u8 setting;
};
+/* Battery driver related data */
+/*
+ * ADC for the battery thermistor.
+ * When using the ABx500_ADC_THERM_BATCTRL the battery ID resistor is combined
+ * with a NTC resistor to both identify the battery and to measure its
+ * temperature. Different phone manufactures uses different techniques to both
+ * identify the battery and to read its temperature.
+ */
+enum abx500_adc_therm {
+ ABx500_ADC_THERM_BATCTRL,
+ ABx500_ADC_THERM_BATTEMP,
+};
+
+/**
+ * struct abx500_res_to_temp - defines one point in a temp to res curve. To
+ * be used in battery packs that combines the identification resistor with a
+ * NTC resistor.
+ * @temp: battery pack temperature in Celcius
+ * @resist: NTC resistor net total resistance
+ */
+struct abx500_res_to_temp {
+ int temp;
+ int resist;
+};
+
+/**
+ * struct abx500_v_to_cap - Table for translating voltage to capacity
+ * @voltage: Voltage in mV
+ * @capacity: Capacity in percent
+ */
+struct abx500_v_to_cap {
+ int voltage;
+ int capacity;
+};
+
+/* Forward declaration */
+struct abx500_fg;
+
+/**
+ * struct abx500_fg_parameters - Fuel gauge algorithm parameters, in seconds
+ * if not specified
+ * @recovery_sleep_timer: Time between measurements while recovering
+ * @recovery_total_time: Total recovery time
+ * @init_timer: Measurement interval during startup
+ * @init_discard_time: Time we discard voltage measurement at startup
+ * @init_total_time: Total init time during startup
+ * @high_curr_time: Time current has to be high to go to recovery
+ * @accu_charging: FG accumulation time while charging
+ * @accu_high_curr: FG accumulation time in high current mode
+ * @high_curr_threshold: High current threshold, in mA
+ * @lowbat_threshold: Low battery threshold, in mV
+ * @overbat_threshold: Over battery threshold, in mV
+ * @battok_falling_th_sel0 Threshold in mV for battOk signal sel0
+ * Resolution in 50 mV step.
+ * @battok_raising_th_sel1 Threshold in mV for battOk signal sel1
+ * Resolution in 50 mV step.
+ * @user_cap_limit Capacity reported from user must be within this
+ * limit to be considered as sane, in percentage
+ * points.
+ * @maint_thres This is the threshold where we stop reporting
+ * battery full while in maintenance, in per cent
+ */
+struct abx500_fg_parameters {
+ int recovery_sleep_timer;
+ int recovery_total_time;
+ int init_timer;
+ int init_discard_time;
+ int init_total_time;
+ int high_curr_time;
+ int accu_charging;
+ int accu_high_curr;
+ int high_curr_threshold;
+ int lowbat_threshold;
+ int overbat_threshold;
+ int battok_falling_th_sel0;
+ int battok_raising_th_sel1;
+ int user_cap_limit;
+ int maint_thres;
+};
+
+/**
+ * struct abx500_charger_maximization - struct used by the board config.
+ * @use_maxi: Enable maximization for this battery type
+ * @maxi_chg_curr: Maximum charger current allowed
+ * @maxi_wait_cycles: cycles to wait before setting charger current
+ * @charger_curr_step delta between two charger current settings (mA)
+ */
+struct abx500_maxim_parameters {
+ bool ena_maxi;
+ int chg_curr;
+ int wait_cycles;
+ int charger_curr_step;
+};
+
+/**
+ * struct abx500_battery_type - different batteries supported
+ * @name: battery technology
+ * @resis_high: battery upper resistance limit
+ * @resis_low: battery lower resistance limit
+ * @charge_full_design: Maximum battery capacity in mAh
+ * @nominal_voltage: Nominal voltage of the battery in mV
+ * @termination_vol: max voltage upto which battery can be charged
+ * @termination_curr battery charging termination current in mA
+ * @recharge_vol battery voltage limit that will trigger a new
+ * full charging cycle in the case where maintenan-
+ * -ce charging has been disabled
+ * @normal_cur_lvl: charger current in normal state in mA
+ * @normal_vol_lvl: charger voltage in normal state in mV
+ * @maint_a_cur_lvl: charger current in maintenance A state in mA
+ * @maint_a_vol_lvl: charger voltage in maintenance A state in mV
+ * @maint_a_chg_timer_h: charge time in maintenance A state
+ * @maint_b_cur_lvl: charger current in maintenance B state in mA
+ * @maint_b_vol_lvl: charger voltage in maintenance B state in mV
+ * @maint_b_chg_timer_h: charge time in maintenance B state
+ * @low_high_cur_lvl: charger current in temp low/high state in mA
+ * @low_high_vol_lvl: charger voltage in temp low/high state in mV'
+ * @battery_resistance: battery inner resistance in mOhm.
+ * @n_r_t_tbl_elements: number of elements in r_to_t_tbl
+ * @r_to_t_tbl: table containing resistance to temp points
+ * @n_v_cap_tbl_elements: number of elements in v_to_cap_tbl
+ * @v_to_cap_tbl: Voltage to capacity (in %) table
+ * @n_batres_tbl_elements number of elements in the batres_tbl
+ * @batres_tbl battery internal resistance vs temperature table
+ */
+struct abx500_battery_type {
+ int name;
+ int resis_high;
+ int resis_low;
+ int charge_full_design;
+ int nominal_voltage;
+ int termination_vol;
+ int termination_curr;
+ int recharge_vol;
+ int normal_cur_lvl;
+ int normal_vol_lvl;
+ int maint_a_cur_lvl;
+ int maint_a_vol_lvl;
+ int maint_a_chg_timer_h;
+ int maint_b_cur_lvl;
+ int maint_b_vol_lvl;
+ int maint_b_chg_timer_h;
+ int low_high_cur_lvl;
+ int low_high_vol_lvl;
+ int battery_resistance;
+ int n_temp_tbl_elements;
+ struct abx500_res_to_temp *r_to_t_tbl;
+ int n_v_cap_tbl_elements;
+ struct abx500_v_to_cap *v_to_cap_tbl;
+ int n_batres_tbl_elements;
+ struct batres_vs_temp *batres_tbl;
+};
+
+/**
+ * struct abx500_bm_capacity_levels - abx500 capacity level data
+ * @critical: critical capacity level in percent
+ * @low: low capacity level in percent
+ * @normal: normal capacity level in percent
+ * @high: high capacity level in percent
+ * @full: full capacity level in percent
+ */
+struct abx500_bm_capacity_levels {
+ int critical;
+ int low;
+ int normal;
+ int high;
+ int full;
+};
+
+/**
+ * struct abx500_bm_charger_parameters - Charger specific parameters
+ * @usb_volt_max: maximum allowed USB charger voltage in mV
+ * @usb_curr_max: maximum allowed USB charger current in mA
+ * @ac_volt_max: maximum allowed AC charger voltage in mV
+ * @ac_curr_max: maximum allowed AC charger current in mA
+ */
+struct abx500_bm_charger_parameters {
+ int usb_volt_max;
+ int usb_curr_max;
+ int ac_volt_max;
+ int ac_curr_max;
+};
+
+/**
+ * struct abx500_bm_data - abx500 battery management data
+ * @temp_under under this temp, charging is stopped
+ * @temp_low between this temp and temp_under charging is reduced
+ * @temp_high between this temp and temp_over charging is reduced
+ * @temp_over over this temp, charging is stopped
+ * @temp_now present battery temperature
+ * @temp_interval_chg temperature measurement interval in s when charging
+ * @temp_interval_nochg temperature measurement interval in s when not charging
+ * @main_safety_tmr_h safety timer for main charger
+ * @usb_safety_tmr_h safety timer for usb charger
+ * @bkup_bat_v voltage which we charge the backup battery with
+ * @bkup_bat_i current which we charge the backup battery with
+ * @no_maintenance indicates that maintenance charging is disabled
+ * @abx500_adc_therm placement of thermistor, batctrl or battemp adc
+ * @chg_unknown_bat flag to enable charging of unknown batteries
+ * @enable_overshoot flag to enable VBAT overshoot control
+ * @auto_trig flag to enable auto adc trigger
+ * @fg_res resistance of FG resistor in 0.1mOhm
+ * @n_btypes number of elements in array bat_type
+ * @batt_id index of the identified battery in array bat_type
+ * @interval_charging charge alg cycle period time when charging (sec)
+ * @interval_not_charging charge alg cycle period time when not charging (sec)
+ * @temp_hysteresis temperature hysteresis
+ * @gnd_lift_resistance Battery ground to phone ground resistance (mOhm)
+ * @maxi: maximization parameters
+ * @cap_levels capacity in percent for the different capacity levels
+ * @bat_type table of supported battery types
+ * @chg_params charger parameters
+ * @fg_params fuel gauge parameters
+ */
+struct abx500_bm_data {
+ int temp_under;
+ int temp_low;
+ int temp_high;
+ int temp_over;
+ int temp_now;
+ int temp_interval_chg;
+ int temp_interval_nochg;
+ int main_safety_tmr_h;
+ int usb_safety_tmr_h;
+ int bkup_bat_v;
+ int bkup_bat_i;
+ bool no_maintenance;
+ bool chg_unknown_bat;
+ bool enable_overshoot;
+ bool auto_trig;
+ enum abx500_adc_therm adc_therm;
+ int fg_res;
+ int n_btypes;
+ int batt_id;
+ int interval_charging;
+ int interval_not_charging;
+ int temp_hysteresis;
+ int gnd_lift_resistance;
+ const struct abx500_maxim_parameters *maxi;
+ const struct abx500_bm_capacity_levels *cap_levels;
+ const struct abx500_battery_type *bat_type;
+ const struct abx500_bm_charger_parameters *chg_params;
+ const struct abx500_fg_parameters *fg_params;
+};
+
+struct abx500_chargalg_platform_data {
+ char **supplied_to;
+ size_t num_supplicants;
+};
+
+struct abx500_charger_platform_data {
+ char **supplied_to;
+ size_t num_supplicants;
+ bool autopower_cfg;
+};
+
+struct abx500_btemp_platform_data {
+ char **supplied_to;
+ size_t num_supplicants;
+};
+
+struct abx500_fg_platform_data {
+ char **supplied_to;
+ size_t num_supplicants;
+};
+
+struct abx500_bm_plat_data {
+ struct abx500_bm_data *battery;
+ struct abx500_charger_platform_data *charger;
+ struct abx500_btemp_platform_data *btemp;
+ struct abx500_fg_platform_data *fg;
+ struct abx500_chargalg_platform_data *chargalg;
+};
+
int abx500_set_register_interruptible(struct device *dev, u8 bank, u8 reg,
u8 value);
int abx500_get_register_interruptible(struct device *dev, u8 bank, u8 reg,
projects / ~andy / linux / blobdiff