ARM: Kirkwood: fix ns2 gpios by converting to pinctrl

Note that the pinctrl conversion also fixes GPIO support for ns2 boards.
Since commit f9e75922: "ARM: Kirkwood: Make use of mvebu pincltl and
gpio", the mvbu_gpio driver is used for DT boards. As mvbu_gpio relies
on the pinctrl driver, then a pinctrl definition must be given to allow
the GPIO configuration.

Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

diff --git a/arch/arm/boot/dts/kirkwood-ns2-common.dtsi b/arch/arm/boot/dts/kirkwood-ns2-common.dtsi
index 9bc6785ad228f9522c73ad0df60befa33ef798a4..77d21abfcdf73a3430f529be076cb4f17cd9e13d 100644 (file)
--- a/arch/arm/boot/dts/kirkwood-ns2-common.dtsi
+++ b/arch/arm/boot/dts/kirkwood-ns2-common.dtsi
@@ -1,4 +1,5 @@
 /include/ "kirkwood.dtsi"
+/include/ "kirkwood-6281.dtsi"
 
 / {
        chosen {
@@ -6,6 +7,21 @@
        };
 
        ocp@f1000000 {
+               pinctrl: pinctrl@10000 {
+                       pinctrl-0 = < &pmx_spi &pmx_twsi0 &pmx_uart0
+                                       &pmx_ns2_sata0 &pmx_ns2_sata1>;
+                       pinctrl-names = "default";
+
+                       pmx_ns2_sata0: pmx-ns2-sata0 {
+                               marvell,pins = "mpp21";
+                               marvell,function = "sata0";
+                       };
+                       pmx_ns2_sata1: pmx-ns2-sata1 {
+                               marvell,pins = "mpp20";
+                               marvell,function = "sata1";
+                       };
+               };
+
                serial@12000 {
                        clock-frequency = <166666667>;
                        status = "okay";

diff --git a/arch/arm/mach-kirkwood/board-ns2.c b/arch/arm/mach-kirkwood/board-ns2.c
index 8821720ab5a481ca048b0acb1ef01010055ffa7f..f4632a809f6895a0481ea1876e3e0fe25da36fe8 100644 (file)
--- a/arch/arm/mach-kirkwood/board-ns2.c
+++ b/arch/arm/mach-kirkwood/board-ns2.c
@@ -18,47 +18,11 @@
 #include <linux/gpio.h>
 #include <linux/of.h>
 #include "common.h"
-#include "mpp.h"
 
 static struct mv643xx_eth_platform_data ns2_ge00_data = {
        .phy_addr       = MV643XX_ETH_PHY_ADDR(8),
 };
 
-static unsigned int ns2_mpp_config[] __initdata = {
-       MPP0_SPI_SCn,
-       MPP1_SPI_MOSI,
-       MPP2_SPI_SCK,
-       MPP3_SPI_MISO,
-       MPP4_NF_IO6,
-       MPP5_NF_IO7,
-       MPP6_SYSRST_OUTn,
-       MPP7_GPO,               /* Fan speed (bit 1) */
-       MPP8_TW0_SDA,
-       MPP9_TW0_SCK,
-       MPP10_UART0_TXD,
-       MPP11_UART0_RXD,
-       MPP12_GPO,              /* Red led */
-       MPP14_GPIO,             /* USB fuse */
-       MPP16_GPIO,             /* SATA 0 power */
-       MPP17_GPIO,             /* SATA 1 power */
-       MPP18_NF_IO0,
-       MPP19_NF_IO1,
-       MPP20_SATA1_ACTn,
-       MPP21_SATA0_ACTn,
-       MPP22_GPIO,             /* Fan speed (bit 0) */
-       MPP23_GPIO,             /* Fan power */
-       MPP24_GPIO,             /* USB mode select */
-       MPP25_GPIO,             /* Fan rotation fail */
-       MPP26_GPIO,             /* USB device vbus */
-       MPP28_GPIO,             /* USB enable host vbus */
-       MPP29_GPIO,             /* Blue led (slow register) */
-       MPP30_GPIO,             /* Blue led (command register) */
-       MPP31_GPIO,             /* Board power off */
-       MPP32_GPIO,             /* Power button (0 = Released, 1 = Pushed) */
-       MPP33_GPO,              /* Fan speed (bit 2) */
-       0
-};
-
 #define NS2_GPIO_POWER_OFF     31
 
 static void ns2_power_off(void)
@@ -71,8 +35,6 @@ void __init ns2_init(void)
        /*
         * Basic setup. Needs to be called early.
         */
-       kirkwood_mpp_conf(ns2_mpp_config);
-
        if (of_machine_is_compatible("lacie,netspace_lite_v2") ||
            of_machine_is_compatible("lacie,netspace_mini_v2"))
                ns2_ge00_data.phy_addr = MV643XX_ETH_PHY_ADDR(0);