/******************************************************************************
*function: This function read register from RF chip
* input: net_device dev
- * RF90_RADIO_PATH_E eRFPath //radio path of A/B/C/D
+ * RF90_RADIO_PATH_E eRFPath //radio path of A/B/C/D
* u32 Offset //target address to be read
* output: none
- * return: u32 readback value
+ * return: u32 readback value
* notice: There are three types of serial operations:(1) Software serial write.(2)Hardware LSSI-Low Speed Serial Interface.(3)Hardware HSSI-High speed serial write. Driver here need to implement (1) and (2)---need more spec for this information.
* ****************************************************************************/
u32 rtl8192_phy_RFSerialRead(struct net_device* dev, RF90_RADIO_PATH_E eRFPath, u32 Offset)
/******************************************************************************
*function: This function write data to RF register
* input: net_device dev
- * RF90_RADIO_PATH_E eRFPath //radio path of A/B/C/D
+ * RF90_RADIO_PATH_E eRFPath //radio path of A/B/C/D
* u32 Offset //target address to be written
* u32 Data //The new register data to be written
* output: none
/******************************************************************************
*function: This function set specific bits to RF register
* input: net_device dev
- * RF90_RADIO_PATH_E eRFPath //radio path of A/B/C/D
+ * RF90_RADIO_PATH_E eRFPath //radio path of A/B/C/D
* u32 RegAddr //target addr to be modified
* u32 BitMask //taget bit pos in the addr to be modified
* u32 Data //value to be write
/******************************************************************************
*function: This function is to write register and then readback to make sure whether BB and RF is OK
* input: net_device dev
- * HW90_BLOCK_E CheckBlock
- * RF90_RADIO_PATH_E eRFPath //only used when checkblock is HW90_BLOCK_RF
+ * HW90_BLOCK_E CheckBlock
+ * RF90_RADIO_PATH_E eRFPath //only used when checkblock is HW90_BLOCK_RF
* output: none
* return: return whether BB and RF is ok(0:OK; 1:Fail)
* notice: This function may be removed in the ASIC
u8 ret = 0;
switch(eRFPath){
- case RF90_PATH_A:
- for(i = 0;i<RadioA_ArrayLength; i=i+2){
-
- if(rtl819XRadioA_Array[i] == 0xfe){
- mdelay(100);
- continue;
- }
- rtl8192_phy_SetRFReg(dev, eRFPath, rtl819XRadioA_Array[i], bMask12Bits, rtl819XRadioA_Array[i+1]);
- mdelay(1);
+ case RF90_PATH_A:
+ for(i = 0;i<RadioA_ArrayLength; i=i+2){
+ if(rtl819XRadioA_Array[i] == 0xfe){
+ mdelay(100);
+ continue;
}
- break;
- case RF90_PATH_B:
- for(i = 0;i<RadioB_ArrayLength; i=i+2){
+ rtl8192_phy_SetRFReg(dev, eRFPath, rtl819XRadioA_Array[i], bMask12Bits, rtl819XRadioA_Array[i+1]);
+ mdelay(1);
- if(rtl819XRadioB_Array[i] == 0xfe){
- mdelay(100);
- continue;
- }
- rtl8192_phy_SetRFReg(dev, eRFPath, rtl819XRadioB_Array[i], bMask12Bits, rtl819XRadioB_Array[i+1]);
- mdelay(1);
+ }
+ break;
+ case RF90_PATH_B:
+ for(i = 0;i<RadioB_ArrayLength; i=i+2){
+ if(rtl819XRadioB_Array[i] == 0xfe){
+ mdelay(100);
+ continue;
}
- break;
- case RF90_PATH_C:
- for(i = 0;i<RadioC_ArrayLength; i=i+2){
+ rtl8192_phy_SetRFReg(dev, eRFPath, rtl819XRadioB_Array[i], bMask12Bits, rtl819XRadioB_Array[i+1]);
+ mdelay(1);
- if(rtl819XRadioC_Array[i] == 0xfe){
- mdelay(100);
- continue;
- }
- rtl8192_phy_SetRFReg(dev, eRFPath, rtl819XRadioC_Array[i], bMask12Bits, rtl819XRadioC_Array[i+1]);
- mdelay(1);
+ }
+ break;
+ case RF90_PATH_C:
+ for(i = 0;i<RadioC_ArrayLength; i=i+2){
+ if(rtl819XRadioC_Array[i] == 0xfe){
+ mdelay(100);
+ continue;
}
- break;
- case RF90_PATH_D:
- for(i = 0;i<RadioD_ArrayLength; i=i+2){
+ rtl8192_phy_SetRFReg(dev, eRFPath, rtl819XRadioC_Array[i], bMask12Bits, rtl819XRadioC_Array[i+1]);
+ mdelay(1);
- if(rtl819XRadioD_Array[i] == 0xfe){
- mdelay(100);
- continue;
- }
- rtl8192_phy_SetRFReg(dev, eRFPath, rtl819XRadioD_Array[i], bMask12Bits, rtl819XRadioD_Array[i+1]);
- mdelay(1);
+ }
+ break;
+ case RF90_PATH_D:
+ for(i = 0;i<RadioD_ArrayLength; i=i+2){
+ if(rtl819XRadioD_Array[i] == 0xfe){
+ mdelay(100);
+ continue;
}
- break;
- default:
- break;
+ rtl8192_phy_SetRFReg(dev, eRFPath, rtl819XRadioD_Array[i], bMask12Bits, rtl819XRadioD_Array[i+1]);
+ mdelay(1);
+
+ }
+ break;
+ default:
+ break;
}
return ret;
/******************************************************************************
*function: This function set Tx Power of the channel
* input: struct net_device *dev
- * u8 channel
+ * u8 channel
* output: none
* return: none
* Note:
/******************************************************************************
*function: This function set RF state on or off
* input: struct net_device *dev
- * RT_RF_POWER_STATE eRFPowerState //Power State to set
+ * RT_RF_POWER_STATE eRFPowerState //Power State to set
* output: none
* return: none
* Note:
/****************************************************************************************
*function: This function set command table variable(struct SwChnlCmd).
- * input: SwChnlCmd* CmdTable //table to be set.
- * u32 CmdTableIdx //variable index in table to be set
- * u32 CmdTableSz //table size.
- * SwChnlCmdID CmdID //command ID to set.
+ * input: SwChnlCmd* CmdTable //table to be set.
+ * u32 CmdTableIdx //variable index in table to be set
+ * u32 CmdTableSz //table size.
+ * SwChnlCmdID CmdID //command ID to set.
* u32 Para1
* u32 Para2
* u32 msDelay
/******************************************************************************
*function: This function set channel step by step
* input: struct net_device *dev
- * u8 channel
- * u8* stage //3 stages
- * u8* step //
- * u32* delay //whether need to delay
+ * u8 channel
+ * u8* stage //3 stages
+ * u8* step //
+ * u32* delay //whether need to delay
* output: store new stage, step and delay for next step(combine with function above)
* return: true if finished, false otherwise
* Note: Wait for simpler function to replace it //wb
/******************************************************************************
*function: This function does actually set channel work
* input: struct net_device *dev
- * u8 channel
+ * u8 channel
* output: none
* return: noin
* Note: We should not call this function directly
/******************************************************************************
*function: This function scheduled actual work item to set channel
* input: net_device dev
- * u8 channel //channel to set
+ * u8 channel //channel to set
* output: none
* return: return code show if workitem is scheduled(1:pass, 0:fail)
* Note: Delay may be required for RF configuration
/******************************************************************************
*function: Callback routine of the work item for set bandwidth mode.
* input: struct net_device *dev
- * HT_CHANNEL_WIDTH Bandwidth //20M or 40M
- * HT_EXTCHNL_OFFSET Offset //Upper, Lower, or Don't care
+ * HT_CHANNEL_WIDTH Bandwidth //20M or 40M
+ * HT_EXTCHNL_OFFSET Offset //Upper, Lower, or Don't care
* output: none
* return: none
* Note: I doubt whether SetBWModeInProgress flag is necessary as we can
- * test whether current work in the queue or not.//do I?
+ * test whether current work in the queue or not.//do I?
* ***************************************************************************/
void rtl8192_SetBWModeWorkItem(struct net_device *dev)
{
/******************************************************************************
*function: This function schedules bandwidth switch work.
* input: struct net_device *dev
- * HT_CHANNEL_WIDTH Bandwidth //20M or 40M
- * HT_EXTCHNL_OFFSET Offset //Upper, Lower, or Don't care
+ * HT_CHANNEL_WIDTH Bandwidth //20M or 40M
+ * HT_EXTCHNL_OFFSET Offset //Upper, Lower, or Don't care
* output: none
* return: none
* Note: I doubt whether SetBWModeInProgress flag is necessary as we can
- * test whether current work in the queue or not.//do I?
+ * test whether current work in the queue or not.//do I?
* ***************************************************************************/
void rtl8192_SetBWMode(struct net_device *dev, HT_CHANNEL_WIDTH Bandwidth, HT_EXTCHNL_OFFSET Offset)
{
break;
}
}
-
projects / ~andy / linux / blobdiff