[SCSI] move iscsi to a better place in Kconfig

[~andy/linux] / drivers / scsi / Kconfig

menu "SCSI device support"

config RAID_ATTRS
        tristate "RAID Transport Class"
        default n
        ---help---
          Provides RAID

config SCSI
        tristate "SCSI device support"
        ---help---
          If you want to use a SCSI hard disk, SCSI tape drive, SCSI CD-ROM or
          any other SCSI device under Linux, say Y and make sure that you know
          the name of your SCSI host adapter (the card inside your computer
          that "speaks" the SCSI protocol, also called SCSI controller),
          because you will be asked for it.

          You also need to say Y here if you have a device which speaks
          the SCSI protocol.  Examples of this include the parallel port
          version of the IOMEGA ZIP drive, USB storage devices, Fibre
          Channel, FireWire storage and the IDE-SCSI emulation driver.

          To compile this driver as a module, choose M here and read
          <file:Documentation/scsi/scsi.txt>.
          The module will be called scsi_mod.

          However, do not compile this as a module if your root file system
          (the one containing the directory /) is located on a SCSI device.

config SCSI_PROC_FS
        bool "legacy /proc/scsi/ support"
        depends on SCSI && PROC_FS
        default y
        ---help---
          This option enables support for the various files in
          /proc/scsi.  In Linux 2.6 this has been superceeded by
          files in sysfs but many legacy applications rely on this.

          If unusure say Y.

comment "SCSI support type (disk, tape, CD-ROM)"
        depends on SCSI

config BLK_DEV_SD
        tristate "SCSI disk support"
        depends on SCSI
        ---help---
          If you want to use SCSI hard disks, Fibre Channel disks,
          USB storage or the SCSI or parallel port version of
          the IOMEGA ZIP drive, say Y and read the SCSI-HOWTO,
          the Disk-HOWTO and the Multi-Disk-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>. This is NOT for SCSI
          CD-ROMs.

          To compile this driver as a module, choose M here and read
          <file:Documentation/scsi/scsi.txt>.
          The module will be called sd_mod.

          Do not compile this driver as a module if your root file system
          (the one containing the directory /) is located on a SCSI disk.
          In this case, do not compile the driver for your SCSI host adapter
          (below) as a module either.

config CHR_DEV_ST
        tristate "SCSI tape support"
        depends on SCSI
        ---help---
          If you want to use a SCSI tape drive under Linux, say Y and read the
          SCSI-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>, and
          <file:Documentation/scsi/st.txt> in the kernel source.  This is NOT
          for SCSI CD-ROMs.

          To compile this driver as a module, choose M here and read
          <file:Documentation/scsi/scsi.txt>. The module will be called st.

config CHR_DEV_OSST
        tristate "SCSI OnStream SC-x0 tape support"
        depends on SCSI
        ---help---
          The OnStream SC-x0 SCSI tape drives can not be driven by the
          standard st driver, but instead need this special osst driver and
          use the  /dev/osstX char device nodes (major 206).  Via usb-storage
          and ide-scsi, you may be able to drive the USB-x0 and DI-x0 drives
          as well.  Note that there is also a second generation of OnStream
          tape drives (ADR-x0) that supports the standard SCSI-2 commands for
          tapes (QIC-157) and can be driven by the standard driver st.
          For more information, you may have a look at the SCSI-HOWTO
          <http://www.tldp.org/docs.html#howto>  and
          <file:Documentation/scsi/osst.txt>  in the kernel source.
          More info on the OnStream driver may be found on
          <http://linux1.onstream.nl/test/>
          Please also have a look at the standard st docu, as most of it
          applies to osst as well.

          To compile this driver as a module, choose M here and read
          <file:Documentation/scsi/scsi.txt>. The module will be called osst.

config BLK_DEV_SR
        tristate "SCSI CDROM support"
        depends on SCSI
        ---help---
          If you want to use a SCSI or FireWire CD-ROM under Linux,
          say Y and read the SCSI-HOWTO and the CDROM-HOWTO at
          <http://www.tldp.org/docs.html#howto>. Also make sure to say
          Y or M to "ISO 9660 CD-ROM file system support" later.

          To compile this driver as a module, choose M here and read
          <file:Documentation/scsi/scsi.txt>.
          The module will be called sr_mod.

config BLK_DEV_SR_VENDOR
        bool "Enable vendor-specific extensions (for SCSI CDROM)"
        depends on BLK_DEV_SR
        help
          This enables the usage of vendor specific SCSI commands. This is
          required to support multisession CDs with old NEC/TOSHIBA cdrom
          drives (and HP Writers). If you have such a drive and get the first
          session only, try saying Y here; everybody else says N.

config CHR_DEV_SG
        tristate "SCSI generic support"
        depends on SCSI
        ---help---
          If you want to use SCSI scanners, synthesizers or CD-writers or just
          about anything having "SCSI" in its name other than hard disks,
          CD-ROMs or tapes, say Y here. These won't be supported by the kernel
          directly, so you need some additional software which knows how to
          talk to these devices using the SCSI protocol:

          For scanners, look at SANE (<http://www.mostang.com/sane/>). For CD
          writer software look at Cdrtools
          (<http://www.fokus.gmd.de/research/cc/glone/employees/joerg.schilling/private/cdrecord.html>)
          and for burning a "disk at once": CDRDAO
          (<http://cdrdao.sourceforge.net/>). Cdparanoia is a high
          quality digital reader of audio CDs (<http://www.xiph.org/paranoia/>).
          For other devices, it's possible that you'll have to write the
          driver software yourself. Please read the file
          <file:Documentation/scsi/scsi-generic.txt> for more information.

          To compile this driver as a module, choose M here and read
          <file:Documentation/scsi/scsi.txt>. The module will be called sg.

          If unsure, say N.

config CHR_DEV_SCH
        tristate "SCSI media changer support"
        depends on SCSI
        ---help---
          This is a driver for SCSI media changers.  Most common devices are
          tape libraries and MOD/CDROM jukeboxes.  *Real* jukeboxes, you
          don't need this for those tiny 6-slot cdrom changers.  Media
          changers are listed as "Type: Medium Changer" in /proc/scsi/scsi.
          If you have such hardware and want to use it with linux, say Y
          here.  Check <file:Documentation/scsi-changer.txt> for details.
        
          If you want to compile this as a module ( = code which can be
          inserted in and removed from the running kernel whenever you want),
          say M here and read <file:Documentation/modules.txt> and
          <file:Documentation/scsi.txt>. The module will be called ch.o.
          If unsure, say N.
        

comment "Some SCSI devices (e.g. CD jukebox) support multiple LUNs"
        depends on SCSI

config SCSI_MULTI_LUN
        bool "Probe all LUNs on each SCSI device"
        depends on SCSI
        help
          If you have a SCSI device that supports more than one LUN (Logical
          Unit Number), e.g. a CD jukebox, and only one LUN is detected, you
          can say Y here to force the SCSI driver to probe for multiple LUNs.
          A SCSI device with multiple LUNs acts logically like multiple SCSI
          devices. The vast majority of SCSI devices have only one LUN, and
          so most people can say N here. The max_luns boot/module parameter 
          allows to override this setting.

config SCSI_CONSTANTS
        bool "Verbose SCSI error reporting (kernel size +=12K)"
        depends on SCSI
        help
          The error messages regarding your SCSI hardware will be easier to
          understand if you say Y here; it will enlarge your kernel by about
          12 KB. If in doubt, say Y.

config SCSI_LOGGING
        bool "SCSI logging facility"
        depends on SCSI
        ---help---
          This turns on a logging facility that can be used to debug a number
          of SCSI related problems.

          If you say Y here, no logging output will appear by default, but you
          can enable logging by saying Y to "/proc file system support" and
          "Sysctl support" below and executing the command

          echo "scsi log token [level]" > /proc/scsi/scsi

          at boot time after the /proc file system has been mounted.

          There are a number of things that can be used for 'token' (you can
          find them in the source: <file:drivers/scsi/scsi.c>), and this
          allows you to select the types of information you want, and the
          level allows you to select the level of verbosity.

          If you say N here, it may be harder to track down some types of SCSI
          problems. If you say Y here your kernel will be somewhat larger, but
          there should be no noticeable performance impact as long as you have
          logging turned off.

menu "SCSI Transport Attributes"
        depends on SCSI

config SCSI_SPI_ATTRS
        tristate "Parallel SCSI (SPI) Transport Attributes"
        depends on SCSI
        help
          If you wish to export transport-specific information about
          each attached SCSI device to sysfs, say Y.  Otherwise, say N.

config SCSI_FC_ATTRS
        tristate "FiberChannel Transport Attributes"
        depends on SCSI
        help
          If you wish to export transport-specific information about
          each attached FiberChannel device to sysfs, say Y.
          Otherwise, say N.

config SCSI_ISCSI_ATTRS
        tristate "iSCSI Transport Attributes"
        depends on SCSI && NET
        help
          If you wish to export transport-specific information about
          each attached iSCSI device to sysfs, say Y.
          Otherwise, say N.

endmenu

menu "SCSI low-level drivers"
        depends on SCSI!=n

config ISCSI_TCP
        tristate "iSCSI Initiator over TCP/IP"
        depends on SCSI && INET
        select CRYPTO
        select CRYPTO_MD5
        select CRYPTO_CRC32C
        select SCSI_ISCSI_ATTRS
        help
         The iSCSI Driver provides a host with the ability to access storage
         through an IP network. The driver uses the iSCSI protocol to transport
         SCSI requests and responses over a TCP/IP network between the host
         (the "initiator") and "targets".  Architecturally, the iSCSI driver
         combines with the host's TCP/IP stack, network drivers, and Network
         Interface Card (NIC) to provide the same functions as a SCSI or a
         Fibre Channel (FC) adapter driver with a Host Bus Adapter (HBA).

         To compile this driver as a module, choose M here: the
         module will be called iscsi_tcp.

         The userspace component needed to initialize the driver, documentation,
         and sample configuration files can be found here:

         http://linux-iscsi.sf.net

config SGIWD93_SCSI
        tristate "SGI WD93C93 SCSI Driver"
        depends on SGI_IP22 && SCSI
        help
          If you have a Western Digital WD93 SCSI controller on
          an SGI MIPS system, say Y.  Otherwise, say N.

config SCSI_DECNCR
        tristate "DEC NCR53C94 Scsi Driver"
        depends on MACH_DECSTATION && SCSI && TC
        help
          Say Y here to support the NCR53C94 SCSI controller chips on IOASIC
          based TURBOchannel DECstations and TURBOchannel PMAZ-A cards.

config SCSI_DECSII
        tristate "DEC SII Scsi Driver"
        depends on MACH_DECSTATION && SCSI && 32BIT

config BLK_DEV_3W_XXXX_RAID
        tristate "3ware 5/6/7/8xxx ATA-RAID support"
        depends on PCI && SCSI
        help
          3ware is the only hardware ATA-Raid product in Linux to date.
          This card is 2,4, or 8 channel master mode support only.
          SCSI support required!!!

          <http://www.3ware.com/>

          Please read the comments at the top of
          <file:drivers/scsi/3w-xxxx.c>.

config SCSI_3W_9XXX
        tristate "3ware 9xxx SATA-RAID support"
        depends on PCI && SCSI
        help
          This driver supports the 9000 series 3ware SATA-RAID cards.

          <http://www.amcc.com>

          Please read the comments at the top of
          <file:drivers/scsi/3w-9xxx.c>.

config SCSI_7000FASST
        tristate "7000FASST SCSI support"
        depends on ISA && SCSI && ISA_DMA_API
        help
          This driver supports the Western Digital 7000 SCSI host adapter
          family.  Some information is in the source:
          <file:drivers/scsi/wd7000.c>.

          To compile this driver as a module, choose M here: the
          module will be called wd7000.

config SCSI_ACARD
        tristate "ACARD SCSI support"
        depends on PCI && SCSI
        help
          This driver supports the ACARD SCSI host adapter.
          Support Chip <ATP870 ATP876 ATP880 ATP885>
          To compile this driver as a module, choose M here: the
          module will be called atp870u.

config SCSI_AHA152X
        tristate "Adaptec AHA152X/2825 support"
        depends on ISA && SCSI && !64BIT
        ---help---
          This is a driver for the AHA-1510, AHA-1520, AHA-1522, and AHA-2825
          SCSI host adapters. It also works for the AVA-1505, but the IRQ etc.
          must be manually specified in this case.

          It is explained in section 3.3 of the SCSI-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>. You might also want to
          read the file <file:Documentation/scsi/aha152x.txt>.

          To compile this driver as a module, choose M here: the
          module will be called aha152x.

config SCSI_AHA1542
        tristate "Adaptec AHA1542 support"
        depends on ISA && SCSI && ISA_DMA_API
        ---help---
          This is support for a SCSI host adapter.  It is explained in section
          3.4 of the SCSI-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>.  Note that Trantor was
          purchased by Adaptec, and some former Trantor products are being
          sold under the Adaptec name.  If it doesn't work out of the box, you
          may have to change some settings in <file:drivers/scsi/aha1542.h>.

          To compile this driver as a module, choose M here: the
          module will be called aha1542.

config SCSI_AHA1740
        tristate "Adaptec AHA1740 support"
        depends on EISA && SCSI
        ---help---
          This is support for a SCSI host adapter.  It is explained in section
          3.5 of the SCSI-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>.  If it doesn't work out
          of the box, you may have to change some settings in
          <file:drivers/scsi/aha1740.h>.

          To compile this driver as a module, choose M here: the
          module will be called aha1740.

config SCSI_AACRAID
        tristate "Adaptec AACRAID support"
        depends on SCSI && PCI

source "drivers/scsi/aic7xxx/Kconfig.aic7xxx"

config SCSI_AIC7XXX_OLD
        tristate "Adaptec AIC7xxx support (old driver)"
        depends on (ISA || EISA || PCI ) && SCSI
        help
          WARNING This driver is an older aic7xxx driver and is no longer
          under active development.  Adaptec, Inc. is writing a new driver to
          take the place of this one, and it is recommended that whenever
          possible, people should use the new Adaptec written driver instead
          of this one.  This driver will eventually be phased out entirely.

          This is support for the various aic7xxx based Adaptec SCSI
          controllers. These include the 274x EISA cards; 284x VLB cards;
          2902, 2910, 293x, 294x, 394x, 3985 and several other PCI and
          motherboard based SCSI controllers from Adaptec. It does not support
          the AAA-13x RAID controllers from Adaptec, nor will it likely ever
          support them. It does not support the 2920 cards from Adaptec that
          use the Future Domain SCSI controller chip. For those cards, you
          need the "Future Domain 16xx SCSI support" driver.

          In general, if the controller is based on an Adaptec SCSI controller
          chip from the aic777x series or the aic78xx series, this driver
          should work. The only exception is the 7810 which is specifically
          not supported (that's the RAID controller chip on the AAA-13x
          cards).

          Note that the AHA2920 SCSI host adapter is *not* supported by this
          driver; choose "Future Domain 16xx SCSI support" instead if you have
          one of those.

          Information on the configuration options for this controller can be
          found by checking the help file for each of the available
          configuration options. You should read
          <file:Documentation/scsi/aic7xxx_old.txt> at a minimum before
          contacting the maintainer with any questions.  The SCSI-HOWTO,
          available from <http://www.tldp.org/docs.html#howto>, can also
          be of great help.

          To compile this driver as a module, choose M here: the
          module will be called aic7xxx_old.

source "drivers/scsi/aic7xxx/Kconfig.aic79xx"

# All the I2O code and drivers do not seem to be 64bit safe.
config SCSI_DPT_I2O
        tristate "Adaptec I2O RAID support "
        depends on !64BIT && SCSI && PCI
        help
          This driver supports all of Adaptec's I2O based RAID controllers as 
          well as the DPT SmartRaid V cards.  This is an Adaptec maintained
          driver by Deanna Bonds.  See <file:Documentation/scsi/dpti.txt>.

          To compile this driver as a module, choose M here: the
          module will be called dpt_i2o.

config SCSI_ADVANSYS
        tristate "AdvanSys SCSI support"
        depends on (ISA || EISA || PCI) && SCSI && BROKEN
        help
          This is a driver for all SCSI host adapters manufactured by
          AdvanSys. It is documented in the kernel source in
          <file:drivers/scsi/advansys.c>.

          To compile this driver as a module, choose M here: the
          module will be called advansys.

config SCSI_IN2000
        tristate "Always IN2000 SCSI support"
        depends on ISA && SCSI
        help
          This is support for an ISA bus SCSI host adapter.  You'll find more
          information in <file:Documentation/scsi/in2000.txt>. If it doesn't work
          out of the box, you may have to change the jumpers for IRQ or
          address selection.

          To compile this driver as a module, choose M here: the
          module will be called in2000.

source "drivers/scsi/megaraid/Kconfig.megaraid"

config SCSI_SATA
        tristate "Serial ATA (SATA) support"
        depends on SCSI
        help
          This driver family supports Serial ATA host controllers
          and devices.

          If unsure, say N.

config SCSI_SATA_AHCI
        tristate "AHCI SATA support"
        depends on SCSI_SATA && PCI
        help
          This option enables support for AHCI Serial ATA.

          If unsure, say N.

config SCSI_SATA_SVW
        tristate "ServerWorks Frodo / Apple K2 SATA support"
        depends on SCSI_SATA && PCI
        help
          This option enables support for Broadcom/Serverworks/Apple K2
          SATA support.

          If unsure, say N.

config SCSI_ATA_PIIX
        tristate "Intel PIIX/ICH SATA support"
        depends on SCSI_SATA && PCI
        help
          This option enables support for ICH5 Serial ATA.
          If PATA support was enabled previously, this enables
          support for select Intel PIIX/ICH PATA host controllers.

          If unsure, say N.

config SCSI_SATA_MV
        tristate "Marvell SATA support"
        depends on SCSI_SATA && PCI && EXPERIMENTAL
        help
          This option enables support for the Marvell Serial ATA family.
          Currently supports 88SX[56]0[48][01] chips.

          If unsure, say N.

config SCSI_SATA_NV
        tristate "NVIDIA SATA support"
        depends on SCSI_SATA && PCI && EXPERIMENTAL
        help
          This option enables support for NVIDIA Serial ATA.

          If unsure, say N.

config SCSI_SATA_PROMISE
        tristate "Promise SATA TX2/TX4 support"
        depends on SCSI_SATA && PCI
        help
          This option enables support for Promise Serial ATA TX2/TX4.

          If unsure, say N.

config SCSI_SATA_QSTOR
        tristate "Pacific Digital SATA QStor support"
        depends on SCSI_SATA && PCI
        help
          This option enables support for Pacific Digital Serial ATA QStor.

          If unsure, say N.

config SCSI_SATA_SX4
        tristate "Promise SATA SX4 support"
        depends on SCSI_SATA && PCI && EXPERIMENTAL
        help
          This option enables support for Promise Serial ATA SX4.

          If unsure, say N.

config SCSI_SATA_SIL
        tristate "Silicon Image SATA support"
        depends on SCSI_SATA && PCI && EXPERIMENTAL
        help
          This option enables support for Silicon Image Serial ATA.

          If unsure, say N.

config SCSI_SATA_SIS
        tristate "SiS 964/180 SATA support"
        depends on SCSI_SATA && PCI && EXPERIMENTAL
        help
          This option enables support for SiS Serial ATA 964/180.

          If unsure, say N.

config SCSI_SATA_ULI
        tristate "ULi Electronics SATA support"
        depends on SCSI_SATA && PCI && EXPERIMENTAL
        help
          This option enables support for ULi Electronics SATA.

          If unsure, say N.

config SCSI_SATA_VIA
        tristate "VIA SATA support"
        depends on SCSI_SATA && PCI
        help
          This option enables support for VIA Serial ATA.

          If unsure, say N.

config SCSI_SATA_VITESSE
        tristate "VITESSE VSC-7174 SATA support"
        depends on SCSI_SATA && PCI
        help
          This option enables support for Vitesse VSC7174 Serial ATA.

          If unsure, say N.

config SCSI_BUSLOGIC
        tristate "BusLogic SCSI support"
        depends on (PCI || ISA || MCA) && SCSI && ISA_DMA_API
        ---help---
          This is support for BusLogic MultiMaster and FlashPoint SCSI Host
          Adapters. Consult the SCSI-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>, and the files
          <file:Documentation/scsi/BusLogic.txt> and
          <file:Documentation/scsi/FlashPoint.txt> for more information.

          To compile this driver as a module, choose M here: the
          module will be called BusLogic.

config SCSI_OMIT_FLASHPOINT
        bool "Omit FlashPoint support"
        depends on SCSI_BUSLOGIC
        help
          This option allows you to omit the FlashPoint support from the
          BusLogic SCSI driver. The FlashPoint SCCB Manager code is
          substantial, so users of MultiMaster Host Adapters may wish to omit
          it.

#
# This is marked broken because it uses over 4kB of stack in
# just two routines:
#     2076  CpqTsProcessIMQEntry
#     2052  PeekIMQEntry
#
config SCSI_CPQFCTS
        tristate "Compaq Fibre Channel 64-bit/66Mhz HBA support"
        depends on PCI && SCSI && BROKEN
        help
          Say Y here to compile in support for the Compaq StorageWorks Fibre
          Channel 64-bit/66Mhz Host Bus Adapter.

config SCSI_DMX3191D
        tristate "DMX3191D SCSI support"
        depends on PCI && SCSI
        help
          This is support for Domex DMX3191D SCSI Host Adapters.

          To compile this driver as a module, choose M here: the
          module will be called dmx3191d.

config SCSI_DTC3280
        tristate "DTC3180/3280 SCSI support"
        depends on ISA && SCSI
        help
          This is support for DTC 3180/3280 SCSI Host Adapters.  Please read
          the SCSI-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>, and the file
          <file:Documentation/scsi/dtc3x80.txt>.

          To compile this driver as a module, choose M here: the
          module will be called dtc.

config SCSI_EATA
        tristate "EATA ISA/EISA/PCI (DPT and generic EATA/DMA-compliant boards) support"
        depends on (ISA || EISA || PCI) && SCSI && ISA_DMA_API
        ---help---
          This driver supports all EATA/DMA-compliant SCSI host adapters.  DPT
          ISA and all EISA I/O addresses are probed looking for the "EATA"
          signature. The addresses of all the PCI SCSI controllers reported
          by the PCI subsystem are probed as well.

          You want to read the start of <file:drivers/scsi/eata.c> and the
          SCSI-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>.

          To compile this driver as a module, choose M here: the
          module will be called eata.

config SCSI_EATA_TAGGED_QUEUE
        bool "enable tagged command queueing"
        depends on SCSI_EATA
        help
          This is a feature of SCSI-2 which improves performance: the host
          adapter can send several SCSI commands to a device's queue even if
          previous commands haven't finished yet.
          This is equivalent to the "eata=tc:y" boot option.

config SCSI_EATA_LINKED_COMMANDS
        bool "enable elevator sorting"
        depends on SCSI_EATA
        help
          This option enables elevator sorting for all probed SCSI disks and
          CD-ROMs. It definitely reduces the average seek distance when doing
          random seeks, but this does not necessarily result in a noticeable
          performance improvement: your mileage may vary...
          This is equivalent to the "eata=lc:y" boot option.

config SCSI_EATA_MAX_TAGS
        int "maximum number of queued commands"
        depends on SCSI_EATA
        default "16"
        help
          This specifies how many SCSI commands can be maximally queued for
          each probed SCSI device. You should reduce the default value of 16
          only if you have disks with buggy or limited tagged command support.
          Minimum is 2 and maximum is 62. This value is also the window size
          used by the elevator sorting option above. The effective value used
          by the driver for each probed SCSI device is reported at boot time.
          This is equivalent to the "eata=mq:8" boot option.

config SCSI_EATA_PIO
        tristate "EATA-PIO (old DPT PM2001, PM2012A) support"
        depends on (ISA || EISA || PCI) && SCSI && BROKEN
        ---help---
          This driver supports all EATA-PIO protocol compliant SCSI Host
          Adapters like the DPT PM2001 and the PM2012A.  EATA-DMA compliant
          host adapters could also use this driver but are discouraged from
          doing so, since this driver only supports hard disks and lacks
          numerous features.  You might want to have a look at the SCSI-HOWTO,
          available from <http://www.tldp.org/docs.html#howto>.

          To compile this driver as a module, choose M here: the
          module will be called eata_pio.

config SCSI_FUTURE_DOMAIN
        tristate "Future Domain 16xx SCSI/AHA-2920A support"
        depends on (ISA || PCI) && SCSI
        ---help---
          This is support for Future Domain's 16-bit SCSI host adapters
          (TMC-1660/1680, TMC-1650/1670, TMC-3260, TMC-1610M/MER/MEX) and
          other adapters based on the Future Domain chipsets (Quantum
          ISA-200S, ISA-250MG; Adaptec AHA-2920A; and at least one IBM board).
          It is explained in section 3.7 of the SCSI-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>.

          NOTE: Newer Adaptec AHA-2920C boards use the Adaptec AIC-7850 chip
          and should use the aic7xxx driver ("Adaptec AIC7xxx chipset SCSI
          controller support"). This Future Domain driver works with the older
          Adaptec AHA-2920A boards with a Future Domain chip on them.

          To compile this driver as a module, choose M here: the
          module will be called fdomain.

config SCSI_FD_MCS
        tristate "Future Domain MCS-600/700 SCSI support"
        depends on MCA_LEGACY && SCSI
        ---help---
          This is support for Future Domain MCS 600/700 MCA SCSI adapters.
          Some PS/2 computers are equipped with IBM Fast SCSI Adapter/A which
          is identical to the MCS 700 and hence also supported by this driver.
          This driver also supports the Reply SB16/SCSI card (the SCSI part).
          It supports multiple adapters in the same system.

          To compile this driver as a module, choose M here: the
          module will be called fd_mcs.

config SCSI_GDTH
        tristate "Intel/ICP (former GDT SCSI Disk Array) RAID Controller support"
        depends on (ISA || EISA || PCI) && SCSI && ISA_DMA_API
        ---help---
          Formerly called GDT SCSI Disk Array Controller Support.

          This is a driver for RAID/SCSI Disk Array Controllers (EISA/ISA/PCI) 
          manufactured by Intel Corporation/ICP vortex GmbH. It is documented
          in the kernel source in <file:drivers/scsi/gdth.c> and
          <file:drivers/scsi/gdth.h.>

          To compile this driver as a module, choose M here: the
          module will be called gdth.

config SCSI_GENERIC_NCR5380
        tristate "Generic NCR5380/53c400 SCSI PIO support"
        depends on ISA && SCSI
        ---help---
          This is a driver for the old NCR 53c80 series of SCSI controllers
          on boards using PIO. Most boards such as the Trantor T130 fit this
          category, along with a large number of ISA 8bit controllers shipped
          for free with SCSI scanners. If you have a PAS16, T128 or DMX3191
          you should select the specific driver for that card rather than
          generic 5380 support.

          It is explained in section 3.8 of the SCSI-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>.  If it doesn't work out
          of the box, you may have to change some settings in
          <file:drivers/scsi/g_NCR5380.h>.

          To compile this driver as a module, choose M here: the
          module will be called g_NCR5380.

config SCSI_GENERIC_NCR5380_MMIO
        tristate "Generic NCR5380/53c400 SCSI MMIO support"
        depends on ISA && SCSI
        ---help---
          This is a driver for the old NCR 53c80 series of SCSI controllers
          on boards using memory mapped I/O. 
          It is explained in section 3.8 of the SCSI-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>.  If it doesn't work out
          of the box, you may have to change some settings in
          <file:drivers/scsi/g_NCR5380.h>.

          To compile this driver as a module, choose M here: the
          module will be called g_NCR5380_mmio.

config SCSI_GENERIC_NCR53C400
        bool "Enable NCR53c400 extensions"
        depends on SCSI_GENERIC_NCR5380
        help
          This enables certain optimizations for the NCR53c400 SCSI cards.
          You might as well try it out.  Note that this driver will only probe
          for the Trantor T130B in its default configuration; you might have
          to pass a command line option to the kernel at boot time if it does
          not detect your card.  See the file
          <file:Documentation/scsi/g_NCR5380.txt> for details.

config SCSI_IBMMCA
        tristate "IBMMCA SCSI support"
        depends on MCA_LEGACY && SCSI
        ---help---
          This is support for the IBM SCSI adapter found in many of the PS/2
          series computers.  These machines have an MCA bus, so you need to
          answer Y to "MCA support" as well and read
          <file:Documentation/mca.txt>.

          If the adapter isn't found during boot (a common problem for models
          56, 57, 76, and 77) you'll need to use the 'ibmmcascsi=<pun>' kernel
          option, where <pun> is the id of the SCSI subsystem (usually 7, but
          if that doesn't work check your reference diskette).  Owners of
          model 95 with a LED-matrix-display can in addition activate some
          activity info like under OS/2, but more informative, by setting
          'ibmmcascsi=display' as an additional kernel parameter.  Try "man
          bootparam" or see the documentation of your boot loader about how to
          pass options to the kernel.

          To compile this driver as a module, choose M here: the
          module will be called ibmmca.

config IBMMCA_SCSI_ORDER_STANDARD
        bool "Standard SCSI-order"
        depends on SCSI_IBMMCA
        ---help---
          In the PC-world and in most modern SCSI-BIOS-setups, SCSI-hard disks
          are assigned to the drive letters, starting with the lowest SCSI-id
          (physical number -- pun) to be drive C:, as seen from DOS and
          similar operating systems. When looking into papers describing the
          ANSI-SCSI-standard, this assignment of drives appears to be wrong.
          The SCSI-standard follows a hardware-hierarchy which says that id 7
          has the highest priority and id 0 the lowest. Therefore, the host
          adapters are still today everywhere placed as SCSI-id 7 by default.
          In the SCSI-standard, the drive letters express the priority of the
          disk. C: should be the hard disk, or a partition on it, with the
          highest priority. This must therefore be the disk with the highest
          SCSI-id (e.g. 6) and not the one with the lowest! IBM-BIOS kept the
          original definition of the SCSI-standard as also industrial- and
          process-control-machines, like VME-CPUs running under realtime-OSes
          (e.g. LynxOS, OS9) do.

          If you like to run Linux on your MCA-machine with the same
          assignment of hard disks as seen from e.g. DOS or OS/2 on your
          machine, which is in addition conformant to the SCSI-standard, you
          must say Y here. This is also necessary for MCA-Linux users who want
          to keep downward compatibility to older releases of the
          IBM-MCA-SCSI-driver (older than driver-release 2.00 and older than
          June 1997).

          If you like to have the lowest SCSI-id assigned as drive C:, as
          modern SCSI-BIOSes do, which does not conform to the standard, but
          is widespread and common in the PC-world of today, you must say N
          here. If unsure, say Y.

config IBMMCA_SCSI_DEV_RESET
        bool "Reset SCSI-devices at boottime"
        depends on SCSI_IBMMCA
        ---help---
          By default, SCSI-devices are reset when the machine is powered on.
          However, some devices exist, like special-control-devices,
          SCSI-CNC-machines, SCSI-printer or scanners of older type, that do
          not reset when switched on. If you say Y here, each device connected
          to your SCSI-bus will be issued a reset-command after it has been
          probed, while the kernel is booting. This may cause problems with
          more modern devices, like hard disks, which do not appreciate these
          reset commands, and can cause your system to hang. So say Y only if
          you know that one of your older devices needs it; N is the safe
          answer.

config SCSI_IPS
        tristate "IBM ServeRAID support"
        depends on PCI && SCSI
        ---help---
          This is support for the IBM ServeRAID hardware RAID controllers.
          See <http://www.developer.ibm.com/welcome/netfinity/serveraid.html>
          for more information.  If this driver does not work correctly
          without modification please contact the author by email at
          <ipslinux@adaptec.com>.

          To compile this driver as a module, choose M here: the
          module will be called ips.

config SCSI_IBMVSCSI
        tristate "IBM Virtual SCSI support"
        depends on PPC_PSERIES || PPC_ISERIES
        help
          This is the IBM POWER Virtual SCSI Client

          To compile this driver as a module, choose M here: the
          module will be called ibmvscsic.

config SCSI_INITIO
        tristate "Initio 9100U(W) support"
        depends on PCI && SCSI
        help
          This is support for the Initio 91XXU(W) SCSI host adapter.  Please
          read the SCSI-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>.

          To compile this driver as a module, choose M here: the
          module will be called initio.

config SCSI_INIA100
        tristate "Initio INI-A100U2W support"
        depends on PCI && SCSI
        help
          This is support for the Initio INI-A100U2W SCSI host adapter.
          Please read the SCSI-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>.

          To compile this driver as a module, choose M here: the
          module will be called a100u2w.

config SCSI_PPA
        tristate "IOMEGA parallel port (ppa - older drives)"
        depends on SCSI && PARPORT
        ---help---
          This driver supports older versions of IOMEGA's parallel port ZIP
          drive (a 100 MB removable media device).

          Note that you can say N here if you have the SCSI version of the ZIP
          drive: it will be supported automatically if you said Y to the
          generic "SCSI disk support", above.

          If you have the ZIP Plus drive or a more recent parallel port ZIP
          drive (if the supplied cable with the drive is labeled "AutoDetect")
          then you should say N here and Y to "IOMEGA parallel port (imm -
          newer drives)", below.

          For more information about this driver and how to use it you should
          read the file <file:Documentation/scsi/ppa.txt>.  You should also read
          the SCSI-HOWTO, which is available from
          <http://www.tldp.org/docs.html#howto>.  If you use this driver,
          you will still be able to use the parallel port for other tasks,
          such as a printer; it is safe to compile both drivers into the
          kernel.

          To compile this driver as a module, choose M here: the
          module will be called ppa.

config SCSI_IMM
        tristate "IOMEGA parallel port (imm - newer drives)"
        depends on SCSI && PARPORT
        ---help---
          This driver supports newer versions of IOMEGA's parallel port ZIP
          drive (a 100 MB removable media device).

          Note that you can say N here if you have the SCSI version of the ZIP
          drive: it will be supported automatically if you said Y to the
          generic "SCSI disk support", above.

          If you have the ZIP Plus drive or a more recent parallel port ZIP
          drive (if the supplied cable with the drive is labeled "AutoDetect")
          then you should say Y here; if you have an older ZIP drive, say N
          here and Y to "IOMEGA Parallel Port (ppa - older drives)", above.

          For more information about this driver and how to use it you should
          read the file <file:Documentation/scsi/ppa.txt>.  You should also read
          the SCSI-HOWTO, which is available from
          <http://www.tldp.org/docs.html#howto>.  If you use this driver,
          you will still be able to use the parallel port for other tasks,
          such as a printer; it is safe to compile both drivers into the
          kernel.

          To compile this driver as a module, choose M here: the
          module will be called imm.

config SCSI_IZIP_EPP16
        bool "ppa/imm option - Use slow (but safe) EPP-16"
        depends on PARPORT && (SCSI_PPA || SCSI_IMM)
        ---help---
          EPP (Enhanced Parallel Port) is a standard for parallel ports which
          allows them to act as expansion buses that can handle up to 64
          peripheral devices.

          Some parallel port chipsets are slower than their motherboard, and
          so we have to control the state of the chipset's FIFO queue every
          now and then to avoid data loss. This will be done if you say Y
          here.

          Generally, saying Y is the safe option and slows things down a bit.

config SCSI_IZIP_SLOW_CTR
        bool "ppa/imm option - Assume slow parport control register"
        depends on PARPORT && (SCSI_PPA || SCSI_IMM)
        help
          Some parallel ports are known to have excessive delays between
          changing the parallel port control register and good data being
          available on the parallel port data/status register. This option
          forces a small delay (1.0 usec to be exact) after changing the
          control register to let things settle out. Enabling this option may
          result in a big drop in performance but some very old parallel ports
          (found in 386 vintage machines) will not work properly.

          Generally, saying N is fine.

config SCSI_NCR53C406A
        tristate "NCR53c406a SCSI support"
        depends on ISA && SCSI
        help
          This is support for the NCR53c406a SCSI host adapter.  For user
          configurable parameters, check out <file:drivers/scsi/NCR53c406a.c>
          in the kernel source.  Also read the SCSI-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>.

          To compile this driver as a module, choose M here: the
          module will be called NCR53c406.

config SCSI_NCR_D700
        tristate "NCR Dual 700 MCA SCSI support"
        depends on MCA && SCSI
        select SCSI_SPI_ATTRS
        help
          This is a driver for the MicroChannel Dual 700 card produced by
          NCR and commonly used in 345x/35xx/4100 class machines.  It always
          tries to negotiate sync and uses tag command queueing.

          Unless you have an NCR manufactured machine, the chances are that
          you do not have this SCSI card, so say N.

config SCSI_LASI700
        tristate "HP Lasi SCSI support for 53c700/710"
        depends on GSC && SCSI
        select SCSI_SPI_ATTRS
        help
          This is a driver for the SCSI controller in the Lasi chip found in
          many PA-RISC workstations & servers.  If you do not know whether you
          have a Lasi chip, it is safe to say "Y" here.

config 53C700_LE_ON_BE
        bool
        depends on SCSI_LASI700
        default y

config SCSI_SYM53C8XX_2
        tristate "SYM53C8XX Version 2 SCSI support"
        depends on PCI && SCSI
        select SCSI_SPI_ATTRS
        ---help---
          This driver supports the whole NCR53C8XX/SYM53C8XX family of
          PCI-SCSI controllers.  It also supports the subset of LSI53C10XX
          Ultra-160 controllers that are based on the SYM53C8XX SCRIPTS
          language.  It does not support LSI53C10XX Ultra-320 PCI-X SCSI
          controllers; you need to use the Fusion MPT driver for that.

          Please read <file:Documentation/scsi/sym53c8xx_2.txt> for more
          information.

config SCSI_SYM53C8XX_DMA_ADDRESSING_MODE
        int "DMA addressing mode"
        depends on SCSI_SYM53C8XX_2
        default "1"
        ---help---
          This option only applies to PCI-SCSI chips that are PCI DAC
          capable (875A, 895A, 896, 1010-33, 1010-66, 1000).

          When set to 0, the driver will program the chip to only perform
          32-bit DMA.  When set to 1, the chip will be able to perform DMA
          to addresses up to 1TB.  When set to 2, the driver supports the
          full 64-bit DMA address range, but can only address 16 segments
          of 4 GB each.  This limits the total addressable range to 64 GB.

          Most machines with less than 4GB of memory should use a setting
          of 0 for best performance.  If your machine has 4GB of memory
          or more, you should set this option to 1 (the default).

          The still experimental value 2 (64 bit DMA addressing with 16
          x 4GB segments limitation) can be used on systems that require
          PCI address bits past bit 39 to be set for the addressing of
          memory using PCI DAC cycles.

config SCSI_SYM53C8XX_DEFAULT_TAGS
        int "default tagged command queue depth"
        depends on SCSI_SYM53C8XX_2
        default "16"
        help
          This is the default value of the command queue depth the
          driver will announce to the generic SCSI layer for devices
          that support tagged command queueing. This value can be changed
          from the boot command line.  This is a soft limit that cannot
          exceed CONFIG_SCSI_SYM53C8XX_MAX_TAGS.

config SCSI_SYM53C8XX_MAX_TAGS
        int "maximum number of queued commands"
        depends on SCSI_SYM53C8XX_2
        default "64"
        help
          This option allows you to specify the maximum number of commands
          that can be queued to any device, when tagged command queuing is
          possible. The driver supports up to 256 queued commands per device.
          This value is used as a compiled-in hard limit.

config SCSI_SYM53C8XX_IOMAPPED
        bool "use port IO"
        depends on SCSI_SYM53C8XX_2
        help
          If you say Y here, the driver will use port IO to access
          the card.  This is significantly slower then using memory
          mapped IO.  Most people should answer N.

config SCSI_IPR
        tristate "IBM Power Linux RAID adapter support"
        depends on PCI && SCSI
        select FW_LOADER
        ---help---
          This driver supports the IBM Power Linux family RAID adapters.
          This includes IBM pSeries 5712, 5703, 5709, and 570A, as well
          as IBM iSeries 5702, 5703, 5709, and 570A.

config SCSI_IPR_TRACE
        bool "enable driver internal trace"
        depends on SCSI_IPR
        help
          If you say Y here, the driver will trace all commands issued
          to the adapter. Performance impact is minimal. Trace can be
          dumped using /sys/bus/class/scsi_host/hostXX/trace.

config SCSI_IPR_DUMP
        bool "enable adapter dump support"
        depends on SCSI_IPR
        help
          If you say Y here, the driver will support adapter crash dump.
          If you enable this support, the iprdump daemon can be used
          to capture adapter failure analysis information.

config SCSI_ZALON
        tristate "Zalon SCSI support"
        depends on GSC && SCSI
        select SCSI_SPI_ATTRS
        help
          The Zalon is a GSC/HSC bus interface chip that sits between the
          PA-RISC processor and the NCR 53c720 SCSI controller on C100,
          C110, J200, J210 and some D, K & R-class machines.  It's also
          used on the add-in Bluefish, Barracuda & Shrike SCSI cards.
          Say Y here if you have one of these machines or cards.

config SCSI_NCR_Q720
        tristate "NCR Quad 720 MCA SCSI support"
        depends on MCA && SCSI
        select SCSI_SPI_ATTRS
        help
          This is a driver for the MicroChannel Quad 720 card produced by
          NCR and commonly used in 345x/35xx/4100 class machines.  It always
          tries to negotiate sync and uses tag command queueing.

          Unless you have an NCR manufactured machine, the chances are that
          you do not have this SCSI card, so say N.

config SCSI_NCR53C8XX_DEFAULT_TAGS
        int "  default tagged command queue depth"
        depends on SCSI_ZALON || SCSI_NCR_Q720
        default "8"
        ---help---
          "Tagged command queuing" is a feature of SCSI-2 which improves
          performance: the host adapter can send several SCSI commands to a
          device's queue even if previous commands haven't finished yet.
          Because the device is intelligent, it can optimize its operations
          (like head positioning) based on its own request queue. Some SCSI
          devices don't implement this properly; if you want to disable this
          feature, enter 0 or 1 here (it doesn't matter which).

          The default value is 8 and should be supported by most hard disks.
          This value can be overridden from the boot command line using the
          'tags' option as follows (example):
          'ncr53c8xx=tags:4/t2t3q16/t0u2q10' will set default queue depth to
          4, set queue depth to 16 for target 2 and target 3 on controller 0
          and set queue depth to 10 for target 0 / lun 2 on controller 1.

          The normal answer therefore is to go with the default 8 and to use
          a boot command line option for devices that need to use a different
          command queue depth.

          There is no safe option other than using good SCSI devices.

config SCSI_NCR53C8XX_MAX_TAGS
        int "  maximum number of queued commands"
        depends on SCSI_ZALON || SCSI_NCR_Q720
        default "32"
        ---help---
          This option allows you to specify the maximum number of commands
          that can be queued to any device, when tagged command queuing is
          possible. The default value is 32. Minimum is 2, maximum is 64.
          Modern hard disks are able to support 64 tags and even more, but
          do not seem to be faster when more than 32 tags are being used.

          So, the normal answer here is to go with the default value 32 unless
          you are using very large hard disks with large cache (>= 1 MB) that
          are able to take advantage of more than 32 tagged commands.

          There is no safe option and the default answer is recommended.

config SCSI_NCR53C8XX_SYNC
        int "  synchronous transfers frequency in MHz"
        depends on SCSI_ZALON || SCSI_NCR_Q720
        default "20"
        ---help---
          The SCSI Parallel Interface-2 Standard defines 5 classes of transfer
          rates: FAST-5, FAST-10, FAST-20, FAST-40 and FAST-80.  The numbers
          are respectively the maximum data transfer rates in mega-transfers
          per second for each class.  For example, a FAST-20 Wide 16 device is
          able to transfer data at 20 million 16 bit packets per second for a
          total rate of 40 MB/s.

          You may specify 0 if you want to only use asynchronous data
          transfers. This is the safest and slowest option. Otherwise, specify
          a value between 5 and 80, depending on the capability of your SCSI
          controller.  The higher the number, the faster the data transfer.
          Note that 80 should normally be ok since the driver decreases the
          value automatically according to the controller's capabilities.

          Your answer to this question is ignored for controllers with NVRAM,
          since the driver will get this information from the user set-up.  It
          also can be overridden using a boot setup option, as follows
          (example): 'ncr53c8xx=sync:12' will allow the driver to negotiate
          for FAST-20 synchronous data transfer (20 mega-transfers per
          second).

          The normal answer therefore is not to go with the default but to
          select the maximum value 80 allowing the driver to use the maximum
          value supported by each controller. If this causes problems with
          your SCSI devices, you should come back and decrease the value.

          There is no safe option other than using good cabling, right
          terminations and SCSI conformant devices.

config SCSI_NCR53C8XX_PROFILE
        bool "  enable profiling"
        depends on SCSI_ZALON || SCSI_NCR_Q720
        help
          This option allows you to enable profiling information gathering.
          These statistics are not very accurate due to the low frequency
          of the kernel clock (100 Hz on i386) and have performance impact
          on systems that use very fast devices.

          The normal answer therefore is N.

config SCSI_NCR53C8XX_NO_DISCONNECT
        bool "  not allow targets to disconnect"
        depends on (SCSI_ZALON || SCSI_NCR_Q720) && SCSI_NCR53C8XX_DEFAULT_TAGS=0
        help
          This option is only provided for safety if you suspect some SCSI
          device of yours to not support properly the target-disconnect
          feature. In that case, you would say Y here. In general however, to
          not allow targets to disconnect is not reasonable if there is more
          than 1 device on a SCSI bus. The normal answer therefore is N.

config SCSI_MCA_53C9X
        tristate "NCR MCA 53C9x SCSI support"
        depends on MCA_LEGACY && SCSI && BROKEN_ON_SMP
        help
          Some MicroChannel machines, notably the NCR 35xx line, use a SCSI
          controller based on the NCR 53C94.  This driver will allow use of
          the controller on the 3550, and very possibly others.

          To compile this driver as a module, choose M here: the
          module will be called mca_53c9x.

config SCSI_PAS16
        tristate "PAS16 SCSI support"
        depends on ISA && SCSI
        ---help---
          This is support for a SCSI host adapter.  It is explained in section
          3.10 of the SCSI-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>.  If it doesn't work out
          of the box, you may have to change some settings in
          <file:drivers/scsi/pas16.h>.

          To compile this driver as a module, choose M here: the
          module will be called pas16.

config SCSI_PSI240I
        tristate "PSI240i support"
        depends on ISA && SCSI
        help
          This is support for the PSI240i EIDE interface card which acts as a
          SCSI host adapter.  Please read the SCSI-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>.

          To compile this driver as a module, choose M here: the
          module will be called psi240i.

config SCSI_QLOGIC_FAS
        tristate "Qlogic FAS SCSI support"
        depends on ISA && SCSI
        ---help---
          This is a driver for the ISA, VLB, and PCMCIA versions of the Qlogic
          FastSCSI! cards as well as any other card based on the FASXX chip
          (including the Control Concepts SCSI/IDE/SIO/PIO/FDC cards).

          This driver does NOT support the PCI versions of these cards. The
          PCI versions are supported by the Qlogic ISP driver ("Qlogic ISP
          SCSI support"), below.

          Information about this driver is contained in
          <file:Documentation/scsi/qlogicfas.txt>.  You should also read the
          SCSI-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>.

          To compile this driver as a module, choose M here: the
          module will be called qlogicfas.

config SCSI_QLOGIC_ISP
        tristate "Qlogic ISP SCSI support (old driver)"
        depends on PCI && SCSI && BROKEN
        ---help---
          This driver works for all QLogic PCI SCSI host adapters (IQ-PCI,
          IQ-PCI-10, IQ_PCI-D) except for the PCI-basic card.  (This latter
          card is supported by the "AM53/79C974 PCI SCSI" driver.)

          If you say Y here, make sure to choose "BIOS" at the question "PCI
          access mode".

          Please read the file <file:Documentation/scsi/qlogicisp.txt>.  You
          should also read the SCSI-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>.

          To compile this driver as a module, choose M here: the
          module will be called qlogicisp.

          These days the hardware is also supported by the more modern qla1280
          driver.  In doubt use that one instead of qlogicisp.

config SCSI_QLOGIC_FC
        tristate "Qlogic ISP FC SCSI support"
        depends on PCI && SCSI
        help
          This is a driver for the QLogic ISP2100 SCSI-FCP host adapter.

          To compile this driver as a module, choose M here: the
          module will be called qlogicfc.

config SCSI_QLOGIC_FC_FIRMWARE
        bool "Include loadable firmware in driver"
        depends on SCSI_QLOGIC_FC
        help
          Say Y to include ISP2X00 Fabric Initiator/Target Firmware, with
          expanded LUN addressing and FcTape (FCP-2) support, in the
          qlogicfc driver. This is required on some platforms.

config SCSI_QLOGIC_1280
        tristate "Qlogic QLA 1240/1x80/1x160 SCSI support"
        depends on PCI && SCSI
        help
          Say Y if you have a QLogic ISP1240/1x80/1x160 SCSI host adapter.

          To compile this driver as a module, choose M here: the
          module will be called qla1280.

config SCSI_QLOGIC_1280_1040
        bool "Qlogic QLA 1020/1040 SCSI support"
        depends on SCSI_QLOGIC_1280 && SCSI_QLOGIC_ISP!=y
        help
          Say Y here if you have a QLogic ISP1020/1040 SCSI host adapter and
          do not want to use the old driver.  This option enables support in
          the qla1280 driver for those host adapters.

config SCSI_QLOGICPTI
        tristate "PTI Qlogic, ISP Driver"
        depends on SBUS && SCSI
        help
          This driver supports SBUS SCSI controllers from PTI or QLogic. These
          controllers are known under Solaris as qpti and in the openprom as
          PTI,ptisp or QLGC,isp. Note that PCI QLogic SCSI controllers are
          driven by a different driver.

          To compile this driver as a module, choose M here: the
          module will be called qlogicpti.

source "drivers/scsi/qla2xxx/Kconfig"

config SCSI_LPFC
        tristate "Emulex LightPulse Fibre Channel Support"
        depends on PCI && SCSI
        select SCSI_FC_ATTRS
        help
          This lpfc driver supports the Emulex LightPulse
          Family of Fibre Channel PCI host adapters.

config SCSI_SEAGATE
        tristate "Seagate ST-02 and Future Domain TMC-8xx SCSI support"
        depends on X86 && ISA && SCSI && BROKEN
        ---help---
          These are 8-bit SCSI controllers; the ST-01 is also supported by
          this driver.  It is explained in section 3.9 of the SCSI-HOWTO,
          available from <http://www.tldp.org/docs.html#howto>.  If it
          doesn't work out of the box, you may have to change some settings in
          <file:drivers/scsi/seagate.h>.

          To compile this driver as a module, choose M here: the
          module will be called seagate.

# definitely looks not 64bit safe:
config SCSI_SIM710
        tristate "Simple 53c710 SCSI support (Compaq, NCR machines)"
        depends on (EISA || MCA) && SCSI
        select SCSI_SPI_ATTRS
        ---help---
          This driver for NCR53c710 based SCSI host adapters.

          It currently supports Compaq EISA cards and NCR MCA cards

config 53C700_IO_MAPPED
        bool
        depends on SCSI_SIM710
        default y

config SCSI_SYM53C416
        tristate "Symbios 53c416 SCSI support"
        depends on ISA && SCSI
        ---help---
          This is support for the sym53c416 SCSI host adapter, the SCSI
          adapter that comes with some HP scanners. This driver requires that
          the sym53c416 is configured first using some sort of PnP
          configuration program (e.g. isapnp) or by a PnP aware BIOS. If you
          are using isapnp then you need to compile this driver as a module
          and then load it using insmod after isapnp has run. The parameters
          of the configured card(s) should be passed to the driver. The format
          is:

          insmod sym53c416 sym53c416=<base>,<irq> [sym53c416_1=<base>,<irq>]

          To compile this driver as a module, choose M here: the
          module will be called sym53c416.

config SCSI_DC395x
        tristate "Tekram DC395(U/UW/F) and DC315(U) SCSI support (EXPERIMENTAL)"
        depends on PCI && SCSI && EXPERIMENTAL
        ---help---
          This driver supports PCI SCSI host adapters based on the ASIC
          TRM-S1040 chip, e.g Tekram DC395(U/UW/F) and DC315(U) variants.

          This driver works, but is still in experimental status. So better
          have a bootable disk and a backup in case of emergency.

          Documentation can be found in <file:Documentation/scsi/dc395x.txt>.

          To compile this driver as a module, choose M here: the
          module will be called dc395x.

config SCSI_DC390T
        tristate "Tekram DC390(T) and Am53/79C974 SCSI support"
        depends on PCI && SCSI
        ---help---
          This driver supports PCI SCSI host adapters based on the Am53C974A
          chip, e.g. Tekram DC390(T), DawiControl 2974 and some onboard
          PCscsi/PCnet (Am53/79C974) solutions.

          Documentation can be found in <file:Documentation/scsi/tmscsim.txt>.

          Note that this driver does NOT support Tekram DC390W/U/F, which are
          based on NCR/Symbios chips. Use "NCR53C8XX SCSI support" for those.

          To compile this driver as a module, choose M here: the
          module will be called tmscsim.

config SCSI_T128
        tristate "Trantor T128/T128F/T228 SCSI support"
        depends on ISA && SCSI
        ---help---
          This is support for a SCSI host adapter. It is explained in section
          3.11 of the SCSI-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>.  If it doesn't work out
          of the box, you may have to change some settings in
          <file:drivers/scsi/t128.h>.  Note that Trantor was purchased by
          Adaptec, and some former Trantor products are being sold under the
          Adaptec name.

          To compile this driver as a module, choose M here: the
          module will be called t128.

config SCSI_U14_34F
        tristate "UltraStor 14F/34F support"
        depends on ISA && SCSI && ISA_DMA_API
        ---help---
          This is support for the UltraStor 14F and 34F SCSI-2 host adapters.
          The source at <file:drivers/scsi/u14-34f.c> contains some
          information about this hardware.  If the driver doesn't work out of
          the box, you may have to change some settings in
          <file: drivers/scsi/u14-34f.c>.  Read the SCSI-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>.  Note that there is also
          another driver for the same hardware: "UltraStor SCSI support",
          below.  You should say Y to both only if you want 24F support as
          well.

          To compile this driver as a module, choose M here: the
          module will be called u14-34f.

config SCSI_U14_34F_TAGGED_QUEUE
        bool "enable tagged command queueing"
        depends on SCSI_U14_34F
        help
          This is a feature of SCSI-2 which improves performance: the host
          adapter can send several SCSI commands to a device's queue even if
          previous commands haven't finished yet.
          This is equivalent to the "u14-34f=tc:y" boot option.

config SCSI_U14_34F_LINKED_COMMANDS
        bool "enable elevator sorting"
        depends on SCSI_U14_34F
        help
          This option enables elevator sorting for all probed SCSI disks and
          CD-ROMs. It definitely reduces the average seek distance when doing
          random seeks, but this does not necessarily result in a noticeable
          performance improvement: your mileage may vary...
          This is equivalent to the "u14-34f=lc:y" boot option.

config SCSI_U14_34F_MAX_TAGS
        int "maximum number of queued commands"
        depends on SCSI_U14_34F
        default "8"
        help
          This specifies how many SCSI commands can be maximally queued for
          each probed SCSI device. You should reduce the default value of 8
          only if you have disks with buggy or limited tagged command support.
          Minimum is 2 and maximum is 14. This value is also the window size
          used by the elevator sorting option above. The effective value used
          by the driver for each probed SCSI device is reported at boot time.
          This is equivalent to the "u14-34f=mq:8" boot option.

config SCSI_ULTRASTOR
        tristate "UltraStor SCSI support"
        depends on X86 && ISA && SCSI
        ---help---
          This is support for the UltraStor 14F, 24F and 34F SCSI-2 host
          adapter family.  This driver is explained in section 3.12 of the
          SCSI-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>.  If it doesn't work out
          of the box, you may have to change some settings in
          <file:drivers/scsi/ultrastor.h>.

          Note that there is also another driver for the same hardware:
          "UltraStor 14F/34F support", above.

          To compile this driver as a module, choose M here: the
          module will be called ultrastor.

config SCSI_NSP32
        tristate "Workbit NinjaSCSI-32Bi/UDE support"
        depends on PCI && SCSI && !64BIT
        help
          This is support for the Workbit NinjaSCSI-32Bi/UDE PCI/Cardbus
          SCSI host adapter. Please read the SCSI-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>.

          To compile this driver as a module, choose M here: the
          module will be called nsp32.

config SCSI_DEBUG
        tristate "SCSI debugging host simulator"
        depends on SCSI
        help
          This is a host adapter simulator that can simulate multiple hosts
          each with multiple dummy SCSI devices (disks). It defaults to one
          host adapter with one dummy SCSI disk. Each dummy disk uses kernel
          RAM as storage (i.e. it is a ramdisk). To save space when multiple
          dummy disks are simulated, they share the same kernel RAM for 
          their storage. See <http://www.torque.net/sg/sdebug.html> for more
          information. This driver is primarily of use to those testing the
          SCSI and block subsystems. If unsure, say N.

config SCSI_MESH
        tristate "MESH (Power Mac internal SCSI) support"
        depends on PPC32 && PPC_PMAC && SCSI
        help
          Many Power Macintoshes and clones have a MESH (Macintosh Enhanced
          SCSI Hardware) SCSI bus adaptor (the 7200 doesn't, but all of the
          other Power Macintoshes do). Say Y to include support for this SCSI
          adaptor.

          To compile this driver as a module, choose M here: the
          module will be called mesh.

config SCSI_MESH_SYNC_RATE
        int "maximum synchronous transfer rate (MB/s) (0 = async)"
        depends on SCSI_MESH
        default "5"
        help
          On Power Macintoshes (and clones) where the MESH SCSI bus adaptor
          drives a bus which is entirely internal to the machine (such as the
          7500, 7600, 8500, etc.), the MESH is capable of synchronous
          operation at up to 10 MB/s. On machines where the SCSI bus
          controlled by the MESH can have external devices connected, it is
          usually rated at 5 MB/s. 5 is a safe value here unless you know the
          MESH SCSI bus is internal only; in that case you can say 10. Say 0
          to disable synchronous operation.

config SCSI_MESH_RESET_DELAY_MS
        int "initial bus reset delay (ms) (0 = no reset)"
        depends on SCSI_MESH
        default "4000"

config SCSI_MAC53C94
        tristate "53C94 (Power Mac external SCSI) support"
        depends on PPC32 && PPC_PMAC && SCSI
        help
          On Power Macintoshes (and clones) with two SCSI buses, the external
          SCSI bus is usually controlled by a 53C94 SCSI bus adaptor. Older
          machines which only have one SCSI bus, such as the 7200, also use
          the 53C94. Say Y to include support for the 53C94.

          To compile this driver as a module, choose M here: the
          module will be called mac53c94.

source "drivers/scsi/arm/Kconfig"

config JAZZ_ESP
        bool "MIPS JAZZ FAS216 SCSI support"
        depends on MACH_JAZZ && SCSI
        help
          This is the driver for the onboard SCSI host adapter of MIPS Magnum
          4000, Acer PICA, Olivetti M700-10 and a few other identical OEM
          systems.

config A3000_SCSI
        tristate "A3000 WD33C93A support"
        depends on AMIGA && SCSI
        help
          If you have an Amiga 3000 and have SCSI devices connected to the
          built-in SCSI controller, say Y. Otherwise, say N.

          To compile this driver as a module, choose M here: the
          module will be called wd33c93.

config A2091_SCSI
        tristate "A2091/A590 WD33C93A support"
        depends on ZORRO && SCSI
        help
          If you have a Commodore A2091 SCSI controller, say Y. Otherwise,
          say N.

          To compile this driver as a module, choose M here: the
          module will be called wd33c93.

config GVP11_SCSI
        tristate "GVP Series II WD33C93A support"
        depends on ZORRO && SCSI
        ---help---
          If you have a Great Valley Products Series II SCSI controller,
          answer Y. Also say Y if you have a later model of GVP SCSI
          controller (such as the GVP A4008 or a Combo board). Otherwise,
          answer N. This driver does NOT work for the T-Rex series of
          accelerators from TekMagic and GVP-M.

          To compile this driver as a module, choose M here: the
          module will be called gvp11.

config CYBERSTORM_SCSI
        tristate "CyberStorm SCSI support"
        depends on ZORRO && SCSI
        help
          If you have an Amiga with an original (MkI) Phase5 Cyberstorm
          accelerator board and the optional Cyberstorm SCSI controller,
          answer Y. Otherwise, say N.

config CYBERSTORMII_SCSI
        tristate "CyberStorm Mk II SCSI support"
        depends on ZORRO && SCSI
        help
          If you have an Amiga with a Phase5 Cyberstorm MkII accelerator board
          and the optional Cyberstorm SCSI controller, say Y. Otherwise,
          answer N.

config BLZ2060_SCSI
        tristate "Blizzard 2060 SCSI support"
        depends on ZORRO && SCSI
        help
          If you have an Amiga with a Phase5 Blizzard 2060 accelerator board
          and want to use the onboard SCSI controller, say Y. Otherwise,
          answer N.

config BLZ1230_SCSI
        tristate "Blizzard 1230IV/1260 SCSI support"
        depends on ZORRO && SCSI
        help
          If you have an Amiga 1200 with a Phase5 Blizzard 1230IV or Blizzard
          1260 accelerator, and the optional SCSI module, say Y. Otherwise,
          say N.

config FASTLANE_SCSI
        tristate "Fastlane SCSI support"
        depends on ZORRO && SCSI
        help
          If you have the Phase5 Fastlane Z3 SCSI controller, or plan to use
          one in the near future, say Y to this question. Otherwise, say N.

config SCSI_AMIGA7XX
        bool "Amiga NCR53c710 SCSI support (EXPERIMENTAL)"
        depends on AMIGA && SCSI && EXPERIMENTAL && BROKEN
        help
          Support for various NCR53c710-based SCSI controllers on the Amiga.
          This includes:
            - the builtin SCSI controller on the Amiga 4000T,
            - the Amiga 4091 Zorro III SCSI-2 controller,
            - the MacroSystem Development's WarpEngine Amiga SCSI-2 controller
              (info at
              <http://www.lysator.liu.se/amiga/ar/guide/ar310.guide?FEATURE5>),
            - the SCSI controller on the Phase5 Blizzard PowerUP 603e+
              accelerator card for the Amiga 1200,
            - the SCSI controller on the GVP Turbo 040/060 accelerator.
          Note that all of the above SCSI controllers, except for the builtin
          SCSI controller on the Amiga 4000T, reside on the Zorro expansion
          bus, so you also have to enable Zorro bus support if you want to use
          them.

config OKTAGON_SCSI
        tristate "BSC Oktagon SCSI support (EXPERIMENTAL)"
        depends on ZORRO && SCSI && EXPERIMENTAL
        help
          If you have the BSC Oktagon SCSI disk controller for the Amiga, say
          Y to this question.  If you're in doubt about whether you have one,
          see the picture at
          <http://amiga.resource.cx/exp/search.pl?product=oktagon>.

config ATARI_SCSI
        tristate "Atari native SCSI support"
        depends on ATARI && SCSI && BROKEN
        ---help---
          If you have an Atari with built-in NCR5380 SCSI controller (TT,
          Falcon, ...) say Y to get it supported. Of course also, if you have
          a compatible SCSI controller (e.g. for Medusa).

          To compile this driver as a module, choose M here: the
          module will be called atari_scsi.

          This driver supports both styles of NCR integration into the
          system: the TT style (separate DMA), and the Falcon style (via
          ST-DMA, replacing ACSI).  It does NOT support other schemes, like
          in the Hades (without DMA).

config ATARI_SCSI_TOSHIBA_DELAY
        bool "Long delays for Toshiba CD-ROMs"
        depends on ATARI_SCSI
        help
          This option increases the delay after a SCSI arbitration to
          accommodate some flaky Toshiba CD-ROM drives. Say Y if you intend to
          use a Toshiba CD-ROM drive; otherwise, the option is not needed and
          would impact performance a bit, so say N.

config ATARI_SCSI_RESET_BOOT
        bool "Reset SCSI-devices at boottime"
        depends on ATARI_SCSI
        help
          Reset the devices on your Atari whenever it boots.  This makes the
          boot process fractionally longer but may assist recovery from errors
          that leave the devices with SCSI operations partway completed.

config TT_DMA_EMUL
        bool "Hades SCSI DMA emulator"
        depends on ATARI_SCSI && HADES
        help
          This option enables code which emulates the TT SCSI DMA chip on the
          Hades. This increases the SCSI transfer rates at least ten times
          compared to PIO transfers.

config MAC_SCSI
        bool "Macintosh NCR5380 SCSI"
        depends on MAC && SCSI=y
        help
          This is the NCR 5380 SCSI controller included on most of the 68030
          based Macintoshes.  If you have one of these say Y and read the
          SCSI-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>.

config SCSI_MAC_ESP
        tristate "Macintosh NCR53c9[46] SCSI"
        depends on MAC && SCSI
        help
          This is the NCR 53c9x SCSI controller found on most of the 68040
          based Macintoshes.  If you have one of these say Y and read the
          SCSI-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>.

          To compile this driver as a module, choose M here: the
          module will be called mac_esp.

config MVME147_SCSI
        bool "WD33C93 SCSI driver for MVME147"
        depends on MVME147 && SCSI=y
        help
          Support for the on-board SCSI controller on the Motorola MVME147
          single-board computer.

config MVME16x_SCSI
        bool "NCR53C710 SCSI driver for MVME16x"
        depends on MVME16x && SCSI && BROKEN
        help
          The Motorola MVME162, 166, 167, 172 and 177 boards use the NCR53C710
          SCSI controller chip.  Almost everyone using one of these boards
          will want to say Y to this question.

config BVME6000_SCSI
        bool "NCR53C710 SCSI driver for BVME6000"
        depends on BVME6000 && SCSI && BROKEN
        help
          The BVME4000 and BVME6000 boards from BVM Ltd use the NCR53C710
          SCSI controller chip.  Almost everyone using one of these boards
          will want to say Y to this question.

config SCSI_NCR53C7xx_FAST
        bool "allow FAST-SCSI [10MHz]"
        depends on SCSI_AMIGA7XX || MVME16x_SCSI || BVME6000_SCSI
        help
          This will enable 10MHz FAST-SCSI transfers with your host
          adapter. Some systems have problems with that speed, so it's safest
          to say N here.

config SUN3_SCSI
        tristate "Sun3 NCR5380 SCSI"
        depends on SUN3 && SCSI && BROKEN
        help
          This option will enable support for the OBIO (onboard io) NCR5380
          SCSI controller found in the Sun 3/50 and 3/60, as well as for
          "Sun3" type VME scsi controllers also based on the NCR5380.
          General Linux information on the Sun 3 series (now discontinued)
          is at <http://www.angelfire.com/ca2/tech68k/sun3.html>.

config SUN3X_ESP
        bool "Sun3x ESP SCSI"
        depends on SUN3X && SCSI=y
        help
          The ESP was an on-board SCSI controller used on Sun 3/80
          machines.  Say Y here to compile in support for it.

config SCSI_SUNESP
        tristate "Sparc ESP Scsi Driver"
        depends on SBUS && SCSI
        help
          This is the driver for the Sun ESP SCSI host adapter. The ESP
          chipset is present in most SPARC SBUS-based computers.

          To compile this driver as a module, choose M here: the
          module will be called esp.

#      bool 'Cyberstorm Mk III SCSI support (EXPERIMENTAL)' CONFIG_CYBERSTORMIII_SCSI

config ZFCP
        tristate "FCP host bus adapter driver for IBM eServer zSeries"
        depends on ARCH_S390 && QDIO && SCSI
        select SCSI_FC_ATTRS
        help
          If you want to access SCSI devices attached to your IBM eServer
          zSeries by means of Fibre Channel interfaces say Y.
          For details please refer to the documentation provided by IBM at
          <http://oss.software.ibm.com/developerworks/opensource/linux390>

          This driver is also available as a module. This module will be
          called zfcp. If you want to compile it as a module, say M here
          and read <file:Documentation/modules.txt>.

endmenu

source "drivers/scsi/pcmcia/Kconfig"

endmenu