If you don't know what to use this for, you don't need it.
config VETH
- tristate "Virtual ethernet device"
+ tristate "Virtual ethernet pair device"
---help---
- The device is an ethernet tunnel. Devices are created in pairs. When
- one end receives the packet it appears on its pair and vice versa.
+ This device is a local ethernet tunnel. Devices are created in pairs.
+ When one end receives the packet it appears on its pair and vice
+ versa.
config NET_SB1000
tristate "General Instruments Surfboard 1000"
If you don't have this card, of course say N.
config IP1000
- tristate "IP1000 Gigabit Ethernet support"
- depends on PCI && EXPERIMENTAL
- ---help---
- This driver supports IP1000 gigabit Ethernet cards.
+ tristate "IP1000 Gigabit Ethernet support"
+ depends on PCI && EXPERIMENTAL
+ select MII
+ ---help---
+ This driver supports IP1000 gigabit Ethernet cards.
- To compile this driver as a module, choose M here: the module
- will be called ipg. This is recommended.
+ To compile this driver as a module, choose M here: the module
+ will be called ipg. This is recommended.
source "drivers/net/arcnet/Kconfig"
config AX88796
tristate "ASIX AX88796 NE2000 clone support"
- depends on ARM || MIPS
+ depends on ARM || MIPS || SUPERH
select CRC32
select MII
help
Say Y here if you want to use the second built-in 10/100 Fast
ethernet controller on some Motorola ColdFire processors.
+config FEC_MPC52xx
+ tristate "MPC52xx FEC driver"
+ depends on PPC_MERGE && PPC_MPC52xx && PPC_BESTCOMM_FEC
+ select CRC32
+ select PHYLIB
+ ---help---
+ This option enables support for the MPC5200's on-chip
+ Fast Ethernet Controller
+ If compiled as module, it will be called 'fec_mpc52xx.ko'.
+
+config FEC_MPC52xx_MDIO
+ bool "MPC52xx FEC MDIO bus driver"
+ depends on FEC_MPC52xx
+ default y
+ ---help---
+ The MPC5200's FEC can connect to the Ethernet either with
+ an external MII PHY chip or 10 Mbps 7-wire interface
+ (Motorola? industry standard).
+ If your board uses an external PHY connected to FEC, enable this.
+ If not sure, enable.
+ If compiled as module, it will be called 'fec_mpc52xx_phy.ko'.
+
config NE_H8300
tristate "NE2000 compatible support for H8/300"
depends on H8300
depends on UCC_GETH
config MV643XX_ETH
- tristate "MV-643XX Ethernet support"
- depends on MV64360 || MV64X60 || (PPC_MULTIPLATFORM && PPC32)
+ tristate "Marvell Discovery (643XX) and Orion ethernet support"
+ depends on MV64360 || MV64X60 || (PPC_MULTIPLATFORM && PPC32) || ARCH_ORION
select MII
help
- This driver supports the gigabit Ethernet on the Marvell MV643XX
- chipset which is used in the Momenco Ocelot C and Jaguar ATX and
- Pegasos II, amongst other PPC and MIPS boards.
+ This driver supports the gigabit ethernet MACs in the
+ Marvell Discovery PPC/MIPS chipset family (MV643XX) and
+ in the Marvell Orion ARM SoC family.
+
+ Some boards that use the Discovery chipset are the Momenco
+ Ocelot C and Jaguar ATX and Pegasos II.
config QLA3XXX
tristate "QLogic QLA3XXX Network Driver Support"
config NET_POLL_CONTROLLER
def_bool NETPOLL
+config VIRTIO_NET
+ tristate "Virtio network driver (EXPERIMENTAL)"
+ depends on EXPERIMENTAL && VIRTIO
+ ---help---
+ This is the virtual network driver for lguest. Say Y or M.
+
endif # NETDEVICES