2 * ehci-omap.c - driver for USBHOST on OMAP3/4 processors
4 * Bus Glue for the EHCI controllers in OMAP3/4
5 * Tested on several OMAP3 boards, and OMAP4 Pandaboard
7 * Copyright (C) 2007-2011 Texas Instruments, Inc.
8 * Author: Vikram Pandita <vikram.pandita@ti.com>
9 * Author: Anand Gadiyar <gadiyar@ti.com>
10 * Author: Keshava Munegowda <keshava_mgowda@ti.com>
12 * Copyright (C) 2009 Nokia Corporation
13 * Contact: Felipe Balbi <felipe.balbi@nokia.com>
15 * Based on "ehci-fsl.c" and "ehci-au1xxx.c" ehci glue layers
17 * This program is free software; you can redistribute it and/or modify
18 * it under the terms of the GNU General Public License as published by
19 * the Free Software Foundation; either version 2 of the License, or
20 * (at your option) any later version.
22 * This program is distributed in the hope that it will be useful,
23 * but WITHOUT ANY WARRANTY; without even the implied warranty of
24 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
25 * GNU General Public License for more details.
27 * You should have received a copy of the GNU General Public License
28 * along with this program; if not, write to the Free Software
29 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
31 * TODO (last updated Feb 27, 2010):
34 * - add suspend/resume
35 * - add HSIC and TLL support
36 * - convert to use hwmod and runtime PM
39 #include <linux/platform_device.h>
40 #include <linux/slab.h>
41 #include <linux/usb/ulpi.h>
43 #include <linux/regulator/consumer.h>
44 #include <linux/pm_runtime.h>
45 #include <linux/gpio.h>
47 /* EHCI Register Set */
48 #define EHCI_INSNREG04 (0xA0)
49 #define EHCI_INSNREG04_DISABLE_UNSUSPEND (1 << 5)
50 #define EHCI_INSNREG05_ULPI (0xA4)
51 #define EHCI_INSNREG05_ULPI_CONTROL_SHIFT 31
52 #define EHCI_INSNREG05_ULPI_PORTSEL_SHIFT 24
53 #define EHCI_INSNREG05_ULPI_OPSEL_SHIFT 22
54 #define EHCI_INSNREG05_ULPI_REGADD_SHIFT 16
55 #define EHCI_INSNREG05_ULPI_EXTREGADD_SHIFT 8
56 #define EHCI_INSNREG05_ULPI_WRDATA_SHIFT 0
58 /*-------------------------------------------------------------------------*/
60 static const struct hc_driver ehci_omap_hc_driver;
63 static inline void ehci_write(void __iomem *base, u32 reg, u32 val)
65 __raw_writel(val, base + reg);
68 static inline u32 ehci_read(void __iomem *base, u32 reg)
70 return __raw_readl(base + reg);
73 static void omap_ehci_soft_phy_reset(struct platform_device *pdev, u8 port)
75 struct usb_hcd *hcd = dev_get_drvdata(&pdev->dev);
76 unsigned long timeout = jiffies + msecs_to_jiffies(1000);
79 reg = ULPI_FUNC_CTRL_RESET
80 /* FUNCTION_CTRL_SET register */
81 | (ULPI_SET(ULPI_FUNC_CTRL) << EHCI_INSNREG05_ULPI_REGADD_SHIFT)
83 | (2 << EHCI_INSNREG05_ULPI_OPSEL_SHIFT)
85 | ((port + 1) << EHCI_INSNREG05_ULPI_PORTSEL_SHIFT)
86 /* start ULPI access*/
87 | (1 << EHCI_INSNREG05_ULPI_CONTROL_SHIFT);
89 ehci_write(hcd->regs, EHCI_INSNREG05_ULPI, reg);
91 /* Wait for ULPI access completion */
92 while ((ehci_read(hcd->regs, EHCI_INSNREG05_ULPI)
93 & (1 << EHCI_INSNREG05_ULPI_CONTROL_SHIFT))) {
96 if (time_after(jiffies, timeout)) {
97 dev_dbg(&pdev->dev, "phy reset operation timed out\n");
103 static void disable_put_regulator(
104 struct ehci_hcd_omap_platform_data *pdata)
108 for (i = 0 ; i < OMAP3_HS_USB_PORTS ; i++) {
109 if (pdata->regulator[i]) {
110 regulator_disable(pdata->regulator[i]);
111 regulator_put(pdata->regulator[i]);
116 /* configure so an HC device and id are always provided */
117 /* always called with process context; sleeping is OK */
120 * ehci_hcd_omap_probe - initialize TI-based HCDs
122 * Allocates basic resources for this USB host controller, and
123 * then invokes the start() method for the HCD associated with it
124 * through the hotplug entry's driver_data.
126 static int ehci_hcd_omap_probe(struct platform_device *pdev)
128 struct device *dev = &pdev->dev;
129 struct ehci_hcd_omap_platform_data *pdata = dev->platform_data;
130 struct resource *res;
133 struct ehci_hcd *omap_ehci;
143 dev_err(dev, "Missing parent device\n");
147 irq = platform_get_irq_byname(pdev, "ehci-irq");
149 dev_err(dev, "EHCI irq failed\n");
153 res = platform_get_resource_byname(pdev,
154 IORESOURCE_MEM, "ehci");
156 dev_err(dev, "UHH EHCI get resource failed\n");
160 regs = ioremap(res->start, resource_size(res));
162 dev_err(dev, "UHH EHCI ioremap failed\n");
166 hcd = usb_create_hcd(&ehci_omap_hc_driver, dev,
169 dev_err(dev, "failed to create hcd with err %d\n", ret);
174 hcd->rsrc_start = res->start;
175 hcd->rsrc_len = resource_size(res);
178 /* get ehci regulator and enable */
179 for (i = 0 ; i < OMAP3_HS_USB_PORTS ; i++) {
180 if (pdata->port_mode[i] != OMAP_EHCI_PORT_MODE_PHY) {
181 pdata->regulator[i] = NULL;
184 snprintf(supply, sizeof(supply), "hsusb%d", i);
185 pdata->regulator[i] = regulator_get(dev, supply);
186 if (IS_ERR(pdata->regulator[i])) {
187 pdata->regulator[i] = NULL;
189 "failed to get ehci port%d regulator\n", i);
191 regulator_enable(pdata->regulator[i]);
195 if (pdata->phy_reset) {
196 if (gpio_is_valid(pdata->reset_gpio_port[0]))
197 gpio_request_one(pdata->reset_gpio_port[0],
198 GPIOF_OUT_INIT_LOW, "USB1 PHY reset");
200 if (gpio_is_valid(pdata->reset_gpio_port[1]))
201 gpio_request_one(pdata->reset_gpio_port[1],
202 GPIOF_OUT_INIT_LOW, "USB2 PHY reset");
204 /* Hold the PHY in RESET for enough time till DIR is high */
208 pm_runtime_enable(dev);
209 pm_runtime_get_sync(dev);
212 * An undocumented "feature" in the OMAP3 EHCI controller,
213 * causes suspended ports to be taken out of suspend when
214 * the USBCMD.Run/Stop bit is cleared (for example when
215 * we do ehci_bus_suspend).
216 * This breaks suspend-resume if the root-hub is allowed
217 * to suspend. Writing 1 to this undocumented register bit
218 * disables this feature and restores normal behavior.
220 ehci_write(regs, EHCI_INSNREG04,
221 EHCI_INSNREG04_DISABLE_UNSUSPEND);
223 /* Soft reset the PHY using PHY reset command over ULPI */
224 if (pdata->port_mode[0] == OMAP_EHCI_PORT_MODE_PHY)
225 omap_ehci_soft_phy_reset(pdev, 0);
226 if (pdata->port_mode[1] == OMAP_EHCI_PORT_MODE_PHY)
227 omap_ehci_soft_phy_reset(pdev, 1);
229 omap_ehci = hcd_to_ehci(hcd);
230 omap_ehci->sbrn = 0x20;
232 /* we know this is the memory we want, no need to ioremap again */
233 omap_ehci->caps = hcd->regs;
234 omap_ehci->regs = hcd->regs
235 + HC_LENGTH(ehci, readl(&omap_ehci->caps->hc_capbase));
237 dbg_hcs_params(omap_ehci, "reset");
238 dbg_hcc_params(omap_ehci, "reset");
240 /* cache this readonly data; minimize chip reads */
241 omap_ehci->hcs_params = readl(&omap_ehci->caps->hcs_params);
243 ehci_reset(omap_ehci);
245 if (pdata->phy_reset) {
246 /* Hold the PHY in RESET for enough time till
247 * PHY is settled and ready
251 if (gpio_is_valid(pdata->reset_gpio_port[0]))
252 gpio_set_value_cansleep(pdata->reset_gpio_port[0], 1);
254 if (gpio_is_valid(pdata->reset_gpio_port[1]))
255 gpio_set_value_cansleep(pdata->reset_gpio_port[1], 1);
258 ret = usb_add_hcd(hcd, irq, IRQF_SHARED);
260 dev_err(dev, "failed to add hcd with err %d\n", ret);
264 /* root ports should always stay powered */
265 ehci_port_power(omap_ehci, 1);
270 disable_put_regulator(pdata);
271 pm_runtime_put_sync(dev);
280 * ehci_hcd_omap_remove - shutdown processing for EHCI HCDs
281 * @pdev: USB Host Controller being removed
283 * Reverses the effect of usb_ehci_hcd_omap_probe(), first invoking
284 * the HCD's stop() method. It is always called from a thread
285 * context, normally "rmmod", "apmd", or something similar.
287 static int ehci_hcd_omap_remove(struct platform_device *pdev)
289 struct device *dev = &pdev->dev;
290 struct usb_hcd *hcd = dev_get_drvdata(dev);
291 struct ehci_hcd_omap_platform_data *pdata = dev->platform_data;
294 disable_put_regulator(dev->platform_data);
297 pm_runtime_put_sync(dev);
298 pm_runtime_disable(dev);
300 if (pdata->phy_reset) {
301 if (gpio_is_valid(pdata->reset_gpio_port[0]))
302 gpio_free(pdata->reset_gpio_port[0]);
304 if (gpio_is_valid(pdata->reset_gpio_port[1]))
305 gpio_free(pdata->reset_gpio_port[1]);
310 static void ehci_hcd_omap_shutdown(struct platform_device *pdev)
312 struct usb_hcd *hcd = dev_get_drvdata(&pdev->dev);
314 if (hcd->driver->shutdown)
315 hcd->driver->shutdown(hcd);
318 static struct platform_driver ehci_hcd_omap_driver = {
319 .probe = ehci_hcd_omap_probe,
320 .remove = ehci_hcd_omap_remove,
321 .shutdown = ehci_hcd_omap_shutdown,
322 /*.suspend = ehci_hcd_omap_suspend, */
323 /*.resume = ehci_hcd_omap_resume, */
329 /*-------------------------------------------------------------------------*/
331 static const struct hc_driver ehci_omap_hc_driver = {
332 .description = hcd_name,
333 .product_desc = "OMAP-EHCI Host Controller",
334 .hcd_priv_size = sizeof(struct ehci_hcd),
337 * generic hardware linkage
340 .flags = HCD_MEMORY | HCD_USB2,
343 * basic lifecycle operations
348 .shutdown = ehci_shutdown,
351 * managing i/o requests and associated device resources
353 .urb_enqueue = ehci_urb_enqueue,
354 .urb_dequeue = ehci_urb_dequeue,
355 .endpoint_disable = ehci_endpoint_disable,
356 .endpoint_reset = ehci_endpoint_reset,
361 .get_frame_number = ehci_get_frame,
366 .hub_status_data = ehci_hub_status_data,
367 .hub_control = ehci_hub_control,
368 .bus_suspend = ehci_bus_suspend,
369 .bus_resume = ehci_bus_resume,
371 .clear_tt_buffer_complete = ehci_clear_tt_buffer_complete,
374 MODULE_ALIAS("platform:omap-ehci");
375 MODULE_AUTHOR("Texas Instruments, Inc.");
376 MODULE_AUTHOR("Felipe Balbi <felipe.balbi@nokia.com>");