#define EDC_MODE_LINEAR 0x0022
#define EDC_MODE_LIMITING 0x0044
#define EDC_MODE_PASSIVE_DAC 0x0055
+#define EDC_MODE_ACTIVE_DAC 0x0066
/* ETS defines*/
#define DCBX_INVALID_COS (0xFF)
bnx2x_update_link_attr(params, vars->link_attr_sync);
}
+static void bnx2x_disable_kr2(struct link_params *params,
+ struct link_vars *vars,
+ struct bnx2x_phy *phy)
+{
+ struct bnx2x *bp = params->bp;
+ int i;
+ static struct bnx2x_reg_set reg_set[] = {
+ /* Step 1 - Program the TX/RX alignment markers */
+ {MDIO_WC_DEVAD, MDIO_WC_REG_CL82_USERB1_TX_CTRL5, 0x7690},
+ {MDIO_WC_DEVAD, MDIO_WC_REG_CL82_USERB1_TX_CTRL7, 0xe647},
+ {MDIO_WC_DEVAD, MDIO_WC_REG_CL82_USERB1_TX_CTRL6, 0xc4f0},
+ {MDIO_WC_DEVAD, MDIO_WC_REG_CL82_USERB1_TX_CTRL9, 0x7690},
+ {MDIO_WC_DEVAD, MDIO_WC_REG_CL82_USERB1_RX_CTRL11, 0xe647},
+ {MDIO_WC_DEVAD, MDIO_WC_REG_CL82_USERB1_RX_CTRL10, 0xc4f0},
+ {MDIO_WC_DEVAD, MDIO_WC_REG_CL73_USERB0_CTRL, 0x000c},
+ {MDIO_WC_DEVAD, MDIO_WC_REG_CL73_BAM_CTRL1, 0x6000},
+ {MDIO_WC_DEVAD, MDIO_WC_REG_CL73_BAM_CTRL3, 0x0000},
+ {MDIO_WC_DEVAD, MDIO_WC_REG_CL73_BAM_CODE_FIELD, 0x0002},
+ {MDIO_WC_DEVAD, MDIO_WC_REG_ETA_CL73_OUI1, 0x0000},
+ {MDIO_WC_DEVAD, MDIO_WC_REG_ETA_CL73_OUI2, 0x0af7},
+ {MDIO_WC_DEVAD, MDIO_WC_REG_ETA_CL73_OUI3, 0x0af7},
+ {MDIO_WC_DEVAD, MDIO_WC_REG_ETA_CL73_LD_BAM_CODE, 0x0002},
+ {MDIO_WC_DEVAD, MDIO_WC_REG_ETA_CL73_LD_UD_CODE, 0x0000}
+ };
+ DP(NETIF_MSG_LINK, "Disabling 20G-KR2\n");
+
+ for (i = 0; i < ARRAY_SIZE(reg_set); i++)
+ bnx2x_cl45_write(bp, phy, reg_set[i].devad, reg_set[i].reg,
+ reg_set[i].val);
+ vars->link_attr_sync &= ~LINK_ATTR_SYNC_KR2_ENABLE;
+ bnx2x_update_link_attr(params, vars->link_attr_sync);
+
+ vars->check_kr2_recovery_cnt = CHECK_KR2_RECOVERY_CNT;
+}
+
static void bnx2x_warpcore_set_lpi_passthrough(struct bnx2x_phy *phy,
struct link_params *params)
{
struct link_params *params,
struct link_vars *vars) {
u16 lane, i, cl72_ctrl, an_adv = 0;
- u16 ucode_ver;
struct bnx2x *bp = params->bp;
static struct bnx2x_reg_set reg_set[] = {
{MDIO_WC_DEVAD, MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X2, 0x7},
/* Advertise pause */
bnx2x_ext_phy_set_pause(params, phy, vars);
- /* Set KR Autoneg Work-Around flag for Warpcore version older than D108
- */
- bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
- MDIO_WC_REG_UC_INFO_B1_VERSION, &ucode_ver);
- if (ucode_ver < 0xd108) {
- DP(NETIF_MSG_LINK, "Enable AN KR work-around. WC ver:0x%x\n",
- ucode_ver);
- vars->rx_tx_asic_rst = MAX_KR_LINK_RETRY;
- }
+ vars->rx_tx_asic_rst = MAX_KR_LINK_RETRY;
bnx2x_cl45_read_or_write(bp, phy, MDIO_WC_DEVAD,
MDIO_WC_REG_DIGITAL5_MISC7, 0x100);
bnx2x_set_aer_mmd(params, phy);
bnx2x_warpcore_enable_AN_KR2(phy, params, vars);
+ } else {
+ bnx2x_disable_kr2(params, vars, phy);
}
/* Enable Autoneg: only on the main lane */
struct bnx2x *bp = params->bp;
u32 serdes_net_if;
u16 gp_status1 = 0, lnkup = 0, lnkup_kr = 0;
- u16 lane = bnx2x_get_warpcore_lane(phy, params);
vars->turn_to_run_wc_rt = vars->turn_to_run_wc_rt ? 0 : 1;
if (!vars->turn_to_run_wc_rt)
return;
- /* Return if there is no link partner */
- if (!(bnx2x_warpcore_get_sigdet(phy, params))) {
- DP(NETIF_MSG_LINK, "bnx2x_warpcore_get_sigdet false\n");
- return;
- }
-
if (vars->rx_tx_asic_rst) {
+ u16 lane = bnx2x_get_warpcore_lane(phy, params);
serdes_net_if = (REG_RD(bp, params->shmem_base +
offsetof(struct shmem_region, dev_info.
port_hw_config[params->port].default_cfg)) &
/*10G KR*/
lnkup_kr = (gp_status1 >> (12+lane)) & 0x1;
- DP(NETIF_MSG_LINK,
- "gp_status1 0x%x\n", gp_status1);
-
if (lnkup_kr || lnkup) {
- vars->rx_tx_asic_rst = 0;
- DP(NETIF_MSG_LINK,
- "link up, rx_tx_asic_rst 0x%x\n",
- vars->rx_tx_asic_rst);
+ vars->rx_tx_asic_rst = 0;
} else {
/* Reset the lane to see if link comes up.*/
bnx2x_warpcore_reset_lane(bp, phy, 1);
* enabled transmitter to avoid current leakage in case
* no module is connected
*/
- if (bnx2x_is_sfp_module_plugged(phy, params))
- bnx2x_sfp_module_detection(phy, params);
- else
- bnx2x_sfp_e3_set_transmitter(params, phy, 1);
+ if ((params->loopback_mode == LOOPBACK_NONE) ||
+ (params->loopback_mode == LOOPBACK_EXT)) {
+ if (bnx2x_is_sfp_module_plugged(phy, params))
+ bnx2x_sfp_module_detection(phy, params);
+ else
+ bnx2x_sfp_e3_set_transmitter(params,
+ phy, 1);
+ }
bnx2x_warpcore_config_sfi(phy, params);
break;
rc = bnx2x_get_link_speed_duplex(phy, params, vars, link_up, gp_speed,
duplex);
+ /* In case of KR link down, start up the recovering procedure */
+ if ((!link_up) && (phy->media_type == ETH_PHY_KR) &&
+ (!(phy->flags & FLAGS_WC_DUAL_MODE)))
+ vars->rx_tx_asic_rst = MAX_KR_LINK_RETRY;
+
DP(NETIF_MSG_LINK, "duplex %x flow_ctrl 0x%x link_status 0x%x\n",
vars->duplex, vars->flow_ctrl, vars->link_status);
return rc;
params->phy[INT_PHY].config_init(phy, params, vars);
}
+ /* Re-read this value in case it was changed inside config_init due to
+ * limitations of optic module
+ */
+ vars->line_speed = params->phy[INT_PHY].req_line_speed;
+
/* Init external phy*/
if (non_ext_phy) {
if (params->phy[INT_PHY].supported &
if (copper_module_type &
SFP_EEPROM_FC_TX_TECH_BITMASK_COPPER_ACTIVE) {
DP(NETIF_MSG_LINK, "Active Copper cable detected\n");
- check_limiting_mode = 1;
+ if (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT)
+ *edc_mode = EDC_MODE_ACTIVE_DAC;
+ else
+ check_limiting_mode = 1;
} else if (copper_module_type &
SFP_EEPROM_FC_TX_TECH_BITMASK_COPPER_PASSIVE) {
DP(NETIF_MSG_LINK,
mode = MDIO_WC_REG_UC_INFO_B1_FIRMWARE_MODE_DEFAULT;
break;
case EDC_MODE_PASSIVE_DAC:
+ case EDC_MODE_ACTIVE_DAC:
mode = MDIO_WC_REG_UC_INFO_B1_FIRMWARE_MODE_SFP_DAC;
break;
default:
}
}
}
-static void bnx2x_disable_kr2(struct link_params *params,
- struct link_vars *vars,
- struct bnx2x_phy *phy)
-{
- struct bnx2x *bp = params->bp;
- int i;
- static struct bnx2x_reg_set reg_set[] = {
- /* Step 1 - Program the TX/RX alignment markers */
- {MDIO_WC_DEVAD, MDIO_WC_REG_CL82_USERB1_TX_CTRL5, 0x7690},
- {MDIO_WC_DEVAD, MDIO_WC_REG_CL82_USERB1_TX_CTRL7, 0xe647},
- {MDIO_WC_DEVAD, MDIO_WC_REG_CL82_USERB1_TX_CTRL6, 0xc4f0},
- {MDIO_WC_DEVAD, MDIO_WC_REG_CL82_USERB1_TX_CTRL9, 0x7690},
- {MDIO_WC_DEVAD, MDIO_WC_REG_CL82_USERB1_RX_CTRL11, 0xe647},
- {MDIO_WC_DEVAD, MDIO_WC_REG_CL82_USERB1_RX_CTRL10, 0xc4f0},
- {MDIO_WC_DEVAD, MDIO_WC_REG_CL73_USERB0_CTRL, 0x000c},
- {MDIO_WC_DEVAD, MDIO_WC_REG_CL73_BAM_CTRL1, 0x6000},
- {MDIO_WC_DEVAD, MDIO_WC_REG_CL73_BAM_CTRL3, 0x0000},
- {MDIO_WC_DEVAD, MDIO_WC_REG_CL73_BAM_CODE_FIELD, 0x0002},
- {MDIO_WC_DEVAD, MDIO_WC_REG_ETA_CL73_OUI1, 0x0000},
- {MDIO_WC_DEVAD, MDIO_WC_REG_ETA_CL73_OUI2, 0x0af7},
- {MDIO_WC_DEVAD, MDIO_WC_REG_ETA_CL73_OUI3, 0x0af7},
- {MDIO_WC_DEVAD, MDIO_WC_REG_ETA_CL73_LD_BAM_CODE, 0x0002},
- {MDIO_WC_DEVAD, MDIO_WC_REG_ETA_CL73_LD_UD_CODE, 0x0000}
- };
- DP(NETIF_MSG_LINK, "Disabling 20G-KR2\n");
-
- for (i = 0; i < ARRAY_SIZE(reg_set); i++)
- bnx2x_cl45_write(bp, phy, reg_set[i].devad, reg_set[i].reg,
- reg_set[i].val);
- vars->link_attr_sync &= ~LINK_ATTR_SYNC_KR2_ENABLE;
- bnx2x_update_link_attr(params, vars->link_attr_sync);
-
- vars->check_kr2_recovery_cnt = CHECK_KR2_RECOVERY_CNT;
- /* Restart AN on leading lane */
- bnx2x_warpcore_restart_AN_KR(phy, params);
-}
-
static void bnx2x_kr2_recovery(struct link_params *params,
struct link_vars *vars,
struct bnx2x_phy *phy)
/* Disable KR2 on both lanes */
DP(NETIF_MSG_LINK, "BP=0x%x, NP=0x%x\n", base_page, next_page);
bnx2x_disable_kr2(params, vars, phy);
+ /* Restart AN on leading lane */
+ bnx2x_warpcore_restart_AN_KR(phy, params);
return;
}
}
projects / ~andy / linux / blobdiff