# Andre Hedrick <andre@linux-ide.org>
#
+# Select HAVE_IDE if IDE is supported
+config HAVE_IDE
+ def_bool n
+
menuconfig IDE
tristate "ATA/ATAPI/MFM/RLL support"
+ depends on HAVE_IDE
depends on BLOCK
- depends on HAS_IOMEM
---help---
If you say Y here, your kernel will be able to manage low cost mass
storage units such as ATA/(E)IDE and ATAPI units. The most common
To compile this driver as a module, choose M here: the
module will be called ide.
- For further information, please read <file:Documentation/ide.txt>.
+ For further information, please read <file:Documentation/ide/ide.txt>.
If unsure, say Y.
Useful information about large (>540 MB) IDE disks, multiple
interfaces, what to do if ATA/IDE devices are not automatically
detected, sound card ATA/IDE ports, module support, and other
- topics, is contained in <file:Documentation/ide.txt>. For detailed
+ topics, is contained in <file:Documentation/ide/ide.txt>. For detailed
information about hard drives, consult the Disk-HOWTO and the
Multi-Disk-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
<ftp://ibiblio.org/pub/Linux/system/hardware/>.
To compile this driver as a module, choose M here and read
- <file:Documentation/ide.txt>. The module will be called ide-mod.
+ <file:Documentation/ide/ide.txt>. The module will be called ide-mod.
Do not compile this driver as a module if your root file system (the
one containing the directory /) is located on an IDE device.
if BLK_DEV_IDE
-comment "Please see Documentation/ide.txt for help/info on IDE drives"
+comment "Please see Documentation/ide/ide.txt for help/info on IDE drives"
config BLK_DEV_IDE_SATA
bool "Support for SATA (deprecated; conflicts with libata SATA driver)"
along with other IDE devices, as "hdb" or "hdc", or something
similar, and will be mapped to a character device such as "ht0"
(check the boot messages with dmesg). Be sure to consult the
- <file:drivers/ide/ide-tape.c> and <file:Documentation/ide.txt> files
- for usage information.
+ <file:drivers/ide/ide-tape.c> and <file:Documentation/ide/ide.txt>
+ files for usage information.
To compile this driver as a module, choose M here: the
module will be called ide-tape.
The CMD640 chip is also used on add-in cards by Acculogic, and on
the "CSA-6400E PCI to IDE controller" that some people have. For
- details, read <file:Documentation/ide.txt>.
+ details, read <file:Documentation/ide/ide.txt>.
config BLK_DEV_CMD640_ENHANCED
bool "CMD640 enhanced support"
help
This option includes support for setting/autotuning PIO modes and
prefetch on CMD640 IDE interfaces. For details, read
- <file:Documentation/ide.txt>. If you have a CMD640 IDE interface
+ <file:Documentation/ide/ide.txt>. If you have a CMD640 IDE interface
and your BIOS does not already do this for you, then say Y here.
Otherwise say N.
would like the kernel to automatically detect and activate
it, say Y here.
+config BLK_DEV_IDEDMA_SFF
+ bool
+
if PCI
comment "PCI IDE chipsets support"
config BLK_DEV_IDEDMA_PCI
bool
select BLK_DEV_IDEPCI
+ select BLK_DEV_IDEDMA_SFF
config BLK_DEV_AEC62XX
tristate "AEC62XX chipset support"
If unsure, say N.
-config PDC202XX_BURST
- bool "Special UDMA Feature"
- depends on BLK_DEV_PDC202XX_OLD
- help
- This option causes the pdc202xx driver to enable UDMA modes on the
- PDC202xx even when the PDC202xx BIOS has not done so.
-
- It was originally designed for the PDC20246/Ultra33, whose BIOS will
- only setup UDMA on the first two PDC20246 cards. It has also been
- used successfully on a PDC20265/Ultra100, allowing use of UDMA modes
- when the PDC20265 BIOS has been disabled (for faster boot up).
-
- Please read the comments at the top of
- <file:drivers/ide/pci/pdc202xx_old.c>.
-
- If unsure, say N.
-
config BLK_DEV_PDC202XX_NEW
tristate "PROMISE PDC202{68|69|70|71|75|76|77} support"
select BLK_DEV_IDEDMA_PCI
config BLK_DEV_PALMCHIP_BK3710
tristate "Palmchip bk3710 IDE controller support"
depends on ARCH_DAVINCI
- select BLK_DEV_IDEDMA_PCI
+ select BLK_DEV_IDEDMA_SFF
help
Say Y here if you want to support the onchip IDE controller on the
TI DaVinci SoC
This driver is enabled at runtime using the "ali14xx.probe" kernel
boot parameter. It enables support for the secondary IDE interface
of the ALI M1439/1443/1445/1487/1489 chipsets, and permits faster
- I/O speeds to be set as well. See the files
- <file:Documentation/ide.txt> and <file:drivers/ide/legacy/ali14xx.c>
- for more info.
+ I/O speeds to be set as well.
+ See the files <file:Documentation/ide/ide.txt> and
+ <file:drivers/ide/legacy/ali14xx.c> for more info.
config BLK_DEV_DTC2278
tristate "DTC-2278 support"
This driver is enabled at runtime using the "dtc2278.probe" kernel
boot parameter. It enables support for the secondary IDE interface
of the DTC-2278 card, and permits faster I/O speeds to be set as
- well. See the <file:Documentation/ide.txt> and
+ well. See the <file:Documentation/ide/ide.txt> and
<file:drivers/ide/legacy/dtc2278.c> files for more info.
config BLK_DEV_HT6560B
This driver is enabled at runtime using the "ht6560b.probe" kernel
boot parameter. It enables support for the secondary IDE interface
of the Holtek card, and permits faster I/O speeds to be set as well.
- See the <file:Documentation/ide.txt> and
+ See the <file:Documentation/ide/ide.txt> and
<file:drivers/ide/legacy/ht6560b.c> files for more info.
config BLK_DEV_QD65XX
help
This driver is enabled at runtime using the "qd65xx.probe" kernel
boot parameter. It permits faster I/O speeds to be set. See the
- <file:Documentation/ide.txt> and <file:drivers/ide/legacy/qd65xx.c>
+ <file:Documentation/ide/ide.txt> and <file:drivers/ide/legacy/qd65xx.c>
for more info.
config BLK_DEV_UMC8672
This driver is enabled at runtime using the "umc8672.probe" kernel
boot parameter. It enables support for the secondary IDE interface
of the UMC-8672, and permits faster I/O speeds to be set as well.
- See the files <file:Documentation/ide.txt> and
+ See the files <file:Documentation/ide/ide.txt> and
<file:drivers/ide/legacy/umc8672.c> for more info.
endif
config BLK_DEV_IDEDMA
- def_bool BLK_DEV_IDEDMA_PCI || BLK_DEV_IDEDMA_PMAC || BLK_DEV_IDEDMA_ICS || BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA
+ def_bool BLK_DEV_IDEDMA_SFF || BLK_DEV_IDEDMA_PMAC || \
+ BLK_DEV_IDEDMA_ICS || BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA
config IDE_ARCH_OBSOLETE_INIT
def_bool ALPHA || (ARM && !ARCH_L7200) || BLACKFIN || X86 || IA64 || M32R || MIPS || PARISC || PPC || (SUPERH64 && BLK_DEV_IDEPCI) || SPARC
projects / ~andy / linux / blobdiff