If unsure, say Y.
+# All the following symbols are dependent on NETDEVICES - do not repeat
+# that for each of the symbols.
+if NETDEVICES
+
config DUMMY
tristate "Dummy net driver support"
- depends on NETDEVICES
---help---
This is essentially a bit-bucket device (i.e. traffic you send to
this device is consigned into oblivion) with a configurable IP
config BONDING
tristate "Bonding driver support"
- depends on NETDEVICES
depends on INET
---help---
Say 'Y' or 'M' if you wish to be able to 'bond' multiple Ethernet
config EQUALIZER
tristate "EQL (serial line load balancing) support"
- depends on NETDEVICES
---help---
If you have two serial connections to some other computer (this
usually requires two modems and two telephone lines) and you use
config TUN
tristate "Universal TUN/TAP device driver support"
- depends on NETDEVICES
select CRC32
---help---
TUN/TAP provides packet reception and transmission for user space
config NET_SB1000
tristate "General Instruments Surfboard 1000"
- depends on NETDEVICES && PNP
+ depends on PNP
---help---
This is a driver for the General Instrument (also known as
NextLevel) SURFboard 1000 internal
If you don't have this card, of course say N.
-if NETDEVICES
source "drivers/net/arcnet/Kconfig"
-endif
+
+source "drivers/net/phy/Kconfig"
#
# Ethernet
#
menu "Ethernet (10 or 100Mbit)"
- depends on NETDEVICES && !UML
+ depends on !UML
config NET_ETHERNET
bool "Ethernet (10 or 100Mbit)"
If you're not building a kernel for a Sun 3, say N.
config SUN3_82586
- tristate "Sun3 on-board Intel 82586 support"
+ bool "Sun3 on-board Intel 82586 support"
depends on NET_ETHERNET && SUN3
help
This driver enables support for the on-board Intel 82586 based
config SGI_IOC3_ETH
bool "SGI IOC3 Ethernet"
- depends on NET_ETHERNET && PCI && SGI_IP27
+ depends on NET_ETHERNET && PCI && SGI_IP27 && BROKEN
select CRC32
select MII
help
config IBMVETH
tristate "IBM LAN Virtual Ethernet support"
- depends on NETDEVICES && NET_ETHERNET && PPC_PSERIES
+ depends on NET_ETHERNET && PPC_PSERIES
---help---
This driver supports virtual ethernet adapters on newer IBM iSeries
and pSeries systems.
be called ibmveth.
config IBM_EMAC
- tristate "IBM PPC4xx EMAC driver support"
+ bool "IBM PPC4xx EMAC driver support"
depends on 4xx
select CRC32
---help---
config IBM_EMAC_ERRMSG
bool "Verbose error messages"
- depends on IBM_EMAC
+ depends on IBM_EMAC && BROKEN
config IBM_EMAC_RXB
int "Number of receive buffers"
#
menu "Ethernet (1000 Mbit)"
- depends on NETDEVICES && !UML
+ depends on !UML
config ACENIC
tristate "Alteon AceNIC/3Com 3C985/NetGear GA620 Gigabit support"
If in doubt, say Y.
+config SIS190
+ tristate "SiS190/SiS191 gigabit ethernet support"
+ depends on PCI
+ select CRC32
+ select MII
+ ---help---
+ Say Y here if you have a SiS 190 PCI Fast Ethernet adapter or
+ a SiS 191 PCI Gigabit Ethernet adapter. Both are expected to
+ appear in lan on motherboard designs which are based on SiS 965
+ and SiS 966 south bridge.
+
+ To compile this driver as a module, choose M here: the module
+ will be called sis190. This is recommended.
+
config SKGE
tristate "New SysKonnect GigaEthernet support (EXPERIMENTAL)"
depends on PCI && EXPERIMENTAL
#
menu "Ethernet (10000 Mbit)"
- depends on NETDEVICES && !UML
+ depends on !UML
+
+config CHELSIO_T1
+ tristate "Chelsio 10Gb Ethernet support"
+ depends on PCI
+ help
+ This driver supports Chelsio N110 and N210 models 10Gb Ethernet
+ cards. More information about adapter features and performance
+ tuning is in <file:Documentation/networking/cxgb.txt>.
+
+ For general information about Chelsio and our products, visit
+ our website at <http://www.chelsio.com>.
+
+ For customer support, please visit our customer support page at
+ <http://www.chelsio.com/support.htm>.
+
+ Please send feedback to <linux-bugs@chelsio.com>.
+
+ To compile this driver as a module, choose M here: the module
+ will be called cxgb.
config IXGB
tristate "Intel(R) PRO/10GbE support"
config ISERIES_VETH
tristate "iSeries Virtual Ethernet driver support"
- depends on NETDEVICES && PPC_ISERIES
+ depends on PPC_ISERIES
config FDDI
bool "FDDI driver support"
- depends on NETDEVICES && (PCI || EISA)
+ depends on (PCI || EISA)
help
Fiber Distributed Data Interface is a high speed local area network
design; essentially a replacement for high speed Ethernet. FDDI can
config HIPPI
bool "HIPPI driver support (EXPERIMENTAL)"
- depends on NETDEVICES && EXPERIMENTAL && INET && PCI
+ depends on EXPERIMENTAL && INET && PCI
help
HIgh Performance Parallel Interface (HIPPI) is a 800Mbit/sec and
1600Mbit/sec dual-simplex switched or point-to-point network. HIPPI
config PLIP
tristate "PLIP (parallel port) support"
- depends on NETDEVICES && PARPORT
+ depends on PARPORT
---help---
PLIP (Parallel Line Internet Protocol) is used to create a
reasonably fast mini network consisting of two (or, rarely, more)
config PPP
tristate "PPP (point-to-point protocol) support"
- depends on NETDEVICES
---help---
PPP (Point to Point Protocol) is a newer and better SLIP. It serves
the same purpose: sending Internet traffic over telephone (and other
config SLIP
tristate "SLIP (serial line) support"
- depends on NETDEVICES
---help---
Say Y if you intend to use SLIP or CSLIP (compressed SLIP) to
connect to your Internet service provider or to connect to some
config NET_FC
bool "Fibre Channel driver support"
- depends on NETDEVICES && SCSI && PCI
+ depends on SCSI && PCI
help
Fibre Channel is a high speed serial protocol mainly used to connect
large storage devices to the computer; it is compatible with and
config SHAPER
tristate "Traffic Shaper (EXPERIMENTAL)"
- depends on NETDEVICES && EXPERIMENTAL
+ depends on EXPERIMENTAL
---help---
The traffic shaper is a virtual network device that allows you to
limit the rate of outgoing data flow over some other network device.
config NETCONSOLE
tristate "Network console logging support (EXPERIMENTAL)"
- depends on NETDEVICES && EXPERIMENTAL
+ depends on EXPERIMENTAL
---help---
If you want to log kernel messages over the network, enable this.
See <file:Documentation/networking/netconsole.txt> for details.
+endif #NETDEVICES
+
+config NETPOLL
+ def_bool NETCONSOLE
+
+config NETPOLL_RX
+ bool "Netpoll support for trapping incoming packets"
+ default n
+ depends on NETPOLL
+
+config NETPOLL_TRAP
+ bool "Netpoll traffic trapping"
+ default n
+ depends on NETPOLL
+
+config NET_POLL_CONTROLLER
+ def_bool NETPOLL
+
endmenu
projects / ~andy / linux / blobdiff