Pileus Git - ~andy/linux/blob - arch/arm/mach-omap2/board-3430sdp.c

   1 /*
   2  * linux/arch/arm/mach-omap2/board-3430sdp.c
   3  *
   4  * Copyright (C) 2007 Texas Instruments
   5  *
   6  * Modified from mach-omap2/board-generic.c
   7  *
   8  * Initial code: Syed Mohammed Khasim
   9  *
  10  * This program is free software; you can redistribute it and/or modify
  11  * it under the terms of the GNU General Public License version 2 as
  12  * published by the Free Software Foundation.
  13  */
  14
  15 #include <linux/kernel.h>
  16 #include <linux/init.h>
  17 #include <linux/platform_device.h>
  18 #include <linux/delay.h>
  19 #include <linux/input.h>
  20 #include <linux/input/matrix_keypad.h>
  21 #include <linux/spi/spi.h>
  22 #include <linux/i2c/twl.h>
  23 #include <linux/regulator/machine.h>
  24 #include <linux/io.h>
  25 #include <linux/gpio.h>
  26 #include <linux/mmc/host.h>
  27 #include <linux/platform_data/spi-omap2-mcspi.h>
  28 #include <linux/platform_data/omap-twl4030.h>
  29 #include <linux/usb/phy.h>
  30
  31 #include <asm/mach-types.h>
  32 #include <asm/mach/arch.h>
  33 #include <asm/mach/map.h>
  34
  35 #include "common.h"
  36 #include <linux/omap-dma.h>
  37 #include <video/omapdss.h>
  38 #include <video/omap-panel-data.h>
  39
  40 #include "gpmc.h"
  41 #include "gpmc-smc91x.h"
  42
  43 #include "soc.h"
  44 #include "board-flash.h"
  45 #include "mux.h"
  46 #include "sdram-qimonda-hyb18m512160af-6.h"
  47 #include "hsmmc.h"
  48 #include "pm.h"
  49 #include "control.h"
  50 #include "common-board-devices.h"
  51
  52 #define CONFIG_DISABLE_HFCLK 1
  53
  54 #define SDP3430_TS_GPIO_IRQ_SDPV1       3
  55 #define SDP3430_TS_GPIO_IRQ_SDPV2       2
  56
  57 #define ENABLE_VAUX3_DEDICATED  0x03
  58 #define ENABLE_VAUX3_DEV_GRP    0x20
  59
  60 #define TWL4030_MSECURE_GPIO 22
  61
  62 static uint32_t board_keymap[] = {
  63         KEY(0, 0, KEY_LEFT),
  64         KEY(0, 1, KEY_RIGHT),
  65         KEY(0, 2, KEY_A),
  66         KEY(0, 3, KEY_B),
  67         KEY(0, 4, KEY_C),
  68         KEY(1, 0, KEY_DOWN),
  69         KEY(1, 1, KEY_UP),
  70         KEY(1, 2, KEY_E),
  71         KEY(1, 3, KEY_F),
  72         KEY(1, 4, KEY_G),
  73         KEY(2, 0, KEY_ENTER),
  74         KEY(2, 1, KEY_I),
  75         KEY(2, 2, KEY_J),
  76         KEY(2, 3, KEY_K),
  77         KEY(2, 4, KEY_3),
  78         KEY(3, 0, KEY_M),
  79         KEY(3, 1, KEY_N),
  80         KEY(3, 2, KEY_O),
  81         KEY(3, 3, KEY_P),
  82         KEY(3, 4, KEY_Q),
  83         KEY(4, 0, KEY_R),
  84         KEY(4, 1, KEY_4),
  85         KEY(4, 2, KEY_T),
  86         KEY(4, 3, KEY_U),
  87         KEY(4, 4, KEY_D),
  88         KEY(5, 0, KEY_V),
  89         KEY(5, 1, KEY_W),
  90         KEY(5, 2, KEY_L),
  91         KEY(5, 3, KEY_S),
  92         KEY(5, 4, KEY_H),
  93         0
  94 };
  95
  96 static struct matrix_keymap_data board_map_data = {
  97         .keymap                 = board_keymap,
  98         .keymap_size            = ARRAY_SIZE(board_keymap),
  99 };
 100
 101 static struct twl4030_keypad_data sdp3430_kp_data = {
 102         .keymap_data    = &board_map_data,
 103         .rows           = 5,
 104         .cols           = 6,
 105         .rep            = 1,
 106 };
 107
 108 #define SDP3430_LCD_PANEL_BACKLIGHT_GPIO        8
 109 #define SDP3430_LCD_PANEL_ENABLE_GPIO           5
 110
 111 static void __init sdp3430_display_init(void)
 112 {
 113         int r;
 114
 115         /*
 116          * the backlight GPIO doesn't directly go to the panel, it enables
 117          * an internal circuit on 3430sdp to create the signal V_BKL_28V,
 118          * this is connected to LED+ pin of the sharp panel. This GPIO
 119          * is left enabled in the board file, and not passed to the panel
 120          * as platform_data.
 121          */
 122         r = gpio_request_one(SDP3430_LCD_PANEL_BACKLIGHT_GPIO,
 123                                 GPIOF_OUT_INIT_HIGH, "LCD Backlight");
 124         if (r)
 125                 pr_err("failed to get LCD Backlight GPIO\n");
 126
 127 }
 128
 129 static struct panel_sharp_ls037v7dw01_data sdp3430_lcd_data = {
 130         .resb_gpio = SDP3430_LCD_PANEL_ENABLE_GPIO,
 131         .ini_gpio = -1,
 132         .mo_gpio = -1,
 133         .lr_gpio = -1,
 134         .ud_gpio = -1,
 135 };
 136
 137 static struct omap_dss_device sdp3430_lcd_device = {
 138         .name                   = "lcd",
 139         .driver_name            = "sharp_ls_panel",
 140         .type                   = OMAP_DISPLAY_TYPE_DPI,
 141         .phy.dpi.data_lines     = 16,
 142         .data                   = &sdp3430_lcd_data,
 143 };
 144
 145 static struct tfp410_platform_data dvi_panel = {
 146         .power_down_gpio        = -1,
 147         .i2c_bus_num            = -1,
 148 };
 149
 150 static struct omap_dss_device sdp3430_dvi_device = {
 151         .name                   = "dvi",
 152         .type                   = OMAP_DISPLAY_TYPE_DPI,
 153         .driver_name            = "tfp410",
 154         .data                   = &dvi_panel,
 155         .phy.dpi.data_lines     = 24,
 156 };
 157
 158 static struct omap_dss_device sdp3430_tv_device = {
 159         .name                   = "tv",
 160         .driver_name            = "venc",
 161         .type                   = OMAP_DISPLAY_TYPE_VENC,
 162         .phy.venc.type          = OMAP_DSS_VENC_TYPE_SVIDEO,
 163 };
 164
 165
 166 static struct omap_dss_device *sdp3430_dss_devices[] = {
 167         &sdp3430_lcd_device,
 168         &sdp3430_dvi_device,
 169         &sdp3430_tv_device,
 170 };
 171
 172 static struct omap_dss_board_info sdp3430_dss_data = {
 173         .num_devices    = ARRAY_SIZE(sdp3430_dss_devices),
 174         .devices        = sdp3430_dss_devices,
 175         .default_device = &sdp3430_lcd_device,
 176 };
 177
 178 static struct omap2_hsmmc_info mmc[] = {
 179         {
 180                 .mmc            = 1,
 181                 /* 8 bits (default) requires S6.3 == ON,
 182                  * so the SIM card isn't used; else 4 bits.
 183                  */
 184                 .caps           = MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
 185                 .gpio_wp        = 4,
 186                 .deferred       = true,
 187         },
 188         {
 189                 .mmc            = 2,
 190                 .caps           = MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
 191                 .gpio_wp        = 7,
 192                 .deferred       = true,
 193         },
 194         {}      /* Terminator */
 195 };
 196
 197 static struct omap_tw4030_pdata omap_twl4030_audio_data = {
 198         .voice_connected = true,
 199         .custom_routing = true,
 200
 201         .has_hs         = OMAP_TWL4030_LEFT | OMAP_TWL4030_RIGHT,
 202         .has_hf         = OMAP_TWL4030_LEFT | OMAP_TWL4030_RIGHT,
 203
 204         .has_mainmic    = true,
 205         .has_submic     = true,
 206         .has_hsmic      = true,
 207         .has_linein     = OMAP_TWL4030_LEFT | OMAP_TWL4030_RIGHT,
 208 };
 209
 210 static int sdp3430_twl_gpio_setup(struct device *dev,
 211                 unsigned gpio, unsigned ngpio)
 212 {
 213         /* gpio + 0 is "mmc0_cd" (input/IRQ),
 214          * gpio + 1 is "mmc1_cd" (input/IRQ)
 215          */
 216         mmc[0].gpio_cd = gpio + 0;
 217         mmc[1].gpio_cd = gpio + 1;
 218         omap_hsmmc_late_init(mmc);
 219
 220         /* gpio + 7 is "sub_lcd_en_bkl" (output/PWM1) */
 221         gpio_request_one(gpio + 7, GPIOF_OUT_INIT_LOW, "sub_lcd_en_bkl");
 222
 223         /* gpio + 15 is "sub_lcd_nRST" (output) */
 224         gpio_request_one(gpio + 15, GPIOF_OUT_INIT_LOW, "sub_lcd_nRST");
 225
 226         omap_twl4030_audio_data.jack_detect = gpio + 2;
 227         omap_twl4030_audio_init("SDP3430", &omap_twl4030_audio_data);
 228
 229         return 0;
 230 }
 231
 232 static struct twl4030_gpio_platform_data sdp3430_gpio_data = {
 233         .pulldowns      = BIT(2) | BIT(6) | BIT(8) | BIT(13)
 234                                 | BIT(16) | BIT(17),
 235         .setup          = sdp3430_twl_gpio_setup,
 236 };
 237
 238 /* regulator consumer mappings */
 239
 240 /* ads7846 on SPI */
 241 static struct regulator_consumer_supply sdp3430_vaux3_supplies[] = {
 242         REGULATOR_SUPPLY("vcc", "spi1.0"),
 243 };
 244
 245 static struct regulator_consumer_supply sdp3430_vmmc1_supplies[] = {
 246         REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
 247 };
 248
 249 static struct regulator_consumer_supply sdp3430_vsim_supplies[] = {
 250         REGULATOR_SUPPLY("vmmc_aux", "omap_hsmmc.0"),
 251 };
 252
 253 static struct regulator_consumer_supply sdp3430_vmmc2_supplies[] = {
 254         REGULATOR_SUPPLY("vmmc", "omap_hsmmc.1"),
 255 };
 256
 257 /*
 258  * Apply all the fixed voltages since most versions of U-Boot
 259  * don't bother with that initialization.
 260  */
 261
 262 /* VAUX1 for mainboard (irda and sub-lcd) */
 263 static struct regulator_init_data sdp3430_vaux1 = {
 264         .constraints = {
 265                 .min_uV                 = 2800000,
 266                 .max_uV                 = 2800000,
 267                 .apply_uV               = true,
 268                 .valid_modes_mask       = REGULATOR_MODE_NORMAL
 269                                         | REGULATOR_MODE_STANDBY,
 270                 .valid_ops_mask         = REGULATOR_CHANGE_MODE
 271                                         | REGULATOR_CHANGE_STATUS,
 272         },
 273 };
 274
 275 /* VAUX2 for camera module */
 276 static struct regulator_init_data sdp3430_vaux2 = {
 277         .constraints = {
 278                 .min_uV                 = 2800000,
 279                 .max_uV                 = 2800000,
 280                 .apply_uV               = true,
 281                 .valid_modes_mask       = REGULATOR_MODE_NORMAL
 282                                         | REGULATOR_MODE_STANDBY,
 283                 .valid_ops_mask         = REGULATOR_CHANGE_MODE
 284                                         | REGULATOR_CHANGE_STATUS,
 285         },
 286 };
 287
 288 /* VAUX3 for LCD board */
 289 static struct regulator_init_data sdp3430_vaux3 = {
 290         .constraints = {
 291                 .min_uV                 = 2800000,
 292                 .max_uV                 = 2800000,
 293                 .apply_uV               = true,
 294                 .valid_modes_mask       = REGULATOR_MODE_NORMAL
 295                                         | REGULATOR_MODE_STANDBY,
 296                 .valid_ops_mask         = REGULATOR_CHANGE_MODE
 297                                         | REGULATOR_CHANGE_STATUS,
 298         },
 299         .num_consumer_supplies          = ARRAY_SIZE(sdp3430_vaux3_supplies),
 300         .consumer_supplies              = sdp3430_vaux3_supplies,
 301 };
 302
 303 /* VAUX4 for OMAP VDD_CSI2 (camera) */
 304 static struct regulator_init_data sdp3430_vaux4 = {
 305         .constraints = {
 306                 .min_uV                 = 1800000,
 307                 .max_uV                 = 1800000,
 308                 .apply_uV               = true,
 309                 .valid_modes_mask       = REGULATOR_MODE_NORMAL
 310                                         | REGULATOR_MODE_STANDBY,
 311                 .valid_ops_mask         = REGULATOR_CHANGE_MODE
 312                                         | REGULATOR_CHANGE_STATUS,
 313         },
 314 };
 315
 316 /* VMMC1 for OMAP VDD_MMC1 (i/o) and MMC1 card */
 317 static struct regulator_init_data sdp3430_vmmc1 = {
 318         .constraints = {
 319                 .min_uV                 = 1850000,
 320                 .max_uV                 = 3150000,
 321                 .valid_modes_mask       = REGULATOR_MODE_NORMAL
 322                                         | REGULATOR_MODE_STANDBY,
 323                 .valid_ops_mask         = REGULATOR_CHANGE_VOLTAGE
 324                                         | REGULATOR_CHANGE_MODE
 325                                         | REGULATOR_CHANGE_STATUS,
 326         },
 327         .num_consumer_supplies  = ARRAY_SIZE(sdp3430_vmmc1_supplies),
 328         .consumer_supplies      = sdp3430_vmmc1_supplies,
 329 };
 330
 331 /* VMMC2 for MMC2 card */
 332 static struct regulator_init_data sdp3430_vmmc2 = {
 333         .constraints = {
 334                 .min_uV                 = 1850000,
 335                 .max_uV                 = 1850000,
 336                 .apply_uV               = true,
 337                 .valid_modes_mask       = REGULATOR_MODE_NORMAL
 338                                         | REGULATOR_MODE_STANDBY,
 339                 .valid_ops_mask         = REGULATOR_CHANGE_MODE
 340                                         | REGULATOR_CHANGE_STATUS,
 341         },
 342         .num_consumer_supplies  = ARRAY_SIZE(sdp3430_vmmc2_supplies),
 343         .consumer_supplies      = sdp3430_vmmc2_supplies,
 344 };
 345
 346 /* VSIM for OMAP VDD_MMC1A (i/o for DAT4..DAT7) */
 347 static struct regulator_init_data sdp3430_vsim = {
 348         .constraints = {
 349                 .min_uV                 = 1800000,
 350                 .max_uV                 = 3000000,
 351                 .valid_modes_mask       = REGULATOR_MODE_NORMAL
 352                                         | REGULATOR_MODE_STANDBY,
 353                 .valid_ops_mask         = REGULATOR_CHANGE_VOLTAGE
 354                                         | REGULATOR_CHANGE_MODE
 355                                         | REGULATOR_CHANGE_STATUS,
 356         },
 357         .num_consumer_supplies  = ARRAY_SIZE(sdp3430_vsim_supplies),
 358         .consumer_supplies      = sdp3430_vsim_supplies,
 359 };
 360
 361 static struct twl4030_platform_data sdp3430_twldata = {
 362         /* platform_data for children goes here */
 363         .gpio           = &sdp3430_gpio_data,
 364         .keypad         = &sdp3430_kp_data,
 365
 366         .vaux1          = &sdp3430_vaux1,
 367         .vaux2          = &sdp3430_vaux2,
 368         .vaux3          = &sdp3430_vaux3,
 369         .vaux4          = &sdp3430_vaux4,
 370         .vmmc1          = &sdp3430_vmmc1,
 371         .vmmc2          = &sdp3430_vmmc2,
 372         .vsim           = &sdp3430_vsim,
 373 };
 374
 375 static int __init omap3430_i2c_init(void)
 376 {
 377         /* i2c1 for PMIC only */
 378         omap3_pmic_get_config(&sdp3430_twldata,
 379                         TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_BCI |
 380                         TWL_COMMON_PDATA_MADC | TWL_COMMON_PDATA_AUDIO,
 381                         TWL_COMMON_REGULATOR_VDAC | TWL_COMMON_REGULATOR_VPLL2);
 382         sdp3430_twldata.vdac->constraints.apply_uV = true;
 383         sdp3430_twldata.vpll2->constraints.apply_uV = true;
 384         sdp3430_twldata.vpll2->constraints.name = "VDVI";
 385
 386         sdp3430_twldata.audio->codec->hs_extmute = 1;
 387         sdp3430_twldata.audio->codec->hs_extmute_gpio = -EINVAL;
 388
 389         omap3_pmic_init("twl4030", &sdp3430_twldata);
 390
 391         /* i2c2 on camera connector (for sensor control) and optional isp1301 */
 392         omap_register_i2c_bus(2, 400, NULL, 0);
 393         /* i2c3 on display connector (for DVI, tfp410) */
 394         omap_register_i2c_bus(3, 400, NULL, 0);
 395         return 0;
 396 }
 397
 398 #if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
 399
 400 static struct omap_smc91x_platform_data board_smc91x_data = {
 401         .cs             = 3,
 402         .flags          = GPMC_MUX_ADD_DATA | GPMC_TIMINGS_SMC91C96 |
 403                                 IORESOURCE_IRQ_LOWLEVEL,
 404 };
 405
 406 static void __init board_smc91x_init(void)
 407 {
 408         if (omap_rev() > OMAP3430_REV_ES1_0)
 409                 board_smc91x_data.gpio_irq = 6;
 410         else
 411                 board_smc91x_data.gpio_irq = 29;
 412
 413         gpmc_smc91x_init(&board_smc91x_data);
 414 }
 415
 416 #else
 417
 418 static inline void board_smc91x_init(void)
 419 {
 420 }
 421
 422 #endif
 423
 424 static void enable_board_wakeup_source(void)
 425 {
 426         /* T2 interrupt line (keypad) */
 427         omap_mux_init_signal("sys_nirq",
 428                 OMAP_WAKEUP_EN | OMAP_PIN_INPUT_PULLUP);
 429 }
 430
 431 static struct usbhs_phy_data phy_data[] __initdata = {
 432         {
 433                 .port = 1,
 434                 .reset_gpio = 57,
 435                 .vcc_gpio = -EINVAL,
 436         },
 437         {
 438                 .port = 2,
 439                 .reset_gpio = 61,
 440                 .vcc_gpio = -EINVAL,
 441         },
 442 };
 443
 444 static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
 445
 446         .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
 447         .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
 448 };
 449
 450 #ifdef CONFIG_OMAP_MUX
 451 static struct omap_board_mux board_mux[] __initdata = {
 452         { .reg_offset = OMAP_MUX_TERMINATOR },
 453 };
 454 #else
 455 #define board_mux       NULL
 456 #endif
 457
 458 /*
 459  * SDP3430 V2 Board CS organization
 460  * Different from SDP3430 V1. Now 4 switches used to specify CS
 461  *
 462  * See also the Switch S8 settings in the comments.
 463  */
 464 static char chip_sel_3430[][GPMC_CS_NUM] = {
 465         {PDC_NOR, PDC_NAND, PDC_ONENAND, DBG_MPDB, 0, 0, 0, 0}, /* S8:1111 */
 466         {PDC_ONENAND, PDC_NAND, PDC_NOR, DBG_MPDB, 0, 0, 0, 0}, /* S8:1110 */
 467         {PDC_NAND, PDC_ONENAND, PDC_NOR, DBG_MPDB, 0, 0, 0, 0}, /* S8:1101 */
 468 };
 469
 470 static struct mtd_partition sdp_nor_partitions[] = {
 471         /* bootloader (U-Boot, etc) in first sector */
 472         {
 473                 .name           = "Bootloader-NOR",
 474                 .offset         = 0,
 475                 .size           = SZ_256K,
 476                 .mask_flags     = MTD_WRITEABLE, /* force read-only */
 477         },
 478         /* bootloader params in the next sector */
 479         {
 480                 .name           = "Params-NOR",
 481                 .offset         = MTDPART_OFS_APPEND,
 482                 .size           = SZ_256K,
 483                 .mask_flags     = 0,
 484         },
 485         /* kernel */
 486         {
 487                 .name           = "Kernel-NOR",
 488                 .offset         = MTDPART_OFS_APPEND,
 489                 .size           = SZ_2M,
 490                 .mask_flags     = 0
 491         },
 492         /* file system */
 493         {
 494                 .name           = "Filesystem-NOR",
 495                 .offset         = MTDPART_OFS_APPEND,
 496                 .size           = MTDPART_SIZ_FULL,
 497                 .mask_flags     = 0
 498         }
 499 };
 500
 501 static struct mtd_partition sdp_onenand_partitions[] = {
 502         {
 503                 .name           = "X-Loader-OneNAND",
 504                 .offset         = 0,
 505                 .size           = 4 * (64 * 2048),
 506                 .mask_flags     = MTD_WRITEABLE  /* force read-only */
 507         },
 508         {
 509                 .name           = "U-Boot-OneNAND",
 510                 .offset         = MTDPART_OFS_APPEND,
 511                 .size           = 2 * (64 * 2048),
 512                 .mask_flags     = MTD_WRITEABLE  /* force read-only */
 513         },
 514         {
 515                 .name           = "U-Boot Environment-OneNAND",
 516                 .offset         = MTDPART_OFS_APPEND,
 517                 .size           = 1 * (64 * 2048),
 518         },
 519         {
 520                 .name           = "Kernel-OneNAND",
 521                 .offset         = MTDPART_OFS_APPEND,
 522                 .size           = 16 * (64 * 2048),
 523         },
 524         {
 525                 .name           = "File System-OneNAND",
 526                 .offset         = MTDPART_OFS_APPEND,
 527                 .size           = MTDPART_SIZ_FULL,
 528         },
 529 };
 530
 531 static struct mtd_partition sdp_nand_partitions[] = {
 532         /* All the partition sizes are listed in terms of NAND block size */
 533         {
 534                 .name           = "X-Loader-NAND",
 535                 .offset         = 0,
 536                 .size           = 4 * (64 * 2048),
 537                 .mask_flags     = MTD_WRITEABLE,        /* force read-only */
 538         },
 539         {
 540                 .name           = "U-Boot-NAND",
 541                 .offset         = MTDPART_OFS_APPEND,   /* Offset = 0x80000 */
 542                 .size           = 10 * (64 * 2048),
 543                 .mask_flags     = MTD_WRITEABLE,        /* force read-only */
 544         },
 545         {
 546                 .name           = "Boot Env-NAND",
 547
 548                 .offset         = MTDPART_OFS_APPEND,   /* Offset = 0x1c0000 */
 549                 .size           = 6 * (64 * 2048),
 550         },
 551         {
 552                 .name           = "Kernel-NAND",
 553                 .offset         = MTDPART_OFS_APPEND,   /* Offset = 0x280000 */
 554                 .size           = 40 * (64 * 2048),
 555         },
 556         {
 557                 .name           = "File System - NAND",
 558                 .size           = MTDPART_SIZ_FULL,
 559                 .offset         = MTDPART_OFS_APPEND,   /* Offset = 0x780000 */
 560         },
 561 };
 562
 563 static struct flash_partitions sdp_flash_partitions[] = {
 564         {
 565                 .parts = sdp_nor_partitions,
 566                 .nr_parts = ARRAY_SIZE(sdp_nor_partitions),
 567         },
 568         {
 569                 .parts = sdp_onenand_partitions,
 570                 .nr_parts = ARRAY_SIZE(sdp_onenand_partitions),
 571         },
 572         {
 573                 .parts = sdp_nand_partitions,
 574                 .nr_parts = ARRAY_SIZE(sdp_nand_partitions),
 575         },
 576 };
 577
 578 static void __init omap_3430sdp_init(void)
 579 {
 580         int gpio_pendown;
 581
 582         omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
 583         omap_hsmmc_init(mmc);
 584         omap3430_i2c_init();
 585         omap_display_init(&sdp3430_dss_data);
 586         if (omap_rev() > OMAP3430_REV_ES1_0)
 587                 gpio_pendown = SDP3430_TS_GPIO_IRQ_SDPV2;
 588         else
 589                 gpio_pendown = SDP3430_TS_GPIO_IRQ_SDPV1;
 590         omap_ads7846_init(1, gpio_pendown, 310, NULL);
 591         omap_serial_init();
 592         omap_sdrc_init(hyb18m512160af6_sdrc_params, NULL);
 593         usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
 594         usb_musb_init(NULL);
 595         board_smc91x_init();
 596         board_flash_init(sdp_flash_partitions, chip_sel_3430, 0);
 597         sdp3430_display_init();
 598         enable_board_wakeup_source();
 599
 600         usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
 601         usbhs_init(&usbhs_bdata);
 602 }
 603
 604 MACHINE_START(OMAP_3430SDP, "OMAP3430 3430SDP board")
 605         /* Maintainer: Syed Khasim - Texas Instruments Inc */
 606         .atag_offset    = 0x100,
 607         .reserve        = omap_reserve,
 608         .map_io         = omap3_map_io,
 609         .init_early     = omap3430_init_early,
 610         .init_irq       = omap3_init_irq,
 611         .handle_irq     = omap3_intc_handle_irq,
 612         .init_machine   = omap_3430sdp_init,
 613         .init_late      = omap3430_init_late,
 614         .init_time      = omap3_sync32k_timer_init,
 615         .restart        = omap3xxx_restart,
 616 MACHINE_END