* @assocresp_ies: extra information element(s) to add into (Re)Association
* Response frames or %NULL
* @assocresp_ies_len: length of assocresp_ies in octets
+ * @probe_resp_len: length of probe response template (@probe_resp)
+ * @probe_resp: probe response template (AP mode only)
*/
struct beacon_parameters {
u8 *head, *tail;
size_t proberesp_ies_len;
const u8 *assocresp_ies;
size_t assocresp_ies_len;
+ int probe_resp_len;
+ u8 *probe_resp;
};
/**
* doesn't verify much. Note, however, that the passed netdev may be
* %NULL as well if the user requested changing the channel for the
* device itself, or for a monitor interface.
+ * @get_channel: Get the current operating channel, should return %NULL if
+ * there's no single defined operating channel if for example the
+ * device implements channel hopping for multi-channel virtual interfaces.
*
* @scan: Request to do a scan. If returning zero, the scan request is given
* the driver, and will be valid until passed to cfg80211_scan_done().
*
* @tdls_mgmt: Transmit a TDLS management frame.
* @tdls_oper: Perform a high-level TDLS operation (e.g. TDLS link setup).
+ *
+ * @probe_client: probe an associated client, must return a cookie that it
+ * later passes to cfg80211_probe_status().
*/
struct cfg80211_ops {
int (*suspend)(struct wiphy *wiphy, struct cfg80211_wowlan *wow);
enum nl80211_channel_type channel_type,
bool channel_type_valid, unsigned int wait,
const u8 *buf, size_t len, bool no_cck,
- u64 *cookie);
+ bool dont_wait_for_ack, u64 *cookie);
int (*mgmt_tx_cancel_wait)(struct wiphy *wiphy,
struct net_device *dev,
u64 cookie);
u16 status_code, const u8 *buf, size_t len);
int (*tdls_oper)(struct wiphy *wiphy, struct net_device *dev,
u8 *peer, enum nl80211_tdls_operation oper);
+
+ int (*probe_client)(struct wiphy *wiphy, struct net_device *dev,
+ const u8 *peer, u64 *cookie);
+
+ struct ieee80211_channel *(*get_channel)(struct wiphy *wiphy);
};
/*
* teardown packets should be sent through the @NL80211_CMD_TDLS_MGMT
* command. When this flag is not set, @NL80211_CMD_TDLS_OPER should be
* used for asking the driver/firmware to perform a TDLS operation.
+ * @WIPHY_FLAG_HAVE_AP_SME: device integrates AP SME
+ * @WIPHY_FLAG_REPORTS_OBSS: the device will report beacons from other BSSes
+ * when there are virtual interfaces in AP mode by calling
+ * cfg80211_report_obss_beacon().
+ * @WIPHY_FLAG_AP_PROBE_RESP_OFFLOAD: When operating as an AP, the device
+ * responds to probe-requests in hardware.
*/
enum wiphy_flags {
WIPHY_FLAG_CUSTOM_REGULATORY = BIT(0),
WIPHY_FLAG_AP_UAPSD = BIT(14),
WIPHY_FLAG_SUPPORTS_TDLS = BIT(15),
WIPHY_FLAG_TDLS_EXTERNAL_SETUP = BIT(16),
+ WIPHY_FLAG_HAVE_AP_SME = BIT(17),
+ WIPHY_FLAG_REPORTS_OBSS = BIT(18),
+ WIPHY_FLAG_AP_PROBE_RESP_OFFLOAD = BIT(19),
};
/**
* @software_iftypes: bitmask of software interface types, these are not
* subject to any restrictions since they are purely managed in SW.
* @flags: wiphy flags, see &enum wiphy_flags
+ * @features: features advertised to nl80211, see &enum nl80211_feature_flags.
* @bss_priv_size: each BSS struct has private data allocated with it,
* this variable determines its size
* @max_scan_ssids: maximum number of SSIDs the device can scan for in
* may request, if implemented.
*
* @wowlan: WoWLAN support information
+ *
+ * @ap_sme_capa: AP SME capabilities, flags from &enum nl80211_ap_sme_features.
*/
struct wiphy {
/* assign these fields before you register the wiphy */
/* Supported interface modes, OR together BIT(NL80211_IFTYPE_...) */
u16 interface_modes;
- u32 flags;
+ u32 flags, features;
+
+ u32 ap_sme_capa;
enum cfg80211_signal_type signal_type;
u32 available_antennas_tx;
u32 available_antennas_rx;
+ /*
+ * Bitmap of supported protocols for probe response offloading
+ * see &enum nl80211_probe_resp_offload_support_attr. Only valid
+ * when the wiphy flag @WIPHY_FLAG_AP_PROBE_RESP_OFFLOAD is set.
+ */
+ u32 probe_resp_offload;
+
/* If multiple wiphys are registered and you're handed e.g.
* a regular netdev with assigned ieee80211_ptr, you won't
* know whether it points to a wiphy your driver has registered
int beacon_interval;
+ u32 ap_unexpected_nlpid;
+
#ifdef CONFIG_CFG80211_WEXT
/* wext data */
struct {
*
* This informs cfg80211 that BSS information was found and
* the BSS should be updated/added.
+ *
+ * NOTE: Returns a referenced struct, must be released with cfg80211_put_bss()!
*/
-struct cfg80211_bss*
+struct cfg80211_bss * __must_check
cfg80211_inform_bss_frame(struct wiphy *wiphy,
struct ieee80211_channel *channel,
struct ieee80211_mgmt *mgmt, size_t len,
*
* This informs cfg80211 that BSS information was found and
* the BSS should be updated/added.
+ *
+ * NOTE: Returns a referenced struct, must be released with cfg80211_put_bss()!
*/
-struct cfg80211_bss*
+struct cfg80211_bss * __must_check
cfg80211_inform_bss(struct wiphy *wiphy,
struct ieee80211_channel *channel,
const u8 *bssid,
void cfg80211_pmksa_candidate_notify(struct net_device *dev, int index,
const u8 *bssid, bool preauth, gfp_t gfp);
+/**
+ * cfg80211_rx_spurious_frame - inform userspace about a spurious frame
+ * @dev: The device the frame matched to
+ * @addr: the transmitter address
+ * @gfp: context flags
+ *
+ * This function is used in AP mode (only!) to inform userspace that
+ * a spurious class 3 frame was received, to be able to deauth the
+ * sender.
+ * Returns %true if the frame was passed to userspace (or this failed
+ * for a reason other than not having a subscription.)
+ */
+bool cfg80211_rx_spurious_frame(struct net_device *dev,
+ const u8 *addr, gfp_t gfp);
+
+/**
+ * cfg80211_rx_unexpected_4addr_frame - inform about unexpected WDS frame
+ * @dev: The device the frame matched to
+ * @addr: the transmitter address
+ * @gfp: context flags
+ *
+ * This function is used in AP mode (only!) to inform userspace that
+ * an associated station sent a 4addr frame but that wasn't expected.
+ * It is allowed and desirable to send this event only once for each
+ * station to avoid event flooding.
+ * Returns %true if the frame was passed to userspace (or this failed
+ * for a reason other than not having a subscription.)
+ */
+bool cfg80211_rx_unexpected_4addr_frame(struct net_device *dev,
+ const u8 *addr, gfp_t gfp);
+
+/**
+ * cfg80211_probe_status - notify userspace about probe status
+ * @dev: the device the probe was sent on
+ * @addr: the address of the peer
+ * @cookie: the cookie filled in @probe_client previously
+ * @acked: indicates whether probe was acked or not
+ * @gfp: allocation flags
+ */
+void cfg80211_probe_status(struct net_device *dev, const u8 *addr,
+ u64 cookie, bool acked, gfp_t gfp);
+
+/**
+ * cfg80211_report_obss_beacon - report beacon from other APs
+ * @wiphy: The wiphy that received the beacon
+ * @frame: the frame
+ * @len: length of the frame
+ * @freq: frequency the frame was received on
+ * @gfp: allocation flags
+ *
+ * Use this function to report to userspace when a beacon was
+ * received. It is not useful to call this when there is no
+ * netdev that is in AP/GO mode.
+ */
+void cfg80211_report_obss_beacon(struct wiphy *wiphy,
+ const u8 *frame, size_t len,
+ int freq, gfp_t gfp);
+
/* Logging, debugging and troubleshooting/diagnostic helpers. */
/* wiphy_printk helpers, similar to dev_printk */