source "net/Kconfig"
-source "drivers/base/Kconfig"
-
-source "drivers/mtd/Kconfig"
-
-source "drivers/block/Kconfig"
-
-source "drivers/ide/Kconfig"
+source "drivers/Kconfig"
source "arch/h8300/Kconfig.ide"
-source "drivers/net/Kconfig"
-
-#
-# input - input/joystick depends on it. As does USB.
-#
-source "drivers/input/Kconfig"
-
-menu "Character devices"
-
-config VT
- bool "Virtual terminal"
- ---help---
- If you say Y here, you will get support for terminal devices with
- display and keyboard devices. These are called "virtual" because you
- can run several virtual terminals (also called virtual consoles) on
- one physical terminal. This is rather useful, for example one
- virtual terminal can collect system messages and warnings, another
- one can be used for a text-mode user session, and a third could run
- an X session, all in parallel. Switching between virtual terminals
- is done with certain key combinations, usually Alt-<function key>.
-
- The setterm command ("man setterm") can be used to change the
- properties (such as colors or beeping) of a virtual terminal. The
- man page console_codes(4) ("man console_codes") contains the special
- character sequences that can be used to change those properties
- directly. The fonts used on virtual terminals can be changed with
- the setfont ("man setfont") command and the key bindings are defined
- with the loadkeys ("man loadkeys") command.
-
- You need at least one virtual terminal device in order to make use
- of your keyboard and monitor. Therefore, only people configuring an
- embedded system would want to say N here in order to save some
- memory; the only way to log into such a system is then via a serial
- or network connection.
-
- If unsure, say Y, or else you won't be able to do much with your new
- shiny Linux system :-)
-
-config VT_CONSOLE
- bool "Support for console on virtual terminal"
- depends on VT
- ---help---
- The system console is the device which receives all kernel messages
- and warnings and which allows logins in single user mode. If you
- answer Y here, a virtual terminal (the device used to interact with
- a physical terminal) can be used as system console. This is the most
- common mode of operations, so you should say Y here unless you want
- the kernel messages be output only to a serial port (in which case
- you should say Y to "Console on serial port", below).
-
- If you do say Y here, by default the currently visible virtual
- terminal (/dev/tty0) will be used as system console. You can change
- that with a kernel command line option such as "console=tty3" which
- would use the third virtual terminal as system console. (Try "man
- bootparam" or see the documentation of your boot loader (lilo or
- loadlin) about how to pass options to the kernel at boot time.)
-
- If unsure, say Y.
-
-config HW_CONSOLE
- bool
- depends on VT
- default y
-
-comment "Unix98 PTY support"
-
-config UNIX98_PTYS
- bool "Unix98 PTY support"
- ---help---
- A pseudo terminal (PTY) is a software device consisting of two
- halves: a master and a slave. The slave device behaves identical to
- a physical terminal; the master device is used by a process to
- read data from and write data to the slave, thereby emulating a
- terminal. Typical programs for the master side are telnet servers
- and xterms.
-
- Linux has traditionally used the BSD-like names /dev/ptyxx for
- masters and /dev/ttyxx for slaves of pseudo terminals. This scheme
- has a number of problems. The GNU C library glibc 2.1 and later,
- however, supports the Unix98 naming standard: in order to acquire a
- pseudo terminal, a process opens /dev/ptmx; the number of the pseudo
- terminal is then made available to the process and the pseudo
- terminal slave can be accessed as /dev/pts/<number>. What was
- traditionally /dev/ttyp2 will then be /dev/pts/2, for example.
-
- The entries in /dev/pts/ are created on the fly by a virtual
- file system; therefore, if you say Y here you should say Y to
- "/dev/pts file system for Unix98 PTYs" as well.
-
- If you want to say Y here, you need to have the C library glibc 2.1
- or later (equal to libc-6.1, check with "ls -l /lib/libc.so.*").
- Read the instructions in <file:Documentation/Changes> pertaining to
- pseudo terminals. It's safe to say N.
-
-source "drivers/char/pcmcia/Kconfig"
-
-source "drivers/tty/serial/Kconfig"
-
-source "drivers/i2c/Kconfig"
-
-source "drivers/hwmon/Kconfig"
-
-source "drivers/usb/Kconfig"
-
-source "drivers/uwb/Kconfig"
-
-endmenu
-
-source "drivers/staging/Kconfig"
-
source "fs/Kconfig"
source "arch/h8300/Kconfig.debug"
projects / ~andy / linux / blobdiff