--- /dev/null
+/*
+ * at91-qil_a9260.dts - Device Tree file for Calao QIL A9260 board
+ *
+ * Copyright (C) 2011-2013 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ *
+ * Licensed under GPLv2.
+ */
+/dts-v1/;
+#include "at91sam9260.dtsi"
+/ {
+ model = "Calao QIL A9260";
+ compatible = "calao,qil-a9260", "atmel,at91sam9260", "atmel,at91sam9";
+
+ chosen {
+ bootargs = "console=ttyS0,115200";
+ };
+
+ memory {
+ reg = <0x20000000 0x4000000>;
+ };
+
+ clocks {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ main_clock: clock@0 {
+ compatible = "atmel,osc", "fixed-clock";
+ clock-frequency = <12000000>;
+ };
+ };
+
+ ahb {
+ apb {
+ usb1: gadget@fffa4000 {
+ atmel,vbus-gpio = <&pioC 5 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+ };
+
+ mmc0: mmc@fffa8000 {
+ pinctrl-0 = <
+ &pinctrl_mmc0_clk
+ &pinctrl_mmc0_slot0_cmd_dat0
+ &pinctrl_mmc0_slot0_dat1_3>;
+ status = "okay";
+ slot@0 {
+ reg = <0>;
+ bus-width = <4>;
+ };
+ };
+
+ usart0: serial@fffb0000 {
+ pinctrl-0 =
+ <&pinctrl_usart0
+ &pinctrl_usart0_rts
+ &pinctrl_usart0_cts
+ &pinctrl_usart0_dtr_dsr
+ &pinctrl_usart0_dcd
+ &pinctrl_usart0_ri>;
+ status = "okay";
+ };
+
+ usart1: serial@fffb4000 {
+ pinctrl-0 =
+ <&pinctrl_usart1
+ &pinctrl_usart1_rts
+ &pinctrl_usart1_cts>;
+ status = "okay";
+ };
+
+ usart2: serial@fffb8000 {
+ pinctrl-0 =
+ <&pinctrl_usart2
+ &pinctrl_usart2_rts
+ &pinctrl_usart2_cts>;
+ status = "okay";
+ };
+
+ macb0: ethernet@fffc4000 {
+ phy-mode = "rmii";
+ status = "okay";
+ };
+
+ spi0: spi@fffc8000 {
+ status = "okay";
+ cs-gpios = <&pioA 3 GPIO_ACTIVE_HIGH>;
+
+ m41t94@0 {
+ compatible = "st,m41t94";
+ reg = <0>;
+ spi-max-frequency = <1000000>;
+ };
+
+ };
+
+ dbgu: serial@fffff200 {
+ status = "okay";
+ };
+
+ shdwc@fffffd10 {
+ atmel,wakeup-counter = <10>;
+ atmel,wakeup-rtt-timer;
+ };
+ };
+
+ usb0: ohci@00500000 {
+ num-ports = <2>;
+ status = "okay";
+ };
+
+ nand0: nand@40000000 {
+ nand-bus-width = <8>;
+ nand-ecc-mode = "soft";
+ nand-on-flash-bbt;
+ status = "okay";
+
+ at91bootstrap@0 {
+ label = "at91bootstrap";
+ reg = <0x0 0x20000>;
+ };
+
+ barebox@20000 {
+ label = "barebox";
+ reg = <0x20000 0x40000>;
+ };
+
+ bareboxenv@60000 {
+ label = "bareboxenv";
+ reg = <0x60000 0x20000>;
+ };
+
+ bareboxenv2@80000 {
+ label = "bareboxenv2";
+ reg = <0x80000 0x20000>;
+ };
+
+ oftree@a0000 {
+ label = "oftree";
+ reg = <0xa0000 0x20000>;
+ };
+
+ kernel@c0000 {
+ label = "kernel";
+ reg = <0xc0000 0x400000>;
+ };
+
+ rootfs@4c0000 {
+ label = "rootfs";
+ reg = <0x4c0000 0x7800000>;
+ };
+
+ data@7cc0000 {
+ label = "data";
+ reg = <0x7cc0000 0x8340000>;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ user_led {
+ label = "user_led";
+ gpios = <&pioB 21 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ user_pb {
+ label = "user_pb";
+ gpios = <&pioB 10 GPIO_ACTIVE_LOW>;
+ linux,code = <28>;
+ gpio-key,wakeup;
+ };
+ };
+
+ i2c@0 {
+ status = "okay";
+ };
+};
+++ /dev/null
-/*
- * linux/arch/arm/mach-at91/board-qil-a9260.c
- *
- * Copyright (C) 2005 SAN People
- * Copyright (C) 2006 Atmel
- * Copyright (C) 2007 Calao-systems
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- */
-
-#include <linux/types.h>
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/spi/spi.h>
-#include <linux/gpio_keys.h>
-#include <linux/input.h>
-#include <linux/clk.h>
-
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-#include <mach/hardware.h>
-#include <mach/at91sam9_smc.h>
-
-#include "at91_aic.h"
-#include "at91_shdwc.h"
-#include "board.h"
-#include "sam9_smc.h"
-#include "generic.h"
-
-
-static void __init ek_init_early(void)
-{
- /* Initialize processor: 12.000 MHz crystal */
- at91_initialize(12000000);
-}
-
-/*
- * USB Host port
- */
-static struct at91_usbh_data __initdata ek_usbh_data = {
- .ports = 2,
- .vbus_pin = {-EINVAL, -EINVAL},
- .overcurrent_pin= {-EINVAL, -EINVAL},
-};
-
-/*
- * USB Device port
- */
-static struct at91_udc_data __initdata ek_udc_data = {
- .vbus_pin = AT91_PIN_PC5,
- .pullup_pin = -EINVAL, /* pull-up driven by UDC */
-};
-
-/*
- * SPI devices.
- */
-static struct spi_board_info ek_spi_devices[] = {
-#if defined(CONFIG_RTC_DRV_M41T94)
- { /* M41T94 RTC */
- .modalias = "m41t94",
- .chip_select = 0,
- .max_speed_hz = 1 * 1000 * 1000,
- .bus_num = 0,
- }
-#endif
-};
-
-/*
- * MACB Ethernet device
- */
-static struct macb_platform_data __initdata ek_macb_data = {
- .phy_irq_pin = AT91_PIN_PA31,
- .is_rmii = 1,
-};
-
-/*
- * NAND flash
- */
-static struct mtd_partition __initdata ek_nand_partition[] = {
- {
- .name = "Uboot & Kernel",
- .offset = 0,
- .size = SZ_16M,
- },
- {
- .name = "Root FS",
- .offset = MTDPART_OFS_NXTBLK,
- .size = 120 * SZ_1M,
- },
- {
- .name = "FS",
- .offset = MTDPART_OFS_NXTBLK,
- .size = 120 * SZ_1M,
- },
-};
-
-static struct atmel_nand_data __initdata ek_nand_data = {
- .ale = 21,
- .cle = 22,
- .det_pin = -EINVAL,
- .rdy_pin = AT91_PIN_PC13,
- .enable_pin = AT91_PIN_PC14,
- .ecc_mode = NAND_ECC_SOFT,
- .on_flash_bbt = 1,
- .parts = ek_nand_partition,
- .num_parts = ARRAY_SIZE(ek_nand_partition),
-};
-
-static struct sam9_smc_config __initdata ek_nand_smc_config = {
- .ncs_read_setup = 0,
- .nrd_setup = 1,
- .ncs_write_setup = 0,
- .nwe_setup = 1,
-
- .ncs_read_pulse = 3,
- .nrd_pulse = 3,
- .ncs_write_pulse = 3,
- .nwe_pulse = 3,
-
- .read_cycle = 5,
- .write_cycle = 5,
-
- .mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8,
- .tdf_cycles = 2,
-};
-
-static void __init ek_add_device_nand(void)
-{
- /* configure chip-select 3 (NAND) */
- sam9_smc_configure(0, 3, &ek_nand_smc_config);
-
- at91_add_device_nand(&ek_nand_data);
-}
-
-/*
- * MCI (SD/MMC)
- */
-static struct mci_platform_data __initdata ek_mci0_data = {
- .slot[0] = {
- .bus_width = 4,
- .detect_pin = -EINVAL,
- .wp_pin = -EINVAL,
- },
-};
-
-/*
- * GPIO Buttons
- */
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
-static struct gpio_keys_button ek_buttons[] = {
- { /* USER PUSH BUTTON */
- .code = KEY_ENTER,
- .gpio = AT91_PIN_PB10,
- .active_low = 1,
- .desc = "user_pb",
- .wakeup = 1,
- }
-};
-
-static struct gpio_keys_platform_data ek_button_data = {
- .buttons = ek_buttons,
- .nbuttons = ARRAY_SIZE(ek_buttons),
-};
-
-static struct platform_device ek_button_device = {
- .name = "gpio-keys",
- .id = -1,
- .num_resources = 0,
- .dev = {
- .platform_data = &ek_button_data,
- }
-};
-
-static void __init ek_add_device_buttons(void)
-{
- at91_set_GPIO_periph(AT91_PIN_PB10, 1); /* user push button, pull up enabled */
- at91_set_deglitch(AT91_PIN_PB10, 1);
-
- platform_device_register(&ek_button_device);
-}
-#else
-static void __init ek_add_device_buttons(void) {}
-#endif
-
-/*
- * LEDs
- */
-static struct gpio_led ek_leds[] = {
- { /* user_led (green) */
- .name = "user_led",
- .gpio = AT91_PIN_PB21,
- .active_low = 0,
- .default_trigger = "heartbeat",
- }
-};
-
-static void __init ek_board_init(void)
-{
- /* Serial */
- /* DBGU on ttyS0. (Rx & Tx only) */
- at91_register_uart(0, 0, 0);
-
- /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
- at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
- | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
- | ATMEL_UART_RI);
-
- /* USART1 on ttyS2. (Rx, Tx, CTS, RTS) */
- at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
- /* USART2 on ttyS3. (Rx, Tx, CTS, RTS) */
- at91_register_uart(AT91SAM9260_ID_US2, 3, ATMEL_UART_CTS | ATMEL_UART_RTS);
- at91_add_device_serial();
- /* USB Host */
- at91_add_device_usbh(&ek_usbh_data);
- /* USB Device */
- at91_add_device_udc(&ek_udc_data);
- /* SPI */
- at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
- /* NAND */
- ek_add_device_nand();
- /* I2C */
- at91_add_device_i2c(NULL, 0);
- /* Ethernet */
- at91_add_device_eth(&ek_macb_data);
- /* MMC */
- at91_add_device_mci(0, &ek_mci0_data);
- /* Push Buttons */
- ek_add_device_buttons();
- /* LEDs */
- at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
- /* shutdown controller, wakeup button (5 msec low) */
- at91_shdwc_write(AT91_SHDW_MR, AT91_SHDW_CPTWK0_(10) | AT91_SHDW_WKMODE0_LOW
- | AT91_SHDW_RTTWKEN);
-}
-
-MACHINE_START(QIL_A9260, "CALAO QIL_A9260")
- /* Maintainer: calao-systems */
- .init_time = at91sam926x_pit_init,
- .map_io = at91_map_io,
- .handle_irq = at91_aic_handle_irq,
- .init_early = ek_init_early,
- .init_irq = at91_init_irq_default,
- .init_machine = ek_board_init,
-MACHINE_END
projects / ~andy / linux / commitdiff