__u32 cmd;
__u32 supported; /* Features this interface supports */
__u32 advertising; /* Features this interface advertises */
- __u16 speed; /* The forced speed, 10Mb, 100Mb, gigabit */
+ __u16 speed; /* The forced speed (lower bits) in
+ * Mbps. Please use
+ * ethtool_cmd_speed()/_set() to
+ * access it */
__u8 duplex; /* Duplex, half or full */
__u8 port; /* Which connector port */
__u8 phy_address;
__u8 mdio_support;
__u32 maxtxpkt; /* Tx pkts before generating tx int */
__u32 maxrxpkt; /* Rx pkts before generating rx int */
- __u16 speed_hi;
+ __u16 speed_hi; /* The forced speed (upper
+ * bits) in Mbps. Please use
+ * ethtool_cmd_speed()/_set() to
+ * access it */
__u8 eth_tp_mdix;
__u8 reserved2;
__u32 lp_advertising; /* Features the link partner advertises */
};
static inline void ethtool_cmd_speed_set(struct ethtool_cmd *ep,
- __u32 speed)
+ __u32 speed)
{
ep->speed = (__u16)speed;
ep->speed_hi = (__u16)(speed >> 16);
}
-static inline __u32 ethtool_cmd_speed(struct ethtool_cmd *ep)
+static inline __u32 ethtool_cmd_speed(const struct ethtool_cmd *ep)
{
return (ep->speed_hi << 16) | ep->speed;
}
__u32 tx_pending;
};
+/**
+ * struct ethtool_channels - configuring number of network channel
+ * @cmd: ETHTOOL_{G,S}CHANNELS
+ * @max_rx: Read only. Maximum number of receive channel the driver support.
+ * @max_tx: Read only. Maximum number of transmit channel the driver support.
+ * @max_other: Read only. Maximum number of other channel the driver support.
+ * @max_combined: Read only. Maximum number of combined channel the driver
+ * support. Set of queues RX, TX or other.
+ * @rx_count: Valid values are in the range 1 to the max_rx.
+ * @tx_count: Valid values are in the range 1 to the max_tx.
+ * @other_count: Valid values are in the range 1 to the max_other.
+ * @combined_count: Valid values are in the range 1 to the max_combined.
+ *
+ * This can be used to configure RX, TX and other channels.
+ */
+
+struct ethtool_channels {
+ __u32 cmd;
+ __u32 max_rx;
+ __u32 max_tx;
+ __u32 max_other;
+ __u32 max_combined;
+ __u32 rx_count;
+ __u32 tx_count;
+ __u32 other_count;
+ __u32 combined_count;
+};
+
/* for configuring link flow control parameters */
struct ethtool_pauseparam {
__u32 cmd; /* ETHTOOL_{G,S}PAUSEPARAM */
char data[ETHTOOL_FLASH_MAX_FILENAME];
};
+/**
+ * struct ethtool_dump - used for retrieving, setting device dump
+ * @cmd: Command number - %ETHTOOL_GET_DUMP_FLAG, %ETHTOOL_GET_DUMP_DATA, or
+ * %ETHTOOL_SET_DUMP
+ * @version: FW version of the dump, filled in by driver
+ * @flag: driver dependent flag for dump setting, filled in by driver during
+ * get and filled in by ethtool for set operation
+ * @len: length of dump data, used as the length of the user buffer on entry to
+ * %ETHTOOL_GET_DUMP_DATA and this is returned as dump length by driver
+ * for %ETHTOOL_GET_DUMP_FLAG command
+ * @data: data collected for get dump data operation
+ */
+struct ethtool_dump {
+ __u32 cmd;
+ __u32 version;
+ __u32 flag;
+ __u32 len;
+ __u8 data[0];
+};
+
/* for returning and changing feature sets */
/**
/**
* struct ethtool_ops - optional netdev operations
* @get_settings: Get various device settings including Ethernet link
- * settings. Returns a negative error code or zero.
+ * settings. The @cmd parameter is expected to have been cleared
+ * before get_settings is called. Returns a negative error code or
+ * zero.
* @set_settings: Set various device settings including Ethernet link
* settings. Returns a negative error code or zero.
* @get_drvinfo: Report driver/device information. Should only set the
* attached to it. The implementation may update the indicator
* asynchronously or synchronously, but in either case it must return
* quickly. It is initially called with the argument %ETHTOOL_ID_ACTIVE,
- * and must either activate asynchronous updates or return -%EINVAL.
- * If it returns -%EINVAL then it will be called again at intervals with
+ * and must either activate asynchronous updates and return zero, return
+ * a negative error or return a positive frequency for synchronous
+ * indication (e.g. 1 for one on/off cycle per second). If it returns
+ * a frequency then it will be called again at intervals with the
* argument %ETHTOOL_ID_ON or %ETHTOOL_ID_OFF and should set the state of
* the indicator accordingly. Finally, it is called with the argument
* %ETHTOOL_ID_INACTIVE and must deactivate the indicator. Returns a
* negative error code or zero.
- * @phys_id: Deprecated in favour of @set_phys_id.
- * Identify the physical device, e.g. by flashing an LED
- * attached to it until interrupted by a signal or the given time
- * (in seconds) elapses. If the given time is zero, use a default
- * time limit. Returns a negative error code or zero. Being
- * interrupted by a signal is not an error.
* @get_ethtool_stats: Return extended statistics about the device.
* This is only useful if the device maintains statistics not
* included in &struct rtnl_link_stats64.
* Returns a negative error code or zero.
* @set_rxfh_indir: Set the contents of the RX flow hash indirection table.
* Returns a negative error code or zero.
+ * @get_channels: Get number of channels.
+ * @set_channels: Set number of channels. Returns a negative error code or
+ * zero.
+ * @get_dump_flag: Get dump flag indicating current dump length, version,
+ * and flag of the device.
+ * @get_dump_data: Get dump data.
+ * @set_dump: Set dump specific flags to the device.
*
* All operations are optional (i.e. the function pointer may be set
* to %NULL) and callers must take this into account. Callers must
void (*self_test)(struct net_device *, struct ethtool_test *, u64 *);
void (*get_strings)(struct net_device *, u32 stringset, u8 *);
int (*set_phys_id)(struct net_device *, enum ethtool_phys_id_state);
- int (*phys_id)(struct net_device *, u32);
void (*get_ethtool_stats)(struct net_device *,
struct ethtool_stats *, u64 *);
int (*begin)(struct net_device *);
struct ethtool_rxfh_indir *);
int (*set_rxfh_indir)(struct net_device *,
const struct ethtool_rxfh_indir *);
+ void (*get_channels)(struct net_device *, struct ethtool_channels *);
+ int (*set_channels)(struct net_device *, struct ethtool_channels *);
+ int (*get_dump_flag)(struct net_device *, struct ethtool_dump *);
+ int (*get_dump_data)(struct net_device *,
+ struct ethtool_dump *, void *);
+ int (*set_dump)(struct net_device *, struct ethtool_dump *);
+
};
#endif /* __KERNEL__ */
#define ETHTOOL_GFEATURES 0x0000003a /* Get device offload settings */
#define ETHTOOL_SFEATURES 0x0000003b /* Change device offload settings */
+#define ETHTOOL_GCHANNELS 0x0000003c /* Get no of channels */
+#define ETHTOOL_SCHANNELS 0x0000003d /* Set no of channels */
+#define ETHTOOL_SET_DUMP 0x0000003e /* Set dump settings */
+#define ETHTOOL_GET_DUMP_FLAG 0x0000003f /* Get dump settings */
+#define ETHTOOL_GET_DUMP_DATA 0x00000040 /* Get dump data */
/* compatibility with older code */
#define SPARC_ETH_GSET ETHTOOL_GSET
#define SUPPORTED_10000baseKX4_Full (1 << 18)
#define SUPPORTED_10000baseKR_Full (1 << 19)
#define SUPPORTED_10000baseR_FEC (1 << 20)
+#define SUPPORTED_20000baseMLD2_Full (1 << 21)
+#define SUPPORTED_20000baseKR2_Full (1 << 22)
/* Indicates what features are advertised by the interface. */
#define ADVERTISED_10baseT_Half (1 << 0)
#define ADVERTISED_10000baseKX4_Full (1 << 18)
#define ADVERTISED_10000baseKR_Full (1 << 19)
#define ADVERTISED_10000baseR_FEC (1 << 20)
+#define ADVERTISED_20000baseMLD2_Full (1 << 21)
+#define ADVERTISED_20000baseKR2_Full (1 << 22)
/* The following are all involved in forcing a particular link
* mode for the device for setting things. When getting the
projects / ~andy / linux / blobdiff