Pileus Git - ~andy/linux/blob - arch/arm/mach-omap2/vc.c

   1 /*
   2  * OMAP Voltage Controller (VC) interface
   3  *
   4  * Copyright (C) 2011 Texas Instruments, Inc.
   5  *
   6  * This file is licensed under the terms of the GNU General Public
   7  * License version 2. This program is licensed "as is" without any
   8  * warranty of any kind, whether express or implied.
   9  */
  10 #include <linux/kernel.h>
  11 #include <linux/delay.h>
  12 #include <linux/init.h>
  13
  14 #include <plat/cpu.h>
  15
  16 #include "voltage.h"
  17 #include "vc.h"
  18 #include "prm-regbits-34xx.h"
  19 #include "prm-regbits-44xx.h"
  20 #include "prm44xx.h"
  21
  22 /**
  23  * struct omap_vc_channel_cfg - describe the cfg_channel bitfield
  24  * @sa: bit for slave address
  25  * @rav: bit for voltage configuration register
  26  * @rac: bit for command configuration register
  27  * @racen: enable bit for RAC
  28  * @cmd: bit for command value set selection
  29  *
  30  * Channel configuration bits, common for OMAP3+
  31  * OMAP3 register: PRM_VC_CH_CONF
  32  * OMAP4 register: PRM_VC_CFG_CHANNEL
  33  * OMAP5 register: PRM_VC_SMPS_<voltdm>_CONFIG
  34  */
  35 struct omap_vc_channel_cfg {
  36         u8 sa;
  37         u8 rav;
  38         u8 rac;
  39         u8 racen;
  40         u8 cmd;
  41 };
  42
  43 static struct omap_vc_channel_cfg vc_default_channel_cfg = {
  44         .sa    = BIT(0),
  45         .rav   = BIT(1),
  46         .rac   = BIT(2),
  47         .racen = BIT(3),
  48         .cmd   = BIT(4),
  49 };
  50
  51 /*
  52  * On OMAP3+, all VC channels have the above default bitfield
  53  * configuration, except the OMAP4 MPU channel.  This appears
  54  * to be a freak accident as every other VC channel has the
  55  * default configuration, thus creating a mutant channel config.
  56  */
  57 static struct omap_vc_channel_cfg vc_mutant_channel_cfg = {
  58         .sa    = BIT(0),
  59         .rav   = BIT(2),
  60         .rac   = BIT(3),
  61         .racen = BIT(4),
  62         .cmd   = BIT(1),
  63 };
  64
  65 static struct omap_vc_channel_cfg *vc_cfg_bits;
  66 #define CFG_CHANNEL_MASK 0x1f
  67
  68 /**
  69  * omap_vc_config_channel - configure VC channel to PMIC mappings
  70  * @voltdm: pointer to voltagdomain defining the desired VC channel
  71  *
  72  * Configures the VC channel to PMIC mappings for the following
  73  * PMIC settings
  74  * - i2c slave address (SA)
  75  * - voltage configuration address (RAV)
  76  * - command configuration address (RAC) and enable bit (RACEN)
  77  * - command values for ON, ONLP, RET and OFF (CMD)
  78  *
  79  * This function currently only allows flexible configuration of the
  80  * non-default channel.  Starting with OMAP4, there are more than 2
  81  * channels, with one defined as the default (on OMAP4, it's MPU.)
  82  * Only the non-default channel can be configured.
  83  */
  84 static int omap_vc_config_channel(struct voltagedomain *voltdm)
  85 {
  86         struct omap_vc_channel *vc = voltdm->vc;
  87
  88         /*
  89          * For default channel, the only configurable bit is RACEN.
  90          * All others must stay at zero (see function comment above.)
  91          */
  92         if (vc->flags & OMAP_VC_CHANNEL_DEFAULT)
  93                 vc->cfg_channel &= vc_cfg_bits->racen;
  94
  95         voltdm->rmw(CFG_CHANNEL_MASK << vc->cfg_channel_sa_shift,
  96                     vc->cfg_channel << vc->cfg_channel_sa_shift,
  97                     vc->common->cfg_channel_reg);
  98
  99         return 0;
 100 }
 101
 102 /* Voltage scale and accessory APIs */
 103 int omap_vc_pre_scale(struct voltagedomain *voltdm,
 104                       unsigned long target_volt,
 105                       u8 *target_vsel, u8 *current_vsel)
 106 {
 107         struct omap_vc_channel *vc = voltdm->vc;
 108         struct omap_vdd_info *vdd = voltdm->vdd;
 109         struct omap_volt_data *volt_data;
 110         const struct omap_vp_common_data *vp_common;
 111         u32 vc_cmdval, vp_errgain_val;
 112
 113         vp_common = vdd->vp_data->vp_common;
 114
 115         /* Check if sufficient pmic info is available for this vdd */
 116         if (!voltdm->pmic) {
 117                 pr_err("%s: Insufficient pmic info to scale the vdd_%s\n",
 118                         __func__, voltdm->name);
 119                 return -EINVAL;
 120         }
 121
 122         if (!voltdm->pmic->uv_to_vsel) {
 123                 pr_err("%s: PMIC function to convert voltage in uV to"
 124                         "vsel not registered. Hence unable to scale voltage"
 125                         "for vdd_%s\n", __func__, voltdm->name);
 126                 return -ENODATA;
 127         }
 128
 129         if (!voltdm->read || !voltdm->write) {
 130                 pr_err("%s: No read/write API for accessing vdd_%s regs\n",
 131                         __func__, voltdm->name);
 132                 return -EINVAL;
 133         }
 134
 135         /* Get volt_data corresponding to target_volt */
 136         volt_data = omap_voltage_get_voltdata(voltdm, target_volt);
 137         if (IS_ERR(volt_data))
 138                 volt_data = NULL;
 139
 140         *target_vsel = voltdm->pmic->uv_to_vsel(target_volt);
 141         *current_vsel = voltdm->read(vdd->vp_data->voltage);
 142
 143         /* Setting the ON voltage to the new target voltage */
 144         vc_cmdval = voltdm->read(vc->cmdval_reg);
 145         vc_cmdval &= ~vc->common->cmd_on_mask;
 146         vc_cmdval |= (*target_vsel << vc->common->cmd_on_shift);
 147         voltdm->write(vc_cmdval, vc->cmdval_reg);
 148
 149         /* Setting vp errorgain based on the voltage */
 150         if (volt_data) {
 151                 vp_errgain_val = voltdm->read(vdd->vp_data->vpconfig);
 152                 vdd->vp_rt_data.vpconfig_errorgain = volt_data->vp_errgain;
 153                 vp_errgain_val &= ~vp_common->vpconfig_errorgain_mask;
 154                 vp_errgain_val |= vdd->vp_rt_data.vpconfig_errorgain <<
 155                         vp_common->vpconfig_errorgain_shift;
 156                 voltdm->write(vp_errgain_val, vdd->vp_data->vpconfig);
 157         }
 158
 159         return 0;
 160 }
 161
 162 void omap_vc_post_scale(struct voltagedomain *voltdm,
 163                         unsigned long target_volt,
 164                         u8 target_vsel, u8 current_vsel)
 165 {
 166         struct omap_vdd_info *vdd = voltdm->vdd;
 167         u32 smps_steps = 0, smps_delay = 0;
 168
 169         smps_steps = abs(target_vsel - current_vsel);
 170         /* SMPS slew rate / step size. 2us added as buffer. */
 171         smps_delay = ((smps_steps * voltdm->pmic->step_size) /
 172                         voltdm->pmic->slew_rate) + 2;
 173         udelay(smps_delay);
 174
 175         vdd->curr_volt = target_volt;
 176 }
 177
 178 /* vc_bypass_scale - VC bypass method of voltage scaling */
 179 int omap_vc_bypass_scale(struct voltagedomain *voltdm,
 180                          unsigned long target_volt)
 181 {
 182         struct omap_vc_channel *vc = voltdm->vc;
 183         u32 loop_cnt = 0, retries_cnt = 0;
 184         u32 vc_valid, vc_bypass_val_reg, vc_bypass_value;
 185         u8 target_vsel, current_vsel;
 186         int ret;
 187
 188         ret = omap_vc_pre_scale(voltdm, target_volt, &target_vsel, &current_vsel);
 189         if (ret)
 190                 return ret;
 191
 192         vc_valid = vc->common->valid;
 193         vc_bypass_val_reg = vc->common->bypass_val_reg;
 194         vc_bypass_value = (target_vsel << vc->common->data_shift) |
 195                 (vc->volt_reg_addr << vc->common->regaddr_shift) |
 196                 (vc->i2c_slave_addr << vc->common->slaveaddr_shift);
 197
 198         voltdm->write(vc_bypass_value, vc_bypass_val_reg);
 199         voltdm->write(vc_bypass_value | vc_valid, vc_bypass_val_reg);
 200
 201         vc_bypass_value = voltdm->read(vc_bypass_val_reg);
 202         /*
 203          * Loop till the bypass command is acknowledged from the SMPS.
 204          * NOTE: This is legacy code. The loop count and retry count needs
 205          * to be revisited.
 206          */
 207         while (!(vc_bypass_value & vc_valid)) {
 208                 loop_cnt++;
 209
 210                 if (retries_cnt > 10) {
 211                         pr_warning("%s: Retry count exceeded\n", __func__);
 212                         return -ETIMEDOUT;
 213                 }
 214
 215                 if (loop_cnt > 50) {
 216                         retries_cnt++;
 217                         loop_cnt = 0;
 218                         udelay(10);
 219                 }
 220                 vc_bypass_value = voltdm->read(vc_bypass_val_reg);
 221         }
 222
 223         omap_vc_post_scale(voltdm, target_volt, target_vsel, current_vsel);
 224         return 0;
 225 }
 226
 227 static void __init omap3_vfsm_init(struct voltagedomain *voltdm)
 228 {
 229         /*
 230          * Voltage Manager FSM parameters init
 231          * XXX This data should be passed in from the board file
 232          */
 233         voltdm->write(OMAP3_CLKSETUP, OMAP3_PRM_CLKSETUP_OFFSET);
 234         voltdm->write(OMAP3_VOLTOFFSET, OMAP3_PRM_VOLTOFFSET_OFFSET);
 235         voltdm->write(OMAP3_VOLTSETUP2, OMAP3_PRM_VOLTSETUP2_OFFSET);
 236 }
 237
 238 static void __init omap3_vc_init_channel(struct voltagedomain *voltdm)
 239 {
 240         static bool is_initialized;
 241
 242         if (is_initialized)
 243                 return;
 244
 245         omap3_vfsm_init(voltdm);
 246
 247         is_initialized = true;
 248 }
 249
 250
 251 /* OMAP4 specific voltage init functions */
 252 static void __init omap4_vc_init_channel(struct voltagedomain *voltdm)
 253 {
 254         static bool is_initialized;
 255         u32 vc_val;
 256
 257         if (is_initialized)
 258                 return;
 259
 260         /* XXX These are magic numbers and do not belong! */
 261         vc_val = (0x60 << OMAP4430_SCLL_SHIFT | 0x26 << OMAP4430_SCLH_SHIFT);
 262         voltdm->write(vc_val, OMAP4_PRM_VC_CFG_I2C_CLK_OFFSET);
 263
 264         is_initialized = true;
 265 }
 266
 267 /**
 268  * omap_vc_i2c_init - initialize I2C interface to PMIC
 269  * @voltdm: voltage domain containing VC data
 270  *
 271  * Use PMIC supplied seetings for I2C high-speed mode and
 272  * master code (if set) and program the VC I2C configuration
 273  * register.
 274  *
 275  * The VC I2C configuration is common to all VC channels,
 276  * so this function only configures I2C for the first VC
 277  * channel registers.  All other VC channels will use the
 278  * same configuration.
 279  */
 280 static void __init omap_vc_i2c_init(struct voltagedomain *voltdm)
 281 {
 282         struct omap_vc_channel *vc = voltdm->vc;
 283         static bool initialized;
 284         static bool i2c_high_speed;
 285         u8 mcode;
 286
 287         if (initialized) {
 288                 if (voltdm->pmic->i2c_high_speed != i2c_high_speed)
 289                         pr_warn("%s: I2C config for all channels must match.",
 290                                 __func__);
 291                 return;
 292         }
 293
 294         i2c_high_speed = voltdm->pmic->i2c_high_speed;
 295         if (i2c_high_speed)
 296                 voltdm->rmw(vc->common->i2c_cfg_hsen_mask,
 297                             vc->common->i2c_cfg_hsen_mask,
 298                             vc->common->i2c_cfg_reg);
 299
 300         mcode = voltdm->pmic->i2c_mcode;
 301         if (mcode)
 302                 voltdm->rmw(vc->common->i2c_mcode_mask,
 303                             mcode << __ffs(vc->common->i2c_mcode_mask),
 304                             vc->common->i2c_cfg_reg);
 305
 306         initialized = true;
 307 }
 308
 309 void __init omap_vc_init_channel(struct voltagedomain *voltdm)
 310 {
 311         struct omap_vc_channel *vc = voltdm->vc;
 312         u8 on_vsel, onlp_vsel, ret_vsel, off_vsel;
 313         u32 val;
 314
 315         if (!voltdm->pmic || !voltdm->pmic->uv_to_vsel) {
 316                 pr_err("%s: PMIC info requried to configure vc for"
 317                         "vdd_%s not populated.Hence cannot initialize vc\n",
 318                         __func__, voltdm->name);
 319                 return;
 320         }
 321
 322         if (!voltdm->read || !voltdm->write) {
 323                 pr_err("%s: No read/write API for accessing vdd_%s regs\n",
 324                         __func__, voltdm->name);
 325                 return;
 326         }
 327
 328         vc->cfg_channel = 0;
 329         if (vc->flags & OMAP_VC_CHANNEL_CFG_MUTANT)
 330                 vc_cfg_bits = &vc_mutant_channel_cfg;
 331         else
 332                 vc_cfg_bits = &vc_default_channel_cfg;
 333
 334         /* get PMIC/board specific settings */
 335         vc->i2c_slave_addr = voltdm->pmic->i2c_slave_addr;
 336         vc->volt_reg_addr = voltdm->pmic->volt_reg_addr;
 337         vc->cmd_reg_addr = voltdm->pmic->cmd_reg_addr;
 338         vc->setup_time = voltdm->pmic->volt_setup_time;
 339
 340         /* Configure the i2c slave address for this VC */
 341         voltdm->rmw(vc->smps_sa_mask,
 342                     vc->i2c_slave_addr << __ffs(vc->smps_sa_mask),
 343                     vc->common->smps_sa_reg);
 344         vc->cfg_channel |= vc_cfg_bits->sa;
 345
 346         /*
 347          * Configure the PMIC register addresses.
 348          */
 349         voltdm->rmw(vc->smps_volra_mask,
 350                     vc->volt_reg_addr << __ffs(vc->smps_volra_mask),
 351                     vc->common->smps_volra_reg);
 352         vc->cfg_channel |= vc_cfg_bits->rav;
 353
 354         if (vc->cmd_reg_addr) {
 355                 voltdm->rmw(vc->smps_cmdra_mask,
 356                             vc->cmd_reg_addr << __ffs(vc->smps_cmdra_mask),
 357                             vc->common->smps_cmdra_reg);
 358                 vc->cfg_channel |= vc_cfg_bits->rac | vc_cfg_bits->racen;
 359         }
 360
 361         /* Set up the on, inactive, retention and off voltage */
 362         on_vsel = voltdm->pmic->uv_to_vsel(voltdm->pmic->on_volt);
 363         onlp_vsel = voltdm->pmic->uv_to_vsel(voltdm->pmic->onlp_volt);
 364         ret_vsel = voltdm->pmic->uv_to_vsel(voltdm->pmic->ret_volt);
 365         off_vsel = voltdm->pmic->uv_to_vsel(voltdm->pmic->off_volt);
 366         val = ((on_vsel << vc->common->cmd_on_shift) |
 367                (onlp_vsel << vc->common->cmd_onlp_shift) |
 368                (ret_vsel << vc->common->cmd_ret_shift) |
 369                (off_vsel << vc->common->cmd_off_shift));
 370         voltdm->write(val, vc->cmdval_reg);
 371         vc->cfg_channel |= vc_cfg_bits->cmd;
 372
 373         /* Channel configuration */
 374         omap_vc_config_channel(voltdm);
 375
 376         /* Configure the setup times */
 377         voltdm->rmw(voltdm->vfsm->voltsetup_mask,
 378                     vc->setup_time << __ffs(voltdm->vfsm->voltsetup_mask),
 379                     voltdm->vfsm->voltsetup_reg);
 380
 381         omap_vc_i2c_init(voltdm);
 382
 383         if (cpu_is_omap34xx())
 384                 omap3_vc_init_channel(voltdm);
 385         else if (cpu_is_omap44xx())
 386                 omap4_vc_init_channel(voltdm);
 387 }
 388