFIG_TCM_PSCSI=m
CONFIG_NETDEVICES=y
CONFIG_DUMMY=m
-CONFIG_MACVLAN=m
CONFIG_EQUALIZER=m
+CONFIG_NET_TEAM=m
+CONFIG_NET_TEAM_MODE_BROADCAST=m
+CONFIG_NET_TEAM_MODE_ROUNDROBIN=m
+CONFIG_NET_TEAM_MODE_ACTIVEBACKUP=m
+CONFIG_NET_TEAM_MODE_LOADBALANCE=m
+CONFIG_VXLAN=m
+CONFIG_NETCONSOLE=m
+CONFIG_NETCONSOLE_DYNAMIC=y
CONFIG_VETH=m
-CONFIG_NET_ETHERNET=y
-CONFIG_ARIADNE=y
+# CONFIG_NET_VENDOR_3COM is not set
CONFIG_A2065=y
+CONFIG_ARIADNE=y
+# CONFIG_NET_CADENCE is not set
+# CONFIG_NET_VENDOR_BROADCOM is not set
+# CONFIG_NET_VENDOR_CIRRUS is not set
+# CONFIG_NET_VENDOR_FUJITSU is not set
+# CONFIG_NET_VENDOR_HP is not set
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
CONFIG_HYDRA=y
-CONFIG_ZORRO8390=y
CONFIG_APNE=y
-# CONFIG_NETDEV_1000 is not set
-# CONFIG_NETDEV_10000 is not set
+CONFIG_ZORRO8390=y
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_SMSC is not set
+# CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_WIZNET is not set
CONFIG_PPP=m
-CONFIG_PPP_FILTER=y
-CONFIG_PPP_ASYNC=m
-CONFIG_PPP_SYNC_TTY=m
-CONFIG_PPP_DEFLATE=m
CONFIG_PPP_BSDCOMP=m
+CONFIG_PPP_DEFLATE=m
+CONFIG_PPP_FILTER=y
CONFIG_PPP_MPPE=m
CONFIG_PPPOE=m
+CONFIG_PPTP=m
+CONFIG_PPPOL2TP=m
+CONFIG_PPP_ASYNC=m
+CONFIG_PPP_SYNC_TTY=m
CONFIG_SLIP=m
CONFIG_SLIP_COMPRESSED=y
CONFIG_SLIP_SMART=y
CONFIG_SLIP_MODE_SLIP6=y
-CONFIG_NETCONSOLE=m
-CONFIG_NETCONSOLE_DYNAMIC=y
-CONFIG_INPUT_FF_MEMLESS=m
+# CONFIG_WLAN is not set
+CONFIG_INPUT_EVDEV=m
CONFIG_KEYBOARD_AMIGA=y
# CONFIG_KEYBOARD_ATKBD is not set
# CONFIG_MOUSE_PS2 is not set
CONFIG_INPUT_M68K_BEEP=m
# CONFIG_SERIO is not set
CONFIG_VT_HW_CONSOLE_BINDING=y
+# CONFIG_LEGACY_PTYS is not set
# CONFIG_DEVKMEM is not set
CONFIG_PRINTER=m
# CONFIG_HW_RANDOM is not set
-CONFIG_GEN_RTC=m
-CONFIG_GEN_RTC_X=y
+CONFIG_NTP_PPS=y
+CONFIG_PPS_CLIENT_LDISC=m
+CONFIG_PPS_CLIENT_PARPORT=m
+CONFIG_PTP_1588_CLOCK=m
# CONFIG_HWMON is not set
CONFIG_FB=y
CONFIG_FB_CIRRUS=y
CONFIG_DMASOUND_PAULA=m
CONFIG_HID=m
CONFIG_HIDRAW=y
+CONFIG_UHID=m
+# CONFIG_HID_GENERIC is not set
# CONFIG_USB_SUPPORT is not set
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_MSM6242=m
+CONFIG_RTC_DRV_RP5C01=m
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_HEARTBEAT=y
+CONFIG_PROC_HARDWARE=y
CONFIG_AMIGA_BUILTIN_SERIAL=y
CONFIG_SERIAL_CONSOLE=y
CONFIG_EXT2_FS=y
CONFIG_EXT3_FS=y
# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
# CONFIG_EXT3_FS_XATTR is not set
+CONFIG_EXT4_FS=y
CONFIG_REISERFS_FS=m
CONFIG_JFS_FS=m
CONFIG_XFS_FS=m
CONFIG_OCFS2_FS=m
-# CONFIG_OCFS2_FS_STATS is not set
# CONFIG_OCFS2_DEBUG_MASKLOG is not set
+CONFIG_FANOTIFY=y
CONFIG_QUOTA_NETLINK_INTERFACE=y
# CONFIG_PRINT_QUOTA_WARNING is not set
-CONFIG_AUTOFS_FS=m
CONFIG_AUTOFS4_FS=m
CONFIG_FUSE_FS=m
+CONFIG_CUSE=m
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
CONFIG_UDF_FS=m
-CONFIG_MSDOS_FS=y
+CONFIG_MSDOS_FS=m
CONFIG_VFAT_FS=m
CONFIG_PROC_KCORE=y
CONFIG_TMPFS=y
CONFIG_AFFS_FS=m
+CONFIG_ECRYPT_FS=m
+CONFIG_ECRYPT_FS_MESSAGING=y
CONFIG_HFS_FS=m
CONFIG_HFSPLUS_FS=m
CONFIG_CRAMFS=m
CONFIG_SQUASHFS=m
-CONFIG_MINIX_FS=y
+CONFIG_SQUASHFS_LZO=y
+CONFIG_MINIX_FS=m
+CONFIG_OMFS_FS=m
CONFIG_HPFS_FS=m
+CONFIG_QNX4FS_FS=m
+CONFIG_QNX6FS_FS=m
CONFIG_SYSV_FS=m
CONFIG_UFS_FS=m
CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
CONFIG_NFS_V4=y
+CONFIG_NFS_SWAP=y
+CONFIG_ROOT_NFS=y
CONFIG_NFSD=m
CONFIG_NFSD_V3=y
-CONFIG_SMB_FS=m
-CONFIG_SMB_NLS_DEFAULT=y
+CONFIG_CIFS=m
+# CONFIG_CIFS_DEBUG is not set
CONFIG_CODA_FS=m
CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_CODEPAGE_737=m
CONFIG_NLS_ISO8859_15=m
CONFIG_NLS_KOI8_R=m
CONFIG_NLS_KOI8_U=m
+CONFIG_NLS_MAC_ROMAN=m
+CONFIG_NLS_MAC_CELTIC=m
+CONFIG_NLS_MAC_CENTEURO=m
+CONFIG_NLS_MAC_CROATIAN=m
+CONFIG_NLS_MAC_CYRILLIC=m
+CONFIG_NLS_MAC_GAELIC=m
+CONFIG_NLS_MAC_GREEK=m
+CONFIG_NLS_MAC_ICELAND=m
+CONFIG_NLS_MAC_INUIT=m
+CONFIG_NLS_MAC_ROMANIAN=m
+CONFIG_NLS_MAC_TURKISH=m
CONFIG_DLM=m
CONFIG_MAGIC_SYSRQ=y
-# CONFIG_RCU_CPU_STALL_DETECTOR is not set
-CONFIG_SYSCTL_SYSCALL_CHECK=y
+CONFIG_ASYNC_RAID6_TEST=m
+CONFIG_ENCRYPTED_KEYS=m
+CONFIG_CRYPTO_MANAGER=y
+CONFIG_CRYPTO_USER=m
CONFIG_CRYPTO_NULL=m
CONFIG_CRYPTO_CRYPTD=m
CONFIG_CRYPTO_TEST=m
CONFIG_CRYPTO_LRW=m
CONFIG_CRYPTO_PCBC=m
CONFIG_CRYPTO_XTS=m
-CONFIG_CRYPTO_HMAC=y
CONFIG_CRYPTO_XCBC=m
-CONFIG_CRYPTO_MD4=m
+CONFIG_CRYPTO_VMAC=m
CONFIG_CRYPTO_MICHAEL_MIC=m
CONFIG_CRYPTO_RMD128=m
CONFIG_CRYPTO_RMD160=m
CONFIG_CRYPTO_RMD256=m
CONFIG_CRYPTO_RMD320=m
-CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
CONFIG_CRYPTO_TGR192=m
CONFIG_CRYPTO_WP512=m
-CONFIG_CRYPTO_AES=m
CONFIG_CRYPTO_ANUBIS=m
CONFIG_CRYPTO_BLOWFISH=m
CONFIG_CRYPTO_CAMELLIA=m
CONFIG_CRYPTO_ZLIB=m
CONFIG_CRYPTO_LZO=m
# CONFIG_CRYPTO_ANSI_CPRNG is not set
+CONFIG_CRYPTO_USER_API_HASH=m
+CONFIG_CRYPTO_USER_API_SKCIPHER=m
# CONFIG_CRYPTO_HW is not set
-CONFIG_CRC16=m
CONFIG_CRC_T10DIF=y
+CONFIG_XZ_DEC_X86=y
+CONFIG_XZ_DEC_POWERPC=y
+CONFIG_XZ_DEC_IA64=y
+CONFIG_XZ_DEC_ARM=y
+CONFIG_XZ_DEC_ARMTHUMB=y
+CONFIG_XZ_DEC_SPARC=y
+CONFIG_XZ_DEC_TEST=m
-CONFIG_EXPERIMENTAL=y
CONFIG_LOCALVERSION="-apollo"
CONFIG_SYSVIPC=y
CONFIG_POSIX_MQUEUE=y
+CONFIG_FHANDLE=y
CONFIG_BSD_PROCESS_ACCT=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_RELAY=y
+CONFIG_BSD_PROCESS_ACCT_V3=y
+CONFIG_LOG_BUF_SHIFT=16
+# CONFIG_UTS_NS is not set
+# CONFIG_IPC_NS is not set
+# CONFIG_PID_NS is not set
+# CONFIG_NET_NS is not set
CONFIG_BLK_DEV_INITRD=y
-# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_SLAB=y
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
-CONFIG_APOLLO=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_AMIGA_PARTITION=y
+CONFIG_ATARI_PARTITION=y
+CONFIG_MAC_PARTITION=y
+CONFIG_BSD_DISKLABEL=y
+CONFIG_MINIX_SUBPARTITION=y
+CONFIG_SOLARIS_X86_PARTITION=y
+CONFIG_UNIXWARE_DISKLABEL=y
+CONFIG_SUN_PARTITION=y
+# CONFIG_EFI_PARTITION is not set
+CONFIG_SYSV68_PARTITION=y
+CONFIG_IOSCHED_DEADLINE=m
CONFIG_M68020=y
CONFIG_M68030=y
CONFIG_M68040=y
CONFIG_M68060=y
+CONFIG_APOLLO=y
+# CONFIG_COMPACTION is not set
+CONFIG_CLEANCACHE=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
CONFIG_BINFMT_AOUT=m
CONFIG_BINFMT_MISC=m
-CONFIG_HEARTBEAT=y
-CONFIG_PROC_HARDWARE=y
CONFIG_NET=y
CONFIG_PACKET=y
+CONFIG_PACKET_DIAG=m
CONFIG_UNIX=y
+CONFIG_UNIX_DIAG=m
+CONFIG_XFRM_MIGRATE=y
CONFIG_NET_KEY=y
-CONFIG_NET_KEY_MIGRATE=y
CONFIG_INET=y
CONFIG_IP_PNP=y
CONFIG_IP_PNP_DHCP=y
CONFIG_IP_PNP_BOOTP=y
CONFIG_IP_PNP_RARP=y
CONFIG_NET_IPIP=m
+CONFIG_NET_IPGRE_DEMUX=m
CONFIG_NET_IPGRE=m
CONFIG_SYN_COOKIES=y
+CONFIG_NET_IPVTI=m
CONFIG_INET_AH=m
CONFIG_INET_ESP=m
CONFIG_INET_IPCOMP=m
CONFIG_INET_XFRM_MODE_TRANSPORT=m
CONFIG_INET_XFRM_MODE_TUNNEL=m
CONFIG_INET_XFRM_MODE_BEET=m
+# CONFIG_INET_LRO is not set
CONFIG_INET_DIAG=m
+CONFIG_INET_UDP_DIAG=m
CONFIG_IPV6_PRIVACY=y
CONFIG_IPV6_ROUTER_PREF=y
-CONFIG_IPV6_ROUTE_INFO=y
CONFIG_INET6_AH=m
CONFIG_INET6_ESP=m
CONFIG_INET6_IPCOMP=m
-CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION=m
-CONFIG_IPV6_TUNNEL=m
+CONFIG_IPV6_GRE=m
CONFIG_NETFILTER=y
-CONFIG_NETFILTER_NETLINK_QUEUE=m
CONFIG_NF_CONNTRACK=m
+CONFIG_NF_CONNTRACK_ZONES=y
+# CONFIG_NF_CONNTRACK_PROCFS is not set
# CONFIG_NF_CT_PROTO_DCCP is not set
CONFIG_NF_CT_PROTO_UDPLITE=m
CONFIG_NF_CONNTRACK_AMANDA=m
CONFIG_NF_CONNTRACK_H323=m
CONFIG_NF_CONNTRACK_IRC=m
CONFIG_NF_CONNTRACK_NETBIOS_NS=m
+CONFIG_NF_CONNTRACK_SNMP=m
CONFIG_NF_CONNTRACK_PPTP=m
CONFIG_NF_CONNTRACK_SANE=m
CONFIG_NF_CONNTRACK_SIP=m
CONFIG_NF_CONNTRACK_TFTP=m
+CONFIG_NETFILTER_XT_SET=m
+CONFIG_NETFILTER_XT_TARGET_CHECKSUM=m
CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
CONFIG_NETFILTER_XT_TARGET_CONNMARK=m
CONFIG_NETFILTER_XT_TARGET_DSCP=m
+CONFIG_NETFILTER_XT_TARGET_HMARK=m
+CONFIG_NETFILTER_XT_TARGET_IDLETIMER=m
+CONFIG_NETFILTER_XT_TARGET_LOG=m
CONFIG_NETFILTER_XT_TARGET_MARK=m
CONFIG_NETFILTER_XT_TARGET_NFLOG=m
CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
+CONFIG_NETFILTER_XT_TARGET_NOTRACK=m
+CONFIG_NETFILTER_XT_TARGET_TEE=m
CONFIG_NETFILTER_XT_TARGET_TRACE=m
CONFIG_NETFILTER_XT_TARGET_TCPMSS=m
CONFIG_NETFILTER_XT_TARGET_TCPOPTSTRIP=m
+CONFIG_NETFILTER_XT_MATCH_ADDRTYPE=m
+CONFIG_NETFILTER_XT_MATCH_BPF=m
CONFIG_NETFILTER_XT_MATCH_CLUSTER=m
CONFIG_NETFILTER_XT_MATCH_COMMENT=m
CONFIG_NETFILTER_XT_MATCH_CONNBYTES=m
+CONFIG_NETFILTER_XT_MATCH_CONNLABEL=m
CONFIG_NETFILTER_XT_MATCH_CONNLIMIT=m
CONFIG_NETFILTER_XT_MATCH_CONNMARK=m
CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
+CONFIG_NETFILTER_XT_MATCH_DEVGROUP=m
CONFIG_NETFILTER_XT_MATCH_DSCP=m
CONFIG_NETFILTER_XT_MATCH_ESP=m
CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m
CONFIG_NETFILTER_XT_MATCH_MAC=m
CONFIG_NETFILTER_XT_MATCH_MARK=m
CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
+CONFIG_NETFILTER_XT_MATCH_NFACCT=m
+CONFIG_NETFILTER_XT_MATCH_OSF=m
CONFIG_NETFILTER_XT_MATCH_OWNER=m
CONFIG_NETFILTER_XT_MATCH_POLICY=m
CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m
CONFIG_NETFILTER_XT_MATCH_TCPMSS=m
CONFIG_NETFILTER_XT_MATCH_TIME=m
CONFIG_NETFILTER_XT_MATCH_U32=m
+CONFIG_IP_SET=m
+CONFIG_IP_SET_BITMAP_IP=m
+CONFIG_IP_SET_BITMAP_IPMAC=m
+CONFIG_IP_SET_BITMAP_PORT=m
+CONFIG_IP_SET_HASH_IP=m
+CONFIG_IP_SET_HASH_IPPORT=m
+CONFIG_IP_SET_HASH_IPPORTIP=m
+CONFIG_IP_SET_HASH_IPPORTNET=m
+CONFIG_IP_SET_HASH_NET=m
+CONFIG_IP_SET_HASH_NETPORT=m
+CONFIG_IP_SET_HASH_NETIFACE=m
+CONFIG_IP_SET_LIST_SET=m
CONFIG_NF_CONNTRACK_IPV4=m
-CONFIG_IP_NF_QUEUE=m
CONFIG_IP_NF_IPTABLES=m
-CONFIG_IP_NF_MATCH_ADDRTYPE=m
CONFIG_IP_NF_MATCH_AH=m
CONFIG_IP_NF_MATCH_ECN=m
+CONFIG_IP_NF_MATCH_RPFILTER=m
CONFIG_IP_NF_MATCH_TTL=m
CONFIG_IP_NF_FILTER=m
CONFIG_IP_NF_TARGET_REJECT=m
-CONFIG_IP_NF_TARGET_LOG=m
CONFIG_IP_NF_TARGET_ULOG=m
-CONFIG_NF_NAT=m
+CONFIG_NF_NAT_IPV4=m
CONFIG_IP_NF_TARGET_MASQUERADE=m
CONFIG_IP_NF_TARGET_NETMAP=m
CONFIG_IP_NF_TARGET_REDIRECT=m
-CONFIG_NF_NAT_SNMP_BASIC=m
CONFIG_IP_NF_MANGLE=m
CONFIG_IP_NF_TARGET_CLUSTERIP=m
CONFIG_IP_NF_TARGET_ECN=m
CONFIG_IP_NF_ARPFILTER=m
CONFIG_IP_NF_ARP_MANGLE=m
CONFIG_NF_CONNTRACK_IPV6=m
-CONFIG_IP6_NF_QUEUE=m
CONFIG_IP6_NF_IPTABLES=m
CONFIG_IP6_NF_MATCH_AH=m
CONFIG_IP6_NF_MATCH_EUI64=m
CONFIG_IP6_NF_MATCH_HL=m
CONFIG_IP6_NF_MATCH_IPV6HEADER=m
CONFIG_IP6_NF_MATCH_MH=m
+CONFIG_IP6_NF_MATCH_RPFILTER=m
CONFIG_IP6_NF_MATCH_RT=m
CONFIG_IP6_NF_TARGET_HL=m
-CONFIG_IP6_NF_TARGET_LOG=m
CONFIG_IP6_NF_FILTER=m
CONFIG_IP6_NF_TARGET_REJECT=m
CONFIG_IP6_NF_MANGLE=m
CONFIG_IP6_NF_RAW=m
+CONFIG_NF_NAT_IPV6=m
+CONFIG_IP6_NF_TARGET_MASQUERADE=m
+CONFIG_IP6_NF_TARGET_NPT=m
CONFIG_IP_DCCP=m
# CONFIG_IP_DCCP_CCID3 is not set
+CONFIG_SCTP_COOKIE_HMAC_SHA1=y
+CONFIG_RDS=m
+CONFIG_RDS_TCP=m
+CONFIG_L2TP=m
CONFIG_ATALK=m
+CONFIG_BATMAN_ADV=m
+CONFIG_BATMAN_ADV_DAT=y
+# CONFIG_WIRELESS is not set
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
# CONFIG_FIRMWARE_IN_KERNEL is not set
+# CONFIG_FW_LOADER_USER_HELPER is not set
CONFIG_CONNECTOR=m
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_CRYPTOLOOP=m
+CONFIG_BLK_DEV_DRBD=m
CONFIG_BLK_DEV_NBD=m
CONFIG_BLK_DEV_RAM=y
CONFIG_CDROM_PKTCDVD=m
CONFIG_BLK_DEV_SR_VENDOR=y
CONFIG_CHR_DEV_SG=m
CONFIG_SCSI_CONSTANTS=y
-CONFIG_SCSI_SAS_LIBSAS=m
-# CONFIG_SCSI_SAS_LIBSAS_DEBUG is not set
-CONFIG_SCSI_SRP_ATTRS=m
-CONFIG_SCSI_SRP_TGT_ATTRS=y
+CONFIG_SCSI_SAS_ATTRS=m
CONFIG_ISCSI_TCP=m
+CONFIG_ISCSI_BOOT_SYSFS=m
CONFIG_MD=y
-CONFIG_BLK_DEV_MD=m
CONFIG_MD_LINEAR=m
CONFIG_MD_RAID0=m
-CONFIG_MD_RAID1=m
-CONFIG_MD_RAID456=m
CONFIG_BLK_DEV_DM=m
CONFIG_DM_CRYPT=m
CONFIG_DM_SNAPSHOT=m
+CONFIG_DM_THIN_PROVISIONING=m
+CONFIG_DM_CACHE=m
CONFIG_DM_MIRROR=m
+CONFIG_DM_RAID=m
CONFIG_DM_ZERO=m
CONFIG_DM_MULTIPATH=m
CONFIG_DM_UEVENT=y
+CONFIG_TARGET_CORE=m
+CONFIG_TCM_IBLOCK=m
+CONFIG_TCM_FILEIO=m
+CONFIG_TCM_PSCSI=m
CONFIG_NETDEVICES=y
CONFIG_DUMMY=m
-CONFIG_MACVLAN=m
CONFIG_EQUALIZER=m
+CONFIG_NET_TEAM=m
+CONFIG_NET_TEAM_MODE_BROADCAST=m
+CONFIG_NET_TEAM_MODE_ROUNDROBIN=m
+CONFIG_NET_TEAM_MODE_ACTIVEBACKUP=m
+CONFIG_NET_TEAM_MODE_LOADBALANCE=m
+CONFIG_VXLAN=m
+CONFIG_NETCONSOLE=m
+CONFIG_NETCONSOLE_DYNAMIC=y
CONFIG_VETH=m
-CONFIG_NET_ETHERNET=y
-# CONFIG_NETDEV_1000 is not set
-# CONFIG_NETDEV_10000 is not set
+# CONFIG_NET_CADENCE is not set
+# CONFIG_NET_VENDOR_BROADCOM is not set
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_WIZNET is not set
CONFIG_PPP=m
-CONFIG_PPP_FILTER=y
-CONFIG_PPP_ASYNC=m
-CONFIG_PPP_SYNC_TTY=m
-CONFIG_PPP_DEFLATE=m
CONFIG_PPP_BSDCOMP=m
+CONFIG_PPP_DEFLATE=m
+CONFIG_PPP_FILTER=y
CONFIG_PPP_MPPE=m
CONFIG_PPPOE=m
+CONFIG_PPTP=m
+CONFIG_PPPOL2TP=m
+CONFIG_PPP_ASYNC=m
+CONFIG_PPP_SYNC_TTY=m
CONFIG_SLIP=m
CONFIG_SLIP_COMPRESSED=y
CONFIG_SLIP_SMART=y
CONFIG_SLIP_MODE_SLIP6=y
-CONFIG_NETCONSOLE=m
-CONFIG_NETCONSOLE_DYNAMIC=y
-CONFIG_INPUT_FF_MEMLESS=m
+# CONFIG_WLAN is not set
+CONFIG_INPUT_EVDEV=m
# CONFIG_KEYBOARD_ATKBD is not set
-CONFIG_MOUSE_PS2=m
+# CONFIG_MOUSE_PS2 is not set
CONFIG_MOUSE_SERIAL=m
CONFIG_SERIO=m
-# CONFIG_SERIO_SERPORT is not set
CONFIG_VT_HW_CONSOLE_BINDING=y
+# CONFIG_LEGACY_PTYS is not set
# CONFIG_DEVKMEM is not set
# CONFIG_HW_RANDOM is not set
-CONFIG_GEN_RTC=m
-CONFIG_GEN_RTC_X=y
+CONFIG_NTP_PPS=y
+CONFIG_PPS_CLIENT_LDISC=m
+CONFIG_PTP_1588_CLOCK=m
# CONFIG_HWMON is not set
CONFIG_FB=y
CONFIG_FRAMEBUFFER_CONSOLE=y
# CONFIG_LOGO_LINUX_CLUT224 is not set
CONFIG_HID=m
CONFIG_HIDRAW=y
+CONFIG_UHID=m
+# CONFIG_HID_GENERIC is not set
# CONFIG_USB_SUPPORT is not set
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_GENERIC=m
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_HEARTBEAT=y
+CONFIG_PROC_HARDWARE=y
CONFIG_EXT2_FS=y
CONFIG_EXT3_FS=y
# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
# CONFIG_EXT3_FS_XATTR is not set
+CONFIG_EXT4_FS=y
CONFIG_REISERFS_FS=m
CONFIG_JFS_FS=m
CONFIG_XFS_FS=m
CONFIG_OCFS2_FS=m
-# CONFIG_OCFS2_FS_STATS is not set
# CONFIG_OCFS2_DEBUG_MASKLOG is not set
+CONFIG_FANOTIFY=y
CONFIG_QUOTA_NETLINK_INTERFACE=y
# CONFIG_PRINT_QUOTA_WARNING is not set
-CONFIG_AUTOFS_FS=m
CONFIG_AUTOFS4_FS=m
CONFIG_FUSE_FS=m
+CONFIG_CUSE=m
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
CONFIG_UDF_FS=m
-CONFIG_MSDOS_FS=y
+CONFIG_MSDOS_FS=m
CONFIG_VFAT_FS=m
CONFIG_PROC_KCORE=y
CONFIG_TMPFS=y
CONFIG_AFFS_FS=m
+CONFIG_ECRYPT_FS=m
+CONFIG_ECRYPT_FS_MESSAGING=y
CONFIG_HFS_FS=m
CONFIG_HFSPLUS_FS=m
CONFIG_CRAMFS=m
CONFIG_SQUASHFS=m
-CONFIG_MINIX_FS=y
+CONFIG_SQUASHFS_LZO=y
+CONFIG_MINIX_FS=m
+CONFIG_OMFS_FS=m
CONFIG_HPFS_FS=m
+CONFIG_QNX4FS_FS=m
+CONFIG_QNX6FS_FS=m
CONFIG_SYSV_FS=m
CONFIG_UFS_FS=m
CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
CONFIG_NFS_V4=y
+CONFIG_NFS_SWAP=y
CONFIG_ROOT_NFS=y
CONFIG_NFSD=m
CONFIG_NFSD_V3=y
-CONFIG_SMB_FS=m
-CONFIG_SMB_NLS_DEFAULT=y
+CONFIG_CIFS=m
+# CONFIG_CIFS_DEBUG is not set
CONFIG_CODA_FS=m
CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_CODEPAGE_737=m
CONFIG_NLS_ISO8859_15=m
CONFIG_NLS_KOI8_R=m
CONFIG_NLS_KOI8_U=m
+CONFIG_NLS_MAC_ROMAN=m
+CONFIG_NLS_MAC_CELTIC=m
+CONFIG_NLS_MAC_CENTEURO=m
+CONFIG_NLS_MAC_CROATIAN=m
+CONFIG_NLS_MAC_CYRILLIC=m
+CONFIG_NLS_MAC_GAELIC=m
+CONFIG_NLS_MAC_GREEK=m
+CONFIG_NLS_MAC_ICELAND=m
+CONFIG_NLS_MAC_INUIT=m
+CONFIG_NLS_MAC_ROMANIAN=m
+CONFIG_NLS_MAC_TURKISH=m
CONFIG_DLM=m
CONFIG_MAGIC_SYSRQ=y
-# CONFIG_RCU_CPU_STALL_DETECTOR is not set
-CONFIG_SYSCTL_SYSCALL_CHECK=y
+CONFIG_ASYNC_RAID6_TEST=m
+CONFIG_ENCRYPTED_KEYS=m
+CONFIG_CRYPTO_MANAGER=y
+CONFIG_CRYPTO_USER=m
CONFIG_CRYPTO_NULL=m
CONFIG_CRYPTO_CRYPTD=m
CONFIG_CRYPTO_TEST=m
CONFIG_CRYPTO_LRW=m
CONFIG_CRYPTO_PCBC=m
CONFIG_CRYPTO_XTS=m
-CONFIG_CRYPTO_HMAC=y
CONFIG_CRYPTO_XCBC=m
-CONFIG_CRYPTO_MD4=m
+CONFIG_CRYPTO_VMAC=m
CONFIG_CRYPTO_MICHAEL_MIC=m
CONFIG_CRYPTO_RMD128=m
CONFIG_CRYPTO_RMD160=m
CONFIG_CRYPTO_RMD256=m
CONFIG_CRYPTO_RMD320=m
-CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
CONFIG_CRYPTO_TGR192=m
CONFIG_CRYPTO_WP512=m
-CONFIG_CRYPTO_AES=m
CONFIG_CRYPTO_ANUBIS=m
CONFIG_CRYPTO_BLOWFISH=m
CONFIG_CRYPTO_CAMELLIA=m
CONFIG_CRYPTO_ZLIB=m
CONFIG_CRYPTO_LZO=m
# CONFIG_CRYPTO_ANSI_CPRNG is not set
+CONFIG_CRYPTO_USER_API_HASH=m
+CONFIG_CRYPTO_USER_API_SKCIPHER=m
# CONFIG_CRYPTO_HW is not set
-CONFIG_CRC16=m
CONFIG_CRC_T10DIF=y
+CONFIG_XZ_DEC_X86=y
+CONFIG_XZ_DEC_POWERPC=y
+CONFIG_XZ_DEC_IA64=y
+CONFIG_XZ_DEC_ARM=y
+CONFIG_XZ_DEC_ARMTHUMB=y
+CONFIG_XZ_DEC_SPARC=y
+CONFIG_XZ_DEC_TEST=m
-CONFIG_EXPERIMENTAL=y
CONFIG_LOCALVERSION="-atari"
CONFIG_SYSVIPC=y
CONFIG_POSIX_MQUEUE=y
+CONFIG_FHANDLE=y
CONFIG_BSD_PROCESS_ACCT=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_RELAY=y
+CONFIG_BSD_PROCESS_ACCT_V3=y
+CONFIG_LOG_BUF_SHIFT=16
+# CONFIG_UTS_NS is not set
+# CONFIG_IPC_NS is not set
+# CONFIG_PID_NS is not set
+# CONFIG_NET_NS is not set
CONFIG_BLK_DEV_INITRD=y
-# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_SLAB=y
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
-CONFIG_ATARI=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_AMIGA_PARTITION=y
+CONFIG_MAC_PARTITION=y
+CONFIG_BSD_DISKLABEL=y
+CONFIG_MINIX_SUBPARTITION=y
+CONFIG_SOLARIS_X86_PARTITION=y
+CONFIG_UNIXWARE_DISKLABEL=y
+CONFIG_SUN_PARTITION=y
+# CONFIG_EFI_PARTITION is not set
+CONFIG_SYSV68_PARTITION=y
+CONFIG_IOSCHED_DEADLINE=m
CONFIG_M68020=y
CONFIG_M68030=y
CONFIG_M68040=y
CONFIG_M68060=y
+CONFIG_ATARI=y
+# CONFIG_COMPACTION is not set
+CONFIG_CLEANCACHE=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
CONFIG_BINFMT_AOUT=m
CONFIG_BINFMT_MISC=m
-CONFIG_STRAM_PROC=y
-CONFIG_HEARTBEAT=y
-CONFIG_PROC_HARDWARE=y
CONFIG_NET=y
CONFIG_PACKET=y
+CONFIG_PACKET_DIAG=m
CONFIG_UNIX=y
+CONFIG_UNIX_DIAG=m
+CONFIG_XFRM_MIGRATE=y
CONFIG_NET_KEY=y
-CONFIG_NET_KEY_MIGRATE=y
CONFIG_INET=y
CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_IP_PNP_RARP=y
CONFIG_NET_IPIP=m
+CONFIG_NET_IPGRE_DEMUX=m
CONFIG_NET_IPGRE=m
CONFIG_SYN_COOKIES=y
+CONFIG_NET_IPVTI=m
CONFIG_INET_AH=m
CONFIG_INET_ESP=m
CONFIG_INET_IPCOMP=m
CONFIG_INET_XFRM_MODE_TRANSPORT=m
CONFIG_INET_XFRM_MODE_TUNNEL=m
CONFIG_INET_XFRM_MODE_BEET=m
+# CONFIG_INET_LRO is not set
CONFIG_INET_DIAG=m
+CONFIG_INET_UDP_DIAG=m
CONFIG_IPV6_PRIVACY=y
CONFIG_IPV6_ROUTER_PREF=y
-CONFIG_IPV6_ROUTE_INFO=y
CONFIG_INET6_AH=m
CONFIG_INET6_ESP=m
CONFIG_INET6_IPCOMP=m
-CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION=m
-CONFIG_IPV6_TUNNEL=m
+CONFIG_IPV6_GRE=m
CONFIG_NETFILTER=y
-CONFIG_NETFILTER_NETLINK_QUEUE=m
CONFIG_NF_CONNTRACK=m
+CONFIG_NF_CONNTRACK_ZONES=y
+# CONFIG_NF_CONNTRACK_PROCFS is not set
# CONFIG_NF_CT_PROTO_DCCP is not set
CONFIG_NF_CT_PROTO_UDPLITE=m
CONFIG_NF_CONNTRACK_AMANDA=m
CONFIG_NF_CONNTRACK_H323=m
CONFIG_NF_CONNTRACK_IRC=m
CONFIG_NF_CONNTRACK_NETBIOS_NS=m
+CONFIG_NF_CONNTRACK_SNMP=m
CONFIG_NF_CONNTRACK_PPTP=m
CONFIG_NF_CONNTRACK_SANE=m
CONFIG_NF_CONNTRACK_SIP=m
CONFIG_NF_CONNTRACK_TFTP=m
+CONFIG_NETFILTER_XT_SET=m
+CONFIG_NETFILTER_XT_TARGET_CHECKSUM=m
CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
CONFIG_NETFILTER_XT_TARGET_CONNMARK=m
CONFIG_NETFILTER_XT_TARGET_DSCP=m
+CONFIG_NETFILTER_XT_TARGET_HMARK=m
+CONFIG_NETFILTER_XT_TARGET_IDLETIMER=m
+CONFIG_NETFILTER_XT_TARGET_LOG=m
CONFIG_NETFILTER_XT_TARGET_MARK=m
CONFIG_NETFILTER_XT_TARGET_NFLOG=m
CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
+CONFIG_NETFILTER_XT_TARGET_NOTRACK=m
+CONFIG_NETFILTER_XT_TARGET_TEE=m
CONFIG_NETFILTER_XT_TARGET_TRACE=m
CONFIG_NETFILTER_XT_TARGET_TCPMSS=m
CONFIG_NETFILTER_XT_TARGET_TCPOPTSTRIP=m
+CONFIG_NETFILTER_XT_MATCH_ADDRTYPE=m
+CONFIG_NETFILTER_XT_MATCH_BPF=m
CONFIG_NETFILTER_XT_MATCH_CLUSTER=m
CONFIG_NETFILTER_XT_MATCH_COMMENT=m
CONFIG_NETFILTER_XT_MATCH_CONNBYTES=m
+CONFIG_NETFILTER_XT_MATCH_CONNLABEL=m
CONFIG_NETFILTER_XT_MATCH_CONNLIMIT=m
CONFIG_NETFILTER_XT_MATCH_CONNMARK=m
CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
+CONFIG_NETFILTER_XT_MATCH_DEVGROUP=m
CONFIG_NETFILTER_XT_MATCH_DSCP=m
CONFIG_NETFILTER_XT_MATCH_ESP=m
CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m
CONFIG_NETFILTER_XT_MATCH_MAC=m
CONFIG_NETFILTER_XT_MATCH_MARK=m
CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
+CONFIG_NETFILTER_XT_MATCH_NFACCT=m
+CONFIG_NETFILTER_XT_MATCH_OSF=m
CONFIG_NETFILTER_XT_MATCH_OWNER=m
CONFIG_NETFILTER_XT_MATCH_POLICY=m
CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m
CONFIG_NETFILTER_XT_MATCH_TCPMSS=m
CONFIG_NETFILTER_XT_MATCH_TIME=m
CONFIG_NETFILTER_XT_MATCH_U32=m
+CONFIG_IP_SET=m
+CONFIG_IP_SET_BITMAP_IP=m
+CONFIG_IP_SET_BITMAP_IPMAC=m
+CONFIG_IP_SET_BITMAP_PORT=m
+CONFIG_IP_SET_HASH_IP=m
+CONFIG_IP_SET_HASH_IPPORT=m
+CONFIG_IP_SET_HASH_IPPORTIP=m
+CONFIG_IP_SET_HASH_IPPORTNET=m
+CONFIG_IP_SET_HASH_NET=m
+CONFIG_IP_SET_HASH_NETPORT=m
+CONFIG_IP_SET_HASH_NETIFACE=m
+CONFIG_IP_SET_LIST_SET=m
CONFIG_NF_CONNTRACK_IPV4=m
-CONFIG_IP_NF_QUEUE=m
CONFIG_IP_NF_IPTABLES=m
-CONFIG_IP_NF_MATCH_ADDRTYPE=m
CONFIG_IP_NF_MATCH_AH=m
CONFIG_IP_NF_MATCH_ECN=m
+CONFIG_IP_NF_MATCH_RPFILTER=m
CONFIG_IP_NF_MATCH_TTL=m
CONFIG_IP_NF_FILTER=m
CONFIG_IP_NF_TARGET_REJECT=m
-CONFIG_IP_NF_TARGET_LOG=m
CONFIG_IP_NF_TARGET_ULOG=m
-CONFIG_NF_NAT=m
+CONFIG_NF_NAT_IPV4=m
CONFIG_IP_NF_TARGET_MASQUERADE=m
CONFIG_IP_NF_TARGET_NETMAP=m
CONFIG_IP_NF_TARGET_REDIRECT=m
-CONFIG_NF_NAT_SNMP_BASIC=m
CONFIG_IP_NF_MANGLE=m
CONFIG_IP_NF_TARGET_CLUSTERIP=m
CONFIG_IP_NF_TARGET_ECN=m
CONFIG_IP_NF_ARPFILTER=m
CONFIG_IP_NF_ARP_MANGLE=m
CONFIG_NF_CONNTRACK_IPV6=m
-CONFIG_IP6_NF_QUEUE=m
CONFIG_IP6_NF_IPTABLES=m
CONFIG_IP6_NF_MATCH_AH=m
CONFIG_IP6_NF_MATCH_EUI64=m
CONFIG_IP6_NF_MATCH_HL=m
CONFIG_IP6_NF_MATCH_IPV6HEADER=m
CONFIG_IP6_NF_MATCH_MH=m
+CONFIG_IP6_NF_MATCH_RPFILTER=m
CONFIG_IP6_NF_MATCH_RT=m
CONFIG_IP6_NF_TARGET_HL=m
-CONFIG_IP6_NF_TARGET_LOG=m
CONFIG_IP6_NF_FILTER=m
CONFIG_IP6_NF_TARGET_REJECT=m
CONFIG_IP6_NF_MANGLE=m
CONFIG_IP6_NF_RAW=m
+CONFIG_NF_NAT_IPV6=m
+CONFIG_IP6_NF_TARGET_MASQUERADE=m
+CONFIG_IP6_NF_TARGET_NPT=m
CONFIG_IP_DCCP=m
# CONFIG_IP_DCCP_CCID3 is not set
+CONFIG_SCTP_COOKIE_HMAC_SHA1=y
+CONFIG_RDS=m
+CONFIG_RDS_TCP=m
+CONFIG_L2TP=m
CONFIG_ATALK=m
+CONFIG_BATMAN_ADV=m
+CONFIG_BATMAN_ADV_DAT=y
+# CONFIG_WIRELESS is not set
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
# CONFIG_FIRMWARE_IN_KERNEL is not set
+# CONFIG_FW_LOADER_USER_HELPER is not set
CONFIG_CONNECTOR=m
CONFIG_PARPORT=m
CONFIG_PARPORT_ATARI=m
CONFIG_ATARI_FLOPPY=y
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_CRYPTOLOOP=m
+CONFIG_BLK_DEV_DRBD=m
CONFIG_BLK_DEV_NBD=m
CONFIG_BLK_DEV_RAM=y
CONFIG_CDROM_PKTCDVD=m
CONFIG_ATA_OVER_ETH=m
CONFIG_IDE=y
+CONFIG_IDE_GD_ATAPI=y
CONFIG_BLK_DEV_IDECD=y
CONFIG_BLK_DEV_FALCON_IDE=y
CONFIG_RAID_ATTRS=m
CONFIG_BLK_DEV_SR_VENDOR=y
CONFIG_CHR_DEV_SG=m
CONFIG_SCSI_CONSTANTS=y
-CONFIG_SCSI_SAS_LIBSAS=m
-# CONFIG_SCSI_SAS_LIBSAS_DEBUG is not set
-CONFIG_SCSI_SRP_ATTRS=m
-CONFIG_SCSI_SRP_TGT_ATTRS=y
+CONFIG_SCSI_SAS_ATTRS=m
CONFIG_ISCSI_TCP=m
+CONFIG_ISCSI_BOOT_SYSFS=m
CONFIG_ATARI_SCSI=y
CONFIG_MD=y
-CONFIG_BLK_DEV_MD=m
CONFIG_MD_LINEAR=m
CONFIG_MD_RAID0=m
-CONFIG_MD_RAID1=m
-CONFIG_MD_RAID456=m
CONFIG_BLK_DEV_DM=m
CONFIG_DM_CRYPT=m
CONFIG_DM_SNAPSHOT=m
+CONFIG_DM_THIN_PROVISIONING=m
+CONFIG_DM_CACHE=m
CONFIG_DM_MIRROR=m
+CONFIG_DM_RAID=m
CONFIG_DM_ZERO=m
CONFIG_DM_MULTIPATH=m
CONFIG_DM_UEVENT=y
+CONFIG_TARGET_CORE=m
+CONFIG_TCM_IBLOCK=m
+CONFIG_TCM_FILEIO=m
+CONFIG_TCM_PSCSI=m
CONFIG_NETDEVICES=y
CONFIG_DUMMY=m
-CONFIG_MACVLAN=m
CONFIG_EQUALIZER=m
-CONFIG_VETH=m
-CONFIG_NET_ETHERNET=y
CONFIG_MII=y
+CONFIG_NET_TEAM=m
+CONFIG_NET_TEAM_MODE_BROADCAST=m
+CONFIG_NET_TEAM_MODE_ROUNDROBIN=m
+CONFIG_NET_TEAM_MODE_ACTIVEBACKUP=m
+CONFIG_NET_TEAM_MODE_LOADBALANCE=m
+CONFIG_VXLAN=m
+CONFIG_NETCONSOLE=m
+CONFIG_NETCONSOLE_DYNAMIC=y
+CONFIG_VETH=m
CONFIG_ATARILANCE=y
-# CONFIG_NETDEV_1000 is not set
-# CONFIG_NETDEV_10000 is not set
+# CONFIG_NET_CADENCE is not set
+# CONFIG_NET_VENDOR_BROADCOM is not set
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_WIZNET is not set
CONFIG_PPP=m
-CONFIG_PPP_FILTER=y
-CONFIG_PPP_ASYNC=m
-CONFIG_PPP_SYNC_TTY=m
-CONFIG_PPP_DEFLATE=m
CONFIG_PPP_BSDCOMP=m
+CONFIG_PPP_DEFLATE=m
+CONFIG_PPP_FILTER=y
CONFIG_PPP_MPPE=m
CONFIG_PPPOE=m
+CONFIG_PPTP=m
+CONFIG_PPPOL2TP=m
+CONFIG_PPP_ASYNC=m
+CONFIG_PPP_SYNC_TTY=m
CONFIG_SLIP=m
CONFIG_SLIP_COMPRESSED=y
CONFIG_SLIP_SMART=y
CONFIG_SLIP_MODE_SLIP6=y
-CONFIG_NETCONSOLE=m
-CONFIG_NETCONSOLE_DYNAMIC=y
-CONFIG_INPUT_FF_MEMLESS=m
+# CONFIG_WLAN is not set
+CONFIG_INPUT_EVDEV=m
CONFIG_KEYBOARD_ATARI=y
# CONFIG_KEYBOARD_ATKBD is not set
-CONFIG_MOUSE_PS2=m
+# CONFIG_MOUSE_PS2 is not set
CONFIG_MOUSE_ATARI=m
CONFIG_INPUT_MISC=y
CONFIG_INPUT_M68K_BEEP=m
-# CONFIG_SERIO_SERPORT is not set
+# CONFIG_SERIO is not set
CONFIG_VT_HW_CONSOLE_BINDING=y
+# CONFIG_LEGACY_PTYS is not set
# CONFIG_DEVKMEM is not set
CONFIG_PRINTER=m
# CONFIG_HW_RANDOM is not set
-CONFIG_GEN_RTC=m
-CONFIG_GEN_RTC_X=y
+CONFIG_NTP_PPS=y
+CONFIG_PPS_CLIENT_LDISC=m
+CONFIG_PPS_CLIENT_PARPORT=m
+CONFIG_PTP_1588_CLOCK=m
# CONFIG_HWMON is not set
CONFIG_FB=y
CONFIG_FB_ATARI=y
CONFIG_DMASOUND_ATARI=m
CONFIG_HID=m
CONFIG_HIDRAW=y
-# CONFIG_USB_SUPPORT is not set
+CONFIG_UHID=m
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_GENERIC=m
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_HEARTBEAT=y
+CONFIG_PROC_HARDWARE=y
+CONFIG_NATFEAT=y
+CONFIG_NFBLOCK=y
+CONFIG_NFCON=y
+CONFIG_NFETH=y
CONFIG_ATARI_DSP56K=m
CONFIG_EXT2_FS=y
CONFIG_EXT3_FS=y
# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
# CONFIG_EXT3_FS_XATTR is not set
+CONFIG_EXT4_FS=y
CONFIG_REISERFS_FS=m
CONFIG_JFS_FS=m
CONFIG_XFS_FS=m
CONFIG_OCFS2_FS=m
-# CONFIG_OCFS2_FS_STATS is not set
# CONFIG_OCFS2_DEBUG_MASKLOG is not set
+CONFIG_FANOTIFY=y
CONFIG_QUOTA_NETLINK_INTERFACE=y
# CONFIG_PRINT_QUOTA_WARNING is not set
-CONFIG_AUTOFS_FS=m
CONFIG_AUTOFS4_FS=m
CONFIG_FUSE_FS=m
+CONFIG_CUSE=m
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
CONFIG_UDF_FS=m
-CONFIG_MSDOS_FS=y
+CONFIG_MSDOS_FS=m
CONFIG_VFAT_FS=m
CONFIG_PROC_KCORE=y
CONFIG_TMPFS=y
CONFIG_AFFS_FS=m
+CONFIG_ECRYPT_FS=m
+CONFIG_ECRYPT_FS_MESSAGING=y
CONFIG_HFS_FS=m
CONFIG_HFSPLUS_FS=m
CONFIG_CRAMFS=m
CONFIG_SQUASHFS=m
-CONFIG_MINIX_FS=y
+CONFIG_SQUASHFS_LZO=y
+CONFIG_MINIX_FS=m
+CONFIG_OMFS_FS=m
CONFIG_HPFS_FS=m
+CONFIG_QNX4FS_FS=m
+CONFIG_QNX6FS_FS=m
CONFIG_SYSV_FS=m
CONFIG_UFS_FS=m
CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
CONFIG_NFS_V4=y
+CONFIG_NFS_SWAP=y
+CONFIG_ROOT_NFS=y
CONFIG_NFSD=m
CONFIG_NFSD_V3=y
-CONFIG_SMB_FS=m
-CONFIG_SMB_NLS_DEFAULT=y
+CONFIG_CIFS=m
+# CONFIG_CIFS_DEBUG is not set
CONFIG_CODA_FS=m
CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_CODEPAGE_737=m
CONFIG_NLS_ISO8859_15=m
CONFIG_NLS_KOI8_R=m
CONFIG_NLS_KOI8_U=m
+CONFIG_NLS_MAC_ROMAN=m
+CONFIG_NLS_MAC_CELTIC=m
+CONFIG_NLS_MAC_CENTEURO=m
+CONFIG_NLS_MAC_CROATIAN=m
+CONFIG_NLS_MAC_CYRILLIC=m
+CONFIG_NLS_MAC_GAELIC=m
+CONFIG_NLS_MAC_GREEK=m
+CONFIG_NLS_MAC_ICELAND=m
+CONFIG_NLS_MAC_INUIT=m
+CONFIG_NLS_MAC_ROMANIAN=m
+CONFIG_NLS_MAC_TURKISH=m
CONFIG_DLM=m
CONFIG_MAGIC_SYSRQ=y
-# CONFIG_RCU_CPU_STALL_DETECTOR is not set
-CONFIG_SYSCTL_SYSCALL_CHECK=y
+CONFIG_ASYNC_RAID6_TEST=m
+CONFIG_ENCRYPTED_KEYS=m
+CONFIG_CRYPTO_MANAGER=y
+CONFIG_CRYPTO_USER=m
CONFIG_CRYPTO_NULL=m
CONFIG_CRYPTO_CRYPTD=m
CONFIG_CRYPTO_TEST=m
CONFIG_CRYPTO_LRW=m
CONFIG_CRYPTO_PCBC=m
CONFIG_CRYPTO_XTS=m
-CONFIG_CRYPTO_HMAC=y
CONFIG_CRYPTO_XCBC=m
-CONFIG_CRYPTO_MD4=m
+CONFIG_CRYPTO_VMAC=m
CONFIG_CRYPTO_MICHAEL_MIC=m
CONFIG_CRYPTO_RMD128=m
CONFIG_CRYPTO_RMD160=m
CONFIG_CRYPTO_RMD256=m
CONFIG_CRYPTO_RMD320=m
-CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
CONFIG_CRYPTO_TGR192=m
CONFIG_CRYPTO_WP512=m
-CONFIG_CRYPTO_AES=m
CONFIG_CRYPTO_ANUBIS=m
CONFIG_CRYPTO_BLOWFISH=m
CONFIG_CRYPTO_CAMELLIA=m
CONFIG_CRYPTO_ZLIB=m
CONFIG_CRYPTO_LZO=m
# CONFIG_CRYPTO_ANSI_CPRNG is not set
+CONFIG_CRYPTO_USER_API_HASH=m
+CONFIG_CRYPTO_USER_API_SKCIPHER=m
# CONFIG_CRYPTO_HW is not set
-CONFIG_CRC16=y
CONFIG_CRC_T10DIF=y
+CONFIG_XZ_DEC_X86=y
+CONFIG_XZ_DEC_POWERPC=y
+CONFIG_XZ_DEC_IA64=y
+CONFIG_XZ_DEC_ARM=y
+CONFIG_XZ_DEC_ARMTHUMB=y
+CONFIG_XZ_DEC_SPARC=y
+CONFIG_XZ_DEC_TEST=m
-CONFIG_EXPERIMENTAL=y
CONFIG_LOCALVERSION="-bvme6000"
CONFIG_SYSVIPC=y
CONFIG_POSIX_MQUEUE=y
+CONFIG_FHANDLE=y
CONFIG_BSD_PROCESS_ACCT=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_RELAY=y
+CONFIG_BSD_PROCESS_ACCT_V3=y
+CONFIG_LOG_BUF_SHIFT=16
+# CONFIG_UTS_NS is not set
+# CONFIG_IPC_NS is not set
+# CONFIG_PID_NS is not set
+# CONFIG_NET_NS is not set
CONFIG_BLK_DEV_INITRD=y
-# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_SLAB=y
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
-CONFIG_VME=y
-CONFIG_BVME6000=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_AMIGA_PARTITION=y
+CONFIG_ATARI_PARTITION=y
+CONFIG_MAC_PARTITION=y
+CONFIG_BSD_DISKLABEL=y
+CONFIG_MINIX_SUBPARTITION=y
+CONFIG_SOLARIS_X86_PARTITION=y
+CONFIG_UNIXWARE_DISKLABEL=y
+CONFIG_SUN_PARTITION=y
+# CONFIG_EFI_PARTITION is not set
+CONFIG_IOSCHED_DEADLINE=m
CONFIG_M68040=y
CONFIG_M68060=y
+CONFIG_VME=y
+CONFIG_BVME6000=y
+# CONFIG_COMPACTION is not set
+CONFIG_CLEANCACHE=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
CONFIG_BINFMT_AOUT=m
CONFIG_BINFMT_MISC=m
-CONFIG_PROC_HARDWARE=y
CONFIG_NET=y
CONFIG_PACKET=y
+CONFIG_PACKET_DIAG=m
CONFIG_UNIX=y
+CONFIG_UNIX_DIAG=m
+CONFIG_XFRM_MIGRATE=y
CONFIG_NET_KEY=y
-CONFIG_NET_KEY_MIGRATE=y
CONFIG_INET=y
CONFIG_IP_PNP=y
CONFIG_IP_PNP_DHCP=y
CONFIG_IP_PNP_BOOTP=y
CONFIG_IP_PNP_RARP=y
CONFIG_NET_IPIP=m
+CONFIG_NET_IPGRE_DEMUX=m
CONFIG_NET_IPGRE=m
CONFIG_SYN_COOKIES=y
+CONFIG_NET_IPVTI=m
CONFIG_INET_AH=m
CONFIG_INET_ESP=m
CONFIG_INET_IPCOMP=m
CONFIG_INET_XFRM_MODE_TRANSPORT=m
CONFIG_INET_XFRM_MODE_TUNNEL=m
CONFIG_INET_XFRM_MODE_BEET=m
+# CONFIG_INET_LRO is not set
CONFIG_INET_DIAG=m
+CONFIG_INET_UDP_DIAG=m
CONFIG_IPV6_PRIVACY=y
CONFIG_IPV6_ROUTER_PREF=y
-CONFIG_IPV6_ROUTE_INFO=y
CONFIG_INET6_AH=m
CONFIG_INET6_ESP=m
CONFIG_INET6_IPCOMP=m
-CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION=m
-CONFIG_IPV6_TUNNEL=m
+CONFIG_IPV6_GRE=m
CONFIG_NETFILTER=y
-CONFIG_NETFILTER_NETLINK_QUEUE=m
CONFIG_NF_CONNTRACK=m
+CONFIG_NF_CONNTRACK_ZONES=y
+# CONFIG_NF_CONNTRACK_PROCFS is not set
# CONFIG_NF_CT_PROTO_DCCP is not set
CONFIG_NF_CT_PROTO_UDPLITE=m
CONFIG_NF_CONNTRACK_AMANDA=m
CONFIG_NF_CONNTRACK_H323=m
CONFIG_NF_CONNTRACK_IRC=m
CONFIG_NF_CONNTRACK_NETBIOS_NS=m
+CONFIG_NF_CONNTRACK_SNMP=m
CONFIG_NF_CONNTRACK_PPTP=m
CONFIG_NF_CONNTRACK_SANE=m
CONFIG_NF_CONNTRACK_SIP=m
CONFIG_NF_CONNTRACK_TFTP=m
+CONFIG_NETFILTER_XT_SET=m
+CONFIG_NETFILTER_XT_TARGET_CHECKSUM=m
CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
CONFIG_NETFILTER_XT_TARGET_CONNMARK=m
CONFIG_NETFILTER_XT_TARGET_DSCP=m
+CONFIG_NETFILTER_XT_TARGET_HMARK=m
+CONFIG_NETFILTER_XT_TARGET_IDLETIMER=m
+CONFIG_NETFILTER_XT_TARGET_LOG=m
CONFIG_NETFILTER_XT_TARGET_MARK=m
CONFIG_NETFILTER_XT_TARGET_NFLOG=m
CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
+CONFIG_NETFILTER_XT_TARGET_NOTRACK=m
+CONFIG_NETFILTER_XT_TARGET_TEE=m
CONFIG_NETFILTER_XT_TARGET_TRACE=m
CONFIG_NETFILTER_XT_TARGET_TCPMSS=m
CONFIG_NETFILTER_XT_TARGET_TCPOPTSTRIP=m
+CONFIG_NETFILTER_XT_MATCH_ADDRTYPE=m
+CONFIG_NETFILTER_XT_MATCH_BPF=m
CONFIG_NETFILTER_XT_MATCH_CLUSTER=m
CONFIG_NETFILTER_XT_MATCH_COMMENT=m
CONFIG_NETFILTER_XT_MATCH_CONNBYTES=m
+CONFIG_NETFILTER_XT_MATCH_CONNLABEL=m
CONFIG_NETFILTER_XT_MATCH_CONNLIMIT=m
CONFIG_NETFILTER_XT_MATCH_CONNMARK=m
CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
+CONFIG_NETFILTER_XT_MATCH_DEVGROUP=m
CONFIG_NETFILTER_XT_MATCH_DSCP=m
CONFIG_NETFILTER_XT_MATCH_ESP=m
CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m
CONFIG_NETFILTER_XT_MATCH_MAC=m
CONFIG_NETFILTER_XT_MATCH_MARK=m
CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
+CONFIG_NETFILTER_XT_MATCH_NFACCT=m
+CONFIG_NETFILTER_XT_MATCH_OSF=m
CONFIG_NETFILTER_XT_MATCH_OWNER=m
CONFIG_NETFILTER_XT_MATCH_POLICY=m
CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m
CONFIG_NETFILTER_XT_MATCH_TCPMSS=m
CONFIG_NETFILTER_XT_MATCH_TIME=m
CONFIG_NETFILTER_XT_MATCH_U32=m
+CONFIG_IP_SET=m
+CONFIG_IP_SET_BITMAP_IP=m
+CONFIG_IP_SET_BITMAP_IPMAC=m
+CONFIG_IP_SET_BITMAP_PORT=m
+CONFIG_IP_SET_HASH_IP=m
+CONFIG_IP_SET_HASH_IPPORT=m
+CONFIG_IP_SET_HASH_IPPORTIP=m
+CONFIG_IP_SET_HASH_IPPORTNET=m
+CONFIG_IP_SET_HASH_NET=m
+CONFIG_IP_SET_HASH_NETPORT=m
+CONFIG_IP_SET_HASH_NETIFACE=m
+CONFIG_IP_SET_LIST_SET=m
CONFIG_NF_CONNTRACK_IPV4=m
-CONFIG_IP_NF_QUEUE=m
CONFIG_IP_NF_IPTABLES=m
-CONFIG_IP_NF_MATCH_ADDRTYPE=m
CONFIG_IP_NF_MATCH_AH=m
CONFIG_IP_NF_MATCH_ECN=m
+CONFIG_IP_NF_MATCH_RPFILTER=m
CONFIG_IP_NF_MATCH_TTL=m
CONFIG_IP_NF_FILTER=m
CONFIG_IP_NF_TARGET_REJECT=m
-CONFIG_IP_NF_TARGET_LOG=m
CONFIG_IP_NF_TARGET_ULOG=m
-CONFIG_NF_NAT=m
+CONFIG_NF_NAT_IPV4=m
CONFIG_IP_NF_TARGET_MASQUERADE=m
CONFIG_IP_NF_TARGET_NETMAP=m
CONFIG_IP_NF_TARGET_REDIRECT=m
-CONFIG_NF_NAT_SNMP_BASIC=m
CONFIG_IP_NF_MANGLE=m
CONFIG_IP_NF_TARGET_CLUSTERIP=m
CONFIG_IP_NF_TARGET_ECN=m
CONFIG_IP_NF_ARPFILTER=m
CONFIG_IP_NF_ARP_MANGLE=m
CONFIG_NF_CONNTRACK_IPV6=m
-CONFIG_IP6_NF_QUEUE=m
CONFIG_IP6_NF_IPTABLES=m
CONFIG_IP6_NF_MATCH_AH=m
CONFIG_IP6_NF_MATCH_EUI64=m
CONFIG_IP6_NF_MATCH_HL=m
CONFIG_IP6_NF_MATCH_IPV6HEADER=m
CONFIG_IP6_NF_MATCH_MH=m
+CONFIG_IP6_NF_MATCH_RPFILTER=m
CONFIG_IP6_NF_MATCH_RT=m
CONFIG_IP6_NF_TARGET_HL=m
-CONFIG_IP6_NF_TARGET_LOG=m
CONFIG_IP6_NF_FILTER=m
CONFIG_IP6_NF_TARGET_REJECT=m
CONFIG_IP6_NF_MANGLE=m
CONFIG_IP6_NF_RAW=m
+CONFIG_NF_NAT_IPV6=m
+CONFIG_IP6_NF_TARGET_MASQUERADE=m
+CONFIG_IP6_NF_TARGET_NPT=m
CONFIG_IP_DCCP=m
# CONFIG_IP_DCCP_CCID3 is not set
+CONFIG_SCTP_COOKIE_HMAC_SHA1=y
+CONFIG_RDS=m
+CONFIG_RDS_TCP=m
+CONFIG_L2TP=m
CONFIG_ATALK=m
+CONFIG_BATMAN_ADV=m
+CONFIG_BATMAN_ADV_DAT=y
+# CONFIG_WIRELESS is not set
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
# CONFIG_FIRMWARE_IN_KERNEL is not set
+# CONFIG_FW_LOADER_USER_HELPER is not set
CONFIG_CONNECTOR=m
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_CRYPTOLOOP=m
+CONFIG_BLK_DEV_DRBD=m
CONFIG_BLK_DEV_NBD=m
CONFIG_BLK_DEV_RAM=y
CONFIG_CDROM_PKTCDVD=m
CONFIG_BLK_DEV_SR_VENDOR=y
CONFIG_CHR_DEV_SG=m
CONFIG_SCSI_CONSTANTS=y
-CONFIG_SCSI_SAS_LIBSAS=m
-# CONFIG_SCSI_SAS_LIBSAS_DEBUG is not set
-CONFIG_SCSI_SRP_ATTRS=m
-CONFIG_SCSI_SRP_TGT_ATTRS=y
+CONFIG_SCSI_SAS_ATTRS=m
CONFIG_ISCSI_TCP=m
+CONFIG_ISCSI_BOOT_SYSFS=m
CONFIG_BVME6000_SCSI=y
CONFIG_MD=y
-CONFIG_BLK_DEV_MD=m
CONFIG_MD_LINEAR=m
CONFIG_MD_RAID0=m
-CONFIG_MD_RAID1=m
-CONFIG_MD_RAID456=m
CONFIG_BLK_DEV_DM=m
CONFIG_DM_CRYPT=m
CONFIG_DM_SNAPSHOT=m
+CONFIG_DM_THIN_PROVISIONING=m
+CONFIG_DM_CACHE=m
CONFIG_DM_MIRROR=m
+CONFIG_DM_RAID=m
CONFIG_DM_ZERO=m
CONFIG_DM_MULTIPATH=m
CONFIG_DM_UEVENT=y
+CONFIG_TARGET_CORE=m
+CONFIG_TCM_IBLOCK=m
+CONFIG_TCM_FILEIO=m
+CONFIG_TCM_PSCSI=m
CONFIG_NETDEVICES=y
CONFIG_DUMMY=m
-CONFIG_MACVLAN=m
CONFIG_EQUALIZER=m
+CONFIG_NET_TEAM=m
+CONFIG_NET_TEAM_MODE_BROADCAST=m
+CONFIG_NET_TEAM_MODE_ROUNDROBIN=m
+CONFIG_NET_TEAM_MODE_ACTIVEBACKUP=m
+CONFIG_NET_TEAM_MODE_LOADBALANCE=m
+CONFIG_VXLAN=m
+CONFIG_NETCONSOLE=m
+CONFIG_NETCONSOLE_DYNAMIC=y
CONFIG_VETH=m
-CONFIG_NET_ETHERNET=y
+# CONFIG_NET_CADENCE is not set
+# CONFIG_NET_VENDOR_BROADCOM is not set
CONFIG_BVME6000_NET=y
-# CONFIG_NETDEV_1000 is not set
-# CONFIG_NETDEV_10000 is not set
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_WIZNET is not set
CONFIG_PPP=m
-CONFIG_PPP_FILTER=y
-CONFIG_PPP_ASYNC=m
-CONFIG_PPP_SYNC_TTY=m
-CONFIG_PPP_DEFLATE=m
CONFIG_PPP_BSDCOMP=m
+CONFIG_PPP_DEFLATE=m
+CONFIG_PPP_FILTER=y
CONFIG_PPP_MPPE=m
CONFIG_PPPOE=m
+CONFIG_PPTP=m
+CONFIG_PPPOL2TP=m
+CONFIG_PPP_ASYNC=m
+CONFIG_PPP_SYNC_TTY=m
CONFIG_SLIP=m
CONFIG_SLIP_COMPRESSED=y
CONFIG_SLIP_SMART=y
CONFIG_SLIP_MODE_SLIP6=y
-CONFIG_NETCONSOLE=m
-CONFIG_NETCONSOLE_DYNAMIC=y
-CONFIG_INPUT_FF_MEMLESS=m
+# CONFIG_WLAN is not set
+CONFIG_INPUT_EVDEV=m
# CONFIG_KEYBOARD_ATKBD is not set
-CONFIG_MOUSE_PS2=m
-CONFIG_MOUSE_SERIAL=m
-CONFIG_SERIO=m
-# CONFIG_SERIO_SERPORT is not set
+# CONFIG_MOUSE_PS2 is not set
+# CONFIG_SERIO is not set
CONFIG_VT_HW_CONSOLE_BINDING=y
+# CONFIG_LEGACY_PTYS is not set
# CONFIG_DEVKMEM is not set
# CONFIG_HW_RANDOM is not set
-CONFIG_GEN_RTC=m
-CONFIG_GEN_RTC_X=y
+CONFIG_NTP_PPS=y
+CONFIG_PPS_CLIENT_LDISC=m
+CONFIG_PTP_1588_CLOCK=m
# CONFIG_HWMON is not set
CONFIG_HID=m
CONFIG_HIDRAW=y
+CONFIG_UHID=m
+# CONFIG_HID_GENERIC is not set
# CONFIG_USB_SUPPORT is not set
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_GENERIC=m
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_PROC_HARDWARE=y
CONFIG_EXT2_FS=y
CONFIG_EXT3_FS=y
# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
# CONFIG_EXT3_FS_XATTR is not set
+CONFIG_EXT4_FS=y
CONFIG_REISERFS_FS=m
CONFIG_JFS_FS=m
CONFIG_XFS_FS=m
CONFIG_OCFS2_FS=m
-# CONFIG_OCFS2_FS_STATS is not set
# CONFIG_OCFS2_DEBUG_MASKLOG is not set
+CONFIG_FANOTIFY=y
CONFIG_QUOTA_NETLINK_INTERFACE=y
# CONFIG_PRINT_QUOTA_WARNING is not set
-CONFIG_AUTOFS_FS=m
CONFIG_AUTOFS4_FS=m
CONFIG_FUSE_FS=m
+CONFIG_CUSE=m
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
CONFIG_UDF_FS=m
-CONFIG_MSDOS_FS=y
+CONFIG_MSDOS_FS=m
CONFIG_VFAT_FS=m
CONFIG_PROC_KCORE=y
CONFIG_TMPFS=y
CONFIG_AFFS_FS=m
+CONFIG_ECRYPT_FS=m
+CONFIG_ECRYPT_FS_MESSAGING=y
CONFIG_HFS_FS=m
CONFIG_HFSPLUS_FS=m
CONFIG_CRAMFS=m
CONFIG_SQUASHFS=m
-CONFIG_MINIX_FS=y
+CONFIG_SQUASHFS_LZO=y
+CONFIG_MINIX_FS=m
+CONFIG_OMFS_FS=m
CONFIG_HPFS_FS=m
+CONFIG_QNX4FS_FS=m
+CONFIG_QNX6FS_FS=m
CONFIG_SYSV_FS=m
CONFIG_UFS_FS=m
CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
CONFIG_NFS_V4=y
+CONFIG_NFS_SWAP=y
CONFIG_ROOT_NFS=y
CONFIG_NFSD=m
CONFIG_NFSD_V3=y
-CONFIG_SMB_FS=m
-CONFIG_SMB_NLS_DEFAULT=y
+CONFIG_CIFS=m
+# CONFIG_CIFS_DEBUG is not set
CONFIG_CODA_FS=m
CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_CODEPAGE_737=m
CONFIG_NLS_ISO8859_15=m
CONFIG_NLS_KOI8_R=m
CONFIG_NLS_KOI8_U=m
+CONFIG_NLS_MAC_ROMAN=m
+CONFIG_NLS_MAC_CELTIC=m
+CONFIG_NLS_MAC_CENTEURO=m
+CONFIG_NLS_MAC_CROATIAN=m
+CONFIG_NLS_MAC_CYRILLIC=m
+CONFIG_NLS_MAC_GAELIC=m
+CONFIG_NLS_MAC_GREEK=m
+CONFIG_NLS_MAC_ICELAND=m
+CONFIG_NLS_MAC_INUIT=m
+CONFIG_NLS_MAC_ROMANIAN=m
+CONFIG_NLS_MAC_TURKISH=m
CONFIG_DLM=m
CONFIG_MAGIC_SYSRQ=y
-# CONFIG_RCU_CPU_STALL_DETECTOR is not set
-CONFIG_SYSCTL_SYSCALL_CHECK=y
+CONFIG_ASYNC_RAID6_TEST=m
+CONFIG_ENCRYPTED_KEYS=m
+CONFIG_CRYPTO_MANAGER=y
+CONFIG_CRYPTO_USER=m
CONFIG_CRYPTO_NULL=m
CONFIG_CRYPTO_CRYPTD=m
CONFIG_CRYPTO_TEST=m
CONFIG_CRYPTO_LRW=m
CONFIG_CRYPTO_PCBC=m
CONFIG_CRYPTO_XTS=m
-CONFIG_CRYPTO_HMAC=y
CONFIG_CRYPTO_XCBC=m
-CONFIG_CRYPTO_MD4=m
+CONFIG_CRYPTO_VMAC=m
CONFIG_CRYPTO_MICHAEL_MIC=m
CONFIG_CRYPTO_RMD128=m
CONFIG_CRYPTO_RMD160=m
CONFIG_CRYPTO_RMD256=m
CONFIG_CRYPTO_RMD320=m
-CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
CONFIG_CRYPTO_TGR192=m
CONFIG_CRYPTO_WP512=m
-CONFIG_CRYPTO_AES=m
CONFIG_CRYPTO_ANUBIS=m
CONFIG_CRYPTO_BLOWFISH=m
CONFIG_CRYPTO_CAMELLIA=m
CONFIG_CRYPTO_ZLIB=m
CONFIG_CRYPTO_LZO=m
# CONFIG_CRYPTO_ANSI_CPRNG is not set
+CONFIG_CRYPTO_USER_API_HASH=m
+CONFIG_CRYPTO_USER_API_SKCIPHER=m
# CONFIG_CRYPTO_HW is not set
-CONFIG_CRC16=m
CONFIG_CRC_T10DIF=y
-CONFIG_CRC32=m
+CONFIG_XZ_DEC_X86=y
+CONFIG_XZ_DEC_POWERPC=y
+CONFIG_XZ_DEC_IA64=y
+CONFIG_XZ_DEC_ARM=y
+CONFIG_XZ_DEC_ARMTHUMB=y
+CONFIG_XZ_DEC_SPARC=y
+CONFIG_XZ_DEC_TEST=m
-CONFIG_EXPERIMENTAL=y
CONFIG_LOCALVERSION="-hp300"
CONFIG_SYSVIPC=y
CONFIG_POSIX_MQUEUE=y
+CONFIG_FHANDLE=y
CONFIG_BSD_PROCESS_ACCT=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_RELAY=y
+CONFIG_BSD_PROCESS_ACCT_V3=y
+CONFIG_LOG_BUF_SHIFT=16
+# CONFIG_UTS_NS is not set
+# CONFIG_IPC_NS is not set
+# CONFIG_PID_NS is not set
+# CONFIG_NET_NS is not set
CONFIG_BLK_DEV_INITRD=y
-# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_SLAB=y
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
-CONFIG_HP300=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_AMIGA_PARTITION=y
+CONFIG_ATARI_PARTITION=y
+CONFIG_MAC_PARTITION=y
+CONFIG_BSD_DISKLABEL=y
+CONFIG_MINIX_SUBPARTITION=y
+CONFIG_SOLARIS_X86_PARTITION=y
+CONFIG_UNIXWARE_DISKLABEL=y
+CONFIG_SUN_PARTITION=y
+# CONFIG_EFI_PARTITION is not set
+CONFIG_SYSV68_PARTITION=y
+CONFIG_IOSCHED_DEADLINE=m
CONFIG_M68020=y
CONFIG_M68030=y
CONFIG_M68040=y
CONFIG_M68060=y
+CONFIG_HP300=y
+# CONFIG_COMPACTION is not set
+CONFIG_CLEANCACHE=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
CONFIG_BINFMT_AOUT=m
CONFIG_BINFMT_MISC=m
-CONFIG_PROC_HARDWARE=y
CONFIG_NET=y
CONFIG_PACKET=y
+CONFIG_PACKET_DIAG=m
CONFIG_UNIX=y
+CONFIG_UNIX_DIAG=m
+CONFIG_XFRM_MIGRATE=y
CONFIG_NET_KEY=y
-CONFIG_NET_KEY_MIGRATE=y
CONFIG_INET=y
CONFIG_IP_PNP=y
CONFIG_IP_PNP_DHCP=y
CONFIG_IP_PNP_BOOTP=y
CONFIG_IP_PNP_RARP=y
CONFIG_NET_IPIP=m
+CONFIG_NET_IPGRE_DEMUX=m
CONFIG_NET_IPGRE=m
CONFIG_SYN_COOKIES=y
+CONFIG_NET_IPVTI=m
CONFIG_INET_AH=m
CONFIG_INET_ESP=m
CONFIG_INET_IPCOMP=m
CONFIG_INET_XFRM_MODE_TRANSPORT=m
CONFIG_INET_XFRM_MODE_TUNNEL=m
CONFIG_INET_XFRM_MODE_BEET=m
+# CONFIG_INET_LRO is not set
CONFIG_INET_DIAG=m
+CONFIG_INET_UDP_DIAG=m
CONFIG_IPV6_PRIVACY=y
CONFIG_IPV6_ROUTER_PREF=y
-CONFIG_IPV6_ROUTE_INFO=y
CONFIG_INET6_AH=m
CONFIG_INET6_ESP=m
CONFIG_INET6_IPCOMP=m
-CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION=m
-CONFIG_IPV6_TUNNEL=m
+CONFIG_IPV6_GRE=m
CONFIG_NETFILTER=y
-CONFIG_NETFILTER_NETLINK_QUEUE=m
CONFIG_NF_CONNTRACK=m
+CONFIG_NF_CONNTRACK_ZONES=y
+# CONFIG_NF_CONNTRACK_PROCFS is not set
# CONFIG_NF_CT_PROTO_DCCP is not set
CONFIG_NF_CT_PROTO_UDPLITE=m
CONFIG_NF_CONNTRACK_AMANDA=m
CONFIG_NF_CONNTRACK_H323=m
CONFIG_NF_CONNTRACK_IRC=m
CONFIG_NF_CONNTRACK_NETBIOS_NS=m
+CONFIG_NF_CONNTRACK_SNMP=m
CONFIG_NF_CONNTRACK_PPTP=m
CONFIG_NF_CONNTRACK_SANE=m
CONFIG_NF_CONNTRACK_SIP=m
CONFIG_NF_CONNTRACK_TFTP=m
+CONFIG_NETFILTER_XT_SET=m
+CONFIG_NETFILTER_XT_TARGET_CHECKSUM=m
CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
CONFIG_NETFILTER_XT_TARGET_CONNMARK=m
CONFIG_NETFILTER_XT_TARGET_DSCP=m
+CONFIG_NETFILTER_XT_TARGET_HMARK=m
+CONFIG_NETFILTER_XT_TARGET_IDLETIMER=m
+CONFIG_NETFILTER_XT_TARGET_LOG=m
CONFIG_NETFILTER_XT_TARGET_MARK=m
CONFIG_NETFILTER_XT_TARGET_NFLOG=m
CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
+CONFIG_NETFILTER_XT_TARGET_NOTRACK=m
+CONFIG_NETFILTER_XT_TARGET_TEE=m
CONFIG_NETFILTER_XT_TARGET_TRACE=m
CONFIG_NETFILTER_XT_TARGET_TCPMSS=m
CONFIG_NETFILTER_XT_TARGET_TCPOPTSTRIP=m
+CONFIG_NETFILTER_XT_MATCH_ADDRTYPE=m
+CONFIG_NETFILTER_XT_MATCH_BPF=m
CONFIG_NETFILTER_XT_MATCH_CLUSTER=m
CONFIG_NETFILTER_XT_MATCH_COMMENT=m
CONFIG_NETFILTER_XT_MATCH_CONNBYTES=m
+CONFIG_NETFILTER_XT_MATCH_CONNLABEL=m
CONFIG_NETFILTER_XT_MATCH_CONNLIMIT=m
CONFIG_NETFILTER_XT_MATCH_CONNMARK=m
CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
+CONFIG_NETFILTER_XT_MATCH_DEVGROUP=m
CONFIG_NETFILTER_XT_MATCH_DSCP=m
CONFIG_NETFILTER_XT_MATCH_ESP=m
CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m
CONFIG_NETFILTER_XT_MATCH_MAC=m
CONFIG_NETFILTER_XT_MATCH_MARK=m
CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
+CONFIG_NETFILTER_XT_MATCH_NFACCT=m
+CONFIG_NETFILTER_XT_MATCH_OSF=m
CONFIG_NETFILTER_XT_MATCH_OWNER=m
CONFIG_NETFILTER_XT_MATCH_POLICY=m
CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m
CONFIG_NETFILTER_XT_MATCH_TCPMSS=m
CONFIG_NETFILTER_XT_MATCH_TIME=m
CONFIG_NETFILTER_XT_MATCH_U32=m
+CONFIG_IP_SET=m
+CONFIG_IP_SET_BITMAP_IP=m
+CONFIG_IP_SET_BITMAP_IPMAC=m
+CONFIG_IP_SET_BITMAP_PORT=m
+CONFIG_IP_SET_HASH_IP=m
+CONFIG_IP_SET_HASH_IPPORT=m
+CONFIG_IP_SET_HASH_IPPORTIP=m
+CONFIG_IP_SET_HASH_IPPORTNET=m
+CONFIG_IP_SET_HASH_NET=m
+CONFIG_IP_SET_HASH_NETPORT=m
+CONFIG_IP_SET_HASH_NETIFACE=m
+CONFIG_IP_SET_LIST_SET=m
CONFIG_NF_CONNTRACK_IPV4=m
-CONFIG_IP_NF_QUEUE=m
CONFIG_IP_NF_IPTABLES=m
-CONFIG_IP_NF_MATCH_ADDRTYPE=m
CONFIG_IP_NF_MATCH_AH=m
CONFIG_IP_NF_MATCH_ECN=m
+CONFIG_IP_NF_MATCH_RPFILTER=m
CONFIG_IP_NF_MATCH_TTL=m
CONFIG_IP_NF_FILTER=m
CONFIG_IP_NF_TARGET_REJECT=m
-CONFIG_IP_NF_TARGET_LOG=m
CONFIG_IP_NF_TARGET_ULOG=m
-CONFIG_NF_NAT=m
+CONFIG_NF_NAT_IPV4=m
CONFIG_IP_NF_TARGET_MASQUERADE=m
CONFIG_IP_NF_TARGET_NETMAP=m
CONFIG_IP_NF_TARGET_REDIRECT=m
-CONFIG_NF_NAT_SNMP_BASIC=m
CONFIG_IP_NF_MANGLE=m
CONFIG_IP_NF_TARGET_CLUSTERIP=m
CONFIG_IP_NF_TARGET_ECN=m
CONFIG_IP_NF_ARPFILTER=m
CONFIG_IP_NF_ARP_MANGLE=m
CONFIG_NF_CONNTRACK_IPV6=m
-CONFIG_IP6_NF_QUEUE=m
CONFIG_IP6_NF_IPTABLES=m
CONFIG_IP6_NF_MATCH_AH=m
CONFIG_IP6_NF_MATCH_EUI64=m
CONFIG_IP6_NF_MATCH_HL=m
CONFIG_IP6_NF_MATCH_IPV6HEADER=m
CONFIG_IP6_NF_MATCH_MH=m
+CONFIG_IP6_NF_MATCH_RPFILTER=m
CONFIG_IP6_NF_MATCH_RT=m
CONFIG_IP6_NF_TARGET_HL=m
-CONFIG_IP6_NF_TARGET_LOG=m
CONFIG_IP6_NF_FILTER=m
CONFIG_IP6_NF_TARGET_REJECT=m
CONFIG_IP6_NF_MANGLE=m
CONFIG_IP6_NF_RAW=m
+CONFIG_NF_NAT_IPV6=m
+CONFIG_IP6_NF_TARGET_MASQUERADE=m
+CONFIG_IP6_NF_TARGET_NPT=m
CONFIG_IP_DCCP=m
# CONFIG_IP_DCCP_CCID3 is not set
+CONFIG_SCTP_COOKIE_HMAC_SHA1=y
+CONFIG_RDS=m
+CONFIG_RDS_TCP=m
+CONFIG_L2TP=m
CONFIG_ATALK=m
+CONFIG_BATMAN_ADV=m
+CONFIG_BATMAN_ADV_DAT=y
+# CONFIG_WIRELESS is not set
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
# CONFIG_FIRMWARE_IN_KERNEL is not set
+# CONFIG_FW_LOADER_USER_HELPER is not set
CONFIG_CONNECTOR=m
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_CRYPTOLOOP=m
+CONFIG_BLK_DEV_DRBD=m
CONFIG_BLK_DEV_NBD=m
CONFIG_BLK_DEV_RAM=y
CONFIG_CDROM_PKTCDVD=m
CONFIG_BLK_DEV_SR_VENDOR=y
CONFIG_CHR_DEV_SG=m
CONFIG_SCSI_CONSTANTS=y
-CONFIG_SCSI_SAS_LIBSAS=m
-# CONFIG_SCSI_SAS_LIBSAS_DEBUG is not set
-CONFIG_SCSI_SRP_ATTRS=m
-CONFIG_SCSI_SRP_TGT_ATTRS=y
+CONFIG_SCSI_SAS_ATTRS=m
CONFIG_ISCSI_TCP=m
+CONFIG_ISCSI_BOOT_SYSFS=m
CONFIG_MD=y
-CONFIG_BLK_DEV_MD=m
CONFIG_MD_LINEAR=m
CONFIG_MD_RAID0=m
-CONFIG_MD_RAID1=m
-CONFIG_MD_RAID456=m
CONFIG_BLK_DEV_DM=m
CONFIG_DM_CRYPT=m
CONFIG_DM_SNAPSHOT=m
+CONFIG_DM_THIN_PROVISIONING=m
+CONFIG_DM_CACHE=m
CONFIG_DM_MIRROR=m
+CONFIG_DM_RAID=m
CONFIG_DM_ZERO=m
CONFIG_DM_MULTIPATH=m
CONFIG_DM_UEVENT=y
+CONFIG_TARGET_CORE=m
+CONFIG_TCM_IBLOCK=m
+CONFIG_TCM_FILEIO=m
+CONFIG_TCM_PSCSI=m
CONFIG_NETDEVICES=y
CONFIG_DUMMY=m
-CONFIG_MACVLAN=m
CONFIG_EQUALIZER=m
+CONFIG_NET_TEAM=m
+CONFIG_NET_TEAM_MODE_BROADCAST=m
+CONFIG_NET_TEAM_MODE_ROUNDROBIN=m
+CONFIG_NET_TEAM_MODE_ACTIVEBACKUP=m
+CONFIG_NET_TEAM_MODE_LOADBALANCE=m
+CONFIG_VXLAN=m
+CONFIG_NETCONSOLE=m
+CONFIG_NETCONSOLE_DYNAMIC=y
CONFIG_VETH=m
-CONFIG_NET_ETHERNET=y
CONFIG_HPLANCE=y
-# CONFIG_NETDEV_1000 is not set
-# CONFIG_NETDEV_10000 is not set
+# CONFIG_NET_CADENCE is not set
+# CONFIG_NET_VENDOR_BROADCOM is not set
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_WIZNET is not set
CONFIG_PPP=m
-CONFIG_PPP_FILTER=y
-CONFIG_PPP_ASYNC=m
-CONFIG_PPP_SYNC_TTY=m
-CONFIG_PPP_DEFLATE=m
CONFIG_PPP_BSDCOMP=m
+CONFIG_PPP_DEFLATE=m
+CONFIG_PPP_FILTER=y
CONFIG_PPP_MPPE=m
CONFIG_PPPOE=m
+CONFIG_PPTP=m
+CONFIG_PPPOL2TP=m
+CONFIG_PPP_ASYNC=m
+CONFIG_PPP_SYNC_TTY=m
CONFIG_SLIP=m
CONFIG_SLIP_COMPRESSED=y
CONFIG_SLIP_SMART=y
CONFIG_SLIP_MODE_SLIP6=y
-CONFIG_NETCONSOLE=m
-CONFIG_NETCONSOLE_DYNAMIC=y
-CONFIG_INPUT_FF_MEMLESS=m
+# CONFIG_WLAN is not set
+CONFIG_INPUT_EVDEV=m
# CONFIG_KEYBOARD_ATKBD is not set
-CONFIG_MOUSE_PS2=m
+# CONFIG_MOUSE_PS2 is not set
CONFIG_MOUSE_SERIAL=m
CONFIG_INPUT_MISC=y
CONFIG_HP_SDC_RTC=m
-# CONFIG_SERIO_SERPORT is not set
+CONFIG_SERIO_SERPORT=m
CONFIG_VT_HW_CONSOLE_BINDING=y
+# CONFIG_LEGACY_PTYS is not set
# CONFIG_DEVKMEM is not set
# CONFIG_HW_RANDOM is not set
-CONFIG_GEN_RTC=m
-CONFIG_GEN_RTC_X=y
+CONFIG_NTP_PPS=y
+CONFIG_PPS_CLIENT_LDISC=m
+CONFIG_PTP_1588_CLOCK=m
# CONFIG_HWMON is not set
CONFIG_FB=y
CONFIG_FRAMEBUFFER_CONSOLE=y
# CONFIG_LOGO_LINUX_VGA16 is not set
CONFIG_HID=m
CONFIG_HIDRAW=y
+CONFIG_UHID=m
+# CONFIG_HID_GENERIC is not set
# CONFIG_USB_SUPPORT is not set
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_GENERIC=m
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_PROC_HARDWARE=y
CONFIG_EXT2_FS=y
CONFIG_EXT3_FS=y
# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
# CONFIG_EXT3_FS_XATTR is not set
+CONFIG_EXT4_FS=y
CONFIG_REISERFS_FS=m
CONFIG_JFS_FS=m
CONFIG_XFS_FS=m
CONFIG_OCFS2_FS=m
-# CONFIG_OCFS2_FS_STATS is not set
# CONFIG_OCFS2_DEBUG_MASKLOG is not set
+CONFIG_FANOTIFY=y
CONFIG_QUOTA_NETLINK_INTERFACE=y
# CONFIG_PRINT_QUOTA_WARNING is not set
-CONFIG_AUTOFS_FS=m
CONFIG_AUTOFS4_FS=m
CONFIG_FUSE_FS=m
+CONFIG_CUSE=m
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
CONFIG_UDF_FS=m
-CONFIG_MSDOS_FS=y
+CONFIG_MSDOS_FS=m
CONFIG_VFAT_FS=m
CONFIG_PROC_KCORE=y
CONFIG_TMPFS=y
CONFIG_AFFS_FS=m
+CONFIG_ECRYPT_FS=m
+CONFIG_ECRYPT_FS_MESSAGING=y
CONFIG_HFS_FS=m
CONFIG_HFSPLUS_FS=m
CONFIG_CRAMFS=m
CONFIG_SQUASHFS=m
-CONFIG_MINIX_FS=y
+CONFIG_SQUASHFS_LZO=y
+CONFIG_MINIX_FS=m
+CONFIG_OMFS_FS=m
CONFIG_HPFS_FS=m
+CONFIG_QNX4FS_FS=m
+CONFIG_QNX6FS_FS=m
CONFIG_SYSV_FS=m
CONFIG_UFS_FS=m
CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
CONFIG_NFS_V4=y
+CONFIG_NFS_SWAP=y
CONFIG_ROOT_NFS=y
CONFIG_NFSD=m
CONFIG_NFSD_V3=y
-CONFIG_SMB_FS=m
-CONFIG_SMB_NLS_DEFAULT=y
+CONFIG_CIFS=m
+# CONFIG_CIFS_DEBUG is not set
CONFIG_CODA_FS=m
CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_CODEPAGE_737=m
CONFIG_NLS_ISO8859_15=m
CONFIG_NLS_KOI8_R=m
CONFIG_NLS_KOI8_U=m
+CONFIG_NLS_MAC_ROMAN=m
+CONFIG_NLS_MAC_CELTIC=m
+CONFIG_NLS_MAC_CENTEURO=m
+CONFIG_NLS_MAC_CROATIAN=m
+CONFIG_NLS_MAC_CYRILLIC=m
+CONFIG_NLS_MAC_GAELIC=m
+CONFIG_NLS_MAC_GREEK=m
+CONFIG_NLS_MAC_ICELAND=m
+CONFIG_NLS_MAC_INUIT=m
+CONFIG_NLS_MAC_ROMANIAN=m
+CONFIG_NLS_MAC_TURKISH=m
CONFIG_DLM=m
CONFIG_MAGIC_SYSRQ=y
-# CONFIG_RCU_CPU_STALL_DETECTOR is not set
-CONFIG_SYSCTL_SYSCALL_CHECK=y
+CONFIG_ASYNC_RAID6_TEST=m
+CONFIG_ENCRYPTED_KEYS=m
+CONFIG_CRYPTO_MANAGER=y
+CONFIG_CRYPTO_USER=m
CONFIG_CRYPTO_NULL=m
CONFIG_CRYPTO_CRYPTD=m
CONFIG_CRYPTO_TEST=m
CONFIG_CRYPTO_LRW=m
CONFIG_CRYPTO_PCBC=m
CONFIG_CRYPTO_XTS=m
-CONFIG_CRYPTO_HMAC=y
CONFIG_CRYPTO_XCBC=m
-CONFIG_CRYPTO_MD4=m
+CONFIG_CRYPTO_VMAC=m
CONFIG_CRYPTO_MICHAEL_MIC=m
CONFIG_CRYPTO_RMD128=m
CONFIG_CRYPTO_RMD160=m
CONFIG_CRYPTO_RMD256=m
CONFIG_CRYPTO_RMD320=m
-CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
CONFIG_CRYPTO_TGR192=m
CONFIG_CRYPTO_WP512=m
-CONFIG_CRYPTO_AES=m
CONFIG_CRYPTO_ANUBIS=m
CONFIG_CRYPTO_BLOWFISH=m
CONFIG_CRYPTO_CAMELLIA=m
CONFIG_CRYPTO_ZLIB=m
CONFIG_CRYPTO_LZO=m
# CONFIG_CRYPTO_ANSI_CPRNG is not set
+CONFIG_CRYPTO_USER_API_HASH=m
+CONFIG_CRYPTO_USER_API_SKCIPHER=m
# CONFIG_CRYPTO_HW is not set
-CONFIG_CRC16=m
CONFIG_CRC_T10DIF=y
+CONFIG_XZ_DEC_X86=y
+CONFIG_XZ_DEC_POWERPC=y
+CONFIG_XZ_DEC_IA64=y
+CONFIG_XZ_DEC_ARM=y
+CONFIG_XZ_DEC_ARMTHUMB=y
+CONFIG_XZ_DEC_SPARC=y
+CONFIG_XZ_DEC_TEST=m
-CONFIG_EXPERIMENTAL=y
CONFIG_LOCALVERSION="-mac"
CONFIG_SYSVIPC=y
CONFIG_POSIX_MQUEUE=y
+CONFIG_FHANDLE=y
CONFIG_BSD_PROCESS_ACCT=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_RELAY=y
+CONFIG_BSD_PROCESS_ACCT_V3=y
+CONFIG_LOG_BUF_SHIFT=16
+# CONFIG_UTS_NS is not set
+# CONFIG_IPC_NS is not set
+# CONFIG_PID_NS is not set
+# CONFIG_NET_NS is not set
CONFIG_BLK_DEV_INITRD=y
-# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_SLAB=y
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
-CONFIG_MAC=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_AMIGA_PARTITION=y
+CONFIG_ATARI_PARTITION=y
+CONFIG_BSD_DISKLABEL=y
+CONFIG_MINIX_SUBPARTITION=y
+CONFIG_SOLARIS_X86_PARTITION=y
+CONFIG_UNIXWARE_DISKLABEL=y
+CONFIG_SUN_PARTITION=y
+# CONFIG_EFI_PARTITION is not set
+CONFIG_SYSV68_PARTITION=y
+CONFIG_IOSCHED_DEADLINE=m
CONFIG_M68020=y
CONFIG_M68030=y
CONFIG_M68040=y
+CONFIG_M68KFPU_EMU=y
+CONFIG_MAC=y
+# CONFIG_COMPACTION is not set
+CONFIG_CLEANCACHE=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
CONFIG_BINFMT_AOUT=m
CONFIG_BINFMT_MISC=m
-CONFIG_PROC_HARDWARE=y
CONFIG_NET=y
CONFIG_PACKET=y
+CONFIG_PACKET_DIAG=m
CONFIG_UNIX=y
+CONFIG_UNIX_DIAG=m
+CONFIG_XFRM_MIGRATE=y
CONFIG_NET_KEY=y
-CONFIG_NET_KEY_MIGRATE=y
CONFIG_INET=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_IP_PNP_RARP=y
CONFIG_NET_IPIP=m
+CONFIG_NET_IPGRE_DEMUX=m
CONFIG_NET_IPGRE=m
CONFIG_SYN_COOKIES=y
+CONFIG_NET_IPVTI=m
CONFIG_INET_AH=m
CONFIG_INET_ESP=m
CONFIG_INET_IPCOMP=m
CONFIG_INET_XFRM_MODE_TRANSPORT=m
CONFIG_INET_XFRM_MODE_TUNNEL=m
CONFIG_INET_XFRM_MODE_BEET=m
+# CONFIG_INET_LRO is not set
CONFIG_INET_DIAG=m
+CONFIG_INET_UDP_DIAG=m
CONFIG_IPV6_PRIVACY=y
CONFIG_IPV6_ROUTER_PREF=y
-CONFIG_IPV6_ROUTE_INFO=y
CONFIG_INET6_AH=m
CONFIG_INET6_ESP=m
CONFIG_INET6_IPCOMP=m
-CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION=m
-CONFIG_IPV6_TUNNEL=m
+CONFIG_IPV6_GRE=m
CONFIG_NETFILTER=y
-CONFIG_NETFILTER_NETLINK_QUEUE=m
CONFIG_NF_CONNTRACK=m
+CONFIG_NF_CONNTRACK_ZONES=y
+# CONFIG_NF_CONNTRACK_PROCFS is not set
# CONFIG_NF_CT_PROTO_DCCP is not set
CONFIG_NF_CT_PROTO_UDPLITE=m
CONFIG_NF_CONNTRACK_AMANDA=m
CONFIG_NF_CONNTRACK_H323=m
CONFIG_NF_CONNTRACK_IRC=m
CONFIG_NF_CONNTRACK_NETBIOS_NS=m
+CONFIG_NF_CONNTRACK_SNMP=m
CONFIG_NF_CONNTRACK_PPTP=m
CONFIG_NF_CONNTRACK_SANE=m
CONFIG_NF_CONNTRACK_SIP=m
CONFIG_NF_CONNTRACK_TFTP=m
+CONFIG_NETFILTER_XT_SET=m
+CONFIG_NETFILTER_XT_TARGET_CHECKSUM=m
CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
CONFIG_NETFILTER_XT_TARGET_CONNMARK=m
CONFIG_NETFILTER_XT_TARGET_DSCP=m
+CONFIG_NETFILTER_XT_TARGET_HMARK=m
+CONFIG_NETFILTER_XT_TARGET_IDLETIMER=m
+CONFIG_NETFILTER_XT_TARGET_LOG=m
CONFIG_NETFILTER_XT_TARGET_MARK=m
CONFIG_NETFILTER_XT_TARGET_NFLOG=m
CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
+CONFIG_NETFILTER_XT_TARGET_NOTRACK=m
+CONFIG_NETFILTER_XT_TARGET_TEE=m
CONFIG_NETFILTER_XT_TARGET_TRACE=m
CONFIG_NETFILTER_XT_TARGET_TCPMSS=m
CONFIG_NETFILTER_XT_TARGET_TCPOPTSTRIP=m
+CONFIG_NETFILTER_XT_MATCH_ADDRTYPE=m
+CONFIG_NETFILTER_XT_MATCH_BPF=m
CONFIG_NETFILTER_XT_MATCH_CLUSTER=m
CONFIG_NETFILTER_XT_MATCH_COMMENT=m
CONFIG_NETFILTER_XT_MATCH_CONNBYTES=m
+CONFIG_NETFILTER_XT_MATCH_CONNLABEL=m
CONFIG_NETFILTER_XT_MATCH_CONNLIMIT=m
CONFIG_NETFILTER_XT_MATCH_CONNMARK=m
CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
+CONFIG_NETFILTER_XT_MATCH_DEVGROUP=m
CONFIG_NETFILTER_XT_MATCH_DSCP=m
CONFIG_NETFILTER_XT_MATCH_ESP=m
CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m
CONFIG_NETFILTER_XT_MATCH_MAC=m
CONFIG_NETFILTER_XT_MATCH_MARK=m
CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
+CONFIG_NETFILTER_XT_MATCH_NFACCT=m
+CONFIG_NETFILTER_XT_MATCH_OSF=m
CONFIG_NETFILTER_XT_MATCH_OWNER=m
CONFIG_NETFILTER_XT_MATCH_POLICY=m
CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m
CONFIG_NETFILTER_XT_MATCH_TCPMSS=m
CONFIG_NETFILTER_XT_MATCH_TIME=m
CONFIG_NETFILTER_XT_MATCH_U32=m
+CONFIG_IP_SET=m
+CONFIG_IP_SET_BITMAP_IP=m
+CONFIG_IP_SET_BITMAP_IPMAC=m
+CONFIG_IP_SET_BITMAP_PORT=m
+CONFIG_IP_SET_HASH_IP=m
+CONFIG_IP_SET_HASH_IPPORT=m
+CONFIG_IP_SET_HASH_IPPORTIP=m
+CONFIG_IP_SET_HASH_IPPORTNET=m
+CONFIG_IP_SET_HASH_NET=m
+CONFIG_IP_SET_HASH_NETPORT=m
+CONFIG_IP_SET_HASH_NETIFACE=m
+CONFIG_IP_SET_LIST_SET=m
CONFIG_NF_CONNTRACK_IPV4=m
-CONFIG_IP_NF_QUEUE=m
CONFIG_IP_NF_IPTABLES=m
-CONFIG_IP_NF_MATCH_ADDRTYPE=m
CONFIG_IP_NF_MATCH_AH=m
CONFIG_IP_NF_MATCH_ECN=m
+CONFIG_IP_NF_MATCH_RPFILTER=m
CONFIG_IP_NF_MATCH_TTL=m
CONFIG_IP_NF_FILTER=m
CONFIG_IP_NF_TARGET_REJECT=m
-CONFIG_IP_NF_TARGET_LOG=m
CONFIG_IP_NF_TARGET_ULOG=m
-CONFIG_NF_NAT=m
+CONFIG_NF_NAT_IPV4=m
CONFIG_IP_NF_TARGET_MASQUERADE=m
CONFIG_IP_NF_TARGET_NETMAP=m
CONFIG_IP_NF_TARGET_REDIRECT=m
-CONFIG_NF_NAT_SNMP_BASIC=m
CONFIG_IP_NF_MANGLE=m
CONFIG_IP_NF_TARGET_CLUSTERIP=m
CONFIG_IP_NF_TARGET_ECN=m
CONFIG_IP_NF_ARPFILTER=m
CONFIG_IP_NF_ARP_MANGLE=m
CONFIG_NF_CONNTRACK_IPV6=m
-CONFIG_IP6_NF_QUEUE=m
CONFIG_IP6_NF_IPTABLES=m
CONFIG_IP6_NF_MATCH_AH=m
CONFIG_IP6_NF_MATCH_EUI64=m
CONFIG_IP6_NF_MATCH_HL=m
CONFIG_IP6_NF_MATCH_IPV6HEADER=m
CONFIG_IP6_NF_MATCH_MH=m
+CONFIG_IP6_NF_MATCH_RPFILTER=m
CONFIG_IP6_NF_MATCH_RT=m
CONFIG_IP6_NF_TARGET_HL=m
-CONFIG_IP6_NF_TARGET_LOG=m
CONFIG_IP6_NF_FILTER=m
CONFIG_IP6_NF_TARGET_REJECT=m
CONFIG_IP6_NF_MANGLE=m
CONFIG_IP6_NF_RAW=m
+CONFIG_NF_NAT_IPV6=m
+CONFIG_IP6_NF_TARGET_MASQUERADE=m
+CONFIG_IP6_NF_TARGET_NPT=m
CONFIG_IP_DCCP=m
# CONFIG_IP_DCCP_CCID3 is not set
+CONFIG_SCTP_COOKIE_HMAC_SHA1=y
+CONFIG_RDS=m
+CONFIG_RDS_TCP=m
+CONFIG_L2TP=m
CONFIG_ATALK=m
CONFIG_DEV_APPLETALK=m
CONFIG_IPDDP=m
CONFIG_IPDDP_ENCAP=y
CONFIG_IPDDP_DECAP=y
+CONFIG_BATMAN_ADV=m
+CONFIG_BATMAN_ADV_DAT=y
+# CONFIG_WIRELESS is not set
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
# CONFIG_FIRMWARE_IN_KERNEL is not set
+# CONFIG_FW_LOADER_USER_HELPER is not set
CONFIG_CONNECTOR=m
-CONFIG_BLK_DEV_SWIM=y
+CONFIG_BLK_DEV_SWIM=m
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_CRYPTOLOOP=m
+CONFIG_BLK_DEV_DRBD=m
CONFIG_BLK_DEV_NBD=m
CONFIG_BLK_DEV_RAM=y
CONFIG_CDROM_PKTCDVD=m
CONFIG_ATA_OVER_ETH=m
CONFIG_IDE=y
+CONFIG_IDE_GD_ATAPI=y
CONFIG_BLK_DEV_IDECD=y
CONFIG_BLK_DEV_MAC_IDE=y
CONFIG_RAID_ATTRS=m
CONFIG_BLK_DEV_SR_VENDOR=y
CONFIG_CHR_DEV_SG=m
CONFIG_SCSI_CONSTANTS=y
-CONFIG_SCSI_SAS_LIBSAS=m
-# CONFIG_SCSI_SAS_LIBSAS_DEBUG is not set
-CONFIG_SCSI_SRP_ATTRS=m
-CONFIG_SCSI_SRP_TGT_ATTRS=y
+CONFIG_SCSI_SAS_ATTRS=m
CONFIG_ISCSI_TCP=m
+CONFIG_ISCSI_BOOT_SYSFS=m
CONFIG_MAC_SCSI=y
CONFIG_SCSI_MAC_ESP=y
CONFIG_MD=y
-CONFIG_BLK_DEV_MD=m
CONFIG_MD_LINEAR=m
CONFIG_MD_RAID0=m
-CONFIG_MD_RAID1=m
-CONFIG_MD_RAID456=m
CONFIG_BLK_DEV_DM=m
CONFIG_DM_CRYPT=m
CONFIG_DM_SNAPSHOT=m
+CONFIG_DM_THIN_PROVISIONING=m
+CONFIG_DM_CACHE=m
CONFIG_DM_MIRROR=m
+CONFIG_DM_RAID=m
CONFIG_DM_ZERO=m
CONFIG_DM_MULTIPATH=m
CONFIG_DM_UEVENT=y
+CONFIG_TARGET_CORE=m
+CONFIG_TCM_IBLOCK=m
+CONFIG_TCM_FILEIO=m
+CONFIG_TCM_PSCSI=m
CONFIG_ADB=y
CONFIG_ADB_MACII=y
-CONFIG_ADB_MACIISI=y
CONFIG_ADB_IOP=y
CONFIG_ADB_PMU68K=y
CONFIG_ADB_CUDA=y
CONFIG_MAC_EMUMOUSEBTN=y
CONFIG_NETDEVICES=y
CONFIG_DUMMY=m
-CONFIG_MACVLAN=m
CONFIG_EQUALIZER=m
+CONFIG_NET_TEAM=m
+CONFIG_NET_TEAM_MODE_BROADCAST=m
+CONFIG_NET_TEAM_MODE_ROUNDROBIN=m
+CONFIG_NET_TEAM_MODE_ACTIVEBACKUP=m
+CONFIG_NET_TEAM_MODE_LOADBALANCE=m
+CONFIG_VXLAN=m
+CONFIG_NETCONSOLE=m
+CONFIG_NETCONSOLE_DYNAMIC=y
CONFIG_VETH=m
-CONFIG_NET_ETHERNET=y
-CONFIG_MAC8390=y
-CONFIG_MAC89x0=m
-CONFIG_MACSONIC=m
CONFIG_MACMACE=y
-# CONFIG_NETDEV_1000 is not set
-# CONFIG_NETDEV_10000 is not set
+# CONFIG_NET_CADENCE is not set
+# CONFIG_NET_VENDOR_BROADCOM is not set
+CONFIG_MAC89x0=y
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+CONFIG_MACSONIC=y
+CONFIG_MAC8390=y
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_SMSC is not set
+# CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_WIZNET is not set
CONFIG_PPP=m
-CONFIG_PPP_FILTER=y
-CONFIG_PPP_ASYNC=m
-CONFIG_PPP_SYNC_TTY=m
-CONFIG_PPP_DEFLATE=m
CONFIG_PPP_BSDCOMP=m
+CONFIG_PPP_DEFLATE=m
+CONFIG_PPP_FILTER=y
CONFIG_PPP_MPPE=m
CONFIG_PPPOE=m
+CONFIG_PPTP=m
+CONFIG_PPPOL2TP=m
+CONFIG_PPP_ASYNC=m
+CONFIG_PPP_SYNC_TTY=m
CONFIG_SLIP=m
CONFIG_SLIP_COMPRESSED=y
CONFIG_SLIP_SMART=y
CONFIG_SLIP_MODE_SLIP6=y
-CONFIG_NETCONSOLE=m
-CONFIG_NETCONSOLE_DYNAMIC=y
-CONFIG_INPUT_FF_MEMLESS=m
+# CONFIG_WLAN is not set
+CONFIG_INPUT_EVDEV=m
# CONFIG_KEYBOARD_ATKBD is not set
-CONFIG_MOUSE_PS2=m
+# CONFIG_MOUSE_PS2 is not set
CONFIG_MOUSE_SERIAL=m
CONFIG_INPUT_MISC=y
CONFIG_INPUT_M68K_BEEP=m
CONFIG_SERIO=m
-# CONFIG_SERIO_SERPORT is not set
CONFIG_VT_HW_CONSOLE_BINDING=y
+# CONFIG_LEGACY_PTYS is not set
# CONFIG_DEVKMEM is not set
CONFIG_SERIAL_PMACZILOG=y
CONFIG_SERIAL_PMACZILOG_TTYS=y
CONFIG_SERIAL_PMACZILOG_CONSOLE=y
# CONFIG_HW_RANDOM is not set
-CONFIG_GEN_RTC=m
-CONFIG_GEN_RTC_X=y
+CONFIG_NTP_PPS=y
+CONFIG_PPS_CLIENT_LDISC=m
+CONFIG_PTP_1588_CLOCK=m
# CONFIG_HWMON is not set
CONFIG_FB=y
CONFIG_FB_VALKYRIE=y
CONFIG_LOGO=y
CONFIG_HID=m
CONFIG_HIDRAW=y
+CONFIG_UHID=m
+# CONFIG_HID_GENERIC is not set
# CONFIG_USB_SUPPORT is not set
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_GENERIC=m
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_PROC_HARDWARE=y
CONFIG_EXT2_FS=y
CONFIG_EXT3_FS=y
# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
# CONFIG_EXT3_FS_XATTR is not set
+CONFIG_EXT4_FS=y
CONFIG_REISERFS_FS=m
CONFIG_JFS_FS=m
CONFIG_XFS_FS=m
CONFIG_OCFS2_FS=m
-# CONFIG_OCFS2_FS_STATS is not set
# CONFIG_OCFS2_DEBUG_MASKLOG is not set
+CONFIG_FANOTIFY=y
CONFIG_QUOTA_NETLINK_INTERFACE=y
# CONFIG_PRINT_QUOTA_WARNING is not set
-CONFIG_AUTOFS_FS=m
CONFIG_AUTOFS4_FS=m
CONFIG_FUSE_FS=m
+CONFIG_CUSE=m
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
CONFIG_UDF_FS=m
-CONFIG_MSDOS_FS=y
+CONFIG_MSDOS_FS=m
CONFIG_VFAT_FS=m
CONFIG_PROC_KCORE=y
CONFIG_TMPFS=y
CONFIG_AFFS_FS=m
-CONFIG_HFS_FS=y
-CONFIG_HFSPLUS_FS=y
+CONFIG_ECRYPT_FS=m
+CONFIG_ECRYPT_FS_MESSAGING=y
+CONFIG_HFS_FS=m
+CONFIG_HFSPLUS_FS=m
CONFIG_CRAMFS=m
CONFIG_SQUASHFS=m
-CONFIG_MINIX_FS=y
+CONFIG_SQUASHFS_LZO=y
+CONFIG_MINIX_FS=m
+CONFIG_OMFS_FS=m
CONFIG_HPFS_FS=m
+CONFIG_QNX4FS_FS=m
+CONFIG_QNX6FS_FS=m
CONFIG_SYSV_FS=m
CONFIG_UFS_FS=m
-CONFIG_NFS_FS=m
-CONFIG_NFS_V3=y
+CONFIG_NFS_FS=y
CONFIG_NFS_V4=y
+CONFIG_NFS_SWAP=y
+CONFIG_ROOT_NFS=y
CONFIG_NFSD=m
CONFIG_NFSD_V3=y
-CONFIG_SMB_FS=m
-CONFIG_SMB_NLS_DEFAULT=y
+CONFIG_CIFS=m
+# CONFIG_CIFS_DEBUG is not set
CONFIG_CODA_FS=m
CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_CODEPAGE_737=m
CONFIG_NLS_ISO8859_15=m
CONFIG_NLS_KOI8_R=m
CONFIG_NLS_KOI8_U=m
+CONFIG_NLS_MAC_ROMAN=m
+CONFIG_NLS_MAC_CELTIC=m
+CONFIG_NLS_MAC_CENTEURO=m
+CONFIG_NLS_MAC_CROATIAN=m
+CONFIG_NLS_MAC_CYRILLIC=m
+CONFIG_NLS_MAC_GAELIC=m
+CONFIG_NLS_MAC_GREEK=m
+CONFIG_NLS_MAC_ICELAND=m
+CONFIG_NLS_MAC_INUIT=m
+CONFIG_NLS_MAC_ROMANIAN=m
+CONFIG_NLS_MAC_TURKISH=m
CONFIG_DLM=m
CONFIG_MAGIC_SYSRQ=y
-# CONFIG_RCU_CPU_STALL_DETECTOR is not set
-CONFIG_SYSCTL_SYSCALL_CHECK=y
+CONFIG_ASYNC_RAID6_TEST=m
+CONFIG_ENCRYPTED_KEYS=m
+CONFIG_CRYPTO_MANAGER=y
+CONFIG_CRYPTO_USER=m
CONFIG_CRYPTO_NULL=m
CONFIG_CRYPTO_CRYPTD=m
CONFIG_CRYPTO_TEST=m
CONFIG_CRYPTO_LRW=m
CONFIG_CRYPTO_PCBC=m
CONFIG_CRYPTO_XTS=m
-CONFIG_CRYPTO_HMAC=y
CONFIG_CRYPTO_XCBC=m
-CONFIG_CRYPTO_MD4=m
+CONFIG_CRYPTO_VMAC=m
CONFIG_CRYPTO_MICHAEL_MIC=m
CONFIG_CRYPTO_RMD128=m
CONFIG_CRYPTO_RMD160=m
CONFIG_CRYPTO_RMD256=m
CONFIG_CRYPTO_RMD320=m
-CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
CONFIG_CRYPTO_TGR192=m
CONFIG_CRYPTO_WP512=m
-CONFIG_CRYPTO_AES=m
CONFIG_CRYPTO_ANUBIS=m
CONFIG_CRYPTO_BLOWFISH=m
CONFIG_CRYPTO_CAMELLIA=m
CONFIG_CRYPTO_ZLIB=m
CONFIG_CRYPTO_LZO=m
# CONFIG_CRYPTO_ANSI_CPRNG is not set
+CONFIG_CRYPTO_USER_API_HASH=m
+CONFIG_CRYPTO_USER_API_SKCIPHER=m
# CONFIG_CRYPTO_HW is not set
-CONFIG_CRC16=m
CONFIG_CRC_T10DIF=y
+CONFIG_XZ_DEC_X86=y
+CONFIG_XZ_DEC_POWERPC=y
+CONFIG_XZ_DEC_IA64=y
+CONFIG_XZ_DEC_ARM=y
+CONFIG_XZ_DEC_ARMTHUMB=y
+CONFIG_XZ_DEC_SPARC=y
+CONFIG_XZ_DEC_TEST=m
-CONFIG_EXPERIMENTAL=y
CONFIG_LOCALVERSION="-multi"
CONFIG_SYSVIPC=y
CONFIG_POSIX_MQUEUE=y
+CONFIG_FHANDLE=y
CONFIG_BSD_PROCESS_ACCT=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_RELAY=y
+CONFIG_BSD_PROCESS_ACCT_V3=y
+CONFIG_LOG_BUF_SHIFT=16
+# CONFIG_UTS_NS is not set
+# CONFIG_IPC_NS is not set
+# CONFIG_PID_NS is not set
+# CONFIG_NET_NS is not set
CONFIG_BLK_DEV_INITRD=y
-# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_SLAB=y
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_BSD_DISKLABEL=y
+CONFIG_MINIX_SUBPARTITION=y
+CONFIG_SOLARIS_X86_PARTITION=y
+CONFIG_UNIXWARE_DISKLABEL=y
+# CONFIG_EFI_PARTITION is not set
+CONFIG_IOSCHED_DEADLINE=m
+CONFIG_M68020=y
+CONFIG_M68040=y
+CONFIG_M68060=y
+CONFIG_M68KFPU_EMU=y
CONFIG_AMIGA=y
CONFIG_ATARI=y
CONFIG_MAC=y
CONFIG_HP300=y
CONFIG_SUN3X=y
CONFIG_Q40=y
-CONFIG_M68020=y
-CONFIG_M68040=y
-CONFIG_M68060=y
-CONFIG_BINFMT_AOUT=m
-CONFIG_BINFMT_MISC=m
CONFIG_ZORRO=y
CONFIG_AMIGA_PCMCIA=y
-CONFIG_STRAM_PROC=y
-CONFIG_HEARTBEAT=y
-CONFIG_PROC_HARDWARE=y
CONFIG_ZORRO_NAMES=y
+# CONFIG_COMPACTION is not set
+CONFIG_CLEANCACHE=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_BINFMT_AOUT=m
+CONFIG_BINFMT_MISC=m
CONFIG_NET=y
CONFIG_PACKET=y
+CONFIG_PACKET_DIAG=m
CONFIG_UNIX=y
+CONFIG_UNIX_DIAG=m
+CONFIG_XFRM_MIGRATE=y
CONFIG_NET_KEY=y
-CONFIG_NET_KEY_MIGRATE=y
CONFIG_INET=y
CONFIG_IP_PNP=y
CONFIG_IP_PNP_DHCP=y
CONFIG_IP_PNP_BOOTP=y
CONFIG_IP_PNP_RARP=y
CONFIG_NET_IPIP=m
+CONFIG_NET_IPGRE_DEMUX=m
CONFIG_NET_IPGRE=m
CONFIG_SYN_COOKIES=y
+CONFIG_NET_IPVTI=m
CONFIG_INET_AH=m
CONFIG_INET_ESP=m
CONFIG_INET_IPCOMP=m
CONFIG_INET_XFRM_MODE_TRANSPORT=m
CONFIG_INET_XFRM_MODE_TUNNEL=m
CONFIG_INET_XFRM_MODE_BEET=m
+# CONFIG_INET_LRO is not set
CONFIG_INET_DIAG=m
+CONFIG_INET_UDP_DIAG=m
CONFIG_IPV6_PRIVACY=y
CONFIG_IPV6_ROUTER_PREF=y
-CONFIG_IPV6_ROUTE_INFO=y
CONFIG_INET6_AH=m
CONFIG_INET6_ESP=m
CONFIG_INET6_IPCOMP=m
-CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION=m
-CONFIG_IPV6_TUNNEL=m
+CONFIG_IPV6_GRE=m
CONFIG_NETFILTER=y
-CONFIG_NETFILTER_NETLINK_QUEUE=m
CONFIG_NF_CONNTRACK=m
+CONFIG_NF_CONNTRACK_ZONES=y
+# CONFIG_NF_CONNTRACK_PROCFS is not set
# CONFIG_NF_CT_PROTO_DCCP is not set
CONFIG_NF_CT_PROTO_UDPLITE=m
CONFIG_NF_CONNTRACK_AMANDA=m
CONFIG_NF_CONNTRACK_H323=m
CONFIG_NF_CONNTRACK_IRC=m
CONFIG_NF_CONNTRACK_NETBIOS_NS=m
+CONFIG_NF_CONNTRACK_SNMP=m
CONFIG_NF_CONNTRACK_PPTP=m
CONFIG_NF_CONNTRACK_SANE=m
CONFIG_NF_CONNTRACK_SIP=m
CONFIG_NF_CONNTRACK_TFTP=m
+CONFIG_NETFILTER_XT_SET=m
+CONFIG_NETFILTER_XT_TARGET_CHECKSUM=m
CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
CONFIG_NETFILTER_XT_TARGET_CONNMARK=m
CONFIG_NETFILTER_XT_TARGET_DSCP=m
+CONFIG_NETFILTER_XT_TARGET_HMARK=m
+CONFIG_NETFILTER_XT_TARGET_IDLETIMER=m
+CONFIG_NETFILTER_XT_TARGET_LOG=m
CONFIG_NETFILTER_XT_TARGET_MARK=m
CONFIG_NETFILTER_XT_TARGET_NFLOG=m
CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
+CONFIG_NETFILTER_XT_TARGET_NOTRACK=m
+CONFIG_NETFILTER_XT_TARGET_TEE=m
CONFIG_NETFILTER_XT_TARGET_TRACE=m
CONFIG_NETFILTER_XT_TARGET_TCPMSS=m
CONFIG_NETFILTER_XT_TARGET_TCPOPTSTRIP=m
+CONFIG_NETFILTER_XT_MATCH_ADDRTYPE=m
+CONFIG_NETFILTER_XT_MATCH_BPF=m
CONFIG_NETFILTER_XT_MATCH_CLUSTER=m
CONFIG_NETFILTER_XT_MATCH_COMMENT=m
CONFIG_NETFILTER_XT_MATCH_CONNBYTES=m
+CONFIG_NETFILTER_XT_MATCH_CONNLABEL=m
CONFIG_NETFILTER_XT_MATCH_CONNLIMIT=m
CONFIG_NETFILTER_XT_MATCH_CONNMARK=m
CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
+CONFIG_NETFILTER_XT_MATCH_DEVGROUP=m
CONFIG_NETFILTER_XT_MATCH_DSCP=m
CONFIG_NETFILTER_XT_MATCH_ESP=m
CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m
CONFIG_NETFILTER_XT_MATCH_MAC=m
CONFIG_NETFILTER_XT_MATCH_MARK=m
CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
+CONFIG_NETFILTER_XT_MATCH_NFACCT=m
+CONFIG_NETFILTER_XT_MATCH_OSF=m
CONFIG_NETFILTER_XT_MATCH_OWNER=m
CONFIG_NETFILTER_XT_MATCH_POLICY=m
CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m
CONFIG_NETFILTER_XT_MATCH_TCPMSS=m
CONFIG_NETFILTER_XT_MATCH_TIME=m
CONFIG_NETFILTER_XT_MATCH_U32=m
+CONFIG_IP_SET=m
+CONFIG_IP_SET_BITMAP_IP=m
+CONFIG_IP_SET_BITMAP_IPMAC=m
+CONFIG_IP_SET_BITMAP_PORT=m
+CONFIG_IP_SET_HASH_IP=m
+CONFIG_IP_SET_HASH_IPPORT=m
+CONFIG_IP_SET_HASH_IPPORTIP=m
+CONFIG_IP_SET_HASH_IPPORTNET=m
+CONFIG_IP_SET_HASH_NET=m
+CONFIG_IP_SET_HASH_NETPORT=m
+CONFIG_IP_SET_HASH_NETIFACE=m
+CONFIG_IP_SET_LIST_SET=m
CONFIG_NF_CONNTRACK_IPV4=m
-CONFIG_IP_NF_QUEUE=m
CONFIG_IP_NF_IPTABLES=m
-CONFIG_IP_NF_MATCH_ADDRTYPE=m
CONFIG_IP_NF_MATCH_AH=m
CONFIG_IP_NF_MATCH_ECN=m
+CONFIG_IP_NF_MATCH_RPFILTER=m
CONFIG_IP_NF_MATCH_TTL=m
CONFIG_IP_NF_FILTER=m
CONFIG_IP_NF_TARGET_REJECT=m
-CONFIG_IP_NF_TARGET_LOG=m
CONFIG_IP_NF_TARGET_ULOG=m
-CONFIG_NF_NAT=m
+CONFIG_NF_NAT_IPV4=m
CONFIG_IP_NF_TARGET_MASQUERADE=m
CONFIG_IP_NF_TARGET_NETMAP=m
CONFIG_IP_NF_TARGET_REDIRECT=m
-CONFIG_NF_NAT_SNMP_BASIC=m
CONFIG_IP_NF_MANGLE=m
CONFIG_IP_NF_TARGET_CLUSTERIP=m
CONFIG_IP_NF_TARGET_ECN=m
CONFIG_IP_NF_ARPFILTER=m
CONFIG_IP_NF_ARP_MANGLE=m
CONFIG_NF_CONNTRACK_IPV6=m
-CONFIG_IP6_NF_QUEUE=m
CONFIG_IP6_NF_IPTABLES=m
CONFIG_IP6_NF_MATCH_AH=m
CONFIG_IP6_NF_MATCH_EUI64=m
CONFIG_IP6_NF_MATCH_HL=m
CONFIG_IP6_NF_MATCH_IPV6HEADER=m
CONFIG_IP6_NF_MATCH_MH=m
+CONFIG_IP6_NF_MATCH_RPFILTER=m
CONFIG_IP6_NF_MATCH_RT=m
CONFIG_IP6_NF_TARGET_HL=m
-CONFIG_IP6_NF_TARGET_LOG=m
CONFIG_IP6_NF_FILTER=m
CONFIG_IP6_NF_TARGET_REJECT=m
CONFIG_IP6_NF_MANGLE=m
CONFIG_IP6_NF_RAW=m
+CONFIG_NF_NAT_IPV6=m
+CONFIG_IP6_NF_TARGET_MASQUERADE=m
+CONFIG_IP6_NF_TARGET_NPT=m
CONFIG_IP_DCCP=m
# CONFIG_IP_DCCP_CCID3 is not set
+CONFIG_SCTP_COOKIE_HMAC_SHA1=y
+CONFIG_RDS=m
+CONFIG_RDS_TCP=m
+CONFIG_L2TP=m
CONFIG_ATALK=m
CONFIG_DEV_APPLETALK=m
CONFIG_IPDDP=m
CONFIG_IPDDP_ENCAP=y
CONFIG_IPDDP_DECAP=y
+CONFIG_BATMAN_ADV=m
+CONFIG_BATMAN_ADV_DAT=y
+# CONFIG_WIRELESS is not set
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
# CONFIG_FIRMWARE_IN_KERNEL is not set
+# CONFIG_FW_LOADER_USER_HELPER is not set
CONFIG_CONNECTOR=m
CONFIG_PARPORT=m
CONFIG_PARPORT_AMIGA=m
CONFIG_PARPORT_1284=y
CONFIG_AMIGA_FLOPPY=y
CONFIG_ATARI_FLOPPY=y
-CONFIG_BLK_DEV_SWIM=y
+CONFIG_BLK_DEV_SWIM=m
CONFIG_AMIGA_Z2RAM=y
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_CRYPTOLOOP=m
+CONFIG_BLK_DEV_DRBD=m
CONFIG_BLK_DEV_NBD=m
CONFIG_BLK_DEV_RAM=y
CONFIG_CDROM_PKTCDVD=m
CONFIG_ATA_OVER_ETH=m
CONFIG_IDE=y
+CONFIG_IDE_GD_ATAPI=y
CONFIG_BLK_DEV_IDECD=y
CONFIG_BLK_DEV_GAYLE=y
CONFIG_BLK_DEV_BUDDHA=y
CONFIG_BLK_DEV_SR_VENDOR=y
CONFIG_CHR_DEV_SG=m
CONFIG_SCSI_CONSTANTS=y
-CONFIG_SCSI_SAS_LIBSAS=m
-# CONFIG_SCSI_SAS_LIBSAS_DEBUG is not set
-CONFIG_SCSI_SRP_ATTRS=m
-CONFIG_SCSI_SRP_TGT_ATTRS=y
+CONFIG_SCSI_SAS_ATTRS=m
CONFIG_ISCSI_TCP=m
+CONFIG_ISCSI_BOOT_SYSFS=m
CONFIG_A3000_SCSI=y
CONFIG_A2091_SCSI=y
CONFIG_GVP11_SCSI=y
CONFIG_BVME6000_SCSI=y
CONFIG_SUN3X_ESP=y
CONFIG_MD=y
-CONFIG_BLK_DEV_MD=m
CONFIG_MD_LINEAR=m
CONFIG_MD_RAID0=m
-CONFIG_MD_RAID1=m
-CONFIG_MD_RAID456=m
CONFIG_BLK_DEV_DM=m
CONFIG_DM_CRYPT=m
CONFIG_DM_SNAPSHOT=m
+CONFIG_DM_THIN_PROVISIONING=m
+CONFIG_DM_CACHE=m
CONFIG_DM_MIRROR=m
+CONFIG_DM_RAID=m
CONFIG_DM_ZERO=m
CONFIG_DM_MULTIPATH=m
CONFIG_DM_UEVENT=y
+CONFIG_TARGET_CORE=m
+CONFIG_TCM_IBLOCK=m
+CONFIG_TCM_FILEIO=m
+CONFIG_TCM_PSCSI=m
CONFIG_ADB=y
CONFIG_ADB_MACII=y
-CONFIG_ADB_MACIISI=y
CONFIG_ADB_IOP=y
CONFIG_ADB_PMU68K=y
CONFIG_ADB_CUDA=y
CONFIG_MAC_EMUMOUSEBTN=y
CONFIG_NETDEVICES=y
CONFIG_DUMMY=m
-CONFIG_MACVLAN=m
CONFIG_EQUALIZER=m
-CONFIG_VETH=m
-CONFIG_NET_ETHERNET=y
CONFIG_MII=y
-CONFIG_ARIADNE=y
+CONFIG_NET_TEAM=m
+CONFIG_NET_TEAM_MODE_BROADCAST=m
+CONFIG_NET_TEAM_MODE_ROUNDROBIN=m
+CONFIG_NET_TEAM_MODE_ACTIVEBACKUP=m
+CONFIG_NET_TEAM_MODE_LOADBALANCE=m
+CONFIG_VXLAN=m
+CONFIG_NETCONSOLE=m
+CONFIG_NETCONSOLE_DYNAMIC=y
+CONFIG_VETH=m
+# CONFIG_NET_VENDOR_3COM is not set
CONFIG_A2065=y
-CONFIG_HYDRA=y
-CONFIG_ZORRO8390=y
-CONFIG_APNE=y
-CONFIG_MAC8390=y
-CONFIG_MAC89x0=y
-CONFIG_MACSONIC=y
-CONFIG_MACMACE=y
-CONFIG_MVME147_NET=y
-CONFIG_MVME16x_NET=y
-CONFIG_BVME6000_NET=y
+CONFIG_ARIADNE=y
CONFIG_ATARILANCE=y
-CONFIG_SUN3LANCE=y
CONFIG_HPLANCE=y
+CONFIG_MVME147_NET=y
+CONFIG_SUN3LANCE=y
+CONFIG_MACMACE=y
+# CONFIG_NET_CADENCE is not set
+# CONFIG_NET_VENDOR_BROADCOM is not set
+CONFIG_MAC89x0=y
+# CONFIG_NET_VENDOR_FUJITSU is not set
+# CONFIG_NET_VENDOR_HP is not set
+CONFIG_BVME6000_NET=y
+CONFIG_MVME16x_NET=y
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+CONFIG_MACSONIC=y
+CONFIG_HYDRA=y
+CONFIG_MAC8390=y
CONFIG_NE2000=m
-# CONFIG_NETDEV_1000 is not set
-# CONFIG_NETDEV_10000 is not set
+CONFIG_APNE=y
+CONFIG_ZORRO8390=y
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_WIZNET is not set
CONFIG_PPP=m
-CONFIG_PPP_FILTER=y
-CONFIG_PPP_ASYNC=m
-CONFIG_PPP_SYNC_TTY=m
-CONFIG_PPP_DEFLATE=m
CONFIG_PPP_BSDCOMP=m
+CONFIG_PPP_DEFLATE=m
+CONFIG_PPP_FILTER=y
CONFIG_PPP_MPPE=m
CONFIG_PPPOE=m
+CONFIG_PPTP=m
+CONFIG_PPPOL2TP=m
+CONFIG_PPP_ASYNC=m
+CONFIG_PPP_SYNC_TTY=m
CONFIG_SLIP=m
CONFIG_SLIP_COMPRESSED=y
CONFIG_SLIP_SMART=y
CONFIG_SLIP_MODE_SLIP6=y
-CONFIG_NETCONSOLE=m
-CONFIG_NETCONSOLE_DYNAMIC=y
-CONFIG_INPUT_FF_MEMLESS=m
+# CONFIG_WLAN is not set
+CONFIG_INPUT_EVDEV=m
CONFIG_KEYBOARD_AMIGA=y
CONFIG_KEYBOARD_ATARI=y
# CONFIG_KEYBOARD_ATKBD is not set
CONFIG_KEYBOARD_SUNKBD=y
-CONFIG_MOUSE_PS2=m
+# CONFIG_MOUSE_PS2 is not set
CONFIG_MOUSE_SERIAL=m
CONFIG_MOUSE_AMIGA=m
CONFIG_MOUSE_ATARI=m
CONFIG_JOYSTICK_AMIGA=m
CONFIG_INPUT_MISC=y
CONFIG_INPUT_M68K_BEEP=m
-CONFIG_HP_SDC_RTC=y
-# CONFIG_SERIO_SERPORT is not set
+CONFIG_HP_SDC_RTC=m
CONFIG_SERIO_Q40KBD=y
CONFIG_VT_HW_CONSOLE_BINDING=y
+# CONFIG_LEGACY_PTYS is not set
# CONFIG_DEVKMEM is not set
CONFIG_SERIAL_PMACZILOG=y
CONFIG_SERIAL_PMACZILOG_TTYS=y
CONFIG_SERIAL_PMACZILOG_CONSOLE=y
CONFIG_PRINTER=m
# CONFIG_HW_RANDOM is not set
-CONFIG_GEN_RTC=y
-CONFIG_GEN_RTC_X=y
+CONFIG_NTP_PPS=y
+CONFIG_PPS_CLIENT_LDISC=m
+CONFIG_PPS_CLIENT_PARPORT=m
+CONFIG_PTP_1588_CLOCK=m
# CONFIG_HWMON is not set
CONFIG_FB=y
CONFIG_FB_CIRRUS=y
CONFIG_DMASOUND_Q40=m
CONFIG_HID=m
CONFIG_HIDRAW=y
+CONFIG_UHID=m
+# CONFIG_HID_GENERIC is not set
# CONFIG_USB_SUPPORT is not set
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_MSM6242=m
+CONFIG_RTC_DRV_RP5C01=m
+CONFIG_RTC_DRV_GENERIC=m
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_HEARTBEAT=y
+CONFIG_PROC_HARDWARE=y
+CONFIG_NATFEAT=y
+CONFIG_NFBLOCK=y
+CONFIG_NFCON=y
+CONFIG_NFETH=y
CONFIG_ATARI_DSP56K=m
CONFIG_AMIGA_BUILTIN_SERIAL=y
CONFIG_SERIAL_CONSOLE=y
CONFIG_EXT3_FS=y
# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
# CONFIG_EXT3_FS_XATTR is not set
+CONFIG_EXT4_FS=y
CONFIG_REISERFS_FS=m
CONFIG_JFS_FS=m
CONFIG_XFS_FS=m
CONFIG_OCFS2_FS=m
-# CONFIG_OCFS2_FS_STATS is not set
# CONFIG_OCFS2_DEBUG_MASKLOG is not set
+CONFIG_FANOTIFY=y
CONFIG_QUOTA_NETLINK_INTERFACE=y
# CONFIG_PRINT_QUOTA_WARNING is not set
-CONFIG_AUTOFS_FS=m
CONFIG_AUTOFS4_FS=m
CONFIG_FUSE_FS=m
+CONFIG_CUSE=m
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
CONFIG_UDF_FS=m
-CONFIG_MSDOS_FS=y
+CONFIG_MSDOS_FS=m
CONFIG_VFAT_FS=m
CONFIG_PROC_KCORE=y
CONFIG_TMPFS=y
CONFIG_AFFS_FS=m
-CONFIG_HFS_FS=y
-CONFIG_HFSPLUS_FS=y
+CONFIG_ECRYPT_FS=m
+CONFIG_ECRYPT_FS_MESSAGING=y
+CONFIG_HFS_FS=m
+CONFIG_HFSPLUS_FS=m
CONFIG_CRAMFS=m
CONFIG_SQUASHFS=m
-CONFIG_MINIX_FS=y
+CONFIG_SQUASHFS_LZO=y
+CONFIG_MINIX_FS=m
+CONFIG_OMFS_FS=m
CONFIG_HPFS_FS=m
+CONFIG_QNX4FS_FS=m
+CONFIG_QNX6FS_FS=m
CONFIG_SYSV_FS=m
CONFIG_UFS_FS=m
CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
CONFIG_NFS_V4=y
+CONFIG_NFS_SWAP=y
CONFIG_ROOT_NFS=y
CONFIG_NFSD=m
CONFIG_NFSD_V3=y
-CONFIG_SMB_FS=m
-CONFIG_SMB_NLS_DEFAULT=y
+CONFIG_CIFS=m
+# CONFIG_CIFS_DEBUG is not set
CONFIG_CODA_FS=m
CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_CODEPAGE_737=m
CONFIG_NLS_ISO8859_15=m
CONFIG_NLS_KOI8_R=m
CONFIG_NLS_KOI8_U=m
+CONFIG_NLS_MAC_ROMAN=m
+CONFIG_NLS_MAC_CELTIC=m
+CONFIG_NLS_MAC_CENTEURO=m
+CONFIG_NLS_MAC_CROATIAN=m
+CONFIG_NLS_MAC_CYRILLIC=m
+CONFIG_NLS_MAC_GAELIC=m
+CONFIG_NLS_MAC_GREEK=m
+CONFIG_NLS_MAC_ICELAND=m
+CONFIG_NLS_MAC_INUIT=m
+CONFIG_NLS_MAC_ROMANIAN=m
+CONFIG_NLS_MAC_TURKISH=m
CONFIG_DLM=m
CONFIG_MAGIC_SYSRQ=y
-# CONFIG_RCU_CPU_STALL_DETECTOR is not set
-CONFIG_SYSCTL_SYSCALL_CHECK=y
+CONFIG_ASYNC_RAID6_TEST=m
+CONFIG_ENCRYPTED_KEYS=m
+CONFIG_CRYPTO_MANAGER=y
+CONFIG_CRYPTO_USER=m
CONFIG_CRYPTO_NULL=m
CONFIG_CRYPTO_CRYPTD=m
CONFIG_CRYPTO_TEST=m
CONFIG_CRYPTO_LRW=m
CONFIG_CRYPTO_PCBC=m
CONFIG_CRYPTO_XTS=m
-CONFIG_CRYPTO_HMAC=y
CONFIG_CRYPTO_XCBC=m
-CONFIG_CRYPTO_MD4=m
+CONFIG_CRYPTO_VMAC=m
CONFIG_CRYPTO_MICHAEL_MIC=m
CONFIG_CRYPTO_RMD128=m
CONFIG_CRYPTO_RMD160=m
CONFIG_CRYPTO_RMD256=m
CONFIG_CRYPTO_RMD320=m
-CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
CONFIG_CRYPTO_TGR192=m
CONFIG_CRYPTO_WP512=m
-CONFIG_CRYPTO_AES=m
CONFIG_CRYPTO_ANUBIS=m
CONFIG_CRYPTO_BLOWFISH=m
CONFIG_CRYPTO_CAMELLIA=m
CONFIG_CRYPTO_ZLIB=m
CONFIG_CRYPTO_LZO=m
# CONFIG_CRYPTO_ANSI_CPRNG is not set
+CONFIG_CRYPTO_USER_API_HASH=m
+CONFIG_CRYPTO_USER_API_SKCIPHER=m
# CONFIG_CRYPTO_HW is not set
-CONFIG_CRC16=y
CONFIG_CRC_T10DIF=y
+CONFIG_XZ_DEC_X86=y
+CONFIG_XZ_DEC_POWERPC=y
+CONFIG_XZ_DEC_IA64=y
+CONFIG_XZ_DEC_ARM=y
+CONFIG_XZ_DEC_ARMTHUMB=y
+CONFIG_XZ_DEC_SPARC=y
+CONFIG_XZ_DEC_TEST=m
-CONFIG_EXPERIMENTAL=y
CONFIG_LOCALVERSION="-mvme147"
CONFIG_SYSVIPC=y
CONFIG_POSIX_MQUEUE=y
+CONFIG_FHANDLE=y
CONFIG_BSD_PROCESS_ACCT=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_RELAY=y
+CONFIG_BSD_PROCESS_ACCT_V3=y
+CONFIG_LOG_BUF_SHIFT=16
+# CONFIG_UTS_NS is not set
+# CONFIG_IPC_NS is not set
+# CONFIG_PID_NS is not set
+# CONFIG_NET_NS is not set
CONFIG_BLK_DEV_INITRD=y
-# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_SLAB=y
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_AMIGA_PARTITION=y
+CONFIG_ATARI_PARTITION=y
+CONFIG_MAC_PARTITION=y
+CONFIG_BSD_DISKLABEL=y
+CONFIG_MINIX_SUBPARTITION=y
+CONFIG_SOLARIS_X86_PARTITION=y
+CONFIG_UNIXWARE_DISKLABEL=y
+CONFIG_SUN_PARTITION=y
+# CONFIG_EFI_PARTITION is not set
+CONFIG_IOSCHED_DEADLINE=m
+CONFIG_M68030=y
CONFIG_VME=y
CONFIG_MVME147=y
-CONFIG_M68030=y
+# CONFIG_COMPACTION is not set
+CONFIG_CLEANCACHE=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
CONFIG_BINFMT_AOUT=m
CONFIG_BINFMT_MISC=m
-CONFIG_PROC_HARDWARE=y
CONFIG_NET=y
CONFIG_PACKET=y
+CONFIG_PACKET_DIAG=m
CONFIG_UNIX=y
+CONFIG_UNIX_DIAG=m
+CONFIG_XFRM_MIGRATE=y
CONFIG_NET_KEY=y
-CONFIG_NET_KEY_MIGRATE=y
CONFIG_INET=y
CONFIG_IP_PNP=y
CONFIG_IP_PNP_DHCP=y
CONFIG_IP_PNP_BOOTP=y
CONFIG_IP_PNP_RARP=y
CONFIG_NET_IPIP=m
+CONFIG_NET_IPGRE_DEMUX=m
CONFIG_NET_IPGRE=m
CONFIG_SYN_COOKIES=y
+CONFIG_NET_IPVTI=m
CONFIG_INET_AH=m
CONFIG_INET_ESP=m
CONFIG_INET_IPCOMP=m
CONFIG_INET_XFRM_MODE_TRANSPORT=m
CONFIG_INET_XFRM_MODE_TUNNEL=m
CONFIG_INET_XFRM_MODE_BEET=m
+# CONFIG_INET_LRO is not set
CONFIG_INET_DIAG=m
+CONFIG_INET_UDP_DIAG=m
CONFIG_IPV6_PRIVACY=y
CONFIG_IPV6_ROUTER_PREF=y
-CONFIG_IPV6_ROUTE_INFO=y
CONFIG_INET6_AH=m
CONFIG_INET6_ESP=m
CONFIG_INET6_IPCOMP=m
-CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION=m
-CONFIG_IPV6_TUNNEL=m
+CONFIG_IPV6_GRE=m
CONFIG_NETFILTER=y
-CONFIG_NETFILTER_NETLINK_QUEUE=m
CONFIG_NF_CONNTRACK=m
+CONFIG_NF_CONNTRACK_ZONES=y
+# CONFIG_NF_CONNTRACK_PROCFS is not set
# CONFIG_NF_CT_PROTO_DCCP is not set
CONFIG_NF_CT_PROTO_UDPLITE=m
CONFIG_NF_CONNTRACK_AMANDA=m
CONFIG_NF_CONNTRACK_H323=m
CONFIG_NF_CONNTRACK_IRC=m
CONFIG_NF_CONNTRACK_NETBIOS_NS=m
+CONFIG_NF_CONNTRACK_SNMP=m
CONFIG_NF_CONNTRACK_PPTP=m
CONFIG_NF_CONNTRACK_SANE=m
CONFIG_NF_CONNTRACK_SIP=m
CONFIG_NF_CONNTRACK_TFTP=m
+CONFIG_NETFILTER_XT_SET=m
+CONFIG_NETFILTER_XT_TARGET_CHECKSUM=m
CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
CONFIG_NETFILTER_XT_TARGET_CONNMARK=m
CONFIG_NETFILTER_XT_TARGET_DSCP=m
+CONFIG_NETFILTER_XT_TARGET_HMARK=m
+CONFIG_NETFILTER_XT_TARGET_IDLETIMER=m
+CONFIG_NETFILTER_XT_TARGET_LOG=m
CONFIG_NETFILTER_XT_TARGET_MARK=m
CONFIG_NETFILTER_XT_TARGET_NFLOG=m
CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
+CONFIG_NETFILTER_XT_TARGET_NOTRACK=m
+CONFIG_NETFILTER_XT_TARGET_TEE=m
CONFIG_NETFILTER_XT_TARGET_TRACE=m
CONFIG_NETFILTER_XT_TARGET_TCPMSS=m
CONFIG_NETFILTER_XT_TARGET_TCPOPTSTRIP=m
+CONFIG_NETFILTER_XT_MATCH_ADDRTYPE=m
+CONFIG_NETFILTER_XT_MATCH_BPF=m
CONFIG_NETFILTER_XT_MATCH_CLUSTER=m
CONFIG_NETFILTER_XT_MATCH_COMMENT=m
CONFIG_NETFILTER_XT_MATCH_CONNBYTES=m
+CONFIG_NETFILTER_XT_MATCH_CONNLABEL=m
CONFIG_NETFILTER_XT_MATCH_CONNLIMIT=m
CONFIG_NETFILTER_XT_MATCH_CONNMARK=m
CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
+CONFIG_NETFILTER_XT_MATCH_DEVGROUP=m
CONFIG_NETFILTER_XT_MATCH_DSCP=m
CONFIG_NETFILTER_XT_MATCH_ESP=m
CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m
CONFIG_NETFILTER_XT_MATCH_MAC=m
CONFIG_NETFILTER_XT_MATCH_MARK=m
CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
+CONFIG_NETFILTER_XT_MATCH_NFACCT=m
+CONFIG_NETFILTER_XT_MATCH_OSF=m
CONFIG_NETFILTER_XT_MATCH_OWNER=m
CONFIG_NETFILTER_XT_MATCH_POLICY=m
CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m
CONFIG_NETFILTER_XT_MATCH_TCPMSS=m
CONFIG_NETFILTER_XT_MATCH_TIME=m
CONFIG_NETFILTER_XT_MATCH_U32=m
+CONFIG_IP_SET=m
+CONFIG_IP_SET_BITMAP_IP=m
+CONFIG_IP_SET_BITMAP_IPMAC=m
+CONFIG_IP_SET_BITMAP_PORT=m
+CONFIG_IP_SET_HASH_IP=m
+CONFIG_IP_SET_HASH_IPPORT=m
+CONFIG_IP_SET_HASH_IPPORTIP=m
+CONFIG_IP_SET_HASH_IPPORTNET=m
+CONFIG_IP_SET_HASH_NET=m
+CONFIG_IP_SET_HASH_NETPORT=m
+CONFIG_IP_SET_HASH_NETIFACE=m
+CONFIG_IP_SET_LIST_SET=m
CONFIG_NF_CONNTRACK_IPV4=m
-CONFIG_IP_NF_QUEUE=m
CONFIG_IP_NF_IPTABLES=m
-CONFIG_IP_NF_MATCH_ADDRTYPE=m
CONFIG_IP_NF_MATCH_AH=m
CONFIG_IP_NF_MATCH_ECN=m
+CONFIG_IP_NF_MATCH_RPFILTER=m
CONFIG_IP_NF_MATCH_TTL=m
CONFIG_IP_NF_FILTER=m
CONFIG_IP_NF_TARGET_REJECT=m
-CONFIG_IP_NF_TARGET_LOG=m
CONFIG_IP_NF_TARGET_ULOG=m
-CONFIG_NF_NAT=m
+CONFIG_NF_NAT_IPV4=m
CONFIG_IP_NF_TARGET_MASQUERADE=m
CONFIG_IP_NF_TARGET_NETMAP=m
CONFIG_IP_NF_TARGET_REDIRECT=m
-CONFIG_NF_NAT_SNMP_BASIC=m
CONFIG_IP_NF_MANGLE=m
CONFIG_IP_NF_TARGET_CLUSTERIP=m
CONFIG_IP_NF_TARGET_ECN=m
CONFIG_IP_NF_ARPFILTER=m
CONFIG_IP_NF_ARP_MANGLE=m
CONFIG_NF_CONNTRACK_IPV6=m
-CONFIG_IP6_NF_QUEUE=m
CONFIG_IP6_NF_IPTABLES=m
CONFIG_IP6_NF_MATCH_AH=m
CONFIG_IP6_NF_MATCH_EUI64=m
CONFIG_IP6_NF_MATCH_HL=m
CONFIG_IP6_NF_MATCH_IPV6HEADER=m
CONFIG_IP6_NF_MATCH_MH=m
+CONFIG_IP6_NF_MATCH_RPFILTER=m
CONFIG_IP6_NF_MATCH_RT=m
CONFIG_IP6_NF_TARGET_HL=m
-CONFIG_IP6_NF_TARGET_LOG=m
CONFIG_IP6_NF_FILTER=m
CONFIG_IP6_NF_TARGET_REJECT=m
CONFIG_IP6_NF_MANGLE=m
CONFIG_IP6_NF_RAW=m
+CONFIG_NF_NAT_IPV6=m
+CONFIG_IP6_NF_TARGET_MASQUERADE=m
+CONFIG_IP6_NF_TARGET_NPT=m
CONFIG_IP_DCCP=m
# CONFIG_IP_DCCP_CCID3 is not set
+CONFIG_SCTP_COOKIE_HMAC_SHA1=y
+CONFIG_RDS=m
+CONFIG_RDS_TCP=m
+CONFIG_L2TP=m
CONFIG_ATALK=m
+CONFIG_BATMAN_ADV=m
+CONFIG_BATMAN_ADV_DAT=y
+# CONFIG_WIRELESS is not set
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
# CONFIG_FIRMWARE_IN_KERNEL is not set
+# CONFIG_FW_LOADER_USER_HELPER is not set
CONFIG_CONNECTOR=m
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_CRYPTOLOOP=m
+CONFIG_BLK_DEV_DRBD=m
CONFIG_BLK_DEV_NBD=m
CONFIG_BLK_DEV_RAM=y
CONFIG_CDROM_PKTCDVD=m
CONFIG_BLK_DEV_SR_VENDOR=y
CONFIG_CHR_DEV_SG=m
CONFIG_SCSI_CONSTANTS=y
-CONFIG_SCSI_SAS_LIBSAS=m
-# CONFIG_SCSI_SAS_LIBSAS_DEBUG is not set
-CONFIG_SCSI_SRP_ATTRS=m
-CONFIG_SCSI_SRP_TGT_ATTRS=y
+CONFIG_SCSI_SAS_ATTRS=m
CONFIG_ISCSI_TCP=m
+CONFIG_ISCSI_BOOT_SYSFS=m
CONFIG_MVME147_SCSI=y
CONFIG_MD=y
-CONFIG_BLK_DEV_MD=m
CONFIG_MD_LINEAR=m
CONFIG_MD_RAID0=m
-CONFIG_MD_RAID1=m
-CONFIG_MD_RAID456=m
CONFIG_BLK_DEV_DM=m
CONFIG_DM_CRYPT=m
CONFIG_DM_SNAPSHOT=m
+CONFIG_DM_THIN_PROVISIONING=m
+CONFIG_DM_CACHE=m
CONFIG_DM_MIRROR=m
+CONFIG_DM_RAID=m
CONFIG_DM_ZERO=m
CONFIG_DM_MULTIPATH=m
CONFIG_DM_UEVENT=y
+CONFIG_TARGET_CORE=m
+CONFIG_TCM_IBLOCK=m
+CONFIG_TCM_FILEIO=m
+CONFIG_TCM_PSCSI=m
CONFIG_NETDEVICES=y
CONFIG_DUMMY=m
-CONFIG_MACVLAN=m
CONFIG_EQUALIZER=m
+CONFIG_NET_TEAM=m
+CONFIG_NET_TEAM_MODE_BROADCAST=m
+CONFIG_NET_TEAM_MODE_ROUNDROBIN=m
+CONFIG_NET_TEAM_MODE_ACTIVEBACKUP=m
+CONFIG_NET_TEAM_MODE_LOADBALANCE=m
+CONFIG_VXLAN=m
+CONFIG_NETCONSOLE=m
+CONFIG_NETCONSOLE_DYNAMIC=y
CONFIG_VETH=m
-CONFIG_NET_ETHERNET=y
CONFIG_MVME147_NET=y
-# CONFIG_NETDEV_1000 is not set
-# CONFIG_NETDEV_10000 is not set
+# CONFIG_NET_CADENCE is not set
+# CONFIG_NET_VENDOR_BROADCOM is not set
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_WIZNET is not set
CONFIG_PPP=m
-CONFIG_PPP_FILTER=y
-CONFIG_PPP_ASYNC=m
-CONFIG_PPP_SYNC_TTY=m
-CONFIG_PPP_DEFLATE=m
CONFIG_PPP_BSDCOMP=m
+CONFIG_PPP_DEFLATE=m
+CONFIG_PPP_FILTER=y
CONFIG_PPP_MPPE=m
CONFIG_PPPOE=m
+CONFIG_PPTP=m
+CONFIG_PPPOL2TP=m
+CONFIG_PPP_ASYNC=m
+CONFIG_PPP_SYNC_TTY=m
CONFIG_SLIP=m
CONFIG_SLIP_COMPRESSED=y
CONFIG_SLIP_SMART=y
CONFIG_SLIP_MODE_SLIP6=y
-CONFIG_NETCONSOLE=m
-CONFIG_NETCONSOLE_DYNAMIC=y
-CONFIG_INPUT_FF_MEMLESS=m
+# CONFIG_WLAN is not set
+CONFIG_INPUT_EVDEV=m
# CONFIG_KEYBOARD_ATKBD is not set
-CONFIG_MOUSE_PS2=m
-CONFIG_MOUSE_SERIAL=m
-CONFIG_SERIO=m
-# CONFIG_SERIO_SERPORT is not set
+# CONFIG_MOUSE_PS2 is not set
+# CONFIG_SERIO is not set
CONFIG_VT_HW_CONSOLE_BINDING=y
+# CONFIG_LEGACY_PTYS is not set
# CONFIG_DEVKMEM is not set
# CONFIG_HW_RANDOM is not set
-CONFIG_GEN_RTC=m
-CONFIG_GEN_RTC_X=y
+CONFIG_NTP_PPS=y
+CONFIG_PPS_CLIENT_LDISC=m
+CONFIG_PTP_1588_CLOCK=m
# CONFIG_HWMON is not set
CONFIG_HID=m
CONFIG_HIDRAW=y
+CONFIG_UHID=m
+# CONFIG_HID_GENERIC is not set
# CONFIG_USB_SUPPORT is not set
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_GENERIC=m
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_PROC_HARDWARE=y
CONFIG_EXT2_FS=y
CONFIG_EXT3_FS=y
# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
# CONFIG_EXT3_FS_XATTR is not set
+CONFIG_EXT4_FS=y
CONFIG_REISERFS_FS=m
CONFIG_JFS_FS=m
CONFIG_XFS_FS=m
CONFIG_OCFS2_FS=m
-# CONFIG_OCFS2_FS_STATS is not set
# CONFIG_OCFS2_DEBUG_MASKLOG is not set
+CONFIG_FANOTIFY=y
CONFIG_QUOTA_NETLINK_INTERFACE=y
# CONFIG_PRINT_QUOTA_WARNING is not set
-CONFIG_AUTOFS_FS=m
CONFIG_AUTOFS4_FS=m
CONFIG_FUSE_FS=m
+CONFIG_CUSE=m
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
CONFIG_UDF_FS=m
-CONFIG_MSDOS_FS=y
+CONFIG_MSDOS_FS=m
CONFIG_VFAT_FS=m
CONFIG_PROC_KCORE=y
CONFIG_TMPFS=y
CONFIG_AFFS_FS=m
+CONFIG_ECRYPT_FS=m
+CONFIG_ECRYPT_FS_MESSAGING=y
CONFIG_HFS_FS=m
CONFIG_HFSPLUS_FS=m
CONFIG_CRAMFS=m
CONFIG_SQUASHFS=m
-CONFIG_MINIX_FS=y
+CONFIG_SQUASHFS_LZO=y
+CONFIG_MINIX_FS=m
+CONFIG_OMFS_FS=m
CONFIG_HPFS_FS=m
+CONFIG_QNX4FS_FS=m
+CONFIG_QNX6FS_FS=m
CONFIG_SYSV_FS=m
CONFIG_UFS_FS=m
CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
CONFIG_NFS_V4=y
+CONFIG_NFS_SWAP=y
CONFIG_ROOT_NFS=y
CONFIG_NFSD=m
CONFIG_NFSD_V3=y
-CONFIG_SMB_FS=m
-CONFIG_SMB_NLS_DEFAULT=y
+CONFIG_CIFS=m
+# CONFIG_CIFS_DEBUG is not set
CONFIG_CODA_FS=m
CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_CODEPAGE_737=m
CONFIG_NLS_ISO8859_15=m
CONFIG_NLS_KOI8_R=m
CONFIG_NLS_KOI8_U=m
+CONFIG_NLS_MAC_ROMAN=m
+CONFIG_NLS_MAC_CELTIC=m
+CONFIG_NLS_MAC_CENTEURO=m
+CONFIG_NLS_MAC_CROATIAN=m
+CONFIG_NLS_MAC_CYRILLIC=m
+CONFIG_NLS_MAC_GAELIC=m
+CONFIG_NLS_MAC_GREEK=m
+CONFIG_NLS_MAC_ICELAND=m
+CONFIG_NLS_MAC_INUIT=m
+CONFIG_NLS_MAC_ROMANIAN=m
+CONFIG_NLS_MAC_TURKISH=m
CONFIG_DLM=m
CONFIG_MAGIC_SYSRQ=y
-# CONFIG_RCU_CPU_STALL_DETECTOR is not set
-CONFIG_SYSCTL_SYSCALL_CHECK=y
+CONFIG_ASYNC_RAID6_TEST=m
+CONFIG_ENCRYPTED_KEYS=m
+CONFIG_CRYPTO_MANAGER=y
+CONFIG_CRYPTO_USER=m
CONFIG_CRYPTO_NULL=m
CONFIG_CRYPTO_CRYPTD=m
CONFIG_CRYPTO_TEST=m
CONFIG_CRYPTO_LRW=m
CONFIG_CRYPTO_PCBC=m
CONFIG_CRYPTO_XTS=m
-CONFIG_CRYPTO_HMAC=y
CONFIG_CRYPTO_XCBC=m
-CONFIG_CRYPTO_MD4=m
+CONFIG_CRYPTO_VMAC=m
CONFIG_CRYPTO_MICHAEL_MIC=m
CONFIG_CRYPTO_RMD128=m
CONFIG_CRYPTO_RMD160=m
CONFIG_CRYPTO_RMD256=m
CONFIG_CRYPTO_RMD320=m
-CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
CONFIG_CRYPTO_TGR192=m
CONFIG_CRYPTO_WP512=m
-CONFIG_CRYPTO_AES=m
CONFIG_CRYPTO_ANUBIS=m
CONFIG_CRYPTO_BLOWFISH=m
CONFIG_CRYPTO_CAMELLIA=m
CONFIG_CRYPTO_ZLIB=m
CONFIG_CRYPTO_LZO=m
# CONFIG_CRYPTO_ANSI_CPRNG is not set
+CONFIG_CRYPTO_USER_API_HASH=m
+CONFIG_CRYPTO_USER_API_SKCIPHER=m
# CONFIG_CRYPTO_HW is not set
-CONFIG_CRC16=m
CONFIG_CRC_T10DIF=y
+CONFIG_XZ_DEC_X86=y
+CONFIG_XZ_DEC_POWERPC=y
+CONFIG_XZ_DEC_IA64=y
+CONFIG_XZ_DEC_ARM=y
+CONFIG_XZ_DEC_ARMTHUMB=y
+CONFIG_XZ_DEC_SPARC=y
+CONFIG_XZ_DEC_TEST=m
-CONFIG_EXPERIMENTAL=y
CONFIG_LOCALVERSION="-mvme16x"
CONFIG_SYSVIPC=y
CONFIG_POSIX_MQUEUE=y
+CONFIG_FHANDLE=y
CONFIG_BSD_PROCESS_ACCT=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_RELAY=y
+CONFIG_BSD_PROCESS_ACCT_V3=y
+CONFIG_LOG_BUF_SHIFT=16
+# CONFIG_UTS_NS is not set
+# CONFIG_IPC_NS is not set
+# CONFIG_PID_NS is not set
+# CONFIG_NET_NS is not set
CONFIG_BLK_DEV_INITRD=y
-# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_SLAB=y
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
-CONFIG_VME=y
-CONFIG_MVME16x=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_AMIGA_PARTITION=y
+CONFIG_ATARI_PARTITION=y
+CONFIG_MAC_PARTITION=y
+CONFIG_BSD_DISKLABEL=y
+CONFIG_MINIX_SUBPARTITION=y
+CONFIG_SOLARIS_X86_PARTITION=y
+CONFIG_UNIXWARE_DISKLABEL=y
+CONFIG_SUN_PARTITION=y
+# CONFIG_EFI_PARTITION is not set
+CONFIG_IOSCHED_DEADLINE=m
CONFIG_M68040=y
CONFIG_M68060=y
+CONFIG_VME=y
+CONFIG_MVME16x=y
+# CONFIG_COMPACTION is not set
+CONFIG_CLEANCACHE=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
CONFIG_BINFMT_AOUT=m
CONFIG_BINFMT_MISC=m
-CONFIG_PROC_HARDWARE=y
CONFIG_NET=y
CONFIG_PACKET=y
+CONFIG_PACKET_DIAG=m
CONFIG_UNIX=y
+CONFIG_UNIX_DIAG=m
+CONFIG_XFRM_MIGRATE=y
CONFIG_NET_KEY=y
-CONFIG_NET_KEY_MIGRATE=y
CONFIG_INET=y
CONFIG_IP_PNP=y
CONFIG_IP_PNP_DHCP=y
CONFIG_IP_PNP_BOOTP=y
CONFIG_IP_PNP_RARP=y
CONFIG_NET_IPIP=m
+CONFIG_NET_IPGRE_DEMUX=m
CONFIG_NET_IPGRE=m
CONFIG_SYN_COOKIES=y
+CONFIG_NET_IPVTI=m
CONFIG_INET_AH=m
CONFIG_INET_ESP=m
CONFIG_INET_IPCOMP=m
CONFIG_INET_XFRM_MODE_TRANSPORT=m
CONFIG_INET_XFRM_MODE_TUNNEL=m
CONFIG_INET_XFRM_MODE_BEET=m
+# CONFIG_INET_LRO is not set
CONFIG_INET_DIAG=m
+CONFIG_INET_UDP_DIAG=m
CONFIG_IPV6_PRIVACY=y
CONFIG_IPV6_ROUTER_PREF=y
-CONFIG_IPV6_ROUTE_INFO=y
CONFIG_INET6_AH=m
CONFIG_INET6_ESP=m
CONFIG_INET6_IPCOMP=m
-CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION=m
-CONFIG_IPV6_TUNNEL=m
+CONFIG_IPV6_GRE=m
CONFIG_NETFILTER=y
-CONFIG_NETFILTER_NETLINK_QUEUE=m
CONFIG_NF_CONNTRACK=m
+CONFIG_NF_CONNTRACK_ZONES=y
+# CONFIG_NF_CONNTRACK_PROCFS is not set
# CONFIG_NF_CT_PROTO_DCCP is not set
CONFIG_NF_CT_PROTO_UDPLITE=m
CONFIG_NF_CONNTRACK_AMANDA=m
CONFIG_NF_CONNTRACK_H323=m
CONFIG_NF_CONNTRACK_IRC=m
CONFIG_NF_CONNTRACK_NETBIOS_NS=m
+CONFIG_NF_CONNTRACK_SNMP=m
CONFIG_NF_CONNTRACK_PPTP=m
CONFIG_NF_CONNTRACK_SANE=m
CONFIG_NF_CONNTRACK_SIP=m
CONFIG_NF_CONNTRACK_TFTP=m
+CONFIG_NETFILTER_XT_SET=m
+CONFIG_NETFILTER_XT_TARGET_CHECKSUM=m
CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
CONFIG_NETFILTER_XT_TARGET_CONNMARK=m
CONFIG_NETFILTER_XT_TARGET_DSCP=m
+CONFIG_NETFILTER_XT_TARGET_HMARK=m
+CONFIG_NETFILTER_XT_TARGET_IDLETIMER=m
+CONFIG_NETFILTER_XT_TARGET_LOG=m
CONFIG_NETFILTER_XT_TARGET_MARK=m
CONFIG_NETFILTER_XT_TARGET_NFLOG=m
CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
+CONFIG_NETFILTER_XT_TARGET_NOTRACK=m
+CONFIG_NETFILTER_XT_TARGET_TEE=m
CONFIG_NETFILTER_XT_TARGET_TRACE=m
CONFIG_NETFILTER_XT_TARGET_TCPMSS=m
CONFIG_NETFILTER_XT_TARGET_TCPOPTSTRIP=m
+CONFIG_NETFILTER_XT_MATCH_ADDRTYPE=m
+CONFIG_NETFILTER_XT_MATCH_BPF=m
CONFIG_NETFILTER_XT_MATCH_CLUSTER=m
CONFIG_NETFILTER_XT_MATCH_COMMENT=m
CONFIG_NETFILTER_XT_MATCH_CONNBYTES=m
+CONFIG_NETFILTER_XT_MATCH_CONNLABEL=m
CONFIG_NETFILTER_XT_MATCH_CONNLIMIT=m
CONFIG_NETFILTER_XT_MATCH_CONNMARK=m
CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
+CONFIG_NETFILTER_XT_MATCH_DEVGROUP=m
CONFIG_NETFILTER_XT_MATCH_DSCP=m
CONFIG_NETFILTER_XT_MATCH_ESP=m
CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m
CONFIG_NETFILTER_XT_MATCH_MAC=m
CONFIG_NETFILTER_XT_MATCH_MARK=m
CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
+CONFIG_NETFILTER_XT_MATCH_NFACCT=m
+CONFIG_NETFILTER_XT_MATCH_OSF=m
CONFIG_NETFILTER_XT_MATCH_OWNER=m
CONFIG_NETFILTER_XT_MATCH_POLICY=m
CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m
CONFIG_NETFILTER_XT_MATCH_TCPMSS=m
CONFIG_NETFILTER_XT_MATCH_TIME=m
CONFIG_NETFILTER_XT_MATCH_U32=m
+CONFIG_IP_SET=m
+CONFIG_IP_SET_BITMAP_IP=m
+CONFIG_IP_SET_BITMAP_IPMAC=m
+CONFIG_IP_SET_BITMAP_PORT=m
+CONFIG_IP_SET_HASH_IP=m
+CONFIG_IP_SET_HASH_IPPORT=m
+CONFIG_IP_SET_HASH_IPPORTIP=m
+CONFIG_IP_SET_HASH_IPPORTNET=m
+CONFIG_IP_SET_HASH_NET=m
+CONFIG_IP_SET_HASH_NETPORT=m
+CONFIG_IP_SET_HASH_NETIFACE=m
+CONFIG_IP_SET_LIST_SET=m
CONFIG_NF_CONNTRACK_IPV4=m
-CONFIG_IP_NF_QUEUE=m
CONFIG_IP_NF_IPTABLES=m
-CONFIG_IP_NF_MATCH_ADDRTYPE=m
CONFIG_IP_NF_MATCH_AH=m
CONFIG_IP_NF_MATCH_ECN=m
+CONFIG_IP_NF_MATCH_RPFILTER=m
CONFIG_IP_NF_MATCH_TTL=m
CONFIG_IP_NF_FILTER=m
CONFIG_IP_NF_TARGET_REJECT=m
-CONFIG_IP_NF_TARGET_LOG=m
CONFIG_IP_NF_TARGET_ULOG=m
-CONFIG_NF_NAT=m
+CONFIG_NF_NAT_IPV4=m
CONFIG_IP_NF_TARGET_MASQUERADE=m
CONFIG_IP_NF_TARGET_NETMAP=m
CONFIG_IP_NF_TARGET_REDIRECT=m
-CONFIG_NF_NAT_SNMP_BASIC=m
CONFIG_IP_NF_MANGLE=m
CONFIG_IP_NF_TARGET_CLUSTERIP=m
CONFIG_IP_NF_TARGET_ECN=m
CONFIG_IP_NF_ARPFILTER=m
CONFIG_IP_NF_ARP_MANGLE=m
CONFIG_NF_CONNTRACK_IPV6=m
-CONFIG_IP6_NF_QUEUE=m
CONFIG_IP6_NF_IPTABLES=m
CONFIG_IP6_NF_MATCH_AH=m
CONFIG_IP6_NF_MATCH_EUI64=m
CONFIG_IP6_NF_MATCH_HL=m
CONFIG_IP6_NF_MATCH_IPV6HEADER=m
CONFIG_IP6_NF_MATCH_MH=m
+CONFIG_IP6_NF_MATCH_RPFILTER=m
CONFIG_IP6_NF_MATCH_RT=m
CONFIG_IP6_NF_TARGET_HL=m
-CONFIG_IP6_NF_TARGET_LOG=m
CONFIG_IP6_NF_FILTER=m
CONFIG_IP6_NF_TARGET_REJECT=m
CONFIG_IP6_NF_MANGLE=m
CONFIG_IP6_NF_RAW=m
+CONFIG_NF_NAT_IPV6=m
+CONFIG_IP6_NF_TARGET_MASQUERADE=m
+CONFIG_IP6_NF_TARGET_NPT=m
CONFIG_IP_DCCP=m
# CONFIG_IP_DCCP_CCID3 is not set
+CONFIG_SCTP_COOKIE_HMAC_SHA1=y
+CONFIG_RDS=m
+CONFIG_RDS_TCP=m
+CONFIG_L2TP=m
CONFIG_ATALK=m
+CONFIG_BATMAN_ADV=m
+CONFIG_BATMAN_ADV_DAT=y
+# CONFIG_WIRELESS is not set
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
# CONFIG_FIRMWARE_IN_KERNEL is not set
+# CONFIG_FW_LOADER_USER_HELPER is not set
CONFIG_CONNECTOR=m
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_CRYPTOLOOP=m
+CONFIG_BLK_DEV_DRBD=m
CONFIG_BLK_DEV_NBD=m
CONFIG_BLK_DEV_RAM=y
CONFIG_CDROM_PKTCDVD=m
CONFIG_BLK_DEV_SR_VENDOR=y
CONFIG_CHR_DEV_SG=m
CONFIG_SCSI_CONSTANTS=y
-CONFIG_SCSI_SAS_LIBSAS=m
-# CONFIG_SCSI_SAS_LIBSAS_DEBUG is not set
-CONFIG_SCSI_SRP_ATTRS=m
-CONFIG_SCSI_SRP_TGT_ATTRS=y
+CONFIG_SCSI_SAS_ATTRS=m
CONFIG_ISCSI_TCP=m
+CONFIG_ISCSI_BOOT_SYSFS=m
CONFIG_MVME16x_SCSI=y
CONFIG_MD=y
-CONFIG_BLK_DEV_MD=m
CONFIG_MD_LINEAR=m
CONFIG_MD_RAID0=m
-CONFIG_MD_RAID1=m
-CONFIG_MD_RAID456=m
CONFIG_BLK_DEV_DM=m
CONFIG_DM_CRYPT=m
CONFIG_DM_SNAPSHOT=m
+CONFIG_DM_THIN_PROVISIONING=m
+CONFIG_DM_CACHE=m
CONFIG_DM_MIRROR=m
+CONFIG_DM_RAID=m
CONFIG_DM_ZERO=m
CONFIG_DM_MULTIPATH=m
CONFIG_DM_UEVENT=y
+CONFIG_TARGET_CORE=m
+CONFIG_TCM_IBLOCK=m
+CONFIG_TCM_FILEIO=m
+CONFIG_TCM_PSCSI=m
CONFIG_NETDEVICES=y
CONFIG_DUMMY=m
-CONFIG_MACVLAN=m
CONFIG_EQUALIZER=m
+CONFIG_NET_TEAM=m
+CONFIG_NET_TEAM_MODE_BROADCAST=m
+CONFIG_NET_TEAM_MODE_ROUNDROBIN=m
+CONFIG_NET_TEAM_MODE_ACTIVEBACKUP=m
+CONFIG_NET_TEAM_MODE_LOADBALANCE=m
+CONFIG_VXLAN=m
+CONFIG_NETCONSOLE=m
+CONFIG_NETCONSOLE_DYNAMIC=y
CONFIG_VETH=m
-CONFIG_NET_ETHERNET=y
+# CONFIG_NET_CADENCE is not set
+# CONFIG_NET_VENDOR_BROADCOM is not set
CONFIG_MVME16x_NET=y
-# CONFIG_NETDEV_1000 is not set
-# CONFIG_NETDEV_10000 is not set
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_WIZNET is not set
CONFIG_PPP=m
-CONFIG_PPP_FILTER=y
-CONFIG_PPP_ASYNC=m
-CONFIG_PPP_SYNC_TTY=m
-CONFIG_PPP_DEFLATE=m
CONFIG_PPP_BSDCOMP=m
+CONFIG_PPP_DEFLATE=m
+CONFIG_PPP_FILTER=y
CONFIG_PPP_MPPE=m
CONFIG_PPPOE=m
+CONFIG_PPTP=m
+CONFIG_PPPOL2TP=m
+CONFIG_PPP_ASYNC=m
+CONFIG_PPP_SYNC_TTY=m
CONFIG_SLIP=m
CONFIG_SLIP_COMPRESSED=y
CONFIG_SLIP_SMART=y
CONFIG_SLIP_MODE_SLIP6=y
-CONFIG_NETCONSOLE=m
-CONFIG_NETCONSOLE_DYNAMIC=y
-CONFIG_INPUT_FF_MEMLESS=m
+# CONFIG_WLAN is not set
+CONFIG_INPUT_EVDEV=m
# CONFIG_KEYBOARD_ATKBD is not set
-CONFIG_MOUSE_PS2=m
-CONFIG_MOUSE_SERIAL=m
-CONFIG_SERIO=m
-# CONFIG_SERIO_SERPORT is not set
+# CONFIG_MOUSE_PS2 is not set
+# CONFIG_SERIO is not set
CONFIG_VT_HW_CONSOLE_BINDING=y
+# CONFIG_LEGACY_PTYS is not set
# CONFIG_DEVKMEM is not set
# CONFIG_HW_RANDOM is not set
-CONFIG_GEN_RTC=m
-CONFIG_GEN_RTC_X=y
+CONFIG_NTP_PPS=y
+CONFIG_PPS_CLIENT_LDISC=m
+CONFIG_PTP_1588_CLOCK=m
# CONFIG_HWMON is not set
CONFIG_HID=m
CONFIG_HIDRAW=y
+CONFIG_UHID=m
+# CONFIG_HID_GENERIC is not set
# CONFIG_USB_SUPPORT is not set
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_GENERIC=m
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_PROC_HARDWARE=y
CONFIG_EXT2_FS=y
CONFIG_EXT3_FS=y
# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
# CONFIG_EXT3_FS_XATTR is not set
+CONFIG_EXT4_FS=y
CONFIG_REISERFS_FS=m
CONFIG_JFS_FS=m
CONFIG_XFS_FS=m
CONFIG_OCFS2_FS=m
-# CONFIG_OCFS2_FS_STATS is not set
# CONFIG_OCFS2_DEBUG_MASKLOG is not set
+CONFIG_FANOTIFY=y
CONFIG_QUOTA_NETLINK_INTERFACE=y
# CONFIG_PRINT_QUOTA_WARNING is not set
-CONFIG_AUTOFS_FS=m
CONFIG_AUTOFS4_FS=m
CONFIG_FUSE_FS=m
+CONFIG_CUSE=m
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
CONFIG_UDF_FS=m
-CONFIG_MSDOS_FS=y
+CONFIG_MSDOS_FS=m
CONFIG_VFAT_FS=m
CONFIG_PROC_KCORE=y
CONFIG_TMPFS=y
CONFIG_AFFS_FS=m
+CONFIG_ECRYPT_FS=m
+CONFIG_ECRYPT_FS_MESSAGING=y
CONFIG_HFS_FS=m
CONFIG_HFSPLUS_FS=m
CONFIG_CRAMFS=m
CONFIG_SQUASHFS=m
-CONFIG_MINIX_FS=y
+CONFIG_SQUASHFS_LZO=y
+CONFIG_MINIX_FS=m
+CONFIG_OMFS_FS=m
CONFIG_HPFS_FS=m
+CONFIG_QNX4FS_FS=m
+CONFIG_QNX6FS_FS=m
CONFIG_SYSV_FS=m
CONFIG_UFS_FS=m
CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
CONFIG_NFS_V4=y
+CONFIG_NFS_SWAP=y
CONFIG_ROOT_NFS=y
CONFIG_NFSD=m
CONFIG_NFSD_V3=y
-CONFIG_SMB_FS=m
-CONFIG_SMB_NLS_DEFAULT=y
+CONFIG_CIFS=m
+# CONFIG_CIFS_DEBUG is not set
CONFIG_CODA_FS=m
CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_CODEPAGE_737=m
CONFIG_NLS_ISO8859_15=m
CONFIG_NLS_KOI8_R=m
CONFIG_NLS_KOI8_U=m
+CONFIG_NLS_MAC_ROMAN=m
+CONFIG_NLS_MAC_CELTIC=m
+CONFIG_NLS_MAC_CENTEURO=m
+CONFIG_NLS_MAC_CROATIAN=m
+CONFIG_NLS_MAC_CYRILLIC=m
+CONFIG_NLS_MAC_GAELIC=m
+CONFIG_NLS_MAC_GREEK=m
+CONFIG_NLS_MAC_ICELAND=m
+CONFIG_NLS_MAC_INUIT=m
+CONFIG_NLS_MAC_ROMANIAN=m
+CONFIG_NLS_MAC_TURKISH=m
CONFIG_DLM=m
CONFIG_MAGIC_SYSRQ=y
-# CONFIG_RCU_CPU_STALL_DETECTOR is not set
-CONFIG_SYSCTL_SYSCALL_CHECK=y
+CONFIG_ASYNC_RAID6_TEST=m
+CONFIG_ENCRYPTED_KEYS=m
+CONFIG_CRYPTO_MANAGER=y
+CONFIG_CRYPTO_USER=m
CONFIG_CRYPTO_NULL=m
CONFIG_CRYPTO_CRYPTD=m
CONFIG_CRYPTO_TEST=m
CONFIG_CRYPTO_LRW=m
CONFIG_CRYPTO_PCBC=m
CONFIG_CRYPTO_XTS=m
-CONFIG_CRYPTO_HMAC=y
CONFIG_CRYPTO_XCBC=m
-CONFIG_CRYPTO_MD4=m
+CONFIG_CRYPTO_VMAC=m
CONFIG_CRYPTO_MICHAEL_MIC=m
CONFIG_CRYPTO_RMD128=m
CONFIG_CRYPTO_RMD160=m
CONFIG_CRYPTO_RMD256=m
CONFIG_CRYPTO_RMD320=m
-CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
CONFIG_CRYPTO_TGR192=m
CONFIG_CRYPTO_WP512=m
-CONFIG_CRYPTO_AES=m
CONFIG_CRYPTO_ANUBIS=m
CONFIG_CRYPTO_BLOWFISH=m
CONFIG_CRYPTO_CAMELLIA=m
CONFIG_CRYPTO_ZLIB=m
CONFIG_CRYPTO_LZO=m
# CONFIG_CRYPTO_ANSI_CPRNG is not set
+CONFIG_CRYPTO_USER_API_HASH=m
+CONFIG_CRYPTO_USER_API_SKCIPHER=m
# CONFIG_CRYPTO_HW is not set
-CONFIG_CRC16=m
CONFIG_CRC_T10DIF=y
+CONFIG_XZ_DEC_X86=y
+CONFIG_XZ_DEC_POWERPC=y
+CONFIG_XZ_DEC_IA64=y
+CONFIG_XZ_DEC_ARM=y
+CONFIG_XZ_DEC_ARMTHUMB=y
+CONFIG_XZ_DEC_SPARC=y
+CONFIG_XZ_DEC_TEST=m
-CONFIG_EXPERIMENTAL=y
CONFIG_LOCALVERSION="-q40"
CONFIG_SYSVIPC=y
CONFIG_POSIX_MQUEUE=y
+CONFIG_FHANDLE=y
CONFIG_BSD_PROCESS_ACCT=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_RELAY=y
+CONFIG_BSD_PROCESS_ACCT_V3=y
+CONFIG_LOG_BUF_SHIFT=16
+# CONFIG_UTS_NS is not set
+# CONFIG_IPC_NS is not set
+# CONFIG_PID_NS is not set
+# CONFIG_NET_NS is not set
CONFIG_BLK_DEV_INITRD=y
-# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_SLAB=y
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
-CONFIG_Q40=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_AMIGA_PARTITION=y
+CONFIG_ATARI_PARTITION=y
+CONFIG_MAC_PARTITION=y
+CONFIG_BSD_DISKLABEL=y
+CONFIG_MINIX_SUBPARTITION=y
+CONFIG_SOLARIS_X86_PARTITION=y
+CONFIG_UNIXWARE_DISKLABEL=y
+CONFIG_SUN_PARTITION=y
+# CONFIG_EFI_PARTITION is not set
+CONFIG_SYSV68_PARTITION=y
+CONFIG_IOSCHED_DEADLINE=m
CONFIG_M68040=y
CONFIG_M68060=y
+CONFIG_Q40=y
+# CONFIG_COMPACTION is not set
+CONFIG_CLEANCACHE=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
CONFIG_BINFMT_AOUT=m
CONFIG_BINFMT_MISC=m
-CONFIG_HEARTBEAT=y
-CONFIG_PROC_HARDWARE=y
CONFIG_NET=y
CONFIG_PACKET=y
+CONFIG_PACKET_DIAG=m
CONFIG_UNIX=y
+CONFIG_UNIX_DIAG=m
+CONFIG_XFRM_MIGRATE=y
CONFIG_NET_KEY=y
-CONFIG_NET_KEY_MIGRATE=y
CONFIG_INET=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_IP_PNP_RARP=y
CONFIG_NET_IPIP=m
+CONFIG_NET_IPGRE_DEMUX=m
CONFIG_NET_IPGRE=m
CONFIG_SYN_COOKIES=y
+CONFIG_NET_IPVTI=m
CONFIG_INET_AH=m
CONFIG_INET_ESP=m
CONFIG_INET_IPCOMP=m
CONFIG_INET_XFRM_MODE_TRANSPORT=m
CONFIG_INET_XFRM_MODE_TUNNEL=m
CONFIG_INET_XFRM_MODE_BEET=m
+# CONFIG_INET_LRO is not set
CONFIG_INET_DIAG=m
+CONFIG_INET_UDP_DIAG=m
CONFIG_IPV6_PRIVACY=y
CONFIG_IPV6_ROUTER_PREF=y
-CONFIG_IPV6_ROUTE_INFO=y
CONFIG_INET6_AH=m
CONFIG_INET6_ESP=m
CONFIG_INET6_IPCOMP=m
-CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION=m
-CONFIG_IPV6_TUNNEL=m
+CONFIG_IPV6_GRE=m
CONFIG_NETFILTER=y
-CONFIG_NETFILTER_NETLINK_QUEUE=m
CONFIG_NF_CONNTRACK=m
+CONFIG_NF_CONNTRACK_ZONES=y
+# CONFIG_NF_CONNTRACK_PROCFS is not set
# CONFIG_NF_CT_PROTO_DCCP is not set
CONFIG_NF_CT_PROTO_UDPLITE=m
CONFIG_NF_CONNTRACK_AMANDA=m
CONFIG_NF_CONNTRACK_H323=m
CONFIG_NF_CONNTRACK_IRC=m
CONFIG_NF_CONNTRACK_NETBIOS_NS=m
+CONFIG_NF_CONNTRACK_SNMP=m
CONFIG_NF_CONNTRACK_PPTP=m
CONFIG_NF_CONNTRACK_SANE=m
CONFIG_NF_CONNTRACK_SIP=m
CONFIG_NF_CONNTRACK_TFTP=m
+CONFIG_NETFILTER_XT_SET=m
+CONFIG_NETFILTER_XT_TARGET_CHECKSUM=m
CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
CONFIG_NETFILTER_XT_TARGET_CONNMARK=m
CONFIG_NETFILTER_XT_TARGET_DSCP=m
+CONFIG_NETFILTER_XT_TARGET_HMARK=m
+CONFIG_NETFILTER_XT_TARGET_IDLETIMER=m
+CONFIG_NETFILTER_XT_TARGET_LOG=m
CONFIG_NETFILTER_XT_TARGET_MARK=m
CONFIG_NETFILTER_XT_TARGET_NFLOG=m
CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
+CONFIG_NETFILTER_XT_TARGET_NOTRACK=m
+CONFIG_NETFILTER_XT_TARGET_TEE=m
CONFIG_NETFILTER_XT_TARGET_TRACE=m
CONFIG_NETFILTER_XT_TARGET_TCPMSS=m
CONFIG_NETFILTER_XT_TARGET_TCPOPTSTRIP=m
+CONFIG_NETFILTER_XT_MATCH_ADDRTYPE=m
+CONFIG_NETFILTER_XT_MATCH_BPF=m
CONFIG_NETFILTER_XT_MATCH_CLUSTER=m
CONFIG_NETFILTER_XT_MATCH_COMMENT=m
CONFIG_NETFILTER_XT_MATCH_CONNBYTES=m
+CONFIG_NETFILTER_XT_MATCH_CONNLABEL=m
CONFIG_NETFILTER_XT_MATCH_CONNLIMIT=m
CONFIG_NETFILTER_XT_MATCH_CONNMARK=m
CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
+CONFIG_NETFILTER_XT_MATCH_DEVGROUP=m
CONFIG_NETFILTER_XT_MATCH_DSCP=m
CONFIG_NETFILTER_XT_MATCH_ESP=m
CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m
CONFIG_NETFILTER_XT_MATCH_MAC=m
CONFIG_NETFILTER_XT_MATCH_MARK=m
CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
+CONFIG_NETFILTER_XT_MATCH_NFACCT=m
+CONFIG_NETFILTER_XT_MATCH_OSF=m
CONFIG_NETFILTER_XT_MATCH_OWNER=m
CONFIG_NETFILTER_XT_MATCH_POLICY=m
CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m
CONFIG_NETFILTER_XT_MATCH_TCPMSS=m
CONFIG_NETFILTER_XT_MATCH_TIME=m
CONFIG_NETFILTER_XT_MATCH_U32=m
+CONFIG_IP_SET=m
+CONFIG_IP_SET_BITMAP_IP=m
+CONFIG_IP_SET_BITMAP_IPMAC=m
+CONFIG_IP_SET_BITMAP_PORT=m
+CONFIG_IP_SET_HASH_IP=m
+CONFIG_IP_SET_HASH_IPPORT=m
+CONFIG_IP_SET_HASH_IPPORTIP=m
+CONFIG_IP_SET_HASH_IPPORTNET=m
+CONFIG_IP_SET_HASH_NET=m
+CONFIG_IP_SET_HASH_NETPORT=m
+CONFIG_IP_SET_HASH_NETIFACE=m
+CONFIG_IP_SET_LIST_SET=m
CONFIG_NF_CONNTRACK_IPV4=m
-CONFIG_IP_NF_QUEUE=m
CONFIG_IP_NF_IPTABLES=m
-CONFIG_IP_NF_MATCH_ADDRTYPE=m
CONFIG_IP_NF_MATCH_AH=m
CONFIG_IP_NF_MATCH_ECN=m
+CONFIG_IP_NF_MATCH_RPFILTER=m
CONFIG_IP_NF_MATCH_TTL=m
CONFIG_IP_NF_FILTER=m
CONFIG_IP_NF_TARGET_REJECT=m
-CONFIG_IP_NF_TARGET_LOG=m
CONFIG_IP_NF_TARGET_ULOG=m
-CONFIG_NF_NAT=m
+CONFIG_NF_NAT_IPV4=m
CONFIG_IP_NF_TARGET_MASQUERADE=m
CONFIG_IP_NF_TARGET_NETMAP=m
CONFIG_IP_NF_TARGET_REDIRECT=m
-CONFIG_NF_NAT_SNMP_BASIC=m
CONFIG_IP_NF_MANGLE=m
CONFIG_IP_NF_TARGET_CLUSTERIP=m
CONFIG_IP_NF_TARGET_ECN=m
CONFIG_IP_NF_ARPFILTER=m
CONFIG_IP_NF_ARP_MANGLE=m
CONFIG_NF_CONNTRACK_IPV6=m
-CONFIG_IP6_NF_QUEUE=m
CONFIG_IP6_NF_IPTABLES=m
CONFIG_IP6_NF_MATCH_AH=m
CONFIG_IP6_NF_MATCH_EUI64=m
CONFIG_IP6_NF_MATCH_HL=m
CONFIG_IP6_NF_MATCH_IPV6HEADER=m
CONFIG_IP6_NF_MATCH_MH=m
+CONFIG_IP6_NF_MATCH_RPFILTER=m
CONFIG_IP6_NF_MATCH_RT=m
CONFIG_IP6_NF_TARGET_HL=m
-CONFIG_IP6_NF_TARGET_LOG=m
CONFIG_IP6_NF_FILTER=m
CONFIG_IP6_NF_TARGET_REJECT=m
CONFIG_IP6_NF_MANGLE=m
CONFIG_IP6_NF_RAW=m
+CONFIG_NF_NAT_IPV6=m
+CONFIG_IP6_NF_TARGET_MASQUERADE=m
+CONFIG_IP6_NF_TARGET_NPT=m
CONFIG_IP_DCCP=m
# CONFIG_IP_DCCP_CCID3 is not set
+CONFIG_SCTP_COOKIE_HMAC_SHA1=y
+CONFIG_RDS=m
+CONFIG_RDS_TCP=m
+CONFIG_L2TP=m
CONFIG_ATALK=m
+CONFIG_BATMAN_ADV=m
+CONFIG_BATMAN_ADV_DAT=y
+# CONFIG_WIRELESS is not set
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
# CONFIG_FIRMWARE_IN_KERNEL is not set
+# CONFIG_FW_LOADER_USER_HELPER is not set
CONFIG_CONNECTOR=m
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_CRYPTOLOOP=m
+CONFIG_BLK_DEV_DRBD=m
CONFIG_BLK_DEV_NBD=m
CONFIG_BLK_DEV_RAM=y
CONFIG_CDROM_PKTCDVD=m
CONFIG_ATA_OVER_ETH=m
CONFIG_IDE=y
+CONFIG_IDE_GD_ATAPI=y
CONFIG_BLK_DEV_IDECD=y
CONFIG_BLK_DEV_Q40IDE=y
CONFIG_RAID_ATTRS=m
CONFIG_BLK_DEV_SR_VENDOR=y
CONFIG_CHR_DEV_SG=m
CONFIG_SCSI_CONSTANTS=y
-CONFIG_SCSI_SAS_LIBSAS=m
-# CONFIG_SCSI_SAS_LIBSAS_DEBUG is not set
-CONFIG_SCSI_SRP_ATTRS=m
-CONFIG_SCSI_SRP_TGT_ATTRS=y
+CONFIG_SCSI_SAS_ATTRS=m
CONFIG_ISCSI_TCP=m
+CONFIG_ISCSI_BOOT_SYSFS=m
CONFIG_MD=y
-CONFIG_BLK_DEV_MD=m
CONFIG_MD_LINEAR=m
CONFIG_MD_RAID0=m
-CONFIG_MD_RAID1=m
-CONFIG_MD_RAID456=m
CONFIG_BLK_DEV_DM=m
CONFIG_DM_CRYPT=m
CONFIG_DM_SNAPSHOT=m
+CONFIG_DM_THIN_PROVISIONING=m
+CONFIG_DM_CACHE=m
CONFIG_DM_MIRROR=m
+CONFIG_DM_RAID=m
CONFIG_DM_ZERO=m
CONFIG_DM_MULTIPATH=m
CONFIG_DM_UEVENT=y
+CONFIG_TARGET_CORE=m
+CONFIG_TCM_IBLOCK=m
+CONFIG_TCM_FILEIO=m
+CONFIG_TCM_PSCSI=m
CONFIG_NETDEVICES=y
CONFIG_DUMMY=m
-CONFIG_MACVLAN=m
CONFIG_EQUALIZER=m
+CONFIG_NET_TEAM=m
+CONFIG_NET_TEAM_MODE_BROADCAST=m
+CONFIG_NET_TEAM_MODE_ROUNDROBIN=m
+CONFIG_NET_TEAM_MODE_ACTIVEBACKUP=m
+CONFIG_NET_TEAM_MODE_LOADBALANCE=m
+CONFIG_VXLAN=m
+CONFIG_NETCONSOLE=m
+CONFIG_NETCONSOLE_DYNAMIC=y
CONFIG_VETH=m
-CONFIG_NET_ETHERNET=y
+# CONFIG_NET_VENDOR_3COM is not set
+# CONFIG_NET_VENDOR_AMD is not set
+# CONFIG_NET_CADENCE is not set
+# CONFIG_NET_VENDOR_BROADCOM is not set
+# CONFIG_NET_VENDOR_CIRRUS is not set
+# CONFIG_NET_VENDOR_FUJITSU is not set
+# CONFIG_NET_VENDOR_HP is not set
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
CONFIG_NE2000=m
-# CONFIG_NETDEV_1000 is not set
-# CONFIG_NETDEV_10000 is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_SMSC is not set
+# CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_WIZNET is not set
CONFIG_PPP=m
-CONFIG_PPP_FILTER=y
-CONFIG_PPP_ASYNC=m
-CONFIG_PPP_SYNC_TTY=m
-CONFIG_PPP_DEFLATE=m
CONFIG_PPP_BSDCOMP=m
+CONFIG_PPP_DEFLATE=m
+CONFIG_PPP_FILTER=y
CONFIG_PPP_MPPE=m
CONFIG_PPPOE=m
+CONFIG_PPTP=m
+CONFIG_PPPOL2TP=m
+CONFIG_PPP_ASYNC=m
+CONFIG_PPP_SYNC_TTY=m
CONFIG_SLIP=m
CONFIG_SLIP_COMPRESSED=y
CONFIG_SLIP_SMART=y
CONFIG_SLIP_MODE_SLIP6=y
-CONFIG_NETCONSOLE=m
-CONFIG_NETCONSOLE_DYNAMIC=y
-CONFIG_INPUT_FF_MEMLESS=m
+# CONFIG_WLAN is not set
+CONFIG_INPUT_EVDEV=m
# CONFIG_KEYBOARD_ATKBD is not set
-CONFIG_MOUSE_PS2=m
+# CONFIG_MOUSE_PS2 is not set
CONFIG_MOUSE_SERIAL=m
CONFIG_INPUT_MISC=y
CONFIG_INPUT_M68K_BEEP=m
-CONFIG_SERIO=m
-# CONFIG_SERIO_SERPORT is not set
-CONFIG_SERIO_Q40KBD=m
+CONFIG_SERIO_Q40KBD=y
CONFIG_VT_HW_CONSOLE_BINDING=y
+# CONFIG_LEGACY_PTYS is not set
# CONFIG_DEVKMEM is not set
# CONFIG_HW_RANDOM is not set
-CONFIG_GEN_RTC=m
-CONFIG_GEN_RTC_X=y
+CONFIG_NTP_PPS=y
+CONFIG_PPS_CLIENT_LDISC=m
+CONFIG_PTP_1588_CLOCK=m
# CONFIG_HWMON is not set
CONFIG_FB=y
CONFIG_FRAMEBUFFER_CONSOLE=y
CONFIG_DMASOUND_Q40=m
CONFIG_HID=m
CONFIG_HIDRAW=y
+CONFIG_UHID=m
+# CONFIG_HID_GENERIC is not set
# CONFIG_USB_SUPPORT is not set
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_GENERIC=m
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_HEARTBEAT=y
+CONFIG_PROC_HARDWARE=y
CONFIG_EXT2_FS=y
CONFIG_EXT3_FS=y
# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
# CONFIG_EXT3_FS_XATTR is not set
+CONFIG_EXT4_FS=y
CONFIG_REISERFS_FS=m
CONFIG_JFS_FS=m
CONFIG_XFS_FS=m
CONFIG_OCFS2_FS=m
-# CONFIG_OCFS2_FS_STATS is not set
# CONFIG_OCFS2_DEBUG_MASKLOG is not set
+CONFIG_FANOTIFY=y
CONFIG_QUOTA_NETLINK_INTERFACE=y
# CONFIG_PRINT_QUOTA_WARNING is not set
-CONFIG_AUTOFS_FS=m
CONFIG_AUTOFS4_FS=m
CONFIG_FUSE_FS=m
+CONFIG_CUSE=m
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
CONFIG_UDF_FS=m
-CONFIG_MSDOS_FS=y
+CONFIG_MSDOS_FS=m
CONFIG_VFAT_FS=m
CONFIG_PROC_KCORE=y
CONFIG_TMPFS=y
CONFIG_AFFS_FS=m
+CONFIG_ECRYPT_FS=m
+CONFIG_ECRYPT_FS_MESSAGING=y
CONFIG_HFS_FS=m
CONFIG_HFSPLUS_FS=m
CONFIG_CRAMFS=m
CONFIG_SQUASHFS=m
-CONFIG_MINIX_FS=y
+CONFIG_SQUASHFS_LZO=y
+CONFIG_MINIX_FS=m
+CONFIG_OMFS_FS=m
CONFIG_HPFS_FS=m
+CONFIG_QNX4FS_FS=m
+CONFIG_QNX6FS_FS=m
CONFIG_SYSV_FS=m
CONFIG_UFS_FS=m
CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
CONFIG_NFS_V4=y
+CONFIG_NFS_SWAP=y
+CONFIG_ROOT_NFS=y
CONFIG_NFSD=m
CONFIG_NFSD_V3=y
-CONFIG_SMB_FS=m
-CONFIG_SMB_NLS_DEFAULT=y
+CONFIG_CIFS=m
+# CONFIG_CIFS_DEBUG is not set
CONFIG_CODA_FS=m
CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_CODEPAGE_737=m
CONFIG_NLS_ISO8859_15=m
CONFIG_NLS_KOI8_R=m
CONFIG_NLS_KOI8_U=m
+CONFIG_NLS_MAC_ROMAN=m
+CONFIG_NLS_MAC_CELTIC=m
+CONFIG_NLS_MAC_CENTEURO=m
+CONFIG_NLS_MAC_CROATIAN=m
+CONFIG_NLS_MAC_CYRILLIC=m
+CONFIG_NLS_MAC_GAELIC=m
+CONFIG_NLS_MAC_GREEK=m
+CONFIG_NLS_MAC_ICELAND=m
+CONFIG_NLS_MAC_INUIT=m
+CONFIG_NLS_MAC_ROMANIAN=m
+CONFIG_NLS_MAC_TURKISH=m
CONFIG_DLM=m
CONFIG_MAGIC_SYSRQ=y
-# CONFIG_RCU_CPU_STALL_DETECTOR is not set
-CONFIG_SYSCTL_SYSCALL_CHECK=y
+CONFIG_ASYNC_RAID6_TEST=m
+CONFIG_ENCRYPTED_KEYS=m
+CONFIG_CRYPTO_MANAGER=y
+CONFIG_CRYPTO_USER=m
CONFIG_CRYPTO_NULL=m
CONFIG_CRYPTO_CRYPTD=m
CONFIG_CRYPTO_TEST=m
CONFIG_CRYPTO_LRW=m
CONFIG_CRYPTO_PCBC=m
CONFIG_CRYPTO_XTS=m
-CONFIG_CRYPTO_HMAC=y
CONFIG_CRYPTO_XCBC=m
-CONFIG_CRYPTO_MD4=m
+CONFIG_CRYPTO_VMAC=m
CONFIG_CRYPTO_MICHAEL_MIC=m
CONFIG_CRYPTO_RMD128=m
CONFIG_CRYPTO_RMD160=m
CONFIG_CRYPTO_RMD256=m
CONFIG_CRYPTO_RMD320=m
-CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
CONFIG_CRYPTO_TGR192=m
CONFIG_CRYPTO_WP512=m
-CONFIG_CRYPTO_AES=m
CONFIG_CRYPTO_ANUBIS=m
CONFIG_CRYPTO_BLOWFISH=m
CONFIG_CRYPTO_CAMELLIA=m
CONFIG_CRYPTO_ZLIB=m
CONFIG_CRYPTO_LZO=m
# CONFIG_CRYPTO_ANSI_CPRNG is not set
+CONFIG_CRYPTO_USER_API_HASH=m
+CONFIG_CRYPTO_USER_API_SKCIPHER=m
# CONFIG_CRYPTO_HW is not set
-CONFIG_CRC16=m
CONFIG_CRC_T10DIF=y
+CONFIG_XZ_DEC_X86=y
+CONFIG_XZ_DEC_POWERPC=y
+CONFIG_XZ_DEC_IA64=y
+CONFIG_XZ_DEC_ARM=y
+CONFIG_XZ_DEC_ARMTHUMB=y
+CONFIG_XZ_DEC_SPARC=y
+CONFIG_XZ_DEC_TEST=m
-CONFIG_EXPERIMENTAL=y
CONFIG_LOCALVERSION="-sun3"
CONFIG_SYSVIPC=y
CONFIG_POSIX_MQUEUE=y
+CONFIG_FHANDLE=y
CONFIG_BSD_PROCESS_ACCT=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_RELAY=y
+CONFIG_BSD_PROCESS_ACCT_V3=y
+CONFIG_LOG_BUF_SHIFT=16
+# CONFIG_UTS_NS is not set
+# CONFIG_IPC_NS is not set
+# CONFIG_PID_NS is not set
+# CONFIG_NET_NS is not set
CONFIG_BLK_DEV_INITRD=y
-# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_SLAB=y
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_AMIGA_PARTITION=y
+CONFIG_ATARI_PARTITION=y
+CONFIG_MAC_PARTITION=y
+CONFIG_BSD_DISKLABEL=y
+CONFIG_MINIX_SUBPARTITION=y
+CONFIG_SOLARIS_X86_PARTITION=y
+CONFIG_UNIXWARE_DISKLABEL=y
+# CONFIG_EFI_PARTITION is not set
+CONFIG_SYSV68_PARTITION=y
+CONFIG_IOSCHED_DEADLINE=m
CONFIG_SUN3=y
+# CONFIG_COMPACTION is not set
+CONFIG_CLEANCACHE=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
CONFIG_BINFMT_AOUT=m
CONFIG_BINFMT_MISC=m
-CONFIG_PROC_HARDWARE=y
CONFIG_NET=y
CONFIG_PACKET=y
+CONFIG_PACKET_DIAG=m
CONFIG_UNIX=y
+CONFIG_UNIX_DIAG=m
+CONFIG_XFRM_MIGRATE=y
CONFIG_NET_KEY=y
-CONFIG_NET_KEY_MIGRATE=y
CONFIG_INET=y
CONFIG_IP_PNP=y
CONFIG_IP_PNP_DHCP=y
CONFIG_IP_PNP_BOOTP=y
CONFIG_IP_PNP_RARP=y
CONFIG_NET_IPIP=m
+CONFIG_NET_IPGRE_DEMUX=m
CONFIG_NET_IPGRE=m
CONFIG_SYN_COOKIES=y
+CONFIG_NET_IPVTI=m
CONFIG_INET_AH=m
CONFIG_INET_ESP=m
CONFIG_INET_IPCOMP=m
CONFIG_INET_XFRM_MODE_TRANSPORT=m
CONFIG_INET_XFRM_MODE_TUNNEL=m
CONFIG_INET_XFRM_MODE_BEET=m
+# CONFIG_INET_LRO is not set
CONFIG_INET_DIAG=m
+CONFIG_INET_UDP_DIAG=m
CONFIG_IPV6_PRIVACY=y
CONFIG_IPV6_ROUTER_PREF=y
-CONFIG_IPV6_ROUTE_INFO=y
CONFIG_INET6_AH=m
CONFIG_INET6_ESP=m
CONFIG_INET6_IPCOMP=m
-CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION=m
-CONFIG_IPV6_TUNNEL=m
+CONFIG_IPV6_GRE=m
CONFIG_NETFILTER=y
-CONFIG_NETFILTER_NETLINK_QUEUE=m
CONFIG_NF_CONNTRACK=m
+CONFIG_NF_CONNTRACK_ZONES=y
+# CONFIG_NF_CONNTRACK_PROCFS is not set
# CONFIG_NF_CT_PROTO_DCCP is not set
CONFIG_NF_CT_PROTO_UDPLITE=m
CONFIG_NF_CONNTRACK_AMANDA=m
CONFIG_NF_CONNTRACK_H323=m
CONFIG_NF_CONNTRACK_IRC=m
CONFIG_NF_CONNTRACK_NETBIOS_NS=m
+CONFIG_NF_CONNTRACK_SNMP=m
CONFIG_NF_CONNTRACK_PPTP=m
CONFIG_NF_CONNTRACK_SANE=m
CONFIG_NF_CONNTRACK_SIP=m
CONFIG_NF_CONNTRACK_TFTP=m
+CONFIG_NETFILTER_XT_SET=m
+CONFIG_NETFILTER_XT_TARGET_CHECKSUM=m
CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
CONFIG_NETFILTER_XT_TARGET_CONNMARK=m
CONFIG_NETFILTER_XT_TARGET_DSCP=m
+CONFIG_NETFILTER_XT_TARGET_HMARK=m
+CONFIG_NETFILTER_XT_TARGET_IDLETIMER=m
+CONFIG_NETFILTER_XT_TARGET_LOG=m
CONFIG_NETFILTER_XT_TARGET_MARK=m
CONFIG_NETFILTER_XT_TARGET_NFLOG=m
CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
+CONFIG_NETFILTER_XT_TARGET_NOTRACK=m
+CONFIG_NETFILTER_XT_TARGET_TEE=m
CONFIG_NETFILTER_XT_TARGET_TRACE=m
CONFIG_NETFILTER_XT_TARGET_TCPMSS=m
CONFIG_NETFILTER_XT_TARGET_TCPOPTSTRIP=m
+CONFIG_NETFILTER_XT_MATCH_ADDRTYPE=m
+CONFIG_NETFILTER_XT_MATCH_BPF=m
CONFIG_NETFILTER_XT_MATCH_CLUSTER=m
CONFIG_NETFILTER_XT_MATCH_COMMENT=m
CONFIG_NETFILTER_XT_MATCH_CONNBYTES=m
+CONFIG_NETFILTER_XT_MATCH_CONNLABEL=m
CONFIG_NETFILTER_XT_MATCH_CONNLIMIT=m
CONFIG_NETFILTER_XT_MATCH_CONNMARK=m
CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
+CONFIG_NETFILTER_XT_MATCH_DEVGROUP=m
CONFIG_NETFILTER_XT_MATCH_DSCP=m
CONFIG_NETFILTER_XT_MATCH_ESP=m
CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m
CONFIG_NETFILTER_XT_MATCH_MAC=m
CONFIG_NETFILTER_XT_MATCH_MARK=m
CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
+CONFIG_NETFILTER_XT_MATCH_NFACCT=m
+CONFIG_NETFILTER_XT_MATCH_OSF=m
CONFIG_NETFILTER_XT_MATCH_OWNER=m
CONFIG_NETFILTER_XT_MATCH_POLICY=m
CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m
CONFIG_NETFILTER_XT_MATCH_TCPMSS=m
CONFIG_NETFILTER_XT_MATCH_TIME=m
CONFIG_NETFILTER_XT_MATCH_U32=m
+CONFIG_IP_SET=m
+CONFIG_IP_SET_BITMAP_IP=m
+CONFIG_IP_SET_BITMAP_IPMAC=m
+CONFIG_IP_SET_BITMAP_PORT=m
+CONFIG_IP_SET_HASH_IP=m
+CONFIG_IP_SET_HASH_IPPORT=m
+CONFIG_IP_SET_HASH_IPPORTIP=m
+CONFIG_IP_SET_HASH_IPPORTNET=m
+CONFIG_IP_SET_HASH_NET=m
+CONFIG_IP_SET_HASH_NETPORT=m
+CONFIG_IP_SET_HASH_NETIFACE=m
+CONFIG_IP_SET_LIST_SET=m
CONFIG_NF_CONNTRACK_IPV4=m
-CONFIG_IP_NF_QUEUE=m
CONFIG_IP_NF_IPTABLES=m
-CONFIG_IP_NF_MATCH_ADDRTYPE=m
CONFIG_IP_NF_MATCH_AH=m
CONFIG_IP_NF_MATCH_ECN=m
+CONFIG_IP_NF_MATCH_RPFILTER=m
CONFIG_IP_NF_MATCH_TTL=m
CONFIG_IP_NF_FILTER=m
CONFIG_IP_NF_TARGET_REJECT=m
-CONFIG_IP_NF_TARGET_LOG=m
CONFIG_IP_NF_TARGET_ULOG=m
-CONFIG_NF_NAT=m
+CONFIG_NF_NAT_IPV4=m
CONFIG_IP_NF_TARGET_MASQUERADE=m
CONFIG_IP_NF_TARGET_NETMAP=m
CONFIG_IP_NF_TARGET_REDIRECT=m
-CONFIG_NF_NAT_SNMP_BASIC=m
CONFIG_IP_NF_MANGLE=m
CONFIG_IP_NF_TARGET_CLUSTERIP=m
CONFIG_IP_NF_TARGET_ECN=m
CONFIG_IP_NF_ARPFILTER=m
CONFIG_IP_NF_ARP_MANGLE=m
CONFIG_NF_CONNTRACK_IPV6=m
-CONFIG_IP6_NF_QUEUE=m
CONFIG_IP6_NF_IPTABLES=m
CONFIG_IP6_NF_MATCH_AH=m
CONFIG_IP6_NF_MATCH_EUI64=m
CONFIG_IP6_NF_MATCH_HL=m
CONFIG_IP6_NF_MATCH_IPV6HEADER=m
CONFIG_IP6_NF_MATCH_MH=m
+CONFIG_IP6_NF_MATCH_RPFILTER=m
CONFIG_IP6_NF_MATCH_RT=m
CONFIG_IP6_NF_TARGET_HL=m
-CONFIG_IP6_NF_TARGET_LOG=m
CONFIG_IP6_NF_FILTER=m
CONFIG_IP6_NF_TARGET_REJECT=m
CONFIG_IP6_NF_MANGLE=m
CONFIG_IP6_NF_RAW=m
+CONFIG_NF_NAT_IPV6=m
+CONFIG_IP6_NF_TARGET_MASQUERADE=m
+CONFIG_IP6_NF_TARGET_NPT=m
CONFIG_IP_DCCP=m
# CONFIG_IP_DCCP_CCID3 is not set
+CONFIG_SCTP_COOKIE_HMAC_SHA1=y
+CONFIG_RDS=m
+CONFIG_RDS_TCP=m
+CONFIG_L2TP=m
CONFIG_ATALK=m
+CONFIG_BATMAN_ADV=m
+CONFIG_BATMAN_ADV_DAT=y
+# CONFIG_WIRELESS is not set
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
# CONFIG_FIRMWARE_IN_KERNEL is not set
+# CONFIG_FW_LOADER_USER_HELPER is not set
CONFIG_CONNECTOR=m
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_CRYPTOLOOP=m
+CONFIG_BLK_DEV_DRBD=m
CONFIG_BLK_DEV_NBD=m
CONFIG_BLK_DEV_RAM=y
CONFIG_CDROM_PKTCDVD=m
CONFIG_BLK_DEV_SR_VENDOR=y
CONFIG_CHR_DEV_SG=m
CONFIG_SCSI_CONSTANTS=y
-CONFIG_SCSI_SAS_LIBSAS=m
-# CONFIG_SCSI_SAS_LIBSAS_DEBUG is not set
-CONFIG_SCSI_SRP_ATTRS=m
-CONFIG_SCSI_SRP_TGT_ATTRS=y
+CONFIG_SCSI_SAS_ATTRS=m
CONFIG_ISCSI_TCP=m
+CONFIG_ISCSI_BOOT_SYSFS=m
CONFIG_SUN3_SCSI=y
CONFIG_MD=y
-CONFIG_BLK_DEV_MD=m
CONFIG_MD_LINEAR=m
CONFIG_MD_RAID0=m
-CONFIG_MD_RAID1=m
-CONFIG_MD_RAID456=m
CONFIG_BLK_DEV_DM=m
CONFIG_DM_CRYPT=m
CONFIG_DM_SNAPSHOT=m
+CONFIG_DM_THIN_PROVISIONING=m
+CONFIG_DM_CACHE=m
CONFIG_DM_MIRROR=m
+CONFIG_DM_RAID=m
CONFIG_DM_ZERO=m
CONFIG_DM_MULTIPATH=m
CONFIG_DM_UEVENT=y
+CONFIG_TARGET_CORE=m
+CONFIG_TCM_IBLOCK=m
+CONFIG_TCM_FILEIO=m
+CONFIG_TCM_PSCSI=m
CONFIG_NETDEVICES=y
CONFIG_DUMMY=m
-CONFIG_MACVLAN=m
CONFIG_EQUALIZER=m
+CONFIG_NET_TEAM=m
+CONFIG_NET_TEAM_MODE_BROADCAST=m
+CONFIG_NET_TEAM_MODE_ROUNDROBIN=m
+CONFIG_NET_TEAM_MODE_ACTIVEBACKUP=m
+CONFIG_NET_TEAM_MODE_LOADBALANCE=m
+CONFIG_VXLAN=m
+CONFIG_NETCONSOLE=m
+CONFIG_NETCONSOLE_DYNAMIC=y
CONFIG_VETH=m
-CONFIG_NET_ETHERNET=y
CONFIG_SUN3LANCE=y
+# CONFIG_NET_CADENCE is not set
CONFIG_SUN3_82586=y
-# CONFIG_NETDEV_1000 is not set
-# CONFIG_NETDEV_10000 is not set
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_SUN is not set
+# CONFIG_NET_VENDOR_WIZNET is not set
CONFIG_PPP=m
-CONFIG_PPP_FILTER=y
-CONFIG_PPP_ASYNC=m
-CONFIG_PPP_SYNC_TTY=m
-CONFIG_PPP_DEFLATE=m
CONFIG_PPP_BSDCOMP=m
+CONFIG_PPP_DEFLATE=m
+CONFIG_PPP_FILTER=y
CONFIG_PPP_MPPE=m
CONFIG_PPPOE=m
+CONFIG_PPTP=m
+CONFIG_PPPOL2TP=m
+CONFIG_PPP_ASYNC=m
+CONFIG_PPP_SYNC_TTY=m
CONFIG_SLIP=m
CONFIG_SLIP_COMPRESSED=y
CONFIG_SLIP_SMART=y
CONFIG_SLIP_MODE_SLIP6=y
-CONFIG_NETCONSOLE=m
-CONFIG_NETCONSOLE_DYNAMIC=y
-CONFIG_INPUT_FF_MEMLESS=m
+# CONFIG_WLAN is not set
+CONFIG_INPUT_EVDEV=m
# CONFIG_KEYBOARD_ATKBD is not set
CONFIG_KEYBOARD_SUNKBD=y
-CONFIG_MOUSE_PS2=m
+# CONFIG_MOUSE_PS2 is not set
CONFIG_MOUSE_SERIAL=m
-# CONFIG_SERIO_SERPORT is not set
CONFIG_VT_HW_CONSOLE_BINDING=y
+# CONFIG_LEGACY_PTYS is not set
# CONFIG_DEVKMEM is not set
# CONFIG_HW_RANDOM is not set
-CONFIG_GEN_RTC=m
-CONFIG_GEN_RTC_X=y
+CONFIG_NTP_PPS=y
+CONFIG_PPS_CLIENT_LDISC=m
+CONFIG_PTP_1588_CLOCK=m
# CONFIG_HWMON is not set
CONFIG_FB=y
CONFIG_FRAMEBUFFER_CONSOLE=y
CONFIG_LOGO=y
CONFIG_HID=m
CONFIG_HIDRAW=y
+CONFIG_UHID=m
+# CONFIG_HID_GENERIC is not set
# CONFIG_USB_SUPPORT is not set
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_GENERIC=m
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_PROC_HARDWARE=y
CONFIG_EXT2_FS=y
CONFIG_EXT3_FS=y
# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
# CONFIG_EXT3_FS_XATTR is not set
+CONFIG_EXT4_FS=y
CONFIG_REISERFS_FS=m
CONFIG_JFS_FS=m
CONFIG_XFS_FS=m
CONFIG_OCFS2_FS=m
-# CONFIG_OCFS2_FS_STATS is not set
# CONFIG_OCFS2_DEBUG_MASKLOG is not set
+CONFIG_FANOTIFY=y
CONFIG_QUOTA_NETLINK_INTERFACE=y
# CONFIG_PRINT_QUOTA_WARNING is not set
-CONFIG_AUTOFS_FS=m
CONFIG_AUTOFS4_FS=m
CONFIG_FUSE_FS=m
+CONFIG_CUSE=m
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
CONFIG_UDF_FS=m
-CONFIG_MSDOS_FS=y
+CONFIG_MSDOS_FS=m
CONFIG_VFAT_FS=m
CONFIG_PROC_KCORE=y
CONFIG_TMPFS=y
CONFIG_AFFS_FS=m
+CONFIG_ECRYPT_FS=m
+CONFIG_ECRYPT_FS_MESSAGING=y
CONFIG_HFS_FS=m
CONFIG_HFSPLUS_FS=m
CONFIG_CRAMFS=m
CONFIG_SQUASHFS=m
-CONFIG_MINIX_FS=y
+CONFIG_SQUASHFS_LZO=y
+CONFIG_MINIX_FS=m
+CONFIG_OMFS_FS=m
CONFIG_HPFS_FS=m
+CONFIG_QNX4FS_FS=m
+CONFIG_QNX6FS_FS=m
CONFIG_SYSV_FS=m
CONFIG_UFS_FS=m
CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
CONFIG_NFS_V4=y
+CONFIG_NFS_SWAP=y
CONFIG_ROOT_NFS=y
CONFIG_NFSD=m
CONFIG_NFSD_V3=y
-CONFIG_SMB_FS=m
-CONFIG_SMB_NLS_DEFAULT=y
+CONFIG_CIFS=m
+# CONFIG_CIFS_DEBUG is not set
CONFIG_CODA_FS=m
CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_CODEPAGE_737=m
CONFIG_NLS_ISO8859_15=m
CONFIG_NLS_KOI8_R=m
CONFIG_NLS_KOI8_U=m
+CONFIG_NLS_MAC_ROMAN=m
+CONFIG_NLS_MAC_CELTIC=m
+CONFIG_NLS_MAC_CENTEURO=m
+CONFIG_NLS_MAC_CROATIAN=m
+CONFIG_NLS_MAC_CYRILLIC=m
+CONFIG_NLS_MAC_GAELIC=m
+CONFIG_NLS_MAC_GREEK=m
+CONFIG_NLS_MAC_ICELAND=m
+CONFIG_NLS_MAC_INUIT=m
+CONFIG_NLS_MAC_ROMANIAN=m
+CONFIG_NLS_MAC_TURKISH=m
CONFIG_DLM=m
CONFIG_MAGIC_SYSRQ=y
-# CONFIG_RCU_CPU_STALL_DETECTOR is not set
-CONFIG_SYSCTL_SYSCALL_CHECK=y
+CONFIG_ASYNC_RAID6_TEST=m
+CONFIG_ENCRYPTED_KEYS=m
+CONFIG_CRYPTO_MANAGER=y
+CONFIG_CRYPTO_USER=m
CONFIG_CRYPTO_NULL=m
CONFIG_CRYPTO_CRYPTD=m
CONFIG_CRYPTO_TEST=m
CONFIG_CRYPTO_LRW=m
CONFIG_CRYPTO_PCBC=m
CONFIG_CRYPTO_XTS=m
-CONFIG_CRYPTO_HMAC=y
CONFIG_CRYPTO_XCBC=m
-CONFIG_CRYPTO_MD4=m
+CONFIG_CRYPTO_VMAC=m
CONFIG_CRYPTO_MICHAEL_MIC=m
CONFIG_CRYPTO_RMD128=m
CONFIG_CRYPTO_RMD160=m
CONFIG_CRYPTO_RMD256=m
CONFIG_CRYPTO_RMD320=m
-CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
CONFIG_CRYPTO_TGR192=m
CONFIG_CRYPTO_WP512=m
-CONFIG_CRYPTO_AES=m
CONFIG_CRYPTO_ANUBIS=m
CONFIG_CRYPTO_BLOWFISH=m
CONFIG_CRYPTO_CAMELLIA=m
CONFIG_CRYPTO_ZLIB=m
CONFIG_CRYPTO_LZO=m
# CONFIG_CRYPTO_ANSI_CPRNG is not set
+CONFIG_CRYPTO_USER_API_HASH=m
+CONFIG_CRYPTO_USER_API_SKCIPHER=m
# CONFIG_CRYPTO_HW is not set
-CONFIG_CRC16=m
CONFIG_CRC_T10DIF=y
+CONFIG_XZ_DEC_X86=y
+CONFIG_XZ_DEC_POWERPC=y
+CONFIG_XZ_DEC_IA64=y
+CONFIG_XZ_DEC_ARM=y
+CONFIG_XZ_DEC_ARMTHUMB=y
+CONFIG_XZ_DEC_SPARC=y
+CONFIG_XZ_DEC_TEST=m
-CONFIG_EXPERIMENTAL=y
CONFIG_LOCALVERSION="-sun3x"
CONFIG_SYSVIPC=y
CONFIG_POSIX_MQUEUE=y
+CONFIG_FHANDLE=y
CONFIG_BSD_PROCESS_ACCT=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_RELAY=y
+CONFIG_BSD_PROCESS_ACCT_V3=y
+CONFIG_LOG_BUF_SHIFT=16
+# CONFIG_UTS_NS is not set
+# CONFIG_IPC_NS is not set
+# CONFIG_PID_NS is not set
+# CONFIG_NET_NS is not set
CONFIG_BLK_DEV_INITRD=y
-# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_SLAB=y
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_AMIGA_PARTITION=y
+CONFIG_ATARI_PARTITION=y
+CONFIG_MAC_PARTITION=y
+CONFIG_BSD_DISKLABEL=y
+CONFIG_MINIX_SUBPARTITION=y
+CONFIG_SOLARIS_X86_PARTITION=y
+CONFIG_UNIXWARE_DISKLABEL=y
+# CONFIG_EFI_PARTITION is not set
+CONFIG_SYSV68_PARTITION=y
+CONFIG_IOSCHED_DEADLINE=m
CONFIG_SUN3X=y
+# CONFIG_COMPACTION is not set
+CONFIG_CLEANCACHE=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
CONFIG_BINFMT_AOUT=m
CONFIG_BINFMT_MISC=m
-CONFIG_PROC_HARDWARE=y
CONFIG_NET=y
CONFIG_PACKET=y
+CONFIG_PACKET_DIAG=m
CONFIG_UNIX=y
+CONFIG_UNIX_DIAG=m
+CONFIG_XFRM_MIGRATE=y
CONFIG_NET_KEY=y
-CONFIG_NET_KEY_MIGRATE=y
CONFIG_INET=y
CONFIG_IP_PNP=y
CONFIG_IP_PNP_DHCP=y
CONFIG_IP_PNP_BOOTP=y
CONFIG_IP_PNP_RARP=y
CONFIG_NET_IPIP=m
+CONFIG_NET_IPGRE_DEMUX=m
CONFIG_NET_IPGRE=m
CONFIG_SYN_COOKIES=y
+CONFIG_NET_IPVTI=m
CONFIG_INET_AH=m
CONFIG_INET_ESP=m
CONFIG_INET_IPCOMP=m
CONFIG_INET_XFRM_MODE_TRANSPORT=m
CONFIG_INET_XFRM_MODE_TUNNEL=m
CONFIG_INET_XFRM_MODE_BEET=m
+# CONFIG_INET_LRO is not set
CONFIG_INET_DIAG=m
+CONFIG_INET_UDP_DIAG=m
CONFIG_IPV6_PRIVACY=y
CONFIG_IPV6_ROUTER_PREF=y
-CONFIG_IPV6_ROUTE_INFO=y
CONFIG_INET6_AH=m
CONFIG_INET6_ESP=m
CONFIG_INET6_IPCOMP=m
-CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION=m
-CONFIG_IPV6_TUNNEL=m
+CONFIG_IPV6_GRE=m
CONFIG_NETFILTER=y
-CONFIG_NETFILTER_NETLINK_QUEUE=m
CONFIG_NF_CONNTRACK=m
+CONFIG_NF_CONNTRACK_ZONES=y
+# CONFIG_NF_CONNTRACK_PROCFS is not set
# CONFIG_NF_CT_PROTO_DCCP is not set
CONFIG_NF_CT_PROTO_UDPLITE=m
CONFIG_NF_CONNTRACK_AMANDA=m
CONFIG_NF_CONNTRACK_H323=m
CONFIG_NF_CONNTRACK_IRC=m
CONFIG_NF_CONNTRACK_NETBIOS_NS=m
+CONFIG_NF_CONNTRACK_SNMP=m
CONFIG_NF_CONNTRACK_PPTP=m
CONFIG_NF_CONNTRACK_SANE=m
CONFIG_NF_CONNTRACK_SIP=m
CONFIG_NF_CONNTRACK_TFTP=m
+CONFIG_NETFILTER_XT_SET=m
+CONFIG_NETFILTER_XT_TARGET_CHECKSUM=m
CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
CONFIG_NETFILTER_XT_TARGET_CONNMARK=m
CONFIG_NETFILTER_XT_TARGET_DSCP=m
+CONFIG_NETFILTER_XT_TARGET_HMARK=m
+CONFIG_NETFILTER_XT_TARGET_IDLETIMER=m
+CONFIG_NETFILTER_XT_TARGET_LOG=m
CONFIG_NETFILTER_XT_TARGET_MARK=m
CONFIG_NETFILTER_XT_TARGET_NFLOG=m
CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
+CONFIG_NETFILTER_XT_TARGET_NOTRACK=m
+CONFIG_NETFILTER_XT_TARGET_TEE=m
CONFIG_NETFILTER_XT_TARGET_TRACE=m
CONFIG_NETFILTER_XT_TARGET_TCPMSS=m
CONFIG_NETFILTER_XT_TARGET_TCPOPTSTRIP=m
+CONFIG_NETFILTER_XT_MATCH_ADDRTYPE=m
+CONFIG_NETFILTER_XT_MATCH_BPF=m
CONFIG_NETFILTER_XT_MATCH_CLUSTER=m
CONFIG_NETFILTER_XT_MATCH_COMMENT=m
CONFIG_NETFILTER_XT_MATCH_CONNBYTES=m
+CONFIG_NETFILTER_XT_MATCH_CONNLABEL=m
CONFIG_NETFILTER_XT_MATCH_CONNLIMIT=m
CONFIG_NETFILTER_XT_MATCH_CONNMARK=m
CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
+CONFIG_NETFILTER_XT_MATCH_DEVGROUP=m
CONFIG_NETFILTER_XT_MATCH_DSCP=m
CONFIG_NETFILTER_XT_MATCH_ESP=m
CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m
CONFIG_NETFILTER_XT_MATCH_MAC=m
CONFIG_NETFILTER_XT_MATCH_MARK=m
CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
+CONFIG_NETFILTER_XT_MATCH_NFACCT=m
+CONFIG_NETFILTER_XT_MATCH_OSF=m
CONFIG_NETFILTER_XT_MATCH_OWNER=m
CONFIG_NETFILTER_XT_MATCH_POLICY=m
CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m
CONFIG_NETFILTER_XT_MATCH_TCPMSS=m
CONFIG_NETFILTER_XT_MATCH_TIME=m
CONFIG_NETFILTER_XT_MATCH_U32=m
+CONFIG_IP_SET=m
+CONFIG_IP_SET_BITMAP_IP=m
+CONFIG_IP_SET_BITMAP_IPMAC=m
+CONFIG_IP_SET_BITMAP_PORT=m
+CONFIG_IP_SET_HASH_IP=m
+CONFIG_IP_SET_HASH_IPPORT=m
+CONFIG_IP_SET_HASH_IPPORTIP=m
+CONFIG_IP_SET_HASH_IPPORTNET=m
+CONFIG_IP_SET_HASH_NET=m
+CONFIG_IP_SET_HASH_NETPORT=m
+CONFIG_IP_SET_HASH_NETIFACE=m
+CONFIG_IP_SET_LIST_SET=m
CONFIG_NF_CONNTRACK_IPV4=m
-CONFIG_IP_NF_QUEUE=m
CONFIG_IP_NF_IPTABLES=m
-CONFIG_IP_NF_MATCH_ADDRTYPE=m
CONFIG_IP_NF_MATCH_AH=m
CONFIG_IP_NF_MATCH_ECN=m
+CONFIG_IP_NF_MATCH_RPFILTER=m
CONFIG_IP_NF_MATCH_TTL=m
CONFIG_IP_NF_FILTER=m
CONFIG_IP_NF_TARGET_REJECT=m
-CONFIG_IP_NF_TARGET_LOG=m
CONFIG_IP_NF_TARGET_ULOG=m
-CONFIG_NF_NAT=m
+CONFIG_NF_NAT_IPV4=m
CONFIG_IP_NF_TARGET_MASQUERADE=m
CONFIG_IP_NF_TARGET_NETMAP=m
CONFIG_IP_NF_TARGET_REDIRECT=m
-CONFIG_NF_NAT_SNMP_BASIC=m
CONFIG_IP_NF_MANGLE=m
CONFIG_IP_NF_TARGET_CLUSTERIP=m
CONFIG_IP_NF_TARGET_ECN=m
CONFIG_IP_NF_ARPFILTER=m
CONFIG_IP_NF_ARP_MANGLE=m
CONFIG_NF_CONNTRACK_IPV6=m
-CONFIG_IP6_NF_QUEUE=m
CONFIG_IP6_NF_IPTABLES=m
CONFIG_IP6_NF_MATCH_AH=m
CONFIG_IP6_NF_MATCH_EUI64=m
CONFIG_IP6_NF_MATCH_HL=m
CONFIG_IP6_NF_MATCH_IPV6HEADER=m
CONFIG_IP6_NF_MATCH_MH=m
+CONFIG_IP6_NF_MATCH_RPFILTER=m
CONFIG_IP6_NF_MATCH_RT=m
CONFIG_IP6_NF_TARGET_HL=m
-CONFIG_IP6_NF_TARGET_LOG=m
CONFIG_IP6_NF_FILTER=m
CONFIG_IP6_NF_TARGET_REJECT=m
CONFIG_IP6_NF_MANGLE=m
CONFIG_IP6_NF_RAW=m
+CONFIG_NF_NAT_IPV6=m
+CONFIG_IP6_NF_TARGET_MASQUERADE=m
+CONFIG_IP6_NF_TARGET_NPT=m
CONFIG_IP_DCCP=m
# CONFIG_IP_DCCP_CCID3 is not set
+CONFIG_SCTP_COOKIE_HMAC_SHA1=y
+CONFIG_RDS=m
+CONFIG_RDS_TCP=m
+CONFIG_L2TP=m
CONFIG_ATALK=m
+CONFIG_BATMAN_ADV=m
+CONFIG_BATMAN_ADV_DAT=y
+# CONFIG_WIRELESS is not set
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
# CONFIG_FIRMWARE_IN_KERNEL is not set
+# CONFIG_FW_LOADER_USER_HELPER is not set
CONFIG_CONNECTOR=m
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_CRYPTOLOOP=m
+CONFIG_BLK_DEV_DRBD=m
CONFIG_BLK_DEV_NBD=m
CONFIG_BLK_DEV_RAM=y
CONFIG_CDROM_PKTCDVD=m
CONFIG_BLK_DEV_SR_VENDOR=y
CONFIG_CHR_DEV_SG=m
CONFIG_SCSI_CONSTANTS=y
-CONFIG_SCSI_SAS_LIBSAS=m
-# CONFIG_SCSI_SAS_LIBSAS_DEBUG is not set
-CONFIG_SCSI_SRP_ATTRS=m
-CONFIG_SCSI_SRP_TGT_ATTRS=y
+CONFIG_SCSI_SAS_ATTRS=m
CONFIG_ISCSI_TCP=m
+CONFIG_ISCSI_BOOT_SYSFS=m
CONFIG_SUN3X_ESP=y
CONFIG_MD=y
-CONFIG_BLK_DEV_MD=m
CONFIG_MD_LINEAR=m
CONFIG_MD_RAID0=m
-CONFIG_MD_RAID1=m
-CONFIG_MD_RAID456=m
CONFIG_BLK_DEV_DM=m
CONFIG_DM_CRYPT=m
CONFIG_DM_SNAPSHOT=m
+CONFIG_DM_THIN_PROVISIONING=m
+CONFIG_DM_CACHE=m
CONFIG_DM_MIRROR=m
+CONFIG_DM_RAID=m
CONFIG_DM_ZERO=m
CONFIG_DM_MULTIPATH=m
CONFIG_DM_UEVENT=y
+CONFIG_TARGET_CORE=m
+CONFIG_TCM_IBLOCK=m
+CONFIG_TCM_FILEIO=m
+CONFIG_TCM_PSCSI=m
CONFIG_NETDEVICES=y
CONFIG_DUMMY=m
-CONFIG_MACVLAN=m
CONFIG_EQUALIZER=m
+CONFIG_NET_TEAM=m
+CONFIG_NET_TEAM_MODE_BROADCAST=m
+CONFIG_NET_TEAM_MODE_ROUNDROBIN=m
+CONFIG_NET_TEAM_MODE_ACTIVEBACKUP=m
+CONFIG_NET_TEAM_MODE_LOADBALANCE=m
+CONFIG_VXLAN=m
+CONFIG_NETCONSOLE=m
+CONFIG_NETCONSOLE_DYNAMIC=y
CONFIG_VETH=m
-CONFIG_NET_ETHERNET=y
CONFIG_SUN3LANCE=y
-# CONFIG_NETDEV_1000 is not set
-# CONFIG_NETDEV_10000 is not set
+# CONFIG_NET_CADENCE is not set
+# CONFIG_NET_VENDOR_BROADCOM is not set
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_WIZNET is not set
CONFIG_PPP=m
-CONFIG_PPP_FILTER=y
-CONFIG_PPP_ASYNC=m
-CONFIG_PPP_SYNC_TTY=m
-CONFIG_PPP_DEFLATE=m
CONFIG_PPP_BSDCOMP=m
+CONFIG_PPP_DEFLATE=m
+CONFIG_PPP_FILTER=y
CONFIG_PPP_MPPE=m
CONFIG_PPPOE=m
+CONFIG_PPTP=m
+CONFIG_PPPOL2TP=m
+CONFIG_PPP_ASYNC=m
+CONFIG_PPP_SYNC_TTY=m
CONFIG_SLIP=m
CONFIG_SLIP_COMPRESSED=y
CONFIG_SLIP_SMART=y
CONFIG_SLIP_MODE_SLIP6=y
-CONFIG_NETCONSOLE=m
-CONFIG_NETCONSOLE_DYNAMIC=y
-CONFIG_INPUT_FF_MEMLESS=m
+# CONFIG_WLAN is not set
+CONFIG_INPUT_EVDEV=m
# CONFIG_KEYBOARD_ATKBD is not set
CONFIG_KEYBOARD_SUNKBD=y
-CONFIG_MOUSE_PS2=m
+# CONFIG_MOUSE_PS2 is not set
CONFIG_MOUSE_SERIAL=m
-# CONFIG_SERIO_SERPORT is not set
CONFIG_VT_HW_CONSOLE_BINDING=y
+# CONFIG_LEGACY_PTYS is not set
# CONFIG_DEVKMEM is not set
# CONFIG_HW_RANDOM is not set
-CONFIG_GEN_RTC=m
-CONFIG_GEN_RTC_X=y
+CONFIG_NTP_PPS=y
+CONFIG_PPS_CLIENT_LDISC=m
+CONFIG_PTP_1588_CLOCK=m
# CONFIG_HWMON is not set
CONFIG_FB=y
CONFIG_FRAMEBUFFER_CONSOLE=y
CONFIG_LOGO=y
CONFIG_HID=m
CONFIG_HIDRAW=y
+CONFIG_UHID=m
+# CONFIG_HID_GENERIC is not set
# CONFIG_USB_SUPPORT is not set
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_GENERIC=m
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_PROC_HARDWARE=y
CONFIG_EXT2_FS=y
CONFIG_EXT3_FS=y
# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
# CONFIG_EXT3_FS_XATTR is not set
+CONFIG_EXT4_FS=y
CONFIG_REISERFS_FS=m
CONFIG_JFS_FS=m
CONFIG_XFS_FS=m
CONFIG_OCFS2_FS=m
-# CONFIG_OCFS2_FS_STATS is not set
# CONFIG_OCFS2_DEBUG_MASKLOG is not set
+CONFIG_FANOTIFY=y
CONFIG_QUOTA_NETLINK_INTERFACE=y
# CONFIG_PRINT_QUOTA_WARNING is not set
-CONFIG_AUTOFS_FS=m
CONFIG_AUTOFS4_FS=m
CONFIG_FUSE_FS=m
+CONFIG_CUSE=m
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
CONFIG_UDF_FS=m
-CONFIG_MSDOS_FS=y
+CONFIG_MSDOS_FS=m
CONFIG_VFAT_FS=m
CONFIG_PROC_KCORE=y
CONFIG_TMPFS=y
CONFIG_AFFS_FS=m
+CONFIG_ECRYPT_FS=m
+CONFIG_ECRYPT_FS_MESSAGING=y
CONFIG_HFS_FS=m
CONFIG_HFSPLUS_FS=m
CONFIG_CRAMFS=m
CONFIG_SQUASHFS=m
-CONFIG_MINIX_FS=y
+CONFIG_SQUASHFS_LZO=y
+CONFIG_MINIX_FS=m
+CONFIG_OMFS_FS=m
CONFIG_HPFS_FS=m
+CONFIG_QNX4FS_FS=m
+CONFIG_QNX6FS_FS=m
CONFIG_SYSV_FS=m
CONFIG_UFS_FS=m
CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
CONFIG_NFS_V4=y
+CONFIG_NFS_SWAP=y
CONFIG_ROOT_NFS=y
CONFIG_NFSD=m
CONFIG_NFSD_V3=y
-CONFIG_SMB_FS=m
-CONFIG_SMB_NLS_DEFAULT=y
+CONFIG_CIFS=m
+# CONFIG_CIFS_DEBUG is not set
CONFIG_CODA_FS=m
CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_CODEPAGE_737=m
CONFIG_NLS_ISO8859_15=m
CONFIG_NLS_KOI8_R=m
CONFIG_NLS_KOI8_U=m
+CONFIG_NLS_MAC_ROMAN=m
+CONFIG_NLS_MAC_CELTIC=m
+CONFIG_NLS_MAC_CENTEURO=m
+CONFIG_NLS_MAC_CROATIAN=m
+CONFIG_NLS_MAC_CYRILLIC=m
+CONFIG_NLS_MAC_GAELIC=m
+CONFIG_NLS_MAC_GREEK=m
+CONFIG_NLS_MAC_ICELAND=m
+CONFIG_NLS_MAC_INUIT=m
+CONFIG_NLS_MAC_ROMANIAN=m
+CONFIG_NLS_MAC_TURKISH=m
CONFIG_DLM=m
CONFIG_MAGIC_SYSRQ=y
-# CONFIG_RCU_CPU_STALL_DETECTOR is not set
-CONFIG_SYSCTL_SYSCALL_CHECK=y
+CONFIG_ASYNC_RAID6_TEST=m
+CONFIG_ENCRYPTED_KEYS=m
+CONFIG_CRYPTO_MANAGER=y
+CONFIG_CRYPTO_USER=m
CONFIG_CRYPTO_NULL=m
CONFIG_CRYPTO_CRYPTD=m
CONFIG_CRYPTO_TEST=m
CONFIG_CRYPTO_LRW=m
CONFIG_CRYPTO_PCBC=m
CONFIG_CRYPTO_XTS=m
-CONFIG_CRYPTO_HMAC=y
CONFIG_CRYPTO_XCBC=m
-CONFIG_CRYPTO_MD4=m
+CONFIG_CRYPTO_VMAC=m
CONFIG_CRYPTO_MICHAEL_MIC=m
CONFIG_CRYPTO_RMD128=m
CONFIG_CRYPTO_RMD160=m
CONFIG_CRYPTO_RMD256=m
CONFIG_CRYPTO_RMD320=m
-CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
CONFIG_CRYPTO_TGR192=m
CONFIG_CRYPTO_WP512=m
-CONFIG_CRYPTO_AES=m
CONFIG_CRYPTO_ANUBIS=m
CONFIG_CRYPTO_BLOWFISH=m
CONFIG_CRYPTO_CAMELLIA=m
CONFIG_CRYPTO_ZLIB=m
CONFIG_CRYPTO_LZO=m
# CONFIG_CRYPTO_ANSI_CPRNG is not set
+CONFIG_CRYPTO_USER_API_HASH=m
+CONFIG_CRYPTO_USER_API_SKCIPHER=m
# CONFIG_CRYPTO_HW is not set
-CONFIG_CRC16=m
CONFIG_CRC_T10DIF=y
+CONFIG_XZ_DEC_X86=y
+CONFIG_XZ_DEC_POWERPC=y
+CONFIG_XZ_DEC_IA64=y
+CONFIG_XZ_DEC_ARM=y
+CONFIG_XZ_DEC_ARMTHUMB=y
+CONFIG_XZ_DEC_SPARC=y
+CONFIG_XZ_DEC_TEST=m
generic-y += emergency-restart.h
generic-y += errno.h
generic-y += exec.h
-generic-y += futex.h
generic-y += hw_irq.h
generic-y += ioctl.h
generic-y += ipcbuf.h
--- /dev/null
+#ifndef _ASM_M68K_FUTEX_H
+#define _ASM_M68K_FUTEX_H
+
+#ifdef __KERNEL__
+#if !defined(CONFIG_MMU)
+#include <asm-generic/futex.h>
+#else /* CONFIG_MMU */
+
+#include <linux/futex.h>
+#include <linux/uaccess.h>
+#include <asm/errno.h>
+
+static inline int
+futex_atomic_cmpxchg_inatomic(u32 *uval, u32 __user *uaddr,
+ u32 oldval, u32 newval)
+{
+ u32 val;
+
+ if (unlikely(get_user(val, uaddr) != 0))
+ return -EFAULT;
+
+ if (val == oldval && unlikely(put_user(newval, uaddr) != 0))
+ return -EFAULT;
+
+ *uval = val;
+
+ return 0;
+}
+
+static inline int
+futex_atomic_op_inuser(int encoded_op, u32 __user *uaddr)
+{
+ int op = (encoded_op >> 28) & 7;
+ int cmp = (encoded_op >> 24) & 15;
+ int oparg = (encoded_op << 8) >> 20;
+ int cmparg = (encoded_op << 20) >> 20;
+ int oldval, ret;
+ u32 tmp;
+
+ if (encoded_op & (FUTEX_OP_OPARG_SHIFT << 28))
+ oparg = 1 << oparg;
+
+ pagefault_disable(); /* implies preempt_disable() */
+
+ ret = -EFAULT;
+ if (unlikely(get_user(oldval, uaddr) != 0))
+ goto out_pagefault_enable;
+
+ ret = 0;
+ tmp = oldval;
+
+ switch (op) {
+ case FUTEX_OP_SET:
+ tmp = oparg;
+ break;
+ case FUTEX_OP_ADD:
+ tmp += oparg;
+ break;
+ case FUTEX_OP_OR:
+ tmp |= oparg;
+ break;
+ case FUTEX_OP_ANDN:
+ tmp &= ~oparg;
+ break;
+ case FUTEX_OP_XOR:
+ tmp ^= oparg;
+ break;
+ default:
+ ret = -ENOSYS;
+ }
+
+ if (ret == 0 && unlikely(put_user(tmp, uaddr) != 0))
+ ret = -EFAULT;
+
+out_pagefault_enable:
+ pagefault_enable(); /* subsumes preempt_enable() */
+
+ if (ret == 0) {
+ switch (cmp) {
+ case FUTEX_OP_CMP_EQ: ret = (oldval == cmparg); break;
+ case FUTEX_OP_CMP_NE: ret = (oldval != cmparg); break;
+ case FUTEX_OP_CMP_LT: ret = (oldval < cmparg); break;
+ case FUTEX_OP_CMP_GE: ret = (oldval >= cmparg); break;
+ case FUTEX_OP_CMP_LE: ret = (oldval <= cmparg); break;
+ case FUTEX_OP_CMP_GT: ret = (oldval > cmparg); break;
+ default: ret = -ENOSYS;
+ }
+ }
+ return ret;
+}
+
+#endif /* CONFIG_MMU */
+#endif /* __KERNEL__ */
+#endif /* _ASM_M68K_FUTEX_H */
return gpio < MCFGPIO_PIN_MAX ? 0 : __gpio_cansleep(gpio);
}
+#ifndef CONFIG_GPIOLIB
static inline int gpio_request_one(unsigned gpio, unsigned long flags, const char *label)
{
int err;
return err;
}
-
+#endif /* !CONFIG_GPIOLIB */
#endif
#ifdef CONFIG_MAC
L(scc_initable_mac):
- .byte 9,12 /* Reset */
.byte 4,0x44 /* x16, 1 stopbit, no parity */
.byte 3,0xc0 /* receiver: 8 bpc */
.byte 5,0xe2 /* transmitter: 8 bpc, assert dtr/rts */
- .byte 9,0 /* no interrupts */
.byte 10,0 /* NRZ */
.byte 11,0x50 /* use baud rate generator */
.byte 12,1,13,0 /* 38400 baud */
is_not_mac(L(serial_init_not_mac))
#ifdef SERIAL_DEBUG
+
/* You may define either or both of these. */
#define MAC_USE_SCC_A /* Modem port */
#define MAC_USE_SCC_B /* Printer port */
#define mac_scc_cha_b_data_offset 0x4
#define mac_scc_cha_a_data_offset 0x6
+#if defined(MAC_USE_SCC_A) || defined(MAC_USE_SCC_B)
+ movel %pc@(L(mac_sccbase)),%a0
+ /* Reset SCC device */
+ moveb #9,%a0@(mac_scc_cha_a_ctrl_offset)
+ moveb #0xc0,%a0@(mac_scc_cha_a_ctrl_offset)
+ /* Wait for 5 PCLK cycles, which is about 68 CPU cycles */
+ /* 5 / 3.6864 MHz = approx. 1.36 us = 68 / 50 MHz */
+ movel #35,%d0
+5:
+ subq #1,%d0
+ jne 5b
+#endif
+
#ifdef MAC_USE_SCC_A
/* Initialize channel A */
- movel %pc@(L(mac_sccbase)),%a0
lea %pc@(L(scc_initable_mac)),%a1
5: moveb %a1@+,%d0
jmi 6f
#ifdef MAC_USE_SCC_B
/* Initialize channel B */
-#ifndef MAC_USE_SCC_A /* Load mac_sccbase only if needed */
- movel %pc@(L(mac_sccbase)),%a0
-#endif /* MAC_USE_SCC_A */
lea %pc@(L(scc_initable_mac)),%a1
7: moveb %a1@+,%d0
jmi 8f
jra 7b
8:
#endif /* MAC_USE_SCC_B */
+
#endif /* SERIAL_DEBUG */
jra L(serial_init_done)
#ifdef SERIAL_DEBUG
-#ifdef MAC_USE_SCC_A
+#if defined(MAC_USE_SCC_A) || defined(MAC_USE_SCC_B)
movel %pc@(L(mac_sccbase)),%a1
+#endif
+
+#ifdef MAC_USE_SCC_A
3: btst #2,%a1@(mac_scc_cha_a_ctrl_offset)
jeq 3b
moveb %d0,%a1@(mac_scc_cha_a_data_offset)
#endif /* MAC_USE_SCC_A */
#ifdef MAC_USE_SCC_B
-#ifndef MAC_USE_SCC_A /* Load mac_sccbase only if needed */
- movel %pc@(L(mac_sccbase)),%a1
-#endif /* MAC_USE_SCC_A */
4: btst #2,%a1@(mac_scc_cha_b_ctrl_offset)
jeq 4b
moveb %d0,%a1@(mac_scc_cha_b_data_offset)
#define flush_cache_range(vma, start, len) do { } while (0)
-#define copy_to_user_page(vma, page, vaddr, dst, src, len) \
-do { \
- u32 addr = virt_to_phys(dst); \
- memcpy((dst), (src), (len)); \
- if (vma->vm_flags & VM_EXEC) { \
- invalidate_icache_range((unsigned) (addr), \
- (unsigned) (addr) + PAGE_SIZE); \
- flush_dcache_range((unsigned) (addr), \
- (unsigned) (addr) + PAGE_SIZE); \
- } \
-} while (0)
-
-#define copy_from_user_page(vma, page, vaddr, dst, src, len) \
-do { \
- memcpy((dst), (src), (len)); \
-} while (0)
+static inline void copy_to_user_page(struct vm_area_struct *vma,
+ struct page *page, unsigned long vaddr,
+ void *dst, void *src, int len)
+{
+ u32 addr = virt_to_phys(dst);
+ memcpy(dst, src, len);
+ if (vma->vm_flags & VM_EXEC) {
+ invalidate_icache_range(addr, addr + PAGE_SIZE);
+ flush_dcache_range(addr, addr + PAGE_SIZE);
+ }
+}
+
+static inline void copy_from_user_page(struct vm_area_struct *vma,
+ struct page *page, unsigned long vaddr,
+ void *dst, void *src, int len)
+{
+ memcpy(dst, src, len);
+}
#endif /* _ASM_MICROBLAZE_CACHEFLUSH_H */
__asm__ __volatile__ ("1: lwx %1, %3, r0; \
cmp %2, %1, %4; \
- beqi %2, 3f; \
+ bnei %2, 3f; \
2: swx %5, %3, r0; \
addic %2, r0, 0; \
bnei %2, 1b; \
* inb_p/inw_p/...
* The macros don't do byte-swapping.
*/
-#define inb(port) readb((u8 *)((port)))
+#define inb(port) readb((u8 *)((unsigned long)(port)))
#define outb(val, port) writeb((val), (u8 *)((unsigned long)(port)))
-#define inw(port) readw((u16 *)((port)))
+#define inw(port) readw((u16 *)((unsigned long)(port)))
#define outw(val, port) writew((val), (u16 *)((unsigned long)(port)))
-#define inl(port) readl((u32 *)((port)))
+#define inl(port) readl((u32 *)((unsigned long)(port)))
#define outl(val, port) writel((val), (u32 *)((unsigned long)(port)))
#define inb_p(port) inb((port))
if ((get_fs().seg < ((unsigned long)addr)) ||
(get_fs().seg < ((unsigned long)addr + size - 1))) {
pr_debug("ACCESS fail: %s at 0x%08x (size 0x%x), seg 0x%08x\n",
- type ? "WRITE" : "READ ", (u32)addr, (u32)size,
+ type ? "WRITE" : "READ ", (__force u32)addr, (u32)size,
(u32)get_fs().seg);
return 0;
}
ok:
pr_debug("ACCESS OK: %s at 0x%08x (size 0x%x), seg 0x%08x\n",
- type ? "WRITE" : "READ ", (u32)addr, (u32)size,
+ type ? "WRITE" : "READ ", (__force u32)addr, (u32)size,
(u32)get_fs().seg);
return 1;
}
/* It is used only first parameter for OP - for wic, wdc */
#define CACHE_RANGE_LOOP_1(start, end, line_length, op) \
do { \
- int volatile temp; \
+ int volatile temp = 0; \
int align = ~(line_length - 1); \
end = ((end & align) == end) ? end - line_length : end & align; \
WARN_ON(end - start < 0); \
CONFIG_USB_HID=y
CONFIG_USB_SUPPORT=y
CONFIG_USB=y
-CONFIG_USB_SUSPEND=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_EHCI_ROOT_HUB_TT=y
CONFIG_USB_EHCI_TT_NEWSCHED=y
CONFIG_USB_HIDDEV=y
CONFIG_USB=y
CONFIG_USB_DYNAMIC_MINORS=y
-CONFIG_USB_SUSPEND=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_EHCI_HCD_PLATFORM=y
CONFIG_USB_EHCI_ROOT_HUB_TT=y
CONFIG_USB_DEVICEFS=y
# CONFIG_USB_DEVICE_CLASS is not set
CONFIG_USB_DYNAMIC_MINORS=y
-CONFIG_USB_SUSPEND=y
CONFIG_USB_OTG_WHITELIST=y
CONFIG_USB_MON=y
CONFIG_USB_EHCI_HCD=y
+++ /dev/null
-/*
-* This file is subject to the terms and conditions of the GNU General Public
-* License. See the file "COPYING" in the main directory of this archive
-* for more details.
-*
-* Copyright (C) 2012 MIPS Technologies, Inc. All rights reserved.
-* Authors: Sanjay Lal <sanjayl@kymasys.com>
-*/
-
-#ifndef __LINUX_KVM_MIPS_H
-#define __LINUX_KVM_MIPS_H
-
-#include <linux/types.h>
-
-#define __KVM_MIPS
-
-#define N_MIPS_COPROC_REGS 32
-#define N_MIPS_COPROC_SEL 8
-
-/* for KVM_GET_REGS and KVM_SET_REGS */
-struct kvm_regs {
- __u32 gprs[32];
- __u32 hi;
- __u32 lo;
- __u32 pc;
-
- __u32 cp0reg[N_MIPS_COPROC_REGS][N_MIPS_COPROC_SEL];
-};
-
-/* for KVM_GET_SREGS and KVM_SET_SREGS */
-struct kvm_sregs {
-};
-
-/* for KVM_GET_FPU and KVM_SET_FPU */
-struct kvm_fpu {
-};
-
-struct kvm_debug_exit_arch {
-};
-
-/* for KVM_SET_GUEST_DEBUG */
-struct kvm_guest_debug_arch {
-};
-
-struct kvm_mips_interrupt {
- /* in */
- __u32 cpu;
- __u32 irq;
-};
-
-/* definition of registers in kvm_run */
-struct kvm_sync_regs {
-};
-
-#endif /* __LINUX_KVM_MIPS_H */
uint32_t cause);
int (*irq_clear) (struct kvm_vcpu *vcpu, unsigned int priority,
uint32_t cause);
- int (*vcpu_ioctl_get_regs) (struct kvm_vcpu *vcpu,
- struct kvm_regs *regs);
- int (*vcpu_ioctl_set_regs) (struct kvm_vcpu *vcpu,
- struct kvm_regs *regs);
};
extern struct kvm_mips_callbacks *kvm_mips_callbacks;
int kvm_mips_emulation_init(struct kvm_mips_callbacks **install_callbacks);
--- /dev/null
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2012 MIPS Technologies, Inc. All rights reserved.
+ * Copyright (C) 2013 Cavium, Inc.
+ * Authors: Sanjay Lal <sanjayl@kymasys.com>
+ */
+
+#ifndef __LINUX_KVM_MIPS_H
+#define __LINUX_KVM_MIPS_H
+
+#include <linux/types.h>
+
+/*
+ * KVM MIPS specific structures and definitions.
+ *
+ * Some parts derived from the x86 version of this file.
+ */
+
+/*
+ * for KVM_GET_REGS and KVM_SET_REGS
+ *
+ * If Config[AT] is zero (32-bit CPU), the register contents are
+ * stored in the lower 32-bits of the struct kvm_regs fields and sign
+ * extended to 64-bits.
+ */
+struct kvm_regs {
+ /* out (KVM_GET_REGS) / in (KVM_SET_REGS) */
+ __u64 gpr[32];
+ __u64 hi;
+ __u64 lo;
+ __u64 pc;
+};
+
+/*
+ * for KVM_GET_FPU and KVM_SET_FPU
+ *
+ * If Status[FR] is zero (32-bit FPU), the upper 32-bits of the FPRs
+ * are zero filled.
+ */
+struct kvm_fpu {
+ __u64 fpr[32];
+ __u32 fir;
+ __u32 fccr;
+ __u32 fexr;
+ __u32 fenr;
+ __u32 fcsr;
+ __u32 pad;
+};
+
+
+/*
+ * For MIPS, we use KVM_SET_ONE_REG and KVM_GET_ONE_REG to access CP0
+ * registers. The id field is broken down as follows:
+ *
+ * bits[2..0] - Register 'sel' index.
+ * bits[7..3] - Register 'rd' index.
+ * bits[15..8] - Must be zero.
+ * bits[63..16] - 1 -> CP0 registers.
+ *
+ * Other sets registers may be added in the future. Each set would
+ * have its own identifier in bits[63..16].
+ *
+ * The addr field of struct kvm_one_reg must point to an aligned
+ * 64-bit wide location. For registers that are narrower than
+ * 64-bits, the value is stored in the low order bits of the location,
+ * and sign extended to 64-bits.
+ *
+ * The registers defined in struct kvm_regs are also accessible, the
+ * id values for these are below.
+ */
+
+#define KVM_REG_MIPS_R0 0
+#define KVM_REG_MIPS_R1 1
+#define KVM_REG_MIPS_R2 2
+#define KVM_REG_MIPS_R3 3
+#define KVM_REG_MIPS_R4 4
+#define KVM_REG_MIPS_R5 5
+#define KVM_REG_MIPS_R6 6
+#define KVM_REG_MIPS_R7 7
+#define KVM_REG_MIPS_R8 8
+#define KVM_REG_MIPS_R9 9
+#define KVM_REG_MIPS_R10 10
+#define KVM_REG_MIPS_R11 11
+#define KVM_REG_MIPS_R12 12
+#define KVM_REG_MIPS_R13 13
+#define KVM_REG_MIPS_R14 14
+#define KVM_REG_MIPS_R15 15
+#define KVM_REG_MIPS_R16 16
+#define KVM_REG_MIPS_R17 17
+#define KVM_REG_MIPS_R18 18
+#define KVM_REG_MIPS_R19 19
+#define KVM_REG_MIPS_R20 20
+#define KVM_REG_MIPS_R21 21
+#define KVM_REG_MIPS_R22 22
+#define KVM_REG_MIPS_R23 23
+#define KVM_REG_MIPS_R24 24
+#define KVM_REG_MIPS_R25 25
+#define KVM_REG_MIPS_R26 26
+#define KVM_REG_MIPS_R27 27
+#define KVM_REG_MIPS_R28 28
+#define KVM_REG_MIPS_R29 29
+#define KVM_REG_MIPS_R30 30
+#define KVM_REG_MIPS_R31 31
+
+#define KVM_REG_MIPS_HI 32
+#define KVM_REG_MIPS_LO 33
+#define KVM_REG_MIPS_PC 34
+
+/*
+ * KVM MIPS specific structures and definitions
+ *
+ */
+struct kvm_debug_exit_arch {
+ __u64 epc;
+};
+
+/* for KVM_SET_GUEST_DEBUG */
+struct kvm_guest_debug_arch {
+};
+
+/* definition of registers in kvm_run */
+struct kvm_sync_regs {
+};
+
+/* dummy definition */
+struct kvm_sregs {
+};
+
+struct kvm_mips_interrupt {
+ /* in */
+ __u32 cpu;
+ __u32 irq;
+};
+
+#endif /* __LINUX_KVM_MIPS_H */
long
kvm_arch_dev_ioctl(struct file *filp, unsigned int ioctl, unsigned long arg)
{
- return -EINVAL;
+ return -ENOIOCTLCMD;
}
void kvm_arch_free_memslot(struct kvm_memory_slot *free,
kvm_arch_vcpu_ioctl_set_guest_debug(struct kvm_vcpu *vcpu,
struct kvm_guest_debug *dbg)
{
- return -EINVAL;
+ return -ENOIOCTLCMD;
}
int kvm_arch_vcpu_ioctl_run(struct kvm_vcpu *vcpu, struct kvm_run *run)
kvm_arch_vcpu_ioctl_get_mpstate(struct kvm_vcpu *vcpu,
struct kvm_mp_state *mp_state)
{
- return -EINVAL;
+ return -ENOIOCTLCMD;
}
int
kvm_arch_vcpu_ioctl_set_mpstate(struct kvm_vcpu *vcpu,
struct kvm_mp_state *mp_state)
{
- return -EINVAL;
+ return -ENOIOCTLCMD;
+}
+
+#define KVM_REG_MIPS_CP0_INDEX (0x10000 + 8 * 0 + 0)
+#define KVM_REG_MIPS_CP0_ENTRYLO0 (0x10000 + 8 * 2 + 0)
+#define KVM_REG_MIPS_CP0_ENTRYLO1 (0x10000 + 8 * 3 + 0)
+#define KVM_REG_MIPS_CP0_CONTEXT (0x10000 + 8 * 4 + 0)
+#define KVM_REG_MIPS_CP0_USERLOCAL (0x10000 + 8 * 4 + 2)
+#define KVM_REG_MIPS_CP0_PAGEMASK (0x10000 + 8 * 5 + 0)
+#define KVM_REG_MIPS_CP0_PAGEGRAIN (0x10000 + 8 * 5 + 1)
+#define KVM_REG_MIPS_CP0_WIRED (0x10000 + 8 * 6 + 0)
+#define KVM_REG_MIPS_CP0_HWRENA (0x10000 + 8 * 7 + 0)
+#define KVM_REG_MIPS_CP0_BADVADDR (0x10000 + 8 * 8 + 0)
+#define KVM_REG_MIPS_CP0_COUNT (0x10000 + 8 * 9 + 0)
+#define KVM_REG_MIPS_CP0_ENTRYHI (0x10000 + 8 * 10 + 0)
+#define KVM_REG_MIPS_CP0_COMPARE (0x10000 + 8 * 11 + 0)
+#define KVM_REG_MIPS_CP0_STATUS (0x10000 + 8 * 12 + 0)
+#define KVM_REG_MIPS_CP0_CAUSE (0x10000 + 8 * 13 + 0)
+#define KVM_REG_MIPS_CP0_EBASE (0x10000 + 8 * 15 + 1)
+#define KVM_REG_MIPS_CP0_CONFIG (0x10000 + 8 * 16 + 0)
+#define KVM_REG_MIPS_CP0_CONFIG1 (0x10000 + 8 * 16 + 1)
+#define KVM_REG_MIPS_CP0_CONFIG2 (0x10000 + 8 * 16 + 2)
+#define KVM_REG_MIPS_CP0_CONFIG3 (0x10000 + 8 * 16 + 3)
+#define KVM_REG_MIPS_CP0_CONFIG7 (0x10000 + 8 * 16 + 7)
+#define KVM_REG_MIPS_CP0_XCONTEXT (0x10000 + 8 * 20 + 0)
+#define KVM_REG_MIPS_CP0_ERROREPC (0x10000 + 8 * 30 + 0)
+
+static u64 kvm_mips_get_one_regs[] = {
+ KVM_REG_MIPS_R0,
+ KVM_REG_MIPS_R1,
+ KVM_REG_MIPS_R2,
+ KVM_REG_MIPS_R3,
+ KVM_REG_MIPS_R4,
+ KVM_REG_MIPS_R5,
+ KVM_REG_MIPS_R6,
+ KVM_REG_MIPS_R7,
+ KVM_REG_MIPS_R8,
+ KVM_REG_MIPS_R9,
+ KVM_REG_MIPS_R10,
+ KVM_REG_MIPS_R11,
+ KVM_REG_MIPS_R12,
+ KVM_REG_MIPS_R13,
+ KVM_REG_MIPS_R14,
+ KVM_REG_MIPS_R15,
+ KVM_REG_MIPS_R16,
+ KVM_REG_MIPS_R17,
+ KVM_REG_MIPS_R18,
+ KVM_REG_MIPS_R19,
+ KVM_REG_MIPS_R20,
+ KVM_REG_MIPS_R21,
+ KVM_REG_MIPS_R22,
+ KVM_REG_MIPS_R23,
+ KVM_REG_MIPS_R24,
+ KVM_REG_MIPS_R25,
+ KVM_REG_MIPS_R26,
+ KVM_REG_MIPS_R27,
+ KVM_REG_MIPS_R28,
+ KVM_REG_MIPS_R29,
+ KVM_REG_MIPS_R30,
+ KVM_REG_MIPS_R31,
+
+ KVM_REG_MIPS_HI,
+ KVM_REG_MIPS_LO,
+ KVM_REG_MIPS_PC,
+
+ KVM_REG_MIPS_CP0_INDEX,
+ KVM_REG_MIPS_CP0_CONTEXT,
+ KVM_REG_MIPS_CP0_PAGEMASK,
+ KVM_REG_MIPS_CP0_WIRED,
+ KVM_REG_MIPS_CP0_BADVADDR,
+ KVM_REG_MIPS_CP0_ENTRYHI,
+ KVM_REG_MIPS_CP0_STATUS,
+ KVM_REG_MIPS_CP0_CAUSE,
+ /* EPC set via kvm_regs, et al. */
+ KVM_REG_MIPS_CP0_CONFIG,
+ KVM_REG_MIPS_CP0_CONFIG1,
+ KVM_REG_MIPS_CP0_CONFIG2,
+ KVM_REG_MIPS_CP0_CONFIG3,
+ KVM_REG_MIPS_CP0_CONFIG7,
+ KVM_REG_MIPS_CP0_ERROREPC
+};
+
+static int kvm_mips_get_reg(struct kvm_vcpu *vcpu,
+ const struct kvm_one_reg *reg)
+{
+ u64 __user *uaddr = (u64 __user *)(long)reg->addr;
+
+ struct mips_coproc *cop0 = vcpu->arch.cop0;
+ s64 v;
+
+ switch (reg->id) {
+ case KVM_REG_MIPS_R0 ... KVM_REG_MIPS_R31:
+ v = (long)vcpu->arch.gprs[reg->id - KVM_REG_MIPS_R0];
+ break;
+ case KVM_REG_MIPS_HI:
+ v = (long)vcpu->arch.hi;
+ break;
+ case KVM_REG_MIPS_LO:
+ v = (long)vcpu->arch.lo;
+ break;
+ case KVM_REG_MIPS_PC:
+ v = (long)vcpu->arch.pc;
+ break;
+
+ case KVM_REG_MIPS_CP0_INDEX:
+ v = (long)kvm_read_c0_guest_index(cop0);
+ break;
+ case KVM_REG_MIPS_CP0_CONTEXT:
+ v = (long)kvm_read_c0_guest_context(cop0);
+ break;
+ case KVM_REG_MIPS_CP0_PAGEMASK:
+ v = (long)kvm_read_c0_guest_pagemask(cop0);
+ break;
+ case KVM_REG_MIPS_CP0_WIRED:
+ v = (long)kvm_read_c0_guest_wired(cop0);
+ break;
+ case KVM_REG_MIPS_CP0_BADVADDR:
+ v = (long)kvm_read_c0_guest_badvaddr(cop0);
+ break;
+ case KVM_REG_MIPS_CP0_ENTRYHI:
+ v = (long)kvm_read_c0_guest_entryhi(cop0);
+ break;
+ case KVM_REG_MIPS_CP0_STATUS:
+ v = (long)kvm_read_c0_guest_status(cop0);
+ break;
+ case KVM_REG_MIPS_CP0_CAUSE:
+ v = (long)kvm_read_c0_guest_cause(cop0);
+ break;
+ case KVM_REG_MIPS_CP0_ERROREPC:
+ v = (long)kvm_read_c0_guest_errorepc(cop0);
+ break;
+ case KVM_REG_MIPS_CP0_CONFIG:
+ v = (long)kvm_read_c0_guest_config(cop0);
+ break;
+ case KVM_REG_MIPS_CP0_CONFIG1:
+ v = (long)kvm_read_c0_guest_config1(cop0);
+ break;
+ case KVM_REG_MIPS_CP0_CONFIG2:
+ v = (long)kvm_read_c0_guest_config2(cop0);
+ break;
+ case KVM_REG_MIPS_CP0_CONFIG3:
+ v = (long)kvm_read_c0_guest_config3(cop0);
+ break;
+ case KVM_REG_MIPS_CP0_CONFIG7:
+ v = (long)kvm_read_c0_guest_config7(cop0);
+ break;
+ default:
+ return -EINVAL;
+ }
+ return put_user(v, uaddr);
+}
+
+static int kvm_mips_set_reg(struct kvm_vcpu *vcpu,
+ const struct kvm_one_reg *reg)
+{
+ u64 __user *uaddr = (u64 __user *)(long)reg->addr;
+ struct mips_coproc *cop0 = vcpu->arch.cop0;
+ u64 v;
+
+ if (get_user(v, uaddr) != 0)
+ return -EFAULT;
+
+ switch (reg->id) {
+ case KVM_REG_MIPS_R0:
+ /* Silently ignore requests to set $0 */
+ break;
+ case KVM_REG_MIPS_R1 ... KVM_REG_MIPS_R31:
+ vcpu->arch.gprs[reg->id - KVM_REG_MIPS_R0] = v;
+ break;
+ case KVM_REG_MIPS_HI:
+ vcpu->arch.hi = v;
+ break;
+ case KVM_REG_MIPS_LO:
+ vcpu->arch.lo = v;
+ break;
+ case KVM_REG_MIPS_PC:
+ vcpu->arch.pc = v;
+ break;
+
+ case KVM_REG_MIPS_CP0_INDEX:
+ kvm_write_c0_guest_index(cop0, v);
+ break;
+ case KVM_REG_MIPS_CP0_CONTEXT:
+ kvm_write_c0_guest_context(cop0, v);
+ break;
+ case KVM_REG_MIPS_CP0_PAGEMASK:
+ kvm_write_c0_guest_pagemask(cop0, v);
+ break;
+ case KVM_REG_MIPS_CP0_WIRED:
+ kvm_write_c0_guest_wired(cop0, v);
+ break;
+ case KVM_REG_MIPS_CP0_BADVADDR:
+ kvm_write_c0_guest_badvaddr(cop0, v);
+ break;
+ case KVM_REG_MIPS_CP0_ENTRYHI:
+ kvm_write_c0_guest_entryhi(cop0, v);
+ break;
+ case KVM_REG_MIPS_CP0_STATUS:
+ kvm_write_c0_guest_status(cop0, v);
+ break;
+ case KVM_REG_MIPS_CP0_CAUSE:
+ kvm_write_c0_guest_cause(cop0, v);
+ break;
+ case KVM_REG_MIPS_CP0_ERROREPC:
+ kvm_write_c0_guest_errorepc(cop0, v);
+ break;
+ default:
+ return -EINVAL;
+ }
+ return 0;
}
long
struct kvm_vcpu *vcpu = filp->private_data;
void __user *argp = (void __user *)arg;
long r;
- int intr;
switch (ioctl) {
+ case KVM_SET_ONE_REG:
+ case KVM_GET_ONE_REG: {
+ struct kvm_one_reg reg;
+ if (copy_from_user(®, argp, sizeof(reg)))
+ return -EFAULT;
+ if (ioctl == KVM_SET_ONE_REG)
+ return kvm_mips_set_reg(vcpu, ®);
+ else
+ return kvm_mips_get_reg(vcpu, ®);
+ }
+ case KVM_GET_REG_LIST: {
+ struct kvm_reg_list __user *user_list = argp;
+ u64 __user *reg_dest;
+ struct kvm_reg_list reg_list;
+ unsigned n;
+
+ if (copy_from_user(®_list, user_list, sizeof(reg_list)))
+ return -EFAULT;
+ n = reg_list.n;
+ reg_list.n = ARRAY_SIZE(kvm_mips_get_one_regs);
+ if (copy_to_user(user_list, ®_list, sizeof(reg_list)))
+ return -EFAULT;
+ if (n < reg_list.n)
+ return -E2BIG;
+ reg_dest = user_list->reg;
+ if (copy_to_user(reg_dest, kvm_mips_get_one_regs,
+ sizeof(kvm_mips_get_one_regs)))
+ return -EFAULT;
+ return 0;
+ }
case KVM_NMI:
/* Treat the NMI as a CPU reset */
r = kvm_mips_reset_vcpu(vcpu);
if (copy_from_user(&irq, argp, sizeof(irq)))
goto out;
- intr = (int)irq.irq;
-
kvm_debug("[%d] %s: irq: %d\n", vcpu->vcpu_id, __func__,
irq.irq);
break;
}
default:
- r = -EINVAL;
+ r = -ENOIOCTLCMD;
}
out:
switch (ioctl) {
default:
- r = -EINVAL;
+ r = -ENOIOCTLCMD;
}
return r;
int
kvm_arch_vcpu_ioctl_get_sregs(struct kvm_vcpu *vcpu, struct kvm_sregs *sregs)
{
- return -ENOTSUPP;
+ return -ENOIOCTLCMD;
}
int
kvm_arch_vcpu_ioctl_set_sregs(struct kvm_vcpu *vcpu, struct kvm_sregs *sregs)
{
- return -ENOTSUPP;
+ return -ENOIOCTLCMD;
}
int kvm_arch_vcpu_postcreate(struct kvm_vcpu *vcpu)
int kvm_arch_vcpu_ioctl_get_fpu(struct kvm_vcpu *vcpu, struct kvm_fpu *fpu)
{
- return -ENOTSUPP;
+ return -ENOIOCTLCMD;
}
int kvm_arch_vcpu_ioctl_set_fpu(struct kvm_vcpu *vcpu, struct kvm_fpu *fpu)
{
- return -ENOTSUPP;
+ return -ENOIOCTLCMD;
}
int kvm_arch_vcpu_fault(struct kvm_vcpu *vcpu, struct vm_fault *vmf)
int r;
switch (ext) {
+ case KVM_CAP_ONE_REG:
+ r = 1;
+ break;
case KVM_CAP_COALESCED_MMIO:
r = KVM_COALESCED_MMIO_PAGE_OFFSET;
break;
break;
}
return r;
-
}
int kvm_cpu_has_pending_timer(struct kvm_vcpu *vcpu)
{
int i;
- for (i = 0; i < 32; i++)
- vcpu->arch.gprs[i] = regs->gprs[i];
-
+ for (i = 1; i < ARRAY_SIZE(vcpu->arch.gprs); i++)
+ vcpu->arch.gprs[i] = regs->gpr[i];
+ vcpu->arch.gprs[0] = 0; /* zero is special, and cannot be set. */
vcpu->arch.hi = regs->hi;
vcpu->arch.lo = regs->lo;
vcpu->arch.pc = regs->pc;
- return kvm_mips_callbacks->vcpu_ioctl_set_regs(vcpu, regs);
+ return 0;
}
int kvm_arch_vcpu_ioctl_get_regs(struct kvm_vcpu *vcpu, struct kvm_regs *regs)
{
int i;
- for (i = 0; i < 32; i++)
- regs->gprs[i] = vcpu->arch.gprs[i];
+ for (i = 0; i < ARRAY_SIZE(vcpu->arch.gprs); i++)
+ regs->gpr[i] = vcpu->arch.gprs[i];
regs->hi = vcpu->arch.hi;
regs->lo = vcpu->arch.lo;
regs->pc = vcpu->arch.pc;
- return kvm_mips_callbacks->vcpu_ioctl_get_regs(vcpu, regs);
+ return 0;
}
void kvm_mips_comparecount_func(unsigned long data)
#include <linux/delay.h>
#include <linux/module.h>
#include <linux/kvm_host.h>
+#include <linux/srcu.h>
+
#include <asm/cpu.h>
#include <asm/bootinfo.h>
}
}
-static void kvm_mips_map_page(struct kvm *kvm, gfn_t gfn)
+static int kvm_mips_map_page(struct kvm *kvm, gfn_t gfn)
{
+ int srcu_idx, err = 0;
pfn_t pfn;
if (kvm->arch.guest_pmap[gfn] != KVM_INVALID_PAGE)
- return;
+ return 0;
+ srcu_idx = srcu_read_lock(&kvm->srcu);
pfn = kvm_mips_gfn_to_pfn(kvm, gfn);
if (kvm_mips_is_error_pfn(pfn)) {
- panic("Couldn't get pfn for gfn %#" PRIx64 "!\n", gfn);
+ kvm_err("Couldn't get pfn for gfn %#" PRIx64 "!\n", gfn);
+ err = -EFAULT;
+ goto out;
}
kvm->arch.guest_pmap[gfn] = pfn;
- return;
+out:
+ srcu_read_unlock(&kvm->srcu, srcu_idx);
+ return err;
}
/* Translate guest KSEG0 addresses to Host PA */
gva);
return KVM_INVALID_PAGE;
}
- kvm_mips_map_page(vcpu->kvm, gfn);
+
+ if (kvm_mips_map_page(vcpu->kvm, gfn) < 0)
+ return KVM_INVALID_ADDR;
+
return (kvm->arch.guest_pmap[gfn] << PAGE_SHIFT) + offset;
}
even = !(gfn & 0x1);
vaddr = badvaddr & (PAGE_MASK << 1);
- kvm_mips_map_page(vcpu->kvm, gfn);
- kvm_mips_map_page(vcpu->kvm, gfn ^ 0x1);
+ if (kvm_mips_map_page(vcpu->kvm, gfn) < 0)
+ return -1;
+
+ if (kvm_mips_map_page(vcpu->kvm, gfn ^ 0x1) < 0)
+ return -1;
if (even) {
pfn0 = kvm->arch.guest_pmap[gfn];
pfn0 = 0;
pfn1 = 0;
} else {
- kvm_mips_map_page(kvm, mips3_tlbpfn_to_paddr(tlb->tlb_lo0) >> PAGE_SHIFT);
- kvm_mips_map_page(kvm, mips3_tlbpfn_to_paddr(tlb->tlb_lo1) >> PAGE_SHIFT);
+ if (kvm_mips_map_page(kvm, mips3_tlbpfn_to_paddr(tlb->tlb_lo0) >> PAGE_SHIFT) < 0)
+ return -1;
+
+ if (kvm_mips_map_page(kvm, mips3_tlbpfn_to_paddr(tlb->tlb_lo1) >> PAGE_SHIFT) < 0)
+ return -1;
pfn0 = kvm->arch.guest_pmap[mips3_tlbpfn_to_paddr(tlb->tlb_lo0) >> PAGE_SHIFT];
pfn1 = kvm->arch.guest_pmap[mips3_tlbpfn_to_paddr(tlb->tlb_lo1) >> PAGE_SHIFT];
return ret;
}
-static int
-kvm_trap_emul_ioctl_set_regs(struct kvm_vcpu *vcpu, struct kvm_regs *regs)
-{
- struct mips_coproc *cop0 = vcpu->arch.cop0;
-
- kvm_write_c0_guest_index(cop0, regs->cp0reg[MIPS_CP0_TLB_INDEX][0]);
- kvm_write_c0_guest_context(cop0, regs->cp0reg[MIPS_CP0_TLB_CONTEXT][0]);
- kvm_write_c0_guest_badvaddr(cop0, regs->cp0reg[MIPS_CP0_BAD_VADDR][0]);
- kvm_write_c0_guest_entryhi(cop0, regs->cp0reg[MIPS_CP0_TLB_HI][0]);
- kvm_write_c0_guest_epc(cop0, regs->cp0reg[MIPS_CP0_EXC_PC][0]);
-
- kvm_write_c0_guest_status(cop0, regs->cp0reg[MIPS_CP0_STATUS][0]);
- kvm_write_c0_guest_cause(cop0, regs->cp0reg[MIPS_CP0_CAUSE][0]);
- kvm_write_c0_guest_pagemask(cop0,
- regs->cp0reg[MIPS_CP0_TLB_PG_MASK][0]);
- kvm_write_c0_guest_wired(cop0, regs->cp0reg[MIPS_CP0_TLB_WIRED][0]);
- kvm_write_c0_guest_errorepc(cop0, regs->cp0reg[MIPS_CP0_ERROR_PC][0]);
-
- return 0;
-}
-
-static int
-kvm_trap_emul_ioctl_get_regs(struct kvm_vcpu *vcpu, struct kvm_regs *regs)
-{
- struct mips_coproc *cop0 = vcpu->arch.cop0;
-
- regs->cp0reg[MIPS_CP0_TLB_INDEX][0] = kvm_read_c0_guest_index(cop0);
- regs->cp0reg[MIPS_CP0_TLB_CONTEXT][0] = kvm_read_c0_guest_context(cop0);
- regs->cp0reg[MIPS_CP0_BAD_VADDR][0] = kvm_read_c0_guest_badvaddr(cop0);
- regs->cp0reg[MIPS_CP0_TLB_HI][0] = kvm_read_c0_guest_entryhi(cop0);
- regs->cp0reg[MIPS_CP0_EXC_PC][0] = kvm_read_c0_guest_epc(cop0);
-
- regs->cp0reg[MIPS_CP0_STATUS][0] = kvm_read_c0_guest_status(cop0);
- regs->cp0reg[MIPS_CP0_CAUSE][0] = kvm_read_c0_guest_cause(cop0);
- regs->cp0reg[MIPS_CP0_TLB_PG_MASK][0] =
- kvm_read_c0_guest_pagemask(cop0);
- regs->cp0reg[MIPS_CP0_TLB_WIRED][0] = kvm_read_c0_guest_wired(cop0);
- regs->cp0reg[MIPS_CP0_ERROR_PC][0] = kvm_read_c0_guest_errorepc(cop0);
-
- regs->cp0reg[MIPS_CP0_CONFIG][0] = kvm_read_c0_guest_config(cop0);
- regs->cp0reg[MIPS_CP0_CONFIG][1] = kvm_read_c0_guest_config1(cop0);
- regs->cp0reg[MIPS_CP0_CONFIG][2] = kvm_read_c0_guest_config2(cop0);
- regs->cp0reg[MIPS_CP0_CONFIG][3] = kvm_read_c0_guest_config3(cop0);
- regs->cp0reg[MIPS_CP0_CONFIG][7] = kvm_read_c0_guest_config7(cop0);
-
- return 0;
-}
-
static int kvm_trap_emul_vm_init(struct kvm *kvm)
{
return 0;
.dequeue_io_int = kvm_mips_dequeue_io_int_cb,
.irq_deliver = kvm_mips_irq_deliver_cb,
.irq_clear = kvm_mips_irq_clear_cb,
- .vcpu_ioctl_get_regs = kvm_trap_emul_ioctl_get_regs,
- .vcpu_ioctl_set_regs = kvm_trap_emul_ioctl_set_regs,
};
int kvm_mips_emulation_init(struct kvm_mips_callbacks **install_callbacks)
return channel ? 15 : 14;
}
+#include <asm-generic/pci_iomap.h>
+
#endif /* _ASM_PCI_H */
mov (REG_D0,fp),d0
mov (REG_A0,fp),a0
calls (a0)
+ GET_THREAD_INFO a2 # A2 must be set on return from sys_exit()
clr d0
mov d0,(REG_D0,fp)
jmp syscall_exit
and EPSW_nSL,d0
beq resume_kernel # returning to supervisor mode
- btst _TIF_SYSCALL_TRACE,d2
- beq work_pending
LOCAL_IRQ_ENABLE # could let syscall_trace_exit() call
# schedule() instead
+ btst _TIF_SYSCALL_TRACE,d2
+ beq work_pending
mov fp,d0
call syscall_trace_exit[],0 # do_syscall_trace(regs)
jmp resume_userspace
work_resched:
call schedule[],0
+resume_userspace:
# make sure we don't miss an interrupt setting need_resched or
# sigpending between sampling and the rti
LOCAL_IRQ_DISABLE
mov (TI_flags,a2),d2
btst _TIF_WORK_MASK,d2
beq restore_all
+
+ LOCAL_IRQ_ENABLE
btst _TIF_NEED_RESCHED,d2
bne work_resched
and EPSW_nSL,d0
beq resume_kernel # returning to supervisor mode
-ENTRY(resume_userspace)
- # make sure we don't miss an interrupt setting need_resched or
- # sigpending between sampling and the rti
- LOCAL_IRQ_DISABLE
-
- # is there any work to be done on int/exception return?
- mov (TI_flags,a2),d2
- btst _TIF_WORK_MASK,d2
- bne work_pending
- jmp restore_all
-
#ifdef CONFIG_PREEMPT
ENTRY(resume_kernel)
LOCAL_IRQ_DISABLE
#include <linux/delay.h>
#include <linux/irq.h>
#include <asm/io.h>
+#include <asm/irq.h>
#include "pci-asb2305.h"
unsigned int pci_probe = 1;
endif
# select which processor to optimise for
-cflags-$(CONFIG_PA7100) += -march=1.1 -mschedule=7100
+cflags-$(CONFIG_PA7000) += -march=1.1 -mschedule=7100
cflags-$(CONFIG_PA7200) += -march=1.1 -mschedule=7200
cflags-$(CONFIG_PA7100LC) += -march=1.1 -mschedule=7100LC
cflags-$(CONFIG_PA7300LC) += -march=1.1 -mschedule=7300
SAVE_SP (%sr4, PT_SR4 (\regs))
SAVE_SP (%sr5, PT_SR5 (\regs))
SAVE_SP (%sr6, PT_SR6 (\regs))
- SAVE_SP (%sr7, PT_SR7 (\regs))
SAVE_CR (%cr17, PT_IASQ0(\regs))
mtctl %r0, %cr17
typedef struct {
unsigned int __softirq_pending;
-#ifdef CONFIG_DEBUG_STACKOVERFLOW
unsigned int kernel_stack_usage;
-#ifdef CONFIG_IRQSTACKS
unsigned int irq_stack_usage;
- unsigned int irq_stack_counter;
-#endif
-#endif
#ifdef CONFIG_SMP
unsigned int irq_resched_count;
unsigned int irq_call_count;
#endif
+ unsigned int irq_unaligned_count;
+ unsigned int irq_fpassist_count;
unsigned int irq_tlb_count;
} ____cacheline_aligned irq_cpustat_t;
static inline int pfn_to_nid(unsigned long pfn)
{
unsigned int i;
- unsigned char r;
if (unlikely(pfn_is_io(pfn)))
return 0;
i = pfn >> PFNNID_SHIFT;
BUG_ON(i >= ARRAY_SIZE(pfnnid_map));
- r = pfnnid_map[i];
- BUG_ON(r == 0xff);
- return (int)r;
+ return (int)pfnnid_map[i];
}
static inline int pfn_valid(int pfn)
#include <asm/ptrace.h>
#include <asm/types.h>
#include <asm/percpu.h>
-
#endif /* __ASSEMBLY__ */
/*
#ifndef __ASSEMBLY__
-/*
- * IRQ STACK - used for irq handler
- */
-#ifdef __KERNEL__
-
-#include <linux/spinlock_types.h>
-
-#define IRQ_STACK_SIZE (4096 << 2) /* 16k irq stack size */
-
-union irq_stack_union {
- unsigned long stack[IRQ_STACK_SIZE/sizeof(unsigned long)];
- raw_spinlock_t lock;
-};
-
-DECLARE_PER_CPU(union irq_stack_union, irq_stack_union);
-
-void call_on_stack(unsigned long p1, void *func, unsigned long new_stack);
-
-#endif /* __KERNEL__ */
-
/*
* Data detected about CPUs at boot time which is the same for all CPU's.
* HP boxes are SMP - ie identical processors.
static void setup_bus_id(struct parisc_device *padev)
{
struct hardware_path path;
- char name[20];
+ char name[28];
char *output = name;
int i;
rsm PSW_SM_I, %r0 /* barrier for "Relied upon Translation */
mtsp %r0, %sr4
mtsp %r0, %sr5
- mfsp %sr7, %r1
- or,= %r0,%r1,%r0 /* Only save sr7 in sr3 if sr7 != 0 */
- mtsp %r1, %sr3
+ mtsp %r0, %sr6
tovirt_r1 %r29
load32 KERNEL_PSW, %r1
rsm PSW_SM_QUIET,%r0 /* second "heavy weight" ctl op */
- mtsp %r0, %sr6
- mtsp %r0, %sr7
mtctl %r0, %cr17 /* Clear IIASQ tail */
mtctl %r0, %cr17 /* Clear IIASQ head */
mtctl %r1, %ipsw
/* we save the registers in the task struct */
+ copy %r30, %r17
mfctl %cr30, %r1
+ ldo THREAD_SZ_ALGN(%r1), %r30
+ mtsp %r0,%sr7
+ mtsp %r16,%sr3
tophys %r1,%r9
LDREG TI_TASK(%r9), %r1 /* thread_info -> task_struct */
tophys %r1,%r9
ldo TASK_REGS(%r9),%r9
- STREG %r30, PT_GR30(%r9)
+ STREG %r17,PT_GR30(%r9)
STREG %r29,PT_GR29(%r9)
STREG %r26,PT_GR26(%r9)
+ STREG %r16,PT_SR7(%r9)
copy %r9,%r29
- mfctl %cr30, %r1
- ldo THREAD_SZ_ALGN(%r1), %r30
.endm
.macro get_stack_use_r30
/* we put a struct pt_regs on the stack and save the registers there */
tophys %r30,%r9
- STREG %r30,PT_GR30(%r9)
+ copy %r30,%r1
ldo PT_SZ_ALGN(%r30),%r30
+ STREG %r1,PT_GR30(%r9)
STREG %r29,PT_GR29(%r9)
STREG %r26,PT_GR26(%r9)
+ STREG %r16,PT_SR7(%r9)
copy %r9,%r29
.endm
{HPHW_NPROC,0x5DD,0x4,0x81,"Duet W2"},
{HPHW_NPROC,0x5DE,0x4,0x81,"Piccolo W+"},
{HPHW_NPROC,0x5DF,0x4,0x81,"Cantata W2"},
+ {HPHW_NPROC,0x5DF,0x0,0x00,"Marcato W+? (rp5470)"},
{HPHW_NPROC,0x5E0,0x4,0x91,"Cantata DC- W2"},
{HPHW_NPROC,0x5E1,0x4,0x91,"Crescendo DC- W2"},
{HPHW_NPROC,0x5E2,0x4,0x91,"Crescendo 650 W2"},
#include <linux/interrupt.h>
#include <linux/kernel_stat.h>
#include <linux/seq_file.h>
-#include <linux/spinlock.h>
#include <linux/types.h>
#include <asm/io.h>
#include <asm/smp.h>
+#include <asm/ldcw.h>
#undef PARISC_IRQ_CR16_COUNTS
for_each_online_cpu(j)
seq_printf(p, "%10u ", irq_stats(j)->irq_stack_usage);
seq_puts(p, " Interrupt stack usage\n");
- seq_printf(p, "%*s: ", prec, "ISC");
- for_each_online_cpu(j)
- seq_printf(p, "%10u ", irq_stats(j)->irq_stack_counter);
- seq_puts(p, " Interrupt stack usage counter\n");
# endif
#endif
#ifdef CONFIG_SMP
seq_printf(p, "%10u ", irq_stats(j)->irq_call_count);
seq_puts(p, " Function call interrupts\n");
#endif
+ seq_printf(p, "%*s: ", prec, "UAH");
+ for_each_online_cpu(j)
+ seq_printf(p, "%10u ", irq_stats(j)->irq_unaligned_count);
+ seq_puts(p, " Unaligned access handler traps\n");
+ seq_printf(p, "%*s: ", prec, "FPA");
+ for_each_online_cpu(j)
+ seq_printf(p, "%10u ", irq_stats(j)->irq_fpassist_count);
+ seq_puts(p, " Floating point assist traps\n");
seq_printf(p, "%*s: ", prec, "TLB");
for_each_online_cpu(j)
seq_printf(p, "%10u ", irq_stats(j)->irq_tlb_count);
return (BITS_PER_LONG - bit) + TIMER_IRQ;
}
+#ifdef CONFIG_IRQSTACKS
+/*
+ * IRQ STACK - used for irq handler
+ */
+#define IRQ_STACK_SIZE (4096 << 2) /* 16k irq stack size */
+
+union irq_stack_union {
+ unsigned long stack[IRQ_STACK_SIZE/sizeof(unsigned long)];
+ volatile unsigned int slock[4];
+ volatile unsigned int lock[1];
+};
+
+DEFINE_PER_CPU(union irq_stack_union, irq_stack_union) = {
+ .slock = { 1,1,1,1 },
+ };
+#endif
+
+
int sysctl_panic_on_stackoverflow = 1;
static inline void stack_overflow_check(struct pt_regs *regs)
}
#ifdef CONFIG_IRQSTACKS
-DEFINE_PER_CPU(union irq_stack_union, irq_stack_union) = {
- .lock = __RAW_SPIN_LOCK_UNLOCKED((irq_stack_union).lock)
- };
+/* in entry.S: */
+void call_on_stack(unsigned long p1, void *func, unsigned long new_stack);
static void execute_on_irq_stack(void *func, unsigned long param1)
{
union irq_stack_union *union_ptr;
unsigned long irq_stack;
- raw_spinlock_t *irq_stack_in_use;
+ volatile unsigned int *irq_stack_in_use;
union_ptr = &per_cpu(irq_stack_union, smp_processor_id());
irq_stack = (unsigned long) &union_ptr->stack;
- irq_stack = ALIGN(irq_stack + sizeof(irq_stack_union.lock),
+ irq_stack = ALIGN(irq_stack + sizeof(irq_stack_union.slock),
64); /* align for stack frame usage */
/* We may be called recursive. If we are already using the irq stack,
* just continue to use it. Use spinlocks to serialize
* the irq stack usage.
*/
- irq_stack_in_use = &union_ptr->lock;
- if (!raw_spin_trylock(irq_stack_in_use)) {
+ irq_stack_in_use = (volatile unsigned int *)__ldcw_align(union_ptr);
+ if (!__ldcw(irq_stack_in_use)) {
void (*direct_call)(unsigned long p1) = func;
/* We are using the IRQ stack already.
/* This is where we switch to the IRQ stack. */
call_on_stack(param1, func, irq_stack);
- __inc_irq_stat(irq_stack_counter);
-
/* free up irq stack usage. */
- do_raw_spin_unlock(irq_stack_in_use);
+ *irq_stack_in_use = 1;
}
asmlinkage void do_softirq(void)
convert_phys_for_tlb_insert20 %r26 /* convert phys addr to tlb insert format */
convert_phys_for_tlb_insert20 %r23 /* convert phys addr to tlb insert format */
depd %r24,63,22, %r28 /* Form aliased virtual address 'to' */
- depdi 0, 63,PAGE_SHIFT, %r28 /* Clear any offset bits */
+ depdi 0, 63,PAGE_SHIFT, %r28 /* Clear any offset bits */
copy %r28, %r29
depdi 1, 41,1, %r29 /* Form aliased virtual address 'from' */
#else
extrw,u %r26, 24,25, %r26 /* convert phys addr to tlb insert format */
extrw,u %r23, 24,25, %r23 /* convert phys addr to tlb insert format */
depw %r24, 31,22, %r28 /* Form aliased virtual address 'to' */
- depwi 0, 31,12, %r28 /* Clear any offset bits */
+ depwi 0, 31,PAGE_SHIFT, %r28 /* Clear any offset bits */
copy %r28, %r29
depwi 1, 9,1, %r29 /* Form aliased virtual address 'from' */
#endif
#else
extrw,u %r26, 24,25, %r26 /* convert phys addr to tlb insert format */
depw %r25, 31,22, %r28 /* Form aliased virtual address 'to' */
- depwi 0, 31,12, %r28 /* Clear any offset bits */
+ depwi 0, 31,PAGE_SHIFT, %r28 /* Clear any offset bits */
#endif
/* Purge any old translation */
#else
extrw,u %r26, 24,25, %r26 /* convert phys addr to tlb insert format */
depw %r25, 31,22, %r28 /* Form aliased virtual address 'to' */
- depwi 0, 31,12, %r28 /* Clear any offset bits */
+ depwi 0, 31,PAGE_SHIFT, %r28 /* Clear any offset bits */
#endif
/* Purge any old translation */
#endif
convert_phys_for_tlb_insert20 %r26 /* convert phys addr to tlb insert format */
depd %r25, 63,22, %r28 /* Form aliased virtual address 'to' */
- depdi 0, 63,PAGE_SHIFT, %r28 /* Clear any offset bits */
+ depdi 0, 63,PAGE_SHIFT, %r28 /* Clear any offset bits */
#else
extrw,u %r26, 24,25, %r26 /* convert phys addr to tlb insert format */
depw %r25, 31,22, %r28 /* Form aliased virtual address 'to' */
- depwi 0, 31,12, %r28 /* Clear any offset bits */
+ depwi 0, 31,PAGE_SHIFT, %r28 /* Clear any offset bits */
#endif
/* Purge any old translation */
/* called from hpux boot loader */
boot_command_line[0] = '\0';
} else {
- strcpy(boot_command_line, (char *)__va(boot_args[1]));
+ strlcpy(boot_command_line, (char *)__va(boot_args[1]),
+ COMMAND_LINE_SIZE);
#ifdef CONFIG_BLK_DEV_INITRD
if (boot_args[2] != 0) /* did palo pass us a ramdisk? */
case 14:
/* Assist Exception Trap, i.e. floating point exception. */
die_if_kernel("Floating point exception", regs, 0); /* quiet */
+ __inc_irq_stat(irq_fpassist_count);
handle_fpe(regs);
return;
#include <linux/signal.h>
#include <linux/ratelimit.h>
#include <asm/uaccess.h>
+#include <asm/hardirq.h>
/* #define DEBUG_UNALIGNED 1 */
struct siginfo si;
register int flop=0; /* true if this is a flop */
+ __inc_irq_stat(irq_unaligned_count);
+
/* log a message with pacing */
if (user_mode(regs)) {
if (current->thread.flags & PARISC_UAC_SIGBUS) {
CONFIG_USB_HIDDEV=y
CONFIG_USB=m
CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
-CONFIG_USB_SUSPEND=y
CONFIG_USB_MON=m
CONFIG_USB_EHCI_HCD=m
# CONFIG_USB_EHCI_HCD_PPC_OF is not set
#define H_GET_MPP 0x2D4
#define H_HOME_NODE_ASSOCIATIVITY 0x2EC
#define H_BEST_ENERGY 0x2F4
+#define H_XIRR_X 0x2FC
#define H_RANDOM 0x300
#define H_COP 0x304
#define H_GET_MPP_X 0x314
/* Get the pointer to a device_node's pci_dn */
#define PCI_DN(dn) ((struct pci_dn *) (dn)->data)
+extern struct pci_dn *pci_get_pdn(struct pci_dev *pdev);
+
extern void * update_dn_pci_info(struct device_node *dn, void *data);
static inline int pci_device_from_OF_node(struct device_node *np,
#define PPC440EP_ERR42
#endif
+/* The following stops all load and store data streams associated with stream
+ * ID (ie. streams created explicitly). The embedded and server mnemonics for
+ * dcbt are different so we use machine "power4" here explicitly.
+ */
+#define DCBT_STOP_ALL_STREAM_IDS(scratch) \
+.machine push ; \
+.machine "power4" ; \
+ lis scratch,0x60000000@h; \
+ dcbt r0,scratch,0b01010; \
+.machine pop
+
/*
* toreal/fromreal/tophys/tovirt macros. 32-bit BookE makes them
* keep the address intact to be compatible with code shared with
unsigned long ebbrr;
unsigned long ebbhr;
unsigned long bescr;
+ unsigned long siar;
+ unsigned long sdar;
+ unsigned long sier;
+ unsigned long mmcr0;
+ unsigned long mmcr2;
+ unsigned long mmcra;
#endif
};
#endif
#ifdef CONFIG_PPC64
-static inline unsigned long get_clean_sp(struct pt_regs *regs, int is_32)
+static inline unsigned long get_clean_sp(unsigned long sp, int is_32)
{
- unsigned long sp;
-
if (is_32)
- sp = regs->gpr[1] & 0x0ffffffffUL;
- else
- sp = regs->gpr[1];
-
+ return sp & 0x0ffffffffUL;
return sp;
}
#else
-static inline unsigned long get_clean_sp(struct pt_regs *regs, int is_32)
+static inline unsigned long get_clean_sp(unsigned long sp, int is_32)
{
- return regs->gpr[1];
+ return sp;
}
#endif
#define MSR_TM_TRANSACTIONAL(x) (((x) & MSR_TS_MASK) == MSR_TS_T)
#define MSR_TM_SUSPENDED(x) (((x) & MSR_TS_MASK) == MSR_TS_S)
-/* Reason codes describing kernel causes for transaction aborts. By
- convention, bit0 is copied to TEXASR[56] (IBM bit 7) which is set if
- the failure is persistent.
-*/
-#define TM_CAUSE_RESCHED 0xfe
-#define TM_CAUSE_TLBI 0xfc
-#define TM_CAUSE_FAC_UNAV 0xfa
-#define TM_CAUSE_SYSCALL 0xf9 /* Persistent */
-#define TM_CAUSE_MISC 0xf6
-#define TM_CAUSE_SIGNAL 0xf4
-
#if defined(CONFIG_PPC_BOOK3S_64)
#define MSR_64BIT MSR_SF
#define __ARCH_HAS_SA_RESTORER
#include <uapi/asm/signal.h>
+#include <uapi/asm/ptrace.h>
+
+extern unsigned long get_tm_stackpointer(struct pt_regs *regs);
#endif /* _ASM_POWERPC_SIGNAL_H */
* Copyright 2012 Matt Evans & Michael Neuling, IBM Corporation.
*/
+#include <uapi/asm/tm.h>
+
#ifdef CONFIG_PPC_TRANSACTIONAL_MEM
extern void do_load_up_transact_fpu(struct thread_struct *thread);
extern void do_load_up_transact_altivec(struct thread_struct *thread);
header-y += swab.h
header-y += termbits.h
header-y += termios.h
+header-y += tm.h
header-y += types.h
header-y += ucontext.h
header-y += unistd.h
--- /dev/null
+#ifndef _ASM_POWERPC_TM_H
+#define _ASM_POWERPC_TM_H
+
+/* Reason codes describing kernel causes for transaction aborts. By
+ * convention, bit0 is copied to TEXASR[56] (IBM bit 7) which is set if
+ * the failure is persistent. PAPR saves 0xff-0xe0 for the hypervisor.
+ */
+#define TM_CAUSE_PERSISTENT 0x01
+#define TM_CAUSE_RESCHED 0xde
+#define TM_CAUSE_TLBI 0xdc
+#define TM_CAUSE_FAC_UNAV 0xda
+#define TM_CAUSE_SYSCALL 0xd8 /* future use */
+#define TM_CAUSE_MISC 0xd6 /* future use */
+#define TM_CAUSE_SIGNAL 0xd4
+#define TM_CAUSE_ALIGNMENT 0xd2
+#define TM_CAUSE_EMULATE 0xd0
+
+#endif
DEFINE(THREAD_BESCR, offsetof(struct thread_struct, bescr));
DEFINE(THREAD_EBBHR, offsetof(struct thread_struct, ebbhr));
DEFINE(THREAD_EBBRR, offsetof(struct thread_struct, ebbrr));
+ DEFINE(THREAD_SIAR, offsetof(struct thread_struct, siar));
+ DEFINE(THREAD_SDAR, offsetof(struct thread_struct, sdar));
+ DEFINE(THREAD_SIER, offsetof(struct thread_struct, sier));
+ DEFINE(THREAD_MMCR0, offsetof(struct thread_struct, mmcr0));
+ DEFINE(THREAD_MMCR2, offsetof(struct thread_struct, mmcr2));
+ DEFINE(THREAD_MMCRA, offsetof(struct thread_struct, mmcra));
#endif
#ifdef CONFIG_PPC_TRANSACTIONAL_MEM
DEFINE(PACATMSCRATCH, offsetof(struct paca_struct, tm_scratch));
blr
__init_TLB:
- /* Clear the TLB */
- li r6,128
+ /*
+ * Clear the TLB using the "IS 3" form of tlbiel instruction
+ * (invalidate by congruence class). P7 has 128 CCs, P8 has 512
+ * so we just always do 512
+ */
+ li r6,512
mtctr r6
li r7,0xc00 /* IS field = 0b11 */
ptesync
.icache_bsize = 128,
.dcache_bsize = 128,
.oprofile_type = PPC_OPROFILE_POWER4,
- .oprofile_cpu_type = "ppc64/ibm-compat-v1",
+ .oprofile_cpu_type = 0,
.cpu_setup = __setup_cpu_power8,
.cpu_restore = __restore_cpu_power8,
.platform = "power8",
.cpu_name = "POWER7+ (raw)",
.cpu_features = CPU_FTRS_POWER7,
.cpu_user_features = COMMON_USER_POWER7,
- .cpu_user_features = COMMON_USER2_POWER7,
+ .cpu_user_features2 = COMMON_USER2_POWER7,
.mmu_features = MMU_FTRS_POWER7,
.icache_bsize = 128,
.dcache_bsize = 128,
.dcache_bsize = 128,
.num_pmcs = 6,
.pmc_type = PPC_PMC_IBM,
- .oprofile_cpu_type = "ppc64/power8",
+ .oprofile_cpu_type = 0,
.oprofile_type = PPC_OPROFILE_POWER4,
.cpu_setup = __setup_cpu_power8,
.cpu_restore = __restore_cpu_power8,
/* check current_thread_info, _TIF_EMULATE_STACK_STORE */
CURRENT_THREAD_INFO(r9, r1)
lwz r8,TI_FLAGS(r9)
- andis. r8,r8,_TIF_EMULATE_STACK_STORE@h
+ andis. r0,r8,_TIF_EMULATE_STACK_STORE@h
beq+ 1f
addi r8,r1,INT_FRAME_SIZE /* Get the kprobed function entry */
std r0, THREAD_EBBHR(r3)
mfspr r0, SPRN_EBBRR
std r0, THREAD_EBBRR(r3)
+
+ /* PMU registers made user read/(write) by EBB */
+ mfspr r0, SPRN_SIAR
+ std r0, THREAD_SIAR(r3)
+ mfspr r0, SPRN_SDAR
+ std r0, THREAD_SDAR(r3)
+ mfspr r0, SPRN_SIER
+ std r0, THREAD_SIER(r3)
+ mfspr r0, SPRN_MMCR0
+ std r0, THREAD_MMCR0(r3)
+ mfspr r0, SPRN_MMCR2
+ std r0, THREAD_MMCR2(r3)
+ mfspr r0, SPRN_MMCRA
+ std r0, THREAD_MMCRA(r3)
END_FTR_SECTION_IFSET(CPU_FTR_ARCH_207S)
#endif
ldarx r6,0,r1
END_FTR_SECTION_IFSET(CPU_FTR_STCX_CHECKS_ADDRESS)
+#ifdef CONFIG_PPC_BOOK3S
+/* Cancel all explict user streams as they will have no use after context
+ * switch and will stop the HW from creating streams itself
+ */
+ DCBT_STOP_ALL_STREAM_IDS(r6)
+#endif
+
addi r6,r4,-THREAD /* Convert THREAD to 'current' */
std r6,PACACURRENT(r13) /* Set new 'current' */
ld r0, THREAD_EBBRR(r4)
mtspr SPRN_EBBRR, r0
+ /* PMU registers made user read/(write) by EBB */
+ ld r0, THREAD_SIAR(r4)
+ mtspr SPRN_SIAR, r0
+ ld r0, THREAD_SDAR(r4)
+ mtspr SPRN_SDAR, r0
+ ld r0, THREAD_SIER(r4)
+ mtspr SPRN_SIER, r0
+ ld r0, THREAD_MMCR0(r4)
+ mtspr SPRN_MMCR0, r0
+ ld r0, THREAD_MMCR2(r4)
+ mtspr SPRN_MMCR2, r0
+ ld r0, THREAD_MMCRA(r4)
+ mtspr SPRN_MMCRA, r0
+
ld r0,THREAD_TAR(r4)
mtspr SPRN_TAR,r0
END_FTR_SECTION_IFSET(CPU_FTR_ARCH_207S)
* ranges. However, some machines (thanks Apple !) tend to split their
* space into lots of small contiguous ranges. So we have to coalesce.
*
- * - We can only cope with all memory ranges having the same offset
- * between CPU addresses and PCI addresses. Unfortunately, some bridges
- * are setup for a large 1:1 mapping along with a small "window" which
- * maps PCI address 0 to some arbitrary high address of the CPU space in
- * order to give access to the ISA memory hole.
- * The way out of here that I've chosen for now is to always set the
- * offset based on the first resource found, then override it if we
- * have a different offset and the previous was set by an ISA hole.
- *
* - Some busses have IO space not starting at 0, which causes trouble with
* the way we do our IO resource renumbering. The code somewhat deals with
* it for 64 bits but I would expect problems on 32 bits.
int rlen;
int pna = of_n_addr_cells(dev);
int np = pna + 5;
- int memno = 0, isa_hole = -1;
+ int memno = 0;
u32 pci_space;
unsigned long long pci_addr, cpu_addr, pci_next, cpu_next, size;
- unsigned long long isa_mb = 0;
struct resource *res;
printk(KERN_INFO "PCI host bridge %s %s ranges:\n",
}
/* Handles ISA memory hole space here */
if (pci_addr == 0) {
- isa_mb = cpu_addr;
- isa_hole = memno;
if (primary || isa_mem_base == 0)
isa_mem_base = cpu_addr;
hose->isa_mem_phys = cpu_addr;
for (i = 0; i < 3; ++i) {
res = &hose->mem_resources[i];
if (!res->flags) {
- printk(KERN_ERR "PCI: Memory resource 0 not set for "
- "host bridge %s (domain %d)\n",
- hose->dn->full_name, hose->global_number);
+ if (i == 0)
+ printk(KERN_ERR "PCI: Memory resource 0 not set for "
+ "host bridge %s (domain %d)\n",
+ hose->dn->full_name, hose->global_number);
continue;
}
offset = hose->mem_offset[i];
}
EXPORT_SYMBOL(pcibus_to_node);
#endif
+
+static void quirk_radeon_32bit_msi(struct pci_dev *dev)
+{
+ struct pci_dn *pdn = pci_get_pdn(dev);
+
+ if (pdn)
+ pdn->force_32bit_msi = 1;
+}
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x68f2, quirk_radeon_32bit_msi);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0xaa68, quirk_radeon_32bit_msi);
#include <asm/ppc-pci.h>
#include <asm/firmware.h>
+struct pci_dn *pci_get_pdn(struct pci_dev *pdev)
+{
+ struct device_node *dn = pci_device_to_OF_node(pdev);
+ if (!dn)
+ return NULL;
+ return PCI_DN(dn);
+}
+
/*
* Traverse_func that inits the PCI fields of the device node.
* NOTE: this *must* be done before read/write config to the device.
#include <asm/uaccess.h>
#include <asm/unistd.h>
#include <asm/debug.h>
+#include <asm/tm.h>
#include "signal.h"
/*
* Allocate space for the signal frame
*/
-void __user * get_sigframe(struct k_sigaction *ka, struct pt_regs *regs,
+void __user * get_sigframe(struct k_sigaction *ka, unsigned long sp,
size_t frame_size, int is_32)
{
unsigned long oldsp, newsp;
/* Default to using normal stack */
- oldsp = get_clean_sp(regs, is_32);
+ oldsp = get_clean_sp(sp, is_32);
/* Check for alt stack */
if ((ka->sa.sa_flags & SA_ONSTACK) &&
user_enter();
}
+
+unsigned long get_tm_stackpointer(struct pt_regs *regs)
+{
+ /* When in an active transaction that takes a signal, we need to be
+ * careful with the stack. It's possible that the stack has moved back
+ * up after the tbegin. The obvious case here is when the tbegin is
+ * called inside a function that returns before a tend. In this case,
+ * the stack is part of the checkpointed transactional memory state.
+ * If we write over this non transactionally or in suspend, we are in
+ * trouble because if we get a tm abort, the program counter and stack
+ * pointer will be back at the tbegin but our in memory stack won't be
+ * valid anymore.
+ *
+ * To avoid this, when taking a signal in an active transaction, we
+ * need to use the stack pointer from the checkpointed state, rather
+ * than the speculated state. This ensures that the signal context
+ * (written tm suspended) will be written below the stack required for
+ * the rollback. The transaction is aborted becuase of the treclaim,
+ * so any memory written between the tbegin and the signal will be
+ * rolled back anyway.
+ *
+ * For signals taken in non-TM or suspended mode, we use the
+ * normal/non-checkpointed stack pointer.
+ */
+
+#ifdef CONFIG_PPC_TRANSACTIONAL_MEM
+ if (MSR_TM_ACTIVE(regs->msr)) {
+ tm_enable();
+ tm_reclaim(¤t->thread, regs->msr, TM_CAUSE_SIGNAL);
+ if (MSR_TM_TRANSACTIONAL(regs->msr))
+ return current->thread.ckpt_regs.gpr[1];
+ }
+#endif
+ return regs->gpr[1];
+}
extern void do_notify_resume(struct pt_regs *regs, unsigned long thread_info_flags);
-extern void __user * get_sigframe(struct k_sigaction *ka, struct pt_regs *regs,
+extern void __user * get_sigframe(struct k_sigaction *ka, unsigned long sp,
size_t frame_size, int is_32);
extern int handle_signal32(unsigned long sig, struct k_sigaction *ka,
{
unsigned long msr = regs->msr;
- /* tm_reclaim rolls back all reg states, updating thread.ckpt_regs,
- * thread.transact_fpr[], thread.transact_vr[], etc.
- */
- tm_enable();
- tm_reclaim(¤t->thread, msr, TM_CAUSE_SIGNAL);
-
/* Make sure floating point registers are stored in regs */
flush_fp_to_thread(current);
/* Set up Signal Frame */
/* Put a Real Time Context onto stack */
- rt_sf = get_sigframe(ka, regs, sizeof(*rt_sf), 1);
+ rt_sf = get_sigframe(ka, get_tm_stackpointer(regs), sizeof(*rt_sf), 1);
addr = rt_sf;
if (unlikely(rt_sf == NULL))
goto badframe;
unsigned long tramp;
/* Set up Signal Frame */
- frame = get_sigframe(ka, regs, sizeof(*frame), 1);
+ frame = get_sigframe(ka, get_tm_stackpointer(regs), sizeof(*frame), 1);
if (unlikely(frame == NULL))
goto badframe;
sc = (struct sigcontext __user *) &frame->sctx;
* As above, but Transactional Memory is in use, so deliver sigcontexts
* containing checkpointed and transactional register states.
*
- * To do this, we treclaim to gather both sets of registers and set up the
- * 'normal' sigcontext registers with rolled-back register values such that a
- * simple signal handler sees a correct checkpointed register state.
- * If interested, a TM-aware sighandler can examine the transactional registers
- * in the 2nd sigcontext to determine the real origin of the signal.
+ * To do this, we treclaim (done before entering here) to gather both sets of
+ * registers and set up the 'normal' sigcontext registers with rolled-back
+ * register values such that a simple signal handler sees a correct
+ * checkpointed register state. If interested, a TM-aware sighandler can
+ * examine the transactional registers in the 2nd sigcontext to determine the
+ * real origin of the signal.
*/
static long setup_tm_sigcontexts(struct sigcontext __user *sc,
struct sigcontext __user *tm_sc,
BUG_ON(!MSR_TM_ACTIVE(regs->msr));
- /* tm_reclaim rolls back all reg states, saving checkpointed (older)
- * GPRs to thread.ckpt_regs and (if used) FPRs to (newer)
- * thread.transact_fp and/or VRs to (newer) thread.transact_vr.
- * THEN we save out FP/VRs, if necessary, to the checkpointed (older)
- * thread.fr[]/vr[]s. The transactional (newer) GPRs are on the
- * stack, in *regs.
- */
- tm_enable();
- tm_reclaim(¤t->thread, msr, TM_CAUSE_SIGNAL);
-
flush_fp_to_thread(current);
#ifdef CONFIG_ALTIVEC
unsigned long newsp = 0;
long err = 0;
- frame = get_sigframe(ka, regs, sizeof(*frame), 0);
+ frame = get_sigframe(ka, get_tm_stackpointer(regs), sizeof(*frame), 0);
if (unlikely(frame == NULL))
goto badframe;
#ifdef CONFIG_PPC64
#include <asm/firmware.h>
#include <asm/processor.h>
+#include <asm/tm.h>
#endif
#include <asm/kexec.h>
#include <asm/ppc-opcode.h>
return 0;
}
+#ifdef CONFIG_PPC_TRANSACTIONAL_MEM
+static inline bool tm_abort_check(struct pt_regs *regs, int cause)
+{
+ /* If we're emulating a load/store in an active transaction, we cannot
+ * emulate it as the kernel operates in transaction suspended context.
+ * We need to abort the transaction. This creates a persistent TM
+ * abort so tell the user what caused it with a new code.
+ */
+ if (MSR_TM_TRANSACTIONAL(regs->msr)) {
+ tm_enable();
+ tm_abort(cause);
+ return true;
+ }
+ return false;
+}
+#else
+static inline bool tm_abort_check(struct pt_regs *regs, int reason)
+{
+ return false;
+}
+#endif
+
static int emulate_instruction(struct pt_regs *regs)
{
u32 instword;
/* Emulate load/store string insn. */
if ((instword & PPC_INST_STRING_GEN_MASK) == PPC_INST_STRING) {
+ if (tm_abort_check(regs,
+ TM_CAUSE_EMULATE | TM_CAUSE_PERSISTENT))
+ return -EINVAL;
PPC_WARN_EMULATED(string, regs);
return emulate_string_inst(regs, instword);
}
if (!arch_irq_disabled_regs(regs))
local_irq_enable();
+ if (tm_abort_check(regs, TM_CAUSE_ALIGNMENT | TM_CAUSE_PERSISTENT))
+ goto bail;
+
/* we don't implement logging of alignment exceptions */
if (!(current->thread.align_ctl & PR_UNALIGN_SIGBUS))
fixed = fix_alignment(regs);
case H_CPPR:
case H_EOI:
case H_IPI:
+ case H_IPOLL:
+ case H_XIRR_X:
if (kvmppc_xics_enabled(vcpu)) {
ret = kvmppc_xics_hcall(vcpu, req);
break;
case H_CPPR:
case H_EOI:
case H_IPI:
+ case H_IPOLL:
+ case H_XIRR_X:
if (kvmppc_xics_enabled(vcpu))
return kvmppc_h_pr_xics_hcall(vcpu, cmd);
break;
return H_SUCCESS;
}
+static int kvmppc_h_ipoll(struct kvm_vcpu *vcpu, unsigned long server)
+{
+ union kvmppc_icp_state state;
+ struct kvmppc_icp *icp;
+
+ icp = vcpu->arch.icp;
+ if (icp->server_num != server) {
+ icp = kvmppc_xics_find_server(vcpu->kvm, server);
+ if (!icp)
+ return H_PARAMETER;
+ }
+ state = ACCESS_ONCE(icp->state);
+ kvmppc_set_gpr(vcpu, 4, ((u32)state.cppr << 24) | state.xisr);
+ kvmppc_set_gpr(vcpu, 5, state.mfrr);
+ return H_SUCCESS;
+}
+
static noinline void kvmppc_h_cppr(struct kvm_vcpu *vcpu, unsigned long cppr)
{
union kvmppc_icp_state old_state, new_state;
if (!xics || !vcpu->arch.icp)
return H_HARDWARE;
+ /* These requests don't have real-mode implementations at present */
+ switch (req) {
+ case H_XIRR_X:
+ res = kvmppc_h_xirr(vcpu);
+ kvmppc_set_gpr(vcpu, 4, res);
+ kvmppc_set_gpr(vcpu, 5, get_tb());
+ return rc;
+ case H_IPOLL:
+ rc = kvmppc_h_ipoll(vcpu, kvmppc_get_gpr(vcpu, 4));
+ return rc;
+ }
+
/* Check for real mode returning too hard */
if (xics->real_mode)
return kvmppc_xics_rm_complete(vcpu, req);
* aligned we don't need to clear the bottom 7 bits of either
* address.
*/
- ori r9,r3,1 /* stream=1 */
+ ori r9,r3,1 /* stream=1 => to */
#ifdef CONFIG_PPC_64K_PAGES
- lis r7,0x0E01 /* depth=7, units=512 */
+ lis r7,0x0E01 /* depth=7
+ * units/cachelines=512 */
#else
lis r7,0x0E00 /* depth=7 */
- ori r7,r7,0x1000 /* units=32 */
+ ori r7,r7,0x1000 /* units/cachelines=32 */
#endif
ori r10,r7,1 /* stream=1 */
.machine push
.machine "power4"
- dcbt r0,r4,0b01000
- dcbt r0,r7,0b01010
- dcbtst r0,r9,0b01000
- dcbtst r0,r10,0b01010
+ /* setup read stream 0 */
+ dcbt r0,r4,0b01000 /* addr from */
+ dcbt r0,r7,0b01010 /* length and depth from */
+ /* setup write stream 1 */
+ dcbtst r0,r9,0b01000 /* addr to */
+ dcbtst r0,r10,0b01010 /* length and depth to */
eieio
- dcbt r0,r8,0b01010 /* GO */
+ dcbt r0,r8,0b01010 /* all streams GO */
.machine pop
#ifdef CONFIG_ALTIVEC
.machine push
.machine "power4"
- dcbt r0,r6,0b01000
- dcbt r0,r7,0b01010
- dcbtst r0,r9,0b01000
- dcbtst r0,r10,0b01010
+ /* setup read stream 0 */
+ dcbt r0,r6,0b01000 /* addr from */
+ dcbt r0,r7,0b01010 /* length and depth from */
+ /* setup write stream 1 */
+ dcbtst r0,r9,0b01000 /* addr to */
+ dcbtst r0,r10,0b01010 /* length and depth to */
eieio
- dcbt r0,r8,0b01010 /* GO */
+ dcbt r0,r8,0b01010 /* all streams GO */
.machine pop
beq cr1,.Lunwind_stack_nonvmx_copy
hpte_v = hptep->v;
actual_psize = hpte_actual_psize(hptep, psize);
+ /*
+ * We need to invalidate the TLB always because hpte_remove doesn't do
+ * a tlb invalidate. If a hash bucket gets full, we "evict" a more/less
+ * random entry from it. When we do that we don't invalidate the TLB
+ * (hpte_remove) because we assume the old translation is still
+ * technically "valid".
+ */
if (actual_psize < 0) {
- native_unlock_hpte(hptep);
- return -1;
+ actual_psize = psize;
+ ret = -1;
+ goto err_out;
}
- /* Even if we miss, we need to invalidate the TLB */
if (!HPTE_V_COMPARE(hpte_v, want_v)) {
DBG_LOW(" -> miss\n");
ret = -1;
hptep->r = (hptep->r & ~(HPTE_R_PP | HPTE_R_N)) |
(newpp & (HPTE_R_PP | HPTE_R_N | HPTE_R_C));
}
+err_out:
native_unlock_hpte(hptep);
/* Ensure it is out of the tlb too. */
hptep = htab_address + slot;
actual_psize = hpte_actual_psize(hptep, psize);
if (actual_psize < 0)
- return;
+ actual_psize = psize;
/* Update the HPTE */
hptep->r = (hptep->r & ~(HPTE_R_PP | HPTE_R_N)) |
hpte_v = hptep->v;
actual_psize = hpte_actual_psize(hptep, psize);
+ /*
+ * We need to invalidate the TLB always because hpte_remove doesn't do
+ * a tlb invalidate. If a hash bucket gets full, we "evict" a more/less
+ * random entry from it. When we do that we don't invalidate the TLB
+ * (hpte_remove) because we assume the old translation is still
+ * technically "valid".
+ */
if (actual_psize < 0) {
+ actual_psize = psize;
native_unlock_hpte(hptep);
- local_irq_restore(flags);
- return;
+ goto err_out;
}
- /* Even if we miss, we need to invalidate the TLB */
if (!HPTE_V_COMPARE(hpte_v, want_v))
native_unlock_hpte(hptep);
else
/* Invalidate the hpte. NOTE: this also unlocks it */
hptep->v = 0;
+err_out:
/* Invalidate the TLB */
tlbie(vpn, psize, actual_psize, ssize, local);
-
local_irq_restore(flags);
}
static bool regs_use_siar(struct pt_regs *regs)
{
- return !!(regs->result & 1);
+ return !!regs->result;
}
/*
* If we're not doing instruction sampling, give them the SDAR
* (sampled data address). If we are doing instruction sampling, then
* only give them the SDAR if it corresponds to the instruction
- * pointed to by SIAR; this is indicated by the [POWER6_]MMCRA_SDSYNC or
- * the [POWER7P_]MMCRA_SDAR_VALID bit in MMCRA.
+ * pointed to by SIAR; this is indicated by the [POWER6_]MMCRA_SDSYNC, the
+ * [POWER7P_]MMCRA_SDAR_VALID bit in MMCRA, or the SDAR_VALID bit in SIER.
*/
static inline void perf_get_data_addr(struct pt_regs *regs, u64 *addrp)
{
unsigned long mmcra = regs->dsisr;
- unsigned long sdsync;
+ bool sdar_valid;
- if (ppmu->flags & PPMU_SIAR_VALID)
- sdsync = POWER7P_MMCRA_SDAR_VALID;
- else if (ppmu->flags & PPMU_ALT_SIPR)
- sdsync = POWER6_MMCRA_SDSYNC;
- else
- sdsync = MMCRA_SDSYNC;
+ if (ppmu->flags & PPMU_HAS_SIER)
+ sdar_valid = regs->dar & SIER_SDAR_VALID;
+ else {
+ unsigned long sdsync;
+
+ if (ppmu->flags & PPMU_SIAR_VALID)
+ sdsync = POWER7P_MMCRA_SDAR_VALID;
+ else if (ppmu->flags & PPMU_ALT_SIPR)
+ sdsync = POWER6_MMCRA_SDSYNC;
+ else
+ sdsync = MMCRA_SDSYNC;
+
+ sdar_valid = mmcra & sdsync;
+ }
- if (!(mmcra & MMCRA_SAMPLE_ENABLE) || (mmcra & sdsync))
+ if (!(mmcra & MMCRA_SAMPLE_ENABLE) || sdar_valid)
*addrp = mfspr(SPRN_SDAR);
}
return !!(regs->dsisr & sipr);
}
-static bool regs_no_sipr(struct pt_regs *regs)
-{
- return !!(regs->result & 2);
-}
-
static inline u32 perf_flags_from_msr(struct pt_regs *regs)
{
if (regs->msr & MSR_PR)
* SIAR which should give slightly more reliable
* results
*/
- if (regs_no_sipr(regs)) {
+ if (ppmu->flags & PPMU_NO_SIPR) {
unsigned long siar = mfspr(SPRN_SIAR);
if (siar >= PAGE_OFFSET)
return PERF_RECORD_MISC_KERNEL;
int use_siar;
regs->dsisr = mmcra;
- regs->result = 0;
-
- if (ppmu->flags & PPMU_NO_SIPR)
- regs->result |= 2;
-
- /*
- * On power8 if we're in random sampling mode, the SIER is updated.
- * If we're in continuous sampling mode, we don't have SIPR.
- */
- if (ppmu->flags & PPMU_HAS_SIER) {
- if (marked)
- regs->dar = mfspr(SPRN_SIER);
- else
- regs->result |= 2;
- }
+ if (ppmu->flags & PPMU_HAS_SIER)
+ regs->dar = mfspr(SPRN_SIER);
/*
* If this isn't a PMU exception (eg a software event) the SIAR is
use_siar = 1;
else if ((ppmu->flags & PPMU_NO_CONT_SAMPLING))
use_siar = 0;
- else if (!regs_no_sipr(regs) && regs_sipr(regs))
+ else if (!(ppmu->flags & PPMU_NO_SIPR) && regs_sipr(regs))
use_siar = 0;
else
use_siar = 1;
- regs->result |= use_siar;
+ regs->result = use_siar;
}
/*
unsigned long mmcra = regs->dsisr;
int marked = mmcra & MMCRA_SAMPLE_ENABLE;
- if ((ppmu->flags & PPMU_SIAR_VALID) && marked)
- return mmcra & POWER7P_MMCRA_SIAR_VALID;
+ if (marked) {
+ if (ppmu->flags & PPMU_HAS_SIER)
+ return regs->dar & SIER_SIAR_VALID;
+
+ if (ppmu->flags & PPMU_SIAR_VALID)
+ return mmcra & POWER7P_MMCRA_SIAR_VALID;
+ }
return 1;
}
select PPC_ICP_NATIVE
select PPC_P7_NAP
select PPC_PCI_CHOICE if EMBEDDED
+ select EPAPR_BOOT
default y
config POWERNV_MSI
define_pe_printk_level(pe_warn, KERN_WARNING);
define_pe_printk_level(pe_info, KERN_INFO);
-static struct pci_dn *pnv_ioda_get_pdn(struct pci_dev *dev)
-{
- struct device_node *np;
-
- np = pci_device_to_OF_node(dev);
- if (!np)
- return NULL;
- return PCI_DN(np);
-}
-
static int pnv_ioda_alloc_pe(struct pnv_phb *phb)
{
unsigned long pe;
{
struct pci_controller *hose = pci_bus_to_host(dev->bus);
struct pnv_phb *phb = hose->private_data;
- struct pci_dn *pdn = pnv_ioda_get_pdn(dev);
+ struct pci_dn *pdn = pci_get_pdn(dev);
if (!pdn)
return NULL;
/* Add to all parents PELT-V */
while (parent) {
- struct pci_dn *pdn = pnv_ioda_get_pdn(parent);
+ struct pci_dn *pdn = pci_get_pdn(parent);
if (pdn && pdn->pe_number != IODA_INVALID_PE) {
rc = opal_pci_set_peltv(phb->opal_id, pdn->pe_number,
pe->pe_number, OPAL_ADD_PE_TO_DOMAIN);
{
struct pci_controller *hose = pci_bus_to_host(dev->bus);
struct pnv_phb *phb = hose->private_data;
- struct pci_dn *pdn = pnv_ioda_get_pdn(dev);
+ struct pci_dn *pdn = pci_get_pdn(dev);
struct pnv_ioda_pe *pe;
int pe_num;
struct pci_dev *dev;
list_for_each_entry(dev, &bus->devices, bus_list) {
- struct pci_dn *pdn = pnv_ioda_get_pdn(dev);
+ struct pci_dn *pdn = pci_get_pdn(dev);
if (pdn == NULL) {
pr_warn("%s: No device node associated with device !\n",
static void pnv_pci_ioda_dma_dev_setup(struct pnv_phb *phb, struct pci_dev *pdev)
{
- struct pci_dn *pdn = pnv_ioda_get_pdn(pdev);
+ struct pci_dn *pdn = pci_get_pdn(pdev);
struct pnv_ioda_pe *pe;
/*
unsigned int is_64, struct msi_msg *msg)
{
struct pnv_ioda_pe *pe = pnv_ioda_get_pe(dev);
+ struct pci_dn *pdn = pci_get_pdn(dev);
struct irq_data *idata;
struct irq_chip *ichip;
unsigned int xive_num = hwirq - phb->msi_base;
if (pe->mve_number < 0)
return -ENXIO;
+ /* Force 32-bit MSI on some broken devices */
+ if (pdn && pdn->force_32bit_msi)
+ is_64 = 0;
+
/* Assign XIVE to PE */
rc = opal_pci_set_xive_pe(phb->opal_id, pe->pe_number, xive_num);
if (rc) {
if (!phb->initialized)
return 0;
- pdn = pnv_ioda_get_pdn(dev);
+ pdn = pci_get_pdn(dev);
if (!pdn || pdn->pe_number == IODA_INVALID_PE)
return -EINVAL;
{
struct pci_controller *hose = pci_bus_to_host(pdev->bus);
struct pnv_phb *phb = hose->private_data;
+ struct pci_dn *pdn = pci_get_pdn(pdev);
+
+ if (pdn && pdn->force_32bit_msi && !phb->msi32_support)
+ return -ENODEV;
return (phb && phb->msi_bmp.bitmap) ? 0 : -ENODEV;
}
while (npages--)
*(tcep++) = 0;
- if (tbl->it_type & TCE_PCI_SWINV_CREATE)
+ if (tbl->it_type & TCE_PCI_SWINV_FREE)
pnv_pci_ioda_tce_invalidate(tbl, tces, tcep - 1);
}
select ZLIB_DEFLATE
select PPC_DOORBELL
select HAVE_CONTEXT_TRACKING
+ select HOTPLUG if SMP
+ select HOTPLUG_CPU if SMP
default y
config PPC_SPLPAR
#define RTAS_CHANGE_MSIX_FN 4
#define RTAS_CHANGE_32MSI_FN 5
-static struct pci_dn *get_pdn(struct pci_dev *pdev)
-{
- struct device_node *dn;
- struct pci_dn *pdn;
-
- dn = pci_device_to_OF_node(pdev);
- if (!dn) {
- dev_dbg(&pdev->dev, "rtas_msi: No OF device node\n");
- return NULL;
- }
-
- pdn = PCI_DN(dn);
- if (!pdn) {
- dev_dbg(&pdev->dev, "rtas_msi: No PCI DN\n");
- return NULL;
- }
-
- return pdn;
-}
-
/* RTAS Helpers */
static int rtas_change_msi(struct pci_dn *pdn, u32 func, u32 num_irqs)
{
struct pci_dn *pdn;
- pdn = get_pdn(pdev);
+ pdn = pci_get_pdn(pdev);
if (!pdn)
return;
struct pci_dn *pdn;
const u32 *req_msi;
- pdn = get_pdn(pdev);
+ pdn = pci_get_pdn(pdev);
if (!pdn)
return -ENODEV;
return 0;
}
+static void rtas_hack_32bit_msi_gen2(struct pci_dev *pdev)
+{
+ u32 addr_hi, addr_lo;
+
+ /*
+ * We should only get in here for IODA1 configs. This is based on the
+ * fact that we using RTAS for MSIs, we don't have the 32 bit MSI RTAS
+ * support, and we are in a PCIe Gen2 slot.
+ */
+ dev_info(&pdev->dev,
+ "rtas_msi: No 32 bit MSI firmware support, forcing 32 bit MSI\n");
+ pci_read_config_dword(pdev, pdev->msi_cap + PCI_MSI_ADDRESS_HI, &addr_hi);
+ addr_lo = 0xffff0000 | ((addr_hi >> (48 - 32)) << 4);
+ pci_write_config_dword(pdev, pdev->msi_cap + PCI_MSI_ADDRESS_LO, addr_lo);
+ pci_write_config_dword(pdev, pdev->msi_cap + PCI_MSI_ADDRESS_HI, 0);
+}
+
static int rtas_setup_msi_irqs(struct pci_dev *pdev, int nvec_in, int type)
{
struct pci_dn *pdn;
struct msi_desc *entry;
struct msi_msg msg;
int nvec = nvec_in;
+ int use_32bit_msi_hack = 0;
- pdn = get_pdn(pdev);
+ pdn = pci_get_pdn(pdev);
if (!pdn)
return -ENODEV;
*/
again:
if (type == PCI_CAP_ID_MSI) {
- if (pdn->force_32bit_msi)
+ if (pdn->force_32bit_msi) {
rc = rtas_change_msi(pdn, RTAS_CHANGE_32MSI_FN, nvec);
- else
+ if (rc < 0) {
+ /*
+ * We only want to run the 32 bit MSI hack below if
+ * the max bus speed is Gen2 speed
+ */
+ if (pdev->bus->max_bus_speed != PCIE_SPEED_5_0GT)
+ return rc;
+
+ use_32bit_msi_hack = 1;
+ }
+ } else
+ rc = -1;
+
+ if (rc < 0)
rc = rtas_change_msi(pdn, RTAS_CHANGE_MSI_FN, nvec);
- if (rc < 0 && !pdn->force_32bit_msi) {
+ if (rc < 0) {
pr_debug("rtas_msi: trying the old firmware call.\n");
rc = rtas_change_msi(pdn, RTAS_CHANGE_FN, nvec);
}
+
+ if (use_32bit_msi_hack && rc > 0)
+ rtas_hack_32bit_msi_gen2(pdev);
} else
rc = rtas_change_msi(pdn, RTAS_CHANGE_MSIX_FN, nvec);
}
arch_initcall(rtas_msi_init);
-static void quirk_radeon(struct pci_dev *dev)
-{
- struct pci_dn *pdn = get_pdn(dev);
-
- if (pdn)
- pdn->force_32bit_msi = 1;
-}
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x68f2, quirk_radeon);
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0xaa68, quirk_radeon);
#ifdef CONFIG_PPC32 /* XXX for now */
#ifdef CONFIG_IRQ_ALL_CPUS
-#define distribute_irqs (!(mpic->flags & MPIC_SINGLE_DEST_CPU))
+#define distribute_irqs (1)
#else
#define distribute_irqs (0)
#endif
* it differently, then we should make sure we also change the default
* values of irq_desc[].affinity in irq.c.
*/
- if (distribute_irqs) {
+ if (distribute_irqs && !(mpic->flags & MPIC_SINGLE_DEST_CPU)) {
for (i = 0; i < mpic->num_sources ; i++)
mpic_irq_write(i, MPIC_INFO(IRQ_DESTINATION),
mpic_irq_read(i, MPIC_INFO(IRQ_DESTINATION)) | msk);
return 0;
}
if (!write) {
- len = sprintf(buf, appldata_timer_active ? "1\n" : "0\n");
+ strncpy(buf, appldata_timer_active ? "1\n" : "0\n",
+ ARRAY_SIZE(buf));
+ len = strnlen(buf, ARRAY_SIZE(buf));
if (len > *lenp)
len = *lenp;
if (copy_to_user(buffer, buf, len))
return 0;
}
if (!write) {
- len = sprintf(buf, ops->active ? "1\n" : "0\n");
+ strncpy(buf, ops->active ? "1\n" : "0\n", ARRAY_SIZE(buf));
+ len = strnlen(buf, ARRAY_SIZE(buf));
if (len > *lenp)
len = *lenp;
if (copy_to_user(buffer, buf, len)) {
{
struct dma_map_ops *dma_ops = get_dma_ops(dev);
- dma_ops->free(dev, size, cpu_addr, dma_handle, NULL);
debug_dma_free_coherent(dev, size, cpu_addr, dma_handle);
+ dma_ops->free(dev, size, cpu_addr, dma_handle, NULL);
}
#endif /* _ASM_S390_DMA_MAPPING_H */
}
void *xlate_dev_mem_ptr(unsigned long phys);
+#define xlate_dev_mem_ptr xlate_dev_mem_ptr
void unxlate_dev_mem_ptr(unsigned long phys, void *addr);
/*
unsigned long address, bits;
unsigned char skey;
- if (!pte_present(*ptep))
+ if (pte_val(*ptep) & _PAGE_INVALID)
return pgste;
address = pte_val(*ptep) & PAGE_MASK;
skey = page_get_storage_key(address);
#ifdef CONFIG_PGSTE
int young;
- if (!pte_present(*ptep))
+ if (pte_val(*ptep) & _PAGE_INVALID)
return pgste;
/* Get referenced bit from storage key */
young = page_reset_referenced(pte_val(*ptep) & PAGE_MASK);
unsigned long address;
unsigned long okey, nkey;
- if (!pte_present(entry))
+ if (pte_val(entry) & _PAGE_INVALID)
return;
address = pte_val(entry) & PAGE_MASK;
okey = nkey = page_get_storage_key(address);
pte = *ptep;
if (!mm_exclusive(mm))
__ptep_ipte(address, ptep);
+
+ if (mm_has_pgste(mm))
+ pgste = pgste_update_all(&pte, pgste);
return pte;
}
unsigned long address,
pte_t *ptep, pte_t pte)
{
+ pgste_t pgste;
+
if (mm_has_pgste(mm)) {
+ pgste = *(pgste_t *)(ptep + PTRS_PER_PTE);
+ pgste_set_key(ptep, pgste, pte);
pgste_set_pte(ptep, pte);
- pgste_set_unlock(ptep, *(pgste_t *)(ptep + PTRS_PER_PTE));
+ pgste_set_unlock(ptep, pgste);
} else
*ptep = pte;
}
* This is the main routine where commands issued by other
* cpus are handled.
*/
-static void do_ext_call_interrupt(struct ext_code ext_code,
- unsigned int param32, unsigned long param64)
+static void smp_handle_ext_call(void)
{
unsigned long bits;
- int cpu;
-
- cpu = smp_processor_id();
- if (ext_code.code == 0x1202)
- inc_irq_stat(IRQEXT_EXC);
- else
- inc_irq_stat(IRQEXT_EMS);
- /*
- * handle bit signal external calls
- */
- bits = xchg(&pcpu_devices[cpu].ec_mask, 0);
+ /* handle bit signal external calls */
+ bits = xchg(&pcpu_devices[smp_processor_id()].ec_mask, 0);
if (test_bit(ec_stop_cpu, &bits))
smp_stop_cpu();
-
if (test_bit(ec_schedule, &bits))
scheduler_ipi();
-
if (test_bit(ec_call_function, &bits))
generic_smp_call_function_interrupt();
-
if (test_bit(ec_call_function_single, &bits))
generic_smp_call_function_single_interrupt();
+}
+static void do_ext_call_interrupt(struct ext_code ext_code,
+ unsigned int param32, unsigned long param64)
+{
+ inc_irq_stat(ext_code.code == 0x1202 ? IRQEXT_EXC : IRQEXT_EMS);
+ smp_handle_ext_call();
}
void arch_send_call_function_ipi_mask(const struct cpumask *mask)
{
unsigned long cregs[16];
+ /* Handle possible pending IPIs */
+ smp_handle_ext_call();
set_cpu_online(smp_processor_id(), false);
/* Disable pseudo page faults on this cpu. */
pfault_fini();
mp = (struct gmap_pgtable *) page->index;
rmap->gmap = gmap;
rmap->entry = segment_ptr;
- rmap->vmaddr = address;
+ rmap->vmaddr = address & PMD_MASK;
spin_lock(&mm->page_table_lock);
if (*segment_ptr == segment) {
list_add(&rmap->list, &mp->mapper);
unsigned long empty_zero_page;
EXPORT_SYMBOL_GPL(empty_zero_page);
-static struct kcore_list kcore_mem, kcore_vmalloc;
-
static void setup_zero_page(void)
{
struct page *page;
pand %xmm3, %xmm1
PCLMULQDQ 0x00, CONSTANT, %xmm1
pxor %xmm2, %xmm1
- pextrd $0x01, %xmm1, %eax
+ PEXTRD 0x01, %xmm1, %eax
ret
ENDPROC(crc32_pclmul_le_16)
_INP_END_SIZE = 8
_INP_SIZE = 8
-_XFER_SIZE = 8
+_XFER_SIZE = 16
_XMM_SAVE_SIZE = 0
_INP_END = 0
_INP_END_SIZE = 8
_INP_SIZE = 8
-_XFER_SIZE = 8
+_XFER_SIZE = 16
_XMM_SAVE_SIZE = 0
_INP_END = 0
#define REG_NUM_INVALID 100
-#define REG_TYPE_R64 0
-#define REG_TYPE_XMM 1
+#define REG_TYPE_R32 0
+#define REG_TYPE_R64 1
+#define REG_TYPE_XMM 2
#define REG_TYPE_INVALID 100
+ .macro R32_NUM opd r32
+ \opd = REG_NUM_INVALID
+ .ifc \r32,%eax
+ \opd = 0
+ .endif
+ .ifc \r32,%ecx
+ \opd = 1
+ .endif
+ .ifc \r32,%edx
+ \opd = 2
+ .endif
+ .ifc \r32,%ebx
+ \opd = 3
+ .endif
+ .ifc \r32,%esp
+ \opd = 4
+ .endif
+ .ifc \r32,%ebp
+ \opd = 5
+ .endif
+ .ifc \r32,%esi
+ \opd = 6
+ .endif
+ .ifc \r32,%edi
+ \opd = 7
+ .endif
+#ifdef CONFIG_X86_64
+ .ifc \r32,%r8d
+ \opd = 8
+ .endif
+ .ifc \r32,%r9d
+ \opd = 9
+ .endif
+ .ifc \r32,%r10d
+ \opd = 10
+ .endif
+ .ifc \r32,%r11d
+ \opd = 11
+ .endif
+ .ifc \r32,%r12d
+ \opd = 12
+ .endif
+ .ifc \r32,%r13d
+ \opd = 13
+ .endif
+ .ifc \r32,%r14d
+ \opd = 14
+ .endif
+ .ifc \r32,%r15d
+ \opd = 15
+ .endif
+#endif
+ .endm
+
.macro R64_NUM opd r64
\opd = REG_NUM_INVALID
+#ifdef CONFIG_X86_64
.ifc \r64,%rax
\opd = 0
.endif
.ifc \r64,%r15
\opd = 15
.endif
+#endif
.endm
.macro XMM_NUM opd xmm
.endm
.macro REG_TYPE type reg
+ R32_NUM reg_type_r32 \reg
R64_NUM reg_type_r64 \reg
XMM_NUM reg_type_xmm \reg
.if reg_type_r64 <> REG_NUM_INVALID
\type = REG_TYPE_R64
+ .elseif reg_type_r32 <> REG_NUM_INVALID
+ \type = REG_TYPE_R32
.elseif reg_type_xmm <> REG_NUM_INVALID
\type = REG_TYPE_XMM
.else
.byte \imm8
.endm
+ .macro PEXTRD imm8 xmm gpr
+ R32_NUM extrd_opd1 \gpr
+ XMM_NUM extrd_opd2 \xmm
+ PFX_OPD_SIZE
+ PFX_REX extrd_opd1 extrd_opd2
+ .byte 0x0f, 0x3a, 0x16
+ MODRM 0xc0 extrd_opd1 extrd_opd2
+ .byte \imm8
+ .endm
+
.macro AESKEYGENASSIST rcon xmm1 xmm2
XMM_NUM aeskeygen_opd1 \xmm1
XMM_NUM aeskeygen_opd2 \xmm2
movq %rdi, %rax
shrq $PUD_SHIFT, %rax
andl $(PTRS_PER_PUD-1), %eax
- movq %rdx, (4096+0)(%rbx,%rax,8)
- movq %rdx, (4096+8)(%rbx,%rax,8)
+ movq %rdx, 4096(%rbx,%rax,8)
+ incl %eax
+ andl $(PTRS_PER_PUD-1), %eax
+ movq %rdx, 4096(%rbx,%rax,8)
addq $8192, %rbx
movq %rdi, %rax
/*
* Were we in an interrupt that interrupted kernel mode?
*
- * For now, with eagerfpu we will return interrupted kernel FPU
- * state as not-idle. TBD: Ideally we can change the return value
- * to something like __thread_has_fpu(current). But we need to
- * be careful of doing __thread_clear_has_fpu() before saving
- * the FPU etc for supporting nested uses etc. For now, take
- * the simple route!
- *
* On others, we can do a kernel_fpu_begin/end() pair *ONLY* if that
* pair does nothing at all: the thread must not have fpu (so
* that we don't try to save the FPU state), and TS must
* be set (so that the clts/stts pair does nothing that is
* visible in the interrupted kernel thread).
+ *
+ * Except for the eagerfpu case when we return 1 unless we've already
+ * been eager and saved the state in kernel_fpu_begin().
*/
static inline bool interrupted_kernel_fpu_idle(void)
{
if (use_eager_fpu())
- return 0;
+ return __thread_has_fpu(current);
return !__thread_has_fpu(current) &&
(read_cr0() & X86_CR0_TS);
struct task_struct *me = current;
if (__thread_has_fpu(me)) {
- __save_init_fpu(me);
__thread_clear_has_fpu(me);
+ __save_init_fpu(me);
/* We do 'stts()' in __kernel_fpu_end() */
} else if (!use_eager_fpu()) {
this_cpu_write(fpu_owner_task, NULL);
ctxt->modrm_seg = VCPU_SREG_DS;
if (ctxt->modrm_mod == 3) {
+ int highbyte_regs = ctxt->rex_prefix == 0;
+
op->type = OP_REG;
op->bytes = (ctxt->d & ByteOp) ? 1 : ctxt->op_bytes;
- op->addr.reg = decode_register(ctxt, ctxt->modrm_rm, ctxt->d & ByteOp);
+ op->addr.reg = decode_register(ctxt, ctxt->modrm_rm,
+ highbyte_regs && (ctxt->d & ByteOp));
if (ctxt->d & Sse) {
op->type = OP_XMM;
op->bytes = 16;
DI(ImplicitOps | Priv, invd), DI(ImplicitOps | Priv, wbinvd), N, N,
N, D(ImplicitOps | ModRM), N, N,
/* 0x10 - 0x1F */
- N, N, N, N, N, N, N, N, D(ImplicitOps | ModRM), N, N, N, N, N, N, N,
+ N, N, N, N, N, N, N, N,
+ D(ImplicitOps | ModRM), N, N, N, N, N, N, D(ImplicitOps | ModRM),
/* 0x20 - 0x2F */
DIP(ModRM | DstMem | Priv | Op3264, cr_read, check_cr_read),
DIP(ModRM | DstMem | Priv | Op3264, dr_read, check_dr_read),
case 0x08: /* invd */
case 0x0d: /* GrpP (prefetch) */
case 0x18: /* Grp16 (prefetch/nop) */
+ case 0x1f: /* nop */
break;
case 0x20: /* mov cr, reg */
ctxt->dst.val = ops->get_cr(ctxt, ctxt->modrm_reg);
{
struct kvm_lapic *apic = vcpu->arch.apic;
unsigned int sipi_vector;
+ unsigned long pe;
- if (!kvm_vcpu_has_lapic(vcpu))
+ if (!kvm_vcpu_has_lapic(vcpu) || !apic->pending_events)
return;
- if (test_and_clear_bit(KVM_APIC_INIT, &apic->pending_events)) {
+ pe = xchg(&apic->pending_events, 0);
+
+ if (test_bit(KVM_APIC_INIT, &pe)) {
kvm_lapic_reset(vcpu);
kvm_vcpu_reset(vcpu);
if (kvm_vcpu_is_bsp(apic->vcpu))
else
vcpu->arch.mp_state = KVM_MP_STATE_INIT_RECEIVED;
}
- if (test_and_clear_bit(KVM_APIC_SIPI, &apic->pending_events) &&
+ if (test_bit(KVM_APIC_SIPI, &pe) &&
vcpu->arch.mp_state == KVM_MP_STATE_INIT_RECEIVED) {
/* evaluate pending_events before reading the vector */
smp_rmb();
pa_data = boot_params.hdr.setup_data;
while (pa_data) {
- data = phys_to_virt(pa_data);
+ data = ioremap(pa_data, sizeof(*rom));
+ if (!data)
+ return -ENOMEM;
if (data->type == SETUP_PCI) {
rom = (struct pci_setup_rom *)data;
}
}
pa_data = data->next;
+ iounmap(data);
}
return 0;
}
*/
static bool type1_access_ok(unsigned int bus, unsigned int devfn, int reg)
{
- if (bus == 0 && (devfn == PCI_DEVFN(2, 0)
- || devfn == PCI_DEVFN(0, 0)
- || devfn == PCI_DEVFN(3, 0)))
- return 1;
-
/* This is a workaround for A0 LNC bug where PCI status register does
* not have new CAP bit set. can not be written by SW either.
*
*/
if (reg >= 0x100 || reg == PCI_STATUS || reg == PCI_HEADER_TYPE)
return 0;
-
+ if (bus == 0 && (devfn == PCI_DEVFN(2, 0)
+ || devfn == PCI_DEVFN(0, 0)
+ || devfn == PCI_DEVFN(3, 0)))
+ return 1;
return 0; /* langwell on others */
}
}
if (boot_used_size && !finished) {
- unsigned long size;
+ unsigned long size = 0;
u32 attr;
efi_status_t s;
void *tmp;
{
unsigned cpu;
unsigned int this_cpu = smp_processor_id();
+ int xen_vector = xen_map_vector(vector);
- if (!(num_online_cpus() > 1))
+ if (!(num_online_cpus() > 1) || (xen_vector < 0))
return;
for_each_cpu_and(cpu, mask, cpu_online_mask) {
if (this_cpu == cpu)
continue;
- xen_smp_send_call_function_single_ipi(cpu);
+ xen_send_IPI_one(cpu, xen_vector);
}
}
void xen_send_IPI_allbutself(int vector)
{
- int xen_vector = xen_map_vector(vector);
-
- if (xen_vector >= 0)
- xen_send_IPI_mask_allbutself(cpu_online_mask, xen_vector);
+ xen_send_IPI_mask_allbutself(cpu_online_mask, vector);
}
static irqreturn_t xen_call_function_interrupt(int irq, void *dev_id)
extern void xen_send_IPI_mask_allbutself(const struct cpumask *mask,
int vector);
extern void xen_send_IPI_allbutself(int vector);
-extern void physflat_send_IPI_allbutself(int vector);
extern void xen_send_IPI_all(int vector);
extern void xen_send_IPI_self(int vector);
# Power management related files
acpi-y += wakeup.o
acpi-y += sleep.o
-acpi-$(CONFIG_PM) += device_pm.o
+acpi-y += device_pm.o
acpi-$(CONFIG_ACPI_SLEEP) += proc.o
acpi-y += ec.o
acpi-$(CONFIG_ACPI_DOCK) += dock.o
acpi-y += pci_root.o pci_link.o pci_irq.o
-acpi-y += csrt.o
acpi-$(CONFIG_X86_INTEL_LPSS) += acpi_lpss.o
acpi-y += acpi_platform.o
acpi-y += power.o
struct lpss_device_desc {
bool clk_required;
- const char *clk_parent;
+ const char *clkdev_name;
bool ltr_required;
unsigned int prv_offset;
};
+static struct lpss_device_desc lpss_dma_desc = {
+ .clk_required = true,
+ .clkdev_name = "hclk",
+};
+
struct lpss_private_data {
void __iomem *mmio_base;
resource_size_t mmio_size;
static struct lpss_device_desc lpt_dev_desc = {
.clk_required = true,
- .clk_parent = "lpss_clk",
.prv_offset = 0x800,
.ltr_required = true,
};
};
static const struct acpi_device_id acpi_lpss_device_ids[] = {
+ /* Generic LPSS devices */
+ { "INTL9C60", (unsigned long)&lpss_dma_desc },
+
/* Lynxpoint LPSS devices */
{ "INT33C0", (unsigned long)&lpt_dev_desc },
{ "INT33C1", (unsigned long)&lpt_dev_desc },
struct lpss_private_data *pdata)
{
const struct lpss_device_desc *dev_desc = pdata->dev_desc;
+ struct lpss_clk_data *clk_data;
if (!lpss_clk_dev)
lpt_register_clock_device();
- if (!dev_desc->clk_parent || !pdata->mmio_base
+ clk_data = platform_get_drvdata(lpss_clk_dev);
+ if (!clk_data)
+ return -ENODEV;
+
+ if (dev_desc->clkdev_name) {
+ clk_register_clkdev(clk_data->clk, dev_desc->clkdev_name,
+ dev_name(&adev->dev));
+ return 0;
+ }
+
+ if (!pdata->mmio_base
|| pdata->mmio_size < dev_desc->prv_offset + LPSS_CLK_SIZE)
return -ENODATA;
pdata->clk = clk_register_gate(NULL, dev_name(&adev->dev),
- dev_desc->clk_parent, 0,
+ clk_data->name, 0,
pdata->mmio_base + dev_desc->prv_offset,
0, 0, NULL);
if (IS_ERR(pdata->clk))
static void cper_print_pcie(const char *pfx, const struct cper_sec_pcie *pcie,
const struct acpi_hest_generic_data *gdata)
{
-#ifdef CONFIG_ACPI_APEI_PCIEAER
- struct pci_dev *dev;
-#endif
-
if (pcie->validation_bits & CPER_PCIE_VALID_PORT_TYPE)
printk("%s""port_type: %d, %s\n", pfx, pcie->port_type,
pcie->port_type < ARRAY_SIZE(cper_pcie_port_type_strs) ?
printk(
"%s""bridge: secondary_status: 0x%04x, control: 0x%04x\n",
pfx, pcie->bridge.secondary_status, pcie->bridge.control);
-#ifdef CONFIG_ACPI_APEI_PCIEAER
- dev = pci_get_domain_bus_and_slot(pcie->device_id.segment,
- pcie->device_id.bus, pcie->device_id.function);
- if (!dev) {
- pr_err("PCI AER Cannot get PCI device %04x:%02x:%02x.%d\n",
- pcie->device_id.segment, pcie->device_id.bus,
- pcie->device_id.slot, pcie->device_id.function);
- return;
- }
- if (pcie->validation_bits & CPER_PCIE_VALID_AER_INFO)
- cper_print_aer(pfx, dev, gdata->error_severity,
- (struct aer_capability_regs *) pcie->aer_info);
- pci_dev_put(dev);
-#endif
}
static const char *apei_estatus_section_flag_strs[] = {
aer_severity = cper_severity_to_aer(sev);
aer_recover_queue(pcie_err->device_id.segment,
pcie_err->device_id.bus,
- devfn, aer_severity);
+ devfn, aer_severity,
+ (struct aer_capability_regs *)
+ pcie_err->aer_info);
}
}
break;
case ACPI_HEST_NOTIFY_EXTERNAL:
/* External interrupt vector is GSI */
- if (acpi_gsi_to_irq(generic->notify.vector, &ghes->irq)) {
+ rc = acpi_gsi_to_irq(generic->notify.vector, &ghes->irq);
+ if (rc) {
pr_err(GHES_PFX "Failed to map GSI to IRQ for generic hardware error source: %d\n",
generic->header.source_id);
goto err_edac_unreg;
}
- if (request_irq(ghes->irq, ghes_irq_func,
- 0, "GHES IRQ", ghes)) {
+ rc = request_irq(ghes->irq, ghes_irq_func, 0, "GHES IRQ", ghes);
+ if (rc) {
pr_err(GHES_PFX "Failed to register IRQ for generic hardware error source: %d\n",
generic->header.source_id);
goto err_edac_unreg;
+++ /dev/null
-/*
- * Support for Core System Resources Table (CSRT)
- *
- * Copyright (C) 2013, Intel Corporation
- * Authors: Mika Westerberg <mika.westerberg@linux.intel.com>
- * Andy Shevchenko <andriy.shevchenko@linux.intel.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#define pr_fmt(fmt) "ACPI: CSRT: " fmt
-
-#include <linux/acpi.h>
-#include <linux/device.h>
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/sizes.h>
-
-ACPI_MODULE_NAME("CSRT");
-
-static int __init acpi_csrt_parse_shared_info(struct platform_device *pdev,
- const struct acpi_csrt_group *grp)
-{
- const struct acpi_csrt_shared_info *si;
- struct resource res[3];
- size_t nres;
- int ret;
-
- memset(res, 0, sizeof(res));
- nres = 0;
-
- si = (const struct acpi_csrt_shared_info *)&grp[1];
- /*
- * The peripherals that are listed on CSRT typically support only
- * 32-bit addresses so we only use the low part of MMIO base for
- * now.
- */
- if (!si->mmio_base_high && si->mmio_base_low) {
- /*
- * There is no size of the memory resource in shared_info
- * so we assume that it is 4k here.
- */
- res[nres].start = si->mmio_base_low;
- res[nres].end = res[0].start + SZ_4K - 1;
- res[nres++].flags = IORESOURCE_MEM;
- }
-
- if (si->gsi_interrupt) {
- int irq = acpi_register_gsi(NULL, si->gsi_interrupt,
- si->interrupt_mode,
- si->interrupt_polarity);
- res[nres].start = irq;
- res[nres].end = irq;
- res[nres++].flags = IORESOURCE_IRQ;
- }
-
- if (si->base_request_line || si->num_handshake_signals) {
- /*
- * We pass the driver a DMA resource describing the range
- * of request lines the device supports.
- */
- res[nres].start = si->base_request_line;
- res[nres].end = res[nres].start + si->num_handshake_signals - 1;
- res[nres++].flags = IORESOURCE_DMA;
- }
-
- ret = platform_device_add_resources(pdev, res, nres);
- if (ret) {
- if (si->gsi_interrupt)
- acpi_unregister_gsi(si->gsi_interrupt);
- return ret;
- }
-
- return 0;
-}
-
-static int __init
-acpi_csrt_parse_resource_group(const struct acpi_csrt_group *grp)
-{
- struct platform_device *pdev;
- char vendor[5], name[16];
- int ret, i;
-
- vendor[0] = grp->vendor_id;
- vendor[1] = grp->vendor_id >> 8;
- vendor[2] = grp->vendor_id >> 16;
- vendor[3] = grp->vendor_id >> 24;
- vendor[4] = '\0';
-
- if (grp->shared_info_length != sizeof(struct acpi_csrt_shared_info))
- return -ENODEV;
-
- snprintf(name, sizeof(name), "%s%04X", vendor, grp->device_id);
- pdev = platform_device_alloc(name, PLATFORM_DEVID_AUTO);
- if (!pdev)
- return -ENOMEM;
-
- /* Add resources based on the shared info */
- ret = acpi_csrt_parse_shared_info(pdev, grp);
- if (ret)
- goto fail;
-
- ret = platform_device_add(pdev);
- if (ret)
- goto fail;
-
- for (i = 0; i < pdev->num_resources; i++)
- dev_dbg(&pdev->dev, "%pR\n", &pdev->resource[i]);
-
- return 0;
-
-fail:
- platform_device_put(pdev);
- return ret;
-}
-
-/*
- * CSRT or Core System Resources Table is a proprietary ACPI table
- * introduced by Microsoft. This table can contain devices that are not in
- * the system DSDT table. In particular DMA controllers might be described
- * here.
- *
- * We present these devices as normal platform devices that don't have ACPI
- * IDs or handle. The platform device name will be something like
- * <VENDOR><DEVID>.<n>.auto for example: INTL9C06.0.auto.
- */
-void __init acpi_csrt_init(void)
-{
- struct acpi_csrt_group *grp, *end;
- struct acpi_table_csrt *csrt;
- acpi_status status;
- int ret;
-
- status = acpi_get_table(ACPI_SIG_CSRT, 0,
- (struct acpi_table_header **)&csrt);
- if (ACPI_FAILURE(status)) {
- if (status != AE_NOT_FOUND)
- pr_warn("failed to get the CSRT table\n");
- return;
- }
-
- pr_debug("parsing CSRT table for devices\n");
-
- grp = (struct acpi_csrt_group *)(csrt + 1);
- end = (struct acpi_csrt_group *)((void *)csrt + csrt->header.length);
-
- while (grp < end) {
- ret = acpi_csrt_parse_resource_group(grp);
- if (ret) {
- pr_warn("error in parsing resource group: %d\n", ret);
- return;
- }
-
- grp = (struct acpi_csrt_group *)((void *)grp + grp->length);
- }
-}
#define _COMPONENT ACPI_POWER_COMPONENT
ACPI_MODULE_NAME("device_pm");
-static DEFINE_MUTEX(acpi_pm_notifier_lock);
-
-/**
- * acpi_add_pm_notifier - Register PM notifier for given ACPI device.
- * @adev: ACPI device to add the notifier for.
- * @context: Context information to pass to the notifier routine.
- *
- * NOTE: @adev need not be a run-wake or wakeup device to be a valid source of
- * PM wakeup events. For example, wakeup events may be generated for bridges
- * if one of the devices below the bridge is signaling wakeup, even if the
- * bridge itself doesn't have a wakeup GPE associated with it.
- */
-acpi_status acpi_add_pm_notifier(struct acpi_device *adev,
- acpi_notify_handler handler, void *context)
-{
- acpi_status status = AE_ALREADY_EXISTS;
-
- mutex_lock(&acpi_pm_notifier_lock);
-
- if (adev->wakeup.flags.notifier_present)
- goto out;
-
- status = acpi_install_notify_handler(adev->handle,
- ACPI_SYSTEM_NOTIFY,
- handler, context);
- if (ACPI_FAILURE(status))
- goto out;
-
- adev->wakeup.flags.notifier_present = true;
-
- out:
- mutex_unlock(&acpi_pm_notifier_lock);
- return status;
-}
-
-/**
- * acpi_remove_pm_notifier - Unregister PM notifier from given ACPI device.
- * @adev: ACPI device to remove the notifier from.
- */
-acpi_status acpi_remove_pm_notifier(struct acpi_device *adev,
- acpi_notify_handler handler)
-{
- acpi_status status = AE_BAD_PARAMETER;
-
- mutex_lock(&acpi_pm_notifier_lock);
-
- if (!adev->wakeup.flags.notifier_present)
- goto out;
-
- status = acpi_remove_notify_handler(adev->handle,
- ACPI_SYSTEM_NOTIFY,
- handler);
- if (ACPI_FAILURE(status))
- goto out;
-
- adev->wakeup.flags.notifier_present = false;
-
- out:
- mutex_unlock(&acpi_pm_notifier_lock);
- return status;
-}
-
/**
* acpi_power_state_string - String representation of ACPI device power state.
* @state: ACPI device power state to return the string representation of.
if (result)
return result;
} else if (state == ACPI_STATE_UNKNOWN) {
- /* No power resources and missing _PSC? Try to force D0. */
+ /*
+ * No power resources and missing _PSC? Cross fingers and make
+ * it D0 in hope that this is what the BIOS put the device into.
+ * [We tried to force D0 here by executing _PS0, but that broke
+ * Toshiba P870-303 in a nasty way.]
+ */
state = ACPI_STATE_D0;
- result = acpi_dev_pm_explicit_set(device, state);
- if (result)
- return result;
}
device->power.state = state;
return 0;
}
EXPORT_SYMBOL(acpi_bus_power_manageable);
+#ifdef CONFIG_PM
+static DEFINE_MUTEX(acpi_pm_notifier_lock);
+
+/**
+ * acpi_add_pm_notifier - Register PM notifier for given ACPI device.
+ * @adev: ACPI device to add the notifier for.
+ * @context: Context information to pass to the notifier routine.
+ *
+ * NOTE: @adev need not be a run-wake or wakeup device to be a valid source of
+ * PM wakeup events. For example, wakeup events may be generated for bridges
+ * if one of the devices below the bridge is signaling wakeup, even if the
+ * bridge itself doesn't have a wakeup GPE associated with it.
+ */
+acpi_status acpi_add_pm_notifier(struct acpi_device *adev,
+ acpi_notify_handler handler, void *context)
+{
+ acpi_status status = AE_ALREADY_EXISTS;
+
+ mutex_lock(&acpi_pm_notifier_lock);
+
+ if (adev->wakeup.flags.notifier_present)
+ goto out;
+
+ status = acpi_install_notify_handler(adev->handle,
+ ACPI_SYSTEM_NOTIFY,
+ handler, context);
+ if (ACPI_FAILURE(status))
+ goto out;
+
+ adev->wakeup.flags.notifier_present = true;
+
+ out:
+ mutex_unlock(&acpi_pm_notifier_lock);
+ return status;
+}
+
+/**
+ * acpi_remove_pm_notifier - Unregister PM notifier from given ACPI device.
+ * @adev: ACPI device to remove the notifier from.
+ */
+acpi_status acpi_remove_pm_notifier(struct acpi_device *adev,
+ acpi_notify_handler handler)
+{
+ acpi_status status = AE_BAD_PARAMETER;
+
+ mutex_lock(&acpi_pm_notifier_lock);
+
+ if (!adev->wakeup.flags.notifier_present)
+ goto out;
+
+ status = acpi_remove_notify_handler(adev->handle,
+ ACPI_SYSTEM_NOTIFY,
+ handler);
+ if (ACPI_FAILURE(status))
+ goto out;
+
+ adev->wakeup.flags.notifier_present = false;
+
+ out:
+ mutex_unlock(&acpi_pm_notifier_lock);
+ return status;
+}
+
bool acpi_bus_can_wakeup(acpi_handle handle)
{
struct acpi_device *device;
mutex_unlock(&adev->physical_node_lock);
}
EXPORT_SYMBOL_GPL(acpi_dev_pm_remove_dependent);
+#endif /* CONFIG_PM */
void acpi_pci_root_hp_init(void);
void acpi_platform_init(void);
int acpi_sysfs_init(void);
-void acpi_csrt_init(void);
#ifdef CONFIG_ACPI_CONTAINER
void acpi_container_init(void);
#else
/* bus enumerate */
printk(KERN_DEBUG "%s: Bus check notify on %s\n", __func__,
(char *)buffer.pointer);
- if (!root)
+ if (root)
+ acpiphp_check_host_bridge(handle);
+ else
handle_root_bridge_insertion(handle);
break;
acpi_pci_link_init();
acpi_platform_init();
acpi_lpss_init();
- acpi_csrt_init();
acpi_container_init();
acpi_memory_hotplug_init();
DMI_MATCH(DMI_PRODUCT_NAME, "HP Pavilion dm4 Notebook PC"),
},
},
+ {
+ .callback = video_ignore_initial_backlight,
+ .ident = "HP Pavilion g6 Notebook PC",
+ .matches = {
+ DMI_MATCH(DMI_BOARD_VENDOR, "Hewlett-Packard"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "HP Pavilion g6 Notebook PC"),
+ },
+ },
{
.callback = video_ignore_initial_backlight,
.ident = "HP 1000 Notebook PC",
DMI_MATCH(DMI_PRODUCT_NAME, "HP 1000 Notebook PC"),
},
},
+ {
+ .callback = video_ignore_initial_backlight,
+ .ident = "HP Pavilion m4",
+ .matches = {
+ DMI_MATCH(DMI_BOARD_VENDOR, "Hewlett-Packard"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "HP Pavilion m4 Notebook PC"),
+ },
+ },
{}
};
DMI_MATCH(DMI_PRODUCT_NAME, "UL30VT"),
},
},
+ {
+ .callback = video_detect_force_vendor,
+ .ident = "Asus UL30A",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK Computer Inc."),
+ DMI_MATCH(DMI_PRODUCT_NAME, "UL30A"),
+ },
+ },
{ },
};
/*
* acard-ahci.c - ACard AHCI SATA support
*
- * Maintained by: Jeff Garzik <jgarzik@pobox.com>
+ * Maintained by: Tejun Heo <tj@kernel.org>
* Please ALWAYS copy linux-ide@vger.kernel.org
* on emails.
*
/*
* ahci.c - AHCI SATA support
*
- * Maintained by: Jeff Garzik <jgarzik@pobox.com>
+ * Maintained by: Tejun Heo <tj@kernel.org>
* Please ALWAYS copy linux-ide@vger.kernel.org
* on emails.
*
.driver_data = board_ahci_yes_fbs }, /* 88se9125 */
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL_EXT, 0x917a),
.driver_data = board_ahci_yes_fbs }, /* 88se9172 */
+ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL_EXT, 0x9172),
+ .driver_data = board_ahci_yes_fbs }, /* 88se9172 */
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL_EXT, 0x9192),
.driver_data = board_ahci_yes_fbs }, /* 88se9172 on some Gigabyte */
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL_EXT, 0x91a3),
/*
* ahci.h - Common AHCI SATA definitions and declarations
*
- * Maintained by: Jeff Garzik <jgarzik@pobox.com>
+ * Maintained by: Tejun Heo <tj@kernel.org>
* Please ALWAYS copy linux-ide@vger.kernel.org
* on emails.
*
/*
* ata_piix.c - Intel PATA/SATA controllers
*
- * Maintained by: Jeff Garzik <jgarzik@pobox.com>
+ * Maintained by: Tejun Heo <tj@kernel.org>
* Please ALWAYS copy linux-ide@vger.kernel.org
* on emails.
*
piix_pata_vmw, /* PIIX4 for VMware, spurious DMA_ERR */
ich8_sata_snb,
ich8_2port_sata_snb,
+ ich8_2port_sata_byt,
};
struct piix_map_db {
{ 0x8086, 0x8d60, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_snb },
/* SATA Controller IDE (Wellsburg) */
{ 0x8086, 0x8d68, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata },
+ /* SATA Controller IDE (BayTrail) */
+ { 0x8086, 0x0F20, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata_byt },
+ { 0x8086, 0x0F21, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata_byt },
{ } /* terminate list */
};
[tolapai_sata] = &tolapai_map_db,
[ich8_sata_snb] = &ich8_map_db,
[ich8_2port_sata_snb] = &ich8_2port_map_db,
+ [ich8_2port_sata_byt] = &ich8_2port_map_db,
};
static struct pci_bits piix_enable_bits[] = {
.udma_mask = ATA_UDMA6,
.port_ops = &piix_sata_ops,
},
+
+ [ich8_2port_sata_byt] =
+ {
+ .flags = PIIX_SATA_FLAGS | PIIX_FLAG_SIDPR | PIIX_FLAG_PIO16,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
+ .udma_mask = ATA_UDMA6,
+ .port_ops = &piix_sata_ops,
+ },
+
};
#define AHCI_PCI_BAR 5
/*
* libahci.c - Common AHCI SATA low-level routines
*
- * Maintained by: Jeff Garzik <jgarzik@pobox.com>
+ * Maintained by: Tejun Heo <tj@kernel.org>
* Please ALWAYS copy linux-ide@vger.kernel.org
* on emails.
*
/*
* libata-core.c - helper library for ATA
*
- * Maintained by: Jeff Garzik <jgarzik@pobox.com>
+ * Maintained by: Tejun Heo <tj@kernel.org>
* Please ALWAYS copy linux-ide@vger.kernel.org
* on emails.
*
qc->tf = *tf;
if (cdb)
memcpy(qc->cdb, cdb, ATAPI_CDB_LEN);
+
+ /* some SATA bridges need us to indicate data xfer direction */
+ if (tf->protocol == ATAPI_PROT_DMA && (dev->flags & ATA_DFLAG_DMADIR) &&
+ dma_dir == DMA_FROM_DEVICE)
+ qc->tf.feature |= ATAPI_DMADIR;
+
qc->flags |= ATA_QCFLAG_RESULT_TF;
qc->dma_dir = dma_dir;
if (dma_dir != DMA_NONE) {
/*
* libata-eh.c - libata error handling
*
- * Maintained by: Jeff Garzik <jgarzik@pobox.com>
+ * Maintained by: Tejun Heo <tj@kernel.org>
* Please ALWAYS copy linux-ide@vger.kernel.org
* on emails.
*
/*
* libata-scsi.c - helper library for ATA
*
- * Maintained by: Jeff Garzik <jgarzik@pobox.com>
+ * Maintained by: Tejun Heo <tj@kernel.org>
* Please ALWAYS copy linux-ide@vger.kernel.org
* on emails.
*
/*
* libata-sff.c - helper library for PCI IDE BMDMA
*
- * Maintained by: Jeff Garzik <jgarzik@pobox.com>
+ * Maintained by: Tejun Heo <tj@kernel.org>
* Please ALWAYS copy linux-ide@vger.kernel.org
* on emails.
*
/*
* pdc_adma.c - Pacific Digital Corporation ADMA
*
- * Maintained by: Mark Lord <mlord@pobox.com>
+ * Maintained by: Tejun Heo <tj@kernel.org>
*
* Copyright 2005 Mark Lord
*
/*
* sata_promise.c - Promise SATA
*
- * Maintained by: Jeff Garzik <jgarzik@pobox.com>
+ * Maintained by: Tejun Heo <tj@kernel.org>
* Mikael Pettersson <mikpe@it.uu.se>
* Please ALWAYS copy linux-ide@vger.kernel.org
* on emails.
/* start host DMA transaction */
dmactl = ioread32(priv->base + ATAPI_CONTROL1_REG);
+ dmactl &= ~ATAPI_CONTROL1_STOP;
dmactl |= ATAPI_CONTROL1_START;
iowrite32(dmactl, priv->base + ATAPI_CONTROL1_REG);
}
.bmdma_status = sata_rcar_bmdma_status,
};
-static int sata_rcar_serr_interrupt(struct ata_port *ap)
+static void sata_rcar_serr_interrupt(struct ata_port *ap)
{
struct sata_rcar_priv *priv = ap->host->private_data;
struct ata_eh_info *ehi = &ap->link.eh_info;
int freeze = 0;
- int handled = 0;
u32 serror;
serror = ioread32(priv->base + SCRSERR_REG);
if (!serror)
- return 0;
+ return;
DPRINTK("SError @host_intr: 0x%x\n", serror);
ata_ehi_push_desc(ehi, "%s", "hotplug");
freeze = serror & SERR_COMM_WAKE ? 0 : 1;
- handled = 1;
}
/* freeze or abort */
ata_port_freeze(ap);
else
ata_port_abort(ap);
-
- return handled;
}
-static int sata_rcar_ata_interrupt(struct ata_port *ap)
+static void sata_rcar_ata_interrupt(struct ata_port *ap)
{
struct ata_queued_cmd *qc;
int handled = 0;
if (qc)
handled |= ata_bmdma_port_intr(ap, qc);
- return handled;
+ /* be sure to clear ATA interrupt */
+ if (!handled)
+ sata_rcar_check_status(ap);
}
static irqreturn_t sata_rcar_interrupt(int irq, void *dev_instance)
spin_lock_irqsave(&host->lock, flags);
sataintstat = ioread32(priv->base + SATAINTSTAT_REG);
+ sataintstat &= SATA_RCAR_INT_MASK;
if (!sataintstat)
goto done;
/* ack */
- iowrite32(sataintstat & ~SATA_RCAR_INT_MASK,
- priv->base + SATAINTSTAT_REG);
+ iowrite32(~sataintstat & 0x7ff, priv->base + SATAINTSTAT_REG);
ap = host->ports[0];
if (sataintstat & SATAINTSTAT_ATA)
- handled |= sata_rcar_ata_interrupt(ap);
+ sata_rcar_ata_interrupt(ap);
if (sataintstat & SATAINTSTAT_SERR)
- handled |= sata_rcar_serr_interrupt(ap);
+ sata_rcar_serr_interrupt(ap);
+ handled = 1;
done:
spin_unlock_irqrestore(&host->lock, flags);
/*
* sata_sil.c - Silicon Image SATA
*
- * Maintained by: Jeff Garzik <jgarzik@pobox.com>
+ * Maintained by: Tejun Heo <tj@kernel.org>
* Please ALWAYS copy linux-ide@vger.kernel.org
* on emails.
*
/*
* sata_sx4.c - Promise SATA
*
- * Maintained by: Jeff Garzik <jgarzik@pobox.com>
+ * Maintained by: Tejun Heo <tj@kernel.org>
* Please ALWAYS copy linux-ide@vger.kernel.org
* on emails.
*
/*
* sata_via.c - VIA Serial ATA controllers
*
- * Maintained by: Jeff Garzik <jgarzik@pobox.com>
+ * Maintained by: Tejun Heo <tj@kernel.org>
* Please ALWAYS copy linux-ide@vger.kernel.org
* on emails.
*
return subsys_register(subsys, groups, virtual_dir);
}
+EXPORT_SYMBOL_GPL(subsys_virtual_register);
int __init buses_init(void)
{
if (dev) {
WARN(((attr->attr.mode & S_IWUGO) && !attr->store),
- "Write permission without 'store'\n");
+ "Attribute %s: write permission without 'store'\n",
+ attr->attr.name);
WARN(((attr->attr.mode & S_IRUGO) && !attr->show),
- "Read permission without 'show'\n");
+ "Attribute %s: read permission without 'show'\n",
+ attr->attr.name);
error = sysfs_create_file(&dev->kobj, &attr->attr);
}
{ BCMA_CORE_I2S, "I2S" },
{ BCMA_CORE_SDR_DDR1_MEM_CTL, "SDR/DDR1 Memory Controller" },
{ BCMA_CORE_SHIM, "SHIM" },
+ { BCMA_CORE_PCIE2, "PCIe Gen2" },
+ { BCMA_CORE_ARM_CR4, "ARM CR4" },
{ BCMA_CORE_DEFAULT, "Default" },
};
spin_lock(&brd->brd_lock);
idx = sector >> PAGE_SECTORS_SHIFT;
+ page->index = idx;
if (radix_tree_insert(&brd->brd_pages, idx, page)) {
__free_page(page);
page = radix_tree_lookup(&brd->brd_pages, idx);
BUG_ON(!page);
BUG_ON(page->index != idx);
- } else
- page->index = idx;
+ }
spin_unlock(&brd->brd_lock);
radix_tree_preload_end();
dev_dbg(&dev->dev, "ace_probe(%p)\n", dev);
/* device id and bus width */
- of_property_read_u32(dev->dev.of_node, "port-number", &id);
- if (id < 0)
+ if (of_property_read_u32(dev->dev.of_node, "port-number", &id))
id = 0;
if (of_find_property(dev->dev.of_node, "8-bit", NULL))
bus_width = ACE_BUS_WIDTH_8;
return -EFAULT;
break;
case LPGETSTATUS:
+ if (mutex_lock_interruptible(&lp_table[minor].port_mutex))
+ return -EINTR;
lp_claim_parport_or_block (&lp_table[minor]);
status = r_str(minor);
lp_release_parport (&lp_table[minor]);
+ mutex_unlock(&lp_table[minor].port_mutex);
if (copy_to_user(argp, &status, sizeof(int)))
return -EFAULT;
if (r->entropy_count / 8 < min + reserved) {
nbytes = 0;
} else {
+ int entropy_count, orig;
+retry:
+ entropy_count = orig = ACCESS_ONCE(r->entropy_count);
/* If limited, never pull more than available */
- if (r->limit && nbytes + reserved >= r->entropy_count / 8)
- nbytes = r->entropy_count/8 - reserved;
-
- if (r->entropy_count / 8 >= nbytes + reserved)
- r->entropy_count -= nbytes*8;
- else
- r->entropy_count = reserved;
+ if (r->limit && nbytes + reserved >= entropy_count / 8)
+ nbytes = entropy_count/8 - reserved;
+
+ if (entropy_count / 8 >= nbytes + reserved) {
+ entropy_count -= nbytes*8;
+ if (cmpxchg(&r->entropy_count, orig, entropy_count) != orig)
+ goto retry;
+ } else {
+ entropy_count = reserved;
+ if (cmpxchg(&r->entropy_count, orig, entropy_count) != orig)
+ goto retry;
+ }
- if (r->entropy_count < random_write_wakeup_thresh)
+ if (entropy_count < random_write_wakeup_thresh)
wakeup_write = 1;
}
{
ssize_t ret = 0, i;
__u8 tmp[EXTRACT_SIZE];
+ unsigned long flags;
/* if last_data isn't primed, we need EXTRACT_SIZE extra bytes */
- if (fips_enabled && !r->last_data_init)
- nbytes += EXTRACT_SIZE;
+ if (fips_enabled) {
+ spin_lock_irqsave(&r->lock, flags);
+ if (!r->last_data_init) {
+ r->last_data_init = true;
+ spin_unlock_irqrestore(&r->lock, flags);
+ trace_extract_entropy(r->name, EXTRACT_SIZE,
+ r->entropy_count, _RET_IP_);
+ xfer_secondary_pool(r, EXTRACT_SIZE);
+ extract_buf(r, tmp);
+ spin_lock_irqsave(&r->lock, flags);
+ memcpy(r->last_data, tmp, EXTRACT_SIZE);
+ }
+ spin_unlock_irqrestore(&r->lock, flags);
+ }
trace_extract_entropy(r->name, nbytes, r->entropy_count, _RET_IP_);
xfer_secondary_pool(r, nbytes);
extract_buf(r, tmp);
if (fips_enabled) {
- unsigned long flags;
-
-
- /* prime last_data value if need be, per fips 140-2 */
- if (!r->last_data_init) {
- spin_lock_irqsave(&r->lock, flags);
- memcpy(r->last_data, tmp, EXTRACT_SIZE);
- r->last_data_init = true;
- nbytes -= EXTRACT_SIZE;
- spin_unlock_irqrestore(&r->lock, flags);
- extract_buf(r, tmp);
- }
-
spin_lock_irqsave(&r->lock, flags);
if (!memcmp(tmp, r->last_data, EXTRACT_SIZE))
panic("Hardware RNG duplicated output!\n");
{
int ret = -ENOMEM;
- tpk_port.port.ops = &null_ops;
mutex_init(&tpk_port.port_write_mutex);
ttyprintk_driver = tty_alloc_driver(1,
return PTR_ERR(ttyprintk_driver);
tty_port_init(&tpk_port.port);
+ tpk_port.port.ops = &null_ops;
ttyprintk_driver->driver_name = "ttyprintk";
ttyprintk_driver->name = "ttyprintk";
unsigned char reg;
unsigned char rdiv;
- if (hwdata->num > 5)
+ if (hwdata->num <= 5)
reg = si5351_msynth_params_address(hwdata->num) + 2;
else
reg = SI5351_CLK6_7_OUTPUT_DIVIDER;
return -EINVAL;
}
drvdata->onecell.clks[n] = clk;
+
+ /* set initial clkout rate */
+ if (pdata->clkout[n].rate != 0) {
+ int ret;
+ ret = clk_set_rate(clk, pdata->clkout[n].rate);
+ if (ret != 0) {
+ dev_err(&client->dev, "Cannot set rate : %d\n",
+ ret);
+ }
+ }
}
ret = of_clk_add_provider(client->dev.of_node, of_clk_src_onecell_get,
writel(divisor, cdev->div_reg);
vt8500_pmc_wait_busy();
- spin_lock_irqsave(cdev->lock, flags);
+ spin_unlock_irqrestore(cdev->lock, flags);
return 0;
}
*/
#include <linux/clk.h>
+#include <linux/clk/mxs.h>
#include <linux/clkdev.h>
#include <linux/err.h>
#include <linux/init.h>
GATE(smmu_pcie, "smmu_pcie", "aclk133", GATE_IP_FSYS, 18, 0, 0),
GATE(modemif, "modemif", "aclk100", GATE_IP_PERIL, 28, 0, 0),
GATE(chipid, "chipid", "aclk100", E4210_GATE_IP_PERIR, 0, 0, 0),
- GATE(sysreg, "sysreg", "aclk100", E4210_GATE_IP_PERIR, 0, 0, 0),
+ GATE(sysreg, "sysreg", "aclk100", E4210_GATE_IP_PERIR, 0,
+ CLK_IGNORE_UNUSED, 0),
GATE(hdmi_cec, "hdmi_cec", "aclk100", E4210_GATE_IP_PERIR, 11, 0, 0),
GATE(smmu_rotator, "smmu_rotator", "aclk200",
E4210_GATE_IP_IMAGE, 4, 0, 0),
GATE(smmu_mdma, "smmu_mdma", "aclk200", E4X12_GATE_IP_IMAGE, 5, 0, 0),
GATE(mipi_hsi, "mipi_hsi", "aclk133", GATE_IP_FSYS, 10, 0, 0),
GATE(chipid, "chipid", "aclk100", E4X12_GATE_IP_PERIR, 0, 0, 0),
- GATE(sysreg, "sysreg", "aclk100", E4X12_GATE_IP_PERIR, 1, 0, 0),
+ GATE(sysreg, "sysreg", "aclk100", E4X12_GATE_IP_PERIR, 1,
+ CLK_IGNORE_UNUSED, 0),
GATE(hdmi_cec, "hdmi_cec", "aclk100", E4X12_GATE_IP_PERIR, 11, 0, 0),
GATE(sclk_mdnie0, "sclk_mdnie0", "div_mdnie0",
SRC_MASK_LCD0, 4, CLK_SET_RATE_PARENT, 0),
struct clk *clk;
int i;
+ /* ac97 */
+ clk = tegra_clk_register_periph_gate("ac97", "pll_a_out0",
+ TEGRA_PERIPH_ON_APB,
+ clk_base, 0, 3, &periph_l_regs,
+ periph_clk_enb_refcnt);
+ clk_register_clkdev(clk, NULL, "tegra20-ac97");
+ clks[ac97] = clk;
+
/* apbdma */
clk = tegra_clk_register_periph_gate("apbdma", "pclk", 0, clk_base,
0, 34, &periph_h_regs,
{uartc, pll_p, 0, 0},
{uartd, pll_p, 0, 0},
{uarte, pll_p, 0, 0},
- {usbd, clk_max, 12000000, 0},
- {usb2, clk_max, 12000000, 0},
- {usb3, clk_max, 12000000, 0},
{pll_a, clk_max, 56448000, 1},
{pll_a_out0, clk_max, 11289600, 1},
{cdev1, clk_max, 0, 1},
return ERR_PTR(-ENOMEM);
}
- for (i = 0; i < num_parents; i++) {
+ /* set main clock registers */
+ clk->reg_sel[0] = reg_sel[0];
+ clk->reg_bits[0] = reg_bits[0];
+ clk->reg_mask[0] = reg_mask[0];
+
+ /* handle clocks with more than one parent */
+ for (i = 1; i < num_parents; i++) {
clk->reg_sel[i] = reg_sel[i];
clk->reg_bits[i] = reg_bits[i];
clk->reg_mask[i] = reg_mask[i];
clk = clk_reg_prcc_pclk("p3_pclk0", "per3clk", clkrst3_base,
BIT(0), 0);
clk_register_clkdev(clk, "fsmc", NULL);
- clk_register_clkdev(clk, NULL, "smsc911x");
+ clk_register_clkdev(clk, NULL, "smsc911x.0");
clk = clk_reg_prcc_pclk("p3_pclk1", "per3clk", clkrst3_base,
BIT(1), 0);
#include <linux/clk-provider.h>
#include <linux/err.h>
#include <linux/module.h>
+#include <linux/platform_data/clk-lpss.h>
#include <linux/platform_device.h>
#define PRV_CLOCK_PARAMS 0x800
static int lpt_clk_probe(struct platform_device *pdev)
{
+ struct lpss_clk_data *drvdata;
struct clk *clk;
+ drvdata = devm_kzalloc(&pdev->dev, sizeof(*drvdata), GFP_KERNEL);
+ if (!drvdata)
+ return -ENOMEM;
+
/* LPSS free running clock */
- clk = clk_register_fixed_rate(&pdev->dev, "lpss_clk", NULL, CLK_IS_ROOT,
- 100000000);
+ drvdata->name = "lpss_clk";
+ clk = clk_register_fixed_rate(&pdev->dev, drvdata->name, NULL,
+ CLK_IS_ROOT, 100000000);
if (IS_ERR(clk))
return PTR_ERR(clk);
- /* Shared DMA clock */
- clk_register_clkdev(clk, "hclk", "INTL9C60.0.auto");
+ drvdata->clk = clk;
+ platform_set_drvdata(pdev, drvdata);
return 0;
}
config X86_E_POWERSAVER
tristate "VIA C7 Enhanced PowerSaver (DANGEROUS)"
select CPU_FREQ_TABLE
- depends on X86_32
+ depends on X86_32 && ACPI_PROCESSOR
help
This adds the CPUFreq driver for VIA C7 processors. However, this driver
does not have any safeguards to prevent operating the CPU out of spec
switch (per_cpu(acfreq_data, cpumask_first(mask))->cpu_feature) {
case SYSTEM_INTEL_MSR_CAPABLE:
cmd.type = SYSTEM_INTEL_MSR_CAPABLE;
- cmd.addr.msr.reg = MSR_IA32_PERF_STATUS;
+ cmd.addr.msr.reg = MSR_IA32_PERF_CTL;
break;
case SYSTEM_AMD_MSR_CAPABLE:
cmd.type = SYSTEM_AMD_MSR_CAPABLE;
- cmd.addr.msr.reg = MSR_AMD_PERF_STATUS;
+ cmd.addr.msr.reg = MSR_AMD_PERF_CTL;
break;
case SYSTEM_IO_CAPABLE:
cmd.type = SYSTEM_IO_CAPABLE;
#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+#include <linux/cpu.h>
#include <linux/cpufreq.h>
#include <linux/device.h>
#include <linux/export.h>
#include <linux/module.h>
#include <linux/of.h>
#include <linux/opp.h>
+#include <linux/platform_device.h>
#include <linux/slab.h>
#include <linux/types.h>
#include "arm_big_little.h"
-static int dt_init_opp_table(struct device *cpu_dev)
+/* get cpu node with valid operating-points */
+static struct device_node *get_cpu_node_with_valid_op(int cpu)
{
- struct device_node *np, *parent;
- int count = 0, ret;
+ struct device_node *np = NULL, *parent;
+ int count = 0;
parent = of_find_node_by_path("/cpus");
if (!parent) {
pr_err("failed to find OF /cpus\n");
- return -ENOENT;
+ return NULL;
}
for_each_child_of_node(parent, np) {
- if (count++ != cpu_dev->id)
+ if (count++ != cpu)
continue;
if (!of_get_property(np, "operating-points", NULL)) {
- ret = -ENODATA;
- } else {
- cpu_dev->of_node = np;
- ret = of_init_opp_table(cpu_dev);
+ of_node_put(np);
+ np = NULL;
}
- of_node_put(np);
- of_node_put(parent);
- return ret;
+ break;
}
- return -ENODEV;
+ of_node_put(parent);
+ return np;
+}
+
+static int dt_init_opp_table(struct device *cpu_dev)
+{
+ struct device_node *np;
+ int ret;
+
+ np = get_cpu_node_with_valid_op(cpu_dev->id);
+ if (!np)
+ return -ENODATA;
+
+ cpu_dev->of_node = np;
+ ret = of_init_opp_table(cpu_dev);
+ of_node_put(np);
+
+ return ret;
}
static int dt_get_transition_latency(struct device *cpu_dev)
{
- struct device_node *np, *parent;
+ struct device_node *np;
u32 transition_latency = CPUFREQ_ETERNAL;
- int count = 0;
- parent = of_find_node_by_path("/cpus");
- if (!parent) {
- pr_info("Failed to find OF /cpus. Use CPUFREQ_ETERNAL transition latency\n");
+ np = get_cpu_node_with_valid_op(cpu_dev->id);
+ if (!np)
return CPUFREQ_ETERNAL;
- }
-
- for_each_child_of_node(parent, np) {
- if (count++ != cpu_dev->id)
- continue;
- of_property_read_u32(np, "clock-latency", &transition_latency);
- of_node_put(np);
- of_node_put(parent);
+ of_property_read_u32(np, "clock-latency", &transition_latency);
+ of_node_put(np);
- return transition_latency;
- }
-
- pr_info("clock-latency isn't found, use CPUFREQ_ETERNAL transition latency\n");
- return CPUFREQ_ETERNAL;
+ pr_debug("%s: clock-latency: %d\n", __func__, transition_latency);
+ return transition_latency;
}
static struct cpufreq_arm_bL_ops dt_bL_ops = {
.init_opp_table = dt_init_opp_table,
};
-static int generic_bL_init(void)
+static int generic_bL_probe(struct platform_device *pdev)
{
+ struct device_node *np;
+
+ np = get_cpu_node_with_valid_op(0);
+ if (!np)
+ return -ENODEV;
+
+ of_node_put(np);
return bL_cpufreq_register(&dt_bL_ops);
}
-module_init(generic_bL_init);
-static void generic_bL_exit(void)
+static int generic_bL_remove(struct platform_device *pdev)
{
- return bL_cpufreq_unregister(&dt_bL_ops);
+ bL_cpufreq_unregister(&dt_bL_ops);
+ return 0;
}
-module_exit(generic_bL_exit);
+
+static struct platform_driver generic_bL_platdrv = {
+ .driver = {
+ .name = "arm-bL-cpufreq-dt",
+ .owner = THIS_MODULE,
+ },
+ .probe = generic_bL_probe,
+ .remove = generic_bL_remove,
+};
+module_platform_driver(generic_bL_platdrv);
MODULE_AUTHOR("Viresh Kumar <viresh.kumar@linaro.org>");
MODULE_DESCRIPTION("Generic ARM big LITTLE cpufreq driver via DT");
struct cpufreq_freqs freqs;
struct opp *opp;
unsigned long volt = 0, volt_old = 0, tol = 0;
- long freq_Hz;
+ long freq_Hz, freq_exact;
unsigned int index;
int ret;
freq_Hz = clk_round_rate(cpu_clk, freq_table[index].frequency * 1000);
if (freq_Hz < 0)
freq_Hz = freq_table[index].frequency * 1000;
+ freq_exact = freq_Hz;
freqs.new = freq_Hz / 1000;
freqs.old = clk_get_rate(cpu_clk) / 1000;
}
}
- ret = clk_set_rate(cpu_clk, freqs.new * 1000);
+ ret = clk_set_rate(cpu_clk, freq_exact);
if (ret) {
pr_err("failed to set clock rate: %d\n", ret);
if (cpu_reg)
/* end old governor */
if (data->governor) {
__cpufreq_governor(data, CPUFREQ_GOV_STOP);
+ unlock_policy_rwsem_write(policy->cpu);
__cpufreq_governor(data,
CPUFREQ_GOV_POLICY_EXIT);
+ lock_policy_rwsem_write(policy->cpu);
}
/* start new governor */
data->governor = policy->governor;
if (!__cpufreq_governor(data, CPUFREQ_GOV_POLICY_INIT)) {
- if (!__cpufreq_governor(data, CPUFREQ_GOV_START))
+ if (!__cpufreq_governor(data, CPUFREQ_GOV_START)) {
failed = 0;
- else
+ } else {
+ unlock_policy_rwsem_write(policy->cpu);
__cpufreq_governor(data,
CPUFREQ_GOV_POLICY_EXIT);
+ lock_policy_rwsem_write(policy->cpu);
+ }
}
if (failed) {
#include <linux/tick.h>
#include <linux/types.h>
#include <linux/workqueue.h>
+#include <linux/cpu.h>
#include "cpufreq_governor.h"
if (!all_cpus) {
__gov_queue_work(smp_processor_id(), dbs_data, delay);
} else {
+ get_online_cpus();
for_each_cpu(i, policy->cpus)
__gov_queue_work(i, dbs_data, delay);
+ put_online_cpus();
}
}
EXPORT_SYMBOL_GPL(gov_queue_work);
static const struct x86_cpu_id intel_pstate_cpu_ids[] = {
ICPU(0x2a, default_policy),
ICPU(0x2d, default_policy),
+ ICPU(0x3a, default_policy),
{}
};
MODULE_DEVICE_TABLE(x86cpu, intel_pstate_cpu_ids);
dst_nents = sg_count(req->dst, req->cryptlen, &dst_chained);
sgc = dma_map_sg_chained(jrdev, req->assoc, assoc_nents ? : 1,
- DMA_BIDIRECTIONAL, assoc_chained);
+ DMA_TO_DEVICE, assoc_chained);
if (likely(req->src == req->dst)) {
sgc = dma_map_sg_chained(jrdev, req->src, src_nents ? : 1,
DMA_BIDIRECTIONAL, src_chained);
dst_nents = sg_count(req->dst, req->cryptlen, &dst_chained);
sgc = dma_map_sg_chained(jrdev, req->assoc, assoc_nents ? : 1,
- DMA_BIDIRECTIONAL, assoc_chained);
+ DMA_TO_DEVICE, assoc_chained);
if (likely(req->src == req->dst)) {
sgc = dma_map_sg_chained(jrdev, req->src, src_nents ? : 1,
DMA_BIDIRECTIONAL, src_chained);
.cra_blocksize = AES_BLOCK_SIZE,
.cra_ctxsize = sizeof(struct nx_crypto_ctx),
.cra_type = &crypto_blkcipher_type,
+ .cra_alignmask = 0xf,
.cra_module = THIS_MODULE,
.cra_init = nx_crypto_ctx_aes_cbc_init,
.cra_exit = nx_crypto_ctx_exit,
.cra_priority = 300,
.cra_flags = CRYPTO_ALG_TYPE_BLKCIPHER,
.cra_blocksize = AES_BLOCK_SIZE,
+ .cra_alignmask = 0xf,
.cra_ctxsize = sizeof(struct nx_crypto_ctx),
.cra_type = &crypto_blkcipher_type,
.cra_module = THIS_MODULE,
if (enc)
NX_CPB_FDM(csbcpb) |= NX_FDM_ENDE_ENCRYPT;
else
- nbytes -= AES_BLOCK_SIZE;
+ nbytes -= crypto_aead_authsize(crypto_aead_reqtfm(req));
csbcpb->cpb.aes_gcm.bit_length_data = nbytes * 8;
* 1: <= SHA256_BLOCK_SIZE: copy into state, return 0
* 2: > SHA256_BLOCK_SIZE: process X blocks, copy in leftover
*/
- if (len + sctx->count <= SHA256_BLOCK_SIZE) {
+ if (len + sctx->count < SHA256_BLOCK_SIZE) {
memcpy(sctx->buf + sctx->count, data, len);
sctx->count += len;
goto out;
atomic_inc(&(nx_ctx->stats->sha256_ops));
/* copy the leftover back into the state struct */
- memcpy(sctx->buf, data + len - leftover, leftover);
+ if (leftover)
+ memcpy(sctx->buf, data + len - leftover, leftover);
sctx->count = leftover;
csbcpb->cpb.sha256.message_bit_length += (u64)
struct nx_sg *in_sg, *out_sg;
int rc;
+
if (NX_CPB_FDM(csbcpb) & NX_FDM_CONTINUATION) {
/* we've hit the nx chip previously, now we're finalizing,
* so copy over the partial digest */
atomic_inc(&(nx_ctx->stats->sha256_ops));
- atomic64_add(csbcpb->cpb.sha256.message_bit_length,
+ atomic64_add(csbcpb->cpb.sha256.message_bit_length / 8,
&(nx_ctx->stats->sha256_bytes));
memcpy(out, csbcpb->cpb.sha256.message_digest, SHA256_DIGEST_SIZE);
out:
* 1: <= SHA512_BLOCK_SIZE: copy into state, return 0
* 2: > SHA512_BLOCK_SIZE: process X blocks, copy in leftover
*/
- if ((u64)len + sctx->count[0] <= SHA512_BLOCK_SIZE) {
+ if ((u64)len + sctx->count[0] < SHA512_BLOCK_SIZE) {
memcpy(sctx->buf + sctx->count[0], data, len);
sctx->count[0] += len;
goto out;
atomic_inc(&(nx_ctx->stats->sha512_ops));
/* copy the leftover back into the state struct */
- memcpy(sctx->buf, data + len - leftover, leftover);
+ if (leftover)
+ memcpy(sctx->buf, data + len - leftover, leftover);
sctx->count[0] = leftover;
spbc_bits = csbcpb->cpb.sha512.spbc * 8;
goto out;
atomic_inc(&(nx_ctx->stats->sha512_ops));
- atomic64_add(csbcpb->cpb.sha512.message_bit_length_lo,
+ atomic64_add(csbcpb->cpb.sha512.message_bit_length_lo / 8,
&(nx_ctx->stats->sha512_bytes));
memcpy(out, csbcpb->cpb.sha512.message_digest, SHA512_DIGEST_SIZE);
{
struct nx_sg *nx_insg = nx_ctx->in_sg;
struct nx_sg *nx_outsg = nx_ctx->out_sg;
- struct blkcipher_walk walk;
- int rc;
-
- blkcipher_walk_init(&walk, dst, src, nbytes);
- rc = blkcipher_walk_virt_block(desc, &walk, AES_BLOCK_SIZE);
- if (rc)
- goto out;
if (iv)
- memcpy(iv, walk.iv, AES_BLOCK_SIZE);
+ memcpy(iv, desc->info, AES_BLOCK_SIZE);
- while (walk.nbytes) {
- nx_insg = nx_build_sg_list(nx_insg, walk.src.virt.addr,
- walk.nbytes, nx_ctx->ap->sglen);
- nx_outsg = nx_build_sg_list(nx_outsg, walk.dst.virt.addr,
- walk.nbytes, nx_ctx->ap->sglen);
-
- rc = blkcipher_walk_done(desc, &walk, 0);
- if (rc)
- break;
- }
-
- if (walk.nbytes) {
- nx_insg = nx_build_sg_list(nx_insg, walk.src.virt.addr,
- walk.nbytes, nx_ctx->ap->sglen);
- nx_outsg = nx_build_sg_list(nx_outsg, walk.dst.virt.addr,
- walk.nbytes, nx_ctx->ap->sglen);
-
- rc = 0;
- }
+ nx_insg = nx_walk_and_build(nx_insg, nx_ctx->ap->sglen, src, 0, nbytes);
+ nx_outsg = nx_walk_and_build(nx_outsg, nx_ctx->ap->sglen, dst, 0, nbytes);
/* these lengths should be negative, which will indicate to phyp that
* the input and output parameters are scatterlists, not linear
* buffers */
nx_ctx->op.inlen = (nx_ctx->in_sg - nx_insg) * sizeof(struct nx_sg);
nx_ctx->op.outlen = (nx_ctx->out_sg - nx_outsg) * sizeof(struct nx_sg);
-out:
- return rc;
+
+ return 0;
}
/**
if (rc)
goto out;
+ nx_driver.of.status = NX_OKAY;
+
rc = crypto_register_alg(&nx_ecb_aes_alg);
if (rc)
goto out;
if (rc)
goto out_unreg_s512;
- nx_driver.of.status = NX_OKAY;
-
goto out;
out_unreg_s512:
* Based on of-dma.c
*
* Copyright (C) 2013, Intel Corporation
- * Author: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
+ * Authors: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
+ * Mika Westerberg <mika.westerberg@linux.intel.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
#include <linux/list.h>
#include <linux/mutex.h>
#include <linux/slab.h>
+#include <linux/ioport.h>
#include <linux/acpi.h>
#include <linux/acpi_dma.h>
static LIST_HEAD(acpi_dma_list);
static DEFINE_MUTEX(acpi_dma_lock);
+/**
+ * acpi_dma_parse_resource_group - match device and parse resource group
+ * @grp: CSRT resource group
+ * @adev: ACPI device to match with
+ * @adma: struct acpi_dma of the given DMA controller
+ *
+ * Returns 1 on success, 0 when no information is available, or appropriate
+ * errno value on error.
+ *
+ * In order to match a device from DSDT table to the corresponding CSRT device
+ * we use MMIO address and IRQ.
+ */
+static int acpi_dma_parse_resource_group(const struct acpi_csrt_group *grp,
+ struct acpi_device *adev, struct acpi_dma *adma)
+{
+ const struct acpi_csrt_shared_info *si;
+ struct list_head resource_list;
+ struct resource_list_entry *rentry;
+ resource_size_t mem = 0, irq = 0;
+ u32 vendor_id;
+ int ret;
+
+ if (grp->shared_info_length != sizeof(struct acpi_csrt_shared_info))
+ return -ENODEV;
+
+ INIT_LIST_HEAD(&resource_list);
+ ret = acpi_dev_get_resources(adev, &resource_list, NULL, NULL);
+ if (ret <= 0)
+ return 0;
+
+ list_for_each_entry(rentry, &resource_list, node) {
+ if (resource_type(&rentry->res) == IORESOURCE_MEM)
+ mem = rentry->res.start;
+ else if (resource_type(&rentry->res) == IORESOURCE_IRQ)
+ irq = rentry->res.start;
+ }
+
+ acpi_dev_free_resource_list(&resource_list);
+
+ /* Consider initial zero values as resource not found */
+ if (mem == 0 && irq == 0)
+ return 0;
+
+ si = (const struct acpi_csrt_shared_info *)&grp[1];
+
+ /* Match device by MMIO and IRQ */
+ if (si->mmio_base_low != mem || si->gsi_interrupt != irq)
+ return 0;
+
+ vendor_id = le32_to_cpu(grp->vendor_id);
+ dev_dbg(&adev->dev, "matches with %.4s%04X (rev %u)\n",
+ (char *)&vendor_id, grp->device_id, grp->revision);
+
+ /* Check if the request line range is available */
+ if (si->base_request_line == 0 && si->num_handshake_signals == 0)
+ return 0;
+
+ adma->base_request_line = si->base_request_line;
+ adma->end_request_line = si->base_request_line +
+ si->num_handshake_signals - 1;
+
+ dev_dbg(&adev->dev, "request line base: 0x%04x end: 0x%04x\n",
+ adma->base_request_line, adma->end_request_line);
+
+ return 1;
+}
+
+/**
+ * acpi_dma_parse_csrt - parse CSRT to exctract additional DMA resources
+ * @adev: ACPI device to match with
+ * @adma: struct acpi_dma of the given DMA controller
+ *
+ * CSRT or Core System Resources Table is a proprietary ACPI table
+ * introduced by Microsoft. This table can contain devices that are not in
+ * the system DSDT table. In particular DMA controllers might be described
+ * here.
+ *
+ * We are using this table to get the request line range of the specific DMA
+ * controller to be used later.
+ *
+ */
+static void acpi_dma_parse_csrt(struct acpi_device *adev, struct acpi_dma *adma)
+{
+ struct acpi_csrt_group *grp, *end;
+ struct acpi_table_csrt *csrt;
+ acpi_status status;
+ int ret;
+
+ status = acpi_get_table(ACPI_SIG_CSRT, 0,
+ (struct acpi_table_header **)&csrt);
+ if (ACPI_FAILURE(status)) {
+ if (status != AE_NOT_FOUND)
+ dev_warn(&adev->dev, "failed to get the CSRT table\n");
+ return;
+ }
+
+ grp = (struct acpi_csrt_group *)(csrt + 1);
+ end = (struct acpi_csrt_group *)((void *)csrt + csrt->header.length);
+
+ while (grp < end) {
+ ret = acpi_dma_parse_resource_group(grp, adev, adma);
+ if (ret < 0) {
+ dev_warn(&adev->dev,
+ "error in parsing resource group\n");
+ return;
+ }
+
+ grp = (struct acpi_csrt_group *)((void *)grp + grp->length);
+ }
+}
+
/**
* acpi_dma_controller_register - Register a DMA controller to ACPI DMA helpers
* @dev: struct device of DMA controller
adma->acpi_dma_xlate = acpi_dma_xlate;
adma->data = data;
+ acpi_dma_parse_csrt(adev, adma);
+
/* Now queue acpi_dma controller structure in list */
mutex_lock(&acpi_dma_lock);
list_add_tail(&adma->dma_controllers, &acpi_dma_list);
}
EXPORT_SYMBOL_GPL(devm_acpi_dma_controller_free);
+/**
+ * acpi_dma_update_dma_spec - prepare dma specifier to pass to translation function
+ * @adma: struct acpi_dma of DMA controller
+ * @dma_spec: dma specifier to update
+ *
+ * Returns 0, if no information is avaiable, -1 on mismatch, and 1 otherwise.
+ *
+ * Accordingly to ACPI 5.0 Specification Table 6-170 "Fixed DMA Resource
+ * Descriptor":
+ * DMA Request Line bits is a platform-relative number uniquely
+ * identifying the request line assigned. Request line-to-Controller
+ * mapping is done in a controller-specific OS driver.
+ * That's why we can safely adjust slave_id when the appropriate controller is
+ * found.
+ */
+static int acpi_dma_update_dma_spec(struct acpi_dma *adma,
+ struct acpi_dma_spec *dma_spec)
+{
+ /* Set link to the DMA controller device */
+ dma_spec->dev = adma->dev;
+
+ /* Check if the request line range is available */
+ if (adma->base_request_line == 0 && adma->end_request_line == 0)
+ return 0;
+
+ /* Check if slave_id falls to the range */
+ if (dma_spec->slave_id < adma->base_request_line ||
+ dma_spec->slave_id > adma->end_request_line)
+ return -1;
+
+ /*
+ * Here we adjust slave_id. It should be a relative number to the base
+ * request line.
+ */
+ dma_spec->slave_id -= adma->base_request_line;
+
+ return 1;
+}
+
struct acpi_dma_parser_data {
struct acpi_dma_spec dma_spec;
size_t index;
struct acpi_device *adev;
struct acpi_dma *adma;
struct dma_chan *chan = NULL;
+ int found;
/* Check if the device was enumerated by ACPI */
if (!dev || !ACPI_HANDLE(dev))
mutex_lock(&acpi_dma_lock);
list_for_each_entry(adma, &acpi_dma_list, dma_controllers) {
- dma_spec->dev = adma->dev;
+ /*
+ * We are not going to call translation function if slave_id
+ * doesn't fall to the request range.
+ */
+ found = acpi_dma_update_dma_spec(adma, dma_spec);
+ if (found < 0)
+ continue;
chan = adma->acpi_dma_xlate(dma_spec, adma);
- if (chan)
+ /*
+ * Try to get a channel only from the DMA controller that
+ * matches the slave_id. See acpi_dma_update_dma_spec()
+ * description for the details.
+ */
+ if (found > 0 || chan)
break;
}
}
dma_async_issue_pending(chan);
- wait_event_freezable_timeout(done_wait,
- done.done || kthread_should_stop(),
+ wait_event_freezable_timeout(done_wait, done.done,
msecs_to_jiffies(params->timeout));
status = dma_async_is_tx_complete(chan, cookie, NULL, NULL);
static int __restart_threaded_test(struct dmatest_info *info, bool run)
{
struct dmatest_params *params = &info->params;
- int ret;
/* Stop any running test first */
__stop_threaded_test(info);
memcpy(params, &info->dbgfs_params, sizeof(*params));
/* Run test with new parameters */
- ret = __run_threaded_test(info);
- if (ret) {
- __stop_threaded_test(info);
- pr_err("dmatest: Can't run test\n");
+ return __run_threaded_test(info);
+}
+
+static bool __is_threaded_test_run(struct dmatest_info *info)
+{
+ struct dmatest_chan *dtc;
+
+ list_for_each_entry(dtc, &info->channels, node) {
+ struct dmatest_thread *thread;
+
+ list_for_each_entry(thread, &dtc->threads, node) {
+ if (!thread->done)
+ return true;
+ }
}
- return ret;
+ return false;
}
static ssize_t dtf_write_string(void *to, size_t available, loff_t *ppos,
{
struct dmatest_info *info = file->private_data;
char buf[3];
- struct dmatest_chan *dtc;
- bool alive = false;
mutex_lock(&info->lock);
- list_for_each_entry(dtc, &info->channels, node) {
- struct dmatest_thread *thread;
-
- list_for_each_entry(thread, &dtc->threads, node) {
- if (!thread->done) {
- alive = true;
- break;
- }
- }
- }
- if (alive) {
+ if (__is_threaded_test_run(info)) {
buf[0] = 'Y';
} else {
__stop_threaded_test(info);
if (strtobool(buf, &bv) == 0) {
mutex_lock(&info->lock);
- ret = __restart_threaded_test(info, bv);
+
+ if (__is_threaded_test_run(info))
+ ret = -EBUSY;
+ else
+ ret = __restart_threaded_test(info, bv);
+
mutex_unlock(&info->lock);
}
return;
}
- if (d40_queue_start(d40c) == NULL)
+ if (d40_queue_start(d40c) == NULL) {
d40c->busy = false;
- pm_runtime_mark_last_busy(d40c->base->dev);
- pm_runtime_put_autosuspend(d40c->base->dev);
+
+ pm_runtime_mark_last_busy(d40c->base->dev);
+ pm_runtime_put_autosuspend(d40c->base->dev);
+ }
d40_desc_remove(d40d);
d40_desc_done(d40c, d40d);
amd64_inject_word_show, amd64_inject_word_store);
static DEVICE_ATTR(inject_ecc_vector, S_IRUGO | S_IWUSR,
amd64_inject_ecc_vector_show, amd64_inject_ecc_vector_store);
-static DEVICE_ATTR(inject_write, S_IRUGO | S_IWUSR,
+static DEVICE_ATTR(inject_write, S_IWUSR,
NULL, amd64_inject_write_store);
-static DEVICE_ATTR(inject_read, S_IRUGO | S_IWUSR,
+static DEVICE_ATTR(inject_read, S_IWUSR,
NULL, amd64_inject_read_store);
struct efivar_entry *entry;
int err;
- entry = kzalloc(sizeof(*entry), GFP_KERNEL);
- if (!entry)
- return;
-
/* Add new sysfs entries */
while (1) {
- memset(entry, 0, sizeof(*entry));
+ entry = kzalloc(sizeof(*entry), GFP_KERNEL);
+ if (!entry)
+ return;
err = efivar_init(efivar_update_sysfs_entry, entry,
true, false, &efivar_sysfs_list);
config GPIO_MCP23S08
tristate "Microchip MCP23xxx I/O expander"
- depends on SPI_MASTER || I2C
+ depends on (SPI_MASTER && !I2C) || I2C
help
SPI/I2C driver for Microchip MCP23S08/MCP23S17/MCP23008/MCP23017
I/O expanders.
resource_size_t start, len;
struct lnw_gpio *lnw;
u32 gpio_base;
+ u32 irq_base;
int retval;
int ngpio = id->driver_data;
retval = -EFAULT;
goto err_ioremap;
}
+ irq_base = *(u32 *)base;
gpio_base = *((u32 *)base + 1);
/* release the IO mapping, since we already get the info from bar1 */
iounmap(base);
goto err_ioremap;
}
- lnw->domain = irq_domain_add_linear(pdev->dev.of_node, ngpio,
- &lnw_gpio_irq_ops, lnw);
- if (!lnw->domain) {
- retval = -ENOMEM;
- goto err_ioremap;
- }
-
lnw->reg_base = base;
lnw->chip.label = dev_name(&pdev->dev);
lnw->chip.request = lnw_gpio_request;
lnw->chip.ngpio = ngpio;
lnw->chip.can_sleep = 0;
lnw->pdev = pdev;
+
+ lnw->domain = irq_domain_add_simple(pdev->dev.of_node, ngpio, irq_base,
+ &lnw_gpio_irq_ops, lnw);
+ if (!lnw->domain) {
+ retval = -ENOMEM;
+ goto err_ioremap;
+ }
+
pci_set_drvdata(pdev, lnw);
retval = gpiochip_add(&lnw->chip);
if (retval) {
err_gpiochip_add:
while (--i >= 0) {
chip--;
- ret = gpiochip_remove(&chip->gpio);
- if (ret)
+ if (gpiochip_remove(&chip->gpio))
dev_err(&pdev->dev, "Failed gpiochip_remove(%d)\n", i);
}
kfree(chip_save);
err = bgpio_init(&port->bgc, &pdev->dev, 4,
port->base + PINCTRL_DIN(port),
- port->base + PINCTRL_DOUT(port), NULL,
+ port->base + PINCTRL_DOUT(port) + MXS_SET,
+ port->base + PINCTRL_DOUT(port) + MXS_CLR,
port->base + PINCTRL_DOE(port), NULL, 0);
if (err)
goto out_irqdesc_free;
bool is_mpuio;
bool dbck_flag;
bool loses_context;
+ bool context_valid;
int stride;
u32 width;
int context_loss_count;
bank->loses_context = true;
} else {
bank->loses_context = pdata->loses_context;
+
+ if (bank->loses_context)
+ bank->get_context_loss_count =
+ pdata->get_context_loss_count;
}
omap_gpio_chip_init(bank);
omap_gpio_show_rev(bank);
- if (bank->loses_context)
- bank->get_context_loss_count = pdata->get_context_loss_count;
-
pm_runtime_put(bank->dev);
list_add_tail(&bank->node, &omap_gpio_list);
return 0;
}
+static void omap_gpio_init_context(struct gpio_bank *p);
+
static int omap_gpio_runtime_resume(struct device *dev)
{
struct platform_device *pdev = to_platform_device(dev);
int c;
spin_lock_irqsave(&bank->lock, flags);
+
+ /*
+ * On the first resume during the probe, the context has not
+ * been initialised and so initialise it now. Also initialise
+ * the context loss count.
+ */
+ if (bank->loses_context && !bank->context_valid) {
+ omap_gpio_init_context(bank);
+
+ if (bank->get_context_loss_count)
+ bank->context_loss_count =
+ bank->get_context_loss_count(bank->dev);
+ }
+
_gpio_dbck_enable(bank);
/*
}
#if defined(CONFIG_PM_RUNTIME)
+static void omap_gpio_init_context(struct gpio_bank *p)
+{
+ struct omap_gpio_reg_offs *regs = p->regs;
+ void __iomem *base = p->base;
+
+ p->context.ctrl = __raw_readl(base + regs->ctrl);
+ p->context.oe = __raw_readl(base + regs->direction);
+ p->context.wake_en = __raw_readl(base + regs->wkup_en);
+ p->context.leveldetect0 = __raw_readl(base + regs->leveldetect0);
+ p->context.leveldetect1 = __raw_readl(base + regs->leveldetect1);
+ p->context.risingdetect = __raw_readl(base + regs->risingdetect);
+ p->context.fallingdetect = __raw_readl(base + regs->fallingdetect);
+ p->context.irqenable1 = __raw_readl(base + regs->irqenable);
+ p->context.irqenable2 = __raw_readl(base + regs->irqenable2);
+
+ if (regs->set_dataout && p->regs->clr_dataout)
+ p->context.dataout = __raw_readl(base + regs->set_dataout);
+ else
+ p->context.dataout = __raw_readl(base + regs->dataout);
+
+ p->context_valid = true;
+}
+
static void omap_gpio_restore_context(struct gpio_bank *bank)
{
__raw_writel(bank->context.wake_en,
#else
#define omap_gpio_runtime_suspend NULL
#define omap_gpio_runtime_resume NULL
+static void omap_gpio_init_context(struct gpio_bank *p) {}
#endif
static const struct dev_pm_ops gpio_pm_ops = {
err_request_irq:
irq_free_descs(irq_base, gpio_pins[chip->ioh]);
- ret = gpiochip_remove(&chip->gpio);
- if (ret)
+ if (gpiochip_remove(&chip->gpio))
dev_err(&pdev->dev, "%s gpiochip_remove failed\n", __func__);
err_gpiochip_add:
return 0;
err_sch_gpio_resume:
- err = gpiochip_remove(&sch_gpio_core);
- if (err)
- dev_err(&pdev->dev, "%s failed, %d\n",
- "gpiochip_remove()", err);
+ if (gpiochip_remove(&sch_gpio_core))
+ dev_err(&pdev->dev, "%s gpiochip_remove failed\n", __func__);
err_sch_gpio_core:
release_region(res->start, resource_size(res));
return ret;
err_gpiob:
- ret = gpiochip_remove(&vb_gpio->gpioa);
+ if (gpiochip_remove(&vb_gpio->gpioa))
+ dev_err(&pdev->dev, "%s gpiochip_remove failed\n", __func__);
err_gpioa:
return ret;
*/
void drm_vblank_pre_modeset(struct drm_device *dev, int crtc)
{
- /* vblank is not initialized (IRQ not installed ?) */
+ /* vblank is not initialized (IRQ not installed ?), or has been freed */
if (!dev->num_crtcs)
return;
/*
{
unsigned long irqflags;
+ /* vblank is not initialized (IRQ not installed ?), or has been freed */
+ if (!dev->num_crtcs)
+ return;
+
if (dev->vblank_inmodeset[crtc]) {
spin_lock_irqsave(&dev->vbl_lock, irqflags);
dev->vblank_disable_allowed = 1;
unsigned int pipe;
unsigned int dpms;
enum exynos_crtc_mode mode;
+ wait_queue_head_t pending_flip_queue;
+ atomic_t pending_flip;
};
static void exynos_drm_crtc_dpms(struct drm_crtc *crtc, int mode)
return;
}
+ if (mode > DRM_MODE_DPMS_ON) {
+ /* wait for the completion of page flip. */
+ wait_event(exynos_crtc->pending_flip_queue,
+ atomic_read(&exynos_crtc->pending_flip) == 0);
+ drm_vblank_off(crtc->dev, exynos_crtc->pipe);
+ }
+
exynos_drm_fn_encoder(crtc, &mode, exynos_drm_encoder_crtc_dpms);
exynos_crtc->dpms = mode;
}
ret = drm_vblank_get(dev, exynos_crtc->pipe);
if (ret) {
DRM_DEBUG("failed to acquire vblank counter\n");
- list_del(&event->base.link);
goto out;
}
spin_lock_irq(&dev->event_lock);
list_add_tail(&event->base.link,
&dev_priv->pageflip_event_list);
+ atomic_set(&exynos_crtc->pending_flip, 1);
spin_unlock_irq(&dev->event_lock);
crtc->fb = fb;
exynos_crtc->pipe = nr;
exynos_crtc->dpms = DRM_MODE_DPMS_OFF;
+ init_waitqueue_head(&exynos_crtc->pending_flip_queue);
+ atomic_set(&exynos_crtc->pending_flip, 0);
exynos_crtc->plane = exynos_plane_init(dev, 1 << nr, true);
if (!exynos_crtc->plane) {
kfree(exynos_crtc);
{
struct exynos_drm_private *dev_priv = dev->dev_private;
struct drm_pending_vblank_event *e, *t;
- struct timeval now;
+ struct drm_crtc *drm_crtc = dev_priv->crtc[crtc];
+ struct exynos_drm_crtc *exynos_crtc = to_exynos_crtc(drm_crtc);
unsigned long flags;
DRM_DEBUG_KMS("%s\n", __FILE__);
if (crtc != e->pipe)
continue;
- do_gettimeofday(&now);
- e->event.sequence = 0;
- e->event.tv_sec = now.tv_sec;
- e->event.tv_usec = now.tv_usec;
-
- list_move_tail(&e->base.link, &e->base.file_priv->event_list);
- wake_up_interruptible(&e->base.file_priv->event_wait);
+ list_del(&e->base.link);
+ drm_send_vblank_event(dev, -1, e);
drm_vblank_put(dev, crtc);
+ atomic_set(&exynos_crtc->pending_flip, 0);
+ wake_up(&exynos_crtc->pending_flip_queue);
}
spin_unlock_irqrestore(&dev->event_lock, flags);
helper->fb = exynos_drm_framebuffer_init(dev, &mode_cmd,
&exynos_gem_obj->base);
- if (IS_ERR_OR_NULL(helper->fb)) {
+ if (IS_ERR(helper->fb)) {
DRM_ERROR("failed to create drm framebuffer.\n");
ret = PTR_ERR(helper->fb);
goto err_destroy_gem;
*
*/
#include <linux/kernel.h>
-#include <linux/mfd/syscon.h>
#include <linux/module.h>
#include <linux/platform_device.h>
+#include <linux/mfd/syscon.h>
#include <linux/regmap.h>
#include <linux/clk.h>
#include <linux/pm_runtime.h>
}
ctx->irq = res->start;
- ret = request_threaded_irq(ctx->irq, NULL, fimc_irq_handler,
+ ret = devm_request_threaded_irq(dev, ctx->irq, NULL, fimc_irq_handler,
IRQF_ONESHOT, "drm_fimc", ctx);
if (ret < 0) {
dev_err(dev, "failed to request irq.\n");
ret = fimc_setup_clocks(ctx);
if (ret < 0)
- goto err_free_irq;
+ return ret;
ippdrv = &ctx->ippdrv;
ippdrv->ops[EXYNOS_DRM_OPS_SRC] = &fimc_src_ops;
goto err_pm_dis;
}
- dev_info(&pdev->dev, "drm fimc registered successfully.\n");
+ dev_info(dev, "drm fimc registered successfully.\n");
return 0;
pm_runtime_disable(dev);
err_put_clk:
fimc_put_clocks(ctx);
-err_free_irq:
- free_irq(ctx->irq, ctx);
return ret;
}
pm_runtime_set_suspended(dev);
pm_runtime_disable(dev);
- free_irq(ctx->irq, ctx);
-
return 0;
}
DRM_DEBUG_KMS("%s\n", __FILE__);
- if (pdev->dev.of_node) {
+ if (dev->of_node) {
pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL);
if (!pdata) {
DRM_ERROR("memory allocation for pdata failed\n");
return ret;
}
} else {
- pdata = pdev->dev.platform_data;
+ pdata = dev->platform_data;
if (!pdata) {
DRM_ERROR("no platform data specified\n");
return -EINVAL;
return -EINVAL;
}
- ctx = devm_kzalloc(&pdev->dev, sizeof(*ctx), GFP_KERNEL);
+ ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
if (!ctx)
return -ENOMEM;
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- ctx->regs = devm_ioremap_resource(&pdev->dev, res);
+ ctx->regs = devm_ioremap_resource(dev, res);
if (IS_ERR(ctx->regs))
return PTR_ERR(ctx->regs);
ctx->irq = res->start;
- ret = devm_request_irq(&pdev->dev, ctx->irq, fimd_irq_handler,
+ ret = devm_request_irq(dev, ctx->irq, fimd_irq_handler,
0, "drm_fimd", ctx);
if (ret) {
dev_err(dev, "irq request failed.\n");
struct exynos_drm_subdrv *subdrv;
int ret;
- g2d = devm_kzalloc(&pdev->dev, sizeof(*g2d), GFP_KERNEL);
+ g2d = devm_kzalloc(dev, sizeof(*g2d), GFP_KERNEL);
if (!g2d) {
dev_err(dev, "failed to allocate driver data\n");
return -ENOMEM;
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- g2d->regs = devm_ioremap_resource(&pdev->dev, res);
+ g2d->regs = devm_ioremap_resource(dev, res);
if (IS_ERR(g2d->regs)) {
ret = PTR_ERR(g2d->regs);
goto err_put_clk;
goto err_put_clk;
}
- ret = devm_request_irq(&pdev->dev, g2d->irq, g2d_irq_handler, 0,
+ ret = devm_request_irq(dev, g2d->irq, g2d_irq_handler, 0,
"drm_g2d", g2d);
if (ret < 0) {
dev_err(dev, "irq request failed\n");
}
ctx->irq = res->start;
- ret = request_threaded_irq(ctx->irq, NULL, gsc_irq_handler,
+ ret = devm_request_threaded_irq(dev, ctx->irq, NULL, gsc_irq_handler,
IRQF_ONESHOT, "drm_gsc", ctx);
if (ret < 0) {
dev_err(dev, "failed to request irq.\n");
ret = gsc_init_prop_list(ippdrv);
if (ret < 0) {
dev_err(dev, "failed to init property list.\n");
- goto err_get_irq;
+ return ret;
}
DRM_DEBUG_KMS("%s:id[%d]ippdrv[0x%x]\n", __func__, ctx->id,
goto err_ippdrv_register;
}
- dev_info(&pdev->dev, "drm gsc registered successfully.\n");
+ dev_info(dev, "drm gsc registered successfully.\n");
return 0;
err_ippdrv_register:
- devm_kfree(dev, ippdrv->prop_list);
pm_runtime_disable(dev);
-err_get_irq:
- free_irq(ctx->irq, ctx);
return ret;
}
struct gsc_context *ctx = get_gsc_context(dev);
struct exynos_drm_ippdrv *ippdrv = &ctx->ippdrv;
- devm_kfree(dev, ippdrv->prop_list);
exynos_drm_ippdrv_unregister(ippdrv);
mutex_destroy(&ctx->lock);
pm_runtime_set_suspended(dev);
pm_runtime_disable(dev);
- free_irq(ctx->irq, ctx);
-
return 0;
}
DRM_DEBUG_KMS("%s\n", __FILE__);
- ctx = devm_kzalloc(&pdev->dev, sizeof(*ctx), GFP_KERNEL);
+ ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
if (!ctx) {
DRM_LOG_KMS("failed to alloc common hdmi context.\n");
return -ENOMEM;
/* find ipp driver using idr */
ippdrv = ipp_find_obj(&ctx->ipp_idr, &ctx->ipp_lock,
ipp_id);
- if (IS_ERR_OR_NULL(ippdrv)) {
+ if (IS_ERR(ippdrv)) {
DRM_ERROR("not found ipp%d driver.\n", ipp_id);
return ippdrv;
}
DRM_DEBUG_KMS("%s:prop_id[%d]\n", __func__, prop_id);
ippdrv = ipp_find_drv_by_handle(prop_id);
- if (IS_ERR_OR_NULL(ippdrv)) {
+ if (IS_ERR(ippdrv)) {
DRM_ERROR("failed to get ipp driver.\n");
return -EINVAL;
}
/* find ipp driver using ipp id */
ippdrv = ipp_find_driver(ctx, property);
- if (IS_ERR_OR_NULL(ippdrv)) {
+ if (IS_ERR(ippdrv)) {
DRM_ERROR("failed to get ipp driver.\n");
return -EINVAL;
}
c_node->state = IPP_STATE_IDLE;
c_node->start_work = ipp_create_cmd_work();
- if (IS_ERR_OR_NULL(c_node->start_work)) {
+ if (IS_ERR(c_node->start_work)) {
DRM_ERROR("failed to create start work.\n");
goto err_clear;
}
c_node->stop_work = ipp_create_cmd_work();
- if (IS_ERR_OR_NULL(c_node->stop_work)) {
+ if (IS_ERR(c_node->stop_work)) {
DRM_ERROR("failed to create stop work.\n");
goto err_free_start;
}
c_node->event_work = ipp_create_event_work();
- if (IS_ERR_OR_NULL(c_node->event_work)) {
+ if (IS_ERR(c_node->event_work)) {
DRM_ERROR("failed to create event work.\n");
goto err_free_stop;
}
DRM_DEBUG_KMS("%s\n", __func__);
ippdrv = ipp_find_drv_by_handle(qbuf->prop_id);
- if (IS_ERR_OR_NULL(ippdrv)) {
+ if (IS_ERR(ippdrv)) {
DRM_ERROR("failed to get ipp driver.\n");
return -EFAULT;
}
struct exynos_drm_subdrv *subdrv;
int ret;
- ctx = devm_kzalloc(&pdev->dev, sizeof(*ctx), GFP_KERNEL);
+ ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
if (!ctx)
return -ENOMEM;
goto err_cmd_workq;
}
- dev_info(&pdev->dev, "drm ipp registered successfully.\n");
+ dev_info(dev, "drm ipp registered successfully.\n");
return 0;
return rot->irq;
}
- ret = request_threaded_irq(rot->irq, NULL, rotator_irq_handler,
- IRQF_ONESHOT, "drm_rotator", rot);
+ ret = devm_request_threaded_irq(dev, rot->irq, NULL,
+ rotator_irq_handler, IRQF_ONESHOT, "drm_rotator", rot);
if (ret < 0) {
dev_err(dev, "failed to request irq\n");
return ret;
rot->clock = devm_clk_get(dev, "rotator");
if (IS_ERR(rot->clock)) {
dev_err(dev, "failed to get clock\n");
- ret = PTR_ERR(rot->clock);
- goto err_clk_get;
+ return PTR_ERR(rot->clock);
}
pm_runtime_enable(dev);
return 0;
err_ippdrv_register:
- devm_kfree(dev, ippdrv->prop_list);
pm_runtime_disable(dev);
-err_clk_get:
- free_irq(rot->irq, rot);
return ret;
}
struct rot_context *rot = dev_get_drvdata(dev);
struct exynos_drm_ippdrv *ippdrv = &rot->ippdrv;
- devm_kfree(dev, ippdrv->prop_list);
exynos_drm_ippdrv_unregister(ippdrv);
pm_runtime_disable(dev);
- free_irq(rot->irq, rot);
-
return 0;
}
DRM_DEBUG_KMS("%s\n", __FILE__);
- ctx = devm_kzalloc(&pdev->dev, sizeof(*ctx), GFP_KERNEL);
+ ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
if (!ctx)
return -ENOMEM;
platform_set_drvdata(pdev, ctx);
- ret = device_create_file(&pdev->dev, &dev_attr_connection);
+ ret = device_create_file(dev, &dev_attr_connection);
if (ret < 0)
DRM_INFO("failed to create connection sysfs.\n");
DRM_DEBUG_KMS("[%d]\n", __LINE__);
- if (pdev->dev.of_node) {
+ if (dev->of_node) {
pdata = drm_hdmi_dt_parse_pdata(dev);
if (IS_ERR(pdata)) {
DRM_ERROR("failed to parse dt\n");
return PTR_ERR(pdata);
}
} else {
- pdata = pdev->dev.platform_data;
+ pdata = dev->platform_data;
}
if (!pdata) {
return -EINVAL;
}
- drm_hdmi_ctx = devm_kzalloc(&pdev->dev, sizeof(*drm_hdmi_ctx),
+ drm_hdmi_ctx = devm_kzalloc(dev, sizeof(*drm_hdmi_ctx),
GFP_KERNEL);
if (!drm_hdmi_ctx) {
DRM_ERROR("failed to allocate common hdmi context.\n");
return -ENOMEM;
}
- hdata = devm_kzalloc(&pdev->dev, sizeof(struct hdmi_context),
+ hdata = devm_kzalloc(dev, sizeof(struct hdmi_context),
GFP_KERNEL);
if (!hdata) {
DRM_ERROR("out of memory\n");
if (dev->of_node) {
const struct of_device_id *match;
match = of_match_node(of_match_ptr(hdmi_match_types),
- pdev->dev.of_node);
+ dev->of_node);
if (match == NULL)
return -ENODEV;
hdata->type = (enum hdmi_type)match->data;
}
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- hdata->regs = devm_ioremap_resource(&pdev->dev, res);
+ hdata->regs = devm_ioremap_resource(dev, res);
if (IS_ERR(hdata->regs))
return PTR_ERR(hdata->regs);
- ret = devm_gpio_request(&pdev->dev, hdata->hpd_gpio, "HPD");
+ ret = devm_gpio_request(dev, hdata->hpd_gpio, "HPD");
if (ret) {
DRM_ERROR("failed to request HPD gpio\n");
return ret;
hdata->hpd = gpio_get_value(hdata->hpd_gpio);
- ret = request_threaded_irq(hdata->irq, NULL,
+ ret = devm_request_threaded_irq(dev, hdata->irq, NULL,
hdmi_irq_thread, IRQF_TRIGGER_RISING |
IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
"hdmi", drm_hdmi_ctx);
static int hdmi_remove(struct platform_device *pdev)
{
struct device *dev = &pdev->dev;
- struct exynos_drm_hdmi_context *ctx = platform_get_drvdata(pdev);
- struct hdmi_context *hdata = ctx->ctx;
DRM_DEBUG_KMS("[%d] %s\n", __LINE__, __func__);
pm_runtime_disable(dev);
- free_irq(hdata->irq, hdata);
-
-
/* hdmiphy i2c driver */
i2c_del_driver(&hdmiphy_driver);
/* DDC i2c driver */
return -ENXIO;
}
- mixer_res->mixer_regs = devm_ioremap(&pdev->dev, res->start,
+ mixer_res->mixer_regs = devm_ioremap(dev, res->start,
resource_size(res));
if (mixer_res->mixer_regs == NULL) {
dev_err(dev, "register mapping failed.\n");
return -ENXIO;
}
- ret = devm_request_irq(&pdev->dev, res->start, mixer_irq_handler,
+ ret = devm_request_irq(dev, res->start, mixer_irq_handler,
0, "drm_mixer", ctx);
if (ret) {
dev_err(dev, "request interrupt failed.\n");
return -ENXIO;
}
- mixer_res->vp_regs = devm_ioremap(&pdev->dev, res->start,
+ mixer_res->vp_regs = devm_ioremap(dev, res->start,
resource_size(res));
if (mixer_res->vp_regs == NULL) {
dev_err(dev, "register mapping failed.\n");
dev_info(dev, "probe start\n");
- drm_hdmi_ctx = devm_kzalloc(&pdev->dev, sizeof(*drm_hdmi_ctx),
+ drm_hdmi_ctx = devm_kzalloc(dev, sizeof(*drm_hdmi_ctx),
GFP_KERNEL);
if (!drm_hdmi_ctx) {
DRM_ERROR("failed to allocate common hdmi context.\n");
return -ENOMEM;
}
- ctx = devm_kzalloc(&pdev->dev, sizeof(*ctx), GFP_KERNEL);
+ ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
if (!ctx) {
DRM_ERROR("failed to alloc mixer context.\n");
return -ENOMEM;
if (dev->of_node) {
const struct of_device_id *match;
match = of_match_node(of_match_ptr(mixer_match_types),
- pdev->dev.of_node);
+ dev->of_node);
drv = (struct mixer_drv_data *)match->data;
} else {
drv = (struct mixer_drv_data *)
platform_get_device_id(pdev)->driver_data;
}
- ctx->dev = &pdev->dev;
+ ctx->dev = dev;
ctx->parent_ctx = (void *)drm_hdmi_ctx;
drm_hdmi_ctx->ctx = (void *)ctx;
ctx->vp_enabled = drv->is_vp_enabled;
INTEL_VGA_DEVICE(0x016a, &intel_ivybridge_d_info), /* GT2 server */
INTEL_VGA_DEVICE(0x0402, &intel_haswell_d_info), /* GT1 desktop */
INTEL_VGA_DEVICE(0x0412, &intel_haswell_d_info), /* GT2 desktop */
- INTEL_VGA_DEVICE(0x0422, &intel_haswell_d_info), /* GT2 desktop */
+ INTEL_VGA_DEVICE(0x0422, &intel_haswell_d_info), /* GT3 desktop */
INTEL_VGA_DEVICE(0x040a, &intel_haswell_d_info), /* GT1 server */
INTEL_VGA_DEVICE(0x041a, &intel_haswell_d_info), /* GT2 server */
- INTEL_VGA_DEVICE(0x042a, &intel_haswell_d_info), /* GT2 server */
+ INTEL_VGA_DEVICE(0x042a, &intel_haswell_d_info), /* GT3 server */
INTEL_VGA_DEVICE(0x0406, &intel_haswell_m_info), /* GT1 mobile */
INTEL_VGA_DEVICE(0x0416, &intel_haswell_m_info), /* GT2 mobile */
INTEL_VGA_DEVICE(0x0426, &intel_haswell_m_info), /* GT2 mobile */
+ INTEL_VGA_DEVICE(0x040B, &intel_haswell_d_info), /* GT1 reserved */
+ INTEL_VGA_DEVICE(0x041B, &intel_haswell_d_info), /* GT2 reserved */
+ INTEL_VGA_DEVICE(0x042B, &intel_haswell_d_info), /* GT3 reserved */
+ INTEL_VGA_DEVICE(0x040E, &intel_haswell_d_info), /* GT1 reserved */
+ INTEL_VGA_DEVICE(0x041E, &intel_haswell_d_info), /* GT2 reserved */
+ INTEL_VGA_DEVICE(0x042E, &intel_haswell_d_info), /* GT3 reserved */
INTEL_VGA_DEVICE(0x0C02, &intel_haswell_d_info), /* SDV GT1 desktop */
INTEL_VGA_DEVICE(0x0C12, &intel_haswell_d_info), /* SDV GT2 desktop */
- INTEL_VGA_DEVICE(0x0C22, &intel_haswell_d_info), /* SDV GT2 desktop */
+ INTEL_VGA_DEVICE(0x0C22, &intel_haswell_d_info), /* SDV GT3 desktop */
INTEL_VGA_DEVICE(0x0C0A, &intel_haswell_d_info), /* SDV GT1 server */
INTEL_VGA_DEVICE(0x0C1A, &intel_haswell_d_info), /* SDV GT2 server */
- INTEL_VGA_DEVICE(0x0C2A, &intel_haswell_d_info), /* SDV GT2 server */
+ INTEL_VGA_DEVICE(0x0C2A, &intel_haswell_d_info), /* SDV GT3 server */
INTEL_VGA_DEVICE(0x0C06, &intel_haswell_m_info), /* SDV GT1 mobile */
INTEL_VGA_DEVICE(0x0C16, &intel_haswell_m_info), /* SDV GT2 mobile */
- INTEL_VGA_DEVICE(0x0C26, &intel_haswell_m_info), /* SDV GT2 mobile */
+ INTEL_VGA_DEVICE(0x0C26, &intel_haswell_m_info), /* SDV GT3 mobile */
+ INTEL_VGA_DEVICE(0x0C0B, &intel_haswell_d_info), /* SDV GT1 reserved */
+ INTEL_VGA_DEVICE(0x0C1B, &intel_haswell_d_info), /* SDV GT2 reserved */
+ INTEL_VGA_DEVICE(0x0C2B, &intel_haswell_d_info), /* SDV GT3 reserved */
+ INTEL_VGA_DEVICE(0x0C0E, &intel_haswell_d_info), /* SDV GT1 reserved */
+ INTEL_VGA_DEVICE(0x0C1E, &intel_haswell_d_info), /* SDV GT2 reserved */
+ INTEL_VGA_DEVICE(0x0C2E, &intel_haswell_d_info), /* SDV GT3 reserved */
INTEL_VGA_DEVICE(0x0A02, &intel_haswell_d_info), /* ULT GT1 desktop */
INTEL_VGA_DEVICE(0x0A12, &intel_haswell_d_info), /* ULT GT2 desktop */
- INTEL_VGA_DEVICE(0x0A22, &intel_haswell_d_info), /* ULT GT2 desktop */
+ INTEL_VGA_DEVICE(0x0A22, &intel_haswell_d_info), /* ULT GT3 desktop */
INTEL_VGA_DEVICE(0x0A0A, &intel_haswell_d_info), /* ULT GT1 server */
INTEL_VGA_DEVICE(0x0A1A, &intel_haswell_d_info), /* ULT GT2 server */
- INTEL_VGA_DEVICE(0x0A2A, &intel_haswell_d_info), /* ULT GT2 server */
+ INTEL_VGA_DEVICE(0x0A2A, &intel_haswell_d_info), /* ULT GT3 server */
INTEL_VGA_DEVICE(0x0A06, &intel_haswell_m_info), /* ULT GT1 mobile */
INTEL_VGA_DEVICE(0x0A16, &intel_haswell_m_info), /* ULT GT2 mobile */
- INTEL_VGA_DEVICE(0x0A26, &intel_haswell_m_info), /* ULT GT2 mobile */
+ INTEL_VGA_DEVICE(0x0A26, &intel_haswell_m_info), /* ULT GT3 mobile */
+ INTEL_VGA_DEVICE(0x0A0B, &intel_haswell_d_info), /* ULT GT1 reserved */
+ INTEL_VGA_DEVICE(0x0A1B, &intel_haswell_d_info), /* ULT GT2 reserved */
+ INTEL_VGA_DEVICE(0x0A2B, &intel_haswell_d_info), /* ULT GT3 reserved */
+ INTEL_VGA_DEVICE(0x0A0E, &intel_haswell_m_info), /* ULT GT1 reserved */
+ INTEL_VGA_DEVICE(0x0A1E, &intel_haswell_m_info), /* ULT GT2 reserved */
+ INTEL_VGA_DEVICE(0x0A2E, &intel_haswell_m_info), /* ULT GT3 reserved */
INTEL_VGA_DEVICE(0x0D02, &intel_haswell_d_info), /* CRW GT1 desktop */
INTEL_VGA_DEVICE(0x0D12, &intel_haswell_d_info), /* CRW GT2 desktop */
- INTEL_VGA_DEVICE(0x0D22, &intel_haswell_d_info), /* CRW GT2 desktop */
+ INTEL_VGA_DEVICE(0x0D22, &intel_haswell_d_info), /* CRW GT3 desktop */
INTEL_VGA_DEVICE(0x0D0A, &intel_haswell_d_info), /* CRW GT1 server */
INTEL_VGA_DEVICE(0x0D1A, &intel_haswell_d_info), /* CRW GT2 server */
- INTEL_VGA_DEVICE(0x0D2A, &intel_haswell_d_info), /* CRW GT2 server */
+ INTEL_VGA_DEVICE(0x0D2A, &intel_haswell_d_info), /* CRW GT3 server */
INTEL_VGA_DEVICE(0x0D06, &intel_haswell_m_info), /* CRW GT1 mobile */
INTEL_VGA_DEVICE(0x0D16, &intel_haswell_m_info), /* CRW GT2 mobile */
- INTEL_VGA_DEVICE(0x0D26, &intel_haswell_m_info), /* CRW GT2 mobile */
+ INTEL_VGA_DEVICE(0x0D26, &intel_haswell_m_info), /* CRW GT3 mobile */
+ INTEL_VGA_DEVICE(0x0D0B, &intel_haswell_d_info), /* CRW GT1 reserved */
+ INTEL_VGA_DEVICE(0x0D1B, &intel_haswell_d_info), /* CRW GT2 reserved */
+ INTEL_VGA_DEVICE(0x0D2B, &intel_haswell_d_info), /* CRW GT3 reserved */
+ INTEL_VGA_DEVICE(0x0D0E, &intel_haswell_d_info), /* CRW GT1 reserved */
+ INTEL_VGA_DEVICE(0x0D1E, &intel_haswell_d_info), /* CRW GT2 reserved */
+ INTEL_VGA_DEVICE(0x0D2E, &intel_haswell_d_info), /* CRW GT3 reserved */
INTEL_VGA_DEVICE(0x0f30, &intel_valleyview_m_info),
INTEL_VGA_DEVICE(0x0f31, &intel_valleyview_m_info),
INTEL_VGA_DEVICE(0x0f32, &intel_valleyview_m_info),
return (void __user *)(uintptr_t)address;
}
+static inline unsigned long msecs_to_jiffies_timeout(const unsigned int m)
+{
+ unsigned long j = msecs_to_jiffies(m);
+
+ return min_t(unsigned long, MAX_JIFFY_OFFSET, j + 1);
+}
+
+static inline unsigned long
+timespec_to_jiffies_timeout(const struct timespec *value)
+{
+ unsigned long j = timespec_to_jiffies(value);
+
+ return min_t(unsigned long, MAX_JIFFY_OFFSET, j + 1);
+}
+
#endif
{
int ret;
-#define EXIT_COND (!i915_reset_in_progress(error))
+#define EXIT_COND (!i915_reset_in_progress(error) || \
+ i915_terminally_wedged(error))
if (EXIT_COND)
return 0;
- /* GPU is already declared terminally dead, give up. */
- if (i915_terminally_wedged(error))
- return -EIO;
-
/*
* Only wait 10 seconds for the gpu reset to complete to avoid hanging
* userspace. If it takes that long something really bad is going on and
wait_forever = false;
}
- timeout_jiffies = timespec_to_jiffies(&wait_time);
+ timeout_jiffies = timespec_to_jiffies_timeout(&wait_time);
if (WARN_ON(!ring->irq_get(ring)))
return -ENODEV;
memset(&pipe_config, 0, sizeof(pipe_config));
active = dev_priv->display.get_pipe_config(crtc,
&pipe_config);
+
+ /* hw state is inconsistent with the pipe A quirk */
+ if (crtc->pipe == PIPE_A && dev_priv->quirks & QUIRK_PIPEA_FORCE)
+ active = crtc->active;
+
WARN(crtc->active != active,
"crtc active state doesn't match with hw state "
"(expected %i, found %i)\n", crtc->active, active);
}
}
+static bool
+is_crtc_connector_off(struct drm_crtc *crtc, struct drm_connector *connectors,
+ int num_connectors)
+{
+ int i;
+
+ for (i = 0; i < num_connectors; i++)
+ if (connectors[i].encoder &&
+ connectors[i].encoder->crtc == crtc &&
+ connectors[i].dpms != DRM_MODE_DPMS_ON)
+ return true;
+
+ return false;
+}
+
static void
intel_set_config_compute_mode_changes(struct drm_mode_set *set,
struct intel_set_config *config)
/* We should be able to check here if the fb has the same properties
* and then just flip_or_move it */
- if (set->crtc->fb != set->fb) {
+ if (set->connectors != NULL &&
+ is_crtc_connector_off(set->crtc, *set->connectors,
+ set->num_connectors)) {
+ config->mode_changed = true;
+ } else if (set->crtc->fb != set->fb) {
/* If we have no fb then treat it as a full mode set */
if (set->crtc->fb == NULL) {
DRM_DEBUG_KMS("crtc has no fb, full mode set\n");
} else if (set->fb->pixel_format !=
set->crtc->fb->pixel_format) {
config->mode_changed = true;
- } else
+ } else {
config->fb_changed = true;
+ }
}
if (set->fb && (set->x != set->crtc->x || set->y != set->crtc->y))
ret = intel_set_mode(set->crtc, set->mode,
set->x, set->y, set->fb);
- if (ret) {
- DRM_ERROR("failed to set mode on [CRTC:%d], err = %d\n",
- set->crtc->base.id, ret);
- goto fail;
- }
} else if (config->fb_changed) {
intel_crtc_wait_for_pending_flips(set->crtc);
set->x, set->y, set->fb);
}
- intel_set_config_free(config);
-
- return 0;
-
+ if (ret) {
+ DRM_ERROR("failed to set mode on [CRTC:%d], err = %d\n",
+ set->crtc->base.id, ret);
fail:
- intel_set_config_restore_state(dev, config);
+ intel_set_config_restore_state(dev, config);
- /* Try to restore the config */
- if (config->mode_changed &&
- intel_set_mode(save_set.crtc, save_set.mode,
- save_set.x, save_set.y, save_set.fb))
- DRM_ERROR("failed to restore config after modeset failure\n");
+ /* Try to restore the config */
+ if (config->mode_changed &&
+ intel_set_mode(save_set.crtc, save_set.mode,
+ save_set.x, save_set.y, save_set.fb))
+ DRM_ERROR("failed to restore config after modeset failure\n");
+ }
out_config:
intel_set_config_free(config);
#define C (((status = I915_READ_NOTRACE(ch_ctl)) & DP_AUX_CH_CTL_SEND_BUSY) == 0)
if (has_aux_irq)
done = wait_event_timeout(dev_priv->gmbus_wait_queue, C,
- msecs_to_jiffies(10));
+ msecs_to_jiffies_timeout(10));
else
done = wait_for_atomic(C, 10) == 0;
if (!done)
* need to wake up periodically and check that ourselves. */
I915_WRITE(GMBUS4 + reg_offset, gmbus4_irq_en);
- for (i = 0; i < msecs_to_jiffies(50) + 1; i++) {
+ for (i = 0; i < msecs_to_jiffies_timeout(50); i++) {
prepare_to_wait(&dev_priv->gmbus_wait_queue, &wait,
TASK_UNINTERRUPTIBLE);
/* Important: The hw handles only the first bit, so set only one! */
I915_WRITE(GMBUS4 + reg_offset, GMBUS_IDLE_EN);
- ret = wait_event_timeout(dev_priv->gmbus_wait_queue, C, 10);
+ ret = wait_event_timeout(dev_priv->gmbus_wait_queue, C,
+ msecs_to_jiffies_timeout(10));
I915_WRITE(GMBUS4 + reg_offset, 0);
},
{
.callback = intel_no_lvds_dmi_callback,
- .ident = "Hewlett-Packard HP t5740e Thin Client",
+ .ident = "Hewlett-Packard HP t5740",
.matches = {
DMI_MATCH(DMI_BOARD_VENDOR, "Hewlett-Packard"),
- DMI_MATCH(DMI_PRODUCT_NAME, "HP t5740e Thin Client"),
+ DMI_MATCH(DMI_PRODUCT_NAME, " t5740"),
},
},
{
* Assume that the preferred modes are
* arranged in priority order.
*/
- intel_ddc_get_modes(connector, intel_sdvo->i2c);
+ intel_ddc_get_modes(connector, &intel_sdvo->ddc);
if (list_empty(&connector->probed_modes) == false)
goto end;
else
hi_pri_lvl = 5;
- WREG8(0x1fde, 0x06);
- WREG8(0x1fdf, hi_pri_lvl);
+ WREG8(MGAREG_CRTCEXT_INDEX, 0x06);
+ WREG8(MGAREG_CRTCEXT_DATA, hi_pri_lvl);
} else {
+ WREG8(MGAREG_CRTCEXT_INDEX, 0x06);
if (mdev->reg_1e24 >= 0x01)
- WREG8(0x1fdf, 0x03);
+ WREG8(MGAREG_CRTCEXT_DATA, 0x03);
else
- WREG8(0x1fdf, 0x04);
+ WREG8(MGAREG_CRTCEXT_DATA, 0x04);
}
}
return 0;
{
const u32 doff = (or * 0x800);
int load = -EINVAL;
+ nv_mask(priv, 0x61a004 + doff, 0x807f0000, 0x80150000);
+ nv_wait(priv, 0x61a004 + doff, 0x80000000, 0x00000000);
nv_wr32(priv, 0x61a00c + doff, 0x00100000 | loadval);
- udelay(9500);
+ mdelay(9);
+ udelay(500);
nv_wr32(priv, 0x61a00c + doff, 0x80000000);
load = (nv_rd32(priv, 0x61a00c + doff) & 0x38000000) >> 27;
nv_wr32(priv, 0x61a00c + doff, 0x00000000);
+ nv_mask(priv, 0x61a004 + doff, 0x807f0000, 0x80550000);
+ nv_wait(priv, 0x61a004 + doff, 0x80000000, 0x00000000);
return load;
}
nv_wr32(priv, 0x616510 + hoff, 0x00000000);
nv_mask(priv, 0x616500 + hoff, 0x00000001, 0x00000001);
+ nv_mask(priv, 0x6165d0 + hoff, 0x00070001, 0x00010001); /* SPARE, HW_CTS */
+ nv_mask(priv, 0x616568 + hoff, 0x00010101, 0x00000000); /* ACR_CTRL, ?? */
+ nv_mask(priv, 0x616578 + hoff, 0x80000000, 0x80000000); /* ACR_0441_ENABLE */
+
/* ??? */
nv_mask(priv, 0x61733c, 0x00100000, 0x00100000); /* RESETF */
nv_mask(priv, 0x61733c, 0x10000000, 0x10000000); /* LOOKUP_EN */
* FIFO channel objects
******************************************************************************/
-void
-nv50_fifo_playlist_update(struct nv50_fifo_priv *priv)
+static void
+nv50_fifo_playlist_update_locked(struct nv50_fifo_priv *priv)
{
struct nouveau_bar *bar = nouveau_bar(priv);
struct nouveau_gpuobj *cur;
int i, p;
- mutex_lock(&nv_subdev(priv)->mutex);
cur = priv->playlist[priv->cur_playlist];
priv->cur_playlist = !priv->cur_playlist;
nv_wr32(priv, 0x0032f4, cur->addr >> 12);
nv_wr32(priv, 0x0032ec, p);
nv_wr32(priv, 0x002500, 0x00000101);
+}
+
+void
+nv50_fifo_playlist_update(struct nv50_fifo_priv *priv)
+{
+ mutex_lock(&nv_subdev(priv)->mutex);
+ nv50_fifo_playlist_update_locked(priv);
mutex_unlock(&nv_subdev(priv)->mutex);
}
for (i = 0; i < 128; i++)
nv_wr32(priv, 0x002600 + (i * 4), 0x00000000);
- nv50_fifo_playlist_update(priv);
+ nv50_fifo_playlist_update_locked(priv);
nv_wr32(priv, 0x003200, 0x00000001);
nv_wr32(priv, 0x003250, 0x00000001);
#define NV50_DISP_DAC_PWR_STATE 0x00000040
#define NV50_DISP_DAC_PWR_STATE_ON 0x00000000
#define NV50_DISP_DAC_PWR_STATE_OFF 0x00000040
-#define NV50_DISP_DAC_LOAD 0x0002000c
+#define NV50_DISP_DAC_LOAD 0x00020100
#define NV50_DISP_DAC_LOAD_VALUE 0x00000007
#define NV50_DISP_PIOR_MTHD 0x00030000
}
s = list_first_entry(&fctx->flip, struct nouveau_page_flip_state, head);
- if (s->event) {
- struct drm_pending_vblank_event *e = s->event;
- struct timeval now;
-
- do_gettimeofday(&now);
- e->event.sequence = 0;
- e->event.tv_sec = now.tv_sec;
- e->event.tv_usec = now.tv_usec;
- list_add_tail(&e->base.link, &e->base.file_priv->event_list);
- wake_up_interruptible(&e->base.file_priv->event_wait);
- }
+ if (s->event)
+ drm_send_vblank_event(dev, -1, s->event);
list_del(&s->head);
if (ps)
{
struct nv50_disp *disp = nv50_disp(encoder->dev);
int ret, or = nouveau_encoder(encoder)->or;
- u32 load = 0;
+ u32 load = nouveau_drm(encoder->dev)->vbios.dactestval;
+ if (load == 0)
+ load = 340;
ret = nv_exec(disp->core, NV50_DISP_DAC_LOAD + or, &load, sizeof(load));
if (ret || load != 7)
static int pdev_probe(struct platform_device *device)
{
+ if (omapdss_is_initialized() == false)
+ return -EPROBE_DEFER;
+
DBG("%s", device->name);
return drm_platform_init(&omap_drm_driver, device);
}
select FB_SYS_FILLRECT
select FB_SYS_COPYAREA
select FB_SYS_IMAGEBLIT
+ select FB_DEFERRED_IO
select DRM_KMS_HELPER
select DRM_TTM
help
struct qxl_bo *cmd_bo;
int release_type;
struct drm_qxl_command *commands =
- (struct drm_qxl_command *)execbuffer->commands;
+ (struct drm_qxl_command *)(uintptr_t)execbuffer->commands;
if (DRM_COPY_FROM_USER(&user_cmd, &commands[cmd_num],
sizeof(user_cmd)))
for (i = 0 ; i < user_cmd.relocs_num; ++i) {
if (DRM_COPY_FROM_USER(&reloc,
- &((struct drm_qxl_reloc *)user_cmd.relocs)[i],
+ &((struct drm_qxl_reloc *)(uintptr_t)user_cmd.relocs)[i],
sizeof(reloc))) {
qxl_bo_list_unreserve(&reloc_list, true);
qxl_release_unreserve(qdev, release);
qdev->vram_mapping = io_mapping_create_wc(qdev->vram_base, pci_resource_len(pdev, 0));
qdev->surface_mapping = io_mapping_create_wc(qdev->surfaceram_base, qdev->surfaceram_size);
- DRM_DEBUG_KMS("qxl: vram %p-%p(%dM %dk), surface %p-%p(%dM %dk)\n",
- (void *)qdev->vram_base, (void *)pci_resource_end(pdev, 0),
+ DRM_DEBUG_KMS("qxl: vram %llx-%llx(%dM %dk), surface %llx-%llx(%dM %dk)\n",
+ (unsigned long long)qdev->vram_base,
+ (unsigned long long)pci_resource_end(pdev, 0),
(int)pci_resource_len(pdev, 0) / 1024 / 1024,
(int)pci_resource_len(pdev, 0) / 1024,
- (void *)qdev->surfaceram_base,
- (void *)pci_resource_end(pdev, 1),
+ (unsigned long long)qdev->surfaceram_base,
+ (unsigned long long)pci_resource_end(pdev, 1),
(int)qdev->surfaceram_size / 1024 / 1024,
(int)qdev->surfaceram_size / 1024);
int
atombios_get_encoder_mode(struct drm_encoder *encoder)
{
+ struct drm_device *dev = encoder->dev;
+ struct radeon_device *rdev = dev->dev_private;
struct radeon_encoder *radeon_encoder = to_radeon_encoder(encoder);
struct drm_connector *connector;
struct radeon_connector *radeon_connector;
case DRM_MODE_CONNECTOR_DVII:
case DRM_MODE_CONNECTOR_HDMIB: /* HDMI-B is basically DL-DVI; analog works fine */
if (drm_detect_hdmi_monitor(radeon_connector->edid) &&
- radeon_audio)
+ radeon_audio &&
+ !ASIC_IS_DCE6(rdev)) /* remove once we support DCE6 */
return ATOM_ENCODER_MODE_HDMI;
else if (radeon_connector->use_digital)
return ATOM_ENCODER_MODE_DVI;
case DRM_MODE_CONNECTOR_HDMIA:
default:
if (drm_detect_hdmi_monitor(radeon_connector->edid) &&
- radeon_audio)
+ radeon_audio &&
+ !ASIC_IS_DCE6(rdev)) /* remove once we support DCE6 */
return ATOM_ENCODER_MODE_HDMI;
else
return ATOM_ENCODER_MODE_DVI;
(dig_connector->dp_sink_type == CONNECTOR_OBJECT_ID_eDP))
return ATOM_ENCODER_MODE_DP;
else if (drm_detect_hdmi_monitor(radeon_connector->edid) &&
- radeon_audio)
+ radeon_audio &&
+ !ASIC_IS_DCE6(rdev)) /* remove once we support DCE6 */
return ATOM_ENCODER_MODE_HDMI;
else
return ATOM_ENCODER_MODE_DVI;
rdev->ring[R600_RING_TYPE_UVD_INDEX].ring_size = 0;
/* Enable IRQ */
+ if (!rdev->irq.installed) {
+ r = radeon_irq_kms_init(rdev);
+ if (r)
+ return r;
+ }
+
r = r600_irq_init(rdev);
if (r) {
DRM_ERROR("radeon: IH init failed (%d).\n", r);
if (r)
return r;
- r = radeon_irq_kms_init(rdev);
- if (r)
- return r;
-
rdev->ring[RADEON_RING_TYPE_GFX_INDEX].ring_obj = NULL;
r600_ring_init(rdev, &rdev->ring[RADEON_RING_TYPE_GFX_INDEX], 1024 * 1024);
void evergreen_pcie_gen2_enable(struct radeon_device *rdev)
{
- u32 link_width_cntl, speed_cntl, mask;
- int ret;
+ u32 link_width_cntl, speed_cntl;
if (radeon_pcie_gen2 == 0)
return;
if (ASIC_IS_X2(rdev))
return;
- ret = drm_pcie_get_speed_cap_mask(rdev->ddev, &mask);
- if (ret != 0)
- return;
-
- if (!(mask & DRM_PCIE_SPEED_50))
+ if ((rdev->pdev->bus->max_bus_speed != PCIE_SPEED_5_0GT) &&
+ (rdev->pdev->bus->max_bus_speed != PCIE_SPEED_8_0GT))
return;
speed_cntl = RREG32_PCIE_PORT(PCIE_LC_SPEED_CNTL);
}
/* Enable IRQ */
+ if (!rdev->irq.installed) {
+ r = radeon_irq_kms_init(rdev);
+ if (r)
+ return r;
+ }
+
r = r600_irq_init(rdev);
if (r) {
DRM_ERROR("radeon: IH init failed (%d).\n", r);
if (r)
return r;
- r = radeon_irq_kms_init(rdev);
- if (r)
- return r;
-
ring->ring_obj = NULL;
r600_ring_init(rdev, ring, 1024 * 1024);
}
/* Enable IRQ */
+ if (!rdev->irq.installed) {
+ r = radeon_irq_kms_init(rdev);
+ if (r)
+ return r;
+ }
+
r100_irq_set(rdev);
rdev->config.r100.hdp_cntl = RREG32(RADEON_HOST_PATH_CNTL);
/* 1M ring buffer */
r100_mc_init(rdev);
/* Fence driver */
r = radeon_fence_driver_init(rdev);
- if (r)
- return r;
- r = radeon_irq_kms_init(rdev);
if (r)
return r;
/* Memory manager */
}
/* Enable IRQ */
+ if (!rdev->irq.installed) {
+ r = radeon_irq_kms_init(rdev);
+ if (r)
+ return r;
+ }
+
r100_irq_set(rdev);
rdev->config.r300.hdp_cntl = RREG32(RADEON_HOST_PATH_CNTL);
/* 1M ring buffer */
r300_mc_init(rdev);
/* Fence driver */
r = radeon_fence_driver_init(rdev);
- if (r)
- return r;
- r = radeon_irq_kms_init(rdev);
if (r)
return r;
/* Memory manager */
}
/* Enable IRQ */
+ if (!rdev->irq.installed) {
+ r = radeon_irq_kms_init(rdev);
+ if (r)
+ return r;
+ }
+
r100_irq_set(rdev);
rdev->config.r300.hdp_cntl = RREG32(RADEON_HOST_PATH_CNTL);
/* 1M ring buffer */
if (r) {
return r;
}
- r = radeon_irq_kms_init(rdev);
- if (r) {
- return r;
- }
/* Memory manager */
r = radeon_bo_init(rdev);
if (r) {
}
/* Enable IRQ */
+ if (!rdev->irq.installed) {
+ r = radeon_irq_kms_init(rdev);
+ if (r)
+ return r;
+ }
+
rs600_irq_set(rdev);
rdev->config.r300.hdp_cntl = RREG32(RADEON_HOST_PATH_CNTL);
/* 1M ring buffer */
rv515_debugfs(rdev);
/* Fence driver */
r = radeon_fence_driver_init(rdev);
- if (r)
- return r;
- r = radeon_irq_kms_init(rdev);
if (r)
return r;
/* Memory manager */
return -1;
}
+uint32_t rs780_mc_rreg(struct radeon_device *rdev, uint32_t reg)
+{
+ uint32_t r;
+
+ WREG32(R_0028F8_MC_INDEX, S_0028F8_MC_IND_ADDR(reg));
+ r = RREG32(R_0028FC_MC_DATA);
+ WREG32(R_0028F8_MC_INDEX, ~C_0028F8_MC_IND_ADDR);
+ return r;
+}
+
+void rs780_mc_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v)
+{
+ WREG32(R_0028F8_MC_INDEX, S_0028F8_MC_IND_ADDR(reg) |
+ S_0028F8_MC_IND_WR_EN(1));
+ WREG32(R_0028FC_MC_DATA, v);
+ WREG32(R_0028F8_MC_INDEX, 0x7F);
+}
+
static void r600_mc_program(struct radeon_device *rdev)
{
struct rv515_mc_save save;
{
u32 tmp;
int chansize, numchan;
+ uint32_t h_addr, l_addr;
+ unsigned long long k8_addr;
/* Get VRAM informations */
rdev->mc.vram_is_ddr = true;
if (rdev->flags & RADEON_IS_IGP) {
rs690_pm_info(rdev);
rdev->mc.igp_sideport_enabled = radeon_atombios_sideport_present(rdev);
+
+ if (rdev->family == CHIP_RS780 || rdev->family == CHIP_RS880) {
+ /* Use K8 direct mapping for fast fb access. */
+ rdev->fastfb_working = false;
+ h_addr = G_000012_K8_ADDR_EXT(RREG32_MC(R_000012_MC_MISC_UMA_CNTL));
+ l_addr = RREG32_MC(R_000011_K8_FB_LOCATION);
+ k8_addr = ((unsigned long long)h_addr) << 32 | l_addr;
+#if defined(CONFIG_X86_32) && !defined(CONFIG_X86_PAE)
+ if (k8_addr + rdev->mc.visible_vram_size < 0x100000000ULL)
+#endif
+ {
+ /* FastFB shall be used with UMA memory. Here it is simply disabled when sideport
+ * memory is present.
+ */
+ if (rdev->mc.igp_sideport_enabled == false && radeon_fastfb == 1) {
+ DRM_INFO("Direct mapping: aper base at 0x%llx, replaced by direct mapping base 0x%llx.\n",
+ (unsigned long long)rdev->mc.aper_base, k8_addr);
+ rdev->mc.aper_base = (resource_size_t)k8_addr;
+ rdev->fastfb_working = true;
+ }
+ }
+ }
}
+
radeon_update_bandwidth_info(rdev);
return 0;
}
}
/* Enable IRQ */
+ if (!rdev->irq.installed) {
+ r = radeon_irq_kms_init(rdev);
+ if (r)
+ return r;
+ }
+
r = r600_irq_init(rdev);
if (r) {
DRM_ERROR("radeon: IH init failed (%d).\n", r);
if (r)
return r;
- r = radeon_irq_kms_init(rdev);
- if (r)
- return r;
-
rdev->ring[RADEON_RING_TYPE_GFX_INDEX].ring_obj = NULL;
r600_ring_init(rdev, &rdev->ring[RADEON_RING_TYPE_GFX_INDEX], 1024 * 1024);
{
u32 link_width_cntl, lanes, speed_cntl, training_cntl, tmp;
u16 link_cntl2;
- u32 mask;
- int ret;
if (radeon_pcie_gen2 == 0)
return;
if (rdev->family <= CHIP_R600)
return;
- ret = drm_pcie_get_speed_cap_mask(rdev->ddev, &mask);
- if (ret != 0)
- return;
-
- if (!(mask & DRM_PCIE_SPEED_50))
+ if ((rdev->pdev->bus->max_bus_speed != PCIE_SPEED_5_0GT) &&
+ (rdev->pdev->bus->max_bus_speed != PCIE_SPEED_8_0GT))
return;
speed_cntl = RREG32_PCIE_PORT(PCIE_LC_SPEED_CNTL);
#define PACKET3_STRMOUT_BASE_UPDATE 0x72 /* r7xx */
#define PACKET3_SURFACE_BASE_UPDATE 0x73
+#define R_000011_K8_FB_LOCATION 0x11
+#define R_000012_MC_MISC_UMA_CNTL 0x12
+#define G_000012_K8_ADDR_EXT(x) (((x) >> 0) & 0xFF)
+#define R_0028F8_MC_INDEX 0x28F8
+#define S_0028F8_MC_IND_ADDR(x) (((x) & 0x1FF) << 0)
+#define C_0028F8_MC_IND_ADDR 0xFFFFFE00
+#define S_0028F8_MC_IND_WR_EN(x) (((x) & 0x1) << 9)
+#define R_0028FC_MC_DATA 0x28FC
#define R_008020_GRBM_SOFT_RESET 0x8020
#define S_008020_SOFT_RESET_CP(x) (((x) & 1) << 0)
rdev->mc_rreg = &rs600_mc_rreg;
rdev->mc_wreg = &rs600_mc_wreg;
}
+ if (rdev->family == CHIP_RS780 || rdev->family == CHIP_RS880) {
+ rdev->mc_rreg = &rs780_mc_rreg;
+ rdev->mc_wreg = &rs780_mc_wreg;
+ }
if (rdev->family >= CHIP_R600) {
rdev->pciep_rreg = &r600_pciep_rreg;
rdev->pciep_wreg = &r600_pciep_wreg;
extern void r600_pm_misc(struct radeon_device *rdev);
extern void r600_pm_init_profile(struct radeon_device *rdev);
extern void rs780_pm_init_profile(struct radeon_device *rdev);
+extern uint32_t rs780_mc_rreg(struct radeon_device *rdev, uint32_t reg);
+extern void rs780_mc_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v);
extern void r600_pm_get_dynpm_state(struct radeon_device *rdev);
extern void r600_set_pcie_lanes(struct radeon_device *rdev, int lanes);
extern int r600_get_pcie_lanes(struct radeon_device *rdev);
{
uint32_t reg;
+ /* required for EFI mode on macbook2,1 which uses an r5xx asic */
if (efi_enabled(EFI_BOOT) &&
- rdev->pdev->subsystem_vendor == PCI_VENDOR_ID_APPLE)
+ (rdev->pdev->subsystem_vendor == PCI_VENDOR_ID_APPLE) &&
+ (rdev->family < CHIP_R600))
return false;
+ if (ASIC_IS_NODCE(rdev))
+ goto check_memsize;
+
/* first check CRTCs */
- if (ASIC_IS_DCE41(rdev)) {
+ if (ASIC_IS_DCE4(rdev)) {
reg = RREG32(EVERGREEN_CRTC_CONTROL + EVERGREEN_CRTC0_REGISTER_OFFSET) |
RREG32(EVERGREEN_CRTC_CONTROL + EVERGREEN_CRTC1_REGISTER_OFFSET);
- if (reg & EVERGREEN_CRTC_MASTER_EN)
- return true;
- } else if (ASIC_IS_DCE4(rdev)) {
- reg = RREG32(EVERGREEN_CRTC_CONTROL + EVERGREEN_CRTC0_REGISTER_OFFSET) |
- RREG32(EVERGREEN_CRTC_CONTROL + EVERGREEN_CRTC1_REGISTER_OFFSET) |
- RREG32(EVERGREEN_CRTC_CONTROL + EVERGREEN_CRTC2_REGISTER_OFFSET) |
- RREG32(EVERGREEN_CRTC_CONTROL + EVERGREEN_CRTC3_REGISTER_OFFSET) |
- RREG32(EVERGREEN_CRTC_CONTROL + EVERGREEN_CRTC4_REGISTER_OFFSET) |
- RREG32(EVERGREEN_CRTC_CONTROL + EVERGREEN_CRTC5_REGISTER_OFFSET);
+ if (rdev->num_crtc >= 4) {
+ reg |= RREG32(EVERGREEN_CRTC_CONTROL + EVERGREEN_CRTC2_REGISTER_OFFSET) |
+ RREG32(EVERGREEN_CRTC_CONTROL + EVERGREEN_CRTC3_REGISTER_OFFSET);
+ }
+ if (rdev->num_crtc >= 6) {
+ reg |= RREG32(EVERGREEN_CRTC_CONTROL + EVERGREEN_CRTC4_REGISTER_OFFSET) |
+ RREG32(EVERGREEN_CRTC_CONTROL + EVERGREEN_CRTC5_REGISTER_OFFSET);
+ }
if (reg & EVERGREEN_CRTC_MASTER_EN)
return true;
} else if (ASIC_IS_AVIVO(rdev)) {
}
}
+check_memsize:
/* then check MEM_SIZE, in case the crtcs are off */
if (rdev->family >= CHIP_R600)
reg = RREG32(R600_CONFIG_MEMSIZE);
{
struct radeon_crtc *radeon_crtc = rdev->mode_info.crtcs[crtc_id];
struct radeon_unpin_work *work;
- struct drm_pending_vblank_event *e;
- struct timeval now;
unsigned long flags;
u32 update_pending;
int vpos, hpos;
radeon_crtc->unpin_work = NULL;
/* wakeup userspace */
- if (work->event) {
- e = work->event;
- e->event.sequence = drm_vblank_count_and_time(rdev->ddev, crtc_id, &now);
- e->event.tv_sec = now.tv_sec;
- e->event.tv_usec = now.tv_usec;
- list_add_tail(&e->base.link, &e->base.file_priv->event_list);
- wake_up_interruptible(&e->base.file_priv->event_wait);
- }
+ if (work->event)
+ drm_send_vblank_event(rdev->ddev, crtc_id, work->event);
+
spin_unlock_irqrestore(&rdev->ddev->event_lock, flags);
drm_vblank_put(rdev->ddev, radeon_crtc->crtc_id);
}
/* Enable IRQ */
+ if (!rdev->irq.installed) {
+ r = radeon_irq_kms_init(rdev);
+ if (r)
+ return r;
+ }
+
r100_irq_set(rdev);
rdev->config.r300.hdp_cntl = RREG32(RADEON_HOST_PATH_CNTL);
/* 1M ring buffer */
rs400_mc_init(rdev);
/* Fence driver */
r = radeon_fence_driver_init(rdev);
- if (r)
- return r;
- r = radeon_irq_kms_init(rdev);
if (r)
return r;
/* Memory manager */
}
/* Enable IRQ */
+ if (!rdev->irq.installed) {
+ r = radeon_irq_kms_init(rdev);
+ if (r)
+ return r;
+ }
+
rs600_irq_set(rdev);
rdev->config.r300.hdp_cntl = RREG32(RADEON_HOST_PATH_CNTL);
/* 1M ring buffer */
rs600_debugfs(rdev);
/* Fence driver */
r = radeon_fence_driver_init(rdev);
- if (r)
- return r;
- r = radeon_irq_kms_init(rdev);
if (r)
return r;
/* Memory manager */
}
/* Enable IRQ */
+ if (!rdev->irq.installed) {
+ r = radeon_irq_kms_init(rdev);
+ if (r)
+ return r;
+ }
+
rs600_irq_set(rdev);
rdev->config.r300.hdp_cntl = RREG32(RADEON_HOST_PATH_CNTL);
/* 1M ring buffer */
rv515_debugfs(rdev);
/* Fence driver */
r = radeon_fence_driver_init(rdev);
- if (r)
- return r;
- r = radeon_irq_kms_init(rdev);
if (r)
return r;
/* Memory manager */
}
/* Enable IRQ */
+ if (!rdev->irq.installed) {
+ r = radeon_irq_kms_init(rdev);
+ if (r)
+ return r;
+ }
+
rs600_irq_set(rdev);
rdev->config.r300.hdp_cntl = RREG32(RADEON_HOST_PATH_CNTL);
/* 1M ring buffer */
rv515_debugfs(rdev);
/* Fence driver */
r = radeon_fence_driver_init(rdev);
- if (r)
- return r;
- r = radeon_irq_kms_init(rdev);
if (r)
return r;
/* Memory manager */
chip_id = 0x0100000b;
break;
case CHIP_SUMO:
- chip_id = 0x0100000c;
- break;
case CHIP_SUMO2:
- chip_id = 0x0100000d;
+ chip_id = 0x0100000c;
break;
case CHIP_PALM:
chip_id = 0x0100000e;
rdev->ring[R600_RING_TYPE_UVD_INDEX].ring_size = 0;
/* Enable IRQ */
+ if (!rdev->irq.installed) {
+ r = radeon_irq_kms_init(rdev);
+ if (r)
+ return r;
+ }
+
r = r600_irq_init(rdev);
if (r) {
DRM_ERROR("radeon: IH init failed (%d).\n", r);
if (r)
return r;
- r = radeon_irq_kms_init(rdev);
- if (r)
- return r;
-
rdev->ring[RADEON_RING_TYPE_GFX_INDEX].ring_obj = NULL;
r600_ring_init(rdev, &rdev->ring[RADEON_RING_TYPE_GFX_INDEX], 1024 * 1024);
{
u32 link_width_cntl, lanes, speed_cntl, tmp;
u16 link_cntl2;
- u32 mask;
- int ret;
if (radeon_pcie_gen2 == 0)
return;
if (ASIC_IS_X2(rdev))
return;
- ret = drm_pcie_get_speed_cap_mask(rdev->ddev, &mask);
- if (ret != 0)
- return;
-
- if (!(mask & DRM_PCIE_SPEED_50))
+ if ((rdev->pdev->bus->max_bus_speed != PCIE_SPEED_5_0GT) &&
+ (rdev->pdev->bus->max_bus_speed != PCIE_SPEED_8_0GT))
return;
DRM_INFO("enabling PCIE gen 2 link speeds, disable with radeon.pcie_gen2=0\n");
default:
rdev->config.si.max_shader_engines = 1;
rdev->config.si.max_tile_pipes = 4;
- rdev->config.si.max_cu_per_sh = 2;
+ rdev->config.si.max_cu_per_sh = 5;
rdev->config.si.max_sh_per_se = 2;
rdev->config.si.max_backends_per_se = 4;
rdev->config.si.max_texture_channel_caches = 4;
}
/* Enable IRQ */
+ if (!rdev->irq.installed) {
+ r = radeon_irq_kms_init(rdev);
+ if (r)
+ return r;
+ }
+
r = si_irq_init(rdev);
if (r) {
DRM_ERROR("radeon: IH init failed (%d).\n", r);
if (r)
return r;
- r = radeon_irq_kms_init(rdev);
- if (r)
- return r;
-
ring = &rdev->ring[RADEON_RING_TYPE_GFX_INDEX];
ring->ring_obj = NULL;
r600_ring_init(rdev, ring, 1024 * 1024);
{
struct drm_pending_vblank_event *event;
struct drm_device *dev = scrtc->crtc.dev;
- struct timeval vblanktime;
unsigned long flags;
spin_lock_irqsave(&dev->event_lock, flags);
event = scrtc->event;
scrtc->event = NULL;
+ if (event) {
+ drm_send_vblank_event(dev, 0, event);
+ drm_vblank_put(dev, 0);
+ }
spin_unlock_irqrestore(&dev->event_lock, flags);
-
- if (event == NULL)
- return;
-
- event->event.sequence = drm_vblank_count_and_time(dev, 0, &vblanktime);
- event->event.tv_sec = vblanktime.tv_sec;
- event->event.tv_usec = vblanktime.tv_usec;
-
- spin_lock_irqsave(&dev->event_lock, flags);
- list_add_tail(&event->base.link, &event->base.file_priv->event_list);
- wake_up_interruptible(&event->base.file_priv->event_wait);
- spin_unlock_irqrestore(&dev->event_lock, flags);
-
- drm_vblank_put(dev, 0);
}
static int shmob_drm_crtc_page_flip(struct drm_crtc *crtc,
select DRM_GEM_CMA_HELPER
select VIDEOMODE_HELPERS
select BACKLIGHT_CLASS_DEVICE
+ select BACKLIGHT_LCD_SUPPORT
help
Choose this option if you have an TI SoC with LCDC display
controller, for example AM33xx in beagle-bone, DA8xx, or
return 0;
}
cur_cpu = (++next_vp % max_cpus);
- return cur_cpu;
+ return hv_context.vp_index[cur_cpu];
}
/*
#ifdef CONFIG_PM_SLEEP
static int exynos_adc_suspend(struct device *dev)
{
- struct platform_device *pdev = to_platform_device(dev);
- struct exynos_adc *info = platform_get_drvdata(pdev);
+ struct iio_dev *indio_dev = dev_get_drvdata(dev);
+ struct exynos_adc *info = iio_priv(indio_dev);
u32 con;
if (info->version == ADC_V2) {
static int exynos_adc_resume(struct device *dev)
{
- struct platform_device *pdev = to_platform_device(dev);
- struct exynos_adc *info = platform_get_drvdata(pdev);
+ struct iio_dev *indio_dev = dev_get_drvdata(dev);
+ struct exynos_adc *info = iio_priv(indio_dev);
int ret;
ret = regulator_enable(info->vdd);
while (chan->indio_dev) {
if (chan->indio_dev != indio_dev) {
ret = -EINVAL;
- goto error_release_channels;
+ goto error_free_scan_mask;
}
set_bit(chan->channel->scan_index,
cb_buff->buffer.scan_mask);
return cb_buff;
+error_free_scan_mask:
+ kfree(cb_buff->buffer.scan_mask);
error_release_channels:
iio_channel_release_all(cb_buff->channels);
error_free_cb_buff:
void iio_channel_release_all_cb(struct iio_cb_buffer *cb_buff)
{
+ kfree(cb_buff->buffer.scan_mask);
iio_channel_release_all(cb_buff->channels);
kfree(cb_buff);
}
goto read_error;
*val = *val >> ch->scan_type.shift;
+
+ err = st_sensors_set_enable(indio_dev, false);
}
mutex_unlock(&indio_dev->mlock);
config AD5064
tristate "Analog Devices AD5064 and similar multi-channel DAC driver"
- depends on (SPI_MASTER || I2C)
+ depends on (SPI_MASTER && I2C!=m) || I2C
help
Say yes here to build support for Analog Devices AD5024, AD5025, AD5044,
AD5045, AD5064, AD5064-1, AD5065, AD5628, AD5629R, AD5648, AD5666, AD5668,
config AD5380
tristate "Analog Devices AD5380/81/82/83/84/90/91/92 DAC driver"
- depends on (SPI_MASTER || I2C)
+ depends on (SPI_MASTER && I2C!=m) || I2C
select REGMAP_I2C if I2C
select REGMAP_SPI if SPI_MASTER
help
config AD5446
tristate "Analog Devices AD5446 and similar single channel DACs driver"
- depends on (SPI_MASTER || I2C)
+ depends on (SPI_MASTER && I2C!=m) || I2C
help
Say yes here to build support for Analog Devices AD5300, AD5301, AD5310,
AD5311, AD5320, AD5321, AD5444, AD5446, AD5450, AD5451, AD5452, AD5453,
(pdata->r2_user_settings & (ADF4350_REG2_PD_POLARITY_POS |
ADF4350_REG2_LDP_6ns | ADF4350_REG2_LDF_INT_N |
ADF4350_REG2_CHARGE_PUMP_CURR_uA(5000) |
- ADF4350_REG2_MUXOUT(0x7) | ADF4350_REG2_NOISE_MODE(0x9)));
+ ADF4350_REG2_MUXOUT(0x7) | ADF4350_REG2_NOISE_MODE(0x3)));
st->regs[ADF4350_REG3] = pdata->r3_user_settings &
(ADF4350_REG3_12BIT_CLKDIV(0xFFF) |
channel->indio_dev = indio_dev;
index = iiospec.args_count ? iiospec.args[0] : 0;
if (index >= indio_dev->num_channels) {
- return -EINVAL;
+ err = -EINVAL;
goto err_put;
}
channel->channel = &indio_dev->channels[index];
s64 raw64 = raw;
int ret;
- ret = iio_channel_read(chan, &offset, NULL, IIO_CHAN_INFO_SCALE);
+ ret = iio_channel_read(chan, &offset, NULL, IIO_CHAN_INFO_OFFSET);
if (ret == 0)
raw64 += offset;
if (dma_region) {
struct qib_mregion *tmr;
- tmr = rcu_dereference(dev->dma_mr);
+ tmr = rcu_access_pointer(dev->dma_mr);
if (!tmr) {
qib_get_mr(mr);
rcu_assign_pointer(dev->dma_mr, mr);
* Copyright (C) 2004 Alex Aizman
* Copyright (C) 2005 Mike Christie
* Copyright (c) 2005, 2006 Voltaire, Inc. All rights reserved.
+ * Copyright (c) 2013 Mellanox Technologies. All rights reserved.
* maintained by openib-general@openib.org
*
* This software is available to you under a choice of one of two
*
* Copyright (c) 2004, 2005, 2006 Voltaire, Inc. All rights reserved.
* Copyright (c) 2005, 2006 Cisco Systems. All rights reserved.
+ * Copyright (c) 2013 Mellanox Technologies. All rights reserved.
*
* This software is available to you under a choice of one of two
* licenses. You may choose to be licensed under the terms of the GNU
/*
* Copyright (c) 2004, 2005, 2006 Voltaire, Inc. All rights reserved.
+ * Copyright (c) 2013 Mellanox Technologies. All rights reserved.
*
* This software is available to you under a choice of one of two
* licenses. You may choose to be licensed under the terms of the GNU
/*
* Copyright (c) 2004, 2005, 2006 Voltaire, Inc. All rights reserved.
+ * Copyright (c) 2013 Mellanox Technologies. All rights reserved.
*
* This software is available to you under a choice of one of two
* licenses. You may choose to be licensed under the terms of the GNU
/*
* Copyright (c) 2004, 2005, 2006 Voltaire, Inc. All rights reserved.
* Copyright (c) 2005, 2006 Cisco Systems. All rights reserved.
+ * Copyright (c) 2013 Mellanox Technologies. All rights reserved.
*
* This software is available to you under a choice of one of two
* licenses. You may choose to be licensed under the terms of the GNU
}
/**
- * releases the FMR pool, QP and CMA ID objects, returns 0 on success,
+ * releases the FMR pool and QP objects, returns 0 on success,
* -1 on failure
*/
-static int iser_free_ib_conn_res(struct iser_conn *ib_conn, int can_destroy_id)
+static int iser_free_ib_conn_res(struct iser_conn *ib_conn)
{
int cq_index;
BUG_ON(ib_conn == NULL);
rdma_destroy_qp(ib_conn->cma_id);
}
- /* if cma handler context, the caller acts s.t the cma destroy the id */
- if (ib_conn->cma_id != NULL && can_destroy_id)
- rdma_destroy_id(ib_conn->cma_id);
ib_conn->fmr_pool = NULL;
ib_conn->qp = NULL;
- ib_conn->cma_id = NULL;
kfree(ib_conn->page_vec);
if (ib_conn->login_buf) {
list_del(&ib_conn->conn_list);
mutex_unlock(&ig.connlist_mutex);
iser_free_rx_descriptors(ib_conn);
- iser_free_ib_conn_res(ib_conn, can_destroy_id);
+ iser_free_ib_conn_res(ib_conn);
ib_conn->device = NULL;
/* on EVENT_ADDR_ERROR there's no device yet for this conn */
if (device != NULL)
iser_device_try_release(device);
+ /* if cma handler context, the caller actually destroy the id */
+ if (ib_conn->cma_id != NULL && can_destroy_id) {
+ rdma_destroy_id(ib_conn->cma_id);
+ ib_conn->cma_id = NULL;
+ }
iscsi_destroy_endpoint(ib_conn->ep);
}
spin_unlock_irq(&sdev->spinlock);
}
+/**
+ * srpt_shutdown_session() - Whether or not a session may be shut down.
+ */
+static int srpt_shutdown_session(struct se_session *se_sess)
+{
+ struct srpt_rdma_ch *ch = se_sess->fabric_sess_ptr;
+ unsigned long flags;
+
+ spin_lock_irqsave(&ch->spinlock, flags);
+ if (ch->in_shutdown) {
+ spin_unlock_irqrestore(&ch->spinlock, flags);
+ return true;
+ }
+
+ ch->in_shutdown = true;
+ target_sess_cmd_list_set_waiting(se_sess);
+ spin_unlock_irqrestore(&ch->spinlock, flags);
+
+ return true;
+}
+
/**
* srpt_drain_channel() - Drain a channel by resetting the IB queue pair.
* @cm_id: Pointer to the CM ID of the channel to be drained.
spin_unlock_irq(&sdev->spinlock);
if (do_reset) {
+ if (ch->sess)
+ srpt_shutdown_session(ch->sess);
+
ret = srpt_ch_qp_err(ch);
if (ret < 0)
printk(KERN_ERR "Setting queue pair in error state"
se_sess = ch->sess;
BUG_ON(!se_sess);
- target_wait_for_sess_cmds(se_sess, 0);
+ target_wait_for_sess_cmds(se_sess);
transport_deregister_session_configfs(se_sess);
transport_deregister_session(se_sess);
spin_unlock_irqrestore(&ch->spinlock, flags);
}
-/**
- * srpt_shutdown_session() - Whether or not a session may be shut down.
- */
-static int srpt_shutdown_session(struct se_session *se_sess)
-{
- return true;
-}
-
/**
* srpt_close_session() - Forcibly close a session.
*
u8 sess_name[36];
struct work_struct release_work;
struct completion *release_done;
+ bool in_shutdown;
};
/**
{
struct synaptics_data *priv = psmouse->private;
struct synaptics_data old_priv = *priv;
+ unsigned char param[2];
int retry = 0;
int error;
*/
ssleep(1);
}
+ ps2_command(&psmouse->ps2dev, param, PSMOUSE_CMD_GETID);
error = synaptics_detect(psmouse, 0);
} while (error && ++retry < 3);
wacom->id[idx] = (data[2] << 4) | (data[3] >> 4) |
((data[7] & 0x0f) << 20) | ((data[8] & 0xf0) << 12);
- switch (wacom->id[idx] & 0xfffff) {
+ switch (wacom->id[idx]) {
case 0x812: /* Inking pen */
case 0x801: /* Intuos3 Inking pen */
- case 0x20802: /* Intuos4 Inking Pen */
+ case 0x120802: /* Intuos4/5 Inking Pen */
case 0x012:
wacom->tool[idx] = BTN_TOOL_PENCIL;
break;
case 0x823: /* Intuos3 Grip Pen */
case 0x813: /* Intuos3 Classic Pen */
case 0x885: /* Intuos3 Marker Pen */
- case 0x802: /* Intuos4 General Pen */
- case 0x804: /* Intuos4 Marker Pen */
- case 0x40802: /* Intuos4 Classic Pen */
- case 0x18802: /* DTH2242 Grip Pen */
+ case 0x802: /* Intuos4/5 13HD/24HD General Pen */
+ case 0x804: /* Intuos4/5 13HD/24HD Marker Pen */
case 0x022:
+ case 0x100804: /* Intuos4/5 13HD/24HD Art Pen */
+ case 0x140802: /* Intuos4/5 13HD/24HD Classic Pen */
+ case 0x160802: /* Cintiq 13HD Pro Pen */
+ case 0x180802: /* DTH2242 Pen */
wacom->tool[idx] = BTN_TOOL_PEN;
break;
case 0x82b: /* Intuos3 Grip Pen Eraser */
case 0x81b: /* Intuos3 Classic Pen Eraser */
case 0x91b: /* Intuos3 Airbrush Eraser */
- case 0x80c: /* Intuos4 Marker Pen Eraser */
- case 0x80a: /* Intuos4 General Pen Eraser */
- case 0x4080a: /* Intuos4 Classic Pen Eraser */
- case 0x90a: /* Intuos4 Airbrush Eraser */
+ case 0x80c: /* Intuos4/5 13HD/24HD Marker Pen Eraser */
+ case 0x80a: /* Intuos4/5 13HD/24HD General Pen Eraser */
+ case 0x90a: /* Intuos4/5 13HD/24HD Airbrush Eraser */
+ case 0x14080a: /* Intuos4/5 13HD/24HD Classic Pen Eraser */
+ case 0x10090a: /* Intuos4/5 13HD/24HD Airbrush Eraser */
+ case 0x10080c: /* Intuos4/5 13HD/24HD Art Pen Eraser */
+ case 0x16080a: /* Cintiq 13HD Pro Pen Eraser */
+ case 0x18080a: /* DTH2242 Eraser */
wacom->tool[idx] = BTN_TOOL_RUBBER;
break;
case 0x912:
case 0x112:
case 0x913: /* Intuos3 Airbrush */
- case 0x902: /* Intuos4 Airbrush */
+ case 0x902: /* Intuos4/5 13HD/24HD Airbrush */
+ case 0x100902: /* Intuos4/5 13HD/24HD Airbrush */
wacom->tool[idx] = BTN_TOOL_AIRBRUSH;
break;
input_report_key(input, BTN_8, (data[3] & 0x80));
}
if (data[1] | (data[2] & 0x01) | data[3]) {
- input_report_key(input, wacom->tool[1], 1);
input_report_abs(input, ABS_MISC, PAD_DEVICE_ID);
} else {
- input_report_key(input, wacom->tool[1], 0);
input_report_abs(input, ABS_MISC, 0);
}
} else if (features->type == DTK) {
input_report_key(input, BTN_3, (data[6] & 0x08));
input_report_key(input, BTN_4, (data[6] & 0x10));
input_report_key(input, BTN_5, (data[6] & 0x20));
+ if (data[6] & 0x3f) {
+ input_report_abs(input, ABS_MISC, PAD_DEVICE_ID);
+ } else {
+ input_report_abs(input, ABS_MISC, 0);
+ }
+ } else if (features->type == WACOM_13HD) {
+ input_report_key(input, BTN_0, (data[3] & 0x01));
+ input_report_key(input, BTN_1, (data[4] & 0x01));
+ input_report_key(input, BTN_2, (data[4] & 0x02));
+ input_report_key(input, BTN_3, (data[4] & 0x04));
+ input_report_key(input, BTN_4, (data[4] & 0x08));
+ input_report_key(input, BTN_5, (data[4] & 0x10));
+ input_report_key(input, BTN_6, (data[4] & 0x20));
+ input_report_key(input, BTN_7, (data[4] & 0x40));
+ input_report_key(input, BTN_8, (data[4] & 0x80));
+ if ((data[3] & 0x01) | data[4]) {
+ input_report_abs(input, ABS_MISC, PAD_DEVICE_ID);
+ } else {
+ input_report_abs(input, ABS_MISC, 0);
+ }
} else if (features->type == WACOM_24HD) {
input_report_key(input, BTN_0, (data[6] & 0x01));
input_report_key(input, BTN_1, (data[6] & 0x02));
}
if (data[1] | data[2] | (data[3] & 0x1f) | data[4] | data[6] | data[8]) {
- input_report_key(input, wacom->tool[1], 1);
input_report_abs(input, ABS_MISC, PAD_DEVICE_ID);
} else {
- input_report_key(input, wacom->tool[1], 0);
input_report_abs(input, ABS_MISC, 0);
}
} else if (features->type >= INTUOS5S && features->type <= INTUOS5L) {
}
if (data[2] | (data[3] & 0x01) | data[4] | data[5]) {
- input_report_key(input, wacom->tool[1], 1);
input_report_abs(input, ABS_MISC, PAD_DEVICE_ID);
} else {
- input_report_key(input, wacom->tool[1], 0);
input_report_abs(input, ABS_MISC, 0);
}
} else {
if ((data[5] & 0x1f) | data[6] | (data[1] & 0x1f) |
data[2] | (data[3] & 0x1f) | data[4] | data[8] |
(data[7] & 0x01)) {
- input_report_key(input, wacom->tool[1], 1);
input_report_abs(input, ABS_MISC, PAD_DEVICE_ID);
} else {
- input_report_key(input, wacom->tool[1], 0);
input_report_abs(input, ABS_MISC, 0);
}
}
case INTUOS4L:
case CINTIQ:
case WACOM_BEE:
+ case WACOM_13HD:
case WACOM_21UX2:
case WACOM_22HD:
case WACOM_24HD:
__set_bit(KEY_PROG1, input_dev->keybit);
__set_bit(KEY_PROG2, input_dev->keybit);
__set_bit(KEY_PROG3, input_dev->keybit);
+
+ input_set_abs_params(input_dev, ABS_Z, -900, 899, 0, 0);
+ input_set_abs_params(input_dev, ABS_THROTTLE, 0, 71, 0, 0);
/* fall through */
case DTK:
for (i = 0; i < 6; i++)
__set_bit(BTN_0 + i, input_dev->keybit);
- input_set_abs_params(input_dev, ABS_Z, -900, 899, 0, 0);
- input_set_abs_params(input_dev, ABS_THROTTLE, 0, 71, 0, 0);
-
__set_bit(INPUT_PROP_DIRECT, input_dev->propbit);
wacom_setup_cintiq(wacom_wac);
wacom_setup_cintiq(wacom_wac);
break;
+ case WACOM_13HD:
+ for (i = 0; i < 9; i++)
+ __set_bit(BTN_0 + i, input_dev->keybit);
+
+ input_set_abs_params(input_dev, ABS_Z, -900, 899, 0, 0);
+ __set_bit(INPUT_PROP_DIRECT, input_dev->propbit);
+ wacom_setup_cintiq(wacom_wac);
+ break;
+
case INTUOS3:
case INTUOS3L:
__set_bit(BTN_4, input_dev->keybit);
63, WACOM_24HD, WACOM_INTUOS3_RES, WACOM_INTUOS3_RES };
static const struct wacom_features wacom_features_0xF8 =
{ "Wacom Cintiq 24HD touch", WACOM_PKGLEN_INTUOS, 104480, 65600, 2047, /* Pen */
- 63, WACOM_24HD, WACOM_INTUOS3_RES, WACOM_INTUOS3_RES, .oVid = USB_VENDOR_ID_WACOM, .oPid = 0xf6 };
+ 63, WACOM_24HD, WACOM_INTUOS3_RES, WACOM_INTUOS3_RES,
+ .oVid = USB_VENDOR_ID_WACOM, .oPid = 0xf6 };
static const struct wacom_features wacom_features_0xF6 =
{ "Wacom Cintiq 24HD touch", .type = WACOM_24HDT, /* Touch */
.oVid = USB_VENDOR_ID_WACOM, .oPid = 0xf8, .touch_max = 10 };
static const struct wacom_features wacom_features_0xC6 =
{ "Wacom Cintiq 12WX", WACOM_PKGLEN_INTUOS, 53020, 33440, 1023,
63, WACOM_BEE, WACOM_INTUOS3_RES, WACOM_INTUOS3_RES };
+static const struct wacom_features wacom_features_0x304 =
+ { "Wacom Cintiq 13HD", WACOM_PKGLEN_INTUOS, 59552, 33848, 1023,
+ 63, WACOM_13HD, WACOM_INTUOS3_RES, WACOM_INTUOS3_RES };
static const struct wacom_features wacom_features_0xC7 =
{ "Wacom DTU1931", WACOM_PKGLEN_GRAPHIRE, 37832, 30305, 511,
0, PL, WACOM_INTUOS_RES, WACOM_INTUOS_RES };
static const struct wacom_features wacom_features_0xF0 =
{ "Wacom DTU1631", WACOM_PKGLEN_GRAPHIRE, 34623, 19553, 511,
0, DTU, WACOM_INTUOS_RES, WACOM_INTUOS_RES };
+static const struct wacom_features wacom_features_0x57 =
+ { "Wacom DTK2241", WACOM_PKGLEN_INTUOS, 95840, 54260, 2047,
+ 63, DTK, WACOM_INTUOS3_RES, WACOM_INTUOS3_RES};
static const struct wacom_features wacom_features_0x59 = /* Pen */
{ "Wacom DTH2242", WACOM_PKGLEN_INTUOS, 95840, 54260, 2047,
63, DTK, WACOM_INTUOS3_RES, WACOM_INTUOS3_RES,
static const struct wacom_features wacom_features_0xFA =
{ "Wacom Cintiq 22HD", WACOM_PKGLEN_INTUOS, 95840, 54260, 2047,
63, WACOM_22HD, WACOM_INTUOS3_RES, WACOM_INTUOS3_RES };
+static const struct wacom_features wacom_features_0x5B =
+ { "Wacom Cintiq 22HDT", WACOM_PKGLEN_INTUOS, 95840, 54260, 2047,
+ 63, WACOM_22HD, WACOM_INTUOS3_RES, WACOM_INTUOS3_RES,
+ .oVid = USB_VENDOR_ID_WACOM, .oPid = 0x5e };
+static const struct wacom_features wacom_features_0x5E =
+ { "Wacom Cintiq 22HDT", .type = WACOM_24HDT,
+ .oVid = USB_VENDOR_ID_WACOM, .oPid = 0x5b, .touch_max = 10 };
static const struct wacom_features wacom_features_0x90 =
{ "Wacom ISDv4 90", WACOM_PKGLEN_GRAPHIRE, 26202, 16325, 255,
0, TABLETPC, WACOM_INTUOS_RES, WACOM_INTUOS_RES };
static const struct wacom_features wacom_features_0xE6 =
{ "Wacom ISDv4 E6", WACOM_PKGLEN_TPC2FG, 27760, 15694, 255,
0, TABLETPC2FG, WACOM_INTUOS_RES, WACOM_INTUOS_RES,
- .touch_max = 2 };
+ .touch_max = 2 };
static const struct wacom_features wacom_features_0xEC =
{ "Wacom ISDv4 EC", WACOM_PKGLEN_GRAPHIRE, 25710, 14500, 255,
0, TABLETPC, WACOM_INTUOS_RES, WACOM_INTUOS_RES };
{ USB_DEVICE_WACOM(0x43) },
{ USB_DEVICE_WACOM(0x44) },
{ USB_DEVICE_WACOM(0x45) },
+ { USB_DEVICE_WACOM(0x57) },
{ USB_DEVICE_WACOM(0x59) },
{ USB_DEVICE_DETAILED(0x5D, USB_CLASS_HID, 0, 0) },
+ { USB_DEVICE_WACOM(0x5B) },
+ { USB_DEVICE_DETAILED(0x5E, USB_CLASS_HID, 0, 0) },
{ USB_DEVICE_WACOM(0xB0) },
{ USB_DEVICE_WACOM(0xB1) },
{ USB_DEVICE_WACOM(0xB2) },
{ USB_DEVICE_WACOM(0x100) },
{ USB_DEVICE_WACOM(0x101) },
{ USB_DEVICE_WACOM(0x10D) },
+ { USB_DEVICE_WACOM(0x304) },
{ USB_DEVICE_WACOM(0x4001) },
{ USB_DEVICE_WACOM(0x47) },
{ USB_DEVICE_WACOM(0xF4) },
WACOM_24HD,
CINTIQ,
WACOM_BEE,
+ WACOM_13HD,
WACOM_MO,
WIRELESS,
BAMBOO_PT,
input_set_abs_params(input_dev,
ABS_MT_POSITION_X, 0, EGALAX_MAX_X, 0, 0);
input_set_abs_params(input_dev,
- ABS_MT_POSITION_X, 0, EGALAX_MAX_Y, 0, 0);
+ ABS_MT_POSITION_Y, 0, EGALAX_MAX_Y, 0, 0);
input_mt_init_slots(input_dev, MAX_SUPPORT_POINTS, 0);
input_set_drvdata(input_dev, ts);
static inline struct capi_ctr *get_capi_ctr_by_nr(u16 contr)
{
- if (contr - 1 >= CAPI_MAXCONTR)
+ if (contr < 1 || contr - 1 >= CAPI_MAXCONTR)
return NULL;
return capi_controller[contr - 1];
{
lockdep_assert_held(&capi_controller_lock);
- if (applid - 1 >= CAPI_MAXAPPL)
+ if (applid < 1 || applid - 1 >= CAPI_MAXAPPL)
return NULL;
return capi_applications[applid - 1];
static inline struct capi20_appl *get_capi_appl_by_nr(u16 applid)
{
- if (applid - 1 >= CAPI_MAXAPPL)
+ if (applid < 1 || applid - 1 >= CAPI_MAXAPPL)
return NULL;
return rcu_dereference(capi_applications[applid - 1]);
{
.name = "led_1",
.port = 0x49,
- .mask = BIT(7),
+ .mask = BIT(6),
},
{
.name = "led_2",
.port = 0x49,
- .mask = BIT(6),
+ .mask = BIT(5),
},
{
.name = "led_3",
.port = 0x49,
- .mask = BIT(5),
+ .mask = BIT(4),
},
{
.name = "led_4",
.port = 0x49,
- .mask = BIT(4),
+ .mask = BIT(3),
},
{
.name = "led_5",
.port = 0x49,
- .mask = BIT(3),
+ .mask = BIT(2),
},
{
.name = "led_6",
.port = 0x49,
- .mask = BIT(2),
+ .mask = BIT(1),
},
{
.name = "led_7",
.port = 0x49,
- .mask = BIT(1),
+ .mask = BIT(0),
}
};
struct zoran_mapping {
struct zoran_fh *fh;
- int count;
+ atomic_t count;
};
struct zoran_buffer {
zoran_vm_open (struct vm_area_struct *vma)
{
struct zoran_mapping *map = vma->vm_private_data;
-
- map->count++;
+ atomic_inc(&map->count);
}
static void
struct zoran *zr = fh->zr;
int i;
- if (--map->count > 0)
+ if (!atomic_dec_and_mutex_lock(&map->count, &zr->resource_lock))
return;
dprintk(3, KERN_INFO "%s: %s - munmap(%s)\n", ZR_DEVNAME(zr),
kfree(map);
/* Any buffers still mapped? */
- for (i = 0; i < fh->buffers.num_buffers; i++)
- if (fh->buffers.buffer[i].map)
+ for (i = 0; i < fh->buffers.num_buffers; i++) {
+ if (fh->buffers.buffer[i].map) {
+ mutex_unlock(&zr->resource_lock);
return;
+ }
+ }
dprintk(3, KERN_INFO "%s: %s - free %s buffers\n", ZR_DEVNAME(zr),
__func__, mode_name(fh->map_mode));
- mutex_lock(&zr->resource_lock);
if (fh->map_mode == ZORAN_MAP_MODE_RAW) {
if (fh->buffers.active != ZORAN_FREE) {
goto mmap_unlock_and_return;
}
map->fh = fh;
- map->count = 1;
+ atomic_set(&map->count, 1);
vma->vm_ops = &zoran_vm_ops;
vma->vm_flags |= VM_DONTEXPAND;
struct omap_dss_device *def_display;
struct omap2video_device *vid_dev = NULL;
+ if (omapdss_is_initialized() == false)
+ return -EPROBE_DEFER;
+
ret = omapdss_compat_init();
if (ret) {
dev_err(&pdev->dev, "failed to init dss\n");
#include <linux/irq.h>
#include <linux/interrupt.h>
-static int irq;
+static int irq = -1;
static irqreturn_t dummy_interrupt(int irq, void *dev_id)
{
static int __init dummy_irq_init(void)
{
+ if (irq < 0) {
+ printk(KERN_ERR "dummy-irq: no IRQ given. Use irq=N\n");
+ return -EIO;
+ }
if (request_irq(irq, &dummy_interrupt, IRQF_SHARED, "dummy_irq", &irq)) {
printk(KERN_ERR "dummy-irq: cannot register IRQ %d\n", irq);
return -EIO;
}
}
+ device->event_cb = NULL;
+
mutex_unlock(&dev->device_lock);
if (!device->ops || !device->ops->disable)
/* find ME client we're trying to connect to */
i = mei_me_cl_by_uuid(dev, &data->in_client_uuid);
- if (i >= 0 && !dev->me_clients[i].props.fixed_address) {
- cl->me_client_id = dev->me_clients[i].client_id;
- cl->state = MEI_FILE_CONNECTING;
+ if (i < 0 || dev->me_clients[i].props.fixed_address) {
+ dev_dbg(&dev->pdev->dev, "Cannot connect to FW Client UUID = %pUl\n",
+ &data->in_client_uuid);
+ rets = -ENODEV;
+ goto end;
}
+ cl->me_client_id = dev->me_clients[i].client_id;
+ cl->state = MEI_FILE_CONNECTING;
+
dev_dbg(&dev->pdev->dev, "Connect to FW Client ID = %d\n",
cl->me_client_id);
dev_dbg(&dev->pdev->dev, "FW Client - Protocol Version = %d\n",
goto end;
}
- if (cl->state != MEI_FILE_CONNECTING) {
- rets = -ENODEV;
- goto end;
- }
-
/* prepare the output buffer */
client = &data->out_client_properties;
rets = mei_cl_connect(cl, file);
end:
- dev_dbg(&dev->pdev->dev, "free connect cb memory.");
return rets;
}
mmc_free_host(slot->mmc);
}
-static bool atmci_filter(struct dma_chan *chan, void *slave)
+static bool atmci_filter(struct dma_chan *chan, void *pdata)
{
- struct mci_dma_data *sl = slave;
+ struct mci_platform_data *sl_pdata = pdata;
+ struct mci_dma_data *sl;
+ if (!sl_pdata)
+ return false;
+
+ sl = sl_pdata->dma_slave;
if (sl && find_slave_dev(sl) == chan->device->dev) {
chan->private = slave_data_ptr(sl);
return true;
static bool atmci_configure_dma(struct atmel_mci *host)
{
struct mci_platform_data *pdata;
+ dma_cap_mask_t mask;
if (host == NULL)
return false;
pdata = host->pdev->dev.platform_data;
- if (!pdata)
- return false;
+ dma_cap_zero(mask);
+ dma_cap_set(DMA_SLAVE, mask);
- if (pdata->dma_slave && find_slave_dev(pdata->dma_slave)) {
- dma_cap_mask_t mask;
-
- /* Try to grab a DMA channel */
- dma_cap_zero(mask);
- dma_cap_set(DMA_SLAVE, mask);
- host->dma.chan =
- dma_request_channel(mask, atmci_filter, pdata->dma_slave);
- }
+ host->dma.chan = dma_request_slave_channel_compat(mask, atmci_filter, pdata,
+ &host->pdev->dev, "rxtx");
if (!host->dma.chan) {
dev_warn(&host->pdev->dev, "no DMA channel available\n");
return false;
*/
struct regulator *vcc;
struct regulator *vcc_aux;
+ int pbias_disable;
void __iomem *base;
resource_size_t mapbase;
spinlock_t irq_lock; /* Prevent races with irq handler */
if (!host->vcc)
return 0;
/*
- * With DT, never turn OFF the regulator. This is because
+ * With DT, never turn OFF the regulator for MMC1. This is because
* the pbias cell programming support is still missing when
* booting with Device tree
*/
- if (dev->of_node && !vdd)
+ if (host->pbias_disable && !vdd)
return 0;
if (mmc_slot(host).before_set_reg)
(ios->vdd == DUAL_VOLT_OCR_BIT) &&
/*
* With pbias cell programming missing, this
- * can't be allowed when booting with device
+ * can't be allowed on MMC1 when booting with device
* tree.
*/
- !host->dev->of_node) {
+ !host->pbias_disable) {
/*
* The mmc_select_voltage fn of the core does
* not seem to set the power_mode to
omap_hsmmc_context_save(host);
+ /* This can be removed once we support PBIAS with DT */
+ if (host->dev->of_node && host->mapbase == 0x4809c000)
+ host->pbias_disable = 1;
+
host->dbclk = clk_get(&pdev->dev, "mmchsdb_fck");
/*
* MMC can still work without debounce clock.
omap_hsmmc_conf_bus_power(host);
- res = platform_get_resource_byname(pdev, IORESOURCE_DMA, "tx");
- if (!res) {
- dev_err(mmc_dev(host->mmc), "cannot get DMA TX channel\n");
- ret = -ENXIO;
- goto err_irq;
- }
- tx_req = res->start;
+ if (!pdev->dev.of_node) {
+ res = platform_get_resource_byname(pdev, IORESOURCE_DMA, "tx");
+ if (!res) {
+ dev_err(mmc_dev(host->mmc), "cannot get DMA TX channel\n");
+ ret = -ENXIO;
+ goto err_irq;
+ }
+ tx_req = res->start;
- res = platform_get_resource_byname(pdev, IORESOURCE_DMA, "rx");
- if (!res) {
- dev_err(mmc_dev(host->mmc), "cannot get DMA RX channel\n");
- ret = -ENXIO;
- goto err_irq;
+ res = platform_get_resource_byname(pdev, IORESOURCE_DMA, "rx");
+ if (!res) {
+ dev_err(mmc_dev(host->mmc), "cannot get DMA RX channel\n");
+ ret = -ENXIO;
+ goto err_irq;
+ }
+ rx_req = res->start;
}
- rx_req = res->start;
dma_cap_zero(mask);
dma_cap_set(DMA_SLAVE, mask);
- host->rx_chan = dma_request_channel(mask, omap_dma_filter_fn, &rx_req);
+ host->rx_chan =
+ dma_request_slave_channel_compat(mask, omap_dma_filter_fn,
+ &rx_req, &pdev->dev, "rx");
+
if (!host->rx_chan) {
dev_err(mmc_dev(host->mmc), "unable to obtain RX DMA engine channel %u\n", rx_req);
ret = -ENXIO;
goto err_irq;
}
- host->tx_chan = dma_request_channel(mask, omap_dma_filter_fn, &tx_req);
+ host->tx_chan =
+ dma_request_slave_channel_compat(mask, omap_dma_filter_fn,
+ &tx_req, &pdev->dev, "tx");
+
if (!host->tx_chan) {
dev_err(mmc_dev(host->mmc), "unable to obtain TX DMA engine channel %u\n", tx_req);
ret = -ENXIO;
.enable_dma = sdhci_acpi_enable_dma,
};
+static const struct sdhci_acpi_slot sdhci_acpi_slot_int_emmc = {
+ .caps = MMC_CAP_8_BIT_DATA | MMC_CAP_NONREMOVABLE,
+ .caps2 = MMC_CAP2_HC_ERASE_SZ,
+ .flags = SDHCI_ACPI_RUNTIME_PM,
+};
+
static const struct sdhci_acpi_slot sdhci_acpi_slot_int_sdio = {
.quirks2 = SDHCI_QUIRK2_HOST_OFF_CARD_ON,
.caps = MMC_CAP_NONREMOVABLE | MMC_CAP_POWER_OFF_CARD,
.pm_caps = MMC_PM_KEEP_POWER,
};
+static const struct sdhci_acpi_slot sdhci_acpi_slot_int_sd = {
+};
+
+struct sdhci_acpi_uid_slot {
+ const char *hid;
+ const char *uid;
+ const struct sdhci_acpi_slot *slot;
+};
+
+static const struct sdhci_acpi_uid_slot sdhci_acpi_uids[] = {
+ { "80860F14" , "1" , &sdhci_acpi_slot_int_emmc },
+ { "80860F14" , "3" , &sdhci_acpi_slot_int_sd },
+ { "INT33BB" , "2" , &sdhci_acpi_slot_int_sdio },
+ { "INT33C6" , NULL, &sdhci_acpi_slot_int_sdio },
+ { "PNP0D40" },
+ { },
+};
+
static const struct acpi_device_id sdhci_acpi_ids[] = {
- { "INT33C6", (kernel_ulong_t)&sdhci_acpi_slot_int_sdio },
- { "PNP0D40" },
+ { "80860F14" },
+ { "INT33BB" },
+ { "INT33C6" },
+ { "PNP0D40" },
{ },
};
MODULE_DEVICE_TABLE(acpi, sdhci_acpi_ids);
-static const struct sdhci_acpi_slot *sdhci_acpi_get_slot(const char *hid)
+static const struct sdhci_acpi_slot *sdhci_acpi_get_slot_by_ids(const char *hid,
+ const char *uid)
{
- const struct acpi_device_id *id;
-
- for (id = sdhci_acpi_ids; id->id[0]; id++)
- if (!strcmp(id->id, hid))
- return (const struct sdhci_acpi_slot *)id->driver_data;
+ const struct sdhci_acpi_uid_slot *u;
+
+ for (u = sdhci_acpi_uids; u->hid; u++) {
+ if (strcmp(u->hid, hid))
+ continue;
+ if (!u->uid)
+ return u->slot;
+ if (uid && !strcmp(u->uid, uid))
+ return u->slot;
+ }
return NULL;
}
+static const struct sdhci_acpi_slot *sdhci_acpi_get_slot(acpi_handle handle,
+ const char *hid)
+{
+ const struct sdhci_acpi_slot *slot;
+ struct acpi_device_info *info;
+ const char *uid = NULL;
+ acpi_status status;
+
+ status = acpi_get_object_info(handle, &info);
+ if (!ACPI_FAILURE(status) && (info->valid & ACPI_VALID_UID))
+ uid = info->unique_id.string;
+
+ slot = sdhci_acpi_get_slot_by_ids(hid, uid);
+
+ kfree(info);
+ return slot;
+}
+
static int sdhci_acpi_probe(struct platform_device *pdev)
{
struct device *dev = &pdev->dev;
c = sdhci_priv(host);
c->host = host;
- c->slot = sdhci_acpi_get_slot(hid);
+ c->slot = sdhci_acpi_get_slot(handle, hid);
c->pdev = pdev;
c->use_runtime_pm = sdhci_acpi_flag(c, SDHCI_ACPI_RUNTIME_PM);
goto err_free;
if (c->use_runtime_pm) {
+ pm_runtime_set_active(dev);
pm_suspend_ignore_children(dev, 1);
pm_runtime_set_autosuspend_delay(dev, 50);
pm_runtime_use_autosuspend(dev);
struct clk *clk_ipg;
struct clk *clk_ahb;
struct clk *clk_per;
+ enum {
+ NO_CMD_PENDING, /* no multiblock command pending*/
+ MULTIBLK_IN_PROCESS, /* exact multiblock cmd in process */
+ WAIT_FOR_INT, /* sent CMD12, waiting for response INT */
+ } multiblock_status;
+
};
static struct platform_device_id imx_esdhc_devtype[] = {
static u32 esdhc_readl_le(struct sdhci_host *host, int reg)
{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct pltfm_imx_data *imx_data = pltfm_host->priv;
u32 val = readl(host->ioaddr + reg);
if (unlikely(reg == SDHCI_CAPABILITIES)) {
val &= ~ESDHC_INT_VENDOR_SPEC_DMA_ERR;
val |= SDHCI_INT_ADMA_ERROR;
}
+
+ /*
+ * mask off the interrupt we get in response to the manually
+ * sent CMD12
+ */
+ if ((imx_data->multiblock_status == WAIT_FOR_INT) &&
+ ((val & SDHCI_INT_RESPONSE) == SDHCI_INT_RESPONSE)) {
+ val &= ~SDHCI_INT_RESPONSE;
+ writel(SDHCI_INT_RESPONSE, host->ioaddr +
+ SDHCI_INT_STATUS);
+ imx_data->multiblock_status = NO_CMD_PENDING;
+ }
}
return val;
v = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
v &= ~ESDHC_VENDOR_SPEC_SDIO_QUIRK;
writel(v, host->ioaddr + ESDHC_VENDOR_SPEC);
+
+ if (imx_data->multiblock_status == MULTIBLK_IN_PROCESS)
+ {
+ /* send a manual CMD12 with RESPTYP=none */
+ data = MMC_STOP_TRANSMISSION << 24 |
+ SDHCI_CMD_ABORTCMD << 16;
+ writel(data, host->ioaddr + SDHCI_TRANSFER_MODE);
+ imx_data->multiblock_status = WAIT_FOR_INT;
+ }
}
if (unlikely(reg == SDHCI_INT_ENABLE || reg == SDHCI_SIGNAL_ENABLE)) {
}
return;
case SDHCI_COMMAND:
- if ((host->cmd->opcode == MMC_STOP_TRANSMISSION ||
- host->cmd->opcode == MMC_SET_BLOCK_COUNT) &&
- (imx_data->flags & ESDHC_FLAG_MULTIBLK_NO_INT))
+ if (host->cmd->opcode == MMC_STOP_TRANSMISSION)
val |= SDHCI_CMD_ABORTCMD;
+ if ((host->cmd->opcode == MMC_SET_BLOCK_COUNT) &&
+ (imx_data->flags & ESDHC_FLAG_MULTIBLK_NO_INT))
+ imx_data->multiblock_status = MULTIBLK_IN_PROCESS;
+
if (is_imx6q_usdhc(imx_data))
writel(val << 16,
host->ioaddr + SDHCI_TRANSFER_MODE);
/*
* Do not touch buswidth bits here. This is done in
* esdhc_pltfm_bus_width.
+ * Do not touch the D3CD bit either which is used for the
+ * SDIO interrupt errata workaround.
*/
- mask = 0xffff & ~ESDHC_CTRL_BUSWIDTH_MASK;
+ mask = 0xffff & ~(ESDHC_CTRL_BUSWIDTH_MASK | ESDHC_CTRL_D3CD);
esdhc_clrset_le(host, mask, new_val, reg);
return;
*/
#define PCI_DEVICE_ID_INTEL_PCH_SDIO0 0x8809
#define PCI_DEVICE_ID_INTEL_PCH_SDIO1 0x880a
+#define PCI_DEVICE_ID_INTEL_BYT_EMMC 0x0f14
+#define PCI_DEVICE_ID_INTEL_BYT_SDIO 0x0f15
+#define PCI_DEVICE_ID_INTEL_BYT_SD 0x0f16
/*
* PCI registers
.probe_slot = pch_hc_probe_slot,
};
+static int byt_emmc_probe_slot(struct sdhci_pci_slot *slot)
+{
+ slot->host->mmc->caps |= MMC_CAP_8_BIT_DATA | MMC_CAP_NONREMOVABLE;
+ slot->host->mmc->caps2 |= MMC_CAP2_HC_ERASE_SZ;
+ return 0;
+}
+
+static int byt_sdio_probe_slot(struct sdhci_pci_slot *slot)
+{
+ slot->host->mmc->caps |= MMC_CAP_POWER_OFF_CARD | MMC_CAP_NONREMOVABLE;
+ return 0;
+}
+
+static const struct sdhci_pci_fixes sdhci_intel_byt_emmc = {
+ .allow_runtime_pm = true,
+ .probe_slot = byt_emmc_probe_slot,
+};
+
+static const struct sdhci_pci_fixes sdhci_intel_byt_sdio = {
+ .quirks2 = SDHCI_QUIRK2_HOST_OFF_CARD_ON,
+ .allow_runtime_pm = true,
+ .probe_slot = byt_sdio_probe_slot,
+};
+
+static const struct sdhci_pci_fixes sdhci_intel_byt_sd = {
+};
+
/* O2Micro extra registers */
#define O2_SD_LOCK_WP 0xD3
#define O2_SD_MULTI_VCC3V 0xEE
.driver_data = (kernel_ulong_t)&sdhci_intel_pch_sdio,
},
+ {
+ .vendor = PCI_VENDOR_ID_INTEL,
+ .device = PCI_DEVICE_ID_INTEL_BYT_EMMC,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .driver_data = (kernel_ulong_t)&sdhci_intel_byt_emmc,
+ },
+
+ {
+ .vendor = PCI_VENDOR_ID_INTEL,
+ .device = PCI_DEVICE_ID_INTEL_BYT_SDIO,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .driver_data = (kernel_ulong_t)&sdhci_intel_byt_sdio,
+ },
+
+ {
+ .vendor = PCI_VENDOR_ID_INTEL,
+ .device = PCI_DEVICE_ID_INTEL_BYT_SD,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .driver_data = (kernel_ulong_t)&sdhci_intel_byt_sd,
+ },
+
{
.vendor = PCI_VENDOR_ID_O2,
.device = PCI_DEVICE_ID_O2_8120,
}
/**
- * bond_3ad_get_active_agg_info - get information of the active aggregator
+ * __bond_3ad_get_active_agg_info - get information of the active aggregator
* @bond: bonding struct to work on
* @ad_info: ad_info struct to fill with the bond's info
*
* Returns: 0 on success
* < 0 on error
*/
-int bond_3ad_get_active_agg_info(struct bonding *bond, struct ad_info *ad_info)
+int __bond_3ad_get_active_agg_info(struct bonding *bond,
+ struct ad_info *ad_info)
{
struct aggregator *aggregator = NULL;
struct port *port;
return -1;
}
+/* Wrapper used to hold bond->lock so no slave manipulation can occur */
+int bond_3ad_get_active_agg_info(struct bonding *bond, struct ad_info *ad_info)
+{
+ int ret;
+
+ read_lock(&bond->lock);
+ ret = __bond_3ad_get_active_agg_info(bond, ad_info);
+ read_unlock(&bond->lock);
+
+ return ret;
+}
+
int bond_3ad_xmit_xor(struct sk_buff *skb, struct net_device *dev)
{
struct slave *slave, *start_at;
struct ad_info ad_info;
int res = 1;
- if (bond_3ad_get_active_agg_info(bond, &ad_info)) {
- pr_debug("%s: Error: bond_3ad_get_active_agg_info failed\n",
+ if (__bond_3ad_get_active_agg_info(bond, &ad_info)) {
+ pr_debug("%s: Error: __bond_3ad_get_active_agg_info failed\n",
dev->name);
goto out;
}
void bond_3ad_adapter_duplex_changed(struct slave *slave);
void bond_3ad_handle_link_change(struct slave *slave, char link);
int bond_3ad_get_active_agg_info(struct bonding *bond, struct ad_info *ad_info);
+int __bond_3ad_get_active_agg_info(struct bonding *bond,
+ struct ad_info *ad_info);
int bond_3ad_xmit_xor(struct sk_buff *skb, struct net_device *dev);
int bond_3ad_lacpdu_recv(const struct sk_buff *skb, struct bonding *bond,
struct slave *slave);
slave->dev->features,
mask);
}
+ features = netdev_add_tso_features(features, mask);
out:
read_unlock(&bond->lock);
{
struct sk_buff *skb;
- pr_debug("arp %d on slave %s: dst %x src %x vid %d\n", arp_op,
- slave_dev->name, dest_ip, src_ip, vlan_id);
+ pr_debug("arp %d on slave %s: dst %pI4 src %pI4 vid %d\n", arp_op,
+ slave_dev->name, &dest_ip, &src_ip, vlan_id);
skb = arp_create(arp_op, ETH_P_ARP, dest_ip, slave_dev, src_ip,
NULL, slave_dev->dev_addr, NULL);
__be32 addr;
if (!targets[i])
break;
- pr_debug("basa: target %x\n", targets[i]);
+ pr_debug("basa: target %pI4\n", &targets[i]);
if (!bond_vlan_used(bond)) {
pr_debug("basa: empty vlan: arp_send\n");
addr = bond_confirm_addr(bond->dev, targets[i], 0);
static int bond_check_params(struct bond_params *params)
{
- int arp_validate_value, fail_over_mac_value, primary_reselect_value;
+ int arp_validate_value, fail_over_mac_value, primary_reselect_value, i;
/*
* Convert string parameters.
arp_interval = BOND_LINK_ARP_INTERV;
}
- for (arp_ip_count = 0;
- (arp_ip_count < BOND_MAX_ARP_TARGETS) && arp_ip_target[arp_ip_count];
- arp_ip_count++) {
+ for (arp_ip_count = 0, i = 0;
+ (arp_ip_count < BOND_MAX_ARP_TARGETS) && arp_ip_target[i]; i++) {
/* not complete check, but should be good enough to
catch mistakes */
- __be32 ip = in_aton(arp_ip_target[arp_ip_count]);
- if (!isdigit(arp_ip_target[arp_ip_count][0]) ||
- ip == 0 || ip == htonl(INADDR_BROADCAST)) {
+ __be32 ip = in_aton(arp_ip_target[i]);
+ if (!isdigit(arp_ip_target[i][0]) || ip == 0 ||
+ ip == htonl(INADDR_BROADCAST)) {
pr_warning("Warning: bad arp_ip_target module parameter (%s), ARP monitoring will not be performed\n",
- arp_ip_target[arp_ip_count]);
+ arp_ip_target[i]);
arp_interval = 0;
} else {
- arp_target[arp_ip_count] = ip;
+ arp_target[arp_ip_count++] = ip;
}
}
if (miimon) {
pr_info("MII link monitoring set to %d ms\n", miimon);
} else if (arp_interval) {
- int i;
-
pr_info("ARP monitoring set to %d ms, validate %s, with %d target(s):",
arp_interval,
arp_validate_tbl[arp_validate_value].modename,
seq_printf(seq, "Aggregator selection policy (ad_select): %s\n",
ad_select_tbl[bond->params.ad_select].modename);
- if (bond_3ad_get_active_agg_info(bond, &ad_info)) {
+ if (__bond_3ad_get_active_agg_info(bond, &ad_info)) {
seq_printf(seq, "bond %s has no active aggregator\n",
bond->dev->name);
} else {
int new_value, ret = count;
struct bonding *bond = to_bond(d);
+ if (!rtnl_trylock())
+ return restart_syscall();
+
if (bond->dev->flags & IFF_UP) {
pr_err("unable to update mode of %s because interface is up.\n",
bond->dev->name);
bond->dev->name, bond_mode_tbl[new_value].modename,
new_value);
out:
+ rtnl_unlock();
return ret;
}
static DEVICE_ATTR(mode, S_IRUGO | S_IWUSR,
}
static DEVICE_ATTR(mii_status, S_IRUGO, bonding_show_mii_status, NULL);
-
/*
* Show current 802.3ad aggregator ID.
*/
if (bond->params.mode == BOND_MODE_8023AD) {
struct ad_info ad_info;
count = sprintf(buf, "%d\n",
- (bond_3ad_get_active_agg_info(bond, &ad_info))
+ bond_3ad_get_active_agg_info(bond, &ad_info)
? 0 : ad_info.aggregator_id);
}
if (bond->params.mode == BOND_MODE_8023AD) {
struct ad_info ad_info;
count = sprintf(buf, "%d\n",
- (bond_3ad_get_active_agg_info(bond, &ad_info))
+ bond_3ad_get_active_agg_info(bond, &ad_info)
? 0 : ad_info.ports);
}
if (bond->params.mode == BOND_MODE_8023AD) {
struct ad_info ad_info;
count = sprintf(buf, "%d\n",
- (bond_3ad_get_active_agg_info(bond, &ad_info))
+ bond_3ad_get_active_agg_info(bond, &ad_info)
? 0 : ad_info.actor_key);
}
if (bond->params.mode == BOND_MODE_8023AD) {
struct ad_info ad_info;
count = sprintf(buf, "%d\n",
- (bond_3ad_get_active_agg_info(bond, &ad_info))
+ bond_3ad_get_active_agg_info(bond, &ad_info)
? 0 : ad_info.partner_key);
}
{
struct esd_usb2 *dev = priv->usb2;
struct net_device *netdev = priv->netdev;
- struct esd_usb2_msg msg;
+ struct esd_usb2_msg *msg;
int err, i;
+ msg = kmalloc(sizeof(*msg), GFP_KERNEL);
+ if (!msg) {
+ err = -ENOMEM;
+ goto out;
+ }
+
/*
* Enable all IDs
* The IDADD message takes up to 64 32 bit bitmasks (2048 bits).
* the number of the starting bitmask (0..64) to the filter.option
* field followed by only some bitmasks.
*/
- msg.msg.hdr.cmd = CMD_IDADD;
- msg.msg.hdr.len = 2 + ESD_MAX_ID_SEGMENT;
- msg.msg.filter.net = priv->index;
- msg.msg.filter.option = ESD_ID_ENABLE; /* start with segment 0 */
+ msg->msg.hdr.cmd = CMD_IDADD;
+ msg->msg.hdr.len = 2 + ESD_MAX_ID_SEGMENT;
+ msg->msg.filter.net = priv->index;
+ msg->msg.filter.option = ESD_ID_ENABLE; /* start with segment 0 */
for (i = 0; i < ESD_MAX_ID_SEGMENT; i++)
- msg.msg.filter.mask[i] = cpu_to_le32(0xffffffff);
+ msg->msg.filter.mask[i] = cpu_to_le32(0xffffffff);
/* enable 29bit extended IDs */
- msg.msg.filter.mask[ESD_MAX_ID_SEGMENT] = cpu_to_le32(0x00000001);
+ msg->msg.filter.mask[ESD_MAX_ID_SEGMENT] = cpu_to_le32(0x00000001);
- err = esd_usb2_send_msg(dev, &msg);
+ err = esd_usb2_send_msg(dev, msg);
if (err)
- goto failed;
+ goto out;
err = esd_usb2_setup_rx_urbs(dev);
if (err)
- goto failed;
+ goto out;
priv->can.state = CAN_STATE_ERROR_ACTIVE;
- return 0;
-
-failed:
+out:
if (err == -ENODEV)
netif_device_detach(netdev);
+ if (err)
+ netdev_err(netdev, "couldn't start device: %d\n", err);
- netdev_err(netdev, "couldn't start device: %d\n", err);
-
+ kfree(msg);
return err;
}
static int esd_usb2_close(struct net_device *netdev)
{
struct esd_usb2_net_priv *priv = netdev_priv(netdev);
- struct esd_usb2_msg msg;
+ struct esd_usb2_msg *msg;
int i;
+ msg = kmalloc(sizeof(*msg), GFP_KERNEL);
+ if (!msg)
+ return -ENOMEM;
+
/* Disable all IDs (see esd_usb2_start()) */
- msg.msg.hdr.cmd = CMD_IDADD;
- msg.msg.hdr.len = 2 + ESD_MAX_ID_SEGMENT;
- msg.msg.filter.net = priv->index;
- msg.msg.filter.option = ESD_ID_ENABLE; /* start with segment 0 */
+ msg->msg.hdr.cmd = CMD_IDADD;
+ msg->msg.hdr.len = 2 + ESD_MAX_ID_SEGMENT;
+ msg->msg.filter.net = priv->index;
+ msg->msg.filter.option = ESD_ID_ENABLE; /* start with segment 0 */
for (i = 0; i <= ESD_MAX_ID_SEGMENT; i++)
- msg.msg.filter.mask[i] = 0;
- if (esd_usb2_send_msg(priv->usb2, &msg) < 0)
+ msg->msg.filter.mask[i] = 0;
+ if (esd_usb2_send_msg(priv->usb2, msg) < 0)
netdev_err(netdev, "sending idadd message failed\n");
/* set CAN controller to reset mode */
- msg.msg.hdr.len = 2;
- msg.msg.hdr.cmd = CMD_SETBAUD;
- msg.msg.setbaud.net = priv->index;
- msg.msg.setbaud.rsvd = 0;
- msg.msg.setbaud.baud = cpu_to_le32(ESD_USB2_NO_BAUDRATE);
- if (esd_usb2_send_msg(priv->usb2, &msg) < 0)
+ msg->msg.hdr.len = 2;
+ msg->msg.hdr.cmd = CMD_SETBAUD;
+ msg->msg.setbaud.net = priv->index;
+ msg->msg.setbaud.rsvd = 0;
+ msg->msg.setbaud.baud = cpu_to_le32(ESD_USB2_NO_BAUDRATE);
+ if (esd_usb2_send_msg(priv->usb2, msg) < 0)
netdev_err(netdev, "sending setbaud message failed\n");
priv->can.state = CAN_STATE_STOPPED;
close_candev(netdev);
+ kfree(msg);
+
return 0;
}
{
struct esd_usb2_net_priv *priv = netdev_priv(netdev);
struct can_bittiming *bt = &priv->can.bittiming;
- struct esd_usb2_msg msg;
+ struct esd_usb2_msg *msg;
+ int err;
u32 canbtr;
int sjw_shift;
if (priv->can.ctrlmode & CAN_CTRLMODE_3_SAMPLES)
canbtr |= ESD_USB2_3_SAMPLES;
- msg.msg.hdr.len = 2;
- msg.msg.hdr.cmd = CMD_SETBAUD;
- msg.msg.setbaud.net = priv->index;
- msg.msg.setbaud.rsvd = 0;
- msg.msg.setbaud.baud = cpu_to_le32(canbtr);
+ msg = kmalloc(sizeof(*msg), GFP_KERNEL);
+ if (!msg)
+ return -ENOMEM;
+
+ msg->msg.hdr.len = 2;
+ msg->msg.hdr.cmd = CMD_SETBAUD;
+ msg->msg.setbaud.net = priv->index;
+ msg->msg.setbaud.rsvd = 0;
+ msg->msg.setbaud.baud = cpu_to_le32(canbtr);
netdev_info(netdev, "setting BTR=%#x\n", canbtr);
- return esd_usb2_send_msg(priv->usb2, &msg);
+ err = esd_usb2_send_msg(priv->usb2, msg);
+
+ kfree(msg);
+ return err;
}
static int esd_usb2_get_berr_counter(const struct net_device *netdev,
const struct usb_device_id *id)
{
struct esd_usb2 *dev;
- struct esd_usb2_msg msg;
+ struct esd_usb2_msg *msg;
int i, err;
dev = kzalloc(sizeof(*dev), GFP_KERNEL);
usb_set_intfdata(intf, dev);
+ msg = kmalloc(sizeof(*msg), GFP_KERNEL);
+ if (!msg) {
+ err = -ENOMEM;
+ goto free_msg;
+ }
+
/* query number of CAN interfaces (nets) */
- msg.msg.hdr.cmd = CMD_VERSION;
- msg.msg.hdr.len = 2;
- msg.msg.version.rsvd = 0;
- msg.msg.version.flags = 0;
- msg.msg.version.drv_version = 0;
+ msg->msg.hdr.cmd = CMD_VERSION;
+ msg->msg.hdr.len = 2;
+ msg->msg.version.rsvd = 0;
+ msg->msg.version.flags = 0;
+ msg->msg.version.drv_version = 0;
- err = esd_usb2_send_msg(dev, &msg);
+ err = esd_usb2_send_msg(dev, msg);
if (err < 0) {
dev_err(&intf->dev, "sending version message failed\n");
- goto free_dev;
+ goto free_msg;
}
- err = esd_usb2_wait_msg(dev, &msg);
+ err = esd_usb2_wait_msg(dev, msg);
if (err < 0) {
dev_err(&intf->dev, "no version message answer\n");
- goto free_dev;
+ goto free_msg;
}
- dev->net_count = (int)msg.msg.version_reply.nets;
- dev->version = le32_to_cpu(msg.msg.version_reply.version);
+ dev->net_count = (int)msg->msg.version_reply.nets;
+ dev->version = le32_to_cpu(msg->msg.version_reply.version);
if (device_create_file(&intf->dev, &dev_attr_firmware))
dev_err(&intf->dev,
for (i = 0; i < dev->net_count; i++)
esd_usb2_probe_one_net(intf, i);
- return 0;
-
-free_dev:
- kfree(dev);
+free_msg:
+ kfree(msg);
+ if (err)
+ kfree(dev);
done:
return err;
}
#define KVASER_CTRL_MODE_SELFRECEPTION 3
#define KVASER_CTRL_MODE_OFF 4
+/* log message */
+#define KVASER_EXTENDED_FRAME BIT(31)
+
struct kvaser_msg_simple {
u8 tid;
u8 channel;
priv = dev->nets[channel];
stats = &priv->netdev->stats;
- if (msg->u.rx_can.flag & (MSG_FLAG_ERROR_FRAME | MSG_FLAG_NERR |
- MSG_FLAG_OVERRUN)) {
+ if ((msg->u.rx_can.flag & MSG_FLAG_ERROR_FRAME) &&
+ (msg->id == CMD_LOG_MESSAGE)) {
+ kvaser_usb_rx_error(dev, msg);
+ return;
+ } else if (msg->u.rx_can.flag & (MSG_FLAG_ERROR_FRAME |
+ MSG_FLAG_NERR |
+ MSG_FLAG_OVERRUN)) {
kvaser_usb_rx_can_err(priv, msg);
return;
} else if (msg->u.rx_can.flag & ~MSG_FLAG_REMOTE_FRAME) {
return;
}
- cf->can_id = ((msg->u.rx_can.msg[0] & 0x1f) << 6) |
- (msg->u.rx_can.msg[1] & 0x3f);
- cf->can_dlc = get_can_dlc(msg->u.rx_can.msg[5]);
+ if (msg->id == CMD_LOG_MESSAGE) {
+ cf->can_id = le32_to_cpu(msg->u.log_message.id);
+ if (cf->can_id & KVASER_EXTENDED_FRAME)
+ cf->can_id &= CAN_EFF_MASK | CAN_EFF_FLAG;
+ else
+ cf->can_id &= CAN_SFF_MASK;
- if (msg->id == CMD_RX_EXT_MESSAGE) {
- cf->can_id <<= 18;
- cf->can_id |= ((msg->u.rx_can.msg[2] & 0x0f) << 14) |
- ((msg->u.rx_can.msg[3] & 0xff) << 6) |
- (msg->u.rx_can.msg[4] & 0x3f);
- cf->can_id |= CAN_EFF_FLAG;
- }
+ cf->can_dlc = get_can_dlc(msg->u.log_message.dlc);
- if (msg->u.rx_can.flag & MSG_FLAG_REMOTE_FRAME)
- cf->can_id |= CAN_RTR_FLAG;
- else
- memcpy(cf->data, &msg->u.rx_can.msg[6], cf->can_dlc);
+ if (msg->u.log_message.flags & MSG_FLAG_REMOTE_FRAME)
+ cf->can_id |= CAN_RTR_FLAG;
+ else
+ memcpy(cf->data, &msg->u.log_message.data,
+ cf->can_dlc);
+ } else {
+ cf->can_id = ((msg->u.rx_can.msg[0] & 0x1f) << 6) |
+ (msg->u.rx_can.msg[1] & 0x3f);
+
+ if (msg->id == CMD_RX_EXT_MESSAGE) {
+ cf->can_id <<= 18;
+ cf->can_id |= ((msg->u.rx_can.msg[2] & 0x0f) << 14) |
+ ((msg->u.rx_can.msg[3] & 0xff) << 6) |
+ (msg->u.rx_can.msg[4] & 0x3f);
+ cf->can_id |= CAN_EFF_FLAG;
+ }
+
+ cf->can_dlc = get_can_dlc(msg->u.rx_can.msg[5]);
+
+ if (msg->u.rx_can.flag & MSG_FLAG_REMOTE_FRAME)
+ cf->can_id |= CAN_RTR_FLAG;
+ else
+ memcpy(cf->data, &msg->u.rx_can.msg[6],
+ cf->can_dlc);
+ }
netif_rx(skb);
case CMD_RX_STD_MESSAGE:
case CMD_RX_EXT_MESSAGE:
+ case CMD_LOG_MESSAGE:
kvaser_usb_rx_can_msg(dev, msg);
break;
kvaser_usb_rx_error(dev, msg);
break;
- case CMD_LOG_MESSAGE:
- if (msg->u.log_message.flags & MSG_FLAG_ERROR_FRAME)
- kvaser_usb_rx_error(dev, msg);
- break;
-
case CMD_TX_ACKNOWLEDGE:
kvaser_usb_tx_acknowledge(dev, msg);
break;
return usb_submit_urb(urb, GFP_ATOMIC);
}
-static void pcan_usb_pro_drv_loaded(struct peak_usb_device *dev, int loaded)
+static int pcan_usb_pro_drv_loaded(struct peak_usb_device *dev, int loaded)
{
- u8 buffer[16];
+ u8 *buffer;
+ int err;
+
+ buffer = kmalloc(PCAN_USBPRO_FCT_DRVLD_REQ_LEN, GFP_KERNEL);
+ if (!buffer)
+ return -ENOMEM;
buffer[0] = 0;
buffer[1] = !!loaded;
- pcan_usb_pro_send_req(dev, PCAN_USBPRO_REQ_FCT,
- PCAN_USBPRO_FCT_DRVLD, buffer, sizeof(buffer));
+ err = pcan_usb_pro_send_req(dev, PCAN_USBPRO_REQ_FCT,
+ PCAN_USBPRO_FCT_DRVLD, buffer,
+ PCAN_USBPRO_FCT_DRVLD_REQ_LEN);
+ kfree(buffer);
+
+ return err;
}
static inline
*/
static int pcan_usb_pro_init(struct peak_usb_device *dev)
{
- struct pcan_usb_pro_interface *usb_if;
struct pcan_usb_pro_device *pdev =
container_of(dev, struct pcan_usb_pro_device, dev);
+ struct pcan_usb_pro_interface *usb_if = NULL;
+ struct pcan_usb_pro_fwinfo *fi = NULL;
+ struct pcan_usb_pro_blinfo *bi = NULL;
+ int err;
/* do this for 1st channel only */
if (!dev->prev_siblings) {
- struct pcan_usb_pro_fwinfo fi;
- struct pcan_usb_pro_blinfo bi;
- int err;
-
/* allocate netdevices common structure attached to first one */
usb_if = kzalloc(sizeof(struct pcan_usb_pro_interface),
GFP_KERNEL);
- if (!usb_if)
- return -ENOMEM;
+ fi = kmalloc(sizeof(struct pcan_usb_pro_fwinfo), GFP_KERNEL);
+ bi = kmalloc(sizeof(struct pcan_usb_pro_blinfo), GFP_KERNEL);
+ if (!usb_if || !fi || !bi) {
+ err = -ENOMEM;
+ goto err_out;
+ }
/* number of ts msgs to ignore before taking one into account */
usb_if->cm_ignore_count = 5;
*/
err = pcan_usb_pro_send_req(dev, PCAN_USBPRO_REQ_INFO,
PCAN_USBPRO_INFO_FW,
- &fi, sizeof(fi));
+ fi, sizeof(*fi));
if (err) {
- kfree(usb_if);
dev_err(dev->netdev->dev.parent,
"unable to read %s firmware info (err %d)\n",
pcan_usb_pro.name, err);
- return err;
+ goto err_out;
}
err = pcan_usb_pro_send_req(dev, PCAN_USBPRO_REQ_INFO,
PCAN_USBPRO_INFO_BL,
- &bi, sizeof(bi));
+ bi, sizeof(*bi));
if (err) {
- kfree(usb_if);
dev_err(dev->netdev->dev.parent,
"unable to read %s bootloader info (err %d)\n",
pcan_usb_pro.name, err);
- return err;
+ goto err_out;
}
+ /* tell the device the can driver is running */
+ err = pcan_usb_pro_drv_loaded(dev, 1);
+ if (err)
+ goto err_out;
+
dev_info(dev->netdev->dev.parent,
"PEAK-System %s hwrev %u serial %08X.%08X (%u channels)\n",
pcan_usb_pro.name,
- bi.hw_rev, bi.serial_num_hi, bi.serial_num_lo,
+ bi->hw_rev, bi->serial_num_hi, bi->serial_num_lo,
pcan_usb_pro.ctrl_count);
-
- /* tell the device the can driver is running */
- pcan_usb_pro_drv_loaded(dev, 1);
} else {
usb_if = pcan_usb_pro_dev_if(dev->prev_siblings);
}
pcan_usb_pro_set_led(dev, 0, 1);
return 0;
+
+ err_out:
+ kfree(bi);
+ kfree(fi);
+ kfree(usb_if);
+
+ return err;
}
static void pcan_usb_pro_exit(struct peak_usb_device *dev)
/* Vendor Request value for XXX_FCT */
#define PCAN_USBPRO_FCT_DRVLD 5 /* tell device driver is loaded */
+#define PCAN_USBPRO_FCT_DRVLD_REQ_LEN 16
/* PCAN_USBPRO_INFO_BL vendor request record type */
struct __packed pcan_usb_pro_blinfo {
rc |= XMIT_CSUM_TCP;
if (skb_is_gso_v6(skb)) {
- rc |= (XMIT_GSO_V6 | XMIT_CSUM_TCP | XMIT_CSUM_V6);
+ rc |= (XMIT_GSO_V6 | XMIT_CSUM_TCP);
if (rc & XMIT_CSUM_ENC)
rc |= XMIT_GSO_ENC_V6;
} else if (skb_is_gso(skb)) {
- rc |= (XMIT_GSO_V4 | XMIT_CSUM_V4 | XMIT_CSUM_TCP);
+ rc |= (XMIT_GSO_V4 | XMIT_CSUM_TCP);
if (rc & XMIT_CSUM_ENC)
rc |= XMIT_GSO_ENC_V4;
}
*/
static void bnx2x_set_pbd_gso(struct sk_buff *skb,
struct eth_tx_parse_bd_e1x *pbd,
+ struct eth_tx_start_bd *tx_start_bd,
u32 xmit_type)
{
pbd->lso_mss = cpu_to_le16(skb_shinfo(skb)->gso_size);
ip_hdr(skb)->daddr,
0, IPPROTO_TCP, 0));
- } else
+ /* GSO on 57710/57711 needs FW to calculate IP checksum */
+ tx_start_bd->bd_flags.as_bitfield |= ETH_TX_BD_FLAGS_IP_CSUM;
+ } else {
pbd->tcp_pseudo_csum =
bswab16(~csum_ipv6_magic(&ipv6_hdr(skb)->saddr,
&ipv6_hdr(skb)->daddr,
0, IPPROTO_TCP, 0));
+ }
pbd->global_data |=
cpu_to_le16(ETH_TX_PARSE_BD_E1X_PSEUDO_CS_WITHOUT_LEN);
{
u16 hlen_w = 0;
u8 outerip_off, outerip_len = 0;
+
/* from outer IP to transport */
hlen_w = (skb_inner_transport_header(skb) -
skb_network_header(skb)) >> 1;
/* transport len */
- if (xmit_type & XMIT_CSUM_TCP)
- hlen_w += inner_tcp_hdrlen(skb) >> 1;
- else
- hlen_w += sizeof(struct udphdr) >> 1;
+ hlen_w += inner_tcp_hdrlen(skb) >> 1;
pbd2->fw_ip_hdr_to_payload_w = hlen_w;
- if (xmit_type & XMIT_CSUM_ENC_V4) {
+ /* outer IP header info */
+ if (xmit_type & XMIT_CSUM_V4) {
struct iphdr *iph = ip_hdr(skb);
pbd2->fw_ip_csum_wo_len_flags_frag =
bswab16(csum_fold((~iph->check) -
bnx2x_set_pbd_gso_e2(skb, &pbd_e2_parsing_data,
xmit_type);
else
- bnx2x_set_pbd_gso(skb, pbd_e1x, xmit_type);
+ bnx2x_set_pbd_gso(skb, pbd_e1x, first_bd, xmit_type);
}
/* Set the PBD's parsing_data field if not zero
#define DRV_MODULE_NAME "tg3"
#define TG3_MAJ_NUM 3
-#define TG3_MIN_NUM 131
+#define TG3_MIN_NUM 132
#define DRV_MODULE_VERSION \
__stringify(TG3_MAJ_NUM) "." __stringify(TG3_MIN_NUM)
-#define DRV_MODULE_RELDATE "April 09, 2013"
+#define DRV_MODULE_RELDATE "May 21, 2013"
#define RESET_KIND_SHUTDOWN 0
#define RESET_KIND_INIT 1
return 0;
}
+static bool tg3_phy_power_bug(struct tg3 *tp)
+{
+ switch (tg3_asic_rev(tp)) {
+ case ASIC_REV_5700:
+ case ASIC_REV_5704:
+ return true;
+ case ASIC_REV_5780:
+ if (tp->phy_flags & TG3_PHYFLG_MII_SERDES)
+ return true;
+ return false;
+ case ASIC_REV_5717:
+ if (!tp->pci_fn)
+ return true;
+ return false;
+ case ASIC_REV_5719:
+ case ASIC_REV_5720:
+ if ((tp->phy_flags & TG3_PHYFLG_PHY_SERDES) &&
+ !tp->pci_fn)
+ return true;
+ return false;
+ }
+
+ return false;
+}
+
static void tg3_power_down_phy(struct tg3 *tp, bool do_low_power)
{
u32 val;
/* The PHY should not be powered down on some chips because
* of bugs.
*/
- if (tg3_asic_rev(tp) == ASIC_REV_5700 ||
- tg3_asic_rev(tp) == ASIC_REV_5704 ||
- (tg3_asic_rev(tp) == ASIC_REV_5780 &&
- (tp->phy_flags & TG3_PHYFLG_MII_SERDES)) ||
- (tg3_asic_rev(tp) == ASIC_REV_5717 &&
- !tp->pci_fn))
+ if (tg3_phy_power_bug(tp))
return;
if (tg3_chip_rev(tp) == CHIPREV_5784_AX ||
return (base > 0xffffdcc0) && (base + len + 8 < base);
}
+/* Test for TSO DMA buffers that cross into regions which are within MSS bytes
+ * of any 4GB boundaries: 4G, 8G, etc
+ */
+static inline int tg3_4g_tso_overflow_test(struct tg3 *tp, dma_addr_t mapping,
+ u32 len, u32 mss)
+{
+ if (tg3_asic_rev(tp) == ASIC_REV_5762 && mss) {
+ u32 base = (u32) mapping & 0xffffffff;
+
+ return ((base + len + (mss & 0x3fff)) < base);
+ }
+ return 0;
+}
+
/* Test for DMA addresses > 40-bit */
static inline int tg3_40bit_overflow_test(struct tg3 *tp, dma_addr_t mapping,
int len)
if (tg3_4g_overflow_test(map, len))
hwbug = true;
+ if (tg3_4g_tso_overflow_test(tp, map, len, mss))
+ hwbug = true;
+
if (tg3_40bit_overflow_test(tp, map, len))
hwbug = true;
tg3_halt_cpu(tp, RX_CPU_BASE);
}
+ err = tg3_poll_fw(tp);
+ if (err)
+ return err;
+
tw32(GRC_MODE, tp->grc_mode);
if (tg3_chip_rev_id(tp) == CHIPREV_ID_5705_A0) {
tg3_ape_unlock(tp, TG3_APE_LOCK_GRC);
- err = tg3_poll_fw(tp);
- if (err)
- return err;
-
tg3_mdio_start(tp);
if (tg3_flag(tp, PCI_EXPRESS) &&
}
}
+static inline u32 tg3_lso_rd_dma_workaround_bit(struct tg3 *tp)
+{
+ if (tg3_asic_rev(tp) == ASIC_REV_5719)
+ return TG3_LSO_RD_DMA_TX_LENGTH_WA_5719;
+ else
+ return TG3_LSO_RD_DMA_TX_LENGTH_WA_5720;
+}
+
/* tp->lock is held. */
static int tg3_reset_hw(struct tg3 *tp, bool reset_phy)
{
tw32_f(RDMAC_MODE, rdmac_mode);
udelay(40);
- if (tg3_asic_rev(tp) == ASIC_REV_5719) {
+ if (tg3_asic_rev(tp) == ASIC_REV_5719 ||
+ tg3_asic_rev(tp) == ASIC_REV_5720) {
for (i = 0; i < TG3_NUM_RDMA_CHANNELS; i++) {
if (tr32(TG3_RDMA_LENGTH + (i << 2)) > TG3_MAX_MTU(tp))
break;
}
if (i < TG3_NUM_RDMA_CHANNELS) {
val = tr32(TG3_LSO_RD_DMA_CRPTEN_CTRL);
- val |= TG3_LSO_RD_DMA_TX_LENGTH_WA;
+ val |= tg3_lso_rd_dma_workaround_bit(tp);
tw32(TG3_LSO_RD_DMA_CRPTEN_CTRL, val);
- tg3_flag_set(tp, 5719_RDMA_BUG);
+ tg3_flag_set(tp, 5719_5720_RDMA_BUG);
}
}
TG3_STAT_ADD32(&sp->tx_ucast_packets, MAC_TX_STATS_UCAST);
TG3_STAT_ADD32(&sp->tx_mcast_packets, MAC_TX_STATS_MCAST);
TG3_STAT_ADD32(&sp->tx_bcast_packets, MAC_TX_STATS_BCAST);
- if (unlikely(tg3_flag(tp, 5719_RDMA_BUG) &&
+ if (unlikely(tg3_flag(tp, 5719_5720_RDMA_BUG) &&
(sp->tx_ucast_packets.low + sp->tx_mcast_packets.low +
sp->tx_bcast_packets.low) > TG3_NUM_RDMA_CHANNELS)) {
u32 val;
val = tr32(TG3_LSO_RD_DMA_CRPTEN_CTRL);
- val &= ~TG3_LSO_RD_DMA_TX_LENGTH_WA;
+ val &= ~tg3_lso_rd_dma_workaround_bit(tp);
tw32(TG3_LSO_RD_DMA_CRPTEN_CTRL, val);
- tg3_flag_clear(tp, 5719_RDMA_BUG);
+ tg3_flag_clear(tp, 5719_5720_RDMA_BUG);
}
TG3_STAT_ADD32(&sp->rx_octets, MAC_RX_STATS_OCTETS);
#define TG3_LSO_RD_DMA_CRPTEN_CTRL 0x00004910
#define TG3_LSO_RD_DMA_CRPTEN_CTRL_BLEN_BD_4K 0x00030000
#define TG3_LSO_RD_DMA_CRPTEN_CTRL_BLEN_LSO_4K 0x000c0000
-#define TG3_LSO_RD_DMA_TX_LENGTH_WA 0x02000000
+#define TG3_LSO_RD_DMA_TX_LENGTH_WA_5719 0x02000000
+#define TG3_LSO_RD_DMA_TX_LENGTH_WA_5720 0x00200000
/* 0x4914 --> 0x4be0 unused */
#define TG3_NUM_RDMA_CHANNELS 4
TG3_FLAG_APE_HAS_NCSI,
TG3_FLAG_TX_TSTAMP_EN,
TG3_FLAG_4K_FIFO_LIMIT,
- TG3_FLAG_5719_RDMA_BUG,
+ TG3_FLAG_5719_5720_RDMA_BUG,
TG3_FLAG_RESET_TASK_PENDING,
TG3_FLAG_PTP_CAPABLE,
TG3_FLAG_5705_PLUS,
status = macb_readl(bp, TSR);
macb_writel(bp, TSR, status);
- macb_writel(bp, ISR, MACB_BIT(TCOMP));
+ if (bp->caps & MACB_CAPS_ISR_CLEAR_ON_WRITE)
+ macb_writel(bp, ISR, MACB_BIT(TCOMP));
netdev_vdbg(bp->dev, "macb_tx_interrupt status = 0x%03lx\n",
(unsigned long)status);
* now.
*/
macb_writel(bp, IDR, MACB_RX_INT_FLAGS);
- macb_writel(bp, ISR, MACB_BIT(RCOMP));
+ if (bp->caps & MACB_CAPS_ISR_CLEAR_ON_WRITE)
+ macb_writel(bp, ISR, MACB_BIT(RCOMP));
if (napi_schedule_prep(&bp->napi)) {
netdev_vdbg(bp->dev, "scheduling RX softirq\n");
}
}
+/*
+ * Configure peripheral capacities according to integration options used
+ */
+static void macb_configure_caps(struct macb *bp)
+{
+ if (macb_is_gem(bp)) {
+ if (GEM_BF(IRQCOR, gem_readl(bp, DCFG1)) == 0)
+ bp->caps |= MACB_CAPS_ISR_CLEAR_ON_WRITE;
+ }
+}
+
static void macb_init_hw(struct macb *bp)
{
u32 config;
bp->duplex = DUPLEX_HALF;
macb_configure_dma(bp);
+ macb_configure_caps(bp);
/* Initialize TX and RX buffers */
macb_writel(bp, RBQP, bp->rx_ring_dma);
#define MACB_REV_SIZE 16
/* Bitfields in DCFG1. */
+#define GEM_IRQCOR_OFFSET 23
+#define GEM_IRQCOR_SIZE 1
#define GEM_DBWDEF_OFFSET 25
#define GEM_DBWDEF_SIZE 3
#define MACB_MAN_READ 2
#define MACB_MAN_CODE 2
+/* Capability mask bits */
+#define MACB_CAPS_ISR_CLEAR_ON_WRITE 0x1
+
/* Bit manipulation macros */
#define MACB_BIT(name) \
(1 << MACB_##name##_OFFSET)
unsigned int speed;
unsigned int duplex;
+ u32 caps;
+
phy_interface_t phy_interface;
/* AT91RM9200 transmit */
u8 ipv6;
u8 vtm;
u8 pkt_type;
+ u8 ip_frag;
};
struct be_rx_obj {
resource_error = lancer_provisioning_error(adapter);
if (resource_error)
- return -1;
+ return -EAGAIN;
status = lancer_wait_ready(adapter);
if (!status) {
* when PF provisions resources.
*/
resource_error = lancer_provisioning_error(adapter);
- if (status == -1 && !resource_error)
- adapter->eeh_error = true;
+ if (resource_error)
+ status = -EAGAIN;
return status;
}
for (i = 0; i < desc_count; i++) {
desc->desc_len = desc->desc_len ? : RESOURCE_DESC_SIZE;
if (((void *)desc + desc->desc_len) >
- (void *)(buf + max_buf_size)) {
- desc = NULL;
- break;
- }
+ (void *)(buf + max_buf_size))
+ return NULL;
if (desc->desc_type == NIC_RESOURCE_DESC_TYPE_V0 ||
desc->desc_type == NIC_RESOURCE_DESC_TYPE_V1)
- break;
+ return desc;
desc = (void *)desc + desc->desc_len;
}
- if (!desc || i == MAX_RESOURCE_DESC)
- return NULL;
-
- return desc;
+ return NULL;
}
/* Uses Mbox */
u8 ip_version; /* dword 1 */
u8 macdst[6]; /* dword 1 */
u8 vtp; /* dword 1 */
- u8 rsvd0; /* dword 1 */
+ u8 ip_frag; /* dword 1 */
u8 fragndx[10]; /* dword 1 */
u8 ct[2]; /* dword 1 */
u8 sw; /* dword 1 */
if (unlikely(!skb))
return skb;
- if (vlan_tx_tag_present(skb)) {
+ if (vlan_tx_tag_present(skb))
vlan_tag = be_get_tx_vlan_tag(adapter, skb);
- skb = __vlan_put_tag(skb, htons(ETH_P_8021Q), vlan_tag);
- if (skb)
- skb->vlan_tci = 0;
- }
-
- if (qnq_async_evt_rcvd(adapter) && adapter->pvid) {
- if (!vlan_tag)
- vlan_tag = adapter->pvid;
- if (skip_hw_vlan)
- *skip_hw_vlan = true;
- }
+ else if (qnq_async_evt_rcvd(adapter) && adapter->pvid)
+ vlan_tag = adapter->pvid;
if (vlan_tag) {
skb = __vlan_put_tag(skb, htons(ETH_P_8021Q), vlan_tag);
if (unlikely(!skb))
return skb;
-
skb->vlan_tci = 0;
+ if (skip_hw_vlan)
+ *skip_hw_vlan = true;
}
/* Insert the outer VLAN, if any */
compl);
}
rxcp->port = AMAP_GET_BITS(struct amap_eth_rx_compl_v0, port, compl);
+ rxcp->ip_frag = AMAP_GET_BITS(struct amap_eth_rx_compl_v0,
+ ip_frag, compl);
}
static struct be_rx_compl_info *be_rx_compl_get(struct be_rx_obj *rxo)
else
be_parse_rx_compl_v0(compl, rxcp);
+ if (rxcp->ip_frag)
+ rxcp->l4_csum = 0;
+
if (rxcp->vlanf) {
/* vlanf could be wrongly set in some cards.
* ignore if vtm is not set */
static inline bool do_gro(struct be_rx_compl_info *rxcp)
{
- return (rxcp->tcpf && !rxcp->err) ? true : false;
+ return (rxcp->tcpf && !rxcp->err && rxcp->l4_csum) ? true : false;
}
static int be_process_rx(struct be_rx_obj *rxo, struct napi_struct *napi,
static int lancer_recover_func(struct be_adapter *adapter)
{
+ struct device *dev = &adapter->pdev->dev;
int status;
status = lancer_test_and_set_rdy_state(adapter);
be_clear(adapter);
- adapter->hw_error = false;
- adapter->fw_timeout = false;
+ be_clear_all_error(adapter);
status = be_setup(adapter);
if (status)
goto err;
}
- dev_err(&adapter->pdev->dev,
- "Adapter SLIPORT recovery succeeded\n");
+ dev_err(dev, "Error recovery successful\n");
return 0;
err:
- if (adapter->eeh_error)
- dev_err(&adapter->pdev->dev,
- "Adapter SLIPORT recovery failed\n");
+ if (status == -EAGAIN)
+ dev_err(dev, "Waiting for resource provisioning\n");
+ else
+ dev_err(dev, "Error recovery failed\n");
return status;
}
{
struct be_adapter *adapter =
container_of(work, struct be_adapter, func_recovery_work.work);
- int status;
+ int status = 0;
be_detect_error(adapter);
if (adapter->hw_error && lancer_chip(adapter)) {
- if (adapter->eeh_error)
- goto out;
-
rtnl_lock();
netif_device_detach(adapter->netdev);
rtnl_unlock();
status = lancer_recover_func(adapter);
-
if (!status)
netif_device_attach(adapter->netdev);
}
-out:
- schedule_delayed_work(&adapter->func_recovery_work,
- msecs_to_jiffies(1000));
+ /* In Lancer, for all errors other than provisioning error (-EAGAIN),
+ * no need to attempt further recovery.
+ */
+ if (!status || status == -EAGAIN)
+ schedule_delayed_work(&adapter->func_recovery_work,
+ msecs_to_jiffies(1000));
}
static void be_worker(struct work_struct *work)
dev_err(&adapter->pdev->dev, "EEH error detected\n");
- adapter->eeh_error = true;
-
- cancel_delayed_work_sync(&adapter->func_recovery_work);
+ if (!adapter->eeh_error) {
+ adapter->eeh_error = true;
- rtnl_lock();
- netif_device_detach(netdev);
- rtnl_unlock();
+ cancel_delayed_work_sync(&adapter->func_recovery_work);
- if (netif_running(netdev)) {
rtnl_lock();
- be_close(netdev);
+ netif_device_detach(netdev);
+ if (netif_running(netdev))
+ be_close(netdev);
rtnl_unlock();
+
+ be_clear(adapter);
}
- be_clear(adapter);
if (state == pci_channel_io_perm_failure)
return PCI_ERS_RESULT_DISCONNECT;
int status;
dev_info(&adapter->pdev->dev, "EEH reset\n");
- be_clear_all_error(adapter);
status = pci_enable_device(pdev);
if (status)
return PCI_ERS_RESULT_DISCONNECT;
pci_cleanup_aer_uncorrect_error_status(pdev);
+ be_clear_all_error(adapter);
return PCI_ERS_RESULT_RECOVERED;
}
.driver_data = FEC_QUIRK_ENET_MAC | FEC_QUIRK_HAS_GBIT |
FEC_QUIRK_HAS_BUFDESC_EX | FEC_QUIRK_HAS_CSUM,
}, {
- .name = "mvf-fec",
+ .name = "mvf600-fec",
.driver_data = FEC_QUIRK_ENET_MAC,
}, {
/* sentinel */
IMX27_FEC, /* runs on i.mx27/35/51 */
IMX28_FEC,
IMX6Q_FEC,
- MVF_FEC,
+ MVF600_FEC,
};
static const struct of_device_id fec_dt_ids[] = {
{ .compatible = "fsl,imx27-fec", .data = &fec_devtype[IMX27_FEC], },
{ .compatible = "fsl,imx28-fec", .data = &fec_devtype[IMX28_FEC], },
{ .compatible = "fsl,imx6q-fec", .data = &fec_devtype[IMX6Q_FEC], },
- { .compatible = "fsl,mvf-fec", .data = &fec_devtype[MVF_FEC], },
+ { .compatible = "fsl,mvf600-fec", .data = &fec_devtype[MVF600_FEC], },
{ /* sentinel */ }
};
MODULE_DEVICE_TABLE(of, fec_dt_ids);
netif_device_detach(ndev);
napi_disable(&fep->napi);
netif_stop_queue(ndev);
- netif_tx_lock(ndev);
+ netif_tx_lock_bh(ndev);
}
/* Whack a reset. We should wait for this. */
writel(FEC_DEFAULT_IMASK, fep->hwp + FEC_IMASK);
if (netif_running(ndev)) {
- netif_device_attach(ndev);
- napi_enable(&fep->napi);
+ netif_tx_unlock_bh(ndev);
netif_wake_queue(ndev);
- netif_tx_unlock(ndev);
+ napi_enable(&fep->napi);
+ netif_device_attach(ndev);
}
}
iap = &tmpaddr[0];
}
+ /*
+ * 5) random mac address
+ */
+ if (!is_valid_ether_addr(iap)) {
+ /* Report it and use a random ethernet address instead */
+ netdev_err(ndev, "Invalid MAC address: %pM\n", iap);
+ eth_hw_addr_random(ndev);
+ netdev_info(ndev, "Using random MAC address: %pM\n",
+ ndev->dev_addr);
+ return;
+ }
+
memcpy(ndev->dev_addr, iap, ETH_ALEN);
/* Adjust MAC if using macaddr */
return 0;
no_clock:
+ iounmap(etsects->regs);
no_ioremap:
release_resource(etsects->rsrc);
no_resource:
/* TFD data structure masks. */
/* TFDList, TFC */
-#define IPG_TFC_RSVD_MASK 0x0000FFFF9FFFFFFF
-#define IPG_TFC_FRAMEID 0x000000000000FFFF
-#define IPG_TFC_WORDALIGN 0x0000000000030000
-#define IPG_TFC_WORDALIGNTODWORD 0x0000000000000000
-#define IPG_TFC_WORDALIGNTOWORD 0x0000000000020000
-#define IPG_TFC_WORDALIGNDISABLED 0x0000000000030000
-#define IPG_TFC_TCPCHECKSUMENABLE 0x0000000000040000
-#define IPG_TFC_UDPCHECKSUMENABLE 0x0000000000080000
-#define IPG_TFC_IPCHECKSUMENABLE 0x0000000000100000
-#define IPG_TFC_FCSAPPENDDISABLE 0x0000000000200000
-#define IPG_TFC_TXINDICATE 0x0000000000400000
-#define IPG_TFC_TXDMAINDICATE 0x0000000000800000
-#define IPG_TFC_FRAGCOUNT 0x000000000F000000
-#define IPG_TFC_VLANTAGINSERT 0x0000000010000000
-#define IPG_TFC_TFDDONE 0x0000000080000000
-#define IPG_TFC_VID 0x00000FFF00000000
-#define IPG_TFC_CFI 0x0000100000000000
-#define IPG_TFC_USERPRIORITY 0x0000E00000000000
+#define IPG_TFC_RSVD_MASK 0x0000FFFF9FFFFFFFULL
+#define IPG_TFC_FRAMEID 0x000000000000FFFFULL
+#define IPG_TFC_WORDALIGN 0x0000000000030000ULL
+#define IPG_TFC_WORDALIGNTODWORD 0x0000000000000000ULL
+#define IPG_TFC_WORDALIGNTOWORD 0x0000000000020000ULL
+#define IPG_TFC_WORDALIGNDISABLED 0x0000000000030000ULL
+#define IPG_TFC_TCPCHECKSUMENABLE 0x0000000000040000ULL
+#define IPG_TFC_UDPCHECKSUMENABLE 0x0000000000080000ULL
+#define IPG_TFC_IPCHECKSUMENABLE 0x0000000000100000ULL
+#define IPG_TFC_FCSAPPENDDISABLE 0x0000000000200000ULL
+#define IPG_TFC_TXINDICATE 0x0000000000400000ULL
+#define IPG_TFC_TXDMAINDICATE 0x0000000000800000ULL
+#define IPG_TFC_FRAGCOUNT 0x000000000F000000ULL
+#define IPG_TFC_VLANTAGINSERT 0x0000000010000000ULL
+#define IPG_TFC_TFDDONE 0x0000000080000000ULL
+#define IPG_TFC_VID 0x00000FFF00000000ULL
+#define IPG_TFC_CFI 0x0000100000000000ULL
+#define IPG_TFC_USERPRIORITY 0x0000E00000000000ULL
/* TFDList, FragInfo */
-#define IPG_TFI_RSVD_MASK 0xFFFF00FFFFFFFFFF
-#define IPG_TFI_FRAGADDR 0x000000FFFFFFFFFF
-#define IPG_TFI_FRAGLEN 0xFFFF000000000000LL
+#define IPG_TFI_RSVD_MASK 0xFFFF00FFFFFFFFFFULL
+#define IPG_TFI_FRAGADDR 0x000000FFFFFFFFFFULL
+#define IPG_TFI_FRAGLEN 0xFFFF000000000000ULL
/* RFD data structure masks. */
/* RFDList, RFS */
-#define IPG_RFS_RSVD_MASK 0x0000FFFFFFFFFFFF
-#define IPG_RFS_RXFRAMELEN 0x000000000000FFFF
-#define IPG_RFS_RXFIFOOVERRUN 0x0000000000010000
-#define IPG_RFS_RXRUNTFRAME 0x0000000000020000
-#define IPG_RFS_RXALIGNMENTERROR 0x0000000000040000
-#define IPG_RFS_RXFCSERROR 0x0000000000080000
-#define IPG_RFS_RXOVERSIZEDFRAME 0x0000000000100000
-#define IPG_RFS_RXLENGTHERROR 0x0000000000200000
-#define IPG_RFS_VLANDETECTED 0x0000000000400000
-#define IPG_RFS_TCPDETECTED 0x0000000000800000
-#define IPG_RFS_TCPERROR 0x0000000001000000
-#define IPG_RFS_UDPDETECTED 0x0000000002000000
-#define IPG_RFS_UDPERROR 0x0000000004000000
-#define IPG_RFS_IPDETECTED 0x0000000008000000
-#define IPG_RFS_IPERROR 0x0000000010000000
-#define IPG_RFS_FRAMESTART 0x0000000020000000
-#define IPG_RFS_FRAMEEND 0x0000000040000000
-#define IPG_RFS_RFDDONE 0x0000000080000000
-#define IPG_RFS_TCI 0x0000FFFF00000000
+#define IPG_RFS_RSVD_MASK 0x0000FFFFFFFFFFFFULL
+#define IPG_RFS_RXFRAMELEN 0x000000000000FFFFULL
+#define IPG_RFS_RXFIFOOVERRUN 0x0000000000010000ULL
+#define IPG_RFS_RXRUNTFRAME 0x0000000000020000ULL
+#define IPG_RFS_RXALIGNMENTERROR 0x0000000000040000ULL
+#define IPG_RFS_RXFCSERROR 0x0000000000080000ULL
+#define IPG_RFS_RXOVERSIZEDFRAME 0x0000000000100000ULL
+#define IPG_RFS_RXLENGTHERROR 0x0000000000200000ULL
+#define IPG_RFS_VLANDETECTED 0x0000000000400000ULL
+#define IPG_RFS_TCPDETECTED 0x0000000000800000ULL
+#define IPG_RFS_TCPERROR 0x0000000001000000ULL
+#define IPG_RFS_UDPDETECTED 0x0000000002000000ULL
+#define IPG_RFS_UDPERROR 0x0000000004000000ULL
+#define IPG_RFS_IPDETECTED 0x0000000008000000ULL
+#define IPG_RFS_IPERROR 0x0000000010000000ULL
+#define IPG_RFS_FRAMESTART 0x0000000020000000ULL
+#define IPG_RFS_FRAMEEND 0x0000000040000000ULL
+#define IPG_RFS_RFDDONE 0x0000000080000000ULL
+#define IPG_RFS_TCI 0x0000FFFF00000000ULL
/* RFDList, FragInfo */
-#define IPG_RFI_RSVD_MASK 0xFFFF00FFFFFFFFFF
-#define IPG_RFI_FRAGADDR 0x000000FFFFFFFFFF
-#define IPG_RFI_FRAGLEN 0xFFFF000000000000LL
+#define IPG_RFI_RSVD_MASK 0xFFFF00FFFFFFFFFFULL
+#define IPG_RFI_FRAGADDR 0x000000FFFFFFFFFFULL
+#define IPG_RFI_FRAGLEN 0xFFFF000000000000ULL
/* I/O Register masks. */
struct netdev_queue *nq = netdev_get_tx_queue(mp->dev, txq->index);
int reclaimed;
- __netif_tx_lock(nq, smp_processor_id());
+ __netif_tx_lock_bh(nq);
reclaimed = 0;
while (reclaimed < budget && txq->tx_desc_count > 0) {
dev_kfree_skb(skb);
}
- __netif_tx_unlock(nq);
+ __netif_tx_unlock_bh(nq);
if (reclaimed < budget)
mp->work_tx &= ~(1 << txq->index);
INIT_WORK(&mp->tx_timeout_task, tx_timeout_task);
- netif_napi_add(dev, &mp->napi, mv643xx_eth_poll, 128);
+ netif_napi_add(dev, &mp->napi, mv643xx_eth_poll, NAPI_POLL_WEIGHT);
init_timer(&mp->rx_oom);
mp->rx_oom.data = (unsigned long)mp;
* FLR process. The only non-zero result in the RESET command
* is MLX4_DELAY_RESET_SLAVE*/
if ((MLX4_COMM_CMD_RESET == cmd)) {
- mlx4_warn(dev, "Got slave FLRed from Communication"
- " channel (ret:0x%x)\n", ret_from_pending);
err = MLX4_DELAY_RESET_SLAVE;
} else {
mlx4_warn(dev, "Communication channel timed out\n");
priv->last_moder_time[ring] = moder_time;
cq = &priv->rx_cq[ring];
cq->moder_time = moder_time;
+ cq->moder_cnt = priv->rx_frames;
err = mlx4_en_set_cq_moder(priv, cq);
if (err)
en_err(priv, "Failed modifying moderation for cq:%d\n",
struct mlx4_en_priv *priv;
int i;
int err;
+ u64 mac_u64;
dev = alloc_etherdev_mqs(sizeof(struct mlx4_en_priv),
MAX_TX_RINGS, MAX_RX_RINGS);
dev->addr_len = ETH_ALEN;
mlx4_en_u64_to_mac(dev->dev_addr, mdev->dev->caps.def_mac[priv->port]);
if (!is_valid_ether_addr(dev->dev_addr)) {
- en_err(priv, "Port: %d, invalid mac burned: %pM, quiting\n",
- priv->port, dev->dev_addr);
- err = -EINVAL;
- goto out;
+ if (mlx4_is_slave(priv->mdev->dev)) {
+ eth_hw_addr_random(dev);
+ en_warn(priv, "Assigned random MAC address %pM\n", dev->dev_addr);
+ mac_u64 = mlx4_en_mac_to_u64(dev->dev_addr);
+ mdev->dev->caps.def_mac[priv->port] = mac_u64;
+ } else {
+ en_err(priv, "Port: %d, invalid mac burned: %pM, quiting\n",
+ priv->port, dev->dev_addr);
+ err = -EINVAL;
+ goto out;
+ }
}
memcpy(priv->prev_mac, dev->dev_addr, sizeof(priv->prev_mac));
MLX4_CMD_NATIVE);
if (!err && dev->caps.function != slave) {
- /* set slave default_mac address */
- MLX4_GET(def_mac, outbox->buf, QUERY_PORT_MAC_OFFSET);
- def_mac += slave << 8;
/* if config MAC in DB use it */
if (priv->mfunc.master.vf_oper[slave].vport[vhcr->in_modifier].state.mac)
def_mac = priv->mfunc.master.vf_oper[slave].vport[vhcr->in_modifier].state.mac;
+ else {
+ /* set slave default_mac address */
+ MLX4_GET(def_mac, outbox->buf, QUERY_PORT_MAC_OFFSET);
+ def_mac += slave << 8;
+ priv->mfunc.master.vf_admin[slave].vport[vhcr->in_modifier].mac = def_mac;
+ }
+
MLX4_PUT(outbox->buf, def_mac, QUERY_PORT_MAC_OFFSET);
/* get port type - currently only eth is enabled */
{
struct mlx4_priv *priv = mlx4_priv(dev);
u64 dma = (u64) priv->mfunc.vhcr_dma;
- int num_of_reset_retries = NUM_OF_RESET_RETRIES;
int ret_from_reset = 0;
u32 slave_read;
u32 cmd_channel_ver;
* NUM_OF_RESET_RETRIES times before leaving.*/
if (ret_from_reset) {
if (MLX4_DELAY_RESET_SLAVE == ret_from_reset) {
- msleep(SLEEP_TIME_IN_RESET);
- while (ret_from_reset && num_of_reset_retries) {
- mlx4_warn(dev, "slave is currently in the"
- "middle of FLR. retrying..."
- "(try num:%d)\n",
- (NUM_OF_RESET_RETRIES -
- num_of_reset_retries + 1));
- ret_from_reset =
- mlx4_comm_cmd(dev, MLX4_COMM_CMD_RESET,
- 0, MLX4_COMM_TIME);
- num_of_reset_retries = num_of_reset_retries - 1;
- }
+ mlx4_warn(dev, "slave is currently in the "
+ "middle of FLR. Deferring probe.\n");
+ mutex_unlock(&priv->cmd.slave_cmd_mutex);
+ return -EPROBE_DEFER;
} else
goto err;
}
} else {
err = mlx4_init_slave(dev);
if (err) {
- mlx4_err(dev, "Failed to initialize slave\n");
+ if (err != -EPROBE_DEFER)
+ mlx4_err(dev, "Failed to initialize slave\n");
return err;
}
#define QLCNIC_FW_HANG 0x4000
#define QLCNIC_FW_LRO_MSS_CAP 0x8000
#define QLCNIC_TX_INTR_SHARED 0x10000
+#define QLCNIC_APP_CHANGED_FLAGS 0x20000
#define QLCNIC_IS_MSI_FAMILY(adapter) \
((adapter)->flags & (QLCNIC_MSI_ENABLED | QLCNIC_MSIX_ENABLED))
+#define QLCNIC_IS_TSO_CAPABLE(adapter) \
+ ((adapter)->ahw->capabilities & QLCNIC_FW_CAPABILITY_TSO)
#define QLCNIC_DEF_NUM_STS_DESC_RINGS 4
#define QLCNIC_MSIX_TBL_SPACE 8192
spinlock_t rx_mac_learn_lock;
u32 file_prd_off; /*File fw product offset*/
u32 fw_version;
+ u32 offload_flags;
const struct firmware *fw;
};
int qlcnic_83xx_configure_opmode(struct qlcnic_adapter *adapter);
int qlcnic_read_mac_addr(struct qlcnic_adapter *);
int qlcnic_setup_netdev(struct qlcnic_adapter *, struct net_device *, int);
+void qlcnic_set_netdev_features(struct qlcnic_adapter *,
+ struct qlcnic_esw_func_cfg *);
void qlcnic_sriov_vf_schedule_multi(struct net_device *);
void qlcnic_vf_add_mc_list(struct net_device *, u16);
clear_bit(__QLCNIC_RESETTING, &adapter->state);
dev_err(&adapter->pdev->dev, "%s:\n", __func__);
- adapter->netdev->trans_start = jiffies;
-
return 0;
}
return rc;
}
+static netdev_features_t qlcnic_process_flags(struct qlcnic_adapter *adapter,
+ netdev_features_t features)
+{
+ u32 offload_flags = adapter->offload_flags;
+
+ if (offload_flags & BIT_0) {
+ features |= NETIF_F_RXCSUM | NETIF_F_IP_CSUM |
+ NETIF_F_IPV6_CSUM;
+ adapter->rx_csum = 1;
+ if (QLCNIC_IS_TSO_CAPABLE(adapter)) {
+ if (!(offload_flags & BIT_1))
+ features &= ~NETIF_F_TSO;
+ else
+ features |= NETIF_F_TSO;
+
+ if (!(offload_flags & BIT_2))
+ features &= ~NETIF_F_TSO6;
+ else
+ features |= NETIF_F_TSO6;
+ }
+ } else {
+ features &= ~(NETIF_F_RXCSUM |
+ NETIF_F_IP_CSUM |
+ NETIF_F_IPV6_CSUM);
+
+ if (QLCNIC_IS_TSO_CAPABLE(adapter))
+ features &= ~(NETIF_F_TSO | NETIF_F_TSO6);
+ adapter->rx_csum = 0;
+ }
+
+ return features;
+}
netdev_features_t qlcnic_fix_features(struct net_device *netdev,
netdev_features_t features)
{
struct qlcnic_adapter *adapter = netdev_priv(netdev);
+ netdev_features_t changed;
- if ((adapter->flags & QLCNIC_ESWITCH_ENABLED) &&
- qlcnic_82xx_check(adapter)) {
- netdev_features_t changed = features ^ netdev->features;
- features ^= changed & (NETIF_F_ALL_CSUM | NETIF_F_RXCSUM);
+ if (qlcnic_82xx_check(adapter) &&
+ (adapter->flags & QLCNIC_ESWITCH_ENABLED)) {
+ if (adapter->flags & QLCNIC_APP_CHANGED_FLAGS) {
+ features = qlcnic_process_flags(adapter, features);
+ } else {
+ changed = features ^ netdev->features;
+ features ^= changed & (NETIF_F_RXCSUM |
+ NETIF_F_IP_CSUM |
+ NETIF_F_IPV6_CSUM |
+ NETIF_F_TSO |
+ NETIF_F_TSO6);
+ }
}
if (!(features & NETIF_F_RXCSUM))
static void qlcnic_free_lb_filters_mem(struct qlcnic_adapter *adapter);
static void qlcnic_dev_set_npar_ready(struct qlcnic_adapter *);
static int qlcnicvf_start_firmware(struct qlcnic_adapter *);
-static void qlcnic_set_netdev_features(struct qlcnic_adapter *,
- struct qlcnic_esw_func_cfg *);
static int qlcnic_vlan_rx_add(struct net_device *, __be16, u16);
static int qlcnic_vlan_rx_del(struct net_device *, __be16, u16);
-#define QLCNIC_IS_TSO_CAPABLE(adapter) \
- ((adapter)->ahw->capabilities & QLCNIC_FW_CAPABILITY_TSO)
-
static u32 qlcnic_vlan_tx_check(struct qlcnic_adapter *adapter)
{
struct qlcnic_hardware_context *ahw = adapter->ahw;
if (!esw_cfg->promisc_mode)
adapter->flags |= QLCNIC_PROMISC_DISABLED;
-
- qlcnic_set_netdev_features(adapter, esw_cfg);
}
int qlcnic_set_eswitch_port_config(struct qlcnic_adapter *adapter)
return -EIO;
qlcnic_set_vlan_config(adapter, &esw_cfg);
qlcnic_set_eswitch_port_features(adapter, &esw_cfg);
+ qlcnic_set_netdev_features(adapter, &esw_cfg);
return 0;
}
-static void
-qlcnic_set_netdev_features(struct qlcnic_adapter *adapter,
- struct qlcnic_esw_func_cfg *esw_cfg)
+void qlcnic_set_netdev_features(struct qlcnic_adapter *adapter,
+ struct qlcnic_esw_func_cfg *esw_cfg)
{
struct net_device *netdev = adapter->netdev;
- unsigned long features, vlan_features;
if (qlcnic_83xx_check(adapter))
return;
- features = (NETIF_F_SG | NETIF_F_IP_CSUM | NETIF_F_RXCSUM |
- NETIF_F_IPV6_CSUM | NETIF_F_GRO);
- vlan_features = (NETIF_F_SG | NETIF_F_IP_CSUM |
- NETIF_F_IPV6_CSUM);
-
- if (QLCNIC_IS_TSO_CAPABLE(adapter)) {
- features |= (NETIF_F_TSO | NETIF_F_TSO6);
- vlan_features |= (NETIF_F_TSO | NETIF_F_TSO6);
- }
-
- if (netdev->features & NETIF_F_LRO)
- features |= NETIF_F_LRO;
-
- if (esw_cfg->offload_flags & BIT_0) {
- netdev->features |= features;
- adapter->rx_csum = 1;
- if (!(esw_cfg->offload_flags & BIT_1)) {
- netdev->features &= ~NETIF_F_TSO;
- features &= ~NETIF_F_TSO;
- }
- if (!(esw_cfg->offload_flags & BIT_2)) {
- netdev->features &= ~NETIF_F_TSO6;
- features &= ~NETIF_F_TSO6;
- }
- } else {
- netdev->features &= ~features;
- features &= ~features;
- adapter->rx_csum = 0;
- }
-
- netdev->vlan_features = (features & vlan_features);
+ adapter->offload_flags = esw_cfg->offload_flags;
+ adapter->flags |= QLCNIC_APP_CHANGED_FLAGS;
+ netdev_update_features(netdev);
+ adapter->flags &= ~QLCNIC_APP_CHANGED_FLAGS;
}
static int
pci_enable_pcie_error_reporting(pdev);
ahw = kzalloc(sizeof(struct qlcnic_hardware_context), GFP_KERNEL);
- if (!ahw)
+ if (!ahw) {
+ err = -ENOMEM;
goto err_out_free_res;
+ }
switch (ent->device) {
case PCI_DEVICE_ID_QLOGIC_QLE824X:
adapter->qlcnic_wq = create_singlethread_workqueue("qlcnic");
if (adapter->qlcnic_wq == NULL) {
+ err = -ENOMEM;
dev_err(&pdev->dev, "Failed to create workqueue\n");
goto err_out_free_netdev;
}
goto err_out_disable_msi;
}
+ err = qlcnic_get_act_pci_func(adapter);
+ if (err)
+ goto err_out_disable_mbx_intr;
+
err = qlcnic_setup_netdev(adapter, netdev, pci_using_dac);
if (err)
goto err_out_disable_mbx_intr;
break;
}
- if (qlcnic_get_act_pci_func(adapter))
- goto err_out_disable_mbx_intr;
-
if (adapter->drv_mac_learn)
qlcnic_alloc_lb_filters_mem(adapter);
if (adapter->need_fw_reset)
goto detach;
- if (adapter->ahw->reset_context && qlcnic_auto_fw_reset) {
+ if (adapter->ahw->reset_context && qlcnic_auto_fw_reset)
qlcnic_reset_hw_context(adapter);
- adapter->netdev->trans_start = jiffies;
- }
return 0;
}
if (!qlcnic_sriov_vf_reinit_driver(adapter)) {
qlcnic_sriov_vf_attach(adapter);
- adapter->netdev->trans_start = jiffies;
adapter->tx_timeo_cnt = 0;
adapter->reset_ctx_cnt = 0;
adapter->fw_fail_cnt = 0;
switch (esw_cfg[i].op_mode) {
case QLCNIC_PORT_DEFAULTS:
qlcnic_set_eswitch_port_features(adapter, &esw_cfg[i]);
+ rtnl_lock();
+ qlcnic_set_netdev_features(adapter, &esw_cfg[i]);
+ rtnl_unlock();
break;
case QLCNIC_ADD_VLAN:
qlcnic_set_vlan_config(adapter, &esw_cfg[i]);
dev_err(&pdev->dev, "net device registration failed.\n");
ql_release_all(pdev);
pci_disable_device(pdev);
+ free_netdev(ndev);
return err;
}
/* Start up the timer to trigger EEH if
cp->dev->stats.tx_dropped++;
}
}
+ netdev_reset_queue(cp->dev);
memset(cp->rx_ring, 0, sizeof(struct cp_desc) * CP_RX_RING_SIZE);
memset(cp->tx_ring, 0, sizeof(struct cp_desc) * CP_TX_RING_SIZE);
return -EIO;
}
-static inline void rtl8169_tso_csum(struct rtl8169_private *tp,
+static bool rtl_skb_pad(struct sk_buff *skb)
+{
+ if (skb_padto(skb, ETH_ZLEN))
+ return false;
+ skb_put(skb, ETH_ZLEN - skb->len);
+ return true;
+}
+
+static bool rtl_test_hw_pad_bug(struct rtl8169_private *tp, struct sk_buff *skb)
+{
+ return skb->len < ETH_ZLEN && tp->mac_version == RTL_GIGA_MAC_VER_34;
+}
+
+static inline bool rtl8169_tso_csum(struct rtl8169_private *tp,
struct sk_buff *skb, u32 *opts)
{
const struct rtl_tx_desc_info *info = tx_desc_info + tp->txd_version;
} else if (skb->ip_summed == CHECKSUM_PARTIAL) {
const struct iphdr *ip = ip_hdr(skb);
+ if (unlikely(rtl_test_hw_pad_bug(tp, skb)))
+ return skb_checksum_help(skb) == 0 && rtl_skb_pad(skb);
+
if (ip->protocol == IPPROTO_TCP)
opts[offset] |= info->checksum.tcp;
else if (ip->protocol == IPPROTO_UDP)
opts[offset] |= info->checksum.udp;
else
WARN_ON_ONCE(1);
+ } else {
+ if (unlikely(rtl_test_hw_pad_bug(tp, skb)))
+ return rtl_skb_pad(skb);
}
+ return true;
}
static netdev_tx_t rtl8169_start_xmit(struct sk_buff *skb,
goto err_stop_0;
}
- /* 8168evl does not automatically pad to minimum length. */
- if (unlikely(tp->mac_version == RTL_GIGA_MAC_VER_34 &&
- skb->len < ETH_ZLEN)) {
- if (skb_padto(skb, ETH_ZLEN))
- goto err_update_stats;
- skb_put(skb, ETH_ZLEN - skb->len);
- }
-
if (unlikely(le32_to_cpu(txd->opts1) & DescOwn))
goto err_stop_0;
+ opts[1] = cpu_to_le32(rtl8169_tx_vlan_tag(skb));
+ opts[0] = DescOwn;
+
+ if (!rtl8169_tso_csum(tp, skb, opts))
+ goto err_update_stats;
+
len = skb_headlen(skb);
mapping = dma_map_single(d, skb->data, len, DMA_TO_DEVICE);
if (unlikely(dma_mapping_error(d, mapping))) {
tp->tx_skb[entry].len = len;
txd->addr = cpu_to_le64(mapping);
- opts[1] = cpu_to_le32(rtl8169_tx_vlan_tag(skb));
- opts[0] = DescOwn;
-
- rtl8169_tso_csum(tp, skb, opts);
-
frags = rtl8169_xmit_frags(tp, skb, opts);
if (frags < 0)
goto err_dma_1;
EFX_MAX_FRAME_LEN(efx->net_dev->mtu) +
efx->type->rx_buffer_padding);
rx_buf_len = (sizeof(struct efx_rx_page_state) +
- EFX_PAGE_IP_ALIGN + efx->rx_dma_len);
+ NET_IP_ALIGN + efx->rx_dma_len);
if (rx_buf_len <= PAGE_SIZE) {
efx->rx_scatter = false;
efx->rx_buffer_order = 0;
} else if (efx->type->can_rx_scatter) {
+ BUILD_BUG_ON(EFX_RX_USR_BUF_SIZE % L1_CACHE_BYTES);
BUILD_BUG_ON(sizeof(struct efx_rx_page_state) +
- EFX_PAGE_IP_ALIGN + EFX_RX_USR_BUF_SIZE >
- PAGE_SIZE / 2);
+ 2 * ALIGN(NET_IP_ALIGN + EFX_RX_USR_BUF_SIZE,
+ EFX_RX_BUF_ALIGNMENT) >
+ PAGE_SIZE);
efx->rx_scatter = true;
efx->rx_dma_len = EFX_RX_USR_BUF_SIZE;
efx->rx_buffer_order = 0;
/* Maximum possible MTU the driver supports */
#define EFX_MAX_MTU (9 * 1024)
-/* Size of an RX scatter buffer. Small enough to pack 2 into a 4K page. */
-#define EFX_RX_USR_BUF_SIZE 1824
+/* Size of an RX scatter buffer. Small enough to pack 2 into a 4K page,
+ * and should be a multiple of the cache line size.
+ */
+#define EFX_RX_USR_BUF_SIZE (2048 - 256)
+
+/* If possible, we should ensure cache line alignment at start and end
+ * of every buffer. Otherwise, we just need to ensure 4-byte
+ * alignment of the network header.
+ */
+#if NET_IP_ALIGN == 0
+#define EFX_RX_BUF_ALIGNMENT L1_CACHE_BYTES
+#else
+#define EFX_RX_BUF_ALIGNMENT 4
+#endif
/* Forward declare Precision Time Protocol (PTP) support structure. */
struct efx_ptp_data;
STATE_RECOVERY = 3, /* device recovering from PCI error */
};
-/*
- * Alignment of page-allocated RX buffers
- *
- * Controls the number of bytes inserted at the start of an RX buffer.
- * This is the equivalent of NET_IP_ALIGN [which controls the alignment
- * of the skb->head for hardware DMA].
- */
-#ifdef CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
-#define EFX_PAGE_IP_ALIGN 0
-#else
-#define EFX_PAGE_IP_ALIGN NET_IP_ALIGN
-#endif
-
/*
* Alignment of the skb->head which wraps a page-allocated RX buffer
*
* The skb allocated to wrap an rx_buffer can have this alignment. Since
* the data is memcpy'd from the rx_buf, it does not need to be equal to
- * EFX_PAGE_IP_ALIGN.
+ * NET_IP_ALIGN.
*/
#define EFX_PAGE_SKB_ALIGN 2
void efx_rx_config_page_split(struct efx_nic *efx)
{
- efx->rx_page_buf_step = ALIGN(efx->rx_dma_len + EFX_PAGE_IP_ALIGN,
- L1_CACHE_BYTES);
+ efx->rx_page_buf_step = ALIGN(efx->rx_dma_len + NET_IP_ALIGN,
+ EFX_RX_BUF_ALIGNMENT);
efx->rx_bufs_per_page = efx->rx_buffer_order ? 1 :
((PAGE_SIZE - sizeof(struct efx_rx_page_state)) /
efx->rx_page_buf_step);
do {
index = rx_queue->added_count & rx_queue->ptr_mask;
rx_buf = efx_rx_buffer(rx_queue, index);
- rx_buf->dma_addr = dma_addr + EFX_PAGE_IP_ALIGN;
+ rx_buf->dma_addr = dma_addr + NET_IP_ALIGN;
rx_buf->page = page;
- rx_buf->page_offset = page_offset + EFX_PAGE_IP_ALIGN;
+ rx_buf->page_offset = page_offset + NET_IP_ALIGN;
rx_buf->len = efx->rx_dma_len;
rx_buf->flags = 0;
++rx_queue->added_count;
phy_write(lp->phy_dev, MII_CTRL1000, 0);
/* Advertise only 10 and 100mbps full/half duplex speeds */
- phy_write(lp->phy_dev, MII_ADVERTISE, ADVERTISE_ALL);
+ phy_write(lp->phy_dev, MII_ADVERTISE, ADVERTISE_ALL |
+ ADVERTISE_CSMA);
/* Restart auto negotiation */
bmcr = phy_read(lp->phy_dev, MII_BMCR);
#include <linux/inetdevice.h>
#include <linux/etherdevice.h>
#include <linux/skbuff.h>
+#include <linux/if_vlan.h>
#include <linux/in.h>
#include <linux/slab.h>
#include <net/arp.h>
skb->protocol = eth_type_trans(skb, net);
skb->ip_summed = CHECKSUM_NONE;
- skb->vlan_tci = packet->vlan_tci;
+ __vlan_hwaccel_put_tag(skb, htons(ETH_P_8021Q), packet->vlan_tci);
net->stats.rx_packets++;
net->stats.rx_bytes += packet->total_data_buflen;
adv = mmd_eee_adv_to_ethtool_adv_t(eee_adv);
lp = mmd_eee_adv_to_ethtool_adv_t(eee_lp);
idx = phy_find_setting(phydev->speed, phydev->duplex);
- if ((lp & adv & settings[idx].setting))
+ if (!(lp & adv & settings[idx].setting))
goto eee_exit;
if (clk_stop_enable) {
bool incomplete;
int i;
- port = list_first_entry(&team->port_list, struct team_port, list);
+ port = list_first_entry_or_null(&team->port_list,
+ struct team_port, list);
start_again:
err = __send_and_alloc_skb(&skb, team, portid, send_func);
err = team_nl_fill_one_port_get(skb, one_port);
if (err)
goto errout;
- } else {
- list_for_each_entry(port, &team->port_list, list) {
+ } else if (port) {
+ list_for_each_entry_from(port, &team->port_list, list) {
err = team_nl_fill_one_port_get(skb, port);
if (err) {
if (err == -EMSGSIZE) {
else
return -EINVAL;
+ if (!!(ifr->ifr_flags & IFF_MULTI_QUEUE) !=
+ !!(tun->flags & TUN_TAP_MQ))
+ return -EINVAL;
+
if (tun_not_capable(tun))
return -EPERM;
err = security_tun_dev_open(tun->security);
{QMI_FIXED_INTF(0x1bbb, 0x011e, 4)}, /* Telekom Speedstick LTE II (Alcatel One Touch L100V LTE) */
{QMI_FIXED_INTF(0x2357, 0x0201, 4)}, /* TP-LINK HSUPA Modem MA180 */
{QMI_FIXED_INTF(0x1bc7, 0x1200, 5)}, /* Telit LE920 */
+ {QMI_FIXED_INTF(0x1e2d, 0x12d1, 4)}, /* Cinterion PLxx */
/* 4. Gobi 1000 devices */
{QMI_GOBI1K_DEVICE(0x05c6, 0x9212)}, /* Acer Gobi Modem Device */
struct usb_device *udev;
struct tasklet_struct tl;
struct net_device *netdev;
- struct urb *rx_urb, *tx_urb, *intr_urb, *ctrl_urb;
+ struct urb *rx_urb, *tx_urb, *intr_urb;
struct sk_buff *tx_skb, *rx_skb;
struct sk_buff *rx_skb_pool[RX_SKB_POOL_SIZE];
spinlock_t rx_pool_lock;
struct usb_ctrlrequest dr;
int intr_interval;
- __le16 rx_creg;
u8 *intr_buff;
u8 phy;
};
typedef struct rtl8150 rtl8150_t;
+struct async_req {
+ struct usb_ctrlrequest dr;
+ u16 rx_creg;
+};
+
static const char driver_name [] = "rtl8150";
/*
indx, 0, data, size, 500);
}
-static void ctrl_callback(struct urb *urb)
+static void async_set_reg_cb(struct urb *urb)
{
- rtl8150_t *dev;
+ struct async_req *req = (struct async_req *)urb->context;
int status = urb->status;
- switch (status) {
- case 0:
- break;
- case -EINPROGRESS:
- break;
- case -ENOENT:
- break;
- default:
- if (printk_ratelimit())
- dev_warn(&urb->dev->dev, "ctrl urb status %d\n", status);
- }
- dev = urb->context;
- clear_bit(RX_REG_SET, &dev->flags);
+ if (status < 0)
+ dev_dbg(&urb->dev->dev, "%s failed with %d", __func__, status);
+ kfree(req);
+ usb_free_urb(urb);
}
-static int async_set_registers(rtl8150_t * dev, u16 indx, u16 size)
+static int async_set_registers(rtl8150_t *dev, u16 indx, u16 size, u16 reg)
{
- int ret;
-
- if (test_bit(RX_REG_SET, &dev->flags))
- return -EAGAIN;
+ int res = -ENOMEM;
+ struct urb *async_urb;
+ struct async_req *req;
- dev->dr.bRequestType = RTL8150_REQT_WRITE;
- dev->dr.bRequest = RTL8150_REQ_SET_REGS;
- dev->dr.wValue = cpu_to_le16(indx);
- dev->dr.wIndex = 0;
- dev->dr.wLength = cpu_to_le16(size);
- dev->ctrl_urb->transfer_buffer_length = size;
- usb_fill_control_urb(dev->ctrl_urb, dev->udev,
- usb_sndctrlpipe(dev->udev, 0), (char *) &dev->dr,
- &dev->rx_creg, size, ctrl_callback, dev);
- if ((ret = usb_submit_urb(dev->ctrl_urb, GFP_ATOMIC))) {
- if (ret == -ENODEV)
+ req = kmalloc(sizeof(struct async_req), GFP_ATOMIC);
+ if (req == NULL)
+ return res;
+ async_urb = usb_alloc_urb(0, GFP_ATOMIC);
+ if (async_urb == NULL) {
+ kfree(req);
+ return res;
+ }
+ req->rx_creg = cpu_to_le16(reg);
+ req->dr.bRequestType = RTL8150_REQT_WRITE;
+ req->dr.bRequest = RTL8150_REQ_SET_REGS;
+ req->dr.wIndex = 0;
+ req->dr.wValue = cpu_to_le16(indx);
+ req->dr.wLength = cpu_to_le16(size);
+ usb_fill_control_urb(async_urb, dev->udev,
+ usb_sndctrlpipe(dev->udev, 0), (void *)&req->dr,
+ &req->rx_creg, size, async_set_reg_cb, req);
+ res = usb_submit_urb(async_urb, GFP_ATOMIC);
+ if (res) {
+ if (res == -ENODEV)
netif_device_detach(dev->netdev);
- dev_err(&dev->udev->dev,
- "control request submission failed: %d\n", ret);
- } else
- set_bit(RX_REG_SET, &dev->flags);
-
- return ret;
+ dev_err(&dev->udev->dev, "%s failed with %d\n", __func__, res);
+ }
+ return res;
}
static int read_mii_word(rtl8150_t * dev, u8 phy, __u8 indx, u16 * reg)
usb_free_urb(dev->tx_urb);
return 0;
}
- dev->ctrl_urb = usb_alloc_urb(0, GFP_KERNEL);
- if (!dev->ctrl_urb) {
- usb_free_urb(dev->rx_urb);
- usb_free_urb(dev->tx_urb);
- usb_free_urb(dev->intr_urb);
- return 0;
- }
return 1;
}
usb_free_urb(dev->rx_urb);
usb_free_urb(dev->tx_urb);
usb_free_urb(dev->intr_urb);
- usb_free_urb(dev->ctrl_urb);
}
static void unlink_all_urbs(rtl8150_t * dev)
usb_kill_urb(dev->rx_urb);
usb_kill_urb(dev->tx_urb);
usb_kill_urb(dev->intr_urb);
- usb_kill_urb(dev->ctrl_urb);
}
static inline struct sk_buff *pull_skb(rtl8150_t *dev)
}
/* RCR bit7=1 attach Rx info at the end; =0 HW CRC (which is broken) */
rcr = 0x9e;
- dev->rx_creg = cpu_to_le16(rcr);
tcr = 0xd8;
cr = 0x0c;
if (!(rcr & 0x80))
static void rtl8150_set_multicast(struct net_device *netdev)
{
rtl8150_t *dev = netdev_priv(netdev);
+ u16 rx_creg = 0x9e;
+
netif_stop_queue(netdev);
if (netdev->flags & IFF_PROMISC) {
- dev->rx_creg |= cpu_to_le16(0x0001);
+ rx_creg |= 0x0001;
dev_info(&netdev->dev, "%s: promiscuous mode\n", netdev->name);
} else if (!netdev_mc_empty(netdev) ||
(netdev->flags & IFF_ALLMULTI)) {
- dev->rx_creg &= cpu_to_le16(0xfffe);
- dev->rx_creg |= cpu_to_le16(0x0002);
+ rx_creg &= 0xfffe;
+ rx_creg |= 0x0002;
dev_info(&netdev->dev, "%s: allmulti set\n", netdev->name);
} else {
/* ~RX_MULTICAST, ~RX_PROMISCUOUS */
- dev->rx_creg &= cpu_to_le16(0x00fc);
+ rx_creg &= 0x00fc;
}
- async_set_registers(dev, RCR, 2);
+ async_set_registers(dev, RCR, sizeof(rx_creg), rx_creg);
netif_wake_queue(netdev);
}
/* usbnet already took usb runtime pm, so have to enable the feature
* for usb interface, otherwise usb_autopm_get_interface may return
- * failure if USB_SUSPEND(RUNTIME_PM) is enabled.
+ * failure if RUNTIME_PM is enabled.
*/
if (!driver->supports_autosuspend) {
driver->supports_autosuspend = 1;
struct virtnet_info *vi = netdev_priv(dev);
int i;
- for (i = 0; i < vi->curr_queue_pairs; i++) {
- /* Make sure we have some buffers: if oom use wq. */
- if (!try_fill_recv(&vi->rq[i], GFP_KERNEL))
- schedule_delayed_work(&vi->refill, 0);
+ for (i = 0; i < vi->max_queue_pairs; i++) {
+ if (i < vi->curr_queue_pairs)
+ /* Make sure we have some buffers: if oom use wq. */
+ if (!try_fill_recv(&vi->rq[i], GFP_KERNEL))
+ schedule_delayed_work(&vi->refill, 0);
virtnet_napi_enable(&vi->rq[i]);
}
}
/* Look up Ethernet address in forwarding table */
-static struct vxlan_fdb *vxlan_find_mac(struct vxlan_dev *vxlan,
+static struct vxlan_fdb *__vxlan_find_mac(struct vxlan_dev *vxlan,
const u8 *mac)
{
return NULL;
}
+static struct vxlan_fdb *vxlan_find_mac(struct vxlan_dev *vxlan,
+ const u8 *mac)
+{
+ struct vxlan_fdb *f;
+
+ f = __vxlan_find_mac(vxlan, mac);
+ if (f)
+ f->used = jiffies;
+
+ return f;
+}
+
/* Add/update destinations for multicast */
static int vxlan_fdb_append(struct vxlan_fdb *f,
__be32 ip, __be16 port, __u32 vni, __u32 ifindex)
struct vxlan_fdb *f;
int notify = 0;
- f = vxlan_find_mac(vxlan, mac);
+ f = __vxlan_find_mac(vxlan, mac);
if (f) {
if (flags & NLM_F_EXCL) {
netdev_dbg(vxlan->dev,
f = vxlan_find_mac(vxlan, src_mac);
if (likely(f)) {
- f->used = jiffies;
if (likely(f->remote.remote_ip == src_ip))
return;
{
int i;
- if (!AR_SREV_9462(ah) && !AR_SREV_9565(ah))
+ if (!AR_SREV_9462(ah) && !AR_SREV_9565(ah) && !AR_SREV_9485(ah))
return;
for (i = 0; i < AR9300_MAX_CHAINS; i++) {
#define AR9300_BASE_ADDR 0x3ff
#define AR9300_BASE_ADDR_512 0x1ff
-#define AR9300_OTP_BASE (AR_SREV_9340(ah) ? 0x30000 : 0x14000)
-#define AR9300_OTP_STATUS (AR_SREV_9340(ah) ? 0x30018 : 0x15f18)
+#define AR9300_OTP_BASE \
+ ((AR_SREV_9340(ah) || AR_SREV_9550(ah)) ? 0x30000 : 0x14000)
+#define AR9300_OTP_STATUS \
+ ((AR_SREV_9340(ah) || AR_SREV_9550(ah)) ? 0x30018 : 0x15f18)
#define AR9300_OTP_STATUS_TYPE 0x7
#define AR9300_OTP_STATUS_VALID 0x4
#define AR9300_OTP_STATUS_ACCESS_BUSY 0x2
#define AR9300_OTP_STATUS_SM_BUSY 0x1
-#define AR9300_OTP_READ_DATA (AR_SREV_9340(ah) ? 0x3001c : 0x15f1c)
+#define AR9300_OTP_READ_DATA \
+ ((AR_SREV_9340(ah) || AR_SREV_9550(ah)) ? 0x3001c : 0x15f1c)
enum targetPowerHTRates {
HT_TARGET_RATE_0_8_16,
REG_RMW_FIELD(ah, AR_PHY_SPUR_REG,
AR_PHY_SPUR_REG_EN_VIT_SPUR_RSSI, 1);
- if (REG_READ_FIELD(ah, AR_PHY_MODE,
+ if (!AR_SREV_9340(ah) &&
+ REG_READ_FIELD(ah, AR_PHY_MODE,
AR_PHY_MODE_DYNAMIC) == 0x1)
REG_RMW_FIELD(ah, AR_PHY_SPUR_REG,
AR_PHY_SPUR_REG_ENABLE_NF_RSSI_SPUR_MIT, 1);
{0x0000a284, 0x00000000, 0x00000000, 0x000002a0, 0x000002a0},
{0x0000a288, 0x00000000, 0x00000000, 0x00000000, 0x00000000},
{0x0000a28c, 0x00000000, 0x00000000, 0x00000000, 0x00000000},
- {0x0000a2c4, 0x00158d18, 0x00158d18, 0x00158d18, 0x00158d18},
+ {0x0000a2c4, 0x00158d18, 0x00158d18, 0x00058d18, 0x00058d18},
{0x0000a2d0, 0x00071981, 0x00071981, 0x00071982, 0x00071982},
{0x0000a2d8, 0xf999a83a, 0xf999a83a, 0xf999a83a, 0xf999a83a},
{0x0000a358, 0x00000000, 0x00000000, 0x00000000, 0x00000000},
int tidno;
int baw_head; /* first un-acked tx buffer */
int baw_tail; /* next unused tx buffer slot */
- int sched;
- int paused;
- u8 state;
+ bool sched;
+ bool paused;
+ bool active;
};
struct ath_node {
#endif
};
-#define AGGR_CLEANUP BIT(1)
-#define AGGR_ADDBA_COMPLETE BIT(2)
-#define AGGR_ADDBA_PROGRESS BIT(3)
-
struct ath_tx_control {
struct ath_txq *txq;
struct ath_node *an;
WARN_ON(i != ATH9K_SSTATS_LEN);
}
+void ath9k_deinit_debug(struct ath_softc *sc)
+{
+ if (config_enabled(CONFIG_ATH9K_DEBUGFS) && sc->rfs_chan_spec_scan) {
+ relay_close(sc->rfs_chan_spec_scan);
+ sc->rfs_chan_spec_scan = NULL;
+ }
+}
+
int ath9k_init_debug(struct ath_hw *ah)
{
struct ath_common *common = ath9k_hw_common(ah);
};
int ath9k_init_debug(struct ath_hw *ah);
+void ath9k_deinit_debug(struct ath_softc *sc);
void ath_debug_stat_interrupt(struct ath_softc *sc, enum ath9k_int status);
void ath_debug_stat_tx(struct ath_softc *sc, struct ath_buf *bf,
return 0;
}
+static inline void ath9k_deinit_debug(struct ath_softc *sc)
+{
+}
+
static inline void ath_debug_stat_interrupt(struct ath_softc *sc,
enum ath9k_int status)
{
static inline void ath9k_hw_set_dma(struct ath_hw *ah)
{
struct ath_common *common = ath9k_hw_common(ah);
+ int txbuf_size;
ENABLE_REGWRITE_BUFFER(ah);
* So set the usable tx buf size also to half to
* avoid data/delimiter underruns
*/
- REG_WRITE(ah, AR_PCU_TXBUF_CTRL,
- AR_9285_PCU_TXBUF_CTRL_USABLE_SIZE);
- } else if (!AR_SREV_9271(ah)) {
- REG_WRITE(ah, AR_PCU_TXBUF_CTRL,
- AR_PCU_TXBUF_CTRL_USABLE_SIZE);
+ txbuf_size = AR_9285_PCU_TXBUF_CTRL_USABLE_SIZE;
+ } else if (AR_SREV_9340_13_OR_LATER(ah)) {
+ /* Uses fewer entries for AR934x v1.3+ to prevent rx overruns */
+ txbuf_size = AR_9340_PCU_TXBUF_CTRL_USABLE_SIZE;
+ } else {
+ txbuf_size = AR_PCU_TXBUF_CTRL_USABLE_SIZE;
}
+ if (!AR_SREV_9271(ah))
+ REG_WRITE(ah, AR_PCU_TXBUF_CTRL, txbuf_size);
+
REGWRITE_BUFFER_FLUSH(ah);
if (AR_SREV_9300_20_OR_LATER(ah))
AR_RTC_RC_COLD_RESET | AR_RTC_RC_WARM_RESET;
} else {
tmpReg = REG_READ(ah, AR_INTR_SYNC_CAUSE);
- if (tmpReg &
- (AR_INTR_SYNC_LOCAL_TIMEOUT |
- AR_INTR_SYNC_RADM_CPL_TIMEOUT)) {
+ if (AR_SREV_9340(ah))
+ tmpReg &= AR9340_INTR_SYNC_LOCAL_TIMEOUT;
+ else
+ tmpReg &= AR_INTR_SYNC_LOCAL_TIMEOUT |
+ AR_INTR_SYNC_RADM_CPL_TIMEOUT;
+
+ if (tmpReg) {
u32 val;
REG_WRITE(ah, AR_INTR_SYNC_ENABLE, 0);
if (!ath_is_world_regd(reg)) {
error = regulatory_hint(hw->wiphy, reg->alpha2);
if (error)
- goto unregister;
+ goto debug_cleanup;
}
ath_init_leds(sc);
return 0;
+debug_cleanup:
+ ath9k_deinit_debug(sc);
unregister:
ieee80211_unregister_hw(hw);
rx_cleanup:
sc->dfs_detector->exit(sc->dfs_detector);
ath9k_eeprom_release(sc);
-
- if (config_enabled(CONFIG_ATH9K_DEBUGFS) && sc->rfs_chan_spec_scan) {
- relay_close(sc->rfs_chan_spec_scan);
- sc->rfs_chan_spec_scan = NULL;
- }
}
void ath9k_deinit_device(struct ath_softc *sc)
ath9k_ps_restore(sc);
+ ath9k_deinit_debug(sc);
ieee80211_unregister_hw(hw);
ath_rx_cleanup(sc);
ath9k_deinit_softc(sc);
REG_WRITE(ah, AR_QMISC(q), AR_Q_MISC_DCU_EARLY_TERM_REQ);
- if (AR_SREV_9340(ah))
+ if (AR_SREV_9340(ah) && !AR_SREV_9340_13_OR_LATER(ah))
REG_WRITE(ah, AR_DMISC(q),
AR_D_MISC_CW_BKOFF_EN | AR_D_MISC_FRAG_WAIT_EN | 0x1);
else
u16 tid, u16 *ssn, u8 buf_size)
{
struct ath_softc *sc = hw->priv;
+ bool flush = false;
int ret = 0;
local_bh_disable();
ieee80211_start_tx_ba_cb_irqsafe(vif, sta->addr, tid);
ath9k_ps_restore(sc);
break;
- case IEEE80211_AMPDU_TX_STOP_CONT:
case IEEE80211_AMPDU_TX_STOP_FLUSH:
case IEEE80211_AMPDU_TX_STOP_FLUSH_CONT:
+ flush = true;
+ case IEEE80211_AMPDU_TX_STOP_CONT:
ath9k_ps_wakeup(sc);
ath_tx_aggr_stop(sc, sta, tid);
- ieee80211_stop_tx_ba_cb_irqsafe(vif, sta->addr, tid);
+ if (!flush)
+ ieee80211_stop_tx_ba_cb_irqsafe(vif, sta->addr, tid);
ath9k_ps_restore(sc);
break;
case IEEE80211_AMPDU_TX_OPERATIONAL:
return false;
txtid = ATH_AN_2_TID(an, tidno);
-
- if (!(txtid->state & (AGGR_ADDBA_COMPLETE | AGGR_ADDBA_PROGRESS)))
- return true;
- return false;
+ return !txtid->active;
}
#define AR_SREV_REVISION_9485_10 0
#define AR_SREV_REVISION_9485_11 1
#define AR_SREV_VERSION_9340 0x300
+#define AR_SREV_REVISION_9340_10 0
+#define AR_SREV_REVISION_9340_11 1
+#define AR_SREV_REVISION_9340_12 2
+#define AR_SREV_REVISION_9340_13 3
#define AR_SREV_VERSION_9580 0x1C0
#define AR_SREV_REVISION_9580_10 4 /* AR9580 1.0 */
#define AR_SREV_VERSION_9462 0x280
#define AR_SREV_9340(_ah) \
(((_ah)->hw_version.macVersion == AR_SREV_VERSION_9340))
+#define AR_SREV_9340_13_OR_LATER(_ah) \
+ (AR_SREV_9340((_ah)) && \
+ ((_ah)->hw_version.macRev >= AR_SREV_REVISION_9340_13))
+
#define AR_SREV_9285E_20(_ah) \
(AR_SREV_9285_12_OR_LATER(_ah) && \
((REG_READ(_ah, AR_AN_SYNTH9) & 0x7) == 0x1))
AR_INTR_SYNC_LOCAL_TIMEOUT |
AR_INTR_SYNC_MAC_SLEEP_ACCESS),
+ AR9340_INTR_SYNC_LOCAL_TIMEOUT = 0x00000010,
+
AR_INTR_SYNC_SPURIOUS = 0xFFFFFFFF,
};
#define AR_PCU_TXBUF_CTRL_SIZE_MASK 0x7FF
#define AR_PCU_TXBUF_CTRL_USABLE_SIZE 0x700
#define AR_9285_PCU_TXBUF_CTRL_USABLE_SIZE 0x380
+#define AR_9340_PCU_TXBUF_CTRL_USABLE_SIZE 0x500
#define AR_PCU_MISC_MODE2 0x8344
#define AR_PCU_MISC_MODE2_MGMT_CRYPTO_ENABLE 0x00000002
list_add_tail(&ac->list, &txq->axq_acq);
}
-static void ath_tx_resume_tid(struct ath_softc *sc, struct ath_atx_tid *tid)
-{
- struct ath_txq *txq = tid->ac->txq;
-
- WARN_ON(!tid->paused);
-
- ath_txq_lock(sc, txq);
- tid->paused = false;
-
- if (skb_queue_empty(&tid->buf_q))
- goto unlock;
-
- ath_tx_queue_tid(txq, tid);
- ath_txq_schedule(sc, txq);
-unlock:
- ath_txq_unlock_complete(sc, txq);
-}
-
static struct ath_frame_info *get_frame_info(struct sk_buff *skb)
{
struct ieee80211_tx_info *tx_info = IEEE80211_SKB_CB(skb);
}
}
- if (tid->baw_head == tid->baw_tail) {
- tid->state &= ~AGGR_ADDBA_COMPLETE;
- tid->state &= ~AGGR_CLEANUP;
- }
-
if (sendbar) {
ath_txq_unlock(sc, txq);
ath_send_bar(tid, tid->seq_start);
list_add_tail(&bf->list, &bf_head);
- if (fi->retries)
- ath_tx_update_baw(sc, tid, bf->bf_state.seqno);
-
+ ath_tx_update_baw(sc, tid, bf->bf_state.seqno);
ath_tx_complete_buf(sc, bf, txq, &bf_head, &ts, 0);
}
tx_info = IEEE80211_SKB_CB(skb);
fi = get_frame_info(skb);
- if (ATH_BA_ISSET(ba, ATH_BA_INDEX(seq_st, seqno))) {
+ if (!BAW_WITHIN(tid->seq_start, tid->baw_size, seqno)) {
+ /*
+ * Outside of the current BlockAck window,
+ * maybe part of a previous session
+ */
+ txfail = 1;
+ } else if (ATH_BA_ISSET(ba, ATH_BA_INDEX(seq_st, seqno))) {
/* transmit completion, subframe is
* acked by block ack */
acked_cnt++;
} else if (!isaggr && txok) {
/* transmit completion */
acked_cnt++;
- } else if (tid->state & AGGR_CLEANUP) {
- /*
- * cleanup in progress, just fail
- * the un-acked sub-frames
- */
- txfail = 1;
} else if (flush) {
txpending = 1;
} else if (fi->retries < ATH_MAX_SW_RETRIES) {
if (bf_next != NULL || !bf_last->bf_stale)
list_move_tail(&bf->list, &bf_head);
- if (!txpending || (tid->state & AGGR_CLEANUP)) {
+ if (!txpending) {
/*
* complete the acked-ones/xretried ones; update
* block-ack window
ath_txq_lock(sc, txq);
}
- if (tid->state & AGGR_CLEANUP)
- ath_tx_flush_tid(sc, tid);
-
rcu_read_unlock();
if (needreset)
struct ath_tx_status *ts, struct ath_buf *bf,
struct list_head *bf_head)
{
+ struct ieee80211_tx_info *info;
bool txok, flush;
txok = !(ts->ts_status & ATH9K_TXERR_MASK);
txq->axq_ampdu_depth--;
if (!bf_isampdu(bf)) {
- if (!flush)
+ if (!flush) {
+ info = IEEE80211_SKB_CB(bf->bf_mpdu);
+ memcpy(info->control.rates, bf->rates,
+ sizeof(info->control.rates));
ath_tx_rc_status(sc, bf, ts, 1, txok ? 0 : 1, txok);
+ }
ath_tx_complete_buf(sc, bf, txq, bf_head, ts, txok);
} else
ath_tx_complete_aggr(sc, txq, bf, bf_head, ts, txok);
skb = bf->bf_mpdu;
tx_info = IEEE80211_SKB_CB(skb);
- rates = tx_info->control.rates;
+ rates = bf->rates;
/*
* Find the lowest frame length among the rate series that will have a
an = (struct ath_node *)sta->drv_priv;
txtid = ATH_AN_2_TID(an, tid);
- if (txtid->state & (AGGR_CLEANUP | AGGR_ADDBA_COMPLETE))
- return -EAGAIN;
-
/* update ampdu factor/density, they may have changed. This may happen
* in HT IBSS when a beacon with HT-info is received after the station
* has already been added.
an->mpdudensity = density;
}
- txtid->state |= AGGR_ADDBA_PROGRESS;
+ txtid->active = true;
txtid->paused = true;
*ssn = txtid->seq_start = txtid->seq_next;
txtid->bar_index = -1;
struct ath_atx_tid *txtid = ATH_AN_2_TID(an, tid);
struct ath_txq *txq = txtid->ac->txq;
- if (txtid->state & AGGR_CLEANUP)
- return;
-
- if (!(txtid->state & AGGR_ADDBA_COMPLETE)) {
- txtid->state &= ~AGGR_ADDBA_PROGRESS;
- return;
- }
-
ath_txq_lock(sc, txq);
+ txtid->active = false;
txtid->paused = true;
-
- /*
- * If frames are still being transmitted for this TID, they will be
- * cleaned up during tx completion. To prevent race conditions, this
- * TID can only be reused after all in-progress subframes have been
- * completed.
- */
- if (txtid->baw_head != txtid->baw_tail)
- txtid->state |= AGGR_CLEANUP;
- else
- txtid->state &= ~AGGR_ADDBA_COMPLETE;
-
ath_tx_flush_tid(sc, txtid);
ath_txq_unlock_complete(sc, txq);
}
}
}
-void ath_tx_aggr_resume(struct ath_softc *sc, struct ieee80211_sta *sta, u16 tid)
+void ath_tx_aggr_resume(struct ath_softc *sc, struct ieee80211_sta *sta,
+ u16 tidno)
{
- struct ath_atx_tid *txtid;
+ struct ath_atx_tid *tid;
struct ath_node *an;
+ struct ath_txq *txq;
an = (struct ath_node *)sta->drv_priv;
+ tid = ATH_AN_2_TID(an, tidno);
+ txq = tid->ac->txq;
- txtid = ATH_AN_2_TID(an, tid);
- txtid->baw_size = IEEE80211_MIN_AMPDU_BUF << sta->ht_cap.ampdu_factor;
- txtid->state |= AGGR_ADDBA_COMPLETE;
- txtid->state &= ~AGGR_ADDBA_PROGRESS;
- ath_tx_resume_tid(sc, txtid);
+ ath_txq_lock(sc, txq);
+
+ tid->baw_size = IEEE80211_MIN_AMPDU_BUF << sta->ht_cap.ampdu_factor;
+ tid->paused = false;
+
+ if (!skb_queue_empty(&tid->buf_q)) {
+ ath_tx_queue_tid(txq, tid);
+ ath_txq_schedule(sc, txq);
+ }
+
+ ath_txq_unlock_complete(sc, txq);
}
/********************/
tid->baw_head = tid->baw_tail = 0;
tid->sched = false;
tid->paused = false;
- tid->state &= ~AGGR_CLEANUP;
+ tid->active = false;
__skb_queue_head_init(&tid->buf_q);
acno = TID_TO_WME_AC(tidno);
tid->ac = &an->ac[acno];
- tid->state &= ~AGGR_ADDBA_COMPLETE;
- tid->state &= ~AGGR_ADDBA_PROGRESS;
}
for (acno = 0, ac = &an->ac[acno];
}
ath_tid_drain(sc, txq, tid);
- tid->state &= ~AGGR_ADDBA_COMPLETE;
- tid->state &= ~AGGR_CLEANUP;
+ tid->active = false;
ath_txq_unlock(sc, txq);
}
netif_carrier_off(dev);
- if (!proc_create_data("driver/atmel", 0, NULL, &atmel_proc_fops, priv));
+ if (!proc_create_data("driver/atmel", 0, NULL, &atmel_proc_fops, priv))
printk(KERN_WARNING "atmel: unable to create /proc entry.\n");
printk(KERN_INFO "%s: Atmel at76c50x. Version %d.%d. MAC %pM\n",
#include "tracepoint.h"
#define PKTFILTER_BUF_SIZE 128
-#define BRCMF_ARPOL_MODE 0xb /* agent|snoop|peer_autoreply */
#define BRCMF_DEFAULT_BCN_TIMEOUT 3
#define BRCMF_DEFAULT_SCAN_CHANNEL_TIME 40
#define BRCMF_DEFAULT_SCAN_UNASSOC_TIME 40
goto done;
}
- /* Try to set and enable ARP offload feature, this may fail */
- err = brcmf_fil_iovar_int_set(ifp, "arp_ol", BRCMF_ARPOL_MODE);
- if (err) {
- brcmf_dbg(TRACE, "failed to set ARP offload mode to 0x%x, err = %d\n",
- BRCMF_ARPOL_MODE, err);
- err = 0;
- } else {
- err = brcmf_fil_iovar_int_set(ifp, "arpoe", 1);
- if (err) {
- brcmf_dbg(TRACE, "failed to enable ARP offload err = %d\n",
- err);
- err = 0;
- } else
- brcmf_dbg(TRACE, "successfully enabled ARP offload to 0x%x\n",
- BRCMF_ARPOL_MODE);
- }
-
/* Setup packet filter */
brcmf_c_pktfilter_offload_set(ifp, BRCMF_DEFAULT_PACKET_FILTER);
brcmf_c_pktfilter_offload_enable(ifp, BRCMF_DEFAULT_PACKET_FILTER,
brcmf_dbg(INFO, "%s: Broadcom Dongle Host Driver\n", ndev->name);
+ ndev->destructor = free_netdev;
return 0;
fail:
+ drvr->iflist[ifp->bssidx] = NULL;
ndev->netdev_ops = NULL;
+ free_netdev(ndev);
return -EBADE;
}
return 0;
fail:
+ ifp->drvr->iflist[ifp->bssidx] = NULL;
+ ndev->netdev_ops = NULL;
+ free_netdev(ndev);
return -EBADE;
}
struct brcmf_if *ifp;
ifp = drvr->iflist[bssidx];
+ drvr->iflist[bssidx] = NULL;
if (!ifp) {
brcmf_err("Null interface, idx=%d\n", bssidx);
return;
cancel_work_sync(&ifp->setmacaddr_work);
cancel_work_sync(&ifp->multicast_work);
}
-
+ /* unregister will take care of freeing it */
unregister_netdev(ifp->ndev);
if (bssidx == 0)
brcmf_cfg80211_detach(drvr->config);
- free_netdev(ifp->ndev);
} else {
kfree(ifp);
}
- drvr->iflist[bssidx] = NULL;
}
int brcmf_attach(uint bus_hdrlen, struct device *dev)
brcmf_fws_del_interface(ifp);
brcmf_fws_deinit(drvr);
}
- free_netdev(ifp->ndev);
- drvr->iflist[0] = NULL;
if (p2p_ifp) {
free_netdev(p2p_ifp->ndev);
drvr->iflist[1] = NULL;
return ret;
}
if ((brcmf_p2p_enable) && (p2p_ifp))
- brcmf_net_p2p_attach(p2p_ifp);
+ if (brcmf_net_p2p_attach(p2p_ifp) < 0)
+ brcmf_p2p_enable = 0;
return 0;
}
return;
brcmf_fws_add_interface(ifp);
if (!drvr->fweh.evt_handler[BRCMF_E_IF])
- err = brcmf_net_attach(ifp, false);
+ if (brcmf_net_attach(ifp, false) < 0)
+ return;
}
if (ifevent->action == BRCMF_E_IF_CHANGE)
#define BRCMF_FIL_ACTION_FRAME_SIZE 1800
+/* ARP Offload feature flags for arp_ol iovar */
+#define BRCMF_ARP_OL_AGENT 0x00000001
+#define BRCMF_ARP_OL_SNOOP 0x00000002
+#define BRCMF_ARP_OL_HOST_AUTO_REPLY 0x00000004
+#define BRCMF_ARP_OL_PEER_AUTO_REPLY 0x00000008
+
enum brcmf_fil_p2p_if_types {
BRCMF_FIL_P2P_IF_CLIENT,
#define IS_P2P_SOCIAL_CHANNEL(channel) ((channel == SOCIAL_CHAN_1) || \
(channel == SOCIAL_CHAN_2) || \
(channel == SOCIAL_CHAN_3))
+#define BRCMF_P2P_TEMP_CHAN SOCIAL_CHAN_3
#define SOCIAL_CHAN_CNT 3
#define AF_PEER_SEARCH_CNT 2
err = brcmf_fil_iovar_int_set(pri_ifp, "p2p_disc", 1);
if (err < 0) {
brcmf_err("set p2p_disc error\n");
- brcmf_free_vif(p2p_vif);
+ brcmf_free_vif(cfg, p2p_vif);
goto exit;
}
/* obtain bsscfg index for P2P discovery */
err = brcmf_fil_iovar_int_get(pri_ifp, "p2p_dev", &bssidx);
if (err < 0) {
brcmf_err("retrieving discover bsscfg index failed\n");
- brcmf_free_vif(p2p_vif);
+ brcmf_free_vif(cfg, p2p_vif);
goto exit;
}
/* Verify that firmware uses same bssidx as driver !! */
if (p2p_ifp->bssidx != bssidx) {
brcmf_err("Incorrect bssidx=%d, compared to p2p_ifp->bssidx=%d\n",
bssidx, p2p_ifp->bssidx);
- brcmf_free_vif(p2p_vif);
+ brcmf_free_vif(cfg, p2p_vif);
goto exit;
}
brcmf_p2p_cancel_remain_on_channel(vif->ifp);
brcmf_p2p_deinit_discovery(p2p);
/* remove discovery interface */
- brcmf_free_vif(vif);
+ brcmf_free_vif(p2p->cfg, vif);
p2p->bss_idx[P2PAPI_BSSCFG_DEVICE].vif = NULL;
}
/* just set it all to zero */
u16 *chanspec)
{
struct brcmf_if *ifp;
- struct brcmf_fil_chan_info_le ci;
+ u8 mac_addr[ETH_ALEN];
struct brcmu_chan ch;
- s32 err;
+ struct brcmf_bss_info_le *bi;
+ u8 *buf;
ifp = p2p->bss_idx[P2PAPI_BSSCFG_PRIMARY].vif->ifp;
- ch.chnum = 11;
-
- err = brcmf_fil_cmd_data_get(ifp, BRCMF_C_GET_CHANNEL, &ci, sizeof(ci));
- if (!err)
- ch.chnum = le32_to_cpu(ci.hw_channel);
+ if (brcmf_fil_cmd_data_get(ifp, BRCMF_C_GET_BSSID, mac_addr,
+ ETH_ALEN) == 0) {
+ buf = kzalloc(WL_BSS_INFO_MAX, GFP_KERNEL);
+ if (buf != NULL) {
+ *(__le32 *)buf = cpu_to_le32(WL_BSS_INFO_MAX);
+ if (brcmf_fil_cmd_data_get(ifp, BRCMF_C_GET_BSS_INFO,
+ buf, WL_BSS_INFO_MAX) == 0) {
+ bi = (struct brcmf_bss_info_le *)(buf + 4);
+ *chanspec = le16_to_cpu(bi->chanspec);
+ kfree(buf);
+ return;
+ }
+ kfree(buf);
+ }
+ }
+ /* Use default channel for P2P */
+ ch.chnum = BRCMF_P2P_TEMP_CHAN;
ch.bw = BRCMU_CHAN_BW_20;
p2p->cfg->d11inf.encchspec(&ch);
*chanspec = ch.chspec;
return &p2p_vif->wdev;
fail:
- brcmf_free_vif(p2p_vif);
+ brcmf_free_vif(p2p->cfg, p2p_vif);
return ERR_PTR(err);
}
*
* @vif: virtual interface object to delete.
*/
-static void brcmf_p2p_delete_p2pdev(struct brcmf_cfg80211_vif *vif)
+static void brcmf_p2p_delete_p2pdev(struct brcmf_cfg80211_info *cfg,
+ struct brcmf_cfg80211_vif *vif)
{
- struct brcmf_p2p_info *p2p = &vif->ifp->drvr->config->p2p;
-
cfg80211_unregister_wdev(&vif->wdev);
- p2p->bss_idx[P2PAPI_BSSCFG_DEVICE].vif = NULL;
- brcmf_free_vif(vif);
+ cfg->p2p.bss_idx[P2PAPI_BSSCFG_DEVICE].vif = NULL;
+ brcmf_free_vif(cfg, vif);
+}
+
+/**
+ * brcmf_p2p_free_p2p_if() - free up net device related data.
+ *
+ * @ndev: net device that needs to be freed.
+ */
+static void brcmf_p2p_free_p2p_if(struct net_device *ndev)
+{
+ struct brcmf_cfg80211_info *cfg;
+ struct brcmf_cfg80211_vif *vif;
+ struct brcmf_if *ifp;
+
+ ifp = netdev_priv(ndev);
+ cfg = ifp->drvr->config;
+ vif = ifp->vif;
+
+ brcmf_free_vif(cfg, vif);
+ free_netdev(ifp->ndev);
}
/**
brcmf_err("Registering netdevice failed\n");
goto fail;
}
+ /* override destructor */
+ ifp->ndev->destructor = brcmf_p2p_free_p2p_if;
+
cfg->p2p.bss_idx[P2PAPI_BSSCFG_CONNECTION].vif = vif;
/* Disable firmware roaming for P2P interface */
brcmf_fil_iovar_int_set(ifp, "roam_off", 1);
return &ifp->vif->wdev;
fail:
- brcmf_free_vif(vif);
+ brcmf_free_vif(cfg, vif);
return ERR_PTR(err);
}
break;
case NL80211_IFTYPE_P2P_DEVICE:
- brcmf_p2p_delete_p2pdev(vif);
+ brcmf_p2p_delete_p2pdev(cfg, vif);
return 0;
default:
return -ENOTSUPP;
err = 0;
}
brcmf_cfg80211_arm_vif_event(cfg, NULL);
- brcmf_free_vif(vif);
p2p->bss_idx[P2PAPI_BSSCFG_CONNECTION].vif = NULL;
return err;
return err;
}
+static s32
+brcmf_configure_arp_offload(struct brcmf_if *ifp, bool enable)
+{
+ s32 err;
+ u32 mode;
+
+ if (enable)
+ mode = BRCMF_ARP_OL_AGENT | BRCMF_ARP_OL_PEER_AUTO_REPLY;
+ else
+ mode = 0;
+
+ /* Try to set and enable ARP offload feature, this may fail, then it */
+ /* is simply not supported and err 0 will be returned */
+ err = brcmf_fil_iovar_int_set(ifp, "arp_ol", mode);
+ if (err) {
+ brcmf_dbg(TRACE, "failed to set ARP offload mode to 0x%x, err = %d\n",
+ mode, err);
+ err = 0;
+ } else {
+ err = brcmf_fil_iovar_int_set(ifp, "arpoe", enable);
+ if (err) {
+ brcmf_dbg(TRACE, "failed to configure (%d) ARP offload err = %d\n",
+ enable, err);
+ err = 0;
+ } else
+ brcmf_dbg(TRACE, "successfully configured (%d) ARP offload to 0x%x\n",
+ enable, mode);
+ }
+
+ return err;
+}
+
static struct wireless_dev *brcmf_cfg80211_add_iface(struct wiphy *wiphy,
const char *name,
enum nl80211_iftype type,
}
pm = enabled ? PM_FAST : PM_OFF;
+ /* Do not enable the power save after assoc if it is a p2p interface */
+ if (ifp->vif->wdev.iftype == NL80211_IFTYPE_P2P_CLIENT) {
+ brcmf_dbg(INFO, "Do not enable power save for P2P clients\n");
+ pm = PM_OFF;
+ }
brcmf_dbg(INFO, "power save %s\n", (pm ? "enabled" : "disabled"));
err = brcmf_fil_cmd_int_set(ifp, BRCMF_C_SET_PM, pm);
return err;
}
+static s32
+brcmf_cfg80211_set_channel(struct brcmf_cfg80211_info *cfg,
+ struct brcmf_if *ifp,
+ struct ieee80211_channel *channel)
+{
+ u16 chanspec;
+ s32 err;
+
+ brcmf_dbg(TRACE, "band=%d, center_freq=%d\n", channel->band,
+ channel->center_freq);
+
+ chanspec = channel_to_chanspec(&cfg->d11inf, channel);
+ err = brcmf_fil_iovar_int_set(ifp, "chanspec", chanspec);
+
+ return err;
+}
+
static s32
brcmf_cfg80211_start_ap(struct wiphy *wiphy, struct net_device *ndev,
struct cfg80211_ap_settings *settings)
{
s32 ie_offset;
+ struct brcmf_cfg80211_info *cfg = wiphy_to_cfg(wiphy);
struct brcmf_if *ifp = netdev_priv(ndev);
struct brcmf_tlv *ssid_ie;
struct brcmf_ssid_le ssid_le;
}
brcmf_set_mpc(ifp, 0);
+ brcmf_configure_arp_offload(ifp, false);
/* find the RSN_IE */
rsn_ie = brcmf_parse_tlvs((u8 *)settings->beacon.tail,
brcmf_config_ap_mgmt_ie(ifp->vif, &settings->beacon);
+ err = brcmf_cfg80211_set_channel(cfg, ifp, settings->chandef.chan);
+ if (err < 0) {
+ brcmf_err("Set Channel failed, %d\n", err);
+ goto exit;
+ }
+
if (settings->beacon_interval) {
err = brcmf_fil_cmd_int_set(ifp, BRCMF_C_SET_BCNPRD,
settings->beacon_interval);
set_bit(BRCMF_VIF_STATUS_AP_CREATED, &ifp->vif->sme_state);
exit:
- if (err)
+ if (err) {
brcmf_set_mpc(ifp, 1);
+ brcmf_configure_arp_offload(ifp, true);
+ }
return err;
}
brcmf_err("bss_enable config failed %d\n", err);
}
brcmf_set_mpc(ifp, 1);
+ brcmf_configure_arp_offload(ifp, true);
set_bit(BRCMF_VIF_STATUS_AP_CREATING, &ifp->vif->sme_state);
clear_bit(BRCMF_VIF_STATUS_AP_CREATED, &ifp->vif->sme_state);
.types = BIT(NL80211_IFTYPE_P2P_CLIENT) |
BIT(NL80211_IFTYPE_P2P_GO)
},
+ {
+ .max = 1,
+ .types = BIT(NL80211_IFTYPE_P2P_DEVICE)
+ }
};
static const struct ieee80211_iface_combination brcmf_iface_combos[] = {
{
.max_interfaces = BRCMF_IFACE_MAX_CNT,
- .num_different_channels = 1, /* no multi-channel for now */
+ .num_different_channels = 2,
.n_limits = ARRAY_SIZE(brcmf_iface_limits),
.limits = brcmf_iface_limits
}
BIT(NL80211_IFTYPE_ADHOC) |
BIT(NL80211_IFTYPE_AP) |
BIT(NL80211_IFTYPE_P2P_CLIENT) |
- BIT(NL80211_IFTYPE_P2P_GO);
+ BIT(NL80211_IFTYPE_P2P_GO) |
+ BIT(NL80211_IFTYPE_P2P_DEVICE);
wiphy->iface_combinations = brcmf_iface_combos;
wiphy->n_iface_combinations = ARRAY_SIZE(brcmf_iface_combos);
wiphy->bands[IEEE80211_BAND_2GHZ] = &__wl_band_2ghz;
return vif;
}
-void brcmf_free_vif(struct brcmf_cfg80211_vif *vif)
+void brcmf_free_vif(struct brcmf_cfg80211_info *cfg,
+ struct brcmf_cfg80211_vif *vif)
{
- struct brcmf_cfg80211_info *cfg;
- struct wiphy *wiphy;
-
- wiphy = vif->wdev.wiphy;
- cfg = wiphy_priv(wiphy);
list_del(&vif->list);
cfg->vif_cnt--;
kfree(vif);
if (!cfg->vif_cnt) {
- wiphy_unregister(wiphy);
- wiphy_free(wiphy);
+ wiphy_unregister(cfg->wiphy);
+ wiphy_free(cfg->wiphy);
}
}
return 0;
case BRCMF_E_IF_DEL:
- ifp->vif = NULL;
mutex_unlock(&event->vif_event_lock);
/* event may not be upon user request */
if (brcmf_cfg80211_vif_event_armed(cfg))
wl_deinit_priv(cfg);
cfg80211_attach_out:
- brcmf_free_vif(vif);
- wiphy_free(wiphy);
+ brcmf_free_vif(cfg, vif);
return NULL;
}
wl_deinit_priv(cfg);
brcmf_btcoex_detach(cfg);
list_for_each_entry_safe(vif, tmp, &cfg->vif_list, list) {
- brcmf_free_vif(vif);
+ brcmf_free_vif(cfg, vif);
}
}
if (err)
goto default_conf_out;
+ brcmf_configure_arp_offload(ifp, true);
+
cfg->dongle_up = true;
default_conf_out:
struct brcmf_cfg80211_vif *brcmf_alloc_vif(struct brcmf_cfg80211_info *cfg,
enum nl80211_iftype type,
bool pm_block);
-void brcmf_free_vif(struct brcmf_cfg80211_vif *vif);
+void brcmf_free_vif(struct brcmf_cfg80211_info *cfg,
+ struct brcmf_cfg80211_vif *vif);
s32 brcmf_vif_set_mgmt_ie(struct brcmf_cfg80211_vif *vif, s32 pktflag,
const u8 *vndr_ie_buf, u32 vndr_ie_len);
}
EXPORT_SYMBOL(il_setup_rx_scan_handlers);
-inline u16
+u16
il_get_active_dwell_time(struct il_priv *il, enum ieee80211_band band,
u8 n_probes)
{
memcpy(&lq, priv->stations[i].lq,
sizeof(struct iwl_link_quality_cmd));
- if (!memcmp(&lq, &zero_lq, sizeof(lq)))
+ if (memcmp(&lq, &zero_lq, sizeof(lq)))
send_lq = true;
}
spin_unlock_bh(&priv->sta_lock);
REPLY_DEBUG_CMD = 0xf0,
DEBUG_LOG_MSG = 0xf7,
+ MCAST_FILTER_CMD = 0xd0,
+
/* D3 commands/notifications */
D3_CONFIG_CMD = 0xd3,
PROT_OFFLOAD_CONFIG_CMD = 0xd4,
u8 data[0];
} __packed; /* PHY_CALIB_OVERRIDE_VALUES_S */
+#define MAX_PORT_ID_NUM 2
+
+/**
+ * struct iwl_mcast_filter_cmd - configure multicast filter.
+ * @filter_own: Set 1 to filter out multicast packets sent by station itself
+ * @port_id: Multicast MAC addresses array specifier. This is a strange way
+ * to identify network interface adopted in host-device IF.
+ * It is used by FW as index in array of addresses. This array has
+ * MAX_PORT_ID_NUM members.
+ * @count: Number of MAC addresses in the array
+ * @pass_all: Set 1 to pass all multicast packets.
+ * @bssid: current association BSSID.
+ * @addr_list: Place holder for array of MAC addresses.
+ * IMPORTANT: add padding if necessary to ensure DWORD alignment.
+ */
+struct iwl_mcast_filter_cmd {
+ u8 filter_own;
+ u8 port_id;
+ u8 count;
+ u8 pass_all;
+ u8 bssid[6];
+ u8 reserved[2];
+ u8 addr_list[0];
+} __packed; /* MCAST_FILTERING_CMD_API_S_VER_1 */
+
#endif /* __fw_api_h__ */
*/
static void iwl_mvm_mac_ctxt_cmd_fill_sta(struct iwl_mvm *mvm,
struct ieee80211_vif *vif,
- struct iwl_mac_data_sta *ctxt_sta)
+ struct iwl_mac_data_sta *ctxt_sta,
+ bool force_assoc_off)
{
/* We need the dtim_period to set the MAC as associated */
- if (vif->bss_conf.assoc && vif->bss_conf.dtim_period) {
+ if (vif->bss_conf.assoc && vif->bss_conf.dtim_period &&
+ !force_assoc_off) {
u32 dtim_offs;
/*
cmd.filter_flags &= ~cpu_to_le32(MAC_FILTER_IN_BEACON);
/* Fill the data specific for station mode */
- iwl_mvm_mac_ctxt_cmd_fill_sta(mvm, vif, &cmd.sta);
+ iwl_mvm_mac_ctxt_cmd_fill_sta(mvm, vif, &cmd.sta,
+ action == FW_CTXT_ACTION_ADD);
return iwl_mvm_mac_ctxt_send_cmd(mvm, &cmd);
}
iwl_mvm_mac_ctxt_cmd_common(mvm, vif, &cmd, action);
/* Fill the data specific for station mode */
- iwl_mvm_mac_ctxt_cmd_fill_sta(mvm, vif, &cmd.p2p_sta.sta);
+ iwl_mvm_mac_ctxt_cmd_fill_sta(mvm, vif, &cmd.p2p_sta.sta,
+ action == FW_CTXT_ACTION_ADD);
cmd.p2p_sta.ctwin = cpu_to_le32(noa->oppps_ctwindow &
IEEE80211_P2P_OPPPS_CTWINDOW_MASK);
*total_flags = 0;
}
+static int iwl_mvm_configure_mcast_filter(struct iwl_mvm *mvm,
+ struct ieee80211_vif *vif)
+{
+ struct iwl_mcast_filter_cmd mcast_filter_cmd = {
+ .pass_all = 1,
+ };
+
+ memcpy(mcast_filter_cmd.bssid, vif->bss_conf.bssid, ETH_ALEN);
+
+ return iwl_mvm_send_cmd_pdu(mvm, MCAST_FILTER_CMD, CMD_SYNC,
+ sizeof(mcast_filter_cmd),
+ &mcast_filter_cmd);
+}
+
static void iwl_mvm_bss_info_changed_station(struct iwl_mvm *mvm,
struct ieee80211_vif *vif,
struct ieee80211_bss_conf *bss_conf,
return;
}
iwl_mvm_bt_coex_vif_assoc(mvm, vif);
+ iwl_mvm_configure_mcast_filter(mvm, vif);
} else if (mvmvif->ap_sta_id != IWL_MVM_STATION_COUNT) {
/* remove AP station now that the MAC is unassoc */
ret = iwl_mvm_rm_sta_id(mvm, vif, mvmvif->ap_sta_id);
switch (cmd) {
case STA_NOTIFY_SLEEP:
- if (atomic_read(&mvmsta->pending_frames) > 0)
+ if (atomic_read(&mvm->pending_frames[mvmsta->sta_id]) > 0)
ieee80211_sta_block_awake(hw, sta, true);
/*
* The fw updates the STA to be asleep. Tx packets on the Tx
struct ieee80211_sta __rcu *fw_id_to_mac_id[IWL_MVM_STATION_COUNT];
struct work_struct sta_drained_wk;
unsigned long sta_drained[BITS_TO_LONGS(IWL_MVM_STATION_COUNT)];
+ atomic_t pending_frames[IWL_MVM_STATION_COUNT];
/* configured by mac80211 */
u32 rts_threshold;
CMD(BT_COEX_PROT_ENV),
CMD(BT_PROFILE_NOTIFICATION),
CMD(BT_CONFIG),
+ CMD(MCAST_FILTER_CMD),
};
#undef CMD
else
cmd->type = cpu_to_le32(SCAN_TYPE_FORCED);
+ /*
+ * TODO: This is a WA due to a bug in the FW AUX framework that does not
+ * properly handle time events that fail to be scheduled
+ */
+ cmd->type = cpu_to_le32(SCAN_TYPE_FORCED);
+
cmd->repeats = cpu_to_le32(1);
/*
mvm_sta->max_agg_bufsize = LINK_QUAL_AGG_FRAME_LIMIT_DEF;
/* HW restart, don't assume the memory has been zeroed */
- atomic_set(&mvm_sta->pending_frames, 0);
+ atomic_set(&mvm->pending_frames[sta_id], 0);
mvm_sta->tid_disable_agg = 0;
mvm_sta->tfd_queue_msk = 0;
for (i = 0; i < IEEE80211_NUM_ACS; i++)
mvmvif->ap_sta_id = IWL_MVM_STATION_COUNT;
}
+ /*
+ * Make sure that the tx response code sees the station as -EBUSY and
+ * calls the drain worker.
+ */
+ spin_lock_bh(&mvm_sta->lock);
/*
* There are frames pending on the AC queues for this station.
* We need to wait until all the frames are drained...
*/
- if (atomic_read(&mvm_sta->pending_frames)) {
- ret = iwl_mvm_drain_sta(mvm, mvm_sta, true);
+ if (atomic_read(&mvm->pending_frames[mvm_sta->sta_id])) {
rcu_assign_pointer(mvm->fw_id_to_mac_id[mvm_sta->sta_id],
ERR_PTR(-EBUSY));
+ spin_unlock_bh(&mvm_sta->lock);
+ ret = iwl_mvm_drain_sta(mvm, mvm_sta, true);
} else {
+ spin_unlock_bh(&mvm_sta->lock);
ret = iwl_mvm_rm_sta_common(mvm, mvm_sta->sta_id);
rcu_assign_pointer(mvm->fw_id_to_mac_id[mvm_sta->sta_id], NULL);
}
* @bt_reduced_txpower: is reduced tx power enabled for this station
* @lock: lock to protect the whole struct. Since %tid_data is access from Tx
* and from Tx response flow, it needs a spinlock.
- * @pending_frames: number of frames for this STA on the shared Tx queues.
* @tid_data: per tid data. Look at %iwl_mvm_tid_data.
*
* When mac80211 creates a station it reserves some space (hw->sta_data_size)
u8 max_agg_bufsize;
bool bt_reduced_txpower;
spinlock_t lock;
- atomic_t pending_frames;
struct iwl_mvm_tid_data tid_data[IWL_MAX_TID_COUNT];
struct iwl_lq_sta lq_sta;
struct ieee80211_vif *vif;
spin_unlock(&mvmsta->lock);
- if (mvmsta->vif->type == NL80211_IFTYPE_AP &&
- txq_id < IWL_MVM_FIRST_AGG_QUEUE)
- atomic_inc(&mvmsta->pending_frames);
+ if (txq_id < IWL_MVM_FIRST_AGG_QUEUE)
+ atomic_inc(&mvm->pending_frames[mvmsta->sta_id]);
return 0;
/*
* If the txq is not an AMPDU queue, there is no chance we freed
* several skbs. Check that out...
- * If there are no pending frames for this STA, notify mac80211 that
- * this station can go to sleep in its STA table.
*/
- if (txq_id < IWL_MVM_FIRST_AGG_QUEUE && mvmsta &&
- !WARN_ON(skb_freed > 1) &&
- mvmsta->vif->type == NL80211_IFTYPE_AP &&
- atomic_sub_and_test(skb_freed, &mvmsta->pending_frames)) {
- ieee80211_sta_block_awake(mvm->hw, sta, false);
- set_bit(sta_id, mvm->sta_drained);
- schedule_work(&mvm->sta_drained_wk);
+ if (txq_id < IWL_MVM_FIRST_AGG_QUEUE && !WARN_ON(skb_freed > 1) &&
+ atomic_sub_and_test(skb_freed, &mvm->pending_frames[sta_id])) {
+ if (mvmsta) {
+ /*
+ * If there are no pending frames for this STA, notify
+ * mac80211 that this station can go to sleep in its
+ * STA table.
+ */
+ if (mvmsta->vif->type == NL80211_IFTYPE_AP)
+ ieee80211_sta_block_awake(mvm->hw, sta, false);
+ /*
+ * We might very well have taken mvmsta pointer while
+ * the station was being removed. The remove flow might
+ * have seen a pending_frame (because we didn't take
+ * the lock) even if now the queues are drained. So make
+ * really sure now that this the station is not being
+ * removed. If it is, run the drain worker to remove it.
+ */
+ spin_lock_bh(&mvmsta->lock);
+ sta = rcu_dereference(mvm->fw_id_to_mac_id[sta_id]);
+ if (IS_ERR_OR_NULL(sta)) {
+ /*
+ * Station disappeared in the meantime:
+ * so we are draining.
+ */
+ set_bit(sta_id, mvm->sta_drained);
+ schedule_work(&mvm->sta_drained_wk);
+ }
+ spin_unlock_bh(&mvmsta->lock);
+ } else if (!mvmsta) {
+ /* Tx response without STA, so we are draining */
+ set_bit(sta_id, mvm->sta_drained);
+ schedule_work(&mvm->sta_drained_wk);
+ }
}
rcu_read_unlock();
class_destroy(hwsim_class);
}
-
-static struct device_driver mac80211_hwsim_driver = {
- .name = "mac80211_hwsim",
- .bus = &platform_bus_type,
- .owner = THIS_MODULE,
+static struct platform_driver mac80211_hwsim_driver = {
+ .driver = {
+ .name = "mac80211_hwsim",
+ .owner = THIS_MODULE,
+ },
};
static const struct net_device_ops hwsim_netdev_ops = {
spin_lock_init(&hwsim_radio_lock);
INIT_LIST_HEAD(&hwsim_radios);
- err = driver_register(&mac80211_hwsim_driver);
+ err = platform_driver_register(&mac80211_hwsim_driver);
if (err)
return err;
err = -ENOMEM;
goto failed_drvdata;
}
- data->dev->driver = &mac80211_hwsim_driver;
+ data->dev->driver = &mac80211_hwsim_driver.driver;
err = device_bind_driver(data->dev);
if (err != 0) {
printk(KERN_DEBUG
failed:
mac80211_hwsim_free();
failed_unregister_driver:
- driver_unregister(&mac80211_hwsim_driver);
+ platform_driver_unregister(&mac80211_hwsim_driver);
return err;
}
module_init(init_mac80211_hwsim);
mac80211_hwsim_free();
unregister_netdev(hwsim_mon);
- driver_unregister(&mac80211_hwsim_driver);
+ platform_driver_unregister(&mac80211_hwsim_driver);
}
module_exit(exit_mac80211_hwsim);
rxmcs == DESC92C_RATE11M)
struct phy_rx_agc_info_t {
- #if __LITTLE_ENDIAN
+ #ifdef __LITTLE_ENDIAN
u8 gain:7, trsw:1;
#else
u8 trsw:1, gain:7;
u8 stream_target_csi[2];
u8 sig_evm;
u8 rsvd_3;
-#if __LITTLE_ENDIAN
+#ifdef __LITTLE_ENDIAN
u8 antsel_rx_keep_2:1; /*ex_intf_flg:1;*/
u8 sgi_en:1;
u8 rxsc:2;
{RTL_USB_DEVICE(0x07aa, 0x0056, rtl92cu_hal_cfg)}, /*ATKK-Gemtek*/
{RTL_USB_DEVICE(0x07b8, 0x8178, rtl92cu_hal_cfg)}, /*Funai -Abocom*/
{RTL_USB_DEVICE(0x0846, 0x9021, rtl92cu_hal_cfg)}, /*Netgear-Sercomm*/
+ {RTL_USB_DEVICE(0x0846, 0xf001, rtl92cu_hal_cfg)}, /*On Netwrks N300MA*/
{RTL_USB_DEVICE(0x0b05, 0x17ab, rtl92cu_hal_cfg)}, /*ASUS-Edimax*/
{RTL_USB_DEVICE(0x0bda, 0x8186, rtl92cu_hal_cfg)}, /*Realtek 92CE-VAU*/
{RTL_USB_DEVICE(0x0df6, 0x0061, rtl92cu_hal_cfg)}, /*Sitecom-Edimax*/
config NFC_MEI_PHY
tristate "MEI bus NFC device support"
- depends on INTEL_MEI_BUS_NFC && NFC_HCI
+ depends on INTEL_MEI && NFC_HCI
help
This adds support to use an mei bus nfc device. Select this if you
will use an HCI NFC driver for an NFC chip connected behind an
return r;
}
+ r = mei_cl_register_event_cb(phy->device, nfc_mei_event_cb, phy);
+ if (r) {
+ pr_err("MEY_PHY: Event cb registration failed\n");
+ mei_cl_disable_device(phy->device);
+ phy->powered = 0;
+
+ return r;
+ }
+
phy->powered = 1;
return 0;
return -ENOMEM;
}
- r = mei_cl_register_event_cb(device, nfc_mei_event_cb, phy);
- if (r) {
- pr_err(MICROREAD_DRIVER_NAME ": event cb registration failed\n");
- goto err_out;
- }
-
r = microread_probe(phy, &mei_phy_ops, LLC_NOP_NAME,
MEI_NFC_HEADER_SIZE, 0, MEI_NFC_MAX_HCI_PAYLOAD,
&phy->hdev);
- if (r < 0)
- goto err_out;
-
- return 0;
+ if (r < 0) {
+ nfc_mei_phy_free(phy);
-err_out:
- nfc_mei_phy_free(phy);
+ return r;
+ }
- return r;
+ return 0;
}
static int microread_mei_remove(struct mei_cl_device *device)
microread_remove(phy->hdev);
- nfc_mei_phy_disable(phy);
-
nfc_mei_phy_free(phy);
return 0;
return -ENOMEM;
}
- r = mei_cl_register_event_cb(device, nfc_mei_event_cb, phy);
- if (r) {
- pr_err(PN544_DRIVER_NAME ": event cb registration failed\n");
- goto err_out;
- }
-
r = pn544_hci_probe(phy, &mei_phy_ops, LLC_NOP_NAME,
MEI_NFC_HEADER_SIZE, 0, MEI_NFC_MAX_HCI_PAYLOAD,
&phy->hdev);
- if (r < 0)
- goto err_out;
-
- return 0;
+ if (r < 0) {
+ nfc_mei_phy_free(phy);
-err_out:
- nfc_mei_phy_free(phy);
+ return r;
+ }
- return r;
+ return 0;
}
static int pn544_mei_remove(struct mei_cl_device *device)
pn544_hci_remove(phy->hdev);
- nfc_mei_phy_disable(phy);
-
nfc_mei_phy_free(phy);
return 0;
BUG();
}
- if (ldev->hba.elmmio_space.start) {
+ if (ldev->hba.elmmio_space.flags) {
err = request_resource(&iomem_resource,
&(ldev->hba.elmmio_space));
if (err < 0) {
case PAT_LMMIO:
/* used to fix up pre-initialized MEM BARs */
- if (!lba_dev->hba.lmmio_space.start) {
+ if (!lba_dev->hba.lmmio_space.flags) {
sprintf(lba_dev->hba.lmmio_name,
"PCI%02x LMMIO",
(int)lba_dev->hba.bus_num.start);
io->start;
r = &lba_dev->hba.lmmio_space;
r->name = lba_dev->hba.lmmio_name;
- } else if (!lba_dev->hba.elmmio_space.start) {
+ } else if (!lba_dev->hba.elmmio_space.flags) {
sprintf(lba_dev->hba.elmmio_name,
"PCI%02x ELMMIO",
(int)lba_dev->hba.bus_num.start);
r->name = "LBA PCI Busses";
r->start = lba_num & 0xff;
r->end = (lba_num>>8) & 0xff;
+ r->flags = IORESOURCE_BUS;
/* Set up local PCI Bus resources - we don't need them for
** Legacy boxes but it's nice to see in /proc/iomem.
pci_add_resource_offset(&resources, &lba_dev->hba.io_space,
HBA_PORT_BASE(lba_dev->hba.hba_num));
- if (lba_dev->hba.elmmio_space.start)
+ if (lba_dev->hba.elmmio_space.flags)
pci_add_resource_offset(&resources, &lba_dev->hba.elmmio_space,
lba_dev->hba.lmmio_space_offset);
if (lba_dev->hba.lmmio_space.flags)
.probe = superio_probe,
};
-static int __init superio_modinit(void)
-{
- return pci_register_driver(&superio_driver);
-}
-
-static void __exit superio_exit(void)
-{
- pci_unregister_driver(&superio_driver);
-}
-
-module_init(superio_modinit);
-module_exit(superio_exit);
+module_pci_driver(superio_driver);
config PARPORT_PC_SUPERIO
bool "SuperIO chipset support"
- depends on PARPORT_PC
+ depends on PARPORT_PC && !PARISC
help
Saying Y here enables some probes for Super-IO chipsets in order to
find out things like base addresses, IRQ lines and DMA channels. It
struct parport *parport_gsc_probe_port(unsigned long base,
unsigned long base_hi, int irq,
- int dma, struct pci_dev *dev)
+ int dma, struct parisc_device *padev)
{
struct parport_gsc_private *priv;
struct parport_operations *ops;
priv->ctr_writable = 0xff;
priv->dma_buf = 0;
priv->dma_handle = 0;
- priv->dev = dev;
p->base = base;
p->base_hi = base_hi;
p->irq = irq;
return NULL;
}
+ p->dev = &padev->dev;
p->base_hi = base_hi;
p->modes = tmp.modes;
p->size = (p->modes & PARPORT_MODE_EPP)?8:3;
}
p = parport_gsc_probe_port(port, 0, dev->irq,
- /* PARPORT_IRQ_NONE */ PARPORT_DMA_NONE, NULL);
+ /* PARPORT_IRQ_NONE */ PARPORT_DMA_NONE, dev);
if (p)
parport_count++;
dev_set_drvdata(&dev->dev, p);
extern struct parport *parport_gsc_probe_port(unsigned long base,
unsigned long base_hi,
int irq, int dma,
- struct pci_dev *dev);
+ struct parisc_device *padev);
#endif /* __DRIVERS_PARPORT_PARPORT_GSC_H */
return AE_OK ;
}
+void acpiphp_check_host_bridge(acpi_handle handle)
+{
+ struct acpiphp_bridge *bridge;
+
+ bridge = acpiphp_handle_to_bridge(handle);
+ if (bridge) {
+ acpiphp_check_bridge(bridge);
+ put_bridge(bridge);
+ }
+
+ acpi_walk_namespace(ACPI_TYPE_DEVICE, handle,
+ ACPI_UINT32_MAX, check_sub_bridges, NULL, NULL, NULL);
+}
+
static void _handle_hotplug_event_bridge(struct work_struct *work)
{
struct acpiphp_bridge *bridge;
u8 devfn;
u16 domain;
int severity;
+ struct aer_capability_regs *regs;
};
static DEFINE_KFIFO(aer_recover_ring, struct aer_recover_entry,
static DECLARE_WORK(aer_recover_work, aer_recover_work_func);
void aer_recover_queue(int domain, unsigned int bus, unsigned int devfn,
- int severity)
+ int severity, struct aer_capability_regs *aer_regs)
{
unsigned long flags;
struct aer_recover_entry entry = {
.devfn = devfn,
.domain = domain,
.severity = severity,
+ .regs = aer_regs,
};
spin_lock_irqsave(&aer_recover_ring_lock, flags);
PCI_SLOT(entry.devfn), PCI_FUNC(entry.devfn));
continue;
}
+ cper_print_aer(pdev, entry.severity, entry.regs);
do_recovery(pdev, entry.severity);
pci_dev_put(pdev);
}
}
EXPORT_SYMBOL_GPL(cper_severity_to_aer);
-void cper_print_aer(const char *prefix, struct pci_dev *dev, int cper_severity,
+void cper_print_aer(struct pci_dev *dev, int cper_severity,
struct aer_capability_regs *aer)
{
int aer_severity, layer, agent, status_strs_size, tlp_header_valid = 0;
agent = AER_GET_AGENT(aer_severity, status);
dev_err(&dev->dev, "aer_status: 0x%08x, aer_mask: 0x%08x\n",
status, mask);
- cper_print_bits(prefix, status, status_strs, status_strs_size);
+ cper_print_bits("", status, status_strs, status_strs_size);
dev_err(&dev->dev, "aer_layer=%s, aer_agent=%s\n",
aer_error_layer[layer], aer_agent_string[agent]);
if (aer_severity != AER_CORRECTABLE)
bool found = false;
unsigned long config;
- mutex_lock(&pctldev->mutex);
+ mutex_lock(&pinctrl_maps_mutex);
/* Parse the pinctrl map and look for the elected pin/state */
for_each_maps(maps_node, i, map) {
confops->pin_config_config_dbg_show(pctldev, s, config);
exit:
- mutex_unlock(&pctldev->mutex);
+ mutex_unlock(&pinctrl_maps_mutex);
return 0;
}
return 0;
err_no_range:
- err = gpiochip_remove(&gpio->chip);
+ if (gpiochip_remove(&gpio->chip))
+ dev_err(&pdev->dev, "failed to remove gpio chip\n");
err_no_chip:
err_no_domain:
err_no_port:
return IRQ_HANDLED;
}
+struct exynos_eint_gpio_save {
+ u32 eint_con;
+ u32 eint_fltcon0;
+ u32 eint_fltcon1;
+};
+
/*
* exynos_eint_gpio_init() - setup handling of external gpio interrupts.
* @d: driver data of samsung pinctrl driver.
{
struct samsung_pin_bank *bank;
struct device *dev = d->dev;
- unsigned int ret;
- unsigned int i;
+ int ret;
+ int i;
if (!d->irq) {
dev_err(dev, "irq number not available\n");
bank->nr_pins, &exynos_gpio_irqd_ops, bank);
if (!bank->irq_domain) {
dev_err(dev, "gpio irq domain add failed\n");
- return -ENXIO;
+ ret = -ENXIO;
+ goto err_domains;
+ }
+
+ bank->soc_priv = devm_kzalloc(d->dev,
+ sizeof(struct exynos_eint_gpio_save), GFP_KERNEL);
+ if (!bank->soc_priv) {
+ irq_domain_remove(bank->irq_domain);
+ ret = -ENOMEM;
+ goto err_domains;
}
}
return 0;
+
+err_domains:
+ for (--i, --bank; i >= 0; --i, --bank) {
+ if (bank->eint_type != EINT_TYPE_GPIO)
+ continue;
+ irq_domain_remove(bank->irq_domain);
+ }
+
+ return ret;
}
static void exynos_wkup_irq_unmask(struct irq_data *irqd)
return 0;
}
+static u32 exynos_eint_wake_mask = 0xffffffff;
+
+u32 exynos_get_eint_wake_mask(void)
+{
+ return exynos_eint_wake_mask;
+}
+
+static int exynos_wkup_irq_set_wake(struct irq_data *irqd, unsigned int on)
+{
+ struct samsung_pin_bank *bank = irq_data_get_irq_chip_data(irqd);
+ unsigned long bit = 1UL << (2 * bank->eint_offset + irqd->hwirq);
+
+ pr_info("wake %s for irq %d\n", on ? "enabled" : "disabled", irqd->irq);
+
+ if (!on)
+ exynos_eint_wake_mask |= bit;
+ else
+ exynos_eint_wake_mask &= ~bit;
+
+ return 0;
+}
+
/*
* irq_chip for wakeup interrupts
*/
.irq_mask = exynos_wkup_irq_mask,
.irq_ack = exynos_wkup_irq_ack,
.irq_set_type = exynos_wkup_irq_set_type,
+ .irq_set_wake = exynos_wkup_irq_set_wake,
};
/* interrupt handler for wakeup interrupts 0..15 */
return 0;
}
+static void exynos_pinctrl_suspend_bank(
+ struct samsung_pinctrl_drv_data *drvdata,
+ struct samsung_pin_bank *bank)
+{
+ struct exynos_eint_gpio_save *save = bank->soc_priv;
+ void __iomem *regs = drvdata->virt_base;
+
+ save->eint_con = readl(regs + EXYNOS_GPIO_ECON_OFFSET
+ + bank->eint_offset);
+ save->eint_fltcon0 = readl(regs + EXYNOS_GPIO_EFLTCON_OFFSET
+ + 2 * bank->eint_offset);
+ save->eint_fltcon1 = readl(regs + EXYNOS_GPIO_EFLTCON_OFFSET
+ + 2 * bank->eint_offset + 4);
+
+ pr_debug("%s: save con %#010x\n", bank->name, save->eint_con);
+ pr_debug("%s: save fltcon0 %#010x\n", bank->name, save->eint_fltcon0);
+ pr_debug("%s: save fltcon1 %#010x\n", bank->name, save->eint_fltcon1);
+}
+
+static void exynos_pinctrl_suspend(struct samsung_pinctrl_drv_data *drvdata)
+{
+ struct samsung_pin_ctrl *ctrl = drvdata->ctrl;
+ struct samsung_pin_bank *bank = ctrl->pin_banks;
+ int i;
+
+ for (i = 0; i < ctrl->nr_banks; ++i, ++bank)
+ if (bank->eint_type == EINT_TYPE_GPIO)
+ exynos_pinctrl_suspend_bank(drvdata, bank);
+}
+
+static void exynos_pinctrl_resume_bank(
+ struct samsung_pinctrl_drv_data *drvdata,
+ struct samsung_pin_bank *bank)
+{
+ struct exynos_eint_gpio_save *save = bank->soc_priv;
+ void __iomem *regs = drvdata->virt_base;
+
+ pr_debug("%s: con %#010x => %#010x\n", bank->name,
+ readl(regs + EXYNOS_GPIO_ECON_OFFSET
+ + bank->eint_offset), save->eint_con);
+ pr_debug("%s: fltcon0 %#010x => %#010x\n", bank->name,
+ readl(regs + EXYNOS_GPIO_EFLTCON_OFFSET
+ + 2 * bank->eint_offset), save->eint_fltcon0);
+ pr_debug("%s: fltcon1 %#010x => %#010x\n", bank->name,
+ readl(regs + EXYNOS_GPIO_EFLTCON_OFFSET
+ + 2 * bank->eint_offset + 4), save->eint_fltcon1);
+
+ writel(save->eint_con, regs + EXYNOS_GPIO_ECON_OFFSET
+ + bank->eint_offset);
+ writel(save->eint_fltcon0, regs + EXYNOS_GPIO_EFLTCON_OFFSET
+ + 2 * bank->eint_offset);
+ writel(save->eint_fltcon1, regs + EXYNOS_GPIO_EFLTCON_OFFSET
+ + 2 * bank->eint_offset + 4);
+}
+
+static void exynos_pinctrl_resume(struct samsung_pinctrl_drv_data *drvdata)
+{
+ struct samsung_pin_ctrl *ctrl = drvdata->ctrl;
+ struct samsung_pin_bank *bank = ctrl->pin_banks;
+ int i;
+
+ for (i = 0; i < ctrl->nr_banks; ++i, ++bank)
+ if (bank->eint_type == EINT_TYPE_GPIO)
+ exynos_pinctrl_resume_bank(drvdata, bank);
+}
+
/* pin banks of exynos4210 pin-controller 0 */
static struct samsung_pin_bank exynos4210_pin_banks0[] = {
EXYNOS_PIN_BANK_EINTG(8, 0x000, "gpa0", 0x00),
.geint_pend = EXYNOS_GPIO_EPEND_OFFSET,
.svc = EXYNOS_SVC_OFFSET,
.eint_gpio_init = exynos_eint_gpio_init,
+ .suspend = exynos_pinctrl_suspend,
+ .resume = exynos_pinctrl_resume,
.label = "exynos4210-gpio-ctrl0",
}, {
/* pin-controller instance 1 data */
.svc = EXYNOS_SVC_OFFSET,
.eint_gpio_init = exynos_eint_gpio_init,
.eint_wkup_init = exynos_eint_wkup_init,
+ .suspend = exynos_pinctrl_suspend,
+ .resume = exynos_pinctrl_resume,
.label = "exynos4210-gpio-ctrl1",
}, {
/* pin-controller instance 2 data */
.geint_pend = EXYNOS_GPIO_EPEND_OFFSET,
.svc = EXYNOS_SVC_OFFSET,
.eint_gpio_init = exynos_eint_gpio_init,
+ .suspend = exynos_pinctrl_suspend,
+ .resume = exynos_pinctrl_resume,
.label = "exynos4x12-gpio-ctrl0",
}, {
/* pin-controller instance 1 data */
.svc = EXYNOS_SVC_OFFSET,
.eint_gpio_init = exynos_eint_gpio_init,
.eint_wkup_init = exynos_eint_wkup_init,
+ .suspend = exynos_pinctrl_suspend,
+ .resume = exynos_pinctrl_resume,
.label = "exynos4x12-gpio-ctrl1",
}, {
/* pin-controller instance 2 data */
.geint_pend = EXYNOS_GPIO_EPEND_OFFSET,
.svc = EXYNOS_SVC_OFFSET,
.eint_gpio_init = exynos_eint_gpio_init,
+ .suspend = exynos_pinctrl_suspend,
+ .resume = exynos_pinctrl_resume,
.label = "exynos4x12-gpio-ctrl2",
}, {
/* pin-controller instance 3 data */
.geint_pend = EXYNOS_GPIO_EPEND_OFFSET,
.svc = EXYNOS_SVC_OFFSET,
.eint_gpio_init = exynos_eint_gpio_init,
+ .suspend = exynos_pinctrl_suspend,
+ .resume = exynos_pinctrl_resume,
.label = "exynos4x12-gpio-ctrl3",
},
};
.svc = EXYNOS_SVC_OFFSET,
.eint_gpio_init = exynos_eint_gpio_init,
.eint_wkup_init = exynos_eint_wkup_init,
+ .suspend = exynos_pinctrl_suspend,
+ .resume = exynos_pinctrl_resume,
.label = "exynos5250-gpio-ctrl0",
}, {
/* pin-controller instance 1 data */
.geint_pend = EXYNOS_GPIO_EPEND_OFFSET,
.svc = EXYNOS_SVC_OFFSET,
.eint_gpio_init = exynos_eint_gpio_init,
+ .suspend = exynos_pinctrl_suspend,
+ .resume = exynos_pinctrl_resume,
.label = "exynos5250-gpio-ctrl1",
}, {
/* pin-controller instance 2 data */
.geint_pend = EXYNOS_GPIO_EPEND_OFFSET,
.svc = EXYNOS_SVC_OFFSET,
.eint_gpio_init = exynos_eint_gpio_init,
+ .suspend = exynos_pinctrl_suspend,
+ .resume = exynos_pinctrl_resume,
.label = "exynos5250-gpio-ctrl2",
}, {
/* pin-controller instance 3 data */
.geint_pend = EXYNOS_GPIO_EPEND_OFFSET,
.svc = EXYNOS_SVC_OFFSET,
.eint_gpio_init = exynos_eint_gpio_init,
+ .suspend = exynos_pinctrl_suspend,
+ .resume = exynos_pinctrl_resume,
.label = "exynos5250-gpio-ctrl3",
},
};
/* External GPIO and wakeup interrupt related definitions */
#define EXYNOS_GPIO_ECON_OFFSET 0x700
+#define EXYNOS_GPIO_EFLTCON_OFFSET 0x800
#define EXYNOS_GPIO_EMASK_OFFSET 0x900
#define EXYNOS_GPIO_EPEND_OFFSET 0xA00
#define EXYNOS_WKUP_ECON_OFFSET 0xE00
#include <linux/gpio.h>
#include <linux/irqdomain.h>
#include <linux/spinlock.h>
+#include <linux/syscore_ops.h>
#include "core.h"
#include "pinctrl-samsung.h"
{ "samsung,pin-pud-pdn", PINCFG_TYPE_PUD_PDN },
};
+/* Global list of devices (struct samsung_pinctrl_drv_data) */
+LIST_HEAD(drvdata_list);
+
static unsigned int pin_base;
static inline struct samsung_pin_bank *gc_to_pin_bank(struct gpio_chip *gc)
ctrl->eint_wkup_init(drvdata);
platform_set_drvdata(pdev, drvdata);
+
+ /* Add to the global list */
+ list_add_tail(&drvdata->node, &drvdata_list);
+
return 0;
}
+#ifdef CONFIG_PM
+
+/**
+ * samsung_pinctrl_suspend_dev - save pinctrl state for suspend for a device
+ *
+ * Save data for all banks handled by this device.
+ */
+static void samsung_pinctrl_suspend_dev(
+ struct samsung_pinctrl_drv_data *drvdata)
+{
+ struct samsung_pin_ctrl *ctrl = drvdata->ctrl;
+ void __iomem *virt_base = drvdata->virt_base;
+ int i;
+
+ for (i = 0; i < ctrl->nr_banks; i++) {
+ struct samsung_pin_bank *bank = &ctrl->pin_banks[i];
+ void __iomem *reg = virt_base + bank->pctl_offset;
+
+ u8 *offs = bank->type->reg_offset;
+ u8 *widths = bank->type->fld_width;
+ enum pincfg_type type;
+
+ /* Registers without a powerdown config aren't lost */
+ if (!widths[PINCFG_TYPE_CON_PDN])
+ continue;
+
+ for (type = 0; type < PINCFG_TYPE_NUM; type++)
+ if (widths[type])
+ bank->pm_save[type] = readl(reg + offs[type]);
+
+ if (widths[PINCFG_TYPE_FUNC] * bank->nr_pins > 32) {
+ /* Some banks have two config registers */
+ bank->pm_save[PINCFG_TYPE_NUM] =
+ readl(reg + offs[PINCFG_TYPE_FUNC] + 4);
+ pr_debug("Save %s @ %p (con %#010x %08x)\n",
+ bank->name, reg,
+ bank->pm_save[PINCFG_TYPE_FUNC],
+ bank->pm_save[PINCFG_TYPE_NUM]);
+ } else {
+ pr_debug("Save %s @ %p (con %#010x)\n", bank->name,
+ reg, bank->pm_save[PINCFG_TYPE_FUNC]);
+ }
+ }
+
+ if (ctrl->suspend)
+ ctrl->suspend(drvdata);
+}
+
+/**
+ * samsung_pinctrl_resume_dev - restore pinctrl state from suspend for a device
+ *
+ * Restore one of the banks that was saved during suspend.
+ *
+ * We don't bother doing anything complicated to avoid glitching lines since
+ * we're called before pad retention is turned off.
+ */
+static void samsung_pinctrl_resume_dev(struct samsung_pinctrl_drv_data *drvdata)
+{
+ struct samsung_pin_ctrl *ctrl = drvdata->ctrl;
+ void __iomem *virt_base = drvdata->virt_base;
+ int i;
+
+ if (ctrl->resume)
+ ctrl->resume(drvdata);
+
+ for (i = 0; i < ctrl->nr_banks; i++) {
+ struct samsung_pin_bank *bank = &ctrl->pin_banks[i];
+ void __iomem *reg = virt_base + bank->pctl_offset;
+
+ u8 *offs = bank->type->reg_offset;
+ u8 *widths = bank->type->fld_width;
+ enum pincfg_type type;
+
+ /* Registers without a powerdown config aren't lost */
+ if (!widths[PINCFG_TYPE_CON_PDN])
+ continue;
+
+ if (widths[PINCFG_TYPE_FUNC] * bank->nr_pins > 32) {
+ /* Some banks have two config registers */
+ pr_debug("%s @ %p (con %#010x %08x => %#010x %08x)\n",
+ bank->name, reg,
+ readl(reg + offs[PINCFG_TYPE_FUNC]),
+ readl(reg + offs[PINCFG_TYPE_FUNC] + 4),
+ bank->pm_save[PINCFG_TYPE_FUNC],
+ bank->pm_save[PINCFG_TYPE_NUM]);
+ writel(bank->pm_save[PINCFG_TYPE_NUM],
+ reg + offs[PINCFG_TYPE_FUNC] + 4);
+ } else {
+ pr_debug("%s @ %p (con %#010x => %#010x)\n", bank->name,
+ reg, readl(reg + offs[PINCFG_TYPE_FUNC]),
+ bank->pm_save[PINCFG_TYPE_FUNC]);
+ }
+ for (type = 0; type < PINCFG_TYPE_NUM; type++)
+ if (widths[type])
+ writel(bank->pm_save[type], reg + offs[type]);
+ }
+}
+
+/**
+ * samsung_pinctrl_suspend - save pinctrl state for suspend
+ *
+ * Save data for all banks across all devices.
+ */
+static int samsung_pinctrl_suspend(void)
+{
+ struct samsung_pinctrl_drv_data *drvdata;
+
+ list_for_each_entry(drvdata, &drvdata_list, node) {
+ samsung_pinctrl_suspend_dev(drvdata);
+ }
+
+ return 0;
+}
+
+/**
+ * samsung_pinctrl_resume - restore pinctrl state for suspend
+ *
+ * Restore data for all banks across all devices.
+ */
+static void samsung_pinctrl_resume(void)
+{
+ struct samsung_pinctrl_drv_data *drvdata;
+
+ list_for_each_entry_reverse(drvdata, &drvdata_list, node) {
+ samsung_pinctrl_resume_dev(drvdata);
+ }
+}
+
+#else
+#define samsung_pinctrl_suspend NULL
+#define samsung_pinctrl_resume NULL
+#endif
+
+static struct syscore_ops samsung_pinctrl_syscore_ops = {
+ .suspend = samsung_pinctrl_suspend,
+ .resume = samsung_pinctrl_resume,
+};
+
static const struct of_device_id samsung_pinctrl_dt_match[] = {
#ifdef CONFIG_PINCTRL_EXYNOS
{ .compatible = "samsung,exynos4210-pinctrl",
static int __init samsung_pinctrl_drv_register(void)
{
+ /*
+ * Register syscore ops for save/restore of registers across suspend.
+ * It's important to ensure that this driver is running at an earlier
+ * initcall level than any arch-specific init calls that install syscore
+ * ops that turn off pad retention (like exynos_pm_resume).
+ */
+ register_syscore_ops(&samsung_pinctrl_syscore_ops);
+
return platform_driver_register(&samsung_pinctrl_driver);
}
postcore_initcall(samsung_pinctrl_drv_register);
* @gpio_chip: GPIO chip of the bank.
* @grange: linux gpio pin range supported by this bank.
* @slock: spinlock protecting bank registers
+ * @pm_save: saved register values during suspend
*/
struct samsung_pin_bank {
struct samsung_pin_bank_type *type;
u32 eint_mask;
u32 eint_offset;
char *name;
+ void *soc_priv;
struct device_node *of_node;
struct samsung_pinctrl_drv_data *drvdata;
struct irq_domain *irq_domain;
struct gpio_chip gpio_chip;
struct pinctrl_gpio_range grange;
spinlock_t slock;
+
+ u32 pm_save[PINCFG_TYPE_NUM + 1]; /* +1 to handle double CON registers*/
};
/**
int (*eint_gpio_init)(struct samsung_pinctrl_drv_data *);
int (*eint_wkup_init)(struct samsung_pinctrl_drv_data *);
+ void (*suspend)(struct samsung_pinctrl_drv_data *);
+ void (*resume)(struct samsung_pinctrl_drv_data *);
+
char *label;
};
/**
* struct samsung_pinctrl_drv_data: wrapper for holding driver data together.
+ * @node: global list node
* @virt_base: register base address of the controller.
* @dev: device instance representing the controller.
* @irq: interrpt number used by the controller to notify gpio interrupts.
* @nr_function: number of such pin functions.
*/
struct samsung_pinctrl_drv_data {
+ struct list_head node;
void __iomem *virt_base;
struct device *dev;
int irq;
}
clk = devm_clk_get(&pdev->dev, NULL);
- if (IS_ERR(clk))
+ if (IS_ERR(clk)) {
+ ret = PTR_ERR(clk);
goto gpiochip_error;
+ }
clk_prepare_enable(clk);
return 0;
gpiochip_error:
- ret = gpiochip_remove(pctl->chip);
+ if (gpiochip_remove(pctl->chip))
+ dev_err(&pdev->dev, "failed to remove gpio chip\n");
pinctrl_error:
pinctrl_unregister(pctl->pctl_dev);
return ret;
return 0;
fail_range:
- err = gpiochip_remove(&data->gpio_chip);
- if (err)
+ if (gpiochip_remove(&data->gpio_chip))
dev_err(&pdev->dev, "failed to remove gpio chip\n");
fail_gpio:
pinctrl_unregister(data->pctl_dev);
}
rfkill_init_sw_state(gps_rfkill,
hp_wmi_get_sw_state(HPWMI_GPS));
- rfkill_set_hw_state(bluetooth_rfkill,
+ rfkill_set_hw_state(gps_rfkill,
hp_wmi_get_hw_state(HPWMI_GPS));
err = rfkill_register(gps_rfkill);
if (err)
config BATTERY_BQ27x00
tristate "BQ27x00 battery driver"
+ depends on I2C || I2C=n
help
Say Y here to enable support for batteries with BQ27x00 (I2C/HDQ) chips.
tristate "TI LP8788 charger driver"
depends on MFD_LP8788
depends on LP8788_ADC
+ depends on IIO
help
Say Y to enable support for the LP8788 linear charger.
MODULE_LICENSE("GPL v2");
MODULE_AUTHOR("Rajkumar kasirajan, Olivier Launay");
-MODULE_ALIAS("platform:pm2xxx-charger");
+MODULE_ALIAS("i2c:pm2xxx-charger");
MODULE_DESCRIPTION("PM2xxx charger management driver");
struct wm831x_backup *devdata = platform_get_drvdata(pdev);
power_supply_unregister(&devdata->backup);
- kfree(devdata->backup.name);
return 0;
}
chip->caps = ptp_pch_caps;
chip->ptp_clock = ptp_clock_register(&chip->caps, &pdev->dev);
-
- if (IS_ERR(chip->ptp_clock))
- return PTR_ERR(chip->ptp_clock);
+ if (IS_ERR(chip->ptp_clock)) {
+ ret = PTR_ERR(chip->ptp_clock);
+ goto err_ptp_clock_reg;
+ }
spin_lock_init(&chip->register_lock);
err_req_irq:
ptp_clock_unregister(chip->ptp_clock);
+err_ptp_clock_reg:
iounmap(chip->regs);
chip->regs = NULL;
If you are unsure about this, say N here.
+choice
+ prompt "Enumeration method"
+ depends on RAPIDIO
+ default RAPIDIO_ENUM_BASIC
+ help
+ There are different enumeration and discovery mechanisms offered
+ for RapidIO subsystem. You may select single built-in method or
+ or any number of methods to be built as modules.
+ Selecting a built-in method disables use of loadable methods.
+
+ If unsure, select Basic built-in.
+
+config RAPIDIO_ENUM_BASIC
+ tristate "Basic"
+ help
+ This option includes basic RapidIO fabric enumeration and discovery
+ mechanism similar to one described in RapidIO specification Annex 1.
+
+endchoice
+
source "drivers/rapidio/switches/Kconfig"
#
# Makefile for RapidIO interconnect services
#
-obj-y += rio.o rio-access.o rio-driver.o rio-scan.o rio-sysfs.o
+obj-y += rio.o rio-access.o rio-driver.o rio-sysfs.o
+obj-$(CONFIG_RAPIDIO_ENUM_BASIC) += rio-scan.o
obj-$(CONFIG_RAPIDIO) += switches/
obj-$(CONFIG_RAPIDIO) += devices/
u32 intval;
u32 ch_inte;
+ /* For MSI mode disable all device-level interrupts */
+ if (priv->flags & TSI721_USING_MSI)
+ iowrite32(0, priv->regs + TSI721_DEV_INTE);
+
dev_int = ioread32(priv->regs + TSI721_DEV_INT);
if (!dev_int)
return IRQ_NONE;
}
}
#endif
+
+ /* For MSI mode re-enable device-level interrupts */
+ if (priv->flags & TSI721_USING_MSI) {
+ dev_int = TSI721_DEV_INT_SR2PC_CH | TSI721_DEV_INT_SRIO |
+ TSI721_DEV_INT_SMSG_CH | TSI721_DEV_INT_BDMA_CH;
+ iowrite32(dev_int, priv->regs + TSI721_DEV_INTE);
+ }
+
return IRQ_HANDLED;
}
driver_unregister(&rdrv->driver);
}
+void rio_attach_device(struct rio_dev *rdev)
+{
+ rdev->dev.bus = &rio_bus_type;
+ rdev->dev.parent = &rio_bus;
+}
+EXPORT_SYMBOL_GPL(rio_attach_device);
+
/**
* rio_match_bus - Tell if a RIO device structure has a matching RIO driver device id structure
* @dev: the standard device structure to match against
.name = "rapidio",
.match = rio_match_bus,
.dev_attrs = rio_dev_attrs,
+ .bus_attrs = rio_bus_attrs,
.probe = rio_device_probe,
.remove = rio_device_remove,
};
#include "rio.h"
-LIST_HEAD(rio_devices);
-
static void rio_init_em(struct rio_dev *rdev);
-DEFINE_SPINLOCK(rio_global_list_lock);
-
static int next_destid = 0;
static int next_comptag = 1;
return 0;
}
-/**
- * rio_switch_init - Sets switch operations for a particular vendor switch
- * @rdev: RIO device
- * @do_enum: Enumeration/Discovery mode flag
- *
- * Searches the RIO switch ops table for known switch types. If the vid
- * and did match a switch table entry, then call switch initialization
- * routine to setup switch-specific routines.
- */
-static void rio_switch_init(struct rio_dev *rdev, int do_enum)
-{
- struct rio_switch_ops *cur = __start_rio_switch_ops;
- struct rio_switch_ops *end = __end_rio_switch_ops;
-
- while (cur < end) {
- if ((cur->vid == rdev->vid) && (cur->did == rdev->did)) {
- pr_debug("RIO: calling init routine for %s\n",
- rio_name(rdev));
- cur->init_hook(rdev, do_enum);
- break;
- }
- cur++;
- }
-
- if ((cur >= end) && (rdev->pef & RIO_PEF_STD_RT)) {
- pr_debug("RIO: adding STD routing ops for %s\n",
- rio_name(rdev));
- rdev->rswitch->add_entry = rio_std_route_add_entry;
- rdev->rswitch->get_entry = rio_std_route_get_entry;
- rdev->rswitch->clr_table = rio_std_route_clr_table;
- }
-
- if (!rdev->rswitch->add_entry || !rdev->rswitch->get_entry)
- printk(KERN_ERR "RIO: missing routing ops for %s\n",
- rio_name(rdev));
-}
-
-/**
- * rio_add_device- Adds a RIO device to the device model
- * @rdev: RIO device
- *
- * Adds the RIO device to the global device list and adds the RIO
- * device to the RIO device list. Creates the generic sysfs nodes
- * for an RIO device.
- */
-static int rio_add_device(struct rio_dev *rdev)
-{
- int err;
-
- err = device_add(&rdev->dev);
- if (err)
- return err;
-
- spin_lock(&rio_global_list_lock);
- list_add_tail(&rdev->global_list, &rio_devices);
- spin_unlock(&rio_global_list_lock);
-
- rio_create_sysfs_dev_files(rdev);
-
- return 0;
-}
-
-/**
- * rio_enable_rx_tx_port - enable input receiver and output transmitter of
- * given port
- * @port: Master port associated with the RIO network
- * @local: local=1 select local port otherwise a far device is reached
- * @destid: Destination ID of the device to check host bit
- * @hopcount: Number of hops to reach the target
- * @port_num: Port (-number on switch) to enable on a far end device
- *
- * Returns 0 or 1 from on General Control Command and Status Register
- * (EXT_PTR+0x3C)
- */
-inline int rio_enable_rx_tx_port(struct rio_mport *port,
- int local, u16 destid,
- u8 hopcount, u8 port_num) {
-#ifdef CONFIG_RAPIDIO_ENABLE_RX_TX_PORTS
- u32 regval;
- u32 ext_ftr_ptr;
-
- /*
- * enable rx input tx output port
- */
- pr_debug("rio_enable_rx_tx_port(local = %d, destid = %d, hopcount = "
- "%d, port_num = %d)\n", local, destid, hopcount, port_num);
-
- ext_ftr_ptr = rio_mport_get_physefb(port, local, destid, hopcount);
-
- if (local) {
- rio_local_read_config_32(port, ext_ftr_ptr +
- RIO_PORT_N_CTL_CSR(0),
- ®val);
- } else {
- if (rio_mport_read_config_32(port, destid, hopcount,
- ext_ftr_ptr + RIO_PORT_N_CTL_CSR(port_num), ®val) < 0)
- return -EIO;
- }
-
- if (regval & RIO_PORT_N_CTL_P_TYP_SER) {
- /* serial */
- regval = regval | RIO_PORT_N_CTL_EN_RX_SER
- | RIO_PORT_N_CTL_EN_TX_SER;
- } else {
- /* parallel */
- regval = regval | RIO_PORT_N_CTL_EN_RX_PAR
- | RIO_PORT_N_CTL_EN_TX_PAR;
- }
-
- if (local) {
- rio_local_write_config_32(port, ext_ftr_ptr +
- RIO_PORT_N_CTL_CSR(0), regval);
- } else {
- if (rio_mport_write_config_32(port, destid, hopcount,
- ext_ftr_ptr + RIO_PORT_N_CTL_CSR(port_num), regval) < 0)
- return -EIO;
- }
-#endif
- return 0;
-}
-
/**
* rio_setup_device- Allocates and sets up a RIO device
* @net: RIO network
rdev->destid);
}
- rdev->dev.bus = &rio_bus_type;
- rdev->dev.parent = &rio_bus;
+ rio_attach_device(rdev);
device_initialize(&rdev->dev);
rdev->dev.release = rio_release_dev;
/**
* rio_enum_mport- Start enumeration through a master port
* @mport: Master port to send transactions
+ * @flags: Enumeration control flags
*
* Starts the enumeration process. If somebody has enumerated our
* master port device, then give up. If not and we have an active
* link, then start recursive peer enumeration. Returns %0 if
* enumeration succeeds or %-EBUSY if enumeration fails.
*/
-int rio_enum_mport(struct rio_mport *mport)
+int rio_enum_mport(struct rio_mport *mport, u32 flags)
{
struct rio_net *net = NULL;
int rc = 0;
printk(KERN_INFO "RIO: enumerate master port %d, %s\n", mport->id,
mport->name);
+
+ /*
+ * To avoid multiple start requests (repeat enumeration is not supported
+ * by this method) check if enumeration/discovery was performed for this
+ * mport: if mport was added into the list of mports for a net exit
+ * with error.
+ */
+ if (mport->nnode.next || mport->nnode.prev)
+ return -EBUSY;
+
/* If somebody else enumerated our master port device, bail. */
if (rio_enum_host(mport) < 0) {
printk(KERN_INFO
/**
* rio_disc_mport- Start discovery through a master port
* @mport: Master port to send transactions
+ * @flags: discovery control flags
*
* Starts the discovery process. If we have an active link,
- * then wait for the signal that enumeration is complete.
+ * then wait for the signal that enumeration is complete (if wait
+ * is allowed).
* When enumeration completion is signaled, start recursive
* peer discovery. Returns %0 if discovery succeeds or %-EBUSY
* on failure.
*/
-int rio_disc_mport(struct rio_mport *mport)
+int rio_disc_mport(struct rio_mport *mport, u32 flags)
{
struct rio_net *net = NULL;
unsigned long to_end;
/* If master port has an active link, allocate net and discover peers */
if (rio_mport_is_active(mport)) {
+ if (rio_enum_complete(mport))
+ goto enum_done;
+ else if (flags & RIO_SCAN_ENUM_NO_WAIT)
+ return -EAGAIN;
+
pr_debug("RIO: wait for enumeration to complete...\n");
to_end = jiffies + CONFIG_RAPIDIO_DISC_TIMEOUT * HZ;
bail:
return -EBUSY;
}
+
+static struct rio_scan rio_scan_ops = {
+ .enumerate = rio_enum_mport,
+ .discover = rio_disc_mport,
+};
+
+static bool scan;
+module_param(scan, bool, 0);
+MODULE_PARM_DESC(scan, "Start RapidIO network enumeration/discovery "
+ "(default = 0)");
+
+/**
+ * rio_basic_attach:
+ *
+ * When this enumeration/discovery method is loaded as a module this function
+ * registers its specific enumeration and discover routines for all available
+ * RapidIO mport devices. The "scan" command line parameter controls ability of
+ * the module to start RapidIO enumeration/discovery automatically.
+ *
+ * Returns 0 for success or -EIO if unable to register itself.
+ *
+ * This enumeration/discovery method cannot be unloaded and therefore does not
+ * provide a matching cleanup_module routine.
+ */
+
+static int __init rio_basic_attach(void)
+{
+ if (rio_register_scan(RIO_MPORT_ANY, &rio_scan_ops))
+ return -EIO;
+ if (scan)
+ rio_init_mports();
+ return 0;
+}
+
+late_initcall(rio_basic_attach);
+
+MODULE_DESCRIPTION("Basic RapidIO enumeration/discovery");
+MODULE_LICENSE("GPL");
rdev->rswitch->sw_sysfs(rdev, RIO_SW_SYSFS_REMOVE);
}
}
+
+static ssize_t bus_scan_store(struct bus_type *bus, const char *buf,
+ size_t count)
+{
+ long val;
+ struct rio_mport *port = NULL;
+ int rc;
+
+ if (kstrtol(buf, 0, &val) < 0)
+ return -EINVAL;
+
+ if (val == RIO_MPORT_ANY) {
+ rc = rio_init_mports();
+ goto exit;
+ }
+
+ if (val < 0 || val >= RIO_MAX_MPORTS)
+ return -EINVAL;
+
+ port = rio_find_mport((int)val);
+
+ if (!port) {
+ pr_debug("RIO: %s: mport_%d not available\n",
+ __func__, (int)val);
+ return -EINVAL;
+ }
+
+ if (!port->nscan)
+ return -EINVAL;
+
+ if (port->host_deviceid >= 0)
+ rc = port->nscan->enumerate(port, 0);
+ else
+ rc = port->nscan->discover(port, RIO_SCAN_ENUM_NO_WAIT);
+exit:
+ if (!rc)
+ rc = count;
+
+ return rc;
+}
+
+struct bus_attribute rio_bus_attrs[] = {
+ __ATTR(scan, (S_IWUSR|S_IWGRP), NULL, bus_scan_store),
+ __ATTR_NULL
+};
#include "rio.h"
+static LIST_HEAD(rio_devices);
+static DEFINE_SPINLOCK(rio_global_list_lock);
+
static LIST_HEAD(rio_mports);
+static DEFINE_MUTEX(rio_mport_list_lock);
static unsigned char next_portid;
static DEFINE_SPINLOCK(rio_mmap_lock);
return (RIO_GET_DID(port->sys_size, result));
}
+/**
+ * rio_add_device- Adds a RIO device to the device model
+ * @rdev: RIO device
+ *
+ * Adds the RIO device to the global device list and adds the RIO
+ * device to the RIO device list. Creates the generic sysfs nodes
+ * for an RIO device.
+ */
+int rio_add_device(struct rio_dev *rdev)
+{
+ int err;
+
+ err = device_add(&rdev->dev);
+ if (err)
+ return err;
+
+ spin_lock(&rio_global_list_lock);
+ list_add_tail(&rdev->global_list, &rio_devices);
+ spin_unlock(&rio_global_list_lock);
+
+ rio_create_sysfs_dev_files(rdev);
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(rio_add_device);
+
/**
* rio_request_inb_mbox - request inbound mailbox service
* @mport: RIO master port from which to allocate the mailbox resource
return ext_ftr_ptr;
}
+EXPORT_SYMBOL_GPL(rio_mport_get_physefb);
/**
* rio_get_comptag - Begin or continue searching for a RIO device by component tag
spin_unlock(&rio_global_list_lock);
return rdev;
}
+EXPORT_SYMBOL_GPL(rio_get_comptag);
/**
* rio_set_port_lockout - Sets/clears LOCKOUT bit (RIO EM 1.3) for a switch port.
regval);
return 0;
}
+EXPORT_SYMBOL_GPL(rio_set_port_lockout);
+
+/**
+ * rio_switch_init - Sets switch operations for a particular vendor switch
+ * @rdev: RIO device
+ * @do_enum: Enumeration/Discovery mode flag
+ *
+ * Searches the RIO switch ops table for known switch types. If the vid
+ * and did match a switch table entry, then call switch initialization
+ * routine to setup switch-specific routines.
+ */
+void rio_switch_init(struct rio_dev *rdev, int do_enum)
+{
+ struct rio_switch_ops *cur = __start_rio_switch_ops;
+ struct rio_switch_ops *end = __end_rio_switch_ops;
+
+ while (cur < end) {
+ if ((cur->vid == rdev->vid) && (cur->did == rdev->did)) {
+ pr_debug("RIO: calling init routine for %s\n",
+ rio_name(rdev));
+ cur->init_hook(rdev, do_enum);
+ break;
+ }
+ cur++;
+ }
+
+ if ((cur >= end) && (rdev->pef & RIO_PEF_STD_RT)) {
+ pr_debug("RIO: adding STD routing ops for %s\n",
+ rio_name(rdev));
+ rdev->rswitch->add_entry = rio_std_route_add_entry;
+ rdev->rswitch->get_entry = rio_std_route_get_entry;
+ rdev->rswitch->clr_table = rio_std_route_clr_table;
+ }
+
+ if (!rdev->rswitch->add_entry || !rdev->rswitch->get_entry)
+ printk(KERN_ERR "RIO: missing routing ops for %s\n",
+ rio_name(rdev));
+}
+EXPORT_SYMBOL_GPL(rio_switch_init);
+
+/**
+ * rio_enable_rx_tx_port - enable input receiver and output transmitter of
+ * given port
+ * @port: Master port associated with the RIO network
+ * @local: local=1 select local port otherwise a far device is reached
+ * @destid: Destination ID of the device to check host bit
+ * @hopcount: Number of hops to reach the target
+ * @port_num: Port (-number on switch) to enable on a far end device
+ *
+ * Returns 0 or 1 from on General Control Command and Status Register
+ * (EXT_PTR+0x3C)
+ */
+int rio_enable_rx_tx_port(struct rio_mport *port,
+ int local, u16 destid,
+ u8 hopcount, u8 port_num)
+{
+#ifdef CONFIG_RAPIDIO_ENABLE_RX_TX_PORTS
+ u32 regval;
+ u32 ext_ftr_ptr;
+
+ /*
+ * enable rx input tx output port
+ */
+ pr_debug("rio_enable_rx_tx_port(local = %d, destid = %d, hopcount = "
+ "%d, port_num = %d)\n", local, destid, hopcount, port_num);
+
+ ext_ftr_ptr = rio_mport_get_physefb(port, local, destid, hopcount);
+
+ if (local) {
+ rio_local_read_config_32(port, ext_ftr_ptr +
+ RIO_PORT_N_CTL_CSR(0),
+ ®val);
+ } else {
+ if (rio_mport_read_config_32(port, destid, hopcount,
+ ext_ftr_ptr + RIO_PORT_N_CTL_CSR(port_num), ®val) < 0)
+ return -EIO;
+ }
+
+ if (regval & RIO_PORT_N_CTL_P_TYP_SER) {
+ /* serial */
+ regval = regval | RIO_PORT_N_CTL_EN_RX_SER
+ | RIO_PORT_N_CTL_EN_TX_SER;
+ } else {
+ /* parallel */
+ regval = regval | RIO_PORT_N_CTL_EN_RX_PAR
+ | RIO_PORT_N_CTL_EN_TX_PAR;
+ }
+
+ if (local) {
+ rio_local_write_config_32(port, ext_ftr_ptr +
+ RIO_PORT_N_CTL_CSR(0), regval);
+ } else {
+ if (rio_mport_write_config_32(port, destid, hopcount,
+ ext_ftr_ptr + RIO_PORT_N_CTL_CSR(port_num), regval) < 0)
+ return -EIO;
+ }
+#endif
+ return 0;
+}
+EXPORT_SYMBOL_GPL(rio_enable_rx_tx_port);
+
/**
* rio_chk_dev_route - Validate route to the specified device.
return 0;
}
+EXPORT_SYMBOL_GPL(rio_mport_chk_dev_access);
/**
* rio_chk_dev_access - Validate access to the specified device.
return RIO_GET_BLOCK_ID(reg_val);
}
}
+EXPORT_SYMBOL_GPL(rio_mport_get_efb);
/**
* rio_mport_get_feature - query for devices' extended features
return 0;
}
+EXPORT_SYMBOL_GPL(rio_mport_get_feature);
/**
* rio_get_asm - Begin or continue searching for a RIO device by vid/did/asm_vid/asm_did
#endif /* CONFIG_RAPIDIO_DMA_ENGINE */
+/**
+ * rio_find_mport - find RIO mport by its ID
+ * @mport_id: number (ID) of mport device
+ *
+ * Given a RIO mport number, the desired mport is located
+ * in the global list of mports. If the mport is found, a pointer to its
+ * data structure is returned. If no mport is found, %NULL is returned.
+ */
+struct rio_mport *rio_find_mport(int mport_id)
+{
+ struct rio_mport *port;
+
+ mutex_lock(&rio_mport_list_lock);
+ list_for_each_entry(port, &rio_mports, node) {
+ if (port->id == mport_id)
+ goto found;
+ }
+ port = NULL;
+found:
+ mutex_unlock(&rio_mport_list_lock);
+
+ return port;
+}
+
+/**
+ * rio_register_scan - enumeration/discovery method registration interface
+ * @mport_id: mport device ID for which fabric scan routine has to be set
+ * (RIO_MPORT_ANY = set for all available mports)
+ * @scan_ops: enumeration/discovery control structure
+ *
+ * Assigns enumeration or discovery method to the specified mport device (or all
+ * available mports if RIO_MPORT_ANY is specified).
+ * Returns error if the mport already has an enumerator attached to it.
+ * In case of RIO_MPORT_ANY ignores ports with valid scan routines and returns
+ * an error if was unable to find at least one available mport.
+ */
+int rio_register_scan(int mport_id, struct rio_scan *scan_ops)
+{
+ struct rio_mport *port;
+ int rc = -EBUSY;
+
+ mutex_lock(&rio_mport_list_lock);
+ list_for_each_entry(port, &rio_mports, node) {
+ if (port->id == mport_id || mport_id == RIO_MPORT_ANY) {
+ if (port->nscan && mport_id == RIO_MPORT_ANY)
+ continue;
+ else if (port->nscan)
+ break;
+
+ port->nscan = scan_ops;
+ rc = 0;
+
+ if (mport_id != RIO_MPORT_ANY)
+ break;
+ }
+ }
+ mutex_unlock(&rio_mport_list_lock);
+
+ return rc;
+}
+EXPORT_SYMBOL_GPL(rio_register_scan);
+
+/**
+ * rio_unregister_scan - removes enumeration/discovery method from mport
+ * @mport_id: mport device ID for which fabric scan routine has to be
+ * unregistered (RIO_MPORT_ANY = set for all available mports)
+ *
+ * Removes enumeration or discovery method assigned to the specified mport
+ * device (or all available mports if RIO_MPORT_ANY is specified).
+ */
+int rio_unregister_scan(int mport_id)
+{
+ struct rio_mport *port;
+
+ mutex_lock(&rio_mport_list_lock);
+ list_for_each_entry(port, &rio_mports, node) {
+ if (port->id == mport_id || mport_id == RIO_MPORT_ANY) {
+ if (port->nscan)
+ port->nscan = NULL;
+ if (mport_id != RIO_MPORT_ANY)
+ break;
+ }
+ }
+ mutex_unlock(&rio_mport_list_lock);
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(rio_unregister_scan);
+
static void rio_fixup_device(struct rio_dev *dev)
{
}
work = container_of(_work, struct rio_disc_work, work);
pr_debug("RIO: discovery work for mport %d %s\n",
work->mport->id, work->mport->name);
- rio_disc_mport(work->mport);
+ work->mport->nscan->discover(work->mport, 0);
}
int rio_init_mports(void)
* First, run enumerations and check if we need to perform discovery
* on any of the registered mports.
*/
+ mutex_lock(&rio_mport_list_lock);
list_for_each_entry(port, &rio_mports, node) {
- if (port->host_deviceid >= 0)
- rio_enum_mport(port);
- else
+ if (port->host_deviceid >= 0) {
+ if (port->nscan)
+ port->nscan->enumerate(port, 0);
+ } else
n++;
}
+ mutex_unlock(&rio_mport_list_lock);
if (!n)
goto no_disc;
}
n = 0;
+ mutex_lock(&rio_mport_list_lock);
list_for_each_entry(port, &rio_mports, node) {
- if (port->host_deviceid < 0) {
+ if (port->host_deviceid < 0 && port->nscan) {
work[n].mport = port;
INIT_WORK(&work[n].work, disc_work_handler);
queue_work(rio_wq, &work[n].work);
n++;
}
}
+ mutex_unlock(&rio_mport_list_lock);
flush_workqueue(rio_wq);
pr_debug("RIO: destroy discovery workqueue\n");
return 0;
}
-device_initcall_sync(rio_init_mports);
-
static int hdids[RIO_MAX_MPORTS + 1];
static int rio_get_hdid(int index)
port->id = next_portid++;
port->host_deviceid = rio_get_hdid(port->id);
+ port->nscan = NULL;
+ mutex_lock(&rio_mport_list_lock);
list_add_tail(&port->node, &rio_mports);
+ mutex_unlock(&rio_mport_list_lock);
return 0;
}
EXPORT_SYMBOL_GPL(rio_release_inb_mbox);
EXPORT_SYMBOL_GPL(rio_request_outb_mbox);
EXPORT_SYMBOL_GPL(rio_release_outb_mbox);
+EXPORT_SYMBOL_GPL(rio_init_mports);
#include <linux/rio.h>
#define RIO_MAX_CHK_RETRY 3
+#define RIO_MPORT_ANY (-1)
/* Functions internal to the RIO core code */
extern int rio_mport_chk_dev_access(struct rio_mport *mport, u16 destid,
u8 hopcount);
extern int rio_create_sysfs_dev_files(struct rio_dev *rdev);
-extern int rio_enum_mport(struct rio_mport *mport);
-extern int rio_disc_mport(struct rio_mport *mport);
extern int rio_std_route_add_entry(struct rio_mport *mport, u16 destid,
u8 hopcount, u16 table, u16 route_destid,
u8 route_port);
u8 hopcount, u16 table);
extern int rio_set_port_lockout(struct rio_dev *rdev, u32 pnum, int lock);
extern struct rio_dev *rio_get_comptag(u32 comp_tag, struct rio_dev *from);
+extern int rio_add_device(struct rio_dev *rdev);
+extern void rio_switch_init(struct rio_dev *rdev, int do_enum);
+extern int rio_enable_rx_tx_port(struct rio_mport *port, int local, u16 destid,
+ u8 hopcount, u8 port_num);
+extern int rio_register_scan(int mport_id, struct rio_scan *scan_ops);
+extern int rio_unregister_scan(int mport_id);
+extern void rio_attach_device(struct rio_dev *rdev);
+extern struct rio_mport *rio_find_mport(int mport_id);
/* Structures internal to the RIO core code */
extern struct device_attribute rio_dev_attrs[];
-extern spinlock_t rio_global_list_lock;
+extern struct bus_attribute rio_bus_attrs[];
extern struct rio_switch_ops __start_rio_switch_ops[];
extern struct rio_switch_ops __end_rio_switch_ops[];
}
/**
- * Balance enable_count of each GPIO and actual GPIO pin control.
+ * regulator_ena_gpio_ctrl - balance enable_count of each GPIO and actual GPIO pin control
+ * @rdev: regulator_dev structure
+ * @enable: enable GPIO at initial use?
+ *
* GPIO is enabled in case of initial use. (enable_count is 0)
* GPIO is disabled when it is not shared any more. (enable_count <= 1)
*/
/**
* regulator_set_current_limit - set regulator output current limit
* @regulator: regulator source
- * @min_uA: Minimuum supported current in uA
+ * @min_uA: Minimum supported current in uA
* @max_uA: Maximum supported current in uA
*
* Sets current sink to the desired output current. This can be set during
static int power_state_active_cnt; /* will initialize to zero */
static DEFINE_SPINLOCK(power_state_active_lock);
-int power_state_active_get(void)
-{
- unsigned long flags;
- int cnt;
-
- spin_lock_irqsave(&power_state_active_lock, flags);
- cnt = power_state_active_cnt;
- spin_unlock_irqrestore(&power_state_active_lock, flags);
-
- return cnt;
-}
-
void power_state_active_enable(void)
{
unsigned long flags;
#ifdef CONFIG_REGULATOR_DEBUG
+static int power_state_active_get(void)
+{
+ unsigned long flags;
+ int cnt;
+
+ spin_lock_irqsave(&power_state_active_lock, flags);
+ cnt = power_state_active_cnt;
+ spin_unlock_irqrestore(&power_state_active_lock, flags);
+
+ return cnt;
+}
+
static struct ux500_regulator_debug {
struct dentry *dir;
struct dentry *status_file;
break;
}
- if ((id == PALMAS_REG_SMPS6) && (id == PALMAS_REG_SMPS8))
+ if ((id == PALMAS_REG_SMPS6) || (id == PALMAS_REG_SMPS8))
ramp_delay_support = true;
if (ramp_delay_support) {
pmic->desc[id].vsel_mask = SMPS10_VSEL;
pmic->desc[id].enable_reg =
PALMAS_BASE_TO_REG(PALMAS_SMPS_BASE,
- PALMAS_SMPS10_STATUS);
+ PALMAS_SMPS10_CTRL);
pmic->desc[id].enable_mask = SMPS10_BOOST_EN;
pmic->desc[id].min_uV = 3750000;
pmic->desc[id].uV_step = 1250000;
info->irq, ret);
dev_info(&pdev->dev, "RTC CHIP NAME: %s\n", pdev->id_entry->name);
- if (pdata->rtc_delay) {
+ if (pdata && pdata->rtc_delay) {
info->lp3974_bug_workaround = true;
dev_warn(&pdev->dev, "LP3974 with RTC REGERR option."
" RTC updates will be extremely slow.\n");
struct pl031_local *ldata = dev_get_drvdata(&adev->dev);
amba_set_drvdata(adev, NULL);
- free_irq(adev->irq[0], ldata->rtc);
+ free_irq(adev->irq[0], ldata);
rtc_device_unregister(ldata->rtc);
iounmap(ldata->base);
kfree(ldata);
device->path_data.opm &= ~eventlpm;
device->path_data.ppm &= ~eventlpm;
device->path_data.npm &= ~eventlpm;
- if (oldopm && !device->path_data.opm)
- dasd_generic_last_path_gone(device);
+ if (oldopm && !device->path_data.opm) {
+ dev_warn(&device->cdev->dev,
+ "No verified channel paths remain "
+ "for the device\n");
+ DBF_DEV_EVENT(DBF_WARNING, device,
+ "%s", "last verified path gone");
+ dasd_eer_write(device, NULL, DASD_EER_NOPATH);
+ dasd_device_set_stop_bits(device,
+ DASD_STOPPED_DC_WAIT);
+ }
}
if (path_event[chp] & PE_PATH_AVAILABLE) {
device->path_data.opm &= ~eventlpm;
dump_stack();
return;
}
- target_wait_for_sess_cmds(se_sess, 0);
+ target_wait_for_sess_cmds(se_sess);
transport_deregister_session_configfs(sess->se_sess);
transport_deregister_session(sess->se_sess);
static const struct file_operations proc_scsi_fops = {
.open = proc_scsi_host_open,
+ .release = single_release,
.read = seq_read,
.llseek = seq_lseek,
.write = proc_scsi_host_write
source "drivers/staging/iio/Kconfig"
-source "drivers/staging/zram/Kconfig"
-
source "drivers/staging/zsmalloc/Kconfig"
+source "drivers/staging/zram/Kconfig"
+
source "drivers/staging/wlags49_h2/Kconfig"
source "drivers/staging/wlags49_h25/Kconfig"
}
rv = alarm_do_ioctl(file, cmd, &ts);
+ if (rv)
+ return rv;
switch (ANDROID_ALARM_BASE_CMD(cmd)) {
case ANDROID_ALARM_GET_TIME(0):
break;
}
- return rv;
+ return 0;
}
#ifdef CONFIG_COMPAT
static long alarm_compat_ioctl(struct file *file, unsigned int cmd,
}
rv = alarm_do_ioctl(file, cmd, &ts);
+ if (rv)
+ return rv;
switch (ANDROID_ALARM_BASE_CMD(cmd)) {
case ANDROID_ALARM_GET_TIME(0): /* NOTE: we modified cmd above */
break;
}
- return rv;
+ return 0;
}
#endif
* 'log->buffer' which contains the first entry readable by 'euid'
*/
static size_t get_next_entry_by_uid(struct logger_log *log,
- size_t off, uid_t euid)
+ size_t off, kuid_t euid)
{
while (off != log->w_off) {
struct logger_entry *entry;
entry = get_entry_header(log, off, &scratch);
- if (entry->euid == euid)
+ if (uid_eq(entry->euid, euid))
return off;
next_len = sizeof(struct logger_entry) + entry->len;
__s32 tid;
__s32 sec;
__s32 nsec;
- uid_t euid;
+ kuid_t euid;
char msg[0];
};
config COMEDI_NI_6527
tristate "NI 6527 support"
+ depends on HAS_DMA
select COMEDI_MITE
---help---
Enable support for the National Instruments 6527 PCI card
config COMEDI_NI_65XX
tristate "NI 65xx static dio PCI card support"
+ depends on HAS_DMA
select COMEDI_MITE
---help---
Enable support for National Instruments 65xx static dio boards.
config COMEDI_NI_660X
tristate "NI 660x counter/timer PCI card support"
+ depends on HAS_DMA
select COMEDI_NI_TIOCMD
---help---
Enable support for National Instruments PCI-6601 (ni_660x), PCI-6602,
config COMEDI_NI_670X
tristate "NI 670x PCI card support"
+ depends on HAS_DMA
select COMEDI_MITE
---help---
Enable support for National Instruments PCI-6703 and PCI-6704
config COMEDI_NI_LABPC_PCI
tristate "NI Lab-PC PCI-1200 support"
+ depends on HAS_DMA
select COMEDI_NI_LABPC
select COMEDI_MITE
---help---
config COMEDI_NI_PCIDIO
tristate "NI PCI-DIO32HS, PCI-6533, PCI-6534 support"
+ depends on HAS_DMA
select COMEDI_MITE
select COMEDI_8255
---help---
config COMEDI_NI_PCIMIO
tristate "NI PCI-MIO-E series and M series support"
+ depends on HAS_DMA
select COMEDI_NI_TIOCMD
select COMEDI_8255
select COMEDI_FC
called ssv_dnp.
config COMEDI_MITE
+ depends on HAS_DMA
tristate
config COMEDI_NI_TIOCMD
tristate
+ depends on HAS_DMA
select COMEDI_NI_TIO
select COMEDI_MITE
clear_bit(PG_reserved,
&(virt_to_page(buf->virt_addr)->flags));
if (s->async_dma_dir != DMA_NONE) {
+#ifdef CONFIG_HAS_DMA
dma_free_coherent(dev->hw_dev,
PAGE_SIZE,
buf->virt_addr,
buf->dma_addr);
+#endif
} else {
free_page((unsigned long)buf->virt_addr);
}
struct comedi_buf_page *buf;
unsigned i;
+ if (!IS_ENABLED(CONFIG_HAS_DMA) && s->async_dma_dir != DMA_NONE) {
+ dev_err(dev->class_dev,
+ "dma buffer allocation not supported\n");
+ return;
+ }
+
async->buf_page_list = vzalloc(sizeof(*buf) * n_pages);
if (async->buf_page_list)
pages = vmalloc(sizeof(struct page *) * n_pages);
for (i = 0; i < n_pages; i++) {
buf = &async->buf_page_list[i];
if (s->async_dma_dir != DMA_NONE)
+#ifdef CONFIG_HAS_DMA
buf->virt_addr = dma_alloc_coherent(dev->hw_dev,
PAGE_SIZE,
&buf->dma_addr,
GFP_KERNEL |
__GFP_COMP);
+#else
+ break;
+#endif
else
buf->virt_addr = (void *)get_zeroed_page(GFP_KERNEL);
if (!buf->virt_addr)
return -EBUSY;
}
- if (!async->prealloc_buf)
- return -EINVAL;
-
/* make sure buffer is an integral number of pages
* (we round up) */
new_size = (new_size + PAGE_SIZE - 1) & PAGE_MASK;
/* clear flip-flop to make sure 2-byte registers for
* count and address get set correctly */
clear_dma_ff(devpriv->dma_chan);
- set_dma_addr(devpriv->dma_chan,
- virt_to_bus(devpriv->dma_buffer));
+ set_dma_addr(devpriv->dma_chan, devpriv->dma_addr);
/* set appropriate size of transfer */
devpriv->dma_transfer_size = labpc_suggest_transfer_size(cmd);
if (cmd->stop_src == TRIG_COUNT &&
devpriv->count -= num_points;
/* set address and count for next transfer */
- set_dma_addr(devpriv->dma_chan, virt_to_bus(devpriv->dma_buffer));
+ set_dma_addr(devpriv->dma_chan, devpriv->dma_addr);
set_dma_count(devpriv->dma_chan, leftover * sample_size);
release_dma_lock(flags);
unsigned long dma_flags;
devpriv->dma_chan = dma_chan;
+ devpriv->dma_addr =
+ virt_to_bus(devpriv->dma_buffer);
+
dma_flags = claim_dma_lock();
disable_dma(devpriv->dma_chan);
set_dma_mode(devpriv->dma_chan, DMA_MODE_READ);
unsigned int divisor_b1;
unsigned int dma_chan; /* dma channel to use */
u16 *dma_buffer; /* buffer ai will dma into */
+ phys_addr_t dma_addr;
/* transfer size in bytes for current transfer */
unsigned int dma_transfer_size;
/* we are using dma/fifo-half-full/etc. */
static int ni_gpct_insn_config(struct comedi_device *dev,
struct comedi_subdevice *s,
struct comedi_insn *insn, unsigned int *data);
+#ifdef PCIDMA
static int ni_gpct_cmd(struct comedi_device *dev, struct comedi_subdevice *s);
static int ni_gpct_cmdtest(struct comedi_device *dev,
struct comedi_subdevice *s, struct comedi_cmd *cmd);
+#endif
static int ni_gpct_cancel(struct comedi_device *dev,
struct comedi_subdevice *s);
static void handle_gpct_interrupt(struct comedi_device *dev,
for (j = 0; j < NUM_GPCT; ++j) {
s = &dev->subdevices[NI_GPCT_SUBDEV(j)];
s->type = COMEDI_SUBD_COUNTER;
- s->subdev_flags =
- SDF_READABLE | SDF_WRITABLE | SDF_LSAMPL | SDF_CMD_READ
- /* | SDF_CMD_WRITE */ ;
+ s->subdev_flags = SDF_READABLE | SDF_WRITABLE | SDF_LSAMPL;
s->n_chan = 3;
if (board->reg_type & ni_reg_m_series_mask)
s->maxdata = 0xffffffff;
s->insn_read = &ni_gpct_insn_read;
s->insn_write = &ni_gpct_insn_write;
s->insn_config = &ni_gpct_insn_config;
+#ifdef PCIDMA
+ s->subdev_flags |= SDF_CMD_READ /* | SDF_CMD_WRITE */;
s->do_cmd = &ni_gpct_cmd;
s->len_chanlist = 1;
s->do_cmdtest = &ni_gpct_cmdtest;
s->cancel = &ni_gpct_cancel;
s->async_dma_dir = DMA_BIDIRECTIONAL;
+#endif
s->private = &devpriv->counter_dev->counters[j];
devpriv->counter_dev->counters[j].chip_index = 0;
return ni_tio_winsn(counter, insn, data);
}
+#ifdef PCIDMA
static int ni_gpct_cmd(struct comedi_device *dev, struct comedi_subdevice *s)
{
int retval;
-#ifdef PCIDMA
struct ni_gpct *counter = s->private;
/* const struct comedi_cmd *cmd = &s->async->cmd; */
ni_tio_acknowledge_and_confirm(counter, NULL, NULL, NULL, NULL);
ni_e_series_enable_second_irq(dev, counter->counter_index, 1);
retval = ni_tio_cmd(counter, s->async);
-#else
- retval = -ENOTSUPP;
-#endif
return retval;
}
+#endif
+#ifdef PCIDMA
static int ni_gpct_cmdtest(struct comedi_device *dev,
struct comedi_subdevice *s, struct comedi_cmd *cmd)
{
-#ifdef PCIDMA
struct ni_gpct *counter = s->private;
return ni_tio_cmdtest(counter, cmd);
-#else
return -ENOTSUPP;
-#endif
}
+#endif
static int ni_gpct_cancel(struct comedi_device *dev, struct comedi_subdevice *s)
{
tristate "DesignWare USB2 DRD Core Support"
depends on USB
depends on VIRT_TO_BUS
- select USB_OTG_UTILS
help
Say Y or M here if your system has a Dual Role HighSpeed
USB controller based on the DesignWare HSOTG IP Core.
bool "Enable Missed SOF Tracking"
help
Say Y here to enable logging of missed SOF events to the dmesg log.
+ WARNING: This feature is still experimental.
If in doubt, say N.
config USB_DWC2_DEBUG_PERIODIC
/* Set device flags indicating whether the HCD supports DMA */
if (hsotg->core_params->dma_enable > 0) {
- if (dma_set_mask(hsotg->dev, DMA_BIT_MASK(31)) < 0)
- dev_warn(hsotg->dev,
- "can't enable workaround for >2GB RAM\n");
+ if (dma_set_mask(hsotg->dev, DMA_BIT_MASK(32)) < 0)
+ dev_warn(hsotg->dev, "can't set DMA mask\n");
if (dma_set_coherent_mask(hsotg->dev, DMA_BIT_MASK(31)) < 0)
dev_warn(hsotg->dev,
"can't enable workaround for >2GB RAM\n");
static void dwc2_track_missed_sofs(struct dwc2_hsotg *hsotg)
{
#ifdef CONFIG_USB_DWC2_TRACK_MISSED_SOFS
-#warning Compiling code to track missed SOFs
-
u16 curr_frame_number = hsotg->frame_number;
if (hsotg->frame_num_idx < FRAME_NUM_ARRAY_SIZE) {
hsotg->dev = &dev->dev;
+ /*
+ * Use reasonable defaults so platforms don't have to provide these.
+ */
+ if (!dev->dev.dma_mask)
+ dev->dev.dma_mask = &dev->dev.coherent_dma_mask;
+ if (!dev->dev.coherent_dma_mask)
+ dev->dev.coherent_dma_mask = DMA_BIT_MASK(32);
+
irq = platform_get_irq(dev, 0);
if (irq < 0) {
dev_err(&dev->dev, "missing IRQ resource\n");
config WIMAX_GDM72XX_USB_PM
bool "Enable power managerment support"
- depends on USB_SUSPEND
+ depends on PM_RUNTIME
endif # WIMAX_GDM72XX_USB
static int mxs_lradc_buffer_preenable(struct iio_dev *iio)
{
struct mxs_lradc *lradc = iio_priv(iio);
- struct iio_buffer *buffer = iio->buffer;
int ret = 0, chan, ofs = 0;
unsigned long enable = 0;
uint32_t ctrl4_set = 0;
uint32_t ctrl1_irq = 0;
const uint32_t chan_value = LRADC_CH_ACCUMULATE |
((LRADC_DELAY_TIMER_LOOP - 1) << LRADC_CH_NUM_SAMPLES_OFFSET);
- const int len = bitmap_weight(buffer->scan_mask, LRADC_MAX_TOTAL_CHANS);
+ const int len = bitmap_weight(iio->active_scan_mask, LRADC_MAX_TOTAL_CHANS);
if (!len)
return -EINVAL;
lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
writel(0xff, lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
- for_each_set_bit(chan, buffer->scan_mask, LRADC_MAX_TOTAL_CHANS) {
+ for_each_set_bit(chan, iio->active_scan_mask, LRADC_MAX_TOTAL_CHANS) {
ctrl4_set |= chan << LRADC_CTRL4_LRADCSELECT_OFFSET(ofs);
ctrl4_clr |= LRADC_CTRL4_LRADCSELECT_MASK(ofs);
ctrl1_irq |= LRADC_CTRL1_LRADC_IRQ_EN(ofs);
dev_info(&chip->client->dev,
"%s: i2c device found does not match expected id\n",
__func__);
+ ret = -EINVAL;
goto fail1;
}
if (ret) {
dev_err(&clientp->dev,
"%s: irq request failed", __func__);
- goto fail2;
+ goto fail1;
}
}
if (ret) {
dev_err(&clientp->dev,
"%s: iio registration failed\n", __func__);
- goto fail1;
+ goto fail2;
}
dev_info(&clientp->dev, "%s Light sensor found.\n", id->name);
return 0;
-fail1:
+fail2:
if (clientp->irq)
free_irq(clientp->irq, indio_dev);
-fail2:
+fail1:
iio_device_free(indio_dev);
return ret;
config DRM_IMX
tristate "DRM Support for Freescale i.MX"
select DRM_KMS_HELPER
+ select VIDEOMODE_HELPERS
select DRM_GEM_CMA_HELPER
select DRM_KMS_CMA_HELPER
depends on DRM && (ARCH_MXC || ARCH_MULTIPLATFORM)
config DRM_IMX_PARALLEL_DISPLAY
tristate "Support for parallel displays"
depends on DRM_IMX
+ select VIDEOMODE_HELPERS
config DRM_IMX_TVE
tristate "Support for TV and VGA displays"
depends on DRM_IMX
+ select REGMAP_MMIO
help
Choose this to enable the internal Television Encoder (TVe)
found on i.MX53 processors.
config DRM_IMX_IPUV3_CORE
tristate "IPUv3 core support"
depends on DRM_IMX
+ depends on RESET_CONTROLLER
help
Choose this if you have a i.MX5/6 system and want
to use the IPU. This option only enables IPU base
config DRM_IMX_IPUV3
tristate "DRM Support for i.MX IPUv3"
depends on DRM_IMX
+ depends on DRM_IMX_IPUV3_CORE
help
Choose this if you have a i.MX5 or i.MX6 processor.
tve->dac_reg = devm_regulator_get(&pdev->dev, "dac");
if (!IS_ERR(tve->dac_reg)) {
regulator_set_voltage(tve->dac_reg, 2750000, 2750000);
- regulator_enable(tve->dac_reg);
+ ret = regulator_enable(tve->dac_reg);
+ if (ret)
+ return ret;
}
tve->clk = devm_clk_get(&pdev->dev, "tve");
static void ipu_crtc_handle_pageflip(struct ipu_crtc *ipu_crtc)
{
- struct drm_pending_vblank_event *e;
- struct timeval now;
unsigned long flags;
struct drm_device *drm = ipu_crtc->base.dev;
spin_lock_irqsave(&drm->event_lock, flags);
-
- e = ipu_crtc->page_flip_event;
- if (!e) {
- spin_unlock_irqrestore(&drm->event_lock, flags);
- return;
- }
-
- do_gettimeofday(&now);
- e->event.sequence = 0;
- e->event.tv_sec = now.tv_sec;
- e->event.tv_usec = now.tv_usec;
+ if (ipu_crtc->page_flip_event)
+ drm_send_vblank_event(drm, -1, ipu_crtc->page_flip_event);
ipu_crtc->page_flip_event = NULL;
-
imx_drm_crtc_vblank_put(ipu_crtc->imx_crtc);
-
- list_add_tail(&e->base.link, &e->base.file_priv->event_list);
-
- wake_up_interruptible(&e->base.file_priv->event_wait);
-
spin_unlock_irqrestore(&drm->event_lock, flags);
}
config SOLO6X10
tristate "Softlogic 6x10 MPEG codec cards"
depends on PCI && VIDEO_DEV && SND && I2C
+ depends on FONTS
select VIDEOBUF2_DMA_SG
select VIDEOBUF2_DMA_CONTIG
select SND_PCM
}
EXPORT_SYMBOL_GPL(nvec_register_notifier);
+/**
+ * nvec_unregister_notifier - Unregister a notifier with nvec
+ * @nvec: A &struct nvec_chip
+ * @nb: The notifier block to unregister
+ *
+ * Unregisters a notifier with @nvec. The notifier will be removed from the
+ * atomic notifier chain.
+ */
+int nvec_unregister_notifier(struct nvec_chip *nvec, struct notifier_block *nb)
+{
+ return atomic_notifier_chain_unregister(&nvec->notifier_list, nb);
+}
+EXPORT_SYMBOL_GPL(nvec_unregister_notifier);
+
/**
* nvec_status_notifier - The final notifier
*
*
* Free the given message
*/
-inline void nvec_msg_free(struct nvec_chip *nvec, struct nvec_msg *msg)
+void nvec_msg_free(struct nvec_chip *nvec, struct nvec_msg *msg)
{
if (msg != &nvec->tx_scratch)
dev_vdbg(nvec->dev, "INFO: Free %ti\n", msg - nvec->msg_pool);
return -ENODEV;
}
- i2c_clk = clk_get(&pdev->dev, "div-clk");
+ i2c_clk = devm_clk_get(&pdev->dev, "div-clk");
if (IS_ERR(i2c_clk)) {
dev_err(nvec->dev, "failed to get controller clock\n");
return -ENODEV;
nvec_toggle_global_events(nvec, false);
mfd_remove_devices(nvec->dev);
+ nvec_unregister_notifier(nvec, &nvec->nvec_status_notifier);
cancel_work_sync(&nvec->rx_work);
cancel_work_sync(&nvec->tx_work);
+ /* FIXME: needs check wether nvec is responsible for power off */
+ pm_power_off = NULL;
return 0;
}
struct notifier_block *nb,
unsigned int events);
-extern int nvec_unregister_notifier(struct device *dev,
- struct notifier_block *nb,
- unsigned int events);
+extern int nvec_unregister_notifier(struct nvec_chip *dev,
+ struct notifier_block *nb);
extern void nvec_msg_free(struct nvec_chip *nvec, struct nvec_msg *msg);
static int nvec_kbd_remove(struct platform_device *pdev)
{
+ struct nvec_chip *nvec = dev_get_drvdata(pdev->dev.parent);
+ char disable_kbd[] = { NVEC_KBD, DISABLE_KBD },
+ uncnfg_wake_key_reporting[] = { NVEC_KBD, CNFG_WAKE_KEY_REPORTING,
+ false };
+ nvec_write_async(nvec, uncnfg_wake_key_reporting, 3);
+ nvec_write_async(nvec, disable_kbd, 2);
+ nvec_unregister_notifier(nvec, &keys_dev.notifier);
+
input_unregister_device(keys_dev.input);
- input_free_device(keys_dev.input);
return 0;
}
MODULE_AUTHOR("Marc Dietrich <marvin24@gmx.de>");
MODULE_DESCRIPTION("NVEC keyboard driver");
+MODULE_ALIAS("platform:nvec-kbd");
MODULE_LICENSE("GPL");
struct nvec_power *power = platform_get_drvdata(pdev);
cancel_delayed_work_sync(&power->poller);
+ nvec_unregister_notifier(power->nvec, &power->notifier);
switch (pdev->id) {
case AC:
power_supply_unregister(&nvec_psy);
struct serio *ser_dev;
char mouse_reset[] = { NVEC_PS2, SEND_COMMAND, PSMOUSE_RST, 3 };
- ser_dev = devm_kzalloc(&pdev->dev, sizeof(struct serio), GFP_KERNEL);
+ ser_dev = kzalloc(sizeof(struct serio), GFP_KERNEL);
if (ser_dev == NULL)
return -ENOMEM;
static int nvec_mouse_remove(struct platform_device *pdev)
{
+ struct nvec_chip *nvec = dev_get_drvdata(pdev->dev.parent);
+
+ ps2_sendcommand(ps2_dev.ser_dev, DISABLE_MOUSE);
+ ps2_stopstreaming(ps2_dev.ser_dev);
+ nvec_unregister_notifier(nvec, &ps2_dev.notifier);
serio_unregister_port(ps2_dev.ser_dev);
return 0;
MODULE_DESCRIPTION("NVEC mouse driver");
MODULE_AUTHOR("Marc Dietrich <marvin24@gmx.de>");
+MODULE_ALIAS("platform:nvec-mouse");
MODULE_LICENSE("GPL");
config DX_SEP
tristate "Discretix SEP driver"
- depends on PCI
+ depends on PCI && CRYPTO
help
Discretix SEP driver; used for the security processor subsystem
on board the Intel Mobile Internet Device and adds SEP availability
unsigned char intr_status;
struct synaptics_rmi4_data *rmi4_data = dev_get_drvdata(dev);
- regulator_enable(rmi4_data->regulator);
+ retval = regulator_enable(rmi4_data->regulator);
+ if (retval) {
+ dev_err(dev, "Regulator enable failed (%d)\n", retval);
+ return retval;
+ }
enable_irq(rmi4_data->i2c_client->irq);
rmi4_data->touch_stopped = false;
DBG_PRT(MSG_LEVEL_DEBUG, KERN_INFO "%s: Netdevice %s unregistered\n",
pDevice->dev->name, pDevice->apdev->name);
}
- kfree(pDevice->apdev);
+ free_netdev(pDevice->apdev);
pDevice->apdev = NULL;
pDevice->bEnable8021x = false;
pDevice->bEnableHostWEP = false;
return rc;
}
+ spin_lock_irq(&pDevice->lock);
+
if (wrq->disabled) {
pDevice->ePSMode = WMAC_POWER_CAM;
PSvDisablePowerSaving(pDevice);
+ spin_unlock_irq(&pDevice->lock);
return rc;
}
if ((wrq->flags & IW_POWER_TYPE) == IW_POWER_TIMEOUT) {
pDevice->ePSMode = WMAC_POWER_FAST;
PSvEnablePowerSaving((void *)pDevice, pMgmt->wListenInterval);
}
+
+ spin_unlock_irq(&pDevice->lock);
+
switch (wrq->flags & IW_POWER_MODE) {
case IW_POWER_UNICAST_R:
DBG_PRT(MSG_LEVEL_DEBUG, KERN_INFO " SIOCSIWPOWER: IW_POWER_UNICAST_R \n");
#ifndef _ZCACHE_RAMSTER_H_
#define _ZCACHE_RAMSTER_H_
-#ifdef CONFIG_RAMSTER_MODULE
-#define CONFIG_RAMSTER
-#endif
-
#ifdef CONFIG_RAMSTER
#include "ramster/ramster.h"
#else
#include <linux/atomic.h>
#include "debug.h"
+ssize_t ramster_foreign_eph_pages;
+ssize_t ramster_foreign_pers_pages;
#ifdef CONFIG_DEBUG_FS
#include <linux/debugfs.h>
--- /dev/null
+ RAMSTER HOW-TO
+
+Author: Dan Magenheimer
+Ramster maintainer: Konrad Wilk <konrad.wilk@oracle.com>
+
+This is a HOWTO document for ramster which, as of this writing, is in
+the kernel as a subdirectory of zcache in drivers/staging, called ramster.
+(Zcache can be built with or without ramster functionality.) If enabled
+and properly configured, ramster allows memory capacity load balancing
+across multiple machines in a cluster. Further, the ramster code serves
+as an example of asynchronous access for zcache (as well as cleancache and
+frontswap) that may prove useful for future transcendent memory
+implementations, such as KVM and NVRAM. While ramster works today on
+any network connection that supports kernel sockets, its features may
+become more interesting on future high-speed fabrics/interconnects.
+
+Ramster requires both kernel and userland support. The userland support,
+called ramster-tools, is known to work with EL6-based distros, but is a
+set of poorly-hacked slightly-modified cluster tools based on ocfs2, which
+includes an init file, a config file, and a userland binary that interfaces
+to the kernel. This state of userland support reflects the abysmal userland
+skills of this suitably-embarrassed author; any help/patches to turn
+ramster-tools into more distributable rpms/debs useful for a wider range
+of distros would be appreciated. The source RPM that can be used as a
+starting point is available at:
+ http://oss.oracle.com/projects/tmem/files/RAMster/
+
+As a result of this author's ignorance, userland setup described in this
+HOWTO assumes an EL6 distro and is described in EL6 syntax. Apologies
+if this offends anyone!
+
+Kernel support has only been tested on x86_64. Systems with an active
+ocfs2 filesystem should work, but since ramster leverages a lot of
+code from ocfs2, there may be latent issues. A kernel configuration that
+includes CONFIG_OCFS2_FS should build OK, and should certainly run OK
+if no ocfs2 filesystem is mounted.
+
+This HOWTO demonstrates memory capacity load balancing for a two-node
+cluster, where one node called the "local" node becomes overcommitted
+and the other node called the "remote" node provides additional RAM
+capacity for use by the local node. Ramster is capable of more complex
+topologies; see the last section titled "ADVANCED RAMSTER TOPOLOGIES".
+
+If you find any terms in this HOWTO unfamiliar or don't understand the
+motivation for ramster, the following LWN reading is recommended:
+-- Transcendent Memory in a Nutshell (lwn.net/Articles/454795)
+-- The future calculus of memory management (lwn.net/Articles/475681)
+And since ramster is built on top of zcache, this article may be helpful:
+-- In-kernel memory compression (lwn.net/Articles/545244)
+
+Now that you've memorized the contents of those articles, let's get started!
+
+A. PRELIMINARY
+
+1) Install two x86_64 Linux systems that are known to work when
+ upgraded to a recent upstream Linux kernel version.
+
+On each system:
+
+2) Configure, build and install, then boot Linux, just to ensure it
+ can be done with an unmodified upstream kernel. Confirm you booted
+ the upstream kernel with "uname -a".
+
+3) If you plan to do any performance testing or unless you plan to
+ test only swapping, the "WasActive" patch is also highly recommended.
+ (Search lkml.org for WasActive, apply the patch, rebuild your kernel.)
+ For a demo or simple testing, the patch can be ignored.
+
+4) Install ramster-tools as root. An x86_64 rpm for EL6-based systems
+ can be found at:
+ http://oss.oracle.com/projects/tmem/files/RAMster/
+ (Sorry but for now, non-EL6 users must recreate ramster-tools on
+ their own from source. See above.)
+
+5) Ensure that debugfs is mounted at each boot. Examples below assume it
+ is mounted at /sys/kernel/debug.
+
+B. BUILDING RAMSTER INTO THE KERNEL
+
+Do the following on each system:
+
+1) Using the kernel configuration mechanism of your choice, change
+ your config to include:
+
+ CONFIG_CLEANCACHE=y
+ CONFIG_FRONTSWAP=y
+ CONFIG_STAGING=y
+ CONFIG_CONFIGFS_FS=y # NOTE: MUST BE y, not m
+ CONFIG_ZCACHE=y
+ CONFIG_RAMSTER=y
+
+ For a linux-3.10 or later kernel, you should also set:
+
+ CONFIG_ZCACHE_DEBUG=y
+ CONFIG_RAMSTER_DEBUG=y
+
+ Before building the kernel please doublecheck your kernel config
+ file to ensure all of the settings are correct.
+
+2) Build this kernel and change your boot file (e.g. /etc/grub.conf)
+ so that the new kernel will boot.
+
+3) Add "zcache" and "ramster" as kernel boot parameters for the new kernel.
+
+4) Reboot each system approximately simultaneously.
+
+5) Check dmesg to ensure there are some messages from ramster, prefixed
+ by "ramster:"
+
+ # dmesg | grep ramster
+
+ You should also see a lot of files in:
+
+ # ls /sys/kernel/debug/zcache
+ # ls /sys/kernel/debug/ramster
+
+ These are mostly counters for various zcache and ramster activities.
+ You should also see files in:
+
+ # ls /sys/kernel/mm/ramster
+
+ These are sysfs files that control ramster as we shall see.
+
+ Ramster now will act as a single-system zcache on each system
+ but doesn't yet know anything about the cluster so can't yet do
+ anything remotely.
+
+C. CONFIGURING THE RAMSTER CLUSTER
+
+This part can be error prone unless you are familiar with clustering
+filesystems. We need to describe the cluster in a /etc/ramster.conf
+file and the init scripts that parse it are extremely picky about
+the syntax.
+
+1) Create a /etc/ramster.conf file and ensure it is identical on both
+ systems. This file mimics the ocfs2 format and there is a good amount
+ of documentation that can be searched for ocfs2.conf, but you can use:
+
+ cluster:
+ name = ramster
+ node_count = 2
+ node:
+ name = system1
+ cluster = ramster
+ number = 0
+ ip_address = my.ip.ad.r1
+ ip_port = 7777
+ node:
+ name = system2
+ cluster = ramster
+ number = 1
+ ip_address = my.ip.ad.r2
+ ip_port = 7777
+
+ You must ensure that the "name" field in the file exactly matches
+ the output of "hostname" on each system; if "hostname" shows a
+ fully-qualified hostname, ensure the name is fully qualified in
+ /etc/ramster.conf. Obviously, substitute my.ip.ad.rx with proper
+ ip addresses.
+
+2) Enable the ramster service and configure it. If you used the
+ EL6 ramster-tools, this would be:
+
+ # chkconfig --add ramster
+ # service ramster configure
+
+ Set "load on boot" to "y", cluster to start is "ramster" (or whatever
+ name you chose in ramster.conf), heartbeat dead threshold as "500",
+ network idle timeout as "1000000". Leave the others as default.
+
+3) Reboot both systems. After reboot, try (assuming EL6 ramster-tools):
+
+ # service ramster status
+
+ You should see "Checking RAMSTER cluster "ramster": Online". If you do
+ not, something is wrong and ramster will not work. Note that you
+ should also see that the driver for "configfs" is loaded and mounted,
+ the driver for ocfs2_dlmfs is not loaded, and some numbers for network
+ parameters. You will also see "Checking RAMSTER heartbeat: Not active".
+ That's all OK.
+
+4) Now you need to start the cluster heartbeat; the cluster is not "up"
+ until all nodes detect a heartbeat. In a real cluster, heartbeat detection
+ is done via a cluster filesystem, but ramster doesn't require one. Some
+ hack-y kernel code in ramster can start the heartbeat for you though if
+ you tell it what nodes are "up". To enable the heartbeat, do:
+
+ # echo 0 > /sys/kernel/mm/ramster/manual_node_up
+ # echo 1 > /sys/kernel/mm/ramster/manual_node_up
+
+ This must be done on BOTH nodes and, to avoid timeouts, must be done
+ approximately concurrently on both nodes. On an EL6 system, it is
+ convenient to put these lines in /etc/rc.local. To confirm that the
+ cluster is now up, on both systems do:
+
+ # dmesg | grep ramster
+
+ You should see ramster "Accepted connection" messages in dmesg on both
+ nodes after this. Note that if you check userland status again with
+
+ # service ramster status
+
+ you will still see "Checking RAMSTER heartbeat: Not active". That's
+ still OK... the ramster kernel heartbeat hack doesn't communicate to
+ userland.
+
+5) You now must tell each node the node to which it should "remotify" pages.
+ On this two node cluster, we will assume the "local" node, node 0, has
+ memory overcommitted and will use ramster to utilize RAM capacity on
+ the "remote node", node 1. To configure this, on node 0, you do:
+
+ # echo 1 > /sys/kernel/mm/ramster/remote_target_nodenum
+
+ You should see "ramster: node 1 set as remotification target" in dmesg
+ on node 0. Again, on EL6, /etc/rc.local is a good place to put this
+ on node 0 so you don't forget to do it at each boot.
+
+6) One more step: By default, the ramster code does not "remotify" any
+ pages; this is primarily for testing purposes, but sometimes it is
+ useful. This may change in the future, but for now, on node 0, you do:
+
+ # echo 1 > /sys/kernel/mm/ramster/pers_remotify_enable
+ # echo 1 > /sys/kernel/mm/ramster/eph_remotify_enable
+
+ The first enables remotifying swap (persistent, aka frontswap) pages,
+ the second enables remotifying of page cache (ephemeral, cleancache)
+ pages.
+
+ On EL6, these lines can also be put in /etc/rc.local (AFTER the
+ node_up lines), or at the beginning of a script that runs a workload.
+
+7) Note that most testing has been done with both/all machines booted
+ roughly simultaneously to avoid cluster timeouts. Ideally, you should
+ do this too unless you are trying to break ramster rather than just
+ use it. ;-)
+
+D. TESTING RAMSTER
+
+1) Note that ramster has no value unless pages get "remotified". For
+ swap/frontswap/persistent pages, this doesn't happen unless/until
+ the workload would cause swapping to occur, at which point pages
+ are put into frontswap/zcache, and the remotification thread starts
+ working. To get to the point where the system swaps, you either
+ need a workload for which the working set exceeds the RAM in the
+ system; or you need to somehow reduce the amount of RAM one of
+ the system sees. This latter is easy when testing in a VM, but
+ harder on physical systems. In some cases, "mem=xxxM" on the
+ kernel command line restricts memory, but for some values of xxx
+ the kernel may fail to boot. One may also try creating a fixed
+ RAMdisk, doing nothing with it, but ensuring that it eats up a fixed
+ amount of RAM.
+
+2) To see if ramster is working, on the "remote node", node 1, try:
+
+ # grep . /sys/kernel/debug/ramster/foreign_*
+ # # note, that is space-dot-space between grep and the pathname
+
+ to monitor the number (and max) ephemeral and persistent pages
+ that ramster has sent. If these stay at zero, ramster is not working
+ either because the workload on the local node (node 0) isn't creating
+ enough memory pressure or because "remotifying" isn't working. On the
+ local system, node 0, you can watch lots of useful information also.
+ Try:
+
+ grep . /sys/kernel/debug/zcache/*pageframes* \
+ /sys/kernel/debug/zcache/*zbytes* \
+ /sys/kernel/debug/zcache/*zpages* \
+ /sys/kernel/debug/ramster/*remote*
+
+ Of particular note are the remote_*_pages_succ_get counters. These
+ show how many disk reads and/or disk writes have been avoided on the
+ overcommitted local system by storing pages remotely using ramster.
+
+ At the risk of information overload, you can also grep:
+
+ /sys/kernel/debug/cleancache/* and /sys/kernel/debug/frontswap/*
+
+ These show, for example, how many disk reads and/or disk writes have
+ been avoided by using zcache to optimize RAM on the local system.
+
+
+AUTOMATIC SWAP REPATRIATION
+
+You may notice that while the systems are idle, the foreign persistent
+page count on the remote machine slowly decreases. This is because
+ramster implements "frontswap selfshrinking": When possible, swap
+pages that have been remotified are slowly repatriated to the local
+machine. This is so that local RAM can be used when possible and
+so that, in case of remote machine crash, the probability of loss
+of data is reduced.
+
+REBOOTING / POWEROFF
+
+If a system is shut down while some of its swap pages still reside
+on a remote system, the system may lock up during the shutdown
+sequence. This will occur if the network is shut down before the
+swap mechansim is shut down, which is the default ordering on many
+distros. To avoid this annoying problem, simply shut off the swap
+subsystem before starting the shutdown sequence, e.g.:
+
+ # swapoff -a
+ # reboot
+
+Ideally, this swapoff-before-ifdown ordering should be enforced permanently
+using shutdown scripts.
+
+KNOWN PROBLEMS
+
+1) You may periodically see messages such as:
+
+ ramster_r2net, message length problem
+
+ This is harmless but indicates that a node is sending messages
+ containing compressed pages that exceed the maximum for zcache
+ (PAGE_SIZE*15/16). The sender side needs to be fixed.
+
+2) If you see a "No longer connected to node..." message or a "No connection
+ established with node X after N seconds", it is possible you may
+ be in an unrecoverable state. If you are certain all of the
+ appropriate cluster configuration steps described above have been
+ performed, try rebooting the two servers concurrently to see if
+ the cluster starts.
+
+ Note that "Connection to node... shutdown, state 7" is an intermediate
+ connection state. As long as you later see "Accepted connection", the
+ intermediate states are harmless.
+
+3) There are known issues in counting certain values. As a result
+ you may see periodic warnings from the kernel. Almost always you
+ will see "ramster: bad accounting for XXX". There are also "WARN_ONCE"
+ messages. If you see kernel warnings with a tombstone, please report
+ them. They are harmless but reflect bugs that need to be eventually fixed.
+
+ADVANCED RAMSTER TOPOLOGIES
+
+The kernel code for ramster can support up to eight nodes in a cluster,
+but no testing has been done with more than three nodes.
+
+In the example described above, the "remote" node serves as a RAM
+overflow for the "local" node. This can be made symmetric by appropriate
+settings of the sysfs remote_target_nodenum file. For example, by setting:
+
+ # echo 1 > /sys/kernel/mm/ramster/remote_target_nodenum
+
+on node 0, and
+
+ # echo 0 > /sys/kernel/mm/ramster/remote_target_nodenum
+
+on node 1, each node can serve as a RAM overflow for the other.
+
+For more than two nodes, a "RAM server" can be configured. For a
+three node system, set:
+
+ # echo 0 > /sys/kernel/mm/ramster/remote_target_nodenum
+
+on node 1, and
+
+ # echo 0 > /sys/kernel/mm/ramster/remote_target_nodenum
+
+on node 2. Then node 0 is a RAM server for node 1 and node 2.
+
+In this implementation of ramster, any remote node is potentially a single
+point of failure (SPOF). Though the probability of failure is reduced
+by automatic swap repatriation (see above), a proposed future enhancement
+to ramster improves high-availability for the cluster by sending a copy
+of each page of date to two other nodes. Patches welcome!
/* Used by this code. */
long ramster_flnodes;
-ssize_t ramster_foreign_eph_pages;
-ssize_t ramster_foreign_pers_pages;
/* FIXME frontswap selfshrinking knobs in debugfs? */
static LIST_HEAD(ramster_rem_op_list);
inc_ramster_foreign_eph_pages();
} else {
dec_ramster_foreign_eph_pages();
+#ifdef CONFIG_RAMSTER_DEBUG
WARN_ON_ONCE(ramster_foreign_eph_pages < 0);
+#endif
}
} else {
if (count > 0) {
inc_ramster_foreign_pers_pages();
} else {
dec_ramster_foreign_pers_pages();
+#ifdef CONFIG_RAMSTER_DEBUG
WARN_ON_ONCE(ramster_foreign_pers_pages < 0);
+#endif
}
}
}
#ifdef CONFIG_ZCACHE_MODULE
#ifdef CONFIG_RAMSTER
-module_param(ramster_enabled, int, S_IRUGO);
+module_param(ramster_enabled, bool, S_IRUGO);
module_param(disable_frontswap_selfshrink, int, S_IRUGO);
#endif
-module_param(disable_cleancache, int, S_IRUGO);
-module_param(disable_frontswap, int, S_IRUGO);
+module_param(disable_cleancache, bool, S_IRUGO);
+module_param(disable_frontswap, bool, S_IRUGO);
#ifdef FRONTSWAP_HAS_EXCLUSIVE_GETS
module_param(frontswap_has_exclusive_gets, bool, S_IRUGO);
#endif
-module_param(disable_frontswap_ignore_nonactive, int, S_IRUGO);
+module_param(disable_frontswap_ignore_nonactive, bool, S_IRUGO);
module_param(zcache_comp_name, charp, S_IRUGO);
module_init(zcache_init);
MODULE_LICENSE("GPL");
cmd->buf_ptr = kmemdup(buf, ISCSI_HDR_LEN, GFP_KERNEL);
if (!cmd->buf_ptr) {
pr_err("Unable to allocate memory for cmd->buf_ptr\n");
- iscsit_release_cmd(cmd);
+ iscsit_free_cmd(cmd, false);
return -1;
}
cmd->buf_ptr = kmemdup(buf, ISCSI_HDR_LEN, GFP_KERNEL);
if (!cmd->buf_ptr) {
pr_err("Unable to allocate memory for cmd->buf_ptr\n");
- iscsit_release_cmd(cmd);
+ iscsit_free_cmd(cmd, false);
return -1;
}
return 0;
out:
if (cmd)
- iscsit_release_cmd(cmd);
+ iscsit_free_cmd(cmd, false);
ping_out:
kfree(ping_data);
return ret;
if (conn->conn_state != TARG_CONN_STATE_LOGGED_IN) {
pr_err("Received logout request on connection that"
" is not in logged in state, ignoring request.\n");
- iscsit_release_cmd(cmd);
+ iscsit_free_cmd(cmd, false);
return 0;
}
list_del(&cmd->i_conn_node);
spin_unlock_bh(&conn->cmd_lock);
- iscsit_free_cmd(cmd);
+ iscsit_free_cmd(cmd, false);
break;
case ISTATE_SEND_NOPIN_WANT_RESPONSE:
iscsit_mod_nopin_response_timer(conn);
iscsit_increment_maxcmdsn(cmd, sess);
- iscsit_free_cmd(cmd);
+ iscsit_free_cmd(cmd, true);
spin_lock_bh(&conn->cmd_lock);
}
list_del(&cmd->i_conn_node);
cmd->conn = NULL;
spin_unlock(&cr->conn_recovery_cmd_lock);
- iscsit_free_cmd(cmd);
+ iscsit_free_cmd(cmd, true);
spin_lock(&cr->conn_recovery_cmd_lock);
}
spin_unlock(&cr->conn_recovery_cmd_lock);
list_del(&cmd->i_conn_node);
cmd->conn = NULL;
spin_unlock(&cr->conn_recovery_cmd_lock);
- iscsit_free_cmd(cmd);
+ iscsit_free_cmd(cmd, true);
spin_lock(&cr->conn_recovery_cmd_lock);
}
spin_unlock(&cr->conn_recovery_cmd_lock);
iscsit_remove_cmd_from_connection_recovery(cmd, sess);
spin_unlock(&cr->conn_recovery_cmd_lock);
- iscsit_free_cmd(cmd);
+ iscsit_free_cmd(cmd, true);
spin_lock(&cr->conn_recovery_cmd_lock);
}
spin_unlock(&cr->conn_recovery_cmd_lock);
list_del(&cmd->i_conn_node);
spin_unlock_bh(&conn->cmd_lock);
- iscsit_free_cmd(cmd);
+ iscsit_free_cmd(cmd, true);
spin_lock_bh(&conn->cmd_lock);
}
spin_unlock_bh(&conn->cmd_lock);
list_del(&cmd->i_conn_node);
spin_unlock_bh(&conn->cmd_lock);
- iscsit_free_cmd(cmd);
+ iscsit_free_cmd(cmd, true);
spin_lock_bh(&conn->cmd_lock);
continue;
}
iscsi_sna_gte(cmd->cmd_sn, conn->sess->exp_cmd_sn)) {
list_del(&cmd->i_conn_node);
spin_unlock_bh(&conn->cmd_lock);
- iscsit_free_cmd(cmd);
+ iscsit_free_cmd(cmd, true);
spin_lock_bh(&conn->cmd_lock);
continue;
}
}
INIT_LIST_HEAD(&extra_response->er_list);
- strncpy(extra_response->key, key, strlen(key) + 1);
- strncpy(extra_response->value, NOTUNDERSTOOD,
- strlen(NOTUNDERSTOOD) + 1);
+ strlcpy(extra_response->key, key, sizeof(extra_response->key));
+ strlcpy(extra_response->value, NOTUNDERSTOOD,
+ sizeof(extra_response->value));
list_add_tail(&extra_response->er_list,
¶m_list->extra_response_list);
if (phase & PHASE_SECURITY) {
if (iscsi_check_for_auth_key(key) > 0) {
- char *tmpptr = key + strlen(key);
- *tmpptr = '=';
kfree(tmpbuf);
return 1;
}
#ifndef ISCSI_PARAMETERS_H
#define ISCSI_PARAMETERS_H
+#include <scsi/iscsi_proto.h>
+
struct iscsi_extra_response {
- char key[64];
+ char key[KEY_MAXLEN];
char value[32];
struct list_head er_list;
} ____cacheline_aligned;
void iscsit_release_cmd(struct iscsi_cmd *cmd)
{
- struct iscsi_conn *conn = cmd->conn;
-
- iscsit_free_r2ts_from_list(cmd);
- iscsit_free_all_datain_reqs(cmd);
-
kfree(cmd->buf_ptr);
kfree(cmd->pdu_list);
kfree(cmd->seq_list);
kfree(cmd->tmr_req);
kfree(cmd->iov_data);
- if (conn) {
+ kmem_cache_free(lio_cmd_cache, cmd);
+}
+
+static void __iscsit_free_cmd(struct iscsi_cmd *cmd, bool scsi_cmd,
+ bool check_queues)
+{
+ struct iscsi_conn *conn = cmd->conn;
+
+ if (scsi_cmd) {
+ if (cmd->data_direction == DMA_TO_DEVICE) {
+ iscsit_stop_dataout_timer(cmd);
+ iscsit_free_r2ts_from_list(cmd);
+ }
+ if (cmd->data_direction == DMA_FROM_DEVICE)
+ iscsit_free_all_datain_reqs(cmd);
+ }
+
+ if (conn && check_queues) {
iscsit_remove_cmd_from_immediate_queue(cmd, conn);
iscsit_remove_cmd_from_response_queue(cmd, conn);
}
-
- kmem_cache_free(lio_cmd_cache, cmd);
}
-void iscsit_free_cmd(struct iscsi_cmd *cmd)
+void iscsit_free_cmd(struct iscsi_cmd *cmd, bool shutdown)
{
+ struct se_cmd *se_cmd = NULL;
+ int rc;
/*
* Determine if a struct se_cmd is associated with
* this struct iscsi_cmd.
*/
switch (cmd->iscsi_opcode) {
case ISCSI_OP_SCSI_CMD:
- if (cmd->data_direction == DMA_TO_DEVICE)
- iscsit_stop_dataout_timer(cmd);
+ se_cmd = &cmd->se_cmd;
+ __iscsit_free_cmd(cmd, true, shutdown);
/*
* Fallthrough
*/
case ISCSI_OP_SCSI_TMFUNC:
- transport_generic_free_cmd(&cmd->se_cmd, 1);
+ rc = transport_generic_free_cmd(&cmd->se_cmd, 1);
+ if (!rc && shutdown && se_cmd && se_cmd->se_sess) {
+ __iscsit_free_cmd(cmd, true, shutdown);
+ target_put_sess_cmd(se_cmd->se_sess, se_cmd);
+ }
break;
case ISCSI_OP_REJECT:
/*
* associated cmd->se_cmd needs to be released.
*/
if (cmd->se_cmd.se_tfo != NULL) {
- transport_generic_free_cmd(&cmd->se_cmd, 1);
+ se_cmd = &cmd->se_cmd;
+ __iscsit_free_cmd(cmd, true, shutdown);
+
+ rc = transport_generic_free_cmd(&cmd->se_cmd, 1);
+ if (!rc && shutdown && se_cmd->se_sess) {
+ __iscsit_free_cmd(cmd, true, shutdown);
+ target_put_sess_cmd(se_cmd->se_sess, se_cmd);
+ }
break;
}
/* Fall-through */
default:
+ __iscsit_free_cmd(cmd, false, shutdown);
cmd->release_cmd(cmd);
break;
}
extern bool iscsit_conn_all_queues_empty(struct iscsi_conn *);
extern void iscsit_free_queue_reqs_for_conn(struct iscsi_conn *);
extern void iscsit_release_cmd(struct iscsi_cmd *);
-extern void iscsit_free_cmd(struct iscsi_cmd *);
+extern void iscsit_free_cmd(struct iscsi_cmd *, bool);
extern int iscsit_check_session_usage_count(struct iscsi_session *);
extern void iscsit_dec_session_usage_count(struct iscsi_session *);
extern void iscsit_inc_session_usage_count(struct iscsi_session *);
struct request_queue *q = bdev_get_queue(inode->i_bdev);
unsigned long long dev_size;
+ fd_dev->fd_block_size = bdev_logical_block_size(inode->i_bdev);
/*
* Determine the number of bytes from i_size_read() minus
* one (1) logical sector from underlying struct block_device
goto fail;
}
+ fd_dev->fd_block_size = FD_BLOCKSIZE;
/*
* Limit UNMAP emulation to 8k Number of LBAs (NoLB)
*/
dev->dev_attrib.max_write_same_len = 0x1000;
}
- fd_dev->fd_block_size = dev->dev_attrib.hw_block_size;
-
- dev->dev_attrib.hw_block_size = FD_BLOCKSIZE;
+ dev->dev_attrib.hw_block_size = fd_dev->fd_block_size;
dev->dev_attrib.hw_max_sectors = FD_MAX_SECTORS;
dev->dev_attrib.hw_queue_depth = FD_MAX_DEVICE_QUEUE_DEPTH;
* to handle underlying block_device resize operations.
*/
if (S_ISBLK(i->i_mode))
- dev_size = (i_size_read(i) - fd_dev->fd_block_size);
+ dev_size = i_size_read(i);
else
dev_size = fd_dev->fd_dev_size;
- return div_u64(dev_size, dev->dev_attrib.block_size);
+ return div_u64(dev_size - dev->dev_attrib.block_size,
+ dev->dev_attrib.block_size);
}
static struct sbc_ops fd_sbc_ops = {
static void transport_handle_queue_full(struct se_cmd *cmd,
struct se_device *dev);
static int transport_generic_get_mem(struct se_cmd *cmd);
-static void transport_put_cmd(struct se_cmd *cmd);
+static int transport_put_cmd(struct se_cmd *cmd);
static void target_complete_ok_work(struct work_struct *work);
int init_se_kmem_caches(void)
INIT_LIST_HEAD(&se_sess->sess_list);
INIT_LIST_HEAD(&se_sess->sess_acl_list);
INIT_LIST_HEAD(&se_sess->sess_cmd_list);
+ INIT_LIST_HEAD(&se_sess->sess_wait_list);
spin_lock_init(&se_sess->sess_cmd_lock);
kref_init(&se_sess->sess_kref);
* This routine unconditionally frees a command, and reference counting
* or list removal must be done in the caller.
*/
-static void transport_release_cmd(struct se_cmd *cmd)
+static int transport_release_cmd(struct se_cmd *cmd)
{
BUG_ON(!cmd->se_tfo);
* If this cmd has been setup with target_get_sess_cmd(), drop
* the kref and call ->release_cmd() in kref callback.
*/
- if (cmd->check_release != 0) {
- target_put_sess_cmd(cmd->se_sess, cmd);
- return;
- }
+ if (cmd->check_release != 0)
+ return target_put_sess_cmd(cmd->se_sess, cmd);
+
cmd->se_tfo->release_cmd(cmd);
+ return 1;
}
/**
*
* This routine releases our reference to the command and frees it if possible.
*/
-static void transport_put_cmd(struct se_cmd *cmd)
+static int transport_put_cmd(struct se_cmd *cmd)
{
unsigned long flags;
if (atomic_read(&cmd->t_fe_count) &&
!atomic_dec_and_test(&cmd->t_fe_count)) {
spin_unlock_irqrestore(&cmd->t_state_lock, flags);
- return;
+ return 0;
}
if (cmd->transport_state & CMD_T_DEV_ACTIVE) {
spin_unlock_irqrestore(&cmd->t_state_lock, flags);
transport_free_pages(cmd);
- transport_release_cmd(cmd);
- return;
+ return transport_release_cmd(cmd);
}
void *transport_kmap_data_sg(struct se_cmd *cmd)
}
}
-void transport_generic_free_cmd(struct se_cmd *cmd, int wait_for_tasks)
+int transport_generic_free_cmd(struct se_cmd *cmd, int wait_for_tasks)
{
+ int ret = 0;
+
if (!(cmd->se_cmd_flags & SCF_SE_LUN_CMD)) {
if (wait_for_tasks && (cmd->se_cmd_flags & SCF_SCSI_TMR_CDB))
transport_wait_for_tasks(cmd);
- transport_release_cmd(cmd);
+ ret = transport_release_cmd(cmd);
} else {
if (wait_for_tasks)
transport_wait_for_tasks(cmd);
if (cmd->se_lun)
transport_lun_remove_cmd(cmd);
- transport_put_cmd(cmd);
+ ret = transport_put_cmd(cmd);
}
+ return ret;
}
EXPORT_SYMBOL(transport_generic_free_cmd);
unsigned long flags;
spin_lock_irqsave(&se_sess->sess_cmd_lock, flags);
-
- WARN_ON(se_sess->sess_tearing_down);
+ if (se_sess->sess_tearing_down) {
+ spin_unlock_irqrestore(&se_sess->sess_cmd_lock, flags);
+ return;
+ }
se_sess->sess_tearing_down = 1;
+ list_splice_init(&se_sess->sess_cmd_list, &se_sess->sess_wait_list);
- list_for_each_entry(se_cmd, &se_sess->sess_cmd_list, se_cmd_list)
+ list_for_each_entry(se_cmd, &se_sess->sess_wait_list, se_cmd_list)
se_cmd->cmd_wait_set = 1;
spin_unlock_irqrestore(&se_sess->sess_cmd_lock, flags);
/* target_wait_for_sess_cmds - Wait for outstanding descriptors
* @se_sess: session to wait for active I/O
- * @wait_for_tasks: Make extra transport_wait_for_tasks call
*/
-void target_wait_for_sess_cmds(
- struct se_session *se_sess,
- int wait_for_tasks)
+void target_wait_for_sess_cmds(struct se_session *se_sess)
{
struct se_cmd *se_cmd, *tmp_cmd;
- bool rc = false;
+ unsigned long flags;
list_for_each_entry_safe(se_cmd, tmp_cmd,
- &se_sess->sess_cmd_list, se_cmd_list) {
+ &se_sess->sess_wait_list, se_cmd_list) {
list_del(&se_cmd->se_cmd_list);
pr_debug("Waiting for se_cmd: %p t_state: %d, fabric state:"
" %d\n", se_cmd, se_cmd->t_state,
se_cmd->se_tfo->get_cmd_state(se_cmd));
- if (wait_for_tasks) {
- pr_debug("Calling transport_wait_for_tasks se_cmd: %p t_state: %d,"
- " fabric state: %d\n", se_cmd, se_cmd->t_state,
- se_cmd->se_tfo->get_cmd_state(se_cmd));
-
- rc = transport_wait_for_tasks(se_cmd);
-
- pr_debug("After transport_wait_for_tasks se_cmd: %p t_state: %d,"
- " fabric state: %d\n", se_cmd, se_cmd->t_state,
- se_cmd->se_tfo->get_cmd_state(se_cmd));
- }
-
- if (!rc) {
- wait_for_completion(&se_cmd->cmd_wait_comp);
- pr_debug("After cmd_wait_comp: se_cmd: %p t_state: %d"
- " fabric state: %d\n", se_cmd, se_cmd->t_state,
- se_cmd->se_tfo->get_cmd_state(se_cmd));
- }
+ wait_for_completion(&se_cmd->cmd_wait_comp);
+ pr_debug("After cmd_wait_comp: se_cmd: %p t_state: %d"
+ " fabric state: %d\n", se_cmd, se_cmd->t_state,
+ se_cmd->se_tfo->get_cmd_state(se_cmd));
se_cmd->se_tfo->release_cmd(se_cmd);
}
+
+ spin_lock_irqsave(&se_sess->sess_cmd_lock, flags);
+ WARN_ON(!list_empty(&se_sess->sess_cmd_list));
+ spin_unlock_irqrestore(&se_sess->sess_cmd_lock, flags);
+
}
EXPORT_SYMBOL(target_wait_for_sess_cmds);
*/
static void __exit ehv_bc_exit(void)
{
+ platform_driver_unregister(&ehv_bc_tty_driver);
tty_unregister_driver(ehv_bc_driver);
put_tty_driver(ehv_bc_driver);
kfree(bcs);
if (ip->type == PORT_16550A)
me->fifo[p] = 1;
- opmode = inb(ip->opmode_ioaddr)>>((p % 4) * 2);
- opmode &= OP_MODE_MASK;
+ if (ip->board->chip_flag == MOXA_MUST_MU860_HWID) {
+ opmode = inb(ip->opmode_ioaddr)>>((p % 4) * 2);
+ opmode &= OP_MODE_MASK;
+ } else {
+ opmode = RS232_MODE;
+ }
me->iftype[p] = opmode;
mutex_unlock(&port->mutex);
}
int shiftbit;
unsigned char val, mask;
+ if (info->board->chip_flag != MOXA_MUST_MU860_HWID)
+ return -EFAULT;
+
p = tty->index % 4;
if (cmd == MOXA_SET_OP_MODE) {
if (get_user(opmode, (int __user *) argp))
ldata->real_raw = 0;
}
n_tty_set_room(tty);
+ /*
+ * Fix tty hang when I_IXON(tty) is cleared, but the tty
+ * been stopped by STOP_CHAR(tty) before it.
+ */
+ if (!I_IXON(tty) && old && (old->c_iflag & IXON) && !tty->flow_stopped) {
+ start_tty(tty);
+ }
+
/* The termios change make the tty ready for I/O */
wake_up_interruptible(&tty->write_wait);
wake_up_interruptible(&tty->read_wait);
AIOP_INTR_BIT_3
};
+#ifdef CONFIG_PCI
static Word_t upci_aiop_intr_bits[AIOP_CTL_SIZE] = {
UPCI_AIOP_INTR_BIT_0,
UPCI_AIOP_INTR_BIT_1,
UPCI_AIOP_INTR_BIT_2,
UPCI_AIOP_INTR_BIT_3
};
+#endif
static Byte_t RData[RDATASIZE] = {
0x00, 0x09, 0xf6, 0x82,
static int __init init_ISA(int i);
static void rp_wait_until_sent(struct tty_struct *tty, int timeout);
static void rp_flush_buffer(struct tty_struct *tty);
-static void rmSpeakerReset(CONTROLLER_T * CtlP, unsigned long model);
static unsigned char GetLineNumber(int ctrl, int aiop, int ch);
static unsigned char SetLineNumber(int ctrl, int aiop, int ch);
static void rp_start(struct tty_struct *tty);
static void sModemReset(CONTROLLER_T * CtlP, int chan, int on);
static void sPCIModemReset(CONTROLLER_T * CtlP, int chan, int on);
static int sWriteTxPrioByte(CHANNEL_T * ChP, Byte_t Data);
-static int sPCIInitController(CONTROLLER_T * CtlP, int CtlNum,
- ByteIO_t * AiopIOList, int AiopIOListSize,
- WordIO_t ConfigIO, int IRQNum, Byte_t Frequency,
- int PeriodicOnly, int altChanRingIndicator,
- int UPCIRingInd);
static int sInitController(CONTROLLER_T * CtlP, int CtlNum, ByteIO_t MudbacIO,
ByteIO_t * AiopIOList, int AiopIOListSize,
int IRQNum, Byte_t Frequency, int PeriodicOnly);
};
MODULE_DEVICE_TABLE(pci, rocket_pci_ids);
+/* Resets the speaker controller on RocketModem II and III devices */
+static void rmSpeakerReset(CONTROLLER_T * CtlP, unsigned long model)
+{
+ ByteIO_t addr;
+
+ /* RocketModem II speaker control is at the 8th port location of offset 0x40 */
+ if ((model == MODEL_RP4M) || (model == MODEL_RP6M)) {
+ addr = CtlP->AiopIO[0] + 0x4F;
+ sOutB(addr, 0);
+ }
+
+ /* RocketModem III speaker control is at the 1st port location of offset 0x80 */
+ if ((model == MODEL_UPCI_RM3_8PORT)
+ || (model == MODEL_UPCI_RM3_4PORT)) {
+ addr = CtlP->AiopIO[0] + 0x88;
+ sOutB(addr, 0);
+ }
+}
+
+/***************************************************************************
+Function: sPCIInitController
+Purpose: Initialization of controller global registers and controller
+ structure.
+Call: sPCIInitController(CtlP,CtlNum,AiopIOList,AiopIOListSize,
+ IRQNum,Frequency,PeriodicOnly)
+ CONTROLLER_T *CtlP; Ptr to controller structure
+ int CtlNum; Controller number
+ ByteIO_t *AiopIOList; List of I/O addresses for each AIOP.
+ This list must be in the order the AIOPs will be found on the
+ controller. Once an AIOP in the list is not found, it is
+ assumed that there are no more AIOPs on the controller.
+ int AiopIOListSize; Number of addresses in AiopIOList
+ int IRQNum; Interrupt Request number. Can be any of the following:
+ 0: Disable global interrupts
+ 3: IRQ 3
+ 4: IRQ 4
+ 5: IRQ 5
+ 9: IRQ 9
+ 10: IRQ 10
+ 11: IRQ 11
+ 12: IRQ 12
+ 15: IRQ 15
+ Byte_t Frequency: A flag identifying the frequency
+ of the periodic interrupt, can be any one of the following:
+ FREQ_DIS - periodic interrupt disabled
+ FREQ_137HZ - 137 Hertz
+ FREQ_69HZ - 69 Hertz
+ FREQ_34HZ - 34 Hertz
+ FREQ_17HZ - 17 Hertz
+ FREQ_9HZ - 9 Hertz
+ FREQ_4HZ - 4 Hertz
+ If IRQNum is set to 0 the Frequency parameter is
+ overidden, it is forced to a value of FREQ_DIS.
+ int PeriodicOnly: 1 if all interrupts except the periodic
+ interrupt are to be blocked.
+ 0 is both the periodic interrupt and
+ other channel interrupts are allowed.
+ If IRQNum is set to 0 the PeriodicOnly parameter is
+ overidden, it is forced to a value of 0.
+Return: int: Number of AIOPs on the controller, or CTLID_NULL if controller
+ initialization failed.
+
+Comments:
+ If periodic interrupts are to be disabled but AIOP interrupts
+ are allowed, set Frequency to FREQ_DIS and PeriodicOnly to 0.
+
+ If interrupts are to be completely disabled set IRQNum to 0.
+
+ Setting Frequency to FREQ_DIS and PeriodicOnly to 1 is an
+ invalid combination.
+
+ This function performs initialization of global interrupt modes,
+ but it does not actually enable global interrupts. To enable
+ and disable global interrupts use functions sEnGlobalInt() and
+ sDisGlobalInt(). Enabling of global interrupts is normally not
+ done until all other initializations are complete.
+
+ Even if interrupts are globally enabled, they must also be
+ individually enabled for each channel that is to generate
+ interrupts.
+
+Warnings: No range checking on any of the parameters is done.
+
+ No context switches are allowed while executing this function.
+
+ After this function all AIOPs on the controller are disabled,
+ they can be enabled with sEnAiop().
+*/
+static int sPCIInitController(CONTROLLER_T * CtlP, int CtlNum,
+ ByteIO_t * AiopIOList, int AiopIOListSize,
+ WordIO_t ConfigIO, int IRQNum, Byte_t Frequency,
+ int PeriodicOnly, int altChanRingIndicator,
+ int UPCIRingInd)
+{
+ int i;
+ ByteIO_t io;
+
+ CtlP->AltChanRingIndicator = altChanRingIndicator;
+ CtlP->UPCIRingInd = UPCIRingInd;
+ CtlP->CtlNum = CtlNum;
+ CtlP->CtlID = CTLID_0001; /* controller release 1 */
+ CtlP->BusType = isPCI; /* controller release 1 */
+
+ if (ConfigIO) {
+ CtlP->isUPCI = 1;
+ CtlP->PCIIO = ConfigIO + _PCI_9030_INT_CTRL;
+ CtlP->PCIIO2 = ConfigIO + _PCI_9030_GPIO_CTRL;
+ CtlP->AiopIntrBits = upci_aiop_intr_bits;
+ } else {
+ CtlP->isUPCI = 0;
+ CtlP->PCIIO =
+ (WordIO_t) ((ByteIO_t) AiopIOList[0] + _PCI_INT_FUNC);
+ CtlP->AiopIntrBits = aiop_intr_bits;
+ }
+
+ sPCIControllerEOI(CtlP); /* clear EOI if warm init */
+ /* Init AIOPs */
+ CtlP->NumAiop = 0;
+ for (i = 0; i < AiopIOListSize; i++) {
+ io = AiopIOList[i];
+ CtlP->AiopIO[i] = (WordIO_t) io;
+ CtlP->AiopIntChanIO[i] = io + _INT_CHAN;
+
+ CtlP->AiopID[i] = sReadAiopID(io); /* read AIOP ID */
+ if (CtlP->AiopID[i] == AIOPID_NULL) /* if AIOP does not exist */
+ break; /* done looking for AIOPs */
+
+ CtlP->AiopNumChan[i] = sReadAiopNumChan((WordIO_t) io); /* num channels in AIOP */
+ sOutW((WordIO_t) io + _INDX_ADDR, _CLK_PRE); /* clock prescaler */
+ sOutB(io + _INDX_DATA, sClockPrescale);
+ CtlP->NumAiop++; /* bump count of AIOPs */
+ }
+
+ if (CtlP->NumAiop == 0)
+ return (-1);
+ else
+ return (CtlP->NumAiop);
+}
+
/*
* Called when a PCI card is found. Retrieves and stores model information,
* init's aiopic and serial port hardware.
return (CtlP->NumAiop);
}
-#ifdef CONFIG_PCI
-/***************************************************************************
-Function: sPCIInitController
-Purpose: Initialization of controller global registers and controller
- structure.
-Call: sPCIInitController(CtlP,CtlNum,AiopIOList,AiopIOListSize,
- IRQNum,Frequency,PeriodicOnly)
- CONTROLLER_T *CtlP; Ptr to controller structure
- int CtlNum; Controller number
- ByteIO_t *AiopIOList; List of I/O addresses for each AIOP.
- This list must be in the order the AIOPs will be found on the
- controller. Once an AIOP in the list is not found, it is
- assumed that there are no more AIOPs on the controller.
- int AiopIOListSize; Number of addresses in AiopIOList
- int IRQNum; Interrupt Request number. Can be any of the following:
- 0: Disable global interrupts
- 3: IRQ 3
- 4: IRQ 4
- 5: IRQ 5
- 9: IRQ 9
- 10: IRQ 10
- 11: IRQ 11
- 12: IRQ 12
- 15: IRQ 15
- Byte_t Frequency: A flag identifying the frequency
- of the periodic interrupt, can be any one of the following:
- FREQ_DIS - periodic interrupt disabled
- FREQ_137HZ - 137 Hertz
- FREQ_69HZ - 69 Hertz
- FREQ_34HZ - 34 Hertz
- FREQ_17HZ - 17 Hertz
- FREQ_9HZ - 9 Hertz
- FREQ_4HZ - 4 Hertz
- If IRQNum is set to 0 the Frequency parameter is
- overidden, it is forced to a value of FREQ_DIS.
- int PeriodicOnly: 1 if all interrupts except the periodic
- interrupt are to be blocked.
- 0 is both the periodic interrupt and
- other channel interrupts are allowed.
- If IRQNum is set to 0 the PeriodicOnly parameter is
- overidden, it is forced to a value of 0.
-Return: int: Number of AIOPs on the controller, or CTLID_NULL if controller
- initialization failed.
-
-Comments:
- If periodic interrupts are to be disabled but AIOP interrupts
- are allowed, set Frequency to FREQ_DIS and PeriodicOnly to 0.
-
- If interrupts are to be completely disabled set IRQNum to 0.
-
- Setting Frequency to FREQ_DIS and PeriodicOnly to 1 is an
- invalid combination.
-
- This function performs initialization of global interrupt modes,
- but it does not actually enable global interrupts. To enable
- and disable global interrupts use functions sEnGlobalInt() and
- sDisGlobalInt(). Enabling of global interrupts is normally not
- done until all other initializations are complete.
-
- Even if interrupts are globally enabled, they must also be
- individually enabled for each channel that is to generate
- interrupts.
-
-Warnings: No range checking on any of the parameters is done.
-
- No context switches are allowed while executing this function.
-
- After this function all AIOPs on the controller are disabled,
- they can be enabled with sEnAiop().
-*/
-static int sPCIInitController(CONTROLLER_T * CtlP, int CtlNum,
- ByteIO_t * AiopIOList, int AiopIOListSize,
- WordIO_t ConfigIO, int IRQNum, Byte_t Frequency,
- int PeriodicOnly, int altChanRingIndicator,
- int UPCIRingInd)
-{
- int i;
- ByteIO_t io;
-
- CtlP->AltChanRingIndicator = altChanRingIndicator;
- CtlP->UPCIRingInd = UPCIRingInd;
- CtlP->CtlNum = CtlNum;
- CtlP->CtlID = CTLID_0001; /* controller release 1 */
- CtlP->BusType = isPCI; /* controller release 1 */
-
- if (ConfigIO) {
- CtlP->isUPCI = 1;
- CtlP->PCIIO = ConfigIO + _PCI_9030_INT_CTRL;
- CtlP->PCIIO2 = ConfigIO + _PCI_9030_GPIO_CTRL;
- CtlP->AiopIntrBits = upci_aiop_intr_bits;
- } else {
- CtlP->isUPCI = 0;
- CtlP->PCIIO =
- (WordIO_t) ((ByteIO_t) AiopIOList[0] + _PCI_INT_FUNC);
- CtlP->AiopIntrBits = aiop_intr_bits;
- }
-
- sPCIControllerEOI(CtlP); /* clear EOI if warm init */
- /* Init AIOPs */
- CtlP->NumAiop = 0;
- for (i = 0; i < AiopIOListSize; i++) {
- io = AiopIOList[i];
- CtlP->AiopIO[i] = (WordIO_t) io;
- CtlP->AiopIntChanIO[i] = io + _INT_CHAN;
-
- CtlP->AiopID[i] = sReadAiopID(io); /* read AIOP ID */
- if (CtlP->AiopID[i] == AIOPID_NULL) /* if AIOP does not exist */
- break; /* done looking for AIOPs */
-
- CtlP->AiopNumChan[i] = sReadAiopNumChan((WordIO_t) io); /* num channels in AIOP */
- sOutW((WordIO_t) io + _INDX_ADDR, _CLK_PRE); /* clock prescaler */
- sOutB(io + _INDX_DATA, sClockPrescale);
- CtlP->NumAiop++; /* bump count of AIOPs */
- }
-
- if (CtlP->NumAiop == 0)
- return (-1);
- else
- return (CtlP->NumAiop);
-}
-
-/* Resets the speaker controller on RocketModem II and III devices */
-static void rmSpeakerReset(CONTROLLER_T * CtlP, unsigned long model)
-{
- ByteIO_t addr;
-
- /* RocketModem II speaker control is at the 8th port location of offset 0x40 */
- if ((model == MODEL_RP4M) || (model == MODEL_RP6M)) {
- addr = CtlP->AiopIO[0] + 0x4F;
- sOutB(addr, 0);
- }
-
- /* RocketModem III speaker control is at the 1st port location of offset 0x80 */
- if ((model == MODEL_UPCI_RM3_8PORT)
- || (model == MODEL_UPCI_RM3_4PORT)) {
- addr = CtlP->AiopIO[0] + 0x88;
- sOutB(addr, 0);
- }
-}
-#endif
-
/***************************************************************************
Function: sReadAiopID
Purpose: Read the AIOP idenfication number directly from an AIOP.
if (nr_uarts > UART_NR)
nr_uarts = UART_NR;
- for (i = 0; i < UART_NR; i++) {
+ for (i = 0; i < nr_uarts; i++) {
struct uart_8250_port *up = &serial8250_ports[i];
struct uart_port *port = &up->port;
* if so, search for the first available port that does have
* console support.
*/
- if (co->index >= UART_NR)
+ if (co->index >= nr_uarts)
co->index = 0;
port = &serial8250_ports[co->index].port;
if (!port->iobase && !port->membase)
int line;
struct uart_port *port;
- for (line = 0; line < UART_NR; line++) {
+ for (line = 0; line < nr_uarts; line++) {
port = &serial8250_ports[line].port;
if (uart_match_port(p, port))
return line;
{
int i;
- for (i = 0; i < UART_NR; i++) {
+ for (i = 0; i < nr_uarts; i++) {
struct uart_8250_port *up = &serial8250_ports[i];
if (up->port.dev == &dev->dev)
/*
* First, find a port entry which matches.
*/
- for (i = 0; i < UART_NR; i++)
+ for (i = 0; i < nr_uarts; i++)
if (uart_match_port(&serial8250_ports[i].port, port))
return &serial8250_ports[i];
* free entry. We look for one which hasn't been previously
* used (indicated by zero iobase).
*/
- for (i = 0; i < UART_NR; i++)
+ for (i = 0; i < nr_uarts; i++)
if (serial8250_ports[i].port.type == PORT_UNKNOWN &&
serial8250_ports[i].port.iobase == 0)
return &serial8250_ports[i];
* That also failed. Last resort is to find any entry which
* doesn't have a real port associated with it.
*/
- for (i = 0; i < UART_NR; i++)
+ for (i = 0; i < nr_uarts; i++)
if (serial8250_ports[i].port.type == PORT_UNKNOWN)
return &serial8250_ports[i];
{
struct dw8250_data *data = dev_get_drvdata(dev);
- clk_disable_unprepare(data->clk);
+ if (!IS_ERR(data->clk))
+ clk_disable_unprepare(data->clk);
return 0;
}
{
struct dw8250_data *data = dev_get_drvdata(dev);
- clk_prepare_enable(data->clk);
+ if (!IS_ERR(data->clk))
+ clk_prepare_enable(data->clk);
return 0;
}
static const struct acpi_device_id dw8250_acpi_match[] = {
{ "INT33C4", 0 },
{ "INT33C5", 0 },
+ { "80860F0A", 0 },
{ },
};
MODULE_DEVICE_TABLE(acpi, dw8250_acpi_match);
dmaengine_slave_config(chan, &rx_conf);
uap->dmarx.chan = chan;
- if (plat->dma_rx_poll_enable) {
+ if (plat && plat->dma_rx_poll_enable) {
/* Set poll rate if specified. */
if (plat->dma_rx_poll_rate) {
uap->dmarx.auto_poll_rate = false;
temp = readl(sport->port.membase + UCR2);
temp |= (UCR2_RXEN | UCR2_TXEN);
+ if (!sport->have_rtscts)
+ temp |= UCR2_IRTS;
writel(temp, sport->port.membase + UCR2);
if (USE_IRDA(sport)) {
if (rc)
return rc;
rc = platform_driver_register(&mcf_platform_driver);
- if (rc)
+ if (rc) {
+ uart_unregister_driver(&mcf_driver);
return rc;
+ }
return 0;
}
if (psc_ops && psc_ops->fifoc_init) {
ret = psc_ops->fifoc_init();
if (ret)
- return ret;
+ goto err_init;
}
ret = platform_driver_register(&mpc52xx_uart_of_driver);
if (ret) {
printk(KERN_ERR "%s: platform_driver_register failed (%i)\n",
__FILE__, ret);
- uart_unregister_driver(&mpc52xx_uart_driver);
- return ret;
+ goto err_reg;
}
return 0;
+err_reg:
+ if (psc_ops && psc_ops->fifoc_uninit)
+ psc_ops->fifoc_uninit();
+err_init:
+ uart_unregister_driver(&mpc52xx_uart_driver);
+ return ret;
}
static void __exit
dcr_write(up->dcr_host, UART_IER, up->ier);
/* free irq */
- free_irq(up->port.irq, port);
+ free_irq(up->port.irq, up);
}
static int nwpserial_verify_port(struct uart_port *port,
return pdata->get_context_loss_count(up->dev);
}
-static void serial_omap_set_forceidle(struct uart_omap_port *up)
-{
- struct omap_uart_port_info *pdata = up->dev->platform_data;
-
- if (!pdata || !pdata->set_forceidle)
- return;
-
- pdata->set_forceidle(up->dev);
-}
-
-static void serial_omap_set_noidle(struct uart_omap_port *up)
-{
- struct omap_uart_port_info *pdata = up->dev->platform_data;
-
- if (!pdata || !pdata->set_noidle)
- return;
-
- pdata->set_noidle(up->dev);
-}
-
static void serial_omap_enable_wakeup(struct uart_omap_port *up, bool enable)
{
struct omap_uart_port_info *pdata = up->dev->platform_data;
serial_out(up, UART_IER, up->ier);
}
- serial_omap_set_forceidle(up);
-
pm_runtime_mark_last_busy(up->dev);
pm_runtime_put_autosuspend(up->dev);
}
pm_runtime_get_sync(up->dev);
serial_omap_enable_ier_thri(up);
- serial_omap_set_noidle(up);
pm_runtime_mark_last_busy(up->dev);
pm_runtime_put_autosuspend(up->dev);
}
ourport->tx_irq = ret;
ourport->clk = clk_get(&platdev->dev, "uart");
+ if (IS_ERR(ourport->clk)) {
+ pr_err("%s: Controller clock not found\n",
+ dev_name(&platdev->dev));
+ return PTR_ERR(ourport->clk);
+ }
+
+ ret = clk_prepare_enable(ourport->clk);
+ if (ret) {
+ pr_err("uart: clock failed to prepare+enable: %d\n", ret);
+ clk_put(ourport->clk);
+ return ret;
+ }
/* Keep all interrupts masked and cleared */
if (s3c24xx_serial_has_interrupt_mask(port)) {
/* reset the fifos (and setup the uart) */
s3c24xx_serial_resetport(port, cfg);
+ clk_disable_unprepare(ourport->clk);
return 0;
}
static void __exit s3c24xx_serial_modexit(void)
{
+ platform_driver_unregister(&samsung_serial_driver);
uart_unregister_driver(&s3c24xx_uart_drv);
}
con_set_default_unimap(vc);
vc->vc_screenbuf = kmalloc(vc->vc_screenbuf_size, GFP_KERNEL);
if (!vc->vc_screenbuf) {
- tty_port_destroy(&vc->port);
kfree(vc);
vc_cons[currcons].d = NULL;
return -ENOMEM;
return ret;
}
-void vc_deallocate(unsigned int currcons)
+struct vc_data *vc_deallocate(unsigned int currcons)
{
+ struct vc_data *vc = NULL;
+
WARN_CONSOLE_UNLOCKED();
if (vc_cons_allocated(currcons)) {
- struct vc_data *vc = vc_cons[currcons].d;
- struct vt_notifier_param param = { .vc = vc };
+ struct vt_notifier_param param;
+ param.vc = vc = vc_cons[currcons].d;
atomic_notifier_call_chain(&vt_notifier_list, VT_DEALLOCATE, ¶m);
vcs_remove_sysfs(currcons);
vc->vc_sw->con_deinit(vc);
put_pid(vc->vt_pid);
module_put(vc->vc_sw->owner);
kfree(vc->vc_screenbuf);
- if (currcons >= MIN_NR_CONSOLES) {
- tty_port_destroy(&vc->port);
- kfree(vc);
- }
vc_cons[currcons].d = NULL;
}
+ return vc;
}
/*
return 0;
}
+/* deallocate a single console, if possible (leave 0) */
+static int vt_disallocate(unsigned int vc_num)
+{
+ struct vc_data *vc = NULL;
+ int ret = 0;
+
+ if (!vc_num)
+ return 0;
+
+ console_lock();
+ if (VT_BUSY(vc_num))
+ ret = -EBUSY;
+ else
+ vc = vc_deallocate(vc_num);
+ console_unlock();
+
+ if (vc && vc_num >= MIN_NR_CONSOLES) {
+ tty_port_destroy(&vc->port);
+ kfree(vc);
+ }
+
+ return ret;
+}
+
+/* deallocate all unused consoles, but leave 0 */
+static void vt_disallocate_all(void)
+{
+ struct vc_data *vc[MAX_NR_CONSOLES];
+ int i;
+
+ console_lock();
+ for (i = 1; i < MAX_NR_CONSOLES; i++)
+ if (!VT_BUSY(i))
+ vc[i] = vc_deallocate(i);
+ else
+ vc[i] = NULL;
+ console_unlock();
+
+ for (i = 1; i < MAX_NR_CONSOLES; i++) {
+ if (vc[i] && i >= MIN_NR_CONSOLES) {
+ tty_port_destroy(&vc[i]->port);
+ kfree(vc[i]);
+ }
+ }
+}
/*
ret = -ENXIO;
break;
}
- if (arg == 0) {
- /* deallocate all unused consoles, but leave 0 */
- console_lock();
- for (i=1; i<MAX_NR_CONSOLES; i++)
- if (! VT_BUSY(i))
- vc_deallocate(i);
- console_unlock();
- } else {
- /* deallocate a single console, if possible */
- arg--;
- if (VT_BUSY(arg))
- ret = -EBUSY;
- else if (arg) { /* leave 0 */
- console_lock();
- vc_deallocate(arg);
- console_unlock();
- }
- }
+ if (arg == 0)
+ vt_disallocate_all();
+ else
+ ret = vt_disallocate(--arg);
break;
case VT_RESIZE:
config UIO_DMEM_GENIRQ
tristate "Userspace platform driver with generic irq and dynamic memory"
+ depends on HAS_DMA
help
Platform driver for Userspace I/O devices, including generic
interrupt handling code. Shared interrupts are not supported.
{
int ret, len;
__le32 *buf;
- int offb, offd;
+ int offb;
+ unsigned int offd;
const int stride = CMD_PACKET_SIZE / (4 * 2) - 1;
int buflen = ((size - 1) / stride + 1 + size * 2) * 4;
config USB_CHIPIDEA_HOST
bool "ChipIdea host controller"
depends on USB=y || USB=USB_CHIPIDEA
- depends on USB_EHCI_HCD
+ depends on USB_EHCI_HCD=y
select USB_EHCI_ROOT_HUB_TT
help
Say Y here to enable host controller functionality of the
ci13xxx_imx_platdata.phy = data->phy;
- if (!pdev->dev.dma_mask) {
- pdev->dev.dma_mask = devm_kzalloc(&pdev->dev,
- sizeof(*pdev->dev.dma_mask), GFP_KERNEL);
- if (!pdev->dev.dma_mask) {
- ret = -ENOMEM;
- dev_err(&pdev->dev, "Failed to alloc dma_mask!\n");
- goto err;
- }
- *pdev->dev.dma_mask = DMA_BIT_MASK(32);
- dma_set_coherent_mask(&pdev->dev, *pdev->dev.dma_mask);
- }
+ if (!pdev->dev.dma_mask)
+ pdev->dev.dma_mask = &pdev->dev.coherent_dma_mask;
+ if (!pdev->dev.coherent_dma_mask)
+ pdev->dev.coherent_dma_mask = DMA_BIT_MASK(32);
if (usbmisc_ops && usbmisc_ops->init) {
ret = usbmisc_ops->init(&pdev->dev);
config USB_OTG
bool "OTG support"
- depends on USB_SUSPEND
+ depends on PM_RUNTIME
default n
help
The most notable feature of USB OTG is support for a
goto error;
}
for (totlen = u = 0; u < uurb->number_of_packets; u++) {
- /* arbitrary limit,
- * sufficient for USB 2.0 high-bandwidth iso */
- if (isopkt[u].length > 8192) {
+ /*
+ * arbitrary limit need for USB 3.0
+ * bMaxBurst (0~15 allowed, 1~16 packets)
+ * bmAttributes (bit 1:0, mult 0~2, 1~3 packets)
+ * sizemax: 1024 * 16 * 3 = 49152
+ */
+ if (isopkt[u].length > 49152) {
ret = -EINVAL;
goto error;
}
/* Edirol SD-20 */
{ USB_DEVICE(0x0582, 0x0027), .driver_info = USB_QUIRK_RESET_RESUME },
+ /* Alcor Micro Corp. Hub */
+ { USB_DEVICE(0x058f, 0x9254), .driver_info = USB_QUIRK_RESET_RESUME },
+
/* appletouch */
{ USB_DEVICE(0x05ac, 0x021a), .driver_info = USB_QUIRK_RESET_RESUME },
config USB_DWC3_HOST
bool "Host only mode"
- depends on USB
+ depends on USB=y || USB=USB_DWC3
help
Select this when you want to use DWC3 in host mode only,
thereby the gadget feature will be regressed.
config USB_DWC3_GADGET
bool "Gadget only mode"
- depends on USB_GADGET
+ depends on USB_GADGET=y || USB_GADGET=USB_DWC3
help
Select this when you want to use DWC3 in gadget mode only,
thereby the host feature will be regressed.
config USB_DWC3_DUAL_ROLE
bool "Dual Role mode"
- depends on (USB && USB_GADGET)
+ depends on ((USB=y || USB=USB_DWC3) && (USB_GADGET=y || USB_GADGET=USB_DWC3))
help
This is the default mode of working of DWC3 controller where
both host and gadget features are enabled.
return 0;
}
-static u64 dwc3_exynos_dma_mask = DMA_BIT_MASK(32);
-
static int dwc3_exynos_probe(struct platform_device *pdev)
{
struct dwc3_exynos *exynos;
* Once we move to full device tree support this will vanish off.
*/
if (!dev->dma_mask)
- dev->dma_mask = &dwc3_exynos_dma_mask;
+ dev->dma_mask = &dev->coherent_dma_mask;
+ if (!dev->coherent_dma_mask)
+ dev->coherent_dma_mask = DMA_BIT_MASK(32);
platform_set_drvdata(pdev, exynos);
{
struct dwc3_exynos *exynos = platform_get_drvdata(pdev);
+ device_for_each_child(&pdev->dev, NULL, dwc3_exynos_remove_child);
platform_device_unregister(exynos->usb2_phy);
platform_device_unregister(exynos->usb3_phy);
- device_for_each_child(&pdev->dev, NULL, dwc3_exynos_remove_child);
clk_disable_unprepare(exynos->clk);
{
struct dwc3_pci *glue = pci_get_drvdata(pci);
+ platform_device_unregister(glue->dwc3);
platform_device_unregister(glue->usb2_phy);
platform_device_unregister(glue->usb3_phy);
- platform_device_unregister(glue->dwc3);
pci_set_drvdata(pci, NULL);
pci_disable_device(pci);
}
dep = dwc->eps[epnum];
if (!dep)
continue;
-
- dwc3_free_trb_pool(dep);
-
- if (epnum != 0 && epnum != 1)
+ /*
+ * Physical endpoints 0 and 1 are special; they form the
+ * bi-directional USB endpoint 0.
+ *
+ * For those two physical endpoints, we don't allocate a TRB
+ * pool nor do we add them the endpoints list. Due to that, we
+ * shouldn't do these two operations otherwise we would end up
+ * with all sorts of bugs when removing dwc3.ko.
+ */
+ if (epnum != 0 && epnum != 1) {
+ dwc3_free_trb_pool(dep);
list_del(&dep->endpoint.ep_list);
+ }
kfree(dep);
}
depends on ARCH_LPC32XX
depends on USB_PHY
select USB_ISP1301
- select USB_OTG_UTILS
help
This option selects the USB device controller in the LPC32xx SoC.
err_get_hclk:
clk_put(pclk);
- platform_set_drvdata(pdev, NULL);
-
return ret;
}
usb_del_gadget_udc(&udc->gadget);
BUG_ON(udc->driver);
- platform_set_drvdata(pdev, NULL);
bcm63xx_uninit_udc_hw(udc);
return 0;
gi->gstrings[i] = NULL;
s = usb_gstrings_attach(&gi->cdev, gi->gstrings,
USB_GADGET_FIRST_AVAIL_IDX);
- if (IS_ERR(s))
+ if (IS_ERR(s)) {
+ ret = PTR_ERR(s);
goto err_comp_cleanup;
+ }
gi->cdev.desc.iManufacturer = s[USB_GADGET_MANUFACTURER_IDX].id;
gi->cdev.desc.iProduct = s[USB_GADGET_PRODUCT_IDX].id;
}
cfg->gstrings[i] = NULL;
s = usb_gstrings_attach(&gi->cdev, cfg->gstrings, 1);
- if (IS_ERR(s))
+ if (IS_ERR(s)) {
+ ret = PTR_ERR(s);
goto err_comp_cleanup;
+ }
c->iConfiguration = s[0].id;
}
struct dummy *dum = platform_get_drvdata(pdev);
usb_del_gadget_udc(&dum->gadget);
- platform_set_drvdata(pdev, NULL);
device_remove_file(&dum->gadget.dev, &dev_attr_function);
return 0;
}
}
for (i = 0; i < mod_data.num; i++) {
dum[i] = kzalloc(sizeof(struct dummy), GFP_KERNEL);
- if (!dum[i])
+ if (!dum[i]) {
+ retval = -ENOMEM;
goto err_add_pdata;
+ }
retval = platform_device_add_data(the_hcd_pdev[i], &dum[i],
sizeof(void *));
if (retval)
* @c: the configuration to support the network link
* @ethaddr: a buffer in which the ethernet address of the host side
* side of the link was recorded
+ * @dev: eth_dev structure
* Context: single threaded during gadget setup
*
* Returns zero on success, else negative errno.
* @c: the configuration to support the network link
* @ethaddr: a buffer in which the ethernet address of the host side
* side of the link was recorded
+ * @dev: eth_dev structure
* Context: single threaded during gadget setup
*
* Returns zero on success, else negative errno.
{
struct snd_card *card = platform_get_drvdata(pdev);
- platform_set_drvdata(pdev, NULL);
-
if (card)
return snd_card_free(card);
fusb300->ep0_req = fusb300_alloc_request(&fusb300->ep[0]->ep,
GFP_KERNEL);
- if (fusb300->ep0_req == NULL)
+ if (fusb300->ep0_req == NULL) {
+ ret = -ENOMEM;
goto clean_up3;
+ }
init_controller(fusb300);
ret = usb_add_gadget_udc(&pdev->dev, &fusb300->gadget);
if (pdata->exit)
pdata->exit(&pdev->dev);
- platform_set_drvdata(pdev, NULL);
-
return 0;
}
m66592->epaddr2ep[0] = &m66592->ep[0];
m66592->ep0_req = m66592_alloc_request(&m66592->ep[0].ep, GFP_KERNEL);
- if (m66592->ep0_req == NULL)
+ if (m66592->ep0_req == NULL) {
+ ret = -ENOMEM;
goto clean_up3;
+ }
m66592->ep0_req->complete = nop_completion;
init_controller(m66592);
dev->transceiver = NULL;
}
- platform_set_drvdata(pdev, NULL);
the_controller = NULL;
return 0;
}
r8a66597->ep0_req = r8a66597_alloc_request(&r8a66597->ep[0].ep,
GFP_KERNEL);
- if (r8a66597->ep0_req == NULL)
+ if (r8a66597->ep0_req == NULL) {
+ ret = -ENOMEM;
goto clean_up3;
+ }
r8a66597->ep0_req->complete = nop_completion;
ret = usb_add_gadget_udc(&pdev->dev, &r8a66597->gadget);
if (hs_req->req.length == 0)
return;
- usb_gadget_unmap_request(&hsotg->gadget, hs_req, hs_ep->dir_in);
+ usb_gadget_unmap_request(&hsotg->gadget, req, hs_ep->dir_in);
}
/**
irq = gpio_to_irq(udc_info->vbus_pin);
if (irq < 0) {
dev_err(dev, "no irq for gpio vbus pin\n");
+ retval = irq;
goto err_gpio_claim;
}
iounmap(base_addr);
release_mem_region(rsrc_start, rsrc_len);
- platform_set_drvdata(pdev, NULL);
-
if (!IS_ERR(udc_clock) && udc_clock != NULL) {
clk_disable(udc_clock);
clk_put(udc_clock);
ss_opts->bulk_buflen = gzero_options.bulk_buflen;
func_ss = usb_get_function(func_inst_ss);
- if (IS_ERR(func_ss))
+ if (IS_ERR(func_ss)) {
+ status = PTR_ERR(func_ss);
goto err_put_func_inst_ss;
+ }
func_inst_lb = usb_get_function_instance("Loopback");
- if (IS_ERR(func_inst_lb))
+ if (IS_ERR(func_inst_lb)) {
+ status = PTR_ERR(func_inst_lb);
goto err_put_func_ss;
+ }
lb_opts = container_of(func_inst_lb, struct f_lb_opts, func_inst);
lb_opts->bulk_buflen = gzero_options.bulk_buflen;
config USB_UHCI_HCD
tristate "UHCI HCD (most Intel and VIA) support"
- depends on PCI || SPARC_LEON || ARCH_VT8500
+ depends on PCI || USB_UHCI_SUPPORT_NON_PCI_HC
---help---
The Universal Host Controller Interface is a standard by Intel for
accessing the USB hardware in the PC (which is also called the USB
config USB_UHCI_SUPPORT_NON_PCI_HC
bool
- depends on USB_UHCI_HCD
- default y if (SPARC_LEON || ARCH_VT8500)
+ default y if (SPARC_LEON || USB_UHCI_PLATFORM)
config USB_UHCI_PLATFORM
- bool "Generic UHCI Platform Driver support"
- depends on USB_UHCI_SUPPORT_NON_PCI_HC
+ bool
default y if ARCH_VT8500
- ---help---
- Enable support for generic UHCI platform devices that require no
- additional configuration.
config USB_UHCI_BIG_ENDIAN_MMIO
bool
- depends on USB_UHCI_SUPPORT_NON_PCI_HC && SPARC_LEON
- default y
+ default y if SPARC_LEON
config USB_UHCI_BIG_ENDIAN_DESC
bool
- depends on USB_UHCI_SUPPORT_NON_PCI_HC && SPARC_LEON
- default y
+ default y if SPARC_LEON
config USB_FHCI_HCD
tristate "Freescale QE USB Host Controller support"
/*-------------------------------------------------------------------------*/
-static u64 at91_ehci_dma_mask = DMA_BIT_MASK(32);
-
static int ehci_atmel_drv_probe(struct platform_device *pdev)
{
struct usb_hcd *hcd;
* Once we have dma capability bindings this can go away.
*/
if (!pdev->dev.dma_mask)
- pdev->dev.dma_mask = &at91_ehci_dma_mask;
+ pdev->dev.dma_mask = &pdev->dev.coherent_dma_mask;
+ if (!pdev->dev.coherent_dma_mask)
+ pdev->dev.coherent_dma_mask = DMA_BIT_MASK(32);
hcd = usb_create_hcd(driver, &pdev->dev, dev_name(&pdev->dev));
if (!hcd) {
#define PLATFORM_DRIVER ehci_hcd_sead3_driver
#endif
-#if !IS_ENABLED(CONFIG_USB_EHCI_PCI) && \
- !IS_ENABLED(CONFIG_USB_EHCI_HCD_PLATFORM) && \
- !IS_ENABLED(CONFIG_USB_CHIPIDEA_HOST) && \
- !IS_ENABLED(CONFIG_USB_EHCI_MXC) && \
- !IS_ENABLED(CONFIG_USB_EHCI_HCD_OMAP) && \
- !IS_ENABLED(CONFIG_USB_EHCI_HCD_ORION) && \
- !IS_ENABLED(CONFIG_USB_EHCI_HCD_SPEAR) && \
- !IS_ENABLED(CONFIG_USB_EHCI_S5P) && \
- !IS_ENABLED(CONFIG_USB_EHCI_HCD_AT91) && \
- !IS_ENABLED(CONFIG_USB_EHCI_MSM) && \
- !defined(PLATFORM_DRIVER) && \
- !defined(PS3_SYSTEM_BUS_DRIVER) && \
- !defined(OF_PLATFORM_DRIVER) && \
- !defined(XILINX_OF_PLATFORM_DRIVER)
-#error "missing bus glue for ehci-hcd"
-#endif
-
static int __init ehci_hcd_init(void)
{
int retval = 0;
.extra_priv_size = sizeof(struct omap_hcd),
};
-static u64 omap_ehci_dma_mask = DMA_BIT_MASK(32);
-
/**
* ehci_hcd_omap_probe - initialize TI-based HCDs
*
* Since shared usb code relies on it, set it here for now.
* Once we have dma capability bindings this can go away.
*/
- if (!pdev->dev.dma_mask)
- pdev->dev.dma_mask = &omap_ehci_dma_mask;
+ if (!dev->dma_mask)
+ dev->dma_mask = &dev->coherent_dma_mask;
+ if (!dev->coherent_dma_mask)
+ dev->coherent_dma_mask = DMA_BIT_MASK(32);
hcd = usb_create_hcd(&ehci_omap_hc_driver, dev,
dev_name(dev));
}
}
-static u64 ehci_orion_dma_mask = DMA_BIT_MASK(32);
-
static int ehci_orion_drv_probe(struct platform_device *pdev)
{
struct orion_ehci_data *pd = pdev->dev.platform_data;
* now. Once we have dma capability bindings this can go away.
*/
if (!pdev->dev.dma_mask)
- pdev->dev.dma_mask = &ehci_orion_dma_mask;
+ pdev->dev.dma_mask = &pdev->dev.coherent_dma_mask;
+ if (!pdev->dev.coherent_dma_mask)
+ pdev->dev.coherent_dma_mask = DMA_BIT_MASK(32);
if (!request_mem_region(res->start, resource_size(res),
ehci_orion_hc_driver.description)) {
dev_err(dev, "can't request ehci vbus gpio %d", gpio);
}
-static u64 ehci_s5p_dma_mask = DMA_BIT_MASK(32);
-
static int s5p_ehci_probe(struct platform_device *pdev)
{
struct s5p_ehci_platdata *pdata = pdev->dev.platform_data;
* Once we move to full device tree support this will vanish off.
*/
if (!pdev->dev.dma_mask)
- pdev->dev.dma_mask = &ehci_s5p_dma_mask;
+ pdev->dev.dma_mask = &pdev->dev.coherent_dma_mask;
if (!pdev->dev.coherent_dma_mask)
pdev->dev.coherent_dma_mask = DMA_BIT_MASK(32);
if (IS_ERR(phy)) {
/* Fallback to pdata */
if (!pdata) {
+ usb_put_hcd(hcd);
dev_warn(&pdev->dev, "no platform data or transceiver defined\n");
return -EPROBE_DEFER;
} else {
}
static const unsigned char
-max_tt_usecs[] = { 125, 125, 125, 125, 125, 125, 125, 25 };
+max_tt_usecs[] = { 125, 125, 125, 125, 125, 125, 30, 0 };
/* carryover low/fullspeed bandwidth that crosses uframe boundries */
static inline void carryover_tt_bandwidth(unsigned short tt_usecs[8])
/* reschedule QH iff another request is queued */
if (!list_empty(&qh->qtd_list) && ehci->rh_state == EHCI_RH_RUNNING) {
rc = qh_schedule(ehci, qh);
+ if (rc == 0) {
+ qh_refresh(ehci, qh);
+ qh_link_periodic(ehci, qh);
+ }
/* An error here likely indicates handshake failure
* or no space left in the schedule. Neither fault
*
* FIXME kill the now-dysfunctional queued urbs
*/
- if (rc != 0)
+ else {
ehci_err(ehci, "can't reschedule qh %p, err %d\n",
qh, rc);
+ }
}
/* maybe turn off periodic schedule */
static SIMPLE_DEV_PM_OPS(ehci_spear_pm_ops, ehci_spear_drv_suspend,
ehci_spear_drv_resume);
-static u64 spear_ehci_dma_mask = DMA_BIT_MASK(32);
-
static int spear_ehci_hcd_drv_probe(struct platform_device *pdev)
{
struct usb_hcd *hcd ;
* Once we have dma capability bindings this can go away.
*/
if (!pdev->dev.dma_mask)
- pdev->dev.dma_mask = &spear_ehci_dma_mask;
+ pdev->dev.dma_mask = &pdev->dev.coherent_dma_mask;
+ if (!pdev->dev.coherent_dma_mask)
+ pdev->dev.coherent_dma_mask = DMA_BIT_MASK(32);
usbh_clk = devm_clk_get(&pdev->dev, NULL);
if (IS_ERR(usbh_clk)) {
writel(val, base + TEGRA_USB_PORTSC1);
}
-static u64 tegra_ehci_dma_mask = DMA_BIT_MASK(32);
-
static int tegra_ehci_probe(struct platform_device *pdev)
{
struct resource *res;
* Once we have dma capability bindings this can go away.
*/
if (!pdev->dev.dma_mask)
- pdev->dev.dma_mask = &tegra_ehci_dma_mask;
+ pdev->dev.dma_mask = &pdev->dev.coherent_dma_mask;
+ if (!pdev->dev.coherent_dma_mask)
+ pdev->dev.coherent_dma_mask = DMA_BIT_MASK(32);
setup_vbus_gpio(pdev, pdata);
int retval = 1;
unsigned long flags;
- /* if !USB_SUSPEND, root hub timers won't get shut down ... */
+ /* if !PM_RUNTIME, root hub timers won't get shut down ... */
if (!HC_IS_RUNNING(hcd->state))
return 0;
irq_res = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
if (!irq_res) {
pr_warning("isp1760: IRQ resource not available\n");
- return -ENODEV;
+ ret = -ENODEV;
+ goto cleanup;
}
+
irqflags |= irq_res->flags & IRQF_TRIGGER_MASK;
if (priv) {
MODULE_DEVICE_TABLE(of, at91_ohci_dt_ids);
-static u64 at91_ohci_dma_mask = DMA_BIT_MASK(32);
-
static int ohci_at91_of_init(struct platform_device *pdev)
{
struct device_node *np = pdev->dev.of_node;
* Once we have dma capability bindings this can go away.
*/
if (!pdev->dev.dma_mask)
- pdev->dev.dma_mask = &at91_ohci_dma_mask;
+ pdev->dev.dma_mask = &pdev->dev.coherent_dma_mask;
+ if (!pdev->dev.coherent_dma_mask)
+ pdev->dev.coherent_dma_mask = DMA_BIT_MASK(32);
pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
if (!pdata)
.start_port_reset = ohci_start_port_reset,
};
-static u64 ohci_exynos_dma_mask = DMA_BIT_MASK(32);
-
static int exynos_ohci_probe(struct platform_device *pdev)
{
struct exynos4_ohci_platdata *pdata = pdev->dev.platform_data;
* Once we move to full device tree support this will vanish off.
*/
if (!pdev->dev.dma_mask)
- pdev->dev.dma_mask = &ohci_exynos_dma_mask;
+ pdev->dev.dma_mask = &pdev->dev.coherent_dma_mask;
if (!pdev->dev.coherent_dma_mask)
pdev->dev.coherent_dma_mask = DMA_BIT_MASK(32);
urb->start_frame = frame;
}
} else if (ed->type == PIPE_ISOCHRONOUS) {
- u16 next = ohci_frame_no(ohci) + 2;
+ u16 next = ohci_frame_no(ohci) + 1;
u16 frame = ed->last_iso + ed->interval;
/* Behind the scheduling threshold? */
if (unlikely(tick_before(frame, next))) {
/* USB_ISO_ASAP: Round up to the first available slot */
- if (urb->transfer_flags & URB_ISO_ASAP)
+ if (urb->transfer_flags & URB_ISO_ASAP) {
frame += (next - frame + ed->interval - 1) &
-ed->interval;
* Not ASAP: Use the next slot in the stream. If
* the entire URB falls before the threshold, fail.
*/
- else if (tick_before(frame + ed->interval *
+ } else {
+ if (tick_before(frame + ed->interval *
(urb->number_of_packets - 1), next)) {
- retval = -EXDEV;
- usb_hcd_unlink_urb_from_ep(hcd, urb);
- goto fail;
- }
+ retval = -EXDEV;
+ usb_hcd_unlink_urb_from_ep(hcd, urb);
+ goto fail;
+ }
- /*
- * Some OHCI hardware doesn't handle late TDs
- * correctly. After retiring them it proceeds to
- * the next ED instead of the next TD. Therefore
- * we have to omit the late TDs entirely.
- */
- urb_priv->td_cnt = DIV_ROUND_UP(next - frame,
- ed->interval);
+ /*
+ * Some OHCI hardware doesn't handle late TDs
+ * correctly. After retiring them it proceeds
+ * to the next ED instead of the next TD.
+ * Therefore we have to omit the late TDs
+ * entirely.
+ */
+ urb_priv->td_cnt = DIV_ROUND_UP(
+ (u16) (next - frame),
+ ed->interval);
+ }
}
urb->start_frame = frame;
}
isp1301_i2c_client = isp1301_get_client(isp1301_node);
if (!isp1301_i2c_client) {
- ret = -EPROBE_DEFER;
- goto out;
+ return -EPROBE_DEFER;
}
pdev->dev.coherent_dma_mask = DMA_BIT_MASK(32);
if (usb_disabled()) {
dev_err(&pdev->dev, "USB is disabled\n");
ret = -ENODEV;
- goto out;
+ goto fail_disable;
}
/* Enable AHB slave USB clock, needed for further USB clock control */
if (IS_ERR(usb_pll_clk)) {
dev_err(&pdev->dev, "failed to acquire USB PLL\n");
ret = PTR_ERR(usb_pll_clk);
- goto out1;
+ goto fail_pll;
}
ret = clk_enable(usb_pll_clk);
if (ret < 0) {
dev_err(&pdev->dev, "failed to start USB PLL\n");
- goto out2;
+ goto fail_pllen;
}
ret = clk_set_rate(usb_pll_clk, 48000);
if (ret < 0) {
dev_err(&pdev->dev, "failed to set USB clock rate\n");
- goto out3;
+ goto fail_rate;
}
/* Enable USB device clock */
if (IS_ERR(usb_dev_clk)) {
dev_err(&pdev->dev, "failed to acquire USB DEV Clock\n");
ret = PTR_ERR(usb_dev_clk);
- goto out4;
+ goto fail_dev;
}
ret = clk_enable(usb_dev_clk);
if (ret < 0) {
dev_err(&pdev->dev, "failed to start USB DEV Clock\n");
- goto out5;
+ goto fail_deven;
}
/* Enable USB otg clocks */
if (IS_ERR(usb_otg_clk)) {
dev_err(&pdev->dev, "failed to acquire USB DEV Clock\n");
ret = PTR_ERR(usb_otg_clk);
- goto out6;
+ goto fail_otg;
}
__raw_writel(__raw_readl(USB_CTRL) | USB_HOST_NEED_CLK_EN, USB_CTRL);
ret = clk_enable(usb_otg_clk);
if (ret < 0) {
dev_err(&pdev->dev, "failed to start USB DEV Clock\n");
- goto out7;
+ goto fail_otgen;
}
isp1301_configure();
if (!hcd) {
dev_err(&pdev->dev, "Failed to allocate HC buffer\n");
ret = -ENOMEM;
- goto out8;
+ goto fail_hcd;
}
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
hcd->regs = devm_ioremap_resource(&pdev->dev, res);
if (IS_ERR(hcd->regs)) {
ret = PTR_ERR(hcd->regs);
- goto out8;
+ goto fail_resource;
}
hcd->rsrc_start = res->start;
hcd->rsrc_len = resource_size(res);
irq = platform_get_irq(pdev, 0);
if (irq < 0) {
ret = -ENXIO;
- goto out8;
+ goto fail_resource;
}
nxp_start_hc();
return ret;
nxp_stop_hc();
-out8:
+fail_resource:
usb_put_hcd(hcd);
-out7:
+fail_hcd:
clk_disable(usb_otg_clk);
-out6:
+fail_otgen:
clk_put(usb_otg_clk);
-out5:
+fail_otg:
clk_disable(usb_dev_clk);
-out4:
+fail_deven:
clk_put(usb_dev_clk);
-out3:
+fail_dev:
+fail_rate:
clk_disable(usb_pll_clk);
-out2:
+fail_pllen:
clk_put(usb_pll_clk);
-out1:
+fail_pll:
+fail_disable:
isp1301_i2c_client = NULL;
-out:
return ret;
}
/*-------------------------------------------------------------------------*/
-static u64 omap_ohci_dma_mask = DMA_BIT_MASK(32);
-
/*
* configure so an HC device and id are always provided
* always called with process context; sleeping is OK
* Since shared usb code relies on it, set it here for now.
* Once we have dma capability bindings this can go away.
*/
- if (!pdev->dev.dma_mask)
- pdev->dev.dma_mask = &omap_ohci_dma_mask;
+ if (!dev->dma_mask)
+ dev->dma_mask = &dev->coherent_dma_mask;
+ if (!dev->coherent_dma_mask)
+ dev->coherent_dma_mask = DMA_BIT_MASK(32);
hcd = usb_create_hcd(&ohci_omap3_hc_driver, dev,
dev_name(dev));
MODULE_DEVICE_TABLE(of, pxa_ohci_dt_ids);
-static u64 pxa_ohci_dma_mask = DMA_BIT_MASK(32);
-
static int ohci_pxa_of_init(struct platform_device *pdev)
{
struct device_node *np = pdev->dev.of_node;
* Once we have dma capability bindings this can go away.
*/
if (!pdev->dev.dma_mask)
- pdev->dev.dma_mask = &pxa_ohci_dma_mask;
+ pdev->dev.dma_mask = &pdev->dev.coherent_dma_mask;
+ if (!pdev->dev.coherent_dma_mask)
+ pdev->dev.coherent_dma_mask = DMA_BIT_MASK(32);
pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
if (!pdata)
.start_port_reset = ohci_start_port_reset,
};
-static u64 spear_ohci_dma_mask = DMA_BIT_MASK(32);
-
static int spear_ohci_hcd_drv_probe(struct platform_device *pdev)
{
const struct hc_driver *driver = &ohci_spear_hc_driver;
* Once we have dma capability bindings this can go away.
*/
if (!pdev->dev.dma_mask)
- pdev->dev.dma_mask = &spear_ohci_dma_mask;
+ pdev->dev.dma_mask = &pdev->dev.coherent_dma_mask;
+ if (!pdev->dev.coherent_dma_mask)
+ pdev->dev.coherent_dma_mask = DMA_BIT_MASK(32);
usbh_clk = devm_clk_get(&pdev->dev, NULL);
if (IS_ERR(usbh_clk)) {
int ports, i, retval = 1;
unsigned long flags;
- /* if !USB_SUSPEND, root hub timers won't get shut down ... */
+ /* if !PM_RUNTIME, root hub timers won't get shut down ... */
if (!HC_IS_RUNNING(hcd->state))
return 0;
* and usb-storage.
*
* TODO:
- * - usb suspend/resume triggered by sl811 (with USB_SUSPEND)
+ * - usb suspend/resume triggered by sl811 (with PM_RUNTIME)
* - various issues noted in the code
* - performance work; use both register banks; ...
* - use urb->iso_frame_desc[] with ISO transfers
/* auto-stop if nothing connected for 1 second */
if (any_ports_active(uhci))
uhci->rh_state = UHCI_RH_RUNNING;
- else if (time_after_eq(jiffies, uhci->auto_stop_time))
+ else if (time_after_eq(jiffies, uhci->auto_stop_time) &&
+ !uhci->wait_for_hp)
suspend_rh(uhci, UHCI_RH_AUTO_STOPPED);
break;
.hub_control = uhci_hub_control,
};
-static u64 platform_uhci_dma_mask = DMA_BIT_MASK(32);
-
static int uhci_hcd_platform_probe(struct platform_device *pdev)
{
struct usb_hcd *hcd;
* Once we have dma capability bindings this can go away.
*/
if (!pdev->dev.dma_mask)
- pdev->dev.dma_mask = &platform_uhci_dma_mask;
+ pdev->dev.dma_mask = &pdev->dev.coherent_dma_mask;
+ if (!pdev->dev.coherent_dma_mask)
+ pdev->dev.coherent_dma_mask = DMA_BIT_MASK(32);
hcd = usb_create_hcd(&uhci_platform_hc_driver, &pdev->dev,
pdev->name);
return -EINVAL; /* Can't change the period */
} else {
- next = uhci->frame_number + 2;
+ next = uhci->frame_number + 1;
/* Find the next unused frame */
if (list_empty(&qh->queue)) {
ep_ctx->ep_info2 |= cpu_to_le32(xhci_get_endpoint_type(udev, ep));
/* Set the max packet size and max burst */
+ max_packet = GET_MAX_PACKET(usb_endpoint_maxp(&ep->desc));
+ max_burst = 0;
switch (udev->speed) {
case USB_SPEED_SUPER:
- max_packet = usb_endpoint_maxp(&ep->desc);
- ep_ctx->ep_info2 |= cpu_to_le32(MAX_PACKET(max_packet));
/* dig out max burst from ep companion desc */
- max_packet = ep->ss_ep_comp.bMaxBurst;
- ep_ctx->ep_info2 |= cpu_to_le32(MAX_BURST(max_packet));
+ max_burst = ep->ss_ep_comp.bMaxBurst;
break;
case USB_SPEED_HIGH:
+ /* Some devices get this wrong */
+ if (usb_endpoint_xfer_bulk(&ep->desc))
+ max_packet = 512;
/* bits 11:12 specify the number of additional transaction
* opportunities per microframe (USB 2.0, section 9.6.6)
*/
usb_endpoint_xfer_int(&ep->desc)) {
max_burst = (usb_endpoint_maxp(&ep->desc)
& 0x1800) >> 11;
- ep_ctx->ep_info2 |= cpu_to_le32(MAX_BURST(max_burst));
}
- /* Fall through */
+ break;
case USB_SPEED_FULL:
case USB_SPEED_LOW:
- max_packet = GET_MAX_PACKET(usb_endpoint_maxp(&ep->desc));
- ep_ctx->ep_info2 |= cpu_to_le32(MAX_PACKET(max_packet));
break;
default:
BUG();
}
+ ep_ctx->ep_info2 |= cpu_to_le32(MAX_PACKET(max_packet) |
+ MAX_BURST(max_burst));
max_esit_payload = xhci_get_max_esit_payload(xhci, udev, ep);
ep_ctx->tx_info = cpu_to_le32(MAX_ESIT_PAYLOAD_FOR_EP(max_esit_payload));
}
spin_unlock_irqrestore(&xhci->lock, flags);
+ if (!xhci->rh_bw)
+ goto no_bw;
+
num_ports = HCS_MAX_PORTS(xhci->hcs_params1);
for (i = 0; i < num_ports; i++) {
struct xhci_interval_bw_table *bwt = &xhci->rh_bw[i].bw_table;
}
}
+no_bw:
xhci->num_usb2_ports = 0;
xhci->num_usb3_ports = 0;
xhci->num_active_eps = 0;
u32 page_size, temp;
int i;
+ INIT_LIST_HEAD(&xhci->lpm_failed_devs);
+ INIT_LIST_HEAD(&xhci->cancel_cmd_list);
+
page_size = xhci_readl(xhci, &xhci->op_regs->page_size);
xhci_dbg(xhci, "Supported page size register = 0x%x\n", page_size);
for (i = 0; i < 16; i++) {
xhci->cmd_ring = xhci_ring_alloc(xhci, 1, 1, TYPE_COMMAND, flags);
if (!xhci->cmd_ring)
goto fail;
- INIT_LIST_HEAD(&xhci->cancel_cmd_list);
xhci_dbg(xhci, "Allocated command ring at %p\n", xhci->cmd_ring);
xhci_dbg(xhci, "First segment DMA is 0x%llx\n",
(unsigned long long)xhci->cmd_ring->first_seg->dma);
if (xhci_setup_port_arrays(xhci, flags))
goto fail;
- INIT_LIST_HEAD(&xhci->lpm_failed_devs);
-
/* Enable USB 3.0 device notifications for function remote wake, which
* is necessary for allowing USB 3.0 devices to do remote wakeup from
* U3 (device suspend).
static int xhci_pci_suspend(struct usb_hcd *hcd, bool do_wakeup)
{
struct xhci_hcd *xhci = hcd_to_xhci(hcd);
+ struct pci_dev *pdev = to_pci_dev(hcd->self.controller);
+
+ /*
+ * Systems with the TI redriver that loses port status change events
+ * need to have the registers polled during D3, so avoid D3cold.
+ */
+ if (xhci_compliance_mode_recovery_timer_quirk_check())
+ pdev->no_d3cold = true;
return xhci_suspend(xhci);
}
* Systems:
* Vendor: Hewlett-Packard -> System Models: Z420, Z620 and Z820
*/
-static bool compliance_mode_recovery_timer_quirk_check(void)
+bool xhci_compliance_mode_recovery_timer_quirk_check(void)
{
const char *dmi_product_name, *dmi_sys_vendor;
xhci_dbg(xhci, "Finished xhci_init\n");
/* Initializing Compliance Mode Recovery Data If Needed */
- if (compliance_mode_recovery_timer_quirk_check()) {
+ if (xhci_compliance_mode_recovery_timer_quirk_check()) {
xhci->quirks |= XHCI_COMP_MODE_QUIRK;
compliance_mode_recovery_timer_init(xhci);
}
struct usb_hcd *hcd = xhci_to_hcd(xhci);
struct usb_hcd *secondary_hcd;
int retval = 0;
+ bool comp_timer_running = false;
/* Wait a bit if either of the roothubs need to settle from the
* transition into bus suspend.
/* If restore operation fails, re-initialize the HC during resume */
if ((temp & STS_SRE) || hibernated) {
+
+ if ((xhci->quirks & XHCI_COMP_MODE_QUIRK) &&
+ !(xhci_all_ports_seen_u0(xhci))) {
+ del_timer_sync(&xhci->comp_mode_recovery_timer);
+ xhci_dbg(xhci, "Compliance Mode Recovery Timer deleted!\n");
+ }
+
/* Let the USB core know _both_ roothubs lost power. */
usb_root_hub_lost_power(xhci->main_hcd->self.root_hub);
usb_root_hub_lost_power(xhci->shared_hcd->self.root_hub);
retval = xhci_init(hcd->primary_hcd);
if (retval)
return retval;
+ comp_timer_running = true;
+
xhci_dbg(xhci, "Start the primary HCD\n");
retval = xhci_run(hcd->primary_hcd);
if (!retval) {
* to suffer the Compliance Mode issue again. It doesn't matter if
* ports have entered previously to U0 before system's suspension.
*/
- if (xhci->quirks & XHCI_COMP_MODE_QUIRK)
+ if ((xhci->quirks & XHCI_COMP_MODE_QUIRK) && !comp_timer_running)
compliance_mode_recovery_timer_init(xhci);
/* Re-enable port polling. */
struct xhci_slot_ctx *xhci_get_slot_ctx(struct xhci_hcd *xhci, struct xhci_container_ctx *ctx);
struct xhci_ep_ctx *xhci_get_ep_ctx(struct xhci_hcd *xhci, struct xhci_container_ctx *ctx, unsigned int ep_index);
+/* xHCI quirks */
+bool xhci_compliance_mode_recovery_timer_quirk_check(void);
+
#endif /* __LINUX_XHCI_HCD_H */
if (!config) {
dev_err(&pdev->dev,
"failed to allocate musb hdrc config\n");
+ ret = -ENOMEM;
goto err2;
}
void __iomem *mbase = musb->mregs;
struct dma_channel *dma;
bool transfer_pending = false;
- static bool use_sg;
musb_ep_select(mbase, epnum);
tx_csr = musb_readw(epio, MUSB_TXCSR);
* NULL.
*/
if (!urb->transfer_buffer)
- use_sg = true;
+ qh->use_sg = true;
- if (use_sg) {
+ if (qh->use_sg) {
/* sg_miter_start is already done in musb_ep_program */
if (!sg_miter_next(&qh->sg_miter)) {
dev_err(musb->controller, "error: sg list empty\n");
qh->segsize = length;
- if (use_sg) {
+ if (qh->use_sg) {
if (offset + length >= urb->transfer_buffer_length)
- use_sg = false;
+ qh->use_sg = false;
}
musb_ep_select(mbase, epnum);
bool done = false;
u32 status;
struct dma_channel *dma;
- static bool use_sg;
unsigned int sg_flags = SG_MITER_ATOMIC | SG_MITER_TO_SG;
musb_ep_select(mbase, epnum);
* NULL.
*/
if (!urb->transfer_buffer) {
- use_sg = true;
+ qh->use_sg = true;
sg_miter_start(&qh->sg_miter, urb->sg, 1,
sg_flags);
}
- if (use_sg) {
+ if (qh->use_sg) {
if (!sg_miter_next(&qh->sg_miter)) {
dev_err(musb->controller, "error: sg list empty\n");
sg_miter_stop(&qh->sg_miter);
urb->actual_length += xfer_len;
qh->offset += xfer_len;
if (done) {
- if (use_sg)
- use_sg = false;
+ if (qh->use_sg)
+ qh->use_sg = false;
if (urb->status == -EINPROGRESS)
urb->status = status;
u16 frame; /* for periodic schedule */
unsigned iso_idx; /* in urb->iso_frame_desc[] */
struct sg_mapping_iter sg_miter; /* for highmem in PIO mode */
+ bool use_sg; /* to track urb using sglist */
};
/* map from control or bulk queue head to the first qh on that ring */
glue->control_otghs = omap_get_control_dev();
if (IS_ERR(glue->control_otghs)) {
dev_vdbg(&pdev->dev, "Failed to get control device\n");
- return -ENODEV;
+ ret = PTR_ERR(glue->control_otghs);
+ goto err2;
}
} else {
glue->control_otghs = ERR_PTR(-ENODEV);
config FSL_USB2_OTG
bool "Freescale USB OTG Transceiver Driver"
- depends on USB_EHCI_FSL && USB_FSL_USB2 && USB_SUSPEND
+ depends on USB_EHCI_FSL && USB_FSL_USB2 && PM_RUNTIME
select USB_OTG
help
Enable this to support Freescale USB OTG transceiver.
tristate "NXP ISP1301 USB transceiver support"
depends on USB || USB_GADGET
depends on I2C
- select USB_OTG_UTILS
help
Say Y here to add support for the NXP ISP1301 USB transceiver driver.
This chip is typically used as USB transceiver for USB host, gadget
config USB_MV_OTG
tristate "Marvell USB OTG support"
- depends on USB_EHCI_MV && USB_MV_UDC && USB_SUSPEND
+ depends on USB_EHCI_MV && USB_MV_UDC && PM_RUNTIME
select USB_OTG
help
Say Y here if you want to build Marvell USB OTG transciever
else if (ab->mode == USB_PERIPHERAL)
ab8500_usb_peri_phy_dis(ab);
- platform_set_drvdata(pdev, NULL);
-
return 0;
}
/* initialize the otg structure */
fsl_otg_tc->phy.label = DRIVER_DESC;
+ fsl_otg_tc->phy.dev = &pdev->dev;
fsl_otg_tc->phy.set_power = fsl_otg_set_power;
fsl_otg_tc->phy.otg->phy = &fsl_otg_tc->phy;
platform_set_drvdata(pdev, gpio_vbus);
gpio_vbus->dev = &pdev->dev;
gpio_vbus->phy.label = "gpio-vbus";
+ gpio_vbus->phy.dev = gpio_vbus->dev;
gpio_vbus->phy.set_power = gpio_vbus_set_power;
gpio_vbus->phy.set_suspend = gpio_vbus_set_suspend;
gpio_vbus->phy.state = OTG_STATE_UNDEFINED;
gpio_free(pdata->gpio_pullup);
gpio_free(pdata->gpio_vbus);
err_gpio:
- platform_set_drvdata(pdev, NULL);
kfree(gpio_vbus->phy.otg);
kfree(gpio_vbus);
return err;
if (gpio_is_valid(pdata->gpio_pullup))
gpio_free(pdata->gpio_pullup);
gpio_free(gpio);
- platform_set_drvdata(pdev, NULL);
kfree(gpio_vbus->phy.otg);
kfree(gpio_vbus);
mutex_init(&isp->mutex);
phy = &isp->phy;
+ phy->dev = &client->dev;
phy->label = DRV_NAME;
phy->init = isp1301_phy_init;
phy->set_vbus = isp1301_phy_set_vbus;
mv_otg_disable(mvotg);
usb_remove_phy(&mvotg->phy);
- platform_set_drvdata(pdev, NULL);
return 0;
}
flush_workqueue(mvotg->qwork);
destroy_workqueue(mvotg->qwork);
- platform_set_drvdata(pdev, NULL);
-
return retval;
}
mxs_phy->phy.set_suspend = mxs_phy_suspend;
mxs_phy->phy.notify_connect = mxs_phy_on_connect;
mxs_phy->phy.notify_disconnect = mxs_phy_on_disconnect;
+ mxs_phy->phy.type = USB_PHY_TYPE_USB2;
ATOMIC_INIT_NOTIFIER_HEAD(&mxs_phy->phy.notifier);
usb_remove_phy(&mxs_phy->phy);
- platform_set_drvdata(pdev, NULL);
-
return 0;
}
usb_remove_phy(&nop->phy);
- platform_set_drvdata(pdev, NULL);
-
return 0;
}
#define DRIVER_NAME "ark3116"
/* usb timeout of 1 second */
-#define ARK_TIMEOUT (1*HZ)
+#define ARK_TIMEOUT 1000
static const struct usb_device_id id_table[] = {
{ USB_DEVICE(0x6547, 0x0232) },
static const struct usb_device_id id_table_cyphidcomrs232[] = {
{ USB_DEVICE(VENDOR_ID_CYPRESS, PRODUCT_ID_CYPHIDCOM) },
{ USB_DEVICE(VENDOR_ID_POWERCOM, PRODUCT_ID_UPS) },
+ { USB_DEVICE(VENDOR_ID_FRWD, PRODUCT_ID_CYPHIDCOM_FRWD) },
{ } /* Terminating entry */
};
{ USB_DEVICE(VENDOR_ID_DELORME, PRODUCT_ID_EARTHMATEUSB_LT20) },
{ USB_DEVICE(VENDOR_ID_CYPRESS, PRODUCT_ID_CYPHIDCOM) },
{ USB_DEVICE(VENDOR_ID_POWERCOM, PRODUCT_ID_UPS) },
+ { USB_DEVICE(VENDOR_ID_FRWD, PRODUCT_ID_CYPHIDCOM_FRWD) },
{ USB_DEVICE(VENDOR_ID_DAZZLE, PRODUCT_ID_CA42) },
{ } /* Terminating entry */
};
* Cypress serial helper functions
*****************************************************************************/
+/* FRWD Dongle hidcom needs to skip reset and speed checks */
+static inline bool is_frwd(struct usb_device *dev)
+{
+ return ((le16_to_cpu(dev->descriptor.idVendor) == VENDOR_ID_FRWD) &&
+ (le16_to_cpu(dev->descriptor.idProduct) == PRODUCT_ID_CYPHIDCOM_FRWD));
+}
static int analyze_baud_rate(struct usb_serial_port *port, speed_t new_rate)
{
if (unstable_bauds)
return new_rate;
+ /* FRWD Dongle uses 115200 bps */
+ if (is_frwd(port->serial->dev))
+ return new_rate;
+
/*
* The general purpose firmware for the Cypress M8 allows for
* a maximum speed of 57600bps (I have no idea whether DeLorme
return -ENOMEM;
}
- usb_reset_configuration(serial->dev);
+ /* Skip reset for FRWD device. It is a workaound:
+ device hangs if it receives SET_CONFIGURE in Configured
+ state. */
+ if (!is_frwd(serial->dev))
+ usb_reset_configuration(serial->dev);
priv->cmd_ctrl = 0;
priv->line_control = 0;
#define VENDOR_ID_CYPRESS 0x04b4
#define PRODUCT_ID_CYPHIDCOM 0x5500
+/* FRWD Dongle - a GPS sports watch */
+#define VENDOR_ID_FRWD 0x6737
+#define PRODUCT_ID_CYPHIDCOM_FRWD 0x0001
+
/* Powercom UPS, chip CY7C63723 */
#define VENDOR_ID_POWERCOM 0x0d9f
#define PRODUCT_ID_UPS 0x0002
{ USB_DEVICE(FTDI_VID, FTDI_OPENDCC_GBM_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_OPENDCC_GBM_BOOST_PID) },
{ USB_DEVICE(NEWPORT_VID, NEWPORT_AGILIS_PID) },
+ { USB_DEVICE(NEWPORT_VID, NEWPORT_CONEX_CC_PID) },
+ { USB_DEVICE(NEWPORT_VID, NEWPORT_CONEX_AGP_PID) },
{ USB_DEVICE(INTERBIOMETRICS_VID, INTERBIOMETRICS_IOBOARD_PID) },
{ USB_DEVICE(INTERBIOMETRICS_VID, INTERBIOMETRICS_MINI_IOBOARD_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_SPROG_II) },
static int ftdi_ioctl(struct tty_struct *tty,
unsigned int cmd, unsigned long arg);
static void ftdi_break_ctl(struct tty_struct *tty, int break_state);
-static int ftdi_chars_in_buffer(struct tty_struct *tty);
-static int ftdi_get_modem_status(struct tty_struct *tty,
+static bool ftdi_tx_empty(struct usb_serial_port *port);
+static int ftdi_get_modem_status(struct usb_serial_port *port,
unsigned char status[2]);
static unsigned short int ftdi_232am_baud_base_to_divisor(int baud, int base);
.ioctl = ftdi_ioctl,
.set_termios = ftdi_set_termios,
.break_ctl = ftdi_break_ctl,
- .chars_in_buffer = ftdi_chars_in_buffer,
+ .tx_empty = ftdi_tx_empty,
};
static struct usb_serial_driver * const serial_drivers[] = {
}
-static int ftdi_chars_in_buffer(struct tty_struct *tty)
+static bool ftdi_tx_empty(struct usb_serial_port *port)
{
- struct usb_serial_port *port = tty->driver_data;
- int chars;
unsigned char buf[2];
int ret;
- chars = usb_serial_generic_chars_in_buffer(tty);
- if (chars)
- goto out;
-
- /* Check if hardware buffer is empty. */
- ret = ftdi_get_modem_status(tty, buf);
+ ret = ftdi_get_modem_status(port, buf);
if (ret == 2) {
if (!(buf[1] & FTDI_RS_TEMT))
- chars = 1;
+ return false;
}
-out:
- dev_dbg(&port->dev, "%s - %d\n", __func__, chars);
- return chars;
+ return true;
}
/* old_termios contains the original termios settings and tty->termios contains
* Returns the number of status bytes retrieved (device dependant), or
* negative error code.
*/
-static int ftdi_get_modem_status(struct tty_struct *tty,
+static int ftdi_get_modem_status(struct usb_serial_port *port,
unsigned char status[2])
{
- struct usb_serial_port *port = tty->driver_data;
struct ftdi_private *priv = usb_get_serial_port_data(port);
unsigned char *buf;
int len;
unsigned char buf[2];
int ret;
- ret = ftdi_get_modem_status(tty, buf);
+ ret = ftdi_get_modem_status(port, buf);
if (ret < 0)
return ret;
*/
#define NEWPORT_VID 0x104D
#define NEWPORT_AGILIS_PID 0x3000
+#define NEWPORT_CONEX_CC_PID 0x3002
+#define NEWPORT_CONEX_AGP_PID 0x3006
/* Interbiometrics USB I/O Board */
/* Developed for Interbiometrics by Rudolf Gugler */
}
EXPORT_SYMBOL_GPL(usb_serial_generic_chars_in_buffer);
+void usb_serial_generic_wait_until_sent(struct tty_struct *tty, long timeout)
+{
+ struct usb_serial_port *port = tty->driver_data;
+ unsigned int bps;
+ unsigned long period;
+ unsigned long expire;
+
+ bps = tty_get_baud_rate(tty);
+ if (!bps)
+ bps = 9600; /* B0 */
+ /*
+ * Use a poll-period of roughly the time it takes to send one
+ * character or at least one jiffy.
+ */
+ period = max_t(unsigned long, (10 * HZ / bps), 1);
+ period = min_t(unsigned long, period, timeout);
+
+ dev_dbg(&port->dev, "%s - timeout = %u ms, period = %u ms\n",
+ __func__, jiffies_to_msecs(timeout),
+ jiffies_to_msecs(period));
+ expire = jiffies + timeout;
+ while (!port->serial->type->tx_empty(port)) {
+ schedule_timeout_interruptible(period);
+ if (signal_pending(current))
+ break;
+ if (time_after(jiffies, expire))
+ break;
+ }
+}
+EXPORT_SYMBOL_GPL(usb_serial_generic_wait_until_sent);
+
static int usb_serial_generic_submit_read_urb(struct usb_serial_port *port,
int index, gfp_t mem_flags)
{
struct edgeport_port *edge_port = usb_get_serial_port_data(port);
int chars = 0;
unsigned long flags;
- int ret;
-
if (edge_port == NULL)
return 0;
chars = kfifo_len(&edge_port->write_fifo);
spin_unlock_irqrestore(&edge_port->ep_lock, flags);
- if (!chars) {
- ret = tx_active(edge_port);
- if (ret > 0)
- chars = ret;
- }
-
dev_dbg(&port->dev, "%s - returns %d\n", __func__, chars);
return chars;
}
+static bool edge_tx_empty(struct usb_serial_port *port)
+{
+ struct edgeport_port *edge_port = usb_get_serial_port_data(port);
+ int ret;
+
+ ret = tx_active(edge_port);
+ if (ret > 0)
+ return false;
+
+ return true;
+}
+
static void edge_throttle(struct tty_struct *tty)
{
struct usb_serial_port *port = tty->driver_data;
.write = edge_write,
.write_room = edge_write_room,
.chars_in_buffer = edge_chars_in_buffer,
+ .tx_empty = edge_tx_empty,
.break_ctl = edge_break,
.read_int_callback = edge_interrupt_callback,
.read_bulk_callback = edge_bulk_in_callback,
.write = edge_write,
.write_room = edge_write_room,
.chars_in_buffer = edge_chars_in_buffer,
+ .tx_empty = edge_tx_empty,
.break_ctl = edge_break,
.read_int_callback = edge_interrupt_callback,
.read_bulk_callback = edge_bulk_in_callback,
usb_bulk_msg(serial->dev,
usb_sndbulkpipe(serial->dev,
port->bulk_out_endpointAddress), buf,
- count, &actual, HZ * 1);
+ count, &actual, 1000);
if (status != IUU_OPERATION_OK)
dev_dbg(&port->dev, "%s - error = %2x\n", __func__, status);
usb_bulk_msg(serial->dev,
usb_rcvbulkpipe(serial->dev,
port->bulk_in_endpointAddress), buf,
- count, &actual, HZ * 1);
+ count, &actual, 1000);
if (status != IUU_OPERATION_OK)
dev_dbg(&port->dev, "%s - error = %2x\n", __func__, status);
struct keyspan_serial_private *s_priv;
struct keyspan_port_private *p_priv;
const struct keyspan_device_details *d_details;
- int outcont_urb;
struct urb *this_urb;
int device_port, err;
d_details = s_priv->device_details;
device_port = port->number - port->serial->minor;
- outcont_urb = d_details->outcont_endpoints[port->number];
this_urb = p_priv->outcont_urb;
dev_dbg(&port->dev, "%s - endpoint %d\n", __func__, usb_pipeendpoint(this_urb->pipe));
err = usb_submit_urb(this_urb, GFP_ATOMIC);
if (err != 0)
dev_dbg(&port->dev, "%s - usb_submit_urb(setup) failed (%d)\n", __func__, err);
-#if 0
- else {
- dev_dbg(&port->dev, "%s - usb_submit_urb(%d) OK %d bytes (end %d)\n", __func__
- outcont_urb, this_urb->transfer_buffer_length,
- usb_pipeendpoint(this_urb->pipe));
- }
-#endif
-
return 0;
}
#define DRIVER_DESC "Moschip USB Serial Driver"
/* default urb timeout */
-#define MOS_WDR_TIMEOUT (HZ * 5)
+#define MOS_WDR_TIMEOUT 5000
#define MOS_MAX_PORT 0x02
#define MOS_WRITE 0x0E
__u8 requesttype = (__u8)0xc0;
__u16 index = get_reg_index(reg);
__u16 value = get_reg_value(reg, serial_portnum);
- int status = usb_control_msg(usbdev, pipe, request, requesttype, value,
- index, data, 1, MOS_WDR_TIMEOUT);
- if (status < 0)
+ u8 *buf;
+ int status;
+
+ buf = kmalloc(1, GFP_KERNEL);
+ if (!buf)
+ return -ENOMEM;
+
+ status = usb_control_msg(usbdev, pipe, request, requesttype, value,
+ index, buf, 1, MOS_WDR_TIMEOUT);
+ if (status == 1)
+ *data = *buf;
+ else if (status < 0)
dev_err(&usbdev->dev,
"mos7720: usb_control_msg() failed: %d", status);
+ kfree(buf);
+
return status;
}
mos7720_port->shadowMCR |= (UART_MCR_XONANY);
/* To set hardware flow control to the specified *
* serial port, in SP1/2_CONTROL_REG */
- if (port->number)
+ if (port_number)
write_mos_reg(serial, dummy, SP_CONTROL_REG, 0x01);
else
write_mos_reg(serial, dummy, SP_CONTROL_REG, 0x02);
/* setting configuration feature to one */
usb_control_msg(serial->dev, usb_sndctrlpipe(serial->dev, 0),
- (__u8)0x03, 0x00, 0x01, 0x00, NULL, 0x00, 5*HZ);
+ (__u8)0x03, 0x00, 0x01, 0x00, NULL, 0x00, 5000);
/* start the interrupt urb */
ret_val = usb_submit_urb(serial->port[0]->interrupt_in_urb, GFP_KERNEL);
/* wait for synchronous usb calls to return */
if (mos_parport->msg_pending)
wait_for_completion_timeout(&mos_parport->syncmsg_compl,
- MOS_WDR_TIMEOUT);
+ msecs_to_jiffies(MOS_WDR_TIMEOUT));
parport_remove_port(mos_parport->pp);
usb_set_serial_data(serial, NULL);
static int mos7810_check(struct usb_serial *serial)
{
int i, pass_count = 0;
+ u8 *buf;
__u16 data = 0, mcr_data = 0;
__u16 test_pattern = 0x55AA;
+ int res;
+
+ buf = kmalloc(VENDOR_READ_LENGTH, GFP_KERNEL);
+ if (!buf)
+ return 0; /* failed to identify 7810 */
/* Store MCR setting */
- usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0),
+ res = usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0),
MCS_RDREQ, MCS_RD_RTYPE, 0x0300, MODEM_CONTROL_REGISTER,
- &mcr_data, VENDOR_READ_LENGTH, MOS_WDR_TIMEOUT);
+ buf, VENDOR_READ_LENGTH, MOS_WDR_TIMEOUT);
+ if (res == VENDOR_READ_LENGTH)
+ mcr_data = *buf;
for (i = 0; i < 16; i++) {
/* Send the 1-bit test pattern out to MCS7810 test pin */
MODEM_CONTROL_REGISTER, NULL, 0, MOS_WDR_TIMEOUT);
/* Read the test pattern back */
- usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0),
- MCS_RDREQ, MCS_RD_RTYPE, 0, GPIO_REGISTER, &data,
- VENDOR_READ_LENGTH, MOS_WDR_TIMEOUT);
+ res = usb_control_msg(serial->dev,
+ usb_rcvctrlpipe(serial->dev, 0), MCS_RDREQ,
+ MCS_RD_RTYPE, 0, GPIO_REGISTER, buf,
+ VENDOR_READ_LENGTH, MOS_WDR_TIMEOUT);
+ if (res == VENDOR_READ_LENGTH)
+ data = *buf;
/* If this is a MCS7810 device, both test patterns must match */
if (((test_pattern >> i) ^ (~data >> 1)) & 0x0001)
MCS_WR_RTYPE, 0x0300 | mcr_data, MODEM_CONTROL_REGISTER, NULL,
0, MOS_WDR_TIMEOUT);
+ kfree(buf);
+
if (pass_count == 16)
return 1;
static int mos7840_calc_num_ports(struct usb_serial *serial)
{
__u16 data = 0x00;
+ u8 *buf;
int mos7840_num_ports;
- usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0),
- MCS_RDREQ, MCS_RD_RTYPE, 0, GPIO_REGISTER, &data,
- VENDOR_READ_LENGTH, MOS_WDR_TIMEOUT);
+ buf = kzalloc(VENDOR_READ_LENGTH, GFP_KERNEL);
+ if (buf) {
+ usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0),
+ MCS_RDREQ, MCS_RD_RTYPE, 0, GPIO_REGISTER, buf,
+ VENDOR_READ_LENGTH, MOS_WDR_TIMEOUT);
+ data = *buf;
+ kfree(buf);
+ }
if (serial->dev->descriptor.idProduct == MOSCHIP_DEVICE_ID_7810 ||
serial->dev->descriptor.idProduct == MOSCHIP_DEVICE_ID_7820) {
#define DELL_PRODUCT_5800_MINICARD_VZW 0x8195 /* Novatel E362 */
#define DELL_PRODUCT_5800_V2_MINICARD_VZW 0x8196 /* Novatel E362 */
+#define DELL_PRODUCT_5804_MINICARD_ATT 0x819b /* Novatel E371 */
#define KYOCERA_VENDOR_ID 0x0c88
#define KYOCERA_PRODUCT_KPC650 0x17da
#define ZTE_PRODUCT_MF622 0x0001
#define ZTE_PRODUCT_MF628 0x0015
#define ZTE_PRODUCT_MF626 0x0031
-#define ZTE_PRODUCT_CDMA_TECH 0xfffe
-#define ZTE_PRODUCT_AC8710 0xfff1
-#define ZTE_PRODUCT_AC2726 0xfff5
-#define ZTE_PRODUCT_AC8710T 0xffff
#define ZTE_PRODUCT_MC2718 0xffe8
-#define ZTE_PRODUCT_AD3812 0xffeb
-#define ZTE_PRODUCT_MC2716 0xffed
#define BENQ_VENDOR_ID 0x04a5
#define BENQ_PRODUCT_H10 0x4068
#define CINTERION_PRODUCT_EU3_E 0x0051
#define CINTERION_PRODUCT_EU3_P 0x0052
#define CINTERION_PRODUCT_PH8 0x0053
-#define CINTERION_PRODUCT_AH6 0x0055
-#define CINTERION_PRODUCT_PLS8 0x0060
+#define CINTERION_PRODUCT_AHXX 0x0055
+#define CINTERION_PRODUCT_PLXX 0x0060
/* Olivetti products */
#define OLIVETTI_VENDOR_ID 0x0b3c
.reserved = BIT(4),
};
-static const struct option_blacklist_info zte_ad3812_z_blacklist = {
- .sendsetup = BIT(0) | BIT(1) | BIT(2),
-};
-
static const struct option_blacklist_info zte_mc2718_z_blacklist = {
.sendsetup = BIT(1) | BIT(2) | BIT(3) | BIT(4),
};
-static const struct option_blacklist_info zte_mc2716_z_blacklist = {
- .sendsetup = BIT(1) | BIT(2) | BIT(3),
-};
-
static const struct option_blacklist_info huawei_cdc12_blacklist = {
.reserved = BIT(1) | BIT(2),
};
.driver_info = (kernel_ulong_t) &huawei_cdc12_blacklist },
{ USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_K3765, 0xff, 0xff, 0xff),
.driver_info = (kernel_ulong_t) &huawei_cdc12_blacklist },
+ { USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0x14ac, 0xff, 0xff, 0xff), /* Huawei E1820 */
+ .driver_info = (kernel_ulong_t) &net_intf1_blacklist },
{ USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_K4605, 0xff, 0xff, 0xff),
.driver_info = (kernel_ulong_t) &huawei_cdc12_blacklist },
{ USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0xff, 0xff) },
{ USB_DEVICE(DELL_VENDOR_ID, DELL_PRODUCT_5730_MINICARD_VZW) }, /* Dell Wireless 5730 Mobile Broadband EVDO/HSPA Mini-Card */
{ USB_DEVICE_AND_INTERFACE_INFO(DELL_VENDOR_ID, DELL_PRODUCT_5800_MINICARD_VZW, 0xff, 0xff, 0xff) },
{ USB_DEVICE_AND_INTERFACE_INFO(DELL_VENDOR_ID, DELL_PRODUCT_5800_V2_MINICARD_VZW, 0xff, 0xff, 0xff) },
+ { USB_DEVICE_AND_INTERFACE_INFO(DELL_VENDOR_ID, DELL_PRODUCT_5804_MINICARD_ATT, 0xff, 0xff, 0xff) },
{ USB_DEVICE(ANYDATA_VENDOR_ID, ANYDATA_PRODUCT_ADU_E100A) }, /* ADU-E100, ADU-310 */
{ USB_DEVICE(ANYDATA_VENDOR_ID, ANYDATA_PRODUCT_ADU_500A) },
{ USB_DEVICE(ANYDATA_VENDOR_ID, ANYDATA_PRODUCT_ADU_620UW) },
{ USB_DEVICE_INTERFACE_CLASS(BANDRICH_VENDOR_ID, BANDRICH_PRODUCT_1012, 0xff) },
{ USB_DEVICE(KYOCERA_VENDOR_ID, KYOCERA_PRODUCT_KPC650) },
{ USB_DEVICE(KYOCERA_VENDOR_ID, KYOCERA_PRODUCT_KPC680) },
- { USB_DEVICE(QUALCOMM_VENDOR_ID, 0x6000)}, /* ZTE AC8700 */
{ USB_DEVICE(QUALCOMM_VENDOR_ID, 0x6613)}, /* Onda H600/ZTE MF330 */
{ USB_DEVICE(QUALCOMM_VENDOR_ID, 0x9000)}, /* SIMCom SIM5218 */
{ USB_DEVICE(CMOTECH_VENDOR_ID, CMOTECH_PRODUCT_6280) }, /* BP3-USB & BP3-EXT HSDPA */
.driver_info = (kernel_ulong_t)&net_intf4_blacklist },
{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0330, 0xff, 0xff, 0xff) },
{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0395, 0xff, 0xff, 0xff) },
+ { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0412, 0xff, 0xff, 0xff), /* Telewell TW-LTE 4G */
+ .driver_info = (kernel_ulong_t)&net_intf4_blacklist },
{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0414, 0xff, 0xff, 0xff) },
{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0417, 0xff, 0xff, 0xff) },
{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1008, 0xff, 0xff, 0xff),
{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0178, 0xff, 0xff, 0xff),
.driver_info = (kernel_ulong_t)&net_intf3_blacklist },
- { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_CDMA_TECH, 0xff, 0xff, 0xff) },
- { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_AC8710, 0xff, 0xff, 0xff) },
- { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_AC2726, 0xff, 0xff, 0xff) },
- { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_AC8710T, 0xff, 0xff, 0xff) },
+ /* NOTE: most ZTE CDMA devices should be driven by zte_ev, not option */
{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_MC2718, 0xff, 0xff, 0xff),
.driver_info = (kernel_ulong_t)&zte_mc2718_z_blacklist },
- { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_AD3812, 0xff, 0xff, 0xff),
- .driver_info = (kernel_ulong_t)&zte_ad3812_z_blacklist },
- { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_MC2716, 0xff, 0xff, 0xff),
- .driver_info = (kernel_ulong_t)&zte_mc2716_z_blacklist },
{ USB_VENDOR_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0xff, 0x02, 0x01) },
{ USB_VENDOR_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0xff, 0x02, 0x05) },
{ USB_VENDOR_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0xff, 0x86, 0x10) },
{ USB_DEVICE(CINTERION_VENDOR_ID, CINTERION_PRODUCT_EU3_E) },
{ USB_DEVICE(CINTERION_VENDOR_ID, CINTERION_PRODUCT_EU3_P) },
{ USB_DEVICE(CINTERION_VENDOR_ID, CINTERION_PRODUCT_PH8) },
- { USB_DEVICE(CINTERION_VENDOR_ID, CINTERION_PRODUCT_AH6) },
- { USB_DEVICE(CINTERION_VENDOR_ID, CINTERION_PRODUCT_PLS8) },
+ { USB_DEVICE(CINTERION_VENDOR_ID, CINTERION_PRODUCT_AHXX) },
+ { USB_DEVICE(CINTERION_VENDOR_ID, CINTERION_PRODUCT_PLXX),
+ .driver_info = (kernel_ulong_t)&net_intf4_blacklist },
{ USB_DEVICE(CINTERION_VENDOR_ID, CINTERION_PRODUCT_HC28_MDM) },
{ USB_DEVICE(CINTERION_VENDOR_ID, CINTERION_PRODUCT_HC28_MDMNET) },
{ USB_DEVICE(SIEMENS_VENDOR_ID, CINTERION_PRODUCT_HC25_MDM) },
{USB_DEVICE(0x1199, 0x901b)}, /* Sierra Wireless MC7770 */
{USB_DEVICE(0x12D1, 0x14F0)}, /* Sony Gobi 3000 QDL */
{USB_DEVICE(0x12D1, 0x14F1)}, /* Sony Gobi 3000 Composite */
+ {USB_DEVICE(0x0AF0, 0x8120)}, /* Option GTM681W */
/* non Gobi Qualcomm serial devices */
{USB_DEVICE_INTERFACE_NUMBER(0x0f3d, 0x68a2, 0)}, /* Sierra Wireless MC7700 Device Management */
const unsigned char *data, int count);
static int ti_write_room(struct tty_struct *tty);
static int ti_chars_in_buffer(struct tty_struct *tty);
+static bool ti_tx_empty(struct usb_serial_port *port);
static void ti_throttle(struct tty_struct *tty);
static void ti_unthrottle(struct tty_struct *tty);
static int ti_ioctl(struct tty_struct *tty,
.write = ti_write,
.write_room = ti_write_room,
.chars_in_buffer = ti_chars_in_buffer,
+ .tx_empty = ti_tx_empty,
.throttle = ti_throttle,
.unthrottle = ti_unthrottle,
.ioctl = ti_ioctl,
.write = ti_write,
.write_room = ti_write_room,
.chars_in_buffer = ti_chars_in_buffer,
+ .tx_empty = ti_tx_empty,
.throttle = ti_throttle,
.unthrottle = ti_unthrottle,
.ioctl = ti_ioctl,
struct ti_port *tport = usb_get_serial_port_data(port);
int chars = 0;
unsigned long flags;
- int ret;
- u8 lsr;
if (tport == NULL)
return 0;
chars = kfifo_len(&tport->write_fifo);
spin_unlock_irqrestore(&tport->tp_lock, flags);
- if (!chars) {
- ret = ti_get_lsr(tport, &lsr);
- if (!ret && !(lsr & TI_LSR_TX_EMPTY))
- chars = 1;
- }
-
dev_dbg(&port->dev, "%s - returns %d\n", __func__, chars);
return chars;
}
+static bool ti_tx_empty(struct usb_serial_port *port)
+{
+ struct ti_port *tport = usb_get_serial_port_data(port);
+ int ret;
+ u8 lsr;
+
+ ret = ti_get_lsr(tport, &lsr);
+ if (!ret && !(lsr & TI_LSR_TX_EMPTY))
+ return false;
+
+ return true;
+}
static void ti_throttle(struct tty_struct *tty)
{
{
struct usb_serial_port *port = tty->driver_data;
struct usb_serial *serial = port->serial;
- int count = 0;
dev_dbg(tty->dev, "%s\n", __func__);
- mutex_lock(&serial->disc_mutex);
- /* if the device was unplugged then any remaining characters
- fell out of the connector ;) */
if (serial->disconnected)
- count = 0;
- else
- count = serial->type->chars_in_buffer(tty);
- mutex_unlock(&serial->disc_mutex);
+ return 0;
- return count;
+ return serial->type->chars_in_buffer(tty);
+}
+
+static void serial_wait_until_sent(struct tty_struct *tty, int timeout)
+{
+ struct usb_serial_port *port = tty->driver_data;
+ struct usb_serial *serial = port->serial;
+
+ dev_dbg(tty->dev, "%s\n", __func__);
+
+ if (!port->serial->type->wait_until_sent)
+ return;
+
+ mutex_lock(&serial->disc_mutex);
+ if (!serial->disconnected)
+ port->serial->type->wait_until_sent(tty, timeout);
+ mutex_unlock(&serial->disc_mutex);
}
static void serial_throttle(struct tty_struct *tty)
unsigned int cmd, unsigned long arg)
{
struct usb_serial_port *port = tty->driver_data;
- int retval = -ENODEV;
+ int retval = -ENOIOCTLCMD;
dev_dbg(tty->dev, "%s - cmd 0x%.4x\n", __func__, cmd);
default:
if (port->serial->type->ioctl)
retval = port->serial->type->ioctl(tty, cmd, arg);
- else
- retval = -ENOIOCTLCMD;
}
return retval;
.unthrottle = serial_unthrottle,
.break_ctl = serial_break,
.chars_in_buffer = serial_chars_in_buffer,
+ .wait_until_sent = serial_wait_until_sent,
.tiocmget = serial_tiocmget,
.tiocmset = serial_tiocmset,
.get_icount = serial_get_icount,
set_to_generic_if_null(device, close);
set_to_generic_if_null(device, write_room);
set_to_generic_if_null(device, chars_in_buffer);
+ if (device->tx_empty)
+ set_to_generic_if_null(device, wait_until_sent);
set_to_generic_if_null(device, read_bulk_callback);
set_to_generic_if_null(device, write_bulk_callback);
set_to_generic_if_null(device, process_read_urb);
*/
#define COPY_PORT(dest, src) \
do { \
+ int i; \
+ \
+ for (i = 0; i < ARRAY_SIZE(src->read_urbs); ++i) { \
+ dest->read_urbs[i] = src->read_urbs[i]; \
+ dest->read_urbs[i]->context = dest; \
+ dest->bulk_in_buffers[i] = src->bulk_in_buffers[i]; \
+ } \
dest->read_urb = src->read_urb; \
dest->bulk_in_endpointAddress = src->bulk_in_endpointAddress;\
dest->bulk_in_buffer = src->bulk_in_buffer; \
+ dest->bulk_in_size = src->bulk_in_size; \
dest->interrupt_in_urb = src->interrupt_in_urb; \
+ dest->interrupt_in_urb->context = dest; \
dest->interrupt_in_endpointAddress = \
src->interrupt_in_endpointAddress;\
dest->interrupt_in_buffer = src->interrupt_in_buffer; \
struct whiteheat_port_settings port_settings;
unsigned int cflag = tty->termios.c_cflag;
- port_settings.port = port->number + 1;
+ port_settings.port = port->number - port->serial->minor + 1;
/* get the byte size */
switch (cflag & CSIZE) {
int len;
unsigned char *buf;
- if (port->number != 0)
- return -ENODEV;
-
buf = kmalloc(MAX_SETUP_DATA_SIZE, GFP_KERNEL);
if (!buf)
return -ENOMEM;
result = usb_control_msg(udev, usb_sndctrlpipe(udev, 0),
0x22, 0x21,
0x0001, 0x0000, NULL, len,
- HZ * USB_CTRL_GET_TIMEOUT);
+ USB_CTRL_GET_TIMEOUT);
dev_dbg(dev, "result = %d\n", result);
/* send 2st cmd and recieve data */
result = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0),
0x21, 0xa1,
0x0000, 0x0000, buf, len,
- HZ * USB_CTRL_GET_TIMEOUT);
+ USB_CTRL_GET_TIMEOUT);
debug_data(dev, __func__, len, buf, result);
/* send 3 cmd */
result = usb_control_msg(udev, usb_sndctrlpipe(udev, 0),
0x20, 0x21,
0x0000, 0x0000, buf, len,
- HZ * USB_CTRL_GET_TIMEOUT);
+ USB_CTRL_GET_TIMEOUT);
debug_data(dev, __func__, len, buf, result);
/* send 4 cmd */
result = usb_control_msg(udev, usb_sndctrlpipe(udev, 0),
0x22, 0x21,
0x0003, 0x0000, NULL, len,
- HZ * USB_CTRL_GET_TIMEOUT);
+ USB_CTRL_GET_TIMEOUT);
dev_dbg(dev, "result = %d\n", result);
/* send 5 cmd */
result = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0),
0x21, 0xa1,
0x0000, 0x0000, buf, len,
- HZ * USB_CTRL_GET_TIMEOUT);
+ USB_CTRL_GET_TIMEOUT);
debug_data(dev, __func__, len, buf, result);
/* send 6 cmd */
result = usb_control_msg(udev, usb_sndctrlpipe(udev, 0),
0x20, 0x21,
0x0000, 0x0000, buf, len,
- HZ * USB_CTRL_GET_TIMEOUT);
+ USB_CTRL_GET_TIMEOUT);
debug_data(dev, __func__, len, buf, result);
kfree(buf);
int len;
unsigned char *buf;
- if (port->number != 0)
- return;
-
buf = kmalloc(MAX_SETUP_DATA_SIZE, GFP_KERNEL);
if (!buf)
return;
result = usb_control_msg(udev, usb_sndctrlpipe(udev, 0),
0x22, 0x21,
0x0002, 0x0000, NULL, len,
- HZ * USB_CTRL_GET_TIMEOUT);
+ USB_CTRL_GET_TIMEOUT);
dev_dbg(dev, "result = %d\n", result);
/* send 2st ctl cmd(CTL 21 22 03 00 00 00 00 00 ) */
result = usb_control_msg(udev, usb_sndctrlpipe(udev, 0),
0x22, 0x21,
0x0003, 0x0000, NULL, len,
- HZ * USB_CTRL_GET_TIMEOUT);
+ USB_CTRL_GET_TIMEOUT);
dev_dbg(dev, "result = %d\n", result);
/* send 3st cmd and recieve data */
result = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0),
0x21, 0xa1,
0x0000, 0x0000, buf, len,
- HZ * USB_CTRL_GET_TIMEOUT);
+ USB_CTRL_GET_TIMEOUT);
debug_data(dev, __func__, len, buf, result);
/* send 4 cmd */
result = usb_control_msg(udev, usb_sndctrlpipe(udev, 0),
0x20, 0x21,
0x0000, 0x0000, buf, len,
- HZ * USB_CTRL_GET_TIMEOUT);
+ USB_CTRL_GET_TIMEOUT);
debug_data(dev, __func__, len, buf, result);
/* send 5 cmd */
result = usb_control_msg(udev, usb_sndctrlpipe(udev, 0),
0x22, 0x21,
0x0003, 0x0000, NULL, len,
- HZ * USB_CTRL_GET_TIMEOUT);
+ USB_CTRL_GET_TIMEOUT);
dev_dbg(dev, "result = %d\n", result);
/* send 6 cmd */
result = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0),
0x21, 0xa1,
0x0000, 0x0000, buf, len,
- HZ * USB_CTRL_GET_TIMEOUT);
+ USB_CTRL_GET_TIMEOUT);
debug_data(dev, __func__, len, buf, result);
/* send 7 cmd */
result = usb_control_msg(udev, usb_sndctrlpipe(udev, 0),
0x20, 0x21,
0x0000, 0x0000, buf, len,
- HZ * USB_CTRL_GET_TIMEOUT);
+ USB_CTRL_GET_TIMEOUT);
debug_data(dev, __func__, len, buf, result);
/* send 8 cmd */
result = usb_control_msg(udev, usb_sndctrlpipe(udev, 0),
0x22, 0x21,
0x0003, 0x0000, NULL, len,
- HZ * USB_CTRL_GET_TIMEOUT);
+ USB_CTRL_GET_TIMEOUT);
dev_dbg(dev, "result = %d\n", result);
kfree(buf);
}
static const struct usb_device_id id_table[] = {
- { USB_DEVICE(0x19d2, 0xffff) }, /* AC8700 */
- { USB_DEVICE(0x19d2, 0xfffe) },
- { USB_DEVICE(0x19d2, 0xfffd) }, /* MG880 */
+ /* AC8710, AC8710T */
+ { USB_DEVICE_AND_INTERFACE_INFO(0x19d2, 0xffff, 0xff, 0xff, 0xff) },
+ /* AC8700 */
+ { USB_DEVICE_AND_INTERFACE_INFO(0x19d2, 0xfffe, 0xff, 0xff, 0xff) },
+ /* MG880 */
+ { USB_DEVICE(0x19d2, 0xfffd) },
+ { USB_DEVICE(0x19d2, 0xfffc) },
+ { USB_DEVICE(0x19d2, 0xfffb) },
+ /* AC2726, AC8710_V3 */
+ { USB_DEVICE_AND_INTERFACE_INFO(0x19d2, 0xfff1, 0xff, 0xff, 0xff) },
+ { USB_DEVICE(0x19d2, 0xfff6) },
+ { USB_DEVICE(0x19d2, 0xfff7) },
+ { USB_DEVICE(0x19d2, 0xfff8) },
+ { USB_DEVICE(0x19d2, 0xfff9) },
+ { USB_DEVICE(0x19d2, 0xffee) },
+ /* AC2716, MC2716 */
+ { USB_DEVICE_AND_INTERFACE_INFO(0x19d2, 0xffed, 0xff, 0xff, 0xff) },
+ /* AD3812 */
+ { USB_DEVICE_AND_INTERFACE_INFO(0x19d2, 0xffeb, 0xff, 0xff, 0xff) },
+ { USB_DEVICE(0x19d2, 0xffec) },
{ USB_DEVICE(0x05C6, 0x3197) },
{ USB_DEVICE(0x05C6, 0x6000) },
+ { USB_DEVICE(0x05C6, 0x9008) },
{ },
};
MODULE_DEVICE_TABLE(usb, id_table);
int status_len;
u32 flag;
-#ifdef CONFIG_REALTEK_AUTOPM
struct us_data *us;
+
+#ifdef CONFIG_REALTEK_AUTOPM
struct timer_list rts51x_suspend_timer;
unsigned long timer_expires;
int pwr_state;
us->extra = chip;
us->extra_destructor = realtek_cr_destructor;
us->max_lun = chip->max_lun = rts51x_get_max_lun(us);
+ chip->us = us;
usb_stor_dbg(us, "chip->max_lun = %d\n", chip->max_lun);
SET_AUTO_DELINK(chip);
}
#ifdef CONFIG_REALTEK_AUTOPM
- if (ss_en) {
- chip->us = us;
+ if (ss_en)
realtek_cr_autosuspend_setup(us);
- }
#endif
usb_stor_dbg(us, "chip->flag = 0x%x\n", chip->flag);
*/
static char *vfio_devnode(struct device *dev, umode_t *mode)
{
- if (MINOR(dev->devt) == 0)
+ if (mode && (MINOR(dev->devt) == 0))
*mode = S_IRUGO | S_IWUGO;
return kasprintf(GFP_KERNEL, "vfio/%s", dev_name(dev));
config FB_GOLDFISH
tristate "Goldfish Framebuffer"
- depends on FB
+ depends on FB && HAS_DMA
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
help
This framebuffer driver supports Microsoft Hyper-V Synthetic Video.
+config FB_SIMPLE
+ bool "Simple framebuffer support"
+ depends on (FB = y) && OF
+ select FB_CFB_FILLRECT
+ select FB_CFB_COPYAREA
+ select FB_CFB_IMAGEBLIT
+ help
+ Say Y if you want support for a simple frame-buffer.
+
+ This driver assumes that the display hardware has been initialized
+ before the kernel boots, and the kernel will simply render to the
+ pre-allocated frame buffer surface.
+
+ Configuration re: surface address, size, and format must be provided
+ through device tree, or potentially plain old platform data in the
+ future.
+
source "drivers/video/omap/Kconfig"
source "drivers/video/omap2/Kconfig"
source "drivers/video/exynos/Kconfig"
obj-$(CONFIG_FB_DA8XX) += da8xx-fb.o
obj-$(CONFIG_FB_MXS) += mxsfb.o
obj-$(CONFIG_FB_SSD1307) += ssd1307fb.o
+obj-$(CONFIG_FB_SIMPLE) += simplefb.o
# the test framebuffer is last
obj-$(CONFIG_FB_VIRTUAL) += vfb.o
static void exit_backlight(struct atmel_lcdfb_info *sinfo)
{
- if (sinfo->backlight)
- backlight_device_unregister(sinfo->backlight);
+ if (!sinfo->backlight)
+ return;
+
+ if (sinfo->backlight->ops) {
+ sinfo->backlight->props.power = FB_BLANK_POWERDOWN;
+ sinfo->backlight->ops->update_status(sinfo->backlight);
+ }
+ backlight_device_unregister(sinfo->backlight);
}
#else
if (info->fix.smem_len) {
unsigned int smem_len = (var->xres_virtual * var->yres_virtual
* ((var->bits_per_pixel + 7) / 8));
- if (smem_len > info->fix.smem_len)
+ if (smem_len > info->fix.smem_len) {
+ dev_err(dev, "Frame buffer is too small (%u) for screen size (need at least %u)\n",
+ info->fix.smem_len, smem_len);
return -EINVAL;
+ }
}
/* Saturate vertical and horizontal timings at maximum values */
font-objs += $(font-objs-y)
+obj-$(CONFIG_FONTS) += font.o
+
# Each configuration option enables a list of files.
obj-$(CONFIG_DUMMY_CONSOLE) += dummycon.o
module_param_named(def_disp, def_disp_name, charp, 0);
MODULE_PARM_DESC(def_disp, "default display name");
+static bool dss_initialized;
+
const char *omapdss_get_default_display_name(void)
{
return core.default_display_name;
}
EXPORT_SYMBOL(omapdss_get_version);
+bool omapdss_is_initialized(void)
+{
+ return dss_initialized;
+}
+EXPORT_SYMBOL(omapdss_is_initialized);
+
struct platform_device *dss_get_core_pdev(void)
{
return core.pdev;
return r;
}
+ dss_initialized = true;
+
return 0;
}
static int __init omap_dss_init2(void)
{
- return omap_dss_register_drivers();
+ int r;
+
+ r = omap_dss_register_drivers();
+ if (r)
+ return r;
+
+ dss_initialized = true;
+
+ return 0;
}
core_initcall(omap_dss_init);
DBG("omapfb_probe\n");
+ if (omapdss_is_initialized() == false)
+ return -EPROBE_DEFER;
+
if (pdev->num_resources != 0) {
dev_err(&pdev->dev, "probed for an unknown device\n");
r = -ENODEV;
r = vm_iomap_memory(vma, info->fix.smem_start, info->fix.smem_len);
dev_dbg(info->device, "ps3fb: mmap framebuffer P(%lx)->V(%lx)\n",
- info->fix.smem_start + vma->vm_pgoff << PAGE_SHIFT,
+ info->fix.smem_start + (vma->vm_pgoff << PAGE_SHIFT),
vma->vm_start);
return r;
--- /dev/null
+/*
+ * Simplest possible simple frame-buffer driver, as a platform device
+ *
+ * Copyright (c) 2013, Stephen Warren
+ *
+ * Based on q40fb.c, which was:
+ * Copyright (C) 2001 Richard Zidlicky <rz@linux-m68k.org>
+ *
+ * Also based on offb.c, which was:
+ * Copyright (C) 1997 Geert Uytterhoeven
+ * Copyright (C) 1996 Paul Mackerras
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ */
+
+#include <linux/errno.h>
+#include <linux/fb.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+
+static struct fb_fix_screeninfo simplefb_fix = {
+ .id = "simple",
+ .type = FB_TYPE_PACKED_PIXELS,
+ .visual = FB_VISUAL_TRUECOLOR,
+ .accel = FB_ACCEL_NONE,
+};
+
+static struct fb_var_screeninfo simplefb_var = {
+ .height = -1,
+ .width = -1,
+ .activate = FB_ACTIVATE_NOW,
+ .vmode = FB_VMODE_NONINTERLACED,
+};
+
+static int simplefb_setcolreg(u_int regno, u_int red, u_int green, u_int blue,
+ u_int transp, struct fb_info *info)
+{
+ u32 *pal = info->pseudo_palette;
+ u32 cr = red >> (16 - info->var.red.length);
+ u32 cg = green >> (16 - info->var.green.length);
+ u32 cb = blue >> (16 - info->var.blue.length);
+ u32 value;
+
+ if (regno >= 16)
+ return -EINVAL;
+
+ value = (cr << info->var.red.offset) |
+ (cg << info->var.green.offset) |
+ (cb << info->var.blue.offset);
+ if (info->var.transp.length > 0) {
+ u32 mask = (1 << info->var.transp.length) - 1;
+ mask <<= info->var.transp.offset;
+ value |= mask;
+ }
+ pal[regno] = value;
+
+ return 0;
+}
+
+static struct fb_ops simplefb_ops = {
+ .owner = THIS_MODULE,
+ .fb_setcolreg = simplefb_setcolreg,
+ .fb_fillrect = cfb_fillrect,
+ .fb_copyarea = cfb_copyarea,
+ .fb_imageblit = cfb_imageblit,
+};
+
+struct simplefb_format {
+ const char *name;
+ u32 bits_per_pixel;
+ struct fb_bitfield red;
+ struct fb_bitfield green;
+ struct fb_bitfield blue;
+ struct fb_bitfield transp;
+};
+
+static struct simplefb_format simplefb_formats[] = {
+ { "r5g6b5", 16, {11, 5}, {5, 6}, {0, 5}, {0, 0} },
+};
+
+struct simplefb_params {
+ u32 width;
+ u32 height;
+ u32 stride;
+ struct simplefb_format *format;
+};
+
+static int simplefb_parse_dt(struct platform_device *pdev,
+ struct simplefb_params *params)
+{
+ struct device_node *np = pdev->dev.of_node;
+ int ret;
+ const char *format;
+ int i;
+
+ ret = of_property_read_u32(np, "width", ¶ms->width);
+ if (ret) {
+ dev_err(&pdev->dev, "Can't parse width property\n");
+ return ret;
+ }
+
+ ret = of_property_read_u32(np, "height", ¶ms->height);
+ if (ret) {
+ dev_err(&pdev->dev, "Can't parse height property\n");
+ return ret;
+ }
+
+ ret = of_property_read_u32(np, "stride", ¶ms->stride);
+ if (ret) {
+ dev_err(&pdev->dev, "Can't parse stride property\n");
+ return ret;
+ }
+
+ ret = of_property_read_string(np, "format", &format);
+ if (ret) {
+ dev_err(&pdev->dev, "Can't parse format property\n");
+ return ret;
+ }
+ params->format = NULL;
+ for (i = 0; i < ARRAY_SIZE(simplefb_formats); i++) {
+ if (strcmp(format, simplefb_formats[i].name))
+ continue;
+ params->format = &simplefb_formats[i];
+ break;
+ }
+ if (!params->format) {
+ dev_err(&pdev->dev, "Invalid format value\n");
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static int simplefb_probe(struct platform_device *pdev)
+{
+ int ret;
+ struct simplefb_params params;
+ struct fb_info *info;
+ struct resource *mem;
+
+ if (fb_get_options("simplefb", NULL))
+ return -ENODEV;
+
+ ret = simplefb_parse_dt(pdev, ¶ms);
+ if (ret)
+ return ret;
+
+ mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!mem) {
+ dev_err(&pdev->dev, "No memory resource\n");
+ return -EINVAL;
+ }
+
+ info = framebuffer_alloc(sizeof(u32) * 16, &pdev->dev);
+ if (!info)
+ return -ENOMEM;
+ platform_set_drvdata(pdev, info);
+
+ info->fix = simplefb_fix;
+ info->fix.smem_start = mem->start;
+ info->fix.smem_len = resource_size(mem);
+ info->fix.line_length = params.stride;
+
+ info->var = simplefb_var;
+ info->var.xres = params.width;
+ info->var.yres = params.height;
+ info->var.xres_virtual = params.width;
+ info->var.yres_virtual = params.height;
+ info->var.bits_per_pixel = params.format->bits_per_pixel;
+ info->var.red = params.format->red;
+ info->var.green = params.format->green;
+ info->var.blue = params.format->blue;
+ info->var.transp = params.format->transp;
+
+ info->fbops = &simplefb_ops;
+ info->flags = FBINFO_DEFAULT;
+ info->screen_base = devm_ioremap(&pdev->dev, info->fix.smem_start,
+ info->fix.smem_len);
+ if (!info->screen_base) {
+ framebuffer_release(info);
+ return -ENODEV;
+ }
+ info->pseudo_palette = (void *)(info + 1);
+
+ ret = register_framebuffer(info);
+ if (ret < 0) {
+ dev_err(&pdev->dev, "Unable to register simplefb: %d\n", ret);
+ framebuffer_release(info);
+ return ret;
+ }
+
+ dev_info(&pdev->dev, "fb%d: simplefb registered!\n", info->node);
+
+ return 0;
+}
+
+static int simplefb_remove(struct platform_device *pdev)
+{
+ struct fb_info *info = platform_get_drvdata(pdev);
+
+ unregister_framebuffer(info);
+ framebuffer_release(info);
+
+ return 0;
+}
+
+static const struct of_device_id simplefb_of_match[] = {
+ { .compatible = "simple-framebuffer", },
+ { },
+};
+MODULE_DEVICE_TABLE(of, simplefb_of_match);
+
+static struct platform_driver simplefb_driver = {
+ .driver = {
+ .name = "simple-framebuffer",
+ .owner = THIS_MODULE,
+ .of_match_table = simplefb_of_match,
+ },
+ .probe = simplefb_probe,
+ .remove = simplefb_remove,
+};
+module_platform_driver(simplefb_driver);
+
+MODULE_AUTHOR("Stephen Warren <swarren@wwwdotorg.org>");
+MODULE_DESCRIPTION("Simple framebuffer driver");
+MODULE_LICENSE("GPL v2");
#ifdef CONFIG_FRONTSWAP
static bool frontswap __read_mostly = true;
module_param(frontswap, bool, S_IRUGO);
+#else /* CONFIG_FRONTSWAP */
+#define frontswap (0)
#endif /* CONFIG_FRONTSWAP */
#ifdef CONFIG_XEN_SELFBALLOONING
else
pci_restore_state(dev);
- if (pci_find_capability(dev, PCI_CAP_ID_MSIX)) {
+ if (dev->msix_cap) {
struct physdev_pci_device ppdev = {
.seg = pci_domain_nr(dev->bus),
.bus = dev->bus->number,
if (err)
goto config_release;
- if (pci_find_capability(dev, PCI_CAP_ID_MSIX)) {
+ if (dev->msix_cap) {
struct physdev_pci_device ppdev = {
.seg = pci_domain_nr(dev->bus),
.bus = dev->bus->number,
err = xenbus_map_ring(dev, gnt_ref, &node->handle, addr);
if (err)
- goto out_err;
+ goto out_err_free_ballooned_pages;
spin_lock(&xenbus_valloc_lock);
list_add(&node->next, &xenbus_valloc_pages);
*vaddr = addr;
return 0;
- out_err:
+ out_err_free_ballooned_pages:
free_xenballooned_pages(1, &node->page);
+ out_err:
kfree(node);
return err;
}
int xs_input_avail(void);
extern struct xenstore_domain_interface *xen_store_interface;
extern int xen_store_evtchn;
+extern enum xenstore_init xen_store_domain_type;
extern const struct file_operations xen_xenbus_fops;
struct xenstore_domain_interface *xen_store_interface;
EXPORT_SYMBOL_GPL(xen_store_interface);
+enum xenstore_init xen_store_domain_type;
+EXPORT_SYMBOL_GPL(xen_store_domain_type);
+
static unsigned long xen_store_mfn;
static BLOCKING_NOTIFIER_HEAD(xenstore_chain);
return err;
}
-enum xenstore_init {
- UNKNOWN,
- PV,
- HVM,
- LOCAL,
-};
static int __init xenbus_init(void)
{
int err = 0;
- enum xenstore_init usage = UNKNOWN;
uint64_t v = 0;
+ xen_store_domain_type = XS_UNKNOWN;
if (!xen_domain())
return -ENODEV;
xenbus_ring_ops_init();
if (xen_pv_domain())
- usage = PV;
+ xen_store_domain_type = XS_PV;
if (xen_hvm_domain())
- usage = HVM;
+ xen_store_domain_type = XS_HVM;
if (xen_hvm_domain() && xen_initial_domain())
- usage = LOCAL;
+ xen_store_domain_type = XS_LOCAL;
if (xen_pv_domain() && !xen_start_info->store_evtchn)
- usage = LOCAL;
+ xen_store_domain_type = XS_LOCAL;
if (xen_pv_domain() && xen_start_info->store_evtchn)
xenstored_ready = 1;
- switch (usage) {
- case LOCAL:
+ switch (xen_store_domain_type) {
+ case XS_LOCAL:
err = xenstored_local_init();
if (err)
goto out_error;
xen_store_interface = mfn_to_virt(xen_store_mfn);
break;
- case PV:
+ case XS_PV:
xen_store_evtchn = xen_start_info->store_evtchn;
xen_store_mfn = xen_start_info->store_mfn;
xen_store_interface = mfn_to_virt(xen_store_mfn);
break;
- case HVM:
+ case XS_HVM:
err = hvm_get_parameter(HVM_PARAM_STORE_EVTCHN, &v);
if (err)
goto out_error;
struct bus_type bus;
};
+enum xenstore_init {
+ XS_UNKNOWN,
+ XS_PV,
+ XS_HVM,
+ XS_LOCAL,
+};
+
extern struct device_attribute xenbus_dev_attrs[];
extern int xenbus_match(struct device *_dev, struct device_driver *_drv);
#include "xenbus_probe.h"
+static struct workqueue_struct *xenbus_frontend_wq;
+
/* device/<type>/<id> => <type>-<id> */
static int frontend_bus_id(char bus_id[XEN_BUS_ID_SIZE], const char *nodename)
{
xenbus_otherend_changed(watch, vec, len, 1);
}
+static void xenbus_frontend_delayed_resume(struct work_struct *w)
+{
+ struct xenbus_device *xdev = container_of(w, struct xenbus_device, work);
+
+ xenbus_dev_resume(&xdev->dev);
+}
+
+static int xenbus_frontend_dev_resume(struct device *dev)
+{
+ /*
+ * If xenstored is running in this domain, we cannot access the backend
+ * state at the moment, so we need to defer xenbus_dev_resume
+ */
+ if (xen_store_domain_type == XS_LOCAL) {
+ struct xenbus_device *xdev = to_xenbus_device(dev);
+
+ if (!xenbus_frontend_wq) {
+ pr_err("%s: no workqueue to process delayed resume\n",
+ xdev->nodename);
+ return -EFAULT;
+ }
+
+ INIT_WORK(&xdev->work, xenbus_frontend_delayed_resume);
+ queue_work(xenbus_frontend_wq, &xdev->work);
+
+ return 0;
+ }
+
+ return xenbus_dev_resume(dev);
+}
+
static const struct dev_pm_ops xenbus_pm_ops = {
.suspend = xenbus_dev_suspend,
- .resume = xenbus_dev_resume,
+ .resume = xenbus_frontend_dev_resume,
.freeze = xenbus_dev_suspend,
.thaw = xenbus_dev_cancel,
.restore = xenbus_dev_resume,
register_xenstore_notifier(&xenstore_notifier);
+ xenbus_frontend_wq = create_workqueue("xenbus_frontend");
+
return 0;
}
subsys_initcall(xenbus_probe_frontend_init);
kunmap_atomic(ring);
while (atomic_read(&ctx->reqs_active) > 0) {
- wait_event(ctx->wait, head != ctx->tail);
+ wait_event(ctx->wait,
+ head != ctx->tail ||
+ atomic_read(&ctx->reqs_active) <= 0);
avail = (head <= ctx->tail ? ctx->tail : ctx->nr_events) - head;
* < min_nr if the timeout specified by timeout has elapsed
* before sufficient events are available, where timeout == NULL
* specifies an infinite timeout. Note that the timeout pointed to by
- * timeout is relative and will be updated if not NULL and the
- * operation blocks. Will fail with -ENOSYS if not implemented.
+ * timeout is relative. Will fail with -ENOSYS if not implemented.
*/
SYSCALL_DEFINE5(io_getevents, aio_context_t, ctx_id,
long, min_nr,
result = filldir(dirent, keybuf, keysize, filp->f_pos,
(ino_t) value, d_type);
}
-
- filp->f_pos++;
+ if (!result)
+ filp->f_pos++;
befs_debug(sb, "<--- befs_readdir() filp->f_pos %Ld", filp->f_pos);
#include <linux/slab.h>
#include <linux/vfs.h>
#include <linux/fs.h>
+#include <linux/inet.h>
#include "cifsglob.h"
#include "cifsproto.h"
#include "cifsfs.h"
}
/**
- * cifs_get_share_name - extracts share name from UNC
- * @node_name: pointer to UNC string
+ * cifs_build_devname - build a devicename from a UNC and optional prepath
+ * @nodename: pointer to UNC string
+ * @prepath: pointer to prefixpath (or NULL if there isn't one)
*
- * Extracts sharename form full UNC.
- * i.e. strips from UNC trailing path that is not part of share
- * name and fixup missing '\' in the beginning of DFS node refferal
- * if necessary.
- * Returns pointer to share name on success or ERR_PTR on error.
- * Caller is responsible for freeing returned string.
+ * Build a new cifs devicename after chasing a DFS referral. Allocate a buffer
+ * big enough to hold the final thing. Copy the UNC from the nodename, and
+ * concatenate the prepath onto the end of it if there is one.
+ *
+ * Returns pointer to the built string, or a ERR_PTR. Caller is responsible
+ * for freeing the returned string.
*/
-static char *cifs_get_share_name(const char *node_name)
+static char *
+cifs_build_devname(char *nodename, const char *prepath)
{
- int len;
- char *UNC;
- char *pSep;
-
- len = strlen(node_name);
- UNC = kmalloc(len+2 /*for term null and additional \ if it's missed */,
- GFP_KERNEL);
- if (!UNC)
- return ERR_PTR(-ENOMEM);
+ size_t pplen;
+ size_t unclen;
+ char *dev;
+ char *pos;
+
+ /* skip over any preceding delimiters */
+ nodename += strspn(nodename, "\\");
+ if (!*nodename)
+ return ERR_PTR(-EINVAL);
- /* get share name and server name */
- if (node_name[1] != '\\') {
- UNC[0] = '\\';
- strncpy(UNC+1, node_name, len);
- len++;
- UNC[len] = 0;
- } else {
- strncpy(UNC, node_name, len);
- UNC[len] = 0;
- }
+ /* get length of UNC and set pos to last char */
+ unclen = strlen(nodename);
+ pos = nodename + unclen - 1;
- /* find server name end */
- pSep = memchr(UNC+2, '\\', len-2);
- if (!pSep) {
- cifs_dbg(VFS, "%s: no server name end in node name: %s\n",
- __func__, node_name);
- kfree(UNC);
- return ERR_PTR(-EINVAL);
+ /* trim off any trailing delimiters */
+ while (*pos == '\\') {
+ --pos;
+ --unclen;
}
- /* find sharename end */
- pSep++;
- pSep = memchr(UNC+(pSep-UNC), '\\', len-(pSep-UNC));
- if (pSep) {
- /* trim path up to sharename end
- * now we have share name in UNC */
- *pSep = 0;
+ /* allocate a buffer:
+ * +2 for preceding "//"
+ * +1 for delimiter between UNC and prepath
+ * +1 for trailing NULL
+ */
+ pplen = prepath ? strlen(prepath) : 0;
+ dev = kmalloc(2 + unclen + 1 + pplen + 1, GFP_KERNEL);
+ if (!dev)
+ return ERR_PTR(-ENOMEM);
+
+ pos = dev;
+ /* add the initial "//" */
+ *pos = '/';
+ ++pos;
+ *pos = '/';
+ ++pos;
+
+ /* copy in the UNC portion from referral */
+ memcpy(pos, nodename, unclen);
+ pos += unclen;
+
+ /* copy the prefixpath remainder (if there is one) */
+ if (pplen) {
+ *pos = '/';
+ ++pos;
+ memcpy(pos, prepath, pplen);
+ pos += pplen;
}
- return UNC;
+ /* NULL terminator */
+ *pos = '\0';
+
+ convert_delimiter(dev, '/');
+ return dev;
}
{
int rc;
char *mountdata = NULL;
+ const char *prepath = NULL;
int md_len;
char *tkn_e;
char *srvIP = NULL;
if (sb_mountdata == NULL)
return ERR_PTR(-EINVAL);
- *devname = cifs_get_share_name(ref->node_name);
+ if (strlen(fullpath) - ref->path_consumed)
+ prepath = fullpath + ref->path_consumed;
+
+ *devname = cifs_build_devname(ref->node_name, prepath);
if (IS_ERR(*devname)) {
rc = PTR_ERR(*devname);
*devname = NULL;
goto compose_mount_options_err;
}
- /* md_len = strlen(...) + 12 for 'sep+prefixpath='
- * assuming that we have 'unc=' and 'ip=' in
- * the original sb_mountdata
+ /*
+ * In most cases, we'll be building a shorter string than the original,
+ * but we do have to assume that the address in the ip= option may be
+ * much longer than the original. Add the max length of an address
+ * string to the length of the original string to allow for worst case.
*/
- md_len = strlen(sb_mountdata) + rc + strlen(ref->node_name) + 12;
- mountdata = kzalloc(md_len+1, GFP_KERNEL);
+ md_len = strlen(sb_mountdata) + INET6_ADDRSTRLEN;
+ mountdata = kzalloc(md_len + 1, GFP_KERNEL);
if (mountdata == NULL) {
rc = -ENOMEM;
goto compose_mount_options_err;
strncat(mountdata, &sep, 1);
strcat(mountdata, "ip=");
strcat(mountdata, srvIP);
- strncat(mountdata, &sep, 1);
- strcat(mountdata, "unc=");
- strcat(mountdata, *devname);
-
- /* find & copy prefixpath */
- tkn_e = strchr(ref->node_name + 2, '\\');
- if (tkn_e == NULL) {
- /* invalid unc, missing share name*/
- rc = -EINVAL;
- goto compose_mount_options_err;
- }
-
- tkn_e = strchr(tkn_e + 1, '\\');
- if (tkn_e || (strlen(fullpath) - ref->path_consumed)) {
- strncat(mountdata, &sep, 1);
- strcat(mountdata, "prefixpath=");
- if (tkn_e)
- strcat(mountdata, tkn_e + 1);
- strcat(mountdata, fullpath + ref->path_consumed);
- }
/*cifs_dbg(FYI, "%s: parent mountdata: %s\n", __func__, sb_mountdata);*/
/*cifs_dbg(FYI, "%s: submount mountdata: %s\n", __func__, mountdata );*/
cifs_show_security(s, tcon->ses->server);
cifs_show_cache_flavor(s, cifs_sb);
- seq_printf(s, ",unc=");
- seq_escape(s, tcon->treeName, " \t\n\\");
-
if (cifs_sb->mnt_cifs_flags & CIFS_MOUNT_MULTIUSER)
seq_printf(s, ",multiuser");
else if (tcon->ses->user_name)
#endif
case Opt_sec_none:
vol->nullauth = 1;
+ vol->secFlg |= CIFSSEC_MAY_NTLM;
break;
default:
cifs_dbg(VFS, "bad security option: %s\n", value);
vol->backupuid_specified = false; /* no backup intent for a user */
vol->backupgid_specified = false; /* no backup intent for a group */
- /*
- * For now, we ignore -EINVAL errors under the assumption that the
- * unc= and prefixpath= options will be usable.
- */
- if (cifs_parse_devname(devname, vol) == -ENOMEM) {
- printk(KERN_ERR "CIFS: Unable to allocate memory to parse "
- "device string.\n");
- goto out_nomem;
+ switch (cifs_parse_devname(devname, vol)) {
+ case 0:
+ break;
+ case -ENOMEM:
+ cifs_dbg(VFS, "Unable to allocate memory for devname.\n");
+ goto cifs_parse_mount_err;
+ case -EINVAL:
+ cifs_dbg(VFS, "Malformed UNC in devname.\n");
+ goto cifs_parse_mount_err;
+ default:
+ cifs_dbg(VFS, "Unknown error parsing devname.\n");
+ goto cifs_parse_mount_err;
}
while ((data = strsep(&options, separator)) != NULL) {
}
#endif
if (!vol->UNC) {
- cifs_dbg(VFS, "CIFS mount error: No usable UNC path provided in device string or in unc= option!\n");
+ cifs_dbg(VFS, "CIFS mount error: No usable UNC path provided in device string!\n");
goto cifs_parse_mount_err;
}
pos = full_path + unc_len;
if (pplen) {
- *pos++ = CIFS_DIR_SEP(cifs_sb);
- strncpy(pos, vol->prepath, pplen);
+ *pos = CIFS_DIR_SEP(cifs_sb);
+ strncpy(pos + 1, vol->prepath, pplen);
pos += pplen;
}
/**
* dns_resolve_server_name_to_ip - Resolve UNC server name to ip address.
- * @unc: UNC path specifying the server
+ * @unc: UNC path specifying the server (with '/' as delimiter)
* @ip_addr: Where to return the IP address.
*
* The IP address will be returned in string form, and the caller is
hostname = unc + 2;
/* Search for server name delimiter */
- sep = memchr(hostname, '\\', len);
+ sep = memchr(hostname, '/', len);
if (sep)
len = sep - hostname;
else
if (fattr->cf_flags & CIFS_FATTR_DFS_REFERRAL)
inode->i_flags |= S_AUTOMOUNT;
- cifs_set_ops(inode);
+ if (inode->i_state & I_NEW)
+ cifs_set_ops(inode);
}
void
static int
ecryptfs_fsync(struct file *file, loff_t start, loff_t end, int datasync)
{
+ int rc;
+
+ rc = filemap_write_and_wait(file->f_mapping);
+ if (rc)
+ return rc;
+
return vfs_fsync(ecryptfs_file_to_lower(file), datasync);
}
bytes = efivar_entry_set_get_size(var, attributes, &datasize,
data, &set);
- if (!set && bytes)
+ if (!set && bytes) {
+ if (bytes == -ENOENT)
+ bytes = -EIO;
goto out;
+ }
if (bytes == -ENOENT) {
drop_nlink(inode);
int err;
err = efivar_entry_size(var, &datasize);
- if (err)
+
+ /*
+ * efivarfs represents uncommitted variables with
+ * zero-length files. Reading them should return EOF.
+ */
+ if (err == -ENOENT)
+ return 0;
+ else if (err)
return err;
data = kmalloc(datasize + sizeof(attributes), GFP_KERNEL);
return 0;
}
+static unsigned long calc_fat_clusters(struct super_block *sb)
+{
+ struct msdos_sb_info *sbi = MSDOS_SB(sb);
+
+ /* Divide first to avoid overflow */
+ if (sbi->fat_bits != 12) {
+ unsigned long ent_per_sec = sb->s_blocksize * 8 / sbi->fat_bits;
+ return ent_per_sec * sbi->fat_length;
+ }
+
+ return sbi->fat_length * sb->s_blocksize * 8 / sbi->fat_bits;
+}
+
/*
* Read the super block of an MS-DOS FS.
*/
sbi->dirty = b->fat16.state & FAT_STATE_DIRTY;
/* check that FAT table does not overflow */
- fat_clusters = sbi->fat_length * sb->s_blocksize * 8 / sbi->fat_bits;
+ fat_clusters = calc_fat_clusters(sb);
total_clusters = min(total_clusters, fat_clusters - FAT_START_ENT);
if (total_clusters > MAX_FAT(sb)) {
if (!silent)
static int fuse_dentry_revalidate(struct dentry *entry, unsigned int flags)
{
struct inode *inode;
+ struct dentry *parent;
+ struct fuse_conn *fc;
inode = ACCESS_ONCE(entry->d_inode);
if (inode && is_bad_inode(inode))
else if (fuse_dentry_time(entry) < get_jiffies_64()) {
int err;
struct fuse_entry_out outarg;
- struct fuse_conn *fc;
struct fuse_req *req;
struct fuse_forget_link *forget;
- struct dentry *parent;
u64 attr_version;
/* For negative dentries, always do a fresh lookup */
entry_attr_timeout(&outarg),
attr_version);
fuse_change_entry_timeout(entry, &outarg);
+ } else if (inode) {
+ fc = get_fuse_conn(inode);
+ if (fc->readdirplus_auto) {
+ parent = dget_parent(entry);
+ fuse_advise_use_readdirplus(parent->d_inode);
+ dput(parent);
+ }
}
- fuse_advise_use_readdirplus(inode);
return 1;
}
#include <linux/compat.h>
#include <linux/swap.h>
#include <linux/aio.h>
+#include <linux/falloc.h>
static const struct file_operations fuse_direct_io_file_operations;
iov_iter_init(&ii, iov, nr_segs, count, 0);
- req = fuse_get_req(fc, fuse_iter_npages(&ii));
+ if (io->async)
+ req = fuse_get_req_for_background(fc, fuse_iter_npages(&ii));
+ else
+ req = fuse_get_req(fc, fuse_iter_npages(&ii));
if (IS_ERR(req))
return PTR_ERR(req);
break;
if (count) {
fuse_put_request(fc, req);
- req = fuse_get_req(fc, fuse_iter_npages(&ii));
+ if (io->async)
+ req = fuse_get_req_for_background(fc,
+ fuse_iter_npages(&ii));
+ else
+ req = fuse_get_req(fc, fuse_iter_npages(&ii));
if (IS_ERR(req))
break;
}
fuse_do_setattr(inode, &attr, file);
}
+static inline loff_t fuse_round_up(loff_t off)
+{
+ return round_up(off, FUSE_MAX_PAGES_PER_REQ << PAGE_SHIFT);
+}
+
static ssize_t
fuse_direct_IO(int rw, struct kiocb *iocb, const struct iovec *iov,
loff_t offset, unsigned long nr_segs)
ssize_t ret = 0;
struct file *file = iocb->ki_filp;
struct fuse_file *ff = file->private_data;
+ bool async_dio = ff->fc->async_dio;
loff_t pos = 0;
struct inode *inode;
loff_t i_size;
i_size = i_size_read(inode);
/* optimization for short read */
- if (rw != WRITE && offset + count > i_size) {
+ if (async_dio && rw != WRITE && offset + count > i_size) {
if (offset >= i_size)
return 0;
- count = i_size - offset;
+ count = min_t(loff_t, count, fuse_round_up(i_size - offset));
}
io = kmalloc(sizeof(struct fuse_io_priv), GFP_KERNEL);
* By default, we want to optimize all I/Os with async request
* submission to the client filesystem if supported.
*/
- io->async = ff->fc->async_dio;
+ io->async = async_dio;
io->iocb = iocb;
/*
* to wait on real async I/O requests, so we must submit this request
* synchronously.
*/
- if (!is_sync_kiocb(iocb) && (offset + count > i_size))
+ if (!is_sync_kiocb(iocb) && (offset + count > i_size) && rw == WRITE)
io->async = false;
if (rw == WRITE)
fuse_aio_complete(io, ret < 0 ? ret : 0, -1);
/* we have a non-extending, async request, so return */
- if (ret > 0 && !is_sync_kiocb(iocb))
+ if (!is_sync_kiocb(iocb))
return -EIOCBQUEUED;
ret = wait_on_sync_kiocb(iocb);
loff_t length)
{
struct fuse_file *ff = file->private_data;
+ struct inode *inode = file->f_inode;
struct fuse_conn *fc = ff->fc;
struct fuse_req *req;
struct fuse_fallocate_in inarg = {
if (fc->no_fallocate)
return -EOPNOTSUPP;
+ if (mode & FALLOC_FL_PUNCH_HOLE) {
+ mutex_lock(&inode->i_mutex);
+ fuse_set_nowrite(inode);
+ }
+
req = fuse_get_req_nopages(fc);
- if (IS_ERR(req))
- return PTR_ERR(req);
+ if (IS_ERR(req)) {
+ err = PTR_ERR(req);
+ goto out;
+ }
req->in.h.opcode = FUSE_FALLOCATE;
req->in.h.nodeid = ff->nodeid;
}
fuse_put_request(fc, req);
+ if (err)
+ goto out;
+
+ /* we could have extended the file */
+ if (!(mode & FALLOC_FL_KEEP_SIZE))
+ fuse_write_update_size(inode, offset + length);
+
+ if (mode & FALLOC_FL_PUNCH_HOLE)
+ truncate_pagecache_range(inode, offset, offset + length - 1);
+
+ fuse_invalidate_attr(inode);
+
+out:
+ if (mode & FALLOC_FL_PUNCH_HOLE) {
+ fuse_release_nowrite(inode);
+ mutex_unlock(&inode->i_mutex);
+ }
+
return err;
}
fc->dont_mask = 1;
if (arg->flags & FUSE_AUTO_INVAL_DATA)
fc->auto_inval_data = 1;
- if (arg->flags & FUSE_DO_READDIRPLUS)
+ if (arg->flags & FUSE_DO_READDIRPLUS) {
fc->do_readdirplus = 1;
- if (arg->flags & FUSE_READDIRPLUS_AUTO)
- fc->readdirplus_auto = 1;
+ if (arg->flags & FUSE_READDIRPLUS_AUTO)
+ fc->readdirplus_auto = 1;
+ }
if (arg->flags & FUSE_ASYNC_DIO)
fc->async_dio = 1;
} else {
config GFS2_FS_LOCKING_DLM
bool "GFS2 DLM locking"
depends on (GFS2_FS!=n) && NET && INET && (IPV6 || IPV6=n) && \
- HOTPLUG && DLM && CONFIGFS_FS && SYSFS
+ HOTPLUG && CONFIGFS_FS && SYSFS && (DLM=y || DLM=GFS2_FS)
help
Multiple node locking module for GFS2
if (ret)
return ret;
+ ret = get_write_access(inode);
+ if (ret)
+ return ret;
+
inode_dio_wait(inode);
ret = gfs2_rs_alloc(GFS2_I(inode));
if (ret)
- return ret;
+ goto out;
oldsize = inode->i_size;
- if (newsize >= oldsize)
- return do_grow(inode, newsize);
+ if (newsize >= oldsize) {
+ ret = do_grow(inode, newsize);
+ goto out;
+ }
- return do_shrink(inode, oldsize, newsize);
+ ret = do_shrink(inode, oldsize, newsize);
+out:
+ put_write_access(inode);
+ return ret;
}
int gfs2_truncatei_resume(struct gfs2_inode *ip)
return ERR_PTR(-EIO);
}
- hc = kmalloc(hsize, GFP_NOFS);
- ret = -ENOMEM;
+ hc = kmalloc(hsize, GFP_NOFS | __GFP_NOWARN);
+ if (hc == NULL)
+ hc = __vmalloc(hsize, GFP_NOFS, PAGE_KERNEL);
+
if (hc == NULL)
return ERR_PTR(-ENOMEM);
ret = gfs2_dir_read_data(ip, hc, hsize);
if (ret < 0) {
- kfree(hc);
+ if (is_vmalloc_addr(hc))
+ vfree(hc);
+ else
+ kfree(hc);
return ERR_PTR(ret);
}
spin_lock(&inode->i_lock);
- if (ip->i_hash_cache)
- kfree(hc);
- else
+ if (ip->i_hash_cache) {
+ if (is_vmalloc_addr(hc))
+ vfree(hc);
+ else
+ kfree(hc);
+ } else {
ip->i_hash_cache = hc;
+ }
spin_unlock(&inode->i_lock);
return ip->i_hash_cache;
{
__be64 *hc = ip->i_hash_cache;
ip->i_hash_cache = NULL;
- kfree(hc);
+ if (is_vmalloc_addr(hc))
+ vfree(hc);
+ else
+ kfree(hc);
}
static inline int gfs2_dirent_sentinel(const struct gfs2_dirent *dent)
if (IS_ERR(hc))
return PTR_ERR(hc);
- h = hc2 = kmalloc(hsize_bytes * 2, GFP_NOFS);
+ h = hc2 = kmalloc(hsize_bytes * 2, GFP_NOFS | __GFP_NOWARN);
+ if (hc2 == NULL)
+ hc2 = __vmalloc(hsize_bytes * 2, GFP_NOFS, PAGE_KERNEL);
+
if (!hc2)
return -ENOMEM;
gfs2_dinode_out(dip, dibh->b_data);
brelse(dibh);
out_kfree:
- kfree(hc2);
+ if (is_vmalloc_addr(hc2))
+ vfree(hc2);
+ else
+ kfree(hc2);
return error;
}
memset(&rlist, 0, sizeof(struct gfs2_rgrp_list));
ht = kzalloc(size, GFP_NOFS);
+ if (ht == NULL)
+ ht = vzalloc(size);
if (!ht)
return -ENOMEM;
gfs2_rlist_free(&rlist);
gfs2_quota_unhold(dip);
out:
- kfree(ht);
+ if (is_vmalloc_addr(ht))
+ vfree(ht);
+ else
+ kfree(ht);
return error;
}
/* Update file times before taking page lock */
file_update_time(vma->vm_file);
+ ret = get_write_access(inode);
+ if (ret)
+ goto out;
+
ret = gfs2_rs_alloc(ip);
if (ret)
- return ret;
+ goto out_write_access;
gfs2_size_hint(vma->vm_file, pos, PAGE_CACHE_SIZE);
gfs2_holder_init(ip->i_gl, LM_ST_EXCLUSIVE, 0, &gh);
ret = gfs2_glock_nq(&gh);
if (ret)
- goto out;
+ goto out_uninit;
set_bit(GLF_DIRTY, &ip->i_gl->gl_flags);
set_bit(GIF_SW_PAGED, &ip->i_flags);
gfs2_quota_unlock(ip);
out_unlock:
gfs2_glock_dq(&gh);
-out:
+out_uninit:
gfs2_holder_uninit(&gh);
if (ret == 0) {
set_page_dirty(page);
wait_for_stable_page(page);
}
+out_write_access:
+ put_write_access(inode);
+out:
sb_end_pagefault(inode->i_sb);
return block_page_mkwrite_return(ret);
}
kfree(file->private_data);
file->private_data = NULL;
- if ((file->f_mode & FMODE_WRITE) &&
- (atomic_read(&inode->i_writecount) == 1))
- gfs2_rs_delete(ip);
+ if (!(file->f_mode & FMODE_WRITE))
+ return 0;
+ gfs2_rs_delete(ip);
return 0;
}
return inode;
fail_refresh:
+ ip->i_iopen_gh.gh_flags |= GL_NOCACHE;
ip->i_iopen_gh.gh_gl->gl_object = NULL;
gfs2_glock_dq_uninit(&ip->i_iopen_gh);
fail_iopen:
fs_err(sdp, "Error %d writing to log\n", error);
}
- bio_for_each_segment(bvec, bio, i) {
+ bio_for_each_segment_all(bvec, bio, i) {
page = bvec->bv_page;
if (page_has_buffers(page))
gfs2_end_log_write_bh(sdp, bvec, error);
if (total > limit)
num = limit;
gfs2_log_unlock(sdp);
- page = gfs2_get_log_desc(sdp, GFS2_LOG_DESC_METADATA, num + 1, num);
+ page = gfs2_get_log_desc(sdp,
+ is_databuf ? GFS2_LOG_DESC_JDATA :
+ GFS2_LOG_DESC_METADATA, num + 1, num);
ld = page_address(page);
gfs2_log_lock(sdp);
ptr = (__be64 *)(ld + 1);
{
struct kqid qid = qd->qd_id;
return (2 * (u64)from_kqid(&init_user_ns, qid)) +
- (qid.type == USRQUOTA) ? 0 : 1;
+ ((qid.type == USRQUOTA) ? 0 : 1);
}
static u64 qd2offset(struct gfs2_quota_data *qd)
goto unlock_out;
}
- gfs2_trans_add_meta(ip->i_gl, bh);
+ gfs2_trans_add_data(ip->i_gl, bh);
kaddr = kmap_atomic(page);
if (offset + sizeof(struct gfs2_quota) > PAGE_CACHE_SIZE)
*/
void gfs2_rs_delete(struct gfs2_inode *ip)
{
+ struct inode *inode = &ip->i_inode;
+
down_write(&ip->i_rw_mutex);
- if (ip->i_res) {
+ if (ip->i_res && atomic_read(&inode->i_writecount) <= 1) {
gfs2_rs_deltree(ip->i_res);
BUG_ON(ip->i_res->rs_free);
kmem_cache_free(gfs2_rsrv_cachep, ip->i_res);
u32 extlen;
u32 free_blocks = rgd->rd_free_clone - rgd->rd_reserved;
int ret;
+ struct inode *inode = &ip->i_inode;
- extlen = max_t(u32, atomic_read(&rs->rs_sizehint), requested);
- extlen = clamp(extlen, RGRP_RSRV_MINBLKS, free_blocks);
+ if (S_ISDIR(inode->i_mode))
+ extlen = 1;
+ else {
+ extlen = max_t(u32, atomic_read(&rs->rs_sizehint), requested);
+ extlen = clamp(extlen, RGRP_RSRV_MINBLKS, free_blocks);
+ }
if ((rgd->rd_free_clone < rgd->rd_reserved) || (free_blocks < extlen))
return;
/* Must not read inode block until block type has been verified */
error = gfs2_glock_nq_init(ip->i_gl, LM_ST_EXCLUSIVE, GL_SKIP, &gh);
if (unlikely(error)) {
+ ip->i_iopen_gh.gh_flags |= GL_NOCACHE;
gfs2_glock_dq_uninit(&ip->i_iopen_gh);
goto out;
}
if (gfs2_rs_active(ip->i_res))
gfs2_rs_deltree(ip->i_res);
- if (test_bit(HIF_HOLDER, &ip->i_iopen_gh.gh_iflags))
+ if (test_bit(HIF_HOLDER, &ip->i_iopen_gh.gh_iflags)) {
+ ip->i_iopen_gh.gh_flags |= GL_NOCACHE;
gfs2_glock_dq(&ip->i_iopen_gh);
+ }
gfs2_holder_uninit(&ip->i_iopen_gh);
gfs2_glock_dq_uninit(&gh);
if (error && error != GLR_TRYFAILED && error != -EROFS)
ip->i_gl = NULL;
if (ip->i_iopen_gh.gh_gl) {
ip->i_iopen_gh.gh_gl->gl_object = NULL;
+ ip->i_iopen_gh.gh_flags |= GL_NOCACHE;
gfs2_glock_dq_uninit(&ip->i_iopen_gh);
}
}
spin_lock(&tree->hash_lock);
node = hfs_bnode_findhash(tree, num);
spin_unlock(&tree->hash_lock);
- BUG_ON(node);
+ if (node) {
+ pr_crit("new node %u already hashed?\n", num);
+ WARN_ON(1);
+ return node;
+ }
node = __hfs_bnode_create(tree, num);
if (!node)
return ERR_PTR(-ENOMEM);
if (whence == SEEK_DATA || whence == SEEK_HOLE)
return -EINVAL;
+ mutex_lock(&i->i_mutex);
hpfs_lock(s);
/*printk("dir lseek\n");*/
if (new_off == 0 || new_off == 1 || new_off == 11 || new_off == 12 || new_off == 13) goto ok;
- mutex_lock(&i->i_mutex);
pos = ((loff_t) hpfs_de_as_down_as_possible(s, hpfs_inode->i_dno) << 4) + 1;
while (pos != new_off) {
if (map_pos_dirent(i, &pos, &qbh)) hpfs_brelse4(&qbh);
else goto fail;
if (pos == 12) goto fail;
}
- mutex_unlock(&i->i_mutex);
+ hpfs_add_pos(i, &filp->f_pos);
ok:
+ filp->f_pos = new_off;
hpfs_unlock(s);
- return filp->f_pos = new_off;
-fail:
mutex_unlock(&i->i_mutex);
+ return new_off;
+fail:
/*printk("illegal lseek: %016llx\n", new_off);*/
hpfs_unlock(s);
+ mutex_unlock(&i->i_mutex);
return -ESPIPE;
}
bio->bi_end_io = lbmIODone;
bio->bi_private = bp;
- submit_bio(READ_SYNC, bio);
+ /*check if journaling to disk has been disabled*/
+ if (log->no_integrity) {
+ bio->bi_size = 0;
+ lbmIODone(bio, 0);
+ } else {
+ submit_bio(READ_SYNC, bio);
+ }
wait_event(bp->l_ioevent, (bp->l_flag != lbmREAD));
{
struct jfs_sb_info *sbi = JFS_SBI(sb);
struct jfs_log *log = sbi->log;
+ int rc = 0;
if (!(sb->s_flags & MS_RDONLY)) {
txQuiesce(sb);
- lmLogShutdown(log);
- updateSuper(sb, FM_CLEAN);
+ rc = lmLogShutdown(log);
+ if (rc) {
+ jfs_error(sb, "jfs_freeze: lmLogShutdown failed");
+
+ /* let operations fail rather than hang */
+ txResume(sb);
+
+ return rc;
+ }
+ rc = updateSuper(sb, FM_CLEAN);
+ if (rc) {
+ jfs_err("jfs_freeze: updateSuper failed\n");
+ /*
+ * Don't fail here. Everything succeeded except
+ * marking the superblock clean, so there's really
+ * no harm in leaving it frozen for now.
+ */
+ }
}
return 0;
}
int rc = 0;
if (!(sb->s_flags & MS_RDONLY)) {
- updateSuper(sb, FM_MOUNT);
- if ((rc = lmLogInit(log)))
- jfs_err("jfs_unlock failed with return code %d", rc);
- else
- txResume(sb);
+ rc = updateSuper(sb, FM_MOUNT);
+ if (rc) {
+ jfs_error(sb, "jfs_unfreeze: updateSuper failed");
+ goto out;
+ }
+ rc = lmLogInit(log);
+ if (rc)
+ jfs_error(sb, "jfs_unfreeze: lmLogInit failed");
+out:
+ txResume(sb);
}
- return 0;
+ return rc;
}
static struct dentry *jfs_do_mount(struct file_system_type *fs_type,
spin_lock(&tbl->slot_tbl_lock);
/* state manager is resetting the session */
- if (test_bit(NFS4_SESSION_DRAINING, &clp->cl_session->session_state)) {
+ if (test_bit(NFS4_SLOT_TBL_DRAINING, &tbl->slot_tbl_state)) {
spin_unlock(&tbl->slot_tbl_lock);
status = htonl(NFS4ERR_DELAY);
/* Return NFS4ERR_BADSESSION if we're draining the session
* A single slot, so highest used slotid is either 0 or -1
*/
tbl->highest_used_slotid = NFS4_NO_SLOT;
- nfs4_session_drain_complete(session, tbl);
+ nfs4_slot_tbl_drain_complete(tbl);
spin_unlock(&tbl->slot_tbl_lock);
}
__set_bit(NFS_CS_DISCRTRY, &clp->cl_flags);
error = nfs_create_rpc_client(clp, timeparms, RPC_AUTH_GSS_KRB5I);
if (error == -EINVAL)
- error = nfs_create_rpc_client(clp, timeparms, RPC_AUTH_NULL);
+ error = nfs_create_rpc_client(clp, timeparms, RPC_AUTH_UNIX);
if (error < 0)
goto error;
task->tk_timeout = 0;
spin_lock(&tbl->slot_tbl_lock);
- if (test_bit(NFS4_SESSION_DRAINING, &session->session_state) &&
+ if (test_bit(NFS4_SLOT_TBL_DRAINING, &tbl->slot_tbl_state) &&
!args->sa_privileged) {
/* The state manager will wait until the slot table is empty */
dprintk("%s session is draining\n", __func__);
struct nfs4_state *state = opendata->state;
struct nfs_inode *nfsi = NFS_I(state->inode);
struct nfs_delegation *delegation;
- int open_mode = opendata->o_arg.open_flags & (O_EXCL|O_TRUNC);
+ int open_mode = opendata->o_arg.open_flags;
fmode_t fmode = opendata->o_arg.fmode;
nfs4_stateid stateid;
int ret = -EAGAIN;
tbl->highest_used_slotid = new_max;
else {
tbl->highest_used_slotid = NFS4_NO_SLOT;
- nfs4_session_drain_complete(tbl->session, tbl);
+ nfs4_slot_tbl_drain_complete(tbl);
}
}
dprintk("%s: slotid %u highest_used_slotid %d\n", __func__,
struct nfs4_slot *slot = pslot;
struct nfs4_slot_table *tbl = slot->table;
- if (nfs4_session_draining(tbl->session) && !args->sa_privileged)
+ if (nfs4_slot_tbl_draining(tbl) && !args->sa_privileged)
return false;
slot->generation = tbl->generation;
args->sa_slot = slot;
};
/* Sessions */
+enum nfs4_slot_tbl_state {
+ NFS4_SLOT_TBL_DRAINING,
+};
+
#define SLOT_TABLE_SZ DIV_ROUND_UP(NFS4_MAX_SLOT_TABLE, 8*sizeof(long))
struct nfs4_slot_table {
struct nfs4_session *session; /* Parent session */
unsigned long generation; /* Generation counter for
target_highest_slotid */
struct completion complete;
+ unsigned long slot_tbl_state;
};
/*
enum nfs4_session_state {
NFS4_SESSION_INITING,
- NFS4_SESSION_DRAINING,
};
#if defined(CONFIG_NFS_V4_1)
extern int nfs4_init_session(struct nfs_server *server);
extern int nfs4_init_ds_session(struct nfs_client *, unsigned long);
-extern void nfs4_session_drain_complete(struct nfs4_session *session,
- struct nfs4_slot_table *tbl);
+extern void nfs4_slot_tbl_drain_complete(struct nfs4_slot_table *tbl);
-static inline bool nfs4_session_draining(struct nfs4_session *session)
+static inline bool nfs4_slot_tbl_draining(struct nfs4_slot_table *tbl)
{
- return !!test_bit(NFS4_SESSION_DRAINING, &session->session_state);
+ return !!test_bit(NFS4_SLOT_TBL_DRAINING, &tbl->slot_tbl_state);
}
bool nfs41_wake_and_assign_slot(struct nfs4_slot_table *tbl,
if (ses == NULL)
return;
tbl = &ses->fc_slot_table;
- if (test_and_clear_bit(NFS4_SESSION_DRAINING, &ses->session_state)) {
+ if (test_and_clear_bit(NFS4_SLOT_TBL_DRAINING, &tbl->slot_tbl_state)) {
spin_lock(&tbl->slot_tbl_lock);
nfs41_wake_slot_table(tbl);
spin_unlock(&tbl->slot_tbl_lock);
/*
* Signal state manager thread if session fore channel is drained
*/
-void nfs4_session_drain_complete(struct nfs4_session *session,
- struct nfs4_slot_table *tbl)
+void nfs4_slot_tbl_drain_complete(struct nfs4_slot_table *tbl)
{
- if (nfs4_session_draining(session))
+ if (nfs4_slot_tbl_draining(tbl))
complete(&tbl->complete);
}
-static int nfs4_wait_on_slot_tbl(struct nfs4_slot_table *tbl)
+static int nfs4_drain_slot_tbl(struct nfs4_slot_table *tbl)
{
+ set_bit(NFS4_SLOT_TBL_DRAINING, &tbl->slot_tbl_state);
spin_lock(&tbl->slot_tbl_lock);
if (tbl->highest_used_slotid != NFS4_NO_SLOT) {
INIT_COMPLETION(tbl->complete);
struct nfs4_session *ses = clp->cl_session;
int ret = 0;
- set_bit(NFS4_SESSION_DRAINING, &ses->session_state);
/* back channel */
- ret = nfs4_wait_on_slot_tbl(&ses->bc_slot_table);
+ ret = nfs4_drain_slot_tbl(&ses->bc_slot_table);
if (ret)
return ret;
/* fore channel */
- return nfs4_wait_on_slot_tbl(&ses->fc_slot_table);
+ return nfs4_drain_slot_tbl(&ses->fc_slot_table);
}
static void nfs41_finish_session_reset(struct nfs_client *clp)
args->namlen = data->namlen;
args->bsize = data->bsize;
+ args->auth_flavors[0] = RPC_AUTH_UNIX;
if (data->flags & NFS_MOUNT_SECFLAVOUR)
args->auth_flavors[0] = data->pseudoflavor;
if (!args->nfs_server.hostname)
goto out_no_address;
args->nfs_server.port = ntohs(((struct sockaddr_in *)sap)->sin_port);
+ args->auth_flavors[0] = RPC_AUTH_UNIX;
if (data->auth_flavourlen) {
if (data->auth_flavourlen > 1)
goto out_inval_auth;
static int nilfs_set_page_dirty(struct page *page)
{
- int ret = __set_page_dirty_buffers(page);
+ int ret = __set_page_dirty_nobuffers(page);
- if (ret) {
+ if (page_has_buffers(page)) {
struct inode *inode = page->mapping->host;
- unsigned nr_dirty = 1 << (PAGE_SHIFT - inode->i_blkbits);
+ unsigned nr_dirty = 0;
+ struct buffer_head *bh, *head;
- nilfs_set_file_dirty(inode, nr_dirty);
+ /*
+ * This page is locked by callers, and no other thread
+ * concurrently marks its buffers dirty since they are
+ * only dirtied through routines in fs/buffer.c in
+ * which call sites of mark_buffer_dirty are protected
+ * by page lock.
+ */
+ bh = head = page_buffers(page);
+ do {
+ /* Do not mark hole blocks dirty */
+ if (buffer_dirty(bh) || !buffer_mapped(bh))
+ continue;
+
+ set_buffer_dirty(bh);
+ nr_dirty++;
+ } while (bh = bh->b_this_page, bh != head);
+
+ if (nr_dirty)
+ nilfs_set_file_dirty(inode, nr_dirty);
}
return ret;
}
&hole_size, &rec, &is_last);
if (ret) {
mlog_errno(ret);
- goto out;
+ goto out_unlock;
}
if (rec.e_blkno == 0ULL) {
ret = ocfs2_inode_lock(inode, NULL, 1);
if (ret < 0) {
mlog_errno(ret);
- goto out_sems;
+ goto out;
}
ocfs2_inode_unlock(inode, 1);
if (peer_mnt == mnt)
peer_mnt = NULL;
}
- if (IS_MNT_SHARED(mnt) && list_empty(&mnt->mnt_share))
+ if (mnt->mnt_group_id && IS_MNT_SHARED(mnt) &&
+ list_empty(&mnt->mnt_share))
mnt_release_group_id(mnt);
list_del_init(&mnt->mnt_share);
struct inode *inode = file_inode(filp);
struct super_block *s = inode->i_sb;
struct qnx6_sb_info *sbi = QNX6_SB(s);
- loff_t pos = filp->f_pos & (QNX6_DIR_ENTRY_SIZE - 1);
+ loff_t pos = filp->f_pos & ~(QNX6_DIR_ENTRY_SIZE - 1);
unsigned long npages = dir_pages(inode);
unsigned long n = pos >> PAGE_CACHE_SHIFT;
unsigned start = (pos & ~PAGE_CACHE_MASK) / QNX6_DIR_ENTRY_SIZE;
next_pos = deh_offset(deh) + 1;
if (item_moved(&tmp_ih, &path_to_entry)) {
+ set_cpu_key_k_offset(&pos_key,
+ next_pos);
goto research;
}
} /* for */
TYPE_STAT_DATA, SD_SIZE, MAX_US_INT);
memcpy(INODE_PKEY(inode), &(ih.ih_key), KEY_SIZE);
args.dirid = le32_to_cpu(ih.ih_key.k_dir_id);
- if (insert_inode_locked4(inode, args.objectid,
- reiserfs_find_actor, &args) < 0) {
+
+ reiserfs_write_unlock(inode->i_sb);
+ err = insert_inode_locked4(inode, args.objectid,
+ reiserfs_find_actor, &args);
+ reiserfs_write_lock(inode->i_sb);
+ if (err) {
err = -EINVAL;
goto out_bad_inode;
}
+
if (old_format_only(sb))
/* not a perfect generation count, as object ids can be reused, but
** this is as good as reiserfs can do right now.
static int chown_one_xattr(struct dentry *dentry, void *data)
{
struct iattr *attrs = data;
- return reiserfs_setattr(dentry, attrs);
+ int ia_valid = attrs->ia_valid;
+ int err;
+
+ /*
+ * We only want the ownership bits. Otherwise, we'll do
+ * things like change a directory to a regular file if
+ * ATTR_MODE is set.
+ */
+ attrs->ia_valid &= (ATTR_UID|ATTR_GID);
+ err = reiserfs_setattr(dentry, attrs);
+ attrs->ia_valid = ia_valid;
+
+ return err;
}
/* No i_mutex, but the inode is unconnected. */
int depth;
int error;
+ if (IS_PRIVATE(inode))
+ return 0;
+
if (S_ISLNK(inode->i_mode))
return -EOPNOTSUPP;
#include "xfs_bmap_btree.h"
#include "xfs_inode.h"
#include "xfs_vnodeops.h"
+#include "xfs_sb.h"
+#include "xfs_mount.h"
#include "xfs_trace.h"
#include <linux/slab.h>
#include <linux/xattr.h>
*/
STATIC struct posix_acl *
-xfs_acl_from_disk(struct xfs_acl *aclp)
+xfs_acl_from_disk(
+ struct xfs_acl *aclp,
+ int max_entries)
{
struct posix_acl_entry *acl_e;
struct posix_acl *acl;
unsigned int count, i;
count = be32_to_cpu(aclp->acl_cnt);
- if (count > XFS_ACL_MAX_ENTRIES)
+ if (count > max_entries)
return ERR_PTR(-EFSCORRUPTED);
acl = posix_acl_alloc(count, GFP_KERNEL);
struct xfs_inode *ip = XFS_I(inode);
struct posix_acl *acl;
struct xfs_acl *xfs_acl;
- int len = sizeof(struct xfs_acl);
unsigned char *ea_name;
int error;
+ int len;
acl = get_cached_acl(inode, type);
if (acl != ACL_NOT_CACHED)
* If we have a cached ACLs value just return it, not need to
* go out to the disk.
*/
-
- xfs_acl = kzalloc(sizeof(struct xfs_acl), GFP_KERNEL);
+ len = XFS_ACL_MAX_SIZE(ip->i_mount);
+ xfs_acl = kzalloc(len, GFP_KERNEL);
if (!xfs_acl)
return ERR_PTR(-ENOMEM);
goto out;
}
- acl = xfs_acl_from_disk(xfs_acl);
+ acl = xfs_acl_from_disk(xfs_acl, XFS_ACL_MAX_ENTRIES(ip->i_mount));
if (IS_ERR(acl))
goto out;
if (acl) {
struct xfs_acl *xfs_acl;
- int len;
+ int len = XFS_ACL_MAX_SIZE(ip->i_mount);
- xfs_acl = kzalloc(sizeof(struct xfs_acl), GFP_KERNEL);
+ xfs_acl = kzalloc(len, GFP_KERNEL);
if (!xfs_acl)
return -ENOMEM;
xfs_acl_to_disk(xfs_acl, acl);
- len = sizeof(struct xfs_acl) -
- (sizeof(struct xfs_acl_entry) *
- (XFS_ACL_MAX_ENTRIES - acl->a_count));
+
+ /* subtract away the unused acl entries */
+ len -= sizeof(struct xfs_acl_entry) *
+ (XFS_ACL_MAX_ENTRIES(ip->i_mount) - acl->a_count);
error = -xfs_attr_set(ip, ea_name, (unsigned char *)xfs_acl,
len, ATTR_ROOT);
static int
xfs_acl_exists(struct inode *inode, unsigned char *name)
{
- int len = sizeof(struct xfs_acl);
+ int len = XFS_ACL_MAX_SIZE(XFS_M(inode->i_sb));
return (xfs_attr_get(XFS_I(inode), name, NULL, &len,
ATTR_ROOT|ATTR_KERNOVAL) == 0);
goto out_release;
error = -EINVAL;
- if (acl->a_count > XFS_ACL_MAX_ENTRIES)
+ if (acl->a_count > XFS_ACL_MAX_ENTRIES(XFS_M(inode->i_sb)))
goto out_release;
if (type == ACL_TYPE_ACCESS) {
struct posix_acl;
struct xfs_inode;
-#define XFS_ACL_MAX_ENTRIES 25
#define XFS_ACL_NOT_PRESENT (-1)
/* On-disk XFS access control list structure */
+struct xfs_acl_entry {
+ __be32 ae_tag;
+ __be32 ae_id;
+ __be16 ae_perm;
+ __be16 ae_pad; /* fill the implicit hole in the structure */
+};
+
struct xfs_acl {
- __be32 acl_cnt;
- struct xfs_acl_entry {
- __be32 ae_tag;
- __be32 ae_id;
- __be16 ae_perm;
- } acl_entry[XFS_ACL_MAX_ENTRIES];
+ __be32 acl_cnt;
+ struct xfs_acl_entry acl_entry[0];
};
+/*
+ * The number of ACL entries allowed is defined by the on-disk format.
+ * For v4 superblocks, that is limited to 25 entries. For v5 superblocks, it is
+ * limited only by the maximum size of the xattr that stores the information.
+ */
+#define XFS_ACL_MAX_ENTRIES(mp) \
+ (xfs_sb_version_hascrc(&mp->m_sb) \
+ ? (XATTR_SIZE_MAX - sizeof(struct xfs_acl)) / \
+ sizeof(struct xfs_acl_entry) \
+ : 25)
+
+#define XFS_ACL_MAX_SIZE(mp) \
+ (sizeof(struct xfs_acl) + \
+ sizeof(struct xfs_acl_entry) * XFS_ACL_MAX_ENTRIES((mp)))
+
/* On-disk XFS extended attribute names */
#define SGI_ACL_FILE (unsigned char *)"SGI_ACL_FILE"
#define SGI_ACL_DEFAULT (unsigned char *)"SGI_ACL_DEFAULT"
(xfs_off_t)(page->index + 1) << PAGE_CACHE_SHIFT,
i_size_read(inode));
+ /*
+ * If the current map does not span the entire page we are about to try
+ * to write, then give up. The only way we can write a page that spans
+ * multiple mappings in a single writeback iteration is via the
+ * xfs_vm_writepage() function. Data integrity writeback requires the
+ * entire page to be written in a single attempt, otherwise the part of
+ * the page we don't write here doesn't get written as part of the data
+ * integrity sync.
+ *
+ * For normal writeback, we also don't attempt to write partial pages
+ * here as it simply means that write_cache_pages() will see it under
+ * writeback and ignore the page until some point in the future, at
+ * which time this will be the only page in the file that needs
+ * writeback. Hence for more optimal IO patterns, we should always
+ * avoid partial page writeback due to multiple mappings on a page here.
+ */
+ if (!xfs_imap_valid(inode, imap, end_offset))
+ goto fail_unlock_page;
+
len = 1 << inode->i_blkbits;
p_offset = min_t(unsigned long, end_offset & (PAGE_CACHE_SIZE - 1),
PAGE_CACHE_SIZE);
*/
int
xfs_attr_shortform_allfit(
- struct xfs_buf *bp,
- struct xfs_inode *dp)
+ struct xfs_buf *bp,
+ struct xfs_inode *dp)
{
- xfs_attr_leafblock_t *leaf;
- xfs_attr_leaf_entry_t *entry;
+ struct xfs_attr_leafblock *leaf;
+ struct xfs_attr_leaf_entry *entry;
xfs_attr_leaf_name_local_t *name_loc;
- int bytes, i;
+ struct xfs_attr3_icleaf_hdr leafhdr;
+ int bytes;
+ int i;
leaf = bp->b_addr;
- ASSERT(leaf->hdr.info.magic == cpu_to_be16(XFS_ATTR_LEAF_MAGIC));
+ xfs_attr3_leaf_hdr_from_disk(&leafhdr, leaf);
+ entry = xfs_attr3_leaf_entryp(leaf);
- entry = &leaf->entries[0];
bytes = sizeof(struct xfs_attr_sf_hdr);
- for (i = 0; i < be16_to_cpu(leaf->hdr.count); entry++, i++) {
+ for (i = 0; i < leafhdr.count; entry++, i++) {
if (entry->flags & XFS_ATTR_INCOMPLETE)
continue; /* don't copy partial entries */
if (!(entry->flags & XFS_ATTR_LOCAL))
return(0);
if (be16_to_cpu(name_loc->valuelen) >= XFS_ATTR_SF_ENTSIZE_MAX)
return(0);
- bytes += sizeof(struct xfs_attr_sf_entry)-1
+ bytes += sizeof(struct xfs_attr_sf_entry) - 1
+ name_loc->namelen
+ be16_to_cpu(name_loc->valuelen);
}
if ((dp->i_mount->m_flags & XFS_MOUNT_ATTR2) &&
(dp->i_d.di_format != XFS_DINODE_FMT_BTREE) &&
(bytes == sizeof(struct xfs_attr_sf_hdr)))
- return(-1);
- return(xfs_attr_shortform_bytesfit(dp, bytes));
+ return -1;
+ return xfs_attr_shortform_bytesfit(dp, bytes);
}
/*
name_rmt->valuelen = 0;
name_rmt->valueblk = 0;
args->rmtblkno = 1;
- args->rmtblkcnt = XFS_B_TO_FSB(mp, args->valuelen);
+ args->rmtblkcnt = xfs_attr3_rmt_blocks(mp, args->valuelen);
}
xfs_trans_log_buf(args->trans, bp,
XFS_DA_LOGRANGE(leaf, xfs_attr3_leaf_name(leaf, args->index),
STATIC void
xfs_attr3_leaf_compact(
struct xfs_da_args *args,
- struct xfs_attr3_icleaf_hdr *ichdr_d,
+ struct xfs_attr3_icleaf_hdr *ichdr_dst,
struct xfs_buf *bp)
{
- xfs_attr_leafblock_t *leaf_s, *leaf_d;
- struct xfs_attr3_icleaf_hdr ichdr_s;
+ struct xfs_attr_leafblock *leaf_src;
+ struct xfs_attr_leafblock *leaf_dst;
+ struct xfs_attr3_icleaf_hdr ichdr_src;
struct xfs_trans *trans = args->trans;
struct xfs_mount *mp = trans->t_mountp;
char *tmpbuffer;
trace_xfs_attr_leaf_compact(args);
tmpbuffer = kmem_alloc(XFS_LBSIZE(mp), KM_SLEEP);
- ASSERT(tmpbuffer != NULL);
memcpy(tmpbuffer, bp->b_addr, XFS_LBSIZE(mp));
memset(bp->b_addr, 0, XFS_LBSIZE(mp));
+ leaf_src = (xfs_attr_leafblock_t *)tmpbuffer;
+ leaf_dst = bp->b_addr;
/*
- * Copy basic information
+ * Copy the on-disk header back into the destination buffer to ensure
+ * all the information in the header that is not part of the incore
+ * header structure is preserved.
*/
- leaf_s = (xfs_attr_leafblock_t *)tmpbuffer;
- leaf_d = bp->b_addr;
- ichdr_s = *ichdr_d; /* struct copy */
- ichdr_d->firstused = XFS_LBSIZE(mp);
- ichdr_d->usedbytes = 0;
- ichdr_d->count = 0;
- ichdr_d->holes = 0;
- ichdr_d->freemap[0].base = xfs_attr3_leaf_hdr_size(leaf_s);
- ichdr_d->freemap[0].size = ichdr_d->firstused - ichdr_d->freemap[0].base;
+ memcpy(bp->b_addr, tmpbuffer, xfs_attr3_leaf_hdr_size(leaf_src));
+
+ /* Initialise the incore headers */
+ ichdr_src = *ichdr_dst; /* struct copy */
+ ichdr_dst->firstused = XFS_LBSIZE(mp);
+ ichdr_dst->usedbytes = 0;
+ ichdr_dst->count = 0;
+ ichdr_dst->holes = 0;
+ ichdr_dst->freemap[0].base = xfs_attr3_leaf_hdr_size(leaf_src);
+ ichdr_dst->freemap[0].size = ichdr_dst->firstused -
+ ichdr_dst->freemap[0].base;
+
+
+ /* write the header back to initialise the underlying buffer */
+ xfs_attr3_leaf_hdr_to_disk(leaf_dst, ichdr_dst);
/*
* Copy all entry's in the same (sorted) order,
* but allocate name/value pairs packed and in sequence.
*/
- xfs_attr3_leaf_moveents(leaf_s, &ichdr_s, 0, leaf_d, ichdr_d, 0,
- ichdr_s.count, mp);
+ xfs_attr3_leaf_moveents(leaf_src, &ichdr_src, 0, leaf_dst, ichdr_dst, 0,
+ ichdr_src.count, mp);
/*
* this logs the entire buffer, but the caller must write the header
* back to the buffer when it is finished modifying it.
struct xfs_attr_leafblock *tmp_leaf;
struct xfs_attr3_icleaf_hdr tmphdr;
- tmp_leaf = kmem_alloc(state->blocksize, KM_SLEEP);
- memset(tmp_leaf, 0, state->blocksize);
- memset(&tmphdr, 0, sizeof(tmphdr));
+ tmp_leaf = kmem_zalloc(state->blocksize, KM_SLEEP);
+
+ /*
+ * Copy the header into the temp leaf so that all the stuff
+ * not in the incore header is present and gets copied back in
+ * once we've moved all the entries.
+ */
+ memcpy(tmp_leaf, save_leaf, xfs_attr3_leaf_hdr_size(save_leaf));
+ memset(&tmphdr, 0, sizeof(tmphdr));
tmphdr.magic = savehdr.magic;
tmphdr.forw = savehdr.forw;
tmphdr.back = savehdr.back;
tmphdr.firstused = state->blocksize;
+
+ /* write the header to the temp buffer to initialise it */
+ xfs_attr3_leaf_hdr_to_disk(tmp_leaf, &tmphdr);
+
if (xfs_attr3_leaf_order(save_blk->bp, &savehdr,
drop_blk->bp, &drophdr)) {
xfs_attr3_leaf_moveents(drop_leaf, &drophdr, 0,
if (!xfs_attr_namesp_match(args->flags, entry->flags))
continue;
args->index = probe;
+ args->valuelen = be32_to_cpu(name_rmt->valuelen);
args->rmtblkno = be32_to_cpu(name_rmt->valueblk);
- args->rmtblkcnt = XFS_B_TO_FSB(args->dp->i_mount,
- be32_to_cpu(name_rmt->valuelen));
+ args->rmtblkcnt = xfs_attr3_rmt_blocks(
+ args->dp->i_mount,
+ args->valuelen);
return XFS_ERROR(EEXIST);
}
}
ASSERT(memcmp(args->name, name_rmt->name, args->namelen) == 0);
valuelen = be32_to_cpu(name_rmt->valuelen);
args->rmtblkno = be32_to_cpu(name_rmt->valueblk);
- args->rmtblkcnt = XFS_B_TO_FSB(args->dp->i_mount, valuelen);
+ args->rmtblkcnt = xfs_attr3_rmt_blocks(args->dp->i_mount,
+ valuelen);
if (args->flags & ATTR_KERNOVAL) {
args->valuelen = valuelen;
return 0;
args.valuelen = valuelen;
args.value = kmem_alloc(valuelen, KM_SLEEP | KM_NOFS);
args.rmtblkno = be32_to_cpu(name_rmt->valueblk);
- args.rmtblkcnt = XFS_B_TO_FSB(args.dp->i_mount, valuelen);
+ args.rmtblkcnt = xfs_attr3_rmt_blocks(
+ args.dp->i_mount, valuelen);
retval = xfs_attr_rmtval_get(&args);
if (retval)
return retval;
name_rmt = xfs_attr3_leaf_name_remote(leaf, i);
if (name_rmt->valueblk) {
lp->valueblk = be32_to_cpu(name_rmt->valueblk);
- lp->valuelen = XFS_B_TO_FSB(dp->i_mount,
+ lp->valuelen = xfs_attr3_rmt_blocks(dp->i_mount,
be32_to_cpu(name_rmt->valuelen));
lp++;
}
* Each contiguous block has a header, so it is not just a simple attribute
* length to FSB conversion.
*/
-static int
+int
xfs_attr3_rmt_blocks(
struct xfs_mount *mp,
int attrlen)
{
- int buflen = XFS_ATTR3_RMT_BUF_SPACE(mp,
- mp->m_sb.sb_blocksize);
- return (attrlen + buflen - 1) / buflen;
+ if (xfs_sb_version_hascrc(&mp->m_sb)) {
+ int buflen = XFS_ATTR3_RMT_BUF_SPACE(mp, mp->m_sb.sb_blocksize);
+ return (attrlen + buflen - 1) / buflen;
+ }
+ return XFS_B_TO_FSB(mp, attrlen);
+}
+
+/*
+ * Checking of the remote attribute header is split into two parts. The verifier
+ * does CRC, location and bounds checking, the unpacking function checks the
+ * attribute parameters and owner.
+ */
+static bool
+xfs_attr3_rmt_hdr_ok(
+ struct xfs_mount *mp,
+ void *ptr,
+ xfs_ino_t ino,
+ uint32_t offset,
+ uint32_t size,
+ xfs_daddr_t bno)
+{
+ struct xfs_attr3_rmt_hdr *rmt = ptr;
+
+ if (bno != be64_to_cpu(rmt->rm_blkno))
+ return false;
+ if (offset != be32_to_cpu(rmt->rm_offset))
+ return false;
+ if (size != be32_to_cpu(rmt->rm_bytes))
+ return false;
+ if (ino != be64_to_cpu(rmt->rm_owner))
+ return false;
+
+ /* ok */
+ return true;
}
static bool
xfs_attr3_rmt_verify(
- struct xfs_buf *bp)
+ struct xfs_mount *mp,
+ void *ptr,
+ int fsbsize,
+ xfs_daddr_t bno)
{
- struct xfs_mount *mp = bp->b_target->bt_mount;
- struct xfs_attr3_rmt_hdr *rmt = bp->b_addr;
+ struct xfs_attr3_rmt_hdr *rmt = ptr;
if (!xfs_sb_version_hascrc(&mp->m_sb))
return false;
return false;
if (!uuid_equal(&rmt->rm_uuid, &mp->m_sb.sb_uuid))
return false;
- if (bp->b_bn != be64_to_cpu(rmt->rm_blkno))
+ if (be64_to_cpu(rmt->rm_blkno) != bno)
+ return false;
+ if (be32_to_cpu(rmt->rm_bytes) > fsbsize - sizeof(*rmt))
return false;
if (be32_to_cpu(rmt->rm_offset) +
be32_to_cpu(rmt->rm_bytes) >= XATTR_SIZE_MAX)
struct xfs_buf *bp)
{
struct xfs_mount *mp = bp->b_target->bt_mount;
+ char *ptr;
+ int len;
+ bool corrupt = false;
+ xfs_daddr_t bno;
/* no verification of non-crc buffers */
if (!xfs_sb_version_hascrc(&mp->m_sb))
return;
- if (!xfs_verify_cksum(bp->b_addr, BBTOB(bp->b_length),
- XFS_ATTR3_RMT_CRC_OFF) ||
- !xfs_attr3_rmt_verify(bp)) {
+ ptr = bp->b_addr;
+ bno = bp->b_bn;
+ len = BBTOB(bp->b_length);
+ ASSERT(len >= XFS_LBSIZE(mp));
+
+ while (len > 0) {
+ if (!xfs_verify_cksum(ptr, XFS_LBSIZE(mp),
+ XFS_ATTR3_RMT_CRC_OFF)) {
+ corrupt = true;
+ break;
+ }
+ if (!xfs_attr3_rmt_verify(mp, ptr, XFS_LBSIZE(mp), bno)) {
+ corrupt = true;
+ break;
+ }
+ len -= XFS_LBSIZE(mp);
+ ptr += XFS_LBSIZE(mp);
+ bno += mp->m_bsize;
+ }
+
+ if (corrupt) {
XFS_CORRUPTION_ERROR(__func__, XFS_ERRLEVEL_LOW, mp, bp->b_addr);
xfs_buf_ioerror(bp, EFSCORRUPTED);
- }
+ } else
+ ASSERT(len == 0);
}
static void
{
struct xfs_mount *mp = bp->b_target->bt_mount;
struct xfs_buf_log_item *bip = bp->b_fspriv;
+ char *ptr;
+ int len;
+ xfs_daddr_t bno;
/* no verification of non-crc buffers */
if (!xfs_sb_version_hascrc(&mp->m_sb))
return;
- if (!xfs_attr3_rmt_verify(bp)) {
- XFS_CORRUPTION_ERROR(__func__, XFS_ERRLEVEL_LOW, mp, bp->b_addr);
- xfs_buf_ioerror(bp, EFSCORRUPTED);
- return;
- }
+ ptr = bp->b_addr;
+ bno = bp->b_bn;
+ len = BBTOB(bp->b_length);
+ ASSERT(len >= XFS_LBSIZE(mp));
+
+ while (len > 0) {
+ if (!xfs_attr3_rmt_verify(mp, ptr, XFS_LBSIZE(mp), bno)) {
+ XFS_CORRUPTION_ERROR(__func__,
+ XFS_ERRLEVEL_LOW, mp, bp->b_addr);
+ xfs_buf_ioerror(bp, EFSCORRUPTED);
+ return;
+ }
+ if (bip) {
+ struct xfs_attr3_rmt_hdr *rmt;
+
+ rmt = (struct xfs_attr3_rmt_hdr *)ptr;
+ rmt->rm_lsn = cpu_to_be64(bip->bli_item.li_lsn);
+ }
+ xfs_update_cksum(ptr, XFS_LBSIZE(mp), XFS_ATTR3_RMT_CRC_OFF);
- if (bip) {
- struct xfs_attr3_rmt_hdr *rmt = bp->b_addr;
- rmt->rm_lsn = cpu_to_be64(bip->bli_item.li_lsn);
+ len -= XFS_LBSIZE(mp);
+ ptr += XFS_LBSIZE(mp);
+ bno += mp->m_bsize;
}
- xfs_update_cksum(bp->b_addr, BBTOB(bp->b_length),
- XFS_ATTR3_RMT_CRC_OFF);
+ ASSERT(len == 0);
}
const struct xfs_buf_ops xfs_attr3_rmt_buf_ops = {
.verify_write = xfs_attr3_rmt_write_verify,
};
-static int
+STATIC int
xfs_attr3_rmt_hdr_set(
struct xfs_mount *mp,
+ void *ptr,
xfs_ino_t ino,
uint32_t offset,
uint32_t size,
- struct xfs_buf *bp)
+ xfs_daddr_t bno)
{
- struct xfs_attr3_rmt_hdr *rmt = bp->b_addr;
+ struct xfs_attr3_rmt_hdr *rmt = ptr;
if (!xfs_sb_version_hascrc(&mp->m_sb))
return 0;
rmt->rm_bytes = cpu_to_be32(size);
uuid_copy(&rmt->rm_uuid, &mp->m_sb.sb_uuid);
rmt->rm_owner = cpu_to_be64(ino);
- rmt->rm_blkno = cpu_to_be64(bp->b_bn);
- bp->b_ops = &xfs_attr3_rmt_buf_ops;
+ rmt->rm_blkno = cpu_to_be64(bno);
return sizeof(struct xfs_attr3_rmt_hdr);
}
/*
- * Checking of the remote attribute header is split into two parts. the verifier
- * does CRC, location and bounds checking, the unpacking function checks the
- * attribute parameters and owner.
+ * Helper functions to copy attribute data in and out of the one disk extents
*/
-static bool
-xfs_attr3_rmt_hdr_ok(
- struct xfs_mount *mp,
- xfs_ino_t ino,
- uint32_t offset,
- uint32_t size,
- struct xfs_buf *bp)
+STATIC int
+xfs_attr_rmtval_copyout(
+ struct xfs_mount *mp,
+ struct xfs_buf *bp,
+ xfs_ino_t ino,
+ int *offset,
+ int *valuelen,
+ char **dst)
{
- struct xfs_attr3_rmt_hdr *rmt = bp->b_addr;
+ char *src = bp->b_addr;
+ xfs_daddr_t bno = bp->b_bn;
+ int len = BBTOB(bp->b_length);
- if (offset != be32_to_cpu(rmt->rm_offset))
- return false;
- if (size != be32_to_cpu(rmt->rm_bytes))
- return false;
- if (ino != be64_to_cpu(rmt->rm_owner))
- return false;
+ ASSERT(len >= XFS_LBSIZE(mp));
- /* ok */
- return true;
+ while (len > 0 && *valuelen > 0) {
+ int hdr_size = 0;
+ int byte_cnt = XFS_ATTR3_RMT_BUF_SPACE(mp, XFS_LBSIZE(mp));
+
+ byte_cnt = min_t(int, *valuelen, byte_cnt);
+
+ if (xfs_sb_version_hascrc(&mp->m_sb)) {
+ if (!xfs_attr3_rmt_hdr_ok(mp, src, ino, *offset,
+ byte_cnt, bno)) {
+ xfs_alert(mp,
+"remote attribute header mismatch bno/off/len/owner (0x%llx/0x%x/Ox%x/0x%llx)",
+ bno, *offset, byte_cnt, ino);
+ return EFSCORRUPTED;
+ }
+ hdr_size = sizeof(struct xfs_attr3_rmt_hdr);
+ }
+
+ memcpy(*dst, src + hdr_size, byte_cnt);
+
+ /* roll buffer forwards */
+ len -= XFS_LBSIZE(mp);
+ src += XFS_LBSIZE(mp);
+ bno += mp->m_bsize;
+
+ /* roll attribute data forwards */
+ *valuelen -= byte_cnt;
+ *dst += byte_cnt;
+ *offset += byte_cnt;
+ }
+ return 0;
+}
+
+STATIC void
+xfs_attr_rmtval_copyin(
+ struct xfs_mount *mp,
+ struct xfs_buf *bp,
+ xfs_ino_t ino,
+ int *offset,
+ int *valuelen,
+ char **src)
+{
+ char *dst = bp->b_addr;
+ xfs_daddr_t bno = bp->b_bn;
+ int len = BBTOB(bp->b_length);
+
+ ASSERT(len >= XFS_LBSIZE(mp));
+
+ while (len > 0 && *valuelen > 0) {
+ int hdr_size;
+ int byte_cnt = XFS_ATTR3_RMT_BUF_SPACE(mp, XFS_LBSIZE(mp));
+
+ byte_cnt = min(*valuelen, byte_cnt);
+ hdr_size = xfs_attr3_rmt_hdr_set(mp, dst, ino, *offset,
+ byte_cnt, bno);
+
+ memcpy(dst + hdr_size, *src, byte_cnt);
+
+ /*
+ * If this is the last block, zero the remainder of it.
+ * Check that we are actually the last block, too.
+ */
+ if (byte_cnt + hdr_size < XFS_LBSIZE(mp)) {
+ ASSERT(*valuelen - byte_cnt == 0);
+ ASSERT(len == XFS_LBSIZE(mp));
+ memset(dst + hdr_size + byte_cnt, 0,
+ XFS_LBSIZE(mp) - hdr_size - byte_cnt);
+ }
+
+ /* roll buffer forwards */
+ len -= XFS_LBSIZE(mp);
+ dst += XFS_LBSIZE(mp);
+ bno += mp->m_bsize;
+
+ /* roll attribute data forwards */
+ *valuelen -= byte_cnt;
+ *src += byte_cnt;
+ *offset += byte_cnt;
+ }
}
/*
struct xfs_bmbt_irec map[ATTR_RMTVALUE_MAPSIZE];
struct xfs_mount *mp = args->dp->i_mount;
struct xfs_buf *bp;
- xfs_daddr_t dblkno;
xfs_dablk_t lblkno = args->rmtblkno;
- void *dst = args->value;
+ char *dst = args->value;
int valuelen = args->valuelen;
int nmap;
int error;
- int blkcnt;
+ int blkcnt = args->rmtblkcnt;
int i;
int offset = 0;
while (valuelen > 0) {
nmap = ATTR_RMTVALUE_MAPSIZE;
error = xfs_bmapi_read(args->dp, (xfs_fileoff_t)lblkno,
- args->rmtblkcnt, map, &nmap,
+ blkcnt, map, &nmap,
XFS_BMAPI_ATTRFORK);
if (error)
return error;
ASSERT(nmap >= 1);
for (i = 0; (i < nmap) && (valuelen > 0); i++) {
- int byte_cnt;
- char *src;
+ xfs_daddr_t dblkno;
+ int dblkcnt;
ASSERT((map[i].br_startblock != DELAYSTARTBLOCK) &&
(map[i].br_startblock != HOLESTARTBLOCK));
dblkno = XFS_FSB_TO_DADDR(mp, map[i].br_startblock);
- blkcnt = XFS_FSB_TO_BB(mp, map[i].br_blockcount);
+ dblkcnt = XFS_FSB_TO_BB(mp, map[i].br_blockcount);
error = xfs_trans_read_buf(mp, NULL, mp->m_ddev_targp,
- dblkno, blkcnt, 0, &bp,
+ dblkno, dblkcnt, 0, &bp,
&xfs_attr3_rmt_buf_ops);
if (error)
return error;
- byte_cnt = min_t(int, valuelen, BBTOB(bp->b_length));
- byte_cnt = XFS_ATTR3_RMT_BUF_SPACE(mp, byte_cnt);
-
- src = bp->b_addr;
- if (xfs_sb_version_hascrc(&mp->m_sb)) {
- if (!xfs_attr3_rmt_hdr_ok(mp, args->dp->i_ino,
- offset, byte_cnt, bp)) {
- xfs_alert(mp,
-"remote attribute header does not match required off/len/owner (0x%x/Ox%x,0x%llx)",
- offset, byte_cnt, args->dp->i_ino);
- xfs_buf_relse(bp);
- return EFSCORRUPTED;
-
- }
-
- src += sizeof(struct xfs_attr3_rmt_hdr);
- }
-
- memcpy(dst, src, byte_cnt);
+ error = xfs_attr_rmtval_copyout(mp, bp, args->dp->i_ino,
+ &offset, &valuelen,
+ &dst);
xfs_buf_relse(bp);
+ if (error)
+ return error;
- offset += byte_cnt;
- dst += byte_cnt;
- valuelen -= byte_cnt;
-
+ /* roll attribute extent map forwards */
lblkno += map[i].br_blockcount;
+ blkcnt -= map[i].br_blockcount;
}
}
ASSERT(valuelen == 0);
struct xfs_inode *dp = args->dp;
struct xfs_mount *mp = dp->i_mount;
struct xfs_bmbt_irec map;
- struct xfs_buf *bp;
- xfs_daddr_t dblkno;
xfs_dablk_t lblkno;
xfs_fileoff_t lfileoff = 0;
- void *src = args->value;
+ char *src = args->value;
int blkcnt;
int valuelen;
int nmap;
int error;
- int hdrcnt = 0;
- bool crcs = xfs_sb_version_hascrc(&mp->m_sb);
int offset = 0;
trace_xfs_attr_rmtval_set(args);
* Find a "hole" in the attribute address space large enough for
* us to drop the new attribute's value into. Because CRC enable
* attributes have headers, we can't just do a straight byte to FSB
- * conversion. We calculate the worst case block count in this case
- * and we may not need that many, so we have to handle this when
- * allocating the blocks below.
+ * conversion and have to take the header space into account.
*/
- if (!crcs)
- blkcnt = XFS_B_TO_FSB(mp, args->valuelen);
- else
- blkcnt = xfs_attr3_rmt_blocks(mp, args->valuelen);
-
+ blkcnt = xfs_attr3_rmt_blocks(mp, args->valuelen);
error = xfs_bmap_first_unused(args->trans, args->dp, blkcnt, &lfileoff,
XFS_ATTR_FORK);
if (error)
return error;
- /* Start with the attribute data. We'll allocate the rest afterwards. */
- if (crcs)
- blkcnt = XFS_B_TO_FSB(mp, args->valuelen);
-
args->rmtblkno = lblkno = (xfs_dablk_t)lfileoff;
args->rmtblkcnt = blkcnt;
(map.br_startblock != HOLESTARTBLOCK));
lblkno += map.br_blockcount;
blkcnt -= map.br_blockcount;
- hdrcnt++;
-
- /*
- * If we have enough blocks for the attribute data, calculate
- * how many extra blocks we need for headers. We might run
- * through this multiple times in the case that the additional
- * headers in the blocks needed for the data fragments spills
- * into requiring more blocks. e.g. for 512 byte blocks, we'll
- * spill for another block every 9 headers we require in this
- * loop.
- */
- if (crcs && blkcnt == 0) {
- int total_len;
-
- total_len = args->valuelen +
- hdrcnt * sizeof(struct xfs_attr3_rmt_hdr);
- blkcnt = XFS_B_TO_FSB(mp, total_len);
- blkcnt -= args->rmtblkcnt;
- args->rmtblkcnt += blkcnt;
- }
/*
* Start the next trans in the chain.
* the INCOMPLETE flag.
*/
lblkno = args->rmtblkno;
+ blkcnt = args->rmtblkcnt;
valuelen = args->valuelen;
while (valuelen > 0) {
- int byte_cnt;
- char *buf;
+ struct xfs_buf *bp;
+ xfs_daddr_t dblkno;
+ int dblkcnt;
+
+ ASSERT(blkcnt > 0);
- /*
- * Try to remember where we decided to put the value.
- */
xfs_bmap_init(args->flist, args->firstblock);
nmap = 1;
error = xfs_bmapi_read(dp, (xfs_fileoff_t)lblkno,
- args->rmtblkcnt, &map, &nmap,
+ blkcnt, &map, &nmap,
XFS_BMAPI_ATTRFORK);
if (error)
return(error);
(map.br_startblock != HOLESTARTBLOCK));
dblkno = XFS_FSB_TO_DADDR(mp, map.br_startblock),
- blkcnt = XFS_FSB_TO_BB(mp, map.br_blockcount);
+ dblkcnt = XFS_FSB_TO_BB(mp, map.br_blockcount);
- bp = xfs_buf_get(mp->m_ddev_targp, dblkno, blkcnt, 0);
+ bp = xfs_buf_get(mp->m_ddev_targp, dblkno, dblkcnt, 0);
if (!bp)
return ENOMEM;
bp->b_ops = &xfs_attr3_rmt_buf_ops;
- byte_cnt = BBTOB(bp->b_length);
- byte_cnt = XFS_ATTR3_RMT_BUF_SPACE(mp, byte_cnt);
- if (valuelen < byte_cnt)
- byte_cnt = valuelen;
-
- buf = bp->b_addr;
- buf += xfs_attr3_rmt_hdr_set(mp, dp->i_ino, offset,
- byte_cnt, bp);
- memcpy(buf, src, byte_cnt);
-
- if (byte_cnt < BBTOB(bp->b_length))
- xfs_buf_zero(bp, byte_cnt,
- BBTOB(bp->b_length) - byte_cnt);
+ xfs_attr_rmtval_copyin(mp, bp, args->dp->i_ino, &offset,
+ &valuelen, &src);
error = xfs_bwrite(bp); /* GROT: NOTE: synchronous write */
xfs_buf_relse(bp);
if (error)
return error;
- src += byte_cnt;
- valuelen -= byte_cnt;
- offset += byte_cnt;
- hdrcnt--;
+ /* roll attribute extent map forwards */
lblkno += map.br_blockcount;
+ blkcnt -= map.br_blockcount;
}
ASSERT(valuelen == 0);
- ASSERT(hdrcnt == 0);
return 0;
}
* out-of-line buffer that it is stored on.
*/
int
-xfs_attr_rmtval_remove(xfs_da_args_t *args)
+xfs_attr_rmtval_remove(
+ struct xfs_da_args *args)
{
- xfs_mount_t *mp;
- xfs_bmbt_irec_t map;
- xfs_buf_t *bp;
- xfs_daddr_t dblkno;
- xfs_dablk_t lblkno;
- int valuelen, blkcnt, nmap, error, done, committed;
+ struct xfs_mount *mp = args->dp->i_mount;
+ xfs_dablk_t lblkno;
+ int blkcnt;
+ int error;
+ int done;
trace_xfs_attr_rmtval_remove(args);
- mp = args->dp->i_mount;
-
/*
- * Roll through the "value", invalidating the attribute value's
- * blocks.
+ * Roll through the "value", invalidating the attribute value's blocks.
+ * Note that args->rmtblkcnt is the minimum number of data blocks we'll
+ * see for a CRC enabled remote attribute. Each extent will have a
+ * header, and so we may have more blocks than we realise here. If we
+ * fail to map the blocks correctly, we'll have problems with the buffer
+ * lookups.
*/
lblkno = args->rmtblkno;
- valuelen = args->rmtblkcnt;
- while (valuelen > 0) {
+ blkcnt = args->rmtblkcnt;
+ while (blkcnt > 0) {
+ struct xfs_bmbt_irec map;
+ struct xfs_buf *bp;
+ xfs_daddr_t dblkno;
+ int dblkcnt;
+ int nmap;
+
/*
* Try to remember where we decided to put the value.
*/
nmap = 1;
error = xfs_bmapi_read(args->dp, (xfs_fileoff_t)lblkno,
- args->rmtblkcnt, &map, &nmap,
- XFS_BMAPI_ATTRFORK);
+ blkcnt, &map, &nmap, XFS_BMAPI_ATTRFORK);
if (error)
return(error);
ASSERT(nmap == 1);
(map.br_startblock != HOLESTARTBLOCK));
dblkno = XFS_FSB_TO_DADDR(mp, map.br_startblock),
- blkcnt = XFS_FSB_TO_BB(mp, map.br_blockcount);
+ dblkcnt = XFS_FSB_TO_BB(mp, map.br_blockcount);
/*
* If the "remote" value is in the cache, remove it.
*/
- bp = xfs_incore(mp->m_ddev_targp, dblkno, blkcnt, XBF_TRYLOCK);
+ bp = xfs_incore(mp->m_ddev_targp, dblkno, dblkcnt, XBF_TRYLOCK);
if (bp) {
xfs_buf_stale(bp);
xfs_buf_relse(bp);
bp = NULL;
}
- valuelen -= map.br_blockcount;
-
lblkno += map.br_blockcount;
+ blkcnt -= map.br_blockcount;
}
/*
blkcnt = args->rmtblkcnt;
done = 0;
while (!done) {
+ int committed;
+
xfs_bmap_init(args->flist, args->firstblock);
error = xfs_bunmapi(args->trans, args->dp, lblkno, blkcnt,
XFS_BMAPI_ATTRFORK | XFS_BMAPI_METADATA,
#define XFS_ATTR3_RMT_MAGIC 0x5841524d /* XARM */
+/*
+ * There is one of these headers per filesystem block in a remote attribute.
+ * This is done to ensure there is a 1:1 mapping between the attribute value
+ * length and the number of blocks needed to store the attribute. This makes the
+ * verification of a buffer a little more complex, but greatly simplifies the
+ * allocation, reading and writing of these attributes as we don't have to guess
+ * the number of blocks needed to store the attribute data.
+ */
struct xfs_attr3_rmt_hdr {
__be32 rm_magic;
__be32 rm_offset;
extern const struct xfs_buf_ops xfs_attr3_rmt_buf_ops;
+int xfs_attr3_rmt_blocks(struct xfs_mount *mp, int attrlen);
+
int xfs_attr_rmtval_get(struct xfs_da_args *args);
int xfs_attr_rmtval_set(struct xfs_da_args *args);
int xfs_attr_rmtval_remove(struct xfs_da_args *args);
xfs_alert(btp->bt_mount,
"%s: Block out of range: block 0x%llx, EOFS 0x%llx ",
__func__, blkno, eofs);
+ WARN_ON(1);
return NULL;
}
{
xfs_buftarg_t *btp;
- btp = kmem_zalloc(sizeof(*btp), KM_SLEEP);
+ btp = kmem_zalloc(sizeof(*btp), KM_SLEEP | KM_NOFS);
btp->bt_mount = mp;
btp->bt_dev = bdev->bd_dev;
vecp->i_addr = xfs_buf_offset(bp, buffer_offset);
vecp->i_len = nbits * XFS_BLF_CHUNK;
vecp->i_type = XLOG_REG_TYPE_BCHUNK;
-/*
- * You would think we need to bump the nvecs here too, but we do not
- * this number is used by recovery, and it gets confused by the boundary
- * split here
- * nvecs++;
- */
+ nvecs++;
vecp++;
first_bit = next_bit;
last_bit = next_bit;
break;
return;
case XFS_ATTR_LEAF_MAGIC:
+ case XFS_ATTR3_LEAF_MAGIC:
bp->b_ops = &xfs_attr3_leaf_buf_ops;
bp->b_ops->verify_read(bp);
return;
ASSERT(nirecs >= 1);
if (nirecs > 1) {
- map = kmem_zalloc(nirecs * sizeof(struct xfs_buf_map), KM_SLEEP);
+ map = kmem_zalloc(nirecs * sizeof(struct xfs_buf_map),
+ KM_SLEEP | KM_NOFS);
if (!map)
return ENOMEM;
*mapp = map;
* Optimize the one-block case.
*/
if (nfsb != 1)
- irecs = kmem_zalloc(sizeof(irec) * nfsb, KM_SLEEP);
+ irecs = kmem_zalloc(sizeof(irec) * nfsb,
+ KM_SLEEP | KM_NOFS);
nirecs = nfsb;
error = xfs_bmapi_read(dp, (xfs_fileoff_t)bno, nfsb, irecs,
int taforkblks = 0;
__uint64_t tmp;
+ /*
+ * We have no way of updating owner information in the BMBT blocks for
+ * each inode on CRC enabled filesystems, so to avoid corrupting the
+ * this metadata we simply don't allow extent swaps to occur.
+ */
+ if (xfs_sb_version_hascrc(&mp->m_sb))
+ return XFS_ERROR(EINVAL);
+
tempifp = kmem_alloc(sizeof(xfs_ifork_t), KM_MAYFAIL);
if (!tempifp) {
error = XFS_ERROR(ENOMEM);
__be32 firstdb; /* db of first entry */
__be32 nvalid; /* count of valid entries */
__be32 nused; /* count of used entries */
+ __be32 pad; /* 64 bit alignment. */
};
struct xfs_dir3_free {
mp->m_sb.sb_blocksize);
map_info = kmem_zalloc(offsetof(struct xfs_dir2_leaf_map_info, map) +
(length * sizeof(struct xfs_bmbt_irec)),
- KM_SLEEP);
+ KM_SLEEP | KM_NOFS);
map_info->map_size = length;
/*
* Initialize the new block to be empty, and remember
* its first slot as our empty slot.
*/
- hdr.magic = XFS_DIR2_FREE_MAGIC;
- hdr.firstdb = 0;
- hdr.nused = 0;
- hdr.nvalid = 0;
+ memset(bp->b_addr, 0, sizeof(struct xfs_dir3_free_hdr));
+ memset(&hdr, 0, sizeof(hdr));
+
if (xfs_sb_version_hascrc(&mp->m_sb)) {
struct xfs_dir3_free_hdr *hdr3 = bp->b_addr;
hdr.magic = XFS_DIR3_FREE_MAGIC;
+
hdr3->hdr.blkno = cpu_to_be64(bp->b_bn);
hdr3->hdr.owner = cpu_to_be64(dp->i_ino);
uuid_copy(&hdr3->hdr.uuid, &mp->m_sb.sb_uuid);
- }
+ } else
+ hdr.magic = XFS_DIR2_FREE_MAGIC;
xfs_dir3_free_hdr_to_disk(bp->b_addr, &hdr);
*bpp = bp;
return 0;
*/
freehdr.firstdb = (fbno - XFS_DIR2_FREE_FIRSTDB(mp)) *
xfs_dir3_free_max_bests(mp);
- free->hdr.nvalid = 0;
- free->hdr.nused = 0;
} else {
free = fbp->b_addr;
bests = xfs_dir3_free_bests_p(mp, free);
d->dd_diskdq.d_version = XFS_DQUOT_VERSION;
d->dd_diskdq.d_id = cpu_to_be32(curid);
d->dd_diskdq.d_flags = type;
- if (xfs_sb_version_hascrc(&mp->m_sb))
+ if (xfs_sb_version_hascrc(&mp->m_sb)) {
uuid_copy(&d->dd_uuid, &mp->m_sb.sb_uuid);
+ xfs_update_cksum((char *)d, sizeof(struct xfs_dqblk),
+ XFS_DQUOT_CRC_OFF);
+ }
}
xfs_trans_dquot_buf(tp, bp,
dqp->q_low_space[XFS_QLOWSP_5_PCNT] = space * 5;
}
-STATIC void
-xfs_dquot_buf_calc_crc(
- struct xfs_mount *mp,
- struct xfs_buf *bp)
-{
- struct xfs_dqblk *d = (struct xfs_dqblk *)bp->b_addr;
- int i;
-
- if (!xfs_sb_version_hascrc(&mp->m_sb))
- return;
-
- for (i = 0; i < mp->m_quotainfo->qi_dqperchunk; i++, d++) {
- xfs_update_cksum((char *)d, sizeof(struct xfs_dqblk),
- offsetof(struct xfs_dqblk, dd_crc));
- }
-}
-
STATIC bool
xfs_dquot_buf_verify_crc(
struct xfs_mount *mp,
for (i = 0; i < ndquots; i++, d++) {
if (!xfs_verify_cksum((char *)d, sizeof(struct xfs_dqblk),
- offsetof(struct xfs_dqblk, dd_crc)))
+ XFS_DQUOT_CRC_OFF))
return false;
if (!uuid_equal(&d->dd_uuid, &mp->m_sb.sb_uuid))
return false;
}
-
return true;
}
}
}
+/*
+ * we don't calculate the CRC here as that is done when the dquot is flushed to
+ * the buffer after the update is done. This ensures that the dquot in the
+ * buffer always has an up-to-date CRC value.
+ */
void
xfs_dquot_buf_write_verify(
struct xfs_buf *bp)
xfs_buf_ioerror(bp, EFSCORRUPTED);
return;
}
- xfs_dquot_buf_calc_crc(mp, bp);
}
const struct xfs_buf_ops xfs_dquot_buf_ops = {
* copy the lsn into the on-disk dquot now while we have the in memory
* dquot here. This can't be done later in the write verifier as we
* can't get access to the log item at that point in time.
+ *
+ * We also calculate the CRC here so that the on-disk dquot in the
+ * buffer always has a valid CRC. This ensures there is no possibility
+ * of a dquot without an up-to-date CRC getting to disk.
*/
if (xfs_sb_version_hascrc(&mp->m_sb)) {
struct xfs_dqblk *dqb = (struct xfs_dqblk *)ddqp;
dqb->dd_lsn = cpu_to_be64(dqp->q_logitem.qli_item.li_lsn);
+ xfs_update_cksum((char *)dqb, sizeof(struct xfs_dqblk),
+ XFS_DQUOT_CRC_OFF);
}
/*
{
ASSERT(atomic_read(&efip->efi_next_extent) >= nextents);
if (atomic_sub_and_test(nextents, &efip->efi_next_extent)) {
- __xfs_efi_release(efip);
-
/* recovery needs us to drop the EFI reference, too */
if (test_bit(XFS_EFI_RECOVERED, &efip->efi_flags))
__xfs_efi_release(efip);
+
+ __xfs_efi_release(efip);
+ /* efip may now have been freed, do not reference it again. */
}
}
#define XFS_FSOP_GEOM_FLAGS_PROJID32 0x0800 /* 32-bit project IDs */
#define XFS_FSOP_GEOM_FLAGS_DIRV2CI 0x1000 /* ASCII only CI names */
#define XFS_FSOP_GEOM_FLAGS_LAZYSB 0x4000 /* lazy superblock counters */
+#define XFS_FSOP_GEOM_FLAGS_V5SB 0x8000 /* version 5 superblock */
/*
(xfs_sb_version_hasattr2(&mp->m_sb) ?
XFS_FSOP_GEOM_FLAGS_ATTR2 : 0) |
(xfs_sb_version_hasprojid32bit(&mp->m_sb) ?
- XFS_FSOP_GEOM_FLAGS_PROJID32 : 0);
+ XFS_FSOP_GEOM_FLAGS_PROJID32 : 0) |
+ (xfs_sb_version_hascrc(&mp->m_sb) ?
+ XFS_FSOP_GEOM_FLAGS_V5SB : 0);
geo->logsectsize = xfs_sb_version_hassector(&mp->m_sb) ?
mp->m_sb.sb_logsectsize : BBSIZE;
geo->rtsectsize = mp->m_sb.sb_blocksize;
dip->di_next_unlinked = agi->agi_unlinked[bucket_index];
offset = ip->i_imap.im_boffset +
offsetof(xfs_dinode_t, di_next_unlinked);
+
+ /* need to recalc the inode CRC if appropriate */
+ xfs_dinode_calc_crc(mp, dip);
+
xfs_trans_inode_buf(tp, ibp);
xfs_trans_log_buf(tp, ibp, offset,
(offset + sizeof(xfs_agino_t) - 1));
dip->di_next_unlinked = cpu_to_be32(NULLAGINO);
offset = ip->i_imap.im_boffset +
offsetof(xfs_dinode_t, di_next_unlinked);
+
+ /* need to recalc the inode CRC if appropriate */
+ xfs_dinode_calc_crc(mp, dip);
+
xfs_trans_inode_buf(tp, ibp);
xfs_trans_log_buf(tp, ibp, offset,
(offset + sizeof(xfs_agino_t) - 1));
dip->di_next_unlinked = cpu_to_be32(NULLAGINO);
offset = ip->i_imap.im_boffset +
offsetof(xfs_dinode_t, di_next_unlinked);
+
+ /* need to recalc the inode CRC if appropriate */
+ xfs_dinode_calc_crc(mp, dip);
+
xfs_trans_inode_buf(tp, ibp);
xfs_trans_log_buf(tp, ibp, offset,
(offset + sizeof(xfs_agino_t) - 1));
last_dip->di_next_unlinked = cpu_to_be32(next_agino);
ASSERT(next_agino != 0);
offset = last_offset + offsetof(xfs_dinode_t, di_next_unlinked);
+
+ /* need to recalc the inode CRC if appropriate */
+ xfs_dinode_calc_crc(mp, last_dip);
+
xfs_trans_inode_buf(tp, last_ibp);
xfs_trans_log_buf(tp, last_ibp, offset,
(offset + sizeof(xfs_agino_t) - 1));
return 0;
}
+static void
+xfs_setattr_mode(
+ struct xfs_trans *tp,
+ struct xfs_inode *ip,
+ struct iattr *iattr)
+{
+ struct inode *inode = VFS_I(ip);
+ umode_t mode = iattr->ia_mode;
+
+ ASSERT(tp);
+ ASSERT(xfs_isilocked(ip, XFS_ILOCK_EXCL));
+
+ if (!in_group_p(inode->i_gid) && !capable(CAP_FSETID))
+ mode &= ~S_ISGID;
+
+ ip->i_d.di_mode &= S_IFMT;
+ ip->i_d.di_mode |= mode & ~S_IFMT;
+
+ inode->i_mode &= S_IFMT;
+ inode->i_mode |= mode & ~S_IFMT;
+}
+
int
xfs_setattr_nonsize(
struct xfs_inode *ip,
/*
* Change file access modes.
*/
- if (mask & ATTR_MODE) {
- umode_t mode = iattr->ia_mode;
-
- if (!in_group_p(inode->i_gid) && !capable(CAP_FSETID))
- mode &= ~S_ISGID;
-
- ip->i_d.di_mode &= S_IFMT;
- ip->i_d.di_mode |= mode & ~S_IFMT;
-
- inode->i_mode &= S_IFMT;
- inode->i_mode |= mode & ~S_IFMT;
- }
+ if (mask & ATTR_MODE)
+ xfs_setattr_mode(tp, ip, iattr);
/*
* Change file access or modified times.
return XFS_ERROR(error);
ASSERT(S_ISREG(ip->i_d.di_mode));
- ASSERT((mask & (ATTR_MODE|ATTR_UID|ATTR_GID|ATTR_ATIME|ATTR_ATIME_SET|
- ATTR_MTIME_SET|ATTR_KILL_SUID|ATTR_KILL_SGID|
- ATTR_KILL_PRIV|ATTR_TIMES_SET)) == 0);
+ ASSERT((mask & (ATTR_UID|ATTR_GID|ATTR_ATIME|ATTR_ATIME_SET|
+ ATTR_MTIME_SET|ATTR_KILL_PRIV|ATTR_TIMES_SET)) == 0);
if (!(flags & XFS_ATTR_NOLOCK)) {
lock_flags |= XFS_IOLOCK_EXCL;
xfs_inode_clear_eofblocks_tag(ip);
}
+ /*
+ * Change file access modes.
+ */
+ if (mask & ATTR_MODE)
+ xfs_setattr_mode(tp, ip, iattr);
+
if (mask & ATTR_CTIME) {
inode->i_ctime = iattr->ia_ctime;
ip->i_d.di_ctime.t_sec = iattr->ia_ctime.tv_sec;
new_lv = kmem_zalloc(sizeof(*new_lv) +
niovecs * sizeof(struct xfs_log_iovec),
- KM_SLEEP);
+ KM_SLEEP|KM_NOFS);
/* The allocated iovec region lies beyond the log vector. */
new_lv->lv_iovecp = (struct xfs_log_iovec *)&new_lv[1];
}
/*
- * Sort the log items in the transaction. Cancelled buffers need
- * to be put first so they are processed before any items that might
- * modify the buffers. If they are cancelled, then the modifications
- * don't need to be replayed.
+ * Sort the log items in the transaction.
+ *
+ * The ordering constraints are defined by the inode allocation and unlink
+ * behaviour. The rules are:
+ *
+ * 1. Every item is only logged once in a given transaction. Hence it
+ * represents the last logged state of the item. Hence ordering is
+ * dependent on the order in which operations need to be performed so
+ * required initial conditions are always met.
+ *
+ * 2. Cancelled buffers are recorded in pass 1 in a separate table and
+ * there's nothing to replay from them so we can simply cull them
+ * from the transaction. However, we can't do that until after we've
+ * replayed all the other items because they may be dependent on the
+ * cancelled buffer and replaying the cancelled buffer can remove it
+ * form the cancelled buffer table. Hence they have tobe done last.
+ *
+ * 3. Inode allocation buffers must be replayed before inode items that
+ * read the buffer and replay changes into it.
+ *
+ * 4. Inode unlink buffers must be replayed after inode items are replayed.
+ * This ensures that inodes are completely flushed to the inode buffer
+ * in a "free" state before we remove the unlinked inode list pointer.
+ *
+ * Hence the ordering needs to be inode allocation buffers first, inode items
+ * second, inode unlink buffers third and cancelled buffers last.
+ *
+ * But there's a problem with that - we can't tell an inode allocation buffer
+ * apart from a regular buffer, so we can't separate them. We can, however,
+ * tell an inode unlink buffer from the others, and so we can separate them out
+ * from all the other buffers and move them to last.
+ *
+ * Hence, 4 lists, in order from head to tail:
+ * - buffer_list for all buffers except cancelled/inode unlink buffers
+ * - item_list for all non-buffer items
+ * - inode_buffer_list for inode unlink buffers
+ * - cancel_list for the cancelled buffers
*/
STATIC int
xlog_recover_reorder_trans(
{
xlog_recover_item_t *item, *n;
LIST_HEAD(sort_list);
+ LIST_HEAD(cancel_list);
+ LIST_HEAD(buffer_list);
+ LIST_HEAD(inode_buffer_list);
+ LIST_HEAD(inode_list);
list_splice_init(&trans->r_itemq, &sort_list);
list_for_each_entry_safe(item, n, &sort_list, ri_list) {
switch (ITEM_TYPE(item)) {
case XFS_LI_BUF:
- if (!(buf_f->blf_flags & XFS_BLF_CANCEL)) {
+ if (buf_f->blf_flags & XFS_BLF_CANCEL) {
trace_xfs_log_recover_item_reorder_head(log,
trans, item, pass);
- list_move(&item->ri_list, &trans->r_itemq);
+ list_move(&item->ri_list, &cancel_list);
break;
}
+ if (buf_f->blf_flags & XFS_BLF_INODE_BUF) {
+ list_move(&item->ri_list, &inode_buffer_list);
+ break;
+ }
+ list_move_tail(&item->ri_list, &buffer_list);
+ break;
case XFS_LI_INODE:
case XFS_LI_DQUOT:
case XFS_LI_QUOTAOFF:
case XFS_LI_EFI:
trace_xfs_log_recover_item_reorder_tail(log,
trans, item, pass);
- list_move_tail(&item->ri_list, &trans->r_itemq);
+ list_move_tail(&item->ri_list, &inode_list);
break;
default:
xfs_warn(log->l_mp,
}
}
ASSERT(list_empty(&sort_list));
+ if (!list_empty(&buffer_list))
+ list_splice(&buffer_list, &trans->r_itemq);
+ if (!list_empty(&inode_list))
+ list_splice_tail(&inode_list, &trans->r_itemq);
+ if (!list_empty(&inode_buffer_list))
+ list_splice_tail(&inode_buffer_list, &trans->r_itemq);
+ if (!list_empty(&cancel_list))
+ list_splice_tail(&cancel_list, &trans->r_itemq);
return 0;
}
buffer_nextp = (xfs_agino_t *)xfs_buf_offset(bp,
next_unlinked_offset);
*buffer_nextp = *logged_nextp;
+
+ /*
+ * If necessary, recalculate the CRC in the on-disk inode. We
+ * have to leave the inode in a consistent state for whoever
+ * reads it next....
+ */
+ xfs_dinode_calc_crc(mp, (struct xfs_dinode *)
+ xfs_buf_offset(bp, i * mp->m_sb.sb_inodesize));
+
}
return 0;
ASSERT(BBTOB(bp->b_io_length) >=
((uint)bit << XFS_BLF_SHIFT) + (nbits << XFS_BLF_SHIFT));
+ /*
+ * The dirty regions logged in the buffer, even though
+ * contiguous, may span multiple chunks. This is because the
+ * dirty region may span a physical page boundary in a buffer
+ * and hence be split into two separate vectors for writing into
+ * the log. Hence we need to trim nbits back to the length of
+ * the current region being copied out of the log.
+ */
+ if (item->ri_buf[i].i_len < (nbits << XFS_BLF_SHIFT))
+ nbits = item->ri_buf[i].i_len >> XFS_BLF_SHIFT;
+
/*
* Do a sanity check if this is a dquot buffer. Just checking
* the first dquot in the buffer should do. XXXThis is
d->dd_diskdq.d_flags = type;
d->dd_diskdq.d_id = cpu_to_be32(id);
+ if (xfs_sb_version_hascrc(&mp->m_sb)) {
+ uuid_copy(&d->dd_uuid, &mp->m_sb.sb_uuid);
+ xfs_update_cksum((char *)d, sizeof(struct xfs_dqblk),
+ XFS_DQUOT_CRC_OFF);
+ }
+
return errs;
}
}
memcpy(ddq, recddq, item->ri_buf[1].i_len);
+ if (xfs_sb_version_hascrc(&mp->m_sb)) {
+ xfs_update_cksum((char *)ddq, sizeof(struct xfs_dqblk),
+ XFS_DQUOT_CRC_OFF);
+ }
ASSERT(dq_f->qlf_size == 2);
ASSERT(bp->b_target->bt_mount == mp);
#include "xfs_qm.h"
#include "xfs_trace.h"
#include "xfs_icache.h"
+#include "xfs_cksum.h"
/*
* The global quota manager. There is only one of these for the entire
xfs_dqid_t id,
uint type)
{
- xfs_disk_dquot_t *ddq;
+ struct xfs_dqblk *dqb;
int j;
trace_xfs_reset_dqcounts(bp, _RET_IP_);
do_div(j, sizeof(xfs_dqblk_t));
ASSERT(mp->m_quotainfo->qi_dqperchunk == j);
#endif
- ddq = bp->b_addr;
+ dqb = bp->b_addr;
for (j = 0; j < mp->m_quotainfo->qi_dqperchunk; j++) {
+ struct xfs_disk_dquot *ddq;
+
+ ddq = (struct xfs_disk_dquot *)&dqb[j];
+
/*
* Do a sanity check, and if needed, repair the dqblk. Don't
* output any warnings because it's perfectly possible to
ddq->d_bwarns = 0;
ddq->d_iwarns = 0;
ddq->d_rtbwarns = 0;
- ddq = (xfs_disk_dquot_t *) ((xfs_dqblk_t *)ddq + 1);
+
+ if (xfs_sb_version_hascrc(&mp->m_sb)) {
+ xfs_update_cksum((char *)&dqb[j],
+ sizeof(struct xfs_dqblk),
+ XFS_DQUOT_CRC_OFF);
+ }
}
}
XFS_FSB_TO_DADDR(mp, bno),
mp->m_quotainfo->qi_dqchunklen, 0, &bp,
&xfs_dquot_buf_ops);
- if (error)
- break;
/*
- * XXX(hch): need to figure out if it makes sense to validate
- * the CRC here.
+ * CRC and validation errors will return a EFSCORRUPTED here. If
+ * this occurs, re-read without CRC validation so that we can
+ * repair the damage via xfs_qm_reset_dqcounts(). This process
+ * will leave a trace in the log indicating corruption has
+ * been detected.
*/
+ if (error == EFSCORRUPTED) {
+ error = xfs_trans_read_buf(mp, NULL, mp->m_ddev_targp,
+ XFS_FSB_TO_DADDR(mp, bno),
+ mp->m_quotainfo->qi_dqchunklen, 0, &bp,
+ NULL);
+ }
+
+ if (error)
+ break;
+
xfs_qm_reset_dqcounts(mp, bp, firstid, type);
xfs_buf_delwri_queue(bp, buffer_list);
xfs_buf_relse(bp);
- /*
- * goto the next block.
- */
+
+ /* goto the next block. */
bno++;
firstid += mp->m_quotainfo->qi_dqperchunk;
}
if ((newlim->d_fieldmask & XFS_DQ_MASK) == 0)
return 0;
- tp = xfs_trans_alloc(mp, XFS_TRANS_QM_SETQLIM);
- error = xfs_trans_reserve(tp, 0, XFS_QM_SETQLIM_LOG_RES(mp),
- 0, 0, XFS_DEFAULT_LOG_COUNT);
- if (error) {
- xfs_trans_cancel(tp, 0);
- return (error);
- }
-
/*
* We don't want to race with a quotaoff so take the quotaoff lock.
- * (We don't hold an inode lock, so there's nothing else to stop
- * a quotaoff from happening). (XXXThis doesn't currently happen
- * because we take the vfslock before calling xfs_qm_sysent).
+ * We don't hold an inode lock, so there's nothing else to stop
+ * a quotaoff from happening.
*/
mutex_lock(&q->qi_quotaofflock);
/*
- * Get the dquot (locked), and join it to the transaction.
- * Allocate the dquot if this doesn't exist.
+ * Get the dquot (locked) before we start, as we need to do a
+ * transaction to allocate it if it doesn't exist. Once we have the
+ * dquot, unlock it so we can start the next transaction safely. We hold
+ * a reference to the dquot, so it's safe to do this unlock/lock without
+ * it being reclaimed in the mean time.
*/
- if ((error = xfs_qm_dqget(mp, NULL, id, type, XFS_QMOPT_DQALLOC, &dqp))) {
- xfs_trans_cancel(tp, XFS_TRANS_ABORT);
+ error = xfs_qm_dqget(mp, NULL, id, type, XFS_QMOPT_DQALLOC, &dqp);
+ if (error) {
ASSERT(error != ENOENT);
goto out_unlock;
}
+ xfs_dqunlock(dqp);
+
+ tp = xfs_trans_alloc(mp, XFS_TRANS_QM_SETQLIM);
+ error = xfs_trans_reserve(tp, 0, XFS_QM_SETQLIM_LOG_RES(mp),
+ 0, 0, XFS_DEFAULT_LOG_COUNT);
+ if (error) {
+ xfs_trans_cancel(tp, 0);
+ goto out_rele;
+ }
+
+ xfs_dqlock(dqp);
xfs_trans_dqjoin(tp, dqp);
ddq = &dqp->q_core;
xfs_trans_log_dquot(tp, dqp);
error = xfs_trans_commit(tp, 0);
- xfs_qm_dqrele(dqp);
- out_unlock:
+out_rele:
+ xfs_qm_dqrele(dqp);
+out_unlock:
mutex_unlock(&q->qi_quotaofflock);
return error;
}
uuid_t dd_uuid; /* location information */
} xfs_dqblk_t;
+#define XFS_DQUOT_CRC_OFF offsetof(struct xfs_dqblk, dd_crc)
+
/*
* flags for q_flags field in the dquot.
*/
}
}
+ /*
+ * V5 filesystems always use attr2 format for attributes.
+ */
+ if (xfs_sb_version_hascrc(&mp->m_sb) &&
+ (mp->m_flags & XFS_MOUNT_NOATTR2)) {
+ xfs_warn(mp,
+"Cannot mount a V5 filesystem as %s. %s is always enabled for V5 filesystems.",
+ MNTOPT_NOATTR2, MNTOPT_ATTR2);
+ return XFS_ERROR(EINVAL);
+ }
+
/*
* mkfs'ed attr2 will turn on attr2 mount unless explicitly
* told by noattr2 to turn it off
struct xfs_mount *mp,
int pathlen)
{
- int fsblocks = 0;
- int len = pathlen;
+ int buflen = XFS_SYMLINK_BUF_SPACE(mp, mp->m_sb.sb_blocksize);
- do {
- fsblocks++;
- len -= XFS_SYMLINK_BUF_SPACE(mp, mp->m_sb.sb_blocksize);
- } while (len > 0);
-
- ASSERT(fsblocks <= XFS_SYMLINK_MAPS);
- return fsblocks;
+ return (pathlen + buflen - 1) / buflen;
}
static int
if (pathlen <= XFS_LITINO(mp, dp->i_d.di_version))
fs_blocks = 0;
else
- fs_blocks = XFS_B_TO_FSB(mp, pathlen);
+ fs_blocks = xfs_symlink_blocks(mp, pathlen);
resblks = XFS_SYMLINK_SPACE_RES(mp, link_name->len, fs_blocks);
error = xfs_trans_reserve(tp, resblks, XFS_SYMLINK_LOG_RES(mp), 0,
XFS_TRANS_PERM_LOG_RES, XFS_SYMLINK_LOG_COUNT);
cur_chunk = target_path;
offset = 0;
for (n = 0; n < nmaps; n++) {
- char *buf;
+ char *buf;
d = XFS_FSB_TO_DADDR(mp, mval[n].br_startblock);
byte_cnt = XFS_FSB_TO_B(mp, mval[n].br_blockcount);
bp->b_ops = &xfs_symlink_buf_ops;
byte_cnt = XFS_SYMLINK_BUF_SPACE(mp, byte_cnt);
- if (pathlen < byte_cnt) {
- byte_cnt = pathlen;
- }
+ byte_cnt = min(byte_cnt, pathlen);
buf = bp->b_addr;
buf += xfs_symlink_hdr_set(mp, ip->i_ino, offset,
xfs_trans_log_buf(tp, bp, 0, (buf + byte_cnt - 1) -
(char *)bp->b_addr);
}
+ ASSERT(pathlen == 0);
}
/*
xfs_mount_t *mp;
int nimap;
uint resblks;
- uint rounding;
+ xfs_off_t rounding;
int rt;
xfs_fileoff_t startoffset_fsb;
xfs_trans_t *tp;
inode_dio_wait(VFS_I(ip));
}
- rounding = max_t(uint, 1 << mp->m_sb.sb_blocklog, PAGE_CACHE_SIZE);
+ rounding = max_t(xfs_off_t, 1 << mp->m_sb.sb_blocklog, PAGE_CACHE_SIZE);
ioffset = offset & ~(rounding - 1);
error = -filemap_write_and_wait_range(VFS_I(ip)->i_mapping,
ioffset, -1);
unsigned long long *sta);
int acpi_bus_get_status(struct acpi_device *device);
-#ifdef CONFIG_PM
int acpi_bus_set_power(acpi_handle handle, int state);
const char *acpi_power_state_string(int state);
int acpi_device_get_power(struct acpi_device *device, int *state);
int acpi_bus_init_power(struct acpi_device *device);
int acpi_bus_update_power(acpi_handle handle, int *state_p);
bool acpi_bus_power_manageable(acpi_handle handle);
+
+#ifdef CONFIG_PM
bool acpi_bus_can_wakeup(acpi_handle handle);
-#else /* !CONFIG_PM */
-static inline int acpi_bus_set_power(acpi_handle handle, int state)
-{
- return 0;
-}
-static inline const char *acpi_power_state_string(int state)
-{
- return "D0";
-}
-static inline int acpi_device_get_power(struct acpi_device *device, int *state)
-{
- return 0;
-}
-static inline int acpi_device_set_power(struct acpi_device *device, int state)
-{
- return 0;
-}
-static inline int acpi_bus_init_power(struct acpi_device *device)
-{
- return 0;
-}
-static inline int acpi_bus_update_power(acpi_handle handle, int *state_p)
-{
- return 0;
-}
-static inline bool acpi_bus_power_manageable(acpi_handle handle)
-{
- return false;
-}
-static inline bool acpi_bus_can_wakeup(acpi_handle handle)
-{
- return false;
-}
-#endif /* !CONFIG_PM */
+#else
+static inline bool acpi_bus_can_wakeup(acpi_handle handle) { return false; }
+#endif
#ifdef CONFIG_ACPI_PROC_EVENT
int acpi_bus_generate_proc_event(struct acpi_device *device, u8 type, int data);
#endif /* CONFIG_GENERIC_IOMAP */
#endif /* CONFIG_HAS_IOPORT */
+#ifndef xlate_dev_kmem_ptr
#define xlate_dev_kmem_ptr(p) p
+#endif
+#ifndef xlate_dev_mem_ptr
#define xlate_dev_mem_ptr(p) __va(p)
+#endif
#ifdef CONFIG_VIRT_TO_BUS
#ifndef virt_to_bus
unsigned long start;
unsigned long end;
unsigned int need_flush : 1, /* Did free PTEs */
- fast_mode : 1; /* No batching */
-
/* we are in the middle of an operation to clear
* a full mm and can make some optimizations */
- unsigned int fullmm : 1,
+ fullmm : 1,
/* we have performed an operation which
* requires a complete flush of the tlb */
need_flush_all : 1;
#define HAVE_GENERIC_MMU_GATHER
-static inline int tlb_fast_mode(struct mmu_gather *tlb)
-{
-#ifdef CONFIG_SMP
- return tlb->fast_mode;
-#else
- /*
- * For UP we don't need to worry about TLB flush
- * and page free order so much..
- */
- return 1;
-#endif
-}
-
void tlb_gather_mmu(struct mmu_gather *tlb, struct mm_struct *mm, bool fullmm);
void tlb_flush_mmu(struct mmu_gather *tlb);
void tlb_finish_mmu(struct mmu_gather *tlb, unsigned long start,
* @dev: struct device of this controller
* @acpi_dma_xlate: callback function to find a suitable channel
* @data: private data used by a callback function
+ * @base_request_line: first supported request line (CSRT)
+ * @end_request_line: last supported request line (CSRT)
*/
struct acpi_dma {
struct list_head dma_controllers;
struct dma_chan *(*acpi_dma_xlate)
(struct acpi_dma_spec *, struct acpi_dma *);
void *data;
+ unsigned short base_request_line;
+ unsigned short end_request_line;
};
/* Used with acpi_dma_simple_xlate() */
}
#endif
-extern void cper_print_aer(const char *prefix, struct pci_dev *dev,
+extern void cper_print_aer(struct pci_dev *dev,
int cper_severity, struct aer_capability_regs *aer);
extern int cper_severity_to_aer(int cper_severity);
extern void aer_recover_queue(int domain, unsigned int bus, unsigned int devfn,
- int severity);
+ int severity,
+ struct aer_capability_regs *aer_regs);
#endif //_AER_H_
#define BCMA_CORE_I2S 0x834
#define BCMA_CORE_SDR_DDR1_MEM_CTL 0x835 /* SDR/DDR1 memory controller core */
#define BCMA_CORE_SHIM 0x837 /* SHIM component in ubus/6362 */
-#define BCMA_CORE_ARM_CR4 0x83e
+#define BCMA_CORE_PHY_AC 0x83B
+#define BCMA_CORE_PCIE2 0x83C /* PCI Express Gen2 */
+#define BCMA_CORE_USB30_DEV 0x83D
+#define BCMA_CORE_ARM_CR4 0x83E
#define BCMA_CORE_DEFAULT 0xFFF
#define BCMA_MAX_NR_CORES 16
+#ifndef _LINUX_BRCMPHY_H
+#define _LINUX_BRCMPHY_H
+
#define PHY_ID_BCM50610 0x0143bd60
#define PHY_ID_BCM50610M 0x0143bd70
#define PHY_ID_BCM5241 0x0143bc30
#define PHY_BRCM_CLEAR_RGMII_MODE 0x00004000
#define PHY_BRCM_DIS_TXCRXC_NOENRGY 0x00008000
#define PHY_BCM_FLAGS_VALID 0x80000000
+
+#endif /* _LINUX_BRCMPHY_H */
*
* If a subsystem synchronizes against the parent in its ->css_online() and
* before starting iterating, and synchronizes against @pos on each
- * iteration, any descendant cgroup which finished ->css_offline() is
+ * iteration, any descendant cgroup which finished ->css_online() is
* guaranteed to be visible in the future iterations.
*
* In other words, the following guarantees that a descendant can't escape
extern __printf(2, 3)
int __trace_printk(unsigned long ip, const char *fmt, ...);
+extern int __trace_bputs(unsigned long ip, const char *str);
+extern int __trace_puts(unsigned long ip, const char *str, int size);
+
/**
* trace_puts - write a string into the ftrace buffer
* @str: the string to record
* (1 when __trace_bputs is used, strlen(str) when __trace_puts is used)
*/
-extern int __trace_bputs(unsigned long ip, const char *str);
-extern int __trace_puts(unsigned long ip, const char *str, int size);
#define trace_puts(str) ({ \
static const char *trace_printk_fmt \
__attribute__((section("__trace_printk_fmt"))) = \
#define list_first_entry(ptr, type, member) \
list_entry((ptr)->next, type, member)
+/**
+ * list_first_entry_or_null - get the first element from a list
+ * @ptr: the list head to take the element from.
+ * @type: the type of the struct this is embedded in.
+ * @member: the name of the list_struct within the struct.
+ *
+ * Note that if the list is empty, it returns NULL.
+ */
+#define list_first_entry_or_null(ptr, type, member) \
+ (!list_empty(ptr) ? list_first_entry(ptr, type, member) : NULL)
+
/**
* list_for_each - iterate over a list
* @pos: the &struct list_head to use as a loop cursor.
}
netdev_features_t netdev_increment_features(netdev_features_t all,
netdev_features_t one, netdev_features_t mask);
+
+/* Allow TSO being used on stacked device :
+ * Performing the GSO segmentation before last device
+ * is a performance improvement.
+ */
+static inline netdev_features_t netdev_add_tso_features(netdev_features_t features,
+ netdev_features_t mask)
+{
+ return netdev_increment_features(features, NETIF_F_ALL_TSO, mask);
+}
+
int __netdev_update_features(struct net_device *dev);
void netdev_update_features(struct net_device *dev);
void netdev_change_features(struct net_device *dev);
extern int ipv6_netfilter_init(void);
extern void ipv6_netfilter_fini(void);
+
+/*
+ * Hook functions for ipv6 to allow xt_* modules to be built-in even
+ * if IPv6 is a module.
+ */
+struct nf_ipv6_ops {
+ int (*chk_addr)(struct net *net, const struct in6_addr *addr,
+ const struct net_device *dev, int strict);
+};
+
+extern const struct nf_ipv6_ops __rcu *nf_ipv6_ops;
+static inline const struct nf_ipv6_ops *nf_get_ipv6_ops(void)
+{
+ return rcu_dereference(nf_ipv6_ops);
+}
+
#else /* CONFIG_NETFILTER */
static inline int ipv6_netfilter_init(void) { return 0; }
static inline void ipv6_netfilter_fini(void) { return; }
void acpiphp_init(void);
void acpiphp_enumerate_slots(struct pci_bus *bus, acpi_handle handle);
void acpiphp_remove_slots(struct pci_bus *bus);
+void acpiphp_check_host_bridge(acpi_handle handle);
#else
static inline void acpiphp_init(void) { }
static inline void acpiphp_enumerate_slots(struct pci_bus *bus,
acpi_handle handle) { }
static inline void acpiphp_remove_slots(struct pci_bus *bus) { }
+static inline void acpiphp_check_host_bridge(acpi_handle handle) { }
#endif
#else /* CONFIG_ACPI */
#ifndef __CLK_LPSS_H
#define __CLK_LPSS_H
+struct lpss_clk_data {
+ const char *name;
+ struct clk *clk;
+};
+
extern int lpt_clk_init(void);
#endif /* __CLK_LPSS_H */
int DTR_present;
int (*get_context_loss_count)(struct device *);
- void (*set_forceidle)(struct device *);
- void (*set_noidle)(struct device *);
void (*enable_wakeup)(struct device *, bool);
};
pos = hlist_entry_safe(rcu_dereference_raw(hlist_next_rcu(\
&(pos)->member)), typeof(*(pos)), member))
+/**
+ * hlist_for_each_entry_rcu_notrace - iterate over rcu list of given type (for tracing)
+ * @pos: the type * to use as a loop cursor.
+ * @head: the head for your list.
+ * @member: the name of the hlist_node within the struct.
+ *
+ * This list-traversal primitive may safely run concurrently with
+ * the _rcu list-mutation primitives such as hlist_add_head_rcu()
+ * as long as the traversal is guarded by rcu_read_lock().
+ *
+ * This is the same as hlist_for_each_entry_rcu() except that it does
+ * not do any RCU debugging or tracing.
+ */
+#define hlist_for_each_entry_rcu_notrace(pos, head, member) \
+ for (pos = hlist_entry_safe (rcu_dereference_raw_notrace(hlist_first_rcu(head)),\
+ typeof(*(pos)), member); \
+ pos; \
+ pos = hlist_entry_safe(rcu_dereference_raw_notrace(hlist_next_rcu(\
+ &(pos)->member)), typeof(*(pos)), member))
+
/**
* hlist_for_each_entry_rcu_bh - iterate over rcu list of given type
* @pos: the type * to use as a loop cursor.
* @head: the head for your list.
* @member: the name of the hlist_nulls_node within the struct.
*
+ * The barrier() is needed to make sure compiler doesn't cache first element [1],
+ * as this loop can be restarted [2]
+ * [1] Documentation/atomic_ops.txt around line 114
+ * [2] Documentation/RCU/rculist_nulls.txt around line 146
*/
#define hlist_nulls_for_each_entry_rcu(tpos, pos, head, member) \
- for (pos = rcu_dereference_raw(hlist_nulls_first_rcu(head)); \
+ for (({barrier();}), \
+ pos = rcu_dereference_raw(hlist_nulls_first_rcu(head)); \
(!is_a_nulls(pos)) && \
({ tpos = hlist_nulls_entry(pos, typeof(*tpos), member); 1; }); \
pos = rcu_dereference_raw(hlist_nulls_next_rcu(pos)))
#define rcu_dereference_raw(p) rcu_dereference_check(p, 1) /*@@@ needed? @@@*/
+/*
+ * The tracing infrastructure traces RCU (we want that), but unfortunately
+ * some of the RCU checks causes tracing to lock up the system.
+ *
+ * The tracing version of rcu_dereference_raw() must not call
+ * rcu_read_lock_held().
+ */
+#define rcu_dereference_raw_notrace(p) __rcu_dereference_check((p), 1, __rcu)
+
/**
* rcu_access_index() - fetch RCU index with no dereferencing
* @p: The index to read
extern struct bus_type rio_bus_type;
extern struct device rio_bus;
-extern struct list_head rio_devices; /* list of all devices */
struct rio_mport;
struct rio_dev;
* @name: Port name string
* @priv: Master port private data
* @dma: DMA device associated with mport
+ * @nscan: RapidIO network enumeration/discovery operations
*/
struct rio_mport {
struct list_head dbells; /* list of doorbell events */
#ifdef CONFIG_RAPIDIO_DMA_ENGINE
struct dma_device dma;
#endif
+ struct rio_scan *nscan;
};
+/*
+ * Enumeration/discovery control flags
+ */
+#define RIO_SCAN_ENUM_NO_WAIT 0x00000001 /* Do not wait for enum completed */
+
struct rio_id_table {
u16 start; /* logical minimal id */
u32 max; /* max number of IDs in table */
}
#endif /* CONFIG_RAPIDIO_DMA_ENGINE */
+/**
+ * struct rio_scan - RIO enumeration and discovery operations
+ * @enumerate: Callback to perform RapidIO fabric enumeration.
+ * @discover: Callback to perform RapidIO fabric discovery.
+ */
+struct rio_scan {
+ int (*enumerate)(struct rio_mport *mport, u32 flags);
+ int (*discover)(struct rio_mport *mport, u32 flags);
+};
+
/* Architecture and hardware-specific functions */
extern int rio_register_mport(struct rio_mport *);
extern int rio_open_inb_mbox(struct rio_mport *, void *, int, int);
extern struct rio_dev *rio_get_device(u16 vid, u16 did, struct rio_dev *from);
extern struct rio_dev *rio_get_asm(u16 vid, u16 did, u16 asm_vid, u16 asm_did,
struct rio_dev *from);
+extern int rio_init_mports(void);
#endif /* LINUX_RIO_DRV_H */
SKB_GSO_CB(inner_skb)->mac_offset;
}
+static inline int gso_pskb_expand_head(struct sk_buff *skb, int extra)
+{
+ int new_headroom, headroom;
+ int ret;
+
+ headroom = skb_headroom(skb);
+ ret = pskb_expand_head(skb, extra, 0, GFP_ATOMIC);
+ if (ret)
+ return ret;
+
+ new_headroom = skb_headroom(skb);
+ SKB_GSO_CB(skb)->mac_offset += (new_headroom - headroom);
+ return 0;
+}
+
static inline bool skb_is_gso(const struct sk_buff *skb)
{
return skb_shinfo(skb)->gso_size;
struct timespec;
+/* The __sys_...msg variants allow MSG_CMSG_COMPAT */
+extern long __sys_recvmsg(int fd, struct msghdr __user *msg, unsigned flags);
+extern long __sys_sendmsg(int fd, struct msghdr __user *msg, unsigned flags);
extern int __sys_recvmmsg(int fd, struct mmsghdr __user *mmsg, unsigned int vlen,
unsigned int flags, struct timespec *timeout);
extern int __sys_sendmmsg(int fd, struct mmsghdr __user *mmsg,
}
/**
- * gadget_is_superspeed() - return true if the hardware handles
- * supperspeed
- * @g: controller that might support supper speed
+ * gadget_is_superspeed() - return true if the hardware handles superspeed
+ * @g: controller that might support superspeed
*/
static inline int gadget_is_superspeed(struct usb_gadget *g)
{
struct usb_serial_port *port, struct ktermios *old);
void (*break_ctl)(struct tty_struct *tty, int break_state);
int (*chars_in_buffer)(struct tty_struct *tty);
+ void (*wait_until_sent)(struct tty_struct *tty, long timeout);
+ bool (*tx_empty)(struct usb_serial_port *port);
void (*throttle)(struct tty_struct *tty);
void (*unthrottle)(struct tty_struct *tty);
int (*tiocmget)(struct tty_struct *tty);
extern int usb_serial_generic_resume(struct usb_serial *serial);
extern int usb_serial_generic_write_room(struct tty_struct *tty);
extern int usb_serial_generic_chars_in_buffer(struct tty_struct *tty);
+extern void usb_serial_generic_wait_until_sent(struct tty_struct *tty,
+ long timeout);
extern void usb_serial_generic_read_bulk_callback(struct urb *urb);
extern void usb_serial_generic_write_bulk_callback(struct urb *urb);
extern void usb_serial_generic_throttle(struct tty_struct *tty);
int vc_allocate(unsigned int console);
int vc_cons_allocated(unsigned int console);
int vc_resize(struct vc_data *vc, unsigned int cols, unsigned int lines);
-void vc_deallocate(unsigned int console);
+struct vc_data *vc_deallocate(unsigned int console);
void reset_palette(struct vc_data *vc);
void do_blank_screen(int entering_gfx);
void do_unblank_screen(int leaving_gfx);
if (!ret) \
break; \
} \
+ if (!ret && (condition)) \
+ ret = 1; \
finish_wait(&wq, &__wait); \
} while (0)
* wake_up() has to be called after changing any variable that could
* change the result of the wait condition.
*
- * The function returns 0 if the @timeout elapsed, and the remaining
- * jiffies if the condition evaluated to true before the timeout elapsed.
+ * The function returns 0 if the @timeout elapsed, or the remaining
+ * jiffies (at least 1) if the @condition evaluated to %true before
+ * the @timeout elapsed.
*/
#define wait_event_timeout(wq, condition, timeout) \
({ \
ret = -ERESTARTSYS; \
break; \
} \
+ if (!ret && (condition)) \
+ ret = 1; \
finish_wait(&wq, &__wait); \
} while (0)
* wake_up() has to be called after changing any variable that could
* change the result of the wait condition.
*
- * The function returns 0 if the @timeout elapsed, -ERESTARTSYS if it
- * was interrupted by a signal, and the remaining jiffies otherwise
- * if the condition evaluated to true before the timeout elapsed.
+ * Returns:
+ * 0 if the @timeout elapsed, -%ERESTARTSYS if it was interrupted by
+ * a signal, or the remaining jiffies (at least 1) if the @condition
+ * evaluated to %true before the @timeout elapsed.
*/
#define wait_event_interruptible_timeout(wq, condition, timeout) \
({ \
extern int ipv6_chk_addr(struct net *net,
const struct in6_addr *addr,
- struct net_device *dev,
+ const struct net_device *dev,
int strict);
#if defined(CONFIG_IPV6_MIP6) || defined(CONFIG_IPV6_MIP6_MODULE)
* This function may not be called in IRQ context. Calls to this function
* for a single hardware must be synchronized against each other. Calls to
* this function, ieee80211_rx_ni() and ieee80211_rx_irqsafe() may not be
- * mixed for a single hardware.
+ * mixed for a single hardware. Must not run concurrently with
+ * ieee80211_tx_status() or ieee80211_tx_status_ni().
*
* In process context use instead ieee80211_rx_ni().
*
* (internally defers to a tasklet.)
*
* Calls to this function, ieee80211_rx() or ieee80211_rx_ni() may not
- * be mixed for a single hardware.
+ * be mixed for a single hardware.Must not run concurrently with
+ * ieee80211_tx_status() or ieee80211_tx_status_ni().
*
* @hw: the hardware this frame came in on
* @skb: the buffer to receive, owned by mac80211 after this call
* (internally disables bottom halves).
*
* Calls to this function, ieee80211_rx() and ieee80211_rx_irqsafe() may
- * not be mixed for a single hardware.
+ * not be mixed for a single hardware. Must not run concurrently with
+ * ieee80211_tx_status() or ieee80211_tx_status_ni().
*
* @hw: the hardware this frame came in on
* @skb: the buffer to receive, owned by mac80211 after this call
* This function may not be called in IRQ context. Calls to this function
* for a single hardware must be synchronized against each other. Calls
* to this function, ieee80211_tx_status_ni() and ieee80211_tx_status_irqsafe()
- * may not be mixed for a single hardware.
+ * may not be mixed for a single hardware. Must not run concurrently with
+ * ieee80211_rx() or ieee80211_rx_ni().
*
* @hw: the hardware the frame was transmitted by
* @skb: the frame that was transmitted, owned by mac80211 after this call
} u;
};
-typedef void nf_logfn(u_int8_t pf,
+typedef void nf_logfn(struct net *net,
+ u_int8_t pf,
unsigned int hooknum,
const struct sk_buff *skb,
const struct net_device *in,
#define _KER_NFNETLINK_LOG_H
void
-nfulnl_log_packet(u_int8_t pf,
+nfulnl_log_packet(struct net *net,
+ u_int8_t pf,
unsigned int hooknum,
const struct sk_buff *skb,
const struct net_device *in,
#endif
struct psched_ratecfg {
- u64 rate_bps;
- u32 mult;
- u32 shift;
+ u64 rate_bps;
+ u32 mult;
+ u16 overhead;
+ u8 shift;
};
static inline u64 psched_l2t_ns(const struct psched_ratecfg *r,
unsigned int len)
{
- return ((u64)len * r->mult) >> r->shift;
+ return ((u64)(len + r->overhead) * r->mult) >> r->shift;
}
-extern void psched_ratecfg_precompute(struct psched_ratecfg *r, u32 rate);
+extern void psched_ratecfg_precompute(struct psched_ratecfg *r, const struct tc_ratespec *conf);
-static inline u32 psched_ratecfg_getrate(const struct psched_ratecfg *r)
+static inline void psched_ratecfg_getrate(struct tc_ratespec *res,
+ const struct psched_ratecfg *r)
{
- return r->rate_bps >> 3;
+ memset(res, 0, sizeof(*res));
+ res->rate = r->rate_bps >> 3;
+ res->overhead = r->overhead;
}
#endif
}
}
+extern void xfrm_garbage_collect(struct net *net);
+
#else
static inline void xfrm_sk_free_policy(struct sock *sk) {}
{
return 1;
}
+static inline void xfrm_garbage_collect(struct net *net)
+{
+}
#endif
static __inline__
struct list_head sess_list;
struct list_head sess_acl_list;
struct list_head sess_cmd_list;
+ struct list_head sess_wait_list;
spinlock_t sess_cmd_lock;
struct kref sess_kref;
};
void target_execute_cmd(struct se_cmd *cmd);
-void transport_generic_free_cmd(struct se_cmd *, int);
+int transport_generic_free_cmd(struct se_cmd *, int);
bool transport_wait_for_tasks(struct se_cmd *);
int transport_check_aborted_status(struct se_cmd *, int);
int target_get_sess_cmd(struct se_session *, struct se_cmd *, bool);
int target_put_sess_cmd(struct se_session *, struct se_cmd *);
void target_sess_cmd_list_set_waiting(struct se_session *);
-void target_wait_for_sess_cmds(struct se_session *, int);
+void target_wait_for_sess_cmds(struct se_session *);
int core_alua_check_nonop_delay(struct se_cmd *);
};
enum omapdss_version omapdss_get_version(void);
+bool omapdss_is_initialized(void);
int omap_dss_register_driver(struct omap_dss_driver *);
void omap_dss_unregister_driver(struct omap_dss_driver *);
struct device dev;
enum xenbus_state state;
struct completion down;
+ struct work_struct work;
};
static inline struct xenbus_device *to_xenbus_device(struct device *dev)
int otime, struct list_head *pt)
{
int i;
+ int progress;
- if (sma->complex_count || sops == NULL) {
- if (update_queue(sma, -1, pt))
+ progress = 1;
+retry_global:
+ if (sma->complex_count) {
+ if (update_queue(sma, -1, pt)) {
+ progress = 1;
otime = 1;
+ sops = NULL;
+ }
}
+ if (!progress)
+ goto done;
if (!sops) {
/* No semops; something special is going on. */
for (i = 0; i < sma->sem_nsems; i++) {
- if (update_queue(sma, i, pt))
+ if (update_queue(sma, i, pt)) {
otime = 1;
+ progress = 1;
+ }
}
- goto done;
+ goto done_checkretry;
}
/* Check the semaphores that were modified. */
if (sops[i].sem_op > 0 ||
(sops[i].sem_op < 0 &&
sma->sem_base[sops[i].sem_num].semval == 0))
- if (update_queue(sma, sops[i].sem_num, pt))
+ if (update_queue(sma, sops[i].sem_num, pt)) {
otime = 1;
+ progress = 1;
+ }
+ }
+done_checkretry:
+ if (progress) {
+ progress = 0;
+ goto retry_global;
}
done:
if (otime)
* @seq: netlink audit message sequence (serial) number
* @data: payload data
* @datasz: size of payload data
- * @loginuid: loginuid of sender
- * @sessionid: sessionid for netlink audit message
- * @sid: SE Linux Security ID of sender
*/
int audit_receive_filter(int type, int pid, int seq, void *data, size_t datasz)
{
*/
cgroup_drop_root(opts.new_root);
- if (((root->flags | opts.flags) & CGRP_ROOT_SANE_BEHAVIOR) &&
- root->flags != opts.flags) {
- pr_err("cgroup: sane_behavior: new mount options should match the existing superblock\n");
- ret = -EINVAL;
- goto drop_new_super;
+ if (root->flags != opts.flags) {
+ if ((root->flags | opts.flags) & CGRP_ROOT_SANE_BEHAVIOR) {
+ pr_err("cgroup: sane_behavior: new mount options should match the existing superblock\n");
+ ret = -EINVAL;
+ goto drop_new_super;
+ } else {
+ pr_warning("cgroup: new mount options do not match the existing superblock, will be ignored\n");
+ }
}
/* no subsys rebinding, so refcounts don't change */
goto out;
}
+ cfe->type = (void *)cft;
+ cfe->dentry = dentry;
+ dentry->d_fsdata = cfe;
+ simple_xattrs_init(&cfe->xattrs);
+
mode = cgroup_file_mode(cft);
error = cgroup_create_file(dentry, mode | S_IFREG, cgrp->root->sb);
if (!error) {
- cfe->type = (void *)cft;
- cfe->dentry = dentry;
- dentry->d_fsdata = cfe;
- simple_xattrs_init(&cfe->xattrs);
list_add_tail(&cfe->node, &parent->files);
cfe = NULL;
}
WARN_ON_ONCE(!rcu_read_lock_held());
/* if first iteration, pretend we just visited @cgroup */
- if (!pos) {
- if (list_empty(&cgroup->children))
- return NULL;
+ if (!pos)
pos = cgroup;
- }
/* visit the first child if exists */
next = list_first_or_null_rcu(&pos->children, struct cgroup, sibling);
return next;
/* no child, visit my or the closest ancestor's next sibling */
- do {
+ while (pos != cgroup) {
next = list_entry_rcu(pos->sibling.next, struct cgroup,
sibling);
if (&next->sibling != &pos->parent->children)
return next;
pos = pos->parent;
- } while (pos != cgroup);
+ }
return NULL;
}
final_start = min(range[i].start, start);
final_end = max(range[i].end, end);
- range[i].start = final_start;
- range[i].end = final_end;
- return nr_range;
+ /* clear it and add it back for further merge */
+ range[i].start = 0;
+ range[i].end = 0;
+ return add_range_with_merge(range, az, nr_range,
+ final_start, final_end);
}
/* Need to add it: */
/*
* Traverse the ftrace_global_list, invoking all entries. The reason that we
- * can use rcu_dereference_raw() is that elements removed from this list
+ * can use rcu_dereference_raw_notrace() is that elements removed from this list
* are simply leaked, so there is no need to interact with a grace-period
- * mechanism. The rcu_dereference_raw() calls are needed to handle
+ * mechanism. The rcu_dereference_raw_notrace() calls are needed to handle
* concurrent insertions into the ftrace_global_list.
*
* Silly Alpha and silly pointer-speculation compiler optimizations!
*/
#define do_for_each_ftrace_op(op, list) \
- op = rcu_dereference_raw(list); \
+ op = rcu_dereference_raw_notrace(list); \
do
/*
* Optimized for just a single item in the list (as that is the normal case).
*/
#define while_for_each_ftrace_op(op) \
- while (likely(op = rcu_dereference_raw((op)->next)) && \
+ while (likely(op = rcu_dereference_raw_notrace((op)->next)) && \
unlikely((op) != &ftrace_list_end))
static inline void ftrace_ops_init(struct ftrace_ops *ops)
if (hlist_empty(hhd))
return NULL;
- hlist_for_each_entry_rcu(rec, hhd, node) {
+ hlist_for_each_entry_rcu_notrace(rec, hhd, node) {
if (rec->ip == ip)
return rec;
}
hhd = &hash->buckets[key];
- hlist_for_each_entry_rcu(entry, hhd, hlist) {
+ hlist_for_each_entry_rcu_notrace(entry, hhd, hlist) {
if (entry->ip == ip)
return entry;
}
struct ftrace_hash *notrace_hash;
int ret;
- filter_hash = rcu_dereference_raw(ops->filter_hash);
- notrace_hash = rcu_dereference_raw(ops->notrace_hash);
+ filter_hash = rcu_dereference_raw_notrace(ops->filter_hash);
+ notrace_hash = rcu_dereference_raw_notrace(ops->notrace_hash);
if ((ftrace_hash_empty(filter_hash) ||
ftrace_lookup_ip(filter_hash, ip)) &&
* on the hash. rcu_read_lock is too dangerous here.
*/
preempt_disable_notrace();
- hlist_for_each_entry_rcu(entry, hhd, node) {
+ hlist_for_each_entry_rcu_notrace(entry, hhd, node) {
if (entry->ip == ip)
entry->ops->func(ip, parent_ip, &entry->data);
}
if (cpu == RING_BUFFER_ALL_CPUS)
work = &buffer->irq_work;
else {
+ if (!cpumask_test_cpu(cpu, buffer->cpumask))
+ return -EINVAL;
+
cpu_buffer = buffer->buffers[cpu];
work = &cpu_buffer->irq_work;
}
memcpy(max_data->comm, tsk->comm, TASK_COMM_LEN);
max_data->pid = tsk->pid;
- max_data->uid = task_uid(tsk);
+ /*
+ * If tsk == current, then use current_uid(), as that does not use
+ * RCU. The irq tracer can be called out of RCU scope.
+ */
+ if (tsk == current)
+ max_data->uid = current_uid();
+ else
+ max_data->uid = task_uid(tsk);
+
max_data->nice = tsk->static_prio - 20 - MAX_RT_PRIO;
max_data->policy = tsk->policy;
max_data->rt_priority = tsk->rt_priority;
trace_init_cmdlines();
- register_tracer(&nop_trace);
-
+ /*
+ * register_tracer() might reference current_trace, so it
+ * needs to be set before we register anything. This is
+ * just a bootstrap of current_trace anyway.
+ */
global_trace.current_trace = &nop_trace;
+ register_tracer(&nop_trace);
+
/* All seems OK, enable tracing */
tracing_disabled = 0;
out_reg:
/* Don't let event modules unload while probe registered */
ret = try_module_get(file->event_call->mod);
- if (!ret)
+ if (!ret) {
+ ret = -EBUSY;
goto out_free;
+ }
ret = __ftrace_event_enable_disable(file, 1, 1);
if (ret < 0)
/* stop the tracing. */
tracing_stop();
/* check the trace buffer */
- ret = trace_test_buffer(tr, &count);
+ ret = trace_test_buffer(&tr->trace_buffer, &count);
trace->reset(tr);
tracing_start();
lib-y := ctype.o string.o vsprintf.o cmdline.o \
rbtree.o radix-tree.o dump_stack.o timerqueue.o\
- idr.o int_sqrt.o extable.o iovec.o \
+ idr.o int_sqrt.o extable.o \
sha1.o md5.o irq_regs.o reciprocal_div.o argv_split.o \
proportions.o flex_proportions.o prio_heap.o ratelimit.o show_mem.o \
is_single_threaded.o plist.o decompress.o kobject_uevent.o \
obj-y += bcd.o div64.o sort.o parser.o halfmd4.o debug_locks.o random32.o \
bust_spinlocks.o hexdump.o kasprintf.o bitmap.o scatterlist.o \
- gcd.o lcm.o list_sort.o uuid.o flex_array.o \
+ gcd.o lcm.o list_sort.o uuid.o flex_array.o iovec.o \
bsearch.o find_last_bit.o find_next_bit.o llist.o memweight.o kfifo.o
obj-y += string_helpers.o
obj-$(CONFIG_TEST_STRING_HELPERS) += test-string_helpers.o
if (waiter->node != n)
continue;
+ list_del(&waiter->list);
waiter->woken = 1;
mb();
wake_up_process(waiter->process);
- list_del(&waiter->list);
}
spin_unlock(&klist_remove_lock);
knode_set_klist(n, NULL);
"rM" ((USItype)(bh)), \
"rM" ((USItype)(al)), \
"rM" ((USItype)(bl)))
-#if defined(_PA_RISC1_1)
+#if 0 && defined(_PA_RISC1_1)
+/* xmpyu uses floating point register which is not allowed in Linux kernel. */
#define umul_ppmm(wh, wl, u, v) \
do { \
union {UDItype __ll; \
#define UMUL_TIME 40
#define UDIV_TIME 80
#endif
-#ifndef LONGLONG_STANDALONE
+#if 0 /* #ifndef LONGLONG_STANDALONE */
#define udiv_qrnnd(q, r, n1, n0, d) \
do { USItype __r; \
(q) = __udiv_qrnnd(&__r, (n1), (n0), (d)); \
pte_unmap(pte);
spin_lock(&mm->page_table_lock);
BUG_ON(!pmd_none(*pmd));
- set_pmd_at(mm, address, pmd, _pmd);
+ /*
+ * We can only use set_pmd_at when establishing
+ * hugepmds and never for establishing regular pmds that
+ * points to regular pagetables. Use pmd_populate for that
+ */
+ pmd_populate(mm, pmd, pmd_pgtable(_pmd));
spin_unlock(&mm->page_table_lock);
anon_vma_unlock_write(vma->anon_vma);
goto out;
if (mem_cgroup_disabled())
return NULL;
- VM_BUG_ON(PageSwapCache(page));
-
if (PageTransHuge(page)) {
nr_pages <<= compound_order(page);
VM_BUG_ON(!PageTransHuge(page));
if (page_mapped(page))
return;
VM_BUG_ON(page->mapping && !PageAnon(page));
+ /*
+ * If the page is in swap cache, uncharge should be deferred
+ * to the swap path, which also properly accounts swap usage
+ * and handles memcg lifetime.
+ *
+ * Note that this check is not stable and reclaim may add the
+ * page to swap cache at any time after this. However, if the
+ * page is not in swap cache by the time page->mapcount hits
+ * 0, there won't be any page table references to the swap
+ * slot, and reclaim will free it and not actually write the
+ * page to disk.
+ */
if (PageSwapCache(page))
return;
__mem_cgroup_uncharge_common(page, MEM_CGROUP_CHARGE_TYPE_ANON, false);
tlb->start = -1UL;
tlb->end = 0;
tlb->need_flush = 0;
- tlb->fast_mode = (num_possible_cpus() == 1);
tlb->local.next = NULL;
tlb->local.nr = 0;
tlb->local.max = ARRAY_SIZE(tlb->__pages);
tlb_table_flush(tlb);
#endif
- if (tlb_fast_mode(tlb))
- return;
-
for (batch = &tlb->local; batch; batch = batch->next) {
free_pages_and_swap_cache(batch->pages, batch->nr);
batch->nr = 0;
VM_BUG_ON(!tlb->need_flush);
- if (tlb_fast_mode(tlb)) {
- free_page_and_swap_cache(page);
- return 1; /* avoid calling tlb_flush_mmu() */
- }
-
batch = tlb->active;
batch->pages[batch->nr++] = page;
if (batch->nr == batch->max) {
start = phys_start_pfn << PAGE_SHIFT;
size = nr_pages * PAGE_SIZE;
ret = release_mem_region_adjustable(&iomem_resource, start, size);
- if (ret)
- pr_warn("Unable to release resource <%016llx-%016llx> (%d)\n",
- start, start + size - 1, ret);
+ if (ret) {
+ resource_size_t endres = start + size - 1;
+
+ pr_warn("Unable to release resource <%pa-%pa> (%d)\n",
+ &start, &endres, ret);
+ }
sections_to_remove = nr_pages / PAGES_PER_SECTION;
for (i = 0; i < sections_to_remove; i++) {
pte = arch_make_huge_pte(pte, vma, new, 0);
}
#endif
- flush_cache_page(vma, addr, pte_pfn(pte));
+ flush_dcache_page(new);
set_pte_at(mm, addr, ptep, pte);
if (PageHuge(new)) {
int id;
/*
- * srcu_read_lock() here will block synchronize_srcu() in
- * mmu_notifier_unregister() until all registered
- * ->release() callouts this function makes have
- * returned.
+ * SRCU here will block mmu_notifier_unregister until
+ * ->release returns.
*/
id = srcu_read_lock(&srcu);
+ hlist_for_each_entry_rcu(mn, &mm->mmu_notifier_mm->list, hlist)
+ /*
+ * If ->release runs before mmu_notifier_unregister it must be
+ * handled, as it's the only way for the driver to flush all
+ * existing sptes and stop the driver from establishing any more
+ * sptes before all the pages in the mm are freed.
+ */
+ if (mn->ops->release)
+ mn->ops->release(mn, mm);
+ srcu_read_unlock(&srcu, id);
+
spin_lock(&mm->mmu_notifier_mm->lock);
while (unlikely(!hlist_empty(&mm->mmu_notifier_mm->list))) {
mn = hlist_entry(mm->mmu_notifier_mm->list.first,
struct mmu_notifier,
hlist);
-
/*
- * Unlink. This will prevent mmu_notifier_unregister()
- * from also making the ->release() callout.
+ * We arrived before mmu_notifier_unregister so
+ * mmu_notifier_unregister will do nothing other than to wait
+ * for ->release to finish and for mmu_notifier_unregister to
+ * return.
*/
hlist_del_init_rcu(&mn->hlist);
- spin_unlock(&mm->mmu_notifier_mm->lock);
-
- /*
- * Clear sptes. (see 'release' description in mmu_notifier.h)
- */
- if (mn->ops->release)
- mn->ops->release(mn, mm);
-
- spin_lock(&mm->mmu_notifier_mm->lock);
}
spin_unlock(&mm->mmu_notifier_mm->lock);
/*
- * All callouts to ->release() which we have done are complete.
- * Allow synchronize_srcu() in mmu_notifier_unregister() to complete
- */
- srcu_read_unlock(&srcu, id);
-
- /*
- * mmu_notifier_unregister() may have unlinked a notifier and may
- * still be calling out to it. Additionally, other notifiers
- * may have been active via vmtruncate() et. al. Block here
- * to ensure that all notifier callouts for this mm have been
- * completed and the sptes are really cleaned up before returning
- * to exit_mmap().
+ * synchronize_srcu here prevents mmu_notifier_release from returning to
+ * exit_mmap (which would proceed with freeing all pages in the mm)
+ * until the ->release method returns, if it was invoked by
+ * mmu_notifier_unregister.
+ *
+ * The mmu_notifier_mm can't go away from under us because one mm_count
+ * is held by exit_mmap.
*/
synchronize_srcu(&srcu);
}
{
BUG_ON(atomic_read(&mm->mm_count) <= 0);
- spin_lock(&mm->mmu_notifier_mm->lock);
if (!hlist_unhashed(&mn->hlist)) {
+ /*
+ * SRCU here will force exit_mmap to wait for ->release to
+ * finish before freeing the pages.
+ */
int id;
+ id = srcu_read_lock(&srcu);
/*
- * Ensure we synchronize up with __mmu_notifier_release().
+ * exit_mmap will block in mmu_notifier_release to guarantee
+ * that ->release is called before freeing the pages.
*/
- id = srcu_read_lock(&srcu);
-
- hlist_del_rcu(&mn->hlist);
- spin_unlock(&mm->mmu_notifier_mm->lock);
-
if (mn->ops->release)
mn->ops->release(mn, mm);
+ srcu_read_unlock(&srcu, id);
+ spin_lock(&mm->mmu_notifier_mm->lock);
/*
- * Allow __mmu_notifier_release() to complete.
+ * Can not use list_del_rcu() since __mmu_notifier_release
+ * can delete it before we hold the lock.
*/
- srcu_read_unlock(&srcu, id);
- } else
+ hlist_del_init_rcu(&mn->hlist);
spin_unlock(&mm->mmu_notifier_mm->lock);
+ }
/*
- * Wait for any running method to finish, including ->release() if it
- * was run by __mmu_notifier_release() instead of us.
+ * Wait for any running method to finish, of course including
+ * ->release if it was run by mmu_notifier_relase instead of us.
*/
synchronize_srcu(&srcu);
return 0;
}
-static struct vm_area_struct* hugetlb_vma(unsigned long addr, struct mm_walk *walk)
-{
- struct vm_area_struct *vma;
-
- /* We don't need vma lookup at all. */
- if (!walk->hugetlb_entry)
- return NULL;
-
- VM_BUG_ON(!rwsem_is_locked(&walk->mm->mmap_sem));
- vma = find_vma(walk->mm, addr);
- if (vma && vma->vm_start <= addr && is_vm_hugetlb_page(vma))
- return vma;
-
- return NULL;
-}
-
#else /* CONFIG_HUGETLB_PAGE */
-static struct vm_area_struct* hugetlb_vma(unsigned long addr, struct mm_walk *walk)
-{
- return NULL;
-}
-
static int walk_hugetlb_range(struct vm_area_struct *vma,
unsigned long addr, unsigned long end,
struct mm_walk *walk)
if (!walk->mm)
return -EINVAL;
+ VM_BUG_ON(!rwsem_is_locked(&walk->mm->mmap_sem));
+
pgd = pgd_offset(walk->mm, addr);
do {
- struct vm_area_struct *vma;
+ struct vm_area_struct *vma = NULL;
next = pgd_addr_end(addr, end);
/*
- * handle hugetlb vma individually because pagetable walk for
- * the hugetlb page is dependent on the architecture and
- * we can't handled it in the same manner as non-huge pages.
+ * This function was not intended to be vma based.
+ * But there are vma special cases to be handled:
+ * - hugetlb vma's
+ * - VM_PFNMAP vma's
*/
- vma = hugetlb_vma(addr, walk);
+ vma = find_vma(walk->mm, addr);
if (vma) {
- if (vma->vm_end < next)
+ /*
+ * There are no page structures backing a VM_PFNMAP
+ * range, so do not allow split_huge_page_pmd().
+ */
+ if ((vma->vm_start <= addr) &&
+ (vma->vm_flags & VM_PFNMAP)) {
next = vma->vm_end;
+ pgd = pgd_offset(walk->mm, next);
+ continue;
+ }
/*
- * Hugepage is very tightly coupled with vma, so
- * walk through hugetlb entries within a given vma.
+ * Handle hugetlb vma individually because pagetable
+ * walk for the hugetlb page is dependent on the
+ * architecture and we can't handled it in the same
+ * manner as non-huge pages.
*/
- err = walk_hugetlb_range(vma, addr, next, walk);
- if (err)
- break;
- pgd = pgd_offset(walk->mm, next);
- continue;
+ if (walk->hugetlb_entry && (vma->vm_start <= addr) &&
+ is_vm_hugetlb_page(vma)) {
+ if (vma->vm_end < next)
+ next = vma->vm_end;
+ /*
+ * Hugepage is very tightly coupled with vma,
+ * so walk through hugetlb entries within a
+ * given vma.
+ */
+ err = walk_hugetlb_range(vma, addr, next, walk);
+ if (err)
+ break;
+ pgd = pgd_offset(walk->mm, next);
+ continue;
+ }
}
if (pgd_none_or_clear_bad(pgd)) {
*/
del_timer_sync(&app->join_timer);
- spin_lock(&app->lock);
+ spin_lock_bh(&app->lock);
mrp_mad_event(app, MRP_EVENT_TX);
mrp_pdu_queue(app);
- spin_unlock(&app->lock);
+ spin_unlock_bh(&app->lock);
mrp_queue_xmit(app);
batadv_originator_free(bat_priv);
free_percpu(bat_priv->bat_counters);
+ bat_priv->bat_counters = NULL;
atomic_set(&bat_priv->mesh_state, BATADV_MESH_INACTIVE);
}
kfree(orig_node);
}
+/**
+ * batadv_orig_node_free_ref - decrement the orig node refcounter and possibly
+ * schedule an rcu callback for freeing it
+ * @orig_node: the orig node to free
+ */
void batadv_orig_node_free_ref(struct batadv_orig_node *orig_node)
{
if (atomic_dec_and_test(&orig_node->refcount))
call_rcu(&orig_node->rcu, batadv_orig_node_free_rcu);
}
+/**
+ * batadv_orig_node_free_ref_now - decrement the orig node refcounter and
+ * possibly free it (without rcu callback)
+ * @orig_node: the orig node to free
+ */
+void batadv_orig_node_free_ref_now(struct batadv_orig_node *orig_node)
+{
+ if (atomic_dec_and_test(&orig_node->refcount))
+ batadv_orig_node_free_rcu(&orig_node->rcu);
+}
+
void batadv_originator_free(struct batadv_priv *bat_priv)
{
struct batadv_hashtable *hash = bat_priv->orig_hash;
void batadv_originator_free(struct batadv_priv *bat_priv);
void batadv_purge_orig_ref(struct batadv_priv *bat_priv);
void batadv_orig_node_free_ref(struct batadv_orig_node *orig_node);
+void batadv_orig_node_free_ref_now(struct batadv_orig_node *orig_node);
struct batadv_orig_node *batadv_get_orig_node(struct batadv_priv *bat_priv,
const uint8_t *addr);
struct batadv_neigh_node *
batadv_debugfs_del_meshif(dev);
free_bat_counters:
free_percpu(bat_priv->bat_counters);
+ bat_priv->bat_counters = NULL;
return ret;
}
struct batadv_tt_orig_list_entry *orig_entry;
orig_entry = container_of(rcu, struct batadv_tt_orig_list_entry, rcu);
- batadv_orig_node_free_ref(orig_entry->orig_node);
+
+ /* We are in an rcu callback here, therefore we cannot use
+ * batadv_orig_node_free_ref() and its call_rcu():
+ * An rcu_barrier() wouldn't wait for that to finish
+ */
+ batadv_orig_node_free_ref_now(orig_entry->orig_node);
kfree(orig_entry);
}
}
static void
-ebt_log_packet(u_int8_t pf, unsigned int hooknum,
- const struct sk_buff *skb, const struct net_device *in,
- const struct net_device *out, const struct nf_loginfo *loginfo,
- const char *prefix)
+ebt_log_packet(struct net *net, u_int8_t pf, unsigned int hooknum,
+ const struct sk_buff *skb, const struct net_device *in,
+ const struct net_device *out, const struct nf_loginfo *loginfo,
+ const char *prefix)
{
unsigned int bitmask;
- struct net *net = dev_net(in ? in : out);
/* FIXME: Disabled from containers until syslog ns is supported */
if (!net_eq(net, &init_net))
nf_log_packet(net, NFPROTO_BRIDGE, par->hooknum, skb,
par->in, par->out, &li, "%s", info->prefix);
else
- ebt_log_packet(NFPROTO_BRIDGE, par->hooknum, skb, par->in,
+ ebt_log_packet(net, NFPROTO_BRIDGE, par->hooknum, skb, par->in,
par->out, &li, info->prefix);
return EBT_CONTINUE;
}
return skb;
}
-static void ebt_ulog_packet(unsigned int hooknr, const struct sk_buff *skb,
- const struct net_device *in, const struct net_device *out,
- const struct ebt_ulog_info *uloginfo, const char *prefix)
+static void ebt_ulog_packet(struct net *net, unsigned int hooknr,
+ const struct sk_buff *skb,
+ const struct net_device *in,
+ const struct net_device *out,
+ const struct ebt_ulog_info *uloginfo,
+ const char *prefix)
{
ebt_ulog_packet_msg_t *pm;
size_t size, copy_len;
struct nlmsghdr *nlh;
- struct net *net = dev_net(in ? in : out);
struct ebt_ulog_net *ebt = ebt_ulog_pernet(net);
unsigned int group = uloginfo->nlgroup;
ebt_ulog_buff_t *ub = &ebt->ulog_buffers[group];
}
/* this function is registered with the netfilter core */
-static void ebt_log_packet(u_int8_t pf, unsigned int hooknum,
+static void ebt_log_packet(struct net *net, u_int8_t pf, unsigned int hooknum,
const struct sk_buff *skb, const struct net_device *in,
const struct net_device *out, const struct nf_loginfo *li,
const char *prefix)
strlcpy(loginfo.prefix, prefix, sizeof(loginfo.prefix));
}
- ebt_ulog_packet(hooknum, skb, in, out, &loginfo, prefix);
+ ebt_ulog_packet(net, hooknum, skb, in, out, &loginfo, prefix);
}
static unsigned int
ebt_ulog_tg(struct sk_buff *skb, const struct xt_action_param *par)
{
- ebt_ulog_packet(par->hooknum, skb, par->in, par->out,
+ struct net *net = dev_net(par->in ? par->in : par->out);
+
+ ebt_ulog_packet(net, par->hooknum, skb, par->in, par->out,
par->targinfo, NULL);
return EBT_CONTINUE;
}
asmlinkage long compat_sys_sendmsg(int fd, struct compat_msghdr __user *msg, unsigned int flags)
{
- return sys_sendmsg(fd, (struct msghdr __user *)msg, flags | MSG_CMSG_COMPAT);
+ if (flags & MSG_CMSG_COMPAT)
+ return -EINVAL;
+ return __sys_sendmsg(fd, (struct msghdr __user *)msg, flags | MSG_CMSG_COMPAT);
}
asmlinkage long compat_sys_sendmmsg(int fd, struct compat_mmsghdr __user *mmsg,
unsigned int vlen, unsigned int flags)
{
+ if (flags & MSG_CMSG_COMPAT)
+ return -EINVAL;
return __sys_sendmmsg(fd, (struct mmsghdr __user *)mmsg, vlen,
flags | MSG_CMSG_COMPAT);
}
asmlinkage long compat_sys_recvmsg(int fd, struct compat_msghdr __user *msg, unsigned int flags)
{
- return sys_recvmsg(fd, (struct msghdr __user *)msg, flags | MSG_CMSG_COMPAT);
+ if (flags & MSG_CMSG_COMPAT)
+ return -EINVAL;
+ return __sys_recvmsg(fd, (struct msghdr __user *)msg, flags | MSG_CMSG_COMPAT);
}
asmlinkage long compat_sys_recv(int fd, void __user *buf, size_t len, unsigned int flags)
int datagrams;
struct timespec ktspec;
+ if (flags & MSG_CMSG_COMPAT)
+ return -EINVAL;
+
if (COMPAT_USE_64BIT_TIME)
return __sys_recvmmsg(fd, (struct mmsghdr __user *)mmsg, vlen,
flags | MSG_CMSG_COMPAT,
ha->refcount = 1;
ha->global_use = global;
ha->synced = sync;
+ ha->sync_cnt = 0;
list_add_tail_rcu(&ha->list, &list->list);
list->count++;
}
if (sync) {
if (ha->synced)
- return 0;
+ return -EEXIST;
else
ha->synced = true;
}
err = __hw_addr_add_ex(to_list, ha->addr, addr_len, ha->type,
false, true);
- if (err)
+ if (err && err != -EEXIST)
return err;
- ha->sync_cnt++;
- ha->refcount++;
+
+ if (!err) {
+ ha->sync_cnt++;
+ ha->refcount++;
+ }
return 0;
}
if (err)
return;
ha->sync_cnt--;
- __hw_addr_del_entry(from_list, ha, false, true);
+ /* address on from list is not marked synced */
+ __hw_addr_del_entry(from_list, ha, false, false);
}
static int __hw_addr_sync_multiple(struct netdev_hw_addr_list *to_list,
return -EINVAL;
netif_addr_lock_nested(to);
- err = __hw_addr_sync(&to->mc, &from->mc, to->addr_len);
+ err = __hw_addr_sync_multiple(&to->mc, &from->mc, to->addr_len);
if (!err)
__dev_set_rx_mode(to);
netif_addr_unlock(to);
* the tail pointer in struct sk_buff!
*/
memset(skb, 0, offsetof(struct sk_buff, tail));
- skb->data = NULL;
+ skb->head = NULL;
skb->truesize = sizeof(struct sk_buff);
atomic_set(&skb->users, 1);
static void skb_release_all(struct sk_buff *skb)
{
skb_release_head_state(skb);
- if (likely(skb->data))
+ if (likely(skb->head))
skb_release_data(skb);
}
"sk_lock-AF_TIPC" , "sk_lock-AF_BLUETOOTH", "sk_lock-IUCV" ,
"sk_lock-AF_RXRPC" , "sk_lock-AF_ISDN" , "sk_lock-AF_PHONET" ,
"sk_lock-AF_IEEE802154", "sk_lock-AF_CAIF" , "sk_lock-AF_ALG" ,
- "sk_lock-AF_NFC" , "sk_lock-AF_MAX"
+ "sk_lock-AF_NFC" , "sk_lock-AF_VSOCK" , "sk_lock-AF_MAX"
};
static const char *const af_family_slock_key_strings[AF_MAX+1] = {
"slock-AF_UNSPEC", "slock-AF_UNIX" , "slock-AF_INET" ,
"slock-AF_TIPC" , "slock-AF_BLUETOOTH", "slock-AF_IUCV" ,
"slock-AF_RXRPC" , "slock-AF_ISDN" , "slock-AF_PHONET" ,
"slock-AF_IEEE802154", "slock-AF_CAIF" , "slock-AF_ALG" ,
- "slock-AF_NFC" , "slock-AF_MAX"
+ "slock-AF_NFC" , "slock-AF_VSOCK" ,"slock-AF_MAX"
};
static const char *const af_family_clock_key_strings[AF_MAX+1] = {
"clock-AF_UNSPEC", "clock-AF_UNIX" , "clock-AF_INET" ,
"clock-AF_TIPC" , "clock-AF_BLUETOOTH", "clock-AF_IUCV" ,
"clock-AF_RXRPC" , "clock-AF_ISDN" , "clock-AF_PHONET" ,
"clock-AF_IEEE802154", "clock-AF_CAIF" , "clock-AF_ALG" ,
- "clock-AF_NFC" , "clock-AF_MAX"
+ "clock-AF_NFC" , "clock-AF_VSOCK" , "clock-AF_MAX"
};
/*
*/
struct net *net = dev_net(skb->dev);
struct ip_tunnel_net *itn;
- const struct iphdr *iph = (const struct iphdr *)skb->data;
+ const struct iphdr *iph;
const int type = icmp_hdr(skb)->type;
const int code = icmp_hdr(skb)->code;
struct ip_tunnel *t;
else
itn = net_generic(net, ipgre_net_id);
+ iph = (const struct iphdr *)skb->data;
t = ip_tunnel_lookup(itn, skb->dev->ifindex, tpi.flags,
iph->daddr, iph->saddr, tpi.key);
inner_iph = (const struct iphdr *)skb_inner_network_header(skb);
+ memset(IPCB(skb), 0, sizeof(*IPCB(skb)));
dst = tnl_params->daddr;
if (dst == 0) {
/* NBMA tunnel */
skb_dst_drop(skb);
skb_dst_set(skb, &rt->dst);
- memset(IPCB(skb), 0, sizeof(*IPCB(skb)));
/* Push down and install the IP header. */
skb_push(skb, sizeof(struct iphdr));
return skb;
}
-static void ipt_ulog_packet(unsigned int hooknum,
+static void ipt_ulog_packet(struct net *net,
+ unsigned int hooknum,
const struct sk_buff *skb,
const struct net_device *in,
const struct net_device *out,
size_t size, copy_len;
struct nlmsghdr *nlh;
struct timeval tv;
- struct net *net = dev_net(in ? in : out);
struct ulog_net *ulog = ulog_pernet(net);
/* ffs == find first bit set, necessary because userspace
put_unaligned(tv.tv_usec, &pm->timestamp_usec);
put_unaligned(skb->mark, &pm->mark);
pm->hook = hooknum;
- if (prefix != NULL)
- strncpy(pm->prefix, prefix, sizeof(pm->prefix));
+ if (prefix != NULL) {
+ strncpy(pm->prefix, prefix, sizeof(pm->prefix) - 1);
+ pm->prefix[sizeof(pm->prefix) - 1] = '\0';
+ }
else if (loginfo->prefix[0] != '\0')
strncpy(pm->prefix, loginfo->prefix, sizeof(pm->prefix));
else
static unsigned int
ulog_tg(struct sk_buff *skb, const struct xt_action_param *par)
{
- ipt_ulog_packet(par->hooknum, skb, par->in, par->out,
+ struct net *net = dev_net(par->in ? par->in : par->out);
+
+ ipt_ulog_packet(net, par->hooknum, skb, par->in, par->out,
par->targinfo, NULL);
return XT_CONTINUE;
}
-static void ipt_logfn(u_int8_t pf,
+static void ipt_logfn(struct net *net,
+ u_int8_t pf,
unsigned int hooknum,
const struct sk_buff *skb,
const struct net_device *in,
strlcpy(loginfo.prefix, prefix, sizeof(loginfo.prefix));
}
- ipt_ulog_packet(hooknum, skb, in, out, &loginfo, prefix);
+ ipt_ulog_packet(net, hooknum, skb, in, out, &loginfo, prefix);
}
static int ulog_tg_check(const struct xt_tgchk_param *par)
{
struct rtable *rt;
struct flowi4 fl4;
+ const struct iphdr *iph = (const struct iphdr *) skb->data;
+ int oif = skb->dev->ifindex;
+ u8 tos = RT_TOS(iph->tos);
+ u8 prot = iph->protocol;
+ u32 mark = skb->mark;
rt = (struct rtable *) dst;
- ip_rt_build_flow_key(&fl4, sk, skb);
+ __build_flow_key(&fl4, sk, iph, oif, tos, prot, mark, 0);
__ip_do_redirect(rt, skb, &fl4, true);
}
unsigned int mss;
struct sk_buff *gso_skb = skb;
__sum16 newcheck;
+ bool ooo_okay, copy_destructor;
if (!pskb_may_pull(skb, sizeof(*th)))
goto out;
goto out;
}
+ copy_destructor = gso_skb->destructor == tcp_wfree;
+ ooo_okay = gso_skb->ooo_okay;
+ /* All segments but the first should have ooo_okay cleared */
+ skb->ooo_okay = 0;
+
segs = skb_segment(skb, features);
if (IS_ERR(segs))
goto out;
+ /* Only first segment might have ooo_okay set */
+ segs->ooo_okay = ooo_okay;
+
delta = htonl(oldlen + (thlen + mss));
skb = segs;
thlen, skb->csum));
seq += mss;
+ if (copy_destructor) {
+ skb->destructor = gso_skb->destructor;
+ skb->sk = gso_skb->sk;
+ /* {tcp|sock}_wfree() use exact truesize accounting :
+ * sum(skb->truesize) MUST be exactly be gso_skb->truesize
+ * So we account mss bytes of 'true size' for each segment.
+ * The last segment will contain the remaining.
+ */
+ skb->truesize = mss;
+ gso_skb->truesize -= mss;
+ }
skb = skb->next;
th = tcp_hdr(skb);
* is freed at TX completion, and not right now when gso_skb
* is freed by GSO engine
*/
- if (gso_skb->destructor == tcp_wfree) {
+ if (copy_destructor) {
swap(gso_skb->sk, skb->sk);
swap(gso_skb->destructor, skb->destructor);
swap(gso_skb->truesize, skb->truesize);
for (i = 0; i < shi->nr_frags; ++i) {
const struct skb_frag_struct *f = &shi->frags[i];
- struct page *page = skb_frag_page(f);
- sg_set_page(&sg, page, skb_frag_size(f), f->page_offset);
+ unsigned int offset = f->page_offset;
+ struct page *page = skb_frag_page(f) + (offset >> PAGE_SHIFT);
+
+ sg_set_page(&sg, page, skb_frag_size(f),
+ offset_in_page(offset));
if (crypto_hash_update(desc, &sg, skb_frag_size(f)))
return 1;
}
* tcp_xmit_retransmit_queue().
*/
static void tcp_fastretrans_alert(struct sock *sk, int pkts_acked,
- int prior_sacked, bool is_dupack,
- int flag)
+ int prior_sacked, int prior_packets,
+ bool is_dupack, int flag)
{
struct inet_connection_sock *icsk = inet_csk(sk);
struct tcp_sock *tp = tcp_sk(sk);
tcp_add_reno_sack(sk);
} else
do_lost = tcp_try_undo_partial(sk, pkts_acked);
- newly_acked_sacked = pkts_acked + tp->sacked_out - prior_sacked;
+ newly_acked_sacked = prior_packets - tp->packets_out +
+ tp->sacked_out - prior_sacked;
break;
case TCP_CA_Loss:
tcp_process_loss(sk, flag, is_dupack);
if (is_dupack)
tcp_add_reno_sack(sk);
}
- newly_acked_sacked = pkts_acked + tp->sacked_out - prior_sacked;
+ newly_acked_sacked = prior_packets - tp->packets_out +
+ tp->sacked_out - prior_sacked;
if (icsk->icsk_ca_state <= TCP_CA_Disorder)
tcp_try_undo_dsack(sk);
bool is_dupack = false;
u32 prior_in_flight;
u32 prior_fackets;
- int prior_packets;
+ int prior_packets = tp->packets_out;
int prior_sacked = tp->sacked_out;
int pkts_acked = 0;
+ int previous_packets_out = 0;
/* If the ack is older than previous acks
* then we can probably ignore it.
sk->sk_err_soft = 0;
icsk->icsk_probes_out = 0;
tp->rcv_tstamp = tcp_time_stamp;
- prior_packets = tp->packets_out;
if (!prior_packets)
goto no_queue;
/* See if we can take anything off of the retransmit queue. */
+ previous_packets_out = tp->packets_out;
flag |= tcp_clean_rtx_queue(sk, prior_fackets, prior_snd_una);
- pkts_acked = prior_packets - tp->packets_out;
+ pkts_acked = previous_packets_out - tp->packets_out;
if (tcp_ack_is_dubious(sk, flag)) {
/* Advance CWND, if state allows this. */
tcp_cong_avoid(sk, ack, prior_in_flight);
is_dupack = !(flag & (FLAG_SND_UNA_ADVANCED | FLAG_NOT_DUP));
tcp_fastretrans_alert(sk, pkts_acked, prior_sacked,
- is_dupack, flag);
+ prior_packets, is_dupack, flag);
} else {
if (flag & FLAG_DATA_ACKED)
tcp_cong_avoid(sk, ack, prior_in_flight);
/* If data was DSACKed, see if we can undo a cwnd reduction. */
if (flag & FLAG_DSACKING_ACK)
tcp_fastretrans_alert(sk, pkts_acked, prior_sacked,
- is_dupack, flag);
+ prior_packets, is_dupack, flag);
/* If this ack opens up a zero window, clear backoff. It was
* being used to time the probes, and is probably far higher than
* it needs to be for normal retransmission.
if (TCP_SKB_CB(skb)->sacked) {
flag |= tcp_sacktag_write_queue(sk, skb, prior_snd_una);
tcp_fastretrans_alert(sk, pkts_acked, prior_sacked,
- is_dupack, flag);
+ prior_packets, is_dupack, flag);
}
SOCK_DEBUG(sk, "Ack %u before %u:%u\n", ack, tp->snd_una, tp->snd_nxt);
&md5);
tcp_header_size = tcp_options_size + sizeof(struct tcphdr);
- if (tcp_packets_in_flight(tp) == 0) {
+ if (tcp_packets_in_flight(tp) == 0)
tcp_ca_event(sk, CA_EVENT_TX_START);
- skb->ooo_okay = 1;
- } else
- skb->ooo_okay = 0;
+
+ /* if no packet is in qdisc/device queue, then allow XPS to select
+ * another queue.
+ */
+ skb->ooo_okay = sk_wmem_alloc_get(sk) == 0;
skb_push(skb, tcp_header_size);
skb_reset_transport_header(skb);
}
int ipv6_chk_addr(struct net *net, const struct in6_addr *addr,
- struct net_device *dev, int strict)
+ const struct net_device *dev, int strict)
{
struct inet6_ifaddr *ifp;
unsigned int hash = inet6_addr_hash(addr);
sp_rt = addrconf_dst_alloc(idev, &sp_ifa->addr, 0);
/* Failure cases are ignored */
- if (!IS_ERR(sp_rt))
+ if (!IS_ERR(sp_rt)) {
+ sp_ifa->rt = sp_rt;
ip6_ins_rt(sp_rt);
+ }
}
read_unlock_bh(&idev->lock);
}
if (WARN_ON(np->cork.opt))
return -EINVAL;
- np->cork.opt = kmalloc(opt->tot_len, sk->sk_allocation);
+ np->cork.opt = kzalloc(opt->tot_len, sk->sk_allocation);
if (unlikely(np->cork.opt == NULL))
return -ENOBUFS;
#include <linux/netfilter.h>
#include <linux/netfilter_ipv6.h>
#include <linux/export.h>
+#include <net/addrconf.h>
#include <net/dst.h>
#include <net/ipv6.h>
#include <net/ip6_route.h>
return csum;
};
+static const struct nf_ipv6_ops ipv6ops = {
+ .chk_addr = ipv6_chk_addr,
+};
+
static const struct nf_afinfo nf_ip6_afinfo = {
.family = AF_INET6,
.checksum = nf_ip6_checksum,
int __init ipv6_netfilter_init(void)
{
+ RCU_INIT_POINTER(nf_ipv6_ops, &ipv6ops);
return nf_register_afinfo(&nf_ip6_afinfo);
}
*/
void ipv6_netfilter_fini(void)
{
+ RCU_INIT_POINTER(nf_ipv6_ops, NULL);
nf_unregister_afinfo(&nf_ip6_afinfo);
}
SNMP_MIB_ITEM("Ip6OutMcastOctets", IPSTATS_MIB_OUTMCASTOCTETS),
SNMP_MIB_ITEM("Ip6InBcastOctets", IPSTATS_MIB_INBCASTOCTETS),
SNMP_MIB_ITEM("Ip6OutBcastOctets", IPSTATS_MIB_OUTBCASTOCTETS),
- SNMP_MIB_ITEM("InCsumErrors", IPSTATS_MIB_CSUMERRORS),
+ /* IPSTATS_MIB_CSUMERRORS is not relevant in IPv6 (no checksum) */
SNMP_MIB_SENTINEL
};
unsigned int mss;
unsigned int unfrag_ip6hlen, unfrag_len;
struct frag_hdr *fptr;
- u8 *mac_start, *prevhdr;
+ u8 *packet_start, *prevhdr;
u8 nexthdr;
u8 frag_hdr_sz = sizeof(struct frag_hdr);
int offset;
__wsum csum;
+ int tnl_hlen;
mss = skb_shinfo(skb)->gso_size;
if (unlikely(skb->len <= mss))
skb->ip_summed = CHECKSUM_NONE;
/* Check if there is enough headroom to insert fragment header. */
- if ((skb_mac_header(skb) < skb->head + frag_hdr_sz) &&
- pskb_expand_head(skb, frag_hdr_sz, 0, GFP_ATOMIC))
- goto out;
+ tnl_hlen = skb_tnl_header_len(skb);
+ if (skb_headroom(skb) < (tnl_hlen + frag_hdr_sz)) {
+ if (gso_pskb_expand_head(skb, tnl_hlen + frag_hdr_sz))
+ goto out;
+ }
/* Find the unfragmentable header and shift it left by frag_hdr_sz
* bytes to insert fragment header.
unfrag_ip6hlen = ip6_find_1stfragopt(skb, &prevhdr);
nexthdr = *prevhdr;
*prevhdr = NEXTHDR_FRAGMENT;
- unfrag_len = skb_network_header(skb) - skb_mac_header(skb) +
- unfrag_ip6hlen;
- mac_start = skb_mac_header(skb);
- memmove(mac_start-frag_hdr_sz, mac_start, unfrag_len);
+ unfrag_len = (skb_network_header(skb) - skb_mac_header(skb)) +
+ unfrag_ip6hlen + tnl_hlen;
+ packet_start = (u8 *) skb->head + SKB_GSO_CB(skb)->mac_offset;
+ memmove(packet_start-frag_hdr_sz, packet_start, unfrag_len);
+ SKB_GSO_CB(skb)->mac_offset -= frag_hdr_sz;
skb->mac_header -= frag_hdr_sz;
skb->network_header -= frag_hdr_sz;
/*
* We now have some discovery info to deliver!
*/
- discovery = kmalloc(sizeof(discovery_t), GFP_ATOMIC);
+ discovery = kzalloc(sizeof(discovery_t), GFP_ATOMIC);
if (!discovery) {
IRDA_WARNING("%s: unable to malloc!\n", __func__);
return;
out:
xfrm_pol_put(xp);
+ if (err == 0)
+ xfrm_garbage_collect(net);
return err;
}
out:
xfrm_pol_put(xp);
+ if (delete && err == 0)
+ xfrm_garbage_collect(net);
return err;
}
void ieee80211_mgd_stop(struct ieee80211_sub_if_data *sdata);
void ieee80211_mgd_conn_tx_status(struct ieee80211_sub_if_data *sdata,
__le16 fc, bool acked);
+void ieee80211_sta_restart(struct ieee80211_sub_if_data *sdata);
/* IBSS code */
void ieee80211_ibss_notify_scan_completed(struct ieee80211_local *local);
return 0;
}
-static int ieee80211_verify_mac(struct ieee80211_local *local, u8 *addr)
+static int ieee80211_verify_mac(struct ieee80211_sub_if_data *sdata, u8 *addr)
{
- struct ieee80211_sub_if_data *sdata;
+ struct ieee80211_local *local = sdata->local;
+ struct ieee80211_sub_if_data *iter;
u64 new, mask, tmp;
u8 *m;
int ret = 0;
mutex_lock(&local->iflist_mtx);
- list_for_each_entry(sdata, &local->interfaces, list) {
- if (sdata->vif.type == NL80211_IFTYPE_MONITOR)
+ list_for_each_entry(iter, &local->interfaces, list) {
+ if (iter == sdata)
+ continue;
+
+ if (iter->vif.type == NL80211_IFTYPE_MONITOR)
continue;
- m = sdata->vif.addr;
+ m = iter->vif.addr;
tmp = ((u64)m[0] << 5*8) | ((u64)m[1] << 4*8) |
((u64)m[2] << 3*8) | ((u64)m[3] << 2*8) |
((u64)m[4] << 1*8) | ((u64)m[5] << 0*8);
if (ieee80211_sdata_running(sdata))
return -EBUSY;
- ret = ieee80211_verify_mac(sdata->local, sa->sa_data);
+ ret = ieee80211_verify_mac(sdata, sa->sa_data);
if (ret)
return ret;
master->control_port_protocol;
sdata->control_port_no_encrypt =
master->control_port_no_encrypt;
+ sdata->vif.cab_queue = master->vif.cab_queue;
+ memcpy(sdata->vif.hw_queue, master->vif.hw_queue,
+ sizeof(sdata->vif.hw_queue));
break;
}
case NL80211_IFTYPE_AP:
ieee80211_recalc_ps(local, -1);
- if (dev) {
+ if (sdata->vif.type == NL80211_IFTYPE_MONITOR ||
+ sdata->vif.type == NL80211_IFTYPE_AP_VLAN) {
+ /* XXX: for AP_VLAN, actually track AP queues */
+ netif_tx_start_all_queues(dev);
+ } else if (dev) {
unsigned long flags;
int n_acs = IEEE80211_NUM_ACS;
int ac;
break;
}
+ /*
+ * Pick address of existing interface in case user changed
+ * MAC address manually, default to perm_addr.
+ */
m = local->hw.wiphy->perm_addr;
+ list_for_each_entry(sdata, &local->interfaces, list) {
+ if (sdata->vif.type == NL80211_IFTYPE_MONITOR)
+ continue;
+ m = sdata->vif.addr;
+ break;
+ }
start = ((u64)m[0] << 5*8) | ((u64)m[1] << 4*8) |
((u64)m[2] << 3*8) | ((u64)m[3] << 2*8) |
((u64)m[4] << 1*8) | ((u64)m[5] << 0*8);
ASSERT_RTNL();
+ /*
+ * Close all AP_VLAN interfaces first, as otherwise they
+ * might be closed while the AP interface they belong to
+ * is closed, causing unregister_netdevice_many() to crash.
+ */
+ list_for_each_entry(sdata, &local->interfaces, list)
+ if (sdata->vif.type == NL80211_IFTYPE_AP_VLAN)
+ dev_close(sdata->dev);
+
mutex_lock(&local->iflist_mtx);
list_for_each_entry_safe(sdata, tmp, &local->interfaces, list) {
list_del(&sdata->list);
static void
ieee80211_sta_process_chanswitch(struct ieee80211_sub_if_data *sdata,
- u64 timestamp, struct ieee802_11_elems *elems)
+ u64 timestamp, struct ieee802_11_elems *elems,
+ bool beacon)
{
struct ieee80211_local *local = sdata->local;
struct ieee80211_if_managed *ifmgd = &sdata->u.mgd;
struct cfg80211_chan_def new_vht_chandef = {};
const struct ieee80211_sec_chan_offs_ie *sec_chan_offs;
const struct ieee80211_wide_bw_chansw_ie *wide_bw_chansw_ie;
+ const struct ieee80211_ht_operation *ht_oper;
int secondary_channel_offset = -1;
ASSERT_MGD_MTX(ifmgd);
sec_chan_offs = elems->sec_chan_offs;
wide_bw_chansw_ie = elems->wide_bw_chansw_ie;
+ ht_oper = elems->ht_operation;
if (ifmgd->flags & (IEEE80211_STA_DISABLE_HT |
IEEE80211_STA_DISABLE_40MHZ)) {
sec_chan_offs = NULL;
wide_bw_chansw_ie = NULL;
+ /* only used for bandwidth here */
+ ht_oper = NULL;
}
if (ifmgd->flags & IEEE80211_STA_DISABLE_VHT)
return;
}
- if (sec_chan_offs) {
+ if (!beacon && sec_chan_offs) {
secondary_channel_offset = sec_chan_offs->sec_chan_offs;
+ } else if (beacon && ht_oper) {
+ secondary_channel_offset =
+ ht_oper->ht_param & IEEE80211_HT_PARAM_CHA_SEC_OFFSET;
} else if (!(ifmgd->flags & IEEE80211_STA_DISABLE_HT)) {
- /* if HT is enabled and the IE not present, it's still HT */
+ /*
+ * If it's not a beacon, HT is enabled and the IE not present,
+ * it's 20 MHz, 802.11-2012 8.5.2.6:
+ * This element [the Secondary Channel Offset Element] is
+ * present when switching to a 40 MHz channel. It may be
+ * present when switching to a 20 MHz channel (in which
+ * case the secondary channel offset is set to SCN).
+ */
secondary_channel_offset = IEEE80211_HT_PARAM_CHA_SEC_NONE;
}
mutex_unlock(&local->iflist_mtx);
}
- ieee80211_sta_process_chanswitch(sdata, rx_status->mactime, elems);
+ ieee80211_sta_process_chanswitch(sdata, rx_status->mactime,
+ elems, true);
}
ieee80211_sta_process_chanswitch(sdata,
rx_status->mactime,
- &elems);
+ &elems, false);
} else if (mgmt->u.action.category == WLAN_CATEGORY_PUBLIC) {
ies_len = skb->len -
offsetof(struct ieee80211_mgmt,
ieee80211_sta_process_chanswitch(sdata,
rx_status->mactime,
- &elems);
+ &elems, false);
}
break;
}
if (WARN_ON_ONCE(!auth_data))
return -EINVAL;
- if (local->hw.flags & IEEE80211_HW_REPORTS_TX_ACK_STATUS)
- tx_flags = IEEE80211_TX_CTL_REQ_TX_STATUS |
- IEEE80211_TX_INTFL_MLME_CONN_TX;
-
auth_data->tries++;
if (auth_data->tries > IEEE80211_AUTH_MAX_TRIES) {
auth_data->expected_transaction = trans;
}
+ if (local->hw.flags & IEEE80211_HW_REPORTS_TX_ACK_STATUS)
+ tx_flags = IEEE80211_TX_CTL_REQ_TX_STATUS |
+ IEEE80211_TX_INTFL_MLME_CONN_TX;
+
ieee80211_send_auth(sdata, trans, auth_data->algorithm, status,
auth_data->data, auth_data->data_len,
auth_data->bss->bssid,
* will not answer to direct packet in unassociated state.
*/
ieee80211_send_probe_req(sdata, NULL, ssidie + 2, ssidie[1],
- NULL, 0, (u32) -1, true, tx_flags,
+ NULL, 0, (u32) -1, true, 0,
auth_data->bss->channel, false);
rcu_read_unlock();
}
- if (!(local->hw.flags & IEEE80211_HW_REPORTS_TX_ACK_STATUS)) {
+ if (tx_flags == 0) {
auth_data->timeout = jiffies + IEEE80211_AUTH_TIMEOUT;
ifmgd->auth_data->timeout_started = true;
run_again(ifmgd, auth_data->timeout);
}
}
+#ifdef CONFIG_PM
+void ieee80211_sta_restart(struct ieee80211_sub_if_data *sdata)
+{
+ struct ieee80211_if_managed *ifmgd = &sdata->u.mgd;
+
+ mutex_lock(&ifmgd->mtx);
+ if (!ifmgd->associated) {
+ mutex_unlock(&ifmgd->mtx);
+ return;
+ }
+
+ if (sdata->flags & IEEE80211_SDATA_DISCONNECT_RESUME) {
+ sdata->flags &= ~IEEE80211_SDATA_DISCONNECT_RESUME;
+ mlme_dbg(sdata, "driver requested disconnect after resume\n");
+ ieee80211_sta_connection_lost(sdata,
+ ifmgd->associated->bssid,
+ WLAN_REASON_UNSPECIFIED,
+ true);
+ mutex_unlock(&ifmgd->mtx);
+ return;
+ }
+ mutex_unlock(&ifmgd->mtx);
+}
+#endif
+
/* interface setup */
void ieee80211_sta_setup_sdata(struct ieee80211_sub_if_data *sdata)
{
struct ieee80211_if_managed *ifmgd = &sdata->u.mgd;
u8 frame_buf[IEEE80211_DEAUTH_FRAME_LEN];
bool tx = !req->local_state_change;
- bool sent_frame = false;
+ bool report_frame = false;
mutex_lock(&ifmgd->mtx);
ieee80211_destroy_auth_data(sdata, false);
mutex_unlock(&ifmgd->mtx);
- sent_frame = tx;
+ report_frame = true;
goto out;
}
ether_addr_equal(ifmgd->associated->bssid, req->bssid)) {
ieee80211_set_disassoc(sdata, IEEE80211_STYPE_DEAUTH,
req->reason_code, tx, frame_buf);
- sent_frame = tx;
+ report_frame = true;
}
mutex_unlock(&ifmgd->mtx);
out:
- if (sent_frame)
+ if (report_frame)
__cfg80211_send_deauth(sdata->dev, frame_buf,
IEEE80211_DEAUTH_FRAME_LEN);
struct ieee80211_sta *pubsta,
struct ieee80211_sta_rates *rates)
{
- struct ieee80211_sta_rates *old = rcu_dereference(pubsta->rates);
+ struct ieee80211_sta_rates *old;
+ /*
+ * mac80211 guarantees that this function will not be called
+ * concurrently, so the following RCU access is safe, even without
+ * extra locking. This can not be checked easily, so we just set
+ * the condition to true.
+ */
+ old = rcu_dereference_protected(pubsta->rates, true);
rcu_assign_pointer(pubsta->rates, rates);
if (old)
kfree_rcu(old, rcu_head);
* and location updates. Note that mac80211
* itself never looks at these frames.
*/
+ if (!multicast &&
+ !ether_addr_equal(sdata->vif.addr, hdr->addr1))
+ return 0;
if (ieee80211_is_public_action(hdr, skb->len))
return 1;
if (!ieee80211_is_beacon(hdr->frame_control))
u32 iv32 = get_unaligned_le32(&data[4]);
u16 iv16 = data[2] | (data[0] << 8);
- spin_lock_bh(&key->u.tkip.txlock);
+ spin_lock(&key->u.tkip.txlock);
ieee80211_compute_tkip_p1k(key, iv32);
tkip_mixing_phase2(tk, ctx, iv16, p2k);
- spin_unlock_bh(&key->u.tkip.txlock);
+ spin_unlock(&key->u.tkip.txlock);
}
EXPORT_SYMBOL(ieee80211_get_tkip_p2k);
mb();
local->resuming = false;
+ list_for_each_entry(sdata, &local->interfaces, list) {
+ if (!ieee80211_sdata_running(sdata))
+ continue;
+ if (sdata->vif.type == NL80211_IFTYPE_STATION)
+ ieee80211_sta_restart(sdata);
+ }
+
mod_timer(&local->sta_cleanup, jiffies + 1);
#else
WARN_ON(1);
const struct nf_afinfo __rcu *nf_afinfo[NFPROTO_NUMPROTO] __read_mostly;
EXPORT_SYMBOL(nf_afinfo);
+const struct nf_ipv6_ops __rcu *nf_ipv6_ops __read_mostly;
+EXPORT_SYMBOL_GPL(nf_ipv6_ops);
int nf_register_afinfo(const struct nf_afinfo *afinfo)
{
return th->rst;
}
+static inline bool is_new_conn(const struct sk_buff *skb,
+ struct ip_vs_iphdr *iph)
+{
+ switch (iph->protocol) {
+ case IPPROTO_TCP: {
+ struct tcphdr _tcph, *th;
+
+ th = skb_header_pointer(skb, iph->len, sizeof(_tcph), &_tcph);
+ if (th == NULL)
+ return false;
+ return th->syn;
+ }
+ case IPPROTO_SCTP: {
+ sctp_chunkhdr_t *sch, schunk;
+
+ sch = skb_header_pointer(skb, iph->len + sizeof(sctp_sctphdr_t),
+ sizeof(schunk), &schunk);
+ if (sch == NULL)
+ return false;
+ return sch->type == SCTP_CID_INIT;
+ }
+ default:
+ return false;
+ }
+}
+
/* Handle response packets: rewrite addresses and send away...
*/
static unsigned int
* Check if the packet belongs to an existing connection entry
*/
cp = pp->conn_in_get(af, skb, &iph, 0);
+
+ if (unlikely(sysctl_expire_nodest_conn(ipvs)) && cp && cp->dest &&
+ unlikely(!atomic_read(&cp->dest->weight)) && !iph.fragoffs &&
+ is_new_conn(skb, &iph)) {
+ ip_vs_conn_expire_now(cp);
+ __ip_vs_conn_put(cp);
+ cp = NULL;
+ }
+
if (unlikely(!cp) && !iph.fragoffs) {
/* No (second) fragments need to enter here, as nf_defrag_ipv6
* replayed fragment zero will already have created the cp
#define IP_VS_SH_TAB_MASK (IP_VS_SH_TAB_SIZE - 1)
struct ip_vs_sh_state {
- struct ip_vs_sh_bucket buckets[IP_VS_SH_TAB_SIZE];
struct rcu_head rcu_head;
+ struct ip_vs_sh_bucket buckets[IP_VS_SH_TAB_SIZE];
};
/*
va_start(args, fmt);
vsnprintf(prefix, sizeof(prefix), fmt, args);
va_end(args);
- logger->logfn(pf, hooknum, skb, in, out, loginfo, prefix);
+ logger->logfn(net, pf, hooknum, skb, in, out, loginfo, prefix);
}
rcu_read_unlock();
}
return 0;
out_sysctl:
+#ifdef CONFIG_PROC_FS
/* For init_net: errors will trigger panic, don't unroll on error. */
if (!net_eq(net, &init_net))
remove_proc_entry("nf_log", net->nf.proc_netfilter);
-
+#endif
return ret;
}
static void __net_exit nf_log_net_exit(struct net *net)
{
netfilter_log_sysctl_exit(net);
+#ifdef CONFIG_PROC_FS
remove_proc_entry("nf_log", net->nf.proc_netfilter);
+#endif
}
static struct pernet_operations nf_log_net_ops = {
/* log handler for internal netfilter logging api */
void
-nfulnl_log_packet(u_int8_t pf,
+nfulnl_log_packet(struct net *net,
+ u_int8_t pf,
unsigned int hooknum,
const struct sk_buff *skb,
const struct net_device *in,
const struct nf_loginfo *li;
unsigned int qthreshold;
unsigned int plen;
- struct net *net = dev_net(in ? in : out);
struct nfnl_log_net *log = nfnl_log_pernet(net);
if (li_user && li_user->type == NF_LOG_TYPE_ULOG)
static void __net_exit nfnl_log_net_exit(struct net *net)
{
+#ifdef CONFIG_PROC_FS
remove_proc_entry("nfnetlink_log", net->nf.proc_netfilter);
+#endif
}
static struct pernet_operations nfnl_log_net_ops = {
static void __net_exit nfnl_queue_net_exit(struct net *net)
{
+#ifdef CONFIG_PROC_FS
remove_proc_entry("nfnetlink_queue", net->nf.proc_netfilter);
+#endif
}
static struct pernet_operations nfnl_queue_net_ops = {
static void
-ipt_log_packet(u_int8_t pf,
+ipt_log_packet(struct net *net,
+ u_int8_t pf,
unsigned int hooknum,
const struct sk_buff *skb,
const struct net_device *in,
const char *prefix)
{
struct sbuff *m;
- struct net *net = dev_net(in ? in : out);
/* FIXME: Disabled from containers until syslog ns is supported */
if (!net_eq(net, &init_net))
dump_sk_uid_gid(m, skb->sk);
/* Max length: 16 "MARK=0xFFFFFFFF " */
- if (!recurse && skb->mark)
+ if (recurse && skb->mark)
sb_add(m, "MARK=0x%x ", skb->mark);
}
}
static void
-ip6t_log_packet(u_int8_t pf,
+ip6t_log_packet(struct net *net,
+ u_int8_t pf,
unsigned int hooknum,
const struct sk_buff *skb,
const struct net_device *in,
const char *prefix)
{
struct sbuff *m;
- struct net *net = dev_net(in ? in : out);
/* FIXME: Disabled from containers until syslog ns is supported */
if (!net_eq(net, &init_net))
{
const struct xt_log_info *loginfo = par->targinfo;
struct nf_loginfo li;
+ struct net *net = dev_net(par->in ? par->in : par->out);
li.type = NF_LOG_TYPE_LOG;
li.u.log.level = loginfo->level;
li.u.log.logflags = loginfo->logflags;
if (par->family == NFPROTO_IPV4)
- ipt_log_packet(NFPROTO_IPV4, par->hooknum, skb, par->in,
+ ipt_log_packet(net, NFPROTO_IPV4, par->hooknum, skb, par->in,
par->out, &li, loginfo->prefix);
#if IS_ENABLED(CONFIG_IP6_NF_IPTABLES)
else if (par->family == NFPROTO_IPV6)
- ip6t_log_packet(NFPROTO_IPV6, par->hooknum, skb, par->in,
+ ip6t_log_packet(net, NFPROTO_IPV6, par->hooknum, skb, par->in,
par->out, &li, loginfo->prefix);
#endif
else
{
const struct xt_nflog_info *info = par->targinfo;
struct nf_loginfo li;
+ struct net *net = dev_net(par->in ? par->in : par->out);
li.type = NF_LOG_TYPE_ULOG;
li.u.ulog.copy_len = info->len;
li.u.ulog.group = info->group;
li.u.ulog.qthreshold = info->threshold;
- nfulnl_log_packet(par->family, par->hooknum, skb, par->in,
+ nfulnl_log_packet(net, par->family, par->hooknum, skb, par->in,
par->out, &li, info->prefix);
return XT_CONTINUE;
}
static unsigned int
tcpoptstrip_mangle_packet(struct sk_buff *skb,
- const struct xt_tcpoptstrip_target_info *info,
+ const struct xt_action_param *par,
unsigned int tcphoff, unsigned int minlen)
{
+ const struct xt_tcpoptstrip_target_info *info = par->targinfo;
unsigned int optl, i, j;
struct tcphdr *tcph;
u_int16_t n, o;
u_int8_t *opt;
+ int len;
+
+ /* This is a fragment, no TCP header is available */
+ if (par->fragoff != 0)
+ return XT_CONTINUE;
if (!skb_make_writable(skb, skb->len))
return NF_DROP;
+ len = skb->len - tcphoff;
+ if (len < (int)sizeof(struct tcphdr) ||
+ tcp_hdr(skb)->doff * 4 > len)
+ return NF_DROP;
+
tcph = (struct tcphdr *)(skb_network_header(skb) + tcphoff);
opt = (u_int8_t *)tcph;
static unsigned int
tcpoptstrip_tg4(struct sk_buff *skb, const struct xt_action_param *par)
{
- return tcpoptstrip_mangle_packet(skb, par->targinfo, ip_hdrlen(skb),
+ return tcpoptstrip_mangle_packet(skb, par, ip_hdrlen(skb),
sizeof(struct iphdr) + sizeof(struct tcphdr));
}
if (tcphoff < 0)
return NF_DROP;
- return tcpoptstrip_mangle_packet(skb, par->targinfo, tcphoff,
+ return tcpoptstrip_mangle_packet(skb, par, tcphoff,
sizeof(*ipv6h) + sizeof(struct tcphdr));
}
#endif
#include <net/ip6_fib.h>
#endif
+#include <linux/netfilter_ipv6.h>
#include <linux/netfilter/xt_addrtype.h>
#include <linux/netfilter/x_tables.h>
#if IS_ENABLED(CONFIG_IP6_NF_IPTABLES)
static u32 match_lookup_rt6(struct net *net, const struct net_device *dev,
- const struct in6_addr *addr)
+ const struct in6_addr *addr, u16 mask)
{
const struct nf_afinfo *afinfo;
struct flowi6 flow;
struct rt6_info *rt;
- u32 ret;
+ u32 ret = 0;
int route_err;
memset(&flow, 0, sizeof(flow));
rcu_read_lock();
afinfo = nf_get_afinfo(NFPROTO_IPV6);
- if (afinfo != NULL)
+ if (afinfo != NULL) {
+ const struct nf_ipv6_ops *v6ops;
+
+ if (dev && (mask & XT_ADDRTYPE_LOCAL)) {
+ v6ops = nf_get_ipv6_ops();
+ if (v6ops && v6ops->chk_addr(net, addr, dev, true))
+ ret = XT_ADDRTYPE_LOCAL;
+ }
route_err = afinfo->route(net, (struct dst_entry **)&rt,
- flowi6_to_flowi(&flow), !!dev);
- else
+ flowi6_to_flowi(&flow), false);
+ } else {
route_err = 1;
-
+ }
rcu_read_unlock();
if (route_err)
if (rt->rt6i_flags & RTF_REJECT)
ret = XT_ADDRTYPE_UNREACHABLE;
- else
- ret = 0;
- if (rt->rt6i_flags & RTF_LOCAL)
+ if (dev == NULL && rt->rt6i_flags & RTF_LOCAL)
ret |= XT_ADDRTYPE_LOCAL;
if (rt->rt6i_flags & RTF_ANYCAST)
ret |= XT_ADDRTYPE_ANYCAST;
-
dst_release(&rt->dst);
return ret;
}
if ((XT_ADDRTYPE_LOCAL | XT_ADDRTYPE_ANYCAST |
XT_ADDRTYPE_UNREACHABLE) & mask)
- return !!(mask & match_lookup_rt6(net, dev, addr));
+ return !!(mask & match_lookup_rt6(net, dev, addr, mask));
return true;
}
}
}
+/**
+ * netlbl_domhsh_validate - Validate a new domain mapping entry
+ * @entry: the entry to validate
+ *
+ * This function validates the new domain mapping entry to ensure that it is
+ * a valid entry. Returns zero on success, negative values on failure.
+ *
+ */
+static int netlbl_domhsh_validate(const struct netlbl_dom_map *entry)
+{
+ struct netlbl_af4list *iter4;
+ struct netlbl_domaddr4_map *map4;
+#if IS_ENABLED(CONFIG_IPV6)
+ struct netlbl_af6list *iter6;
+ struct netlbl_domaddr6_map *map6;
+#endif /* IPv6 */
+
+ if (entry == NULL)
+ return -EINVAL;
+
+ switch (entry->type) {
+ case NETLBL_NLTYPE_UNLABELED:
+ if (entry->type_def.cipsov4 != NULL ||
+ entry->type_def.addrsel != NULL)
+ return -EINVAL;
+ break;
+ case NETLBL_NLTYPE_CIPSOV4:
+ if (entry->type_def.cipsov4 == NULL)
+ return -EINVAL;
+ break;
+ case NETLBL_NLTYPE_ADDRSELECT:
+ netlbl_af4list_foreach(iter4, &entry->type_def.addrsel->list4) {
+ map4 = netlbl_domhsh_addr4_entry(iter4);
+ switch (map4->type) {
+ case NETLBL_NLTYPE_UNLABELED:
+ if (map4->type_def.cipsov4 != NULL)
+ return -EINVAL;
+ break;
+ case NETLBL_NLTYPE_CIPSOV4:
+ if (map4->type_def.cipsov4 == NULL)
+ return -EINVAL;
+ break;
+ default:
+ return -EINVAL;
+ }
+ }
+#if IS_ENABLED(CONFIG_IPV6)
+ netlbl_af6list_foreach(iter6, &entry->type_def.addrsel->list6) {
+ map6 = netlbl_domhsh_addr6_entry(iter6);
+ switch (map6->type) {
+ case NETLBL_NLTYPE_UNLABELED:
+ break;
+ default:
+ return -EINVAL;
+ }
+ }
+#endif /* IPv6 */
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
/*
* Domain Hash Table Functions
*/
struct netlbl_af6list *tmp6;
#endif /* IPv6 */
+ ret_val = netlbl_domhsh_validate(entry);
+ if (ret_val != 0)
+ return ret_val;
+
/* XXX - we can remove this RCU read lock as the spinlock protects the
* entire function, but before we do we need to fixup the
* netlbl_af[4,6]list RCU functions to do "the right thing" with
atomic_dec(&ring->pending);
sock_put(sk);
- skb->data = NULL;
+ skb->head = NULL;
}
#endif
if (skb->sk != NULL)
obj-$(CONFIG_NFC) += nfc.o
obj-$(CONFIG_NFC_NCI) += nci/
obj-$(CONFIG_NFC_HCI) += hci/
-#obj-$(CONFIG_NFC_LLCP) += llcp/
nfc-objs := core.o netlink.o af_nfc.o rawsock.o llcp_core.o llcp_commands.o \
llcp_sock.o
}
if (R_tab) {
police->rate_present = true;
- psched_ratecfg_precompute(&police->rate, R_tab->rate.rate);
+ psched_ratecfg_precompute(&police->rate, &R_tab->rate);
qdisc_put_rtab(R_tab);
} else {
police->rate_present = false;
}
if (P_tab) {
police->peak_present = true;
- psched_ratecfg_precompute(&police->peak, P_tab->rate.rate);
+ psched_ratecfg_precompute(&police->peak, &P_tab->rate);
qdisc_put_rtab(P_tab);
} else {
police->peak_present = false;
};
if (police->rate_present)
- opt.rate.rate = psched_ratecfg_getrate(&police->rate);
+ psched_ratecfg_getrate(&opt.rate, &police->rate);
if (police->peak_present)
- opt.peakrate.rate = psched_ratecfg_getrate(&police->peak);
+ psched_ratecfg_getrate(&opt.peakrate, &police->peak);
if (nla_put(skb, TCA_POLICE_TBF, sizeof(opt), &opt))
goto nla_put_failure;
if (police->tcfp_result &&
WARN_ON(timer_pending(&dev->watchdog_timer));
}
-void psched_ratecfg_precompute(struct psched_ratecfg *r, u32 rate)
+void psched_ratecfg_precompute(struct psched_ratecfg *r,
+ const struct tc_ratespec *conf)
{
u64 factor;
u64 mult;
int shift;
- r->rate_bps = (u64)rate << 3;
- r->shift = 0;
+ memset(r, 0, sizeof(*r));
+ r->overhead = conf->overhead;
+ r->rate_bps = (u64)conf->rate << 3;
r->mult = 1;
/*
* Calibrate mult, shift so that token counting is accurate
} un;
struct rb_node node[TC_HTB_NUMPRIO]; /* node for self or feed tree */
struct rb_node pq_node; /* node for event queue */
- psched_time_t pq_key;
+ s64 pq_key;
int prio_activity; /* for which prios are we active */
enum htb_cmode cmode; /* current mode of the class */
/* token bucket parameters */
struct psched_ratecfg rate;
struct psched_ratecfg ceil;
- s64 buffer, cbuffer; /* token bucket depth/rate */
- psched_tdiff_t mbuffer; /* max wait time */
- s64 tokens, ctokens; /* current number of tokens */
- psched_time_t t_c; /* checkpoint time */
+ s64 buffer, cbuffer; /* token bucket depth/rate */
+ s64 mbuffer; /* max wait time */
+ s64 tokens, ctokens; /* current number of tokens */
+ s64 t_c; /* checkpoint time */
};
struct htb_sched {
struct rb_root wait_pq[TC_HTB_MAXDEPTH];
/* time of nearest event per level (row) */
- psched_time_t near_ev_cache[TC_HTB_MAXDEPTH];
+ s64 near_ev_cache[TC_HTB_MAXDEPTH];
int defcls; /* class where unclassified flows go to */
/* filters for qdisc itself */
struct tcf_proto *filter_list;
- int rate2quantum; /* quant = rate / rate2quantum */
- psched_time_t now; /* cached dequeue time */
+ int rate2quantum; /* quant = rate / rate2quantum */
+ s64 now; /* cached dequeue time */
struct qdisc_watchdog watchdog;
/* non shaped skbs; let them go directly thru */
* next pending event (0 for no event in pq, q->now for too many events).
* Note: Applied are events whose have cl->pq_key <= q->now.
*/
-static psched_time_t htb_do_events(struct htb_sched *q, int level,
- unsigned long start)
+static s64 htb_do_events(struct htb_sched *q, int level,
+ unsigned long start)
{
/* don't run for longer than 2 jiffies; 2 is used instead of
* 1 to simplify things when jiffy is going to be incremented
struct sk_buff *skb;
struct htb_sched *q = qdisc_priv(sch);
int level;
- psched_time_t next_event;
+ s64 next_event;
unsigned long start_at;
/* try to dequeue direct packets as high prio (!) to minimize cpu work */
for (level = 0; level < TC_HTB_MAXDEPTH; level++) {
/* common case optimization - skip event handler quickly */
int m;
- psched_time_t event;
+ s64 event;
if (q->now >= q->near_ev_cache[level]) {
event = htb_do_events(q, level, start_at);
memset(&opt, 0, sizeof(opt));
- opt.rate.rate = psched_ratecfg_getrate(&cl->rate);
+ psched_ratecfg_getrate(&opt.rate, &cl->rate);
opt.buffer = PSCHED_NS2TICKS(cl->buffer);
- opt.ceil.rate = psched_ratecfg_getrate(&cl->ceil);
+ psched_ratecfg_getrate(&opt.ceil, &cl->ceil);
opt.cbuffer = PSCHED_NS2TICKS(cl->cbuffer);
opt.quantum = cl->quantum;
opt.prio = cl->prio;
if (!cl->level && cl->un.leaf.q)
cl->qstats.qlen = cl->un.leaf.q->q.qlen;
- cl->xstats.tokens = cl->tokens;
- cl->xstats.ctokens = cl->ctokens;
+ cl->xstats.tokens = PSCHED_NS2TICKS(cl->tokens);
+ cl->xstats.ctokens = PSCHED_NS2TICKS(cl->ctokens);
if (gnet_stats_copy_basic(d, &cl->bstats) < 0 ||
gnet_stats_copy_rate_est(d, NULL, &cl->rate_est) < 0 ||
parent->un.leaf.q = new_q ? new_q : &noop_qdisc;
parent->tokens = parent->buffer;
parent->ctokens = parent->cbuffer;
- parent->t_c = psched_get_time();
+ parent->t_c = ktime_to_ns(ktime_get());
parent->cmode = HTB_CAN_SEND;
}
/* set class to be in HTB_CAN_SEND state */
cl->tokens = PSCHED_TICKS2NS(hopt->buffer);
cl->ctokens = PSCHED_TICKS2NS(hopt->cbuffer);
- cl->mbuffer = 60 * PSCHED_TICKS_PER_SEC; /* 1min */
- cl->t_c = psched_get_time();
+ cl->mbuffer = 60ULL * NSEC_PER_SEC; /* 1min */
+ cl->t_c = ktime_to_ns(ktime_get());
cl->cmode = HTB_CAN_SEND;
/* attach to the hash list and parent's family */
cl->prio = TC_HTB_NUMPRIO - 1;
}
- psched_ratecfg_precompute(&cl->rate, hopt->rate.rate);
- psched_ratecfg_precompute(&cl->ceil, hopt->ceil.rate);
+ psched_ratecfg_precompute(&cl->rate, &hopt->rate);
+ psched_ratecfg_precompute(&cl->ceil, &hopt->ceil);
cl->buffer = PSCHED_TICKS2NS(hopt->buffer);
cl->cbuffer = PSCHED_TICKS2NS(hopt->buffer);
q->tokens = q->buffer;
q->ptokens = q->mtu;
- psched_ratecfg_precompute(&q->rate, rtab->rate.rate);
+ psched_ratecfg_precompute(&q->rate, &rtab->rate);
if (ptab) {
- psched_ratecfg_precompute(&q->peak, ptab->rate.rate);
+ psched_ratecfg_precompute(&q->peak, &ptab->rate);
q->peak_present = true;
} else {
q->peak_present = false;
goto nla_put_failure;
opt.limit = q->limit;
- opt.rate.rate = psched_ratecfg_getrate(&q->rate);
+ psched_ratecfg_getrate(&opt.rate, &q->rate);
if (q->peak_present)
- opt.peakrate.rate = psched_ratecfg_getrate(&q->peak);
+ psched_ratecfg_getrate(&opt.peakrate, &q->peak);
else
memset(&opt.peakrate, 0, sizeof(opt.peakrate));
opt.mtu = PSCHED_NS2TICKS(q->mtu);
unsigned int name_len;
};
-static int __sys_sendmsg(struct socket *sock, struct msghdr __user *msg,
+static int ___sys_sendmsg(struct socket *sock, struct msghdr __user *msg,
struct msghdr *msg_sys, unsigned int flags,
struct used_address *used_address)
{
* BSD sendmsg interface
*/
-SYSCALL_DEFINE3(sendmsg, int, fd, struct msghdr __user *, msg, unsigned int, flags)
+long __sys_sendmsg(int fd, struct msghdr __user *msg, unsigned flags)
{
int fput_needed, err;
struct msghdr msg_sys;
- struct socket *sock = sockfd_lookup_light(fd, &err, &fput_needed);
+ struct socket *sock;
+ sock = sockfd_lookup_light(fd, &err, &fput_needed);
if (!sock)
goto out;
- err = __sys_sendmsg(sock, msg, &msg_sys, flags, NULL);
+ err = ___sys_sendmsg(sock, msg, &msg_sys, flags, NULL);
fput_light(sock->file, fput_needed);
out:
return err;
}
+SYSCALL_DEFINE3(sendmsg, int, fd, struct msghdr __user *, msg, unsigned int, flags)
+{
+ if (flags & MSG_CMSG_COMPAT)
+ return -EINVAL;
+ return __sys_sendmsg(fd, msg, flags);
+}
+
/*
* Linux sendmmsg interface
*/
while (datagrams < vlen) {
if (MSG_CMSG_COMPAT & flags) {
- err = __sys_sendmsg(sock, (struct msghdr __user *)compat_entry,
- &msg_sys, flags, &used_address);
+ err = ___sys_sendmsg(sock, (struct msghdr __user *)compat_entry,
+ &msg_sys, flags, &used_address);
if (err < 0)
break;
err = __put_user(err, &compat_entry->msg_len);
++compat_entry;
} else {
- err = __sys_sendmsg(sock, (struct msghdr __user *)entry,
- &msg_sys, flags, &used_address);
+ err = ___sys_sendmsg(sock,
+ (struct msghdr __user *)entry,
+ &msg_sys, flags, &used_address);
if (err < 0)
break;
err = put_user(err, &entry->msg_len);
SYSCALL_DEFINE4(sendmmsg, int, fd, struct mmsghdr __user *, mmsg,
unsigned int, vlen, unsigned int, flags)
{
+ if (flags & MSG_CMSG_COMPAT)
+ return -EINVAL;
return __sys_sendmmsg(fd, mmsg, vlen, flags);
}
-static int __sys_recvmsg(struct socket *sock, struct msghdr __user *msg,
+static int ___sys_recvmsg(struct socket *sock, struct msghdr __user *msg,
struct msghdr *msg_sys, unsigned int flags, int nosec)
{
struct compat_msghdr __user *msg_compat =
* BSD recvmsg interface
*/
-SYSCALL_DEFINE3(recvmsg, int, fd, struct msghdr __user *, msg,
- unsigned int, flags)
+long __sys_recvmsg(int fd, struct msghdr __user *msg, unsigned flags)
{
int fput_needed, err;
struct msghdr msg_sys;
- struct socket *sock = sockfd_lookup_light(fd, &err, &fput_needed);
+ struct socket *sock;
+ sock = sockfd_lookup_light(fd, &err, &fput_needed);
if (!sock)
goto out;
- err = __sys_recvmsg(sock, msg, &msg_sys, flags, 0);
+ err = ___sys_recvmsg(sock, msg, &msg_sys, flags, 0);
fput_light(sock->file, fput_needed);
out:
return err;
}
+SYSCALL_DEFINE3(recvmsg, int, fd, struct msghdr __user *, msg,
+ unsigned int, flags)
+{
+ if (flags & MSG_CMSG_COMPAT)
+ return -EINVAL;
+ return __sys_recvmsg(fd, msg, flags);
+}
+
/*
* Linux recvmmsg interface
*/
* No need to ask LSM for more than the first datagram.
*/
if (MSG_CMSG_COMPAT & flags) {
- err = __sys_recvmsg(sock, (struct msghdr __user *)compat_entry,
- &msg_sys, flags & ~MSG_WAITFORONE,
- datagrams);
+ err = ___sys_recvmsg(sock, (struct msghdr __user *)compat_entry,
+ &msg_sys, flags & ~MSG_WAITFORONE,
+ datagrams);
if (err < 0)
break;
err = __put_user(err, &compat_entry->msg_len);
++compat_entry;
} else {
- err = __sys_recvmsg(sock, (struct msghdr __user *)entry,
- &msg_sys, flags & ~MSG_WAITFORONE,
- datagrams);
+ err = ___sys_recvmsg(sock,
+ (struct msghdr __user *)entry,
+ &msg_sys, flags & ~MSG_WAITFORONE,
+ datagrams);
if (err < 0)
break;
err = put_user(err, &entry->msg_len);
int datagrams;
struct timespec timeout_sys;
+ if (flags & MSG_CMSG_COMPAT)
+ return -EINVAL;
+
if (!timeout)
return __sys_recvmmsg(fd, mmsg, vlen, flags, NULL);
#include <linux/sunrpc/gss_api.h>
#include <asm/uaccess.h>
+#include "../netns.h"
+
static const struct rpc_authops authgss_ops;
static const struct rpc_credops gss_credops;
};
/* pipe_version >= 0 if and only if someone has a pipe open. */
-static int pipe_version = -1;
-static atomic_t pipe_users = ATOMIC_INIT(0);
static DEFINE_SPINLOCK(pipe_version_lock);
static struct rpc_wait_queue pipe_version_rpc_waitqueue;
static DECLARE_WAIT_QUEUE_HEAD(pipe_version_waitqueue);
char databuf[UPCALL_BUF_LEN];
};
-static int get_pipe_version(void)
+static int get_pipe_version(struct net *net)
{
+ struct sunrpc_net *sn = net_generic(net, sunrpc_net_id);
int ret;
spin_lock(&pipe_version_lock);
- if (pipe_version >= 0) {
- atomic_inc(&pipe_users);
- ret = pipe_version;
+ if (sn->pipe_version >= 0) {
+ atomic_inc(&sn->pipe_users);
+ ret = sn->pipe_version;
} else
ret = -EAGAIN;
spin_unlock(&pipe_version_lock);
return ret;
}
-static void put_pipe_version(void)
+static void put_pipe_version(struct net *net)
{
- if (atomic_dec_and_lock(&pipe_users, &pipe_version_lock)) {
- pipe_version = -1;
+ struct sunrpc_net *sn = net_generic(net, sunrpc_net_id);
+
+ if (atomic_dec_and_lock(&sn->pipe_users, &pipe_version_lock)) {
+ sn->pipe_version = -1;
spin_unlock(&pipe_version_lock);
}
}
static void
gss_release_msg(struct gss_upcall_msg *gss_msg)
{
+ struct net *net = rpc_net_ns(gss_msg->auth->client);
if (!atomic_dec_and_test(&gss_msg->count))
return;
- put_pipe_version();
+ put_pipe_version(net);
BUG_ON(!list_empty(&gss_msg->list));
if (gss_msg->ctx != NULL)
gss_put_ctx(gss_msg->ctx);
struct rpc_clnt *clnt,
const char *service_name)
{
- if (pipe_version == 0)
+ struct net *net = rpc_net_ns(clnt);
+ struct sunrpc_net *sn = net_generic(net, sunrpc_net_id);
+
+ if (sn->pipe_version == 0)
gss_encode_v0_msg(gss_msg);
else /* pipe_version == 1 */
gss_encode_v1_msg(gss_msg, clnt, service_name);
gss_msg = kzalloc(sizeof(*gss_msg), GFP_NOFS);
if (gss_msg == NULL)
return ERR_PTR(-ENOMEM);
- vers = get_pipe_version();
+ vers = get_pipe_version(rpc_net_ns(clnt));
if (vers < 0) {
kfree(gss_msg);
return ERR_PTR(vers);
static inline int
gss_create_upcall(struct gss_auth *gss_auth, struct gss_cred *gss_cred)
{
+ struct net *net = rpc_net_ns(gss_auth->client);
+ struct sunrpc_net *sn = net_generic(net, sunrpc_net_id);
struct rpc_pipe *pipe;
struct rpc_cred *cred = &gss_cred->gc_base;
struct gss_upcall_msg *gss_msg;
+ unsigned long timeout;
DEFINE_WAIT(wait);
- int err = 0;
+ int err;
dprintk("RPC: %s for uid %u\n",
__func__, from_kuid(&init_user_ns, cred->cr_uid));
retry:
+ err = 0;
+ /* Default timeout is 15s unless we know that gssd is not running */
+ timeout = 15 * HZ;
+ if (!sn->gssd_running)
+ timeout = HZ >> 2;
gss_msg = gss_setup_upcall(gss_auth->client, gss_auth, cred);
if (PTR_ERR(gss_msg) == -EAGAIN) {
err = wait_event_interruptible_timeout(pipe_version_waitqueue,
- pipe_version >= 0, 15*HZ);
- if (pipe_version < 0) {
+ sn->pipe_version >= 0, timeout);
+ if (sn->pipe_version < 0) {
+ if (err == 0)
+ sn->gssd_running = 0;
warn_gssd();
err = -EACCES;
}
- if (err)
+ if (err < 0)
goto out;
goto retry;
}
static int gss_pipe_open(struct inode *inode, int new_version)
{
+ struct net *net = inode->i_sb->s_fs_info;
+ struct sunrpc_net *sn = net_generic(net, sunrpc_net_id);
int ret = 0;
spin_lock(&pipe_version_lock);
- if (pipe_version < 0) {
+ if (sn->pipe_version < 0) {
/* First open of any gss pipe determines the version: */
- pipe_version = new_version;
+ sn->pipe_version = new_version;
rpc_wake_up(&pipe_version_rpc_waitqueue);
wake_up(&pipe_version_waitqueue);
- } else if (pipe_version != new_version) {
+ } else if (sn->pipe_version != new_version) {
/* Trying to open a pipe of a different version */
ret = -EBUSY;
goto out;
}
- atomic_inc(&pipe_users);
+ atomic_inc(&sn->pipe_users);
out:
spin_unlock(&pipe_version_lock);
return ret;
static void
gss_pipe_release(struct inode *inode)
{
+ struct net *net = inode->i_sb->s_fs_info;
struct rpc_pipe *pipe = RPC_I(inode)->pipe;
struct gss_upcall_msg *gss_msg;
}
spin_unlock(&pipe->lock);
- put_pipe_version();
+ put_pipe_version(net);
}
static void
#ifdef CONFIG_PROC_FS
-static bool set_gss_proxy(struct net *net, int type)
+static int set_gss_proxy(struct net *net, int type)
{
struct sunrpc_net *sn = net_generic(net, sunrpc_net_id);
int ret = 0;
return false;
}
-static int wait_for_gss_proxy(struct net *net)
+static int wait_for_gss_proxy(struct net *net, struct file *file)
{
struct sunrpc_net *sn = net_generic(net, sunrpc_net_id);
+ if (file->f_flags & O_NONBLOCK && !gssp_ready(sn))
+ return -EAGAIN;
return wait_event_interruptible(sn->gssp_wq, gssp_ready(sn));
}
size_t len;
int ret;
- ret = wait_for_gss_proxy(net);
+ ret = wait_for_gss_proxy(net, file);
if (ret)
return ret;
wait_queue_head_t gssp_wq;
struct rpc_clnt *gssp_clnt;
int use_gss_proxy;
+ int pipe_version;
+ atomic_t pipe_users;
struct proc_dir_entry *use_gssp_proc;
+
+ unsigned int gssd_running;
};
extern int sunrpc_net_id;
static int
rpc_pipe_open(struct inode *inode, struct file *filp)
{
+ struct net *net = inode->i_sb->s_fs_info;
+ struct sunrpc_net *sn = net_generic(net, sunrpc_net_id);
struct rpc_pipe *pipe;
int first_open;
int res = -ENXIO;
mutex_lock(&inode->i_mutex);
+ sn->gssd_running = 1;
pipe = RPC_I(inode)->pipe;
if (pipe == NULL)
goto out;
struct sunrpc_net *sn = net_generic(net, sunrpc_net_id);
mutex_init(&sn->pipefs_sb_lock);
+ sn->gssd_running = 1;
+ sn->pipe_version = -1;
}
/*
* Note: If the task is ASYNC, and is being made runnable after sitting on an
* rpc_wait_queue, this must be called with the queue spinlock held to protect
* the wait queue operation.
+ * Note the ordering of rpc_test_and_set_running() and rpc_clear_queued(),
+ * which is needed to ensure that __rpc_execute() doesn't loop (due to the
+ * lockless RPC_IS_QUEUED() test) before we've had a chance to test
+ * the RPC_TASK_RUNNING flag.
*/
static void rpc_make_runnable(struct rpc_task *task)
{
+ bool need_wakeup = !rpc_test_and_set_running(task);
+
rpc_clear_queued(task);
- if (rpc_test_and_set_running(task))
+ if (!need_wakeup)
return;
if (RPC_IS_ASYNC(task)) {
INIT_WORK(&task->u.tk_work, rpc_async_schedule);
goto badcred;
argv->iov_base = (void*)((__be32*)argv->iov_base + slen); /* skip machname */
argv->iov_len -= slen*4;
-
+ /*
+ * Note: we skip uid_valid()/gid_valid() checks here for
+ * backwards compatibility with clients that use -1 id's.
+ * Instead, -1 uid or gid is later mapped to the
+ * (export-specific) anonymous id by nfsd_setuser.
+ * Supplementary gid's will be left alone.
+ */
cred->cr_uid = make_kuid(&init_user_ns, svc_getnl(argv)); /* uid */
cred->cr_gid = make_kgid(&init_user_ns, svc_getnl(argv)); /* gid */
- if (!uid_valid(cred->cr_uid) || !gid_valid(cred->cr_gid))
- goto badcred;
slen = svc_getnl(argv); /* gids length */
if (slen > 16 || (len -= (slen + 2)*4) < 0)
goto badcred;
return SVC_CLOSE;
for (i = 0; i < slen; i++) {
kgid_t kgid = make_kgid(&init_user_ns, svc_getnl(argv));
- if (!gid_valid(kgid))
- goto badcred;
GROUP_AT(cred->cr_group_info, i) = kgid;
}
if (svc_getu32(argv) != htonl(RPC_AUTH_NULL) || svc_getu32(argv) != 0) {
* cfg80211_mutex lock
*/
res = rfkill_register(rdev->rfkill);
- if (res)
- goto out_rm_dev;
+ if (res) {
+ device_del(&rdev->wiphy.dev);
+
+ mutex_lock(&cfg80211_mutex);
+ debugfs_remove_recursive(rdev->wiphy.debugfsdir);
+ list_del_rcu(&rdev->list);
+ wiphy_regulatory_deregister(wiphy);
+ mutex_unlock(&cfg80211_mutex);
+ return res;
+ }
rtnl_lock();
rdev->wiphy.registered = true;
rtnl_unlock();
return 0;
-
-out_rm_dev:
- device_del(&rdev->wiphy.dev);
- return res;
}
EXPORT_SYMBOL(wiphy_register);
#endif
__cfg80211_disconnect(rdev, dev,
WLAN_REASON_DEAUTH_LEAVING, true);
- cfg80211_mlme_down(rdev, dev);
wdev_unlock(wdev);
break;
case NL80211_IFTYPE_MESH_POINT:
(u32)sinfo->rx_bytes))
goto nla_put_failure;
if ((sinfo->filled & (STATION_INFO_TX_BYTES |
- NL80211_STA_INFO_TX_BYTES64)) &&
+ STATION_INFO_TX_BYTES64)) &&
nla_put_u32(msg, NL80211_STA_INFO_TX_BYTES,
(u32)sinfo->tx_bytes))
goto nla_put_failure;
&tcp->payload_tok))
return -ENOBUFS;
+ nla_nest_end(msg, nl_tcp);
+
return 0;
}
if (nla_put_u32(msg, NL80211_ATTR_WIPHY, rdev->wiphy_idx) ||
(netdev && nla_put_u32(msg, NL80211_ATTR_IFINDEX,
netdev->ifindex)) ||
+ nla_put_u64(msg, NL80211_ATTR_WDEV, wdev_id(wdev)) ||
nla_put_u32(msg, NL80211_ATTR_WIPHY_FREQ, freq) ||
(sig_dbm &&
nla_put_u32(msg, NL80211_ATTR_RX_SIGNAL_DBM, sig_dbm)) ||
if (nla_put_u32(msg, NL80211_ATTR_WIPHY, rdev->wiphy_idx) ||
(netdev && nla_put_u32(msg, NL80211_ATTR_IFINDEX,
netdev->ifindex)) ||
+ nla_put_u64(msg, NL80211_ATTR_WDEV, wdev_id(wdev)) ||
nla_put(msg, NL80211_ATTR_FRAME, len, buf) ||
nla_put_u64(msg, NL80211_ATTR_COOKIE, cookie) ||
(ack && nla_put_flag(msg, NL80211_ATTR_ACK)))
mutex_lock(&rdev->sched_scan_mtx);
list_for_each_entry(wdev, &rdev->wdev_list, list) {
+ if (!wdev->netdev)
+ continue;
+
wdev_lock(wdev);
if (!netif_running(wdev->netdev)) {
wdev_unlock(wdev);
/* was it connected by userspace SME? */
if (!wdev->conn) {
cfg80211_mlme_down(rdev, dev);
- return 0;
+ goto disconnect;
}
if (wdev->sme_state == CFG80211_SME_CONNECTING &&
return err;
}
+ disconnect:
if (wdev->sme_state == CFG80211_SME_CONNECTED)
__cfg80211_disconnected(dev, NULL, 0, 0, false);
else if (wdev->sme_state == CFG80211_SME_CONNECTING)
TP_STRUCT__entry(
WIPHY_ENTRY
WDEV_ENTRY
+ __field(bool, non_wireless)
__field(bool, disconnect)
__field(bool, magic_pkt)
__field(bool, gtk_rekey_failure)
__field(bool, rfkill_release)
__field(s32, pattern_idx)
__field(u32, packet_len)
- __dynamic_array(u8, packet, wakeup->packet_present_len)
+ __dynamic_array(u8, packet,
+ wakeup ? wakeup->packet_present_len : 0)
),
TP_fast_assign(
WIPHY_ASSIGN;
WDEV_ASSIGN;
- __entry->disconnect = wakeup->disconnect;
- __entry->magic_pkt = wakeup->magic_pkt;
- __entry->gtk_rekey_failure = wakeup->gtk_rekey_failure;
- __entry->eap_identity_req = wakeup->eap_identity_req;
- __entry->four_way_handshake = wakeup->four_way_handshake;
- __entry->rfkill_release = wakeup->rfkill_release;
- __entry->pattern_idx = wakeup->pattern_idx;
- __entry->packet_len = wakeup->packet_len;
- if (wakeup->packet && wakeup->packet_present_len)
+ __entry->non_wireless = !wakeup;
+ __entry->disconnect = wakeup ? wakeup->disconnect : false;
+ __entry->magic_pkt = wakeup ? wakeup->magic_pkt : false;
+ __entry->gtk_rekey_failure = wakeup ? wakeup->gtk_rekey_failure : false;
+ __entry->eap_identity_req = wakeup ? wakeup->eap_identity_req : false;
+ __entry->four_way_handshake = wakeup ? wakeup->four_way_handshake : false;
+ __entry->rfkill_release = wakeup ? wakeup->rfkill_release : false;
+ __entry->pattern_idx = wakeup ? wakeup->pattern_idx : false;
+ __entry->packet_len = wakeup ? wakeup->packet_len : false;
+ if (wakeup && wakeup->packet && wakeup->packet_present_len)
memcpy(__get_dynamic_array(packet), wakeup->packet,
wakeup->packet_present_len);
),
if (unlikely(x->km.state != XFRM_STATE_VALID)) {
XFRM_INC_STATS(net, LINUX_MIB_XFRMOUTSTATEINVALID);
+ err = -EINVAL;
goto error;
}
}
}
-static void xfrm_garbage_collect(struct net *net)
+void xfrm_garbage_collect(struct net *net)
{
flow_cache_flush();
__xfrm_garbage_collect(net);
}
+EXPORT_SYMBOL(xfrm_garbage_collect);
static void xfrm_garbage_collect_deferred(struct net *net)
{
out:
xfrm_pol_put(xp);
+ if (delete && err == 0)
+ xfrm_garbage_collect(net);
return err;
}
quiet_cmd_dtc = DTC $@
cmd_dtc = $(CPP) $(dtc_cpp_flags) -x assembler-with-cpp -o $(dtc-tmp) $< ; \
$(objtree)/scripts/dtc/dtc -O dtb -o $@ -b 0 \
- -i $(srctree)/arch/$(SRCARCH)/boot/dts $(DTC_FLAGS) \
+ -i $(dir $<) $(DTC_FLAGS) \
-d $(depfile).dtc $(dtc-tmp) ; \
cat $(depfile).pre $(depfile).dtc > $(depfile)
;;
--refresh)
;;
- --*-after)
+ --*-after|-E|-D|-M)
checkarg "$1"
A=$ARG
checkarg "$2"
}
}
- if (i < max_choice ||
- key == KEY_UP || key == KEY_DOWN ||
- key == '-' || key == '+' ||
- key == KEY_PPAGE || key == KEY_NPAGE) {
+ if (item_count() != 0 &&
+ (i < max_choice ||
+ key == KEY_UP || key == KEY_DOWN ||
+ key == '-' || key == '+' ||
+ key == KEY_PPAGE || key == KEY_NPAGE)) {
/* Remove highligt of current item */
print_item(scroll + choice, choice, FALSE);
active_menu, &s_scroll);
if (res == 1 || res == KEY_ESC || res == -ERRDISPLAYTOOSMALL)
break;
- if (!item_activate_selected())
- continue;
- if (!item_tag())
- continue;
-
+ if (item_count() != 0) {
+ if (!item_activate_selected())
+ continue;
+ if (!item_tag())
+ continue;
+ }
submenu = item_data();
active_menu = item_data();
if (submenu)
struct menu *menu = current_entry;
while ((menu = menu->parent) != NULL) {
+ struct expr *dup_expr;
+
if (!menu->visibility)
continue;
+ /*
+ * Do not add a reference to the
+ * menu's visibility expression but
+ * use a copy of it. Otherwise the
+ * expression reduction functions
+ * will modify expressions that have
+ * multiple references which can
+ * cause unwanted side effects.
+ */
+ dup_expr = expr_copy(menu->visibility);
+
prop->visible.expr
= expr_alloc_and(prop->visible.expr,
- menu->visibility);
+ dup_expr);
}
}
memcpy(new_ctx, old_ctx, sizeof(*new_ctx));
memcpy(new_ctx->ctx_str, old_ctx->ctx_str, new_ctx->ctx_len);
+ atomic_inc(&selinux_xfrm_refcount);
*new_ctxp = new_ctx;
}
return 0;
*/
void selinux_xfrm_policy_free(struct xfrm_sec_ctx *ctx)
{
+ atomic_dec(&selinux_xfrm_refcount);
kfree(ctx);
}
int selinux_xfrm_policy_delete(struct xfrm_sec_ctx *ctx)
{
const struct task_security_struct *tsec = current_security();
- int rc = 0;
- if (ctx) {
- rc = avc_has_perm(tsec->sid, ctx->ctx_sid,
- SECCLASS_ASSOCIATION,
- ASSOCIATION__SETCONTEXT, NULL);
- if (rc == 0)
- atomic_dec(&selinux_xfrm_refcount);
- }
+ if (!ctx)
+ return 0;
- return rc;
+ return avc_has_perm(tsec->sid, ctx->ctx_sid,
+ SECCLASS_ASSOCIATION, ASSOCIATION__SETCONTEXT,
+ NULL);
}
/*
*/
void selinux_xfrm_state_free(struct xfrm_state *x)
{
- struct xfrm_sec_ctx *ctx = x->security;
- kfree(ctx);
+ atomic_dec(&selinux_xfrm_refcount);
+ kfree(x->security);
}
/*
{
const struct task_security_struct *tsec = current_security();
struct xfrm_sec_ctx *ctx = x->security;
- int rc = 0;
- if (ctx) {
- rc = avc_has_perm(tsec->sid, ctx->ctx_sid,
- SECCLASS_ASSOCIATION,
- ASSOCIATION__SETCONTEXT, NULL);
- if (rc == 0)
- atomic_dec(&selinux_xfrm_refcount);
- }
+ if (!ctx)
+ return 0;
- return rc;
+ return avc_has_perm(tsec->sid, ctx->ctx_sid,
+ SECCLASS_ASSOCIATION, ASSOCIATION__SETCONTEXT,
+ NULL);
}
/*
return;
if (codec->inv_eapd)
enable = !enable;
+ if (spec->keep_eapd_on && !enable)
+ return;
snd_hda_codec_update_cache(codec, pin, 0,
AC_VERB_SET_EAPD_BTLENABLE,
enable ? 0x02 : 0x00);
* independent HP controls
*/
-/* update HP auto-mute state too */
-static void update_hp_automute_hook(struct hda_codec *codec)
-{
- struct hda_gen_spec *spec = codec->spec;
-
- if (spec->hp_automute_hook)
- spec->hp_automute_hook(codec, NULL);
- else
- snd_hda_gen_hp_automute(codec, NULL);
-}
-
+static void call_hp_automute(struct hda_codec *codec, struct hda_jack_tbl *jack);
static int indep_hp_info(struct snd_kcontrol *kcontrol,
struct snd_ctl_elem_info *uinfo)
{
else
*dacp = spec->alt_dac_nid;
- update_hp_automute_hook(codec);
+ call_hp_automute(codec, NULL);
ret = 1;
}
unlock:
else
val = PIN_HP;
set_pin_target(codec, pin, val, true);
- update_hp_automute_hook(codec);
+ call_hp_automute(codec, NULL);
}
}
val = snd_hda_get_default_vref(codec, nid);
}
snd_hda_set_pin_ctl_cache(codec, nid, val);
- update_hp_automute_hook(codec);
+ call_hp_automute(codec, NULL);
return 1;
}
}
EXPORT_SYMBOL_HDA(snd_hda_gen_mic_autoswitch);
-/* update jack retasking */
-static void update_automute_all(struct hda_codec *codec)
+/* call appropriate hooks */
+static void call_hp_automute(struct hda_codec *codec, struct hda_jack_tbl *jack)
{
struct hda_gen_spec *spec = codec->spec;
+ if (spec->hp_automute_hook)
+ spec->hp_automute_hook(codec, jack);
+ else
+ snd_hda_gen_hp_automute(codec, jack);
+}
- update_hp_automute_hook(codec);
+static void call_line_automute(struct hda_codec *codec,
+ struct hda_jack_tbl *jack)
+{
+ struct hda_gen_spec *spec = codec->spec;
if (spec->line_automute_hook)
- spec->line_automute_hook(codec, NULL);
+ spec->line_automute_hook(codec, jack);
else
- snd_hda_gen_line_automute(codec, NULL);
+ snd_hda_gen_line_automute(codec, jack);
+}
+
+static void call_mic_autoswitch(struct hda_codec *codec,
+ struct hda_jack_tbl *jack)
+{
+ struct hda_gen_spec *spec = codec->spec;
if (spec->mic_autoswitch_hook)
- spec->mic_autoswitch_hook(codec, NULL);
+ spec->mic_autoswitch_hook(codec, jack);
else
- snd_hda_gen_mic_autoswitch(codec, NULL);
+ snd_hda_gen_mic_autoswitch(codec, jack);
+}
+
+/* update jack retasking */
+static void update_automute_all(struct hda_codec *codec)
+{
+ call_hp_automute(codec, NULL);
+ call_line_automute(codec, NULL);
+ call_mic_autoswitch(codec, NULL);
}
/*
snd_printdd("hda-codec: Enable HP auto-muting on NID 0x%x\n",
nid);
snd_hda_jack_detect_enable_callback(codec, nid, HDA_GEN_HP_EVENT,
- spec->hp_automute_hook ?
- spec->hp_automute_hook :
- snd_hda_gen_hp_automute);
+ call_hp_automute);
spec->detect_hp = 1;
}
snd_printdd("hda-codec: Enable Line-Out auto-muting on NID 0x%x\n", nid);
snd_hda_jack_detect_enable_callback(codec, nid,
HDA_GEN_FRONT_EVENT,
- spec->line_automute_hook ?
- spec->line_automute_hook :
- snd_hda_gen_line_automute);
+ call_line_automute);
spec->detect_lo = 1;
}
spec->automute_lo_possible = spec->detect_hp;
snd_hda_jack_detect_enable_callback(codec,
spec->am_entry[i].pin,
HDA_GEN_MIC_EVENT,
- spec->mic_autoswitch_hook ?
- spec->mic_autoswitch_hook :
- snd_hda_gen_mic_autoswitch);
+ call_mic_autoswitch);
return true;
}
unsigned int multi_cap_vol:1; /* allow multiple capture xxx volumes */
unsigned int inv_dmic_split:1; /* inverted dmic w/a for conexant */
unsigned int own_eapd_ctl:1; /* set EAPD by own function */
+ unsigned int keep_eapd_on:1; /* don't turn off EAPD automatically */
unsigned int vmaster_mute_enum:1; /* add vmaster mute mode enum */
unsigned int indep_hp:1; /* independent HP supported */
unsigned int prefer_hp_amp:1; /* enable HP amp for speaker if any */
SND_PCI_QUIRK(0x1028, 0x05f4, "Dell", ALC269_FIXUP_DELL1_MIC_NO_PRESENCE),
SND_PCI_QUIRK(0x1028, 0x05f5, "Dell", ALC269_FIXUP_DELL1_MIC_NO_PRESENCE),
SND_PCI_QUIRK(0x1028, 0x05f6, "Dell", ALC269_FIXUP_DELL1_MIC_NO_PRESENCE),
+ SND_PCI_QUIRK(0x1028, 0x05f8, "Dell", ALC269_FIXUP_DELL1_MIC_NO_PRESENCE),
+ SND_PCI_QUIRK(0x1028, 0x0609, "Dell", ALC269_FIXUP_DELL1_MIC_NO_PRESENCE),
SND_PCI_QUIRK(0x103c, 0x1586, "HP", ALC269_FIXUP_HP_MUTE_LED_MIC2),
SND_PCI_QUIRK(0x103c, 0x18e6, "HP", ALC269_FIXUP_HP_GPIO_LED),
SND_PCI_QUIRK(0x103c, 0x1973, "HP Pavilion", ALC269_FIXUP_HP_MUTE_LED_MIC1),
SND_PCI_QUIRK(0x17aa, 0x21fa, "Thinkpad X230", ALC269_FIXUP_LENOVO_DOCK),
SND_PCI_QUIRK(0x17aa, 0x21f3, "Thinkpad T430", ALC269_FIXUP_LENOVO_DOCK),
SND_PCI_QUIRK(0x17aa, 0x21fb, "Thinkpad T430s", ALC269_FIXUP_LENOVO_DOCK),
+ SND_PCI_QUIRK(0x17aa, 0x2208, "Thinkpad T431s", ALC269_FIXUP_LENOVO_DOCK),
SND_PCI_QUIRK(0x17aa, 0x2203, "Thinkpad X230 Tablet", ALC269_FIXUP_LENOVO_DOCK),
SND_PCI_QUIRK(0x17aa, 0x3bf8, "Quanta FL1", ALC269_FIXUP_PCM_44K),
SND_PCI_QUIRK(0x17aa, 0x9e54, "LENOVO NB", ALC269_FIXUP_LENOVO_EAPD),
spec->codec_type = VT1708S;
spec->no_pin_power_ctl = 1;
spec->gen.indep_hp = 1;
+ spec->gen.keep_eapd_on = 1;
spec->gen.pcm_playback_hook = via_playback_pcm_hook;
return spec;
}
static void set_widgets_power_state(struct hda_codec *codec)
{
+#if 0 /* FIXME: the assumed connections don't match always with the
+ * actual routes by the generic parser, so better to disable
+ * the control for safety.
+ */
struct via_spec *spec = codec->spec;
if (spec->set_widgets_power_state)
spec->set_widgets_power_state(codec);
+#endif
}
static void update_power_state(struct hda_codec *codec, hda_nid_t nid,
/* Fix pop noise on headphones */
int i;
for (i = 0; i < spec->gen.autocfg.hp_outs; i++)
- snd_hda_set_pin_ctl(codec, spec->gen.autocfg.hp_pins[i], 0);
+ snd_hda_codec_write(codec, spec->gen.autocfg.hp_pins[i],
+ 0, AC_VERB_SET_PIN_WIDGET_CONTROL,
+ 0x00);
}
return 0;
if (rc)
goto error_out;
- if (pci_set_dma_mask(pci, DMA_BIT_MASK(30)) < 0) {
+ rc = pci_set_dma_mask(pci, DMA_BIT_MASK(30));
+ if (rc < 0) {
dev_err(&pci->dev, "architecture does not support 30-bit PCI busmaster DMA");
goto error_out_enabled;
}
{ CS42L52_BEEP_VOL, 0x00 }, /* r1D Beep Volume off Time */
{ CS42L52_BEEP_TONE_CTL, 0x00 }, /* r1E Beep Tone Cfg. */
{ CS42L52_TONE_CTL, 0x00 }, /* r1F Tone Ctl */
- { CS42L52_MASTERA_VOL, 0x88 }, /* r20 Master A Volume */
+ { CS42L52_MASTERA_VOL, 0x00 }, /* r20 Master A Volume */
{ CS42L52_MASTERB_VOL, 0x00 }, /* r21 Master B Volume */
{ CS42L52_HPA_VOL, 0x00 }, /* r22 Headphone A Volume */
{ CS42L52_HPB_VOL, 0x00 }, /* r23 Headphone B Volume */
};
static const struct soc_enum mic_bias_level_enum =
- SOC_ENUM_SINGLE(CS42L52_IFACE_CTL1, 0,
+ SOC_ENUM_SINGLE(CS42L52_IFACE_CTL2, 0,
ARRAY_SIZE(mic_bias_level_text), mic_bias_level_text);
static const char * const cs42l52_mic_text[] = { "Single", "Differential" };
SOC_ENUM("Headphone Analog Gain", hp_gain_enum),
SOC_DOUBLE_R_SX_TLV("Speaker Volume", CS42L52_SPKA_VOL,
- CS42L52_SPKB_VOL, 7, 0x1, 0xff, hl_tlv),
+ CS42L52_SPKB_VOL, 0, 0x1, 0xff, hl_tlv),
SOC_DOUBLE_R_SX_TLV("Bypass Volume", CS42L52_PASSTHRUA_VOL,
CS42L52_PASSTHRUB_VOL, 6, 0x18, 0x90, pga_tlv),
SOC_DOUBLE_R_SX_TLV("PCM Mixer Volume",
CS42L52_PCMA_MIXER_VOL, CS42L52_PCMB_MIXER_VOL,
- 6, 0x7f, 0x19, hl_tlv),
+ 0, 0x7f, 0x19, hl_tlv),
SOC_DOUBLE_R("PCM Mixer Switch",
CS42L52_PCMA_MIXER_VOL, CS42L52_PCMB_MIXER_VOL, 7, 1, 1),
#define CS42L52_PB_CTL1_INV_PCMA (1 << 2)
#define CS42L52_PB_CTL1_MSTB_MUTE (1 << 1)
#define CS42L52_PB_CTL1_MSTA_MUTE (1 << 0)
-#define CS42L52_PB_CTL1_MUTE_MASK 0xFFFD
+#define CS42L52_PB_CTL1_MUTE_MASK 0x03
#define CS42L52_PB_CTL1_MUTE 3
#define CS42L52_PB_CTL1_UNMUTE 0
dev_dbg(codec->dev, "irq = %d\n", max98090->irq);
ret = request_threaded_irq(max98090->irq, NULL,
- max98090_interrupt, IRQF_TRIGGER_FALLING,
+ max98090_interrupt, IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
"max98090_interrupt", codec);
if (ret < 0) {
dev_err(codec->dev, "request_irq failed: %d\n",
ARIZONA_MIXER_CONTROLS("DSP3L", ARIZONA_DSP3LMIX_INPUT_1_SOURCE),
ARIZONA_MIXER_CONTROLS("DSP3R", ARIZONA_DSP3RMIX_INPUT_1_SOURCE),
ARIZONA_MIXER_CONTROLS("DSP4L", ARIZONA_DSP4LMIX_INPUT_1_SOURCE),
-ARIZONA_MIXER_CONTROLS("DSP5R", ARIZONA_DSP4RMIX_INPUT_1_SOURCE),
+ARIZONA_MIXER_CONTROLS("DSP4R", ARIZONA_DSP4RMIX_INPUT_1_SOURCE),
ARIZONA_MIXER_CONTROLS("Mic", ARIZONA_MICMIX_INPUT_1_SOURCE),
ARIZONA_MIXER_CONTROLS("Noise", ARIZONA_NOISEMIX_INPUT_1_SOURCE),
if (ret != 0)
return ret;
+ arizona_init_spk(codec);
+
snd_soc_dapm_disable_pin(&codec->dapm, "HAPTICS");
priv->core.arizona->dapm = &codec->dapm;
struct wm8994_priv *wm8994 = snd_soc_codec_get_drvdata(codec);
int drc = wm8994_get_drc(kcontrol->id.name);
+ if (drc < 0)
+ return drc;
ucontrol->value.enumerated.item[0] = wm8994->drc_cfg[drc];
return 0;
struct wm8994_priv *wm8994 = snd_soc_codec_get_drvdata(codec);
int block = wm8994_get_retune_mobile_block(kcontrol->id.name);
+ if (block < 0)
+ return block;
+
ucontrol->value.enumerated.item[0] = wm8994->retune_mobile_cfg[block];
return 0;
{
struct snd_soc_codec *codec = w->codec;
struct wm8994_priv *wm8994 = snd_soc_codec_get_drvdata(codec);
- struct wm8994 *control = codec->control_data;
+ struct wm8994 *control = wm8994->wm8994;
int mask = WM8994_AIF1DAC1L_ENA | WM8994_AIF1DAC1R_ENA;
int i;
int dac;
dev_dbg(codec->dev, "Ignoring removed jack\n");
return IRQ_HANDLED;
}
+ } else if (!(reg & WM8958_MICD_STS)) {
+ snd_soc_jack_report(wm8994->micdet[0].jack, 0,
+ SND_JACK_MECHANICAL | SND_JACK_HEADSET |
+ wm8994->btn_mask);
+ goto out;
}
if (wm8994->mic_detecting)
int word_length)
{
u32 fmt;
- u32 rotate = (word_length / 4) & 0x7;
+ u32 tx_rotate = (word_length / 4) & 0x7;
+ u32 rx_rotate = (32 - word_length) / 4;
u32 mask = (1ULL << word_length) - 1;
/*
mcasp_mod_bits(dev->base + DAVINCI_MCASP_TXFMT_REG,
TXSSZ(fmt), TXSSZ(0x0F));
mcasp_mod_bits(dev->base + DAVINCI_MCASP_TXFMT_REG,
- TXROT(rotate), TXROT(7));
+ TXROT(tx_rotate), TXROT(7));
mcasp_mod_bits(dev->base + DAVINCI_MCASP_RXFMT_REG,
- RXROT(rotate), RXROT(7));
+ RXROT(rx_rotate), RXROT(7));
mcasp_set_reg(dev->base + DAVINCI_MCASP_RXMASK_REG,
mask);
}
goto err;
}
- snd_soc_dapm_stream_event(rtd, SNDRV_PCM_STREAM_PLAYBACK,
- SND_SOC_DAPM_STREAM_START);
+ if (cstream->direction == SND_COMPRESS_PLAYBACK)
+ snd_soc_dapm_stream_event(rtd, SNDRV_PCM_STREAM_PLAYBACK,
+ SND_SOC_DAPM_STREAM_START);
+ else
+ snd_soc_dapm_stream_event(rtd, SNDRV_PCM_STREAM_CAPTURE,
+ SND_SOC_DAPM_STREAM_START);
/* cancel any delayed stream shutdown that is pending */
rtd->pop_wait = 0;
0x94, 0x01, 0x5c, 0x02 /* alt 3: 404 EP2 and 604 EP6 (25 fpp) */
};
-static const u8 known_fw_versions[][4] = {
- { 0x03, 0x01, 0x0b, 0x00 }
+static const u8 known_fw_versions[][2] = {
+ { 0x03, 0x01 }
};
struct ihex_record {
int i;
for (i = 0; i < ARRAY_SIZE(known_fw_versions); i++)
- if (!memcmp(version, known_fw_versions + i, 4))
+ if (!memcmp(version, known_fw_versions + i, 2))
return 0;
snd_printk(KERN_ERR PREFIX "invalid fimware version in device: %*ph. "
case USB_ID(0x046d, 0x0808):
case USB_ID(0x046d, 0x0809):
case USB_ID(0x046d, 0x081d): /* HD Webcam c510 */
+ case USB_ID(0x046d, 0x0825): /* HD Webcam c270 */
case USB_ID(0x046d, 0x0991):
/* Most audio usb devices lie about volume resolution.
* Most Logitech webcams have res = 384.
.bInterfaceSubClass = USB_SUBCLASS_AUDIOCONTROL
},
{
- USB_DEVICE(0x046d, 0x0990),
+ .match_flags = USB_DEVICE_ID_MATCH_DEVICE |
+ USB_DEVICE_ID_MATCH_INT_CLASS |
+ USB_DEVICE_ID_MATCH_INT_SUBCLASS,
+ .idVendor = 0x046d,
+ .idProduct = 0x0990,
+ .bInterfaceClass = USB_CLASS_AUDIO,
+ .bInterfaceSubClass = USB_SUBCLASS_AUDIOCONTROL,
.driver_info = (unsigned long) & (const struct snd_usb_audio_quirk) {
.vendor_name = "Logitech, Inc.",
.product_name = "QuickCam Pro 9000",
USB_DEVICE_VENDOR_SPEC(0x0582, 0x0108),
.driver_info = (unsigned long) & (const struct snd_usb_audio_quirk) {
.ifnum = 0,
- .type = QUIRK_MIDI_STANDARD_INTERFACE
+ .type = QUIRK_MIDI_FIXED_ENDPOINT,
+ .data = & (const struct snd_usb_midi_endpoint_info) {
+ .out_cables = 0x0007,
+ .in_cables = 0x0007
+ }
}
},
{
def get_kallsyms_table():
global kallsyms
+
try:
f = open("/proc/kallsyms", "r")
- linecount = 0
- for line in f:
- linecount = linecount+1
- f.seek(0)
except:
return
-
- j = 0
for line in f:
loc = int(line.split()[0], 16)
name = line.split()[2]
- j = j +1
- if ((j % 100) == 0):
- print "\r" + str(j) + "/" + str(linecount),
- kallsyms.append({ 'loc': loc, 'name' : name})
-
- print "\r" + str(j) + "/" + str(linecount)
+ kallsyms.append((loc, name))
kallsyms.sort()
- return
def get_sym(sloc):
loc = int(sloc)
- for i in kallsyms:
- if (i['loc'] >= loc):
- return (i['name'], i['loc']-loc)
- return (None, 0)
+
+ # Invariant: kallsyms[i][0] <= loc for all 0 <= i <= start
+ # kallsyms[i][0] > loc for all end <= i < len(kallsyms)
+ start, end = -1, len(kallsyms)
+ while end != start + 1:
+ pivot = (start + end) // 2
+ if loc < kallsyms[pivot][0]:
+ end = pivot
+ else:
+ start = pivot
+
+ # Now (start == -1 or kallsyms[start][0] <= loc)
+ # and (start == len(kallsyms) - 1 or loc < kallsyms[start + 1][0])
+ if start >= 0:
+ symloc, name = kallsyms[start]
+ return (name, loc - symloc)
+ else:
+ return (None, 0)
def print_drop_table():
print "%25s %25s %25s" % ("LOCATION", "OFFSET", "COUNT")
# called from perf, when it finds a correspoinding event
def skb__kfree_skb(name, context, cpu, sec, nsec, pid, comm,
- skbaddr, protocol, location):
+ skbaddr, location, protocol):
slocation = str(location)
try:
drop_log[slocation] = drop_log[slocation] + 1
TARGETS += mqueue
TARGETS += net
TARGETS += ptrace
-TARGETS += soft-dirty
TARGETS += vm
all:
+++ /dev/null
-CFLAGS += -iquote../../../../include/uapi -Wall
-soft-dirty: soft-dirty.c
-
-all: soft-dirty
-
-clean:
- rm -f soft-dirty
-
-run_tests: all
- @./soft-dirty || echo "soft-dirty selftests: [FAIL]"
+++ /dev/null
-#include <stdlib.h>
-#include <stdio.h>
-#include <sys/mman.h>
-#include <unistd.h>
-#include <fcntl.h>
-#include <sys/types.h>
-
-typedef unsigned long long u64;
-
-#define PME_PRESENT (1ULL << 63)
-#define PME_SOFT_DIRTY (1Ull << 55)
-
-#define PAGES_TO_TEST 3
-#ifndef PAGE_SIZE
-#define PAGE_SIZE 4096
-#endif
-
-static void get_pagemap2(char *mem, u64 *map)
-{
- int fd;
-
- fd = open("/proc/self/pagemap2", O_RDONLY);
- if (fd < 0) {
- perror("Can't open pagemap2");
- exit(1);
- }
-
- lseek(fd, (unsigned long)mem / PAGE_SIZE * sizeof(u64), SEEK_SET);
- read(fd, map, sizeof(u64) * PAGES_TO_TEST);
- close(fd);
-}
-
-static inline char map_p(u64 map)
-{
- return map & PME_PRESENT ? 'p' : '-';
-}
-
-static inline char map_sd(u64 map)
-{
- return map & PME_SOFT_DIRTY ? 'd' : '-';
-}
-
-static int check_pte(int step, int page, u64 *map, u64 want)
-{
- if ((map[page] & want) != want) {
- printf("Step %d Page %d has %c%c, want %c%c\n",
- step, page,
- map_p(map[page]), map_sd(map[page]),
- map_p(want), map_sd(want));
- return 1;
- }
-
- return 0;
-}
-
-static void clear_refs(void)
-{
- int fd;
- char *v = "4";
-
- fd = open("/proc/self/clear_refs", O_WRONLY);
- if (write(fd, v, 3) < 3) {
- perror("Can't clear soft-dirty bit");
- exit(1);
- }
- close(fd);
-}
-
-int main(void)
-{
- char *mem, x;
- u64 map[PAGES_TO_TEST];
-
- mem = mmap(NULL, PAGES_TO_TEST * PAGE_SIZE,
- PROT_READ | PROT_WRITE, MAP_PRIVATE | MAP_ANON, 0, 0);
-
- x = mem[0];
- mem[2 * PAGE_SIZE] = 'c';
- get_pagemap2(mem, map);
-
- if (check_pte(1, 0, map, PME_PRESENT))
- return 1;
- if (check_pte(1, 1, map, 0))
- return 1;
- if (check_pte(1, 2, map, PME_PRESENT | PME_SOFT_DIRTY))
- return 1;
-
- clear_refs();
- get_pagemap2(mem, map);
-
- if (check_pte(2, 0, map, PME_PRESENT))
- return 1;
- if (check_pte(2, 1, map, 0))
- return 1;
- if (check_pte(2, 2, map, PME_PRESENT))
- return 1;
-
- mem[0] = 'a';
- mem[PAGE_SIZE] = 'b';
- x = mem[2 * PAGE_SIZE];
- get_pagemap2(mem, map);
-
- if (check_pte(3, 0, map, PME_PRESENT | PME_SOFT_DIRTY))
- return 1;
- if (check_pte(3, 1, map, PME_PRESENT | PME_SOFT_DIRTY))
- return 1;
- if (check_pte(3, 2, map, PME_PRESENT))
- return 1;
-
- (void)x; /* gcc warn */
-
- printf("PASS\n");
- return 0;
-}
projects / ~andy / linux / commitdiff