comment "USB Host-to-Host Cables"
depends on USB_USBNET
-config USB_ALI_M5632
- boolean "ALi M5632 based 'USB 2.0 Data Link' cables"
- depends on USB_USBNET
- default y
- help
- Choose this option if you're using a host-to-host cable
- based on this design, which supports USB 2.0 high speed.
-
-config USB_AN2720
- boolean "AnchorChips 2720 based cables (Xircom PGUNET, ...)"
- depends on USB_USBNET
- default y
- help
- Choose this option if you're using a host-to-host cable
- based on this design. Note that AnchorChips is now a
- Cypress brand.
-
-config USB_BELKIN
- boolean "eTEK based host-to-host cables (Advance, Belkin, ...)"
- depends on USB_USBNET
- default y
- help
- Choose this option if you're using a host-to-host cable
- based on this design: two NetChip 2890 chips and an Atmel
- microcontroller, with LEDs that indicate traffic.
-
config USB_GENESYS
boolean "GeneSys GL620USB-A based cables"
default y
Choose this option if you're using a host-to-host cable
with one of these chips.
-config USB_KC2190
- boolean "KT Technology KC2190 based cables (InstaNet)"
- default y
- depends on USB_USBNET && EXPERIMENTAL
- help
- Choose this option if you're using a host-to-host cable
- with one of these chips.
-
comment "Intelligent USB Devices/Gadgets"
depends on USB_USBNET
-config USB_ARMLINUX
- boolean "Embedded ARM Linux links (iPaq, ...)"
- depends on USB_USBNET
- default y
- help
- Choose this option to support the "usb-eth" networking driver
- used by most of the ARM Linux community with device controllers
- such as the SA-11x0 and PXA-25x UDCs, or the tftp capabilities
- in some PXA versions of the "blob" boot loader.
-
- Linux-based "Gumstix" PXA-25x based systems use this protocol
- to talk with other Linux systems.
-
- Although the ROMs shipped with Sharp Zaurus products use a
- different link level framing protocol, you can have them use
- this simpler protocol by installing a different kernel.
-
-config USB_EPSON2888
- boolean "Epson 2888 based firmware (DEVELOPMENT)"
- depends on USB_USBNET
- default y
- help
- Choose this option to support the usb networking links used
- by some sample firmware from Epson.
-
config USB_ZAURUS
boolean "Sharp Zaurus (stock ROMs) and compatible"
depends on USB_USBNET
CDC Ethernet is an implementation option for DOCSIS cable modems
that support USB connectivity, used for non-Microsoft USB hosts.
+ The Linux-USB CDC Ethernet Gadget driver is an open implementation.
This driver should work with at least the following devices:
* Ericsson PipeRider (all variants)
This driver creates an interface named "ethX", where X depends on
what other networking devices you have in use.
+
+config USB_NET_CDC_SUBSET
+ tristate "Simple USB Network Links (CDC Ethernet subset)"
+ depends on USB_USBNET
+ help
+ This driver module supports USB network devices that can work
+ without any device-specific information. Select it if you have
+ one of these drivers.
+
+ Note that while many USB host-to-host cables can work in this mode,
+ that may mean not being able to talk to Win32 systems or more
+ commonly not being able to handle certain events (like replugging
+ the host on the other end) very well. Also, these devices will
+ not generally have permanently assigned Ethernet addresses.
+
+config USB_ALI_M5632
+ boolean "ALi M5632 based 'USB 2.0 Data Link' cables"
+ depends on USB_NET_CDC_SUBSET
+ help
+ Choose this option if you're using a host-to-host cable
+ based on this design, which supports USB 2.0 high speed.
+
+config USB_AN2720
+ boolean "AnchorChips 2720 based cables (Xircom PGUNET, ...)"
+ depends on USB_NET_CDC_SUBSET
+ help
+ Choose this option if you're using a host-to-host cable
+ based on this design. Note that AnchorChips is now a
+ Cypress brand.
+
+config USB_BELKIN
+ boolean "eTEK based host-to-host cables (Advance, Belkin, ...)"
+ depends on USB_NET_CDC_SUBSET
+ default y
+ help
+ Choose this option if you're using a host-to-host cable
+ based on this design: two NetChip 2890 chips and an Atmel
+ microcontroller, with LEDs that indicate traffic.
+
+config USB_ARMLINUX
+ boolean "Embedded ARM Linux links (iPaq, ...)"
+ depends on USB_NET_CDC_SUBSET
+ default y
+ help
+ Choose this option to support the "usb-eth" networking driver
+ used by most of the ARM Linux community with device controllers
+ such as the SA-11x0 and PXA-25x UDCs, or the tftp capabilities
+ in some PXA versions of the "blob" boot loader.
+
+ Linux-based "Gumstix" PXA-25x based systems use this protocol
+ to talk with other Linux systems.
+
+ Although the ROMs shipped with Sharp Zaurus products use a
+ different link level framing protocol, you can have them use
+ this simpler protocol by installing a different kernel.
+
+config USB_EPSON2888
+ boolean "Epson 2888 based firmware (DEVELOPMENT)"
+ depends on USB_NET_CDC_SUBSET
+ help
+ Choose this option to support the usb networking links used
+ by some sample firmware from Epson.
+
+
config USB_ZD1201
tristate "USB ZD1201 based Wireless device support"
depends on NET_RADIO
projects / ~andy / linux / blobdiff