Fix some spelling errors and inconsistencies in comment blocks.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* For non-82573 silicon, write data to EEPROM at offset using SPI interface.
*
* If e1000e_update_nvm_checksum is not called after this function, the
- * EEPROM will most likley contain an invalid checksum.
+ * EEPROM will most likely contain an invalid checksum.
**/
static s32 e1000_write_nvm_82571(struct e1000_hw *hw, u16 offset, u16 words,
u16 *data)
* poll for completion.
*
* If e1000e_update_nvm_checksum is not called after this function, the
- * EEPROM will most likley contain an invalid checksum.
+ * EEPROM will most likely contain an invalid checksum.
**/
static s32 e1000_write_nvm_eewr_82571(struct e1000_hw *hw, u16 offset,
u16 words, u16 *data)
/* If SerDes loopback mode is entered, there is no form
* of reset to take the adapter out of that mode. So we
* have to explicitly take the adapter out of loopback
- * mode. This prevents drivers from twidling their thumbs
+ * mode. This prevents drivers from twiddling their thumbs
* if another tool failed to take it out of loopback mode.
*/
ew32(SCTL,
* e1000e_get_laa_state_82571 - Get locally administered address state
* @hw: pointer to the HW structure
*
- * Retrieve and return the current locally administed address state.
+ * Retrieve and return the current locally administered address state.
**/
bool e1000e_get_laa_state_82571(struct e1000_hw *hw)
{
* @hw: pointer to the HW structure
* @state: enable/disable locally administered address
*
- * Enable/Disable the current locally administed address state.
+ * Enable/Disable the current locally administers address state.
**/
void e1000e_set_laa_state_82571(struct e1000_hw *hw, bool state)
{
#define E1000_WUFC_ARP 0x00000020 /* ARP Request Packet Wakeup Enable */
/* Extended Device Control */
-#define E1000_CTRL_EXT_SDP7_DATA 0x00000080 /* Value of SW Defineable Pin 7 */
+#define E1000_CTRL_EXT_SDP7_DATA 0x00000080 /* Value of SW Definable Pin 7 */
#define E1000_CTRL_EXT_EE_RST 0x00002000 /* Reinitialize from EEPROM */
#define E1000_CTRL_EXT_RO_DIS 0x00020000 /* Relaxed Ordering disable */
#define E1000_CTRL_EXT_LINK_MODE_MASK 0x00C00000
#define E1000_CTRL_EXT_IAME 0x08000000 /* Interrupt acknowledge Auto-mask */
#define E1000_CTRL_EXT_INT_TIMER_CLR 0x20000000 /* Clear Interrupt timers after IMS clear */
-/* Receive Decriptor bit definitions */
+/* Receive Descriptor bit definitions */
#define E1000_RXD_STAT_DD 0x01 /* Descriptor Done */
#define E1000_RXD_STAT_EOP 0x02 /* End of Packet */
#define E1000_RXD_STAT_IXSM 0x04 /* Ignore checksum */
#define E1000_RXD_STAT_VP 0x08 /* IEEE VLAN Packet */
-#define E1000_RXD_STAT_UDPCS 0x10 /* UDP xsum caculated */
+#define E1000_RXD_STAT_UDPCS 0x10 /* UDP xsum calculated */
#define E1000_RXD_STAT_TCPCS 0x20 /* TCP xsum calculated */
#define E1000_RXD_ERR_CE 0x01 /* CRC Error */
#define E1000_RXD_ERR_SE 0x02 /* Symbol Error */
#define E1000_STATUS_LAN_INIT_DONE 0x00000200 /* Lan Init Completion by NVM */
#define E1000_STATUS_GIO_MASTER_ENABLE 0x00080000 /* Status of Master requests. */
-/* Constants used to intrepret the masked PCI-X bus speed. */
+/* Constants used to interpret the masked PCI-X bus speed. */
#define HALF_DUPLEX 1
#define FULL_DUPLEX 2
/* PHY 1000 MII Register/Bit Definitions */
/* PHY Registers defined by IEEE */
#define PHY_CONTROL 0x00 /* Control Register */
-#define PHY_STATUS 0x01 /* Status Regiser */
+#define PHY_STATUS 0x01 /* Status Register */
#define PHY_ID1 0x02 /* Phy Id Reg (word 1) */
#define PHY_ID2 0x03 /* Phy Id Reg (word 2) */
#define PHY_AUTONEG_ADV 0x04 /* Autoneg Advertisement */
E1000_ICRXDMTC = 0x04120, /* Irq Cause Rx Desc MinThreshold Count */
E1000_ICRXOC = 0x04124, /* Irq Cause Receiver Overrun Count */
E1000_RXCSUM = 0x05000, /* RX Checksum Control - RW */
- E1000_RFCTL = 0x05008, /* Receive Filter Control*/
+ E1000_RFCTL = 0x05008, /* Receive Filter Control */
E1000_MTA = 0x05200, /* Multicast Table Array - RW Array */
E1000_RA = 0x05400, /* Receive Address - RW Array */
E1000_VFTA = 0x05600, /* VLAN Filter Table Array - RW Array */
E1000_FACTPS = 0x05B30, /* Function Active and Power State to MNG */
E1000_SWSM = 0x05B50, /* SW Semaphore */
E1000_FWSM = 0x05B54, /* FW Semaphore */
- E1000_HICR = 0x08F00, /* Host Inteface Control */
+ E1000_HICR = 0x08F00, /* Host Interface Control */
};
/* RSS registers */
* e1000_check_polarity_ife_ich8lan - Check cable polarity for IFE PHY
* @hw: pointer to the HW structure
*
- * Polarity is determined on the polarity reveral feature being enabled.
+ * Polarity is determined on the polarity reversal feature being enabled.
* This function is only called by other family-specific
* routines.
**/
/* Either we should have a hardware SPI cycle in progress
* bit to check against, in order to start a new cycle or
* FDONE bit should be changed in the hardware so that it
- * is 1 after harware reset, which can then be used as an
+ * is 1 after hardware reset, which can then be used as an
* indication whether a cycle is in progress or has been
* completed.
*/
* which writes the checksum to the shadow ram. The changes in the shadow
* ram are then committed to the EEPROM by processing each bank at a time
* checking for the modified bit and writing only the pending changes.
- * After a succesful commit, the shadow ram is cleared and is ready for
+ * After a successful commit, the shadow ram is cleared and is ready for
* future writes.
**/
static s32 e1000_update_nvm_checksum_ich8lan(struct e1000_hw *hw)
* - initialize LED identification
* - setup receive address registers
* - setup flow control
- * - setup transmit discriptors
+ * - setup transmit descriptors
* - clear statistics
**/
static s32 e1000_init_hw_ich8lan(struct e1000_hw *hw)
E1000_PHY_CTRL_NOND0A_GBE_DISABLE);
ew32(PHY_CTRL, phy_ctrl);
- /* Call gig speed drop workaround on Giga disable before accessing
+ /* Call gig speed drop workaround on Gig disable before accessing
* any PHY registers */
e1000e_gig_downshift_workaround_ich8lan(hw);
/**
* e1000_set_kmrn_lock_loss_workaound_ich8lan - Set Kumeran workaround state
* @hw: pointer to the HW structure
- * @state: boolean value used to set the current Kumaran workaround state
+ * @state: boolean value used to set the current Kumeran workaround state
*
* If ICH8, set the current Kumeran workaround state (enabled - TRUE
* /disabled - FALSE).
E1000_PHY_CTRL_NOND0A_GBE_DISABLE);
ew32(PHY_CTRL, reg);
- /* Call gig speed drop workaround on Giga disable before
+ /* Call gig speed drop workaround on Gig disable before
* accessing any PHY registers */
if (hw->mac.type == e1000_ich8lan)
e1000e_gig_downshift_workaround_ich8lan(hw);
* @hw: pointer to the HW structure
*
* Steps to take when dropping from 1Gb/s (eg. link cable removal (LSC),
- * LPLU, Giga disable, MDIC PHY reset):
+ * LPLU, Gig disable, MDIC PHY reset):
* 1) Set Kumeran Near-end loopback
* 2) Clear Kumeran Near-end loopback
* Should only be called for ICH8[m] devices with IGP_3 Phy.
}
/**
- * e1000_led_on_ich8lan - Turn LED's on
+ * e1000_led_on_ich8lan - Turn LEDs on
* @hw: pointer to the HW structure
*
- * Turn on the LED's.
+ * Turn on the LEDs.
**/
static s32 e1000_led_on_ich8lan(struct e1000_hw *hw)
{
}
/**
- * e1000_led_off_ich8lan - Turn LED's off
+ * e1000_led_off_ich8lan - Turn LEDs off
* @hw: pointer to the HW structure
*
- * Turn off the LED's.
+ * Turn off the LEDs.
**/
static s32 e1000_led_off_ich8lan(struct e1000_hw *hw)
{
}
/**
- * e1000e_get_speed_and_duplex_copper - Retreive current speed/duplex
+ * e1000e_get_speed_and_duplex_copper - Retrieve current speed/duplex
* @hw: pointer to the HW structure
* @speed: stores the current speed
* @duplex: stores the current duplex
}
/**
- * e1000e_get_speed_and_duplex_fiber_serdes - Retreive current speed/duplex
+ * e1000e_get_speed_and_duplex_fiber_serdes - Retrieve current speed/duplex
* @hw: pointer to the HW structure
* @speed: stores the current speed
* @duplex: stores the current duplex
* e1000e_blink_led - Blink LED
* @hw: pointer to the HW structure
*
- * Blink the led's which are set to be on.
+ * Blink the LEDs which are set to be on.
**/
s32 e1000e_blink_led(struct e1000_hw *hw)
{
* @hw: pointer to the HW structure
*
* Returns 0 if successful, else returns -10
- * (-E1000_ERR_MASTER_REQUESTS_PENDING) if master disable bit has not casued
+ * (-E1000_ERR_MASTER_REQUESTS_PENDING) if master disable bit has not caused
* the master requests to be disabled.
*
* Disables PCI-Express master access and verifies there are no pending
}
/**
- * e1000e_read_nvm_spi - Read EEPROM's using SPI
+ * e1000e_read_nvm_spi - Reads EEPROM using SPI
* @hw: pointer to the HW structure
* @offset: offset of word in the EEPROM to read
* @words: number of words to read
* Writes data to EEPROM at offset using SPI interface.
*
* If e1000e_update_nvm_checksum is not called after this function , the
- * EEPROM will most likley contain an invalid checksum.
+ * EEPROM will most likely contain an invalid checksum.
**/
s32 e1000e_write_nvm_spi(struct e1000_hw *hw, u16 offset, u16 words, u16 *data)
{
*
* Returns E1000_success upon success, else E1000_ERR_HOST_INTERFACE_COMMAND
*
- * This function checks whether the HOST IF is enabled for command operaton
+ * This function checks whether the HOST IF is enabled for command operation
* and also checks whether the previous command is completed. It busy waits
* in case of previous command is not completed.
**/
}
/**
- * e1000e_check_mng_mode - check managament mode
+ * e1000e_check_mng_mode - check management mode
* @hw: pointer to the HW structure
*
* Reads the firmware semaphore register and returns true (>0) if
* e1000_get_hw_control - get control of the h/w from f/w
* @adapter: address of board private structure
*
- * e1000_get_hw_control sets {CTRL_EXT|FWSM}:DRV_LOAD bit.
+ * e1000_get_hw_control sets {CTRL_EXT|SWSM}:DRV_LOAD bit.
* For ASF and Pass Through versions of f/w this means that
* the driver is loaded. For AMT version (only with 82573)
* of the f/w this means that the network i/f is open.
* e1000_release_hw_control - release control of the h/w to f/w
* @adapter: address of board private structure
*
- * e1000_release_hw_control resets {CTRL_EXT|FWSM}:DRV_LOAD bit.
+ * e1000_release_hw_control resets {CTRL_EXT|SWSM}:DRV_LOAD bit.
* For ASF and Pass Through versions of f/w this means that the
* driver is no longer loaded. For AMT version (only with 82573) i
* of the f/w this means that the network i/f is closed.
/**
* e1000_update_itr - update the dynamic ITR value based on statistics
+ * @adapter: pointer to adapter
+ * @itr_setting: current adapter->itr
+ * @packets: the number of packets during this measurement interval
+ * @bytes: the number of bytes during this measurement interval
+ *
* Stores a new ITR value based on packets and byte
* counts during the last interrupt. The advantage of per interrupt
* computation is faster updates and more accurate ITR for the current
* while increasing bulk throughput.
* this functionality is controlled by the InterruptThrottleRate module
* parameter (see e1000_param.c)
- * @adapter: pointer to adapter
- * @itr_setting: current adapter->itr
- * @packets: the number of packets during this measurement interval
- * @bytes: the number of bytes during this measurement interval
**/
static unsigned int e1000_update_itr(struct e1000_adapter *adapter,
u16 itr_setting, int packets,
/**
* e1000_clean - NAPI Rx polling callback
* @adapter: board private structure
+ * @budget: amount of packets driver is allowed to process this poll
**/
static int e1000_clean(struct napi_struct *napi, int budget)
{
e1000_check_reset_block(hw))
return;
- /* managebility (AMT) is enabled */
+ /* manageability (AMT) is enabled */
if (er32(MANC) & E1000_MANC_SMBUS_EN)
return;
* @offset: register offset to be read
* @data: pointer to the read data
*
- * Reads the MDI control regsiter in the PHY at offset and stores the
+ * Reads the MDI control register in the PHY at offset and stores the
* information read to data.
**/
static s32 e1000_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data)
}
/**
- * e1000e_check_downshift - Checks whether a downshift in speed occured
+ * e1000e_check_downshift - Checks whether a downshift in speed occurred
* @hw: pointer to the HW structure
*
* Success returns 0, Failure returns 1
*
* The automatic gain control (agc) normalizes the amplitude of the
* received signal, adjusting for the attenuation produced by the
- * cable. By reading the AGC registers, which reperesent the
- * cobination of course and fine gain value, the value can be put
+ * cable. By reading the AGC registers, which represent the
+ * combination of course and fine gain value, the value can be put
* into a lookup table to obtain the approximate cable length
* for each channel.
**/
* Verify the reset block is not blocking us from resetting. Acquire
* semaphore (if necessary) and read/set/write the device control reset
* bit in the PHY. Wait the appropriate delay time for the device to
- * reset and relase the semaphore (if necessary).
+ * reset and release the semaphore (if necessary).
**/
s32 e1000e_phy_hw_reset_generic(struct e1000_hw *hw)
{
projects / ~andy / linux / commitdiff