#include <linux/mfd/abx500/ab8500.h>
#include <linux/mfd/abx500/ab8500-bm.h>
#include <linux/mfd/abx500/ab8500-gpadc.h>
+#include <linux/kernel.h>
#define MILLI_TO_MICRO 1000
#define FG_LSB_IN_MA 1627
#define NBR_AVG_SAMPLES 20
-#define LOW_BAT_CHECK_INTERVAL (2 * HZ)
+#define LOW_BAT_CHECK_INTERVAL (HZ / 16) /* 62.5 ms */
#define VALID_CAPACITY_SEC (45 * 60) /* 45 minutes */
#define BATT_OK_MIN 2360 /* mV */
int sum;
};
+struct ab8500_fg_cap_scaling {
+ bool enable;
+ int cap_to_scale[2];
+ int disable_cap_level;
+ int scaled_cap;
+};
+
struct ab8500_fg_battery_capacity {
int max_mah_design;
int max_mah;
int prev_percent;
int prev_level;
int user_mah;
+ struct ab8500_fg_cap_scaling cap_scale;
};
struct ab8500_fg_flags {
* @recovery_cnt: Counter for recovery mode
* @high_curr_cnt: Counter for high current mode
* @init_cnt: Counter for init mode
+ * @low_bat_cnt Counter for number of consecutive low battery measures
+ * @nbr_cceoc_irq_cnt Counter for number of CCEOC irqs received since enabled
* @recovery_needed: Indicate if recovery is needed
* @high_curr_mode: Indicate if we're in high current mode
* @init_capacity: Indicate if initial capacity measuring should be done
* @calib_state State during offset calibration
* @discharge_state: Current discharge state
* @charge_state: Current charge state
+ * @ab8500_fg_started Completion struct used for the instant current start
* @ab8500_fg_complete Completion struct used for the instant current reading
* @flags: Structure for information about events triggered
* @bat_cap: Structure for battery capacity specific parameters
* @avg_cap: Average capacity filter
* @parent: Pointer to the struct ab8500
* @gpadc: Pointer to the struct gpadc
- * @bat: Pointer to the abx500_bm platform data
+ * @bm: Platform specific battery management information
* @fg_psy: Structure that holds the FG specific battery properties
* @fg_wq: Work queue for running the FG algorithm
* @fg_periodic_work: Work to run the FG algorithm periodically
int recovery_cnt;
int high_curr_cnt;
int init_cnt;
+ int low_bat_cnt;
+ int nbr_cceoc_irq_cnt;
bool recovery_needed;
bool high_curr_mode;
bool init_capacity;
enum ab8500_fg_calibration_state calib_state;
enum ab8500_fg_discharge_state discharge_state;
enum ab8500_fg_charge_state charge_state;
+ struct completion ab8500_fg_started;
struct completion ab8500_fg_complete;
struct ab8500_fg_flags flags;
struct ab8500_fg_battery_capacity bat_cap;
struct ab8500_fg_avg_cap avg_cap;
struct ab8500 *parent;
struct ab8500_gpadc *gpadc;
- struct abx500_bm_data *bat;
+ struct abx500_bm_data *bm;
struct power_supply fg_psy;
struct workqueue_struct *fg_wq;
struct delayed_work fg_periodic_work;
/*
* We want to know if we're in low current mode
*/
- if (curr > -di->bat->fg_params->high_curr_threshold)
+ if (curr > -di->bm->fg_params->high_curr_threshold)
return true;
else
return false;
di->flags.fg_enabled = true;
} else {
/* Clear any pending read requests */
- ret = abx500_set_register_interruptible(di->dev,
- AB8500_GAS_GAUGE, AB8500_GASG_CC_CTRL_REG, 0);
+ ret = abx500_mask_and_set_register_interruptible(di->dev,
+ AB8500_GAS_GAUGE, AB8500_GASG_CC_CTRL_REG,
+ (RESET_ACCU | READ_REQ), 0);
if (ret)
goto cc_err;
* Note: This is part "one" and has to be called before
* ab8500_fg_inst_curr_finalize()
*/
- int ab8500_fg_inst_curr_start(struct ab8500_fg *di)
+int ab8500_fg_inst_curr_start(struct ab8500_fg *di)
{
u8 reg_val;
int ret;
mutex_lock(&di->cc_lock);
+ di->nbr_cceoc_irq_cnt = 0;
ret = abx500_get_register_interruptible(di->dev, AB8500_RTC,
AB8500_RTC_CC_CONF_REG, ®_val);
if (ret < 0)
}
/* Return and WFI */
+ INIT_COMPLETION(di->ab8500_fg_started);
INIT_COMPLETION(di->ab8500_fg_complete);
enable_irq(di->irq);
return ret;
}
+/**
+ * ab8500_fg_inst_curr_started() - check if fg conversion has started
+ * @di: pointer to the ab8500_fg structure
+ *
+ * Returns 1 if conversion started, 0 if still waiting
+ */
+int ab8500_fg_inst_curr_started(struct ab8500_fg *di)
+{
+ return completion_done(&di->ab8500_fg_started);
+}
+
/**
* ab8500_fg_inst_curr_done() - check if fg conversion is done
* @di: pointer to the ab8500_fg structure
int timeout;
if (!completion_done(&di->ab8500_fg_complete)) {
- timeout = wait_for_completion_timeout(&di->ab8500_fg_complete,
+ timeout = wait_for_completion_timeout(
+ &di->ab8500_fg_complete,
INS_CURR_TIMEOUT);
dev_dbg(di->dev, "Finalize time: %d ms\n",
((INS_CURR_TIMEOUT - timeout) * 1000) / HZ);
if (!timeout) {
ret = -ETIME;
disable_irq(di->irq);
+ di->nbr_cceoc_irq_cnt = 0;
dev_err(di->dev, "completion timed out [%d]\n",
__LINE__);
goto fail;
}
disable_irq(di->irq);
+ di->nbr_cceoc_irq_cnt = 0;
ret = abx500_mask_and_set_register_interruptible(di->dev,
AB8500_GAS_GAUGE, AB8500_GASG_CC_CTRL_REG,
* 112.9nAh assumes 10mOhm, but fg_res is in 0.1mOhm
*/
val = (val * QLSB_NANO_AMP_HOURS_X10 * 36 * 4) /
- (1000 * di->bat->fg_res);
+ (1000 * di->bm->fg_res);
if (di->turn_off_fg) {
dev_dbg(di->dev, "%s Disable FG\n", __func__);
int ab8500_fg_inst_curr_blocking(struct ab8500_fg *di)
{
int ret;
+ int timeout;
int res = 0;
ret = ab8500_fg_inst_curr_start(di);
return 0;
}
+ /* Wait for CC to actually start */
+ if (!completion_done(&di->ab8500_fg_started)) {
+ timeout = wait_for_completion_timeout(
+ &di->ab8500_fg_started,
+ INS_CURR_TIMEOUT);
+ dev_dbg(di->dev, "Start time: %d ms\n",
+ ((INS_CURR_TIMEOUT - timeout) * 1000) / HZ);
+ if (!timeout) {
+ ret = -ETIME;
+ dev_err(di->dev, "completion timed out [%d]\n",
+ __LINE__);
+ goto fail;
+ }
+ }
+
ret = ab8500_fg_inst_curr_finalize(di, &res);
if (ret) {
dev_err(di->dev, "Failed to finalize fg_inst\n");
return 0;
}
+ dev_dbg(di->dev, "%s instant current: %d", __func__, res);
return res;
+fail:
+ disable_irq(di->irq);
+ mutex_unlock(&di->cc_lock);
+ return ret;
}
/**
* 112.9nAh assumes 10mOhm, but fg_res is in 0.1mOhm
*/
di->accu_charge = (val * QLSB_NANO_AMP_HOURS_X10) /
- (100 * di->bat->fg_res);
+ (100 * di->bm->fg_res);
/*
* Convert to unit value in mA
- * Full scale input voltage is
- * 66.660mV => LSB = 66.660mV/(4096*res) = 1.627mA
- * Given a 250ms conversion cycle time the LSB corresponds
- * to 112.9 nAh. Convert to current by dividing by the conversion
+ * by dividing by the conversion
* time in hours (= samples / (3600 * 4)h)
- * 112.9nAh assumes 10mOhm, but fg_res is in 0.1mOhm
+ * and multiply with 1000
*/
di->avg_curr = (val * QLSB_NANO_AMP_HOURS_X10 * 36) /
- (1000 * di->bat->fg_res * (di->fg_samples / 4));
+ (1000 * di->bm->fg_res * (di->fg_samples / 4));
di->flags.conv_done = true;
queue_work(di->fg_wq, &di->fg_work);
+ dev_dbg(di->dev, "fg_res: %d, fg_samples: %d, gasg: %d, accu_charge: %d \n",
+ di->bm->fg_res, di->fg_samples, val, di->accu_charge);
return;
exit:
dev_err(di->dev,
struct abx500_v_to_cap *tbl;
int cap = 0;
- tbl = di->bat->bat_type[di->bat->batt_id].v_to_cap_tbl,
- tbl_size = di->bat->bat_type[di->bat->batt_id].n_v_cap_tbl_elements;
+ tbl = di->bm->bat_type[di->bm->batt_id].v_to_cap_tbl,
+ tbl_size = di->bm->bat_type[di->bm->batt_id].n_v_cap_tbl_elements;
for (i = 0; i < tbl_size; ++i) {
if (voltage > tbl[i].voltage)
struct batres_vs_temp *tbl;
int resist = 0;
- tbl = di->bat->bat_type[di->bat->batt_id].batres_tbl;
- tbl_size = di->bat->bat_type[di->bat->batt_id].n_batres_tbl_elements;
+ tbl = di->bm->bat_type[di->bm->batt_id].batres_tbl;
+ tbl_size = di->bm->bat_type[di->bm->batt_id].n_batres_tbl_elements;
for (i = 0; i < tbl_size; ++i) {
if (di->bat_temp / 10 > tbl[i].temp)
dev_dbg(di->dev, "%s Temp: %d battery internal resistance: %d"
" fg resistance %d, total: %d (mOhm)\n",
- __func__, di->bat_temp, resist, di->bat->fg_res / 10,
- (di->bat->fg_res / 10) + resist);
+ __func__, di->bat_temp, resist, di->bm->fg_res / 10,
+ (di->bm->fg_res / 10) + resist);
/* fg_res variable is in 0.1mOhm */
- resist += di->bat->fg_res / 10;
+ resist += di->bm->fg_res / 10;
return resist;
}
do {
vbat += ab8500_fg_bat_voltage(di);
i++;
- msleep(5);
+ usleep_range(5000, 6000);
} while (!ab8500_fg_inst_curr_done(di));
ab8500_fg_inst_curr_finalize(di, &di->inst_curr);
{
int ret, percent;
- percent = di->bat_cap.permille / 10;
+ percent = DIV_ROUND_CLOSEST(di->bat_cap.permille, 10);
- if (percent <= di->bat->cap_levels->critical ||
+ if (percent <= di->bm->cap_levels->critical ||
di->flags.low_bat)
ret = POWER_SUPPLY_CAPACITY_LEVEL_CRITICAL;
- else if (percent <= di->bat->cap_levels->low)
+ else if (percent <= di->bm->cap_levels->low)
ret = POWER_SUPPLY_CAPACITY_LEVEL_LOW;
- else if (percent <= di->bat->cap_levels->normal)
+ else if (percent <= di->bm->cap_levels->normal)
ret = POWER_SUPPLY_CAPACITY_LEVEL_NORMAL;
- else if (percent <= di->bat->cap_levels->high)
+ else if (percent <= di->bm->cap_levels->high)
ret = POWER_SUPPLY_CAPACITY_LEVEL_HIGH;
else
ret = POWER_SUPPLY_CAPACITY_LEVEL_FULL;
return ret;
}
+/**
+ * ab8500_fg_calculate_scaled_capacity() - Capacity scaling
+ * @di: pointer to the ab8500_fg structure
+ *
+ * Calculates the capacity to be shown to upper layers. Scales the capacity
+ * to have 100% as a reference from the actual capacity upon removal of charger
+ * when charging is in maintenance mode.
+ */
+static int ab8500_fg_calculate_scaled_capacity(struct ab8500_fg *di)
+{
+ struct ab8500_fg_cap_scaling *cs = &di->bat_cap.cap_scale;
+ int capacity = di->bat_cap.prev_percent;
+
+ if (!cs->enable)
+ return capacity;
+
+ /*
+ * As long as we are in fully charge mode scale the capacity
+ * to show 100%.
+ */
+ if (di->flags.fully_charged) {
+ cs->cap_to_scale[0] = 100;
+ cs->cap_to_scale[1] =
+ max(capacity, di->bm->fg_params->maint_thres);
+ dev_dbg(di->dev, "Scale cap with %d/%d\n",
+ cs->cap_to_scale[0], cs->cap_to_scale[1]);
+ }
+
+ /* Calculates the scaled capacity. */
+ if ((cs->cap_to_scale[0] != cs->cap_to_scale[1])
+ && (cs->cap_to_scale[1] > 0))
+ capacity = min(100,
+ DIV_ROUND_CLOSEST(di->bat_cap.prev_percent *
+ cs->cap_to_scale[0],
+ cs->cap_to_scale[1]));
+
+ if (di->flags.charging) {
+ if (capacity < cs->disable_cap_level) {
+ cs->disable_cap_level = capacity;
+ dev_dbg(di->dev, "Cap to stop scale lowered %d%%\n",
+ cs->disable_cap_level);
+ } else if (!di->flags.fully_charged) {
+ if (di->bat_cap.prev_percent >=
+ cs->disable_cap_level) {
+ dev_dbg(di->dev, "Disabling scaled capacity\n");
+ cs->enable = false;
+ capacity = di->bat_cap.prev_percent;
+ } else {
+ dev_dbg(di->dev,
+ "Waiting in cap to level %d%%\n",
+ cs->disable_cap_level);
+ capacity = cs->disable_cap_level;
+ }
+ }
+ }
+
+ return capacity;
+}
+
+/**
+ * ab8500_fg_update_cap_scalers() - Capacity scaling
+ * @di: pointer to the ab8500_fg structure
+ *
+ * To be called when state change from charge<->discharge to update
+ * the capacity scalers.
+ */
+static void ab8500_fg_update_cap_scalers(struct ab8500_fg *di)
+{
+ struct ab8500_fg_cap_scaling *cs = &di->bat_cap.cap_scale;
+
+ if (!cs->enable)
+ return;
+ if (di->flags.charging) {
+ di->bat_cap.cap_scale.disable_cap_level =
+ di->bat_cap.cap_scale.scaled_cap;
+ dev_dbg(di->dev, "Cap to stop scale at charge %d%%\n",
+ di->bat_cap.cap_scale.disable_cap_level);
+ } else {
+ if (cs->scaled_cap != 100) {
+ cs->cap_to_scale[0] = cs->scaled_cap;
+ cs->cap_to_scale[1] = di->bat_cap.prev_percent;
+ } else {
+ cs->cap_to_scale[0] = 100;
+ cs->cap_to_scale[1] =
+ max(di->bat_cap.prev_percent,
+ di->bm->fg_params->maint_thres);
+ }
+
+ dev_dbg(di->dev, "Cap to scale at discharge %d/%d\n",
+ cs->cap_to_scale[0], cs->cap_to_scale[1]);
+ }
+}
+
/**
* ab8500_fg_check_capacity_limits() - Check if capacity has changed
* @di: pointer to the ab8500_fg structure
static void ab8500_fg_check_capacity_limits(struct ab8500_fg *di, bool init)
{
bool changed = false;
+ int percent = DIV_ROUND_CLOSEST(di->bat_cap.permille, 10);
di->bat_cap.level = ab8500_fg_capacity_level(di);
dev_dbg(di->dev, "Battery low, set capacity to 0\n");
di->bat_cap.prev_percent = 0;
di->bat_cap.permille = 0;
+ percent = 0;
di->bat_cap.prev_mah = 0;
di->bat_cap.mah = 0;
changed = true;
} else if (di->flags.fully_charged) {
/*
* We report 100% if algorithm reported fully charged
- * unless capacity drops too much
+ * and show 100% during maintenance charging (scaling).
*/
if (di->flags.force_full) {
- di->bat_cap.prev_percent = di->bat_cap.permille / 10;
+ di->bat_cap.prev_percent = percent;
di->bat_cap.prev_mah = di->bat_cap.mah;
- } else if (!di->flags.force_full &&
- di->bat_cap.prev_percent !=
- (di->bat_cap.permille) / 10 &&
- (di->bat_cap.permille / 10) <
- di->bat->fg_params->maint_thres) {
+
+ changed = true;
+
+ if (!di->bat_cap.cap_scale.enable &&
+ di->bm->capacity_scaling) {
+ di->bat_cap.cap_scale.enable = true;
+ di->bat_cap.cap_scale.cap_to_scale[0] = 100;
+ di->bat_cap.cap_scale.cap_to_scale[1] =
+ di->bat_cap.prev_percent;
+ di->bat_cap.cap_scale.disable_cap_level = 100;
+ }
+ } else if (di->bat_cap.prev_percent != percent) {
dev_dbg(di->dev,
"battery reported full "
"but capacity dropping: %d\n",
- di->bat_cap.permille / 10);
- di->bat_cap.prev_percent = di->bat_cap.permille / 10;
+ percent);
+ di->bat_cap.prev_percent = percent;
di->bat_cap.prev_mah = di->bat_cap.mah;
changed = true;
}
- } else if (di->bat_cap.prev_percent != di->bat_cap.permille / 10) {
- if (di->bat_cap.permille / 10 == 0) {
+ } else if (di->bat_cap.prev_percent != percent) {
+ if (percent == 0) {
/*
* We will not report 0% unless we've got
* the LOW_BAT IRQ, no matter what the FG
di->bat_cap.permille = 1;
di->bat_cap.prev_mah = 1;
di->bat_cap.mah = 1;
+ percent = 1;
changed = true;
} else if (!(!di->flags.charging &&
- (di->bat_cap.permille / 10) >
- di->bat_cap.prev_percent) || init) {
+ percent > di->bat_cap.prev_percent) || init) {
/*
* We do not allow reported capacity to go up
* unless we're charging or if we're in init
dev_dbg(di->dev,
"capacity changed from %d to %d (%d)\n",
di->bat_cap.prev_percent,
- di->bat_cap.permille / 10,
+ percent,
di->bat_cap.permille);
- di->bat_cap.prev_percent = di->bat_cap.permille / 10;
+ di->bat_cap.prev_percent = percent;
di->bat_cap.prev_mah = di->bat_cap.mah;
changed = true;
dev_dbg(di->dev, "capacity not allowed to go up since "
"no charger is connected: %d to %d (%d)\n",
di->bat_cap.prev_percent,
- di->bat_cap.permille / 10,
+ percent,
di->bat_cap.permille);
}
}
if (changed) {
+ if (di->bm->capacity_scaling) {
+ di->bat_cap.cap_scale.scaled_cap =
+ ab8500_fg_calculate_scaled_capacity(di);
+
+ dev_info(di->dev, "capacity=%d (%d)\n",
+ di->bat_cap.prev_percent,
+ di->bat_cap.cap_scale.scaled_cap);
+ }
power_supply_changed(&di->fg_psy);
if (di->flags.fully_charged && di->flags.force_full) {
dev_dbg(di->dev, "Battery full, notifying.\n");
switch (di->charge_state) {
case AB8500_FG_CHARGE_INIT:
di->fg_samples = SEC_TO_SAMPLE(
- di->bat->fg_params->accu_charging);
+ di->bm->fg_params->accu_charging);
ab8500_fg_coulomb_counter(di, true);
ab8500_fg_charge_state_to(di, AB8500_FG_CHARGE_READOUT);
* Read the FG and calculate the new capacity
*/
mutex_lock(&di->cc_lock);
- if (!di->flags.conv_done) {
+ if (!di->flags.conv_done && !di->flags.force_full) {
/* Wasn't the CC IRQ that got us here */
mutex_unlock(&di->cc_lock);
dev_dbg(di->dev, "%s CC conv not done\n",
cap_permille = ab8500_fg_convert_mah_to_permille(di,
di->bat_cap.user_mah);
- lower = di->bat_cap.permille - di->bat->fg_params->user_cap_limit * 10;
- upper = di->bat_cap.permille + di->bat->fg_params->user_cap_limit * 10;
+ lower = di->bat_cap.permille - di->bm->fg_params->user_cap_limit * 10;
+ upper = di->bat_cap.permille + di->bm->fg_params->user_cap_limit * 10;
if (lower < 0)
lower = 0;
case AB8500_FG_DISCHARGE_INIT:
/* We use the FG IRQ to work on */
di->init_cnt = 0;
- di->fg_samples = SEC_TO_SAMPLE(di->bat->fg_params->init_timer);
+ di->fg_samples = SEC_TO_SAMPLE(di->bm->fg_params->init_timer);
ab8500_fg_coulomb_counter(di, true);
ab8500_fg_discharge_state_to(di,
AB8500_FG_DISCHARGE_INITMEASURING);
* samples to get an initial capacity.
* Then go to READOUT
*/
- sleep_time = di->bat->fg_params->init_timer;
+ sleep_time = di->bm->fg_params->init_timer;
/* Discard the first [x] seconds */
- if (di->init_cnt >
- di->bat->fg_params->init_discard_time) {
+ if (di->init_cnt > di->bm->fg_params->init_discard_time) {
ab8500_fg_calc_cap_discharge_voltage(di, true);
ab8500_fg_check_capacity_limits(di, true);
}
di->init_cnt += sleep_time;
- if (di->init_cnt > di->bat->fg_params->init_total_time)
+ if (di->init_cnt > di->bm->fg_params->init_total_time)
ab8500_fg_discharge_state_to(di,
AB8500_FG_DISCHARGE_READOUT_INIT);
/* Intentional fallthrough */
case AB8500_FG_DISCHARGE_RECOVERY:
- sleep_time = di->bat->fg_params->recovery_sleep_timer;
+ sleep_time = di->bm->fg_params->recovery_sleep_timer;
/*
* We should check the power consumption
if (ab8500_fg_is_low_curr(di, di->inst_curr)) {
if (di->recovery_cnt >
- di->bat->fg_params->recovery_total_time) {
+ di->bm->fg_params->recovery_total_time) {
di->fg_samples = SEC_TO_SAMPLE(
- di->bat->fg_params->accu_high_curr);
+ di->bm->fg_params->accu_high_curr);
ab8500_fg_coulomb_counter(di, true);
ab8500_fg_discharge_state_to(di,
AB8500_FG_DISCHARGE_READOUT);
di->recovery_cnt += sleep_time;
} else {
di->fg_samples = SEC_TO_SAMPLE(
- di->bat->fg_params->accu_high_curr);
+ di->bm->fg_params->accu_high_curr);
ab8500_fg_coulomb_counter(di, true);
ab8500_fg_discharge_state_to(di,
AB8500_FG_DISCHARGE_READOUT);
case AB8500_FG_DISCHARGE_READOUT_INIT:
di->fg_samples = SEC_TO_SAMPLE(
- di->bat->fg_params->accu_high_curr);
+ di->bm->fg_params->accu_high_curr);
ab8500_fg_coulomb_counter(di, true);
ab8500_fg_discharge_state_to(di,
AB8500_FG_DISCHARGE_READOUT);
if (di->recovery_needed) {
ab8500_fg_discharge_state_to(di,
- AB8500_FG_DISCHARGE_RECOVERY);
+ AB8500_FG_DISCHARGE_INIT_RECOVERY);
queue_delayed_work(di->fg_wq,
&di->fg_periodic_work, 0);
}
di->high_curr_cnt +=
- di->bat->fg_params->accu_high_curr;
+ di->bm->fg_params->accu_high_curr;
if (di->high_curr_cnt >
- di->bat->fg_params->high_curr_time)
+ di->bm->fg_params->high_curr_time)
di->recovery_needed = true;
ab8500_fg_calc_cap_discharge_fg(di);
case AB8500_FG_DISCHARGE_WAKEUP:
ab8500_fg_coulomb_counter(di, true);
- di->inst_curr = ab8500_fg_inst_curr_blocking(di);
-
ab8500_fg_calc_cap_discharge_voltage(di, true);
di->fg_samples = SEC_TO_SAMPLE(
- di->bat->fg_params->accu_high_curr);
+ di->bm->fg_params->accu_high_curr);
ab8500_fg_coulomb_counter(di, true);
ab8500_fg_discharge_state_to(di,
AB8500_FG_DISCHARGE_READOUT);
fg_periodic_work.work);
if (di->init_capacity) {
- /* A dummy read that will return 0 */
- di->inst_curr = ab8500_fg_inst_curr_blocking(di);
/* Get an initial capacity calculation */
ab8500_fg_calc_cap_discharge_voltage(di, true);
ab8500_fg_check_capacity_limits(di, true);
* If we have had a battery over-voltage situation,
* check ovv-bit to see if it should be reset.
*/
- if (di->flags.bat_ovv) {
- ret = abx500_get_register_interruptible(di->dev,
- AB8500_CHARGER, AB8500_CH_STAT_REG,
- ®_value);
- if (ret < 0) {
- dev_err(di->dev, "%s ab8500 read failed\n", __func__);
- return;
- }
- if ((reg_value & BATT_OVV) != BATT_OVV) {
- dev_dbg(di->dev, "Battery recovered from OVV\n");
- di->flags.bat_ovv = false;
+ ret = abx500_get_register_interruptible(di->dev,
+ AB8500_CHARGER, AB8500_CH_STAT_REG,
+ ®_value);
+ if (ret < 0) {
+ dev_err(di->dev, "%s ab8500 read failed\n", __func__);
+ return;
+ }
+ if ((reg_value & BATT_OVV) == BATT_OVV) {
+ if (!di->flags.bat_ovv) {
+ dev_dbg(di->dev, "Battery OVV\n");
+ di->flags.bat_ovv = true;
power_supply_changed(&di->fg_psy);
- return;
}
-
/* Not yet recovered from ovv, reschedule this test */
queue_delayed_work(di->fg_wq, &di->fg_check_hw_failure_work,
- round_jiffies(HZ));
+ HZ);
+ } else {
+ dev_dbg(di->dev, "Battery recovered from OVV\n");
+ di->flags.bat_ovv = false;
+ power_supply_changed(&di->fg_psy);
}
}
vbat = ab8500_fg_bat_voltage(di);
/* Check if LOW_BAT still fulfilled */
- if (vbat < di->bat->fg_params->lowbat_threshold) {
- di->flags.low_bat = true;
- dev_warn(di->dev, "Battery voltage still LOW\n");
-
- /*
- * We need to re-schedule this check to be able to detect
- * if the voltage increases again during charging
- */
- queue_delayed_work(di->fg_wq, &di->fg_low_bat_work,
- round_jiffies(LOW_BAT_CHECK_INTERVAL));
+ if (vbat < di->bm->fg_params->lowbat_threshold) {
+ /* Is it time to shut down? */
+ if (di->low_bat_cnt < 1) {
+ di->flags.low_bat = true;
+ dev_warn(di->dev, "Shut down pending...\n");
+ } else {
+ /*
+ * Else we need to re-schedule this check to be able to detect
+ * if the voltage increases again during charging or
+ * due to decreasing load.
+ */
+ di->low_bat_cnt--;
+ dev_warn(di->dev, "Battery voltage still LOW\n");
+ queue_delayed_work(di->fg_wq, &di->fg_low_bat_work,
+ round_jiffies(LOW_BAT_CHECK_INTERVAL));
+ }
} else {
- di->flags.low_bat = false;
+ di->flags.low_bat_delay = false;
+ di->low_bat_cnt = 10;
dev_warn(di->dev, "Battery voltage OK again\n");
}
/* This is needed to dispatch LOW_BAT */
ab8500_fg_check_capacity_limits(di, false);
-
- /* Set this flag to check if LOW_BAT IRQ still occurs */
- di->flags.low_bat_delay = false;
}
/**
int ret;
int new_val;
- sel0 = di->bat->fg_params->battok_falling_th_sel0;
- sel1 = di->bat->fg_params->battok_raising_th_sel1;
+ sel0 = di->bm->fg_params->battok_falling_th_sel0;
+ sel1 = di->bm->fg_params->battok_raising_th_sel1;
cbp_sel0 = ab8500_fg_battok_calc(di, sel0);
cbp_sel1 = ab8500_fg_battok_calc(di, sel1);
static irqreturn_t ab8500_fg_cc_data_end_handler(int irq, void *_di)
{
struct ab8500_fg *di = _di;
- complete(&di->ab8500_fg_complete);
+ if (!di->nbr_cceoc_irq_cnt) {
+ di->nbr_cceoc_irq_cnt++;
+ complete(&di->ab8500_fg_started);
+ } else {
+ di->nbr_cceoc_irq_cnt = 0;
+ complete(&di->ab8500_fg_complete);
+ }
return IRQ_HANDLED;
}
struct ab8500_fg *di = _di;
dev_dbg(di->dev, "Battery OVV\n");
- di->flags.bat_ovv = true;
- power_supply_changed(&di->fg_psy);
/* Schedule a new HW failure check */
queue_delayed_work(di->fg_wq, &di->fg_check_hw_failure_work, 0);
{
struct ab8500_fg *di = _di;
+ /* Initiate handling in ab8500_fg_low_bat_work() if not already initiated. */
if (!di->flags.low_bat_delay) {
dev_warn(di->dev, "Battery voltage is below LOW threshold\n");
di->flags.low_bat_delay = true;
di->bat_cap.max_mah);
break;
case POWER_SUPPLY_PROP_ENERGY_NOW:
- if (di->flags.batt_unknown && !di->bat->chg_unknown_bat &&
+ if (di->flags.batt_unknown && !di->bm->chg_unknown_bat &&
di->flags.batt_id_received)
val->intval = ab8500_fg_convert_mah_to_uwh(di,
di->bat_cap.max_mah);
val->intval = di->bat_cap.max_mah;
break;
case POWER_SUPPLY_PROP_CHARGE_NOW:
- if (di->flags.batt_unknown && !di->bat->chg_unknown_bat &&
+ if (di->flags.batt_unknown && !di->bm->chg_unknown_bat &&
di->flags.batt_id_received)
val->intval = di->bat_cap.max_mah;
else
val->intval = di->bat_cap.prev_mah;
break;
case POWER_SUPPLY_PROP_CAPACITY:
- if (di->flags.batt_unknown && !di->bat->chg_unknown_bat &&
+ if (di->bm->capacity_scaling)
+ val->intval = di->bat_cap.cap_scale.scaled_cap;
+ else if (di->flags.batt_unknown && !di->bm->chg_unknown_bat &&
di->flags.batt_id_received)
val->intval = 100;
else
val->intval = di->bat_cap.prev_percent;
break;
case POWER_SUPPLY_PROP_CAPACITY_LEVEL:
- if (di->flags.batt_unknown && !di->bat->chg_unknown_bat &&
+ if (di->flags.batt_unknown && !di->bm->chg_unknown_bat &&
di->flags.batt_id_received)
val->intval = POWER_SUPPLY_CAPACITY_LEVEL_UNKNOWN;
else
break;
di->flags.charging = false;
di->flags.fully_charged = false;
+ if (di->bm->capacity_scaling)
+ ab8500_fg_update_cap_scalers(di);
queue_work(di->fg_wq, &di->fg_work);
break;
case POWER_SUPPLY_STATUS_FULL:
queue_work(di->fg_wq, &di->fg_work);
break;
case POWER_SUPPLY_STATUS_CHARGING:
- if (di->flags.charging)
+ if (di->flags.charging &&
+ !di->flags.fully_charged)
break;
di->flags.charging = true;
di->flags.fully_charged = false;
+ if (di->bm->capacity_scaling)
+ ab8500_fg_update_cap_scalers(di);
queue_work(di->fg_wq, &di->fg_work);
break;
};
case POWER_SUPPLY_PROP_TECHNOLOGY:
switch (ext->type) {
case POWER_SUPPLY_TYPE_BATTERY:
- if (!di->flags.batt_id_received) {
+ if (!di->flags.batt_id_received &&
+ di->bm->batt_id != BATTERY_UNKNOWN) {
const struct abx500_battery_type *b;
- b = &(di->bat->bat_type[di->bat->batt_id]);
+ b = &(di->bm->bat_type[di->bm->batt_id]);
di->flags.batt_id_received = true;
case POWER_SUPPLY_PROP_TEMP:
switch (ext->type) {
case POWER_SUPPLY_TYPE_BATTERY:
- if (di->flags.batt_id_received)
- di->bat_temp = ret.intval;
+ if (di->flags.batt_id_received)
+ di->bat_temp = ret.intval;
break;
default:
break;
AB8500_SYS_CTRL2_BLOCK,
AB8500_LOW_BAT_REG,
ab8500_volt_to_regval(
- di->bat->fg_params->lowbat_threshold) << 1 |
+ di->bm->fg_params->lowbat_threshold) << 1 |
LOW_BAT_ENABLE);
if (ret) {
dev_err(di->dev, "%s write failed\n", __func__);
struct ab8500_fg *di = platform_get_drvdata(pdev);
flush_delayed_work(&di->fg_periodic_work);
+ flush_work(&di->fg_work);
+ flush_work(&di->fg_acc_cur_work);
+ flush_delayed_work(&di->fg_reinit_work);
+ flush_delayed_work(&di->fg_low_bat_work);
+ flush_delayed_work(&di->fg_check_hw_failure_work);
/*
* If the FG is enabled we will disable it before going to suspend
static int ab8500_fg_probe(struct platform_device *pdev)
{
struct device_node *np = pdev->dev.of_node;
+ struct abx500_bm_data *plat = pdev->dev.platform_data;
struct ab8500_fg *di;
int i, irq;
int ret = 0;
dev_err(&pdev->dev, "%s no mem for ab8500_fg\n", __func__);
return -ENOMEM;
}
- di->bat = pdev->mfd_cell->platform_data;
- if (!di->bat) {
- if (np) {
- ret = bmdevs_of_probe(&pdev->dev, np, &di->bat);
- if (ret) {
- dev_err(&pdev->dev,
- "failed to get battery information\n");
- return ret;
- }
- } else {
- dev_err(&pdev->dev, "missing dt node for ab8500_fg\n");
- return -EINVAL;
+
+ if (!plat) {
+ dev_err(&pdev->dev, "no battery management data supplied\n");
+ return -EINVAL;
+ }
+ di->bm = plat;
+
+ if (np) {
+ ret = ab8500_bm_of_probe(&pdev->dev, np, di->bm);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to get battery information\n");
+ return ret;
}
- } else {
- dev_info(&pdev->dev, "falling back to legacy platform data\n");
}
mutex_init(&di->cc_lock);
di->fg_psy.external_power_changed = ab8500_fg_external_power_changed;
di->bat_cap.max_mah_design = MILLI_TO_MICRO *
- di->bat->bat_type[di->bat->batt_id].charge_full_design;
+ di->bm->bat_type[di->bm->batt_id].charge_full_design;
di->bat_cap.max_mah = di->bat_cap.max_mah_design;
- di->vbat_nom = di->bat->bat_type[di->bat->batt_id].nominal_voltage;
+ di->vbat_nom = di->bm->bat_type[di->bm->batt_id].nominal_voltage;
di->init_capacity = true;
INIT_DEFERRABLE_WORK(&di->fg_check_hw_failure_work,
ab8500_fg_check_hw_failure_work);
+ /* Reset battery low voltage flag */
+ di->flags.low_bat = false;
+
+ /* Initialize low battery counter */
+ di->low_bat_cnt = 10;
+
/* Initialize OVV, and other registers */
ret = ab8500_fg_init_hw_registers(di);
if (ret) {
goto free_inst_curr_wq;
}
- di->fg_samples = SEC_TO_SAMPLE(di->bat->fg_params->init_timer);
+ di->fg_samples = SEC_TO_SAMPLE(di->bm->fg_params->init_timer);
ab8500_fg_coulomb_counter(di, true);
- /* Initialize completion used to notify completion of inst current */
+ /*
+ * Initialize completion used to notify completion and start
+ * of inst current
+ */
+ init_completion(&di->ab8500_fg_started);
init_completion(&di->ab8500_fg_complete);
/* Register interrupts */
}
di->irq = platform_get_irq_byname(pdev, "CCEOC");
disable_irq(di->irq);
+ di->nbr_cceoc_irq_cnt = 0;
platform_set_drvdata(pdev, di);
projects / ~andy / linux / blobdiff