Pileus Git - ~andy/linux/blob - drivers/usb/otg/twl4030-usb.c

   1 /*
   2  * twl4030_usb - TWL4030 USB transceiver, talking to OMAP OTG controller
   3  *
   4  * Copyright (C) 2004-2007 Texas Instruments
   5  * Copyright (C) 2008 Nokia Corporation
   6  * Contact: Felipe Balbi <felipe.balbi@nokia.com>
   7  *
   8  * This program is free software; you can redistribute it and/or modify
   9  * it under the terms of the GNU General Public License as published by
  10  * the Free Software Foundation; either version 2 of the License, or
  11  * (at your option) any later version.
  12  *
  13  * This program is distributed in the hope that it will be useful,
  14  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  15  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  16  * GNU General Public License for more details.
  17  *
  18  * You should have received a copy of the GNU General Public License
  19  * along with this program; if not, write to the Free Software
  20  * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
  21  *
  22  * Current status:
  23  *      - HS USB ULPI mode works.
  24  *      - 3-pin mode support may be added in future.
  25  */
  26
  27 #include <linux/module.h>
  28 #include <linux/init.h>
  29 #include <linux/interrupt.h>
  30 #include <linux/platform_device.h>
  31 #include <linux/spinlock.h>
  32 #include <linux/workqueue.h>
  33 #include <linux/io.h>
  34 #include <linux/delay.h>
  35 #include <linux/usb/otg.h>
  36 #include <linux/usb/musb-omap.h>
  37 #include <linux/usb/ulpi.h>
  38 #include <linux/i2c/twl.h>
  39 #include <linux/regulator/consumer.h>
  40 #include <linux/err.h>
  41 #include <linux/slab.h>
  42
  43 /* Register defines */
  44
  45 #define MCPC_CTRL                       0x30
  46 #define MCPC_CTRL_RTSOL                 (1 << 7)
  47 #define MCPC_CTRL_EXTSWR                (1 << 6)
  48 #define MCPC_CTRL_EXTSWC                (1 << 5)
  49 #define MCPC_CTRL_VOICESW               (1 << 4)
  50 #define MCPC_CTRL_OUT64K                (1 << 3)
  51 #define MCPC_CTRL_RTSCTSSW              (1 << 2)
  52 #define MCPC_CTRL_HS_UART               (1 << 0)
  53
  54 #define MCPC_IO_CTRL                    0x33
  55 #define MCPC_IO_CTRL_MICBIASEN          (1 << 5)
  56 #define MCPC_IO_CTRL_CTS_NPU            (1 << 4)
  57 #define MCPC_IO_CTRL_RXD_PU             (1 << 3)
  58 #define MCPC_IO_CTRL_TXDTYP             (1 << 2)
  59 #define MCPC_IO_CTRL_CTSTYP             (1 << 1)
  60 #define MCPC_IO_CTRL_RTSTYP             (1 << 0)
  61
  62 #define MCPC_CTRL2                      0x36
  63 #define MCPC_CTRL2_MCPC_CK_EN           (1 << 0)
  64
  65 #define OTHER_FUNC_CTRL                 0x80
  66 #define OTHER_FUNC_CTRL_BDIS_ACON_EN    (1 << 4)
  67 #define OTHER_FUNC_CTRL_FIVEWIRE_MODE   (1 << 2)
  68
  69 #define OTHER_IFC_CTRL                  0x83
  70 #define OTHER_IFC_CTRL_OE_INT_EN        (1 << 6)
  71 #define OTHER_IFC_CTRL_CEA2011_MODE     (1 << 5)
  72 #define OTHER_IFC_CTRL_FSLSSERIALMODE_4PIN      (1 << 4)
  73 #define OTHER_IFC_CTRL_HIZ_ULPI_60MHZ_OUT       (1 << 3)
  74 #define OTHER_IFC_CTRL_HIZ_ULPI         (1 << 2)
  75 #define OTHER_IFC_CTRL_ALT_INT_REROUTE  (1 << 0)
  76
  77 #define OTHER_INT_EN_RISE               0x86
  78 #define OTHER_INT_EN_FALL               0x89
  79 #define OTHER_INT_STS                   0x8C
  80 #define OTHER_INT_LATCH                 0x8D
  81 #define OTHER_INT_VB_SESS_VLD           (1 << 7)
  82 #define OTHER_INT_DM_HI                 (1 << 6) /* not valid for "latch" reg */
  83 #define OTHER_INT_DP_HI                 (1 << 5) /* not valid for "latch" reg */
  84 #define OTHER_INT_BDIS_ACON             (1 << 3) /* not valid for "fall" regs */
  85 #define OTHER_INT_MANU                  (1 << 1)
  86 #define OTHER_INT_ABNORMAL_STRESS       (1 << 0)
  87
  88 #define ID_STATUS                       0x96
  89 #define ID_RES_FLOAT                    (1 << 4)
  90 #define ID_RES_440K                     (1 << 3)
  91 #define ID_RES_200K                     (1 << 2)
  92 #define ID_RES_102K                     (1 << 1)
  93 #define ID_RES_GND                      (1 << 0)
  94
  95 #define POWER_CTRL                      0xAC
  96 #define POWER_CTRL_OTG_ENAB             (1 << 5)
  97
  98 #define OTHER_IFC_CTRL2                 0xAF
  99 #define OTHER_IFC_CTRL2_ULPI_STP_LOW    (1 << 4)
 100 #define OTHER_IFC_CTRL2_ULPI_TXEN_POL   (1 << 3)
 101 #define OTHER_IFC_CTRL2_ULPI_4PIN_2430  (1 << 2)
 102 #define OTHER_IFC_CTRL2_USB_INT_OUTSEL_MASK     (3 << 0) /* bits 0 and 1 */
 103 #define OTHER_IFC_CTRL2_USB_INT_OUTSEL_INT1N    (0 << 0)
 104 #define OTHER_IFC_CTRL2_USB_INT_OUTSEL_INT2N    (1 << 0)
 105
 106 #define REG_CTRL_EN                     0xB2
 107 #define REG_CTRL_ERROR                  0xB5
 108 #define ULPI_I2C_CONFLICT_INTEN         (1 << 0)
 109
 110 #define OTHER_FUNC_CTRL2                0xB8
 111 #define OTHER_FUNC_CTRL2_VBAT_TIMER_EN  (1 << 0)
 112
 113 /* following registers do not have separate _clr and _set registers */
 114 #define VBUS_DEBOUNCE                   0xC0
 115 #define ID_DEBOUNCE                     0xC1
 116 #define VBAT_TIMER                      0xD3
 117 #define PHY_PWR_CTRL                    0xFD
 118 #define PHY_PWR_PHYPWD                  (1 << 0)
 119 #define PHY_CLK_CTRL                    0xFE
 120 #define PHY_CLK_CTRL_CLOCKGATING_EN     (1 << 2)
 121 #define PHY_CLK_CTRL_CLK32K_EN          (1 << 1)
 122 #define REQ_PHY_DPLL_CLK                (1 << 0)
 123 #define PHY_CLK_CTRL_STS                0xFF
 124 #define PHY_DPLL_CLK                    (1 << 0)
 125
 126 /* In module TWL4030_MODULE_PM_MASTER */
 127 #define STS_HW_CONDITIONS               0x0F
 128
 129 /* In module TWL4030_MODULE_PM_RECEIVER */
 130 #define VUSB_DEDICATED1                 0x7D
 131 #define VUSB_DEDICATED2                 0x7E
 132 #define VUSB1V5_DEV_GRP                 0x71
 133 #define VUSB1V5_TYPE                    0x72
 134 #define VUSB1V5_REMAP                   0x73
 135 #define VUSB1V8_DEV_GRP                 0x74
 136 #define VUSB1V8_TYPE                    0x75
 137 #define VUSB1V8_REMAP                   0x76
 138 #define VUSB3V1_DEV_GRP                 0x77
 139 #define VUSB3V1_TYPE                    0x78
 140 #define VUSB3V1_REMAP                   0x79
 141
 142 /* In module TWL4030_MODULE_INTBR */
 143 #define PMBR1                           0x0D
 144 #define GPIO_USB_4PIN_ULPI_2430C        (3 << 0)
 145
 146 struct twl4030_usb {
 147         struct usb_phy          phy;
 148         struct device           *dev;
 149
 150         /* TWL4030 internal USB regulator supplies */
 151         struct regulator        *usb1v5;
 152         struct regulator        *usb1v8;
 153         struct regulator        *usb3v1;
 154
 155         /* for vbus reporting with irqs disabled */
 156         spinlock_t              lock;
 157
 158         /* pin configuration */
 159         enum twl4030_usb_mode   usb_mode;
 160
 161         int                     irq;
 162         enum omap_musb_vbus_id_status linkstat;
 163         bool                    vbus_supplied;
 164         u8                      asleep;
 165         bool                    irq_enabled;
 166 };
 167
 168 /* internal define on top of container_of */
 169 #define phy_to_twl(x)           container_of((x), struct twl4030_usb, phy)
 170
 171 /*-------------------------------------------------------------------------*/
 172
 173 static int twl4030_i2c_write_u8_verify(struct twl4030_usb *twl,
 174                 u8 module, u8 data, u8 address)
 175 {
 176         u8 check;
 177
 178         if ((twl_i2c_write_u8(module, data, address) >= 0) &&
 179             (twl_i2c_read_u8(module, &check, address) >= 0) &&
 180                                                 (check == data))
 181                 return 0;
 182         dev_dbg(twl->dev, "Write%d[%d,0x%x] wrote %02x but read %02x\n",
 183                         1, module, address, check, data);
 184
 185         /* Failed once: Try again */
 186         if ((twl_i2c_write_u8(module, data, address) >= 0) &&
 187             (twl_i2c_read_u8(module, &check, address) >= 0) &&
 188                                                 (check == data))
 189                 return 0;
 190         dev_dbg(twl->dev, "Write%d[%d,0x%x] wrote %02x but read %02x\n",
 191                         2, module, address, check, data);
 192
 193         /* Failed again: Return error */
 194         return -EBUSY;
 195 }
 196
 197 #define twl4030_usb_write_verify(twl, address, data)    \
 198         twl4030_i2c_write_u8_verify(twl, TWL4030_MODULE_USB, (data), (address))
 199
 200 static inline int twl4030_usb_write(struct twl4030_usb *twl,
 201                 u8 address, u8 data)
 202 {
 203         int ret = 0;
 204
 205         ret = twl_i2c_write_u8(TWL4030_MODULE_USB, data, address);
 206         if (ret < 0)
 207                 dev_dbg(twl->dev,
 208                         "TWL4030:USB:Write[0x%x] Error %d\n", address, ret);
 209         return ret;
 210 }
 211
 212 static inline int twl4030_readb(struct twl4030_usb *twl, u8 module, u8 address)
 213 {
 214         u8 data;
 215         int ret = 0;
 216
 217         ret = twl_i2c_read_u8(module, &data, address);
 218         if (ret >= 0)
 219                 ret = data;
 220         else
 221                 dev_dbg(twl->dev,
 222                         "TWL4030:readb[0x%x,0x%x] Error %d\n",
 223                                         module, address, ret);
 224
 225         return ret;
 226 }
 227
 228 static inline int twl4030_usb_read(struct twl4030_usb *twl, u8 address)
 229 {
 230         return twl4030_readb(twl, TWL4030_MODULE_USB, address);
 231 }
 232
 233 /*-------------------------------------------------------------------------*/
 234
 235 static inline int
 236 twl4030_usb_set_bits(struct twl4030_usb *twl, u8 reg, u8 bits)
 237 {
 238         return twl4030_usb_write(twl, ULPI_SET(reg), bits);
 239 }
 240
 241 static inline int
 242 twl4030_usb_clear_bits(struct twl4030_usb *twl, u8 reg, u8 bits)
 243 {
 244         return twl4030_usb_write(twl, ULPI_CLR(reg), bits);
 245 }
 246
 247 /*-------------------------------------------------------------------------*/
 248
 249 static enum omap_musb_vbus_id_status
 250         twl4030_usb_linkstat(struct twl4030_usb *twl)
 251 {
 252         int     status;
 253         enum omap_musb_vbus_id_status linkstat = OMAP_MUSB_UNKNOWN;
 254
 255         twl->vbus_supplied = false;
 256
 257         /*
 258          * For ID/VBUS sensing, see manual section 15.4.8 ...
 259          * except when using only battery backup power, two
 260          * comparators produce VBUS_PRES and ID_PRES signals,
 261          * which don't match docs elsewhere.  But ... BIT(7)
 262          * and BIT(2) of STS_HW_CONDITIONS, respectively, do
 263          * seem to match up.  If either is true the USB_PRES
 264          * signal is active, the OTG module is activated, and
 265          * its interrupt may be raised (may wake the system).
 266          */
 267         status = twl4030_readb(twl, TWL4030_MODULE_PM_MASTER,
 268                         STS_HW_CONDITIONS);
 269         if (status < 0)
 270                 dev_err(twl->dev, "USB link status err %d\n", status);
 271         else if (status & (BIT(7) | BIT(2))) {
 272                 if (status & (BIT(7)))
 273                         twl->vbus_supplied = true;
 274
 275                 if (status & BIT(2))
 276                         linkstat = OMAP_MUSB_ID_GROUND;
 277                 else
 278                         linkstat = OMAP_MUSB_VBUS_VALID;
 279         } else {
 280                 if (twl->linkstat != OMAP_MUSB_UNKNOWN)
 281                         linkstat = OMAP_MUSB_VBUS_OFF;
 282         }
 283
 284         dev_dbg(twl->dev, "HW_CONDITIONS 0x%02x/%d; link %d\n",
 285                         status, status, linkstat);
 286
 287         /* REVISIT this assumes host and peripheral controllers
 288          * are registered, and that both are active...
 289          */
 290
 291         spin_lock_irq(&twl->lock);
 292         twl->linkstat = linkstat;
 293         spin_unlock_irq(&twl->lock);
 294
 295         return linkstat;
 296 }
 297
 298 static void twl4030_usb_set_mode(struct twl4030_usb *twl, int mode)
 299 {
 300         twl->usb_mode = mode;
 301
 302         switch (mode) {
 303         case T2_USB_MODE_ULPI:
 304                 twl4030_usb_clear_bits(twl, ULPI_IFC_CTRL,
 305                                         ULPI_IFC_CTRL_CARKITMODE);
 306                 twl4030_usb_set_bits(twl, POWER_CTRL, POWER_CTRL_OTG_ENAB);
 307                 twl4030_usb_clear_bits(twl, ULPI_FUNC_CTRL,
 308                                         ULPI_FUNC_CTRL_XCVRSEL_MASK |
 309                                         ULPI_FUNC_CTRL_OPMODE_MASK);
 310                 break;
 311         case -1:
 312                 /* FIXME: power on defaults */
 313                 break;
 314         default:
 315                 dev_err(twl->dev, "unsupported T2 transceiver mode %d\n",
 316                                 mode);
 317                 break;
 318         };
 319 }
 320
 321 static void twl4030_i2c_access(struct twl4030_usb *twl, int on)
 322 {
 323         unsigned long timeout;
 324         int val = twl4030_usb_read(twl, PHY_CLK_CTRL);
 325
 326         if (val >= 0) {
 327                 if (on) {
 328                         /* enable DPLL to access PHY registers over I2C */
 329                         val |= REQ_PHY_DPLL_CLK;
 330                         WARN_ON(twl4030_usb_write_verify(twl, PHY_CLK_CTRL,
 331                                                 (u8)val) < 0);
 332
 333                         timeout = jiffies + HZ;
 334                         while (!(twl4030_usb_read(twl, PHY_CLK_CTRL_STS) &
 335                                                         PHY_DPLL_CLK)
 336                                 && time_before(jiffies, timeout))
 337                                         udelay(10);
 338                         if (!(twl4030_usb_read(twl, PHY_CLK_CTRL_STS) &
 339                                                         PHY_DPLL_CLK))
 340                                 dev_err(twl->dev, "Timeout setting T2 HSUSB "
 341                                                 "PHY DPLL clock\n");
 342                 } else {
 343                         /* let ULPI control the DPLL clock */
 344                         val &= ~REQ_PHY_DPLL_CLK;
 345                         WARN_ON(twl4030_usb_write_verify(twl, PHY_CLK_CTRL,
 346                                                 (u8)val) < 0);
 347                 }
 348         }
 349 }
 350
 351 static void __twl4030_phy_power(struct twl4030_usb *twl, int on)
 352 {
 353         u8 pwr = twl4030_usb_read(twl, PHY_PWR_CTRL);
 354
 355         if (on)
 356                 pwr &= ~PHY_PWR_PHYPWD;
 357         else
 358                 pwr |= PHY_PWR_PHYPWD;
 359
 360         WARN_ON(twl4030_usb_write_verify(twl, PHY_PWR_CTRL, pwr) < 0);
 361 }
 362
 363 static void twl4030_phy_power(struct twl4030_usb *twl, int on)
 364 {
 365         if (on) {
 366                 regulator_enable(twl->usb3v1);
 367                 regulator_enable(twl->usb1v8);
 368                 /*
 369                  * Disabling usb3v1 regulator (= writing 0 to VUSB3V1_DEV_GRP
 370                  * in twl4030) resets the VUSB_DEDICATED2 register. This reset
 371                  * enables VUSB3V1_SLEEP bit that remaps usb3v1 ACTIVE state to
 372                  * SLEEP. We work around this by clearing the bit after usv3v1
 373                  * is re-activated. This ensures that VUSB3V1 is really active.
 374                  */
 375                 twl_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0,
 376                                                         VUSB_DEDICATED2);
 377                 regulator_enable(twl->usb1v5);
 378                 __twl4030_phy_power(twl, 1);
 379                 twl4030_usb_write(twl, PHY_CLK_CTRL,
 380                                   twl4030_usb_read(twl, PHY_CLK_CTRL) |
 381                                         (PHY_CLK_CTRL_CLOCKGATING_EN |
 382                                                 PHY_CLK_CTRL_CLK32K_EN));
 383         } else {
 384                 __twl4030_phy_power(twl, 0);
 385                 regulator_disable(twl->usb1v5);
 386                 regulator_disable(twl->usb1v8);
 387                 regulator_disable(twl->usb3v1);
 388         }
 389 }
 390
 391 static void twl4030_phy_suspend(struct twl4030_usb *twl, int controller_off)
 392 {
 393         if (twl->asleep)
 394                 return;
 395
 396         twl4030_phy_power(twl, 0);
 397         twl->asleep = 1;
 398         dev_dbg(twl->dev, "%s\n", __func__);
 399 }
 400
 401 static void __twl4030_phy_resume(struct twl4030_usb *twl)
 402 {
 403         twl4030_phy_power(twl, 1);
 404         twl4030_i2c_access(twl, 1);
 405         twl4030_usb_set_mode(twl, twl->usb_mode);
 406         if (twl->usb_mode == T2_USB_MODE_ULPI)
 407                 twl4030_i2c_access(twl, 0);
 408 }
 409
 410 static void twl4030_phy_resume(struct twl4030_usb *twl)
 411 {
 412         if (!twl->asleep)
 413                 return;
 414         __twl4030_phy_resume(twl);
 415         twl->asleep = 0;
 416         dev_dbg(twl->dev, "%s\n", __func__);
 417 }
 418
 419 static int twl4030_usb_ldo_init(struct twl4030_usb *twl)
 420 {
 421         /* Enable writing to power configuration registers */
 422         twl_i2c_write_u8(TWL4030_MODULE_PM_MASTER,
 423                         TWL4030_PM_MASTER_KEY_CFG1,
 424                         TWL4030_PM_MASTER_PROTECT_KEY);
 425
 426         twl_i2c_write_u8(TWL4030_MODULE_PM_MASTER,
 427                         TWL4030_PM_MASTER_KEY_CFG2,
 428                         TWL4030_PM_MASTER_PROTECT_KEY);
 429
 430         /* Keep VUSB3V1 LDO in sleep state until VBUS/ID change detected*/
 431         /*twl_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0, VUSB_DEDICATED2);*/
 432
 433         /* input to VUSB3V1 LDO is from VBAT, not VBUS */
 434         twl_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0x14, VUSB_DEDICATED1);
 435
 436         /* Initialize 3.1V regulator */
 437         twl_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0, VUSB3V1_DEV_GRP);
 438
 439         twl->usb3v1 = regulator_get(twl->dev, "usb3v1");
 440         if (IS_ERR(twl->usb3v1))
 441                 return -ENODEV;
 442
 443         twl_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0, VUSB3V1_TYPE);
 444
 445         /* Initialize 1.5V regulator */
 446         twl_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0, VUSB1V5_DEV_GRP);
 447
 448         twl->usb1v5 = regulator_get(twl->dev, "usb1v5");
 449         if (IS_ERR(twl->usb1v5))
 450                 goto fail1;
 451
 452         twl_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0, VUSB1V5_TYPE);
 453
 454         /* Initialize 1.8V regulator */
 455         twl_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0, VUSB1V8_DEV_GRP);
 456
 457         twl->usb1v8 = regulator_get(twl->dev, "usb1v8");
 458         if (IS_ERR(twl->usb1v8))
 459                 goto fail2;
 460
 461         twl_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0, VUSB1V8_TYPE);
 462
 463         /* disable access to power configuration registers */
 464         twl_i2c_write_u8(TWL4030_MODULE_PM_MASTER, 0,
 465                         TWL4030_PM_MASTER_PROTECT_KEY);
 466
 467         return 0;
 468
 469 fail2:
 470         regulator_put(twl->usb1v5);
 471         twl->usb1v5 = NULL;
 472 fail1:
 473         regulator_put(twl->usb3v1);
 474         twl->usb3v1 = NULL;
 475         return -ENODEV;
 476 }
 477
 478 static ssize_t twl4030_usb_vbus_show(struct device *dev,
 479                 struct device_attribute *attr, char *buf)
 480 {
 481         struct twl4030_usb *twl = dev_get_drvdata(dev);
 482         unsigned long flags;
 483         int ret = -EINVAL;
 484
 485         spin_lock_irqsave(&twl->lock, flags);
 486         ret = sprintf(buf, "%s\n",
 487                         twl->vbus_supplied ? "on" : "off");
 488         spin_unlock_irqrestore(&twl->lock, flags);
 489
 490         return ret;
 491 }
 492 static DEVICE_ATTR(vbus, 0444, twl4030_usb_vbus_show, NULL);
 493
 494 static irqreturn_t twl4030_usb_irq(int irq, void *_twl)
 495 {
 496         struct twl4030_usb *twl = _twl;
 497         enum omap_musb_vbus_id_status status;
 498
 499         status = twl4030_usb_linkstat(twl);
 500         if (status > 0) {
 501                 /* FIXME add a set_power() method so that B-devices can
 502                  * configure the charger appropriately.  It's not always
 503                  * correct to consume VBUS power, and how much current to
 504                  * consume is a function of the USB configuration chosen
 505                  * by the host.
 506                  *
 507                  * REVISIT usb_gadget_vbus_connect(...) as needed, ditto
 508                  * its disconnect() sibling, when changing to/from the
 509                  * USB_LINK_VBUS state.  musb_hdrc won't care until it
 510                  * starts to handle softconnect right.
 511                  */
 512                 if (status == OMAP_MUSB_VBUS_OFF ||
 513                                 status == OMAP_MUSB_ID_FLOAT)
 514                         twl4030_phy_suspend(twl, 0);
 515                 else
 516                         twl4030_phy_resume(twl);
 517
 518                 omap_musb_mailbox(twl->linkstat);
 519         }
 520         sysfs_notify(&twl->dev->kobj, NULL, "vbus");
 521
 522         return IRQ_HANDLED;
 523 }
 524
 525 static void twl4030_usb_phy_init(struct twl4030_usb *twl)
 526 {
 527         enum omap_musb_vbus_id_status status;
 528
 529         status = twl4030_usb_linkstat(twl);
 530         if (status > 0) {
 531                 if (status == OMAP_MUSB_VBUS_OFF ||
 532                                 status == OMAP_MUSB_ID_FLOAT) {
 533                         __twl4030_phy_power(twl, 0);
 534                         twl->asleep = 1;
 535                 } else {
 536                         __twl4030_phy_resume(twl);
 537                         twl->asleep = 0;
 538                 }
 539
 540                 omap_musb_mailbox(twl->linkstat);
 541         }
 542         sysfs_notify(&twl->dev->kobj, NULL, "vbus");
 543 }
 544
 545 static int twl4030_set_suspend(struct usb_phy *x, int suspend)
 546 {
 547         struct twl4030_usb *twl = phy_to_twl(x);
 548
 549         if (suspend)
 550                 twl4030_phy_suspend(twl, 1);
 551         else
 552                 twl4030_phy_resume(twl);
 553
 554         return 0;
 555 }
 556
 557 static int twl4030_set_peripheral(struct usb_otg *otg,
 558                                         struct usb_gadget *gadget)
 559 {
 560         if (!otg)
 561                 return -ENODEV;
 562
 563         otg->gadget = gadget;
 564         if (!gadget)
 565                 otg->phy->state = OTG_STATE_UNDEFINED;
 566
 567         return 0;
 568 }
 569
 570 static int twl4030_set_host(struct usb_otg *otg, struct usb_bus *host)
 571 {
 572         if (!otg)
 573                 return -ENODEV;
 574
 575         otg->host = host;
 576         if (!host)
 577                 otg->phy->state = OTG_STATE_UNDEFINED;
 578
 579         return 0;
 580 }
 581
 582 static int __devinit twl4030_usb_probe(struct platform_device *pdev)
 583 {
 584         struct twl4030_usb_data *pdata = pdev->dev.platform_data;
 585         struct twl4030_usb      *twl;
 586         int                     status, err;
 587         struct usb_otg          *otg;
 588         struct device_node      *np = pdev->dev.of_node;
 589
 590         twl = devm_kzalloc(&pdev->dev, sizeof *twl, GFP_KERNEL);
 591         if (!twl)
 592                 return -ENOMEM;
 593
 594         if (np)
 595                 of_property_read_u32(np, "usb_mode",
 596                                 (enum twl4030_usb_mode *)&twl->usb_mode);
 597         else if (pdata)
 598                 twl->usb_mode = pdata->usb_mode;
 599         else {
 600                 dev_err(&pdev->dev, "twl4030 initialized without pdata\n");
 601                 return -EINVAL;
 602         }
 603
 604         otg = devm_kzalloc(&pdev->dev, sizeof *otg, GFP_KERNEL);
 605         if (!otg)
 606                 return -ENOMEM;
 607
 608         twl->dev                = &pdev->dev;
 609         twl->irq                = platform_get_irq(pdev, 0);
 610         twl->vbus_supplied      = false;
 611         twl->asleep             = 1;
 612         twl->linkstat           = OMAP_MUSB_UNKNOWN;
 613
 614         twl->phy.dev            = twl->dev;
 615         twl->phy.label          = "twl4030";
 616         twl->phy.otg            = otg;
 617         twl->phy.set_suspend    = twl4030_set_suspend;
 618
 619         otg->phy                = &twl->phy;
 620         otg->set_host           = twl4030_set_host;
 621         otg->set_peripheral     = twl4030_set_peripheral;
 622
 623         /* init spinlock for workqueue */
 624         spin_lock_init(&twl->lock);
 625
 626         err = twl4030_usb_ldo_init(twl);
 627         if (err) {
 628                 dev_err(&pdev->dev, "ldo init failed\n");
 629                 return err;
 630         }
 631         usb_add_phy(&twl->phy, USB_PHY_TYPE_USB2);
 632
 633         platform_set_drvdata(pdev, twl);
 634         if (device_create_file(&pdev->dev, &dev_attr_vbus))
 635                 dev_warn(&pdev->dev, "could not create sysfs file\n");
 636
 637         /* Our job is to use irqs and status from the power module
 638          * to keep the transceiver disabled when nothing's connected.
 639          *
 640          * FIXME we actually shouldn't start enabling it until the
 641          * USB controller drivers have said they're ready, by calling
 642          * set_host() and/or set_peripheral() ... OTG_capable boards
 643          * need both handles, otherwise just one suffices.
 644          */
 645         twl->irq_enabled = true;
 646         status = request_threaded_irq(twl->irq, NULL, twl4030_usb_irq,
 647                         IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING |
 648                         IRQF_ONESHOT, "twl4030_usb", twl);
 649         if (status < 0) {
 650                 dev_dbg(&pdev->dev, "can't get IRQ %d, err %d\n",
 651                         twl->irq, status);
 652                 return status;
 653         }
 654
 655         /* Power down phy or make it work according to
 656          * current link state.
 657          */
 658         twl4030_usb_phy_init(twl);
 659
 660         dev_info(&pdev->dev, "Initialized TWL4030 USB module\n");
 661         return 0;
 662 }
 663
 664 static int __exit twl4030_usb_remove(struct platform_device *pdev)
 665 {
 666         struct twl4030_usb *twl = platform_get_drvdata(pdev);
 667         int val;
 668
 669         free_irq(twl->irq, twl);
 670         device_remove_file(twl->dev, &dev_attr_vbus);
 671
 672         /* set transceiver mode to power on defaults */
 673         twl4030_usb_set_mode(twl, -1);
 674
 675         /* autogate 60MHz ULPI clock,
 676          * clear dpll clock request for i2c access,
 677          * disable 32KHz
 678          */
 679         val = twl4030_usb_read(twl, PHY_CLK_CTRL);
 680         if (val >= 0) {
 681                 val |= PHY_CLK_CTRL_CLOCKGATING_EN;
 682                 val &= ~(PHY_CLK_CTRL_CLK32K_EN | REQ_PHY_DPLL_CLK);
 683                 twl4030_usb_write(twl, PHY_CLK_CTRL, (u8)val);
 684         }
 685
 686         /* disable complete OTG block */
 687         twl4030_usb_clear_bits(twl, POWER_CTRL, POWER_CTRL_OTG_ENAB);
 688
 689         if (!twl->asleep)
 690                 twl4030_phy_power(twl, 0);
 691         regulator_put(twl->usb1v5);
 692         regulator_put(twl->usb1v8);
 693         regulator_put(twl->usb3v1);
 694
 695         return 0;
 696 }
 697
 698 #ifdef CONFIG_OF
 699 static const struct of_device_id twl4030_usb_id_table[] = {
 700         { .compatible = "ti,twl4030-usb" },
 701         {}
 702 };
 703 MODULE_DEVICE_TABLE(of, twl4030_usb_id_table);
 704 #endif
 705
 706 static struct platform_driver twl4030_usb_driver = {
 707         .probe          = twl4030_usb_probe,
 708         .remove         = __exit_p(twl4030_usb_remove),
 709         .driver         = {
 710                 .name   = "twl4030_usb",
 711                 .owner  = THIS_MODULE,
 712                 .of_match_table = of_match_ptr(twl4030_usb_id_table),
 713         },
 714 };
 715
 716 static int __init twl4030_usb_init(void)
 717 {
 718         return platform_driver_register(&twl4030_usb_driver);
 719 }
 720 subsys_initcall(twl4030_usb_init);
 721
 722 static void __exit twl4030_usb_exit(void)
 723 {
 724         platform_driver_unregister(&twl4030_usb_driver);
 725 }
 726 module_exit(twl4030_usb_exit);
 727
 728 MODULE_ALIAS("platform:twl4030_usb");
 729 MODULE_AUTHOR("Texas Instruments, Inc, Nokia Corporation");
 730 MODULE_DESCRIPTION("TWL4030 USB transceiver driver");
 731 MODULE_LICENSE("GPL");