#include <linux/libata.h>
#define DRV_NAME "pata_pdc2027x"
-#define DRV_VERSION "0.9"
+#define DRV_VERSION "1.0"
#undef PDC_DEBUG
#ifdef PDC_DEBUG
.post_internal_cmd = ata_bmdma_post_internal_cmd,
.cable_detect = pdc2027x_cable_detect,
- .irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
.irq_on = ata_irq_on,
.irq_ack = ata_irq_ack,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
.cable_detect = pdc2027x_cable_detect,
- .irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
.irq_on = ata_irq_on,
.irq_ack = ata_irq_ack,
static struct ata_port_info pdc2027x_port_info[] = {
/* PDC_UDMA_100 */
{
- .sht = &pdc2027x_sht,
.flags = ATA_FLAG_NO_LEGACY | ATA_FLAG_SLAVE_POSS |
ATA_FLAG_MMIO,
.pio_mask = 0x1f, /* pio0-4 */
},
/* PDC_UDMA_133 */
{
- .sht = &pdc2027x_sht,
.flags = ATA_FLAG_NO_LEGACY | ATA_FLAG_SLAVE_POSS |
ATA_FLAG_MMIO,
.pio_mask = 0x1f, /* pio0-4 */
/**
* pdc2027x_prereset - prereset for PATA host controller
* @ap: Target port
+ * @deadline: deadline jiffies for the operation
*
* Probeinit including cable detection.
*
* None (inherited from caller).
*/
-static int pdc2027x_prereset(struct ata_port *ap)
+static int pdc2027x_prereset(struct ata_port *ap, unsigned long deadline)
{
/* Check whether port enabled */
if (!pdc2027x_port_enabled(ap))
return -ENOENT;
- return ata_std_prereset(ap);
+ return ata_std_prereset(ap, deadline);
}
/**
/**
* pdc_read_counter - Read the ctr counter
- * @probe_ent: for the port address
+ * @host: target ATA host
*/
-static long pdc_read_counter(struct ata_probe_ent *probe_ent)
+static long pdc_read_counter(struct ata_host *host)
{
- void __iomem *mmio_base = probe_ent->iomap[PDC_MMIO_BAR];
+ void __iomem *mmio_base = host->iomap[PDC_MMIO_BAR];
long counter;
int retry = 1;
u32 bccrl, bccrh, bccrlv, bccrhv;
retry:
- bccrl = readl(mmio_base + PDC_BYTE_COUNT) & 0xffff;
- bccrh = readl(mmio_base + PDC_BYTE_COUNT + 0x100) & 0xffff;
+ bccrl = readl(mmio_base + PDC_BYTE_COUNT) & 0x7fff;
+ bccrh = readl(mmio_base + PDC_BYTE_COUNT + 0x100) & 0x7fff;
rmb();
/* Read the counter values again for verification */
- bccrlv = readl(mmio_base + PDC_BYTE_COUNT) & 0xffff;
- bccrhv = readl(mmio_base + PDC_BYTE_COUNT + 0x100) & 0xffff;
+ bccrlv = readl(mmio_base + PDC_BYTE_COUNT) & 0x7fff;
+ bccrhv = readl(mmio_base + PDC_BYTE_COUNT + 0x100) & 0x7fff;
rmb();
counter = (bccrh << 15) | bccrl;
* adjust_pll - Adjust the PLL input clock in Hz.
*
* @pdc_controller: controller specific information
- * @probe_ent: For the port address
+ * @host: target ATA host
* @pll_clock: The input of PLL in HZ
*/
-static void pdc_adjust_pll(struct ata_probe_ent *probe_ent, long pll_clock, unsigned int board_idx)
+static void pdc_adjust_pll(struct ata_host *host, long pll_clock, unsigned int board_idx)
{
- void __iomem *mmio_base = probe_ent->iomap[PDC_MMIO_BAR];
+ void __iomem *mmio_base = host->iomap[PDC_MMIO_BAR];
u16 pll_ctl;
long pll_clock_khz = pll_clock / 1000;
long pout_required = board_idx? PDC_133_MHZ:PDC_100_MHZ;
/**
* detect_pll_input_clock - Detect the PLL input clock in Hz.
- * @probe_ent: for the port address
+ * @host: target ATA host
* Ex. 16949000 on 33MHz PCI bus for pdc20275.
* Half of the PCI clock.
*/
-static long pdc_detect_pll_input_clock(struct ata_probe_ent *probe_ent)
+static long pdc_detect_pll_input_clock(struct ata_host *host)
{
- void __iomem *mmio_base = probe_ent->iomap[PDC_MMIO_BAR];
+ void __iomem *mmio_base = host->iomap[PDC_MMIO_BAR];
u32 scr;
long start_count, end_count;
- long pll_clock;
-
- /* Read current counter value */
- start_count = pdc_read_counter(probe_ent);
+ struct timeval start_time, end_time;
+ long pll_clock, usec_elapsed;
/* Start the test mode */
scr = readl(mmio_base + PDC_SYS_CTL);
writel(scr | (0x01 << 14), mmio_base + PDC_SYS_CTL);
readl(mmio_base + PDC_SYS_CTL); /* flush */
+ /* Read current counter value */
+ start_count = pdc_read_counter(host);
+ do_gettimeofday(&start_time);
+
/* Let the counter run for 100 ms. */
mdelay(100);
/* Read the counter values again */
- end_count = pdc_read_counter(probe_ent);
+ end_count = pdc_read_counter(host);
+ do_gettimeofday(&end_time);
/* Stop the test mode */
scr = readl(mmio_base + PDC_SYS_CTL);
readl(mmio_base + PDC_SYS_CTL); /* flush */
/* calculate the input clock in Hz */
- pll_clock = (start_count - end_count) * 10;
+ usec_elapsed = (end_time.tv_sec - start_time.tv_sec) * 1000000 +
+ (end_time.tv_usec - start_time.tv_usec);
+
+ pll_clock = ((start_count - end_count) & 0x3fffffff) / 100 *
+ (100000000 / usec_elapsed);
PDPRINTK("start[%ld] end[%ld] \n", start_count, end_count);
PDPRINTK("PLL input clock[%ld]Hz\n", pll_clock);
/**
* pdc_hardware_init - Initialize the hardware.
- * @pdev: instance of pci_dev found
- * @pdc_controller: controller specific information
- * @pe: for the port address
+ * @host: target ATA host
+ * @board_idx: board identifier
*/
-static int pdc_hardware_init(struct pci_dev *pdev, struct ata_probe_ent *pe, unsigned int board_idx)
+static int pdc_hardware_init(struct ata_host *host, unsigned int board_idx)
{
long pll_clock;
* Ex. 25MHz or 40MHz, we have to adjust the cycle_time.
* The pdc20275 controller employs PLL circuit to help correct timing registers setting.
*/
- pll_clock = pdc_detect_pll_input_clock(pe);
+ pll_clock = pdc_detect_pll_input_clock(host);
if (pll_clock < 0) /* counter overflow? Try again. */
- pll_clock = pdc_detect_pll_input_clock(pe);
+ pll_clock = pdc_detect_pll_input_clock(host);
- dev_printk(KERN_INFO, &pdev->dev, "PLL input clock %ld kHz\n", pll_clock/1000);
+ dev_printk(KERN_INFO, host->dev, "PLL input clock %ld kHz\n", pll_clock/1000);
/* Adjust PLL control register */
- pdc_adjust_pll(pe, pll_clock, board_idx);
+ pdc_adjust_pll(host, pll_clock, board_idx);
return 0;
}
* Called when an instance of PCI adapter is inserted.
* This function checks whether the hardware is supported,
* initialize hardware and register an instance of ata_host to
- * libata by providing struct ata_probe_ent and ata_device_add().
- * (implements struct pci_driver.probe() )
+ * libata. (implements struct pci_driver.probe() )
*
* @pdev: instance of pci_dev found
* @ent: matching entry in the id_tbl[]
{
static int printed_version;
unsigned int board_idx = (unsigned int) ent->driver_data;
-
- struct ata_probe_ent *probe_ent;
+ const struct ata_port_info *ppi[] =
+ { &pdc2027x_port_info[board_idx], NULL };
+ struct ata_host *host;
void __iomem *mmio_base;
int rc;
if (!printed_version++)
dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n");
+ /* alloc host */
+ host = ata_host_alloc_pinfo(&pdev->dev, ppi, 2);
+ if (!host)
+ return -ENOMEM;
+
+ /* acquire resources and fill host */
rc = pcim_enable_device(pdev);
if (rc)
return rc;
rc = pcim_iomap_regions(pdev, 1 << PDC_MMIO_BAR, DRV_NAME);
if (rc)
return rc;
+ host->iomap = pcim_iomap_table(pdev);
rc = pci_set_dma_mask(pdev, ATA_DMA_MASK);
if (rc)
if (rc)
return rc;
- /* Prepare the probe entry */
- probe_ent = devm_kzalloc(&pdev->dev, sizeof(*probe_ent), GFP_KERNEL);
- if (probe_ent == NULL)
- return -ENOMEM;
-
- probe_ent->dev = pci_dev_to_dev(pdev);
- INIT_LIST_HEAD(&probe_ent->node);
-
- probe_ent->sht = pdc2027x_port_info[board_idx].sht;
- probe_ent->port_flags = pdc2027x_port_info[board_idx].flags;
- probe_ent->pio_mask = pdc2027x_port_info[board_idx].pio_mask;
- probe_ent->mwdma_mask = pdc2027x_port_info[board_idx].mwdma_mask;
- probe_ent->udma_mask = pdc2027x_port_info[board_idx].udma_mask;
- probe_ent->port_ops = pdc2027x_port_info[board_idx].port_ops;
-
- probe_ent->irq = pdev->irq;
- probe_ent->irq_flags = IRQF_SHARED;
- probe_ent->iomap = pcim_iomap_table(pdev);
-
- mmio_base = probe_ent->iomap[PDC_MMIO_BAR];
+ mmio_base = host->iomap[PDC_MMIO_BAR];
- pdc_ata_setup_port(&probe_ent->port[0], mmio_base + 0x17c0);
- probe_ent->port[0].bmdma_addr = mmio_base + 0x1000;
- pdc_ata_setup_port(&probe_ent->port[1], mmio_base + 0x15c0);
- probe_ent->port[1].bmdma_addr = mmio_base + 0x1008;
+ pdc_ata_setup_port(&host->ports[0]->ioaddr, mmio_base + 0x17c0);
+ host->ports[0]->ioaddr.bmdma_addr = mmio_base + 0x1000;
+ pdc_ata_setup_port(&host->ports[1]->ioaddr, mmio_base + 0x15c0);
+ host->ports[1]->ioaddr.bmdma_addr = mmio_base + 0x1008;
- probe_ent->n_ports = 2;
-
- pci_set_master(pdev);
//pci_enable_intx(pdev);
/* initialize adapter */
- if (pdc_hardware_init(pdev, probe_ent, board_idx) != 0)
+ if (pdc_hardware_init(host, board_idx) != 0)
return -EIO;
- if (!ata_device_add(probe_ent))
- return -ENODEV;
-
- devm_kfree(&pdev->dev, probe_ent);
- return 0;
+ pci_set_master(pdev);
+ return ata_host_activate(host, pdev->irq, ata_interrupt, IRQF_SHARED,
+ &pdc2027x_sht);
}
/**
projects / ~andy / linux / blobdiff