X-Git-Url: http://pileus.org/git/?a=blobdiff_plain;f=arch%2Fh8300%2FKconfig;h=3d6759ee382f2721e29fd5a44f9c06e937fd7e3b;hb=8dce5f3dee21bf976193ddb06426b9727cf5d1a2;hp=303e4f9a79d19998452760a913828a64c5773345;hpb=aad760136537fdfa10e5ac76bd3c79bde2100863;p=~andy%2Flinux diff --git a/arch/h8300/Kconfig b/arch/h8300/Kconfig index 303e4f9a79d..3d6759ee382 100644 --- a/arch/h8300/Kconfig +++ b/arch/h8300/Kconfig @@ -94,126 +94,10 @@ endmenu source "net/Kconfig" -source "drivers/base/Kconfig" - -source "drivers/mtd/Kconfig" - -source "drivers/block/Kconfig" - -source "drivers/ide/Kconfig" +source "drivers/Kconfig" source "arch/h8300/Kconfig.ide" -source "drivers/net/Kconfig" - -# -# input - input/joystick depends on it. As does USB. -# -source "drivers/input/Kconfig" - -menu "Character devices" - -config VT - bool "Virtual terminal" - ---help--- - If you say Y here, you will get support for terminal devices with - display and keyboard devices. These are called "virtual" because you - can run several virtual terminals (also called virtual consoles) on - one physical terminal. This is rather useful, for example one - virtual terminal can collect system messages and warnings, another - one can be used for a text-mode user session, and a third could run - an X session, all in parallel. Switching between virtual terminals - is done with certain key combinations, usually Alt-. - - The setterm command ("man setterm") can be used to change the - properties (such as colors or beeping) of a virtual terminal. The - man page console_codes(4) ("man console_codes") contains the special - character sequences that can be used to change those properties - directly. The fonts used on virtual terminals can be changed with - the setfont ("man setfont") command and the key bindings are defined - with the loadkeys ("man loadkeys") command. - - You need at least one virtual terminal device in order to make use - of your keyboard and monitor. Therefore, only people configuring an - embedded system would want to say N here in order to save some - memory; the only way to log into such a system is then via a serial - or network connection. - - If unsure, say Y, or else you won't be able to do much with your new - shiny Linux system :-) - -config VT_CONSOLE - bool "Support for console on virtual terminal" - depends on VT - ---help--- - The system console is the device which receives all kernel messages - and warnings and which allows logins in single user mode. If you - answer Y here, a virtual terminal (the device used to interact with - a physical terminal) can be used as system console. This is the most - common mode of operations, so you should say Y here unless you want - the kernel messages be output only to a serial port (in which case - you should say Y to "Console on serial port", below). - - If you do say Y here, by default the currently visible virtual - terminal (/dev/tty0) will be used as system console. You can change - that with a kernel command line option such as "console=tty3" which - would use the third virtual terminal as system console. (Try "man - bootparam" or see the documentation of your boot loader (lilo or - loadlin) about how to pass options to the kernel at boot time.) - - If unsure, say Y. - -config HW_CONSOLE - bool - depends on VT - default y - -comment "Unix98 PTY support" - -config UNIX98_PTYS - bool "Unix98 PTY support" - ---help--- - A pseudo terminal (PTY) is a software device consisting of two - halves: a master and a slave. The slave device behaves identical to - a physical terminal; the master device is used by a process to - read data from and write data to the slave, thereby emulating a - terminal. Typical programs for the master side are telnet servers - and xterms. - - Linux has traditionally used the BSD-like names /dev/ptyxx for - masters and /dev/ttyxx for slaves of pseudo terminals. This scheme - has a number of problems. The GNU C library glibc 2.1 and later, - however, supports the Unix98 naming standard: in order to acquire a - pseudo terminal, a process opens /dev/ptmx; the number of the pseudo - terminal is then made available to the process and the pseudo - terminal slave can be accessed as /dev/pts/. What was - traditionally /dev/ttyp2 will then be /dev/pts/2, for example. - - The entries in /dev/pts/ are created on the fly by a virtual - file system; therefore, if you say Y here you should say Y to - "/dev/pts file system for Unix98 PTYs" as well. - - If you want to say Y here, you need to have the C library glibc 2.1 - or later (equal to libc-6.1, check with "ls -l /lib/libc.so.*"). - Read the instructions in pertaining to - pseudo terminals. It's safe to say N. - -source "drivers/char/pcmcia/Kconfig" - -source "drivers/tty/serial/Kconfig" - -source "drivers/i2c/Kconfig" - -source "drivers/hwmon/Kconfig" - -source "drivers/usb/Kconfig" - -source "drivers/uwb/Kconfig" - -endmenu - -source "drivers/staging/Kconfig" - source "fs/Kconfig" source "arch/h8300/Kconfig.debug"