-/* $Id: dram_init.S,v 1.4 2003/09/22 09:21:59 starvik Exp $
- *
+/*
* DRAM/SDRAM initialization - alter with care
* This file is intended to be included from other assembler files
*
* Note: This file may not modify r9 because r9 is used to carry
* information from the decompresser to the kernel
*
- * Copyright (C) 2000, 2001 Axis Communications AB
- *
- * Authors: Mikael Starvik (starvik@axis.com)
- *
- * $Log: dram_init.S,v $
- * Revision 1.4 2003/09/22 09:21:59 starvik
- * Decompresser is linked to 0x407xxxxx and sdram commands are at 0x000xxxxx
- * so we need to mask off 12 bits.
- *
- * Revision 1.3 2003/03/31 09:38:37 starvik
- * Corrected calculation of end of sdram init commands
- *
- * Revision 1.2 2002/11/19 13:33:29 starvik
- * Changes from Linux 2.4
- *
- * Revision 1.13 2002/10/30 07:42:28 starvik
- * Always read SDRAM command sequence from flash
- *
- * Revision 1.12 2002/08/09 11:37:37 orjanf
- * Added double initialization work-around for Samsung SDRAMs.
- *
- * Revision 1.11 2002/06/04 11:43:21 starvik
- * Check if mrs_data is specified in kernelconfig (necessary for MCM)
- *
- * Revision 1.10 2001/10/04 12:00:21 martinnn
- * Added missing underscores.
- *
- * Revision 1.9 2001/10/01 14:47:35 bjornw
- * Added register prefixes and removed underscores
- *
- * Revision 1.8 2001/05/15 07:12:45 hp
- * Copy warning from head.S about r8 and r9
- *
- * Revision 1.7 2001/04/18 12:05:39 bjornw
- * Fixed comments, and explicitely include config.h to be sure its there
- *
- * Revision 1.6 2001/04/10 06:20:16 starvik
- * Delay should be 200us, not 200ns
- *
- * Revision 1.5 2001/04/09 06:01:13 starvik
- * Added support for 100 MHz SDRAMs
- *
- * Revision 1.4 2001/03/26 14:24:01 bjornw
- * Namechange of some config options
- *
- * Revision 1.3 2001/03/23 08:29:41 starvik
- * Corrected calculation of mrs_data
- *
- * Revision 1.2 2001/02/08 15:20:00 starvik
- * Corrected SDRAM initialization
- * Should now be included as inline
- *
- * Revision 1.1 2001/01/29 13:08:02 starvik
- * Initial version
- * This file should be included from all assembler files that needs to
- * initialize DRAM/SDRAM.
+ * Copyright (C) 2000-2012 Axis Communications AB
*
*/
/* Just to be certain the config file is included, we include it here
- * explicitely instead of depending on it being included in the file that
+ * explicitly instead of depending on it being included in the file that
* uses this code.
*/
;; WARNING! The registers r8 and r9 are used as parameters carrying
- ;; information from the decompressor (if the kernel was compressed).
+ ;; information from the decompressor (if the kernel was compressed).
;; They should not be used in the code below.
-#ifndef CONFIG_SVINTO_SIM
move.d CONFIG_ETRAX_DEF_R_WAITSTATES, $r0
move.d $r0, [R_WAITSTATES]
move.d CONFIG_ETRAX_DEF_R_BUS_CONFIG, $r0
move.d $r0, [R_BUS_CONFIG]
-
+
#ifndef CONFIG_ETRAX_SDRAM
move.d CONFIG_ETRAX_DEF_R_DRAM_CONFIG, $r0
move.d $r0, [R_DRAM_CONFIG]
;; Samsung SDRAMs seem to require to be initialized twice to work properly.
moveq 2, $r6
_sdram_init:
-
+
; Refer to ETRAX 100LX Designers Reference for a description of SDRAM initialization
-
+
; Bank configuration
move.d CONFIG_ETRAX_DEF_R_SDRAM_CONFIG, $r0
move.d $r0, [R_SDRAM_CONFIG]
- ; Calculate value of mrs_data
+ ; Calculate value of mrs_data
; CAS latency = 2 && bus_width = 32 => 0x40
; CAS latency = 3 && bus_width = 32 => 0x60
; CAS latency = 2 && bus_width = 16 => 0x20
and.d 0x00ff0000, $r2
bne _set_timing
lsrq 16, $r2
-
+
move.d 0x40, $r2 ; Assume 32 bits and CAS latency = 2
move.d CONFIG_ETRAX_DEF_R_SDRAM_TIMING, $r1
move.d $r1, $r3
- and.d 0x03, $r1 ; Get CAS latency
+ and.d 0x03, $r1 ; Get CAS latency
and.d 0x1000, $r3 ; 50 or 100 MHz?
beq _speed_50
nop
-_speed_100:
+_speed_100:
cmp.d 0x00, $r1 ; CAS latency = 2?
beq _bw_check
nop
- or.d 0x20, $r2 ; CAS latency = 3
+ or.d 0x20, $r2 ; CAS latency = 3
ba _bw_check
nop
-_speed_50:
+_speed_50:
cmp.d 0x01, $r1 ; CAS latency = 2?
beq _bw_check
nop
; Set timing parameters. Starts master clock
_set_timing:
move.d CONFIG_ETRAX_DEF_R_SDRAM_TIMING, $r1
- and.d 0x8000f9ff, $r1 ; Make sure mrs data and command is 0
+ and.d 0x8000f9ff, $r1 ; Make sure mrs data and command is 0
or.d 0x80000000, $r1 ; Make sure sdram enable bit is set
move.d $r1, $r5
or.d 0x0000c000, $r1 ; ref = disable
lslq 16, $r2 ; mrs data starts at bit 16
- or.d $r2, $r1
- move.d $r1, [R_SDRAM_TIMING]
-
+ or.d $r2, $r1
+ move.d $r1, [R_SDRAM_TIMING]
+
; Wait 200us
move.d 10000, $r2
1: bne 1b
subq 1, $r2
-
+
; Issue initialization command sequence
move.d _sdram_commands_start, $r2
and.d 0x000fffff, $r2 ; Make sure commands are read from flash
.byte 2 ; refresh
.byte 0 ; nop
.byte 1 ; mrs
- .byte 0 ; nop
-_sdram_commands_end:
-#endif
+ .byte 0 ; nop
+_sdram_commands_end:
#endif