#include <linux/interrupt.h>
#include <linux/delay.h>
#include <linux/export.h>
+#include <linux/gpio.h>
+#include <linux/of_gpio.h>
+
#include "ahci.h"
#define CPHY_MAP(dev, addr) ((((dev) & 0x1f) << 7) | (((addr) >> 9) & 0x7f))
};
static struct phy_lane_info port_data[CPHY_PORT_COUNT];
+static DEFINE_SPINLOCK(sgpio_lock);
+#define SCLOCK 0
+#define SLOAD 1
+#define SDATA 2
+#define SGPIO_PINS 3
+#define SGPIO_PORTS 8
+
+/* can be cast as an ahci_host_priv for compatibility with most functions */
+struct ecx_plat_data {
+ u32 n_ports;
+ unsigned sgpio_gpio[SGPIO_PINS];
+ u32 sgpio_pattern;
+ u32 port_to_sgpio[SGPIO_PORTS];
+};
+
+#define SGPIO_SIGNALS 3
+#define ECX_ACTIVITY_BITS 0x300000
+#define ECX_ACTIVITY_SHIFT 2
+#define ECX_LOCATE_BITS 0x80000
+#define ECX_LOCATE_SHIFT 1
+#define ECX_FAULT_BITS 0x400000
+#define ECX_FAULT_SHIFT 0
+static inline int sgpio_bit_shift(struct ecx_plat_data *pdata, u32 port,
+ u32 shift)
+{
+ return 1 << (3 * pdata->port_to_sgpio[port] + shift);
+}
+
+static void ecx_parse_sgpio(struct ecx_plat_data *pdata, u32 port, u32 state)
+{
+ if (state & ECX_ACTIVITY_BITS)
+ pdata->sgpio_pattern |= sgpio_bit_shift(pdata, port,
+ ECX_ACTIVITY_SHIFT);
+ else
+ pdata->sgpio_pattern &= ~sgpio_bit_shift(pdata, port,
+ ECX_ACTIVITY_SHIFT);
+ if (state & ECX_LOCATE_BITS)
+ pdata->sgpio_pattern |= sgpio_bit_shift(pdata, port,
+ ECX_LOCATE_SHIFT);
+ else
+ pdata->sgpio_pattern &= ~sgpio_bit_shift(pdata, port,
+ ECX_LOCATE_SHIFT);
+ if (state & ECX_FAULT_BITS)
+ pdata->sgpio_pattern |= sgpio_bit_shift(pdata, port,
+ ECX_FAULT_SHIFT);
+ else
+ pdata->sgpio_pattern &= ~sgpio_bit_shift(pdata, port,
+ ECX_FAULT_SHIFT);
+}
+
+/*
+ * Tell the LED controller that the signal has changed by raising the clock
+ * line for 50 uS and then lowering it for 50 uS.
+ */
+static void ecx_led_cycle_clock(struct ecx_plat_data *pdata)
+{
+ gpio_set_value(pdata->sgpio_gpio[SCLOCK], 1);
+ udelay(50);
+ gpio_set_value(pdata->sgpio_gpio[SCLOCK], 0);
+ udelay(50);
+}
+
+static ssize_t ecx_transmit_led_message(struct ata_port *ap, u32 state,
+ ssize_t size)
+{
+ struct ahci_host_priv *hpriv = ap->host->private_data;
+ struct ecx_plat_data *pdata = (struct ecx_plat_data *) hpriv->plat_data;
+ struct ahci_port_priv *pp = ap->private_data;
+ unsigned long flags;
+ int pmp, i;
+ struct ahci_em_priv *emp;
+ u32 sgpio_out;
+
+ /* get the slot number from the message */
+ pmp = (state & EM_MSG_LED_PMP_SLOT) >> 8;
+ if (pmp < EM_MAX_SLOTS)
+ emp = &pp->em_priv[pmp];
+ else
+ return -EINVAL;
+
+ if (!(hpriv->em_msg_type & EM_MSG_TYPE_LED))
+ return size;
+
+ spin_lock_irqsave(&sgpio_lock, flags);
+ ecx_parse_sgpio(pdata, ap->port_no, state);
+ sgpio_out = pdata->sgpio_pattern;
+ gpio_set_value(pdata->sgpio_gpio[SLOAD], 1);
+ ecx_led_cycle_clock(pdata);
+ gpio_set_value(pdata->sgpio_gpio[SLOAD], 0);
+ /*
+ * bit-bang out the SGPIO pattern, by consuming a bit and then
+ * clocking it out.
+ */
+ for (i = 0; i < (SGPIO_SIGNALS * pdata->n_ports); i++) {
+ gpio_set_value(pdata->sgpio_gpio[SDATA], sgpio_out & 1);
+ sgpio_out >>= 1;
+ ecx_led_cycle_clock(pdata);
+ }
+
+ /* save off new led state for port/slot */
+ emp->led_state = state;
+
+ spin_unlock_irqrestore(&sgpio_lock, flags);
+ return size;
+}
+
+static void highbank_set_em_messages(struct device *dev,
+ struct ahci_host_priv *hpriv,
+ struct ata_port_info *pi)
+{
+ struct device_node *np = dev->of_node;
+ struct ecx_plat_data *pdata = hpriv->plat_data;
+ int i;
+ int err;
+
+ for (i = 0; i < SGPIO_PINS; i++) {
+ err = of_get_named_gpio(np, "calxeda,sgpio-gpio", i);
+ if (IS_ERR_VALUE(err))
+ return;
+
+ pdata->sgpio_gpio[i] = err;
+ err = gpio_request(pdata->sgpio_gpio[i], "CX SGPIO");
+ if (err) {
+ pr_err("sata_highbank gpio_request %d failed: %d\n",
+ i, err);
+ return;
+ }
+ gpio_direction_output(pdata->sgpio_gpio[i], 1);
+ }
+ of_property_read_u32_array(np, "calxeda,led-order",
+ pdata->port_to_sgpio,
+ pdata->n_ports);
+
+ /* store em_loc */
+ hpriv->em_loc = 0;
+ hpriv->em_buf_sz = 4;
+ hpriv->em_msg_type = EM_MSG_TYPE_LED;
+ pi->flags |= ATA_FLAG_EM | ATA_FLAG_SW_ACTIVITY;
+}
+
static u32 __combo_phy_reg_read(u8 sata_port, u32 addr)
{
u32 data;
return 0;
}
+/*
+ * The Calxeda SATA phy intermittently fails to bring up a link with Gen3
+ * Retrying the phy hard reset can work around the issue, but the drive
+ * may fail again. In less than 150 out of 15000 test runs, it took more
+ * than 10 tries for the link to be established (but never more than 35).
+ * Triple the maximum observed retry count to provide plenty of margin for
+ * rare events and to guarantee that the link is established.
+ *
+ * Also, the default 2 second time-out on a failed drive is too long in
+ * this situation. The uboot implementation of the same driver function
+ * uses a much shorter time-out period and never experiences a time out
+ * issue. Reducing the time-out to 500ms improves the responsiveness.
+ * The other timing constants were kept the same as the stock AHCI driver.
+ * This change was also tested 15000 times on 24 drives and none of them
+ * experienced a time out.
+ */
static int ahci_highbank_hardreset(struct ata_link *link, unsigned int *class,
unsigned long deadline)
{
- const unsigned long *timing = sata_ehc_deb_timing(&link->eh_context);
+ static const unsigned long timing[] = { 5, 100, 500};
struct ata_port *ap = link->ap;
struct ahci_port_priv *pp = ap->private_data;
u8 *d2h_fis = pp->rx_fis + RX_FIS_D2H_REG;
bool online;
u32 sstatus;
int rc;
- int retry = 10;
+ int retry = 100;
ahci_stop_engine(ap);
static struct ata_port_operations ahci_highbank_ops = {
.inherits = &ahci_ops,
.hardreset = ahci_highbank_hardreset,
+ .transmit_led_message = ecx_transmit_led_message,
};
static const struct ata_port_info ahci_highbank_port_info = {
{
struct device *dev = &pdev->dev;
struct ahci_host_priv *hpriv;
+ struct ecx_plat_data *pdata;
struct ata_host *host;
struct resource *mem;
int irq;
- int n_ports;
int i;
int rc;
+ u32 n_ports;
struct ata_port_info pi = ahci_highbank_port_info;
const struct ata_port_info *ppi[] = { &pi, NULL };
dev_err(dev, "can't alloc ahci_host_priv\n");
return -ENOMEM;
}
+ pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL);
+ if (!pdata) {
+ dev_err(dev, "can't alloc ecx_plat_data\n");
+ return -ENOMEM;
+ }
hpriv->flags |= (unsigned long)pi.private_data;
if (hpriv->cap & HOST_CAP_PMP)
pi.flags |= ATA_FLAG_PMP;
- ahci_set_em_messages(hpriv, &pi);
-
/* CAP.NP sometimes indicate the index of the last enabled
* port, at other times, that of the last possible port, so
* determining the maximum port number requires looking at
*/
n_ports = max(ahci_nr_ports(hpriv->cap), fls(hpriv->port_map));
+ pdata->n_ports = n_ports;
+ hpriv->plat_data = pdata;
+ highbank_set_em_messages(dev, hpriv, &pi);
+
host = ata_host_alloc_pinfo(dev, ppi, n_ports);
if (!host) {
rc = -ENOMEM;
if (!(hpriv->cap & HOST_CAP_SSS) || ahci_ignore_sss)
host->flags |= ATA_HOST_PARALLEL_SCAN;
- if (pi.flags & ATA_FLAG_EM)
- ahci_reset_em(host);
-
for (i = 0; i < host->n_ports; i++) {
struct ata_port *ap = host->ports[i];
projects / ~andy / linux / blobdiff