]> Pileus Git - ~andy/linux/blob - drivers/iio/dac/ad5421.c
staging: rts5208: add support for rts5208 and rts5288
[~andy/linux] / drivers / iio / dac / ad5421.c
1 /*
2  * AD5421 Digital to analog converters  driver
3  *
4  * Copyright 2011 Analog Devices Inc.
5  *
6  * Licensed under the GPL-2.
7  */
8
9 #include <linux/device.h>
10 #include <linux/delay.h>
11 #include <linux/err.h>
12 #include <linux/module.h>
13 #include <linux/interrupt.h>
14 #include <linux/kernel.h>
15 #include <linux/spi/spi.h>
16 #include <linux/slab.h>
17 #include <linux/sysfs.h>
18
19 #include <linux/iio/iio.h>
20 #include <linux/iio/sysfs.h>
21 #include <linux/iio/events.h>
22 #include <linux/iio/dac/ad5421.h>
23
24
25 #define AD5421_REG_DAC_DATA             0x1
26 #define AD5421_REG_CTRL                 0x2
27 #define AD5421_REG_OFFSET               0x3
28 #define AD5421_REG_GAIN                 0x4
29 /* load dac and fault shared the same register number. Writing to it will cause
30  * a dac load command, reading from it will return the fault status register */
31 #define AD5421_REG_LOAD_DAC             0x5
32 #define AD5421_REG_FAULT                0x5
33 #define AD5421_REG_FORCE_ALARM_CURRENT  0x6
34 #define AD5421_REG_RESET                0x7
35 #define AD5421_REG_START_CONVERSION     0x8
36 #define AD5421_REG_NOOP                 0x9
37
38 #define AD5421_CTRL_WATCHDOG_DISABLE    BIT(12)
39 #define AD5421_CTRL_AUTO_FAULT_READBACK BIT(11)
40 #define AD5421_CTRL_MIN_CURRENT         BIT(9)
41 #define AD5421_CTRL_ADC_SOURCE_TEMP     BIT(8)
42 #define AD5421_CTRL_ADC_ENABLE          BIT(7)
43 #define AD5421_CTRL_PWR_DOWN_INT_VREF   BIT(6)
44
45 #define AD5421_FAULT_SPI                        BIT(15)
46 #define AD5421_FAULT_PEC                        BIT(14)
47 #define AD5421_FAULT_OVER_CURRENT               BIT(13)
48 #define AD5421_FAULT_UNDER_CURRENT              BIT(12)
49 #define AD5421_FAULT_TEMP_OVER_140              BIT(11)
50 #define AD5421_FAULT_TEMP_OVER_100              BIT(10)
51 #define AD5421_FAULT_UNDER_VOLTAGE_6V           BIT(9)
52 #define AD5421_FAULT_UNDER_VOLTAGE_12V          BIT(8)
53
54 /* These bits will cause the fault pin to go high */
55 #define AD5421_FAULT_TRIGGER_IRQ \
56         (AD5421_FAULT_SPI | AD5421_FAULT_PEC | AD5421_FAULT_OVER_CURRENT | \
57         AD5421_FAULT_UNDER_CURRENT | AD5421_FAULT_TEMP_OVER_140)
58
59 /**
60  * struct ad5421_state - driver instance specific data
61  * @spi:                spi_device
62  * @ctrl:               control register cache
63  * @current_range:      current range which the device is configured for
64  * @data:               spi transfer buffers
65  * @fault_mask:         software masking of events
66  */
67 struct ad5421_state {
68         struct spi_device               *spi;
69         unsigned int                    ctrl;
70         enum ad5421_current_range       current_range;
71         unsigned int                    fault_mask;
72
73         /*
74          * DMA (thus cache coherency maintenance) requires the
75          * transfer buffers to live in their own cache lines.
76          */
77         union {
78                 u32 d32;
79                 u8 d8[4];
80         } data[2] ____cacheline_aligned;
81 };
82
83 static const struct iio_event_spec ad5421_current_event[] = {
84         {
85                 .type = IIO_EV_TYPE_THRESH,
86                 .dir = IIO_EV_DIR_RISING,
87                 .mask_separate = BIT(IIO_EV_INFO_VALUE) |
88                         BIT(IIO_EV_INFO_ENABLE),
89         }, {
90                 .type = IIO_EV_TYPE_THRESH,
91                 .dir = IIO_EV_DIR_FALLING,
92                 .mask_separate = BIT(IIO_EV_INFO_VALUE) |
93                         BIT(IIO_EV_INFO_ENABLE),
94         },
95 };
96
97 static const struct iio_event_spec ad5421_temp_event[] = {
98         {
99                 .type = IIO_EV_TYPE_THRESH,
100                 .dir = IIO_EV_DIR_RISING,
101                 .mask_separate = BIT(IIO_EV_INFO_VALUE) |
102                         BIT(IIO_EV_INFO_ENABLE),
103         },
104 };
105
106 static const struct iio_chan_spec ad5421_channels[] = {
107         {
108                 .type = IIO_CURRENT,
109                 .indexed = 1,
110                 .output = 1,
111                 .channel = 0,
112                 .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
113                         BIT(IIO_CHAN_INFO_CALIBSCALE) |
114                         BIT(IIO_CHAN_INFO_CALIBBIAS),
115                 .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE) |
116                         BIT(IIO_CHAN_INFO_OFFSET),
117                 .scan_type = IIO_ST('u', 16, 16, 0),
118                 .event_spec = ad5421_current_event,
119                 .num_event_specs = ARRAY_SIZE(ad5421_current_event),
120         },
121         {
122                 .type = IIO_TEMP,
123                 .channel = -1,
124                 .event_spec = ad5421_temp_event,
125                 .num_event_specs = ARRAY_SIZE(ad5421_temp_event),
126         },
127 };
128
129 static int ad5421_write_unlocked(struct iio_dev *indio_dev,
130         unsigned int reg, unsigned int val)
131 {
132         struct ad5421_state *st = iio_priv(indio_dev);
133
134         st->data[0].d32 = cpu_to_be32((reg << 16) | val);
135
136         return spi_write(st->spi, &st->data[0].d8[1], 3);
137 }
138
139 static int ad5421_write(struct iio_dev *indio_dev, unsigned int reg,
140         unsigned int val)
141 {
142         int ret;
143
144         mutex_lock(&indio_dev->mlock);
145         ret = ad5421_write_unlocked(indio_dev, reg, val);
146         mutex_unlock(&indio_dev->mlock);
147
148         return ret;
149 }
150
151 static int ad5421_read(struct iio_dev *indio_dev, unsigned int reg)
152 {
153         struct ad5421_state *st = iio_priv(indio_dev);
154         int ret;
155         struct spi_transfer t[] = {
156                 {
157                         .tx_buf = &st->data[0].d8[1],
158                         .len = 3,
159                         .cs_change = 1,
160                 }, {
161                         .rx_buf = &st->data[1].d8[1],
162                         .len = 3,
163                 },
164         };
165
166         mutex_lock(&indio_dev->mlock);
167
168         st->data[0].d32 = cpu_to_be32((1 << 23) | (reg << 16));
169
170         ret = spi_sync_transfer(st->spi, t, ARRAY_SIZE(t));
171         if (ret >= 0)
172                 ret = be32_to_cpu(st->data[1].d32) & 0xffff;
173
174         mutex_unlock(&indio_dev->mlock);
175
176         return ret;
177 }
178
179 static int ad5421_update_ctrl(struct iio_dev *indio_dev, unsigned int set,
180         unsigned int clr)
181 {
182         struct ad5421_state *st = iio_priv(indio_dev);
183         unsigned int ret;
184
185         mutex_lock(&indio_dev->mlock);
186
187         st->ctrl &= ~clr;
188         st->ctrl |= set;
189
190         ret = ad5421_write_unlocked(indio_dev, AD5421_REG_CTRL, st->ctrl);
191
192         mutex_unlock(&indio_dev->mlock);
193
194         return ret;
195 }
196
197 static irqreturn_t ad5421_fault_handler(int irq, void *data)
198 {
199         struct iio_dev *indio_dev = data;
200         struct ad5421_state *st = iio_priv(indio_dev);
201         unsigned int fault;
202         unsigned int old_fault = 0;
203         unsigned int events;
204
205         fault = ad5421_read(indio_dev, AD5421_REG_FAULT);
206         if (!fault)
207                 return IRQ_NONE;
208
209         /* If we had a fault, this might mean that the DAC has lost its state
210          * and has been reset. Make sure that the control register actually
211          * contains what we expect it to contain. Otherwise the watchdog might
212          * be enabled and we get watchdog timeout faults, which will render the
213          * DAC unusable. */
214         ad5421_update_ctrl(indio_dev, 0, 0);
215
216
217         /* The fault pin stays high as long as a fault condition is present and
218          * it is not possible to mask fault conditions. For certain fault
219          * conditions for example like over-temperature it takes some time
220          * until the fault condition disappears. If we would exit the interrupt
221          * handler immediately after handling the event it would be entered
222          * again instantly. Thus we fall back to polling in case we detect that
223          * a interrupt condition is still present.
224          */
225         do {
226                 /* 0xffff is a invalid value for the register and will only be
227                  * read if there has been a communication error */
228                 if (fault == 0xffff)
229                         fault = 0;
230
231                 /* we are only interested in new events */
232                 events = (old_fault ^ fault) & fault;
233                 events &= st->fault_mask;
234
235                 if (events & AD5421_FAULT_OVER_CURRENT) {
236                         iio_push_event(indio_dev,
237                                 IIO_UNMOD_EVENT_CODE(IIO_CURRENT,
238                                         0,
239                                         IIO_EV_TYPE_THRESH,
240                                         IIO_EV_DIR_RISING),
241                         iio_get_time_ns());
242                 }
243
244                 if (events & AD5421_FAULT_UNDER_CURRENT) {
245                         iio_push_event(indio_dev,
246                                 IIO_UNMOD_EVENT_CODE(IIO_CURRENT,
247                                         0,
248                                         IIO_EV_TYPE_THRESH,
249                                         IIO_EV_DIR_FALLING),
250                                 iio_get_time_ns());
251                 }
252
253                 if (events & AD5421_FAULT_TEMP_OVER_140) {
254                         iio_push_event(indio_dev,
255                                 IIO_UNMOD_EVENT_CODE(IIO_TEMP,
256                                         0,
257                                         IIO_EV_TYPE_MAG,
258                                         IIO_EV_DIR_RISING),
259                                 iio_get_time_ns());
260                 }
261
262                 old_fault = fault;
263                 fault = ad5421_read(indio_dev, AD5421_REG_FAULT);
264
265                 /* still active? go to sleep for some time */
266                 if (fault & AD5421_FAULT_TRIGGER_IRQ)
267                         msleep(1000);
268
269         } while (fault & AD5421_FAULT_TRIGGER_IRQ);
270
271
272         return IRQ_HANDLED;
273 }
274
275 static void ad5421_get_current_min_max(struct ad5421_state *st,
276         unsigned int *min, unsigned int *max)
277 {
278         /* The current range is configured using external pins, which are
279          * usually hard-wired and not run-time switchable. */
280         switch (st->current_range) {
281         case AD5421_CURRENT_RANGE_4mA_20mA:
282                 *min = 4000;
283                 *max = 20000;
284                 break;
285         case AD5421_CURRENT_RANGE_3mA8_21mA:
286                 *min = 3800;
287                 *max = 21000;
288                 break;
289         case AD5421_CURRENT_RANGE_3mA2_24mA:
290                 *min = 3200;
291                 *max = 24000;
292                 break;
293         default:
294                 *min = 0;
295                 *max = 1;
296                 break;
297         }
298 }
299
300 static inline unsigned int ad5421_get_offset(struct ad5421_state *st)
301 {
302         unsigned int min, max;
303
304         ad5421_get_current_min_max(st, &min, &max);
305         return (min * (1 << 16)) / (max - min);
306 }
307
308 static int ad5421_read_raw(struct iio_dev *indio_dev,
309         struct iio_chan_spec const *chan, int *val, int *val2, long m)
310 {
311         struct ad5421_state *st = iio_priv(indio_dev);
312         unsigned int min, max;
313         int ret;
314
315         if (chan->type != IIO_CURRENT)
316                 return -EINVAL;
317
318         switch (m) {
319         case IIO_CHAN_INFO_RAW:
320                 ret = ad5421_read(indio_dev, AD5421_REG_DAC_DATA);
321                 if (ret < 0)
322                         return ret;
323                 *val = ret;
324                 return IIO_VAL_INT;
325         case IIO_CHAN_INFO_SCALE:
326                 ad5421_get_current_min_max(st, &min, &max);
327                 *val = max - min;
328                 *val2 = (1 << 16) * 1000;
329                 return IIO_VAL_FRACTIONAL;
330         case IIO_CHAN_INFO_OFFSET:
331                 *val = ad5421_get_offset(st);
332                 return IIO_VAL_INT;
333         case IIO_CHAN_INFO_CALIBBIAS:
334                 ret = ad5421_read(indio_dev, AD5421_REG_OFFSET);
335                 if (ret < 0)
336                         return ret;
337                 *val = ret - 32768;
338                 return IIO_VAL_INT;
339         case IIO_CHAN_INFO_CALIBSCALE:
340                 ret = ad5421_read(indio_dev, AD5421_REG_GAIN);
341                 if (ret < 0)
342                         return ret;
343                 *val = ret;
344                 return IIO_VAL_INT;
345         }
346
347         return -EINVAL;
348 }
349
350 static int ad5421_write_raw(struct iio_dev *indio_dev,
351         struct iio_chan_spec const *chan, int val, int val2, long mask)
352 {
353         const unsigned int max_val = 1 << 16;
354
355         switch (mask) {
356         case IIO_CHAN_INFO_RAW:
357                 if (val >= max_val || val < 0)
358                         return -EINVAL;
359
360                 return ad5421_write(indio_dev, AD5421_REG_DAC_DATA, val);
361         case IIO_CHAN_INFO_CALIBBIAS:
362                 val += 32768;
363                 if (val >= max_val || val < 0)
364                         return -EINVAL;
365
366                 return ad5421_write(indio_dev, AD5421_REG_OFFSET, val);
367         case IIO_CHAN_INFO_CALIBSCALE:
368                 if (val >= max_val || val < 0)
369                         return -EINVAL;
370
371                 return ad5421_write(indio_dev, AD5421_REG_GAIN, val);
372         default:
373                 break;
374         }
375
376         return -EINVAL;
377 }
378
379 static int ad5421_write_event_config(struct iio_dev *indio_dev,
380         const struct iio_chan_spec *chan, enum iio_event_type type,
381         enum iio_event_direction dir, int state)
382 {
383         struct ad5421_state *st = iio_priv(indio_dev);
384         unsigned int mask;
385
386         switch (chan->type) {
387         case IIO_CURRENT:
388                 if (dir == IIO_EV_DIR_RISING)
389                         mask = AD5421_FAULT_OVER_CURRENT;
390                 else
391                         mask = AD5421_FAULT_UNDER_CURRENT;
392                 break;
393         case IIO_TEMP:
394                 mask = AD5421_FAULT_TEMP_OVER_140;
395                 break;
396         default:
397                 return -EINVAL;
398         }
399
400         mutex_lock(&indio_dev->mlock);
401         if (state)
402                 st->fault_mask |= mask;
403         else
404                 st->fault_mask &= ~mask;
405         mutex_unlock(&indio_dev->mlock);
406
407         return 0;
408 }
409
410 static int ad5421_read_event_config(struct iio_dev *indio_dev,
411         const struct iio_chan_spec *chan, enum iio_event_type type,
412         enum iio_event_direction dir)
413 {
414         struct ad5421_state *st = iio_priv(indio_dev);
415         unsigned int mask;
416
417         switch (chan->type) {
418         case IIO_CURRENT:
419                 if (dir == IIO_EV_DIR_RISING)
420                         mask = AD5421_FAULT_OVER_CURRENT;
421                 else
422                         mask = AD5421_FAULT_UNDER_CURRENT;
423                 break;
424         case IIO_TEMP:
425                 mask = AD5421_FAULT_TEMP_OVER_140;
426                 break;
427         default:
428                 return -EINVAL;
429         }
430
431         return (bool)(st->fault_mask & mask);
432 }
433
434 static int ad5421_read_event_value(struct iio_dev *indio_dev,
435         const struct iio_chan_spec *chan, enum iio_event_type type,
436         enum iio_event_direction dir, enum iio_event_info info, int *val,
437         int *val2)
438 {
439         int ret;
440
441         switch (chan->type) {
442         case IIO_CURRENT:
443                 ret = ad5421_read(indio_dev, AD5421_REG_DAC_DATA);
444                 if (ret < 0)
445                         return ret;
446                 *val = ret;
447                 break;
448         case IIO_TEMP:
449                 *val = 140000;
450                 break;
451         default:
452                 return -EINVAL;
453         }
454
455         return IIO_VAL_INT;
456 }
457
458 static const struct iio_info ad5421_info = {
459         .read_raw =             ad5421_read_raw,
460         .write_raw =            ad5421_write_raw,
461         .read_event_config_new = ad5421_read_event_config,
462         .write_event_config_new = ad5421_write_event_config,
463         .read_event_value_new = ad5421_read_event_value,
464         .driver_module =        THIS_MODULE,
465 };
466
467 static int ad5421_probe(struct spi_device *spi)
468 {
469         struct ad5421_platform_data *pdata = dev_get_platdata(&spi->dev);
470         struct iio_dev *indio_dev;
471         struct ad5421_state *st;
472         int ret;
473
474         indio_dev = devm_iio_device_alloc(&spi->dev, sizeof(*st));
475         if (indio_dev == NULL) {
476                 dev_err(&spi->dev, "Failed to allocate iio device\n");
477                 return  -ENOMEM;
478         }
479
480         st = iio_priv(indio_dev);
481         spi_set_drvdata(spi, indio_dev);
482
483         st->spi = spi;
484
485         indio_dev->dev.parent = &spi->dev;
486         indio_dev->name = "ad5421";
487         indio_dev->info = &ad5421_info;
488         indio_dev->modes = INDIO_DIRECT_MODE;
489         indio_dev->channels = ad5421_channels;
490         indio_dev->num_channels = ARRAY_SIZE(ad5421_channels);
491
492         st->ctrl = AD5421_CTRL_WATCHDOG_DISABLE |
493                         AD5421_CTRL_AUTO_FAULT_READBACK;
494
495         if (pdata) {
496                 st->current_range = pdata->current_range;
497                 if (pdata->external_vref)
498                         st->ctrl |= AD5421_CTRL_PWR_DOWN_INT_VREF;
499         } else {
500                 st->current_range = AD5421_CURRENT_RANGE_4mA_20mA;
501         }
502
503         /* write initial ctrl register value */
504         ad5421_update_ctrl(indio_dev, 0, 0);
505
506         if (spi->irq) {
507                 ret = devm_request_threaded_irq(&spi->dev, spi->irq,
508                                            NULL,
509                                            ad5421_fault_handler,
510                                            IRQF_TRIGGER_HIGH | IRQF_ONESHOT,
511                                            "ad5421 fault",
512                                            indio_dev);
513                 if (ret)
514                         return ret;
515         }
516
517         return iio_device_register(indio_dev);
518 }
519
520 static int ad5421_remove(struct spi_device *spi)
521 {
522         struct iio_dev *indio_dev = spi_get_drvdata(spi);
523
524         iio_device_unregister(indio_dev);
525
526         return 0;
527 }
528
529 static struct spi_driver ad5421_driver = {
530         .driver = {
531                    .name = "ad5421",
532                    .owner = THIS_MODULE,
533         },
534         .probe = ad5421_probe,
535         .remove = ad5421_remove,
536 };
537 module_spi_driver(ad5421_driver);
538
539 MODULE_AUTHOR("Lars-Peter Clausen <lars@metafoo.de>");
540 MODULE_DESCRIPTION("Analog Devices AD5421 DAC");
541 MODULE_LICENSE("GPL v2");
542 MODULE_ALIAS("spi:ad5421");