#define DRV_MODULE_NAME "tg3"
#define PFX DRV_MODULE_NAME ": "
-#define DRV_MODULE_VERSION "3.32"
-#define DRV_MODULE_RELDATE "June 24, 2005"
+#define DRV_MODULE_VERSION "3.36"
+#define DRV_MODULE_RELDATE "August 19, 2005"
#define TG3_DEF_MAC_MODE 0
#define TG3_DEF_RX_MODE 0
/* hardware minimum and maximum for a single frame's data payload */
#define TG3_MIN_MTU 60
#define TG3_MAX_MTU(tp) \
- (!(tp->tg3_flags2 & TG3_FLG2_5705_PLUS) ? 9000 : 1500)
+ ((tp->tg3_flags2 & TG3_FLG2_JUMBO_CAPABLE) ? 9000 : 1500)
/* These numbers seem to be hard coded in the NIC firmware somehow.
* You can't change the ring sizes, but you can change where you place
PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0UL },
{ PCI_VENDOR_ID_BROADCOM, PCI_DEVICE_ID_TIGON3_5753F,
PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0UL },
+ { PCI_VENDOR_ID_BROADCOM, PCI_DEVICE_ID_TIGON3_5780,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0UL },
+ { PCI_VENDOR_ID_BROADCOM, PCI_DEVICE_ID_TIGON3_5780S,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0UL },
{ PCI_VENDOR_ID_BROADCOM, PCI_DEVICE_ID_TIGON3_5781,
PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0UL },
{ PCI_VENDOR_ID_SYSKONNECT, PCI_DEVICE_ID_SYSKONNECT_9DXX,
u32 clock_ctrl = tr32(TG3PCI_CLOCK_CTRL);
u32 orig_clock_ctrl;
+ if (GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5780)
+ return;
+
orig_clock_ctrl = clock_ctrl;
clock_ctrl &= (CLOCK_CTRL_FORCE_CLKRUN |
CLOCK_CTRL_CLKRUN_OENABLE |
if ((tp->phy_id & PHY_ID_MASK) == PHY_ID_BCM5401) {
/* Cannot do read-modify-write on 5401 */
tg3_writephy(tp, MII_TG3_AUX_CTRL, 0x4c20);
- } else if (!(tp->tg3_flags2 & TG3_FLG2_5705_PLUS)) {
+ } else if (tp->tg3_flags2 & TG3_FLG2_JUMBO_CAPABLE) {
u32 phy_reg;
/* Set bit 14 with read-modify-write to preserve other bits */
/* Set phy register 0x10 bit 0 to high fifo elasticity to support
* jumbo frames transmission.
*/
- if (!(tp->tg3_flags2 & TG3_FLG2_5705_PLUS)) {
+ if (tp->tg3_flags2 & TG3_FLG2_JUMBO_CAPABLE) {
u32 phy_reg;
if (!tg3_readphy(tp, MII_TG3_EXT_CTRL, &phy_reg))
tp->link_config.orig_autoneg = tp->link_config.autoneg;
}
- if (!(tp->tg3_flags2 & TG3_FLG2_PHY_SERDES)) {
+ if (!(tp->tg3_flags2 & TG3_FLG2_ANY_SERDES)) {
tp->link_config.speed = SPEED_10;
tp->link_config.duplex = DUPLEX_HALF;
tp->link_config.autoneg = AUTONEG_ENABLE;
CLOCK_CTRL_ALTCLK |
CLOCK_CTRL_PWRDOWN_PLL133);
udelay(40);
+ } else if (GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5780) {
+ /* do nothing */
} else if (!((tp->tg3_flags2 & TG3_FLG2_5750_PLUS) &&
(tp->tg3_flags & TG3_FLAG_ENABLE_ASF))) {
u32 newbits1, newbits2;
u32 old_tx_mode = tp->tx_mode;
if (tp->tg3_flags & TG3_FLAG_PAUSE_AUTONEG) {
+
+ /* Convert 1000BaseX flow control bits to 1000BaseT
+ * bits before resolving flow control.
+ */
+ if (tp->tg3_flags2 & TG3_FLG2_MII_SERDES) {
+ local_adv &= ~(ADVERTISE_PAUSE_CAP |
+ ADVERTISE_PAUSE_ASYM);
+ remote_adv &= ~(LPA_PAUSE_CAP | LPA_PAUSE_ASYM);
+
+ if (local_adv & ADVERTISE_1000XPAUSE)
+ local_adv |= ADVERTISE_PAUSE_CAP;
+ if (local_adv & ADVERTISE_1000XPSE_ASYM)
+ local_adv |= ADVERTISE_PAUSE_ASYM;
+ if (remote_adv & LPA_1000XPAUSE)
+ remote_adv |= LPA_PAUSE_CAP;
+ if (remote_adv & LPA_1000XPAUSE_ASYM)
+ remote_adv |= LPA_PAUSE_ASYM;
+ }
+
if (local_adv & ADVERTISE_PAUSE_CAP) {
if (local_adv & ADVERTISE_PAUSE_ASYM) {
if (remote_adv & LPA_PAUSE_CAP)
return 0;
}
+static int tg3_setup_fiber_mii_phy(struct tg3 *tp, int force_reset)
+{
+ int current_link_up, err = 0;
+ u32 bmsr, bmcr;
+ u16 current_speed;
+ u8 current_duplex;
+
+ tp->mac_mode |= MAC_MODE_PORT_MODE_GMII;
+ tw32_f(MAC_MODE, tp->mac_mode);
+ udelay(40);
+
+ tw32(MAC_EVENT, 0);
+
+ tw32_f(MAC_STATUS,
+ (MAC_STATUS_SYNC_CHANGED |
+ MAC_STATUS_CFG_CHANGED |
+ MAC_STATUS_MI_COMPLETION |
+ MAC_STATUS_LNKSTATE_CHANGED));
+ udelay(40);
+
+ if (force_reset)
+ tg3_phy_reset(tp);
+
+ current_link_up = 0;
+ current_speed = SPEED_INVALID;
+ current_duplex = DUPLEX_INVALID;
+
+ err |= tg3_readphy(tp, MII_BMSR, &bmsr);
+ err |= tg3_readphy(tp, MII_BMSR, &bmsr);
+
+ err |= tg3_readphy(tp, MII_BMCR, &bmcr);
+
+ if ((tp->link_config.autoneg == AUTONEG_ENABLE) && !force_reset &&
+ (tp->tg3_flags2 & TG3_FLG2_PARALLEL_DETECT)) {
+ /* do nothing, just check for link up at the end */
+ } else if (tp->link_config.autoneg == AUTONEG_ENABLE) {
+ u32 adv, new_adv;
+
+ err |= tg3_readphy(tp, MII_ADVERTISE, &adv);
+ new_adv = adv & ~(ADVERTISE_1000XFULL | ADVERTISE_1000XHALF |
+ ADVERTISE_1000XPAUSE |
+ ADVERTISE_1000XPSE_ASYM |
+ ADVERTISE_SLCT);
+
+ /* Always advertise symmetric PAUSE just like copper */
+ new_adv |= ADVERTISE_1000XPAUSE;
+
+ if (tp->link_config.advertising & ADVERTISED_1000baseT_Half)
+ new_adv |= ADVERTISE_1000XHALF;
+ if (tp->link_config.advertising & ADVERTISED_1000baseT_Full)
+ new_adv |= ADVERTISE_1000XFULL;
+
+ if ((new_adv != adv) || !(bmcr & BMCR_ANENABLE)) {
+ tg3_writephy(tp, MII_ADVERTISE, new_adv);
+ bmcr |= BMCR_ANENABLE | BMCR_ANRESTART;
+ tg3_writephy(tp, MII_BMCR, bmcr);
+
+ tw32_f(MAC_EVENT, MAC_EVENT_LNKSTATE_CHANGED);
+ tp->tg3_flags2 |= TG3_FLG2_PHY_JUST_INITTED;
+ tp->tg3_flags2 &= ~TG3_FLG2_PARALLEL_DETECT;
+
+ return err;
+ }
+ } else {
+ u32 new_bmcr;
+
+ bmcr &= ~BMCR_SPEED1000;
+ new_bmcr = bmcr & ~(BMCR_ANENABLE | BMCR_FULLDPLX);
+
+ if (tp->link_config.duplex == DUPLEX_FULL)
+ new_bmcr |= BMCR_FULLDPLX;
+
+ if (new_bmcr != bmcr) {
+ /* BMCR_SPEED1000 is a reserved bit that needs
+ * to be set on write.
+ */
+ new_bmcr |= BMCR_SPEED1000;
+
+ /* Force a linkdown */
+ if (netif_carrier_ok(tp->dev)) {
+ u32 adv;
+
+ err |= tg3_readphy(tp, MII_ADVERTISE, &adv);
+ adv &= ~(ADVERTISE_1000XFULL |
+ ADVERTISE_1000XHALF |
+ ADVERTISE_SLCT);
+ tg3_writephy(tp, MII_ADVERTISE, adv);
+ tg3_writephy(tp, MII_BMCR, bmcr |
+ BMCR_ANRESTART |
+ BMCR_ANENABLE);
+ udelay(10);
+ netif_carrier_off(tp->dev);
+ }
+ tg3_writephy(tp, MII_BMCR, new_bmcr);
+ bmcr = new_bmcr;
+ err |= tg3_readphy(tp, MII_BMSR, &bmsr);
+ err |= tg3_readphy(tp, MII_BMSR, &bmsr);
+ tp->tg3_flags2 &= ~TG3_FLG2_PARALLEL_DETECT;
+ }
+ }
+
+ if (bmsr & BMSR_LSTATUS) {
+ current_speed = SPEED_1000;
+ current_link_up = 1;
+ if (bmcr & BMCR_FULLDPLX)
+ current_duplex = DUPLEX_FULL;
+ else
+ current_duplex = DUPLEX_HALF;
+
+ if (bmcr & BMCR_ANENABLE) {
+ u32 local_adv, remote_adv, common;
+
+ err |= tg3_readphy(tp, MII_ADVERTISE, &local_adv);
+ err |= tg3_readphy(tp, MII_LPA, &remote_adv);
+ common = local_adv & remote_adv;
+ if (common & (ADVERTISE_1000XHALF |
+ ADVERTISE_1000XFULL)) {
+ if (common & ADVERTISE_1000XFULL)
+ current_duplex = DUPLEX_FULL;
+ else
+ current_duplex = DUPLEX_HALF;
+
+ tg3_setup_flow_control(tp, local_adv,
+ remote_adv);
+ }
+ else
+ current_link_up = 0;
+ }
+ }
+
+ tp->mac_mode &= ~MAC_MODE_HALF_DUPLEX;
+ if (tp->link_config.active_duplex == DUPLEX_HALF)
+ tp->mac_mode |= MAC_MODE_HALF_DUPLEX;
+
+ tw32_f(MAC_MODE, tp->mac_mode);
+ udelay(40);
+
+ tw32_f(MAC_EVENT, MAC_EVENT_LNKSTATE_CHANGED);
+
+ tp->link_config.active_speed = current_speed;
+ tp->link_config.active_duplex = current_duplex;
+
+ if (current_link_up != netif_carrier_ok(tp->dev)) {
+ if (current_link_up)
+ netif_carrier_on(tp->dev);
+ else {
+ netif_carrier_off(tp->dev);
+ tp->tg3_flags2 &= ~TG3_FLG2_PARALLEL_DETECT;
+ }
+ tg3_link_report(tp);
+ }
+ return err;
+}
+
+static void tg3_serdes_parallel_detect(struct tg3 *tp)
+{
+ if (tp->tg3_flags2 & TG3_FLG2_PHY_JUST_INITTED) {
+ /* Give autoneg time to complete. */
+ tp->tg3_flags2 &= ~TG3_FLG2_PHY_JUST_INITTED;
+ return;
+ }
+ if (!netif_carrier_ok(tp->dev) &&
+ (tp->link_config.autoneg == AUTONEG_ENABLE)) {
+ u32 bmcr;
+
+ tg3_readphy(tp, MII_BMCR, &bmcr);
+ if (bmcr & BMCR_ANENABLE) {
+ u32 phy1, phy2;
+
+ /* Select shadow register 0x1f */
+ tg3_writephy(tp, 0x1c, 0x7c00);
+ tg3_readphy(tp, 0x1c, &phy1);
+
+ /* Select expansion interrupt status register */
+ tg3_writephy(tp, 0x17, 0x0f01);
+ tg3_readphy(tp, 0x15, &phy2);
+ tg3_readphy(tp, 0x15, &phy2);
+
+ if ((phy1 & 0x10) && !(phy2 & 0x20)) {
+ /* We have signal detect and not receiving
+ * config code words, link is up by parallel
+ * detection.
+ */
+
+ bmcr &= ~BMCR_ANENABLE;
+ bmcr |= BMCR_SPEED1000 | BMCR_FULLDPLX;
+ tg3_writephy(tp, MII_BMCR, bmcr);
+ tp->tg3_flags2 |= TG3_FLG2_PARALLEL_DETECT;
+ }
+ }
+ }
+ else if (netif_carrier_ok(tp->dev) &&
+ (tp->link_config.autoneg == AUTONEG_ENABLE) &&
+ (tp->tg3_flags2 & TG3_FLG2_PARALLEL_DETECT)) {
+ u32 phy2;
+
+ /* Select expansion interrupt status register */
+ tg3_writephy(tp, 0x17, 0x0f01);
+ tg3_readphy(tp, 0x15, &phy2);
+ if (phy2 & 0x20) {
+ u32 bmcr;
+
+ /* Config code words received, turn on autoneg. */
+ tg3_readphy(tp, MII_BMCR, &bmcr);
+ tg3_writephy(tp, MII_BMCR, bmcr | BMCR_ANENABLE);
+
+ tp->tg3_flags2 &= ~TG3_FLG2_PARALLEL_DETECT;
+
+ }
+ }
+}
+
static int tg3_setup_phy(struct tg3 *tp, int force_reset)
{
int err;
if (tp->tg3_flags2 & TG3_FLG2_PHY_SERDES) {
err = tg3_setup_fiber_phy(tp, force_reset);
+ } else if (tp->tg3_flags2 & TG3_FLG2_MII_SERDES) {
+ err = tg3_setup_fiber_mii_phy(tp, force_reset);
} else {
err = tg3_setup_copper_phy(tp, force_reset);
}
map = &tp->rx_std_buffers[dest_idx];
if (src_idx >= 0)
src_map = &tp->rx_std_buffers[src_idx];
- skb_size = RX_PKT_BUF_SZ;
+ skb_size = tp->rx_pkt_buf_sz;
break;
case RXD_OPAQUE_RING_JUMBO:
{
dev->mtu = new_mtu;
- if (new_mtu > ETH_DATA_LEN)
- tp->tg3_flags |= TG3_FLAG_JUMBO_ENABLE;
- else
- tp->tg3_flags &= ~TG3_FLAG_JUMBO_ENABLE;
+ if (new_mtu > ETH_DATA_LEN) {
+ if (GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5780) {
+ tp->tg3_flags2 &= ~TG3_FLG2_TSO_CAPABLE;
+ ethtool_op_set_tso(dev, 0);
+ }
+ else
+ tp->tg3_flags |= TG3_FLAG_JUMBO_RING_ENABLE;
+ } else {
+ if (GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5780)
+ tp->tg3_flags2 |= TG3_FLG2_TSO_CAPABLE;
+ tp->tg3_flags &= ~TG3_FLAG_JUMBO_RING_ENABLE;
+ }
}
static int tg3_change_mtu(struct net_device *dev, int new_mtu)
continue;
pci_unmap_single(tp->pdev,
pci_unmap_addr(rxp, mapping),
- RX_PKT_BUF_SZ - tp->rx_offset,
+ tp->rx_pkt_buf_sz - tp->rx_offset,
PCI_DMA_FROMDEVICE);
dev_kfree_skb_any(rxp->skb);
rxp->skb = NULL;
memset(tp->rx_rcb, 0, TG3_RX_RCB_RING_BYTES(tp));
memset(tp->tx_ring, 0, TG3_TX_RING_BYTES);
+ tp->rx_pkt_buf_sz = RX_PKT_BUF_SZ;
+ if ((GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5780) &&
+ (tp->dev->mtu > ETH_DATA_LEN))
+ tp->rx_pkt_buf_sz = RX_JUMBO_PKT_BUF_SZ;
+
/* Initialize invariants of the rings, we only set this
* stuff once. This works because the card does not
* write into the rx buffer posting rings.
struct tg3_rx_buffer_desc *rxd;
rxd = &tp->rx_std[i];
- rxd->idx_len = (RX_PKT_BUF_SZ - tp->rx_offset - 64)
+ rxd->idx_len = (tp->rx_pkt_buf_sz - tp->rx_offset - 64)
<< RXD_LEN_SHIFT;
rxd->type_flags = (RXD_FLAG_END << RXD_FLAGS_SHIFT);
rxd->opaque = (RXD_OPAQUE_RING_STD |
(i << RXD_OPAQUE_INDEX_SHIFT));
}
- if (tp->tg3_flags & TG3_FLAG_JUMBO_ENABLE) {
+ if (tp->tg3_flags & TG3_FLAG_JUMBO_RING_ENABLE) {
for (i = 0; i < TG3_RX_JUMBO_RING_SIZE; i++) {
struct tg3_rx_buffer_desc *rxd;
break;
}
- if (tp->tg3_flags & TG3_FLAG_JUMBO_ENABLE) {
+ if (tp->tg3_flags & TG3_FLAG_JUMBO_RING_ENABLE) {
for (i = 0; i < tp->rx_jumbo_pending; i++) {
if (tg3_alloc_rx_skb(tp, RXD_OPAQUE_RING_JUMBO,
-1, i) < 0)
val &= ~PCIX_CAPS_RELAXED_ORDERING;
pci_write_config_dword(tp->pdev, TG3PCI_X_CAPS, val);
- tw32(MEMARB_MODE, MEMARB_MODE_ENABLE);
+ if (GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5780) {
+ u32 val;
+
+ /* Chip reset on 5780 will reset MSI enable bit,
+ * so need to restore it.
+ */
+ if (tp->tg3_flags2 & TG3_FLG2_USING_MSI) {
+ u16 ctrl;
+
+ pci_read_config_word(tp->pdev,
+ tp->msi_cap + PCI_MSI_FLAGS,
+ &ctrl);
+ pci_write_config_word(tp->pdev,
+ tp->msi_cap + PCI_MSI_FLAGS,
+ ctrl | PCI_MSI_FLAGS_ENABLE);
+ val = tr32(MSGINT_MODE);
+ tw32(MSGINT_MODE, val | MSGINT_MODE_ENABLE);
+ }
+
+ val = tr32(MEMARB_MODE);
+ tw32(MEMARB_MODE, val | MEMARB_MODE_ENABLE);
+
+ } else
+ tw32(MEMARB_MODE, MEMARB_MODE_ENABLE);
if (tp->pci_chip_rev_id == CHIPREV_ID_5750_A3) {
tg3_stop_fw(tp);
if (tp->tg3_flags2 & TG3_FLG2_PHY_SERDES) {
tp->mac_mode = MAC_MODE_PORT_MODE_TBI;
tw32_f(MAC_MODE, tp->mac_mode);
+ } else if (tp->tg3_flags2 & TG3_FLG2_MII_SERDES) {
+ tp->mac_mode = MAC_MODE_PORT_MODE_GMII;
+ tw32_f(MAC_MODE, tp->mac_mode);
} else
tw32_f(MAC_MODE, 0);
udelay(40);
}
static void __tg3_set_rx_mode(struct net_device *);
-static void tg3_set_coalesce(struct tg3 *tp, struct ethtool_coalesce *ec)
+static void __tg3_set_coalesce(struct tg3 *tp, struct ethtool_coalesce *ec)
{
tw32(HOSTCC_RXCOL_TICKS, ec->rx_coalesce_usecs);
tw32(HOSTCC_TXCOL_TICKS, ec->tx_coalesce_usecs);
}
#endif
- if (!(tp->tg3_flags & TG3_FLAG_JUMBO_ENABLE)) {
+ if (tp->dev->mtu <= ETH_DATA_LEN) {
tw32(BUFMGR_MB_RDMA_LOW_WATER,
tp->bufmgr_config.mbuf_read_dma_low_water);
tw32(BUFMGR_MB_MACRX_LOW_WATER,
/* Setup replenish threshold. */
tw32(RCVBDI_JUMBO_THRESH, tp->rx_jumbo_pending / 8);
- if (tp->tg3_flags & TG3_FLAG_JUMBO_ENABLE) {
+ if (tp->tg3_flags & TG3_FLAG_JUMBO_RING_ENABLE) {
tw32(RCVDBDI_JUMBO_BD + TG3_BDINFO_HOST_ADDR + TG3_64BIT_REG_HIGH,
((u64) tp->rx_jumbo_mapping >> 32));
tw32(RCVDBDI_JUMBO_BD + TG3_BDINFO_HOST_ADDR + TG3_64BIT_REG_LOW,
tw32_rx_mbox(MAILBOX_RCV_STD_PROD_IDX + TG3_64BIT_REG_LOW,
tp->rx_std_ptr);
- tp->rx_jumbo_ptr = (tp->tg3_flags & TG3_FLAG_JUMBO_ENABLE) ?
+ tp->rx_jumbo_ptr = (tp->tg3_flags & TG3_FLAG_JUMBO_RING_ENABLE) ?
tp->rx_jumbo_pending : 0;
tw32_rx_mbox(MAILBOX_RCV_JUMBO_PROD_IDX + TG3_64BIT_REG_LOW,
tp->rx_jumbo_ptr);
udelay(10);
}
- tg3_set_coalesce(tp, &tp->coal);
+ __tg3_set_coalesce(tp, &tp->coal);
/* set status block DMA address */
tw32(HOSTCC_STATUS_BLK_HOST_ADDR + TG3_64BIT_REG_HIGH,
tw32(MAC_RCV_RULE_1, 0x86000004 & RCV_RULE_DISABLE_MASK);
tw32(MAC_RCV_VALUE_1, 0xffffffff & RCV_RULE_DISABLE_MASK);
- if (tp->tg3_flags2 & TG3_FLG2_5705_PLUS)
+ if ((tp->tg3_flags2 & TG3_FLG2_5705_PLUS) &&
+ (GET_ASIC_REV(tp->pci_chip_rev_id) != ASIC_REV_5780))
limit = 8;
else
limit = 16;
udelay(40);
tg3_setup_phy(tp, 0);
}
- }
+ } else if (tp->tg3_flags2 & TG3_FLG2_MII_SERDES)
+ tg3_serdes_parallel_detect(tp);
tp->timer_counter = tp->timer_multiplier;
}
return 0;
}
+static int tg3_set_coalesce(struct net_device *dev, struct ethtool_coalesce *ec)
+{
+ struct tg3 *tp = netdev_priv(dev);
+ u32 max_rxcoal_tick_int = 0, max_txcoal_tick_int = 0;
+ u32 max_stat_coal_ticks = 0, min_stat_coal_ticks = 0;
+
+ if (!(tp->tg3_flags2 & TG3_FLG2_5705_PLUS)) {
+ max_rxcoal_tick_int = MAX_RXCOAL_TICK_INT;
+ max_txcoal_tick_int = MAX_TXCOAL_TICK_INT;
+ max_stat_coal_ticks = MAX_STAT_COAL_TICKS;
+ min_stat_coal_ticks = MIN_STAT_COAL_TICKS;
+ }
+
+ if ((ec->rx_coalesce_usecs > MAX_RXCOL_TICKS) ||
+ (ec->tx_coalesce_usecs > MAX_TXCOL_TICKS) ||
+ (ec->rx_max_coalesced_frames > MAX_RXMAX_FRAMES) ||
+ (ec->tx_max_coalesced_frames > MAX_TXMAX_FRAMES) ||
+ (ec->rx_coalesce_usecs_irq > max_rxcoal_tick_int) ||
+ (ec->tx_coalesce_usecs_irq > max_txcoal_tick_int) ||
+ (ec->rx_max_coalesced_frames_irq > MAX_RXCOAL_MAXF_INT) ||
+ (ec->tx_max_coalesced_frames_irq > MAX_TXCOAL_MAXF_INT) ||
+ (ec->stats_block_coalesce_usecs > max_stat_coal_ticks) ||
+ (ec->stats_block_coalesce_usecs < min_stat_coal_ticks))
+ return -EINVAL;
+
+ /* No rx interrupts will be generated if both are zero */
+ if ((ec->rx_coalesce_usecs == 0) &&
+ (ec->rx_max_coalesced_frames == 0))
+ return -EINVAL;
+
+ /* No tx interrupts will be generated if both are zero */
+ if ((ec->tx_coalesce_usecs == 0) &&
+ (ec->tx_max_coalesced_frames == 0))
+ return -EINVAL;
+
+ /* Only copy relevant parameters, ignore all others. */
+ tp->coal.rx_coalesce_usecs = ec->rx_coalesce_usecs;
+ tp->coal.tx_coalesce_usecs = ec->tx_coalesce_usecs;
+ tp->coal.rx_max_coalesced_frames = ec->rx_max_coalesced_frames;
+ tp->coal.tx_max_coalesced_frames = ec->tx_max_coalesced_frames;
+ tp->coal.rx_coalesce_usecs_irq = ec->rx_coalesce_usecs_irq;
+ tp->coal.tx_coalesce_usecs_irq = ec->tx_coalesce_usecs_irq;
+ tp->coal.rx_max_coalesced_frames_irq = ec->rx_max_coalesced_frames_irq;
+ tp->coal.tx_max_coalesced_frames_irq = ec->tx_max_coalesced_frames_irq;
+ tp->coal.stats_block_coalesce_usecs = ec->stats_block_coalesce_usecs;
+
+ if (netif_running(dev)) {
+ tg3_full_lock(tp, 0);
+ __tg3_set_coalesce(tp, &tp->coal);
+ tg3_full_unlock(tp);
+ }
+ return 0;
+}
+
static struct ethtool_ops tg3_ethtool_ops = {
.get_settings = tg3_get_settings,
.set_settings = tg3_set_settings,
.get_stats_count = tg3_get_stats_count,
.get_ethtool_stats = tg3_get_ethtool_stats,
.get_coalesce = tg3_get_coalesce,
+ .set_coalesce = tg3_set_coalesce,
};
static void __devinit tg3_get_eeprom_size(struct tg3 *tp)
eeprom_phy_id = 0;
tp->phy_id = eeprom_phy_id;
- if (eeprom_phy_serdes)
- tp->tg3_flags2 |= TG3_FLG2_PHY_SERDES;
+ if (eeprom_phy_serdes) {
+ if (GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5780)
+ tp->tg3_flags2 |= TG3_FLG2_MII_SERDES;
+ else
+ tp->tg3_flags2 |= TG3_FLG2_PHY_SERDES;
+ }
if (tp->tg3_flags2 & TG3_FLG2_5750_PLUS)
led_cfg = cfg2 & (NIC_SRAM_DATA_CFG_LED_MODE_MASK |
tp->phy_id = hw_phy_id;
if (hw_phy_id_masked == PHY_ID_BCM8002)
tp->tg3_flags2 |= TG3_FLG2_PHY_SERDES;
+ else
+ tp->tg3_flags2 &= ~TG3_FLG2_PHY_SERDES;
} else {
if (tp->phy_id != PHY_ID_INVALID) {
/* Do nothing, phy ID already set up in
}
}
- if (!(tp->tg3_flags2 & TG3_FLG2_PHY_SERDES) &&
+ if (!(tp->tg3_flags2 & TG3_FLG2_ANY_SERDES) &&
!(tp->tg3_flags & TG3_FLAG_ENABLE_ASF)) {
u32 bmsr, adv_reg, tg3_ctrl;
err = tg3_init_5401phy_dsp(tp);
}
- if (tp->tg3_flags2 & TG3_FLG2_PHY_SERDES)
+ if (tp->tg3_flags2 & TG3_FLG2_ANY_SERDES)
tp->link_config.advertising =
(ADVERTISED_1000baseT_Half |
ADVERTISED_1000baseT_Full |
if (tp->pci_chip_rev_id == CHIPREV_ID_5752_A0_HW)
tp->pci_chip_rev_id = CHIPREV_ID_5752_A0;
+ /* Find msi capability. */
+ if (GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5780)
+ tp->msi_cap = pci_find_capability(tp->pdev, PCI_CAP_ID_MSI);
+
/* Initialize misc host control in PCI block. */
tp->misc_host_ctrl |= (misc_ctrl_reg &
MISC_HOST_CTRL_CHIPREV);
tp->pci_bist = (cacheline_sz_reg >> 24) & 0xff;
if (GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5750 ||
- GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5752)
+ GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5752 ||
+ GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5780)
tp->tg3_flags2 |= TG3_FLG2_5750_PLUS;
if ((GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5705) ||
if (tp->tg3_flags2 & TG3_FLG2_5750_PLUS)
tp->tg3_flags2 |= TG3_FLG2_HW_TSO;
+ if (GET_ASIC_REV(tp->pci_chip_rev_id) != ASIC_REV_5705 &&
+ GET_ASIC_REV(tp->pci_chip_rev_id) != ASIC_REV_5750 &&
+ GET_ASIC_REV(tp->pci_chip_rev_id) != ASIC_REV_5752)
+ tp->tg3_flags2 |= TG3_FLG2_JUMBO_CAPABLE;
+
if (pci_find_capability(tp->pdev, PCI_CAP_ID_EXP) != 0)
tp->tg3_flags2 |= TG3_FLG2_PCI_EXPRESS;
/* Derive initial jumbo mode from MTU assigned in
* ether_setup() via the alloc_etherdev() call
*/
- if (tp->dev->mtu > ETH_DATA_LEN)
- tp->tg3_flags |= TG3_FLAG_JUMBO_ENABLE;
+ if (tp->dev->mtu > ETH_DATA_LEN &&
+ GET_ASIC_REV(tp->pci_chip_rev_id) != ASIC_REV_5780)
+ tp->tg3_flags |= TG3_FLAG_JUMBO_RING_ENABLE;
/* Determine WakeOnLan speed to use. */
if (GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5700 ||
if ((GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5700) ||
((GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5705) &&
(tp->pci_chip_rev_id != CHIPREV_ID_5705_A0) &&
- (tp->pci_chip_rev_id != CHIPREV_ID_5705_A1)))
+ (tp->pci_chip_rev_id != CHIPREV_ID_5705_A1)) ||
+ (tp->tg3_flags2 & TG3_FLG2_ANY_SERDES))
tp->tg3_flags2 |= TG3_FLG2_NO_ETH_WIRE_SPEED;
if (GET_CHIP_REV(tp->pci_chip_rev_id) == CHIPREV_5703_AX ||
#endif
mac_offset = 0x7c;
- if (GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5704 &&
- !(tp->tg3_flags & TG3_FLG2_SUN_570X)) {
+ if ((GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5704 &&
+ !(tp->tg3_flags & TG3_FLG2_SUN_570X)) ||
+ GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5780) {
if (tr32(TG3PCI_DUAL_MAC_CTRL) & DUAL_MAC_CTRL_ID)
mac_offset = 0xcc;
if (tg3_nvram_lock(tp))
/* Set bit 23 to enable PCIX hw bug fix */
tp->dma_rwctrl |= 0x009f0000;
+ } else if (GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5780) {
+ /* 5780 always in PCIX mode */
+ tp->dma_rwctrl |= 0x00144000;
} else {
tp->dma_rwctrl |= 0x001b000f;
}
static void __devinit tg3_init_bufmgr_config(struct tg3 *tp)
{
- tp->bufmgr_config.mbuf_read_dma_low_water =
- DEFAULT_MB_RDMA_LOW_WATER;
- tp->bufmgr_config.mbuf_mac_rx_low_water =
- DEFAULT_MB_MACRX_LOW_WATER;
- tp->bufmgr_config.mbuf_high_water =
- DEFAULT_MB_HIGH_WATER;
+ if (tp->tg3_flags2 & TG3_FLG2_5705_PLUS) {
+ tp->bufmgr_config.mbuf_read_dma_low_water =
+ DEFAULT_MB_RDMA_LOW_WATER_5705;
+ tp->bufmgr_config.mbuf_mac_rx_low_water =
+ DEFAULT_MB_MACRX_LOW_WATER_5705;
+ tp->bufmgr_config.mbuf_high_water =
+ DEFAULT_MB_HIGH_WATER_5705;
+
+ tp->bufmgr_config.mbuf_read_dma_low_water_jumbo =
+ DEFAULT_MB_RDMA_LOW_WATER_JUMBO_5780;
+ tp->bufmgr_config.mbuf_mac_rx_low_water_jumbo =
+ DEFAULT_MB_MACRX_LOW_WATER_JUMBO_5780;
+ tp->bufmgr_config.mbuf_high_water_jumbo =
+ DEFAULT_MB_HIGH_WATER_JUMBO_5780;
+ } else {
+ tp->bufmgr_config.mbuf_read_dma_low_water =
+ DEFAULT_MB_RDMA_LOW_WATER;
+ tp->bufmgr_config.mbuf_mac_rx_low_water =
+ DEFAULT_MB_MACRX_LOW_WATER;
+ tp->bufmgr_config.mbuf_high_water =
+ DEFAULT_MB_HIGH_WATER;
- tp->bufmgr_config.mbuf_read_dma_low_water_jumbo =
- DEFAULT_MB_RDMA_LOW_WATER_JUMBO;
- tp->bufmgr_config.mbuf_mac_rx_low_water_jumbo =
- DEFAULT_MB_MACRX_LOW_WATER_JUMBO;
- tp->bufmgr_config.mbuf_high_water_jumbo =
- DEFAULT_MB_HIGH_WATER_JUMBO;
+ tp->bufmgr_config.mbuf_read_dma_low_water_jumbo =
+ DEFAULT_MB_RDMA_LOW_WATER_JUMBO;
+ tp->bufmgr_config.mbuf_mac_rx_low_water_jumbo =
+ DEFAULT_MB_MACRX_LOW_WATER_JUMBO;
+ tp->bufmgr_config.mbuf_high_water_jumbo =
+ DEFAULT_MB_HIGH_WATER_JUMBO;
+ }
tp->bufmgr_config.dma_low_water = DEFAULT_DMA_LOW_WATER;
tp->bufmgr_config.dma_high_water = DEFAULT_DMA_HIGH_WATER;
case PHY_ID_BCM5705: return "5705";
case PHY_ID_BCM5750: return "5750";
case PHY_ID_BCM5752: return "5752";
+ case PHY_ID_BCM5780: return "5780";
case PHY_ID_BCM8002: return "8002/serdes";
case 0: return "serdes";
default: return "unknown";
ec->tx_coalesce_usecs = LOW_TXCOL_TICKS_CLRTCKS;
ec->tx_coalesce_usecs_irq = DEFAULT_TXCOAL_TICK_INT_CLRTCKS;
}
+
+ if (tp->tg3_flags2 & TG3_FLG2_5705_PLUS) {
+ ec->rx_coalesce_usecs_irq = 0;
+ ec->tx_coalesce_usecs_irq = 0;
+ ec->stats_block_coalesce_usecs = 0;
+ }
}
static int __devinit tg3_init_one(struct pci_dev *pdev,
tg3_init_link_config(tp);
- tg3_init_bufmgr_config(tp);
-
tp->rx_pending = TG3_DEF_RX_RING_PENDING;
tp->rx_jumbo_pending = TG3_DEF_RX_JUMBO_RING_PENDING;
tp->tx_pending = TG3_DEF_TX_RING_PENDING;
goto err_out_iounmap;
}
- if (tp->tg3_flags2 & TG3_FLG2_5705_PLUS) {
- tp->bufmgr_config.mbuf_read_dma_low_water =
- DEFAULT_MB_RDMA_LOW_WATER_5705;
- tp->bufmgr_config.mbuf_mac_rx_low_water =
- DEFAULT_MB_MACRX_LOW_WATER_5705;
- tp->bufmgr_config.mbuf_high_water =
- DEFAULT_MB_HIGH_WATER_5705;
- }
+ tg3_init_bufmgr_config(tp);
#if TG3_TSO_SUPPORT != 0
if (tp->tg3_flags2 & TG3_FLG2_HW_TSO) {
tg3_init_coal(tp);
+ /* Now that we have fully setup the chip, save away a snapshot
+ * of the PCI config space. We need to restore this after
+ * GRC_MISC_CFG core clock resets and some resume events.
+ */
+ pci_save_state(tp->pdev);
+
err = register_netdev(dev);
if (err) {
printk(KERN_ERR PFX "Cannot register net device, "
pci_set_drvdata(pdev, dev);
- /* Now that we have fully setup the chip, save away a snapshot
- * of the PCI config space. We need to restore this after
- * GRC_MISC_CFG core clock resets and some resume events.
- */
- pci_save_state(tp->pdev);
-
printk(KERN_INFO "%s: Tigon3 [partno(%s) rev %04x PHY(%s)] (PCI%s:%s:%s) %sBaseT Ethernet ",
dev->name,
tp->board_part_number,
projects / ~andy / linux / blobdiff