2 * linux/arch/arm/mach-omap2/board-omap3beagle.c
4 * Copyright (C) 2008 Texas Instruments
6 * Modified from mach-omap2/board-3430sdp.c
8 * Initial code: Syed Mohammed Khasim
10 * This program is free software; you can redistribute it and/or modify
11 * it under the terms of the GNU General Public License version 2 as
12 * published by the Free Software Foundation.
15 #include <linux/kernel.h>
16 #include <linux/init.h>
17 #include <linux/platform_device.h>
18 #include <linux/delay.h>
19 #include <linux/err.h>
20 #include <linux/clk.h>
22 #include <linux/leds.h>
23 #include <linux/gpio.h>
24 #include <linux/input.h>
25 #include <linux/gpio_keys.h>
26 #include <linux/opp.h>
28 #include <linux/mtd/mtd.h>
29 #include <linux/mtd/partitions.h>
30 #include <linux/mtd/nand.h>
31 #include <linux/mmc/host.h>
33 #include <linux/regulator/machine.h>
34 #include <linux/i2c/twl.h>
36 #include <mach/hardware.h>
37 #include <asm/mach-types.h>
38 #include <asm/mach/arch.h>
39 #include <asm/mach/map.h>
40 #include <asm/mach/flash.h>
42 #include <plat/board.h>
44 #include <video/omapdss.h>
45 #include <video/omap-panel-tfp410.h>
46 #include <plat/gpmc.h>
47 #include <plat/nand.h>
49 #include <plat/omap_device.h>
54 #include "common-board-devices.h"
57 * OMAP3 Beagle revision
58 * Run time detection of Beagle revision is done by reading GPIO.
60 * AXBX = GPIO173, GPIO172, GPIO171: 1 1 1
61 * C1_3 = GPIO173, GPIO172, GPIO171: 1 1 0
62 * C4 = GPIO173, GPIO172, GPIO171: 1 0 1
63 * XMA/XMB = GPIO173, GPIO172, GPIO171: 0 0 0
64 * XMC = GPIO173, GPIO172, GPIO171: 0 1 0
67 OMAP3BEAGLE_BOARD_UNKN = 0,
68 OMAP3BEAGLE_BOARD_AXBX,
69 OMAP3BEAGLE_BOARD_C1_3,
72 OMAP3BEAGLE_BOARD_XMC,
75 static u8 omap3_beagle_version;
78 * Board-specific configuration
79 * Defaults to BeagleBoard-xMC
88 .mmc1_gpio_wp = -EINVAL,
89 .usb_pwr_level = GPIOF_OUT_INIT_LOW,
92 .mmc_caps = MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
95 static struct gpio omap3_beagle_rev_gpios[] __initdata = {
96 { 171, GPIOF_IN, "rev_id_0" },
97 { 172, GPIOF_IN, "rev_id_1" },
98 { 173, GPIOF_IN, "rev_id_2" },
101 static void __init omap3_beagle_init_rev(void)
106 omap_mux_init_gpio(171, OMAP_PIN_INPUT_PULLUP);
107 omap_mux_init_gpio(172, OMAP_PIN_INPUT_PULLUP);
108 omap_mux_init_gpio(173, OMAP_PIN_INPUT_PULLUP);
110 ret = gpio_request_array(omap3_beagle_rev_gpios,
111 ARRAY_SIZE(omap3_beagle_rev_gpios));
113 printk(KERN_ERR "Unable to get revision detection GPIO pins\n");
114 omap3_beagle_version = OMAP3BEAGLE_BOARD_UNKN;
118 beagle_rev = gpio_get_value(171) | (gpio_get_value(172) << 1)
119 | (gpio_get_value(173) << 2);
121 gpio_free_array(omap3_beagle_rev_gpios,
122 ARRAY_SIZE(omap3_beagle_rev_gpios));
124 switch (beagle_rev) {
126 printk(KERN_INFO "OMAP3 Beagle Rev: Ax/Bx\n");
127 omap3_beagle_version = OMAP3BEAGLE_BOARD_AXBX;
128 beagle_config.mmc1_gpio_wp = 29;
129 beagle_config.reset_gpio = 170;
130 beagle_config.usr_button_gpio = 7;
133 printk(KERN_INFO "OMAP3 Beagle Rev: C1/C2/C3\n");
134 omap3_beagle_version = OMAP3BEAGLE_BOARD_C1_3;
135 beagle_config.mmc1_gpio_wp = 23;
136 beagle_config.reset_gpio = 170;
137 beagle_config.usr_button_gpio = 7;
140 printk(KERN_INFO "OMAP3 Beagle Rev: C4\n");
141 omap3_beagle_version = OMAP3BEAGLE_BOARD_C4;
142 beagle_config.mmc1_gpio_wp = 23;
143 beagle_config.reset_gpio = 170;
144 beagle_config.usr_button_gpio = 7;
147 printk(KERN_INFO "OMAP3 Beagle Rev: xM Ax/Bx\n");
148 omap3_beagle_version = OMAP3BEAGLE_BOARD_XM;
149 beagle_config.usb_pwr_level = GPIOF_OUT_INIT_HIGH;
150 beagle_config.mmc_caps &= ~MMC_CAP_8_BIT_DATA;
153 printk(KERN_INFO "OMAP3 Beagle Rev: xM C\n");
154 omap3_beagle_version = OMAP3BEAGLE_BOARD_XMC;
155 beagle_config.mmc_caps &= ~MMC_CAP_8_BIT_DATA;
158 printk(KERN_INFO "OMAP3 Beagle Rev: unknown %hd\n", beagle_rev);
159 omap3_beagle_version = OMAP3BEAGLE_BOARD_UNKN;
163 static struct mtd_partition omap3beagle_nand_partitions[] = {
164 /* All the partition sizes are listed in terms of NAND block size */
168 .size = 4 * NAND_BLOCK_SIZE,
169 .mask_flags = MTD_WRITEABLE, /* force read-only */
173 .offset = MTDPART_OFS_APPEND, /* Offset = 0x80000 */
174 .size = 15 * NAND_BLOCK_SIZE,
175 .mask_flags = MTD_WRITEABLE, /* force read-only */
178 .name = "U-Boot Env",
179 .offset = MTDPART_OFS_APPEND, /* Offset = 0x260000 */
180 .size = 1 * NAND_BLOCK_SIZE,
184 .offset = MTDPART_OFS_APPEND, /* Offset = 0x280000 */
185 .size = 32 * NAND_BLOCK_SIZE,
188 .name = "File System",
189 .offset = MTDPART_OFS_APPEND, /* Offset = 0x680000 */
190 .size = MTDPART_SIZ_FULL,
196 static struct tfp410_platform_data dvi_panel = {
198 .power_down_gpio = -1,
201 static struct omap_dss_device beagle_dvi_device = {
202 .type = OMAP_DISPLAY_TYPE_DPI,
204 .driver_name = "tfp410",
206 .phy.dpi.data_lines = 24,
209 static struct omap_dss_device beagle_tv_device = {
211 .driver_name = "venc",
212 .type = OMAP_DISPLAY_TYPE_VENC,
213 .phy.venc.type = OMAP_DSS_VENC_TYPE_SVIDEO,
216 static struct omap_dss_device *beagle_dss_devices[] = {
221 static struct omap_dss_board_info beagle_dss_data = {
222 .num_devices = ARRAY_SIZE(beagle_dss_devices),
223 .devices = beagle_dss_devices,
224 .default_device = &beagle_dvi_device,
227 #include "sdram-micron-mt46h32m32lf-6.h"
229 static struct omap2_hsmmc_info mmc[] = {
232 .caps = MMC_CAP_4_BIT_DATA,
239 static struct regulator_consumer_supply beagle_vmmc1_supply[] = {
240 REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
243 static struct regulator_consumer_supply beagle_vsim_supply[] = {
244 REGULATOR_SUPPLY("vmmc_aux", "omap_hsmmc.0"),
247 static struct gpio_led gpio_leds[];
249 static int beagle_twl_gpio_setup(struct device *dev,
250 unsigned gpio, unsigned ngpio)
254 mmc[0].gpio_wp = beagle_config.mmc1_gpio_wp;
255 /* gpio + 0 is "mmc0_cd" (input/IRQ) */
256 mmc[0].gpio_cd = gpio + 0;
257 omap_hsmmc_late_init(mmc);
260 * TWL4030_GPIO_MAX + 0 == ledA, EHCI nEN_USB_PWR (out, XM active
261 * high / others active low)
262 * DVI reset GPIO is different between beagle revisions
264 /* Valid for all -xM revisions */
265 if (cpu_is_omap3630()) {
267 * gpio + 1 on Xm controls the TFP410's enable line (active low)
268 * gpio + 2 control varies depending on the board rev as below:
269 * P7/P8 revisions(prototype): Camera EN
270 * A2+ revisions (production): LDO (DVI, serial, led blocks)
272 r = gpio_request_one(gpio + 1, GPIOF_OUT_INIT_LOW,
275 pr_err("%s: unable to configure nDVI_PWR_EN\n",
277 r = gpio_request_one(gpio + 2, GPIOF_OUT_INIT_HIGH,
280 pr_err("%s: unable to configure DVI_LDO_EN\n",
284 * REVISIT: need ehci-omap hooks for external VBUS
285 * power switch and overcurrent detect
287 if (gpio_request_one(gpio + 1, GPIOF_IN, "EHCI_nOC"))
288 pr_err("%s: unable to configure EHCI_nOC\n", __func__);
290 dvi_panel.power_down_gpio = beagle_config.reset_gpio;
292 gpio_request_one(gpio + TWL4030_GPIO_MAX, beagle_config.usb_pwr_level,
295 /* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
296 gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
301 static struct twl4030_gpio_platform_data beagle_gpio_data = {
302 .gpio_base = OMAP_MAX_GPIO_LINES,
303 .irq_base = TWL4030_GPIO_IRQ_BASE,
304 .irq_end = TWL4030_GPIO_IRQ_END,
307 .pulldowns = BIT(2) | BIT(6) | BIT(7) | BIT(8) | BIT(13)
308 | BIT(15) | BIT(16) | BIT(17),
309 .setup = beagle_twl_gpio_setup,
312 /* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
313 static struct regulator_init_data beagle_vmmc1 = {
317 .valid_modes_mask = REGULATOR_MODE_NORMAL
318 | REGULATOR_MODE_STANDBY,
319 .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
320 | REGULATOR_CHANGE_MODE
321 | REGULATOR_CHANGE_STATUS,
323 .num_consumer_supplies = ARRAY_SIZE(beagle_vmmc1_supply),
324 .consumer_supplies = beagle_vmmc1_supply,
327 /* VSIM for MMC1 pins DAT4..DAT7 (2 mA, plus card == max 50 mA) */
328 static struct regulator_init_data beagle_vsim = {
332 .valid_modes_mask = REGULATOR_MODE_NORMAL
333 | REGULATOR_MODE_STANDBY,
334 .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
335 | REGULATOR_CHANGE_MODE
336 | REGULATOR_CHANGE_STATUS,
338 .num_consumer_supplies = ARRAY_SIZE(beagle_vsim_supply),
339 .consumer_supplies = beagle_vsim_supply,
342 static struct twl4030_platform_data beagle_twldata = {
343 /* platform_data for children goes here */
344 .gpio = &beagle_gpio_data,
345 .vmmc1 = &beagle_vmmc1,
346 .vsim = &beagle_vsim,
349 static struct i2c_board_info __initdata beagle_i2c_eeprom[] = {
351 I2C_BOARD_INFO("eeprom", 0x50),
355 static int __init omap3_beagle_i2c_init(void)
357 omap3_pmic_get_config(&beagle_twldata,
358 TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_MADC |
359 TWL_COMMON_PDATA_AUDIO,
360 TWL_COMMON_REGULATOR_VDAC | TWL_COMMON_REGULATOR_VPLL2);
362 beagle_twldata.vpll2->constraints.name = "VDVI";
364 omap3_pmic_init("twl4030", &beagle_twldata);
365 /* Bus 3 is attached to the DVI port where devices like the pico DLP
366 * projector don't work reliably with 400kHz */
367 omap_register_i2c_bus(3, 100, beagle_i2c_eeprom, ARRAY_SIZE(beagle_i2c_eeprom));
371 static struct gpio_led gpio_leds[] = {
373 .name = "beagleboard::usr0",
374 .default_trigger = "heartbeat",
378 .name = "beagleboard::usr1",
379 .default_trigger = "mmc0",
383 .name = "beagleboard::pmu_stat",
384 .gpio = -EINVAL, /* gets replaced */
389 static struct gpio_led_platform_data gpio_led_info = {
391 .num_leds = ARRAY_SIZE(gpio_leds),
394 static struct platform_device leds_gpio = {
398 .platform_data = &gpio_led_info,
402 static struct gpio_keys_button gpio_buttons[] = {
405 /* Dynamically assigned depending on board */
412 static struct gpio_keys_platform_data gpio_key_info = {
413 .buttons = gpio_buttons,
414 .nbuttons = ARRAY_SIZE(gpio_buttons),
417 static struct platform_device keys_gpio = {
421 .platform_data = &gpio_key_info,
425 static struct platform_device madc_hwmon = {
426 .name = "twl4030_madc_hwmon",
430 static struct platform_device *omap3_beagle_devices[] __initdata = {
436 static const struct usbhs_omap_board_data usbhs_bdata __initconst = {
438 .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
439 .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
440 .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
443 .reset_gpio_port[0] = -EINVAL,
444 .reset_gpio_port[1] = 147,
445 .reset_gpio_port[2] = -EINVAL
448 #ifdef CONFIG_OMAP_MUX
449 static struct omap_board_mux board_mux[] __initdata = {
450 { .reg_offset = OMAP_MUX_TERMINATOR },
454 static void __init beagle_opp_init(void)
458 /* Initialize the omap3 opp table */
459 if (omap3_opp_init()) {
460 pr_err("%s: opp default init failed\n", __func__);
464 /* Custom OPP enabled for all xM versions */
465 if (cpu_is_omap3630()) {
466 struct device *mpu_dev, *iva_dev;
468 mpu_dev = omap_device_get_by_hwmod_name("mpu");
469 iva_dev = omap_device_get_by_hwmod_name("iva");
471 if (!mpu_dev || !iva_dev) {
472 pr_err("%s: Aiee.. no mpu/dsp devices? %p %p\n",
473 __func__, mpu_dev, iva_dev);
476 /* Enable MPU 1GHz and lower opps */
477 r = opp_enable(mpu_dev, 800000000);
478 /* TODO: MPU 1GHz needs SR and ABB */
480 /* Enable IVA 800MHz and lower opps */
481 r |= opp_enable(iva_dev, 660000000);
482 /* TODO: DSP 800MHz needs SR and ABB */
484 pr_err("%s: failed to enable higher opp %d\n",
487 * Cleanup - disable the higher freqs - we dont care
490 opp_disable(mpu_dev, 800000000);
491 opp_disable(iva_dev, 660000000);
497 static void __init omap3_beagle_init(void)
499 omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
500 omap3_beagle_init_rev();
502 if (beagle_config.mmc1_gpio_wp != -EINVAL)
503 omap_mux_init_gpio(beagle_config.mmc1_gpio_wp, OMAP_PIN_INPUT);
504 mmc[0].caps = beagle_config.mmc_caps;
505 omap_hsmmc_init(mmc);
507 omap3_beagle_i2c_init();
509 gpio_buttons[0].gpio = beagle_config.usr_button_gpio;
511 platform_add_devices(omap3_beagle_devices,
512 ARRAY_SIZE(omap3_beagle_devices));
513 omap_display_init(&beagle_dss_data);
515 omap_sdrc_init(mt46h32m32lf6_sdrc_params,
516 mt46h32m32lf6_sdrc_params);
518 omap_mux_init_gpio(170, OMAP_PIN_INPUT);
519 /* REVISIT leave DVI powered down until it's needed ... */
520 gpio_request_one(170, GPIOF_OUT_INIT_HIGH, "DVI_nPD");
523 usbhs_init(&usbhs_bdata);
524 omap_nand_flash_init(NAND_BUSWIDTH_16, omap3beagle_nand_partitions,
525 ARRAY_SIZE(omap3beagle_nand_partitions));
527 /* Ensure msecure is mux'd to be able to set the RTC. */
528 omap_mux_init_signal("sys_drm_msecure", OMAP_PIN_OFF_OUTPUT_HIGH);
530 /* Ensure SDRC pins are mux'd for self-refresh */
531 omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
532 omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT);
537 MACHINE_START(OMAP3_BEAGLE, "OMAP3 Beagle Board")
538 /* Maintainer: Syed Mohammed Khasim - http://beagleboard.org */
539 .atag_offset = 0x100,
540 .reserve = omap_reserve,
541 .map_io = omap3_map_io,
542 .init_early = omap3_init_early,
543 .init_irq = omap3_init_irq,
544 .handle_irq = omap3_intc_handle_irq,
545 .init_machine = omap3_beagle_init,
546 .init_late = omap3_init_late,
547 .timer = &omap3_secure_timer,
548 .restart = omap_prcm_restart,