/****************************************************************************** * * This file is provided under a dual BSD/GPLv2 license. When using or * redistributing this file, you may do so under either license. * * GPL LICENSE SUMMARY * * Copyright(c) 2005 - 2007 Intel Corporation. All rights reserved. * * This program is free software; you can redistribute it and/or modify * it under the terms of version 2 of the GNU General Public License as * published by the Free Software Foundation. * * This program is distributed in the hope that it will be useful, but * WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU * General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110, * USA * * The full GNU General Public License is included in this distribution * in the file called LICENSE.GPL. * * Contact Information: * James P. Ketrenos * Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 * * BSD LICENSE * * Copyright(c) 2005 - 2007 Intel Corporation. All rights reserved. * All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * * * Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * * Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in * the documentation and/or other materials provided with the * distribution. * * Neither the name Intel Corporation nor the names of its * contributors may be used to endorse or promote products derived * from this software without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. * *****************************************************************************/ /* * Please use this file (iwl-4965-hw.h) only for hardware-related definitions. * Use iwl-4965-commands.h for uCode API definitions. * Use iwl-4965.h for driver implementation definitions. */ #ifndef __iwl_4965_hw_h__ #define __iwl_4965_hw_h__ /* * uCode queue management definitions ... * Queue #4 is the command queue for 3945 and 4965; map it to Tx FIFO chnl 4. * The first queue used for block-ack aggregation is #7 (4965 only). * All block-ack aggregation queues should map to Tx DMA/FIFO channel 7. */ #define IWL_CMD_QUEUE_NUM 4 #define IWL_CMD_FIFO_NUM 4 #define IWL_BACK_QUEUE_FIRST_ID 7 /* Tx rates */ #define IWL_CCK_RATES 4 #define IWL_OFDM_RATES 8 #define IWL_HT_RATES 16 #define IWL_MAX_RATES (IWL_CCK_RATES+IWL_OFDM_RATES+IWL_HT_RATES) /* Time constants */ #define SHORT_SLOT_TIME 9 #define LONG_SLOT_TIME 20 /* RSSI to dBm */ #define IWL_RSSI_OFFSET 44 /* * EEPROM related constants, enums, and structures. */ /* * EEPROM access time values: * * Driver initiates EEPROM read by writing byte address << 1 to CSR_EEPROM_REG, * then clearing (with subsequent read/modify/write) CSR_EEPROM_REG bit * CSR_EEPROM_REG_BIT_CMD (0x2). * Driver then polls CSR_EEPROM_REG for CSR_EEPROM_REG_READ_VALID_MSK (0x1). * When polling, wait 10 uSec between polling loops, up to a maximum 5000 uSec. * Driver reads 16-bit value from bits 31-16 of CSR_EEPROM_REG. */ #define IWL_EEPROM_ACCESS_TIMEOUT 5000 /* uSec */ #define IWL_EEPROM_ACCESS_DELAY 10 /* uSec */ /* * Regulatory channel usage flags in EEPROM struct iwl4965_eeprom_channel.flags. * * IBSS and/or AP operation is allowed *only* on those channels with * (VALID && IBSS && ACTIVE && !RADAR). This restriction is in place because * RADAR detection is not supported by the 4965 driver, but is a * requirement for establishing a new network for legal operation on channels * requiring RADAR detection or restricting ACTIVE scanning. * * NOTE: "WIDE" flag does not indicate anything about "FAT" 40 MHz channels. * It only indicates that 20 MHz channel use is supported; FAT channel * usage is indicated by a separate set of regulatory flags for each * FAT channel pair. * * NOTE: Using a channel inappropriately will result in a uCode error! */ enum { EEPROM_CHANNEL_VALID = (1 << 0), /* usable for this SKU/geo */ EEPROM_CHANNEL_IBSS = (1 << 1), /* usable as an IBSS channel */ /* Bit 2 Reserved */ EEPROM_CHANNEL_ACTIVE = (1 << 3), /* active scanning allowed */ EEPROM_CHANNEL_RADAR = (1 << 4), /* radar detection required */ EEPROM_CHANNEL_WIDE = (1 << 5), /* 20 MHz channel okay */ EEPROM_CHANNEL_NARROW = (1 << 6), /* 10 MHz channel (not used) */ EEPROM_CHANNEL_DFS = (1 << 7), /* dynamic freq selection candidate */ }; /* SKU Capabilities */ #define EEPROM_SKU_CAP_SW_RF_KILL_ENABLE (1 << 0) #define EEPROM_SKU_CAP_HW_RF_KILL_ENABLE (1 << 1) /* *regulatory* channel data format in eeprom, one for each channel. * There are separate entries for FAT (40 MHz) vs. normal (20 MHz) channels. */ struct iwl4965_eeprom_channel { u8 flags; /* EEPROM_CHANNEL_* flags copied from EEPROM */ s8 max_power_avg; /* max power (dBm) on this chnl, limit 31 */ } __attribute__ ((packed)); /* 4965 has two radio transmitters (and 3 radio receivers) */ #define EEPROM_TX_POWER_TX_CHAINS (2) /* 4965 has room for up to 8 sets of txpower calibration data */ #define EEPROM_TX_POWER_BANDS (8) /* 4965 factory calibration measures txpower gain settings for * each of 3 target output levels */ #define EEPROM_TX_POWER_MEASUREMENTS (3) /* 4965 driver does not work with txpower calibration version < 5. * Look for this in calib_version member of struct iwl4965_eeprom. */ #define EEPROM_TX_POWER_VERSION_NEW (5) /* * 4965 factory calibration data for one txpower level, on one channel, * measured on one of the 2 tx chains (radio transmitter and associated * antenna). EEPROM contains: * * 1) Temperature (degrees Celsius) of device when measurement was made. * * 2) Gain table index used to achieve the target measurement power. * This refers to the "well-known" gain tables (see iwl-4965-hw.h). * * 3) Actual measured output power, in half-dBm ("34" = 17 dBm). * * 4) RF power amplifier detector level measurement (not used). */ struct iwl4965_eeprom_calib_measure { u8 temperature; /* Device temperature (Celsius) */ u8 gain_idx; /* Index into gain table */ u8 actual_pow; /* Measured RF output power, half-dBm */ s8 pa_det; /* Power amp detector level (not used) */ } __attribute__ ((packed)); /* * 4965 measurement set for one channel. EEPROM contains: * * 1) Channel number measured * * 2) Measurements for each of 3 power levels for each of 2 radio transmitters * (a.k.a. "tx chains") (6 measurements altogether) */ struct iwl4965_eeprom_calib_ch_info { u8 ch_num; struct iwl4965_eeprom_calib_measure measurements[EEPROM_TX_POWER_TX_CHAINS] [EEPROM_TX_POWER_MEASUREMENTS]; } __attribute__ ((packed)); /* * 4965 txpower subband info. * * For each frequency subband, EEPROM contains the following: * * 1) First and last channels within range of the subband. "0" values * indicate that this sample set is not being used. * * 2) Sample measurement sets for 2 channels close to the range endpoints. */ struct iwl4965_eeprom_calib_subband_info { u8 ch_from; /* channel number of lowest channel in subband */ u8 ch_to; /* channel number of highest channel in subband */ struct iwl4965_eeprom_calib_ch_info ch1; struct iwl4965_eeprom_calib_ch_info ch2; } __attribute__ ((packed)); /* * 4965 txpower calibration info. EEPROM contains: * * 1) Factory-measured saturation power levels (maximum levels at which * tx power amplifier can output a signal without too much distortion). * There is one level for 2.4 GHz band and one for 5 GHz band. These * values apply to all channels within each of the bands. * * 2) Factory-measured power supply voltage level. This is assumed to be * constant (i.e. same value applies to all channels/bands) while the * factory measurements are being made. * * 3) Up to 8 sets of factory-measured txpower calibration values. * These are for different frequency ranges, since txpower gain * characteristics of the analog radio circuitry vary with frequency. * * Not all sets need to be filled with data; * struct iwl4965_eeprom_calib_subband_info contains range of channels * (0 if unused) for each set of data. */ struct iwl4965_eeprom_calib_info { u8 saturation_power24; /* half-dBm (e.g. "34" = 17 dBm) */ u8 saturation_power52; /* half-dBm */ s16 voltage; /* signed */ struct iwl4965_eeprom_calib_subband_info band_info[EEPROM_TX_POWER_BANDS]; } __attribute__ ((packed)); /* * 4965 EEPROM map */ struct iwl4965_eeprom { u8 reserved0[16]; #define EEPROM_DEVICE_ID (2*0x08) /* 2 bytes */ u16 device_id; /* abs.ofs: 16 */ u8 reserved1[2]; #define EEPROM_PMC (2*0x0A) /* 2 bytes */ u16 pmc; /* abs.ofs: 20 */ u8 reserved2[20]; #define EEPROM_MAC_ADDRESS (2*0x15) /* 6 bytes */ u8 mac_address[6]; /* abs.ofs: 42 */ u8 reserved3[58]; #define EEPROM_BOARD_REVISION (2*0x35) /* 2 bytes */ u16 board_revision; /* abs.ofs: 106 */ u8 reserved4[11]; #define EEPROM_BOARD_PBA_NUMBER (2*0x3B+1) /* 9 bytes */ u8 board_pba_number[9]; /* abs.ofs: 119 */ u8 reserved5[8]; #define EEPROM_VERSION (2*0x44) /* 2 bytes */ u16 version; /* abs.ofs: 136 */ #define EEPROM_SKU_CAP (2*0x45) /* 1 bytes */ u8 sku_cap; /* abs.ofs: 138 */ #define EEPROM_LEDS_MODE (2*0x45+1) /* 1 bytes */ u8 leds_mode; /* abs.ofs: 139 */ #define EEPROM_OEM_MODE (2*0x46) /* 2 bytes */ u16 oem_mode; #define EEPROM_WOWLAN_MODE (2*0x47) /* 2 bytes */ u16 wowlan_mode; /* abs.ofs: 142 */ #define EEPROM_LEDS_TIME_INTERVAL (2*0x48) /* 2 bytes */ u16 leds_time_interval; /* abs.ofs: 144 */ #define EEPROM_LEDS_OFF_TIME (2*0x49) /* 1 bytes */ u8 leds_off_time; /* abs.ofs: 146 */ #define EEPROM_LEDS_ON_TIME (2*0x49+1) /* 1 bytes */ u8 leds_on_time; /* abs.ofs: 147 */ #define EEPROM_ALMGOR_M_VERSION (2*0x4A) /* 1 bytes */ u8 almgor_m_version; /* abs.ofs: 148 */ #define EEPROM_ANTENNA_SWITCH_TYPE (2*0x4A+1) /* 1 bytes */ u8 antenna_switch_type; /* abs.ofs: 149 */ u8 reserved6[8]; #define EEPROM_4965_BOARD_REVISION (2*0x4F) /* 2 bytes */ u16 board_revision_4965; /* abs.ofs: 158 */ u8 reserved7[13]; #define EEPROM_4965_BOARD_PBA (2*0x56+1) /* 9 bytes */ u8 board_pba_number_4965[9]; /* abs.ofs: 173 */ u8 reserved8[10]; #define EEPROM_REGULATORY_SKU_ID (2*0x60) /* 4 bytes */ u8 sku_id[4]; /* abs.ofs: 192 */ /* * Per-channel regulatory data. * * Each channel that *might* be supported by 3945 or 4965 has a fixed location * in EEPROM containing EEPROM_CHANNEL_* usage flags (LSB) and max regulatory * txpower (MSB). * * Entries immediately below are for 20 MHz channel width. FAT (40 MHz) * channels (only for 4965, not supported by 3945) appear later in the EEPROM. * * 2.4 GHz channels 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14 */ #define EEPROM_REGULATORY_BAND_1 (2*0x62) /* 2 bytes */ u16 band_1_count; /* abs.ofs: 196 */ #define EEPROM_REGULATORY_BAND_1_CHANNELS (2*0x63) /* 28 bytes */ struct iwl4965_eeprom_channel band_1_channels[14]; /* abs.ofs: 196 */ /* * 4.9 GHz channels 183, 184, 185, 187, 188, 189, 192, 196, * 5.0 GHz channels 7, 8, 11, 12, 16 * (4915-5080MHz) (none of these is ever supported) */ #define EEPROM_REGULATORY_BAND_2 (2*0x71) /* 2 bytes */ u16 band_2_count; /* abs.ofs: 226 */ #define EEPROM_REGULATORY_BAND_2_CHANNELS (2*0x72) /* 26 bytes */ struct iwl4965_eeprom_channel band_2_channels[13]; /* abs.ofs: 228 */ /* * 5.2 GHz channels 34, 36, 38, 40, 42, 44, 46, 48, 52, 56, 60, 64 * (5170-5320MHz) */ #define EEPROM_REGULATORY_BAND_3 (2*0x7F) /* 2 bytes */ u16 band_3_count; /* abs.ofs: 254 */ #define EEPROM_REGULATORY_BAND_3_CHANNELS (2*0x80) /* 24 bytes */ struct iwl4965_eeprom_channel band_3_channels[12]; /* abs.ofs: 256 */ /* * 5.5 GHz channels 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140 * (5500-5700MHz) */ #define EEPROM_REGULATORY_BAND_4 (2*0x8C) /* 2 bytes */ u16 band_4_count; /* abs.ofs: 280 */ #define EEPROM_REGULATORY_BAND_4_CHANNELS (2*0x8D) /* 22 bytes */ struct iwl4965_eeprom_channel band_4_channels[11]; /* abs.ofs: 282 */ /* * 5.7 GHz channels 145, 149, 153, 157, 161, 165 * (5725-5825MHz) */ #define EEPROM_REGULATORY_BAND_5 (2*0x98) /* 2 bytes */ u16 band_5_count; /* abs.ofs: 304 */ #define EEPROM_REGULATORY_BAND_5_CHANNELS (2*0x99) /* 12 bytes */ struct iwl4965_eeprom_channel band_5_channels[6]; /* abs.ofs: 306 */ u8 reserved10[2]; /* * 2.4 GHz FAT channels 1 (5), 2 (6), 3 (7), 4 (8), 5 (9), 6 (10), 7 (11) * * The channel listed is the center of the lower 20 MHz half of the channel. * The overall center frequency is actually 2 channels (10 MHz) above that, * and the upper half of each FAT channel is centered 4 channels (20 MHz) away * from the lower half; e.g. the upper half of FAT channel 1 is channel 5, * and the overall FAT channel width centers on channel 3. * * NOTE: The RXON command uses 20 MHz channel numbers to specify the * control channel to which to tune. RXON also specifies whether the * control channel is the upper or lower half of a FAT channel. * * NOTE: 4965 does not support FAT channels on 2.4 GHz. */ #define EEPROM_REGULATORY_BAND_24_FAT_CHANNELS (2*0xA0) /* 14 bytes */ struct iwl4965_eeprom_channel band_24_channels[7]; /* abs.ofs: 320 */ u8 reserved11[2]; /* * 5.2 GHz FAT channels 36 (40), 44 (48), 52 (56), 60 (64), * 100 (104), 108 (112), 116 (120), 124 (128), 132 (136), 149 (153), 157 (161) */ #define EEPROM_REGULATORY_BAND_52_FAT_CHANNELS (2*0xA8) /* 22 bytes */ struct iwl4965_eeprom_channel band_52_channels[11]; /* abs.ofs: 336 */ u8 reserved12[6]; /* * 4965 driver requires txpower calibration format version 5 or greater. * Driver does not work with txpower calibration version < 5. * This value is simply a 16-bit number, no major/minor versions here. */ #define EEPROM_CALIB_VERSION_OFFSET (2*0xB6) /* 2 bytes */ u16 calib_version; /* abs.ofs: 364 */ u8 reserved13[2]; u8 reserved14[96]; /* abs.ofs: 368 */ /* * 4965 Txpower calibration data. */ #define EEPROM_IWL_CALIB_TXPOWER_OFFSET (2*0xE8) /* 48 bytes */ struct iwl4965_eeprom_calib_info calib_info; /* abs.ofs: 464 */ u8 reserved16[140]; /* fill out to full 1024 byte block */ } __attribute__ ((packed)); #define IWL_EEPROM_IMAGE_SIZE 1024 /* End of EEPROM */ #include "iwl-4965-commands.h" #define PCI_LINK_CTRL 0x0F0 #define PCI_POWER_SOURCE 0x0C8 #define PCI_REG_WUM8 0x0E8 #define PCI_CFG_PMC_PME_FROM_D3COLD_SUPPORT (0x80000000) /*=== CSR (control and status registers) ===*/ #define CSR_BASE (0x000) #define CSR_SW_VER (CSR_BASE+0x000) #define CSR_HW_IF_CONFIG_REG (CSR_BASE+0x000) /* hardware interface config */ #define CSR_INT_COALESCING (CSR_BASE+0x004) /* accum ints, 32-usec units */ #define CSR_INT (CSR_BASE+0x008) /* host interrupt status/ack */ #define CSR_INT_MASK (CSR_BASE+0x00c) /* host interrupt enable */ #define CSR_FH_INT_STATUS (CSR_BASE+0x010) /* busmaster int status/ack*/ #define CSR_GPIO_IN (CSR_BASE+0x018) /* read external chip pins */ #define CSR_RESET (CSR_BASE+0x020) /* busmaster enable, NMI, etc*/ #define CSR_GP_CNTRL (CSR_BASE+0x024) /* * Hardware revision info * Bit fields: * 31-8: Reserved * 7-4: Type of device: 0x0 = 4965, 0xd = 3945 * 3-2: Revision step: 0 = A, 1 = B, 2 = C, 3 = D * 1-0: "Dash" value, as in A-1, etc. * * NOTE: Revision step affects calculation of CCK txpower for 4965. */ #define CSR_HW_REV (CSR_BASE+0x028) /* EEPROM reads */ #define CSR_EEPROM_REG (CSR_BASE+0x02c) #define CSR_EEPROM_GP (CSR_BASE+0x030) #define CSR_GP_UCODE (CSR_BASE+0x044) #define CSR_UCODE_DRV_GP1 (CSR_BASE+0x054) #define CSR_UCODE_DRV_GP1_SET (CSR_BASE+0x058) #define CSR_UCODE_DRV_GP1_CLR (CSR_BASE+0x05c) #define CSR_UCODE_DRV_GP2 (CSR_BASE+0x060) #define CSR_GIO_CHICKEN_BITS (CSR_BASE+0x100) /* * Indicates hardware rev, to determine CCK backoff for txpower calculation. * Bit fields: * 3-2: 0 = A, 1 = B, 2 = C, 3 = D step */ #define CSR_HW_REV_WA_REG (CSR_BASE+0x22C) /* interrupt flags in INTA, set by uCode or hardware (e.g. dma), * acknowledged (reset) by host writing "1" to flagged bits. */ #define CSR_INT_BIT_FH_RX (1<<31) /* Rx DMA, cmd responses, FH_INT[17:16] */ #define CSR_INT_BIT_HW_ERR (1<<29) /* DMA hardware error FH_INT[31] */ #define CSR_INT_BIT_DNLD (1<<28) /* uCode Download */ #define CSR_INT_BIT_FH_TX (1<<27) /* Tx DMA FH_INT[1:0] */ #define CSR_INT_BIT_MAC_CLK_ACTV (1<<26) /* NIC controller's clock toggled on/off */ #define CSR_INT_BIT_SW_ERR (1<<25) /* uCode error */ #define CSR_INT_BIT_RF_KILL (1<<7) /* HW RFKILL switch GP_CNTRL[27] toggled */ #define CSR_INT_BIT_CT_KILL (1<<6) /* Critical temp (chip too hot) rfkill */ #define CSR_INT_BIT_SW_RX (1<<3) /* Rx, command responses, 3945 */ #define CSR_INT_BIT_WAKEUP (1<<1) /* NIC controller waking up (pwr mgmt) */ #define CSR_INT_BIT_ALIVE (1<<0) /* uCode interrupts once it initializes */ #define CSR_INI_SET_MASK (CSR_INT_BIT_FH_RX | \ CSR_INT_BIT_HW_ERR | \ CSR_INT_BIT_FH_TX | \ CSR_INT_BIT_SW_ERR | \ CSR_INT_BIT_RF_KILL | \ CSR_INT_BIT_SW_RX | \ CSR_INT_BIT_WAKEUP | \ CSR_INT_BIT_ALIVE) /* interrupt flags in FH (flow handler) (PCI busmaster DMA) */ #define CSR_FH_INT_BIT_ERR (1<<31) /* Error */ #define CSR_FH_INT_BIT_HI_PRIOR (1<<30) /* High priority Rx, bypass coalescing */ #define CSR_FH_INT_BIT_RX_CHNL1 (1<<17) /* Rx channel 1 */ #define CSR_FH_INT_BIT_RX_CHNL0 (1<<16) /* Rx channel 0 */ #define CSR_FH_INT_BIT_TX_CHNL1 (1<<1) /* Tx channel 1 */ #define CSR_FH_INT_BIT_TX_CHNL0 (1<<0) /* Tx channel 0 */ #define CSR_FH_INT_RX_MASK (CSR_FH_INT_BIT_HI_PRIOR | \ CSR_FH_INT_BIT_RX_CHNL1 | \ CSR_FH_INT_BIT_RX_CHNL0) #define CSR_FH_INT_TX_MASK (CSR_FH_INT_BIT_TX_CHNL1 | \ CSR_FH_INT_BIT_TX_CHNL0) /* RESET */ #define CSR_RESET_REG_FLAG_NEVO_RESET (0x00000001) #define CSR_RESET_REG_FLAG_FORCE_NMI (0x00000002) #define CSR_RESET_REG_FLAG_SW_RESET (0x00000080) #define CSR_RESET_REG_FLAG_MASTER_DISABLED (0x00000100) #define CSR_RESET_REG_FLAG_STOP_MASTER (0x00000200) /* GP (general purpose) CONTROL */ #define CSR_GP_CNTRL_REG_FLAG_MAC_CLOCK_READY (0x00000001) #define CSR_GP_CNTRL_REG_FLAG_INIT_DONE (0x00000004) #define CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ (0x00000008) #define CSR_GP_CNTRL_REG_FLAG_GOING_TO_SLEEP (0x00000010) #define CSR_GP_CNTRL_REG_VAL_MAC_ACCESS_EN (0x00000001) #define CSR_GP_CNTRL_REG_MSK_POWER_SAVE_TYPE (0x07000000) #define CSR_GP_CNTRL_REG_FLAG_MAC_POWER_SAVE (0x04000000) #define CSR_GP_CNTRL_REG_FLAG_HW_RF_KILL_SW (0x08000000) /* EEPROM REG */ #define CSR_EEPROM_REG_READ_VALID_MSK (0x00000001) #define CSR_EEPROM_REG_BIT_CMD (0x00000002) /* EEPROM GP */ #define CSR_EEPROM_GP_VALID_MSK (0x00000006) #define CSR_EEPROM_GP_BAD_SIGNATURE (0x00000000) #define CSR_EEPROM_GP_IF_OWNER_MSK (0x00000180) /* UCODE DRV GP */ #define CSR_UCODE_DRV_GP1_BIT_MAC_SLEEP (0x00000001) #define CSR_UCODE_SW_BIT_RFKILL (0x00000002) #define CSR_UCODE_DRV_GP1_BIT_CMD_BLOCKED (0x00000004) #define CSR_UCODE_DRV_GP1_REG_BIT_CT_KILL_EXIT (0x00000008) /* GPIO */ #define CSR_GPIO_IN_BIT_AUX_POWER (0x00000200) #define CSR_GPIO_IN_VAL_VAUX_PWR_SRC (0x00000000) #define CSR_GPIO_IN_VAL_VMAIN_PWR_SRC CSR_GPIO_IN_BIT_AUX_POWER /* GI Chicken Bits */ #define CSR_GIO_CHICKEN_BITS_REG_BIT_L1A_NO_L0S_RX (0x00800000) #define CSR_GIO_CHICKEN_BITS_REG_BIT_DIS_L0S_EXIT_TIMER (0x20000000) /*=== HBUS (Host-side Bus) ===*/ #define HBUS_BASE (0x400) /* * Registers for accessing device's internal SRAM memory (e.g. SCD SRAM * structures, error log, event log, verifying uCode load). * First write to address register, then read from or write to data register * to complete the job. Once the address register is set up, accesses to * data registers auto-increment the address by one dword. * Bit usage for address registers (read or write): * 0-31: memory address within device */ #define HBUS_TARG_MEM_RADDR (HBUS_BASE+0x00c) #define HBUS_TARG_MEM_WADDR (HBUS_BASE+0x010) #define HBUS_TARG_MEM_WDAT (HBUS_BASE+0x018) #define HBUS_TARG_MEM_RDAT (HBUS_BASE+0x01c) /* * Registers for accessing device's internal peripheral registers * (e.g. SCD, BSM, etc.). First write to address register, * then read from or write to data register to complete the job. * Bit usage for address registers (read or write): * 0-15: register address (offset) within device * 24-25: (# bytes - 1) to read or write (e.g. 3 for dword) */ #define HBUS_TARG_PRPH_WADDR (HBUS_BASE+0x044) #define HBUS_TARG_PRPH_RADDR (HBUS_BASE+0x048) #define HBUS_TARG_PRPH_WDAT (HBUS_BASE+0x04c) #define HBUS_TARG_PRPH_RDAT (HBUS_BASE+0x050) /* * Per-Tx-queue write pointer (index, really!) (3945 and 4965). * Indicates index to next TFD that driver will fill (1 past latest filled). * Bit usage: * 0-7: queue write index (0-255) * 11-8: queue selector (0-15) */ #define HBUS_TARG_WRPTR (HBUS_BASE+0x060) #define HBUS_TARG_MBX_C (HBUS_BASE+0x030) /*=== FH (data Flow Handler) ===*/ #define FH_BASE (0x800) #define FH_RSCSR_CHNL0_WPTR (FH_RSCSR_CHNL0_RBDCB_WPTR_REG) /* RSSR */ #define FH_RSSR_CTRL (FH_RSSR_TABLE+0x000) #define FH_RSSR_STATUS (FH_RSSR_TABLE+0x004) /* TCSR */ #define FH_TCSR(_channel) (FH_TCSR_TABLE+(_channel)*0x20) #define FH_TCSR_CONFIG(_channel) (FH_TCSR(_channel)+0x00) #define FH_TCSR_CREDIT(_channel) (FH_TCSR(_channel)+0x04) #define FH_TCSR_BUFF_STTS(_channel) (FH_TCSR(_channel)+0x08) /* TSSR */ #define FH_TSSR_CBB_BASE (FH_TSSR_TABLE+0x000) #define FH_TSSR_MSG_CONFIG (FH_TSSR_TABLE+0x008) #define FH_TSSR_TX_STATUS (FH_TSSR_TABLE+0x010) #define HBUS_TARG_MBX_C_REG_BIT_CMD_BLOCKED (0x00000004) #define TFD_QUEUE_SIZE_MAX (256) #define IWL_NUM_SCAN_RATES (2) #define IWL_DEFAULT_TX_RETRY 15 #define RX_QUEUE_SIZE 256 #define RX_QUEUE_MASK 255 #define RX_QUEUE_SIZE_LOG 8 #define TFD_TX_CMD_SLOTS 256 #define TFD_CMD_SLOTS 32 #define TFD_MAX_PAYLOAD_SIZE (sizeof(struct iwl4965_cmd) - \ sizeof(struct iwl4965_cmd_meta)) /* * RX related structures and functions */ #define RX_FREE_BUFFERS 64 #define RX_LOW_WATERMARK 8 /* Size of one Rx buffer in host DRAM */ #define IWL_RX_BUF_SIZE (4 * 1024) /* Sizes and addresses for instruction and data memory (SRAM) in * 4965's embedded processor. Driver access is via HBUS_TARG_MEM_* regs. */ #define RTC_INST_LOWER_BOUND (0x000000) #define KDR_RTC_INST_UPPER_BOUND (0x018000) #define RTC_DATA_LOWER_BOUND (0x800000) #define KDR_RTC_DATA_UPPER_BOUND (0x80A000) #define KDR_RTC_INST_SIZE (KDR_RTC_INST_UPPER_BOUND - RTC_INST_LOWER_BOUND) #define KDR_RTC_DATA_SIZE (KDR_RTC_DATA_UPPER_BOUND - RTC_DATA_LOWER_BOUND) #define IWL_MAX_INST_SIZE KDR_RTC_INST_SIZE #define IWL_MAX_DATA_SIZE KDR_RTC_DATA_SIZE /* Size of uCode instruction memory in bootstrap state machine */ #define IWL_MAX_BSM_SIZE BSM_SRAM_SIZE static inline int iwl4965_hw_valid_rtc_data_addr(u32 addr) { return (addr >= RTC_DATA_LOWER_BOUND) && (addr < KDR_RTC_DATA_UPPER_BOUND); } /********************* START TEMPERATURE *************************************/ /** * 4965 temperature calculation. * * The driver must calculate the device temperature before calculating * a txpower setting (amplifier gain is temperature dependent). The * calculation uses 4 measurements, 3 of which (R1, R2, R3) are calibration * values used for the life of the driver, and one of which (R4) is the * real-time temperature indicator. * * uCode provides all 4 values to the driver via the "initialize alive" * notification (see struct iwl4965_init_alive_resp). After the runtime uCode * image loads, uCode updates the R4 value via statistics notifications * (see STATISTICS_NOTIFICATION), which occur after each received beacon * when associated, or can be requested via REPLY_STATISTICS_CMD. * * NOTE: uCode provides the R4 value as a 23-bit signed value. Driver * must sign-extend to 32 bits before applying formula below. * * Formula: * * degrees Kelvin = ((97 * 259 * (R4 - R2) / (R3 - R1)) / 100) + 8 * * NOTE: The basic formula is 259 * (R4-R2) / (R3-R1). The 97/100 is * an additional correction, which should be centered around 0 degrees * Celsius (273 degrees Kelvin). The 8 (3 percent of 273) compensates for * centering the 97/100 correction around 0 degrees K. * * Add 273 to Kelvin value to find degrees Celsius, for comparing current * temperature with factory-measured temperatures when calculating txpower * settings. */ #define TEMPERATURE_CALIB_KELVIN_OFFSET 8 #define TEMPERATURE_CALIB_A_VAL 259 /* Limit range of calculated temperature to be between these Kelvin values */ #define IWL_TX_POWER_TEMPERATURE_MIN (263) #define IWL_TX_POWER_TEMPERATURE_MAX (410) #define IWL_TX_POWER_TEMPERATURE_OUT_OF_RANGE(t) \ (((t) < IWL_TX_POWER_TEMPERATURE_MIN) || \ ((t) > IWL_TX_POWER_TEMPERATURE_MAX)) /********************* END TEMPERATURE ***************************************/ /********************* START TXPOWER *****************************************/ /** * 4965 txpower calculations rely on information from three sources: * * 1) EEPROM * 2) "initialize" alive notification * 3) statistics notifications * * EEPROM data consists of: * * 1) Regulatory information (max txpower and channel usage flags) is provided * separately for each channel that can possibly supported by 4965. * 40 MHz wide (.11n fat) channels are listed separately from 20 MHz * (legacy) channels. * * See struct iwl4965_eeprom_channel for format, and struct iwl4965_eeprom * for locations in EEPROM. * * 2) Factory txpower calibration information is provided separately for * sub-bands of contiguous channels. 2.4GHz has just one sub-band, * but 5 GHz has several sub-bands. * * In addition, per-band (2.4 and 5 Ghz) saturation txpowers are provided. * * See struct iwl4965_eeprom_calib_info (and the tree of structures * contained within it) for format, and struct iwl4965_eeprom for * locations in EEPROM. * * "Initialization alive" notification (see struct iwl4965_init_alive_resp) * consists of: * * 1) Temperature calculation parameters. * * 2) Power supply voltage measurement. * * 3) Tx gain compensation to balance 2 transmitters for MIMO use. * * Statistics notifications deliver: * * 1) Current values for temperature param R4. */ /** * To calculate a txpower setting for a given desired target txpower, channel, * modulation bit rate, and transmitter chain (4965 has 2 transmitters to * support MIMO and transmit diversity), driver must do the following: * * 1) Compare desired txpower vs. (EEPROM) regulatory limit for this channel. * Do not exceed regulatory limit; reduce target txpower if necessary. * * If setting up txpowers for MIMO rates (rate indexes 8-15, 24-31), * 2 transmitters will be used simultaneously; driver must reduce the * regulatory limit by 3 dB (half-power) for each transmitter, so the * combined total output of the 2 transmitters is within regulatory limits. * * * 2) Compare target txpower vs. (EEPROM) saturation txpower *reduced by * backoff for this bit rate*. Do not exceed (saturation - backoff[rate]); * reduce target txpower if necessary. * * Backoff values below are in 1/2 dB units (equivalent to steps in * txpower gain tables): * * OFDM 6 - 36 MBit: 10 steps (5 dB) * OFDM 48 MBit: 15 steps (7.5 dB) * OFDM 54 MBit: 17 steps (8.5 dB) * OFDM 60 MBit: 20 steps (10 dB) * CCK all rates: 10 steps (5 dB) * * Backoff values apply to saturation txpower on a per-transmitter basis; * when using MIMO (2 transmitters), each transmitter uses the same * saturation level provided in EEPROM, and the same backoff values; * no reduction (such as with regulatory txpower limits) is required. * * Saturation and Backoff values apply equally to 20 Mhz (legacy) channel * widths and 40 Mhz (.11n fat) channel widths; there is no separate * factory measurement for fat channels. * * The result of this step is the final target txpower. The rest of * the steps figure out the proper settings for the device to achieve * that target txpower. * * * 3) Determine (EEPROM) calibration subband for the target channel, by * comparing against first and last channels in each subband * (see struct iwl4965_eeprom_calib_subband_info). * * * 4) Linearly interpolate (EEPROM) factory calibration measurement sets, * referencing the 2 factory-measured (sample) channels within the subband. * * Interpolation is based on difference between target channel's frequency * and the sample channels' frequencies. Since channel numbers are based * on frequency (5 MHz between each channel number), this is equivalent * to interpolating based on channel number differences. * * Note that the sample channels may or may not be the channels at the * edges of the subband. The target channel may be "outside" of the * span of the sampled channels. * * Driver may choose the pair (for 2 Tx chains) of measurements (see * struct iwl4965_eeprom_calib_ch_info) for which the actual measured * txpower comes closest to the desired txpower. Usually, though, * the middle set of measurements is closest to the regulatory limits, * and is therefore a good choice for all txpower calculations (this * assumes that high accuracy is needed for maximizing legal txpower, * while lower txpower configurations do not need as much accuracy). * * Driver should interpolate both members of the chosen measurement pair, * i.e. for both Tx chains (radio transmitters), unless the driver knows * that only one of the chains will be used (e.g. only one tx antenna * connected, but this should be unusual). The rate scaling algorithm * switches antennas to find best performance, so both Tx chains will * be used (although only one at a time) even for non-MIMO transmissions. * * Driver should interpolate factory values for temperature, gain table * index, and actual power. The power amplifier detector values are * not used by the driver. * * Sanity check: If the target channel happens to be one of the sample * channels, the results should agree with the sample channel's * measurements! * * * 5) Find difference between desired txpower and (interpolated) * factory-measured txpower. Using (interpolated) factory gain table index * (shown elsewhere) as a starting point, adjust this index lower to * increase txpower, or higher to decrease txpower, until the target * txpower is reached. Each step in the gain table is 1/2 dB. * * For example, if factory measured txpower is 16 dBm, and target txpower * is 13 dBm, add 6 steps to the factory gain index to reduce txpower * by 3 dB. * * * 6) Find difference between current device temperature and (interpolated) * factory-measured temperature for sub-band. Factory values are in * degrees Celsius. To calculate current temperature, see comments for * "4965 temperature calculation". * * If current temperature is higher than factory temperature, driver must * increase gain (lower gain table index), and vice versa. * * Temperature affects gain differently for different channels: * * 2.4 GHz all channels: 3.5 degrees per half-dB step * 5 GHz channels 34-43: 4.5 degrees per half-dB step * 5 GHz channels >= 44: 4.0 degrees per half-dB step * * NOTE: Temperature can increase rapidly when transmitting, especially * with heavy traffic at high txpowers. Driver should update * temperature calculations often under these conditions to * maintain strong txpower in the face of rising temperature. * * * 7) Find difference between current power supply voltage indicator * (from "initialize alive") and factory-measured power supply voltage * indicator (EEPROM). * * If the current voltage is higher (indicator is lower) than factory * voltage, gain should be reduced (gain table index increased) by: * * (eeprom - current) / 7 * * If the current voltage is lower (indicator is higher) than factory * voltage, gain should be increased (gain table index decreased) by: * * 2 * (current - eeprom) / 7 * * If number of index steps in either direction turns out to be > 2, * something is wrong ... just use 0. * * NOTE: Voltage compensation is independent of band/channel. * * NOTE: "Initialize" uCode measures current voltage, which is assumed * to be constant after this initial measurement. Voltage * compensation for txpower (number of steps in gain table) * may be calculated once and used until the next uCode bootload. * * * 8) If setting up txpowers for MIMO rates (rate indexes 8-15, 24-31), * adjust txpower for each transmitter chain, so txpower is balanced * between the two chains. There are 5 pairs of tx_atten[group][chain] * values in "initialize alive", one pair for each of 5 channel ranges: * * Group 0: 5 GHz channel 34-43 * Group 1: 5 GHz channel 44-70 * Group 2: 5 GHz channel 71-124 * Group 3: 5 GHz channel 125-200 * Group 4: 2.4 GHz all channels * * Add the tx_atten[group][chain] value to the index for the target chain. * The values are signed, but are in pairs of 0 and a non-negative number, * so as to reduce gain (if necessary) of the "hotter" channel. This * avoids any need to double-check for regulatory compliance after * this step. * * * 9) If setting up for a CCK rate, lower the gain by adding a CCK compensation * value to the index: * * Hardware rev B: 9 steps (4.5 dB) * Hardware rev C: 5 steps (2.5 dB) * * Hardware rev for 4965 can be determined by reading CSR_HW_REV_WA_REG, * bits [3:2], 1 = B, 2 = C. * * NOTE: This compensation is in addition to any saturation backoff that * might have been applied in an earlier step. * * * 10) Select the gain table, based on band (2.4 vs 5 GHz). * * Limit the adjusted index to stay within the table! * * * 11) Read gain table entries for DSP and radio gain, place into appropriate * location(s) in command (struct iwl4965_txpowertable_cmd). */ /* Limit range of txpower output target to be between these values */ #define IWL_TX_POWER_TARGET_POWER_MIN (0) /* 0 dBm = 1 milliwatt */ #define IWL_TX_POWER_TARGET_POWER_MAX (16) /* 16 dBm */ /** * When MIMO is used (2 transmitters operating simultaneously), driver should * limit each transmitter to deliver a max of 3 dB below the regulatory limit * for the device. That is, use half power for each transmitter, so total * txpower is within regulatory limits. * * The value "6" represents number of steps in gain table to reduce power 3 dB. * Each step is 1/2 dB. */ #define IWL_TX_POWER_MIMO_REGULATORY_COMPENSATION (6) /** * CCK gain compensation. * * When calculating txpowers for CCK, after making sure that the target power * is within regulatory and saturation limits, driver must additionally * back off gain by adding these values to the gain table index. * * Hardware rev for 4965 can be determined by reading CSR_HW_REV_WA_REG, * bits [3:2], 1 = B, 2 = C. */ #define IWL_TX_POWER_CCK_COMPENSATION_B_STEP (9) #define IWL_TX_POWER_CCK_COMPENSATION_C_STEP (5) /* * 4965 power supply voltage compensation for txpower */ #define TX_POWER_IWL_VOLTAGE_CODES_PER_03V (7) /** * Gain tables. * * The following tables contain pair of values for setting txpower, i.e. * gain settings for the output of the device's digital signal processor (DSP), * and for the analog gain structure of the transmitter. * * Each entry in the gain tables represents a step of 1/2 dB. Note that these * are *relative* steps, not indications of absolute output power. Output * power varies with temperature, voltage, and channel frequency, and also * requires consideration of average power (to satisfy regulatory constraints), * and peak power (to avoid distortion of the output signal). * * Each entry contains two values: * 1) DSP gain (or sometimes called DSP attenuation). This is a fine-grained * linear value that multiplies the output of the digital signal processor, * before being sent to the analog radio. * 2) Radio gain. This sets the analog gain of the radio Tx path. * It is a coarser setting, and behaves in a logarithmic (dB) fashion. * * EEPROM contains factory calibration data for txpower. This maps actual * measured txpower levels to gain settings in the "well known" tables * below ("well-known" means here that both factory calibration *and* the * driver work with the same table). * * There are separate tables for 2.4 GHz and 5 GHz bands. The 5 GHz table * has an extension (into negative indexes), in case the driver needs to * boost power setting for high device temperatures (higher than would be * present during factory calibration). A 5 Ghz EEPROM index of "40" * corresponds to the 49th entry in the table used by the driver. */ #define MIN_TX_GAIN_INDEX (0) /* highest gain, lowest idx, 2.4 */ #define MIN_TX_GAIN_INDEX_52GHZ_EXT (-9) /* highest gain, lowest idx, 5 */ /** * 2.4 GHz gain table * * Index Dsp gain Radio gain * 0 110 0x3f (highest gain) * 1 104 0x3f * 2 98 0x3f * 3 110 0x3e * 4 104 0x3e * 5 98 0x3e * 6 110 0x3d * 7 104 0x3d * 8 98 0x3d * 9 110 0x3c * 10 104 0x3c * 11 98 0x3c * 12 110 0x3b * 13 104 0x3b * 14 98 0x3b * 15 110 0x3a * 16 104 0x3a * 17 98 0x3a * 18 110 0x39 * 19 104 0x39 * 20 98 0x39 * 21 110 0x38 * 22 104 0x38 * 23 98 0x38 * 24 110 0x37 * 25 104 0x37 * 26 98 0x37 * 27 110 0x36 * 28 104 0x36 * 29 98 0x36 * 30 110 0x35 * 31 104 0x35 * 32 98 0x35 * 33 110 0x34 * 34 104 0x34 * 35 98 0x34 * 36 110 0x33 * 37 104 0x33 * 38 98 0x33 * 39 110 0x32 * 40 104 0x32 * 41 98 0x32 * 42 110 0x31 * 43 104 0x31 * 44 98 0x31 * 45 110 0x30 * 46 104 0x30 * 47 98 0x30 * 48 110 0x6 * 49 104 0x6 * 50 98 0x6 * 51 110 0x5 * 52 104 0x5 * 53 98 0x5 * 54 110 0x4 * 55 104 0x4 * 56 98 0x4 * 57 110 0x3 * 58 104 0x3 * 59 98 0x3 * 60 110 0x2 * 61 104 0x2 * 62 98 0x2 * 63 110 0x1 * 64 104 0x1 * 65 98 0x1 * 66 110 0x0 * 67 104 0x0 * 68 98 0x0 * 69 97 0 * 70 96 0 * 71 95 0 * 72 94 0 * 73 93 0 * 74 92 0 * 75 91 0 * 76 90 0 * 77 89 0 * 78 88 0 * 79 87 0 * 80 86 0 * 81 85 0 * 82 84 0 * 83 83 0 * 84 82 0 * 85 81 0 * 86 80 0 * 87 79 0 * 88 78 0 * 89 77 0 * 90 76 0 * 91 75 0 * 92 74 0 * 93 73 0 * 94 72 0 * 95 71 0 * 96 70 0 * 97 69 0 * 98 68 0 */ /** * 5 GHz gain table * * Index Dsp gain Radio gain * -9 123 0x3F (highest gain) * -8 117 0x3F * -7 110 0x3F * -6 104 0x3F * -5 98 0x3F * -4 110 0x3E * -3 104 0x3E * -2 98 0x3E * -1 110 0x3D * 0 104 0x3D * 1 98 0x3D * 2 110 0x3C * 3 104 0x3C * 4 98 0x3C * 5 110 0x3B * 6 104 0x3B * 7 98 0x3B * 8 110 0x3A * 9 104 0x3A * 10 98 0x3A * 11 110 0x39 * 12 104 0x39 * 13 98 0x39 * 14 110 0x38 * 15 104 0x38 * 16 98 0x38 * 17 110 0x37 * 18 104 0x37 * 19 98 0x37 * 20 110 0x36 * 21 104 0x36 * 22 98 0x36 * 23 110 0x35 * 24 104 0x35 * 25 98 0x35 * 26 110 0x34 * 27 104 0x34 * 28 98 0x34 * 29 110 0x33 * 30 104 0x33 * 31 98 0x33 * 32 110 0x32 * 33 104 0x32 * 34 98 0x32 * 35 110 0x31 * 36 104 0x31 * 37 98 0x31 * 38 110 0x30 * 39 104 0x30 * 40 98 0x30 * 41 110 0x25 * 42 104 0x25 * 43 98 0x25 * 44 110 0x24 * 45 104 0x24 * 46 98 0x24 * 47 110 0x23 * 48 104 0x23 * 49 98 0x23 * 50 110 0x22 * 51 104 0x18 * 52 98 0x18 * 53 110 0x17 * 54 104 0x17 * 55 98 0x17 * 56 110 0x16 * 57 104 0x16 * 58 98 0x16 * 59 110 0x15 * 60 104 0x15 * 61 98 0x15 * 62 110 0x14 * 63 104 0x14 * 64 98 0x14 * 65 110 0x13 * 66 104 0x13 * 67 98 0x13 * 68 110 0x12 * 69 104 0x08 * 70 98 0x08 * 71 110 0x07 * 72 104 0x07 * 73 98 0x07 * 74 110 0x06 * 75 104 0x06 * 76 98 0x06 * 77 110 0x05 * 78 104 0x05 * 79 98 0x05 * 80 110 0x04 * 81 104 0x04 * 82 98 0x04 * 83 110 0x03 * 84 104 0x03 * 85 98 0x03 * 86 110 0x02 * 87 104 0x02 * 88 98 0x02 * 89 110 0x01 * 90 104 0x01 * 91 98 0x01 * 92 110 0x00 * 93 104 0x00 * 94 98 0x00 * 95 93 0x00 * 96 88 0x00 * 97 83 0x00 * 98 78 0x00 */ /** * Sanity checks and default values for EEPROM regulatory levels. * If EEPROM values fall outside MIN/MAX range, use default values. * * Regulatory limits refer to the maximum average txpower allowed by * regulatory agencies in the geographies in which the device is meant * to be operated. These limits are SKU-specific (i.e. geography-specific), * and channel-specific; each channel has an individual regulatory limit * listed in the EEPROM. * * Units are in half-dBm (i.e. "34" means 17 dBm). */ #define IWL_TX_POWER_DEFAULT_REGULATORY_24 (34) #define IWL_TX_POWER_DEFAULT_REGULATORY_52 (34) #define IWL_TX_POWER_REGULATORY_MIN (0) #define IWL_TX_POWER_REGULATORY_MAX (34) /** * Sanity checks and default values for EEPROM saturation levels. * If EEPROM values fall outside MIN/MAX range, use default values. * * Saturation is the highest level that the output power amplifier can produce * without significant clipping distortion. This is a "peak" power level. * Different types of modulation (i.e. various "rates", and OFDM vs. CCK) * require differing amounts of backoff, relative to their average power output, * in order to avoid clipping distortion. * * Driver must make sure that it is violating neither the saturation limit, * nor the regulatory limit, when calculating Tx power settings for various * rates. * * Units are in half-dBm (i.e. "38" means 19 dBm). */ #define IWL_TX_POWER_DEFAULT_SATURATION_24 (38) #define IWL_TX_POWER_DEFAULT_SATURATION_52 (38) #define IWL_TX_POWER_SATURATION_MIN (20) #define IWL_TX_POWER_SATURATION_MAX (50) /** * Channel groups used for Tx Attenuation calibration (MIMO tx channel balance) * and thermal Txpower calibration. * * When calculating txpower, driver must compensate for current device * temperature; higher temperature requires higher gain. Driver must calculate * current temperature (see "4965 temperature calculation"), then compare vs. * factory calibration temperature in EEPROM; if current temperature is higher * than factory temperature, driver must *increase* gain by proportions shown * in table below. If current temperature is lower than factory, driver must * *decrease* gain. * * Different frequency ranges require different compensation, as shown below. */ /* Group 0, 5.2 GHz ch 34-43: 4.5 degrees per 1/2 dB. */ #define CALIB_IWL_TX_ATTEN_GR1_FCH 34 #define CALIB_IWL_TX_ATTEN_GR1_LCH 43 /* Group 1, 5.3 GHz ch 44-70: 4.0 degrees per 1/2 dB. */ #define CALIB_IWL_TX_ATTEN_GR2_FCH 44 #define CALIB_IWL_TX_ATTEN_GR2_LCH 70 /* Group 2, 5.5 GHz ch 71-124: 4.0 degrees per 1/2 dB. */ #define CALIB_IWL_TX_ATTEN_GR3_FCH 71 #define CALIB_IWL_TX_ATTEN_GR3_LCH 124 /* Group 3, 5.7 GHz ch 125-200: 4.0 degrees per 1/2 dB. */ #define CALIB_IWL_TX_ATTEN_GR4_FCH 125 #define CALIB_IWL_TX_ATTEN_GR4_LCH 200 /* Group 4, 2.4 GHz all channels: 3.5 degrees per 1/2 dB. */ #define CALIB_IWL_TX_ATTEN_GR5_FCH 1 #define CALIB_IWL_TX_ATTEN_GR5_LCH 20 enum { CALIB_CH_GROUP_1 = 0, CALIB_CH_GROUP_2 = 1, CALIB_CH_GROUP_3 = 2, CALIB_CH_GROUP_4 = 3, CALIB_CH_GROUP_5 = 4, CALIB_CH_GROUP_MAX }; /********************* END TXPOWER *****************************************/ /****************************/ /* Flow Handler Definitions */ /****************************/ /** * This I/O area is directly read/writable by driver (e.g. Linux uses writel()) * Addresses are offsets from device's PCI hardware base address. */ #define FH_MEM_LOWER_BOUND (0x1000) #define FH_MEM_UPPER_BOUND (0x1EF0) /** * Keep-Warm (KW) buffer base address. * * Driver must allocate a 4KByte buffer that is used by 4965 for keeping the * host DRAM powered on (via dummy accesses to DRAM) to maintain low-latency * DRAM access when 4965 is Txing or Rxing. The dummy accesses prevent host * from going into a power-savings mode that would cause higher DRAM latency, * and possible data over/under-runs, before all Tx/Rx is complete. * * Driver loads IWL_FH_KW_MEM_ADDR_REG with the physical address (bits 35:4) * of the buffer, which must be 4K aligned. Once this is set up, the 4965 * automatically invokes keep-warm accesses when normal accesses might not * be sufficient to maintain fast DRAM response. * * Bit fields: * 31-0: Keep-warm buffer physical base address [35:4], must be 4K aligned */ #define IWL_FH_KW_MEM_ADDR_REG (FH_MEM_LOWER_BOUND + 0x97C) /** * TFD Circular Buffers Base (CBBC) addresses * * 4965 has 16 base pointer registers, one for each of 16 host-DRAM-resident * circular buffers (CBs/queues) containing Transmit Frame Descriptors (TFDs) * (see struct iwl_tfd_frame). These 16 pointer registers are offset by 0x04 * bytes from one another. Each TFD circular buffer in DRAM must be 256-byte * aligned (address bits 0-7 must be 0). * * Bit fields in each pointer register: * 27-0: TFD CB physical base address [35:8], must be 256-byte aligned */ #define FH_MEM_CBBC_LOWER_BOUND (FH_MEM_LOWER_BOUND + 0x9D0) #define FH_MEM_CBBC_UPPER_BOUND (FH_MEM_LOWER_BOUND + 0xA10) /* Find TFD CB base pointer for given queue (range 0-15). */ #define FH_MEM_CBBC_QUEUE(x) (FH_MEM_CBBC_LOWER_BOUND + (x) * 0x4) /** * Rx SRAM Control and Status Registers (RSCSR) * * These registers provide handshake between driver and 4965 for the Rx queue * (this queue handles *all* command responses, notifications, Rx data, etc. * sent from 4965 uCode to host driver). Unlike Tx, there is only one Rx * queue, and only one Rx DMA/FIFO channel. Also unlike Tx, which can * concatenate up to 20 DRAM buffers to form a Tx frame, each Receive Buffer * Descriptor (RBD) points to only one Rx Buffer (RB); there is a 1:1 * mapping between RBDs and RBs. * * Driver must allocate host DRAM memory for the following, and set the * physical address of each into 4965 registers: * * 1) Receive Buffer Descriptor (RBD) circular buffer (CB), typically with 256 * entries (although any power of 2, up to 4096, is selectable by driver). * Each entry (1 dword) points to a receive buffer (RB) of consistent size * (typically 4K, although 8K or 16K are also selectable by driver). * Driver sets up RB size and number of RBDs in the CB via Rx config * register FH_MEM_RCSR_CHNL0_CONFIG_REG. * * Bit fields within one RBD: * 27-0: Receive Buffer physical address bits [35:8], 256-byte aligned * * Driver sets physical address [35:8] of base of RBD circular buffer * into FH_RSCSR_CHNL0_RBDCB_BASE_REG [27:0]. * * 2) Rx status buffer, 8 bytes, in which 4965 indicates which Rx Buffers * (RBs) have been filled, via a "write pointer", actually the index of * the RB's corresponding RBD within the circular buffer. Driver sets * physical address [35:4] into FH_RSCSR_CHNL0_STTS_WPTR_REG [31:0]. * * Bit fields in lower dword of Rx status buffer (upper dword not used * by driver; see struct iwl4965_shared, val0): * 31-12: Not used by driver * 11- 0: Index of last filled Rx buffer descriptor * (4965 writes, driver reads this value) * * As the driver prepares Receive Buffers (RBs) for 4965 to fill, driver must * enter pointers to these RBs into contiguous RBD circular buffer entries, * and update the 4965's "write" index register, FH_RSCSR_CHNL0_RBDCB_WPTR_REG. * * This "write" index corresponds to the *next* RBD that the driver will make * available, i.e. one RBD past the tail of the ready-to-fill RBDs within * the circular buffer. This value should initially be 0 (before preparing any * RBs), should be 8 after preparing the first 8 RBs (for example), and must * wrap back to 0 at the end of the circular buffer (but don't wrap before * "read" index has advanced past 1! See below). * NOTE: 4965 EXPECTS THE WRITE INDEX TO BE INCREMENTED IN MULTIPLES OF 8. * * As the 4965 fills RBs (referenced from contiguous RBDs within the circular * buffer), it updates the Rx status buffer in host DRAM, 2) described above, * to tell the driver the index of the latest filled RBD. The driver must * read this "read" index from DRAM after receiving an Rx interrupt from 4965. * * The driver must also internally keep track of a third index, which is the * next RBD to process. When receiving an Rx interrupt, driver should process * all filled but unprocessed RBs up to, but not including, the RB * corresponding to the "read" index. For example, if "read" index becomes "1", * driver may process the RB pointed to by RBD 0. Depending on volume of * traffic, there may be many RBs to process. * * If read index == write index, 4965 thinks there is no room to put new data. * Due to this, the maximum number of filled RBs is 255, instead of 256. To * be safe, make sure that there is a gap of at least 2 RBDs between "write" * and "read" indexes; that is, make sure that there are no more than 254 * buffers waiting to be filled. */ #define FH_MEM_RSCSR_LOWER_BOUND (FH_MEM_LOWER_BOUND + 0xBC0) #define FH_MEM_RSCSR_UPPER_BOUND (FH_MEM_LOWER_BOUND + 0xC00) #define FH_MEM_RSCSR_CHNL0 (FH_MEM_RSCSR_LOWER_BOUND) /** * Physical base address of 8-byte Rx Status buffer. * Bit fields: * 31-0: Rx status buffer physical base address [35:4], must 16-byte aligned. */ #define FH_RSCSR_CHNL0_STTS_WPTR_REG (FH_MEM_RSCSR_CHNL0) /** * Physical base address of Rx Buffer Descriptor Circular Buffer. * Bit fields: * 27-0: RBD CD physical base address [35:8], must be 256-byte aligned. */ #define FH_RSCSR_CHNL0_RBDCB_BASE_REG (FH_MEM_RSCSR_CHNL0 + 0x004) /** * Rx write pointer (index, really!). * Bit fields: * 11-0: Index of driver's most recent prepared-to-be-filled RBD, + 1. * NOTE: For 256-entry circular buffer, use only bits [7:0]. */ #define FH_RSCSR_CHNL0_RBDCB_WPTR_REG (FH_MEM_RSCSR_CHNL0 + 0x008) /** * Rx Config/Status Registers (RCSR) * Rx Config Reg for channel 0 (only channel used) * * Driver must initialize FH_MEM_RCSR_CHNL0_CONFIG_REG as follows for * normal operation (see bit fields). * * Clearing FH_MEM_RCSR_CHNL0_CONFIG_REG to 0 turns off Rx DMA. * Driver should poll FH_MEM_RSSR_RX_STATUS_REG for * FH_RSSR_CHNL0_RX_STATUS_CHNL_IDLE (bit 24) before continuing. * * Bit fields: * 31-30: Rx DMA channel enable: '00' off/pause, '01' pause at end of frame, * '10' operate normally * 29-24: reserved * 23-20: # RBDs in circular buffer = 2^value; use "8" for 256 RBDs (normal), * min "5" for 32 RBDs, max "12" for 4096 RBDs. * 19-18: reserved * 17-16: size of each receive buffer; '00' 4K (normal), '01' 8K, * '10' 12K, '11' 16K. * 15-14: reserved * 13-12: IRQ destination; '00' none, '01' host driver (normal operation) * 11- 4: timeout for closing Rx buffer and interrupting host (units 32 usec) * typical value 0x10 (about 1/2 msec) * 3- 0: reserved */ #define FH_MEM_RCSR_LOWER_BOUND (FH_MEM_LOWER_BOUND + 0xC00) #define FH_MEM_RCSR_UPPER_BOUND (FH_MEM_LOWER_BOUND + 0xCC0) #define FH_MEM_RCSR_CHNL0 (FH_MEM_RCSR_LOWER_BOUND) #define FH_MEM_RCSR_CHNL0_CONFIG_REG (FH_MEM_RCSR_CHNL0) #define FH_RCSR_CHNL0_RX_CONFIG_RB_TIMEOUT_MASK (0x00000FF0) /* bit 4-11 */ #define FH_RCSR_CHNL0_RX_CONFIG_IRQ_DEST_MASK (0x00001000) /* bit 12 */ #define FH_RCSR_CHNL0_RX_CONFIG_SINGLE_FRAME_MASK (0x00008000) /* bit 15 */ #define FH_RCSR_CHNL0_RX_CONFIG_RB_SIZE_MASK (0x00030000) /* bits 16-17 */ #define FH_RCSR_CHNL0_RX_CONFIG_RBDBC_SIZE_MASK (0x00F00000) /* bits 20-23 */ #define FH_RCSR_CHNL0_RX_CONFIG_DMA_CHNL_EN_MASK (0xC0000000) /* bits 30-31 */ #define FH_RCSR_RX_CONFIG_RBDCB_SIZE_BITSHIFT (20) #define FH_RCSR_RX_CONFIG_RB_SIZE_BITSHIFT (16) #define FH_RCSR_RX_CONFIG_CHNL_EN_PAUSE_VAL (0x00000000) #define FH_RCSR_RX_CONFIG_CHNL_EN_PAUSE_EOF_VAL (0x40000000) #define FH_RCSR_RX_CONFIG_CHNL_EN_ENABLE_VAL (0x80000000) #define IWL_FH_RCSR_RX_CONFIG_REG_VAL_RB_SIZE_4K (0x00000000) #define FH_RCSR_CHNL0_RX_CONFIG_IRQ_DEST_NO_INT_VAL (0x00000000) #define FH_RCSR_CHNL0_RX_CONFIG_IRQ_DEST_INT_HOST_VAL (0x00001000) /** * Rx Shared Status Registers (RSSR) * * After stopping Rx DMA channel (writing 0 to FH_MEM_RCSR_CHNL0_CONFIG_REG), * driver must poll FH_MEM_RSSR_RX_STATUS_REG until Rx channel is idle. * * Bit fields: * 24: 1 = Channel 0 is idle * * FH_MEM_RSSR_SHARED_CTRL_REG and FH_MEM_RSSR_RX_ENABLE_ERR_IRQ2DRV contain * default values that should not be altered by the driver. */ #define FH_MEM_RSSR_LOWER_BOUND (FH_MEM_LOWER_BOUND + 0xC40) #define FH_MEM_RSSR_UPPER_BOUND (FH_MEM_LOWER_BOUND + 0xD00) #define FH_MEM_RSSR_SHARED_CTRL_REG (FH_MEM_RSSR_LOWER_BOUND) #define FH_MEM_RSSR_RX_STATUS_REG (FH_MEM_RSSR_LOWER_BOUND + 0x004) #define FH_MEM_RSSR_RX_ENABLE_ERR_IRQ2DRV (FH_MEM_RSSR_LOWER_BOUND + 0x008) #define FH_RSSR_CHNL0_RX_STATUS_CHNL_IDLE (0x01000000) /* TCSR */ #define IWL_FH_TCSR_LOWER_BOUND (FH_MEM_LOWER_BOUND + 0xD00) #define IWL_FH_TCSR_UPPER_BOUND (FH_MEM_LOWER_BOUND + 0xE60) #define IWL_FH_TCSR_CHNL_TX_CONFIG_REG(_chnl) \ (IWL_FH_TCSR_LOWER_BOUND + 0x20 * _chnl) /* TSSR Area - Tx shared status registers */ /* TSSR */ #define IWL_FH_TSSR_LOWER_BOUND (FH_MEM_LOWER_BOUND + 0xEA0) #define IWL_FH_TSSR_UPPER_BOUND (FH_MEM_LOWER_BOUND + 0xEC0) #define IWL_FH_TSSR_TX_STATUS_REG (IWL_FH_TSSR_LOWER_BOUND + 0x010) #define IWL_FH_TSSR_TX_STATUS_REG_BIT_BUFS_EMPTY(_chnl) \ ((1 << (_chnl)) << 24) #define IWL_FH_TSSR_TX_STATUS_REG_BIT_NO_PEND_REQ(_chnl) \ ((1 << (_chnl)) << 16) #define IWL_FH_TSSR_TX_STATUS_REG_MSK_CHNL_IDLE(_chnl) \ (IWL_FH_TSSR_TX_STATUS_REG_BIT_BUFS_EMPTY(_chnl) | \ IWL_FH_TSSR_TX_STATUS_REG_BIT_NO_PEND_REQ(_chnl)) #define IWL_FH_TCSR_TX_CONFIG_REG_VAL_DMA_CREDIT_ENABLE_VAL (0x00000008) #define IWL_FH_TCSR_TX_CONFIG_REG_VAL_DMA_CHNL_ENABLE (0x80000000) #define SCD_WIN_SIZE 64 #define SCD_FRAME_LIMIT 64 /* SRAM structures */ #define SCD_CONTEXT_DATA_OFFSET 0x380 #define SCD_TX_STTS_BITMAP_OFFSET 0x400 #define SCD_TRANSLATE_TBL_OFFSET 0x500 #define SCD_CONTEXT_QUEUE_OFFSET(x) (SCD_CONTEXT_DATA_OFFSET + ((x) * 8)) #define SCD_TRANSLATE_TBL_OFFSET_QUEUE(x) \ ((SCD_TRANSLATE_TBL_OFFSET + ((x) * 2)) & 0xfffffffc) #define SCD_TXFACT_REG_TXFIFO_MASK(lo, hi) \ ((1<<(hi))|((1<<(hi))-(1<<(lo)))) #define SCD_QUEUE_STTS_REG_POS_ACTIVE (0) #define SCD_QUEUE_STTS_REG_POS_TXF (1) #define SCD_QUEUE_STTS_REG_POS_WSL (5) #define SCD_QUEUE_STTS_REG_POS_SCD_ACK (8) #define SCD_QUEUE_STTS_REG_POS_SCD_ACT_EN (10) #define SCD_QUEUE_STTS_REG_MSK (0x0007FC00) #define SCD_QUEUE_CTX_REG1_WIN_SIZE_POS (0) #define SCD_QUEUE_CTX_REG1_WIN_SIZE_MSK (0x0000007F) #define SCD_QUEUE_CTX_REG2_FRAME_LIMIT_POS (16) #define SCD_QUEUE_CTX_REG2_FRAME_LIMIT_MSK (0x007F0000) #define CSR_HW_IF_CONFIG_REG_BIT_KEDRON_R (0x00000010) #define CSR_HW_IF_CONFIG_REG_MSK_BOARD_VER (0x00000C00) #define CSR_HW_IF_CONFIG_REG_BIT_MAC_SI (0x00000100) #define CSR_HW_IF_CONFIG_REG_BIT_RADIO_SI (0x00000200) #define CSR_HW_IF_CONFIG_REG_BIT_EEPROM_OWN_SEM (0x00200000) static inline u8 iwl4965_hw_get_rate(__le32 rate_n_flags) { return le32_to_cpu(rate_n_flags) & 0xFF; } static inline u16 iwl4965_hw_get_rate_n_flags(__le32 rate_n_flags) { return le32_to_cpu(rate_n_flags) & 0xFFFF; } static inline __le32 iwl4965_hw_set_rate_n_flags(u8 rate, u16 flags) { return cpu_to_le32(flags|(u16)rate); } struct iwl4965_tfd_frame_data { __le32 tb1_addr; __le32 val1; /* __le32 ptb1_32_35:4; */ #define IWL_tb1_addr_hi_POS 0 #define IWL_tb1_addr_hi_LEN 4 #define IWL_tb1_addr_hi_SYM val1 /* __le32 tb_len1:12; */ #define IWL_tb1_len_POS 4 #define IWL_tb1_len_LEN 12 #define IWL_tb1_len_SYM val1 /* __le32 ptb2_0_15:16; */ #define IWL_tb2_addr_lo16_POS 16 #define IWL_tb2_addr_lo16_LEN 16 #define IWL_tb2_addr_lo16_SYM val1 __le32 val2; /* __le32 ptb2_16_35:20; */ #define IWL_tb2_addr_hi20_POS 0 #define IWL_tb2_addr_hi20_LEN 20 #define IWL_tb2_addr_hi20_SYM val2 /* __le32 tb_len2:12; */ #define IWL_tb2_len_POS 20 #define IWL_tb2_len_LEN 12 #define IWL_tb2_len_SYM val2 } __attribute__ ((packed)); struct iwl4965_tfd_frame { __le32 val0; /* __le32 rsvd1:24; */ /* __le32 num_tbs:5; */ #define IWL_num_tbs_POS 24 #define IWL_num_tbs_LEN 5 #define IWL_num_tbs_SYM val0 /* __le32 rsvd2:1; */ /* __le32 padding:2; */ struct iwl4965_tfd_frame_data pa[10]; __le32 reserved; } __attribute__ ((packed)); #define IWL4965_MAX_WIN_SIZE 64 #define IWL4965_QUEUE_SIZE 256 #define IWL4965_NUM_FIFOS 7 #define IWL_MAX_NUM_QUEUES 16 struct iwl4965_queue_byte_cnt_entry { __le16 val; /* __le16 byte_cnt:12; */ #define IWL_byte_cnt_POS 0 #define IWL_byte_cnt_LEN 12 #define IWL_byte_cnt_SYM val /* __le16 rsvd:4; */ } __attribute__ ((packed)); struct iwl4965_sched_queue_byte_cnt_tbl { struct iwl4965_queue_byte_cnt_entry tfd_offset[IWL4965_QUEUE_SIZE + IWL4965_MAX_WIN_SIZE]; u8 dont_care[1024 - (IWL4965_QUEUE_SIZE + IWL4965_MAX_WIN_SIZE) * sizeof(__le16)]; } __attribute__ ((packed)); /* Base physical address of iwl4965_shared is provided to KDR_SCD_DRAM_BASE_ADDR * and &iwl4965_shared.val0 is provided to FH_RSCSR_CHNL0_STTS_WPTR_REG */ struct iwl4965_shared { struct iwl4965_sched_queue_byte_cnt_tbl queues_byte_cnt_tbls[IWL_MAX_NUM_QUEUES]; __le32 val0; /* __le32 rb_closed_stts_rb_num:12; */ #define IWL_rb_closed_stts_rb_num_POS 0 #define IWL_rb_closed_stts_rb_num_LEN 12 #define IWL_rb_closed_stts_rb_num_SYM val0 /* __le32 rsrv1:4; */ /* __le32 rb_closed_stts_rx_frame_num:12; */ #define IWL_rb_closed_stts_rx_frame_num_POS 16 #define IWL_rb_closed_stts_rx_frame_num_LEN 12 #define IWL_rb_closed_stts_rx_frame_num_SYM val0 /* __le32 rsrv2:4; */ __le32 val1; /* __le32 frame_finished_stts_rb_num:12; */ #define IWL_frame_finished_stts_rb_num_POS 0 #define IWL_frame_finished_stts_rb_num_LEN 12 #define IWL_frame_finished_stts_rb_num_SYM val1 /* __le32 rsrv3:4; */ /* __le32 frame_finished_stts_rx_frame_num:12; */ #define IWL_frame_finished_stts_rx_frame_num_POS 16 #define IWL_frame_finished_stts_rx_frame_num_LEN 12 #define IWL_frame_finished_stts_rx_frame_num_SYM val1 /* __le32 rsrv4:4; */ __le32 padding1; /* so that allocation will be aligned to 16B */ __le32 padding2; } __attribute__ ((packed)); #endif /* __iwl4965_4965_hw_h__ */