*/
int db8500_prcmu_request_clock(u8 clock, bool enable)
{
- if (clock == PRCMU_SGACLK)
+ switch(clock) {
+ case PRCMU_SGACLK:
return request_sga_clock(clock, enable);
- else if (clock < PRCMU_NUM_REG_CLOCKS)
- return request_reg_clock(clock, enable);
- else if (clock == PRCMU_TIMCLK)
+ case PRCMU_TIMCLK:
return request_timclk(enable);
- else if (clock == PRCMU_SYSCLK)
+ case PRCMU_SYSCLK:
return request_sysclk(enable);
- else if (clock == PRCMU_PLLSOC1)
+ case PRCMU_PLLSOC1:
return request_pll(clock, enable);
- else
- return -EINVAL;
+ default:
+ break;
+ }
+ if (clock < PRCMU_NUM_REG_CLOCKS)
+ return request_reg_clock(clock, enable);
+ return -EINVAL;
}
int db8500_prcmu_config_esram0_deep_sleep(u8 state)
return config_hot_period(0xFFFF);
}
+static int prcmu_a9wdog(u8 cmd, u8 d0, u8 d1, u8 d2, u8 d3)
+{
+
+ mutex_lock(&mb4_transfer.lock);
+
+ while (readl(PRCM_MBOX_CPU_VAL) & MBOX_BIT(4))
+ cpu_relax();
+
+ writeb(d0, (tcdm_base + PRCM_REQ_MB4_A9WDOG_0));
+ writeb(d1, (tcdm_base + PRCM_REQ_MB4_A9WDOG_1));
+ writeb(d2, (tcdm_base + PRCM_REQ_MB4_A9WDOG_2));
+ writeb(d3, (tcdm_base + PRCM_REQ_MB4_A9WDOG_3));
+
+ writeb(cmd, (tcdm_base + PRCM_MBOX_HEADER_REQ_MB4));
+
+ writel(MBOX_BIT(4), PRCM_MBOX_CPU_SET);
+ wait_for_completion(&mb4_transfer.work);
+
+ mutex_unlock(&mb4_transfer.lock);
+
+ return 0;
+
+}
+
+int prcmu_config_a9wdog(u8 num, bool sleep_auto_off)
+{
+ BUG_ON(num == 0 || num > 0xf);
+ return prcmu_a9wdog(MB4H_A9WDOG_CONF, num, 0, 0,
+ sleep_auto_off ? A9WDOG_AUTO_OFF_EN :
+ A9WDOG_AUTO_OFF_DIS);
+}
+
+int prcmu_enable_a9wdog(u8 id)
+{
+ return prcmu_a9wdog(MB4H_A9WDOG_EN, id, 0, 0, 0);
+}
+
+int prcmu_disable_a9wdog(u8 id)
+{
+ return prcmu_a9wdog(MB4H_A9WDOG_DIS, id, 0, 0, 0);
+}
+
+int prcmu_kick_a9wdog(u8 id)
+{
+ return prcmu_a9wdog(MB4H_A9WDOG_KICK, id, 0, 0, 0);
+}
+
+/*
+ * timeout is 28 bit, in ms.
+ */
+#define MAX_WATCHDOG_TIMEOUT 131000
+int prcmu_load_a9wdog(u8 id, u32 timeout)
+{
+ if (timeout > MAX_WATCHDOG_TIMEOUT)
+ /*
+ * Due to calculation bug in prcmu fw, timeouts
+ * can't be bigger than 131 seconds.
+ */
+ return -EINVAL;
+
+ return prcmu_a9wdog(MB4H_A9WDOG_LOAD,
+ (id & A9WDOG_ID_MASK) |
+ /*
+ * Put the lowest 28 bits of timeout at
+ * offset 4. Four first bits are used for id.
+ */
+ (u8)((timeout << 4) & 0xf0),
+ (u8)((timeout >> 4) & 0xff),
+ (u8)((timeout >> 12) & 0xff),
+ (u8)((timeout >> 20) & 0xff));
+}
+
/**
* prcmu_set_clock_divider() - Configure the clock divider.
* @clock: The clock for which the request is made.
void prcmu_ac_wake_req(void)
{
u32 val;
+ u32 status;
mutex_lock(&mb0_transfer.ac_wake_lock);
atomic_set(&ac_wake_req_state, 1);
+retry:
writel((val | PRCM_HOSTACCESS_REQ_HOSTACCESS_REQ), PRCM_HOSTACCESS_REQ);
if (!wait_for_completion_timeout(&mb0_transfer.ac_wake_work,
- msecs_to_jiffies(20000))) {
- pr_err("prcmu: %s timed out (20 s) waiting for a reply.\n",
+ msecs_to_jiffies(5000))) {
+ pr_crit("prcmu: %s timed out (5 s) waiting for a reply.\n",
+ __func__);
+ goto unlock_and_return;
+ }
+
+ /*
+ * The modem can generate an AC_WAKE_ACK, and then still go to sleep.
+ * As a workaround, we wait, and then check that the modem is indeed
+ * awake (in terms of the value of the PRCM_MOD_AWAKE_STATUS
+ * register, which may not be the whole truth).
+ */
+ udelay(400);
+ status = (readl(PRCM_MOD_AWAKE_STATUS) & BITS(0, 2));
+ if (status != (PRCM_MOD_AWAKE_STATUS_PRCM_MOD_AAPD_AWAKE |
+ PRCM_MOD_AWAKE_STATUS_PRCM_MOD_COREPD_AWAKE)) {
+ pr_err("prcmu: %s received ack, but modem not awake (0x%X).\n",
+ __func__, status);
+ udelay(1200);
+ writel(val, PRCM_HOSTACCESS_REQ);
+ if (wait_for_completion_timeout(&mb0_transfer.ac_wake_work,
+ msecs_to_jiffies(5000)))
+ goto retry;
+ pr_crit("prcmu: %s timed out (5 s) waiting for AC_SLEEP_ACK.\n",
__func__);
}
PRCM_HOSTACCESS_REQ);
if (!wait_for_completion_timeout(&mb0_transfer.ac_wake_work,
- msecs_to_jiffies(20000))) {
- pr_err("prcmu: %s timed out (20 s) waiting for a reply.\n",
+ msecs_to_jiffies(5000))) {
+ pr_crit("prcmu: %s timed out (5 s) waiting for a reply.\n",
__func__);
}
writel(1, PRCM_APE_SOFTRST);
}
+/**
+ * db8500_prcmu_get_reset_code - Retrieve SW reset reason code
+ *
+ * Retrieves the reset reason code stored by prcmu_system_reset() before
+ * last restart.
+ */
+u16 db8500_prcmu_get_reset_code(void)
+{
+ return readw(tcdm_base + PRCM_SW_RST_REASON);
+}
+
/**
* prcmu_reset_modem - ask the PRCMU to reset modem
*/
}
}
-static void __init init_prcm_registers(void)
+static void __init db8500_prcmu_init_clkforce(void)
{
u32 val;
static struct regulator_consumer_supply db8500_b2r2_mcde_consumers[] = {
REGULATOR_SUPPLY("vsupply", "b2r2.0"),
- REGULATOR_SUPPLY("vsupply", "mcde.0"),
+ REGULATOR_SUPPLY("vsupply", "mcde"),
+};
+
+/* SVA MMDSP regulator switch */
+static struct regulator_consumer_supply db8500_svammdsp_consumers[] = {
+ REGULATOR_SUPPLY("sva-mmdsp", "cm_control"),
+};
+
+/* SVA pipe regulator switch */
+static struct regulator_consumer_supply db8500_svapipe_consumers[] = {
+ REGULATOR_SUPPLY("sva-pipe", "cm_control"),
+};
+
+/* SIA MMDSP regulator switch */
+static struct regulator_consumer_supply db8500_siammdsp_consumers[] = {
+ REGULATOR_SUPPLY("sia-mmdsp", "cm_control"),
+};
+
+/* SIA pipe regulator switch */
+static struct regulator_consumer_supply db8500_siapipe_consumers[] = {
+ REGULATOR_SUPPLY("sia-pipe", "cm_control"),
+};
+
+static struct regulator_consumer_supply db8500_sga_consumers[] = {
+ REGULATOR_SUPPLY("v-mali", NULL),
+};
+
+/* ESRAM1 and 2 regulator switch */
+static struct regulator_consumer_supply db8500_esram12_consumers[] = {
+ REGULATOR_SUPPLY("esram12", "cm_control"),
+};
+
+/* ESRAM3 and 4 regulator switch */
+static struct regulator_consumer_supply db8500_esram34_consumers[] = {
+ REGULATOR_SUPPLY("v-esram34", "mcde"),
+ REGULATOR_SUPPLY("esram34", "cm_control"),
};
static struct regulator_init_data db8500_regulators[DB8500_NUM_REGULATORS] = {
.name = "db8500-sva-mmdsp",
.valid_ops_mask = REGULATOR_CHANGE_STATUS,
},
+ .consumer_supplies = db8500_svammdsp_consumers,
+ .num_consumer_supplies = ARRAY_SIZE(db8500_svammdsp_consumers),
},
[DB8500_REGULATOR_SWITCH_SVAMMDSPRET] = {
.constraints = {
.name = "db8500-sva-pipe",
.valid_ops_mask = REGULATOR_CHANGE_STATUS,
},
+ .consumer_supplies = db8500_svapipe_consumers,
+ .num_consumer_supplies = ARRAY_SIZE(db8500_svapipe_consumers),
},
[DB8500_REGULATOR_SWITCH_SIAMMDSP] = {
.supply_regulator = "db8500-vape",
.name = "db8500-sia-mmdsp",
.valid_ops_mask = REGULATOR_CHANGE_STATUS,
},
+ .consumer_supplies = db8500_siammdsp_consumers,
+ .num_consumer_supplies = ARRAY_SIZE(db8500_siammdsp_consumers),
},
[DB8500_REGULATOR_SWITCH_SIAMMDSPRET] = {
.constraints = {
.name = "db8500-sia-pipe",
.valid_ops_mask = REGULATOR_CHANGE_STATUS,
},
+ .consumer_supplies = db8500_siapipe_consumers,
+ .num_consumer_supplies = ARRAY_SIZE(db8500_siapipe_consumers),
},
[DB8500_REGULATOR_SWITCH_SGA] = {
.supply_regulator = "db8500-vape",
.name = "db8500-sga",
.valid_ops_mask = REGULATOR_CHANGE_STATUS,
},
+ .consumer_supplies = db8500_sga_consumers,
+ .num_consumer_supplies = ARRAY_SIZE(db8500_sga_consumers),
+
},
[DB8500_REGULATOR_SWITCH_B2R2_MCDE] = {
.supply_regulator = "db8500-vape",
.name = "db8500-esram12",
.valid_ops_mask = REGULATOR_CHANGE_STATUS,
},
+ .consumer_supplies = db8500_esram12_consumers,
+ .num_consumer_supplies = ARRAY_SIZE(db8500_esram12_consumers),
},
[DB8500_REGULATOR_SWITCH_ESRAM12RET] = {
.constraints = {
.name = "db8500-esram34",
.valid_ops_mask = REGULATOR_CHANGE_STATUS,
},
+ .consumer_supplies = db8500_esram34_consumers,
+ .num_consumer_supplies = ARRAY_SIZE(db8500_esram34_consumers),
},
[DB8500_REGULATOR_SWITCH_ESRAM34RET] = {
.constraints = {
if (ux500_is_svp())
return -ENODEV;
- init_prcm_registers();
+ db8500_prcmu_init_clkforce();
/* Clean up the mailbox interrupts after pre-kernel code. */
writel(ALL_MBOX_BITS, PRCM_ARM_IT1_CLR);
projects / ~andy / linux / blobdiff