Staging: Added Realtek rtl8192u driver to staging

[~andy/linux] / drivers / staging / rtl8192u / r8192U_hw.h

/*
        This is part of rtl8187 OpenSource driver.
        Copyright (C) Andrea Merello 2004-2005  <andreamrl@tiscali.it>
        Released under the terms of GPL (General Public Licence)

        Parts of this driver are based on the GPL part of the
        official Realtek driver.
        Parts of this driver are based on the rtl8180 driver skeleton
        from Patric Schenke & Andres Salomon.
        Parts of this driver are based on the Intel Pro Wireless
        2100 GPL driver.

        We want to tanks the Authors of those projects
        and the Ndiswrapper project Authors.
*/

/* Mariusz Matuszek added full registers definition with Realtek's name */

/* this file contains register definitions for the rtl8187 MAC controller */
#ifndef R8192_HW
#define R8192_HW

typedef enum _VERSION_819xU{
        VERSION_819xU_A, // A-cut
        VERSION_819xU_B, // B-cut
        VERSION_819xU_C,// C-cut
}VERSION_819xU,*PVERSION_819xU;
//added for different RF type
typedef enum _RT_RF_TYPE_DEF
{
        RF_1T2R = 0,
        RF_2T4R,

        RF_819X_MAX_TYPE
}RT_RF_TYPE_DEF;


typedef enum _BaseBand_Config_Type{
        BaseBand_Config_PHY_REG = 0,                    //Radio Path A
        BaseBand_Config_AGC_TAB = 1,                    //Radio Path B
}BaseBand_Config_Type, *PBaseBand_Config_Type;
#if 0
typedef enum _RT_RF_TYPE_819xU{
        RF_TYPE_MIN = 0,
        RF_8225,
        RF_8256,
        RF_8258,
        RF_PSEUDO_11N = 4,
}RT_RF_TYPE_819xU, *PRT_RF_TYPE_819xU;
#endif
#define RTL8187_REQT_READ       0xc0
#define RTL8187_REQT_WRITE      0x40
#define RTL8187_REQ_GET_REGS    0x05
#define RTL8187_REQ_SET_REGS    0x05

#define MAX_TX_URB 5
#define MAX_RX_URB 16

#define R8180_MAX_RETRY 255
//#define MAX_RX_NORMAL_URB 3
//#define MAX_RX_COMMAND_URB 2
#define RX_URB_SIZE 9100

#define BB_ANTATTEN_CHAN14      0x0c
#define BB_ANTENNA_B 0x40

#define BB_HOST_BANG (1<<30)
#define BB_HOST_BANG_EN (1<<2)
#define BB_HOST_BANG_CLK (1<<1)
#define BB_HOST_BANG_RW (1<<3)
#define BB_HOST_BANG_DATA        1

//#if (RTL819X_FPGA_VER & RTL819X_FPGA_VIVI_070920)
#define AFR                     0x010
#define AFR_CardBEn             (1<<0)
#define AFR_CLKRUN_SEL          (1<<1)
#define AFR_FuncRegEn           (1<<2)
#define RTL8190_EEPROM_ID       0x8129
#define EEPROM_VID              0x02
#define EEPROM_PID              0x04
#define EEPROM_NODE_ADDRESS_BYTE_0      0x0C

#define EEPROM_TxPowerDiff      0x1F
#define EEPROM_ThermalMeter     0x20
#define EEPROM_PwDiff           0x21    //0x21
#define EEPROM_CrystalCap       0x22    //0x22

#define EEPROM_TxPwIndex_CCK    0x23    //0x23
#define EEPROM_TxPwIndex_OFDM_24G       0x24    //0x24~0x26
#define EEPROM_TxPwIndex_CCK_V1         0x29    //0x29~0x2B
#define EEPROM_TxPwIndex_OFDM_24G_V1    0x2C    //0x2C~0x2E
#define EEPROM_TxPwIndex_Ver            0x27    //0x27

#define EEPROM_Default_TxPowerDiff              0x0
#define EEPROM_Default_ThermalMeter             0x7
#define EEPROM_Default_PwDiff                   0x4
#define EEPROM_Default_CrystalCap               0x5
#define EEPROM_Default_TxPower                  0x1010
#define EEPROM_Customer_ID                      0x7B    //0x7B:CustomerID
#define EEPROM_ChannelPlan                      0x16    //0x7C
#define EEPROM_IC_VER                           0x7d    //0x7D
#define EEPROM_CRC                              0x7e    //0x7E~0x7F

#define EEPROM_CID_DEFAULT                      0x0
#define EEPROM_CID_CAMEO                                0x1
#define EEPROM_CID_RUNTOP                               0x2
#define EEPROM_CID_Senao                                0x3
#define EEPROM_CID_TOSHIBA                              0x4     // Toshiba setting, Merge by Jacken, 2008/01/31
#define EEPROM_CID_NetCore                              0x5
#define EEPROM_CID_Nettronix                    0x6
#define EEPROM_CID_Pronet                               0x7
#define EEPROM_CID_DLINK                                0x8

#define AC_PARAM_TXOP_LIMIT_OFFSET      16
#define AC_PARAM_ECW_MAX_OFFSET         12
#define AC_PARAM_ECW_MIN_OFFSET         8
#define AC_PARAM_AIFS_OFFSET            0

//#endif
enum _RTL8192Usb_HW {

        PCIF                    = 0x009, // PCI Function Register 0x0009h~0x000bh
#define BB_GLOBAL_RESET_BIT     0x1
        BB_GLOBAL_RESET         = 0x020, // BasebandGlobal Reset Register
        BSSIDR                  = 0x02E, // BSSID Register
        CMDR                    = 0x037, // Command register
#define CR_RST                  0x10
#define CR_RE                   0x08
#define CR_TE                   0x04
#define CR_MulRW                0x01
        SIFS                    = 0x03E, // SIFS register
        TCR                     = 0x040, // Transmit Configuration Register

#define TCR_MXDMA_2048          7
#define TCR_LRL_OFFSET          0
#define TCR_SRL_OFFSET          8
#define TCR_MXDMA_OFFSET        21
#define TCR_SAT                 BIT24           // Enable Rate depedent ack timeout timer
        RCR                     = 0x044, // Receive Configuration Register
#define MAC_FILTER_MASK ((1<<0) | (1<<1) | (1<<2) | (1<<3) | (1<<5) | \
                (1<<12) | (1<<18) | (1<<19) | (1<<20) | (1<<21) | (1<<22) | (1<<23))
#define RX_FIFO_THRESHOLD_MASK ((1<<13) | (1<<14) | (1<<15))
#define RX_FIFO_THRESHOLD_SHIFT 13
#define RX_FIFO_THRESHOLD_128 3
#define RX_FIFO_THRESHOLD_256 4
#define RX_FIFO_THRESHOLD_512 5
#define RX_FIFO_THRESHOLD_1024 6
#define RX_FIFO_THRESHOLD_NONE 7
#define MAX_RX_DMA_MASK ((1<<8) | (1<<9) | (1<<10))
#define RCR_MXDMA_OFFSET        8
#define RCR_FIFO_OFFSET         13
#define RCR_ONLYERLPKT          BIT31                   // Early Receiving based on Packet Size.
#define RCR_ENCS2               BIT30                   // Enable Carrier Sense Detection Method 2
#define RCR_ENCS1               BIT29                   // Enable Carrier Sense Detection Method 1
#define RCR_ENMBID              BIT27                   // Enable Multiple BssId.
#define RCR_ACKTXBW             (BIT24|BIT25)           // TXBW Setting of ACK frames
#define RCR_CBSSID              BIT23                   // Accept BSSID match packet
#define RCR_APWRMGT             BIT22                   // Accept power management packet
#define RCR_ADD3                BIT21                   // Accept address 3 match packet
#define RCR_AMF                 BIT20                   // Accept management type frame
#define RCR_ACF                 BIT19                   // Accept control type frame
#define RCR_ADF                 BIT18                   // Accept data type frame
#define RCR_RXFTH               BIT13                   // Rx FIFO Threshold
#define RCR_AICV                BIT12                   // Accept ICV error packet
#define RCR_ACRC32              BIT5                    // Accept CRC32 error packet
#define RCR_AB                  BIT3                    // Accept broadcast packet
#define RCR_AM                  BIT2                    // Accept multicast packet
#define RCR_APM                 BIT1                    // Accept physical match packet
#define RCR_AAP                 BIT0                    // Accept all unicast packet
        SLOT_TIME               = 0x049, // Slot Time Register
        ACK_TIMEOUT             = 0x04c, // Ack Timeout Register
        PIFS_TIME               = 0x04d, // PIFS time
        USTIME                  = 0x04e, // Microsecond Tuning Register, Sets the microsecond time unit used by MAC clock.
        EDCAPARA_BE             = 0x050, // EDCA Parameter of AC BE
        EDCAPARA_BK             = 0x054, // EDCA Parameter of AC BK
        EDCAPARA_VO             = 0x058, // EDCA Parameter of AC VO
        EDCAPARA_VI             = 0x05C, // EDCA Parameter of AC VI
        RFPC                    = 0x05F, // Rx FIFO Packet Count
        CWRR                    = 0x060, // Contention Window Report Register
        BCN_TCFG                = 0x062, // Beacon Time Configuration
#define BCN_TCFG_CW_SHIFT               8
#define BCN_TCFG_IFS                    0
        BCN_INTERVAL            = 0x070, // Beacon Interval (TU)
        ATIMWND                 = 0x072, // ATIM Window Size (TU)
        BCN_DRV_EARLY_INT       = 0x074, // Driver Early Interrupt Time (TU). Time to send interrupt to notify to change beacon content before TBTT
        BCN_DMATIME             = 0x076, // Beacon DMA and ATIM interrupt time (US). Indicates the time before TBTT to perform beacon queue DMA
        BCN_ERR_THRESH          = 0x078, // Beacon Error Threshold
        RWCAM                   = 0x0A0, //IN 8190 Data Sheet is called CAMcmd
        WCAMI                   = 0x0A4, // Software write CAM input content
        RCAMO                   = 0x0A8, // Software read/write CAM config
        SECR                    = 0x0B0, //Security Configuration Register
#define SCR_TxUseDK             BIT0                    //Force Tx Use Default Key
#define SCR_RxUseDK             BIT1                    //Force Rx Use Default Key
#define SCR_TxEncEnable         BIT2                    //Enable Tx Encryption
#define SCR_RxDecEnable         BIT3                    //Enable Rx Decryption
#define SCR_SKByA2              BIT4                    //Search kEY BY A2
#define SCR_NoSKMC              BIT5                    //No Key Search for Multicast
#define SCR_UseDK               0x01
#define SCR_TxSecEnable         0x02
#define SCR_RxSecEnable         0x04
        TPPoll                  = 0x0fd, // Transmit priority polling register
        PSR                     = 0x0ff, // Page Select Register
#define CPU_CCK_LOOPBACK        0x00030000
#define CPU_GEN_SYSTEM_RESET    0x00000001
#define CPU_GEN_FIRMWARE_RESET  0x00000008
#define CPU_GEN_BOOT_RDY        0x00000010
#define CPU_GEN_FIRM_RDY        0x00000020
#define CPU_GEN_PUT_CODE_OK     0x00000080
#define CPU_GEN_BB_RST          0x00000100
#define CPU_GEN_PWR_STB_CPU     0x00000004
#define CPU_GEN_NO_LOOPBACK_MSK 0xFFF8FFFF              // Set bit18,17,16 to 0. Set bit19
#define CPU_GEN_NO_LOOPBACK_SET 0x00080000              // Set BIT19 to 1

//----------------------------------------------------------------------------
//       8190 CPU General Register              (offset 0x100, 4 byte)
//----------------------------------------------------------------------------
#define CPU_CCK_LOOPBACK        0x00030000
#define CPU_GEN_SYSTEM_RESET    0x00000001
#define CPU_GEN_FIRMWARE_RESET  0x00000008
#define CPU_GEN_BOOT_RDY        0x00000010
#define CPU_GEN_FIRM_RDY        0x00000020
#define CPU_GEN_PUT_CODE_OK     0x00000080
#define CPU_GEN_BB_RST          0x00000100
#define CPU_GEN_PWR_STB_CPU     0x00000004
#define CPU_GEN_NO_LOOPBACK_MSK 0xFFF8FFFF // Set bit18,17,16 to 0. Set bit19
#define CPU_GEN_NO_LOOPBACK_SET 0x00080000 // Set BIT19 to 1
        CPU_GEN                 = 0x100, // CPU Reset Register
        LED1Cfg                 =               0x154,// LED1 Configuration Register
        LED0Cfg                 =               0x155,// LED0 Configuration Register

        AcmAvg                  = 0x170, // ACM Average Period Register
        AcmHwCtrl               = 0x171, // ACM Hardware Control Register
//----------------------------------------------------------------------------
////
////       8190 AcmHwCtrl bits                                    (offset 0x171, 1 byte)
////----------------------------------------------------------------------------
//
#define AcmHw_HwEn              BIT0
#define AcmHw_BeqEn             BIT1
#define AcmHw_ViqEn             BIT2
#define AcmHw_VoqEn             BIT3
#define AcmHw_BeqStatus         BIT4
#define AcmHw_ViqStatus         BIT5
#define AcmHw_VoqStatus         BIT6

        AcmFwCtrl               = 0x172, // ACM Firmware Control Register
        AES_11N_FIX             = 0x173,
        VOAdmTime               = 0x174, // VO Queue Admitted Time Register
        VIAdmTime               = 0x178, // VI Queue Admitted Time Register
        BEAdmTime               = 0x17C, // BE Queue Admitted Time Register
        RQPN1                   = 0x180, // Reserved Queue Page Number , Vo Vi, Be, Bk
        RQPN2                   = 0x184, // Reserved Queue Page Number, HCCA, Cmd, Mgnt, High
        RQPN3                   = 0x188, // Reserved Queue Page Number, Bcn, Public,
//      QPRR                    = 0x1E0, // Queue Page Report per TID
        QPNR                    = 0x1D0, //0x1F0, // Queue Packet Number report per TID
        BQDA                    = 0x200, // Beacon Queue Descriptor Address
        HQDA                    = 0x204, // High Priority Queue Descriptor Address
        CQDA                    = 0x208, // Command Queue Descriptor Address
        MQDA                    = 0x20C, // Management Queue Descriptor Address
        HCCAQDA                 = 0x210, // HCCA Queue Descriptor Address
        VOQDA                   = 0x214, // VO Queue Descriptor Address
        VIQDA                   = 0x218, // VI Queue Descriptor Address
        BEQDA                   = 0x21C, // BE Queue Descriptor Address
        BKQDA                   = 0x220, // BK Queue Descriptor Address
        RCQDA                   = 0x224, // Receive command Queue Descriptor Address
        RDQDA                   = 0x228, // Receive Queue Descriptor Start Address

        MAR0                    = 0x240, // Multicast filter.
        MAR4                    = 0x244,

        CCX_PERIOD              = 0x250, // CCX Measurement Period Register, in unit of TU.
        CLM_RESULT              = 0x251, // CCA Busy fraction register.
        NHM_PERIOD              = 0x252, // NHM Measurement Period register, in unit of TU.

        NHM_THRESHOLD0          = 0x253, // Noise Histogram Meashorement0.
        NHM_THRESHOLD1          = 0x254, // Noise Histogram Meashorement1.
        NHM_THRESHOLD2          = 0x255, // Noise Histogram Meashorement2.
        NHM_THRESHOLD3          = 0x256, // Noise Histogram Meashorement3.
        NHM_THRESHOLD4          = 0x257, // Noise Histogram Meashorement4.
        NHM_THRESHOLD5          = 0x258, // Noise Histogram Meashorement5.
        NHM_THRESHOLD6          = 0x259, // Noise Histogram Meashorement6

        MCTRL                   = 0x25A, // Measurement Control

        NHM_RPI_COUNTER0        = 0x264, // Noise Histogram RPI counter0, the fraction of signal strength < NHM_THRESHOLD0.
        NHM_RPI_COUNTER1        = 0x265, // Noise Histogram RPI counter1, the fraction of signal strength in (NHM_THRESHOLD0, NHM_THRESHOLD1].
        NHM_RPI_COUNTER2        = 0x266, // Noise Histogram RPI counter2, the fraction of signal strength in (NHM_THRESHOLD1, NHM_THRESHOLD2].
        NHM_RPI_COUNTER3        = 0x267, // Noise Histogram RPI counter3, the fraction of signal strength in (NHM_THRESHOLD2, NHM_THRESHOLD3].
        NHM_RPI_COUNTER4        = 0x268, // Noise Histogram RPI counter4, the fraction of signal strength in (NHM_THRESHOLD3, NHM_THRESHOLD4].
        NHM_RPI_COUNTER5        = 0x269, // Noise Histogram RPI counter5, the fraction of signal strength in (NHM_THRESHOLD4, NHM_THRESHOLD5].
        NHM_RPI_COUNTER6        = 0x26A, // Noise Histogram RPI counter6, the fraction of signal strength in (NHM_THRESHOLD5, NHM_THRESHOLD6].
        NHM_RPI_COUNTER7        = 0x26B, // Noise Histogram RPI counter7, the fraction of signal strength in (NHM_THRESHOLD6, NHM_THRESHOLD7].
#define BW_OPMODE_11J                   BIT0
#define BW_OPMODE_5G                    BIT1
#define BW_OPMODE_20MHZ                 BIT2
        BW_OPMODE               = 0x300, // Bandwidth operation mode
        MSR                     = 0x303, // Media Status register
#define MSR_LINK_MASK      ((1<<0)|(1<<1))
#define MSR_LINK_MANAGED   2
#define MSR_LINK_NONE      0
#define MSR_LINK_SHIFT     0
#define MSR_LINK_ADHOC     1
#define MSR_LINK_MASTER    3
#define MSR_LINK_ENEDCA    (1<<4)
        RETRY_LIMIT             = 0x304, // Retry Limit [15:8]-short, [7:0]-long
#define RETRY_LIMIT_SHORT_SHIFT 8
#define RETRY_LIMIT_LONG_SHIFT 0
        TSFR                    = 0x308,
        RRSR                    = 0x310, // Response Rate Set
#define RRSR_RSC_OFFSET                 21
#define RRSR_SHORT_OFFSET                       23
#define RRSR_RSC_DUPLICATE                      0x600000
#define RRSR_RSC_LOWSUBCHNL             0x400000
#define RRSR_RSC_UPSUBCHANL             0x200000
#define RRSR_SHORT                                      0x800000
#define RRSR_1M                                         BIT0
#define RRSR_2M                                         BIT1
#define RRSR_5_5M                                       BIT2
#define RRSR_11M                                        BIT3
#define RRSR_6M                                         BIT4
#define RRSR_9M                                         BIT5
#define RRSR_12M                                        BIT6
#define RRSR_18M                                        BIT7
#define RRSR_24M                                        BIT8
#define RRSR_36M                                        BIT9
#define RRSR_48M                                        BIT10
#define RRSR_54M                                        BIT11
#define RRSR_MCS0                                       BIT12
#define RRSR_MCS1                                       BIT13
#define RRSR_MCS2                                       BIT14
#define RRSR_MCS3                                       BIT15
#define RRSR_MCS4                                       BIT16
#define RRSR_MCS5                                       BIT17
#define RRSR_MCS6                                       BIT18
#define RRSR_MCS7                                       BIT19
#define BRSR_AckShortPmb                        BIT23           // CCK ACK: use Short Preamble or not.
        RATR0                   = 0x320, // Rate Adaptive Table register1
        UFWP                    = 0x318,
        DRIVER_RSSI             = 0x32c,                                        // Driver tell Firmware current RSSI
//----------------------------------------------------------------------------
//       8190 Rate Adaptive Table Register      (offset 0x320, 4 byte)
//----------------------------------------------------------------------------
//CCK
#define RATR_1M                 0x00000001
#define RATR_2M                 0x00000002
#define RATR_55M                0x00000004
#define RATR_11M                0x00000008
//OFDM
#define RATR_6M                 0x00000010
#define RATR_9M                 0x00000020
#define RATR_12M                0x00000040
#define RATR_18M                0x00000080
#define RATR_24M                0x00000100
#define RATR_36M                0x00000200
#define RATR_48M                0x00000400
#define RATR_54M                0x00000800
//MCS 1 Spatial Stream
#define RATR_MCS0               0x00001000
#define RATR_MCS1               0x00002000
#define RATR_MCS2               0x00004000
#define RATR_MCS3               0x00008000
#define RATR_MCS4               0x00010000
#define RATR_MCS5               0x00020000
#define RATR_MCS6               0x00040000
#define RATR_MCS7               0x00080000
//MCS 2 Spatial Stream
#define RATR_MCS8               0x00100000
#define RATR_MCS9               0x00200000
#define RATR_MCS10              0x00400000
#define RATR_MCS11              0x00800000
#define RATR_MCS12              0x01000000
#define RATR_MCS13              0x02000000
#define RATR_MCS14              0x04000000
#define RATR_MCS15              0x08000000
// ALL CCK Rate
#define RATE_ALL_CCK            RATR_1M|RATR_2M|RATR_55M|RATR_11M
#define RATE_ALL_OFDM_AG        RATR_6M|RATR_9M|RATR_12M|RATR_18M|RATR_24M\
                                                        |RATR_36M|RATR_48M|RATR_54M
#define RATE_ALL_OFDM_1SS       RATR_MCS0|RATR_MCS1|RATR_MCS2|RATR_MCS3 | \
                                                        RATR_MCS4|RATR_MCS5|RATR_MCS6|RATR_MCS7
#define RATE_ALL_OFDM_2SS       RATR_MCS8|RATR_MCS9     |RATR_MCS10|RATR_MCS11| \
                                                        RATR_MCS12|RATR_MCS13|RATR_MCS14|RATR_MCS15

        MCS_TXAGC               = 0x340, // MCS AGC
        CCK_TXAGC               = 0x348, // CCK AGC
//      ISR                     = 0x350, // Interrupt Status Register
//      IMR                     = 0x354, // Interrupt Mask Register
//      IMR_POLL                = 0x360,
        MacBlkCtrl              = 0x403, // Mac block on/off control register

        EPROM_CMD               = 0xfe58,
#define Cmd9346CR_9356SEL       (1<<4)
#define EPROM_CMD_RESERVED_MASK (1<<5)
#define EPROM_CMD_OPERATING_MODE_SHIFT 6
#define EPROM_CMD_OPERATING_MODE_MASK ((1<<7)|(1<<6))
#define EPROM_CMD_CONFIG 0x3
#define EPROM_CMD_NORMAL 0
#define EPROM_CMD_LOAD 1
#define EPROM_CMD_PROGRAM 2
#define EPROM_CS_SHIFT 3
#define EPROM_CK_SHIFT 2
#define EPROM_W_SHIFT 1
#define EPROM_R_SHIFT 0
        MAC0                    = 0x000,
        MAC1                    = 0x001,
        MAC2                    = 0x002,
        MAC3                    = 0x003,
        MAC4                    = 0x004,
        MAC5                    = 0x005,

#if 0
/* 0x0006 - 0x0007 - reserved */
        RXFIFOCOUNT             = 0x010,
        TXFIFOCOUNT             = 0x012,
        BQREQ                   = 0x013,
/* 0x0010 - 0x0017 - reserved */
        TSFTR                   = 0x018,
        TLPDA                   = 0x020,
        TNPDA                   = 0x024,
        THPDA                   = 0x028,
        BSSID                   = 0x02E,
        RESP_RATE               = 0x034,
        CMD                     = 0x037,
#define CMD_RST_SHIFT 4
#define CMD_RESERVED_MASK ((1<<1) | (1<<5) | (1<<6) | (1<<7))
#define CMD_RX_ENABLE_SHIFT 3
#define CMD_TX_ENABLE_SHIFT 2
#define CR_RST      ((1<< 4))
#define CR_RE       ((1<< 3))
#define CR_TE       ((1<< 2))
#define CR_MulRW    ((1<< 0))

        INTA_MASK               = 0x03c,
        INTA                    = 0x03e,
#define INTA_TXOVERFLOW (1<<15)
#define INTA_TIMEOUT (1<<14)
#define INTA_BEACONTIMEOUT (1<<13)
#define INTA_ATIM (1<<12)
#define INTA_BEACONDESCERR (1<<11)
#define INTA_BEACONDESCOK (1<<10)
#define INTA_HIPRIORITYDESCERR (1<<9)
#define INTA_HIPRIORITYDESCOK (1<<8)
#define INTA_NORMPRIORITYDESCERR (1<<7)
#define INTA_NORMPRIORITYDESCOK (1<<6)
#define INTA_RXOVERFLOW (1<<5)
#define INTA_RXDESCERR (1<<4)
#define INTA_LOWPRIORITYDESCERR (1<<3)
#define INTA_LOWPRIORITYDESCOK (1<<2)
#define INTA_RXCRCERR (1<<1)
#define INTA_RXOK (1)
        TX_CONF                 = 0x040,
#define TX_CONF_HEADER_AUTOICREMENT_SHIFT 30
#define TX_LOOPBACK_SHIFT 17
#define TX_LOOPBACK_MAC 1
#define TX_LOOPBACK_BASEBAND 2
#define TX_LOOPBACK_NONE 0
#define TX_LOOPBACK_CONTINUE 3
#define TX_LOOPBACK_MASK ((1<<17)|(1<<18))
#define TX_LRLRETRY_SHIFT 0
#define TX_SRLRETRY_SHIFT 8
#define TX_NOICV_SHIFT 19
#define TX_NOCRC_SHIFT 16
#define TCR_DurProcMode  ((1<<30))
#define TCR_DISReqQsize  ((1<<28))
#define TCR_HWVERID_MASK ((1<<27)|(1<<26)|(1<<25))
#define TCR_HWVERID_SHIFT 25
#define TCR_SWPLCPLEN     ((1<<24))
#define TCR_PLCP_LEN TCR_SAT // rtl8180
#define TCR_MXDMA_MASK   ((1<<23)|(1<<22)|(1<<21))
#define TCR_MXDMA_1024 6
#define TCR_MXDMA_2048 7
#define TCR_MXDMA_SHIFT  21
#define TCR_DISCW   ((1<<20))
#define TCR_ICV     ((1<<19))
#define TCR_LBK     ((1<<18)|(1<<17))
#define TCR_LBK1    ((1<<18))
#define TCR_LBK0    ((1<<17))
#define TCR_CRC     ((1<<16))
#define TCR_SRL_MASK   ((1<<15)|(1<<14)|(1<<13)|(1<<12)|(1<<11)|(1<<10)|(1<<9)|(1<<8))
#define TCR_LRL_MASK   ((1<<0)|(1<<1)|(1<<2)|(1<<3)|(1<<4)|(1<<5)|(1<<6)|(1<<7))
#define TCR_PROBE_NOTIMESTAMP_SHIFT 29 //rtl8185
        RX_CONF                 = 0x044,
#define MAC_FILTER_MASK ((1<<0) | (1<<1) | (1<<2) | (1<<3) | (1<<5) | \
(1<<12) | (1<<18) | (1<<19) | (1<<20) | (1<<21) | (1<<22) | (1<<23))
#define RX_CHECK_BSSID_SHIFT 23
#define ACCEPT_PWR_FRAME_SHIFT 22
#define ACCEPT_MNG_FRAME_SHIFT 20
#define ACCEPT_CTL_FRAME_SHIFT 19
#define ACCEPT_DATA_FRAME_SHIFT 18
#define ACCEPT_ICVERR_FRAME_SHIFT 12
#define ACCEPT_CRCERR_FRAME_SHIFT 5
#define ACCEPT_BCAST_FRAME_SHIFT 3
#define ACCEPT_MCAST_FRAME_SHIFT 2
#define ACCEPT_ALLMAC_FRAME_SHIFT 0
#define ACCEPT_NICMAC_FRAME_SHIFT 1
#define RX_FIFO_THRESHOLD_MASK ((1<<13) | (1<<14) | (1<<15))
#define RX_FIFO_THRESHOLD_SHIFT 13
#define RX_FIFO_THRESHOLD_128 3
#define RX_FIFO_THRESHOLD_256 4
#define RX_FIFO_THRESHOLD_512 5
#define RX_FIFO_THRESHOLD_1024 6
#define RX_FIFO_THRESHOLD_NONE 7
#define RX_AUTORESETPHY_SHIFT 28
#define MAX_RX_DMA_MASK ((1<<8) | (1<<9) | (1<<10))
#define MAX_RX_DMA_2048 7
#define MAX_RX_DMA_1024 6
#define MAX_RX_DMA_SHIFT 10
#define RCR_ONLYERLPKT ((1<<31))
#define RCR_CS_SHIFT   29
#define RCR_CS_MASK    ((1<<30) | (1<<29))
#define RCR_ENMARP     ((1<<28))
#define RCR_CBSSID     ((1<<23))
#define RCR_APWRMGT    ((1<<22))
#define RCR_ADD3       ((1<<21))
#define RCR_AMF        ((1<<20))
#define RCR_ACF        ((1<<19))
#define RCR_ADF        ((1<<18))
#define RCR_RXFTH      ((1<<15)|(1<<14)|(1<<13))
#define RCR_RXFTH2     ((1<<15))
#define RCR_RXFTH1     ((1<<14))
#define RCR_RXFTH0     ((1<<13))
#define RCR_AICV       ((1<<12))
#define RCR_MXDMA      ((1<<10)|(1<< 9)|(1<< 8))
#define RCR_MXDMA2     ((1<<10))
#define RCR_MXDMA1     ((1<< 9))
#define RCR_MXDMA0     ((1<< 8))
#define RCR_9356SEL    ((1<< 6))
#define RCR_ACRC32     ((1<< 5))
#define RCR_AB         ((1<< 3))
#define RCR_AM         ((1<< 2))
#define RCR_APM        ((1<< 1))
#define RCR_AAP        ((1<< 0))
        INT_TIMEOUT             = 0x048,
        TX_BEACON_RING_ADDR     = 0x04c,
        EPROM_CMD               = 0x58,
#define EPROM_CMD_RESERVED_MASK ((1<<5)|(1<<4))
#define EPROM_CMD_OPERATING_MODE_SHIFT 6
#define EPROM_CMD_OPERATING_MODE_MASK ((1<<7)|(1<<6))
#define EPROM_CMD_CONFIG 0x3
#define EPROM_CMD_NORMAL 0
#define EPROM_CMD_LOAD 1
#define EPROM_CMD_PROGRAM 2
#define EPROM_CS_SHIFT 3
#define EPROM_CK_SHIFT 2
#define EPROM_W_SHIFT 1
#define EPROM_R_SHIFT 0
        CONFIG0                 = 0x051,
#define CONFIG0_WEP104     ((1<<6))
#define CONFIG0_LEDGPO_En  ((1<<4))
#define CONFIG0_Aux_Status ((1<<3))
#define CONFIG0_GL         ((1<<1)|(1<<0))
#define CONFIG0_GL1        ((1<<1))
#define CONFIG0_GL0        ((1<<0))
        CONFIG1                 = 0x052,
#define CONFIG1_LEDS       ((1<<7)|(1<<6))
#define CONFIG1_LEDS1      ((1<<7))
#define CONFIG1_LEDS0      ((1<<6))
#define CONFIG1_LWACT      ((1<<4))
#define CONFIG1_MEMMAP     ((1<<3))
#define CONFIG1_IOMAP      ((1<<2))
#define CONFIG1_VPD        ((1<<1))
#define CONFIG1_PMEn       ((1<<0))
        CONFIG2                 = 0x053,
#define CONFIG2_LCK        ((1<<7))
#define CONFIG2_ANT        ((1<<6))
#define CONFIG2_DPS        ((1<<3))
#define CONFIG2_PAPE_sign  ((1<<2))
#define CONFIG2_PAPE_time  ((1<<1)|(1<<0))
#define CONFIG2_PAPE_time1 ((1<<1))
#define CONFIG2_PAPE_time0 ((1<<0))
        ANA_PARAM               = 0x054,
        CONFIG3                 = 0x059,
#define CONFIG3_GNTSel     ((1<<7))
#define CONFIG3_PARM_En    ((1<<6))
#define CONFIG3_Magic      ((1<<5))
#define CONFIG3_CardB_En   ((1<<3))
#define CONFIG3_CLKRUN_En  ((1<<2))
#define CONFIG3_FuncRegEn  ((1<<1))
#define CONFIG3_FBtbEn     ((1<<0))
#define CONFIG3_CLKRUN_SHIFT 2
#define CONFIG3_ANAPARAM_W_SHIFT 6
        CONFIG4                 = 0x05a,
#define CONFIG4_VCOPDN     ((1<<7))
#define CONFIG4_PWROFF     ((1<<6))
#define CONFIG4_PWRMGT     ((1<<5))
#define CONFIG4_LWPME      ((1<<4))
#define CONFIG4_LWPTN      ((1<<2))
#define CONFIG4_RFTYPE     ((1<<1)|(1<<0))
#define CONFIG4_RFTYPE1    ((1<<1))
#define CONFIG4_RFTYPE0    ((1<<0))
        TESTR                   = 0x05b,
#define TFPC_AC  0x05C

#define SCR 0x05F
        PGSELECT                = 0x05e,
#define PGSELECT_PG_SHIFT 0
        SECURITY                = 0x05f,
#define SECURITY_WEP_TX_ENABLE_SHIFT 1
#define SECURITY_WEP_RX_ENABLE_SHIFT 0
#define SECURITY_ENCRYP_104 1
#define SECURITY_ENCRYP_SHIFT 4
#define SECURITY_ENCRYP_MASK ((1<<4)|(1<<5))
        ANA_PARAM2              = 0x060,
        BEACON_INTERVAL         = 0x070,
#define BEACON_INTERVAL_MASK ((1<<0)|(1<<1)|(1<<2)|(1<<3)|(1<<4)|(1<<5)| \
(1<<6)|(1<<7)|(1<<8)|(1<<9))
        ATIM_WND                = 0x072,
#define ATIM_WND_MASK      (0x01FF)
        BCN_INTR_ITV            = 0x074,
#define BCN_INTR_ITV_MASK  (0x01FF)
        ATIM_INTR_ITV           = 0x076,
#define ATIM_INTR_ITV_MASK  (0x01FF)
        AckTimeOutReg           = 0x079, //ACK timeout register, in unit of 4 us.
        PHY_ADR                 = 0x07c,
        PHY_READ                = 0x07e,
        RFPinsOutput            = 0x080,
        RFPinsEnable            = 0x082,

//Page 0
        RFPinsSelect            = 0x084,
#define SW_CONTROL_GPIO 0x400
        RFPinsInput             = 0x086,
        RF_PARA                 = 0x088,
        RF_TIMING               = 0x08c,
        GP_ENABLE               = 0x090,
        GPIO                    = 0x091,
        TX_AGC_CTL              = 0x09c,
#define TX_AGC_CTL_PER_PACKET_TXAGC     0x01
#define TX_AGC_CTL_PERPACKET_GAIN_SHIFT 0
#define TX_AGC_CTL_PERPACKET_ANTSEL_SHIFT 1
#define TX_AGC_CTL_FEEDBACK_ANT 2
#define TXAGC_CTL_PER_PACKET_ANT_SEL 0x02
        OFDM_TXAGC              = 0x09e,
        ANTSEL                  = 0x09f,
        WPA_CONFIG              = 0x0b0,
        SIFS                    = 0x0b4,
        DIFS                    = 0x0b5,
        SLOT                    = 0x0b6,
        CW_CONF                 = 0x0bc,
#define CW_CONF_PERPACKET_RETRY_LIMIT 0x02
#define CW_CONF_PERPACKET_CW 0x01
#define CW_CONF_PERPACKET_RETRY_SHIFT 1
#define CW_CONF_PERPACKET_CW_SHIFT 0
        CW_VAL                  = 0x0bd,
        RATE_FALLBACK           = 0x0be,
#define MAX_RESP_RATE_SHIFT 4
#define MIN_RESP_RATE_SHIFT 0
#define RATE_FALLBACK_CTL_ENABLE  0x80
#define RATE_FALLBACK_CTL_AUTO_STEP0 0x00
        ACM_CONTROL             = 0x0BF,      // ACM Control Registe
//----------------------------------------------------------------------------
//       8187B ACM_CONTROL bits                                         (Offset 0xBF, 1 Byte)
//----------------------------------------------------------------------------
#define VOQ_ACM_EN                              (0x01 << 7) //BIT7
#define VIQ_ACM_EN                              (0x01 << 6) //BIT6
#define BEQ_ACM_EN                              (0x01 << 5) //BIT5
#define ACM_HW_EN                               (0x01 << 4) //BIT4
#define TXOPSEL                                 (0x01 << 3) //BIT3
#define VOQ_ACM_CTL                             (0x01 << 2) //BIT2 // Set to 1 when AC_VO used time reaches or exceeds the admitted time
#define VIQ_ACM_CTL                             (0x01 << 1) //BIT1 // Set to 1 when AC_VI used time reaches or exceeds the admitted time
#define BEQ_ACM_CTL                             (0x01 << 0) //BIT0 // Set to 1 when AC_BE used time reaches or exceeds the admitted time
        CONFIG5                 = 0x0D8,
#define CONFIG5_TX_FIFO_OK ((1<<7))
#define CONFIG5_RX_FIFO_OK ((1<<6))
#define CONFIG5_CALON      ((1<<5))
#define CONFIG5_EACPI      ((1<<2))
#define CONFIG5_LANWake    ((1<<1))
#define CONFIG5_PME_STS    ((1<<0))
        TX_DMA_POLLING          = 0x0d9,
#define TX_DMA_POLLING_BEACON_SHIFT 7
#define TX_DMA_POLLING_HIPRIORITY_SHIFT 6
#define TX_DMA_POLLING_NORMPRIORITY_SHIFT 5
#define TX_DMA_POLLING_LOWPRIORITY_SHIFT 4
#define TX_DMA_STOP_BEACON_SHIFT 3
#define TX_DMA_STOP_HIPRIORITY_SHIFT 2
#define TX_DMA_STOP_NORMPRIORITY_SHIFT 1
#define TX_DMA_STOP_LOWPRIORITY_SHIFT 0
        CWR                     = 0x0DC,
        RetryCTR                = 0x0DE,
        INT_MIG                 = 0x0E2,      // Interrupt Migration (0xE2 ~ 0xE3)
        TID_AC_MAP              = 0x0E8,     // TID to AC Mapping Register
        ANA_PARAM3              = 0x0EE,


//page 1
        Wakeup0                 = 0x084,
        Wakeup1                 = 0x08C,
        Wakeup2LD               = 0x094,
        Wakeup2HD               = 0x09C,
        Wakeup3LD               = 0x0A4,
        Wakeup3HD               = 0x0AC,
        Wakeup4LD               = 0x0B4,
        Wakeup4HD               = 0x0BC,
        CRC0                    = 0x0C4,
        CRC1                    = 0x0C6,
        CRC2                    = 0x0C8,
        CRC3                    = 0x0CA,
        CRC4                    = 0x0CC,
/* 0x00CE - 0x00D3 - reserved */

        RFSW_CTRL               = 0x272,   // 0x272-0x273.

//Reg Diff between rtl8187 and rtl8187B
/**************************************************************************/
        BRSR_8187               = 0x02C,
        BRSR_8187B              = 0x034,
#define BRSR_BPLCP  ((1<< 8))
#define BRSR_MBR    ((1<< 1)|(1<< 0))
#define BRSR_MBR_8185 ((1<< 11)|(1<< 10)|(1<< 9)|(1<< 8)|(1<< 7)|(1<< 6)|(1<< 5)|(1<< 4)|(1<< 3)|(1<< 2)|(1<< 1)|(1<< 0))
#define BRSR_MBR0   ((1<< 0))
#define BRSR_MBR1   ((1<< 1))

/**************************************************************************/
        EIFS_8187               = 0x035,
        EIFS_8187B              = 0x02D,

/**************************************************************************/
        FER                     = 0x0F0,
        FEMR                    = 0x0F4,
        FPSR                    = 0x0F8,
        FFER                    = 0x0FC,

        AC_VO_PARAM             = 0x0F0,      // AC_VO Parameters Record
        AC_VI_PARAM             = 0x0F4,      // AC_VI Parameters Record
        AC_BE_PARAM             = 0x0F8,      // AC_BE Parameters Record
        AC_BK_PARAM             = 0x0FC,      // AC_BK Parameters Record
        TALLY_SEL               = 0x0fc,
//----------------------------------------------------------------------------
//       8187B AC_XX_PARAM bits
//----------------------------------------------------------------------------
#define AC_PARAM_TXOP_LIMIT_OFFSET              16
#define AC_PARAM_ECW_MAX_OFFSET                 12
#define AC_PARAM_ECW_MIN_OFFSET                 8
#define AC_PARAM_AIFS_OFFSET                    0

#endif
};
//----------------------------------------------------------------------------
//       818xB AnaParm & AnaParm2 Register
//----------------------------------------------------------------------------
//#define ANAPARM_ASIC_ON    0x45090658
//#define ANAPARM2_ASIC_ON   0x727f3f52
#define GPI 0x108
#define GPO 0x109
#define GPE 0x10a
#endif